®
UNVENTED (VENT-FREE)
PROPANE/LP GAS LOG HEATER
This appliance may be installed in an aftermarket* manufactured (mobile) home,
where not prohibited by state or local codes.
* Aftermarket: Completion of sale, not for purpose of resale, from the manufacturer
OWNER’S OPERATION AND INSTALLATION MANUAL
®
18", 24", and 30"
Remote-Ready
Models
REMOTE
OFF
ON
VS18PR VS24PR VS30PR
WARNING: Improper installation, adjustment,
WARNING: If the information in this manual
alteration, service, or maintenance can cause
is not followed exactly, a fire or explosion
injury or property damage. Refer to this manual
may result causing property damage, per-
for correct installation and operational proce-
sonal injury, or loss of life.
dures. For assistance or additional information
consult a qualified installer, service agency, or
the gas supplier.
— Do not store or use gasoline or other
flammable vapors and liquids in the vicinity
of this or any other appliance.
WARNING: These gas log sets are for installa-
— WHAT TO DO IF YOU SMELL GAS
tion in a masonry solid fuel burning fireplace, a
U.L. listed manufactured solid fuel burning
fireplace or an AGA design certified vent-free
firebox (including LogMate series fireboxes
and stoves) listed for use with these gas log
models.
• Do not try to light any appliance.
• Do not touch any electrical switch; do
not use any phone in your building.
• Immediately call your gas supplier
from a neighbor’s phone. Follow the
gas supplier’s instructions.
WARNING: This is an unvented gas-fired
heater. It uses air (oxygen) from the room in
which it is installed. Provisions for adequate
combustion and ventilation air must be pro-
vided. Refer to “Air for Combustion and Venti-
lation” section in this manual.
• If you cannot reach your gas supplier,
call the fire department.
— Installation and service must be per-
formed by a qualified installer, service
agency, or the gas supplier.
Save this manual for future reference.
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
INFORMATION
Continued
WARNINGS Continued
WARNING: Any change to this heater or its controls can be dangerous.
1. This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not
convertible for use with other gases.
2. Do not place propane supply tank(s) inside any structure. Locate propane supply tank(s) outdoors.
3. If you smell gas
• shut off gas supply
• do not try to light any appliance
• do not touch any electrical switch; do not use any phone in your building
• immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions
• if you cannot reach your gas supplier, call the fire department
4. This heater shall not be installed in a bedroom or bathroom.
5. Never install the heater
• in a recreational vehicle
• where curtains, furniture, clothing, or otherflammable objects are lessthan 36 inches from the front,
top, or sides of the heater
• in high traffic areas
• in windy or drafty areas
6. Beforeinstallinginasolidfuelburningfireplace, thechimneyflueandfireboxmustbecleanedofsoot,
creosote, ashes and loose paint by a qualified chimney cleaner. Creosote will ignite if highly heated.
Inspect chimney flue for damage. If damaged, operate heater with flue damper closed.
7. If fireplace has glass doors, never operate this heater with glass doors closed. If you operate heater with
doors closed, heat buildup inside fireplace will cause glass to burst. Also if fireplace opening has vents
at the bottom, you must open the vents before operating heater.
8. You must operate this heater with a fireplace screen in place. Make sure fireplace screen is closed
before running heater.
9. This log heater is designed to be smokeless. If logs ever appear to smoke, turn off heater and call a
qualified service person. Note: During initial operation, slight smoking may occur due to log curing
and heater burning manufacturing residues.
10. Do not allow fans to blow directly into the fireplace. Avoid any drafts that alter burner flame patterns.
Ceiling fans may create drafts that alter burner flame patterns. Altered burner patterns can cause
sooting.
11. Do not use a blower insert, heat exchanger insert or other accessory not approved for use with this
heater.
12. This heater needs fresh, outside air ventilation to run properly. This heater has an oxygen depletion
sensor (ODS) pilot light safety system. The ODS shuts down the heater if not enough fresh air is
available. See Air for Combustion and Ventilation, pages 5 through 7. If heater keeps shutting off, see
Troubleshooting, pages 23 through 25.
13. Do not run heater
• where flammable liquids or vapors are used or stored
• under dusty conditions
14. Do not use this heater to cook food or burn paper or other objects.
15. Never place any objects on the heater.
16. Heater base assembly becomes very hot when running heater. Keep children and adults away from hot
surface to avoid burns or clothing ignition. Heater will remain hot for a time after shutpdown. Allow
surface to cool before touching.
17. Carefully supervise young children when they are in the room with heater. When using the hand-held
remote accessory, keep remote selector switch in the OFF position to prevent children from turning
on burners with hand-held remote control unit.
18. Do not use heater if any part has been exposed to or under water. Immediately call a qualified service
technician to inspect the room heater and to replace any part of the control system and any gas control
which has been under water.
19. Do not operate heater if any log is broken. Do not operate heater if a log is chipped (dime-sized or
larger).
20. Turnheateroffandletcoolbeforeservicing, installing, orrepairing. Whenusingthehand-heldremote
accessory, make sure the remote selector switch is in the OFF position. Only a qualified service person
should install, service, or repair heater.
21. When using the hand-held remote accessory, make sure the remote selector switch is in the OFF
position when you are away from home for long periods of time.
22. This heater must not be connected to any external electrical source.
23. Operating heater above elevations of 4,500 feet may cause pilot outage.
24. To prevent performance problems, the use of a propane fuel tank of less than 100 lb. capacity is not
recommended.
3
103448
Download from Www.Somanuals.com. All Manuals Search And Download.
Crossover Log
PRODUCT
IDENTIFICATION
Top Middle
Log
Rear Log
Left
Front
Branch
Front
Burner
Rear
Burner
Piezo Ignitor
Bottom
Middle
Log
HI
TEMP
MAN
LO
AU
T
O
ON
OFF
ST
A
TUS
Right Front
Branch
Remote
Control
Control Knob
Base
Assembly
(Optional)
Flame
Adjustment
Knob
Remote
Selector
Switch
(Optional)
Figure 1 - VS24PR Shown
Install and use heater with care. Follow all local codes. In the absence of local codes, use the latest edition
of The National Fuel Gas Code ANSI Z223, also known as NFPA 54*.
LOCAL CODES
UNPACKING
*Available from:
American National Standards Institute, Inc.
1430 Broadway
National Fire Protection Association, Inc.
Batterymarch Park
New York, NY 10018
Quincy, MA 02269
Note: Where listed vented decorative logs are required, thermostat operation is not permitted.
1. Remove logs and heater base assembly from carton. Note: Do not pick up heater base assembly by
burners. This could damage heater. Always handle base assembly by grate.
2. Remove all protective packaging applied to logs and heater for shipment.
3. Check all items for any shipping damage. If damaged, promptly inform dealer where you bought
heater.
Operation
PRODUCT
FEATURES
This heater is clean burning. It requires no outside venting. There is no heat loss out a vent or up a
chimney. Heat is generated by both realistic flames and glowing coals. This heater is designed for vent-
free operation with flue damper closed. State and local codes in some areas prohibit the use of vent-free
heaters.
Safety Pilot
This heater has a pilot with an Oxygen Depletion Sensor Shutoff System (ODS). The ODS/pilot is a required
feature for vent-free room heaters. The ODS/pilot shuts off the heater if there is not enough fresh air.
Piezo Ignition System
This heater has a piezo ignitor. This system requires no matches, batteries, or other sources to light heater.
