UBCD396T
Owner's Manual
OWNER'S MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING!
Uniden does not represent this unit to be
waterproof. To reduce the risk of fire or electrical
shock, do not expose this unit to rain or moisture.
Astro ® , DPL ® , Digital Private Line ® , Motorola ®
,
PL ® , PRIVACY PLUS ® , Private Line ®
,
SMARTNET ® ,and SMARTZONE ® are registered
trademarks of Motorola, Inc.
LTR ® is a registered trademark of E.F. Johnson Co.
EDACS ® is a registered trademark of M/A-COM
Private Radio Systems Inc.
Other trademarks used throughout this manual are the
property of their respective holders.
Important: If you use the supplied AC adaptor to
power the scanner but have not installed batteries in
the scanner, never turn the scanner off by
disconnecting the AC adaptor or unplugging it from
the AC outlet.
This might corrupt the scanner’s memory.
Always use to turn the scanner off before
disconnecting AC power.
Precautions
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Introduction ...............................................................................................7
Feature Highlights ..................................................................................
8
About This Manual ............................................................................. 13
Using the Multifunction Scroll Control .............................................13
Entering Text ................................................................................. 13
How the Scanner’s Controls Are Represented in
This Manual ....................................................................................14
Understanding Scanning ...................................................................... 16
Understanding the Scanner’s Memory .............................................. 16
What is Scanning? ............................................................................ 16
What is Searching? ........................................................................... 17
What is CTCSS/DCS? ...................................................................... 17
Conventional Scanning ..................................................................... 19
Simplex Operation ......................................................................... 20
Repeater Operation ....................................................................... 20
What is Trunk Tracking? ................................................................... 20
Trunked Scanning ............................................................................. 21
Types of Trunking Systems ................................................................22
Motorola Trunking .......................................................................... 22
EDACS Trunking ........................................................................... 24
LTR Trunking ................................................................................. 25
I-Call (Motorola/EDACS) .................................................................. 26
Where To Get More Information ........................................................ 26
Information On The Internet .......................................................... 26
Included With Your Scanner ................................................................. 27
Setting Up Your Scanner ...................................................................... 28
Using Internal Batteries ..................................................................... 28
Using Rechargeable Batteries ........................................................... 29
Removing the Display Sticker ............................................................ 30
Using AC Power ................................................................................ 30
Connecting the Antenna .................................................................... 31
Connecting an Optional Antenna ................................................... 31
Connecting an Earphone/Headphone ............................................... 31
Connecting an Extension Speaker .................................................... 31
Attaching the Belt Clip ....................................................................... 32
Attaching the Wrist Strap ................................................................... 32
A Look At The Keypad ....................................................................... 32
A Look At The Display ....................................................................... 35
Using Menu ........................................................................................37
Using Func ........................................................................................ 37
Basic Operation ..................................................................................... 38
Turning On the Scanner and Setting the Squelch ............................. 38
Scanning Systems ............................................................................. 39
Selecting Systems to Scan ................................................................ 40
Selecting System Channel Groups .................................................... 41
Locking/Unlocking Systems .............................................................. 41
Locking/Unlocking Channels ............................................................. 41
ID Scan/ID Search Mode .................................................................. 42
Temporarily Holding On a System ..................................................... 42
Holding On a Channel ...................................................................... 42
Quickly Storing an ID During ID Search ............................................ 43
Quick-Storing Channels or Talk Group ID’s ...................................... 43
Quickly Recalling Channels .............................................................. 44
Monitoring Trunking Activity .............................................................. 44
Toggling Channel Alpha Tags ............................................................ 44
Using the Menu ...................................................................................... 45
Programming Systems Menu ............................................................ 47
Contents
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Other Settings ............................................................................................ 49
Displaying System Information ................................................................. 49
Viewing Memory Used ........................................................................... 49
Viewing the Firmware Version ................................................................49
Adjusting the Key Beep ............................................................................ 49
Locking/Unlocking the Keypad and Scroll ................................................ 49
Turning Power Save On or Off ................................................................. 50
Priority Scan ............................................................................................. 50
Using the Backlight ................................................................................... 50
Setting the Audio AGC .............................................................................. 51
Adjusting the Display Contrast ..................................................................51
Initializing the Scanner’s Memory ............................................................. 52
Connecting Your Scanner to a Personal Computer .................................. 52
Using the Cloning Options ........................................................................ 53
Wired Cloning ........................................................................................ 53
On-Air Cloning ....................................................................................... 54
Programming Radio Systems ...................................................................56
Programming Conventional Systems ........................................................57
Entering/Editing Conventional Channel Groups .....................................57
Entering/Editing Conventional Channels ................................................58
Programming Motorola Systems .............................................................. 59
Setting System Frequencies .................................................................. 60
Setting Modulation ..................................................................................61
Setting Attenuation ................................................................................. 61
Entering/Editing Motorola Channel Groups ............................................62
Entering/Editing Motorola Channels .......................................................62
Programming EDACS Systems ................................................................ 63
Setting System Frequencies ................................................................. 64
Entering/Editing EDACS Channel Groups ............................................. 65
Entering/Editing EDACS Channels ........................................................ 65
Programming LTR Systems ...................................................................... 66
Setting System Frequencies .................................................................. 67
Entering/Editing LTR Channel Groups .................................................. 67
Entering/Editing LTR Channels/Talkgroups ........................................... 68
Programming/Editing Optional Settings ................................................. 70
System-Level Settings .............................................................................. 70
Editing the System Name ...................................................................... 70
Editing the System Quick Key ............................................................... 71
Setting System Lockout ......................................................................... 71
Setting the System Hold Time ............................................................... 72
Setting the Channel Delay Time .............................................................72
Setting ID Scan/Search (Trunked Systems Only) .................................. 73
Setting the Band Plan
(Motorola P25 and VHF/UHF Systems Only).......................................74
Editing the Fleet Map (Motorola Systems Only) .....................................75
Setting the Motorola Status Bit (Motorola Systems Only) ...................... 76
Setting the End Code Operation (Motorola Systems Only) ................... 77
Setting I-Call (Motorola and EDACS Systems Only) ..............................77
Setting Emergency Alert (Motorola and EDACS Systems Only) ........... 78
Setting Control-Channel Only (Motorola Systems Only) ........................78
Reviewing Locked Out Frequencies .......................................................79
Clearing All Locked-Out IDs ................................................................... 79
Adjusting the P25 Level (Motorola and Conventional Systems Only) ....79
Setting the EDACS ID Format (EDACS Systems Only) .........................80
Setting System Attenuation (Trunked Systems Only) ............................ 81
Deleting Systems ................................................................................... 81
Copying Systems ................................................................................... 81
Group-Level Settings ................................................................................ 82
Entering/Editing the Group Name .......................................................... 82
Setting the Group Quick Key ..................................................................83
Setting Group Lockout ............................................................................83
Deleting Groups ......................................................................................83
Contents
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Channel-Level Settings..............................................................................84
Editing the Channel Name...................................................................... 84
Editing Frequencies (Conventional Channels Only) ...............................85
Setting Channel Priority (Conventional Channels Only) .........................85
Setting Channel Alert ..............................................................................86
Editing the Talk Group ID (Trunked Channels Only) .............................. 86
Setting CTCSS/DCS (Conventional Channels Only).............................. 87
Setting the System Frequency Modulation ............................................ 88
Setting Channel Attenuation (Conventional Channels Only) ................. 88
Setting Channel Lockout ........................................................................ 89
Deleting Channels ................................................................................. 90
Copying/Pasting Channels .................................................................... 90
Searching and Storing .............................................................................. 91
Service Search ..........................................................................................91
Quick Search ............................................................................................ 92
CTCSS/DCS Search .................................................................................92
Custom Search ......................................................................................... 93
Editing a Custom Search Range ........................................................... 94
Editing a Service Search ....................................................................... 95
Auto Search and Store ............................................................................. 96
Selecting a System............................................................................... 97
Storing a Conventional System ............................................................ 97
Storing a Trunked System .................................................................... 98
Optimizing P25 Performance .................................................................. 99
Using the Close Call Feature .................................................................. 100
Setting Close Call Options ...................................................................... 101
Close Call Hits ........................................................................................ 103
Search and Close Call Options .............................................................. 104
Managing Locked-Out Frequencies ........................................................104
Unlocking All Frequencies ................................................................... 104
Reviewing Locked Out Frequencies .................................................... 104
Searching for Subaudible Tones ............................................................ 104
Screening Out Broadcast Sources ......................................................... 105
Finding Repeater Output Frequencies ....................................................106
Setting the Maximum Auto Store Value .................................................. 107
Setting the Modulation Type ................................................................... 107
Setting Attenuation ................................................................................. 107
Setting Data Skip .................................................................................... 108
Setting the Delay Time ........................................................................... 109
Setting the Search Frequency Step ........................................................ 109
APCO 25 Threshold Level Settings ........................................................ 109
Using Tone-Out ........................................................................................ 110
Fire Tone-Out Introduction ...................................................................... 110
Setting Tone-Out Standby ................................................................... 110
Setting Up Tone-Out ............................................................................ 110
Care and Maintenance ............................................................................. 113
General Use ............................................................................................ 113
Location .................................................................................................. 113
Cleaning ................................................................................................. 113
Repairs .................................................................................................... 114
Birdies ..................................................................................................... 114
Contents
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting ...................................................................................... 115
Specifications .......................................................................................... 119
Optional Accessories .............................................................................. 122
Appendix .................................................................................................. 123
Preset Fleet Maps ................................................................................... 123
User Defined Fleet Maps ........................................................................ 125
Type I Programming Information ......................................................... 125
Size Code Restrictions ........................................................................ 126
Planning ....................................................................................................127
Collecting Information ............................................................................. 127
Filling Out The Conventional System Worksheet ................................... 129
System Name and Quick Key .............................................................. 129
Group Name and Quick Key ................................................................ 129
Frequency-Alpha Tag-Priority-CTCSS/DCS ........................................ 129
Filling Out The Motorola Worksheet ....................................................... 130
System Name and Quick Key .............................................................. 130
System Type ........................................................................................ 130
System Frequencies ............................................................................ 131
Fleet Map (Type I or Type I/Type II Hybrid Only) ................................ 131
Band Plan (VHF or UHF Only) ............................................................ 131
Group Name and Quick Key ................................................................ 131
Talk Group ID-Alpha Tag-Alert ............................................................ 131
Filling Out the LTR and EDACS Worksheet ........................................... 132
System Name and Quick Key .............................................................. 132
System Frequencies and LCN ............................................................. 132
Group Name and Quick Key ................................................................ 132
Talk Group ID-Alpha Tag-Alert ............................................................ 132
Conventional System Worksheet ........................................................... 133
Motorola System Worksheet .................................................................. 134
LTR/EDACS System Worksheet ............................................................. 136
Warranty ....................................................................................................138
Contents
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Your UBCD396T scanner is a state-of-the-art scanner radio
with TrunkTracker IV™ and automatic scanning capabilities.
You can store frequencies such as police, fire/emergency,
marine, air, amateur, and other communications into the
scanner. You can carry it with you wherever you go. You can
use the scanner’s scroll control to quickly select channels
and frequencies, and you can automatically program
channels in a system using the AutoStore feature.
Use your scanner to monitor:
• Analog and digital trunked public safety systems
(unencrypted only) *
• Police and fire departments (including rescue and
paramedics)
• Business/Industrial radio and utilities
• Marine and amateur (ham radio) bands
• Air band
• Railroad
• UHF CB Radio
• CB Radio
Your scanner can monitor the following bands.
87.9875
136.9875
224.9000
12.5
* Motorola ® Astro ® , SMARTNET ® ,SMARTZONE ®, and PRIVACY PLUS ® ,
M/A-COM Private Radio Systems Inc. EDACS ® Wide, Narrow, and SCAT,
and E.F. Johnson Co. LTR systems.
Introduction
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Feature Highlights
General
Close Call™ RF Capture Technology - You can set
the scanner so it detects and provides information
about nearby radio transmissions. See “Using the
Close Call Feature” on Page 100 for more information.
Dynamically Allocated Channel Memory - Your
scanner’s memory is organized so that it more closely
matches how radio systems actually work, making it
easier to program and use your scanner and
determine how much memory you have used and how
much you have left.
Pre-Programmed Systems - Your UBCD396T may
come pre-programmed with local systems (for
Australian and NZ Emergency Services for example)
as a complementary start.
100 Quick Keys – You can set the scanner so you
can quickly select systems and groups by using the
keypad. This makes it easy to listen to or quickly lock
out those systems or groups you don’t want to scan.
9 Service Searches - frequencies are preset in
separate Police, Marine, Railroad, Air, CB Radio,
UHF CB Radio, Racing, TV Broadcast, and FM
Broadcast searches, to make it easy to search and
scan for specific transmissions.
Lockout – You can lock out any system, group,
frequency, or channel while scanning. If you lock out a
system or group, any channels belonging to that
system or group are also locked out.
You can lock out up to 200 frequencies. The scanner
skips locked-out frequencies while using the Close
Call feature or while searching.
CTCSS and DCS Squelch Modes – prevent
interference from stations not using the mode you
select.
Feature Highlights
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Analog and Digital Audio AGC – Helps automatically
balance the volume level between different radio
systems.
Fire Tone-Out Standby – Lets you set the scanner to
alert you if a two-tone sequential page is transmitted.
You can set up to 10 settings (transmit frequency, tone
frequencies) then select one for standby monitoring.
Broadcast Screen – Sets the scanner so it ignores
Close Call ™ or search hits on known broadcast
frequencies including pager frequencies.
Custom Screen – Lets you input up to 10 frequency
ranges that the scanner will ignore during Close
Call™ or search operation.
Dropout Delay – You can set whether the scanner
pauses at the end of a transmission to wait for a reply.
You can set the delay time for each system you scan,
and while searching and using the Close Call ™
feature.
Attenuator – You can set the scanner’s attenuator to
reduce the input strength of strong signals by about
18 dB.
Repeater Reverse – You can set the scanner so it
switches to the input frequency on a conventional
repeater system.
Channel Alert – You can set the scanner so it alerts
you when there is activity on any channel you specify.
Memory Check – Lets you see at a glance how much
total memory is left.
Scan and Search Operation – Lets you include
selected service searches or custom search ranges
during normal scan operation.
Custom Alerts – For each alert in the scanner (such
as channel alert, Close Call alert, emergency alert),
you can select from 9 different tone patterns and also
set the alert volume level independently from the main
volume level.
Feature Highlights
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Automatic Channel Step – Accepts frequencies on
any valid channel step, even if it does not fall within
the band plan’s default step.
Frequency Step – Lets you select a frequency step
(5, 6.25, 7.5, 8.33, 10, 12.5,15, 20, 25, 50 or 100 kHz)
for manual mode and chain search mode. The
scanner’s auto step feature lets you set the scanner
so it automatically chooses the correct step.
Quick Recall – Lets you quickly select a specific
channel by choosing the system, group, and channel.
Scan/Search Delay – You can set the scanner so it
remains on a frequency up to 5 seconds after the last
transmission to wait for a possible reply.
Text Tagging – You can name each system, group,
channel, talk group ID and custom search range,
using up to 16 characters per name.
Unique Data Skip – Allows your scanner to skip
unwanted data transmissions and reduces birdies.
Duplicate Frequency Alert – Alerts you if you try to
enter a duplicate name or frequency already stored in
a system.
Memory Backup – If power is lost or disconnected,
the scanner retains the frequencies you programmed
in its memory.
Trunk Tracking
Trunk Tracker IV ™ Operation – Follows
unencrypted conversations on analog Motorola,
Motorola Astro 25 (APCO 25), EDACS, EDACS SCAT,
and LTR trunked radio systems, including systems in
VHF, UHF, 800MHz Standard, 800MHz Splinter, and
900 MHz bands. The scanner can scan both
conventional and trunked systems at the same time.
Feature Highlights
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Control Channel Only Scanning – If the scanner is
set to scan Motorola trunking frequencies, you can set
it so it scans using only control channel data. You do
not have to program voice channel frequencies into
memory in this mode as long as all possible control
channels are programmed.
Adaptive Digital Threshold – Automatically sets the
digital decode threshold for APCO 25 systems.
Search
Service Search – Lets you quickly select and search
the scanner’s preprogrammed frequencies.
Custom Search – Lets you program up to 10 custom
search ranges. You can search any of these ranges
simultaneously.
CTCSS/DCS Search – Lets the scanner search for
CTCSS or DCS tones. You can identify up to 50
CTCSS tones and 104 DCS tones.
Quick Search – Lets you search from the currently-
tuned frequency if you are searching a conventional
system.
Auto Store
Frequency AutoStore – Automatically stores all
active frequencies into the selected conventional
system.
Talk Group ID AutoStore – Automatically stores all
new talk group ID’s into a channel group you select.
Priority
Priority Scan – Priority channels let you keep track of
activity on your most important channel(s) while
monitoring other channels for transmissions.
Priority Plus – You can set the scanner so it scans
only the priority channels
Feature Highlights
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Backlight and Power
Display and Keypad Backlight – Makes the display
and keypad easy to see in dim light. You can adjust
the back light so it turns on when you press a key,
when squelch breaks during a transmission, or
manually.
Low Battery Alert – The scanner alerts you if the
batteries need to be recharged or replaced.
Battery Save – You can set the scanner so it reduces
the amount of power it needs if there are no
transmissions.
Key Controls
Key Lock – You can deactivate the scanner’s keys to
help prevent accidentally changing the scanner’s
programming.
PC Control and Cloning
PC Control – You can transfer programming data to
and from your scanner and your personal computer,
and control the scanner using a computer. This helps
you find frequencies listed on the Internet and load
them into the scanner. Free PC control and
programming software will be available at
the UBCD396T web page at www.uniden.com.au (for
Australia) or www.uniden.co.nz (for New Zealand).
Clone Mode – You can clone all programmed data,
including the contents of the scanner’s memory, menu
settings, and other parameters from one UBCD396T
scanner to another UBCD396T scanner.
On-Air Cloning – You can clone all programmed data
over the air from a PC to one or more UBCD396T
scanners.
Feature Highlights
12
Download from Www.Somanuals.com. All Manuals Search And Download.
About This Manual
The screen displays used in this manual are
representations of what might appear when you use
your scanner. Since what you see depends on the
frequencies and user IDs for your area and the
settings you select, you might notice some differences
between what is in this manual and what appears on
your scanner.
Using the Multifunction Scroll Control
The scroll control on top of the UBCD396T lets you
easily control channel selection, volume, and squelch,
and how information appears on the display.
To adjust menu settings, change channels in Hold
mode, and resume scanning: Simply rotate the
scroll control.
