USE AND CARE GUIDE
®
2000 SERIES
CLEAR ICE MODELS
CLEAR COMBO® MODELS
CLEAR COMBO® MODELS
CLEAR ICE
U-CLR2160B-00
U-CLR2160B-40
U-CLR2160S-00
U-CLR2160S-01
U-CLR2160S-40
U-CLR2160S-41
U-CLR2160SOD-00
U-CLR2160SOD-01
U-CLR2160SOD-40
U-CLR2160SOD-41
U-CLR2160W-00
U-CLR2160W-40
U-CLRCO2175B-00
U-CLRCO2175B-40
U-CLRCO2175S-00
U-CLRCO2175S-01
U-CLRCO2175S-40
U-CLRCO2175S-41
The American Built-In Undercounter Leader Since 1962
U-LINE.COM
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Safety Precautions
Safety Alert Definitions ........................................................................................................................................1
General Precautions .............................................................................................................................................1
Product Features
Model Features: .....................................................................................................................................................2
Combo® Model Features: ..................................................................................................................................2
Product Operation
Air Flow ...................................................................................................................................................................3
Initial Startup ..........................................................................................................................................................3
Electronic Control Panel .....................................................................................................................................3
Adjusting Air Temperature CLRCO2175 .......................................................................................................3
Checking Product Temperature ........................................................................................................................4
Interior Lighting .....................................................................................................................................................4
Clean Alert .............................................................................................................................................................4
Electronic Control Quick Guide .......................................................................................................................5
Clear Ice Maker
Clear Ice Maker Cleaning Cycle ........................................................................................................................6
Refresh Kit ..............................................................................................................................................................7
Ice Cube Thickness Adjustment ........................................................................................................................7
Maintenance
Leveling ....................................................................................................................................................................8
Removing and Installing Interior Shelves .........................................................................................................8
Light Bulb Replacement .......................................................................................................................................8
Removing and Installing Grille ............................................................................................................................9
Removing and Installing Door Shelves .............................................................................................................9
Doors (Self-Closing)
Door Alignment and Adjustment ................................................................................................................... 10
Door Reversability ............................................................................................................................................. 10
Reversing Black or White Doors ................................................................................................................... 11
Reversing Stainless Steel Glass Doors .......................................................................................................... 12
Cleaning
Exterior Cleaning ............................................................................................................................................... 15
Interior Cleaning ................................................................................................................................................ 15
Defrosting ............................................................................................................................................................ 15
Condenser Cleaning .......................................................................................................................................... 16
Storage, Vacation and Moving ......................................................................................................................... 16
Product Disposal ................................................................................................................................................ 16
Service
Before Calling for Service ................................................................................................................................ 17
If Service is Required ......................................................................................................................................... 17
Replacement Parts ............................................................................................................................................. 17
Normal Operating Sounds ............................................................................................................................... 17
Troubleshooting Guide ..................................................................................................................................... 17
Download from Www.Somanuals.com. All Manuals Search And Download.
General Precautions
Safety Precautions
Use this appliance for its intended purpose only. Follow these
general precautions with those listed throughout this guide:
NOTICE
DANGER
• PLEASE READ all instructions before installing,
operating, or servicing the appliance.
!
RISK OF CHILD ENTRAPMENT. Before you throw away your
old refrigerator or freezer, take off the doors and leave shelves
in place so children may not easily climb inside.
• Proper installation procedures must be followed when
completing an installation or relocation of a unit. An
INSTALLATION GUIDE for the unit, providing
complete installation information, is available from
U-Line Corporation direct. Consult the installation
guide before any installation begins. U-Line contact
information appears on the rear cover of this guide.
WARNING
!
SHOCK HAZARD - Electrical Grounding Required.
• Never attempt to repair or perform maintenance on
the unit until the electricity has been disconnected.
• Never remove the round grounding prong from the
plug and never use a two-prong grounding adapter.
• Altering, cutting of power cord, removal of power
cord, removal of power plug, or direct wiring can
cause serious injury, fire and or loss of property and
or life, and will void the warranty.
• This unit requires connection to a dedicated 15 Amp
grounded (three-prong), polarized receptacle, installed
by a qualified electrician, compliant with applicable
electrical codes.
Safety Alert Definitions
• Never use an extension cord to connect power to the
unit.
• Always keep your working area dry.
Throughout this guide are safety items labeled with a Danger,
Warning or Caution based on the risk type:
DANGER
!
WARNING
!
Danger means that failure to follow this safety statement will
result in severe personal injury or death.
Install provided Anti-Tip kit. Serious personal injury
could occur.
WARNING
!
CAUTION
!
Warning means that failure to follow this safety
statement could result in serious personal injury or
death.
• Use care when moving and handling the unit. Use gloves
to prevent personal injury from sharp edges.
• If your model requires defrosting, DO NOT use an ice
pick or other sharp instrument to help speed up
defrosting. These instruments can puncture the inner
lining or damage the cooling unit. DO NOT use any type
of heater to defrost. Using a heater to speed up
defrosting can cause personal injury and damage to the
inner lining.
CAUTION
!
Caution means that failure to follow this safety statement
may result in minor or moderate personal injury, property
or equipment damage.
NOTICE
• Do not lift unit by door handle.
• Never install or operate the unit behind closed doors.
Be sure front grille is free of obstruction. Obstructing
free airflow can cause the unit to malfunction and will
void the warranty.
• Failure to clean the condenser every six months can
cause the unit to malfunction. This could void the
warranty.
• Do not Block any internal Fans.
