P
HONECELL® SX6P
CDMA2000 1X
• Fixed Wireless Phone
800 MHZ CDMA
1900 MHZ CDMA
USER MANUAL
08/18/04
Part Number 56031601
Download from Www.Somanuals.com. All Manuals Search And Download.
SX6P MENU STRUCTURE
Phonebook
View
Add
Edit
Erase
Menu
Call Log
Missed
Outgoing
Incoming
Erase Logs
Call Time
Air Time
Time/Alarm
Alarm
Time Format
Date Format
Clear Air Time
Ring/Alert
Ring Tone
Ring Volume
1 Min Alert
Service Alert
Alarm Tone
Phone Settings
Banner
My Phone Number
DTMF Length
Key Volume
Auto Send Delay
Freq. Dial Number
Language
Dial Tone Type
LCD Control
Data Settings
Baud Rate
Selftest Cycle
RX Data Mode
Tech Mode
Security
New Lock Code
Restrict
Voice Privacy
RUIM CHV1 (RUIM Models Only)
Auto Lock
User Defaults
SW Version Info
Hotline
Phonecell® SX6P CDMA
ii
User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
LIST OF COMPONENTS
Phonecell® SX6P
Desktop Phone
AC Power Cord
Power Supply
Spike Antenna
Before installing your Phonecell® SX6P, carefully remove the contents from the shipping carton
and check for evidence of shipping damage. If damage is found, contact your Authorized
Telular Distributor or shipping agent immediately.
SAFE OPERATION INSTRUCTIONS
IMPORTANT! Before installing or operating this product, read the SAFETY INFORMATION
section of this manual.
• Install unit indoors.
• Install unit on hard, flat surface for proper ventilation.
• Do not expose unit to rain or moisture.
• Do not place unit on or close to sources of heat
PLEASE SEE THE IMPORTANT NOTICES SECTION OF THIS MANUAL FOR
IMPORTANT INFORMATION ON USE, WARRANTY AND INDEMNIFICATION
IMPORTANT NOTICES
TERMS AND CONDITIONS FOR USE OF PHONECELL® PRODUCTS ("Product")
These Terms and Conditions are a legal contract between you and Telular Corporation for the title to and use of the Product.
BY RETAINING AND USING THE PRODUCT AFTER RECEIPT OF IT, YOU AGREE TO THE TERMS AND CONDITIONS
INCLUDING WARRANTY DISCLAIMERS, LIMITATIONS OF LIABILITY AND INDEMNIFICATION PROVISIONS BELOW. IF
YOU DO NOT AGREE TO THE TERMS AND CONDITIONS, DO NOT USE THE PRODUCT AND IMMEDIATELY RETURN
THE UNUSED PRODUCT FOR A COMPLETE REFUND. You agree to accept sole responsibility for any misuse of the Product
by you; and, in addition, any negligent or illegal act or omission of your or your agents, contractors, servants, employees, or
other users of the Product so long as the Product was obtained from you, in the use and operation of the Product.
INDEMNIFICATION OF TELULAR CORPORATION ("TELULAR")
YOU SHALL INDEMNIFY, DEFEND AND HOLD HARMLESS TELULAR FOR ANY OF THE COST, INCLUDING REASON-
ABLE ATTORNEYS' FEES, AND FROM CLAIMS ARISING OUT OF YOU, YOUR CLIENTS' OR OTHER THIRD PARTIES'
USE OR OPERATION OF THE PRODUCT: (i) FOR MISUSE OR IN A MANNER NOT CONTEMPLATED BY YOU AND
TELULAR OR INCONSISTENT WITH THE PROVISIONS OF THIS MANUAL; (ii) IN AN ILLEGAL MANNER OR AGAINST
PUBLIC POLICY; (iii) IN A MANNER SPECIFICALLY UNAUTHORIZED IN THIS MANUAL; (iv) IN A MANNER HARMFUL
OR DANGEROUS TO THIRD PARTIES; (v) FROM CLAIMS BY ANYONE RESPECTING PROBLEMS, ERRORS OR MIS-
TAKES OF THE PRODUCT; OR (vi) COMBINATION OF THE PRODUCT WITH MATERIAL, MODIFICATION OF THE
PRODUCT OR USE OF THE PRODUCT IN AN ENVIRONMENT NOT PROVIDED, OR PERMITTED, BY TELULAR IN WRIT-
ING. THE PARTIES SHALL GIVE EACH OTHER PROMPT NOTICE OF ANY SUCH COST OR CLAIMS AND COOPER-
ATE, EACH WITH THE OTHER, TO EFFECTUATE THIS INDEMNIFICATION, DEFENSE AND HOLD HARMLESS.
TELULAR CORPORATION
Corporate Headquarters
647 North Lakeview Parkway
Vernon Hills, Illinois 60061, USA
Technical Support
Tel: 847-247-9400 • Fax: 847-247-0021
Part Number 56031601
©2004 Telular Corporation, All Rights Reserved
Phonecell® SX6P CDMA
iii
User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
QUICK CONNECTION GUIDE .......................................................................................i
SX6P MENU STRUCTURE............................................................................................ii
LIST OF COMPONENTS..............................................................................................iii
SAFE OPERATION INSTRUCTIONS...........................................................................iii
IMPORTANT NOTICES.................................................................................................iii
TABLE OF CONTENTS ................................................................................................iv
SX6P SETUP..................................................................................................................1
RUIM Card Installation...............................................................................................1
Install Batteries ..........................................................................................................1
Battery Operation.......................................................................................................2
Location and Setup....................................................................................................2
Connect the Handset.................................................................................................2
Wall Mounting ............................................................................................................3
Connect the SX6P to AC Power................................................................................4
RUIM Usage ..............................................................................................................5
GETTING TO KNOW YOUR SX6..................................................................................6
Function Keys............................................................................................................6
LCD Screen Icons......................................................................................................7
Service Indication ......................................................................................................7
CALL FUNCTIONS ........................................................................................................8
Making Calls ..............................................................................................................8
Receiving Calls..........................................................................................................8
Ending Calls...............................................................................................................8
In-Call Functions........................................................................................................8
Voice Mail Access......................................................................................................9
Reading Text (SMS) Messages ................................................................................9
Sending a Text Message ..........................................................................................9
Delete All Text Messages...........................................................................................9
Message Lock..........................................................................................................10
Message Alert..........................................................................................................10
PHONE BOOK ............................................................................................................11
Speed Dial by Location............................................................................................11
Searching the Phone Book and Dialing a Phone Book Entry .................................11
Adding an Entry into the Phone Book......................................................................11
Edit a Phone Book Entry .........................................................................................12
Erase a Phone Book Entry ......................................................................................12
CALL LOGS.................................................................................................................12
View Missed Calls....................................................................................................12
View Outgoing Calls ................................................................................................13
View Incoming Calls ................................................................................................13
Erase All Call Logs ..................................................................................................13
View Last Call Time .................................................................................................13
View Total Air Time ..................................................................................................13
Clear Air Time ..........................................................................................................14
Phonecell® SX6P CDMA
Download from Www.Somanuals.com. All Manuals Search And Download.