4
103448
Download from Www.Somanuals.com. All Manuals Search And Download.
AIR FOR
COMBUSTION
AND
WARNING
This heater shall not be installed in a confined space unless provisions are provided for
adequate combustion and ventilation air. Read the following instructions to insure proper
fresh air for this and other fuel-burning appliances in your home.
VENTILATION
Today’s homes are built more energy efficient than ever. New materials, increased insulation, and new
construction methods help reduce heat loss in homes. Home owners weather strip and caulk around
windows and doors to keep the cold air out and the warm air in. During heating months, home owners
want their homes as airtight as possible.
While it is good to make your home energy efficient, your home needs to breathe. Fresh air must enter
your home. All fuel-burning appliances need fresh air for proper combustion and ventilation.
Exhaust fans, fireplaces, clothes dryers, and fuel burning appliances draw air from the house to operate.
You must provide adequate fresh air for these appliances. This will insure proper venting of vented fuel-
burning appliances.
PROVIDING ADEQUATE VENTILATION
The following is exerpts from National Fuel Gas Code. NFPA 54/ANSI Z223.1, Section 5.3, Air for
Combustion and Ventilation.
All spaces in homes fall into one of the three following ventilation classifications:
1. Unusually Tight Contruction
2. Unconfined Space
3. Confined Space
The information on pages 5 through 7 will help you classify your space and provide adequate ventilation.
Unusually Tight Construction
The air that leaks around doors and windows may provide enough fresh air for combustion and ventila-
tion. However, in buildings of unusually tight construction, you must provide additional fresh air.
Unusually tight construction is defined as construction where:
a. walls and ceilings exposed to the outside atmosphere have a continuous water vapor
retarder with a rating of one perm (6x10-11 per pa-sec-m2) or less with openings
gasketed or sealed and
b. weather stripping has been added on openable windows and doors and
c. caulking or sealants are applied to areas such as joints around window and door frames,
between sole plates and floors, between wall-ceiling joints, between wall panels, at
penetrations for plumbing, electrical, and gas lines, and at other openings.
If your home meets all of the three criteria above, you must provide additional fresh air. See
Ventilation Air From Outdoors, page 7.
If your home does not meet all of the three criteria above, continue reading.
Confined Unconfined Space
The National Fuel Gas Code (ANSIZ223.1, 1992 Section 5.3) defines a confined space as a space whose
volume is less than 50 cubic feet per 1,000 Btu per hour (4.8 m3 per kw) of the aggregate input rating of
all appliances installed in that space and an unconfined space as a space whose volume is not less than 50
cubic feet per 1,000 Btu per hour (4.8 m3 per kw) of the aggregate input rating of all appliances installed
in that space. Rooms communicating directly with the space in which the appliances are installed*,
through openings not furnished with doors, are considered a part of the unconfined space.
* Adjoining rooms are communicating only if there are doorless passageways or ventilation grills between
them.
Continued
5
103448
Download from Www.Somanuals.com. All Manuals Search And Download.
DETERMINING AIR FLOW FOR HEATER LOCATION
Determining if You Have a Confined or Unconfined Space
Use this work sheet to determine if you have a confined or unconfined space.
AIR FOR
COMBUSTION
AND
VENTILATION
Continued
Space: Includes the room in which you will install heater plus any adjoining rooms with doorless
passageways or ventilation grills between the rooms.
1. Determine the volume of the space (length x width x height).
Length x Width x Height =
___________________
cu. ft. (volume of space)
Example: Space size 20 ft. (length) x 16 ft. (width) x 8 ft. (ceiling height) = 2560 cu. ft. (volume of space)
If additional ventilation to adjoining room is supplied with grills or openings, add the volume of these
rooms to the total volume of the space.
2. Divide the space volume by 50 cubic feet to determine the maximum Btu/Hr the space can support.
____________ (volume of space) ÷ 50 cu. ft. = (Maximum Btu/Hr the space can support)
Example: 2560 cu. ft. (volume of space) ÷ 50 cu. ft. = 51.2 or 51,200 (maximum Btu/Hr the space
can support)
3. Add the Btu/Hr of all fuel burning appliances in the space.
Vent-free heater
Gas water heater*
Gas furnace
Vented gas heater
Gas fireplace logs
Other gas appliances*
Total
___________________ Btu/Hr
___________________ Btu/Hr
___________________ Btu/Hr
___________________ Btu/Hr
___________________ Btu/Hr
+ ___________________ Btu/Hr
= ___________________ Btu/Hr
Example: Gas water heater
Vent-free heater
Total
40,000
33,000
73,000
Btu/Hr
Btu/Hr
Btu/Hr
+
=
* Do not include direct-vent gas appliances. Direct-vent draws combustion air from the outdoors and
vents to the outdoors.
4. Compare the maximum Btu/Hr the space can support with the actual amount of Btu/Hr used.
_________________ Btu/Hr (maximum the space can support)
_________________ Btu/Hr (actual amount of Btu/Hr used)
Example: 51,200 Btu/Hr (maximum the space can support)
73,000 Btu/Hr (actual amount of Btu/Hr used)
The space in the above example is a confined space because the actual Btu/Hr used is more than the
maximum Btu/Hr the space can support. You must provide additional fresh air. Your options are as
follows:
A. Rework worksheet, adding the space of an adjoining room. If the extra space provides an unconfined
space, remove door to adjoining room or add ventilation grills between rooms. See Ventilation Air
From Inside Building, page 7.
B. Vent room directly to the outdoors. See Ventilation Air From Outdoors, page 7.
C. Install a lower Btu/Hr heater, if lower Btu/Hr size makes room unconfined.
If the actual Btu/Hr used is less than the maximum Btu/Hr the space can support, the space is an uncon-
fined space. You will need no additional fresh air ventilation.
6
103448
Download from Www.Somanuals.com. All Manuals Search And Download.
AIR FOR
COMBUSTION
AND
VENTILATION
Continued
WARNING
If the area in which the heater may be operated is smaller than that defined as an uncon-
fined space, provide adequate combustion and ventilation air by one of the methods
described in the National Fuel Gas Code, ANSI Z223.1, 1992, Section 5.3.
VENTILATION AIR
Ventilation Air From Inside Building
This fresh air would come from an adjoining unconfined space. When ventilating to an adjoining uncon-
fined space, you must provide two permanent openings: one within 12" of the ceiling and one within 12"
of the floor on the wall connecting the two spaces (see options 1 and 2, Figure 2). You can also remove
door into adjoining room (see option 3, Figure 2). Follow the National Fuel Gas Code NFPA 54/ANSI
Z223.1, Section 5.3, Air for Combustion and Ventilation for required size of ventilation grills or ducts.
WARNING
Rework worksheet, adding the space of the adjoining unconfined space. The combined
spaces must have enough fresh air to supply all appliances in both spaces.
12"
Ventilation
Ventilation Grills
Into Adjoining Room,
Option 2
Grills
Into Adjoining
Room,
Or
Remove
Door into
Adjoining
Room,
Option
3
Option 1
12"
Figure 2 - Ventilation Air from Inside Building
Ventilation Air From Outdoors
Provide extra fresh air by using ventilation grills or ducts. You must provide two permanent openings: one
within 12" of the ceiling and one within 12" of the floor. Connect these items directly to the outdoors or
spaces open to the outdoors. These spaces include attics and crawl spaces.
