OWNER'S MANUAL
DLP™ Projection Television
62CM9UA
Owner's Record
You will find the model number and serial number on
the back of the TV. Record these numbers in the spaces
provided below. Refer to them whenever you call upon
your TOSHIBA dealer regarding this product.
62CM9UE
72CM9UA
72CM9UE
Model number:
Serial number:
23566843
#01E01_6272CM9UAE
1
05.10.18, 3:23 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Toshiba 62/72CM9UA/E (E)
Black
Introduction
Important Safety Instructions
• See “Important notes about your DLP™ projection TV” on page 8.
• Be sure to observe the following instructions and precautions to ensure safe use of this TV.
Installation
Check!
Always connect the power plug to an electrical outlet equipped with
220 – 240V AC 50 Hz.
220-240V AC
Never use the TV outside the specified voltage range. It may cause a fire
or an electric shock.
WARNING ABOUT THREE-WIRE GROUNDING-TYPE PLUG:
Never remove the earthing pin on the power plug. This system is
equipped with a three pin earthing-type power plug. This plug will
only fit an earthing-type power outlet. This is a safety feature. If you
are unable to insert the plug into the outlet, contact an electrician to
replace the wall outlet.
About the fuse
In a three pin earthing-type, the fuse fitted
in this plug is approved by ASTA or BSI to
BS1362. It should only be replaced by a
correctly rated and approved type and the
fuse cover must be refitted.
Never defeat the purpose of the earthing plug.
Never insert or remove the power plug with wet hands.
This may cause electric shock.
Never place the TV in an unstabilized location such as on a shaky
table, incline or location subject to vibration.
The TV may drop or fall down which may cause injury or damage.
Never block or cover the slots and openings in the cabinet.
• Never place the TV so that it is facing upwards, or on its side.
• Never place the TV into a closet or bookshelf where the ventilation is
poor.
• Never spread a newspaper, tablecloth or curtain on the TV.
• When installing the TV against a wall, always keep the TV at least 10
cm from the wall.
• Never place the TV on a soft unstable surface, such as a carpet, or a
cushion.
The inside of this TV will overheat if the ventilation holes are covered,
blocked, or sealed, which may result in a fire.
Never place the TV near a heater or in direct sunlight.
The surface of the cabinet or power cord may melt and result in fire or
electric shock.
3
#01E03-08_6272CM9UAE
3
05.10.18, 3:23 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Toshiba 62/72CM9UA/E (E)
Black
Introduction
Important Safety Instructions (continued)
Installation (continued)
Never place the TV in an area exposed to high humidity levels, such as
in a bathroom or close to a humidifier.
This may cause a fire or an electric shock.
Never place the TV next to a stove where it will be exposed to oil,
smoke, or steam, or in a location where there is a large quantity of
dust.
This may cause a fire or electric shock.
Install the TV in a horizontal, stable location. Install a steady tie to
ensure that the TV is secure.
If the TV is not installed securely, it may lean or fall over and cause an
injury.
Sturdy tie
NOTICE OF POSSIBLE TV STAND INSTABILITY
Use this TV with the TOSHIBA TV stand recommended in the
“Specifications” section only.
Use with other stands may result in instability, causing possible injury
or death.
Hook
Precautions for moving the TV
• When moving the TV, be sure to remove the power plug from the wall
outlet and disconnect the antenna cable and audio/video cables, any
steady ties. Fire or electric shock may result if the power cord is
damaged.
• When carrying the TV, at least two people are needed. Be sure to carry
it upright.
• Never carry the TV with the screen facing up or down.
Precautions for installing on outdoor antenna
An outside antenna system should not be located in the vicinity of
overhead power lines, or other electric light or power circuits.
If the antenna falls down or drops, it may cause injury or electric shock
accidents.
4
#01E03-08_6272CM9UAE
4
05.10.18, 3:23 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Toshiba 62/72CM9UA/E (E)
Black
Use
Never place hot objects or open flame sources, such as lighted candles
or nightlights on, or close to the TV.
High temperatures can melt plastic and lead to fires.
Never place anything heavy on top of the TV.
This may cause the balance to become uneven, resulting in the TV falling
over, dropping or causing an injury.
The apparatus shall not be exposed to dripping or splashing and that
no objects filled with liquids, such as vases, shall be placed on the
apparatus.
