VEC192
ONE YEAR LIMITED WARRANTY PROGRAM
This limited warranty program is the only one that applies to this product, and it sets forth all the
responsibilities of Vector Products, Inc., regarding this product. There is no other warranty, other than those
described herein. Any implied warranty of merchantability or fitness for a particular purpose on this product
is limited in duration to the duration of this warranty.
This Vector Products, Inc. product is warranted, to the original purchaser only, to be free of defects in
materials and workmanship for one year from the date of purchase without additional charge. The
warranty does not extend to subsequent purchasers or users. Manufacturer will not be responsible for any
amount of damage in excess of the retail purchase price of the product under any circumstances. Incidental
and consequential damages are specifically excluded from coverage under this warranty.
This product is not intended for commercial use. This warranty does not apply to damage to units from
misuse or incorrect installation/connection. Misuse includes wiring or connecting to improper polarity
power sources.
Twin Beam Rechargeable
®
SportSpot
™
20,000,000 Power Series
RETURN/REPAIR POLICY: Defective products may be returned to manufacturer. Any defective product that
is returned to manufacturer within 30 days of the date of purchase will be replaced free of charge. If such
a product is returned more than 30 days but less than one year from the purchase date, manufacturer will
repair the unit or, at its option, replace it, free of charge.
If the unit is repaired, new or reconditioned replacement parts may be used, at manufacturer’s option. A
unit may be replaced with a new or reconditioned unit of the same or comparable design. The repaired or
replaced unit will then be warranted under the terms of the remainder of the warranty period. The customer
is responsible for the shipping charges on all returned items. During the warranty period, manufacturer will
be responsible for the return shipping charges to the customer in the United States.
LIMITATIONS: This warranty does not cover accessories, such as charging adapters, bulbs, fuses and
batteries, damage or defects resulting from normal wear and tear (including chips, scratches, abrasions,
discoloration or fading due to usage or exposure to sunlight), accidents, damage during shipping to our
service facility, alterations, unauthorized use or repair, neglect, misuse, abuse, failure to follow instructions
for care and maintenance, fire, flood and Acts of God.
If your problem is not covered by this warranty, call our Technical Support Department toll free at (800)
544-6986 for general repair information and charges if applicable.
STATE LAW RIGHTS: This warranty gives you specific legal rights. Some states do not allow limitations on
how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages,
so the exclusions or limitations stated herein may not apply. This warranty gives the purchaser specific legal
rights; other rights, which vary from state to state, may apply.
TO REQUEST WARRANTY SERVICE FOR THIS PRODUCT: Contact Technical Support by telephone, fax or
mail (see below). We suggest that you keep the original packaging in case you need to ship the unit. When
returning a product, include your name, address, phone number, dated sales receipt (or copy) and a
description of the reason for return and product serial number. After repairing or replacing the unit, we will
make every effort to return it to you within four weeks.
WARRANTY ACTIVATION: Please complete Warranty Activation Card and mail to Vector Products, Inc..
Enter “VEC192” as Model and “Twin Beam Rechargeable SportSpot® 20,000,000 Power Series™” as
Product Type. All Vector products must be registered within 30 days of purchase to activate this warranty.
Mail the completed registration form, along with a copy of the original sales receipt, to:
USER’S MANUAL
BLACK & DECKER
& WARRANTY INFORMATION
4409 W. Wanda, McAllen, TX 78503
• TOLL FREE: (800) 544-6986 • FAX: (956) 630-0492 •
IMPORTANT SAFETY INFORMATION, SAVE THESE INSTRUCTIONS
WARRANTY IS NON-TRANSFERABLE.
TO REDUCE THE RISK OF INJURY, USER MUST READ AND UNDERSTAND
THIS INSTRUCTIONAL MANUAL. THIS MANUAL CONTAINS IMPORTANT
INFORMATION REGARDING THE OPERATION AND WARRANTY OF THIS
PRODUCT. PLEASE RETAIN FOR FUTURE REFERENCE.
RD121306
4140 S.W. 30th Ave., Ft. Lauderdale, FL 33312
Toll Free: (800) 544-6986
© 2007 VECTOR PRODUCTS, INC.
MADE IN CHINA
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Charging the Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Checking Battery Charge Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
120 Volt AC Charging/Recharging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
12 Volt DC Charging/Recharging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Operating Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Using the Spotlight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Using the 3-LED Auxiliary Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Using the 12 Volt DC Accessory Outlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Using the Adjustable Workstand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Care and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Replacement Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Bulb Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Battery Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Battery Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
DC Plug Fuse Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7
INTRODUCTION
Congratulations on purchasing the Twin Beam Rechargeable SportSpot
®
™
20,000,000 Power Series , an advanced design, dual bulb Spotlight and long
lasting, 3-LED Auxiliary Light. It uses a powerful, proven-technology, rechargeable,
non-spillable, sealed, lead acid battery for years of dependable use. It was designed
to be the most versatile and practical light for travel, camping, picnicking, tailgate
parties and boating. Extremely rugged construction protects the unit from most
vibration and shock damage.