Use only genuine U-Line replacement parts. Imitation
parts can damage the unit, affect its operation or
performance and may void the warranty.
u-line.com
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Combo® Model Features:
Product Features
Model Features:
Clear ice production capability plus refrigeration all in one
unit. Both clear ice capability and refrigeration all in on 24" wide
compact unit.
High daily ice production and storage. The CLR2160
produces up to 60 pounds of ice per day and stores up to 30
pounds. While the CLRCO2175 can produce up to 40 pounds of
ice per day and store up to 15 pounds.
Three glass shelves. Maximizes storage capacity and easy to
clean.
Two adjustable in-door storage shelves. Provides easy access
to commonly used product. Allows for flexible storage options.
Electronic control module. Automatically adjusts for changes
Recessed interior light. Located in the refrigerator, this light
in room and water temperatures to maximize ice production.
automatically illuminates when the door is open.
Digital controls. Provides an elegant interface and allows for
complete control over the self cleaning process, thickness of ice
cubes, and power control. The unit also provides temperature
control functions for the CLRCO2175.
Easy, self-cleaning process. Both models have a simple to use
self cleaning process. Within one hour all ice making internal
components have been thoroughly cleaned and rinsed.
Optional 3/4" full overlay door panel. Provides a fully
integrated appearance with surrounding décor while maintaining
zero clearance. (Black & White models).
1/4" panel. Models will also accept a 1/4" door panel to match
surrounding décor. (Black & White models)
Flexible water drain options. Water may be drained using
either a gravity fed drain or a U-Line supplied P60 drain pump.
Built in or freestanding. Provides custom look, no additional
clearance needed around top, rear or sides of unit.
Stainless steel model. Offers a stainless door along with a
commercial stainless door handle. Outdoor models also include a
stainless cabinet.
Self-closing door. Engages when door is open 8"-10" and ensures
a positive door seal. Also prevents door bounce back.
Field reversible doors. Flexible installation options. Allows your
unit to be installed almost anywhere.(Black & White models).
Integrated handle. Sleek designer look that does not add depth
to the cabinet when built in (Black & White models).
Vinyl-clad cabinets. Textured, rich look. More resistant to
scratching, peeling and flaking. (Black, White & Stainless Indoor
models).
Leveling legs. Provides a more precise under counter fit. Durable
and factory installed.
Sabbath or “Black Out” mode. Easily turn off all lights and
control display until manually reset.
Contemporary grille design. Integrates and accents
surrounding décor.
LED illumination. Provides efficient and elegant lighting to the
interior of your unit. Automatically illuminates when door is open
(CLR2160 indoor models only.).
2
u-line.com
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting Air Temperature
CLRCO2175
Product Operation
Air Flow
NOTICE
Adjust the set point temperature in single increments,
and wait 24 hours for the temperature to stabilize before
rechecking.
NOTICE
The unit requires proper air flow to perform at its highest
efficiency. Do not block the front grille or internal fans at
any time, or the unit will not perform as expected. Do not
install the unit behind a door.
1
2 3
4
5
Note: The CLRCO2175 refrigerator zone temperature is adjustable. The
ice storage bin temperature in the CLRCO2175 or CLR2160 is not
adjustable.
To adjust the set point temperature:
1. Press and release either WARMER
(2) or COOLER
(4)
Initial Startup
to put the controller in the SET TEMPERATURE mode. The
display (3) will begin to flash the °F (or °C) symbol.
All U-Line controls are preset at the factory. Initial startup requires
no adjustments.
NOTE: This mode will self-cancel in five seconds, and the
display (3) will show the original set point temperature.
NOTICE
2. Within five seconds (while the °F (or °C) symbol is flashing),
press WARMER
or COOLER
as required to adjust the
U-Line recommends allowing the unit to run overnight
before loading refrigerator or freezer with product.
set point temperature.
3. The change sets five seconds after adjusting the temperature,
and the display (3) will show the new set point temperature.
To turn the unit on or off, press and hold the POWER icon (1) for
about ten seconds and release. The display will show the unit set-
point temperature on Combo models, and ICE on Clear Ice
models when turned on and display “OFF” when the unit is off.
Temperature °F °C Selection. U-Line products supplied for
110 VAC have temperatures displayed (3) by default in Fahrenheit
(°F). Models supplied for 220 VAC have temperatures displayed (3)
by default in Celsius (°C).
Electronic Control Panel
Easily adjust the display for either type temperature display.
Digital Display. The electronic control with digital display on
Combo models shows a single continuous set-point temperature,
or on Clear Ice models it shows “ICE”. The set point is for the
middle zone, it is a base number used by the controller to maintain
the multiple temperature zones in the unit. The factory default set-
point for Refrigerator models is 38°F. The set-point temperature is
a gauge for further temperature adjustments.
1. Press and hold LIGHT
seconds press COOLER
display (3) as needed.
(1) and simultaneously within five
(5) three times to change the
Temperature Display. The digital display shows set-point. air
temperature. Under normal operating conditions the temperature
will fluctuate based on a number of factors including door
openings, product load, room temperature, and humidity. The
temperature will always be cool toward the top and coolest
toward the bottom.
To display actual temperature:
1. Press WARMER
(2) for five seconds. The display (3) will
indicate the actual temperature.
2. After about 10 seconds, the set point temperature will return to
the display.
u-line.com
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Checking Product Temperature
Interior Lighting
Normal Operation. Opening the door will cause the interior of
the cabinet to illuminate.
Use LIGHT
functions.
