Universal Remote Control Universal Remote UR4U MDVR CHD2 User Manual

STEP2 Press the [AUX] button and the [OK/SEL]  
button simultaneously for 3 seconds.The  
[AUX] Component LED will light for 30  
seconds.  
STEP1 Press the [TV] button and the [OK/SEL]  
button simultaneously for 3 seconds. The  
[TV] Component LED will light for 30 seconds.  
A. Quick Set-Up Method  
C. Auto-Search Method  
Introduction  
Button Functions  
1
4
STEP1 Turn on the Component you want to  
Operating Instructions  
For 4-Function  
Cable Remote Control  
STEP1 Turn on the device you want to program-  
This remote control is designed to operate all  
Motorola and Scientific Atlanta digital set top  
boxes (including HD and DVR), plus the  
majority of TVs, VCRs, DVDs and AUDIO  
equipment on the market as shown below.  
program (TV, VCR, DVD or AUX).  
to program your TV, turn the TV on.  
STEP2 Press the [VOL] button.  
STEP2 Press the [COMPONENT] button (TV,  
DVD or AUX) to be programmed and  
[OK/SEL] button simultaneously for 3  
seconds. The Component LED will light  
for 30 seconds indicating the unit is  
ready to be programmed.  
STEP2 Point the remote at the TV and press  
and hold the TV key for 3 seconds.  
While Holding the TV key, the TV LED  
will light off and on again. Begin to press  
the number keys, one at a time, starting  
with 1, then 2, 3…0 until the TV turns off.  
STEP3 Press the [COMPONENT] button you want  
to setup. Point the remote control toward  
the Component and enter the 3-digit code  
number assigned to your brand.  
STEP3 Press the [TV] button again.  
The Component LED will blink twice to  
confirm the programming.  
To return to original state:  
CABLE : Cable Converters TV : Televisions  
DVD : DVDs, TV/DVDs, VCRs and TV/VCRs  
AUX : Audio Receivers and DVRs, etc.  
*Note : If the 3-digit code number you just entered is  
the correct number, the Component will turn  
Off. If it did not turn Off, continue entering  
code numbers listed for that brand until the  
Component turns Off.  
If you wish to restore the CABLE channel control in  
TV mode, repeat the above steps but press [CBL]  
UR4U-MDVR-CHD2  
STEP3 Point the remote toward the  
Component and press the [CH] or  
[CH] button one step at a time or  
keep it pressed. The remote will emit a  
series of ON/OFF commands. Release  
the [CH] or [CH] button as soon as  
the Component turns Off.  
STEP3 Release the TV key to save the code.  
The TV LED will blink twice to confirm  
the code is stored.  
in STEP3  
.
Replacing Batteries  
Before you program or operate this remote  
control, you must first install two new AA Alkaline  
batteries.  
2
H. Programming Volume Control  
Repeat these steps for your DVD, Aux, etc.  
STEP4 Test functions. (Same as for 3-Digit Code  
Programming Method - Section B). If  
any of the functions do not work as they  
should, you need to find a new code.  
You can program the volume controls (Volume Up,  
Volume Down and Mute) from one Component to  
operate in another Component mode. Default volume  
control settings on the remote control are as follows:  
B. Pre-Programmed 3-Digit Code Method  
STEP1 Turn on the Component you want to  
STEP4 Test functions. (Same as for 3-Digit Code  
Programming Method - Section B). If any  
of the functions do not work as they  
should, repeat from STEP 3 using [CH]  
or [CH] buttons to find the correct code.  
STEP1 Remove the battery compartment cover  
program (TV, VCR, DVD or AUX) .  
STEP5 Once you have found the correct 3-digit  
code, save it by pressing the [AUX] button  
one more time. The Component LED light  
will blink twice to confirm the code was  
stored. Now when you press the AUX  
on the back of your remote control.  
CBL : TV  
T V : TV  
STEP2 Press the [COMPONENT] button (TV,  
DVD or AUX) to be programmed and  
[OK/SEL] button simultaneously for 3  
seconds. The Component LED will light  
for 30 seconds indicating the unit is  
ready to be programmed.  
DVD : TV  
AUX : AUX  
STEP2 Check battery polarity carefully, and  
install the batteries as shown in the  
illustration below.  
If you wish to operate the CBL volume control in  
CBL mode, use the following steps.  
STEP5 Save the code. (Same as for 3-Digit Code  
th  
button, all the buttons will work with that 4  
STEP1 Press the [CBL] button and the [OK/SEL]  
button simultaneously for 3 seconds. The  
[CBL] Component LED will light for 30  
seconds.  
STEP3 Replace the battery compartment cover.  
Programming Method - Section B).  
Component.  
Now, repeat the Auto-Search Method for those  
Components you could not program earlier with the  
Pre-Programmed Method.  
STEP3 Point the remote control toward the  
Component and enter the 3-digit code  
number assigned to your brand.  
F. Programming the System On/Off Button  
This allows you to program the System On/Off button  
so it can send up to four power On/Off commands  
with one button press.  
STEP2 Press the [VOL] button.  
STEP3 Press the [CBL] button.  
The Component LED will blink twice to  
confirm the programming.  
To return to original state:  
If you wish to restore the TV volume control in CBL  
mode, repeat the above steps but press [TV]  
D. Finding a Component Button’s  
Setup Code Number  
If you used the Auto-Search Method to program a  
Component, you may not know what the correct code  
number is. Here is a way for you to identify the code  
number, so you can record it for future reference.  