When liquids are spilled or small items are dropped inside the TV, this
may cause a fire or an electric shock. If small objects drop inside the TV,
turn off the TV and remove the power plug from the outlet immediately
and contact a service technician.
Never insert objects (metal or paper) or pour water inside the TV from
ventilation holes and other places.
These items may cause a fire or an electric shock.
If these objects are inserted inside the TV, turn off the TV and remove the
power plug from the outlet immediately and contact a service technician.
Be especially careful that children do not insert objects in the TV.
Never stand or climb on the TV.
Be especially careful in households with children to prevent them from
climbing on top of the TV.
It may move, fall over, break, become damaged or cause an injury.
When the TV will not be used for a long period of time, such as during
vacation or travel, remove the power plug from the wall outlet for
safety.
5
#01E03-08_6272CM9UAE
5
05.10.18, 3:23 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Toshiba 62/72CM9UA/E (E)
Black
Introduction
Important Safety Instructions (continued)
Use (continued)
Never pull on the power cord when removing the plug from the wall
outlet.
Always hold the plug firmly when removing it. If the power cord is
yanked, the cord may become damaged and fire or electric shock may
occur.
Never cut, break, modify, twist, bunch up or bent the cord or apply
excessive force or tension to it.
Never place heavy objects on the cord or allow it to overheat as this may
cause damage, fire or electric shock. Contact a service technician if the
power cord is damaged.
If there is thunder or lightning, never touch the antenna cable or other
connected cables.
You may suffer an electric shock.
Service
Never repair, modify or disassemble the TV by yourself.
If it may cause a fire or an electric shock. Consult a service technician for
inspection and repairs.
When a malfunction occurs, or if smoke or an unusual odor comes
from the TV, turn off the TV and remove the power plug from the
outlet immediately.
Make sure that the smoke or smell has stopped, then contact a service
technician. If the TV is still used in this condition, it may then cause a fire
or an electric shock.
6
#01E03-08_6272CM9UAE
6
05.10.18, 3:23 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Toshiba 62/72CM9UA/E (E)
Black
Service (continued)
If the TV is dropped or the cabinet is broken, turn off the TV and
remove the power plug from the outlet immediately.
If the TV is still power used in this condition, it may cause a fire or an
electric shock or an injury. Contact a service technician for inspection.
When the TV reaches the end of its useful life, ask a qualified service
technician to properly dispose of the TV.
Note:
The lamp unit contains a small amount of mercury. Disposal of mercury
may be regulated due to environmental considerations.
Dispose of the used lamp unit by the approved method for your area. For
disposal or recycling information, please contact your local authorities.
Exemptions
■ Toshiba is not liable for any damage caused by fires, natural disaster (such as thunder, earthquake, etc.), acts by third
parties, accidents, owner's misuse, or uses in other improper conditions.
■ Toshiba is not liable for incidental damages (such as profit loss or interruption in business, modification or erasure of
record data, etc.) caused by use or inability to use of product.
■ Toshiba is not liable for any damage caused by neglect of the instructions described in the owner's manual.
■ Toshiba is not liable for any damage caused by misuse or malfunction through simultaneous use of this product and
the connected equipment.
Cleaning
Remove the power plug before cleaning.
Never use solvents such as benzine or thinner to clean the TV.
–
–
These solvents may distort the cabinet or damage its finish.
If rubber or vinyl products remain in contact with the TV for a long
time, a stain may result.
If the cabinet becomes dirty, clean it with a soft, dry cloth.
When cleaning the screen:
–
Wipe the screen gently with a soft, dry cloth.
Periodically disconnect the power plug from the outlet and check it.
If dust has collected on the power plug connectors, clean off the dust.
This dust may cause a fire due to reduced insulation on the plug.
Clean here
7
#01E03-08_6272CM9UAE
7
05.10.18, 3:23 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Toshiba 62/72CM9UA/E (E)
Black
Introduction
Important information
Important information
Important notes about your DLP™ projection TV
WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE TV COVERS. NO
USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
1)The light source for this TV is a projection lamp unit with a limited service life. When the lamp wears out, the picture may
become dark or black, or the lamp may fail, at which time you must replace the lamp unit.
The length of service life varies depending on product use and user settings. See “Selecting the lamp mode” on page 25 for
information on switching the lamp mode.
To replace the lamp unit
Please contact the nearest Toshiba Authorized Service Center or dealer:
• if the picture darkens and/or colors fade;
• if the screen (lamp) does not light (LED indication #3, page 45); or
• if you hear a loud noise and the picture goes black, which may indicate a lamp rupture (LED indication #3, page 45).