iv
User Manual
TIME / ALARM ............................................................................................................14
Alarm........................................................................................................................14
Time Format.............................................................................................................14
Date Format.............................................................................................................14
RING / ALERT .............................................................................................................15
Ring Type.................................................................................................................15
Ring Tone.................................................................................................................15
Ring Volume ............................................................................................................15
One Minute Alert......................................................................................................15
Service Alert.............................................................................................................15
Alarm Tone...............................................................................................................15
PHONE SETTINGS......................................................................................................16
Banner .....................................................................................................................16
My Phone # (Display Only)......................................................................................16
DTMF Length...........................................................................................................16
Key Volume..............................................................................................................16
Auto Send Delay......................................................................................................16
Frequently Dialed Number.......................................................................................16
Change Language Displayed on LCD.....................................................................17
Dial Tone Type.........................................................................................................17
LCD Contrast...........................................................................................................17
DATA SETTINGS .........................................................................................................17
Baud Rate................................................................................................................18
Self Test Cycle.........................................................................................................18
RX Data Mode .........................................................................................................18
SECURITY SETTINGS.................................................................................................18
New Lock Code .......................................................................................................18
Restrict Calls............................................................................................................18
Voice Privacy ...........................................................................................................19
RUIM CHV1 (RUIM Models Only) ...........................................................................19
Auto Lock.................................................................................................................19
User Defaults ...........................................................................................................19
SW Version Information ..........................................................................................19
BONDING A SX6 TO A RUIM......................................................................................20
WINDOWS XP/WINDOWS 2000 SETUP ....................................................................21
SENDING/RECEIVING A PC FAX...............................................................................27
SENDING/RECEIVING 1X DATA.................................................................................28
SENDING/RECEIVING CIRCUIT SWITCHED DATA..................................................29
SX6P TROUBLESHOOTING.......................................................................................30
CONFORMANCE STATEMENTS................................................................................31
SAFETY INFORMATION .............................................................................................31
WARRANTY.................................................................................................................33
Phonecell® SX6P CDMA
Download from Www.Somanuals.com. All Manuals Search And Download.
v
User Manual
SX6P SETUP
RUIM Card Installation (RUIM Model Only)
Consult your service provider to determine if your unit is a RUIM model. If so, your SX6P will
only be able to make emergency calls until you install a RUIM card. It will not receive calls or
allow non-emergency outgoing calls. For an explanation of how to configure your RUIM once
your SX6P is set up, see RUIM Usage (page 6).
1. Remove the power supply if it has already been connected. The power supply must be
removed whenever a RUIM Card is removed or installed.
2. Remove the RUIM compartment cover. - see Figure 1.
3. Open the RUIM compartment holder.
4. Line up the RUIM card with the arrow on the RUIM card holder - see Figure 2.
5. Gently insert the RUIM card in the slot of the RUIM card holder.
6. Close the RUIM card holder.
NOTE: Do not force the RUIM card holder shut. Make sure the RUIM card is aligned properly
with the directional arrow on the holder.
7. Reattach the RUIM compartment cover, closing it with the separate cover screw provided.
RUIM Compartment Cover
Cover Screw
RUIM Card
Holder
RUIM Card
Figure 2 - RUIM card installation.
Figure 1 - RUIM compartment cover.
Install Batteries (Optional)
1. If necessary, remove the screw that may be holding the battery access door located on the
bottom of the unit - see Figure 3.
2. Press the battery access door tabs and remove the battery access door.
3. Install the Telular rechargeable battery pack into the battery pack area and connect wires.
4. Reinstall the battery access door using the screw - see Figure 4.
WARNING!
Do not use batteries other than the included Telular battery pack with the SX6P.
Using any other batteries may result in fire and/or other damage to the unit.
!
Battery Access Door
Battery Access
Door Tab And
Screw
Battery Pack Area
Figure 4 - Battery installation.
Figure 3 – Battery access door.
Phonecell® SX6P CDMA
1
User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Battery Operation
The SX6P will recharge its battery pack when connected to AC power. If AC power is interrupted,
the SX6P will continue to operate, using power from the battery.
Location and Setup
The SX6P comes with a standard spike antenna (TNC).
1. Attach and finger-tighten the antenna - see Figure 5. Do not over-tighten the antenna.
2. Select a location that is above ground and as close to windows (or exterior walls) as possible
to get the best signal - see Figure 6.
Figure 6 - SX6P location.
Figure 5 - Attach the antenna.
Connect the Handset
Before you can use the SX6P, you must connect the handset cable.
1. Connect the handset cable to the phone jack - see Figure 7.
2. Connect the handset cable to the handset - see Figure 7.
Phone jack
Handset cable
Handset
Figure 7 – SX6P handset connection.
Phonecell® SX6P CDMA
Download from Www.Somanuals.com. All Manuals Search And Download.
2
User Manual
Wall Mounting
1. Remove the mounting clip from the cradle and re-insert it with the tab pointing up - see
Figures 8 and 9.
Mounting Clip in
Cradle (tab up)
Remove
Mounting Clip
from the Cradle
(tab down)
Insert
Mounting
Clip into
the Cradle
(tab up)
Figure 9 – Handset mounting clip for wall-mount.
Figure 8 – Handset mounting clip assembly.
2. Mark two hole locations 83 mm (3-1/4 inches) vertically apart and drill two holes into the wall.
3. Install the screws (not supplied) into the wall, leaving a gap of approximately 3 mm
(1/8 inches) between the screw head and the wall.
4. Align the mounting holes with the screws and mount the SX6P onto the screws - see Figures
10 and 11.
Mounting
Holes
Figure 11 – Mount the SX6P onto the screws.
Figure 10 – SX6P mounting hooks.
Phonecell® SX6P CDMA
3
User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Connect the SX6P to AC Power
1 Connect the barrel connector of the power supply to the AC power input on the rear panel of
the SX6P - see Figure 12.
2. Plug the AC power cord into the power supply.
3. Plug the AC power cord into the wall socket.
4. Check the cellular signal strength and move the unit until the best signal possible is
achieved - see the Service Indication section of this manual.
Figure 12 – SX6P AC power connection.
AC Power
Barrel
Input
Connector
Wall Socket
AC Power Cord
Power Supply
Phonecell® SX6P CDMA
4
User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
RUIM Usage (RUIM Models Only)
Your service provider may require you to install a RUIM in your SX6P for it to operate normally (see
RUIM Card Installation (page 1) for details). Without a RUIM, these SX6P models will reject incom-
ing calls and allow only emergency outgoing calls.
Once a RUIM-using SX6P is operating normally, you can use it to set its RUIM to require a PIN, not
require a PIN, or change the existing PIN. See Security (page 20) for details.
Starting Your SX6P with a RUIM PIN
If your RUIM requires a PIN (Personal Identification Number, also called Cardholder Verification, or
CHV), follow these steps:
1. Power on your SX6P.
2. The SX6P will prompt you to enter your PIN. Enter the PIN for your RUIM, then press STO.
3. If you enter the wrong PIN, the SX6P will display an error message and ask you to reenter the
PIN.
4. Entering an incorrect PIN three times will cause the SX6P to block the inserted RUIM. If your
RUIM is blocked due to incorrect PIN use, it will prompt you to enter the unblocking code. You
must contact your service provider to obtain this unblocking code. Do not guess at the block
code or use your own PIN to attempt to unblock the SX6; entering wrong codes will eventually
cause the RUIM to become permanently blocked.
