A
UNITED STATES STOVE COMPANY
S
C
U S
“Keeping North America Warm Since 1869”
P
Models: 5824
Owner’s Manual
Please read this entire manual before installation and use of this appliance. Failure to follow
these instructions could result in property damage, bodily injury, or even death.
Contact your local building or fire officials about restrictions and installation inspection
requirements in your area.
Save these instructions.
UNITED STATES STOVE COMPANY • 227 INDUSTRIAL PARK ROAD • SOUTH PITTSBURG, TENNESSEE 37380 • WWW.USSTOVE.COM
Part No.: 851740 rev D
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Precautions
IMPORTANT: Read this entire manual before installing
Allow the stove to cool before performing any
and operating this product. Failure to do so may
result in property damage, bodily injury, or even death.
Proper installation of this stove is crucial for safe and
efficient operation.
maintenance or cleaning. Ashes must be disposed
in a metal container with a tight fitting lid. The closed
container of ashes should be placed on a non-
combustible surface or on the ground, well away from
all combustible materials, pending final disposal.
Install vent at clearances specified by the vent
manufacturer.
The exhaust system should be checked monthly during
the burning season for any build-up of soot or creosote.
Do not connect the pellet vent to a vent serving any
other appliance or stove.
Do not touch the hot surfaces of the stove. Educate all
children on the dangers of a high-temperature stove.
Young children should be supervised when they are
in the same room as the stove.
Do not install a flue damper in the exhaust venting
system of this unit.
Use of outside air is not required for this unit.
The hopper and stove top will be hot during operation;
therefore, you should always use some type of hand
protection when refueling your stove.
Contact your local building officials to obtain a
permit and information on any additional installation
restrictions or inspection requirements in your area.
A power surge protector is required. This unit
must be plugged into a 110 - 120V, 60 Hz grounded
electrical outlet. Do not use an adapter plug or sever
the grounding plug. Do not route the electrical cord
underneath, in front of, or over the heater. Do not
route the cord in foot traffic areas or pinch the cord
under furniture.
Do not throw this manual away. This manual has
important operating and maintenance instructions
that you will need at a later time. Always follow the
instructions in this manual.
This heater is designed and approved for premium
hardwood pellet fuel only. Any other type of fuel burned
in this heater will void the warranty and safety listing.
The heater will not operate during a power outage. If a
power outage does occur, check the heater for smoke
spillage and open a window if any smoke spills into
the room.
Never use gasoline, gasoline-type lantern fuel,
kerosene, charcoal lighter fluid, or similar liquids to
start or ’freshen up’ a fire in this stove. Keep all such
liquids well away from the stove while it is in use.
The viewing door must be closed and sealed during
operation.
Aworking smoke detector must be installed in the same
room as this product.
Never block free airflow through the open vents of
the unit.
Do not unplug the stove if you suspect a malfunction.
Keep foreign objects out of the hopper.
Turn the stove OFF by pressing
your dealer.
and contact
The moving parts of this stove are propelled by high
torque electric motors. Keep all body parts away from
the auger while the stove is plugged into an electrical
outlet. These moving parts may begin to move at any
time while the stove is plugged in.
Your stove requires periodic maintenance and cleaning
(see ”MAINTENANCE ”). Failure to maintain your stove
may lead to improper and/or unsafe operation.
Disconnect the power cord before performing any
Do not place clothing or other flammable items on or
near this stove.
maintenance! NOTE: Pressing
to switch the unit
”OFF” does not disconnect all power to the electrical
components of the stove.
When installed in a mobile home, the stove must
be grounded directly to the steel chassis and bolted
to the floor. WARNING—THIS UNIT MUST NOT
BE INSTALLED IN THE BEDROOM (per HUD
requirements). CAUTION—THE STRUCTURAL
INTEGRITY OF THE MOBILE HOME FLOOR, WALL,
AND CEILING/ROOF MUST BE MAINTAINED.
Never try to repair or replace any part of the stove un-
less instructions for doing so are given in this manual.
All other work should be done by a trained technician.
Do not operate your stove with the viewing door
open. The auger will not feed pellets under these
circumstances and a safety concern may arise from
sparks or fumes entering the room.
This appliance is not intended for commercial use.
* This appliance is a freestanding heater. It is not intended to be attached to any type of ducting. It is not a furnace.
USSC
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Heating Specifications
Input Rating
38,500 BTU/hr
Heat Output1
30,000 BTU/hr.