Only the replacement lamp unit model listed below can be used with this TV.
Using any other lamp may cause damage to the TV and/or lamp.
Model No.: D95-LMA ( Stock No. 23311168)
2)Each time you turn on the TV, it may take several minutes to go from no picture to full picture brightness.
3)The display of this TV is manufactured using an extremely high level of precision technology; however, an occasional pixel
(dot of light) may show constantly on the screen.
This is a structural property of DLP™ (Digital Light Processing™) technology in the TV, and is not a sign of malfunction.
Such pixels are not visible when the picture is viewed from a normal viewing distance.
4)Depending on the media you are viewing, it is possible, although unlikely, that a limited number of viewers may see a
“rainbow effect” on the screen, which can, in rare instances, result in eye fatigue. This is a rare occurrence related to
technology of this type, and is not a sign of TV malfunction.
5)Always sit approximately 3-8 m away from the TV and as directly in front of it as possible. The picture quality may be
affected by your viewing position and length of viewing time. If you sit too closely to the TV for too long, you may suffer
from eye fatigue.
6)This TV contains several cooling fans to moderate the internal temperature. You may be able to hear the fans for several
minutes after the TV is turned off. This is a function of the Quick restart feature and is not a sign of TV malfunction. You
can set the Quick restart feature to stop the fans as soon as the TV is turned off. See “Setting the Quick restart feature” on
page 33.
7)The orange and blue LED lights at the bottom center of the TV front indicate your TV’s current status. If either light
flashes, see “LED indications” on page 45 for details.
8)Review all safety and operating information in this owner’s manual before you use your TV.
The DLP logo and DLP medallion are trademarks of Texas Instruments.
About insecticide spray
• Never spray volatile compounds such as insecticide on the cabinet.
This may cause a discoloration or damage the cabinet.
Moisture Condensation
• If the room temperature suddenly rises (or if the TV is moved from a cool place to a hot place), condensation may occur on
the lenses resulting in picture distortion or color fading. In such a case, simply wait a while (with the power on) and the
condensation will evaporate.
8
#01E03-08_6272CM9UAE
8
05.10.18, 3:23 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Toshiba 62/72CM9UA/E (E)
Black
Getting started
Installation
Connecting an antenna
Optimum reception of color requires a good signal and will generally mean that an outdoor antenna must be used.
The exact type and positioning of the antenna will depend upon your particular area.
Your Toshiba dealer or service personnel can best advise you on which antenna to use in your area.
Do not plug the power cord until you have finished connecting the antenna.
VHF and/or
UHF antenna
300 Ω twin-lead feeder
75 Ω
antenna
Antenna adaptor
terminal
(not supplied)
The plug type
varies depending
on the models.
75 Ω coaxial cable
75 Ω
antenna
terminal
Plug
(not supplied)
Wall outlet
Installing the remote control batteries
Effective range
Remove the battery cover.
Insert two R03 (AAA) batteries matching the –/+
polarities of the battery to the –/+ marks inside the
battery compartment.
within 5 m
Notes:
Caution:
• If the remote control does not operate correctly,
or if the operating range becomes reduced,
replace both batteries with new ones.
• Dispose of batteries in a designated disposal
area. Do not throw batteries into a fire.
• Attention should be drawn to the environmental
aspects of battery disposal.
• If the batteries are dead or if you will not use the
remote control for a long time, remove the
batteries to prevent battery acid from leaking
into the battery compartment.
• Do not mix battery types or combine used
batteries with new ones.
9
#01E09-13_6272CM9UAE
9
05.10.18, 3:23 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Toshiba 62/72CM9UA/E (E)
Black
Getting started
Exploring your new TV
• You can operate your TV using the buttons on the right side panel or the remote control. The back and side of the
panel provide the terminal connections to connect other equipment to your TV. See “Equipment connections” on
pages 38-40.
• Model 62CM9UE is used in this manual for illustration purpose.
TV right side
For the use of each control, see the pages in brackets.
TV right side view
Headphones
(Not supplied)
TV control panel
Power [13]
Headphone jack
(3.5 mm, stereo)
EXIT [15]
Program position [19]
Menu [14]
Volume + – [19]
Menu [14]
(2) Video 2
input terminals [38]
Input source selection [31]
MENU [14]
Press here
to open.