(5) on the control panel to change the lighting
1
2 3
4
5
Blackout (Sabbath) Mode. The interior of the cabinet and
control display remains darkened until reset. Blackout (Sabbath)
Mode is not Star K certified.
To turn the lights and display OFF.
To check the actual product temperature in the unit.
1. Partially fill a plastic (nonbreakable) bottle with water.
2. Insert an accurate thermometer.
1. Press and hold LIGHT
(5) for ten seconds and release (the
°F symbol will flash briefly at the end of the ten second period).
2. The interior light and control display (3) will go dark until the
mode is reset.
3. Tighten the bottle cap securely.
4. Place the bottle in the desired area for 24 hours.
5. Avoid opening the unit during the testing period.
3. NOTE: Although the display will not be visible, the temperature
controls in the unit remain active, and preserve the interior
temperature.
6. After 24 hours, check the temperature of the water. If required,
adjust the temperature control in a small increment (See
ADJUSTING TEMPERATURE).
To exit the Blackout (Sabbath) Mode, repeat Step 1.
Clean Alert
Causes which affect the internal temperatures of the
cabinet include:
Operation of the unit is continuously monitored by the electronic
control. The unit will automatically notify the user that the units
internal components require cleaning. When the alert is issued
“CL” will appear on the control display. For more information on
cleaning your ice maker see page 6.
•
•
•
•
•
Temperature setting.
Ambient temperature where installed.
Installation in direct sunlight or near a heat source.
The number of door openings and the time the door is open.
Note: The clean alert can be temporarily dismissed by touching any
key on the display.
The time the internal light is illuminated. This mainly affects
product on the top rack or shelf.
•
The front grille or condenser are obstructed.
4
u-line.com
Download from Www.Somanuals.com. All Manuals Search And Download.
Electronic Control Quick Guide
Task
Touch
Touch
Display
Comment
Turn ON/OFF
Hold 5 seconds
Release when °F flashes.
or
°F flashes after first touch,
set-point saved after 5
seconds of inactivity and °F
stops flashing.
or
or
Adjust
Temperature
CLRCO2175
Touch and release
Touch to change temperature
View Actual
Temp
WC models will scroll top/
mid/bottom temps.
Hold 5 seconds
Release when °F flashes.
CLRCO2175
Change F/C
CLRCO2175
Hold
or
Blackout will end in 36
hours, or hold again to
terminate early.
Display (and cabinet light) will not
operate in Blackout Mode.
Blackout Mode
Hold 10 seconds
Clear Ice & Clear ice Combo
Will automatically return to
ice production when clean
cycle is complete
Clean Cycle
Ice Thickness
Adjustment
Use warmer/colder to
scroll.
Temporar y
Shutdown
(Office Mode)
Ice maker will automatically
turn back on in three hours.
Combo Ice
Maker Off
Repeat to switch back
NOTE: 38°F is an example; the display will vary with actual set-point.
u-line.com
5
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Re-install the standpipe into the water trough.
Clear Ice Maker
Clear Ice Maker Cleaning Cycle
Units with a serial number beginning with an 09 or greater have an
automatic clean alert function. Cleaning cycles should be run as
notified. Otherwise, To maintain operational efficiency the unit
should be cleaned every three months. Depending on water
conditions, more frequent cleaning may be necessary. If the ice
maker requires more frequent cleaning, consult a plumber to test
the water quality and recommend appropriate treatment.
Evaporator
Standpipe
Water trough
CAUTION
!
6. Clean the Interior Bin as follows:
Wear rubber gloves and safety goggles and/or face shield
when handling Ice Machine Cleaner.
•
•
Dilute one packet of CLR cleaner into two quarts of water.
Using a sponge or cloth, clean interior of ice bin, tubing and
door. This cleaner will remove all mineral deposits and
other contaminants from the surfaces.
NOTICE
Use only U-Line Ice Machine Cleaner (Part No. 37050,
available from your dealer or direct from your local parts
distributor. To locate a parts distributor near you, visit
use this solution in a manner inconsistent with its labeling.
Use of any other cleaner can ruin the finish of the
evaporator and will void the warranty. Read and
•
Using a bottle brush, clean out the trough drain tube and
pump tubing where needed.
understand all labels printed on the package before use.
U-Line Ice Machine Cleaner is used to remove lime scale and other
mineral deposits. Refer to the following steps to initiate the self-
cleaning cycle.
Brush
NOTICE
• Model CLRCO2175 refrigerator will not operate during
the ice maker cleaning cycle. Remove all fresh food to
prevent spoilage.
7. Turn unit on by touching POWER
.
• Model CLRCO2175 ice production after the first
harvest may take longer after the cleaning cycle since
restoring the refrigerator temperature will take
precedence over ice production. Once the refrigerator
reaches its set-point temperature, ice making will
resume.
8. Place the unit into CLEAN mode by holding POWER
while
pressing LIGHT three times.
9. When water begins flowing over the evaporator (approximately
3 minutes), pour 1 packet of CLR cleaner into the water trough.
The cleaning process will last approximately 45 minutes.
10. Dilute 1 tablespoon bleach in 1 gallon of warm water. Apply this
solution to the entire inside of the storage area. Then rinse
thoroughly with water.
CAUTION
!
Evaporator cover
Never use anything to
force ice from the
evaporator. Damage may
result.
The unit will resume operation approximately 15 minutes after the
automated cleaning process is completed. The water fill valve will
energize, fill the water reservoir, and shut-off after three minutes.