78%
Efficiency
Heating Capacity2
Fuel Burn Rate3
Burn Time (lowest setting)
Hopper Capacity
850 sq. ft.
3.5 lbs./hr. ±5%
11-1/2 hrs. ±5%
40 lbs.
1 BTU output will vary depending on the quality of fuel. Use PFI listed fuels for the best results.
2 Heating capacity will vary depending on floor plan layout of your home, degree of insulation, and the outside temperature.
3 Pellet size may effect the actual rate of fuel feed and burn times. Fuel feed rates may vary by as much as 20%. Use PFI listed fuel for best results.
Dimensions
Height
Width
Depth
33-1/2 in.
18-1/4 in.
19-1/4 in.
Electrical Specifications
Electrical Rating
110-120 volts, 60 HZ, 4.5 Amps
520 (approx.)
Watts (maximum)
FUEL CONSIDERATIONS
Your Pellet stove is designed to burn premium hardwood pellets that comply with Association of Pellet Fuel Industries
standards. (Minimum of 40 lbs density per cubic ft, 1/4” to 5/16” diameter, length no greater than 1.5”, not less than 8,200
BTU/lb, moisture under 8% by weight, ash under 1% by weight, and salt under 300 parts per million). Pellets that are
soft, that contain excessive amounts of loose sawdust, or that have been or are wet will result in reduced performance.
Due to the different fuel densities and sizes, the fuel feed rate may vary. This may require an adjustment to the slider
damper setting or the auger feed trim setting on low.
SAFETY AND EPA COMPLIANCE
Your Pellet stove has been safety tested and listed to ASTM E 1509, by OMNI-Test Laboratories, Inc. Portland, Oregon,
USA. It is also certified and tested to EPA Phase II requirements.
4
USSC
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
INSTALLATION OPTIONS
Read this entire manual before you install and use your pellet stove. Failure to follow instructions may result
in property damage, bodily injury, or even death!
(See specific installation details for clearances and other installation requirements)
A Freestanding Unit—Placed on a non-combustible floor surface in compliance with clearance requirements for a
freestanding stove installation.
An Alcove Unit—Placed on a non-combustible floor surface in compliance with clearance requirements for an alcove
installation.
Your Forester stove may be installed to code in either a conventional or mobile home (see SPECIAL MOBILE HOME
REQUIREMENTS).
It is recommended that only a authorized technician install your Forester stove, preferably an NFI certified specialist.
IMPROPER INSTALLATION: The manufacturer will not be held responsible for damage caused by the malfunc-
tion of a stove due to improper venting or installation. Call (800) 750-2723 and/or consult a professional installer
if you have any questions.
FLOOR PROTECTION
This unit must be installed on a non-combustible floor surface. If a floor pad is used, it should be UL listed or equal.
The floor pad or non-combustible surface should be large enough to extend a minimum of 6-inches in front, 6-inches on
each side, and 1-inch behind the stove (see FIGURE 1).
Floor protection must extend under and 2-inches to each side of the chimney tee for an interior vertical installation (see
FIGURE 2). Only an elbow type connection can be used for indoor installation.
Your Forester stove will need a minimum 28” x 31” floor protector.
A Floor Protector of 1 inch thick is recommended for this installation.
USSC
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
CLEARANCES
Your Forester stove has been tested and listed for installation in residential, mobile home, and alcove applications in
accordance with the clearances given in FIGURES 3-4 and TABLE 1.
NOTE: Distance “D” on the left-hand side of your Forester stove may need to be greater than the minimum
required clearance for suitable access to the control panel.
FIGURE 3
SIDEWALL / CORNER
MINIMUM CLEARANCES
PARALLEL
A - Backwall to heater
B - Backwall to flue
C - Sidewall to flue
D - Sidewall to edge of unit
E - Adjacent wall to unit
F - Alcove depth
8.00” / 203mm
1.00” / 25mm
7.50” / 191mm
4.00” / 100mm
2.00” / 50mm
25.00” / 635mm
47.00”/ 1194mm
26.50” / 673mm
CORNER
ALCOVE
G - Alcove Hieght
Alcove Width
TABLE 1
MINIMUM CLEARANCES
(inches/mm)
FIGURE 4
MINIMUM ALCOVE CLEARANCES
6
USSC
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
VENTING REQUIREMENTS
Install vent at clearances specified by the vent manufacturer.