To change the scanner’s volume: Briefly press the
scroll control once, then rotate it. VOLUME LEVEL and
the current volume level appear on the display.
To adjust the squelch: While holding down
the left side of the scanner, briefly press the scroll
on
control once then rotate it. SQUELCH LEVEL and the
current squelch level appear on the display.
To change the display mode: While holding down
, briefly press the scroll control twice. Extended
receive information, usually applicable to digital
scanning, appears on the display. Then briefly press
the scroll control again to return to the original display.
Entering Text
To enter a letter, turn the scroll control until the
character you want appears, To enter a number, press
a number key. To enter a decimal point, press .
To move the cursor to the left, press < /4. To move the
cursor to the right, press 6/ > .
To clear a character, press twice. To clear all
characters, press three times.
To accept an entry, press down on the scroll control or
press E.
Feature Highlights
13
Download from Www.Somanuals.com. All Manuals Search And Download.
How the Scanner’s Controls Are
Represented in This Manual
To help navigate the scanner’s menus, the steps
shown in this manual show the displays you see and
the keys you press or control you operate to get a
desired result.
This example shows you how to use the scanner’s
menu to edit an existing system name. It shows you
the key to press (
the option you see ( Program System ) when you
press . It also instructs you to turn the scroll
control (shown as ) to view a series of choices then
) to select a menu option and
press the scroll control (shown as ) to select a
choice ( Edit Name ).
Program System
Select the system
Edit Name
Follow these steps to enter/edit the system name.
1. The first character of the system name is covered
by a cursor. Rotate the scroll control to select the
character you want.
2. Press 6/> on the keypad to select the next
character. The cursor moves to the next character.
To move the cursor to a previous character,
press </4.
Feature Highlights
14
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Repeat Steps 1 and 2 until you have entered the
system name. Then press down on the scroll
control or press E to accept the setting.
Hints:
•
Each system name can be up to 16 characters.
Abbreviate as necessary to fit.
•
The default system names include the following
letter in the 16th position to indicate the system
type:
M
E
L
C
= Motorola
= EDACS
= LTR
= Conventional
•
•
Press twice to delete the current character.
Press three times to clear the entire alpha tag.
To get the most from this manual, review the contents
to become familiar with the basic functions available.
If you are new to scanning or trunk tracking, be sure
to read “Understanding Scanning” on Page 16 for a
quick background on the technology. The first thing
you’ll need to do is install batteries in the scanner.
Then you need to connect the included antenna to the
scanner.
See “Setting Up Your Scanner” on Page 28 if you
need any help doing this.
Feature Highlights
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Understanding Scanning
Understanding Scanning This section provides you
with background on how scanning works. You don’t
really need to know all of this to use your scanner, but
some background knowledge will help you get the
most from your UBCD396T.
Understanding the Scanner’s Memory
Your scanner’s memory is organized in an
architecture called Dynamic Allocated Channel
memory. This type of memory is organized differently
and more efficiently than the bank/channel
architecture used by traditional scanners. Dynamic
Allocated design matches how radio systems actually
work much more closely, making it easier to program
and use your scanner and determine how much
memory you have used and how much you have left.
Instead of being organized into separate banks and
channels, your scanner’s memory is contained in a
pool. You simply use as much memory as you need in
the pool to store as many frequencies, talk group ID’s,
and alpha tags as you need. No memory space is
wasted, and you can tell at a glance how much
memory you have used and how much remains.
With a traditional scanner, when you program it to
track a trunked system, you must first program the
frequencies. Since you can only program one trunking
system per bank in a traditional scanner, if there were
(for example) 30 frequencies, the remaining channels
in the bank are not used and therefore wasted. Also,
since some trunked systems might have hundreds of
talk groups, you would have had to enter those types
of systems into multiple banks in order to monitor and
track all the ID’s.
What is Scanning?
Unlike standard AM or FM radio stations, most two-
way communications do not transmit continuously.
Your UBCD396T scans programmed channels until it
finds an active frequency, then stops on that
frequency and remains on that channel as long as the
transmission continues. When the transmission ends,
the scanning cycle resumes until the scanner receives
another transmission.
Understanding Scanning
16
Download from Www.Somanuals.com. All Manuals Search And Download.
What is Searching?
The UBCD396T can search 9 service search ranges
and up to 10 bands together to find active
frequencies. This is different from scanning because
you are searching for frequencies that have not been
programmed into the scanner. When you select
frequency bands to search, the scanner searches for
any active frequency within the lower and upper limits
you specify. When the scanner finds an active
frequency, it stops on that frequency as long as the
transmission lasts. If you think the frequency is
interesting, you can program it into the scanner’s
memory. If not, you can continue to search.
What is CTCSS/DCS?
Your scanner can monitor systems using a
Continuous Tone Coded Squelch System (CTCSS)
and Digital Coded Squelch (DCS) system, which allow
squelch to open only when the tone you have
programmed with a specific frequency is received
along with a transmission.
CTCSS and DCS are subaudible tone signaling
systems sometimes referred to as PL or DPL
(Motorola’s trademarked terms for Private Line and
Digital Private Line respectively). CTCSS and DCS
are used only for FM signals and are usually
associated with both amateur and commercial
two-way frequencies. These systems make use of a
special subaudible tone that accompanies a
transmitted signal.
CTCSS and DCS are used for many purposes. In
many cases, CTCSS and DCS are used to restrict
access to a commercial repeater, so that only those
units which transmit the correct tone along with their
signal can “talk” to the repeater.
Understanding Scanning
17
Download from Www.Somanuals.com. All Manuals Search And Download.
CTCSS and DCS are also used in areas that receive
interference where there are several stations with
output frequencies close to each other. When this
occurs, you might hear multiple communications on
the same frequency. The stations might even interfere
with each other to the point where it is impossible to
clearly receive any of the stations. A scanner
equipped with CTCSS and DCS (like your scanner)
can code each received frequency with a specific
CTCSS or DCS frequency. Then, when you receive
multiple signals, you only hear the transmission with
the CTCSS or DCS tone you programmed. If you do
not receive the correct tone with a signal, the
scanner’s squelch remains closed and you hear
nothing.
You can search for the following CTCSS frequencies
and DCS codes.
CTCSS Frequencies (Hz)
67.0
82.5
69.3
85.4
71.9
88.5
74.4
91.5
77.0
94.8
79.7
97.4
100.0 103.5 107.2 110.9 114.8 118.8
123.0 127.3 131.8 136.5 141.3 146.2
151.4 156.7 159.8 162.2 165.5 167.9
171.3 173.8 177.3 179.9 183.5 186.2
189.9 192.8 196.6 199.5 203.5 206.5
210.7 218.1 225.7 229.1 233.6 241.8
250.3 254.1
DCS Codes (Octal)
023 025 026 031 032 036 043 047
051 053 054 065 071 072 073 074
114 115 116 122 125 131 132 134
143 145 152 155 156 162 165 172
Understanding Scanning
18
Download from Www.Somanuals.com. All Manuals Search And Download.
174 205 212 223 225 226 243 244
245 246 251 252 255 261 263 265
266 271 274 306 311 315 325 331
332 343 346 351 356 364 365 371
411 412 413 423 431 432 445 446
452 454 455 462 464 465 466 503
506 516 523 526 532 546 565 606
612 624 627 631 632 654 662 664
703 712 723 731 732 734 743 754
Conventional Scanning
Conventional scanning is a relatively simple concept.
Each group of users in a conventional system is
assigned a single frequency (for simplex systems) or
two frequencies (for repeater systems). Any time one
of them transmits, their transmission always goes out
on the same frequency. Up until the late 1980s, this
was the primary way that radio systems operated.
Even today, there are many 2-way radio users who
operate using a conventional system:
•
•
•
•
•
Aircraft
Amateur radio
UHF/PRS users
Broadcast AM/FM/TV stations
Many business radio users
When you want to store a conventional system, all
you need to know is the frequencies they operate on.
When you are scanning a conventional system, the
scanner stops very briefly on each channel to see if
there is activity. If there isn’t, the scanner quickly
moves to the next channel. If there is, then the
scanner pauses on the transmission until it is over.
Understanding Scanning
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Simplex Operation
Simplex systems use a single frequency for both
transmit and receive. Most radios using this type of
operation are limited to line-of-sight operation. This
type of radio is frequently used at construction job
sites, and with inexpensive consumer radios such as
UHF/PRS radios. The range is typically 1-12 km,
depending upon the terrain and many other factors.
Repeater Operation
Repeater systems use two frequencies: one transmits
from the radio to a central repeater; the other
transmits from the repeater to other radios in the
system. With a repeater-based system, the repeater is
located on top of a tall building or on a radio tower that
provides great visibility to the area of operation. When
a user transmits (on an input frequency), the signal is
picked up by the repeater and retransmitted (on an
output frequency). The user’s radios always listen for
activity on the output frequency and transmit on the
input frequency. Since the repeater is located very
high, there is a very large line of sight.
Typical repeater systems provide coverage out to
about a 40-km radius from the repeater location.
What is Trunk Tracking?
Your UBCD396T is designed to track the following
types of trunking systems.
•
•
Motorola Astro (APCO 25) trunking systems.
Motorola Type I, Type II, Type IIi hybrid,
SMARTNET, and PRIVACYPLUS analog trunking
systems, which are extensively used in 800 MHz
communication systems.
•
•
•
LTR trunking systems
EDACS SCAT trunking systems
EDACS trunking systems
Understanding Scanning
20
Download from Www.Somanuals.com. All Manuals Search And Download.
When tracking these types of systems, you might
want to remember that your scanner can track more
than one trunking system at a time and scan
conventional and trunked systems at the same time.
Conventional scanning is a simple concept. You enter
a frequency used by someone you want to monitor
into your scanner’s memory. For example, the police
in your area might transmit on 460.500 MHz, the fire
department on 154.445 MHz, the highway department
on 37.900 MHz, etc. So when your scanner stops on a
frequency, you usually know who it is, and more
importantly, you can stop on a channel and listen to
an entire conversation. This type of scanning is easy
and fun.
However, as the demand for public communications
has increased, many public radio users do not have
enough frequencies to meet their needs, creating a
serious problem. Trunking radio systems help solve
this problem.
Trunked Scanning
While conventional scanning worked great while there
were only a few groups wanting to use the
frequencies, with the advent of smaller, lower-cost
radios more and more agencies and businesses
wanted to take advantage of the utility of 2-way radio.
As a result, the bands that were used most became
full, so new users were not able to take advantage of
the technology as quickly as they wanted.
Trunking solved this frequency shortage by allowing
multiple groups to use the same set of frequencies in
a very efficient way. While each type of trunking
system operates a little differently (see the next few
sections), they all work on the same basic premise:
even in a system with a lot of users, only a few users
are ever transmitting at any one time.
Instead of being assigned a frequency, as with
conventional systems, each group is assigned a talk
group ID. A central computer controls the frequency
Understanding Scanning
21
Download from Www.Somanuals.com. All Manuals Search And Download.
each group operates on...and this frequency selection
is made each time a user transmits. So, while on a
conventional system queries, replies, and follow-ups
are all on a single frequency, they could each be on
completely different frequencies on a trunked system.
This semi-random frequency assignment made
monitoring such a system impossible prior to Uniden’s
invention of the TrunkTracker scanner.
Not only does your UBCD396T scan channels like a
conventional scanner, it actually follows the users of a
trunked radio system. Once you know a talk group’s
ID, you won’t miss any of the action.
If you are a new scanner enthusiast, you might want
to read the first part of this manual and use your
scanner in conventional mode before you begin trunk
tracking. Understanding scanning fundamentals and
terminology will make trunk tracking much easier. If
you are already an experienced scanner operator, you
might want to go to “Programming Motorola Systems”
on Page 59, “Programming EDACS Systems” on
Page 63, or “Programming LTR Systems” on Page 66
now.
Types of Trunking Systems
Trunking systems divide a few frequencies among
many different users, but the way that each system
does this is slightly different. This section describes
some of the technical data behind Motorola, EDACS,
and LTR trunked radio systems.
Motorola Trunking
While there are different types of Motorola trunking
systems, they all use the same basic trunking method.
The system consists of one control channel (or as
many as 4 per system but only one is active at any
one time), plus one or more voice channels (typically
10, 20, or 28 total channels). When a user presses
Push To Talk (PTT) to transmit, their radio first sends
their talk group information to the control channel.
Understanding Scanning
22
Download from Www.Somanuals.com. All Manuals Search And Download.
The computer then assigns that talk group to a
specific voice channel and transmits that data over the
control channel. All radios in that talk group switch
over to the assigned voice channel and the user can
begin speaking.
This all typically takes place in about a second...
the person transmitting hears a beep from their
radio when the channel is assigned and then it is OK
to start talking.
The systems in use are:
Motorola Type I – the radios send the radio ID, the
fleet and subfleet talk group ID to the control channel
each time they transmit. To program a Type I system,
you need to know the system’s fleet map. The most
common fleet maps are included in “Preset Fleet
Maps” on Page 123. You can also find fleet map
resources on the web.
Motorola Type II – the radios only send the radio ID
and radio channel code to the control channel. The
central computer keeps a database of radio ID’s and
which talk group is assigned to which channel code
for each radio, so with this system the user’s radio
sends only about 1 /3 the data as a Type I system with
each transmission. Type II systems do not use Fleet-
subfleet talk groups; instead they use a 5-digit ID for
each talk group.
Type IIi Hybrid — these systems support a mix of
both Type I and Type II users. Like Type I systems,
you must know the system’s fleet map to ensure
proper tracking.
Motorola ASTRO 25 (APCO 25) – these radios are
similar to Type II systems, but send only the radio ID
and radio channel code to the control channel, trans-
mitting voice in digital form.
Understanding Scanning
23
Download from Www.Somanuals.com. All Manuals Search And Download.
EDACS Trunking
EDACS trunking works in much the same way as
Motorola trunking with a couple of major differences.
In an EDACS system, each frequency used by the
system is assigned a Logical Channel Number (LCN)
so that less data needs to be transmitted by the
control channel. Also, talk groups are assigned in an
Agency-Fleet-Subfleet (AFS) hierarchy. Also, there is
one variation of EDACS called SCAT that your
UBCD396T can monitor.
Logical Channel Numbers – each frequency used by
the system is assigned an LCN. This information is
programmed into each user radio. When a user
presses PTT, their radio sends their AFS information
to the control channel. The computer then assigns
that talk group to a channel and sends the LCN so
that all other radios in that talk group will switch to the
correct channel. To program an EDACS system in
your scanner, you will need to know both the
frequencies used by the system and the LCN for each
frequency.
Agency-Fleet-Subfleet – talk group ID’s for EDACS
systems are assigned in a way that makes it easy to
see at a glance the affiliation of the user. Each radio is
assigned a 2-digit agency identifier from 00 – 15.
For example, 01 might be used by the police, 02 by
the ambulance service, 03 by the fire department, and
so on. Each agency is then subdivided up to 16 times
to provide fleet identification, and then 8 more times to
identify subfleets.
For example, the complete AFS for the Police
Department West District’s dispatch channel might be
01-062. 01 identifies the agency as the police
department, 06 identifies the fleet as the West district,
and 2 identifies the subfleet as the dispatch channel.
While these assignments are somewhat arbitrary and
vary from system to system, there are many
resources on the web for finding the assignments for
most systems. Because of the logical hierarchy of the
AFS system, your UBCD396T lets you assign
wildcard ID’s that let you, for example, use only one
ID memory to identify all units in either an agency or a
Understanding Scanning
24
Download from Www.Somanuals.com. All Manuals Search And Download.
EDACS SCAT – EDACS SCAT (Single Channel
Autonomous Trunking) systems operate on a single
channel and alternate control data with analog voice
traffic. While your UBCD396T cannot track ID’s in this
system, it can eliminate the control data so that all you
hear is the voice transmissions when you monitor this
type of system.
LTR Trunking
LTR (Logic Trunked Radio) systems are trunking
systems used primarily by business or private
communications service providers, such as taxicabs,
delivery trucks, and repair services. These systems
encode all control information as digital subaudible
data that accompanies each transmission, so there is
no separate control channel. Users on an LTR system
are assigned to specific talk groups, which are
identified by the radio as six digit numbers.
These numbers are in the form AHHUUU, where:
A = Area code (0 or 1)
H = Home repeater (01 through 20)
U = User ID (000 through 254)
When the scanner receives a transmission on a
channel set to the LTR mode, it first decodes the LTR
data included with the transmission. In the ID search
mode, the scanner stops on the transmission and
displays the talk group ID on the display. In the ID
scan mode, the scanner only stops on the
transmission if the LTR data matches a talk group ID
that you have stored in the talk group ID list and have
not locked out.
LTR systems are frequently programmed so that each
radio has a unique user ID.
Understanding Scanning
25
Download from Www.Somanuals.com. All Manuals Search And Download.
I-Call (Motorola/EDACS)
I-calls are direct unit-to-unit transmissions that are not
heard by other system users. Your UBCD396T can
receive I-call transmissions. See “Setting I-Call
(Motorola and EDACS Systems Only)” on Page 77 for
more information about monitoring I-call
transmissions.
Where To Get More Information
By itself, this manual only provides part of what you
need to know to have fun scanning – how to
program and use the scanner. Other sources provide
additional information.
Information On The Internet
The Internet is a great source for current frequencies
and information about scanning. Many web sites have
lists of frequencies for your area. You can use a
search engine to find and use them.
Make a list of the agencies you want to listen to, then
look up the frequencies and systems used by those
agencies. Here are a few useful sites:
For Australia visit www.uniden.com.au, select any
scanner product then click on "Scanner Frequency".
For New Zealand visit www.nzscanners.org.nz
For more information about Uniden and our
products, visit www.uniden.com.au (Australia) or
www.uniden.co.nz (New Zealand).
Understanding Scanning
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Included With Your Scanner
Connection
Cable
Wrist Strap
AC Adaptor
Batteries
Scanner
(with antenna
attached)
Belt Clip
UBCD396T
Owners Manual
OWNER'S MANUAL
BNC/SMA Adaptor
Owners
Manual
and other
printed
material
If any of these items are missing or damaged,
immediately contact your place of purchase.
Included With Your Scanner
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Up Your Scanner
These guidelines will help you install and set up your
new scanner:
• If your scanner receives interference or electrical
noise, move the scanner or its antenna away from
the source.
• To improve the scanner’s reception, use an
optional external antenna designed for multi-band
coverage. (You can purchase this type of antenna
at a local electronics store). If the optional antenna
has no cable, use 50-75W coaxial cable for
lead-in. A mating plug might be necessary for the
optional antennas.
• Use an optional mono earphone or mono headset
with proper impedance (32 W) for private
listening.
Read the precautions on the inside front cover of
this Owners Manual.