5. If you are unable to enter the correct PIN for the inserted RUIM, the SX6P will not operate
normally. It will reject incoming calls and permit only emergency outgoing calls.
Starting Your SX6P if Your RUIM Requires No PIN
Power on your SX6P. No additional steps are necessary.
Starting Your SX6P if it is Bonded to a RUIM
A SX6P may be bonded to a specific RUIM. Once it has, the SX6P will not operate normally with
any other RUIM installed in it. It will reject incoming calls and permit only emergency outgoing calls.
The same holds true for any other SX6P the bonded RUIM is installed into: it will not operate nor-
mally.
To start a bonded SX6P, power it on. No additional steps are necessary provided that the correct
RUIM is inserted into the SX6P.
If you want to bond a SX6P to an RUIM, contact your service provider.
Phonecell® SX6P CDMA
5
User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
GETTING TO KNOW YOUR SX6
Function Keys
Operation of the SX6P is accomplished through the function keys on the keypad of the unit
- see Figure 13.
LCD Screen - Displays
icons, information, and
menu options necessary to
operate the SX6P.
Clear - To clear an entry, erase
a digit during entry, or to go
back one menu level
Message - To access voicemail or to
send an SMS (text message)
Store - Used to store an entry
Menu - Used to access phone
settings and features.
Power - Used to power the unit
on and off.
Volume - Controls the speaker
volume level for the handset and
the speakerphone when the SX6P
is off-hook.
Redial - Dials the last number
called from the SX6P.
Flash - Allows answering of a call
waiting and connecting 3-way
calls. Also used to automatically
connect a call after dialing (skip
dial delay).
Star Key - Used as a back-
space key when entering
text.
Pound Key - Used as a
space key when entering
text.
Hold - Used to put the
active call on hold or to
reactivate an on-hold call.
Mute - Prevents the party on the
other end of a call from hearing any
sound from the SX6P.
Speakerphone - Engages the
speakerphone feature.
Figure 13 – SX6P keypad and function keys.
Phonecell® SX6P CDMA
6
User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
LCD Screen Icons
Icons displayed on the LCD screen indicate the features in use, the status of the phone, signal
strength and battery status - see Figure 14.
Speaker - Indicates speaker
phone is activated.
Off Hook - Indicates handset is
off the cradle.
Alarm - Indicates that
the alarm feature has
been set.
Message - Displays when
a new text or voicemail
message has been received.
Battery - Indicates the level of
battery power. The more bars,
the more power.
Roam - Indicates that
the unit is roaming.
Private - Indicates enhanced
voice privacy mode.
Received Signal
Strength - Indicates the
strength of the current
signal. The more bars,
the stronger the signal.
Clock - Displays the
current time.
Date - Displays the
current date and day
of the week.
Figure 14 – SX6P LCD screen icons.
Service Indication
Full Service
When powered on, the banner and current date and time will display. If service is available, the
antenna icon will display indicator bars. The number and height of the indicator bars increases as
the signal grows stronger (the more bars, the better the signal).
No Service
When no service is available, the antenna icon will not display indicator lines. Contact your serv-
ice provider to verify cellular service is activated. No calls can be made in this condition.
Phonecell® SX6P CDMA
7
User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
CALL FUNCTIONS
Making Calls
1. Pick up the handset or Press the SPEAKERPHONE key. The SX6P is now “off-hook.”
2. Listen for dial tone.
3. Dial the phone number. The dialed number will be displayed. The name will also be displayed
if it is stored in the phonebook.
Correct Dialing Errors
• To erase one digit, Press the CLR key once.
• To erase all digits, Press and hold down the CLR key until all digits are erased.
Redial the Last Telephone Number Dialed
1. Pick up the handset or Press the SPEAKERPHONE key. The SX6P is now “off-hook.”
2. Press the REDIAL key.
Receiving Calls
When there is an incoming call, the SX6P rings, an incoming call notification displays the call
type and Caller ID information (if available), and the LED blinks.
1. Pick up the handset or press the SPEAKERPHONE key. Press CLR to send the call directly
to voicemail.
2. Begin talking.
Receive a Call When Caller ID is Activated
The Caller ID feature displays the caller’s number when the SX6P rings. If the caller’s name and
number are stored together in the SX6P phonebook, the caller’s name and number will be dis-
played. Contact your service provider to activate this feature.
NOTE: If there are missed calls (calls not answered), “MISSED CALLS” will be displayed with
the number of calls missed. See the Call Logs section of this manual for more information.
Ending Calls
Hang up the phone by either placing the handset back onto the SX6P cradle or press the
SPEAKERPHONE key if using the speakerphone.
In-Call Functions
Mute a Call
1. While in a call, press the MUTE key. A notification will display in the upper right corner of the
LCD screen.
2. Press the MUTE key again to un-mute the microphone.
Call Waiting
The FLASH key is used to answer call waiting and to switch between calls. Contact your service
provider regarding the availability of the call waiting feature.
Place a Call on Hold
1. While in a call, press the HOLD key.
2. The display will change from Active to Held.
3. To reactivate the call, press the HOLD key again.
3-Way Calling
Contact your service provider regarding the availability of 3-way calling.
To perform a 3-way call:
1. Make the first call and wait until it connects.
2. After the first call is connected, dial the second number.
3. Press the FLASH key. This connects the second call and puts the first call on hold.
4. Wait for the second call to connect.
5. After you are connected to the second call, Press FLASH, which then connects the first
call and completes the 3-way call.
Phonecell® SX6P CDMA
8
User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjust Volume
1. While in a call, press the Volume keys to raise or lower the handset/speakerphone volume.
Voicemail Access
Contact your service provider regarding the availability of voicemail.
1. Press MSG.
2. Select 1: Voice Mail.
3. To listen to your voicemail, Select 1: Listen.
4. If you have deleted all your messages and the message indicator does not go away after an
hour, Press 2: Clr Msg Ind.
Reading Text (SMS) Messages
When you receive a new text message, the envelope icon will appear on the display. To access
messages:
1. Press MSG.
2. Select 2: Read Messages.
3. Use the arrow keys to select the desired message. Press STO to read it.
4. Once you have read the message, you can do the following:
1: Delete
2: Forward
3: Reply
[FLASH]: Call : dials the callback number in the message (if available)
Sending a Text Message
1. Press MSG.
2. Select 3: Create Message.
3. Select 1: New Message.
3. Select 2: Sent Messages
4. Enter the destination phone number.
5. Type the message using the keypad or a keyboard connected to the phone. Press STO when
done writing the message.
CLR: delete previous character
# and down arrow key: forward one character
* and up arrow key: backwards one character
MSG key: switch between uppercase, lowercase, and special characters
6. Enter the callback number that you want included with the message and Press STO. If you do
not want a callback number, Press STO.
7. Select the message priority as Normal or Urgent.
8. Select "Send & Save" if you want to send the message immediately and save a copy to the
Sent Messages folder.
Select "Send" if you want to send the message immediately without saving a copy.
Delete All Text Messages
1. Press MSG
2. Select 4: Delete Messages.
3. Use the up and down arrows to select whether you would like to delete all messages, then
Press STO.
