PackagedTerminalAir
Conditioners & Heat Pumps
October 2000
PTAC-PRC001-EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Introduction
2
4
6
7
Features and Benefits
Application Considerations
Selection Procedure
Model Number Description
Performance Data
Cool and Heat Performance
Electric Power
7
8
8
15
15
16
Power Connection Wiring
Dimension and Weights
Mechanical Specifications
20
Options
Warranty
22
24
PTAC-PRC001-EN
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Features and
Benefits
Energy Efficiency
Automatic Emergency Heat
Trane PTAC units and heat pumps are
among the most efficient in the industry,
with EERs of up to 11.6 and COPs of up
to 3.3.The efficient design of the PSC
motor and airflow pattern help to reduce
the energy consumption of the fan.
Packaged terminal heat pumps tend to
be more efficient than electric heat only.
In fact, operating savings may result in a
payback of less than one year. During
heating operation, refrigerant in the heat
pump runs in the reverse direction of the
cooling operation.The outside air is
cooled, thereby giving up heat to the
refrigerant in the heat pump.
Each unit automatically switches over to
electric resistance heat if for any reason
the heat pump compressor system fails
or if the heating load is greater than the
unit capacity.
Random Restart
Avoid troublesome power surges that
can damage electrical circuits. Each unit
has a random restart circuit to prevent all
units from restarting at one time after
power disruption.
Compressor Restart Delay
Extend compressor life.The unit
automatically delays any restart attempt
by three minutes to allow the refrigerant
pressures time to equalize.
This heat is then pumped back inside,
resulting in up to three Btu’s of heat for
every Btu of energy consumed.
During cooling operation, heat is
removed from the building as the air is
cooled.This heat proceeds through the
compression cycle and is ultimately
rejected to the outside air.
Quiet Operation
State-of-the-art design and construction
provide a quiet environment for guests
to relax. Contributing to the quiet
operation of the unit are:
•An acoustically insulated bulkhead.
•Acoustical rubber-in-shear isolators
under the compressor.
Energy-saving options available with
PTAC units include:
Front Desk Contact Point
Each unit has low voltage interface
capability with a field-supplied ON/OFF
switch.Turn off heating or cooling to
unoccupied rooms.
•An isolated fan motor.
Operating sound levels are further
dampened when the unit is in the LOW
FAN mode of operation.
Fan Mode Switch
Comfort
Select continuous fan operation or cycle
the fan ON and OFF with the compressor
or heat operation.The switch is
concealed to help prevent tampering by
unauthorized personnel.
Dehumidification and air filtration are
both factors affecting comfort. When the
air is dehumidified, occupants feel more
comfortable at higher temperatures.
Trane PTACs help maintain lower
humidity levels in rooms, without the
need for expensive add-on’s. Another
benefit is that dehumidification can help
extend the life of furniture, wall
coverings and fixtures.
Temperature Limiter
This unit-mounted mechanical control
allows guests to adjust in-room
temperature settings within a pre-
programmed range.
When ventilation air is filtered, rooms
stay cleaner, longer.The hidden
ventilation air intake filters outside air to
reduce dust and pollen.
Reliability
These features help assure reliable
operation:
User-Friendly Controls
Freeze Protection
Controls are easy to read, understand
and activate.
When the unit senses temperatures of
40°F or below, the unit activates the fan
motor and either the electric resistance
heater or the hydronic heater to help
prevent pipes or fixtures from freezing.
This also overrides front desk control of
the unit mounted or wall sensor.
4
PTAC-PRC001-EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Features and
Benefits
Remote Thermostat Control
Special Paint Protection
The electrodeposition paint system on
the exterior panels assure the unit and
wall sleeve will withstand years of
moisture and atmospheric pollutants
without giving up its looks to rust and
corrosion.
Each unit is built to be operated from a
remote-mounted thermostat, if desired.
Even if it is started without a remote, a
built-in low voltage power source can
accommodate a large variety of
thermostat choices — manual, auto
changeover or programmable — at a
later date.
Ease of Installation and Servicing
After the sleeve is in place, plug in or
directly hard-wire the unit and it is ready
to run.This unit has been designed to
replace most competitors’ units. In fact
this unit can fit into most existing
sleeves, making replacement of old or
inefficient units easy and economical.
And of course, the units may be installed
flush with the outside wall.
The main components are easily
serviced; the unit is easy to diagnose or
troubleshoot to spot potential problems.
Remote Temperature Sensing
Occupants enjoy ultimate comfort with
consistent climate control. Attach an
optional, inexpensive remote thermistor
temperature sensing device and
temperatures are held more closely to
the chosen room setting.
Attractive and Compact Design
When the filter needs to be cleaned or
replaced, the filter access door tilts
forward for easy access. For more
extensive service, the unit slides out of
the sleeve easily for full access to all
working components.
The unit front has a sleek seven-inch
depth, one of the shallowest silhouettes
in the industry today.To inhibit
tampering, the front can be secured to
the chassis with hidden screws.
Our unit’s new stylish design and neutral
color make it compatible with virtually
any room decor or architectural design. It
blends into the room’s color scheme.
PTAC-PRC001-EN
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Application
Considerations
Curtain Wall Installation
Block and BrickVeneer Installation
Frame and BrickVeneer Installation
PanelWall Installation
PanelWall and BlockVeneer Installation
Optional Leveling Leg
On applications not requiring subbase or leveling legs, unit may be flush mounted to floor.
Sleeve Installation Data
Framing forWall Case
Framing With Lintel
Attaching Wall Sleeve to Opening
1. 3¼” m inim um with subbase.
2. On applications not requiring subbase or
leveling legs, unit m ay be flush m ounted to floor.
6
PTAC-PRC001-EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Model
Num ber
Description
MODEL NOMENCLATURE
PT E C 090 1 G * A
Digit 8 — Main Power Supply
Digits 1,2 — Packaged Terminal
Air Conditioner
1 = 208-230/60/1
2 = 265/60/1
Digit 3 — Product Type
Digit 9 — Electric Heating Capacity**
E = Air Conditioner
H = Heat Pump
0 = No Electric Heat – Air Conditioners Only
E = 2.5 kW
G = 3.5 kW (208-230V)
G = 3.7 kW (265V)
Digit 4 — Development Sequence
C =Third Development
J
= 5.0 kW*
Digits 5,6,7 — Unit Cooling Capacity
Digit 10 — Design Sequence
Digit 11— Miscellaneous
070 = 7,000 Btu
090 = 9,000 Btu
120 = 12,000 Btu
150 = 15,000 Btu
A = Standard
B = Power Vent
C = Corrosion Resistant
D = Condensate Pump
H = Hydronic Chassis
F = Hydronic with Power Vent and Door
G = Hydronic with Power Door
J = Power Door
K = Condensate Pump with Power Vent
L = Condensate Pump with Power Door
Notes:
1. Corrosion resistant, condensate pum p, power vent units and all special units require extended ship cycles.
2. Only the following units are available from stock and can norm ally ship within 3 days after release.
3. Contact your local Trane representative for current stock availability and inform ation on m inim um quantity
requirem ents and shipping schedule for special production units.