The compressor begins to operate and water flows over the
evaporator assembly (ice mold). Initially, the water flow may not be
uniform, causing uneven sized cubes or water to spill into the ice
storage bin. This is a normal situation that will correct itself within
the first 24 hours of operation.
1. Turn the ice maker off and
allow any ice to melt off of
the evaporator.
2. Remove all ice from the
storage bin.
3. Remove evaporator cover.
4. Remove the standpipe by lifting it up while using a slight back and
forth motion to loosen it from the drain hole. The water in the
reservoir will flow down the drain.
6
u-line.com
Download from Www.Somanuals.com. All Manuals Search And Download.
Ice cubes in any given batch will vary, so it is necessary to choose
cubes from the sample area for comparison when making
adjustments. If further adjustments are desired, repeat Steps 1
through 4.
NOTICE
• Discard all ice produced in the first harvest.
• Should power to the unit be interrupted during the
self-clean cycle, it will be necessary to repeat the
complete cleaning cycle after power is restored.
The ice cube thickness is factory set for best overall performance.
The factory setting is designed to maintain an ice bridge of
approximately 1/16" to 1/8" under normal conditions, resulting in a
dimple of approximately 1/4" to 1/2" in depth. A fuller cube with
less of a dimple results in a thicker ice bridge. As the ice bridge
becomes thicker, the tendency for the cubes to stay together as a
slab increases. A bridge thicker than 1/8" may cause cubes to
overfill the ice bucket.
Refresh Kit
Due to variations in water quality or inadequate maintenance your
unit may become excessively coated in lime scale or calcium.
U-Line offers a cost effective refresh kit which replaces many
interior components and will return your unit to like new
condition. Refresh kits may be ordered from your local distributor
and installed by your local service company. For information on
your local distributor or service company please visit
DIMPLES
Refresh Kit Part Number
Model
Part Number
80-51003-00
80-51002-00
CLR2160
CLRCO2175
ICE BRIDGE
Ice Cube Thickness Adjustment
Interval - As Required
Ice Bridge and Dimples
Ice thickness adjustments are made using the control panel as
follows:
1. To enter the thickness adjustment mode:
CubeTypes
•
•
Touch and hold WARMER
Touch and release COOLER
.
1/16" TO 1/8"
ICE BRIDGE
1/4" TO 1/2"
DIMPLE
three times, then release
WARMER
.
•
The display will switch to “0” to confirm the thickness
adjustment mode has been selected.
2. The factory setting is “0,” and the total range of adjustment is -5
to +5 (ideal range is -1 to +1). Use WARMER
setting and thicken the ice bridge, or COOLER
setting to thin the ice bridge.
to raise the
to lower the
GOOD
NOTICE
Ice thickness adjustment should only be made one
increment at a time. Allow ice maker production to
stabilize for 24 hours before rechecking ice thickness.
BRIDGE
TOO THICK
BRIDGE
TOO THIN
DIMPLE
TOO DEEP
LITTLE OR
NO DIMPLE
3. Touch and release the LIGHT button key to exit the ice
thickness adjustment mode.
4. Remove all ice from the storage bin.
BAD
u-line.com
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Removing and Installing Interior Shelves
Maintenance
Leveling
1. Pull shelf out about 6" until back of shelf clears the “hump” on
the right-hand side.
2. Tilt right-hand edge of shelf
up. Remove shelf from unit by
pulling out.
NOTICE
Unit must be level, for proper door and ice maker (if
equipped) operation.
Insert the shelves as follows:
2
1. To move to a different
1
position in the unit, insert
shelf at an angle,
approximately 15°-20° over
the rib in the side of the unit
where you want to place the
shelf. The shelf must be
started into the unit at an
angle to clear the door.
2. Continue to slide the shelf
1
into the unit at an angle until free.
3. Lower the shelf and push it in completely.
Light Bulb Replacement
CLRCO2175 Only
For Models with adjustable leveling feet:
To replace the light bulb in your U-Line unit:
1. Use a level to check the levelness of the unit from front to back
and from side to side. Place the level along top edge and side
edge as shown (1).
1. Find the light located at the top of the unit. Grasp the edges of
the light housing lens (1), opposite the exposed tab, and gently
push the lens toward the tab (2).
2. If the unit is not level, rotate the adjustable leveling legs to raise
or lower each corner of the unit as necessary.
2. Pull the edge of the lens down (1) and swing it out of the light
housing.
3. Check levelness after each adjustment and repeat the previous
steps until the unit is level.
For Models without adjustable leveling feet:
2
1
NOTICE
The unit must be located on a level surface, for proper
door and ice maker (if equipped) operation.
Use a level to check the levelness of the unit from front to back
and from side to side. Place the level along top edge and side
edge as shown (1).
NOTICE
ALWAYS use a genuine U-Line replacement 120V 10 watt
bulb (Part Number 31317) in the light housing. Use of any
other bulb within the housing will produce excessive heat,
causing damage to the light housing and cabinet interior,
and will compromise the precise temperature control of
the unit.
3. Replace the lens by first inserting the tab side back into the
housing at a slight angle.
4. While gently pushing the lens towards the tab end, push the free
end into the housing, and release when you hear a snap.
8
u-line.com
Download from Www.Somanuals.com. All Manuals Search And Download.
Removing and Installing Grille
Removing and Installing Door Shelves
1
WARNING
!
Disconnect electric power to the unit before removing
the grille.
WARNING
!
DO NOT touch the condenser fins (4). The condenser
fins are SHARP and can be easily damaged.
Removing the grille.