Do not connect the pellet vent to a vent serving any other appliance or stove.
Do not install a flue damper in the exhaust venting system of this unit.
The following installation guidelines must be followed to ensure conformity with both the safety listing of this stove and
to local building codes.
IMPORTANT! This unit is equipped with a negative draft system that pulls air through the burn pot and
pushes the exhaust out of the dwelling. If this unit is connected to a flue system other than the way explained
in this manual, it will not function properly.
MAXIMUM VENTING DISTANCE
Installation MUST include at least 3-feet of vertical pipe outside the home. This will create some natural draft to reduce the
possibility of smoke or odor during appliance shutdown and keep exhaust from causing a nuisance or hazard by exposing
people or shrubs to high temperatures. The maximum recommend vertical venting height is 12-feet for 3-inch type “PL”
vent. Total length of horizontal vent MUST NOT exceed 4-feet. This could cause back pressure. Use no more than 180
degrees of elbows (two 90-degree elbows, or two 45-degree and one 90-degree elbow, etc.) to maintain adequate draft.
PELLET VENT TYPE
A UL listed 3-inch or 4-inch type “PL” pellet vent exhaust system must be used for installation and attached to the pipe
connector provided on the back of the stove (use a 3-inch to 4-inch adapter for 4-inch pipe). Connection at back of
stove must be sealed using Hi-Temp RTV. Use 4-inch vent if the vent height is over 12-feet or if the installation is over
2,500 feet above sea level.
We recommend the use of Simpson Dura-Vent® or Metal-Fab® pipe (if you use other pipe, consult your local building
codes and/or building inspectors). Do not use Type-B Gas Vent pipe or galvanized pipe with this unit. The pellet vent
pipe is designed to disassemble for cleaning and should be checked several times during the burning season. Pellet
vent pipe is not furnished with the unit and must be purchased separately.
PELLET VENT INSTALLATION
The installation must include a clean-out tee to enable collection of fly ash and to permit periodic cleaning of the exhaust
system. 90-degree elbows accumulate fly ash and soot thereby reducing exhaust flow and performance of the stove.
Each elbow or tee reduces draft potential by 30% to 50%.
All joints in the vent system must be fastened by at least 3 screws, and all joints must be sealed with Hi-Temp RTV
silicone sealant to be airtight. The area where the vent pipe penetrates to the exterior of the home must be sealed with
silicone or other means to maintain the vapor barrier between the exterior and the interior of the home.
Vent surfaces can get hot enough to cause burns if touched by children. Noncombustible shielding or guards may be
required.
Only an elbow type connection can be used for indoor installation.
PELLET VENT TERMINATION
Do not terminate the vent in an enclosed or semi-enclosed area, such as; carport, garage, attic, crawl space, under a
sundeck or porch, narrow walkway, or any other location that can build up a concentration of fumes.
The termination must exhaust above the outside air inlet elevation.
The termination must not be located where it will become plugged by snow or other materials.
Do not terminate the venting into an existing steel or masonry chimney.
USSC
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
VENT TERMINATION CLEARANCES:
A) Minimum 4-foot clearance below or beside any door or window that opens.
B) Minimum 1-foot clearance above any door or window that opens.
C) Minimum 3-foot clearance from any adjacent building.
D) Minimum 7-foot clearance from any grade when adjacent to public walkways.
E) Minimum 2-foot clearance above any grass, plants, or other combustible materials.
F) Minimum 3-foot clearance from an forced air intake of any appliance.
G) Minimum 2-foot clearance below eves or overhang.
H) Minimum 1-foot clearance horizontally from combustible wall.
I) Must be a minimum of 36-inches above the roof and 24-inches above the highest point or the roof within 10-feet.
G
FIGURE 5
VENT TERMINATION CLEARANCES
8
USSC
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
THROUGH THE WALL INSTALLATION (RECOMMENDED INSTALLATION)
To vent the unit through the wall, connect the pipe adapter
to the exhaust motor adapter. If the exhaust adapter is at
least 18-inches above ground level, a straight section of
pellet vent pipe can be used through the wall.
Your Forester dealer should be able to provide you with
a kit that will handle most of this installation, which will
include a wall thimble that will allow the proper clearance
through a combustible wall. Once outside the structure, a
3-inch clearance should be maintained from the outside
wall and a clean out tee should be placed on the pipe with
a 90-degree turn away from the house. At this point, a
3-foot (minimum) section of pipe should be added with a
horizontal cap, which would complete the installation (see
FIGURE 6).