Stock Style Models
PTEC0701GCA
PTEC0901GCA
PTEC1201GCA
PTHC1501GCA
PTHC1501JCA
PTEC0902GCA
PTHC0902GCA
PTEC1202GCA
PTHC1202GCA
PTEC1502GCA
PTHC1502GCA
PTEC1501GCA
PTEC1501JCA
PTHC0701GCA
PTHC0901GCA
PTHC1201GCA
*Sizes 09, 12 and 15 only.
**All heat pum p units m ust have electric coils.
PTAC-PRC001-EN
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Perform ance
Data
Table PD-1 — Cooling Performance — Air Conditioner with Electric Heat Models
ModelType
Air Conditioner
Model No.1 & 5
Voltage3
PTEC 07
230
7100
2.8
PTEC 09
230
9100
3.7
PTEC 12
230
12000
5.0
PTEC 15
230
14200
6.9
208
7000
3.0
265
7100
2.3
208
8900
3.8
265
9100
3.0
208
11900
5.0
265
12000
4.3
208
14000
6.9
265
14200
5.9
Capacity (Btu)6
Amps
Watts
EER
600
11.6
610
11.6
610
11.6
785
11.3
805
11.3
805
11.3
1110
10.7
1110
10.7
1130
10.7
1520
9.2
1545
9.2
1525
9.3
Unit without Electric Heater
Min. Circuit/Ampacity 2 & 4
cfm (cool, wet coil)
4.0
4.0
3.6
5.1
5.1
4.4
6.4
6.4
6.4
8.4
8.4
7.4
High
240
205
245
220
245
220
240
205
245
220
245
220
325
250
315
220
325
250
315
220
325
250
325
250
Low
cfm (dry coil)
High
260
215
65*
265
230
65*
265
230
65*
260
215
65*
265
230
65*
265
230
65*
345
265
70*
335
235
70*
345
265
70*
335
235
70*
345
265
70*
345
265
70*
Low
Ventilated Air, cfm (fan only)
Dehumidification (pints/hr.)
Net wt. (approximate lbs.)
Shipping wt. (approximate lbs.)
1.6
90
105
1.6
90
105
1.6
90
105
2.6
95
110
2.6
95
110
2.6
95
110
3.5
105
120
3.5
105
120
3.5
105
120
4.4
110
125
4.4
110
125
4.4
110
125
* 95 cfm with optional power vent kit. Actual vent cfm performance will vary due to application and installation conditions.
Table PD-2 — Cooling Performance —Heat Pump with Electric Heat Models
ModelType
Heat Pumps
Model No.1 & 5
Voltage3
PTHC 07
230
7100
2.8
PTHC 09
230
9000
3.5
PTHC 12
230
12000
4.6
PTHC 15
230
14000
6.3
208
7000
3.0
265
7100
2.3
208
8800
3.8
265
9000
3.0
208
11800
5.0
265
12000
4.3
208
13800
6.9
265
14000
5.9
Capacity(Btu)6
Amps
Watts
EER
610
11.5
615
11.5
615
11.5
785
11.2
805
11.2
805
11.2
1110
10.7
1120
10.7
1120
10.7
1485
9.3
1505
9.3
1505
9.3
Unit without Electric Heater
Min Circuit/Ampacity 2 & 4
cfm (cool, wet coil)
4.0
4.0
3.6
5.1
5.1
4.4
7.3
7.3
5.7
8.4
8.4
7.4
High
240
205
245
220
245
220
240
205
245
220
245
220
315
220
325
250
325
250
315
220
325
250
325
250
Low
cfm (dry coil)
High
260
215
65*
265
230
65*
265
230
65*
260
215
65*
265
230
65*
265
230
65*
335
235
70*
345
265
70*
345
265
70*
335
235
70*
345
265
70*
345
265
70*
Low
Ventilated Air, cfm (fan only)
Dehumidification (pints/hr.)
Net wt. (approximate lbs.)
Shipping wt. (approximate lbs.)
1.6
95
110
1.6
95
110
1.6
95
110
2.6
100
115
2.6
100
115
2.6
100
115
3.5
110
125
3.5
110
125
3.5
110
125
4.4
115
130
4.4
115
130
4.4
115
130
*95 cfm with optional power vent kit. Actual vent cfm performance will vary due to application and installation conditions.
Notes:
1. All 265 volt m odels m ust use Trane’s subbase or Trane’s hard-wire junction box kit.
2. Minim um branch circuit am pacity ratings conform to the National Electric Code. However, local codes should apply.
3. Minim um voltage on 208/230 volt m odels is 197 volts; m axim um is 253 volts. Minim um voltage on 265 volt m odels is 238.5 volts; m axim um is 291.5 volts.
4. Overcurrent protection for all u n it s w it h o u t e le c t ric h e a t e rs is 1 5 a m p s . Overcurrent protection on 265 volt m odels m ust be cartridge-style tim e delay fuses (included and
factory installed on Trane chassis). Note: All heat pum p units m ust have electric coils.
5. Minim um operating am bient = 45°F.
6. Certified in accordance with the Unitary Air-Conditioner Equipm ent certification program , which is based on ARI standard 310/380.
EER — Energy Efficiency Ratio per Am erican Refrigeration Institute (ARI) Test Procedures.
COP — Coefficient of Perform ance per ARI Test Procedures.