IMPORTANT: Do not provide openings for inlet or outlet air into attic if attic has a thermostat-controlled
power vent. Heated air entering the attic will activate the power vent.
Ventilated
Outlet
Attic
Air
Outlet
Air
To Attic
To
Crawl
Space
Inlet
Air
Ventilated
Inlet Air
Crawl Space
Figure 3 - Ventilation Air from Outdoors
7
103448
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLING
NOTICE
A qualified service person must install heater. Follow all local codes.
NOTICE
State or local codes may only allow operation of this appliance in a vented configuration.
Check your state or local codes.
WARNING
Make sure the remote selector switch is in the OFF position before installing heater.
WARNING
Before installing in a solid fuel burning fireplace, the chimney flue and firebox must be
cleaned of soot, creosote, ashes and loose paint by a qualified chimney cleaner. Creosote
will ignite if highly heated. Inspect chimney flue for damage. If damaged, operate heater
with flue damper closed.
WARNING
Seal any fresh air vents or ash clean-out doors located on floor or wall of fireplace. If not,
drafting may cause pilot outage or sooting. Use a heat-resistant sealant. Do not seal
chimney flue damper.
WARNING
Never install the heater
• in a bedroom or bathroom
• in a recreational vehicle
• where curtains, furniture, clothing, or other flammable objects are less than 36 inches
from the front, top, or sides of the heater
• in high traffic areas
• in windy or drafty areas
CAUTION
This heater creates warm air currents. These currents move heat to wall surfaces next to
heater. Installing heater next to vinyl or cloth wall coverings or operating heater where
impurities in the air (such as tobacco smoke) exist, may discolor walls.
IMPORTANT: Vent-free heaters add moisture to the air. Although this is beneficial, installing heater in
rooms without enough ventilation air may cause mildew to form from too much moisture. See Air for
Combustion and Ventilation, pages 5 through 7.
CHECK GAS TYPE
Use only propane (LP) gas. If your gas supply is not propane (LP) gas, do not install heater. Call dealer
where you bought heater for proper type heater.
8
103448
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION AND CLEARANCES
INSTALLING
Continued
WARNING
Maintain the minimum clearances. If you can, provide greater clearances from floor, ceiling,
and adjoining wall.
MINIMUM FIREPLACE CLEARANCE
TO COMBUSTIBLE MATERIALS
Log Size
Side Wall Ceiling
42"
Floor
18" 24" 30" 16"
5"
LOG SIZING REQUIREMENTS
Minimum Firebox Size
Log
Front
Width
Size Height Depth
18" 17"
24" 17"
30" 17"
14"
14"
14"
20"
26"
32"
Carefully follow the instructions below. This will ensure safe installation into a masonry or U.L. listed
manufactured fireplace or an AGA listed vent-free firebox approved for use with these gas log heaters.
Minimum Wall and Ceiling Clearances (see Figure 4)
A. Clearances from the side of the fireplace opening to any combustible wall should not be less than 16
inches.
B. Clearances from the top of the fireplace opening to the ceiling should not be less than 42 inches.
42"
16"
Figure 4 - Minimum Clearance to Wall and Ceiling
Minimum Non-Combustible Material Clearances
If Not Using Mantel
Note: If using a mantel, go to page 10. If not using a mantel, follow the information on this page.
You must have non-combustible material(s) above the fireplace opening. Non-combustible materials (such
as slate, marble, tile, etc.) must be at least 1/2 inch thick. With sheet metal, you must have non-combus-
tible material behind it. Non-combustible material must extend at least 8" up (for all models). If non-
combustible material is less than 12", you must install the fireplace hood accessory. See chart and Figure 5
on page 10 for minimum clearances.
Continued
9
103448
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLING
Non-Combustible
Material Distance (A)
Requirements for Safe Installation
Continued
12" or more
Non-combustible material OK.
Between 8" and 12"
Install fireplace hood accessory (GA6050 or GA6052, see Acces-
sories, page 30).
Less than 8"
Non-combustible material must be extended to at least 8". See
Between 8" and 12", above.
WARNING
Non-combustible material must extend 8" above the fireplace opening.
Heat Resistant
Material
(A)
Figure 5 - Heat Resistant Material (Slate, Marble, Tile, etc.) Above Fireplace
Minimum Non Combustible Material Clearances
If Using Mantel
You must have non-combustible material(s) above the fireplace opening. Non-combustible materials (such
as slate, marble, tile, etc.) must be at least 1/2 inch thick. With sheet metal, you must have non-combus-
tible material behind it. Non-combustible material must extend at least 8 inches up. If non-combustible
material is less than 12", you must install the fireplace hood accessory. Even if non-combustible material
is more than 12", you may need the hood accessory to deflect heat away from your mantel shelf. See chart
below and Figures 6 and 7 , page 11 for minimum clearances.
Non-Combustible
Material Distance (A)
Requirements for
Safe Installation
12" or more
Non-combustible material OK.
Between 8" and 12"
Install fireplace hood accessory (GA6050 or GA6052, see Acces-
sories, page 30).
Less than 8"
Non-combustible material must be extended to at least 8". See
Between 8" and 12", above.
WARNING
Non-combustible material must extend 8" above the fireplace opening.
10
103448
Download from Www.Somanuals.com. All Manuals Search And Download.
Mantel Clearances
INSTALLING
If you meet minimum clearance between mantel shelf and top of fireplace opening, a hood is not required
(see Figure 6).
Continued
Mantel Shelf
10"
Underside of
Mantel Shelf
8"
6"
2 1/2"
All minimum
distances are
in inches
Minimum Non-
Combustible
(A)
Material
12"
20"
241/2"
271/2" 30"
Top of Fireplace
Opening
Minimum Non-
Combustible
Material Height
Distances to
Underside of
Mantel
Figure 6 - Minimum Mantel Clearances Without Using Hood
If above minimum clearances are not met, you must have a hood. Follow minimum clearances shown in
Figure 7 when using hood.
Mantel Shelf
12"
Underside of
Mantel Shelf
10"
8"
6"
2 1/2"
All minimum
distances are
in inches
Minimum Non-
Combustible
Material
8"
12"
15"
18"
20"
Min.
Top of Fireplace
Opening
Hood
(GA6050, GA6052)
Distances to
Underside of
Mantel
Figure 7 - Minimum Mantel Clearances When Using Hood
If your installation does not meet the above minimum clearances, you must:
•
•
raise the mantel to an acceptable height, OR
remove the mantel.
Continued
11
103448
Download from Www.Somanuals.com. All Manuals Search And Download.
Floor Clearances
INSTALLING
A. If installing appliance on the floor level, you must maintain the minimum distance of 14" to combus-
tibles (see Figure 8).
Continued
Combustible
Material
14"
Min.
Non-Combustible
Material
Figure 8 - Minimum Fireplace Clearances If Installed at Floor Level
B. If combustible materials are less than 14" to the fireplace, you must install appliance at least 5" above
the combustible flooring (see Figure 9).
Hearth
Combustible
Material
5"
Min.
Figure 9 - Minimum Fireplace Clearances Above Combustible Flooring
INSTALLING HEATER BASE ASSEMBLY
WARNING
You must secure this heater to fireplace floor. If not, heater will move when you adjust
controls. Moving heater may cause a gas leak.