1. Disconnect power to the unit.
2. Loosen the two screws (1).
3. Remove grille (2) from unit.
Installing the grille:
2
For models equipped with door shelves:
To remove the door shelf:
1. Place the hook-hinge located on the rear bottom side of the
grille (2) onto the front lip of the unit base. Swing the grille up
into position.
1. Grasp shelf in center, and lift until the shelf notches (1) clear
the pins (2).
2. Align cabinet and grill holes and secure, but do not overtighten
grille screws (1).
2. Carefully pull the shelf away from the door.
To install the door shelf:
3. Reconnect power to the unit.
1. Holding the shelf in the center, center the shelf in the door at
the desired location, slightly above the pins (2).
1
2. Lower the shelf onto the pins (2).
2
4
5
Typical Model Shown
u-line.com
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Doors (Self-Closing)
Door Alignment and Adjustment
Align and adjust the door if it is not level, or is not sealing properly.
If the door is not sealed the unit may not cool properly, or
excessive frost may form in the interior.
NOTICE
• Properly aligned, the door’s gasket should be firmly in
contact with the cabinet all the way around the door
(no gaps). Carefully examine the door’s gasket to
ensure that it is firmly in contact with the cabinet. Also
make sure the door gasket is not pinched on the hinge
side of the door.
• The door will not be flush with the top of the cabinet.
The top edge of the door will be 1/8 in. (3.175 mm)
below the cabinet top.
4
door is parallel with top of cabinet and tighten screws (1)
securely.
5. After adjustment is complete, remove the door closers from the
bottom hinge, clean thoroughly and apply petroleum jelly to the
mating surfaces of the closers. Be sure that pins on closers align
with holes in the door and bottom cabinet hinge plates. Mount
door and install top hinge pivot pin.
1/8"
(3.175 mm)
Door Reversability
Location of the unit may make it desirable to mount the door on
the opposite side of the cabinet. Many doors are reversible. See
table below.
Model
U-2115RB-00
U-2115RS-00
U-2115RS-01
Reverse
YES
NO
NO
NO
NO
NO
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
NO
NO
NO
YES
YES
NO
NO
YES
NO
NO
YES
Model
Reverse
YES
YES
YES
YES
YES
YES
YES
YES
NO
NO
NO
NO
NO
NO
NO
NO
YES
YES
YES
YES
NO
NO
NO
NO
YES
NO
NO
YES
U-2175WCCOL-02
U-2175WCCOL-60
U-2175WCCS-00
U-2175WCCS-02
U-2175WCCS-13
U-2175WCCS-22
U-CLR2160B-00
U-CLR2160B-40
U-CLR2160S-00
U-CLR2160S-01
U-CLR21060S-40
U-CLR2160S-41
U-CLR2160SOD-00
U-CLR2160SOD-01
U-CLR2160SOD-40
U-CLR2160SOD-41
U-CLR2160W-00
U-CLR2160W-40
U-CLRCO2175B-00
U-CLRCO2175B-40
U-CLRCO3286S-00
U-CLRCO2175S-01
U-CLRCO2175S-40
U-CLRCO2175S-41
U-CO2175FB-00
U-CO2175FS-00
U-CO2175FS-01
U-CO2175FW-00
To align and adjust the door:
1. Compare the top edge of the door (opposite the hinges) to the
top edge of the cabinet and note the type (up or down) of
adjustment needed.
U-2115RS-02
U-2115RSOD-00
U-2115RSOD-01
U-2115RW-00
U-2115WCOL-00
U-2115WCS-00
U-2175BEVCOL-00
U-2175BEVCOL-02
U-2175BEVCOL-60
U-2175BEVCS-00
U-2175BEVCS-02
U-2175RCB-00
U-2175RCB-02
U-2175RCGOL-00
U-2175RCGS-00
U-2175RCS-00
U-2175RCS-01
U-2175RCS-22
U-2175RCW-00
U-2175RFB-00
U-2175RFS-00
1
2
3
1
2
3
2. Remove the top hinge pivot pin with a Phillips screwdriver and
lift door off bottom hinge pin. Be careful not to lose the door
closer insert sets.
U-2175RFS-01
U-2175RFW-00
U-2175RSOD-00
U-2175RSOD-01
U-2175WCCOL-00
3. Turn the door upside down and inspect the hinge plate mounting
holes. The plate has slotted mounting holes. Loosen but do not
remove the two hinge plate screws (1).
4. If door edge opposite the hinges needs to move up, move plate
toward outside of door (2). If door edge needs to move down,
move plate toward inside of door (3). Repeat until top edge of
10
u-line.com
Download from Www.Somanuals.com. All Manuals Search And Download.
Remove Door
Reversing Black or White Doors
3
1
2
1. Hold door to keep it from falling.
2. Remove hinge screw pin (1) from top hinge using a Phillips
screwdriver.
3. Remove door by tilting forward and lifting door off bottom hinge
closer inserts.
4. Reinstall hinge screw pin (1) into top hinge using a Phillips
screwdriver.
•
•
•
The hinge hardware will be removed and reinstalled on the
opposite side of the cabinet.
Remove hole plugs.
The top hinge hardware will be reinstalled on the bottom of the
opposite side of the cabinet.
Remove plastic screw plugs (three each, top and bottom) (3)
from new hinge location. Save for reinstallation later.
The bottom hinge hardware will be reinstalled on the top of the
opposite side of the cabinet.
Remove existing top hinge.
Remove existing top hinge (three screws) (2).
4
4
Reinstall hinge to bottom opposite.
1. Install the hinge just removed from the top to the BOTTOM
opposite side of the cabinet (three screws) (2).