NOTE: that individual messages can be deleted from the "Read Messages" option.
Phonecell® SX6P CDMA
9
User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Message Lock
Message lock password protects the Voice Mail menu. If the message lock is active and you
press the MSG key from the idle screen, the unit will prompt you for a password which is your
lock code (default is 0000).
1. Press MSG
2. Select 5: Message Options
3. Select 1: Message Lock
4. Select the desired option using the up/down arrows and Press STO to save.
Message Alert
Message Alert turns on and off the message alert tone. When off, the envelope icon will still be
displayed on the LCD but there is no alert tone.
1. Press MSG
2. Select 5: Message Options
3. Select 2: Message Alert
Select the desired option using the up/down arrows and Press STO to save.
Phonecell® SX6P CDMA
10
User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
PHONE BOOK
The SX6P can be programmed to store frequently called numbers via an electronic phone book.
The SX6P phone book can hold up to 99 entries.
Speed Dial by Location
A phone book entry can be speed dialed as follows: For entries 1-9, lift the handset and hold
down the location number until it dials.For entries 10-99, lift the handset, press the first digit and
then hold down the 2nd digit until it dials.
Searching the Phone Book and Dialing a Phone Book Entry
1. Start by pressing MENU
2. Select 1: Phone Book
3. Select 1: View
There are 3 options for conducting a search of the electronic phone book:
1. All - displays all entries from location 01 through 99
Use Up and down arrows to select the location and Press STO to select it.
2. Name - enter in the characters to search for and Press STO to search.
3. Location - enter the 2-digit location 01 through 99
To dial the selected entry, Press FLASH. Then pick up the handset if desired.
Adding an Entry into the Phone Book
1. Enter the phone number to be stored.
2. Press STO
3. Enter the name to be stored.
To enter a letter, Press the phone button with that letter, pressing it multiple times to cycle
through the letters available.
* key = backspace
# key = space
MSG key = shift between UPPERCASE and lowercase letters
4. When the unit displays, "Location auto=XX", Press STO or enter the desired location number.
NOTE: You can also add an entry to the phonebook through the phonebook add option.
Phonecell® SX6P CDMA
11
User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Edit a Phone Book Entry
1. Start by pressing MENU
2. Select 1: Phone Book
3. Select 3: Edit
There are 3 options for editing an entry:
1. All - displays all entries from location 01 through 99
Use Up and down arrows to select the location and Press STO to select it.
2. Name - enter in the characters to search for and Press STO to search.
3. Location - enter the 2-digit location 01 through 99
Erase a Phone Book Entry
1. Start by pressing MENU
2. Select 1: Phone Book
3. Select 4: Erase
There are 3 options for erasing an entry:
1. All - displays all entries from location 01 through 99
Use Up and down arrows to select the location and Press STO to select it.
2. Name - enter in the characters to search for and Press STO to search.
3. Location - enter the 2-digit location 01 through 99
CALL LOGS
The SX6P saves a log of the last 10 missed, outgoing, and incoming calls.
View Missed Calls
1. Start by pressing MENU
2. Select 2: Call Logs
3. Select 1: Missed
4. Use the up and down arrows to select the desired call and Press STO to view it.
To dial the selected entry, Press FLASH. Then pick up the handset if desired.
Phonecell® SX6P CDMA
12
User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
View Outgoing Calls
1. Start by pressing MENU
2. Select 2: Call Logs
3. Select 2: Outgoing
4. Use the up and down arrows to select the desired call and Press STO to view it.
To dial the selected entry, Press FLASH. Then pick up the handset if desired.
View Incoming Calls
1. Start by pressing MENU
2. Select 2: Call Logs
3. Select 3: Incoming
4. Use the up and down arrows to select the desired call and Press STO to view it.
To dial the selected entry, Press FLASH. Then pick up the handset if desired.
Erase All Call Logs
1. Start by pressing MENU
2. Select 2: Call Logs
3. Select 4: Erase logs
4. Press STO to erase the logs.
View Last Call Time
1. Start by pressing MENU
2. Select 2: Call Logs
3. Select 5: Call Time
This displays the duration of the previous call.
View Total Air Time
1. Start by pressing MENU
2. Select 2: Call Logs
3. Select 6: Air Time
This displays the total airtime that the phone has used since the last time it was cleared.
This is a calculation performed by the phone and may be different than the network's calculation.
Phonecell® SX6P CDMA
13
User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Clear Air Time
1. Start by pressing MENU
2. Select 2: Call Logs
3. Select 7: Clear Air Time
This option will clear the phone's memory of how much airtime has been used.
TIME / ALARM
The SX6P allows you to set an alarm clock that can be used one time or for every day.
Alarm
1. Start by pressing MENU
2. Select 3: Time / Alarm
3. Select 1: Alarm
Time Format
1. Start by pressing MENU
2. Select 3: Time / Alarm
3. Select 2: Time Format
This allows you to set the time format to be 12-hour or 24-hour format.
Note: The current time is set by the network and therefore cannot be set on the phone.
Date Format (option 3)
1. Start by pressing MENU
2. Select 3: Time / Alarm
3. Select 3: Date Format
This allows you to set the date format to be MM/DD or DD/MM.
Phonecell® SX6P CDMA
14
User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
RING / ALERT
The SX6P is capable of supporting multiple ring tones and types of alerts. To adjust these
settings, follow these instructions.
Ring Tone
1. Start by pressing MENU
2. Select 4: Ring/Alert
3. Select 1: Ring Tone
4. Use the up / down arrows to select the desired ring tone and Press STO to save.
Ring Volume
1. Start by pressing MENU
2. Select 4: Ring/Alert
3. Select 2: Ring Volume
4. Adjust with up / down arrows and Press STO to save.
One Minute Alert
The 1-minute alert beep alerts the user after every minute during a call.
1. Start by pressing MENU.
2. Select 4: Ring/Alert
3. Select 3: 1 Min Alert
4. Select ON or OFF and Press STO.
Service Alert
The Service Alert is an alert that sounds when entering or leaving a service area.
1. Start by pressing MENU.
2. Select 4: Ring / Alert
3. Select 4: Svc Alert
4. Select the desired option and Press STO to save.
Alarm Tone
The alarm tone is the sound that the alarm clock makes when it rings.
1. Start by pressing MENU.
2. Select 4: Ring / Alert
3. Select 5: Alarm Tone
4. Use the up / down arrows to select the desired ring tone and Press STO to save.
Phonecell® SX6P CDMA
15
User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
PHONE SETTINGS
Banner
The banner is the text on the screen shown when the phone is not in use. This can be used to
personalize your phone.
1. Start by pressing MENU.
2. Select 5: Phone Settings.
3. Select 1: Banner.
My Phone # (display only)
1. Start by pressing MENU.
2. Select 5: Phone Settings.
3. Select 2: My Phone #.
DTMF Length
Some applications may require changing the DTMF Length.
1. Start by pressing MENU.
2. Select 5: Phone Settings.
3. Select 3: DTMF Length.
4. Select the desired option and Press STO to save.
Key Volume
The key volume is the loudness of the tones generated when you press the phone's keys.