WARNING
If installing in a sunken fireplace, special care is needed. You must raise the fireplace floor
to allow access to heater control panel. This will insure adequate air flow and guard against
sooting. Raise fireplace floor with non-combustible material. Make sure material is secure.
CAUTION
Do not pick up heater base assembly by burners. This could damage heater. Only handle
base assembly by grates.
IMPORTANT: Make sure the heater burners are level. If heater is not level, heater will not work properly.
12
103448
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Items Needed
INSTALLING
• hardware package (provided with heater)
Continued
• approved flexible gas hose (not provided) (if allowed by local codes)
• sealant (resistant to propane (LP) gas, not provided)
• electric drill with 3/16" drill bit
Note: Install optional GHRCT Receiver and Hand Held Remote Control Kit (see Accessories, page 30)
before installing gas log heater. See installation instructions included with the kit.
1. Apply pipe joint sealant lightly to male threads of gas fitting. Connect approved flexible gas hose to
inlet side of gas control (see Figure 10).
2. Position heater base assembly in fireplace.
3. Mark screw locations through holes in front panel of base (see Figure 11). If installing in a brick-
bottom fireplace, mark screw locations in mortar joint of bricks.
4. Remove heater base from fireplace.
5. Drill holes at marked locations using 3/16" masonary drill bit.
6. Attach base to fireplace floor using masonry screws (in hardware package).
7. Connect to gas supply. See Connecting To Gas Supply, page 14.
Gas Control
Flexible Gas Hose (if
allowed by local codes)
Figure 10 - Attaching Flexible Gas Hose to Heater Gas Regulator
Masonry Screw
Masonry Screw
Figure 11 - Attaching Base to Fireplace Floor
Continued
13
103448
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTING TO GAS SUPPLY
INSTALLING
Continued
NOTICE
A qualified service person must connect heater to gas supply. Follow all local codes.
CAUTION
Never connect heater directly to the propane supply. This heater requires an external regulator
(not supplied). Install the external regulator between the heater and propane supply.
Installation Items Needed
Before installing heater, make sure you have the items listed below.
• external regulator (supplied by installer, see
Figure 12)
• piping (check local codes)
• sealant (resistant to LP gas)
• manual shutoff valve *
• test gauge connection *
• sediment trap
• tee joint
• pipe wrench
* An A.G.A. design-certified manual shutoff valve with 1/8" NPT tap is an acceptable alternative to test
gauge connection. Purchase the optional A.G.A. design-certified manual shutoff valve from your dealer.
See Accessories, page 30.
The installer must supply an external regulator. The external regulator will reduce incoming gas pressure.
You must reduce incoming gas pressure to between 11 and 14 inches of water. If you do not reduce
incoming gas pressure, heater regulator damage could occur. Install external regulator with the vent
pointing down as shown in Figure 12. Pointing the vent down protects it from freezing rain or sleet.
Propane
Supply Tank
External
Regulator
Vent Pointing
Down
Figure 12 - External Regulator With Vent Pointing Down
WARNING
Never connect heater to private (non-utility) gas wells. This gas is commonly known as
wellhead gas.
CAUTION
Use only new, black iron or steel pipe. Internally-tinned copper tubing may be used in
certain areas. Check your local codes. Use pipe of 1/2" diameter or greater to allow proper
gas volume to heater. If pipe is too small, undue loss of pressure will occur.
14
103448
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation must include a manual shutoff valve, union, and plugged 1/8" NPT tap. Locate NPT tap within
reach for test gauge hook up. NPT tap must be upstream from heater (see Figure 13).
INSTALLING
Continued
Apply pipe joint sealant lightly to male threads. This will prevent excess sealant from going into pipe.
Excess sealant in pipe could result in clogged heater valves.
CAUTION
Use pipe joint sealant that is resistant to liquid petroleum (LP) gas.
Install sediment trap in supply line as shown in Figure 13. Locate sediment trap where it is within reach
for cleaning. Locate sediment trap where trapped matter is not likely to freeze. A sediment trap traps
moisture and contaminants. This keeps them from going into heater controls. If sediment trap is not
installed or is installed wrong, heater may not run properly.
CAUTION
Avoid damage to gas control. Hold gas control with wrench when connecting it to gas
piping and/or fittings.
From
A.G.A. Design-Certified
Manual Shutoff Valve With
1/8" NPT Tap*
External Regulator
(11" W.C.** to
14" W.C.
Approved Flexible Gas
Hose (if allowed by local
codes)
Pressure)
Gas
Control
Tee Joint
Pipe
Nipple
3" Minimum
Cap
Sediment
Trap
Figure 13 - Gas Connection
* Purchase the optional A.G.A. design-certified manual shutoff valve from your dealer. See Accessories,
page 30.
** Minimum inlet pressure for purpose of input adjustment.
CHECKING GAS CONNECTIONS
WARNING
Test all gas piping and connections for leaks after installing or servicing. Correct all leaks
at once.
WARNING
Never use an open flame to check for a leak. Apply a mixture of liquid soap and water to all
joints. Bubbles forming show a leak. Correct all leaks at once.
CAUTION
Make sure external regulator has been installed between propane supply and heater. See
guidelines under Connecting to Gas Supply, page 14.
Continued
15
103448
Download from Www.Somanuals.com. All Manuals Search And Download.
Pressure Testing gas Supply Piping system
Test Pressures In Excess Of 1/2 PSIG
1. Disconnect heater and its individual manual shutoff valve from gas supply piping system. Pressures in
excess of 1/2 psig will damage heater regulator.
INSTALLING
Continued
2. Cap off open end of gas pipe where manual shutoff valve was connected.
3. Pressurize supply piping system by either using compressed air or
opening propane supply tank valve.
4. Check all joints of gas supply piping system. Apply mixture of liquid soap and water to gas joints.
Bubbles forming show a leak.
5. Correct all leaks at once.
6. Re-connect heater and manual shutoff valve to gas supply. Check re-connected fittings for leaks.
Test Pressures Equal To or Less Than 1/2 PSIG
1. Close manual shutoff valve (see Figure 14).
2. Pressurize supply piping system by either using compressed air or opening propane supply tank valve.
3. Check all joints from propane supply tank to manual shutoff valve (see Figure 15). Apply mixture of
liquid soap and water to gas joints. Bubbles forming show a leak.
4. Correct all leaks at once.
Pressure Testing Heater Gas Connections
1. Open manual shutoff valve (see Figure 14).
2. Open propane supply tank valve.
3. Make sure control knob of heater is in the OFF position.
4. Check all joints from manual shutoff valve to gas control (see Figure 14). Apply mixture of liquid soap
and water to gas joints. Bubbles forming show a leak.
5. Correct all leaks at once.
6. Light heater (see Operating Heater, pages 18 through 21). Check all other internal joints for leaks.
7. Turn off heater (see To Turn Off Gas to Appliance, page 20).
Open
Manual
Shutoff Valve
Closed
Figure 14 - Manual Shutoff Valve
Manual
Shutoff
Gas Control Location
Valve
Propane
Supply Tank
Figure 15 - Checking Gas Joints
16
103448
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLING LOGS
INSTALLING
Continued
WARNING
Failure to position the parts in accordance with these diagrams or failure to use only parts
specifically approved with this heater may result in property damage or personal injury.
Each log is marked with a number. These numbers will help you identify the log when installing. It is very
important to install these logs exactly as instructed. Do not modify logs. Only use logs supplied with
heater.