A support bracket should be placed just below the
termination cap or one every 4-feet to make the system
more stable. If you live in an area that has heavy snowfall,
it is recommended that the installation be taller than 3-feet
to get above the snowdrift line. This same installation
can be used if your stove is below ground level by simply
adding the clean-out section and vertical pipe inside until
ground level is reached. With this installation you have to
be aware of the snowdrift line, dead grass, and leaves. We
recommend a 3-foot minimum vertical rise on the inside or
outside of the house.
FIGURE 6
TYPICAL THROUGH THE WALL INSTALLATION
The “through the wall” installation is the least expensive and simplest installation. Never terminate the end vent under a
deck, in an alcove, under a window, or between two windows. We recommend Simpson Dura-Vent® or Metal-Fab® kits.
THROUGH THE ROOF/CEILING INSTALLATION
When venting the stove through the ceiling, the pipe is connected the same as through the wall, except the clean-out
tee is always on the inside of the house, and a 3-inch adapter is added before the clean-out tee.
You must use the proper ceiling support flanges and roof flashing (supplied by the pipe manufacturer; follow the pipe
manufacturer’s directions). It is important to note that if your vertical run of pipe is more than 15-feet, the pellet vent pipe
size should be increased to 4-inches in diameter.
Do not exceed more than 4-feet of pipe on a horizontal run and use as few elbows as possible. If an offset is required,
it is better to install 45-degree elbows rather than 90-degree elbows.
USSC
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
OUTSIDE AIR SUPPLY (optional, unless installing in a mobile home)
Depending on your location and home construction, outside air may be necessary for optimal performance.
Metal pipe (solid or flexible) must be used for the outside air installation. PVC pipe is NOT approved and should NEVER
be used.
A wind shield over the termination of the outside air pipe or a 90-degree elbow or bend away from the prevailing winds
MUST be used when an outside air pipe is installed through the side of a building. The outside air termination MUST
be at least 1-foot away from the exhaust system termination.
The outside air pipe on your Forester stove is 2” OD. The outside air connecting pipe must be at least 2” ID. The outside
air connection used MUST NOT restrict the amount of air available to your stove. The outside air connecting pipe must
be as short and free of bends as possible, and it must fit over, not inside, the outside air connection to the stove.
FIGURE 8
TYPICAL FRESH AIR TERMINATION
NOTE: Dimensions from the floor to your stoves
inlet/exhaust pipes are approximate and may vary
FIGURE 7
EXHAUST/INLET LOCATIONS
depending on your installation.
SPECIAL MOBILE HOME REQUIREMENTS
WARNING! - DO NOT INSTALL IN A SLEEPING ROOM
CAUTION! - THE STRUCTURAL INTEGRITY OF THE MOBILE HOME FLOOR, WALL, AND CEILING/ROOF
MUST BE MAINTAINED.
In addition to the previously detailed installation requirements, mobile home installations must meet the following
requirements:
•
•
The stove must be permanently attached to the floor.
The stove must be electrically grounded to the steel chassis of the mobile home with 8 GA copper wire using a
serrated or star washer to penetrate paint or protective coating to ensure grounding.
•
•
Vent must be 3 or 4-inch “PL” Vent and must extend a minimum or 36-inches above the roofline of the mobile home
and must be installed using a UL listed ceiling fire stop and rain cap.
When moving your mobile home, all exterior venting must be removed while the mobile home is being relocated.
After relocation, all venting must be reinstalled and securely fastened.
•
Outside Air is mandatory for mobile home installation. See your dealer for purchasing.
•
Check with your local building officials as other codes may apply.
10
USSC
Download from Www.Somanuals.com. All Manuals Search And Download.
Understanding your stove
How your stove works
Your Forester stove utilizes a vertical auger fuel feed system that is operated by a microprocessor controlled digital
circuit board. The digital circuit board allows the vertical auger fuel feed system to run in a timer-based, non-continuous
cycle; this cycling allows the auger to run for a predetermined period of seconds. The auger pushes pellets up a chute
located in the hopper which in turn falls through another chute into the burnpot. Your stove is equipped with an automatic
ignition system that should ignite the fuel within 3 - 5 minutes from pressing the
button. As pellets enter the burnpot
and ignite, outside air is drawn across the fuel and heated during the combustion process which is then pulled through
the heat exchanger by the exhaust motor or draft fan. As the stove heats up, room air is circulated around the heat
exchanger by means of a room air blower, distributing warm air into the room.