1. Start by pressing MENU.
2. Select 5: Phone Settings.
3. Select 4: Key Volume.
4. Select the desired setting and Press STO to save.
Auto Send Delay
The auto send delay is the amount of time the unit waits after you have stopped entering digits,
before dialing the number.
1. Start by pressing MENU.
2. Select 5: Phone Settings.
3. Select 5: Auto SND Delay.
4. Enter the desired setting and Press STO to save.
Frequently Dialed Number
If you dial a phone number twice and stay connected for at least 15 seconds, the unit will
remember that phone number and automatically send it without delay. This feature may be
enabled or disabled.
1. Start by pressing MENU.
2. Select 5: Phone Settings.
3. Select 6: Freq Dial Num.
4. Select the desired setting and Press STO to save.
Phonecell® SX6P CDMA
16
User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Change Language Displayed On LCD
The SX6P is capable of displaying multiple languages on the LCD screen.
1. Start by pressing MENU.
2. Select 5: Phone Settings.
3. Select 7: Language.
4. Select the desired setting and Press STO to save.
Dial Tone Type
1. Start by pressing MENU.
2. Select 5: Phone Settings.
3. Select 8: Dial Tone Type.
4. Select the desired setting and press STO to save.
1. North America (low 350 Hz, high 440 Hz)
2. Latin America (low 425 Hz, high 425 Hz)
3. East Europe (low 425 Hz, high 425 Hz)
4. China (low 450 Hz, high 450 Hz)
5. Nicaragua (low 450 Hz, high 450 Hz)
6. India (low 375.5 Hz, high 412.5 Hz)
LCD Contrast
1. Start by pressing MENU.
2. Select 5: Phone Settings.
3. Select 9: LCD Control
4. Select 1: LCD Contrast
5. Select the desired setting and Press STO to save.
Backlight (SX6P-300C series only)
1. Start by pressing MENU.
2. Select 5: Phone Settings.
3. Select 9: LCD Control
4. Select 2: Backlight
5. Select the desired setting and Press STO to save.
DATA SETTINGS
Baud Rate
Set the baud rate appropriate for the application. PC fax uses 19,200. For 1X or circuit switched
data, use 115,200. This is the communication speed between the computer and SX6; data trans-
fer rates will be much slower.
1. Start by pressing MENU.
2. Select 6: Data Settings.
3. Select 1: Baud Rate.
4. Select the desired baud rate and Press STO to save.
Phonecell® SX6P CDMA
17
User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Self Test Cycle
The unit will perform a periodic self test to ensure the proper operation of the phone. The default
setting is 180 minutes (3 hours).
1. Start by pressing MENU.
2. Select 6: Data Settings.
3. Select 2: Self Test cycle
4. Select between 0 and 65535 minutes and Press STO to save.
RX Data Mode
To receive data, you must set the RX data mode setting.
1. Start by pressing MENU.
2. Select 6: Data Settings.
3. Select 3: RX Data Mode.
4. Select the desired setting and Press STO to save.
SECURITY
New Lock Code
The lock code is a 4-digit password used to prevent unauthorized access to the phone. This
setting will allow you to change it. The default lock code is 0000.
1. Start by pressing MENU.
2. Select 7: Security.
3. Enter the current lock code.
4. Select 1: New Lock Code
Restrict Outgoing Calls
1. Start by pressing MENU.
2. Select 7: Security.
3. Enter the current lock code.
4. Select 2: Restrict.
5. Select the desired option and Press STO to save.
Voice Privacy
The cellular CDMA network offers inherent voice privacy. Check with your service provider for
the availability of enhanced voice privacy mode. If Enhanced is selected, the phone will request
Enhanced Voice Privacy and a "P" will be shown on the display if Enhanced Voice Privacy has
been granted by the network.
1. Start by pressing MENU.
2. Select 7: Security.
3. Enter the current lock code.
4. Select 3: Voice Privacy.
5. Select the desired option and Press STO to save.
Phonecell® SX6P CDMA
18
User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
RUIM CHV1 (RUIM Models Only)
If your SX6P requires an RUIM, this setting allows you to enable, disable or change its PIN, also
called the CHV1 (Card Holder Verification 1).
This menu option is not available if your SX6P is bonded to a RUIM.
1. Start by pressing MENU.
2. Select 7: Security.
3. Enter the current lock code.
4. Select 4: RUIM CHV1.
5. Select the desired option and Press STO.
6. Enter the SX6’s PIN.
7. If you are changing the PIN, enter the new PIN.
Auto Lock
The Auto Lock setting determines whether the phone will automatically lock. This would require
you to enter your lock code before being able to access the phone.
1. Start by pressing MENU.
2. Select 7: Security.
3. Enter the current lock code.
4. Select 4: Auto Lock. (5 on RUIM models)
5. Select the desired option and Press STO to save.
User Defaults
This setting is used to reset the SX6’s settings to the user default values.
1. Start by pressing MENU.
2. Select 7: Security.
3. Enter the current lock code.
4. Select 5: User Defaults. (6 on RUIM models)
5. Select RESET and Press STO to save.
Software Version Information
1. Start by pressing MENU.
2. Select 7: Security.
3. Enter the current lock code.
4. Select 6: SW Version Info. (7 on RUIM models)
Software Version Information
1. Start by pressing MENU.
2. Select 7: Security.
3. Enter the current lock code.
4. Select 7: Hot Line. (8 on RUIM models)
5. Select Enable (followed by phone number to dial automatically & STO) or Disable.
Phonecell® SX6P CDMA
19
User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
BONDING A SX6 TO A RUIM (SX6P-300C series only)
You can bond a SX6P to the RUIM inserted in it. Once a SX6P has been bonded to a RUIM, the
SX6P will not operate normally with any other RUIM installed in it. It will reject incoming calls and
permit only emergency outgoing calls. The same holds true for any other SX6P the bonded RUIM is
installed into: it will not operate normally.
Bonding a SX6P to a RUIM can only be done once. It cannot be undone by the user.
Before you can bond the SX6P to a RUIM, the RUIM must have a PIN enabled. See Security (page
20) for details.
1. Start by pressing MENU.
2. Select 6: Data Settings.
3. Select 4: Tech Mode.
4. Enter your Tech User Password. (Default: )
5. Select 6: Bonding PIN.
6. Enter the inserted RUIM’s PIN.
7. Cycle your SX6’s power. After the unit reboots, it will be bonded to the RUIM.
Phonecell® SX6P CDMA
20
User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
WINDOWS XP/WINDOWS 2000 SETUP (SX6P-300C series only)
To configure a Windows XP/Windows 2000 computer and SX6P to work together, follow these steps.
1. Connect your computer and the SX6P with a serial (RS-232) or USB cable, depending
on your phone model.
2. If you are using a USB cable, install the Telular USB drivers from the included CD.
3. Set the SX6’s baud rate (MENU > 6: Data Settings > 1: Baud Rate) to 115200 (19200
when faxing)
4. Install the SX6P as a new modem by opening the
Start -> Settings -> Control Panel -> Phone and Modem Options -> Modems Tab
5. Click on "Add…"
Phonecell® SX6 CDMA
21
User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Click on "Don't detect my modem, I will select it from a list".