1. Place front logs (#1L and #1R) on top of the grate. Make sure the notches in the bottom of the logs fit
over the grate prongs (see Figure 16). Push back of logs flush with metal grate bar. Note: 18" model
has only one front log.
2. Rest bottom middle log (#2) behind metal posts on front burner. Make sure the grooves in the bottom
of the log fit over the grate. Bring the log forward next to the metal posts. The pegs on the log must be
on top (see Figure 17).
3. Slide the grooves in the back of the rear log (#3) against the rear grate prongs. Make sure the peg on
the log is on top (see Figure 18).
4. Place the top middle log (#4) on the bottom middle log (#2). Make sure the pegs of the bottom middle
log fit securely in the holes of the top middle log (see Figure 19).
Front Log (#1L)
Bottom Middle Log (#2)
Peg
Front Log (#1R)
Peg
Notch
Groove
Metal Post
Grate
Prongs
Groove
Metal Post
Metal Grate Bar
Grate
Figure 16 - Installing Front Logs
(#1L and #1R)
Figure 17 - Installing Bottom
Middle Log (#2)
Groo ve
in Back
of Log
Peg
Top Middle Log (#4)
Rear Log (#3)
Grate
Prong
Hole
Rear
Burner
Peg
Hole
Groove
in Back
of Log
Grate
Prong
Bottom
Middle Log
Peg
Continued
Figure 19 - Installing Top Log (#4)
Figure 18 - Installing Rear Log (#3)
17
103448
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Place the crossover log (#5) on the back log and the top middle log. Make sure the peg on the rear log
is in the hole in the bottom of the crossover log. The crossover log should fit in the cutout of the top
middle log (see Figure 20).
INSTALLING
Continued
Crossover Log (#4)
Hole
Cutout
Peg
Figure 20 - Installing Crossover Log (#5)
OPERATING
HEATER
FOR YOUR SAFETY READ BEFORE LIGHTING
WARNING
If you do not follow these instructions exactly, a fire or explosion may result causing
property damage, personal injury or loss of life.
A. This appliance has a pilot which must be lighted by hand. When lighting the pilot, follow these
instructions exactly.
B. BEFORE LIGHTING smell all around the appliance area for gas. Be sure to smell next to the floor
because some gas is heavier than air and will settle on the floor.
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electric switch; do not use any phone in your building.
• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s
instructions.
• If you cannot reach your gas supplier, call the fire department.
C. Use only your handto push inor turn the gascontrol knob. Never use tools. If the knob will not push
in or turn by hand, don’t try to repair it, call a qualified service technician or gas supplier. Force
or attempted repair may result in a fire or explosion.
D. Do not use this appliance if any part has been under water. Immediately call a qualified service
technician to inspect the appliance and to replace any part of the control system and any gas control
which has been under water.
18
103448
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING
HEATER
LIGHTING INSTRUCTIONS
WARNING
Continued
• If fireplace has glass doors, never operate this heater with glass doors closed. If you
operate heater with doors closed, heat buildup inside fireplace will cause glass to burst.
Also if fireplace opening has vents at the bottom, you must open the vents before operat-
ing heater.
• You must operate this heater with a fireplace screen in place. Make sure fireplace screen
is closed before running heater.
NOTICE
During initial operation of new heater, burning logs will give off a paper-burning smell. Orange
flame will also be present. Open damper or window to vent smell. This will only last a few hours.
Note: Homeowners generally prefer to operate their heater with the chimney damper closed. This
will put all the heat into the room. However there may be times you will desire the full flames of the
Hi heat setting but will find the heat output excessive. You can open the chimney damper (if you
have one) fully or partially to release some of the heat. WARNING: Damper handle will be hot if
heater has been running.
1. STOP! Read the safety information above.
2. Make sure manual shutoff valve is fully open.
3. Set remote selector switch in the OFF position.
WARNING
Burners will come on automatically within one minute when the remote selector switch is in
the ON position.
4. Press in and turn control knob clockwise
to the OFF position.
Flame
Control Knob
Adjustment
Knob
O
O
O
O
AUTO
OFF
ON
Ignitor Button
Selector Switch in OFF Position
Figure 21 - Control Knob and Ignitor Button Location
5. Wait five (5) minutes to clear out any gas. Then smell for gas, including near the floor. If you
smell gas, STOP! Follow “B” in the safety information above. If you don’t smell gas, go to the
next step.
6. Press in and turn control knob counterclockwise
knob for five (5) seconds (see above).
to the PILOT position. Press in control
Note: You may be running this heater for the first time after hooking up to gas supply. If so,
the control knob may need to be pressed in for 30 seconds or less. This will allow air to bleed
from the gas system.
7. With control knob pressed in, press and release ignitor button. This will light pilot. The pilot is
attached to the front burner. If needed, keep pressing ignitor button until pilot lights.
Note: If pilot does not stay lit, contact a qualified service person or gas supplier for repairs.
Until repairs are made, light pilot with match. To light pilot with match, see Manual Lighting
Procedure on page 20.
Continued
19
103448
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Keep control knob pressed in for 30 seconds after lighting pilot. After 30 seconds, release control
knob.
OPERATING
HEATER
•
If control knob does not pop out when released, contact a qualified service person or gas
Continued
supplier for repairs.
Note: If pilot goes out, repeat steps 4 through 8.
Ignitor Electrode
Pilot Burner
Figure 22 - Pilot
9. Slightly push in and turn control knob counterclockwise
to the ON position.
10.Wait one minute and switch remote selector switch to the ON position to light burner.
11.Set flame adjustment knob to any level between HI and LO.
CAUTION
Do not try to adjust heating levels by using the manual shutoff valve.
WARNING
Make sure the remote selector switch is in the OFF position when you are away from home
for long periods of time. Heater will come on automatically with remote selector switch in
the ON position.
TO TURN OFF GAS TO APPLIANCE
Shutting Off Heater
1. Turn control knob clockwise
to the OFF position.
2. Set remote selector switch in the OFF position to prevent draining battery.
Shutting Off Burners Only (pilot stays lit)
You may shut off the burners and keep the pilot lit by doing one of the following:
• Turn control knob clockwise
to the PILOT position.
• Use remote control manual OFF button.
• Set remote selector switch in the OFF position.
THERMOSTAT CONTROL OPERATION
The thermostat control setting on the remote control unit can be set to any comfort level between HI
and LO. The Burners will turn on and off automatically to maintain the comfort level you select.
The ideal comfort setting will vary by household depending upon the amount of space to be heated,
the output of the central heating system, etc.
MANUAL LIGHTING PROCEDURE
1. Follow steps 1 through 6 under Lighting Instructions, page 19.
2. Depress control knob and light pilot with match.
3. Keep control knob pressed in for 30 seconds after lighting pilot. After 30 seconds, release control
knob. Now follow step 9, above.
20
103448
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING
HEATER
OPTIONAL GHRCT HAND HELD REMOTE OPERATION
NOTICE
Continued
You must light the pilot before using the hand-held remote control unit. See Lighting
Instructions on page 19.
Control Knob in
On Position
Flame Adjustment Knob
O
O
O
ON
OFF
REMOTE
Remote Selector Switch in Remote Position
Figure 23 - Setting the Remote Selector Switch, Control Knob, and Flame Adjustment Knob
for Remote Operation
Note: The GHRCT receiver and hand-held remote control must be purchased separately (see
Accessories, page 30). Follow instructions included with the remote control.