The amount of heat produced by the stove is proportional to the rate of the fuel that is burned, and this rate is controlled
In order to maintain combustion of the fuel at a desired rate, the air provided to the
by the Fuel Control button
.
burn chamber by the exhaust or draft fan must be maintained precisely. Too little air will result in a flame that is non-
energetic or lazy. If the fuel continues to flow with too little air for long enough, the burn pot will fill with too much fuel and
the fire will smother out. To much air will result in a flame that is overactive or aggressive. The flame in this situation is
typically very blue at the bottom and resembles a blow torch. If this situation continues, the fuel in the burn pot will be
consumed and the fire will go out.
Matching the amount of air required for proper combustion to the fuel rate is the primary objective in effectively burning
pellets of various brands and qualities in your stove. The air to fuel ratio can be adjusted to allow almost any fuel quality
to burn effectively by following the procedures detailed in the remainder of this manual.
Because a forced draft pressure is required for the combustion process inside your stove, it is extremely important that
the exhaust system be properly installed and maintained. And, that when operating your stove, you make sure that the
viewing door is properly sealed.
FIGURE 9
DIGITAL CONTROL PANEL
USSC
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
START-UP PROCEDURE
Never use gasoline, gasoline-type lantern fuel, kerosene, charcoal lighter fluid, or similar liquids to start or
“freshen up” a fire in this stove. Keep all such liquids well away from the stove while it is in use.
1.) Verify that the hopper is clean and free of foreign matter including pellet fines and dust.
2.) Verify that all of the required exhaust/inlet connections have been made in accordance with this manual and that the
stove is plugged into an outlet (an outlet surge protector is highly recommended).
3.) Fill the hopper with wood pellets; do not allow any part of the bag or any other foreign material into the hopper, as
this may jam the auger.
4.) Ensure that all pellet matter is cleared from the hopper seating surface.
5.) Close the hopper lid. The unit WILL NOT feed fuel with the hopper lid open.
6.) Make sure that the viewing door is securely closed (the safety pressure switch will not allow the stove to feed fuel if
there is no draft pressure inside the stove).
7.) Press the
button on the control pad and then select the highest heat range by pressing the
button.
8.) The stove will begin to feed fuel and the auto-start ignitor will ignite the fuel in approximately 3 to 5 minutes.
When starting the unit for the first time, the auger mechanism will not be primed with pellets. This will cause
the auto-start ignitor to time out and shut the unit down. Pressing the
button again will restart the startup
sequence and the stove should ignite properly. However, on some occassions, this process may need to be
repeated until ignition depending on fuel size and quality.
As an alternative method to the initial startup, prior to step 6 above, you may add a handful of pellets or add pellets up
to the ignition port in the burnpot. Proceed to step 6 thru 8. The pellets should ignite and heater begin proper operation.
Once a consistent flame has been established, you can adjust the heat range
on the control pad to your desired
setting, low, medium, or high. (Note: The distribution blower will not function until the heat exchanger in the stove
reaches the factory preset temperature).
First Fire: Adjust the heat range to a medium setting and allow the stove to operate in this manner for
approximately three (3) hours (or more if necessary), allowing the stove to “cure out” as the paint and oils
from the manufacturing process burn off. We recommend that you open doors and windows in your home
during this process. Then adjust heat range to your desired setting.
SHUT DOWN PROCEDURE
WARNING: Never shut down this unit by unplugging it from the power source.
Press the
button on the control pad to put the stove in shut down mode. Once this is done, the auger will stop
feeding pellets, but the distribution blower and exhaust blower will continue to operate. When the internal temperature
of the unit drops below the factory preset temperature, the distribution blower and exhaust blower will cease to operate
and the unit will be completely shut down.
The hotter the unit is during its operation, the longer it will take for the stove to complete the shut down cycle. If the
stove stays on for more than 2 hours after pressing the
button and you are sure that the fire is out, the stove can
be unplugged from the outlet. After approximately 10 seconds, the unit can be re-connected to the power source and
the control board will be reset.
12
USSC
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
DAILY OPERATION
The hopper and stove top will be hot during operation; therefore, you should always use some type of hand
protection when refueling your stove.
Never place your hand near the auger while the stove is in operation.
