Owner’s Manual
Tilt Flat Screen
Wall Mount
MODEL: DWT1323S
CAUTION: DO NOT EXCEED MAXIMUM LISTED WEIGHT CAPACITY. SERIOUS INJURY OR
PROPERTY DAMAGE MAY OCCUR!
27”
75x75/100x100
40kg
MAX
(88lbs)
MAX
Русскоязычная версия настоящего руководства представлена на веб-сайте компании
Copyright © 2013 Tripp Lite. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
13-09-229-93-32A5-EN.indd
1
10/31/2013 9:59:04 AM
Component Checklist
IMPORTANT: Ensure that you have received all parts according to the component checklist prior to
DWT1323S
Package M
M4X14 (x4)
M5X14 (x4)
D5 washer (x4)
Package W
Anchor Bolt (x2)
Concrete Anchor (x2)
3
Download from Www.Somanuals.com. All Manuals Search And Download.
13-09-229-93-32A5-EN.indd
3
10/31/2013 9:59:04 AM
1.Disassemble VESA Plate
Use a screwdriver to loosen the
bottom screws in order to separate
the VESA plate from the wall mount.
2a. Mount on Wood Stud Wall
1
2
Find and mark the
exact location of
mounting holes
Anchor Bolt
3
5mm-8mm
Drill pilot holes
Tighten the screw spacing
5mm-8mm to wall plate.
Screw the wall
mount onto
the wall
WARNING
• Make sure that mounting screws are anchored into the center of the studs.
Use of a stud finder is highly recommended.
• Installers are responsible to provide hardware for other types of mounting situations.
• Installers must verify that the supporting surface will safely support the combined
load of the equipment and all attached hardware and components.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
13-09-229-93-32A5-EN.indd
4
10/31/2013 9:59:04 AM
2b. Mount on Solid Brick and Concrete Block
1
Mark the exact
location of
mounting holes
2
Concrete Anchor
Anchor Bolt
Drill pilot holes
5mm-8mm
Screw the wall
mount onto
the wall
Tighten the screw spacing
5mm-8mm to wall plate.
WARNING
• When installing wall mounts on cinder block, verify the actual concrete thickness
is at least 1-3/8” (35mm) for using the concrete anchors. Do not drill into mortar
joints! Be sure to mount in a solid part of the block, generally 1” (25mm) minimum
from the side of the block. It is suggested an electric drill on a slow setting be used
to drill the hole instead of a hammer drill to avoid breaking out the back of the hole
when entering a void or cavity.
• Installers must verify that the supporting surface will safely support the combined
load of the equipment and all attached hardware and components.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
13-09-229-93-32A5-EN.indd
5
10/31/2013 9:59:06 AM
3. Install the Wall Plate
(For claritꢀ, outer cover is not shown.)
Align top hole of wall plate to screw in
wall and lower the wall plate until the
screw is seated in upper area of tear-drop
mounting hole.
Anchor Bolt
Install the other screw and level the wall
plate, then tighten all screws securely.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
13-09-229-93-32A5-EN.indd
6
10/31/2013 9:59:09 AM
4. Install the VESA Plate
Top of display
TV
TV
TV
D5 Washer
M4X14
M5X14
or
D5 Washer
M4X14
M5X14
Screw VESA plate onto the display.
Tighten all screws but do not over tighten.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
13-09-229-93-32A5-EN.indd
7
10/31/2013 9:59:09 AM
5. Hang the display onto the Wall Plate
Wall
Hook the VESA plate (attached the display) onto the wall
plate and tighten the screw to secure it.
6. Adjustment
Wall
Wall
+10°
-15°
Push or pull from the top or bottom of display to obtain a desired angle.
Maintenance
• Check that the bracket is secure and safe to use at regular intervals(at least every three months).
13-09-229 93-32A5_RevA
8
Download from Www.Somanuals.com. All Manuals Search And Download.
13-09-229-93-32A5-EN.indd
8
10/31/2013 9:59:09 AM
|