UIP1868P Router Configuration Guide
The UIP1868P can function as your primary gateway/router or as a device
client within an existing network configuration.
If you currently have broadband access and a gateway/router installed at
your location, you may add the UIP1868P as a device client to your
network. (See“A”below.) If you currently have broadband internet access
and do not have a router, you may install your UIP1868P as the primary
router to your network. (See“B”below.)
A Installing the UIP1868P with an existing network
configuration/router
Computer
Broadband
modem
Local router
Internet
UIP1868P
Plug one end of the enclosed Ethernet cable into the WAN port on the
back of the UIP1868P. Plug the other end of the Ethernet cable into your
router/gateway which is connected to your broadband modem.The
UIP1868P will automatically obtain an IP address from your existing
router.
B Installing the UIP1868P as your primary gateway/router
Broadband
modem
UIP1868P
Computer
Local switch
or router
Internet
The UIP1868P supports the two most common broadband connection
protocols: DHCP (most common connection type found with Cable
Modem) and PPPoE (most DSL providers use this connection type).
Download from Www.Somanuals.com. All Manuals Search And Download.
1
2
Setting up with DHCP
The UIP1868P is configured for use with Dynamic Host Configuration
Protocol (DHCP) by default. If your broadband connection uses DHCP,
simply connect your broadband modem to the WAN port of the
phone and then connect the phone’s power cord to an AC power
outlet.
Setting up with PPPoE
If your broadband connection uses PPPoE, you will need to configure
the UIP1868P built-in router by inputting the user name and password
provided by your Internet Service Provider. Follow the steps below to
configure the UIP1868P to use a PPPoE-based connection.
a) Connect a
computer with a
web browser
Figure #1
directly to the LAN
port of your UIP1868P.
(the default IP address of
your UIP1868P) into the
address bar of your web
browser.Then press the
Enter key. (See Figure #1)
c) You should now see your
Figure #2
UIP1868P’s System
Information Screen.
(See Figure #2)
d) In the menu bar down the left
side of the screen, select WAN.
e) In the menu bar on the top of
the screen, select PPPoE.This
opens the WAN PPPoE
Configuration screen.
(See Figure #3)
Figure #3
Download from Www.Somanuals.com. All Manuals Search And Download.
f) Under ENABLE PPPOE, click the drop-down arrow and
select YES.
g) Under Authentication, enter the USERNAME and PASSWORD
that were provided by your ISP. Username and password are
often case-sensitive, so be sure to enter upper and lower case
letters correctly.
h) Under Settings, select the radio button labeled KEEPALIVE.This
configures the phone to maintain the PPPoE connection even
when your computer is idle or turned off.
i) When the utility displays a window telling you it must reboot
the phone, make sure your broadband modem is connected to
your phone's WAN port, then click
OK.When the phone finishes
rebooting, it will ask your
broadband modem to assign an IP
address. (See Figure #4)
Figure #4
NOTE: For detailed installation with PPPoE, please refer to UIP1868P User Interface Guide – Setting
up with PPPoE section.
C Setting up with a Static IP Address
If your broadband provider has given you a static IP address, you will need
to enter that information in the UIP1868P. Follow the steps below to
configure the UIP1868P for use with a Static IP address.
Connect a computer with a web browser directly to the LAN port of
your UIP1868P.
(the default IP address of
your UIP1868P) into the
Figure #5
address bar of your web
browser.Then press the Enter key.
(See Figure #5)
You should now see your
UIP1868P’s System Information
Screen.
(See Figure #6)
Figure #6
Download from Www.Somanuals.com. All Manuals Search And Download.
In the menu bar down the left side of the
screen, select WAN.
In the top menu bar, select WAN Settings.This
will open the WAN Configuration screen.
(See Figure #7)
Select the radio button labeled SPECIFY FIXED
WAN CONFIGURATION.
Figure #7
Enter the IP Address, Subnet Mask, and Gateway Address provided by
your ISP.
Click SAVE WAN CONFIGURATION.
When the utility displays a window telling you it must reboot the
phone, make sure your broadband modem is connected to your
phone's WAN port, then click OK.When the phone finishes rebooting,
it will ask your broadband modem to assign an IP address.
(See Figure #8)
NOTE: For detailed installation with a Static IP
address, please refer to the UIP1868P User
Interface Guide – WAN Configuration section.