In the event of a power outage, the stove WILL NOT function. It is very important that unit be vented properly (with
outside air), as the natural draft is needed to clear the smoke from the stove during a power outage. If the unit was ON
when the power outage occurred, one of the following will take place:
1.) If the stove is still warm, it will resume feeding fuel and continue to operate normally. If the fire has gone out, you
will have to press the
button and then the
button again to begin a new start-up sequence.
2.) If the stove has cooled-off, it will reset to its OFF condition. At this point, you may press the
button and the
unit will begin a new start-up sequence.
NOTE: The unit will also shut down in the event of an exhaust blower failure; if this is the case, the unit will not re-start
and you must contact Customer Service at (800) 750-2723.
SAFETY AND CONVENIENCE FEATURES
Your stove includes an auto-start igniter as a standard feature. The use of other fire starter materials (wood chips,
starter gel, etc.) is not necessary. By simply pressing the
to feed fuel and automatically start within 3 to 5 minutes.
button on the digital control panel, your stove will begin
For safety, this stove incorporates a safety pressure switch that helps ensure that everything is in proper working order
before feeding fuel to the burn pot. Because the stove works using an induced draft pressure, the stove will not continue
to operate if the viewing door is left open; or if the exhaust blower fails or the exhaust system is blocked.
The temperature limit control (Thermodisc) will prevent your stove from operating at abnormally high temperatures.
Should the stove temperature reach the factory pre-set limit, 200°F(93°C), the temperature limit control will automatically
stop the auger feed rate until the temperature returns to a normal condition.
Maintenance
Failure to clean and maintain this unit as indicated can result in poor performance and safety hazards.
Unplug your stove’s electrical cord prior to removing the back panel or opening the exhaust system for any
inspection, cleaning, or maintenance work.
Never perform any inspections, cleaning, or maintenance on a hot stove.
Do not operate stove with broken glass , leakage of flue gas may result.
EXHAUST SYSTEM
The by products of combustion contain small particles of fly ash. Fly ash will collect in the exhaust venting system and
restrict the flow of flue gases. Incomplete combustion, such as during startup, shutdown, or incorrect operation of the
stove will lead to soot formation which will collect in the exhaust system. Therefore, it is important that the exhaust
system be inspected and cleaned at least monthly during the burning season.
Check the clean out tees periodically to determine the required cleaning schedule. 3 or 4-inch chimney brushes are
available for chimney cleaning. If the exhaust system or outside air pipes have screens on them, frequently clean the
screen. A plugged screen will shut off combustion air and cause a fire to die or burn poorly.
USSC
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
INTERIOR CHAMBERS
Periodically remove and clean the burnpot and the area inside the burnpot housing. In particular it is advisable to clean
out the holes in the burnpot to remove any build up that may prevent air from moving through the burn pot freely.
If a vacuum is used to clean your stove, we suggest using a vacuum designed for ash removal. Some regular vacuum
cleaner (i.e. shop vacs) may leak ash into the room.
ASH DISPOSAL
Ashes should be placed in a metal container with a tight fitting lid. The closed container of ashes should be placed on
a noncombustible floor or on the ground, well away from all combustible materials, pending final disposal. If the ashes
are disposed of by burial in soil or otherwise locally dispersed, they should be retained in the closed container until all
cinders have been thoroughly cooled.
CHECK AND CLEAN THE HOPPER
Check the hopper periodically to determine if there is any sawdust or pellets that are sticking to the hopper surface.
Clean as needed.
DOOR AND GLASS GASKETS
Inspect the main door and glass window gaskets periodically. The main door may need to be removed to have frayed,
broken, or compacted gaskets replaced by your authorized “Forester” dealer.
BLOWER MOTORS
Clean the air holes on the motors of both the exhaust and distribution blowers annually. Remove the exhaust blower
from the exhaust duct and clean out the internal fan blades as part of your fall start-up.
PAINTED SURFACES
Painted surfaces may be wiped down with a damp cloth. If scratches appear, or you wish to renew your paint, contact
your authorized “Forester” dealer to obtain a can of suitable high-temperature paint.
GLASS
We recommend using a high quality glass cleaner. Should a build up of creosote or carbon accumulate, you may wish
to use 000 steel wool and water to clean the glass. In the event you need to replace the glass, only high temperature
ceramic glass of the correct size and thickness may be used. Contact your authorized “Forester” dealer to obtain this
glass.