8
PTAC-PRC001-EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Perform ance
Data
Table PD-3 — Heat Pump Reverse Cycle Heating Capacity (Btu)
Model No.1
Voltage3
Amps
PTHC 07
230
2.6
PTHC 09
230
3.2
PTHC 12
230
4.5
PTHC 15
230
5.7
208
3.0
265
2.2
208
3.6
265
2.6
208
5.1
265
3.9
208
6.3
265
5.4
Watts
550
6200
3.3
570
6400
3.3
570
6400
3.3
730
8000
3.2
740
8100
3.2
740
8100
3.2
1000
10600
3.1
1020
10800
3.1
1020
10800
3.1
1380
13500
2.8
1390
13300
2.8
1390
13300
2.8
Btu2
COP2
cfm (dry)
Heating2 Btu °F
Outdoor Ambient
230
235
235
230
235
235
290
310
310
335
345
345
62
57
52
47
8200
7600
6900
6200
8400
7800
7100
6400
3.3
5700
5100
4500
745
690
630
570
505
8400
7800
7100
6400
3.3
5700
5100
4500
745
690
630
570
505
10200
9600
8900
8000
3.2
7200
6400
5600
935
880
815
730
660
10300
9700
9000
8100
3.2
7300
6500
5700
940
890
825
740
670
10300
9700
9000
8100
3.2
7300
6500
5700
940
890
825
740
670
13000
12200
11400
10600
3.1
9800
9000
8200
1230
1150
1075
1000
925
13200
12400
11600
10800
3.1
10000
9200
8400
1245
1170
1095
1020
945
13200
12400
11600
10800
3.1
10000
9200
8400
1245
1170
1095
1020
945
16300
15300
14200
13200
2.8
12200
11200
10100
1705
1600
1485
1380
1275
1170
16400
15400
14300
13300
2.8
12300
11300
10200
1715
1610
16400
15400
14300
13300
2.8
12300
11300
10200
1715
1610
Rating Point
2
(COP) 3.3
42
37
32
62
57
52
47
42
37
32
5500
4900
4300
730
675
610
550
490
435
380
Watts
Outdoor Ambient
1495
1390
1285
1180
1495
1390
1285
1180
450
400
450
400
585
510
595
520
595
520
850
775
870
795
870
795
1055
1065
1065
Notes:
1. All 265 volt m odels m ust use Trane’s subbase or Trane’s hard-wire junction box kit.
2. Heating capacity and efficiency is based on unit operation without condensate pum p. Unit autom atically switches to electric heat at 25°F outdoor coil tem perature.
Depending upon relative hum idity conditions, this will occur at approxim ately 35 degrees outdoor am bient tem perature.
PTAC-PRC001-EN
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Perform ance
Data
Table PD-4 — PTECAir Conditioner — 208V
WBT Ent DBT Ent
OutdoorTemperature (°F)
Nominal Indoor
Indoor
85
95
105
115
Unit
Size
Coil
(°F)
Coil
(°F)
Total
Btu
Sen
Btu
%
SH
Total
Btu
Sen
Btu
%
SH
Total
Btu
Sen
Btu
%
SH
Total
Btu
Sen
Btu
%
SH
75
80
85
75
80
85
75
80
85
75
80
85
75
80
85
75
80
85
75
80
85
75
80
85
75
80
85
75
80
85
75
80
85
75
80
85
6680
6930
7205
7440
7345
7390
8335
8245
8150
8385
8335
8480
9510
9410
9255
10710
10585
10450
11265
11220
11505
12770
12630
12425
14435
14260
14070
13245
13140
13465
15035
14845
14575
16875
16780
16535
5695
6930
7205
4005
5385
6570
2835
3980
5285
6285
7390
8480
5010
6240
7295
3705
4790
5875
8715
10210
11505
6910
8330
9815
5060
6520
7985
10205
11930
13465
8120
9745
11455
5915
7655
9330
85
100
100
54
73
89
34
48
65
75
89
100
53
66
79
35
45
56
77
91
100
54
66
79
35
46
57
77
91
100
54
66
79
35
46
56
6380
6665
7030
7155
*7000
7105
7885
7875
7750
7940
7905
8130
9075
*8900
8825
10135
10020
9880
10610
10575
10965
12205
*11900
11805
13645
13460
13290
12490
12345
12775
14365
*14000
13785
16120
15870
15595
5545
6665
7030
4140
5250
6445
2800
3850
4995
6065
7165
8130
4810
5820
7165
3490
4580
5665
8410
9890
10965
6670
8025
9560
4765
6230
7700
9830
11515
12775
7835
9375
11125
5625
7315
8970
87
100
100
58
75
91
36
49
64
76
6030
6270
6745
6680
6660
6690
7485
7415
7345
7460
5665
6270
6745
4150
5295
6270
2665
3845
4845
5830
6930
7765
4610
5610
6890
3280
4365
5445
8070
9525
10300
6305
7705
9215
4470
5930
7400
9405
11045
11965
7345
8975
10680
5260
6905
8610
94
100
100
62
80
94
36
52
66
78
93
100
54
67
84
34
46
59
82
97
100
56
69
85
35
47
60
81
97
100
55
69
84
35
47
59
5710
5980
6320
6290
6270
6330
7070
7010
6940
6960
7050
7345
7900
7795
7680
5530
5980
6320
4000
5175
6330
2520
3710
4705
5600
7050
7345
4510
5335
6470
3060
4145
5230
7675
9110
9605
5950
7370
8875
4145
5575
7020
8940
10760
11325
6875
8575
10370
4790
6445
8225
97
100
100
64
83
100
36
53
68
80
100
100
57
68
84
34
47
61
85
100
100
57
72
89
35
48
62
84
100
100
56
72
88
34
47
61
61
67
73
61
67
73
61
67
73
61
67
73
07
09
12
15
91
100
53
65
81
34
46
57
79
94
100
55
67
81
35
46
58
79
93
100
55
67
81
35
46
58
7435
7765
8465
8355
8210
9555
9420
9270
9875
9815
10300
11320
11115
10905
12840
12640
12370
11570
11395
11965
13280
13020
12670
15130
14835
14530
8935
8795
8640
9000
9110
9605
10440
10200
9980
11925
11630
11350
10610
10760
11325
12200
11990
11790
14010
13635
13385
*These capacities are based on ARI rating point 80/67 entering air tem perature, 95°F outdoor am bient.