7. Select "Standard 19200 bps Modem".
Phonecell® SX6P CDMA
22
User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Select the COM port to use (if a COM port does not display, all COM ports are currently
allocated).
9. Click Finish.
Phonecell® SX6P CDMA
23
User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
10.Configure the SX6P modem interface using the
Start -> Settings -> Control Panel -> Phone and Modem Options" -> Modems Tab
11. Select the 19200 bps Modem -> Click on Properties
12. Select the Modem tab.
13. Change the Maximum port speed to 115200 (19200 when faxing) and click OK.
Phonecell® SX6P CDMA
24
User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
14.Configure the USB or Serial port using the
Control Panel -> System ->Hardware -> Device Manager -> Ports Tab
15.Select the port used for the SX6P and right click on it. Select "Properties" from the
resulting pop-up menu.
Phonecell® SX6P CDMA
25
User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
16. Click on the Port Settings tab.
17. Use these settings:
Bits per second: 115200 (19200 when faxing)
Data bits: 8
Parity: None
Stop bits: 1
Flow control: Hardware
18.You may now proceed for transferring data and faxes by following the instructions in
this manual. See Sending/Receiving a PC Fax (page 31), Sending/Receiving 1X
Data (page 32) or Sending/Receiving Circuit Switched Data (page 33) for details.
Phonecell® SX6P CDMA
26
User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
SENDING/RECEIVING A PC FAX (SX6P-300C series only)
A PC can send and receive faxes using the SX6P. Your account with your service provider must
support circuit switched data transfer for the SX6P’s PC fax function to work. Note that you must
use a PC to send faxes with the SX6P; a fax machine connected directly to the SX6P will not
work.
Set the SX6P Baud Rate for PC Fax
1. Start by pressing MENU.
2. Select 6: Data Settings.
3. Select 1: Baud Rate.
4. Select 19200 and Press STO to save.
Set Your Computer’s Port and Modem Speeds for PC Fax
To send or receive faxes, you need to set the port and modem speeds your computer uses for
the SX6P to 19200 bps. See Windows XP/2000 Setup (pages 24 & 26).
To Send a PC Fax
Use your computer’s fax software to dial the receiving fax machine’s number. Whenever your
software asks you what modem to use, select the Standard 19200 Modem.
To Receive a PC Fax
First configure your SX6P to recognize incoming faxes.
1. Start by pressing MENU.
2. Select 6: Data Settings.
3. Select 3: RX Data Mode.
4. Select Fax Next Call or Fax Only and Press STO to save.
If Fax Only is selected, your SX6P will treat all incoming calls as if they were Class 2 faxes. To
return your SX6P to normal operation, choose Voice Always from the RX Data Mode Menu.
If Fax Next is selected, your SX6P will treat the next incoming call as a Class 2 fax, then
return to normal operation.
Once your SX6P is configured to recognize incoming faxes, use your computer’s fax software.
Whenever your software asks you what modem to use, select the Standard 19200 Modem.
Note: Taking the SX6P off hook while sending or receiving a fax will end the transfer.
Phonecell® SX6P CDMA
27
Technical Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
SENDING/RECEIVING 1X DATA (SX6P-300C series only)
Check with your service provider to see if your account supports 1X data transfer.
Set the SX6’s Baud Rate for 1X Data
1. Start by pressing MENU.
2. Select 6: Data Settings.
3. Select 1: Baud Rate.
4. Select 115200 and Press STO to save. This is the communication speed between the
computer and SX6P; data transfer rates will be much slower.
Set Your Computer’s Port and Modem Speeds for 1X Data
To send or receive circuit switched data, you need to set the port and modem speeds your
computer uses for the SX6P to 115200 bps. See Windows XP/2000 Setup (pages 24 & 26) for
details. This is the communication speed between the computer and SX6P; data transfer rates
will be much slower.
To Send or Receive 1X Data
Follow your service provider’s directions for sending and receiving 1X data. Whenever your
software asks you what modem to use, select the Standard 19200 Modem.
For Windows XP and Windows 2000, you can start by opening Control Panel > Network and
Dial Up Connections, then double-clicking on “Make New Connection” to start the Network
Connection Wizard.
Note: Taking the SX6P off hook during a data session will end the session.
Phonecell® SX6P CDMA
28
Technical Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
SENDING/RECEIVING CIRCUIT SWITCHED DATA (SX6P-300C series only)
Check with your service provider to see if your account supports circuit switched data transfer.
Set the SX6’s Baud Rate for Circuit Switched Data
1. Start by pressing MENU.
2. Select 6: Data Settings.
3. Select 1: Baud Rate.
4. Select 115200 and Press STO to save. This is the communication speed between the
computer and SX6P; data transfer rates will be much slower.
Set Your Computer’s Port and Modem Speeds for Circuit Switched Data
To send or receive circuit switched data, you need to set the port and modem speeds your
computer uses for the SX6P to 115200 bps. See Windows XP/2000 Setup (pages 24 & 26) for
details. This is the communication speed between the computer and SX6P; data transfer rates
will be much slower.
To Send Circuit Switched Data
Follow your service provider’s directions for sending circuit switched data. Whenever your
software asks you what modem to use, select the Standard 19200 Modem.
For Windows XP and Windows 2000, you can start by opening Control Panel > Network and
Dial Up Connections, then double-clicking on “Make New Connection” to start the Network
Connection Wizard.
To Receive Circuit Switched Data
First configure your SX6P to recognize incoming circuit switched data.
1. Start by pressing MENU.
2. Select 6: Data Settings.
3. Select 3: RX Data Mode.
4. Select Data Next Call or Data Only and Press STO to save.
If Data Only is selected, your SX6P will treat all incoming calls as if they were CSD. To
return your SX6P to normal operation, choose Voice Always from the RX Data Mode Menu.
If Data Next is selected, your SX6P will treat the next incoming call as CSD, then return to
normal operation.
Once your SX6P is configured to recognize incoming circuit switched data, follow your service
provider’s directions for receiving circuit switched data using your software. Whenever your soft-
ware asks you what modem to use, select the Standard 19200 Modem.
For Windows XP and Windows 2000, you can start by opening Control Panel > Network and
Dial Up Connections, then double-clicking on “Make New Connection” to start the Network
Connection Wizard.
Note: Taking the SX6P off hook during a data session will end the session.
Phonecell® SX6P CDMA
29
User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
SX6P TROUBLESHOOTING
Telephone Service is Not Working (Cannot make or receive calls)
· Make sure the SX6P powered on properly.
· Make sure any equipment that is externally connected to the SX6P is correctly connected.
· Test any externally connected equipment on a known system to verify operation.
· Make sure the antenna is properly connected.
· Make sure your wireless account is activated and service is established.
Unable to Receive Calls
· Is the handset on the cradle? If not, place the handset on the cradle and try again.
· Is the SX6P making a loud repetitive tone (ROH)? Then either speakerphone or the handset is off
hook. Hang-up and try again.
Unable to Make Calls
· If you do not hear standard dial tone when off hook, then your service has a problem. Contact your
service provider is you think this is the problem.
Unable to Send or Receive Circuit Switched Data (CSD) Calls
· Is your computer connected to the data port of the SX6? If not, connect the computer with an
appropriate data cable.