FALL START UP
Prior to starting the first fire of the heating season, check the outside area around the exhaust and air intake systems
for obstructions. Clean and remove any fly ash from the exhaust venting system. Clean any screens on the exhaust
system and on the outside air intake pipe. Turn all of the controls on and make sure that they are working properly. This
is also a good time to give the entire stove a good cleaning throughout.
SPRING SHUTDOWN
After the last burn in the spring, remove any remaining pellets from the hopper and the auger feed system. Scoop out
the pellets and then run the auger until the hopper is empty and pellets stop flowing (this can be done by pressing the
“ON” button with the viewing door closed). Vacuum out the hopper. Thoroughly clean the burnpot, and firebox. It may
be desirable to spray the inside of the cleaned hopper with an aerosol silicone spray if your stove is in a high humidity
area. The exhaust system should be thoroughly cleaned.
YEARLY SERVICING
A yearly servicing and cleaning by your authorized “Forester” dealer is recommended. A fee may be charged for this
service.
14
USSC
Download from Www.Somanuals.com. All Manuals Search And Download.
Trouble Shooting
Disconnect the power cord before performing any maintenance! NOTE: Pressing the OFF button does not
disconnect all power to the electrical components of the stove.
Never try to repair or replace any part of the stove unless instructions for doing so are given in this manual.
All other work should be done by a trained technician.
PROBLEM
CAUSE: Lack of combustion air intake.
Orange, lazy flame_excessive fuel build-up in
the burnpot
•
Clean out the burnpot.
•
Make sure that the viewing door is closed and sealed properly. If not, check or replace
door gaskets.
•
•
Check that all outside connections are clear of any obstructions.
Check the exhaust system; clean as needed.
PROBLEM
CAUSE: Burnpot burns out of fuel
Fire goes out or stove shuts down.
A. Auger system is jammed or there is a “bridging” of the fuel in the hopper, preventing fuel
from flowing into the auger feed system. Check that the Auger motor is functioning. Check
wiring and the auger to motor connection.
A. Three lights are bright and flashing.
B. Three lights are bright but not flashing
B. Hopper is empty, refill the hopper.
C. The RED light is bright and flashing, but the
other are not.
C. The high temperature thermodisc has tripped. Check the wiring connections. Possibly
replace thermodisc.
D. Three lights are not bright.
D. Loss of power.
Other possible causes/solutions:
•
Loss of draft pressure. Make sure that the viewing door is closed and sealed properly. If
not, check and/or replace door gaskets. Check that all outside connections are clear of any
obstructions. Check the exhaust system; clean as needed.
•
Check that the pressure switch connection to the firebox is free of ash or clear of obstructions.
PROBLEM
CAUSE: No power orAuto-Start Igniter fails to ignite the fuel in the burnpot.
•
•
•
•
Make sure power is supplied to stove.
Stove does not start a fire when the
is pushed
button
Turn the stove OFF. Clear the unburnt fuel from the burnpot and try again.
Check the pellet quality. Replace if moist, wet, or dirty.
Loss of draft pressure. Make sure that the viewing door is closed and sealed properly. If
not, check and/or replace door gaskets. Check that all outside connections are clear of any
obstructions. Check the exhaust system; clean as needed.
•
•
•
Check that the pressure switch connection to the firebox is free of ash or clear of obstructions.
Check that the auto-start igniter is not blocked with ash or soot.
The auto-start igniter gets “red hot” during start-up. If you can not visibly see the igniter
glowing during start-up, then the igniter may need to be replaced or there is a problem with
the electrical control system.
PROBLEM
CAUSE: Stove is overheating. The stove has been working too long or room temp. is too high
Two lights are bright, the feeding light is off, and
meanwhile the orange light is bright
•
Allow stove to shutdown automatically, then restart.
PROBLEM
CAUSE: The burnpot is positioned incorrectly.
•
Put burnpot in correct position, as indicated by the slot on the burnpot.
A. Stove does not start when
is pressed.