1. After lighting, let pilot flame burn for about one minute. Turn control knob to ON position.
Adjust flame adjustment knob anywhere between HI and LO. Slide the remote selector switch to
the REMOTE position. The burners will come on. You can now turn the burners on and off with
the hand-held remote control unit.
IMPORTANT: Do not leave the remote selector switch in the REMOTE or ON position when the
pilot is not lit. This will drain the battery.
2. Select the MANUAL or AUTO button on the hand-held remote control unit.
• In MANUAL mode, turn burners on or off by pressing the ON or OFF buttons on the hand-
held remote control unit.
• In AUTO mode, the room temperature is controlled by the thermostat in the hand-held remote
control unit. To increase the room temperature, press the top arrow of the TEMP button. To
lower room the temperature, press the bottom arrow to the TEMP button. At higher settings
the heater will run more.
IMPORTANT: The hand-held remote control unit must be near the heater. Do not keep the
hand-held remote control unit too close the heater. The thermostat on the hand-held remote
control unit will heat up too quickly and turn the heater off.
3. Use the STATUS button on the hand-held remote control unit to see the operation mode being
used and the temperature setting selected. A red light will come on beside the operation mode
being used when the status button is pressed.
4. To turn the burners off when operating in the MANUAL mode, press the OFF button. If operat-
ing in the auto mode, press the manual button, then press the OFF button The pilot will remain
lit.
IMPORTANT: To turn the pilot off, manually turn the control knob on the heater to the OFF
position or set remote selector switch to OFF position.
Shows Temperature Setting
HI
Increases Room
Temperature
TEMP
Decreases Room
Allows Burners to be Turned
Temperature
On and Off with the Hand-
Held Remote Unit.
LO
MAN
ON
Turns Burners
On and Off
AUTO
OFF
The log heater will
Shows Current
Operation Mode
automatically cycle between
pilot and the heat setting that
has been selected.
STATUS
Figure 24 - GHRCT Thermostat Hand-Held Remote Control Unit Selections
21
103448
Download from Www.Somanuals.com. All Manuals Search And Download.
Check pilot flame pattern and burner flame patterns often.
INSPECTING
BURNERS
PILOT FLAME PATTERN
Figure 25 shows a correct pilot flame pattern. Figure 26 shows an incorrect pilot flame pattern. The
incorrect pilot flame is not touching the thermocouple. This will cause the thermocouple to cool. When the
thermocouple cools, the heater will shut down.
Thermocouple
Pilot Burner
Thermocouple
Pilot Burner
Figure 25 - Correct Pilot Flame Pattern
Figure 26 - Incorrect Pilot Flame Pattern
If pilot flame pattern is incorrect, as shown in Figure 26
• turn heater off (see To Turn Off Gas to Appliance, page 20)
• see Troubleshooting, pages 23 through 25
FRONT BURNER FLAME PATTERN
Figure 27 shows correct front burner flame pattern. Figure 28 shows incorrect front burner flame pattern.
The incorrect burner flame pattern shows yellow tipping at top of blue flame.
WARNING
If yellow tipping occurs, your heater could produce increased levels of carbon monoxide.
If front burner flame pattern shows yellow tipping, follow instructions at bottom of this
page. Yellow flame on rear burner is normal.
NOTICE
Do not mistake orange flames with yellow tipping. Dirt or other fine particles are burned by
heater, causing brief patches of orange flame.
CORRECT FLAME PATTERN AT HIGH POSITION
Figure 27 - Correct Front Burner Flame Pattern
Yellow
Tipping At
Top of
Blue
Flame
INCORRECT FLAME PATTERN AT HIGH POSITION
Figure 28 - Incorrect Front Burner Flame Pattern
If front burner flame pattern is incorrect, as shown in Figure 28
• turn heater off (see To Turn Off Gas to Appliance, page 20)
• see Troubleshooting, pages 23 through 25
22
103448
Download from Www.Somanuals.com. All Manuals Search And Download.
CLEANING AND
MAINTENANCE
WARNING
Turn off heater and let cool before cleaning.
CAUTION
You must keep control areas, burners, and circulating air passageways of heater clean.
Inspect these areas of heater before each use. Have heater inspected yearly by a qualified
service person. Heater may need more frequent cleaning due to excessive lint from carpet-
ing, bedding material, etc.
ODS/PILOT AND BURNERS
• Use a vacuum cleaner or small, soft bristled brush to clean.
LOGS
• If you remove logs for cleaning, refer to Installing Logs, pages 17 and 18, to properly replace logs.
• Replace log(s) if broken or chipped (dime-sized or larger).
TROUBLE-
SHOOTING
WARNING
Turn off and unplug heater and let cool before servicing. Only a qualified service person
should service and repair heater.
Note: All
troubleshooting items
are listed in order of
operation.
CAUTION
Never use a wire, needle, or similar object to clean ODS/pilot. This can damage ODS/pilot unit.
REMEDY
OBSERVED PROBLEM POSSIBLE CAUSE
1. Reconnect ignitor cable
When ignitor button is
pressed, there is no spark
at ODS/pilot
1. Ignitor electrode not connected
to ignitor cable
2. Ignitor cable pinched or wet
2. Free ignitor cable if pinched by any
metal or tubing. Keep ignitor cable dry
3. Tighten nut holding piezo ignitor to
base panel of log set. Nut is located
behind base panel.
3. Piezo ignitor nut is loose
4. Replace ignitor cable
5. Replace piezo ignitor
6. Replace ignitor
4. Broken ignitor cable
5. Bad piezo ignitor
6. Ignitor electrode positioned
wrong
7. Replace ignitor
7. Ignitor electrode broken
1. Turn on gas supply or open manual
shutoff valve
When ignitor button is
pressed, there is spark at
1. Gas supply turned off or
manual shutoff valve closed
2. Turn control knob to PILOT position
ODS/pilot but no ignition 2. Control knob not in PILOT
position
3. Press in control knob while in PILOT
position
3. Control knob not pressed in
while in PILOT position
4. Continue holding down control knob.
Repeat igniting operation until air is
removed
4. Air in gas lines when installed
5. Contact local propane (LP) gas company
6. Clean ODS/pilot (see Cleaning and
Maintenance, above) or replace ODS/
pilot assembly
5. Depleted gas supply
6. ODS/pilot is clogged
7. Replace gas control
7. Gas control setting is not correct
Continued
23
103448
Download from Www.Somanuals.com. All Manuals Search And Download.