Figure #8
You are now ready to activate your Packet8 account. (Please refer to
the Uniden Quick Start Guide instructions for activating your Packet8
account.)
You can download a copy of the UIP1868P User Interface Guide at
UPZZ76747EZ(0)
Download from Www.Somanuals.com. All Manuals Search And Download.
Packet8 Broadband Phone Service Reference Card
Calling with Packet8 service—
just like using your home or cell telephone
To call anywhere in the world, dial: country code + area code + number.
Example: the country code for the U.S. and Canada is “1.”
Dial: 1+area code+number.
Anyone can call you at your Packet8 phone number.
Using the Features of your Packet8 service
Advanced Call Features: these features are activated with the [Flash] key
on your phone (or going on-hook for half second then going off-hook):
• Caller ID: automatic when presented.
• Call Waiting: a beep is heard when there is an incoming call.
Answer the incoming call by pressing the [Flash] key.
• Line-alternate/Hold: press the [Flash] key to put the current line on hold.
• 3-way Conferencing: during a call, press [Flash], call third party,
then press [Flash] to conference. Press [Flash] again to drop the
last person added.
• *69 Call Return: press *69 and stay on the line to automatically ring
the last number that called your number.
• *70 Call Waiting Disable: to disable call waiting on a per-call basis,
enter *70 before dialing.You can disable call waiting and send new
callers to voicemail, or present a busy tone if voicemail is disabled
while you are on a phone call.
• *77 Anonymous Call Rejection (ACR): a feature that rejects incoming calls
from anonymous callers. It will automatically stop all incoming calls from
callers who have their numbers blocked.To de-activate ACR, press *87.
• *78 Do Not Disturb: automatically send your calls directly to your voice
messaging box without ringing your phone.You will hear a stutter tone on
your phone to indicate the feature is turned on.To de-activate, press *79.
• Call Forwarding: you can forward your phone to ring somewhere else.
Go to your account details page after signing in at www.packet8.net
or call from your Packet8 phone: 012-0005.
Communication for the
Broadband Generation
Download from Www.Somanuals.com. All Manuals Search And Download.
VoiceMail Reference Card
Using VoiceMail on your Packet8 service
To check your Packet8 voicemail:
• From your Packet8: 012-0555
• From any phone, toll-free:1.888.898.7887
• From any phone outside the U.S.: 1.650.353.4400
When prompted, enter your Packet8 phone number (1+area
code+number) and then your password
1
2
3
4
Next message
If you have a message waiting, you can press:
Replay message
Delete message
If you do not have a message waiting,
you can press:
Save messages and
listen to the next
1
8
Voicemail Preferences
Listen to Saved Message
1
2
#
Hear greeting
1
2
3
4
Next message
Delete and re-record greeting
Put new greeting in service
Replay message
Delete message
Send message as email
There are two ways to change your voicemail settings, voicemail
password, number of rings, and call settings:
• Call from your Packet8: 012-0005
When prompted, enter your Packet8 phone number, then your password
Telephone keypad map for changing your Packet8 account settings:
1
2
3
Voicemail
Call Settings
Personal Access
Password
1
2
1
2
3
1
2
Voicemail
Settings
Ring Before
Voicemail
Answers
Call
Forwarding
Int’l
Caller ID
Enable
Password
Re-enter
Password
Calling
1
2
On
Off
1
On
1
On
1
On
1
-
9
2
Off
2
Off
2
Off
Packet8 Contact Information:
Support:
•
Automated Activation Service: 012-0001
•
• Customer Service,toll-free:1.888.898.8733
Customer Service,outside U.S.:1.408.687.4120
•
Automated IP Address/Phone Number
Service: 012-0003
•
•
Packet8 Voicemail: 012-0555
3151 Jay Street
Santa Clara, CA U.S.A. 95054
Tel: 408.727.1885 • Fax: 408.980.0432
w
Packet8, the Packet8 logo, and the 8x8, Inc. logo are registered trademarks of 8x8, Inc. 8x8, Inc. is a Nasdaq listed company, symbol EGHT.
© 2005. 8x8, Inc. All rights reserved. QRC4001 0205
Download from Www.Somanuals.com. All Manuals Search And Download.
|