FEATURES
• Two powerful, prefocused, replaceable quartz halogen bulbs
• Single and dual beam Spotlight switches
• Long-life, ultra bright 3-LED Auxiliary Light
• 12 Volt DC Accessory Outlet
• Replaceable, sealed lead acid battery
• 120 Volt AC Recharge Adapter and power cord
• Fused 12 Volt DC Recharge Adapter
• LED Charging Indicators
• Removable carry strap
• Protective rubber safety guard (bezel) around lens
• Hands-free adjustable workstand with position locks
Download from Www.Somanuals.com. All Manuals Search And Download.
1
It is recommended that you charge the Spotlight after each use (or every 2 months
when not in frequent use) until the green LED lights so the unit is always ready when
you need it.
LED AUXILIARY LIGHT
ON/OFF PUSHBUTTON
EASY GRIP
HANDLE
LED CHARGING
INDICATORS
REMOVABLE
AC RECHARGE
CARRY STRAP
PORT
120 Volt AC Charging/Recharging
12 VOLT DC CHARGING/
POWER PORT
3-LED AUXILIARY
Plug the supplied 120 Volt AC Adapter’s plug into a
standard North American outlet. Connect the
Adapter’s DC barrel connector to the AC Recharge
Port located on the top/rear of the grip handle. Time
required to initially charge the unit using this method
is approximately 30 to 35 hours. The green
Charging LED Indicator will light when the unit is fully
charged. The AC charging/recharging method
will not work while the Spotlight is in use.
LIGHT
BATTERY
COMPARTMENT
COVER LOCK
(ONE ON EACH SIDE)
RUBBER
BEZEL
BATTERY
TWIN BEAM
COMPARTMENT
QUARTZ HALOGEN
SPOTLIGHT
ON/OFF SPOTLIGHT
WORKSTAND
POSITION LOCK
KNOBS
ADJUSTABLE
WORKSTAND
SWITCH COMPARTMENT
12 Volt DC Charging/Recharging
(ONE ON EACH SIDE)
The DC recharging method will NOT recharge the
unit as effectively as the 120 volt AC method. This
method is recommended only when it is necessary,
since frequent use of the 12 volt DC recharging
procedure may shorten the battery system’s life.
1. Insert the gold-tipped end plug of the 12 Volt DC
Charging/Power Adapter plug into the vehicle’s
12 volt DC accessory outlet.
CHARGING THE BATTERY
The unit is delivered in a partially charged state. It must be fully charged prior to first
use by either the 120 volt AC method (preferred) or the 12 volt DC method.
After initial charging, the VEC192 can be simultaneously recharged (using the 12
Volt DC method only) and operated. When recharging and operating the Spotlight
at the same time, single beam operation is recommended.
When using the 12 volt DC recharging method, make sure the power source can
supply minimum 15 amperes of current if the Spotlight is to be operated while the
battery is being charged.
After charging, disconnect the Adapter from the external power source, then
disconnect the Adapter from the AC Recharge Port or 12 Volt DC Charging/Power
Port.
2. Insert the silver-tipped end plug into the 12 Volt DC Charging/Power Port on the
back of the handle of the unit.
3. Charging time using this method is approximately 5 to 6 hours.
4. When charging is complete, remove the power cord immediately and return it to
the storage compartment.
The Spotlight CAN be used while recharging using the 12 Volt DC
method. If doing so, single beam operation is recommended.
Notes: When using a vehicle’s 12 volt DC accessory outlet as a charging/power
source, be aware that some vehicles require the ignition be turned on to
power the accessory outlet.
12 VOLT DC CHARGING/
POWER ADAPTER
RED LED
GREEN LED
CHARGING
INDICATOR
CHARGING
INDICATORS
CAUTION
Before connecting either Adapter to the VEC192 to charge or recharge
the unit’s battery, make sure all power switches are in the OFF
position.
AC RECHARGE
PORT
12 VOLT DC
CHARGING/
POWER PORT
120 VOLT
AC ADAPTER
Checking Battery Charge Status
Plugging in either the 120 Volt AC Adapter turns on the LED Charging Indicators. Two
red LEDs indicate a moderate level of charge; and one red LED indicates that the unit
should be charged soon. The green LED lights to show a fully charged unit.
Download from Www.Somanuals.com. All Manuals Search And Download.
2
3
OPERATING INSTRUCTIONS
Using the Spotlight
The twin beam, quartz halogen Spotlight is operated by the two switches located in
the compartment on the side of the unit (see the illustration on page 2). The top
ON/OFF Switch controls the left beam; the bottom ON/OFF Switch controls the right
beam.
CARE AND MAINTENANCE
All batteries lose charge with time, especially when they are warm. Recharge the unit
every two months when not in frequent use, preferably using the 120 volt AC method.
Never submerge the unit in water. If the unit gets dirty, gently clean the outer surfaces of
the spotlight unit with a soft cloth moistened with a mild solution of water and detergent.
Periodically inspect the condition of adapters, connectors and wires. Contact Technical
Support toll-free at (800) 544-6986 to replace any components that have become
worn or broken.