2. Remove the two door closer inserts (4) from the existing
bottom hinge.
3. Install door closer inserts as shown on the new bottom hinge
(4).
u-line.com
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Remove preexisting bottom hinge.
Reversing Stainless Steel Glass Doors
1. Remove the preexisting bottom hinge (three screws) (2).
Reinstall hinge to top opposite.
Remove Door
3
1. Install the hinge just removed from the bottom to the TOP
opposite side of the cabinet (three screws) (2).
1
Reinstall Hole Plugs.
1. Install plastic screw plugs (three each, top and bottom) (3) into
holes where hinge hardware was removed.
2
1. Hold door to keep it from falling.
1
2. Remove hinge screw pin (1) from top hinge using a Phillips
screwdriver.
3. Remove door by tilting forward and lifting door off bottom hinge
closer inserts.
4. Reinstall hinge screw pin (1) into top hinge using a Phillips
screwdriver.
Remove hole plugs.
1. Remove plastic screw plugs from (three each, top and bottom)
(3) from new hinge location. Save for reinstallation later.
NOTCH
5
Remove Stainless Frame
1. Remove two screws from top of door. Save screws for later
installation.
Top Of Door
Screws
Prepare door for reinstallation.
1. Remove plastic hole plug from top of door handle and reinstall
on opposite side.
2. With bottom of door facing up, remove pivot plate (5) (two
screws).
3. Flip over and install pivot plate on opposite side of door. Ensure
notch in plate faces center.
Install Door.
1. Hold door upright and tilted forward.
2. Lift door on to bottom hinge closer inserts.
3. Tilt door forward into position.
4. Hold door to keep it from falling.
2. Remove pivot plate from bottom of door by removing 2 screws.
Set pivot plate and screws aside for later installation.
5. Reinstall hinge screw pin (1) into top hinge using a Phillips
screwdriver.
Bottom Of Door
Align and adjust the door:
Align and adjust the door, see DOOR ALIGNMENT AND
ADJUSTMENT on page 10.
Pivot Plate
Screws
12
u-line.com
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Grasp outer edge of stainless frame and firmly press inside edge
of glass in while pulling stainless frame in opposite direction.
3. Swing door into frame.
4. Install screws removed in “Remove Stainless Frame” step 1 to
top of door, opposite handle.
5. Install pivot plat to bottom of door, opposite of handle, using
hardware removed in “Remove Stainless Frame” step 2. Arrange
pivot plate so the flat edge is against the edge of the door.
Pull Frame
Away
Door Edge
Pivot Plate
Flat Edge
Push Glass
In
Orient Hinge
1. Remove existing top hinge (three screws) (2).
1
4. Unhinge frame from door.
Assemble Stainless Frame
1. Prop frame against solid surface, handle side down and away
2. Insert door, logo forward, into frame at a 30° angle. For a right
hand hinge the logo should be to your right. For a left hand hinge
the logo should be to your left.
Reinstall hinge to bottom opposite.
Door Orientation Right Hand Hinge
1. Install the hinge just removed from the top to the BOTTOM
opposite side of the cabinet (three screws) (2).
2. Remove the two door closer inserts (4) from the preexisting
bottom hinge.
Logo
Door Orientation Left Hand Hinge
4
4
3. Install door closer inserts as shown on the new bottom hinge
(4).
Logo
u-line.com
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Remove existing bottom hinge.
1. Remove the existing bottom hinge (three screws) (2).
Reinstall hinge to top opposite.
1. Install the hinge just removed from the bottom to the TOP
opposite side of the cabinet (three screws) (2).
Reinstall Hole Plugs.
1. Install plastic screw plugs (three each, top and bottom) (3) into
holes where hinge hardware was removed.
Install Door.
1. Hold door upright and tilted forward.
2. Lift door on to bottom hinge closer inserts.
3. Tilt door forward into position.
4. Hold door to keep it from falling.
5. Reinstall hinge screw pin (1) into top hinge using a Phillips
screwdriver.
Align and adjust the door:
Align and adjust the door, see DOOR ALIGNMENT AND
ADJUSTMENT on page 10.
14
u-line.com
Download from Www.Somanuals.com. All Manuals Search And Download.
.
Defrosting
Cleaning
Automatic Defrost Models
Exterior Cleaning
Frost on the rear wall is normal and will melt during each off cycle.
If there is excessive build-up of 1/4" or more, manually defrost the
unit.
Vinyl Clad (Black or White) Models:
•
Clean surfaces with a mild detergent and warm water solution.
Do not use solvent-based or abrasive cleaners. Use a soft
sponge and rinse with clean water. Wipe with a soft, clean
towel to prevent water spotting.
•
•
Ensure the door is closing and sealing properly.
High ambient temperature and excessive humidity can also
produce frost.
•
Clean any glass surfaces with a non-chlorine glass cleaner.
CAUTION
!
Stainless Models:
DO NOT use an ice pick or other sharp instrument to
help speed up defrosting. These instruments can puncture
the inner lining or damage the cooling unit. DO NOT use
any type of heater to defrost. Using a heater to speed up
defrosting can cause personal injury and damage to the
inner lining.
•
Stainless door panels, handles and frames can discolor when
exposed to chlorine gas, pool chemicals, saltwater or cleaners
with bleach.
•
Keep your stainless unit looking new by cleaning with a good
quality all-in-one stainless steel cleaner polish monthly. For best
results use Claire® Stainless Steel Polish and Cleaner, which can
be purchased from U-Line Corporation (Part Number 173348).