OBSERVED PROBLEM
POSSIBLE CAUSE
REMEDY
TROUBLE-
SHOOTING
Continued
ODS/pilot lights but
flame goes out when
control knob is released
1. Control knob not fully pressed in
2. Control knob not pressed in long
enough
1. Press in control knob fully
2. After ODS/pilot lights, keep control
knob pressed in 30 seconds
3. Manual shutoff valve not fully
open
3. Fully open manual shut-off valve
4. Pilot flame not touching thermo-
couple, which allows thermo-
couple to cool, causing pilot
flame to go out. This problem
could be caused by one or both
of the following:
4. A) Contact local propane gas company
B) Clean ODS/pilot (see Cleaning and
Maintenance, page 23) or replace
ODS/pilot assembly
A) Low gas pressure
B) Dirty or partially clogged
ODS/pilot
5. Thermocouple connection loose
at control valve
5. Hand tighten until snug, then tighten
1/4 turn more
6. Thermocouple damaged
7. Gas control damaged
6. Replace thermocouple
7. Replace gas control
One or both burners do
not light after ODS/pilot
is lit
1. Inlet gas pressure is too low
2. Burner orifice(s) clogged
1. Contact local propane (LP) gas company
2. Clean burner(s) (see Cleaning and
Maintenance, page 23) or replace
burner orifice(s)
3. Mislocated crossover tube
4. Burner orifice(s) diameter is too
small
3. Contact qualified service person
4. Replace burner orifice(s)
5. Remote selector in OFF position
6. Wire disconnected from gas
control
5. Put remote selectorin ON position
6. See Wiring Diagram, page 26
Delayed ignition of one
or both burners
1. Manifold pressure is too low
2. Burner orifice(s) clogged
1. Contact local propane (LP) gas company
2. Clean burner(s) (see Cleaning and
Maintenance, page 23) or replace
burner orifice(s)
3. Mislocated crossover tube
3. Contact qualified service person
Burner backfiring during
combustion
1. Burner orifice is clogged or
damaged
1. Clean burner (see Cleaning and
Maintenance, page 23) or replace
burner orifice
2. Damaged burner
3. Gas control defective
2. Replace damaged burner
3. Replace gas control
Yellow flame in front
burner during burner
combustion
1. Not enough air
1. Check burner(s) for dirt and debris. If
found, clean burner(s) (see Cleaning
and Maintenance, page 23)
2. Gas control defective
2. Replace gas control
Slight smoke or odor
during initial operation
1. Residues from manufacturing
processes and logs curing
1. Problem will stop after a few hours of
operation
Moisture/condensation
noticed on windows
1. Not enough combustion/
ventilation air
1. Refer to Air for Combustion and
Ventilation requirements (page 5)
24
103448
Download from Www.Somanuals.com. All Manuals Search And Download.
OBSERVED PROBLEM POSSIBLE CAUSE
REMEDY
TROUBLE-
SHOOTING
Continued
Heater produces a
whistling noise when
burners are lit
1. Turning control knob to HI
position when burners are cold
2. Air in gas line
1. Turn control knob to LO position and
let warm up for a minute
2. Operate burners until air is removed
from line. Have gas line checked by
local natural gas company
3. Air passageways on heater
blocked
3. Observe minimum installation
clearances (see pages 9-12)
4. Dirty or partially clogged burner
orifice(s)
4. Clean burners (see Cleaning and
Maintenance, page 23) or replace
burner orifice(s)
WARNING
If you smell gas
• Shut off gas supply.
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any phone in your building.
• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s
instructions.
• If you cannot reach your gas supplier, call the fire department.
IMPORTANT: Operating heater where impurities in air exist may create odors. Cleaning supplies, paint,
paint remover, cigarette smoke, cements and glues, new carpet or textiles, etc., create fumes. These fumes
may mix with combustion air and create odors. These odors will disappear over time.
REMEDY
OBSERVED PROBLEM
POSSIBLE CAUSE
1. This is common with most heaters. If
noise is excessive, contact qualified
service person
Heater produces a click- 1. Metal expanding while heating
ing/ticking noise just after
burners are lit or shut off
or contracting while cooling
1. Open window to ventilate room. Stop
using odor causing products while
heater is running
Heater produces
unwanted odors
1. Heater burning vapors from
paint, hair spray, glues, cleaners,
chemicals, new carpet, etc. (See
IMPORTANT statement above)
2. Low fuel supply
2. Refill supply tank
3. Locate and correct all leaks (see
Checking Gas Connections, page 15)
3. Gas leak. See Warning state-
ment above
1. Open window and/or door for ventila-
tion
Heater shuts off in use
(ODS operates)
1. Not enough fresh air is available
2. Contact local propane (LP) gas company
3. Clean ODS/pilot (see Cleaning and
Maintenance, page 23)
2. Low line pressure
3. ODS/pilot is partially clogged
1. Locate and correct all leaks (see
Checking Gas Connections, page 15)
2. Replace gas control
Gas odor even when
control knob is in OFF
position
1. Gas leak. See Warning state-
ment above
2. Gas control defective
1. Take apart gas tubing and remove
foreign matter
Gas odor during
combustion
1. Foreign matter between control
valve and burner
2. Locate and correct all leaks (see
Checking Gas Connections, page 15)
2. Gas leak. See Warning state-
ment above
1. Move hand-held remote control unit
farther away from the heater
Log set cycles to pilot,
but room temperature
drops to a lower than
ideal level before log set
comes back on
1. Hand-held remote control unit
needs to be moved away from
heater
25
103448
Download from Www.Somanuals.com. All Manuals Search And Download.
18" Variable
16,000/26,000
Propane Only
Piezo
24" Variable
20,000/33,000
Propane Only
Piezo
30" Variable
21,500/36,000
Propane Only
Piezo
SPECIFICATIONS
Btu (Variable)
Type Gas
Ignition
Pressure Manifold
7.9" W.C.
7.9" W.C.
7.9" W.C.
Inlet Gas
Pressure (in. of water)
Maximum
14"
11"
14"
11"
14"
11"
Minimum*
* For purpose of input adjustment
Shipping Weight
32 lbs.
34 lbs.
36 lbs.
White
On
Off
Auto
WIRING
DIAGRAM
Switch
Red
TPTH
TH
Gas Control
TPTH
TP
Red
Thermopile
White
You may have further questions about installation, operation, or troubleshooting. If so, contact DESA
International’s Technical Service Department at 1-800-DESA LOG (1-800-337-2564).
TECHNICAL
SERVICE
When gas pressure is too low
• pilot will not stay lit
SERVICE HINTS
• burners will have delayed ignition
• heater will not produce specified heat
• propane (LP) gas supply may be low
When gas quality is bad
• pilot will not stay lit
• burners will produce flames and soot
• heater will backfire when lit
You may feel your gas pressure is too low or gas quality is bad. If so, contact your local propane (LP) gas
supplier.
26
103448
Download from Www.Somanuals.com. All Manuals Search And Download.
Note: Use only original replacement parts. This will protect your warranty coverage for parts replaced
under warranty.
REPLACEMENT
PARTS
Parts Under Warranty
Contact authorized dealers of this product. If they can’t supply original replacement part(s), call DESA
International’s Technical Service Department at 1-800-323-5190.
When calling DESA International, have ready
• your name
• your address
• model number of your heater
• how heater was malfunctioning
• type of gas used (propane or natural gas)
• purchase date
Usually, we will ask you to return the defective part to the factory.
Parts Not Under Warranty
Contact authorized dealers of this product. If they can’t supply original replacement part(s), call DESA
International’s Parts Department at 1-800-972-7879 for referral information.
When calling DESA International, have ready
• model number of your heater
• the replacement part number
27
103448
Download from Www.Somanuals.com. All Manuals Search And Download.
ILLUSTRATED PARTS
BREAKDOWN
Variable Control Model
VS18PR VS24PR VS30PR
4
5
3
2
1L
7
1R
6
8
25
10
13
10-2
9
10-1
8
6
11
8
12
27
6
26
29
24
28
13
14
16
22
18
21
20
15
17
19
23
28
103448
Download from Www.Somanuals.com. All Manuals Search And Download.
This list contains replaceable parts used in your heater. When ordering parts, follow the instructions
listed under Replacement Parts on page 30 of this manual.