• Do not use the scanner in high-moisture
environments such as the kitchen or bathroom.
• Avoid placing the scanner in direct sunlight or near
heating elements or vents.
Using Internal Batteries
You can power your scanner using three alkaline or
rechargeable AA batteries.
Before installing batteries, set the switch in the battery
compartment to match the type of batteries you will
use. Select ALKALINE for non-rechargeable battery
types and Ni-MH for rechargeable battery types. See
also “Using Rechargeable Batteries” on Page 29
when you use rechargeable batteries.
1. Remove the battery cover and set the battery
switch.
Setting Up Your Scanner
28
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Install 3 AA batteries,
matching the polarity
symbols (+ -).
WARNING!
Set ALKALINE/Ni-MH to Ni-MH for use only with
rechargeable batteries. Never attempt to recharge
non-rechargeable batteries. Non-rechargeable
batteries can get hot and can even burst if you try
to recharge them.
3. Replace the cover.
When flashes and the scanner beeps every 15
seconds, replace the batteries.
Using Rechargeable Batteries
You can also use three rechargeable batteries to
power your scanner. Before you use rechargeable
batteries, you must charge them. The scanner has a
built-in circuit that lets you recharge batteries while
they are in the scanner. To charge the batteries, set
ALKALINE/ Ni-MH inside the battery compartment to
NI-MH, install the batteries in the scanner, and
connect the supplied AC adaptor to the scanner's DC
6V jack (see “Using AC Power” on Page 30).
WARNING!
Do not connect the AC adaptor to the scanner if
non-rechargeable batteries (such as alkaline
batteries) are installed in the scanner and
ALKALINE/Ni-MH is set to NI-MH, or if you are
unsure of the switch's position. Non-rechargeable
batteries can get hot and can even burst if you try
to recharge them. Before you use rechargeable
batteries for the first time, charge them for 14
hours to bring them to a full charge. Discharged
batteries take about 14 hours to fully recharge.
Setting Up Your Scanner
29
Download from Www.Somanuals.com. All Manuals Search And Download.
If an AC adaptor is connected to the scanner, the
scanner checks the condition of the installed batteries.
If the scanner is turned off and the batteries require a
full charge, Pre-Charging appears on the display.
Then, Normal Charging appears as the batteries
are recharged. When the batteries are fully charged,
Charge Complete appears.
If no batteries are installed in the scanner, No
Battery appears. If there is a problem with the
installed batteries, Battery Error appears. If the
installed batteries are Ni-MH batteries but
ALKALINE/Ni-MH is set to ALKALINE, Charge Off
appears and the scanner does not charge the
batteries.
Removing the Display Sticker
Before you use the scanner, remove the protective
plastic sticker over the display.
Using AC Power
You can power the scanner using the supplied 6V,
800 mA AC adaptor.
To use the scanner on
AC power, plug the
adaptor into 6V 800 mA
on the right side of the
scanner, then plug the
AC adaptor into a
standard AC outlet.
If rechargeable batteries are installed and ALKALINE/
Ni-MH is set to NI-MH, the adaptor powers the
scanner and recharges the installed batteries at the
same time.
WARNING!
To prevent damage to Ni-MH batteries, never
charge them in an area where the temperature is
above 113°F (45°C) or below 32°F (0°C).
Setting Up Your Scanner
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the Antenna
To attach the supplied flexible antenna to the
connector on the top of your scanner, simply screw it
onto the scanner's SMA connector.
Connecting an Optional Antenna
The scanner's SMA connector makes it easy to
connect a variety of optional antennas, including an
external mobile antenna or outdoor base station
antenna.
Note: Always use 50- or 75-ohm, RG-58, or RG-8,
coaxial cable and the supplied BNC/SMA adaptor to
connect an outdoor antenna. If the antenna is over 15
metres from the scanner, use RG-8 low-loss dielectric
coaxial cable. Cable loss increases with higher
frequency.
Connecting an Earphone/Headphone
For private listening, you can plug a 1 /8-inch (3.5mm)
mini-plug earphone or headphones (not supplied) into
the headphone jack on top of your scanner. This
automatically disconnects the internal speaker.
See “Earphone Warning” at the front of the manual for
important information about using an earphone/
headphone.
Connecting an Extension Speaker
In a noisy area, an optional amplified extension
speaker, positioned in the right place, might provide
more comfortable listening. Plug the speaker cable's
1/8-inch (3.5-mm) mini-plug into your scanner's jack.
WARNING!
Never connect anything other than an earphone or
the recommended amplified extension speaker to
the scanner’s headphone jack. This might damage
the scanner.
Setting Up Your Scanner
31
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING!
Never connect any part of the headphone jack to
the antenna jack or connect the radio to an
installation where the antenna and audio
connection are grounded. This might damage the
scanner.
Attaching the Belt Clip
To make your scanner easier to carry when you are
on the go, use the supplied belt clip. Rotate the
scanner upside down to remove it from the clip.
Attaching the Wrist Strap
To keep your scanner safely close at hand, use the
supplied wrist strap. Push the small loop on one end
of the wrist strap through the lug on the right side of
the scanner, then thread the other end of the wrist
strap back through the small loop to secure it.
A Look At The Keypad
Your scanner's keys have various functions labeled on
the key tops and below the keys.
To select the function labeled on a key, simply press
the key. To select the function labeled below a key,
hold down
press the key.
on the left side of the scanner then
appears on the display.
Setting Up Your Scanner
32
Download from Www.Somanuals.com. All Manuals Search And Download.
If your scanner's keys seem confusing at first, the fol-
lowing information should help you understand each
key's function.
Key Name
Hold/
Description
Hold – Holds the scan or the
frequency search when pressed.
Resumes the scan or the
frequency search when pressed
again.
+
– Quickly turns the
Close Call feature on or off (see
"Setting Close Call Options” on
Page 101).
Scan/srch
Scan – Scans the stored
channels.
+ srch – Starts quick search
or quickly accesses the
search menu.
L/O
L/O – Lets you lock out a
selected channel or skip a
specified frequency.
Press and hold for more than 2
seconds to unlock all channels
in a system or all frequencies in
a Search mode. Lets you also
exit a menu.
+ L/O – Press quickly to lock
and unlock a selected system in
Scan or Scan Hold mode and
review search lockout
frequencies in Search or Search
Hold mode.
Setting Up Your Scanner
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Key Name
Description
/
/
– Turns the display
backlight on or off.
Press and hold for more than
2 seconds to turn the scanner
on or off.
+ – Locks and unlocks
the keypad.
1-9, 0
1-9, 0 – Enters a frequency,
enters quick key numbers,
and selects a custom search
range in Custom Search
mode.
Selects systems by quick key
in scan mode.
+ 1-9, 0 – Selects groups
by quick key in scan mode.
1/pri
</4
1 – Enters a 1.
+ pri – Selects the priority
mode in scan hold mode.
4 – Enters a 4.
+ > – Moves the active
character to the left while
editing data.
6/>
6 – Enters a 6.
+ > – Moves the active
character to the right while
editing data.
Setting Up Your Scanner
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Key Name
7/rcl
Description
7 – Enters a 7.
+ rcl – Displays a series of
prompts to quickly select a
specific channel in the scan hold
mode.
no/rev
– Enters a decimal point or
dash in a frequency or talk
group ID, enters or selects an
extended 2-digit Quick Key,
enters an “i” for I-Call input.
At a prompt, answers “No.”
+ rev – Monitors the
currently-tuned frequency’s
reverse frequency.
E/yes/att
E – Press to select input and
menu items, to quickly edit a
channel in Scan Hold Mode, and
store a frequency into memory
in Scan Hold mode.
At a prompt, answers “yes.”
+ att – Turns the scanner’s
attenuator on or off for the
current channel (for
conventional systems) or
system (for trunked systems).
A Look At The Display
The display has indicators that show the scanner's
current operating status. The display information helps
you understand how your scanner operates.
Sn: - appears with a number to show the currently-
selected System Quick Key number. n appears to
show the first digit of the Quick Key number.
For example, if System Quick Key 75 is selected, S7:
appears. The currently active system indicator
flashes.
Setting Up Your Scanner
35
Download from Www.Somanuals.com. All Manuals Search And Download.
ATT - appears when the attenuation feature is
turned on. See “Setting System Attenuation
(Trunked Systems Only)” on Page 81.
PRI - appears when the priority feature is turned on
(see “Priority Scan” on Page 50).
- appears when you lock the keypad (see
“Locking/Unlocking the Keypad and Scroll” on
Page 49).
- alerts you when the battery power gets low.
GRP - shows the currently activated group or
selected group Quick Key number, appears
with numbers ( 0 - 9 ).
The currently active group indicator flashes.
AM / FM / NFM / WFM - appears to show the type
of transmission.
L/O - appears when you manually select a channel
you locked out or a skip frequency.
- appears when you hold down
function.
to select a
- appears when the scanner is set to a Close
Call feature mode (see “Using the Close Call
Feature” on Page 100).
SCAN - scrolls while the scanner is scanning.
DSKP - appears when data skip is turned on.
HOLD - appears while the scanner is set to scan or
search hold mode.
- appears if priority is turned on
ATT - appears if the attenuator is turned on.
SCR - appears when one or more broadcast screen
bands are turned on.
REP - appears when repeater find is turned on.
P25 - appears when an APCO P25 digital voice
transmission is being received.
- appears to show signal strength (0 to 5)
Setting Up Your Scanner
36
Download from Www.Somanuals.com. All Manuals Search And Download.
LNK - appears when data on a voice channel is
being received.
DAT - appears when data on a control channel is
being received.
ENC - appears when APCO P25 encrypted data is
being received on a voice channel.
Using Menu
Press
on the left side of the scanner to enter the
menu. See “Using the Menu” on Page 45 for more
information about the scanner’s menu options.
Using Func
To select the function labeled below a key on the front
of the scanner, hold down
on the left side of the
scanner, then press that key. To hold on a system
while scanning or temporarily stop on a channel while
searching, press . To select a system in Scan or
Scan Hold mode, hold down and rotate the scroll
control.
Setting Up Your Scanner
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operation
Turning On the Scanner and Setting the
Squelch
Note: Make sure the scanner's antenna is connected
before you turn it on.
1. Press and hold
the scanner.
for about 2 seconds to turn on
2. Briefly press the scroll control
once. VOLUME LEVEL and a
number appear on the display.
Brisbane
3. While VOLUME LEVEL appears, rotate the scroll
control to set the volume to a comfortable listening
level.
Note: If you do not press any key or turn the scroll
control within about 10 seconds, VOLUME LEVEL
disappears. If this happens, simply press the
scroll control again.
4. While holding down
on the left side of the
scanner, briefly press the scroll control once.
SQUELCH LEVEL and a number appear on the
display.
5. While SQUELCH LEVEL appears, rotate the scroll
control to set the squelch to the level you want.
Note: If you do not press any key or turn the scroll
control within about 10 seconds, SQUELCH LEVEL
disappears. If this happens, briefly press the scroll
control while holding down
.
Basic Operation
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Scanning Systems
To begin scanning programmed systems, press Scan.
The UBCD396T scans all unlocked systems in all
activated quick-key groups and any searches
unlocked for search and scan.
Notes:
• If no systems are programmed, or all systems are
locked out, an error message appears. Program a
system or select a system to scan.
• When scanning multiple systems, the UBCD396T
scans systems according to the assigned quick
key. Systems assigned to quick key 1 are
scanned first, then 2, 3, 4, etc. Systems not
assigned to a quick key are scanned last, then
unlocked searches. Within a quick key, systems
are scanned in the order they were assigned.
• Within a system, channels are scanned according
to the assigned channel group, with the same
priority as described above for systems.
• The UBCD396T scans a system for the duration
you set using the System Hold Time option (see
“Setting the System Hold Time” on Page 72). For
trunked systems, the scanner moves to the next
system after the hold time expires, the current
transmission ends, and the channel delay expires.
Conventional systems operate similarly, but all
unlocked channels are scanned at least one time
regardless of the hold time setting.
• Each search range is searched for the amount of
time you set using the “Set Hold Time” option.
See “Setting the System Hold Time” on Page 72
for more information.
Basic Operation
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting Systems to Scan
To select systems to scan, press Scan then press the
quick key assigned to the system or systems you want
to scan. For quick keys 0-9, press the quick key’s
number. For quick keys 10-99, press then press the
quick key’s 2-digit number. To stop scanning the
system(s), press (if the quick key is a 2-digit quick
key) then the number button or buttons again.
The Sx: (system) indicators on the display show the
systems that are currently selected.
Basic Operation
40
Download from Www.Somanuals.com. All Manuals Search And Download.
To select or lock out a system that is not assigned to a
key, press and hold while you rotate the scroll
control until the desired system is selected. Then,
continue to hold
or unlock the system.
and press L/O to either lock out
Selecting System Channel Groups
Within a system, you can assign groups of channels
to a group quick key (see “Setting the Group Quick
Key” on Page 83).
Follow these steps to activate or deactivate a channel
group within a system while scanning.
1. Press to hold
then rotate the scroll control to select the
system).
on the system (or hold down
2. Continue to hold
and press the number key
corresponding to the channel group you want to
activate or deactivate.
Locking/Unlocking Systems
Follow these steps to lock out a system so that it does
not scan even if its quick key is selected.
1. While holding down
to select the system.
, rotate the scroll control
2. Continue to hold down and press L/O to lock
out the system. System Locked appears.
3. Repeat Steps 1 and 2 to unlock a system you
have previously locked. System Unlocked
appears.
Locking/Unlocking Channels
Follow these steps to lock out a channel so that it
does not scan even if its system and channel group
are selected.
1. While holding down , rotate the scroll control
to select the system where the channel is stored.
Basic Operation
41
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Release then press Hold within 2 seconds
to hold on the system.
3. Rotate the scroll control to select the channel you
want to lock or unlock.
4. Press L/O to lock or unlock the channel.
You can also lock out an active channel by pressing
L/O while the scanner is stopped on the channel.
ID Scan/ID Search Mode
While you are scanning a trunked system, the scanner
can be in either ID Scan or ID Search mode:
• ID Scan – the scanner only stops on talk group
ID’s that you have programmed into the system
• ID Search – the scanner stops on any unlocked
talk group that becomes active.
To toggle between ID Scan and ID Search, press
then press Scan within 2 seconds while the scanner is
scanning the system.
If the scanner does not scan the system long enough
while the scanner
then rotate the
for you to easily do this, press
is scanning the system (or press
scroll control to select the system). Then, release
and press Scan within 2 seconds.
Temporarily Holding On a System
To temporarily hold on a system, press and hold
To hold on a different system, continue to hold
and rotate the scroll control to select the system.
Normal scanning resumes 2 seconds after you
.
release
.
Holding On a Channel
To hold on a channel, press Hold while the channel is
active. To select a different channel, rotate the scroll
control. If you scroll past the beginning or end of the
current system, the scanner selects channels in the
Basic Operation
42
Download from Www.Somanuals.com. All Manuals Search And Download.
previous or next system. To resume scanning, press
Scan.
Quickly Storing an ID During ID
Search
To quickly store an active talk group ID during ID
search, press E. You see:
Quick TGID Save?
To save the ID into a channel, press E. Otherwise,
press . If you press E, the scanner stores the ID into
a channel group called Qck Save Grp in the
current system.
Quick-Storing Channels or Talk Group
ID’s
1. Hold on an existing channel in any system.
2. Enter the frequency or talk group ID you want to
store (press twice to enter hyphens in talk group
ID’s).
3. To quick-store the channel or talk group ID, press
E. Otherwise, press
.
If you enter a frequency then press E, the scanner
stores it in the Qck Save Grp group in a system
called Qck Save Cnv Sys . These are created if
they
do not exist. Then, the scanner prompts you to save
other channel settings.
If you enter a talk group ID then press E, the scanner
stores it into a channel group named Qck Save Grp
in the current system. If the talk group ID’s format is
not the type used by the current system, the scanner
displays an error message and does not save the talk
group ID.
Basic Operation
43
Download from Www.Somanuals.com. All Manuals Search And Download.
If you pressed No in Step 3, the scanner prompts you
to select the system and the group where you want to
store the frequency or talk group ID.
Quickly Recalling Channels
1. Press Hold to hold on any channel.
2. Press + Rcl. The scanner prompts you to
select the system where the channel is stored.
3. Rotate the scroll control to select the system, then
press E. The scanner prompts you to select the
channel group where the channel is stored.
4. Rotate the scroll control to select the group, then
press E. The scanner prompts you to select a
channel.
5. Rotate the scroll control to select the channel,
then press E to hold on that channel.
Monitoring Trunking Activity
To monitor trunking activity, press Hold then turn the
scroll control to select the control channel frequency
(for a Motorola or EDACS system) or any system
frequency (for an LTR system). Active talk group ID’s
appear on the second line of the display. For Motorola
systems, the scanner will show the System ID on the
top line of the display. For EDACS systems, the
scanner will show the site ID on the top line of the
display.
Toggling Channel Alpha Tags
To change the display so the channel and frequency
or Talk Group ID appear instead of the alpha tag,
press
+ 5.
Basic Operation
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Using The Menu
The scanner’s menu lets you select options that let
you set up and use the scanner.
To use the menu, press
on the left side of the
scanner. To select a menu item, rotate the scroll
control clockwise or counterclockwise. The currently-
selected menu item is highlighted with a bar on the
display. When the menu item you want to select is
highlighted, briefly press the scroll control to select it.
To back up a level, press . To exit the menu
mode, press again or the L/O key.
This table shows the scanner’s menu structure. To
find information about a particular menu setting in this
manual, go to the page number shown in parentheses
next to the setting.
Note: Not all of the options shown in this table may
appear at the same time. To view all available options
on any screen, rotate the scroll control.
47
New System
104
105
92
106
107
109
88 107
107
108
109
79
91
95
93
94
97
Note: the actual Select System submenu display will depend on
what is programmed into the scanner.
Using the Menu
45
Download from Www.Somanuals.com. All Manuals Search And Download.
101
101
101
101
101
101
50
50
50
50
114
114
53
54
50
49
50
51
51
52
49
Using the Menu
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming Systems Menu
This table shows the scanner’s systems menu
structure. This menu lets you program new systems or
change existing systems. To find information about a
particular menu setting in this manual, go to the page
number shown under or next to the setting.
To use the systems menu, press then briefly
press the scroll control. To back up a level, press
.
To exit the menu mode, press
[L/O].
again or press
Note: Not all of the options shown in this table may
appear at the same time. To view all available options
on any screen, rotate the scroll control.
70
71
57
81
81
70
71
67
61
80
62
81
81
70
71
67
80
62
81
81
Using the Menu
47
Download from Www.Somanuals.com. All Manuals Search And Download.