Replacement Parts
The quartz halogen bulb and sealed lead acid battery are available through Vector
Products, Inc.. A comparable (12 volt H7 100 watt) bulb may be substituted. These
can also be purchased from popular automotive parts suppliers nationwide. Contact
Technical Support Department for replacement parts (including replacement adapters
and cords) and any additional information that you may need. They may be reached
toll free at (800) 544-6986.
Using the 3-LED Auxiliary Light
The 3-LED Auxiliary Light is operated by the LED Auxiliary Light ON/OFF Pushbutton
located on the top of the grip handle.
WARNING
To reduce the risk of shocks or burns and avoid damage to the unit,
make sure all power switches are in the OFF position, all adapters are
unplugged and the unit has been allowed to cool down before
performing any maintenance/parts replacement.
Bulb Replacement
To replace either or both H7 type 12 volt 100 watt bulbs, you will need a small
Phillips type screwdriver and a replacement bulb (or bulbs). During installation,
avoid touching the glass part of the bulb. Bulb life may be shortened by installing a
bulb with dirt or fingerprints on it. The bulb can be wiped clean with a cloth
moistened with alcohol.
Using the 12 Volt DC Accessory Outlet
The 12 volt DC accessory outlet powers any DC appliance that does not exceed
5 amps. Flip up the accessory outlet cover and insert the appliance’s DC plug. Close
the cover after use.
1. Disconnect the unit from any charging adapters.
2. Push the rubber bezel forward toward the front of the spotlight to reveal eight
small Phillips screws in the retaining ring.
3. Using the screwdriver, remove (counterclockwise) the screws. Set them aside.
4. Lift off the retaining ring, glass lens and rubber “O” ring and set them aside.
5. Carefully remove the reflector and bulb assembly.
6. Disconnect the wires from the defective bulb.
7. Unsnap the hairpin retaining wires from the reflector’s flange.
8. Lift out the bulb.
Using the Adjustable Workstand
Set the hands-free adjustable workstand to the desired position; then turn the knobs
on either side of the unit to lock in position.
9. Insert the replacement bulb into the reflector’s flange.
10. Put back and secure the hairpin retaining wires.
11. Connect the wires to the bulb.
12. Place the reflector in position in the body of the spotlight.
13. Replace the rubber “O” ring in the groove around the perimeter of the reflector.
14. Replace glass and retaining ring so the screw holes are aligned.
15. Secure retaining ring with the eight screws.
16. Replace rubber bezel.
17. Operate switch to ensure proper operation of Spotlight.
Download from Www.Somanuals.com. All Manuals Search And Download.
4
5
TROUBLESHOOTING
WARNING
To reduce the risk of electric shock, replace bulbs with 12 volt H7 100
watt only.
1. The 120 volt AC charging/recharging method will not work while the Spotlight
is in use.
2. If the unit does not operate, the battery may be completely discharged. Charge
the unit using the AC adapter following the directions in the manual.
Battery Replacement
1. Release the battery compartment cover locks on either side of the unit and
remove the cover.
2. Pull out the battery.
3. If you suspect a bulb is blown, check the bulb filament. If filament is coiled and
unbroken, the bulb is not blown. If filament is blown, replace bulb.
4. If you suspect the main fuse is blown, check it and, if necessary, replace with a
new 20 amp spade fuse.
3. Disconnect the terminals and replace the battery with the same type listed in the
Specifications section of this manual.
4. Replace the battery compartment cover and engage the locks.
SPECIFICATIONS
Spotlight Bulbs:
5. Turn one of the Spotlight’s ON/OFF switches to the ON position to ensure
proper operation of Spotlight.
Two 12 volt, H7 series, 100 watt bulbs
Maintenance-free, sealed lead acid, 12 volt, 7.0 Ah
500mA, 12 volt
Battery:
Battery Disposal
AC Adapter:
Operating Voltage:
Non-spillable sealed lead-acid battery — This battery is fully
recyclable and should be accepted at any location that accepts
common automotive starter batteries. Examples of places that accept
these batteries are: county or municipal recycling drop-off centers,
scrap metal dealers, and retailers who sell automotive replacement
lead acid starter batteries. For more information on recycling this
recycling this battery, call toll-free (877) 288-7722.
12 volts DC
WARNING
Before disposing of the battery, protect exposed terminals with
heavy-duty tape to prevent shorting. (Shorting can result in injury
or fire.)
Do not expose battery to fire or intense heat as it may explode.
DC Plug Fuse Replacement
The fuse in the DC plug protects the charging circuit of the DC recharge adapter. If
the AC recharger operates but the DC charging adapter does not, then the fuse may
be opened.
To replace the fuse:
1. Unscrew the end cap of the DC plug (counterclockwise).
2. Remove spring center contact and fuse.
3. Check fuse with a continuity checker.
4. If blown, locate replacement fuse with same type and rating.
5. Replace the fuse, spring, contact and end cap.
6. Screw end cap clockwise until it is finger tight – DO NOT OVER-TIGHTEN.
7. Check for proper operation of DC charging adapter.
Download from Www.Somanuals.com. All Manuals Search And Download.
6
7
|