B. Prolonged ignition time with excess smoke.
C. Burning is not active.
USSC
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts Diagram
16
USSC
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST
5824
Item Part No. Title
Qty. Item Part No. Title
Qty
1
1
1
1
1
1
1
1
2
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
891603
891604
891605
891606
88139
Door Frame Assy. (5824-05-01-00)
Door Frame Wldmt (5824-05-00)
Nylon Shim (5824- 08-01)
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
N/S
N/S
N/S
891631
891632
891633
80564
Firebox Weldment (5824-01-01-00)
Vent Slides (5824-01-18)
A
B
C
D
E
F
Ignitor Sleeve (5824-02-12)
Door Hndle Wldmt (5824-05-02-00)
Glass Gasket (5824-09-00)
Ignitor Assembly (5824-21-00)
Exhaust Hsg Wld (5824-01-01-11-00)
Exhast Maint. Cover (5824-01-16-01)
Smoke Weldment (5824-01-09-00)
Exhaust Motor Assy (5824-01-08)
125°F(52°C) Sensor (5824-22-00)
Hopper Frame (5824-02-01-00)
L/R Wiring Guide Rail (5824-02-03)
Back Wiring Guide Rail (5824-02-04)
Back Panel (5824-10)
891634
891635
891636
80565
88140
Glass (5824-05-04)
891607
88141
Glass Retainer (5824-05-01-09)
Door Gasket (5824-08-00)
G
2
3
4
5
6
7
8
9
891608
891609
891610
891611
891612
891613
891614
891615
891616
891617
891618
891619
80562
Firebox Frt. Panel (5824-01-01-13)
Door Hook Pin (5824-01-15)
Hook Pin Tube (5824-01-16)
Side Wall Panel (5824-08)
80566
891637
891638
891639
891640
80567
Left Wall Panel (5824-09)
Ash Pan Weldment (5824-01-02-00)
Burnpot Support (5824-01-01-04)
Burnpot (5824-01-10-00)
Pressure Switch (5824-20-00)
Support Pressure Sw. (5824-02-06)
Insulation Panel (5824-01-04-01)
198°F(92°C) Sensor (5824-23-00)
Circuit Board (5824-18-00)
891641
891642
80568
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
Air-In Grid (5824-07-00)
Air-Out Grid (5824-06-00)
80569
Insulation Cover (5824-01-03)
Top Panel Assy. (5824-03-00)
Microswitch (5824-19-00)
80570
Power Supply Box (5824-17-00)
Support, Pwr Sply Box (5824-02-05)
Capacitance (5824-16-00)
891643
80571
891620
891621
891622
891623
891624
891625
891626
891627
891628
891629
891630
80563
Micro-sw Hsg-1 (5824-03-01-03-01)
Micro-sw Hsg-2 (5824-03-01-03-02)
Top Insulation Panel (5824-01-06)
Top Air Guide Cover (5824-01-07)
Support, Top Air Guide (5824-01-05)
Maintenance Panel (5824-01-17)
Upper Hinge (5824-01-11-01)
Uppr Hng Fixing Pin (5824-01-11-02)
Lower Hinge (5824-01-12)
80572
Motor (5824-15-00)
891644
891645
891646
891647
891648
891649
891675
891685
891686
Feed Tube Wldmt (5824-02-02-01-00)
Support, Motor (5824-02-02-01-09)
Feed Tube Cover (5824-02-02-01-04)
Big Bearing (5824-11-00)
Small Bearing (5824-13-00)
Auger Weldment (5824-02-02-01-05)
Vermiculite Board Front W/Cutout
Vermiculite Board Front Top
Lower Hinge Pin (5824-01-14)
Hinge Sleeve (5824-01-13)
Vermiculite Board Sides
Distribution Motor Assy (5824-11-00)
USSC
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Wiring Diagram
18
USSC
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
USSC
19
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO ORDER REPAIR PARTS
THIS MANUAL WILL HELP YOU OBTAIN EFFICIENT, DEPENDABLE SERVICE
FROM YOUR FORESTER, AND ENABLE YOU TO ORDER REPAIR PARTS COR-
RECTLY.
KEEP THIS MANUAL IN A SAFE PLACE FOR FUTURE REFERENCE.
WHEN WRITING, ALWAYS GIVE THE FULL MODEL NUMBER WHICH IS ON
THE NAMEPLATE ATTACHED TO THE HEATER.
WHEN ORDERING REPAIR PARTS, ALWAYS GIVE THE FOLLOWING INFOR-
MATION AS SHOWN IN THIS LIST:
1. THE PART NUMBER
2. THE PART DESCRIPTION
3. THE MODEL NUMBER: 5824
4. THE SERIAL NUMBER:____________________
United States Stove Company
A
227 Industrial Park Road
P.O. Box 151
South Pittsburg, TN 37380
S
C
U
S
(800) 750-2723
WWW.USSTOVE.COM
P
Download from Www.Somanuals.com. All Manuals Search And Download.
|