10
PTAC-PRC001-EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Perform ance
Data
Table PD-5 — PTEC Air Conditioner — 230/265V
WBT Ent DBT Ent
OutdoorTemperature (°F)
Nominal Indoor
Indoor
85
95
105
115
Unit
Size
Coil
(°F)
Coil
(°F)
Total
Btu
Sen
Btu
%
SH
Total
Btu
Sen
Btu
%
SH
Total
Btu
Sen
Btu
%
SH
Total
Btu
Sen
Btu
%
SH
75
80
85
75
80
85
75
80
85
75
80
85
75
80
85
75
80
85
75
80
85
75
80
85
75
80
85
75
80
85
75
80
85
75
80
85
6780
7030
7305
7540
7445
7490
8435
8345
8250
8585
8535
8680
9710
9610
9455
10910
10785
10650
11365
11320
11605
12870
12730
12525
14535
14360
14170
13445
13340
13665
15235
15045
14775
17075
16980
16735
5795
7030
7305
4105
5485
6670
2935
4080
5385
6485
7590
8680
5210
6440
7495
3905
4990
6075
8815
10310
11605
7010
8430
9915
5160
6620
8085
10405
12130
13665
8320
9945
11655
6115
85
100
100
54
74
89
35
49
65
76
6480
6765
7130
7255
*7100
7205
7985
7975
7850
8140
8105
8330
9275
*9100
9025
10335
10220
10080
10710
10675
11065
12305
*12000
11905
13745
13560
13390
12690
12545
12975
14565
*14200
13985
16320
16070
15795
5645
6765
7130
4240
5350
6545
2900
3950
5095
6265
7365
8330
5010
6020
7365
3690
4780
5865
8510
9990
11065
6770
8125
9660
4865
6330
7800
10030
11715
12975
8035
9575
11325
5825
7515
9170
87
100
100
58
75
91
36
50
65
77
91
100
54
66
82
36
47
58
79
94
100
55
68
81
35
47
58
79
93
100
55
67
81
36
47
58
6130
6370
6845
6780
6760
6790
7585
7515
7445
7660
7635
7965
8665
8555
8410
9755
9620
9470
5765
6370
6845
4250
5395
6370
2765
3945
4945
6030
7130
7965
4810
5810
7090
3480
4565
5645
8170
9625
10400
6405
7805
9315
4570
6030
7500
9605
11245
12165
7545
9175
10880
5460
7105
8810
94
100
100
63
80
94
36
52
66
79
93
100
56
68
84
36
47
60
82
97
100
56
70
85
35
47
60
82
97
100
56
69
85
36
47
60
5810
6080
6420
6390
6370
6430
7170
7110
7040
7160
7250
7545
8100
7995
7880
9135
8995
8840
9100
5630
6080
6420
4100
5275
6430
2620
3810
4805
5800
7250
7545
4710
5535
6670
3260
4345
5430
7775
9210
9705
6050
7470
8975
4245
5675
7120
9140
10960
11525
7075
8775
10570
4990
6645
8425
97
100
100
64
83
100
37
54
68
81
100
100
58
69
85
36
48
61
85
100
100
57
73
89
35
48
62
85
100
100
57
72
88
35
48
62
61
67
73
61
67
73
61
67
73
61
67
73
07
09
12
15
89
100
54
67
79
36
46
57
78
91
100
54
66
79
36
46
57
77
91
100
55
66
79
36
46
57
9975
9915
9210
10400
11420
11215
11005
12940
12740
12470
11770
11595
12165
13480
13220
12870
15330
15035
14730
9705
10540
10300
10080
12025
11730
11450
10810
10960
11525
12400
12190
11990
14210
13835
13585
7855
9530
*These capacities are based on ARI rating point 80/67 entering air tem perature, 95°F outdoor am bient.
PTAC-PRC001-EN
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Perform ance
Data
Table PD-6 — PTHC Heat Pump — 208V
WBT Ent DBT Ent
OutdoorTemperature (°F)
Nominal Indoor
Indoor
85
95
105
115
Unit
Size
Coil
(°F)
Coil
(°F)
Total
Btu
Sen
Btu
%
SH
Total
Btu
Sen
Btu
%
SH
Total
Btu
Sen
Btu
%
SH
Total
Btu
Sen
Btu
%
SH
75
80
85
75
80
85
75
80
85
75
80
85
75
80
85
75
80
85
75
80
85
75
80
85
75
80
85
75
80
85
75
80
85
75
80
85
6680
6930
7205
7440
7345
7390
8335
8245
8150
8290
8225
8285
9420
9305
9145
10610
10480
10345
11165
11120
11405
12670
12530
12325
14335
14160
13970
13055
12955
13275
14820
14635
14370
16635
16540
16300
5695
6930
7205
4005
5385
6570
2835
3980
5285
6120
7175
8285
4905
5890
7085
3675
4705
5730
8615
10110
11405
6810
8230
9715
4960
6420
7885
10055
11755
13275
8000
9605
11290
5825
7545
9195
85
100
100
54
73
89
34
48
65
74
6380
6665
7030
7155
*7000
7105
7885
7875
7750
7840
7785
7920
8960
*8800
8710
10050
9920
9775
10510
10475
10865
12105
*11800
11705
13545
13360
13190
12310
12170
12590
14160
*13800
13585
15890
15645
15370
5545
6665
7030
4140
5250
6445
2800
3850
4995
5900
6945
7920
4775
5660
6945
3465
4495
5520
8310
9790
10865
6570
7925
9460
4665
6130
7600
9690
11350
12590
7720
9240
10970
5540
7210
8845
87
100
100
58
75
91
36
49
64
75
89
100
53
64
80
34
45
56
79
93
100
54
67
81
34
46
58
79
93
100
55
67
81
35
46
58
6030
6270
6745
6680
6660
6690
7485
7415
7345
7350
7315
7525
8360
8250
8095
9450
9315
5665
6270
6745
4150
5295
6270
2665
3845
4845
5660
6705
7525
4500
5485
6670
3245
4275
5300
7970
9425
10200
6205
7605
9115
4370
5830
7300
9270
10885
11795
7240
8845
10530
5185
6805
8490
94
100
100
62
80
94
36
52
66
77
92
100
54
66
82
34
46
58
82
97
100
55
69
84
34
46
59
81
97
100
55
69
84
35
47
59
5710
5980
6320
6290
6270
6330
7070
7010
6940
6855
6810
7105
7785
7675
7520
8835
8690
8535
8900
9010
9505
10340
10100
9880
11825
11530
11250
10460
10605
11165
12025
11820
11620
13810
13440
13195
5530
5980
6320
4000
5175
6330
2520
3710
4705
5420
6790
7105
4400
5170
6400
3020
4050
5075
7575
9010
9505
5850
7270
8775
4045
5475
6920
8815
10605
11165
6775
8450
10220
4720
6355
8105
97
100
100
64
83
100
36
53
68
79
100
100
57
67
85
34
47
59
85
100
100
57
72
89
34
47
62
84
100
100
56
71
88
34
47
61
61
67
73
61
67
73
61
67
73
61
67
73
07
09
12
15
87
100
52
63
77
35
45
55
77
91
100
54
66
79
35
45
56
77
91
100
54
66
79
35
46
56
9165
9775
9715
10200
11220
11015
10805
12740
12540
12270
11405
11230
11795
13090
12830
12485
14915
14625
14320
*These capacities are based on ARI rating point 80/67 entering air tem perature, 95°F outdoor am bient.