Note:
Inserting the Headphone jack will mute the
sound from all speakers and deliver normal
stereo left and right sounds to the headphones.
TV front
TV front view
Remote sensor (behind the screen)
Power indicator (Blue) [45]
On-timer indicator (Orange) [32, 45]
10
#01E09-13_6272CM9UAE
10
05.10.18, 3:23 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Toshiba 62/72CM9UA/E (E)
Black
TV back
TV back view
WOOFER output terminal [30, 39]
HDMI 1 terminal [43]
Antenna input [9]
HDMI 2 terminal [43]
(C2) COMPONENT
VIDEO INPUT terminals [39]
RGB/PC input [40]
(C1) COMPONENT
VIDEO INPUT terminals [39]
HDMI (AUDIO) 1 terminals [43]
HDMI (AUDIO) 2 terminals [43]
AUDIO OUT terminals [28, 39]
(1) Video 1 input terminals [39]
MONITOR output terminals [39]
11
#01E09-13_6272CM9UAE
11
05.10.18, 3:23 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Toshiba 62/72CM9UA/E (E)
Black
Getting started
Learning about the remote control
Location of controls
For the use of each control, see the pages in brackets.
Teletext on/off [35 37]
–
CALL [17, 19]
Initial/index function for Teletext [37]
CALL
Power on/Standby [13]
(For Toshiba TV/VCR/DVD)
1
2
5
8
0
3
6
9
Number buttons (0-9) [19, 32]
4
7
• Input source selection [31]
(
1,
2,
C1,
C2,
HDMI 1, HDMI 2, PC)
• To access sub-pages when in
teletext [35]
To return to the previous program [19]
Picture mode selection [22]
Picture size selection [20]
MENU [14]
MENU
EXIT
EXIT [15]
P
DVD MENU
DVD
MENU
• Menu
• Program position
• Teletext [36]
[14]
[19]
• Menu
[14]
• Volume – + [19]
OK
Teletext control buttons [35, 36]
(Four colored buttons: Red, Green,
Yellow, Blue)
OK [14, 31]
P
Stereo/bilingual selection [27]
Bass boost on/off [30]
Sound mute [19]
TV
Mode switch
VCR
DVD
TV : To control TV
VCR : To control VCR
DVD : To control DVD
When in VCR or DVD mode:
(Only for Toshiba VCR/DVD
players)
When in Teletext mode [37]:
? To reveal concealed text
v To hold a wanted page
to PAUSE
to EJECT
to SKIP-REWIND
to SKIP-FORWARD
to PLAY
^ To enlarge teletext display size
When in TV mode [37]:
y/X To select a page while
viewing a normal picture.
To select the time display.
to STOP
to REWIND
to FAST FORWARD
12
#01E09-13_6272CM9UAE
12
05.10.18, 3:23 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Toshiba 62/72CM9UA/E (E)
Black
Getting started
Turning the TV on
• Plug the power cord into a wall outlet.
Switching on the TV
Side panel
After you plug in the TV power cord, make sure the blue LED on
the TV front is lit.
Press the
Power button on
1
Mono
the TV control panel or press
the button on the remote
control.
The orange LED will blink for
several seconds until the
picture appears.
Blue LED
Note:
Orange LED
The Quick restart setting will affect the amount of time it takes for
the picture to appear when you turn on the TV. See page 33 for
details.
Switching off the TV
CALL
Press the
Power button on the TV control panel or press
the button on the remote control to switch to the standby
mode.
1
2
5
8
0
3
6
9
4
7
Notes:
• When the TV will not be used for a long period of time, such as
during vacation or travel, remove the power plug from the wall
outlet.
• The TV will automatically turn off after approximately 15 minutes
if it is tuned to a vacant channel or a station that completes its
broadcast for the day. This function does not work in external
input mode or blue screen off mode.
• If power is cut off while you are viewing the TV, the Last Mode
Memory function turns on the TV automatically when power is
applied again. If power is going to be off for a long time and you
are going to be away from your TV, unplug the power cord to
prevent the TV from turning on in your absence.
MENU
EXIT
P
DVD
MENU
OK
P
Note:
If you watch black and white programs
when the color system mode is set to
Auto, color noise may appear on the
screen. In this case, select the appropriate
Color system (For the system of each
country or region, refer to pages 17 and
48).