70
71
67
61
80
67
81
81
Using the Menu
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Other Settings
Displaying System Information
Viewing Memory Used
Settings
See Scanner Info
% Memory Used
A bar showing the percent of memory used appears.
Press any key to return to the previous menu.
Viewing the Firmware Version
Settings
See Scanner Info
Firmware Version
Press any key to return to the previous menu.
Adjusting the Key Beep
Settings
Adjust Key Beep
Auto - the scanner automatically sets the key beep to
match the master volume setting level you select.
Level 1 - 15 the scanner lets you select a key
beep level. You can choose any of 15 different key
beep levels.
Off - the scanner turns the key beep off.
Locking/Unlocking the Keypad and
Scroll
Press and hold
down then press
/
/
to
lock or unlock the keypad. Keypad Lock and On (if
the keypad is locked) or Off (if the keypad is
unlocked) appears. This does not affect the volume
setting. The scroll control still controls the volume
when you lock the controls.
Other Settings
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Turning Power Save On or Off
Settings
Set Battery Save
•
•
On The scanner goes into low-power mode when
you monitor a conventional channel that has no
activity.
Off Power save is off.
Priority Scan
Set Priority
Or, while holding on any channel, press
to select one of these priority modes:
+ 1/Pri
•
•
Off Normal scanning
On While scanning a conventional system, the
scanner interrupts every 2 seconds and checks
the priority channels in each unlocked
conventional system. Priority channels in lower
priority key numbered systems (starting from 1)
have highest priority. PRI appears when you
select this mode.
•
Plus On The scanner only scans priority
channels in unlocked conventional systems.
PRI flashes when you select this mode.
Using the Backlight
Settings
Set Backlight
•
•
•
10 sec The backlight stays on for 10 seconds
after you press
.
30 sec The backlight stays on for 30 seconds
after you press
.
Squelch The backlight turns on when the
squelch opens then stays on for 5 seconds.
Other Settings
50
Download from Www.Somanuals.com. All Manuals Search And Download.
•
•
Keypress The backlight turns on when any key
is pressed then stays on for 10 seconds.
Infinite The backlight turns on when you
press
then stays on until you press
again.
Pressing any key while the backlight is on extends the
backlight period. Pressing
turns off the backlight.
while the backlight is on
Setting the Audio AGC
Settings
Set Audio AGC
This setting helps balance the audio level you hear as
you listen to different radio sources so you can hear
them at a similar volume. Use this setting if you listen
to an audio source that has natural changes in audio
level for which you want to compensate.
Analog Rotate the scroll control to select. This
setting lets you set the audio AGC for receiving analog
channels.
•
•
On Press the scroll control to select. Audio AGC is
turned on.
Off Press the scroll control to select. Audio AGC
is turned off.
Digital Rotate the scroll control to select. This
setting lets you set the audio AGC for receiving digital
channels.
•
On Press the scroll control to select. Audio AGC is
turned on.
•
Off Press the scroll control to select. Audio AGC
is turned off.
Adjusting the Display Contrast
Settings
Adjust Contrast
Contrast 1 - 15 the scanner adjusts the display
to the contrast level you select.
Other Settings
51
Download from Www.Somanuals.com. All Manuals Search And Download.
This setting controls the display’s contrast (how light
or dark it appears). Use this setting to change the
contrast for different viewing conditions. There are 15
contrast settings. You see the change in contrast as
you scroll through the settings.
Initializing the Scanner’s Memory
Important! This clears data you have entered. You
cannot restore user programmed data that has been
deleted.
To initialize the scanner’s memory, turn off the
scanner. Then, press 2, 9, and Hold while turning it
on.
You can restore factory programmed data when you
next see:
Restore Preprogram List? Press “E yes” for
Yes or “.” for No.
Connecting Your Scanner to a Personal
Computer
To connect your scanner to a personal computer, you
must first set the scanner’s baud rate (the rate at
which data is transferred between the scanner and the
computer, in bits per second (bps).
Important! Before you start transferring data between
your scanner and your computer, make sure the
batteries are fresh or fully charged. If the scanner
loses power while you are transferring data, its
memory might be corrupted and all information
programmed in the scanner might
be erased.
Hint: If you have trouble transfer-
ring data between your scanner
and your computer, try setting the
baud rate to a slower setting.
Other Settings
52
Download from Www.Somanuals.com. All Manuals Search And Download.
Use the included connection cable to connect your
scanner to another UBCD396T scanner or your
personal computer.
Settings
PC Control
PC Control Lets you set the baud rate your scanner
uses to communicate with a personal computer.
•
•
•
•
•
•
Off The baud rate is not set.
9600 bps The baud rate is set to 9600 bps.
19200 bps The baud rate is set to 19,200 bps.
38400 bps The baud rate is set to 38,400 bps.
57600 bps The baud rate is set to 57,600 bps.
115200 bps The baud rate is set to 115,200 bps.
Using the Cloning Options
Lets you set your scanner as a master (source) or
slave (recipient), letting you transfer programming to
or from another UBCD396T scanner. See "Wired
Cloning" on Page 53 (below) and "On-Air Cloning" on
Page 54.
Wired Cloning
Xfer Information
Wired Clone
•
Master Sets the scanner to be the source
scanner.
•
Slave Sets the scanner to be the recipient
scanner.
To clone (copy) data directly from one UBCD396T
scanner to another UBCD396T scanner, you must
first connect the scanners to each other using the
included connection cables and a DB9 null modem
adaptor and DB9 gender changer (neither
included), available at most computer stores. Then
you must set one scanner as the source and the
other as the destination.
Plug the smaller end of each of the included
connection cables into Remote on the right side of
each scanner. Then connect the other end of the
cables together using the null modem connector
and gender changer.
Other Settings
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Then set the scanner containing the programming you
want to transfer as the master scanner, then set the
other scanner as the slave scanner.
(Master scanner) Clone Master Press SCAN Key
(Slave scanner) Clone Slave Press SCAN Key
When you are ready to clone the scanner, press
on the slave scanner first, then on the master scanner.
The master scanner checks the connection between
the two scanners, then transfers its data to the slave
scanner.
When the transfer is complete, Complete appears on
both scanners. If the transfer did not work, Error
appears on the master scanner.
On-Air Cloning
You can clone (copy) data from a PC to a UBCD396T
scanner. This is useful if you want to quickly program
20 or more UBCD396T scanners at the same time.
Note: On-air cloning is practical if you are
programming more than 10 scanners at the same
time. Otherwise, we recommend you use wired
Programming.
Xfer Information
On-Air Clone
•
•
Start Cloning Start on-air cloning.
Set Frequency Lets you set the frequency where
your scanner receives the cloning broadcast.
Set Modulation Lets you set the cloning
broadcast’s modulation type.
•
To clone (copy) data from a PC to the scanner, you
need a transceiver, a PC that has an audio input, and
a cable to connect your PC’s sound card to the
transceiver. Follow the directions supplied with the
Uniden Advanced Scanner Director Software
(available online at www.uniden.com.au (for Australia)
or www.uniden.co.nz (for New Zealand)) to construct
a cable and use on-air cloning.
Other Settings
54
Download from Www.Somanuals.com. All Manuals Search And Download.
When you are receiving the cloning broadcast and are
ready to clone the scanner, select Start Cloning
on the scanner. The scanner receives the data from
the transmission
When the transfer is complete, Complete appears. If
the transfer did not work, Error appears.
Other Settings
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming Radio Systems
To get the most out of your UBCD396T you can
organize frequencies into programmed radio systems.
Programming radio systems is completed in two major
steps. Don't skip either step!
1. Plan the system.
2. Program the system into your scanner according
to the plan you prepared in Step 1.
To make planning easier, planning worksheets are
included in the back of this manual for each system
type. Copy the worksheets (or download this manual
from the Uniden website and print extra sheets), then
use them to plan out how you will program the
scanner.
Important! Before you start programming your
scanner, make sure the batteries are fresh or fully
charged. If the scanner loses power while you
program it, its memory might be corrupted which will
require you to reinitialize it (see "Initializing the
Scanner’s Memory" on Page 52). All information
programmed in the scanner, including
preprogrammed systems, might be lost.
General Notes
•
•
You can store up to 400 systems.
Trunking systems can have up to 200 channels
Each. The number of conventional system
channels you can have is limited only by the
amount of scanner memory remaining.
You can store up to 20 channel groups per system.
Total channels are limited to about 6000 (3000 is
Typical).
•
•
Programming Radio Systems
56
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming Conventional Systems
Program System
New System
Conventional
Confirm? Yes=”E” / No=”.”
The scanner creates an empty conventional system,
with a default name of System n
C.
n is a number that increments as you add new
systems. C indicates that this is a conventional
system.
Refer to the appropriate section to set system-wide
options:
•
•
•
•
•
•
•
•
See "Editing the System Name" on Page 70
See “Editing the System Quick Key” on Page 71
See “Setting System Lockout” on Page 71
See “Setting the System Hold Time” on Page 72
See “Setting the Channel Delay Time” on Page 72
See “Deleting Systems” on Page 81
See “Copying Systems” on Page 81
See “Entering/Editing Conventional Channel
Groups” on Page 57(below)
Entering/Editing Conventional
Channel Groups
To enter channels in a conventional system, first set
up a channel group (or groups) to hold the channels.
Then, enter the channel and channel parameters in
the group(s).
Setting Up a Channel Group
Program System
Select the system
Edit Group
New Group
Programming Radio Systems
57
Download from Www.Somanuals.com. All Manuals Search And Download.
The scanner creates a group with a default name of
Group n. n increments by one for each new group
you create within a system. Refer to the appropriate
section to set group-wide options:
•
See “Entering/Editing the Group Name” on
Page 82
•
•
•
•
See “Setting the Group Quick Key” on Page 83
See “Deleting Groups” on Page 83
See “Setting System Lockout” on Page 71
See “Entering/Editing Conventional Channels” on
Page 58 (below)
Entering/Editing Conventional Channels
Program System
Select the system
Edit Group
Select the group
Edit Channel
New Channel
Refer to the appropriate section to change a channel
Setting:
•
•
See “Editing the Channel Name” on Page 84
See “Editing Frequencies (Conventional Channels
Only)” on Page 85
•
See “Setting Channel Priority (Conventional
Channels Only)” on Page 85
•
•
See “Deleting Channels” on Page 90
See “Copying/Pasting Channels” on Page 90
Note: The scanner automatically sets the step to
match the input frequency.
Programming Radio Systems
58
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming Motorola Systems
Program System
New System
MOT
Next, rotate the scroll control to select the type of
Motorola system you want to program, then briefly
press the scroll control to select it.
•
•
•
P25 - Use for Motorola Astro APCO 25 Digital
systems in any band
800MHz Standard - Use for 800 MHz systems
that use the standard band plan
800MHz Splinter - Use for 800 MHz systems
that use the splinter band plan (typically near
international borders)
Note: Splinter systems have frequencies below
866 MHz that end in 0. For example, 851.0250
would be the frequency of a splinter system.
•
•
•
900MHz Band - Use for 900 MHz systems
VHF band - Use for VHF systems
UHF band - Use for UHF systems
Confirm? Yes=”E” / No=”.”
Note: The scanner creates an empty MOT system,
with a default name of "System n
M." "n" is a
number that increments as you add new systems,
"M" indicates that this is a MOT system.
Next, refer to the appropriate section to set
systemwide options. For most settings, you can
accept the default. However, for the items in bold, you
must enter information in order for your scanner to
scan the system.
•
•
•
•
•
•
See “Editing the System Name” on Page 70
See “Editing the System Quick Key” on Page 71
See “Setting System Lockout” on Page 71
See “Setting the System Hold Time” on Page 72
See “Setting the Channel Delay Time” on Page 72
See “Setting ID Scan/Search (Trunked Systems
Only)” on Page 73
•
•
See "Setting the Band Plan (Motorola P25 and
VHF/UHF Systems Only)" on Page 74
See “Editing the Fleet Map (Motorola Systems
Only)” on Page 75 (must be set up for Type I and
Type II Hybrid systems)
Programming Radio Systems
59
Download from Www.Somanuals.com. All Manuals Search And Download.
•
•
•
•
•
•
•
•
See“Setting the Motorola Status Bit (Motorola
Systems Only)” on Page 76
See “Setting the End Code Operation (Motorola
Systems Only)” on Page 77
See “Setting I-Call (Motorola and EDACS Systems
Only)” on Page 77
See “Setting Emergency Alert (Motorola and
EDACS Systems Only)” on Page 78
See “Adjusting the P25 Level (Motorola and
Conventional Systems Only)” on Page 79
See “Setting Control-Channel Only (Motorola
Systems Only)” on Page 78
See “Reviewing Locked Out Frequencies” on
Page 79
See “Setting System Attenuation (Trunked
Systems Only)” on Page 81
•
•
•
•
See “Deleting Systems” on Page 81
See “Copying Systems” on Page 81
See “Setting System Frequencies” on Page 64
See “Entering/Editing Motorola Channel Groups”
on Page 62
Setting System Frequencies
Program System
Select the system
Set Frequencies
New Frequencies
Input a system frequency, then press the scroll
control.
To enter additional frequencies, press
scroll control to select New Frequency, then repeat
the above.
, use the
Note: If you select Control Channel Only mode (see
“Setting Control-Channel Only (Motorola Systems
Only)” on Page 78), you only need to enter the
frequency(s) that can be assigned as the control
channel. Most frequency lists usually indicate which of
Programming Radio Systems
60
Download from Www.Somanuals.com. All Manuals Search And Download.
the frequencies are the control channel frequencies.
Otherwise, you must enter all of the frequencies.
Setting Modulation
Program System
Select the system
Set Modulation
Auto - the scanner uses the default modulation for
the frequency band.
FM - the scanner uses FM (frequency modulation) for
the frequency band.
NFM - the scanner uses narrowband FM for the
frequency band.
Note: The default setting is Auto.
This setting controls the modulation method used for
the frequency band. In most cases, if you leave this
set to Auto, the scanner automatically selects the
correct modulation type for the system you are
Programming.
Setting Attenuation
Program System
Select the system
Set Attenuator
This setting controls whether the attenuator will be on
or off for the current system. Select your setting then
press the scroll control.
Off
On
- the attenuator is off.
- system frequencies are attenuated by about
18 dB.
Notes:
•
Turn on this setting if you are near strong signal
sources. Attenuation can help reduce interference
And desensitization that strong signals create.
Programming Radio Systems
61
Download from Www.Somanuals.com. All Manuals Search And Download.
•
You can also turn this setting on or off by holding
on a trunked system, then pressing + E.
Entering/Editing Motorola Channel
Groups
To enter channels in a system, first set up a channel
group (or groups) to hold the channels. Then, enter
the channel and channel parameters in the group(s).
Setting Up a Channel Group
Program System
Select the system
Edit Group
New Group
The scanner creates a group with a default name of
Group nn. nn increments by one for each new
group you create within a system.
Next, refer to the appropriate section to set group-
wide options:
•
See “Entering/Editing the Group Name” on
Page 82
•
•
•
•
See “Setting the Group Quick Key” on Page 83
See “Deleting Groups” on Page 83
See “Copying Systems” on Page 81
See “Entering/Editing Motorola Channels” on
Page 62
•
See “Setting I-Call (Motorola and EDACS Systems
Only)” on Page 77
Entering/Editing Motorola Channels
Program System
Select the system
Edit Group
Select the group
Edit Channel
New Channel
Programming Radio Systems
62
Download from Www.Somanuals.com. All Manuals Search And Download.
Enter a talk group ID
Note: You can enter I-Calls by pressing
then the
I-Call number. You can enter the I-Call wild card by
pressing then 0.
Refer to the appropriate section to change a
channel setting:
•
See “Adjusting the P25 Level (Motorola and
Conventional Systems Only)” on Page 79
See “Editing the Channel Name” on Page 84
See “Editing the Talk Group ID (Trunked Channels
Only)” on Page 86
•
•
•
•
•
See “Setting Channel Lockout” on Page 89
See “Deleting Channels” on Page 90
See “Copying/Pasting Channels” on Page 90
To program another channel within the same group,
press , then repeat the above. To create another
channel group and enter more channels, press
three times, then proceed from “Entering/Editing
Motorola Channel Groups” on Page 62.
Programming EDACS Systems
Program System
New System
EDCS
Confirm? Yes=”E” / No=”.”
Next, rotate the scroll control to select the type of
EDACS system you want to program, then briefly
press the scroll control to select it.
•
•
•
WIDE - Use for wideband EDACS systems
NARROW - Use for narrowband EDACS systems
SCAT - Use for EDACS SCAT (Single Channel
Autonomous Trunking)
Confirm? Yes=”E” / No=”.”
The scanner creates an empty EDACS system, with a
default name of System n
E.
Programming Radio Systems
63
Download from Www.Somanuals.com. All Manuals Search And Download.
n is a number that increments as you add new
systems. E indicates that this is an EDACS system.
Next, refer to the appropriate section to set
systemwide options. For most settings, you can
accept the default. However, for the items in bold, you
must enter information in order for your scanner to
scan the system.
•
•
•
•
•
•
See “Editing the System Name” on Page 70
See “Editing the System Quick Key” on Page 71
See “Setting System Lockout” on Page 71
See “Setting the System Hold Time” on Page 72
See “Setting the Channel Delay Time” on Page 72
See “Setting ID Scan/Search (Trunked Systems
Only)” on Page 73
•
•
•
•
•
See “Setting I-Call (Motorola and EDACS Systems
Only)” on Page 77
See “Adjusting the P25 Level (Motorola and
Conventional Systems Only)” on Page 79
See “Setting the EDACS ID Format (EDACS
Systems Only)” on Page 80
See “Reviewing Locked Out Frequencies” on
Page 79
See “Setting Channel Attenuation (Conventional
Channels Only)” on Page 88
•
•
•
See “Deleting Systems” on Page 81
See “Copying Systems” on Page 81
See “Setting System Frequencies” on Page
64 (below)
•
See “Entering/Editing EDACS Channel Groups”
on Page 65
Setting System Frequencies
Program System
Select the system
Set Frequencies
New Frequency
Programming Radio Systems
64
Download from Www.Somanuals.com. All Manuals Search And Download.
Input a system frequency, then press the scroll
control. The scanner then prompts you to enter the
LCN for the entered frequency. Enter the LCN, then
press the scroll control.
To enter additional frequencies, press
, use the
scroll control to select New Frequency, then repeat
the above.
Note: The scanner only accepts a single frequency
and no LCN for SCAT systems.
Entering/Editing EDACS Channel Groups
To enter channels in a system, first set up a channel
group (or groups) to hold the channels. Then, enter
the channel and channel parameters in the group(s).