Comparable products are acceptable. Frequent cleaning will
remove surface contamination that could lead to rust. Some
installations may require cleaning weekly.
NOTICE
The drain pan was not designed to capture the water
created when manually defrosting. To prevent water from
overflowing the drain pan, place towels or other absorbent
materials over the interior drain trough, under the
evaporator (1), before defrosting.
•
•
Do not clean with steel wool pads.
Do not use stainless steel cleaners polishes on any glass
surfaces.
•
Clean any glass surfaces with a non-chlorine glass cleaner.
To de frost:
•
Do not use cleaners not specifically intended for
stainless steel on stainless surfaces (this includes glass,
tile and counter cleaners).
1. Disconnect power to the unit.
2. For combo models remove all products from the interior.
•
If any surface discoloring or rusting appears, clean it quickly
with Bon-Ami® or Barkeepers Friend Cleanser® and a
nonabrasive cloth. Always clean towards the grain. Always finish
with Claire Stainless Steel Polish and Cleaner or comparable
product to prevent further problems.
3. Place towel or other absorbent material on bottom of ice bin.
For combo models, also place in bottom of unit.
•
Using abrasive pads such as ScotchBrite™ will cause
the graining in the stainless to become blurred.
•
Rust not cleaned up promptly can penetrate the surface of the
stainless steel and complete removal of the rust may not be
possible.
Place towels or
absorbent materials
over the interior
drain trough
Interior Cleaning
•
Disconnect power to the unit.
•
Clean the interior and all removed components using a mild
nonabrasive detergent and warm water solution applied with a
soft sponge or non-abrasive cloth.
4. Prop the door in an open position (2 in. (5cm) minimum).
5. Allow the frost to melt naturally.
•
•
Rinse the interior using a soft sponge and clean water.
Do not use any solvent-based or abrasive cleaners.
These types of cleaners may transfer taste and/or odor to the
interior products and damage or discolor the interior.
6. After the frost melts completely clean the interior and all
removed components. (See INTERIOR CLEANING)
7. When the interior is dry, reconnect power and turn unit on.
NOTE: To safeguard against contaminates in ice, discard first
three batches of ice after defrosting.
u-line.com
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Condenser Cleaning
Storage, Vacation and Moving
Interval - Every Three Months
If not using the unit for an extended period, or otherwise stored,
follow these steps completely:
To maintain operational efficiency, keep the front grille free of dust
and lint, and clean the condenser every three months. Depending
on environmental conditions, more or less frequent cleaning may
be necessary.
WARNING
!
Electrical Shock Hazard. Disconnect power before
servicing. Before operating, replace all panels. Failure
to do so may result in death or electrical shock.
WARNING
!
Disconnect electric power to the unit before cleaning
the condenser.
NOTICE
If the ambient temperature is expected to drop below
50°F, turn off and unplug unit, and drain all water from the
unit to prevent freezing damage not covered by the
warranty.
WARNING
!
DO NOT touch the condenser fins. The condenser fins
are SHARP and can be easily damaged.
1. Remove all consumable contents from the unit.
2. Disconnect the power cord from its outlet, and leave it
disconnected until the unit is returned to service.
NOTICE
DO NOT use any type of cleaner on the condenser unit.
3. Clean and dry the interior of the cabinet.
1. Remove the grill. (See MAINTENANCE)
4. During periods of nonuse, the cabinet must remain open to
prevent formation of mold and mildew. Open door a minimum
of 2 in. (5 cm) to provide the necessary ventilation.
2. Clean the condenser coil (4) using a using a soft brush with a
“combing” action or vacuum cleaner. Do not touch the
condenser coil.
3. Install the grill. (See MAINTENANCE)
Product Disposal
If the unit is being removed from service for disposal, check and
obey all Federal, State and or Local regulations regarding the
disposal and recycling of refrigeration appliances, and follow these
steps completely:
1
1. Remove all consumable contents from the unit.
2. Disconnect power to the unit and unplug the power cord from
its outlet.
2
DANGER
!
4
5
RISK OF CHILD ENTRAPMENT. Before you throw away your
old refrigerator or freezer, take off the doors and leave shelves
in place so children may not easily climb inside.
3. Remove the cabinet door.
16
u-line.com
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Guide
Service
DANGER
!
Before Calling for Service
ELECTROCUTION HAZARD. Never attempt to repair or
perform maintenance on the unit until disconnecting the
main electrical power.
If you think your U-Line product is malfunctioning, read the
OPERATION section of this guide to clearly understand the
function of the control.
Troubleshooting - What to check when problems occur:
If the problem persists, read the NORMAL OPERATING
SOUNDS and TROUBLESHOOTING GUIDE section of this guide
to help you quickly identify common problems, and possible causes
and remedies. Most often, this will resolve the problem without
the need to call for service.
Problem
Possible Cause and Remedy
Unit Does not
operate.
Electronic
No electrical supply. Plug unit in or check circuit
breaker.
display blank
If Service is Required
No Interior
light
CLRCO2175, Tighten or replace bulb, See
Maintenance) CLR2160, contact Service.
If you do not understand a troubleshooting remedy, or your
product needs service, contact U-Line Corporation directly.
Contact information appears on the rear cover of this guide.
Display showing If display shows error 10E or ER, check to make sure
error code
door is sealing correctly. Make sure to close door
completely. If sealing the door does not clear the
error, contact U-Line service for more information.
When you call, you will need your product Model and Serial
Numbers. This information can be recorded inside the front cover
of this guide. It also appears on the Model and Serial number plate
located on the upper right or rear wall of the interior of your
product.