13
#01E09-13_6272CM9UAE
13
05.10.18, 3:23 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Toshiba 62/72CM9UA/E (E)
Black
Getting started
Learning about the menu system
• We suggest you familiarize yourself with the display chart before using the menu system:
• Press the MENU button to display menu, then press the or button to select main menu headings.
• Press the or button to select an item.
• Press the or button to select or adjust setting.
• Press the OK button to display the next menu.
Menu display chart
PICTURE
menu
Picture settings
2/2
Low
Auto
Cool
MPEG NR
DNR
PICTURE
PICTURE
Picture settings
Color Temperature
Picture settings
1/2
Picture settings
Cinema mode
Lamp mode
OK
On
Low power
OK
On
Low power
100
Contrast
Brightness
Color
Cinema mode
Lamp mode
Contrast
100
50
50
0
Tint
0
Sharpness
Black stretch
On
MENU
EXIT
MENU
EXIT
Watch TV
Back
Watch TV
Back
MENU
EXIT
Watch TV
Back
SOUND
menu
SOUND
2/2
Off
Stable sound
SOUND
1/2
MTS
Auto
SOUND
1/2
Dual
Dual 1
Auto
Bass
Treble
Balance
WOW
0
0
0
MTS
Dual 1
0
Dual
Bass
OK
Treble
Balance
WOW
0
0
MENU
EXIT
Watch TV
Back
OK
MENU
EXIT
Watch TV
Back
SET UP
menu
SET UP
SET UP
English
OK
Language
Auto tuning
English
OK
Language
Auto tuning
Manual tuning
Program sorting
AV connection
Picture position
OK
Manual tuning
Program sorting
AV connection
Picture position
OK
OK
OK
OK
OK
OK
OK
MENU
EXIT
MENU
EXIT
Watch TV
Back
Watch TV
Back
TIMER
menu
TIMER
TIMER
00:00
00:00
01
Sleep timer
00:00
00:00
01
Sleep timer
On timer
On timer Position
On timer
On timer Position
MENU
EXIT
MENU
EXIT
Watch TV
Back
Watch TV
Back
FUNCTION
menu
FUNCTION
FUNCTION
Teletext
Teletext SW
FAST
1
Teletext
FAST
Teletext SW
1
Auto format
Blue screen
Side panel
On
On
1
Auto format
Blue screen
Side panel
On
On
1
On
Quick restart
OOnK
Quick restart
MENU
EXIT
MENU
EXIT
Watch TV
Back
Watch TV
Back
14
#01E14-19_6272CM9UAE
14
05.10.18, 3:23 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Toshiba 62/72CM9UA/E (E)
Black
Selecting a language
Choose from seven different languages (English, Chinese (CS),
Malay, Thai, Vietnamese, Russian, Arabic, Persian and French) for
the on-screen display.
Press the MENU button, then
press the or button to
display the SET UP menu.
SET UP
Language
Auto tuning
English
OK
CALL
Manual tuning
Program sorting
AV connection
Picture position
OK
OK
OK
1
4
7
2
5
8
0
3
6
9
OK
MENU
EXIT
Watch TV
Back
Press the or button to
select Language.
SET UP
English
OK
Language
Auto tuning
Manual tuning
Program sorting
AV connection
Picture position
Press the or button to
select the desired language.
OK
OK
OK
OK
MENU
EXIT
Watch TV
Back
MENU
EXIT
P
DVD
MENU
OK
P
Notes:
In the video input mode (
•
1,
2,
C1,
C2, HDMI 1,
HDMI 2), Auto tuning, Manual tuning and Program sorting are
not available. Instead, Manual setting appears in the SET UP menu
(see page 31).
• If you connect external equipment via component video source to
external input, Color system selection in the Manual setting menu
is not available.
TV
VCR
DVD
• If you do not make a selection for a while, the menu display
disappears automatically.
• If you want to close the menu display instantly, press the EXIT
button.
• To return to the previous menu, press the MENU button.
• The
buttons function as the Program position P /P
buttons when there is no menu display on the screen.
• The buttons function as the Volume – buttons when
there is no menu display on the screen.
+/
• In the PC input mode, PC Setting appears in the SET UP menu
(see page 41).
15
#01E14-19_6272CM9UAE
15
05.10.18, 3:23 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Toshiba 62/72CM9UA/E (E)
Black
Getting started
Programming channel memory
• First, use the Auto tuning function to preset all the active channels in your area automatically. Then, arrange the preset
channels with the Manual tuning function so that you can tune into only desired channels.