12
PTAC-PRC001-EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Perform ance
Data
Table PD-7 — PTHC Heat Pump — 230/265V
WBT Ent DBT Ent
OutdoorTemperature (°F)
Nominal Indoor
Indoor
85
95
105
115
Unit
Size
Coil
(°F)
Coil
(°F)
Total
Btu
Sen
Btu
%
SH
Total
Btu
Sen
Btu
%
SH
Total
Btu
Sen
Btu
%
SH
Total
Btu
Sen
Btu
%
SH
75
80
85
75
80
85
75
80
85
75
80
85
75
80
85
75
80
85
75
80
85
75
80
85
75
80
85
75
80
85
75
80
85
75
80
85
6780
7030
7305
7540
7445
7490
8435
8345
8250
8490
8425
8485
9620
9505
9345
10810
10680
10545
11365
11320
11605
12870
12730
12525
14535
14360
14170
13255
13155
13475
15020
14835
14570
16835
16740
16500
5795
7030 100
7305 100
85
6480
6765
7130
7255
*7100
7205
7985
7975
7850
8040
7985
8120
9160
*9000
8910
10250
10120
9975
10710
10675
11065
12305
*12000
11905
13745
13560
13390
12510
12370
12790
14360
*14000
13785
16090
15845
15570
5645
6765
7130
4240
5350
6545
2900
3950
5095
6100
7145
8120
4975
5860
7145
3665
4695
5720
8510
9990
11065
6770
8125
9660
4865
6330
7800
9890
11550
12790
7920
9440
11170
5740
7410
9045
87
100
100
58
75
91
36
50
65
76
6130
6370
6845
6780
6760
6790
7585
7515
5765
6370
6845
4250
5395
6370
2765
3945
4945
5860
6905
7725
4700
5685
6870
3445
4475
5500
8170
9625
10400
6405
7805
9315
4570
6030
7500
9470
11085
11995
7440
9045
10730
5385
7005
8690
94
100
100
63
80
94
36
52
66
78
92
100
55
67
83
36
47
59
82
97
100
56
70
85
35
47
60
82
97
100
56
69
85
36
47
60
5810
6080
6420
6390
6370
6430
7170
7110
5630
6080
6420
4100
5275
6430
2620
3810
4805
5620
6990
7305
4600
5370
6600
3220
4250
5275
7775
9210
9705
6050
7470
8975
4245
5675
7120
9015
10805
11365
6975
8650
10420
4920
6555
8305
97
100
100
64
83
100
37
54
68
80
100
100
58
68
85
36
48
60
85
100
100
57
73
89
35
48
62
85
100
100
57
72
88
35
48
62
61
67
73
61
67
73
61
67
73
61
67
73
4105
5485
6670
2935
4080
5385
6320
7375
54
74
89
35
49
65
74
88
07
09
12
15
7445
7550
7515
7040
7055
7010
89
100
54
65
80
36
46
57
79
94
100
55
68
81
35
47
58
79
93
100
55
67
81
36
47
58
8485 100
7725
8560
8450
8295
9650
9515
9365
9975
9915
10400
11420
11215
11005
12940
12740
12470
11605
11430
11995
13290
13030
12685
15115
14825
14520
7305
7985
7875
7720
9035
8890
8735
9100
9210
9705
10540
10300
10080
12025
11730
11450
10660
10805
11365
12225
12020
11820
14010
13640
13395
5105
6090
7285
3875
4905
5930
8815
10310
53
64
78
36
46
56
78
91
11605 100
7010
8430
9915
5160
6620
8085
10255
11955
54
66
79
36
46
57
77
91
13475 100
8200
9805
11490
6025
7745
9395
55
66
79
36
46
57
*These capacities are based on ARI rating point 80/67 entering air tem perature, 95°F outdoor am bient.
PTAC-PRC001-EN
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Perform ance
Data
Table PD-8 — Heating Capacity —Water
Heating Capacity (Btu) Hot Water
Pressure
7000 & 9000 Btu Units
12000 Btu Units
15000 Btu Units
Drop
(psig)
200°F EWT
Fan Speed
180°F EWT
Fan Speed
200°F EWT
Fan Speed
180°F EWT
Fan Speed
200°F EWT
Fan Speed
Hi
180°F EWT
Fan Speed
2-Way
gpm
1.00
1.13
1.25
1.38
1.50
1.63
1.75
1.88
2.00
2.13
2.25
2.38
2.50
2.63
2.75
Coil
0.93
1.03
1.14
1.26
1.40
1.55
1.71
1.89
2.10
2.32
2.57
2.84
3.14
3.48
3.85
Valve
0.19
0.24
0.30
0.36
0.43
0.50
0.58
0.66
0.76
0.85
0.96
1.07
1.18
1.30
1.43
Hi
Lo
Hi
Lo
Hi
Lo
Hi
Lo
Lo
Hi
Lo
14910
15216
15500
15762
16003
*16222
16420
16596
16751
16884
16995
17085
17154
17201
17226
13388
13706
13997
14262
14501
14714
14900
15061
15195
15302
15384
15439
15467
15470
15505
12639
12898
13139
13361
13565
13751
13919
14068
14199
14312
14407
14483
14541
14581
14603
11186
11452
11696
11917
12117
12295
12450
12584
12696
12786
12854
12900
12924
12926
12956
16945
17360
17745
18099
18423
18717
18980
19212
*19268
19586
19727
19838
19919
19968
19988
14387
14689
14968
15222
15454
15661
15845
16006
16142
16255
16345
16410
16452
16471
16580
14257
14607
14930
15228
15501
15748
15969
16165
16212
16479
16598
16691
16759
16801
16817
12152
12407
12642
12858
13053
13228
13384
13519
13635
13730
13806
13861
13897
13912
14004
17858
18276
18666
19025
19356
19658
19930
20173
20387
*20445
20727
20853
20950
21018
21056
15534
15955
16338
16684
16991
17261
17494
17689
17846
17965
18047
18091
18097
18065
18140
15049
15401
15729
16032
16311
16565
16794
16999
17179
17229
17466
17572
17654
17711
17744
13312
13672
14001
14297
14561
14792
14991
15158
15293
15395
15465
15503
15508
15481
15545
*Based on ARI Rating Conditions of 70°F Entering Air Tem p., 200°F Entering Water Tem p and 180°F Leaving Water Tem p.