Setting Up a Channel Group
Program System
Select the system
Edit Group
New Group
The scanner creates a group with a default name of
Group nn. nn increments by one for each new
group you create within a system.
Next, refer to the appropriate section to set group-
wide options:
•
See “Entering/Editing the Group Name” on
Page 82
•
•
•
•
See “Setting the Group Quick Key” on Page 83
See “Deleting Groups” on Page 83
See “Editing the Channel Name” on Page 84
See “Setting Group Lockout” on Page 83
Entering/Editing EDACS Channels
Program System
Select the system
Edit Group
Programming Radio Systems
65
Download from Www.Somanuals.com. All Manuals Search And Download.
Select the group
Edit Channel
New Channel
Enter a talk group ID
Note: You can enter I-Calls by pressing
then the
I-Call number. You can enter the I-Call wild card by
pressing then 0.
Refer to the appropriate section to change a
channel setting:
•
•
•
See “Editing the Channel Name” on Page 84
See “Setting Channel Lockout” on Page 89
See “Editing the Talk Group ID (Trunked Channels
Only)” on Page 86
•
•
See “Deleting Channels” on Page 90
See “Copying/Pasting Channels” on Page 90
To program another channel within the same group,
press , then repeat the above. To create another
channel group and enter more channels, press
three times, then proceed from “Entering/Editing
EDACS Channel Groups” on Page 65.
Programming LTR Systems
Program System
New System
LT
Confirm? Yes=”E” / No=”.”
The scanner creates an empty LTR system, with a
default name of System n
n is a number that increments as you add new
L.
systems. L indicates that this is an LTR system.
Next, refer to the appropriate section to set
systemwide options. For most settings, you can
accept the default. However, for the items in bold, you
must enter information in order for your scanner to
scan the system.
•
See “Editing the System Name” on Page 70
Programming Radio Systems
66
Download from Www.Somanuals.com. All Manuals Search And Download.
•
•
•
•
See “Setting the System Hold Time” on Page 72
See “Editing the System Quick Key” on Page 71
See “Setting the Channel Delay Time” on Page 72
See “Setting ID Scan/Search (Trunked Systems
Only)” on Page 73
•
•
See “Reviewing Locked Out Frequencies” on
Page 79
See “Setting Channel Attenuation (Conventional
Channels Only)” on Page 88
•
•
•
See “Deleting Systems” on Page 81
See “Copying Systems” on Page 81
See “Setting System Frequencies” on Page
67 (below)
•
See “Entering/Editing LTR Channel Groups” on
Page 67 (below)
Setting System Frequencies
Program System
Select the system
Set Frequencies
New Frequency
Input a system frequency, then press the scroll
control. The scanner then prompts you to enter the
LCN for the entered frequency. Enter the LCN, then
press the scroll control.
To enter additional frequencies, press , use the
scroll control to select New Frequency, then repeat
the above.
Entering/Editing LTR Channel Groups
To enter channels in a system, first set up a channel
group (or groups) to hold the channels. Then, enter
the channel and channel parameters in the group(s).
Menu
Menu
Programming Radio Systems
67
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Up a Channel Group
Program System
Select the system
Edit Group
New Group
The scanner creates a group with a default name of
Group nn. nn increments by one for each new
group you create within a system.
Next, refer to the appropriate section to set group-
wide options:
•
See “Entering/Editing the Group Name” on
Page 82
•
•
•
•
See “Setting the Group Quick Key” on Page 83
See “Setting Group Lockout” on Page 83
See “Deleting Groups” on Page 83
See “Entering/Editing LTR Channels/ Talkgroups”
on Page 68 (below)
Entering/Editing LTR Channels/
Talkgroups
Program System
Select the system
Edit Group
Select the group
Edit Channel
New Channel
Enter a talk group ID
Refer to the appropriate section to change a
channel setting:
•
•
•
See “Editing the Channel Name” on Page 84
See “Setting Channel Lockout” on Page 89
See “Editing the Talk Group ID (Trunked Channels
Only)” on Page 86
•
•
See “Deleting Channels” on Page 90
See “Copying/Pasting Channels” on Page 90
Programming Radio Systems
68
Download from Www.Somanuals.com. All Manuals Search And Download.
To program another channel within the same group,
press , then repeat the above.
To create another channel group and enter more
channels, press four times, then proceed from
“Setting Up a Channel Group” on Page 68 .
To direct-enter LTR talkgroups, follow the steps under
“Quick-Storing Channels or Talk Group ID’s” on
Page 43.
Programming Radio Systems
69
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming/Editing Optional Settings
This section details the instructions for each of the
optional programming steps referred to in
“Programming Radio Systems” on Page 56. Use the
instructions in the appropriate section to enter or edit
a setting.
System-Level Settings
These settings apply to the entire system.
Editing the System Name
Program System
Select the system
Edit Name
To enter a letter, turn the scroll control until the
character you want appears. To enter a decimal point,
press
hold
To move the cursor to the right, press 6/> or hold
. To move the cursor to the left, press </4 or
and rotate the scroll control to the left.
and rotate the scroll control to the right.
To clear a character, press
characters, press 3 times.
twice. To clear all
To accept an entry, press E or press down on the
scroll control.
Hints:
•
Each system name can be up to 16 characters.
Abbreviate as necessary to fit.
•
The default system names include the following
letter in the 16th position to indicate the system
type:
M = Motorola
E = EDACS
L = LTR
C = Conventional
Programming/Editing Optional Settings
70
Download from Www.Somanuals.com. All Manuals Search And Download.
Editing the System Quick Key
Program System
Select the system
Edit Sys Option
Set Quick Key
After selecting this option, select any number from
0-99 to assign the system to a quick key or press to
assign the system to no quick key, then press E.
Hints:
•
Access single-digit system Quick Keys by
pressing the single digit on the keypad during
scanning. Access two-digit system Quick Keys by
pressing
then both digits.
•
•
You can assign as many systems to the same
quick key as you want.
To be scanned, a system’s quick key must be
activated and the system must be unlocked.
Setting System Lockout
Program System
Select the system
Edit Sys Option
Set Lockout
This setting controls whether the system is scanned
when its quick key is enabled. Rotate the scroll control
to select your setting, then press E.
Lockout - the system is not scanned
Unlocked - the system is scanned
Note: You can also lock or unlock a system by holding
and rotating the scroll control to select the
system, then pressing
+ L/O.
Programming/Editing Optional Settings
71
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the System Hold Time
Program System
Select the system
Edit Sys Option
Set Hold Time
This setting controls how many seconds the scanner
scans a system before moving to the next unlocked
system. Enter a value from 0-255, then press E to
save the setting.
Notes:
•
This setting is available only when a control
channel exists in a trunked system.
•
If you select 0, the scanner stays on the system
for a minimal time (only long enough to check cur-
rent system activity).
•
•
The default setting is 2 seconds for each system.
For conventional systems, all unlocked channels
will be scanned at least once regardless of this
setting.
•
•
The scanner moves to the next system after the
hold time expires, any current transmission ends,
and the channel delay time expires.
Due to the control method for these system types,
the scanner always scans LTR and EDACS SCAT
systems for at least 1 second.
Setting the Channel Delay Time
Program System
Select the system
Edit Sys Option
Set Delay Time
This setting controls how many seconds the scanner
waits after a transmission ends before resuming
Programming/Editing Optional Settings
72
Download from Www.Somanuals.com. All Manuals Search And Download.
scanning. Enter a value from 1 - 5 or Off , then
press E or the scroll control.
Notes:
•
•
The default setting is 2 seconds for each system.
This setting applies to all channels within the
system.
Setting ID Scan/Search
(Trunked Systems Only)
Program System
Select the system
Edit Sys Option
ID Scan/Search
This setting controls how the system will be scanned.
Select your setting, then press E.
ID Scan - the scanner only stops on channels you
have programmed into the system.
ID Search - the scanner stops on any transmission
for unlocked talk group ID's.
Note: You can also change this setting by pressing
Scan while scanning the system.
Programming/Editing Optional Settings
73
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the Band Plan
(Motorola P25 and VHF/UHF Systems Only)
Program System
Select the system
Edit Sys Option
Edit Band Plan
For Motorola VHF/UHF system
To properly track Motorola VHF and UHF trunked
Systems, the user must enter what is known as the
base, the spacing frequencies and offset channels for
each System.
Follow these steps:
1. Scroll to the Band Plan table entry you want to edit
and press E.
2. Enter the base frequency and press E.
3. Select the step frequency and press E.
4. Enter the channel offset and press E.
Repeat 1-4 for additional table entries.
Notes: If Band Plan 1 is set 0 for the Base Frequency,
Band Plan 2 and Band Plan 3 are also cleared. If
Band Plan 2 is set 0 for the Base Frequency, Band
Plan 3 is cleared too. You can input the following
frequency for the base frequency. VHF system :
136.0000 - 174.0000 MHz UHF system : 406.0000 -
512.0000 MHz Or, the channel offset can be input
from 380 to 759.
For Motorola P25 Systems
The UBCD396T includes two operation modes for
P25 systems: explicit mode and implicit mode channel
assignment. Explicit mode systems include all
information needed to determine voice frequencies on
the control channel. The scanner automatically sets
the band plan sent from the repeater. In implicit mode
you must supply the system’s band plan for the
scanner to correctly determine voice frequencies.
Follow these steps:
Programming/Editing Optional Settings
74
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Scroll to the Band Plan table entry you want to edit
and press E.
2. Enter the base frequency for the table entry and
press E.
3. Enter the spacing for the table entry (in kHz) and
press E.
Repeat 1-3 for additional table entries.
Notes:
· For Explicit mode systems, leave all entries blank.
· There is no way to determine the correct entries
using the scanner (other than trial and error). You
must get this information from another source. Uniden
Australia and Uniden NZ do not have this information.
Editing the Fleet Map
(Motorola Systems Only)
Program System
Select the system
Edit Sys Option
Edit Fleet Map
For Motorola Type I systems, you must enter a system
fleet map in order for the scanner to properly track
and display talk group ID's. The fleet map is usually
included in the same resource that provided system
frequencies and talk group ID lists.
Programming/Editing Optional Settings
75
Download from Www.Somanuals.com. All Manuals Search And Download.
Rotate the scroll control to select the fleet map:
Preset - select from the 16 most common fleet maps
(see “Preset Fleet Maps” on Page 123). Press E to
select.
Custom - allows you to enter a custom fleet map.
Enter the size code for each block. Press E to select.
Notes:
•
If you don't know the fleet map for your Motorola
Type I system, check the Internet. This information
is commonly posted on sites such as those we
reference in “Where To Get More Information” on
Page 26.
•
The default setting of no fleet map is the correct
setting for Motorola Type II systems.
Setting the Motorola Status Bit
(Motorola Systems Only)
Program System
Select the system
Edit Sys Option
Set Status Bit
Motorola analog systems use talk group ID's in
multiples of 16. ID numbers that fall between these
ID's indicate special status flags for the system.
This setting determines how the scanner will handle
ID's that are not multiples of 16. Select your setting
then press E.
Ignore - the scanner rounds all received ID's down
to the next interval of 16.
Yes - the scanner treats all received ID's as unique
ID's.
Note: The default setting is Ignore .
Programming/Editing Optional Settings
76
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the End Code Operation
(Motorola Systems Only)
Program System
Select the system
Edit Sys Option
Set End Code
This setting determines how the scanner handles the
transmission end code sent by most Motorola
systems. Select your setting then press E.
Yes - the scanner immediately returns to the control
channel when it detects the end code.
Ignore - the scanner does not return to the control
channel until the carrier drops.
Note: The default setting is Yes .
Setting I-Call
(Motorola and EDACS Systems Only)
Program System
Select the system
Edit Sys Option
Set I-Call
This setting determines how your scanner treats I-
calls while ID Searching.
On - the scanner tracks I-calls. Press E to select.
Off - the scanner ignores I-calls. Press E to select.
Only - the scanner only tracks I-calls and ignores
other radio traffic on the system. Press E to select.
Note: The default setting is Off .
Programming/Editing Optional Settings
77
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Emergency Alert
(Motorola and EDACS Systems Only)
Program System
Select the system
Edit Sys Option
Emergency Alert
Off - the scanner does not alert you to emergency
transmissions.
Alert 1 - 9 - the scanner sounds an alert beep to
notify you of the emergency transmission. You can
choose any of 9 different beep types.
Set Level
Auto - the scanner automatically sets the emergency
alert beep to the master volume level.
Level 1 - 15 - the scanner adjusts the volume you
hear to the level you select.
Setting Control-Channel Only
(Motorola Systems Only)
Program System
Select the system
Edit Sys Option
Set C-Ch Only
This setting determines the frequencies you need to
enter for Motorola systems. Select your setting, then
press E.
Off - you must enter all voice and control channel
frequencies.
On - you only need to enter control channel
frequencies.
Note: The scanner defaults to On .
Programming/Editing Optional Settings
78
Download from Www.Somanuals.com. All Manuals Search And Download.
Reviewing Locked Out Frequencies
Program System
Select the system
Edit Sys Option
Rvw ID: Srch L/O
The scanner displays the first locked-out frequency
and prompts you to unlock the frequency. Press E to
unlock the frequency. Or, rotate the scroll control or
press to select a different frequency. To exit the
review, press .
Clearing All Locked-Out IDs
Program System
Select the system
Edit Sys Option
Clr All L/O IDs
The scanner prompts you to confirm deletion. To
confirm and delete all locked-out IDs in the selected
system, press E. Otherwise, to cancel, press
.
Adjusting the P25 Level
(Motorola and Conventional Systems
Only)
Program System
Select the system
Edit Sys Option
Adjust P25 Level
This setting determines some system-specific
parameters for digital channels. In most cases, setting
this to Auto provides the best performance.
However, you can also manually set the digital decode
threshold. This setting affects all channels in the
current system.
Programming/Editing Optional Settings
79
Download from Www.Somanuals.com. All Manuals Search And Download.
Auto - the scanner automatically adjusts the digital
decode threshold to match the transmission you are
hearing when it receives a strong signal and has a
high decode rate.
Manual - lets you manually adjust the digital decode
threshold. To manually adjust the P25 level, select
Manual .
Default - sets the digital decode threshold to the
default value. Use this setting to return to the value
that usually provides adequate performance. This is
handy is you have manually adjusted the value to a
setting that prevents proper decoding.
Note: This setting has no effect on how these
systems are received.
Setting the EDACS ID Format
(EDACS Systems Only)
Program System
Select the system
Edit Sys Option
EDCS ID Format
EDACS talk group ID's are commonly provided in one
of two formats: AFS and Decimal. This setting
determines how you enter EDACS ID's and how the
scanner displays them.
AFS Format - the scanner uses AFS format for talk
group ID's
Decimal Format - the scanner uses decimal format
for talkgroup ID's
Notes:
•
The scanner defaults to AFS (agency, fleet,
subfleet) format - the format used in most EDACS
systems.
•
See “EDACS Trunking” on Page 24 for more
information about the AFS format.
Programming/Editing Optional Settings
80
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting System Attenuation
(Trunked Systems Only)
Program System
Select the system
Set Attenuator
This setting controls whether the attenuator will be on
or off for the current system. Select your setting then
press E.
Off - the attenuator is off.
On - system frequencies are attenuated by about 18
dB.
Notes:
•
Turn on this setting if you are near strong signal
sources. Attenuation can help reduce interference
and desensitization that strong signals create.
•
You can also turn this setting on or off by holding
on a trunked system, then pressing
+ E.
Deleting Systems
Program System
Select the system
Delete System
The scanner prompts you to confirm deletion.
To confirm, press E. To cancel, press
.
Notes:
•
Deleted systems cannot be restored. You must
re-enter them.
You cannot restore preloaded systems.
•
Copying Systems
To copy a system including all settings, groups, and
channels:
Programming/Editing Optional Settings
81
Download from Www.Somanuals.com. All Manuals Search And Download.
Program System
Select the system
Copy System
New Sys Name?
Enter a name for the copied system, then press E.
Group-Level Settings
The settings in this section apply to all of the channels
stored in the current group.
Entering/Editing the Group Name
Program System
Select the system
Edit Group
Select the group
Edit Name
Follow these steps to enter/edit the group name.
1. Rotate the scroll control to select the first letter.
2. Press and hold down then rotate the scroll
control once to select the next letter.
3. Repeat Steps 1 and 2 until you have entered the
system name. Then press E or press down on the
scroll control to accept the setting.
Hints:
•
Each group name can be up to 16 characters.
Abbreviate as necessary to fit.
•
The group and system name alternate in the top
line of the display when the scanner stops on a
channel.
•
•
Press
Press
twice to delete the current character.
three times to clear the entire alpha tag.
Programming/Editing Optional Settings
82
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the Group Quick Key
Program System
Select the system
Edit Group
Select the group
Set Quick Key
After selecting this option, press 0-9 to assign the
group to a quick key or press to assign the system
to no quick key, then press E.
Hints:
•
You can assign as many groups to the same quick
key as you want.
•
A group’s quick key must be activated to be
scanned.
Setting Group Lockout
Program System
Select the system
Edit Group
Select the group
Set Lockout
This setting determines whether the scanner will scan
this group when it is enabled. Select your setting, then
press E.
Lockout - the group is not scanned.
Unlocked - the group is scanned.
Note: The default setting is Unlocked .
Deleting Groups
Program System
Select the system
Edit Group
Programming/Editing Optional Settings
83
Download from Www.Somanuals.com. All Manuals Search And Download.
Select the group
Delete Group
The scanner prompts you to confirm deletion. To con-
firm, press E. To cancel, press
.
Note: Deleted groups cannot be restored. You must
re-enter them.
Channel-Level Settings
These settings affect only the channel you are
programming.
Editing the Channel Name
Program System
Select the system
Edit Group
Select the group
Edit Channel
Select the channel
Edit Name
Follow these steps to enter/edit the channel name.
1. Rotate the scroll control to select the first letter.
2. Press and hold down then rotate the scroll
control once to select the next letter.
3. Repeat Steps 1 and 2 until you have entered the
channel name. Then press E or press down on the
scroll control to accept the setting.
Hints:
•
•
•
Each channel name can be up to 16 characters.
Abbreviate as necessary to fit.
The channel name appears on the second line of
the display when the scanner stops on a channel.
If you do not enter a channel name, the scanner
displays the frequency (for conventional systems)
Programming/Editing Optional Settings
84
Download from Www.Somanuals.com. All Manuals Search And Download.
or the talk group ID (for trunked systems) when it
stops on a channel.
•
•
•
Press
Press
twice to delete the current character.
three times to clear the entire alpha tag.
Channel names take up extra memory. To
maximize channels, use channel names only
where necessary.