PARTS LIST
Variable
Control Model
KEY
NO.
PART NUMBERS
VS18PR
VS24PR
VS30PR
DESCRIPTION
QTY.
1L
1R
2
3
4
5
6
7
8
103580-01
103580-02
103576-02
103577-01
103578-01
103579-01
M11084-26
103778-01
098249-01
103780-01
101330-05
101008-01
101007-01
100999-02
103984-02
098271-06
102445-01
103588-01
103782-01
M12461-26
103781-02
098264-02
103784-02
103784-01
103580-03
103580-02
103576-02
103577-03
103578-03
103579-01
M11084-26
103778-01
098249-01
103780-01
101330-06
101008-01
101007-01
100999-03
103984-03
098271-06
102445-01
103588-01
103782-01
M12461-26
103781-02
097264-02
103784-02
103784-01
Left Front Log (1L)
Right Front Log (1R)
Bottom Middle Log
Rear Log (#3)
Top Middle Log (#4)
Crossover Log
Screw
O.D.S. Pilot
Nut
Pilot Bracket
Front Burner Assembly
Crossover Burner Gasket
Crossover Burner
Rear Burner Assembly
Base Assembly and Decal
Ignitor Cable
Piezo Ignitor
Heat Shield
Valve Bracket
Screw
1
1
1
1
1
1
6
1
6
1
1
1
1
1
1
1
1
1
1
5
1
1
1
1
1
2
1
1
1
1
1
1
103580-04
103576-01
103577-02
103578-02
103579-02
M11084-26
103778-01
098249-01
103780-01
101330-04
101008-01
101007-01
100999-02
103984-01
098271-06
102445-01
103588-01
103782-01
M12461-26
103781-02
097264-02
103784-02
103784-01
9
10
10-1
10-2
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
Gas Control
Male Fitting
Flame Adjustment Knob
Control Knob
103587-01CK 103587-01CK 103587-01CK Switch Plate
M11084-26
103284-02
099387-09
101004-10
101004-10
103783-01
099998-01
M11084-26
103284-02
099387-09
101004-01
101004-02
103783-01
099998-01
M11084-26
103284-02
099387-09
101004-02
101004-06
103783-01
099998-01
Screw
Wiring Harness
Pilot Tube
Rear Burner Injector
Front Burner injector
Remote Burner Tube
Switch
PARTS AVAILABLE — NOT SHOWN
100563-01
103877-01
100565-01
100639-01
101137-02
101416-27
GA6060
100563-01
100563-01
103877-01
100565-01
100639-01
101137-02
101416-27
GA6060
Warning Plate
1
1
1
1
1
1
1
103877-01
100565-01
100639-01
101137-02
101416-27
GA6060
Lighting Instructions Plate
Warning Plate Fastener
Caution Decal
Hardware Kit
Information Video
Lava Rock
29
103448
Download from Www.Somanuals.com. All Manuals Search And Download.
Purchase these heater accessories from your local dealer. If they can not supply these accessories, call
DESA International’s Parts Department at 1-800-972-7879 for referral information. You can also write to
the address listed on the back page of this manual.
ACCESSORIES
MANUAL SHUTOFF
VALVE - GA5010
For all models. Manual shutoff valve with 1/8" NPT tap.
Fits 1/2" NPT pipe.
BLACK FIREPLACE
HOOD - GA6050
For all models. Helps deflect heat away from
mantel or wall above fireplace.
BRASS FIREPLACE
HOOD - GA6052
For all models. Helps deflect heat away from
mantel or wall above fireplace.
LAVA ROCK - GA6060
For all models. Order when additional rock is desired. (3 lb. bag)
HI
TEMP
MAN
LO
AU
T
RECEIVER AND HAND-HELD THERMOSTAT REMOTE
CONTROL KIT - GHRCT
O
ON
OFF
ST
A
TUS
For all models. Allows the gas log heater to be operated in a
manually or thermostatically controlled mode. You can turn the
gas log heater on and off without ever leaving the comfort of
your easy chair.
RECEIVER AND HAND-HELD REMOTE CONTROL KIT - GHRC
For all models. Allows the gas log heater to be turned on and off by using a
hand-held remote control.
WALL-MOUNT ON/OFF SWITCH - GWMS2
For all models. Allows the gas log heater to be turned on and off with
a wall switch.
WALL-MOUNT THERMOSTAT SWITCH - GWMS1
For all models. The desired comfort setting can be selected on the wall thermostat and the log heater will
automatically cycle from pilot to the heat setting selected.
30
103448
Download from Www.Somanuals.com. All Manuals Search And Download.
__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
NOTES
31
103448
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY INFORMATION
KEEP THIS WARRANTY
Model
Serial No.
Date Purchased
Always specify model and serial numbers when communicating with the factory.
We reserve the right to amend these specifications at any time without notice. The only warranty applicable is our standard
written warranty. We make no other warranty, expressed or implied.
LIMITED WARRANTY
VENT-FREE PROPANE GAS LOG HEATERS
DESA International warrants this product to be free from defects in materials and components for three (3) years and five
(5) years on stainless steel burners from the date of first purchase, provided that the product has been properly installed,
operated and maintained in accordance withall applicable instructions. There is nowarranty on the batteries. To make a claim
under this warranty the Bill of Sale or cancelled check must be presented.
This warranty is extended only to the original retail purchaser. This warranty covers the cost of part(s) required to restore this
heater to proper operating condition and an allowance for labor when provided by a DESA Authorized Service Center.
Warranty part(s) MUST be obtained through authorized dealers of this product and/or DESA International who will provide
original factory replacement parts. Failure to use original factory replacement parts voids this warranty. The heater MUST
be installed by a qualified installer in accordance with all local codes and instructions furnished with the unit.
This warranty does not apply to parts that are not in original condition because of normal wear and tear, or parts that fail or
become damaged as a result of misuse, accidents, lack of proper maintenance or defects caused by improper installation.
Travel, diagnostic cost, labor, transportation and any and all such other costs related to repairing a defective heater will be
the responsibility of the owner.
TO THE FULL EXTENT ALLOWED BY THE LAW OF THE JURISDICTION THAT GOVERNS THE SALE OF THE
PRODUCT; THIS EXPRESS WARRANTY EXCLUDES ANY AND ALL OTHER EXPRESSED WARRANTIES AND
LIMITS THE DURATION OF ANY AND ALL IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MER-
CHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE TO THREE (3) YEARS ON ALL COMPONENTS
AND FIVE (5) YEARS ON STAINLESS STEEL BURNERS FROM THE DATE OF FIRST PURCHASE; AND DESA
INTERNATIONAL’SLIABILITYISHEREBYLIMITEDTOTHEPURCHASEPRICEOFTHEPRODUCTANDDESA
INTERNATIONAL SHALL NOT BE LIABLE FOR ANY OTHER DAMAGES WHATSOEVER INCLUDING INDI-
RECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES.
Some states do not allow a limitation on how long an implied warranty lasts or an exclusion or limitation of incidental or
consequential damages, so the above limitation on implied warranties, or exclusion or limitation on damages may not apply
to you.
This warranty gives you specific legal rights, and you may also have other rights that vary from state to state.
For information about this warranty write:
2701 Industrial Drive
P.O. Box 90004
Bowling Green, KY 42102-9004
103448-01
Rev. B
05/97
Download from Www.Somanuals.com. All Manuals Search And Download.
|