Max Water Tem perature 200°F Max. Water Pressure - 200 psig.
Table PD-9 — Heating Capacity — Steam
7,000 & 9,000 Btu Units
12,000 Btu Units
Fan Speed
15,000 Btu Units
Fan Speed
Steam
PSIG
2
Fan Speed
High
20,236
Low
17,816
High
21,694
Low
18,306
High
23,709
Low
—
3
4
20,686
20,821
18,253
18,544
22,100
22,822
19,003
19,313
25,676
26,325
21,099
23,678
14
PTAC-PRC001-EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Electric
Power
Table EP-1 — Electric Heat Capacity and Electrical Data (For PTEC and PTHC Models)***
Electric
Nominal Heating
Minimum Circuit Overcurrent
Heater
Size (kW)
2.0/2.5
2.9/3.5
4.1/5.0
2.5
No. Of
Stages
1
1
**
1
Total
Watts4
2,140/2,650
3,040/3,650
4,240/5,150
2,650
Total
Amps
10.2/11.5
14.5/15.8
20.3/22.3
10
Power
Cord
2
Voltage
208/230
208/230
208/230
265
265
265
Notes:
Btu 208
6,800
9,900
14,000
—
Btu 230
8,500
12,000
17,100
—
Btu 265
—
—
Ampacity1
14.2
19.6
27.7
12.4
Protection3
15
20
30
15
20
25
6-15 P
6-20 P
6-30 P
7-20 P
7-20 P
7-30 P
—
8,500
12,600
17,100
3.7
5.0
1
**
—
—
—
—
3,850
5,150
14.6
19.5
18.1
24.2
1. Minim um branch circuit am pacity ratings conform to the National Electric Code. However, local codes should apply.
2. Minim um voltage on 208/230 volt m odels is 197 volts; m axim um is 253 volts. Minim um voltage on 265 volt m odels is 238.5 volts; m axim um is 291.5 volts.
3. Overcurrent protection for all u n it s w it h o u t e le c t ric h e a t e rs is 1 5 a m p s . Overcurrent protection on 265 volt m odels m ust be cartridge-style tim e delay fuses (included and
factory installed on Trane chassis).
4. Total watts for 7,000 and 9,000 Btu m odels; add 40 watts for size 12 and 70 watts for size 15.
**PTHC07, 09 and 12 are two-stage; PTHC15 is one-stage.
*** Note: All heat pum ps m ust have electric coils.
Table EP-2 — Power Receptacle Configurations
Voltage
208/230
265
Unit Supplied Plug
Amps
15
20
30
20
30
NEMA Rating
6-15P
6-20P
6-30P
7-20P
7-30P
Receptacle
Amps
20
20
30
20
30
NEMA Rating
Notes:
6-20R
6-20R
6-30R
7-20R
7-30R
1. All wiring, including receptacles, m ust be m ade in accordance with local electrical codes and regulations.
2. NEMA 6-15 and 6-20 plugs fit in NEMA 6-20 receptacles.
3. Receptacles shown for 208/230 applications are factory supplied with subbase, per local codes for wall m ounted receptacles use or the corresponding NEMA receptacles.
4. Receptacles shown for 265 volt applications are factory supplied with subbase. Codes do not allow 265 volt units to m ate with wall m ounted receptacles. They m ay however be
hard-wired per Local Codes.
PTAC-PRC001-EN
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Dim ension and
Weights
Unit with Wall Sleeve and Subbase Accessory
Top View
Front View
Right Side View
Notes:
1. Allow a m inim um of 31/4” clearance between cabinet and floor to perm it installation of options subbase.
2. Allow m inim um of 3” clearance between cabinet and side walls to perm it front panel rem oval.
3. Drain tube can be m ounted either right side, left side or bottom of sleeve. Bottom drain to be located by custom er. Drain kit shipped separate.
4. Unit provides 20 percent outside air.
5. Detachable cord ships attached to unit. Cord can be rem oved for direct attachm ent of building wiring or wiring from junction box kit.
6. For U.S. approval — 265 volt units and units with duct packages m ust have perm anent wiring connection. Perm anent wiring requirem ent can be m et either by supplying
afull length subbase for concealed cord connection or by direct wiring with junction box kit.
7. Control door provided on standard unit for access to controls.
16
PTAC-PRC001-EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Dim ension and
Weights
Field Supplied Extension
PTAC-PRC001-EN
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Dim ension and
Weights
Hydronic Heat Kit
NOTE:Wall sleeve must
extend exactly 3 inches
from finished interior
wall
Notes:
1. This kit com pletely encloses al
2. The chassis can slide out for ea
3. The kits feature left or right-ha
4. Unit retains com plete service a
18
PTAC-PRC001-EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Dim ension and
Weights
Duct Package
When two adjacent rooms need to be conditioned, a main duct kit and a duct extension kit are possible options.These kits transfer
air from one room to another, yet allow different air flows for the rooms (airflow distribution can be adjusted from
65/45 to 80/20.)
Front View
Duct Termination Kit
The Duct Termination Kit
includes a grille and a
sleeve for fitting duct or
duct extension through
the wall.
PTAC-PRC001-EN
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Mechanical
Specifications
Unit Chassis
Condenser/Evaporator Fans
Outside Air Damper/Vent Control
Each unit will be slide-out design shipped
with room cabinet front installed. Unit
chassis will have the ability to be installed
with zero reversing clearance from
finished floor. An electrical power cord
will be included with chassis and
installed by the manufacturer to assure
proper NEMA 6 or 7 configuration and
UL approved length. Unit will be tested
for conformance to ASTME water
One direct drive with a permanent split
capacitor two-speed motor.The
condenser fan will be propeller type and
the indoor evaporator fan will be a
centrifugal blower type.
The vent control will allow 65 to 70 cfm
of fresh air to be drawn into the room.
This fresh air can provide ventilation
when the blower is operating.To obtain
access to the vent control, remove the
cabinet front.The vent control lever is on
the left side of the chassis.The control
lever must be rotated to either open or
close the damper. Actual vent cfm
Cooling Condensate Removal
High humidity conditions may call for
condensate removal system.The
outdoor fan diffuses water directly on to
the outdoor condenser coil for rapid
evaporation and increased cooling
efficiency.
performance will vary due to application
and installation conditions.
infiltration specification ASTME 331-86
which assures no water infiltration when
tested at eight inches of rain per hour at
63 mph wind for 15 minutes.