Editing Frequencies
(Conventional Channels Only)
Program System
Select the system
Edit Group
Select the group
Edit Channel
Select the channel
Input Frequency
Input the frequency, then press the scroll control.
To change the frequency you entered, turn the scroll
control to select Edit Frequency , then press the
scroll control.
Setting Channel Priority
(Conventional Channels Only)
Program System
Select the system
Edit Group
Select the group
Edit Channel
Select the channel
Set Priority
This setting controls whether the scanner treats the
channel as a priority channel while scanning. Select
your setting, then press E.
Programming/Editing Optional Settings
85
Download from Www.Somanuals.com. All Manuals Search And Download.
On - when you turn on the Priority feature, the channel
will be scanned every 2 seconds. appears.
Off - the channel will not be treated with priority.
Note: The default setting is Off .
Setting Channel Alert
Program System
Select the system
Edit Group
Select the group
Edit Channel
Select the channel
Set Alert
Off - the scanner does not alert you to emergency
transmissions.
Alert 1 - 9 - the scanner sounds an alert beep to
notify you of the emergency transmission. You can
choose any of 9 different beep types.
Set Level
Auto - the scanner automatically sets the emergency
alert beep to the master volume level.
Level 1 - 15 - the scanner adjusts the volume you
hear to the level you select.
Editing the Talk Group ID (Trunked
Channels Only)
Program System
Select the system
Edit Group
Select the group
Edit Channel
Programming/Editing Optional Settings
86
Download from Www.Somanuals.com. All Manuals Search And Download.
Select the talk group ID
Edit TGID
To edit the talk group ID, enter the talk group ID you
want using the number keys on the keypad. Then
press down on the scroll control to accept it.
Setting CTCSS/DCS
(Conventional Channels Only)
Program System
Select the system
Edit Group
Select the group
Edit Channel
Select the channel
Set CTCSS/DCS
This setting controls how a subaudible CTCSS or
DCS is used for the channel. Select your setting, then
press E.
Off - any signal opens squelch.
Search - the scanner searches for and displays any
CTCSS or DCS tone that accompanies the
transmission.
CTCSS - the scanner only opens squelch if the CTCSS
tone you select is also present with the signal. The
scanner then prompts you to enter or scroll to the
desired tone.
DCS - the scanner only opens squelch if the DCS tone
you select is also present with the signal. The scanner
then prompts you to enter or scroll to the desired tone.
Set Lockout - the scanner does not stop on the
channel if the tone you select is present. The scanner
prompts you to select a CTCSS or DCS tone.
Notes:
•
The scanner will not detect or decode P25 signals
if you turn on CTCSS/DCS search.
Programming/Editing Optional Settings
87
Download from Www.Somanuals.com. All Manuals Search And Download.
•
•
The default setting is Off .
See “What is CTCSS/DCS?” on Page 17 for a
complete list of CTCSS and DCS tones.
Setting the System Frequency
Modulation
Srch/CloCall Opt
Set Modulation
Auto - the scanner uses the default modulation for
the frequency band.
AM - the scanner uses AM (amplitude modulation) for
the frequency band.
FM - the scanner uses FM (frequency modulation) for
the frequency band.
NFM - the scanner uses narrowband FM for the
frequency band.
WFM - the scanner uses wideband FM for the
frequency band.
Note: The default setting is Auto .
This setting controls the modulation method used for
the frequency band. In most cases, if you leave this
set to Auto , the scanner automatically selects the
correct modulation type for the system you are
programming.
Setting Channel Attenuation
(Conventional Channels Only)
Program System
Select the system
Edit Group
Select the group
Edit Channel
Programming/Editing Optional Settings
88
Download from Www.Somanuals.com. All Manuals Search And Download.
Select the channel
Set Attenuator
This setting controls whether the scanner attenuates
signals on this channel. Select your setting, then press E.
On - the channel is attenuated by about 18 dB.
Off - the channel is not attenuated.
Notes:
•
•
The default setting is Off .
For trunked systems, the attenuation is a system-level
setting.
You can also toggle this setting by holding on the
•
channel and pressing
and E.
Setting Channel Lockout
Program System
Select the system
E
E
Edit Group
E
Select the group
E
Edit Channel
Select the channel
Set Lockout
This setting determines whether the scanner will scan
this channel when its system and group are enabled.
Select your setting, then press E.
Lockout - the channel is not scanned.
Unlocked - the channel is scanned.
Notes:
•
•
The default setting is Unlocked .
You can also lock or unlock a channel by selecting
it while scanning or holding, then pressing L/O.
See “Basic Operation” on Page 38.
Programming/Editing Optional Settings
89
Download from Www.Somanuals.com. All Manuals Search And Download.
Deleting Channels
Program System
Select the system
Edit Group
Select the group
Edit Channel
Select the channel
Delete Channel
The scanner prompts you to confirm deletion.
To confirm, press E. To cancel, press
.
Note: Deleted channels cannot be restored. You must
re-enter them.
Copying/Pasting Channels
To copy a channel including all settings:
Program System
Select the system
Edit Group
Select the group
Edit Channel
Select the channel
Copy Channel
The scanner copies the channel into a copy buffer.
To paste the channel into the same or another system:
Program System
Select the system
Edit Group
Select the group
Edit Channel
Select the channel
Paste Channel
Then, if necessary, edit the channel you copied to give
it a unique name and other settings.
Note: The paste option appears only if you have previously copied
a channel from a system of the same type you are currently editing.
Programming/Editing Optional Settings
90
Download from Www.Somanuals.com. All Manuals Search And Download.
Searching And Storing
Service Search
Service Search lets you quickly select and search the
scanner’s preprogrammed search ranges. During
service search, the scanner searches starting with the
lowest frequency in the search range you select to the
highest frequency in the range.
Search for ...
Service Search
Select the service search type
The following search bands appear.
•
•
•
•
•
•
•
•
•
Air
CB Radio
UHF CB Radio
Racing
TV Broadcast
FM Broadcast
Police
Marine
Railroad
The scanner searches the service you selected,
stopping on any transmission it finds and displaying
the frequency. Turn the scroll control to change the
search direction. An arrow appears, showing the
current search direction.
To hold searching, press Hold. To resume searching,
press then press Scan/Srch. Or, press Hold .
To lock out a frequency found while searching, press
L/O. Locked Out resumes service search.
Notes:
Searching and Storing
91
Download from Www.Somanuals.com. All Manuals Search And Download.
•
•
If all frequencies in the search band you selected
are locked out, All Locked! appears and the
scanner does not search the band.
If the service you select uses channels (such as
TV Broadcast or Marine), the scanner displays the
service channel number.
Quick Search
Quick Search lets you search from the currently-tuned
frequency if you are scanning a conventional system
or sets the system to ID search if you are scanning a
trunked system.
If you are on a conventional system or channel, press
and Scan/Srch to start quick search. Quick
Search? Yes = ”E” / No = ”.” appears.
Qck Search Hold appears if you press Hold.
Press E to start quick search or No to go to the search
menu.
CTCSS/DCS Search
CTCSS/DCS Search lets you search for CTCSS or
DCS tones when it finds an active frequency in search
and Close Call modes. You can identify up to 50
CTCSS tones and 104 DCS codes.
Note: The scanner will not detect or decode P25
signals if you turn on CTCSS/DCS search.
Srch/CloCall Opt
CTCSS/DCS Search
Turning this option on lets the scanner search for
CTCSS/DCS tones. If the scanner detects the tone, it
displays the tone’s frequency and DCS code. Select
your setting, then press the scroll control.
On
- CTCSS/DCS search is turned on.
Off - CTCSS/DCS search is turned off.
Searching and Storing
92
Download from Www.Somanuals.com. All Manuals Search And Download.
Custom Search
Custom Search lets you program and search 10
custom search ranges. You can search any of these
ranges simultaneously and select each custom search
range you set. During custom search, the scanner
searches starting with the lowest frequency in the
search range you select to the highest frequency in
the range.
Notes:
•
•
Search ranges are preset. See “Editing a Custom
Search Range” on Page 94 to change the range.
You cannot turn off all custom search ranges.
Search for ...
OR
+ Scan/Srch
Custom Search
The scanner starts custom search of the custom
search range you selected, stopping on any
transmission it finds and displaying the frequency.
Turn the scroll control to change the search
direction. An arrow appears, showing the current
search direction.
To turn search ranges on or off, press 0 and 1-9.
To hold searching, press Hold. To resume searching,
press
then press Scan/Srch or Hold again.
To lock out a frequency found while searching, press
L/O. Locked Out appears and the scanner
resumes custom search.
If you turn off the active custom search range, the
scanner skips to the next custom search range and
continues searching.
Note: If all frequencies in all active custom search
ranges are locked out, All Locked! appears and
the scanner does not stop.
Searching and Storing
93
Download from Www.Somanuals.com. All Manuals Search And Download.
Editing a Custom Search Range
You can edit up to 10 custom search ranges. The
names of the custom search ranges appear on the
display. The default custom search range names
appear as Custom 1 , Custom 2 , and so on.
Search for ...
OR
+ Scan/Srch
Edit Custom
Select your setting, then press the scroll control.
Edit Name - lets you edit the custom search range’s
name.
Edit Srch Limit - lets you view and select the
frequency ranges to search. The scanner prompts you
to enter the upper and lower search limits.
Set Delay Time - lets you set the amount of time
the scanner will delay before continuing to search
after a transmission ends.
Set Modulation - lets you set the custom search
range’s modulation type.
Set Attenuator - lets you set whether the scanner
will attenuate reception by 18dB during search.
Set Data Skip - lets you set whether the scanner
will skip data transmissions during search.
Set Step - lets you set the custom search range’s
step (the gap between frequencies).
Set C-Ch Only - lets you search for a Motorola
control channel. If it finds one, the scanner scans the
system.
Adjust P25 Level - adjusts the digital decode
threshold to match the transmission you are
hearing when it receives a strong signal and has a
high decode rate.
Search with Scan - sets whether the scanner
includes the custom search during scanning.
Searching and Storing
94
Download from Www.Somanuals.com. All Manuals Search And Download.
If unlocked, the scanner first scans all selected
systems, then searches the selected service searches
for the selected hold time (0-255 seconds).
Editing a Service Search
You can change the way service search works for
each service.
Search for ...
OR
+ Scan/Srch
Edit Service
Select your setting, then press the scroll control.
• Set Delay Time This setting determines how
long the scanner waits after a transmission ends
before resuming quick search or Close Call
operation. Select your setting, then press the scroll
control.
Off The scanner resumes immediately when
the transmission ends.
1 - 5 sec The scanner waits the set amount
of time after the transmission ends before
resuming.
Note: The default setting is 2 sec .
• Set Attenuator This setting controls the
attenuator for search operation. Select your
setting, then press the scroll control.
Off The attenuator is off.
On Reception is attenuated by about 18 dB.
Note: Turn on this setting if you are near other
strong signal sources. Attenuation sometimes helps
to reduce interference and desensitization that
strong signals create.
• Search with Scan This setting controls how
search with scan works.
Searching and Storing
95
Download from Www.Somanuals.com. All Manuals Search And Download.
•
Set Lockout This setting controls whether
the system is scanned when its quick key is
enabled. Rotate the scroll control to select your
setting, then press the scroll control.
Locked - the system is not scanned
Unlocked - the system is scanned
Note: You can also lock or unlock a system by
pressing
pressing
, selecting the system, then
+ L/O.
•
Set Hold Time This setting controls how
many seconds the scanner scans a system
before moving to the next unlocked system.
Enter a value from 0-255, then press the scroll
control to save the setting.
Notes:
•
If you select 0, the scanner stays on the
system for a minimal time (only long enough
to check current system activity).
•
•
The default setting is 2 seconds for each
system.
For conventional systems, all unlocked
channels will be scanned at least once
regardless of this setting.
•
The scanner moves to the next system after
the hold time expires, any current
transmission ends, and the channel delay
time expires.
Auto Search and Store
Your scanner’s Auto Store feature lets you search for
new frequencies in custom search ranges or within a
service search range on a conventional system, or
new talk group ID’s on a trunked system.
Searching and Storing
96
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting a System
To store frequencies or talk group ID’s you find during
Auto Store, you must first select a system where the
frequencies or talk group ID’s will be stored.
Search for ...
OR
+ Scan/Srch
Search and Store
Select the system where you want to store the
frequencies or talk group IDs
If no systems are programmed, No System Stored
appears. If you have already stored too many
systems, Over Limit appears.
Storing a Conventional System
You can store frequencies into the system you
selected in “Selecting a System”. Otherwise, the
scanner stores frequencies in a new group it creates.
1. Follow the steps under “Selecting a System” on
Page 97 (above). A search option appears.
2. Turn the scroll control until the type of search you
want appears, then press the scroll control to
select it. A search band appears.
If all systems are locked out, All Locked! appears
and the scanner does not store any
frequencies.
When you select a search range, the scanner looks
for active frequencies within that range and SEARCH
AND STORE appears on the display’s lower line and
the system name and search range name appear on
the display’s upper line. When the scanner finds an
active transmission, it checks to see if the frequency
has already been stored in the system. If the
frequency has already been stored, the scanner
continues to search. If the frequency has not been
stored, it stores the frequency into a group named
Searching and Storing
97
Download from Www.Somanuals.com. All Manuals Search And Download.
Storing a Trunked System
You can store talk group ID’s into the system you
selected in “Selecting a System”. Otherwise, the
scanner stores talk group ID’s in a new group it
creates.
Note: Trunked system search and store does not
work if an EDACS SCAT system is selected, a system
with no frequency is selected, the selected system is
locked out or the quick key to which the system
belongs is turned off, and the group you selected to
store found talk group ID’s contains more talk group
ID’s than the maximum set in Max Auto Store.
To store a trunked system, follow the steps under
“Selecting a System” on Page 97. The scanner
enters ID Search and Store mode.
If the selected system is locked out, System Locked
appears and the scanner does not store any
frequencies.
When you select a search range, the scanner looks
for active talk group ID’s within that range and ID
SEARCH AND STORE appears on the display’s lower
line and the system name and search range name
appear on the display’s upper line. When the scanner
finds an active talk group ID, it checks if the talk group
ID has already been stored in the system. If it has, the
scanner continues to search. If the talk group ID has
not been stored, it stores the talk group ID into a
group named Found Channels , then resumes
searching.
The scanner creates this group if it does not already
exist.
Searching and Storing
98
Download from Www.Somanuals.com. All Manuals Search And Download.
Optimizing P25 Performance
You can optimize the scanner’s performance with
digital APCO 25 systems. Follow these steps for each
system where you can hear APCO 25 traffic.
Notes:
•
These steps work only when you can clearly
receive the system. If you are in a weak-signal
area or receive interference, these steps will not
work. These steps do not compensate for weak
signals or signals subject to interference.
•
If you set an incorrect decode threshold level in
Step 5, the scanner might stop decoding all digital
signals in the system. If this happens, change the
setting to a value between 8 and 12 then repeat
these steps.
1. Make sure the system's P25 Level option is set to
Auto (see “Adjusting the P25 Level (Motorola and
Conventional Systems Only)” on Page 79).
2. Hold on an active digital channel on the system.
3. While holding down
, briefly press the scroll
control twice. The next to last line on the display
now shows the digital error rate and the AUTO
decode threshold start level (0-20). The last line
on the display shows the decode threshold levels
for the system.
4. Allow the scanner to monitor channel activity for
several minutes. The error rate should drop for
each transmission and the threshold levels should
automatically adjust to a more optimal setting.
Then, once the threshold level settles to a stable
setting, make a note of the values. This is the
system's optimum decode threshold.
5. While holding down
, rotate the scroll control
to set the AUTO decode threshold start level to a
setting that most closely matches the system's
optimum decode threshold. Now, when the scanner
stops on a system, it will use this threshold as the
starting point for automatic optimization.
6. While holding down
control to exit this mode.
, briefly press the scroll
Optimizing P25 Performance
99
Download from Www.Somanuals.com. All Manuals Search And Download.
Using The Close Call Feature
Your scanner's Close Call ™ feature lets you set the
scanner so it detects, displays the frequency of, and
lets you hear a nearby strong radio transmission. You
can set the scanner so the Close Call feature works
"in the background" while you are scanning other
frequencies, turn off normal scanning while the Close
Call feature is working, or turn off the Close Call
feature and use the scanner normally. You can set the
scanner so it alerts you when the Close Call feature
finds a frequency. You can also set the frequency
band where you want the scanner to look for
transmissions.
To turn Close Call detection on or off, press then
. When the feature is on, appears on the display
and normal operation is briefly interrupted about every
2 seconds.
Notes:
•
The Close Call feature works well for locating the
source of strong local transmissions such as
mobile and handheld two-way radios in areas with
no other strong transmission sources. Several
factors affect Close Call performance, however.
Performance is increased with higher transmit
power, receive antenna tuned to the target band,
and a low background RF level. Other than the
antenna, you have no control over these factors,
but they explain why performance might vary by
both location and time.
•
•
The Close Call feature cannot detect satellite
dishes or any transmitter with a frequency above
or below the frequency ranges listed under the
Set CC Bands : option on Page 103.
The Close Call feature works better with some
types of transmissions than others. It might not
correctly display frequency information for trans-
mitters using a highly directional antenna (such as
an amateur radio beam antenna) or if there are
many transmitters operating at the same time in
the same area.
Using the Close Call Feature
100
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Close Call Options
Close Call
Select your setting, then press the scroll control.
Then turn the scroll control to select an option.
•
Close Call Only : Lets you set the scanner
only for Close Call searching. The scanner
does not scan frequencies or channels when
this option is turned on. To select this option,
press E.
•
CC Auto Store : Lets you select whether the
scanner automatically stores Close Call hits
into channels. If you turn this option on, the
scanner starts Close Call mode and stores any
Close Call hits, up to the maximum you
specified in the Max Auto Store setting. If the
scanner stores more hits than this setting, it
stops Autostore operation.
Turn the scroll control to display an option, then
press the scroll control.
•
Set CC Mode : Lets you select the Close Call
mode. If you turn this option on, the scanner
sets itself to its Close Call settings about once
every 2 seconds.
Turn the scroll control to display an option, then
press the scroll control.
You can also toggle this setting by pressing
then
•
Set CC Override : Lets you select how the
Close Call feature works with other scanning
activities. If you turn this option off, when the
scanner detects a Close Call signal, CC Found!
and ” E” to Listen appear for the
time you set in Set CC Pause . Press the
scroll control or E when this appears to jump to
and hold on the frequency.
If this option is turned on, the scanner overrides
the current channel and goes to the Close Call
Using the Close Call Feature
101
Download from Www.Somanuals.com. All Manuals Search And Download.
hit. The scanner displays CC Found! Press Any
Key. When you press a key, the frequency appears.