· Do you have CSD service on your wireless account? Contact your service provider for information.
· Is your computer configured properly to access data service with the SX6? Please reference the
data sections of this manual for proper setup.
Moisture or Ventilation Problems
· Is moisture forming on or around the SX6? Remove any moisture with a clean dry towel and move
the unit to a well ventilated area. Review the Temperature and Environment section of this manual
for more information.
No Power
· Is the power supply connected to the unit? Make sure power is available and that the power sup-
ply is properly connected to the SX6P.
· The power supply is connected but the unit still has no power. Make sure the circuit is functioning
to the power supply. Check breakers & contact your power company. Power may be off at location.
Phonecell® SX6P CDMA
30
User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
CONFORMANCE STATEMENTS
FCC Part 15 Class B Compliance
This Phonecell® SX6P model has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC rules. Changes or modifications not expressly
approved by Telular Corporation will void your authority to operate the equipment per FCC part
15 paragraph 15.21.These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment OFF and ON, the user
is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the antenna.
• Increase the separation between the equipment and the terminal.
• Connect the equipment into an outlet on a circuit different from that to which the terminal is
connected.
• Consult your Authorized Telular Distributor or an experienced radio/TV technician for help.
SAFETY INFORMATION
The Phonecell® SX6P functions as both a radio transmitter and receiver. When it is ON, the
SX6P receives and sends out radio frequency (RF) energy. The SX6P CDMA unit operates in
the frequency ranges of 824 MHz to 894 MHz and / or 1850 MHz to 1910 MHz. When you use
the SX6P, the cellular system handling your call controls the power level at which the unit transmits.
Exposure to RF (Radio Frequency) Energy
In 1991, the Institute of Electrical and Electronics Engineers (IEEE), and in 1992, the American
National Standards Institute (ANSI), updated the 1982 ANSI Standard for safety levels with
respect to human exposure to RF energy. After reviewing the available body of research, more
than 120 scientists, engineers and physicians from universities, government health agencies and
industry developed this updated Standard. In March, 1993, the U.S. Federal Communications
Commission (FCC) proposed the adoption of this updated Standard.
The design of your Telular Phonecell® SX6P complies with this updated Standard. Of course, if
you want to limit RF exposure even further than the updated ANSI Standard, you may choose to
control the duration of your calls and operate your phone in the most power-efficient manner.
Safe Operation Requirement
The Phonecell® SX6P must be either wall mounted or desk mounted and should not be operated
when any person is within 203 mm (8 inches) of the antenna.
Temperature and Environment
Operating Temperature: From -10°C to +50°C ; Up to 95% relative humidity (non-condensing).
Storage Temperature: From -40°C to +60°C; Up to 95% relative humidity (non-condensing).
Antenna Care and Replacement
Do not use the Phonecell® SX6P with a damaged antenna. If a damaged antenna comes into
contact with the skin, a minor burn may result. Have your antenna replaced by a qualified techni-
cian immediately. Use only a manufacturer-approved antenna. Unauthorized antennas, modifica-
tions, or attachments could damage the Phonecell® SX6P.
WARNING!
DO NOT PICK UP OR CARRY THE PHONE BY ITS ANTENNA. THIS
ACTION MAY CAUSE SERIOUS DAMAGE.
!
Phonecell® SX6P CDMA
31
User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Driving
Check the laws and regulations on the use of cellular products in the areas where you drive.
Some jurisdictions prohibit your using a cellular device while driving a vehicle. Even if your juris-
diction does not have such a law, we strongly suggest that, for safety reasons, the driver use
extreme caution when operating the cellular device while the vehicle is in motion. Always obey
the law.
Electronic Devices
Most modern electronic equipment is shielded from RF energy. However, RF energy from cellular
devices may affect inadequately shielded electronic equipment.
RF energy may affect improperly installed or inadequately shielded electronic operating and
entertainment systems in motor vehicles. Check with the manufacturer or its representative to
determine if these systems are adequately shielded from external RF energy. You should also
check with the manufacturer of any equipment that has been added to your vehicle.
Consult the manufacturer of any personal medical devices (such as pacemakers, hearing aids,
etc.) to determine if they are adequately shielded from external RF energy.
Turn your Phonecell® SX6P OFF in health care facilities when any regulations posted in the
areas instruct you to do so. Hospitals or health care facilities may be using equipment that could
be sensitive to external RF energy.
Aircraft
Turn OFF your Phonecell® SX6P before boarding any aircraft.
• Use it on the ground only with crew permission.
• Do not use it in the air.
To prevent possible interference with aircraft systems, U.S. Federal Aviation Administration (FAA)
regulations require you to have permission from a crew member to use your cellular phone (or
any other cellular product) while the plane is on the ground. To prevent interference with aircraft
systems, FCC regulations prohibit using your cellular device while the plane is in the air.
Children
Do not allow children to play with your Phonecell® SX6P to prevent damage to the unit.
Blasting Areas
Construction crews often use remote control RF devices to set off explosives. Therefore, to avoid
interfering with blasting operations, turn your Phonecell® SX6P OFF when in a "blasting area" or
in areas posted: "Turn off two-way radio."
Potentially Explosive Atmospheres
Turn your Phonecell® SX6P OFF when in any area with a potentially explosive atmosphere. It is
rare, but your Phonecell® SX6P or its accessories could generate sparks. Sparks in such areas
could cause an explosion or fire resulting in bodily injury or even death.
Areas with a potentially explosive atmosphere are often, but not always, clearly marked. They
include fueling areas such as gas stations; below deck on boats; fuel or chemical transfer or
storage facilities; areas where the air contains chemicals or particles, such as grain, dust, or
metal powders; and any other area where you would normally be advised to turn off your vehicle
engine.
Do not transport or store flammable gas, liquid or explosives in the area of your Phonecell®
SX6P or accessories.
Vehicles using liquefied petroleum gas (such as propane or butane) must comply with the
National Fire Protection Standard (FPA-58). For a copy of this standard, contact the National Fire
Protection Association, One Batterymarch Park, Quincy, MA 02269, Attn: Publications Sales
Division.
Phonecell® SX6P CDMA
32
User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY
I. WHAT THIS WARRANTY COVERS AND FOR HOW LONG:
TELULAR CORPORATION ('Telular") warrants to a distributor Buyer, or to a customer only if the
customer is a Buyer directly from Telular, that the Products (including accessories) shall comply
with the applicable Specifications and shall be free from defects in material and workmanship
under normal use and service for a period of fifteen (15) months from date of shipment from
Telular. Telular, at its option, shall at no charge either repair, replace or refund the purchase price
of the Product during the warranty period, provided it is returned by Buyer in accordance with the
terms of this warranty to the Telular designated repair center. Repair or replacement, at Telular's
option, may include the replacement of parts, boards or Products with functionally equivalent
reconditioned items. Repaired and replacement items are warranted for the balance of the origi-
nal warranty period. All replaced items shall become the property of Telular. SUCH ACTION ON
THE PART OF TELULAR SHALL BE THE FULL EXTENT OF TELULAR'S LIABILITY HERE-
UNDER, AND BUYERS EXCLUSIVE REMEDY. Buyer shall be responsible for all costs and
expenses incurred by Buyer including without limitation any handling, labor or transportation
charges. OTHER THAN AFORESAID, THIS EXPRESS WARRANTY IS EXTENDED BY TELU-
LAR TO BUYER ONLY AND NOT TO BUYER'S CUSTOMERS OR USERS OF BUYER'S
PRODUCTS.