•
Use the Channel search operation if desired channels cannot be preset with the Auto tuning or if you would like to
preset channels to specific position numbers one by one.
System selection, Auto tuning
Press the MENU button, then
press the or button to
display the SET UP menu.
SET UP
English
OK
Language
Auto tuning
Manual tuning
Program sorting
AV connection
Picture position
OK
Press the or button to
select Auto tuning.
OK
CALL
OK
OK
MENU
EXIT
Watch TV
Back
1
4
7
2
5
8
0
3
6
9
Auto tuning
Press the OK button to display
Press OK key to start.
EXIT for no change.
!
the Auto tuning menu.
MENU
EXIT
Watch TV
Back
Auto tuning
Press the OK button to start the
automatic search.
The programming will begin
from the current position for all
available stations.
Searching
Pos :2
EXIT
Stop
The slide bar will move along the line as the search
progresses.
MENU
EXIT
P
DVD
MENU
If you make a mistake, simply repeat steps 1-4 to start again
from the beginning.
When the automatic search is complete, the TV will
automatically return to the first program position.
OK
Press the P or P button to select the programmed
position.
P
Manual tuning
TV
Press the MENU button, then
press the or button to
display the SET UP menu.
Press the or button to
select Manual tuning.
VCR
DVD
SET UP
English
OK
Language
Auto tuning
Manual tuning
Program sorting
AV connection
Picture position
OK
OK
OK
OK
MENU
EXIT
Watch TV
Back
Manual tuning
Label
Press the OK button to display
the Manual tuning menu.
Press the or button to
select the program position you
want to arrange.
Prog. Sys.
1
2
3
4
5
6
D/K
D/K
D/K
D/K
D/K
D/K
OK
Select
MENU
EXIT
Watch TV
Back
Manual tuning
Program
Press the OK button to display
the breakdown menu.
Press the or button to
select an item, then press the
or button to select the item as
shown on the next page.
1
A
D/K
Store
OK
MENU
EXIT
Watch TV
Back
C
E
A
G
D
B
F
16
#01E14-19_6272CM9UAE
16
05.10.18, 3:23 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Toshiba 62/72CM9UA/E (E)
Black
Manual tuning (continued)
A. Program position selection
B. Sound system (see page 48)
C. Color system (see page 48)
A : Automatic (factory set), P : PAL, S : SECAM
N4 : NTSC 4.43 (MHz), N3 : NTSC 3.58 (MHz)
If the color of a certain channel is abnormal, the automatic
color system selection (A) may have malfunctioned, or
sound system selection is wrong. In such a case, select
another color and/or sound system (see page 48).
D. Program position skip selection
CALL
1
4
7
2
5
8
0
3
6
9
Press the or button to turn the program position skip
option on “
” or off “
”.
The program position will then be skipped when you
select channels with the P or P button.
The “
” mark will appear beside a program position
number when you use the Number button on the remote
control.
E. Channel search operation
Press the button to search up the band or the button
to search down the band.
MENU
EXIT
P
DVD
MENU
Press the or button repeatedly until your desired
channel is displayed.
When a station/satellite is found, it will be displayed.
DO NOT PRESS ANY OTHER BUTTONS WHILE THE
SET IS TUNING.
OK
F. Auto Fine Tuning
Press the or button to turn the Auto Fine Tuning
option on “ ” or off “0”.
P
The Auto Fine Tuning function automatically corrects
slight fluctuations when receiving signals.
Manual Fine Tuning
While the Auto Fine Tuning turn off “0”, press the or
button so that the better picture and sound are obtained.
G. Label
TV
VCR
DVD
Station labels appear under the program position display
each time you turn on the TV, select a channel, or press
the CALL button.
To change or create station labels:
1) Press the or button repeatedly to select a
character for the first space, then press the button.
*(blank space)
2) Repeat step 1) to enter the rest of the characters. If you
would like a blank space in the label name, you must
choose a blank space from the list of characters.
Press the OK button to store your settings.
17
#01E14-19_6272CM9UAE
17
05.10.18, 3:23 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Toshiba 62/72CM9UA/E (E)
Black
Getting started
Programming channel memory (continued)
• This TV is capable of receiving a number of different channels depending upon where you live.
• Program sorting is an easy way of storing each channel on the program position of your choice.