Turn the scroll control to display an option, then
press the scroll control.
•
Set CC Alert : Lets you select how the
scanner alerts you when it receives a Close
Call signal. You can select any of the following
options.
Select Mode
•
•
•
Beep (the scanner beeps when it receives a
Close Call signal)
Light (the backlight turns on when it
receives a Close Call signal)
Beep+Light (the scanner beeps and the
backlight turns on when it receives a Close
Call signal)
•
None (the scanner does not alert)
Select Beep
•
•
Off (the scanner does not beep)
Alert 1-9 - (the scanner sounds an alert
beep to notify you of a Close Call hit. When
you select an alert level, the scanner
automatically enters the setting of the Alert
volume level. You can choose different beep
types.)
Set CC Pause : Lets you select how long the
scanner waits after a hit before it returns to the
previous operation.
•
•
3/5/10/15/30/45/60 sec .
Infinite .
Turn the scroll control to display an option, then
press the scroll control to select it.
Using the Close Call Feature
102
Download from Www.Somanuals.com. All Manuals Search And Download.
•
Set CC Bands : Lets you select the Close Call
band settings. You can turn the following bands
on or off.
VHF Low 1 (25.0000-53.9900 MHz)
VHF Low 2 (54.0000-107.9000 MHz)
Air Band (108.0000 - 136.9875 MHz)
VHF High1 (137.0000-224.9000 MHz)
VHF High2 (225.0000-319.9500 MHz)
UHF
(320.0000 - 512.0000 MHz)
(764.0000 - 775.9875 MHz,
794.0000 - 956.0000 MHz,
1240.000 - 1300.0000 MHz)
800MHz +
Use the scroll control to select a band, press
the scroll control, then use the scroll control to
select On or Off and press the scroll control.
Turning off undesired bands speeds up Close
Call operation (works for all frequencies listed
above).
Close Call Hits
When the scanner detects a Close Call hit, it alerts
you according to the Override and Alert settings in the
previous section. While listening to a Close Call hit,
you can press Hold to hold on the hit frequency, press
the scroll control to quickly save the frequency into
memory, press L/O to lock out the frequency from
Close Call and Search operation, or wait for the
transmission to end. If you are in Close Call Only or
Close Call Override mode, and you do not press any
key, the scanner returns to its previous operation after
the transmission ends and the set delay time expires.
If you are holding on the frequency, press Hold again
to resume the previous operation.
Using the Close Call Feature
103
Download from Www.Somanuals.com. All Manuals Search And Download.
Search And Close Call Options
The settings in this section affect custom searches,
service searches, and Close Call operation.
Managing Locked-Out Frequencies
While searching or during Close Call operation, if you
press L/O while the scanner is stopped on a
frequency, that frequency is locked out of these
modes. You can lock out up to 200 frequencies.
Note: Locking out a frequency does not lock out a
channel that contains that frequency.
Unlocking All Frequencies
Srch/CloCall Opt
Freq Lockouts
Unlock All
The scanner prompts you to confirm deletion.
To confirm and delete all locked-out frequencies,
press the scroll control. Otherwise, to cancel, press
.
Reviewing Locked Out Frequencies
Srch/CloCall Opt
Freq Lockouts
Rvw Search L/O
The scanner displays the first locked-out frequency
and prompts you to unlock the frequency. Press the
scroll control to unlock the frequency. Or, rotate the
scroll control or press to select a different
frequency. To exit the review, press .
Searching for Subaudible Tones
Srch/CloCall Opt
CTCSS/DCS Search
This setting controls whether the scanner will search
for a subaudible tone when it stops on a transmission
during search or Close Call operation.
Search and Close Call Options
104
Download from Www.Somanuals.com. All Manuals Search And Download.
Off The scanner does not search for subaudible
tones.
On The scanner searches for and displays any
subaudible tone found.
Note: This feature does not operate when the scanner
is in AM/WFM modulation mode.
Screening Out Broadcast Sources
Srch/CloCall Opt
Broadcast Screen
This setting determines whether the scanner
automatically ignores transmissions found during
Custom Search, Service Search, or Close Call
operation that are on common broadcasts, paging
systems, and other annoyance radio sources.
Note: Broadcast screen is not effective during some
service searches.
Set All Band On - turns on broadcast screen on
each band.
Set All Band Off - turns off broadcast screen on
each band.
Set Each Band - lets you set broadcast screen only
on specific bands you select. On or Off appears next
to each option. Turn the scroll control to select an
option then press the scroll control to change the
setting.
•
Pager - the scanner skips known paging
system frequencies.
•
•
FM - the scanner skips known FM frequencies.
UHF TV - the scanner skips known UHF TV
frequencies.
•
VHF TV - the scanner skips known VHF TV
frequencies.
Search and Close Call Options
105
Download from Www.Somanuals.com. All Manuals Search And Download.
•
Band 1-10 - select the custom band where you
want to screen out broadcast sources.
Program Band - lets you program a custom
frequency range for broadcast screen. Turn the scroll
control to select an option then press the scroll control
to change the setting.
•
Band 1-10 - select the group where you want to
screen out broadcast sources.
Set Lower Limit - turn the scroll control to
enter the lower limit of the frequency range,
then press the scroll control to set it.
Set Upper Limit - turn the scroll control to
enter the upper limit of the frequency range,
then press the scroll control to set it.
Finding Repeater Output
Frequencies
Srch/CloCall Opt
Repeater Find
This feature sets whether the scanner tries to tune to
a repeater output frequency during Custom Search,
Quick Search, or Close Call operation when it detects
a transmission on a repeater input frequency. Since
you can normally only hear one side of a conversation
when you listen to an input frequency transmission,
turning this feature on can let you hear both sides of
the conversation.
On The scanner automatically applies repeater
reverse to detected transmissions. If the scanner
detects the transmission on the output frequency, it
beeps, Repeater Found appears, and it remains
on the output frequency until transmissions end. If it
does not detect a transmission on the output
frequency, it remains on the original frequency.
Search and Close Call Options
106
Download from Www.Somanuals.com. All Manuals Search And Download.
Off The scanner does not try to find the output
frequency.
Setting the Maximum Auto Store
Value
Srch/CloCall Opt
Max Auto Store
This value sets how many hits the scanner will
automatically store when it is in either Search and
Store or Close Call Auto Store mode.
Use the number keys to enter a value from 1 - 256,
then press the scroll control.
When the scanner reaches the maximum number of
hits you set, it stops the auto-store operation.
Setting the Modulation Type
Srch/CloCall Opt
Set Modulation
This setting controls the modulation type used for
quick search and Close Call operations. Select your
setting, then press the scroll control.
Auto Uses the default setting for the current
frequency (see the table at the front of the manual)
AM Uses AM (amplitude modulation)
FM Uses FM (frequency modulation)
NFM Uses narrowband FM
WFM Uses wideband FM
Setting Attenuation
Srch/CloCall Opt
Set Attenuator
Search and Close Call Options
107
Download from Www.Somanuals.com. All Manuals Search And Download.
This setting controls the attenuator for quick search
and Close Call operation. Select your setting, then
press the scroll control.
Off The attenuator is off.
On Reception is attenuated by about 18 dB.
Note: Turn on this setting if you are near other strong
signal sources. Attenuation sometimes helps to
reduce interference and desensitization that strong
signals create.
Setting Data Skip
Srch/CloCall Opt
Set Data Skip
This setting controls how the scanner behaves when it
stops on a channel that has a data signal.
On - the scanner stops briefly on the channel, but then
immediately resumes scanning automatically. Press E
to select.
Off - the scanner remains on the channel until the
transmission stops. Press the scroll control to select.
Notes:
•
If you are trying to test the Close Call feature with
a nearby transmitter and you do not talk into the
transmitter, the scanner will detect this as data and
will skip the frequency when Data Skip is on. Turn
the feature off or talk into the transmitter.
•
•
This setting is ignored for AM channels.
The default setting for this feature is Off .
Search and Close Call Options
108
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the Delay Time
Srch/CloCall Opt
Set Delay Time
This setting determines how long the scanner waits
after a transmission ends before resuming quick
search or Close Call operation. Select your setting,
then press the scroll control.
Off The scanner resumes immediately when the
transmission ends.
1 - 5 sec The scanner waits the set amount of time
after the transmission ends before resuming.
Note: The default setting is 2 sec .
Setting the Search Frequency Step
Srch/CloCall Opt
Set Step
This setting selects the frequency step used for
setting the channels. Select your setting, then press
the scroll control.
Auto The step is based on the band (see the table at
the front of the manual)
5.0 kHz , 6.25kHz , 7.5 kHz , 8.33kHz ,
10.0 kHz , 12.5 kHz , 15.0 kHz , 20.0
kHz , 25.0 kHz , 50.0 kHz , 100.0 kHz
The scanner uses the selected step.
Note: The scanner defaults to Auto .
APCO 25 Threshold Level Setting
Srch/CloCall Opt
Adjust P25 Level
This setting selects the APCO 25 threshold level
between Auto, Manual and Default. Select your
setting, then press the scroll control.
Search and Close Call Options
109
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Tone-out
Fire Tone-Out Introduction
Your scanner can be set to respond to fire tone-outs
that use standard two-tone sequential paging, short
one-tone paging, and long group tone paging. You can
save up to 10 settings. When you select a setting in
standby mode, the scanner also monitors for any
other setting that uses the same transmit frequency,
modulation, and attenuation settings.
You need tone-out setup information from the agency
you wish to monitor. Check with your local agency or
on-line resources.
Note: The Fire Tone-Out feature is not used in
Australia or New Zealand.
Setting Tone-Out Standby
Tone-Out for...
Tone-Out Standby
Turn the scroll control to select the tone-out to
monitor. All tone-outs that have the same frequency,
modulation, and attenuation setting as the one you
select, are also monitored.
In standby mode, the display cycles through all
monitored tone-out settings. Regardless of the current
display, the scanner always alerts on any received
tone-out that matches a stored setting.
If you press HOLD while in standby mode, the
scanner temporarily exits the mode and you hear all
transmissions on that frequency. No alerts sound,
even if a tone-out matches one you have stored.
Press HOLD again to return to standby mode.
Setting Up Tone-Out
Tone-Out for ...
Tone-Out Setup
Scroll to select the tone-out (1 - 10) you want to
program, then press EYES. Then you can scroll to
any of the following settings and press EYES to select
and modify the selected settings:
Using Tone-Out
110
Download from Www.Somanuals.com. All Manuals Search And Download.
•
•
Edit Name - Sets the name for the selected tone-
out setting.
Set Frequency — Sets the tone-outs RF
frequency parameters.
Edit Frequency — Enter the desired
frequency that the scanner should monitor for
the tone-out.
Set Modulation — Set the modulation type
for the paging signal.
Auto —The scanner uses the default
modulation for the frequency band. If the
default modulation is AM or WFM, the
modulation operates as FM.
FM — The scanner uses FM for the frequency
band. This is the default setting.
NFM — The scanner uses NFM modulation.
Set Attenuaton — Turn the scroll control to
select On or Off .
•
Set Tone — Sets the audio tone frequency for
the page.
Edit Tone A — Set the audio frequency
for Tone A
Edit Tone B — Set the audio frequency
for Tone B
Notes:
•
For two-tone pages, enter a value for A and B.
•
For one-tone pages using short tones of less
than 3.75 seconds, enter the tone value for A,
and 0 (zero) for B.
•
For long-tone pages, such as group pages of
more than 3.75 seconds, enter 0 (zero) for A
and the tone value for B.
Using Tone-Out
111
Download from Www.Somanuals.com. All Manuals Search And Download.
•
Set Delay Time — Sets the time the scanner
remains in monitor mode after the scanner
receives a page and the carrier drops.
•
1-5 seconds: the scanner resumes standby
mode after the carrier drops and the selected
time expires.
•
•
Infinite: you must press HOLD after a page to
resume standby mode.
Off: the scanner resumes standby as soon as
the carrier drops after a page.
•
•
Set Alert — Sets the alert the scanner uses
when it receives an alert .
Alert 1 - 9, Off — scroll to select the
alert tone pattern, The scanner sounds each
alert as you scroll to its numbered value. If you
select Off , the scanner does not sound an
alert.
•
After you select an alert pattern, the scanner
prompts for the alert level for a received alert.
Level options 1 to 15 sets a fixed audio level
independent of the main volume setting. AUTO
uses the main volume setting for the alerts.
Using Tone-Out
112
Download from Www.Somanuals.com. All Manuals Search And Download.
Care And Maintenance
General Use
•
Turn the scanner off before disconnecting the
power.
•
•
If memory is lost, simply reprogram each channel.
Always press each button firmly until you hear the
entry tone for that key entry.
Location
•
•
•
Do not use the scanner in high-moisture
environments such as the kitchen or bathroom.
Avoid placing the unit in direct sunlight or near
heating elements or vents.
If the scanner receives strong interference or
electrical noise, move it or its antenna away from
the source of the noise. If possible, a higher
elevation might provide better reception.
•
Also try changing the height or angle of the
antenna.
Cleaning
•
Disconnect the power to the unit before cleaning.
•
Clean the outside of the scanner with a mild
detergent.
•
•
To prevent scratches, do not use abrasive
cleaners or solvents. Be careful not to rub the LCD
window.
Do not use excessive amounts of water.
Care and Maintenance
113
Download from Www.Somanuals.com. All Manuals Search And Download.
Repairs
Do not attempt any repair. The scanner contains no
user serviceable parts. Visit www.uniden.com.au (for
Australia) or www.uniden.co.nz (for New Zealand) to
contact customer support.
Birdies
All radios can receive “birdies” (undesired signals).
If your scanner stops during Scan mode and no sound
is heard, it might be receiving a birdie. Birdies are
internally generated signals inherent in the electronics
of the scanner.
Press L/O to lock out the channel.
Care and Maintenance
114
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
If your UBCD396T is not performing properly, try
these steps.
Problem Poss ible Cause
Sugge stion
The
The scanner might Make sure the AC
scanner
doesn’t
work.
not be receiving
any power.
adaptor is connected to
an AC outlet and the
scanner.
If there is a wall switch
that controls power to
the AC outlet where
you connected the AC
adaptor, make sure it is
on.
Improper
reception. might need to be
adjusted.
The antenna
Check the antenna
connection or move or
reposition the antenna.
Move the scanner.
You might be in a remote
area that could require
an optional multi-band
antenna. Check with
your dealer or local
electronics store.
Scan
won’t
stop.
The squelch might Adjust the squelch
need to be
adjusted.
threshold. See “Turning
On the Scanner and
Setting the Squelch” on
Page 38.
The antenna
might need to be
adjusted.
Check the antenna
connection.
One or more Make sure the
channels might be channels you want to
locked out.
scan are not locked
out.
The channel’s
frequency might
not be stored in
memory.
Make sure the
channel’s frequency is
stored in the scanner’s
memory.
The channel might Wait for a transmission
not be active.
on the channel.
Scan
won’t
start.
You must press
Scan to scan.
Press Scan.
Troubleshooting
115
Download from Www.Somanuals.com. All Manuals Search And Download.
Scan
won’t
start.
The squelch might Adjust the squelch
need to be
adjusted.
threshold. See “Turning
On the Scanner and
Setting the Squelch” on
Page 38.
(continued)
One or more Make sure the
channels might be channels you want to
locked out.
scan are not locked
out.
The antenna
might need to be
adjusted.
Check the antenna
connection.
If you experience difficulty while in TrunkTracker™
mode, try the following steps.
Problem Possible Cause
Suggestion
Scanner
won’t
track a
trunked
system.
The system might
not be one your
scanner can scan.
Scan another system.
The data
frequency might
be missing.
Enter the data
frequency.
The scanner might Change to a Type 1
need to be scanner setup. Review
changed to aType “Programming
1 scanner setup. Motorola Systems” on
Page 59.
Troubleshooting
116
Download from Www.Somanuals.com. All Manuals Search And Download.
Scanner
won’t
track a
trunked
system.
The system you
are trying to scan
might be LTR or
EDACS.
Set the scanner to
scan LTR or EDACS
systems. Review
“Programming LTR
Systems” on Page 66
and “Programming
EDACS Systems” on
Page 63.
(continued)
Scanner
No ID’s have been Program one or more
ID’s or use the ID
Search mode.
won’t stop programmed.
scanning
a trunked
system.
The ID’s you have Wait for the ID’s to
stored are not
active.
become active or scan
another system.
Scanner
won’t
acquire
the data
channel.
The squelch might Adjust the squelch
need to be
adjusted.
threshold. See
“Turning On the
Scanner and Setting
the Squelch” on
Page 38.
The frequency
used for the data
channel might be
missing.
Check your frequency
list for the data
channel.
Missing
replies to
conver-
sations.
The scanner might Change to a Type 1
need to be scanner setup. See
changed to a Type “Programming
1 scanner setup.
Motorola Systems” on
Page 59.
The fleet map
Try another preset fleet
might be incorrect. map or program your
own fleet map.
One or more of
the system’s
frequencies might
not be entered.
Make sure all the
system’s frequencies
have been entered.
The system you
are trying to scan
might be LTR or
EDACS.
Set the scanner to
scan LTR or EDACS
systems. Review
“Programming LTR
Systems” on Page 66
and “Programming
EDACS Systems” on
Page 63.
Troubleshooting
117
Download from Www.Somanuals.com. All Manuals Search And Download.
If you still cannot get satisfactory results while using
your scanner or if you want additional information,
please contact or write the Uniden Parts and Service
Division.
The address and contact number are listed in the
Warranty at the end of this manual.
If you have Internet access, you can visit
www.uniden.com.au (Australia) or www.uniden.co.nz
(New Zealand) for additional information.
Troubleshooting
118
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Dynamic Allocation Capacity
Systems: 400 max
Groups: 20 per system
Channels: up to 6000 (3000 typical)
Channels per Trunked System: up to 200
Attenuation: 18 dB (nominal), 10 dB (limit)
Frequency Range (MHz):
25.0 - 27.995
137.0 - 147.995
Above bands in 5 kHz steps
400.0 - 512.0
Above band in 6.25 kHz steps
28.0 - 69.990
Above band in 10 kHz steps
70.0 - 87.9875
108.0 - 136.9875
148.0 - 173.9875
764.0 - 775.9875
794.0 - 805.9875
806.0 - 956.0 “800”
1240.0 - 1300.0
Above bands in 12.5 kHz steps
225.0 - 399.95
Above band in 50 kHz steps
88.0 - 107.90
Specifications
119
Download from Www.Somanuals.com. All Manuals Search And Download.