II. HOW TO OBTAIN WARRANTY SERVICE
Product covered under this warranty shall only be accepted from and returned to Buyer's desig-
nated repair center. Buyer's dealers, distributors, agents, and end users cannot submit items to
Telular under this warranty. To receive warranty service an RMA number must first be obtained
from Telular Technical Support. The defective or non-compliant Product should be sent by Buyer
freight pre-paid to: Telular Corporation, 647 North Lakeview Parkway, Vernon Hills, IL 60061,
USA or other designated location. The product must be packaged in the original carton and
packing material or an equivalent package and must have the assigned RMA number clearly
marked on the carton. Returned Product received without an RMA number will be returned to the
sender.
III. WARRANTY CONDITIONS:
This is the complete warranty for the Products manufactured by Telular and sold to Buyer. Telular
assumes no obligation or liability for additions or modifications to this warranty unless made in
writing and signed by an officer of Telular. Unless made in separate written agreement between
Telular and Buyer, Telular does not warrant the installation, field maintenance or service of the
Products or parts.
TELULAR CANNOT BE RESPONSIBLE IN ANY WAY FOR ANY ANCILLARY EQUIPMENT
NOT FURNISHED BY TELULAR WHICH IS ATTACHED TO OR USED IN CONNECTION WITH
THE PRODUCTS OR FOR OPERATION OF THE PRODUCTS WITH ANY ANCILLARY EQUIP-
MENT AND ALL SUCH EQUIPMENT IS EXPRESSLY EXCLUDED FROM THIS WARRANTY.
FURTHERMORE, TELULAR CANNOT BE RESPONSIBLE FOR ANY DAMAGE TO THE
PRODUCTS RESULTING FROM THE USE OF ANCILLARY EQUIPMENT NOT FURNISHED
BY TELULAR FOR USE WITH THE PRODUCTS.
WHEN THE PRODUCT IS USED IN CONJUNCTION WITH ANCILLARY OR PERIPHERAL
EQUIPMENT NOT MANUFACTURED BY TELULAR, TELULAR DOES NOT WARRANT THE
OPERATION OF THE PRODUCT/PERIPHERAL COMBINATION, AND TELULAR SHALL
HONOR NO WARRANTY CLAIM WHERE THE PRODUCT IS USED IN SUCH A COMBINA-
TION AND IT IS DETERMINED BY TELULAR THAT THERE IS NO FAULT WITH THE PROD-
UCT. TELULAR DISCLAIMS LIABILITY FOR RANGE, COVERAGE, AVAILABILITY, OR
OPERATION OF THE CELLULAR SYSTEM WHICH IS PROVIDED BY THE CARRIER.
IV. WHAT THIS WARRANTY DOES NOT COVER:
(a) Subsequent upgrades and enhancements to the Product. (b) Defects, non-compliance or
damage resulting from use of the Product in other than its normal and customary manner or
environment. (c) Defects, noncompliance or damage from misuse, lightening, accident or neg-
lect. (d) Defects, noncompliance or damage from improper testing, operation, maintenance,
installation, adjustment, or any alteration or modification of any kind. (e) Product disassembled or
repaired in such a manner as to adversely affect performance or prevent adequate inspection
and testing to verify any warranty claim. (f) Product which has had the serial number removed or
made illegible. (g) Defects, non-compliance or damage due to spills of food or liquid. (h) All plas-
tic surfaces and all other externally exposed parts that are scratched or damaged due to cus-
Phonecell® SX6P CDMA
33
User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
tomer normal use. (i) Costs and expenses, including without limitation handling, labor and trans-
portation, incurred in returning Product for warranty service to Telular's Repair Center. (j) Repair,
programming or servicing by someone other than Telular.
V. GENERAL PROVISIONS:
THIS WARRANTY IS GIVEN IN LIEU OF ALL OTHER EXPRESS OR STATUTORY WAR-
RANTIES. IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION IMPLIED WAR-
RANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, TITLE,
INFRINGEMENT, DELIVERY, NEGLIGENCE AND PERSONAL INJURY, ARE DISCLAIMED.
FURTHER, AS THE CELLULAR CARRIER IS NOT CONTROLLED BY TELULAR, NO WAR-
RANTY IS MADE AS TO COVERAGE, AVAILABILITY OR GRADE OF SERVICE PROVIDED
BY THE CELLULAR CARRIER. IN NO EVENT SHALL TELULAR BE LIABLE FOR DAM-
AGES IN EXCESS OF THE PURCHASE PRICE OF THE PRODUCT, FOR ANY LOSS OF
USE, LOSS OF TIME, INCONVENIENCE, COMMERCIAL LOSS, LOST PROFITS OR SAV-
INGS OR OTHER INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES ARISING OUT
OF THE USE OR INABILITY TO USE SUCH PRODUCT TO THE FULL EXTENT SUCH MAY
BE DISCLAIMED BY LAW. SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR
LIMITATIONS OF INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LIMITATION ON HOW
LONG AN IMPLIED WARRANTY LASTS.
VI. SOFTWARE PROVISIONS:
Laws in the United States and other countries preserve for Telular certain exclusive rights for
copyrighted Telular software such as the exclusive rights to reproduce in copies and distribute
copies of such Telular software. Telular software may be copied into, used in and redistributed
with only the Product associated with such Telular software. No other use, including without limi-
tation, disassembly of such Telular software or exercise of exclusive rights in such Telular soft-
ware is permitted and Telular reserves all rights not expressly granted in this Limited Commercial
Warranty.
Patents:
Telular Corporation products are protected and manufactured under one or more of the following
U.S. patents and related international patents and patents pending relating thereto: 4,658,096;
4,737,975; 4,775,997; 4,868,519; 4,922,517; 5,134,651; 5,361,297; 5,469,494; 5,046,085;
5,715,296.
Trademarks:
Telular Corporation owns the following registered trademarks: TELULAR and design, TELULAR,
CELJACK, MAXJACK, TELCEL, HEXAGON LOGO, PHONECELL, CELSERV, TELGUARD,
CPX, and AXCELL.
“Licensed by QUALCOMM Incorporated under one or more of the following Patents:
4,901,307
5,506,865
5,267,261
5,600,754
5,490,165
5,109,390
5,544,196
5,414,796
5,056,109
5,511,073
5,267,262
5,657,420
5,504,773
5,228,054
5,568,483
5,416,797”
5,101,501
5,535,239
5,337,338
5,778,338
5,710,784
5,659,569
Phonecell® SX6P CDMA
34
User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Phonecell® SX6 CDMA
35
User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Phonecell® SX6 CDMA
36
User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Phonecell® SX6 CDMA
37
User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
647 North Lakeview Parkway
Vernon Hills, Illinois 60061, USA
Tel: 847-247-9400 • Fax: 847-247-0021
E-mail: [email protected]
©2004 Telular Corporation, all rights reserved.
Part Number 56031601
Download from Www.Somanuals.com. All Manuals Search And Download.
|