Program sorting
Ex.: To swap channel ABCD (Prog.1) for channel MNOP (Prog.4):
Press the MENU button, then
press the or button to
SET UP
English
OK
Language
Auto tuning
display the SET UP menu.
Press the or button to
select Program sorting.
CALL
Manual tuning
Program sorting
AV connection
Picture position
OK
OK
OK
OK
1
2
5
8
0
3
6
9
MENU
EXIT
Watch TV
Back
4
7
Press the OK button to display
Program sorting
Label
Prog.
the Program sorting menu.
1
2
3
4
5
6
ABCD
EFGH
IJKL
MNOP
Press the or button to
select the channel ABCD, then
press the button.
Select
MENU
EXIT
Watch TV
Back
Program sorting
Label
MENU
EXIT
Prog.
P
Press the button to select the
new position “4”, then press
the button.
1
2
3
4
5
6
EFGH
IJKL
MNOP
DVD
MENU
ABCD
OK
Sort
Back
Store
EXIT
Watch TV
MENU
Program sorting
Label
Press the button to select the
channel MNOP, then press the
button.
Prog.
P
1
2
3
4
5
6
EFGH
IJKL
MNOP
ABCD
Press the button to select the
new position “1”, then press
the button.
Sort
Back
Store
MENU
EXIT
Watch TV
TV
VCR
DVD
Program sorting
Label
Prog.
1
2
3
4
5
6
MNOP
EFGH
IJKL
ABCD
Confirm new sorting list.
Select
MENU
EXIT
Watch TV
Back
18
#01E14-19_6272CM9UAE
18
05.10.18, 3:23 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Toshiba 62/72CM9UA/E (E)
Black
Getting started
Watching TV programs
Volume, Sound mute, Changing program positions, Program return, On-screen information
To alter the volume:
TV control panel
Press the
+ or
– button
to raise or lower the volume.
Volume
30
To mute the sound:
Press the
button. The word
Sound mute appears on the
screen.
Sound mute
Press the
button again to
restore the sound.
To change program position:
Enter the desired program
position number using the
Number buttons on the remote
control.
1
Mono
MNOP
CALL
For program positions below 10, use 0 and the required
number.
1
2
5
8
0
3
6
9
You can also change the program position by using the P or
button.
4
7
P
The program position will be displayed on the screen with
the Mono/Stereo/Dual audio status.
To switch between two program positions:
You can switch two program positions without entering actual
position number each time.
Select the first program
MENU
EXIT
2
3
EFGH
IJKL
Stereo
position you want to view.
P
DVD
MENU
Select the second program
position with the Number
buttons (0-9).
Dual
OK
Press the
button. The
previous channel will be
displayed.
Each time you press the
button, the TV will switch back and
P
forth between the two program positions.
To display the on-screen information:
Press the CALL button to
display the following on-screen
information.
The information will disappear
in 6 seconds.
4
ABCD
Stereo
TV
VCR
DVD
• Program position or external input mode selected
• Program skip on/off information
• Station label (if set)
Note:
The program position selection change
between different format channels takes
several seconds.
• Mono/Stereo/Dual audio status
To erase the display instantly, press the CALL button again.
19
#01E14-19_6272CM9UAE
19
05.10.18, 3:23 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Toshiba 62/72CM9UA/E (E)
Black
Using the TV’s features
Viewing the wide-screen picture format
• This TV is capable of showing broadcasts in a number of formats. Depending on the type of broadcast being
transmitted, you may select between Super live, Cinema, Subtitle, 14:9, Wide and 4:3.
Picture size selection
Press the button repeatedly to view the options available.
Super live
This setting will enlarge the 4:3
image to fit the screen by
stretching the image vertically and
CALL
horizontally, holding the correct
proportions at the center of the
1
4
7
2
5
8
0
3
6
9
image.
Cinema
When watching “letterbox format”
films/video tapes, this setting will
eliminate or reduce the black bars
at the top and bottom of the screen
by zooming in and selecting the
image without distortion.
MENU
EXIT
P
Subtitle
DVD
MENU
When subtitles are included on a
letterbox format broadcast, this
setting will raise the picture so that
the most of text is displayed.
OK
Subtitle
P
14:9
Use this setting when watching a
14:9 broadcast.
Notes:
• Using the special functions to change
the size of the displayed image (e.g.
changing the height/width ratio) for the
purpose of public display or
commercial gain may infringe on
copyright laws.