174.0 - 224.90
Above bands in 100 kHz steps
Operating Temperature:
Normal –20°C to +60°C
Close Call –10°C to +60°C
Scan Rate: 100 channels per second
(conventional mode)
Search Rate: 300 steps per second (5 kHz step only)
Scan Delay: 0-5 seconds
Audio Output: 400mW nominal into 24 W internal
speaker
30 mW nominal into 32 W headphone
6 mW nominal into 64 W earphone
Power Requirements:
3 AA Alkaline Batteries (4.5V DC),
or 3 AA Rechargeable Ni-MH Batteries (3.6V DC),
or AC Adaptor (6 VDC 800mA) (AAD-396S)
Antenna: 50 W (Impedance)
External Jacks:
Antenna Jack SMA Type
Headphone Jack 3.5mm
DC Power Jack (EIAJ TYPE-2 Center Positive) 4 mm
Remote Jack 4 Pin Mini
Size: 61mm (W) x 31mm (D) x 136mm (H)
Specifications
120
Download from Www.Somanuals.com. All Manuals Search And Download.
Weight: 260g (with batteries installed)
175g (without batteries installed)
Features, specifications, and availability of optional
accessories are all subject to change without notice.
Specifications
121
Download from Www.Somanuals.com. All Manuals Search And Download.
Optional Accessories
Visit www.uniden.com.au (for Australia) or
www.uniden.co.nz (for New Zealand), for information
about ordering these optional accessories.
Earphone
Þ
External Amplified Speaker
Optional Accessories
122
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Preset Fleet Maps
Appendix
Preset Map 1
Preset Map 2
Bloc k
Size Code
Block
Size Code
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
Size Code 4
Size Code 4
Size Code 4
Size Code 4
Size Code 4
Size Code 4
Size Code 4
Size Code 4
Size Code 11
Size Code 11
Size Code 11
Size Code 11
Size Code 11
Size Code 11
Size Code 11
Size Code 11
Preset Map 3
Preset Map 4
Bloc k
S ize Code
Block
Size Code
0
1
2
3
4
5
6
7
S ize Code 4
S ize Code 4
S ize Code 4
S ize Code 4
S ize Code 4
S ize Code 4
S ize Code 12
(Size Code 12)
0
1
2
3
4
5
6
7
Size Code 12
(Size Code 12)
Size Code 4
Size Code 4
Size Code 4
Size Code 4
Size Code 4
Size Code 4
Preset Map 5
Preset Map 6
Bloc k
S ize Code
Block
S ize Code
0
1
2
3
4
5
6
7
S ize Code 4
S ize Code 4
S ize Code 12
(Size Code 12)
S ize Code 4
S ize Code 4
S ize Code 4
S ize Code 4
0
1
2
3
4
5
6
7
Size Code 3
Size Code10
S ize Code4
Size Code 4
Size Code12
(Size Co de 12)
Size Code12
(Size Co de 12)
Preset Map 7
Preset Map 8
Bloc k
Size Code
Bloc k
Size Code
0
1
2
3
4
5
6
7
Size Code 10
Size Code 10
Size Code 11
Size Code 4
Size Code 4
Size Code 4
Size Code 4
Size Code 4
0
1
2
3
4
5
6
7
Size Code 1
Size Code 1
Size Code 2
Size Code 2
Size Code 3
Size Code 3
Size Code 4
Size Code 4
Appendix
123
Download from Www.Somanuals.com. All Manuals Search And Download.
Preset Map9
Preset Map 10
Block
Size Code
Block
Size Code
0
1
2
3
4
5
6
7
Size Code 4
Size Code 4
Size Code 0
Size Code 0
Size Code 0
Size Code 0
Size Code 0
Size Code 0
0
1
2
3
4
5
6
7
Size Code 0
Size Code 0
Size Code 0
Size Code 0
Size Code 0
Size Code 0
Size Code 4
Size Code 4
Preset Map 11
Preset Map 12
Bloc k
Size Code
Block
Size Code
0
1
2
3
4
5
6
7
Size Code 4
Size Code 0
Size Code 0
Size Code 0
Size Code 0
Size Code 0
Size Code 0
Size Code 0
0
1
2
3
4
5
6
7
Size Code 0
Size Code 0
Size Code 0
Size Code 0
Size Code 0
Size Code 0
Size Code 0
Size Code 4
Preset Map 13
Preset Map 14
Block
Size Code
Block
Size Code
0
1
2
3
4
5
6
7
Size Code 3
Size Code 3
Size Code 11
Size Code 4
Size Code 4
Size Code 0
Size Code 0
Size Code 0
0
1
2
3
4
5
6
7
Size Code 4
Size Code 3
Size Code 10
Size Code 4
Size Code 4
Size Code 4
Size Code 12
(Size Code 12)
Preset Map 15
Preset Map 16
Block
Size Code
Block
Size Code
0
1
2
3
4
5
6
7
Size Code 4
Size Code 4
Size Code 4
Size Code 11
Size Code 11
Size Code 0
Size Code 12
(Size Code 12)
0
1
2
3
4
5
6
7
Size Code 3
Size Code 10
Size Code 10
Size Code 11
Size Code 0
Size Code 0
Size Code 12
(Size Code 12)
Appendix
124
Download from Www.Somanuals.com. All Manuals Search And Download.
User Defined Fleet Maps
Type I Programming Information
When a Type I system is designed, the address
information for all the ID’s is divided into 8 equal sized
blocks, numbered 0–7. When you program your
scanner to track a Type I system, you must select a
size code for each of these blocks. When you have
assigned a size code to all 8 blocks, you’ll have
defined the fleet map for the system you are tracking.
Each size code determines the number of fleets, sub-
fleets, and ID’s each block will have. For example, a
size code of S-4 has one fleet, which is divided into 16
separate subfleets, and it has a total of 512 individual
ID’s.
When a block is assigned a size code, the fleet or
fleets created within the block are assigned a Type I
ID. The way these ID’s display on your scanner
depend on the block number and the block’s size
code. When a Type I ID appears, the leftmost digit
represents the block which contains the ID.
The next 2-3 digits identify which fleet is active, and
the last digit(s) identifies the subfleet.
The details concerning how the size codes are
selected by a Type I System designer are highly
dependent on the specific needs of the system’s
users. Some organizations might want many subfleets
with only a few radios each, while another
organisation might want only a few subfleets with
many radios each. Your task is to program your fleet
map with the same size code assignments as the
trunked system. If you do this accurately, you’ll track
all the Fleet-Sub-fleet combinations used by the
system. In other words, you’ll hear complete
communications while monitoring a trunked system.
If you don’t already know the size codes used, you’ll
have to guess at them. But since you don’t have to
figure out all the blocks at once, this isn’t as hard as it
seems. Select a size code for a block, and then press
Scan. Now listen to the communications. If you decide
you are receiving most of the replies to the
Appendix
125
Download from Www.Somanuals.com. All Manuals Search And Download.
conversations with ID’s assigned to the block you just
programmed, then you’ve probably selected the right
size code and can work on the next block of the map.
Finally, for most public safety systems there are some
size codes which are more common. S-3 and S-4 are
probably the most common, followed by S-10, S-11,
and S-12.
Size Code Restrictions
If you select size code S-12, S-13, or S-14, there are
some restrictions as to which blocks can be used for
these codes.
S-12 can only be assigned to Blocks 0, 2, 4, or 6.
S-13 can only be assigned to Blocks 0 and 4.
S-14 can only be assigned to Block 0.
Since these size codes require multiple blocks, you
will be prompted for the next available block when
pro-gramming a fleet map. For example, if you assign
Block 0 as an S-12, you will be prompted for b2, the
next block available, instead of b1. And if you assign
Block 0 as an S-14, you would not see another prompt
because it uses all available blocks.
Appendix
126
Download from Www.Somanuals.com. All Manuals Search And Download.
Planning
Collecting Information
Getting your scanner programmed and scanning
takes a few steps. This helps guide you through these
steps that will make it easier for you to start scanning.
1. Collect information about the system(s) you want
to monitor.
Do you want to listen to your local police and
fire departments? How about the highway
patrol, ambulance service, and aircraft? You
might even want to listen to your local utility
company as they track down a break in
electrical service in your area.
Make a list of the agencies you want to listen to,
then look up the frequencies and systems used
by those agencies. The Internet is a great
source for current frequencies and information
about scanning.
Tips:
•
Scanners are designed to monitor complex radio
systems. That means that programming your
scanner might seem like a daunting task at first.
Be patient if you don't get it right the first time. You
can also seek out help locally for the systems you
want to scan by visiting the forums section of
http://www.radioreference.com/forums.
•
Before you start to program your scanner, decide
how you want to organize the frequencies you
want to scan. For example, some areas are best
organized by geographic location (east, north,
south, west, central, etc), while others are best
organized by agency (police, sheriff, ambulance,
fire, etc.). You might even find it easier to organize
a mixture of frequencies (north, southeast, and
west for police but fire all in one group for
example).
2. Organize the system information using these
system worksheets included in this appendix.
Planning
127
Download from Www.Somanuals.com. All Manuals Search And Download.
•
•
•
Use “Filling Out The Conventional System Work-
sheet” on Page 129 to organize info about
conventional frequencies.
Use “Filling Out The Motorola Worksheet” on
Page 130 to organize information about Motorola
frequencies.
Use “LTR/EDACS System Worksheet” on
Page 136 to organize information about LTR and
EDACS frequencies.
3. Follow the instructions in “Filling Out The
Conventional System Worksheet” on Page 129,
“Filling Out The Motorola Worksheet” on Page
130, and “Filling Out the LTR and EDACS
Worksheet” on Page 132 to program your scanner.
Tips:
•
•
•
Before you start, make as many copies of the
worksheets as you think you'll need.
All worksheet instructions assume that you have
completed the critical Step 1 (collecting the system
information). Don't skip this step.
Use a pencil to fill out the worksheets. This lets
you change information if necessary.
Planning
128
Download from Www.Somanuals.com. All Manuals Search And Download.
Filling Out The Conventional
System Worksheet
System Name and Quick Key
Fill in a name that describes the system you want to
create. For example, you can enter "Brisbane Police"
or "Amateur Radio" here. If you want to store more
than one type of frequency, you can enter "Mixed."
Fill in the key you want to press to quickly activate/
deactivate the system. You can assign the same quick
key to multiple systems.
Group Name and Quick Key
Each worksheet documents the settings for one
channel group within a system. If you have fewer
channels in the group than fits on the page, you can
skip a line and enter an additional group of channels
(enter the group info in the line you skipped). If you
have more channels for the group than will fit on the
page, use additional pages.
Fill in the key you want to press
with to quickly
activate/deactivate the channel group. You can assign
the same quick key to multiple groups within a
system.
Frequency-Alpha Tag-Priority-
CTCSS/DCS
Fill in the details for each channel you want to store in
this channel group.
Planning
129
Download from Www.Somanuals.com. All Manuals Search And Download.
Filling Out The Motorola Worksheet
System Name and Quick Key
Fill in a name that describes the system you want to
create. For example, you can enter "Brisbane Police"
or "Amateur Radio" here. If you want to store more
than one type of frequency, you can enter "Mixed."
Fill in the key you want to press to quickly activate/
deactivate the system. You can assign the same quick
key to multiple systems.
System Type
Circle in the type of Motorola system you are
scanning.
•
•
Type 1. A fleet map is supplied for this type of
system.
Type 2 800 MHz Standard. Used for most 800
MHz systems. No fleet map is supplied for this
type of system.
•
•
Type 2 800 MHz Splinter. Used for some 800 MHz
systems near border areas.
Type 2 900 MHz. The supplied frequencies are
between 935.0125 MHz and 939.9875 MHz.
No fleet map is supplied for this type of system.
•
•
•
Type 2 UHF. The supplied frequencies are
between 406 MHz and 512 MHz. No fleet map is
supplied for this type of system.
Type 2 VHF. The supplied frequencies are
between 136 MHz and 174 MHz. No fleet map is
supplied for this type of system.
P25. No fleet map is supplied for this type of
system.
Planning
130
Download from Www.Somanuals.com. All Manuals Search And Download.
System Frequencies
Enter the frequencies used by the system. Motorola
systems can use up to 28 frequencies. Place an
asterisk or other mark next to frequencies identified as
data channels.
Fleet Map (Type I or Type I/Type II
Hybrid Only)
Fill in the fleet map used by this agency.
Band Plan (VHF/UHF and P25 only)
For Motorola VHF/UHF system
A band plan is required so the scanner can correctly
determine the voice channel frequency. Fill in the band plan
used by this agency, consisting of:
•
•
•
Base frequency
Step frequency
Channel offset
You can enter up to three band plans.
For Motorola P25 system
Usually, the scanner stores the band plan automatically
when it receives the band plan from a repeater. Therefore,
the user doesn't have to set the band plan in most systems.
The plan must be set manually only when the repeater
doesn’t send the band plan. If you set the band plan
manually, it is necessary to input the following item.
•
•
Base frequency
Step frequency
Group Name and Quick Key
Each “Motorola System Worksheet 2” documents the
settings for one channel group within a system. If you
have fewer channels in the group than fits on the
page, you can skip a line and enter an additional
group of channels (enter the group information in the
line you skipped). If you have more channels for the
group than will fit on the page, use additional pages.
Fill in the key you want to press with to quickly
activate/deactivate the channel group. You can assign
the same quick key to multiple groups within a system.
Talk Group ID-Alpha Tag-Alert
Fill in the details for each channel you want to store in
this channel group.
Planning
131
Download from Www.Somanuals.com. All Manuals Search And Download.
Filling Out the LTR and EDACS
Worksheet
System Name and Quick Key
Fill in a name that describes the system you want to
create. For example, you can enter "Brisbane Police"
or "Amateur Radio" here. If you want to store more
than one type of frequency, you can enter "Mixed."
Fill in the key you want to press to quickly activate/
deactivate the system. You can assign the same quick
key to multiple systems.
System Frequencies and LCN
Fill in each system frequency and its associated
Logical Channel Number (LCN).
Group Name and Quick Key
Each “LTR/EDACS System Worksheet 2” documents
the settings for one channel group within a system. If
you have fewer channels in the group than fits on the
page, you can skip a line and enter an additional
group of channels (enter the group information in the
line you skipped). If you have more channels for the
group than will fit on the page, use additional pages.
Fill in the key you want to press with
to quickly
activate/deactivate the channel group. You can assign
the same quick key to multiple groups within a
system.
Talk Group ID-Alpha Tag-Alert
Fill in the details for each channel you want to store in
this channel group.
Planning
132
Download from Www.Somanuals.com. All Manuals Search And Download.
Conventional System Worksheet
Conventional System Worksheet
System Name
Group Name
System Quick Key
Group Quick Key
Frequency
Alpha Tag
Priority CTCSS/DCS
Planning
133
Download from Www.Somanuals.com. All Manuals Search And Download.
Motorola System Worksheet
Motorola System Worksheet 1
System Name
System Quick Key
Type I
System
Type II 800 MHz:
Standard
Frequencies
Splinter
Type II UHF
Type II VHF
Type II 900MHz
P25
Fleet Map
Block 0
Block 1
Block 2
Block 3
Block 4
Block 5
Block 6
Block 7
Band Plan A
Base Frequency
Step Frequency
Offset
Band Plan B
Base Frequency
Step Frequency
Offset
Band Plan C
Base Frequency
Step Frequency
Offset
Planning
134
Download from Www.Somanuals.com. All Manuals Search And Download.
Motorola System Worksheet 2
System Name
Group Name
Group Quick Key
Talk Group ID Alpha Tag
Alert
Planning
135
Download from Www.Somanuals.com. All Manuals Search And Download.
LTR/EDACS System Worksheet
LTR/EDACS System Worksheet 1
System Name
System Quick Key
System
Logical
Frequency
Channel
Planning
136
Download from Www.Somanuals.com. All Manuals Search And Download.
LTR/EDACS System Worksheet 2
System Name
Group Name
Sys tem Quick Key
Group Quick Key
Talk Group ID Alpha Tag
Alert
Planning
137
Download from Www.Somanuals.com. All Manuals Search And Download.
Warranty
One Year Limited Warranty
IMPORTANT: Evidence of the original purchase is required for warranty
service.
WARRANTOR: Uniden Australia Pty Ltd. ABN 58 001 865 498
Uniden New Zealand Limited.
ELEMENTS OF WARRANTY: Uniden warrants to the original retail owner for
the duration of this warranty its UBCD396T (hereinafter referred to as the
Product), to be free from defects in materials and craftsmanship with only the
limitations or exclusions set out below.
WARRANTY DURATION: This warranty to the original retail owner only is
only valid in the original country of purchase and shall be of no further effect
1 year after the date of original retail sale. This warranty will be deemed
invalid if the Product is: (A) Damaged or not maintained as reasonable and
necessary, (B) Modified, altered or used as part of any conversion kits,
subassemblies, or any configurations not sold by Uniden, (C) Improperly
installed, (D) Repaired by someone other than an authorized Uniden Repair
Agent for a defect or malfunction covered by this warranty, (E) Used in
conjunction with any equipment or parts or as a part of a system not
manufactured by Uniden. (F) Only available in the original country of sale.
PARTS COVERED: This warranty covers for one (1) year, the UBCD396T
Scanner only. All accessories (AC adaptor, batteries etc.) are covered for 90
days only.
STATEMENT OF REMEDY: In the event that the Product does not conform to
this warranty at any time while this warranty is in effect, the warrantor, at its
discretion, will repair the defect or replace the Product and return it to you
without charge for parts and service. THIS WARRANTY DOES NOT COVER OR
PROVIDE FOR THE REIMBURSEMENT OR PAYMENT OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES. THIS GUARANTEE IS IN ADDITION TO AND DOES
NOT IN ANY WAY AFFECT YOUR RIGHTS UNDER THE CONSUMER GUARANTEE
ACT.
PROCEDURE FOR OBTAINING PERFORMANCE OF WARRANTY: in the
event that the Product does not conform to this warranty, the Product should
be shipped or delivered, freight prepaid, with evidence of original purchase
(e.g. a copy of the sales docket) to the warrantor at:
UNIDEN AUSTRALIA PTY LIMITED
SERVICE DIVISION
345 Princes Highway,
Rockdale,
UNIDEN NEW ZEALAND LIMITED
SERVICE DIVISION
150 Harris Road,
East Tamaki,
NSW 2216,
AUSTRALIA
Auckland,
NEW ZEALAND
Fax: (02) 9599 3278
www.uniden.com.au
Fax: (09) 274 4253
www.uniden.co.nz
Planning
138
Download from Www.Somanuals.com. All Manuals Search And Download.
©2006 Uniden Australia Pty Limited, Uniden New Zealand Limited.
Printed in China.
UBZZ01328AZ(0)
Download from Www.Somanuals.com. All Manuals Search And Download.
|