Filtered Outdoor Air Intake
The outdoor air intake will be filtered
with a talc-filled polypropylene filter that
will reduce dust from coming into the
room.
Compressor
Room Cabinet/Front Panel
The compressor will be hermetically
sealed, internally isolated, rotary-type
and permanently mounted on rubber
isolators. No removal or adjustment of
compressor hold down bolts will be
required during installation.
The room cabinet/front panel will have
sloped discharge so that obstructions are
not placed on unit.The discharge
conditioned air can be directed into the
room at an angle of 15 to 40 degrees
from the vertical position.The discharge
grille will be a polycarbonate material to
resist bending, cracking, rusting and
corrosion.The front panel will be able to
be field secured to chassis to inhibit
tampering. Cabinet depth will be seven-
inch to minimize unit’s impact on room
space.
Paint System Corrosion Protection
All units are built with hot-dipped
galvanized steel. Metal parts are then run
through a six-stage zinc phosphate
cleaner/pretreatment, painted with a
cathodic electroplating of an epoxy resin
paint and baked for 20 minutes at 350°F.
All exterior parts that are exposed to
sunlight get an additional coating of
polyester and are baked for 20 minutes
at 350°F for additional protection from
the fading effects of ultraviolet rays.This
paint process makes the unit highly
resistant to normal rust, corrosion and
fading. It is the best paint process in the
industry today.
Coils
Coils will have rifled copper tubing
expanded into rippled-edge louvered
aluminum fins.
Heat Pumps
Heat pumps will include a changeover
thermostat that senses an outside coil
switch-over temperature of 25°F,
Filter
lock-open refrigerant valve during heat
pump operation, temperature-activated
defrost drain and automatic emergency
heat operation to override the heat
pump’s changeover thermostat and
bring on electric resistance heaters in the
event of a sealed system failure. Unit will
not operate compressor and electric
heaters simultaneously.
The filter will be accessible without
removing room front. Filter material will
be nylon mesh, permanent cleanable.
Corrosion-Resistant Chassis (Standard
Option)
The condenser coil is painted using
cathodic electrocoat.The bottom ¼ of the
compressor is coated with a water borne
resin.The outdoor side of interior parts
are top coated, in addition, the base pan
is cathodic electrocoated.
20
PTAC-PRC001-EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Mechanical
Specifications
Unit Controls
Load Shedding Terminals
The unit controls will be full solid-state
and accessible from the top.The
standard unit mounted controls will
include two rotary (switch) knobs
controlling unit operational and
temperature mode.The unit operational
switch includes:
The LS/IN terminals will provide a
connection for a switch that can be
added to close the circuit and lockout the
compressor and electric heat when the
power company or energy management
system is trying to reduce its load for a
specific time.
• Off position.
• Fan only — unit operates on low fan
On Board Diagnostics
An LED light will flash a code displaying
8 conditions: Control OK, 24 Vac Fuse
Blown, ICT (Indoor CoilTemperature)
Probe Failure, Mode Switch Failure,
Potentiometer Failure, BadThermostat
Input Failure, Bad Communications in
Slave Mode, and IAT (Indoor Air
speed.
• Low cool — unit operates on low fan
speed to circulate air for cooling.
• High cool — unit operates on high fan
speed to circulate air for cooling.
• Low heat — unit operates on low fan
speed to circulate air for heating.
• High heat — unit operates on high fan
speed to circulate air for heating.
Temperature) Failure. A spare 500 MA
fuse has been provided on the board.
Temperature Limiter
Temperature Switch
The temperature limiting feature can
reduce energy costs by controlling the
maximum temperature in heating and
the minimum temperature in cooling.
The temperature switch is controlled by
turning the knob clockwise for a cooler
room temperature; turning it
counterclockwise will provide a warmer
room temperature. Adjusting the
thermostat to the mid setting (vertical)
will set the room temperature at
approximately 75°F.
Room Freeze Protection
Freeze protection is built into all units
and will activate the electric resistance
heater (when it senses a temperature of
40°F room temperature) to maintain an
above freezing temperature at the
sensor.
Remote Control Operation
To operate units with remote
thermostats, the Standard/Remote unit
mounted switch must be set to the
remote position.When in the remote
position, the unit will only respond to the
wall-mounted thermostat inputs. Unit
will operate on low or high fan.
Fan Cycle Switch
The fan cycle switch sets the operational
mode of the fan. In the ON position, the
fan will run continuously whenever the
unit is in the heat or cool position. In the
AUTO position, the fan will cycle on and
off with the compressor or electric heater
when the unit is in the cool or heat
mode.
Remote Thermostat/SensorTerminals
These terminals provide control inputs
for a remote thermostat or sensor.
Front Desk ControlTerminals
Automatic Emergency Heat Staged
Thermostat
These terminals provide control inputs
for a front desk switch.
On every unit mounted control heat
pump, electric heat engages
automatically if the sealed system or
compressor fails.
CompressorTime Delay
The compressor will not try to restart
once running or until approximately
three minutes have elapsed after
shutdown.
PTAC-PRC001-EN
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Options
Power Disconnect Switch Kit
ControlValves
Options
A power disconnect switch must be
installed in hard-wire junction or
subbase for use as a physical disconnect
where required by local codes.
24 volt water valves are available in
either two-way or three-way for 208/230
volt units and 265 volt units. 24 volt
steam valves are also available for
208/230 and 265 volt units.
Wall Sleeves
Wall sleeves shall be industry standard
size of 13¾”D x 42”W x 161/16”H.
Extended Wall Sleeves
Circuit Breaker Kit
Extended wall sleeves shall be industry
standard size of 18”D x 42”W x 161/16”H
or 24” D x 42”W x 161/16”H.
Remote/WallThermostats
A circuit breaker kit is installed in the
subbase to provide overcurrent
protection for proper 208/230 volt
amperage. Can also be used as a
physical disconnect where local codes
permit 208/230 volts.
Manual changeover thermostat
One-stage heat, One-stage cool and Off
Switch.
Drain Kit
Drain kit attaches to the bottom of the
wall sleeve for directional controlled
internal or external disposal of
condensate and defrost water.
Automatic changeover thermostat with
Two-stage Heat and One-stage Cool and
Off Switch.
Fuse Holder Kit
Fuses are included in 265 volt units. For
208/230 volts, these kits allow fusing in
15, 20 and 30 amps. Fuses are not
included. Fuse holders must be installed
in the unit or subbase.