*Note : If the 3-digit code number you just  
entered is correct, the Component will  
turn Off. If it did not turn Off, continue  
entering code numbers listed for that  
brand until the Component turns Off.  
STEP1 Press the [CBL] button.  
STEP2 Press the [SYSTEM ON/OFF] button and the  
[OK/SEL] button simultaneously for 3  
seconds. The [CBL] Component LED will  
light for 30 seconds.  
STEP4 After you’ve entered the correct code  
number and the Component has turned  
Off, press the [POWER] button to turn  
the Component back On. Now it’s time  
to test the VOLUME and MUTE buttons  
for the TV (or PLAY and STOP buttons  
for VCR and DVD) to make sure they all  
work. If any of the functions do not  
work as they should, repeat from STEP  
3 using the next 3-digit code number  
listed for that brand.  
in STEP3  
.
STEP1 Press the [COMPONENT] button (TV, DVD or  
AUX) you want to verify and the [OK/SEL]  
button simultaneously for 3 seconds. The  
Component LED will light for 30 seconds.  
STEP3 Press the first [COMPONENT] button you  
want to store in the [SYSTEM ON/OFF]  
button and then the [POWER] button.  
Repeat this for other Components until you  
have stored all the desired power  
commands into the [SYSTEM ON/OFF]  
button.  
I. Programming a Favorite Channel  
See on-screen Guide Menu.  
Programming the Remote Control  
There are three ways you can program your remote control:  
5
J. Low Battery Warning  
STEP2 Press the [INFO] button and count the  
number of times the Component LED light  
blinks. This number indicates the first digit  
of the code, followed by the second and  
third, each separated by a one second  
pause when the LED will turn off.  
When the batteries are low and need to be  
replaced with fresh batteries, the Component LED  
lights will blink 2 times in sequence whenever a  
[POWER] button is pressed to turn on equipment.  
Operations  
3
Quick Set-Up Method  
*
STEP4 Press the [CH] button to save the power  
commands you stored. The [CBL] button  
will blink twice to confirm the commands  
have been saved.  
The Pre-Programmed 3-Digit Code Method  
*
DEFAULT STATUS:  
Component Default: CABLE  
Channel Default: CABLE channel +/- and  
numbers operate through the CABLE box.  
You have the option of controlling channel +/-  
and numbers through the TV, VCR or DVD.  
Refer to section G for programming steps.  
The Auto-Search Method  
*
STEP5 Once you have found the correct 3-  
digit code, save it by pressing the same  
[COMPONENT] button one more time.  
The Component LED light will blink  
twice to confirm that the code was  
successfully stored.  
K. Memory Lock System  
The Quick Set-Up Method is a unique new feature that enables the fastest and easiest set-up by using  
one-digit codes for up to 10 major brands for each component.  
The Pre-Programmed Code Method allows you to setup all the buttons at once by entering 3-digit code  
numbers that correspond to a particular Component’s manufacturer/brand, so it’s the fastest and  
easiest of the two methods. (Code Tables are on the backside of this Instruction Sheet.) The Auto-  
Search Method scans through all the codes in the remote control, one at a time.  
*Note : 10 blinks represents the number zero.  
This remote control is designed to retain  
programmed memory for 10 years even after  
batteries are removed from the remote control.  
G. Programming Channel Control  
Example : One blink, (pause), eight blinks, (pause) and  
three blinks, indicates code number 183.  
You can program the channel controls (Channel Up,  
Channel Down, Last and Numbers) from one  
Component to operate in another Component mode.  
Default channel control settings on the remote control  
are as follows:  
th  
E. AUX Function: Programming a 4  
Component  
L. Record Your Component Set-up Codes  
Now, program the rest of your Components by  
repeating STEPS 1-5.  
TV  
Set-up Code Number:  
Set-up Code Number:  
Set-up Code Number:  
IMPORTANT SETUP NOTES:  
Volume Default: CABLE volume +/- and mute  
operate through the TV. You have the option  
of controlling volume through the Cable box,  
VCR or DVD. Refer to section H for  
programming steps.  
You can take advantage of the AUX function to  
*Note : If the Pre-Programmed Method did  
not work, or if the Code Tables do not  
list your Component brand, use the  
Auto-Search Method as explained in  
Section C.  
DVD  
AUX  
th  
This pertains to all programming steps. When you are in setup mode in each component, a component  
LED will light up for 30 seconds. If you do not press a button within 30 seconds, the LED light will turn off  
and exit setup mode and you will need to start over.  
program a 4 Component such as a second TV, VCR,  
CBL : CBL  
T V : CBL  
DVD or Audio Component.  
Universal Remote Control, Inc.  
DVD : DVD  
AUX : AUX  
th  
STEP1 Turn on the 4 Component you want to  
If you wish to operate the TV channel control in TV  
mode, use the following steps.  
For additional information about your remote control,  
When programming a combo unit, program as a VCR or DVD first.  
OCE-0053A REV 20(08/17/11)  
program (TV, VCR, DVD or Audio).  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Technicolor Thomson Network Card SpeedTouch 121g User Manual
Telular Telephone SX6P User Manual
Toshiba Battery Charger B EP800 CHG QM R User Manual
TP Link Modem td w8961nd User Manual
Tripp Lite Computer Accessories U238 000 1 User Manual
Tripp Lite Switch PAM 1 User Manual
Victory Refrigeration Refrigerator RFS 2D S7 EW User Manual
Villaware Food Processor FPVLFPSL01 User Manual
VTech Telephone 912 User Manual
Wacom Graphics Tablet DTK 2400 User Manual