Unit Develops
Condensation
on External
surfaces
The unit is exposed to excessive humidity, moisture
will dissipate as humidity levels decrease.
Product is
Freezing in
Adjust the temperature to a warmer set-point. (See
PRODUCT OPERATION)
Replacement Parts
Combo Models.
When you need replacement parts, always request genuine U-Line
replacements. U-Line designs and engineers products using
components that work efficiently, and provide superior service life
and performance. The use of aftermarket parts or components
may affect the safety, operation, performance or durability of your
product, and may also void its warranty.
Product is Not
Air temperature does not indicate product
Cold Enough in temperature. See PRODUCT OPERATION -
Combo Models. Checking Product Temperature.
Adjust the temperate to a cooler set-point. (See
PRODUCT OPERATION)
Ensure unit is not located in excessive ambient
temperatures or in direct sunlight.
Ensure the door is closing and sealing properly.
Ensure the interior light has not remained on too
long.
Normal Operating Sounds
Ensure nothing is blocking the front grille, found at
the bottom of the unit.
Ensure the condenser coil is clean and free of any dirt
or lint build-up.
All models incorporate rigid foam insulated cabinets to provide
high thermal efficiency and maximum sound reduction for its
internal working components. Despite this technology, your model
may make sounds that are unfamiliar.
Poor Ice quality. Unit may not be level. Check unit for levelness. (See
MAINTENANCE) Ice maker system may be dirty.
Normal operating sounds may be more noticeable because of the
unit’s environment. Hard surfaces such as cabinets, wood, vinyl or
tiled floors and paneled walls have a tendency to reflect normal
appliance operating noises.
Clean the ice maker. (See MAINTENANCE)
No Ice
Production
Ensure water is being supplied to the unit.Verify the
ice making unit is turned on (See PRODUCT
OPERATION)
Listed below are common refrigeration components with brief
description of the normal operating sounds they make. NOTE:
Your product may not contain all the components listed.
Not Enough Ice Ensure the condenser coil is clean and free of any dirt
or lint build-up.
Water in Bucket Drain may be restricted, ensure drain is free of
foreign debris.
•
Compressor: The compressor makes a hum or pulsing sound
that may be heard when it operates.
•
Evaporator: Refrigerant flowing through an evaporator may
sound like boiling liquid.
•
•
Condenser Fan: Air moving through a condenser may be heard.
Automatic Defrost Drain Pan: Water may be heard dripping or
running into the drain pan when the unit is in the defrost cycle.
•
Running Water: As your unit continues to produce ice you will
hear water flowing into the collection chambers and running
over the evaporator.
u-line.com
17
Download from Www.Somanuals.com. All Manuals Search And Download.
USE AND CARE GUIDE
®
PRODUCT INFORMATION
Complete Installation Guides, Use and Care Guides, Specifications & Features and Benefits, CAD Drawings,
Overlay Panel/Frame and Toe-Kick Specifications and Instructions, Compliance Documentation and Applicable
Energy Guides are available for reference and download at u-line.com.
SERVICE INFORMATION
Please consult your Use and Care Guide for troubleshooting information. Answers to Customer Frequently Asked
Questions are available at u-line.com under Customer Service. You may contact U-Line directly:
GENERAL INQUIRIES:
U-Line Corporation
SERVICE ASSISTANCE:
Phone 1-800-779-2547
P.O. Box 245040
FAX 1-414-354-5696
Milwaukee, Wisconsin 53224-9540 U.S.A.
Phone 1-414-354-0300
FAX 1-414-354-7905
Email: [email protected]
u-lineservice.com
Email: [email protected]
u-line.com
PARTS ASSISTANCE:
E-mail: [email protected]
BUILDING ON THREE GENERATIONS OF INNOVATION
For over five decades and through three generations, U-Line continues to be the leader in innovation, quality and
performance in the premium built-in undercounter ice making, refrigeration and wine preservation market. U-Line
has captivated those with an appreciation for the finer things with exceptional functionality, style, inspired
innovation and attention to even the smallest details. We are known and respected for our unwavering dedication
to product design, quality and selection.
In 1962, Henry Uihlein founded U-Line Corporation as an outgrowth of Ben-Hur Freezer Company and was the first
to develop and patent an automatic stand-alone undercounter residential ice maker. His foresight and determination
to develop new ideas and to succeed when there were no clear guidelines or solutions are evident today. The newest
Uihlein generation continues to build upon the family’s innovative legacy at the Milwaukee, Wisconsin based business
by providing continuity and vision from which new designs and technology continue to be born.
®
®
Today the complete U-Line product collection includes Ice Makers, Ice Machines, Wine Captain Models, Combo
Models, Refrigerator / Freezers, Refrigerators, Drawer Models and Beverage Centers. The U-Line brand offers
products in the 1000 Series, 2000 Series and the Modular 3000 Series. The 1000 Series offers a more targeted
priced product with appropriate features, while the 2000 Series offers upscale features, advanced technology and
specialized product families. Our Modular 3000 Series provides sleek design and versatile temperature settings with
®
our U-Select control. U-Line’s approach to its breadth of products, multiple price points and features allows a
choice and product that will fit any lifestyle.
DESIGNED, ENGINEERED AND ASSEMBLED IN WISCONSIN, USA
The American Built-In Undercounter Leader Since 1962
U-LINE.COM
©2013 U-Line Corporation
Publication Number 30268 4/2013 Rev.G
Download from Www.Somanuals.com. All Manuals Search And Download.
|