Two-stage Heat (heat pump only) First
stage brings on electric coil when room
temperature is more than 3.8°F cooler
than thermostat setting; then electric
heat will turn off and heat pump cycles
on. Also one-stage Cool with Manual
Changeover.
Outdoor Grilles
Outdoor grilles are available as
architectural extruded, anodized
aluminum and four standard colors.
Special colors are also available or
standard stamped aluminum.
Hard-Wire Junction Box Kit
Provides for easy electrical connection
when permanent wiring is required.
Hard-wire kit must be used on 265 volt
units if subbases are not used.
Condenser Baffle Kit
Two-stage Heat and One-stage Cool with
Manual Changeover and Programmable.
The condenser baffle kit is required
when replacing an existing packaged
terminal unit and/or the original outdoor
grille is not made byTrane.These baffles
are required to deflect discharge air
away from the inlet, preventing
Remote Temperature Sensor
Duct Transition and Extended Kit
This temperature sensor overrides
standard unit mounted sensor to allow
temperature sensing on internal wall for
more accurate temperature control.
A main duct transition piece will attach to
the discharge of the unit and a duct
extension will be attached to the
transition piece to carry up to 40 percent
of the conditioned air to the adjoining
room.
recirculation of hot condenser air.
Condensate Removal Pump —Heat
Pump Only
Leveling Legs Kit
Attaches easily to the wall sleeve for
support and accurate unit leveling on
units without subbases. Adjustable from
25/8” to 5 ¼”.
The internal condensate pump serves as
an effective means for disposing of
condensate generated during heat pump
operation by transferring it to the indoor
coil.The warm coil surface and the warm
room air help in evaporation of the
condensate while adding humidity to the
room. As with any equipment of this
type, the addition of this kit will decrease
the sensible heating capacity of the unit.
This kit is not intended for use in
Powered Outside Vent
and Damper Kit
An optional power vent kit can be
installed to increase cfm to 95.The
power damper will automatically open
when the unit is operating and close
when not powered. Actual vent cfm
performance will vary due to application
and installation conditions.
Subbases
Subbases are prewired to facilitate field
electrical connections and include a
NEMA 6 or 7 configuration electrical
receptacle.The subbases include two
leveling screws for sleeve support and
accurate unit leveling during installation.
Subbases include locations for field
installation of physical disconnect
switches, cartridge-style fuse holders
and circuit breakers. Side skirts will be
included with subbases.
Hydronic Heat Kit
seacoast or corrosive environments.
The hydronic heat kit is a field-installed
package that can attach to air
No t e : Under extrem e high hum idity conditions, the
internal condensate pum p m ay not be able to dispose of
all the condensate produced, and condensate would
then drip from the outside of the wall sleeve. If this
condensation is unacceptable, then a drain system
(including factory approved drain kit for the wall sleeve)
should be installed.
conditioners to provide central system
hot water or steam heat capability on top
of units.The kit includes left or right-hand
piping.The units retain complete service
access with kit installed.
Control Cover Key Lock Kit
Allows the owner to lock the control
panel access to prevent unauthorized
operation.
22
PTAC-PRC001-EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Options
Subbase Kit
Condensate Drain Kit
Deflector Baffle Kit
The fully skirted subbase conceals wiring
while providing strong support. A plug-in
receptacle and field wiring access
expedites installation. Electrical
accessories such as fuse holders, circuit
breakers and disconnect switches meet
N.E.C. requirements.
This kit attaches to the wall sleeve base
pan for controlled internal or external
disposal of condensate and defrost
water.
The kit includes two air deflection baffles.
These deflectors direct the air in toward
the center and away from the inlet to
prevent recirculation of the hot
condenser air. This kit is not to be used
when the outdoor grille is provided by
Trane.
Outdoor Grilles
Outdoor grilles are available in stamped
aluminum and an attractive extruded
aluminum architectural grille.
Hard-Wire Kit
Fuse Holder Kit
This kit is used to permanently wire to
chassis when standard subbase and
power cord are not utilized.
Cartridge-style fuses can be installed in
the fuse holder for use in the subbase or
chassis. It is available in 15, 20 and 30
amp and included on the 265 volt unit.
Security Key Locks
Circuit Breaker Kit
The installation of Trane’s security key
locks helps prevent tampering of the
controls used to set temperature,
heating and cooling functions. Locks are
available for all PTAC models.
The circuit breaker kit, available in 15, 20,
25 or 30 amp, can be used withTrane’s
subbases. It gives overcurrent protection
and its location allows turning unit on or
off without tools.
PowerVent and Damper Kit
Power Disconnect Switch
Installation of the power vent can
increase the cfm to 70.The damper will
automatically close when unit is not
powered.
The power disconnect switch can be
used for 265 or 208/230 volt physical
disconnect where required by local
codes.The switch is rated at 30 amp
capacity.The switch is for use with
Trane’s standard subbases or hard
wire kit.
Power Door Kit
Door will power open to allow fresh air
when the unit fan is on and spring
closed when the unit fan is off.
Remote Temperature Sensor
This sensor allows for inexpensive
temperature sensing on an internal wall
for more accurate temperature control.
PTAC-PRC001-EN
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Warranty
Warranty Information
Standard Warranty
•Full First-Year Warranty
Trane will repair or replace, free of
charge including labor, any part which
proves to be defective due to
workmanship or materials.
•Full Five-Year Sealed System
Warranty
Trane will repair or replace, free of
charge including labor, the evaporator,
condenser, compressor or connecting
tubing which proves to be defective due
to workmanship or materials.
•Lim ited Second through Fifth Year
Warranty
During the 2nd through 5th year,Trane
will provide, free of charge, functional
parts which prove to be defective due to
workmanship or materials. Components
covered are switches, solenoids, fan
motors, thermostats, circuit boards,
factory installed heaters, blower wheel,
fan propeller and capacitor.
This limited warranty does not include
diagnostic time, labor or any
transportation and reinstallation charges
that may be required.
24
PTAC-PRC001-EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Literature Order Number
File Number
PTAC-PRC001-EN
PL-UN-PTAC-PRC001-EN-10-00
PTAC-DS-1 6/98
Supersedes
The Trane Com pany
An Am erican Standard Com pany
w w w .trane.com
Stocking Location
Inland - La Crosse
For more information contact your local
distributor (dealer), local district office, or Since TheTrane Company has a policy of continuous product and product data improvement, it reserves the
right to change design and specifications without notice.
Download from Www.Somanuals.com. All Manuals Search And Download.
|