• The picture size selection is not
available for 720p and 1080i input
signals (fixed to Wide).
Wide
Use this setting when watching a
wide-screen DVD, wide-screen
video tape or a 16:9 broadcast
(when available). Due to the range
of wide-screen formats (16:9, 14:9,
20:9 etc.), you may see bars on the
top and bottom of the screen.
• If the aspect ratio of the selected format
is different from the one of the TV
transmission or video program, it can
cause a difference in vision. Change to
the correct aspect ratio picture size.
• When the PC input mode (see page 31)
is selected, the picture size selection is
wide or 4:3 only.
4:3
Use this setting to view a true 4:3
broadcast.
20
#01E20-30_6272CM9UAE
20
05.10.18, 3:23 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Toshiba 62/72CM9UR (E)
Black
Using the TV’s features
Picture position, Reset
Picture position adjustment
Adjustment to the position of the picture may be made to suit your
viewing preferences.
To adjust the picture position:
Press the MENU button, then
press the or button to
display the SET UP menu.
CALL
SET UP
English
OK
Language
Auto tuning
Manual tuning
Program sorting
AV connection
1
2
5
8
0
3
6
9
OK
OK
Press the or button to
select Picture position.
OK
OK
4
7
Picture position
MENU EXIT
Back
Watch TV
Picture position
Press the OK button to display
the Picture position menu.
0
0
Horizontal position
Vertical position
Reset
OK
The menu will vary depending
upon the widescreen format
you have previously chosen.
MENU
EXIT
Watch TV
Back
MENU
EXIT
P
Press the or button to
select an item you want to
adjust.
DVD
MENU
Press the or button to
adjust the settings as required.
Horizontal position
0
OK
P
Reset (Picture position adjustment)
This function resets your picture position settings to the factory
settings.
TV
VCR
DVD
To reset the picture position:
Press the MENU button, then
press the or button to
SET UP
display the SET UP menu.
English
Language
Auto tuning
OK
OK
OK
OK
OK
Manual tuning
Program sorting
AV connection
Picture position
Press the or button to
select Picture position, then
press the OK button.
MENU
EXIT
Watch TV
Back
Picture position
Press the or button to
select Reset, then press the OK
button.
0
0
Horizontal position
Vertical position
Reset
OK
Notes:
• When the picture format is in Wide or
4:3 mode, only the Horizontal position
can be adjusted.
MENU
EXIT
Watch TV
Back
• The picture position adjustment is not
available for 720p and 1080i input
signals.
21
#01E20-30_6272CM9UAE
21
05.10.18, 3:23 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Toshiba 62/72CM9UR (E)
Black
Using the TV’s features
Picture quality adjustment
Picture quality adjustment
To select the picture mode:
You can select the picture quality instantly among three preset
modes and one user-set mode.
• Press the button to select
CALL
the desired picture quality.
1
2
5
8
0
3
6
9
Dynamic, Standard, Mild and
Memory (user-set) can be selected
cyclically.
Dynamic
4
7
Mode
Picture quality
Dynamic
Standard
Mild
bright and dynamic picture
standard picture
soft picture
Memory
the picture quality you set
MENU
EXIT
P
DVD
MENU
Note:
In the PC input mode (see page 31), this mode is not available.
OK
To adjust the basic picture quality:
Picture settings
1/2
Press the MENU button, then
press the or button to
display the PICTURE menu.
100
50
50
0
Contrast
Brightness
Color
P
Tint
0
On
Sharpness
Black stretch
Press the or button to
select the Picture settings
menu, then press the OK
button.
MENU
EXIT
Watch TV
Back
TV
VCR
DVD
Contrast
100
Press the or button to
selects Contrast, Brightness,
Color, Tint or Sharpness, then
press the or button to
adjust the level.
Selection
Contrast
Brightness
Color
Tint
Sharpness
Pressing
lower
darker
paler
higher
lighter
deeper
greenish
sharper
Notes:
reddish
softer
• The Tint may only be adjusted on a tape
which has been recorded and played
back on an NTSC VCR.
• In the PC input mode (see page 31),
Color, Tint and Sharpness modes are
not selectable.
22
#01E20-30_6272CM9UAE
22
05.10.18, 3:23 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Toshiba 62/72CM9UR (E)
Black
To activate the black stretch
This function increases the strength of dark areas of the picture
which improves definition.
Picture settings
1/2
From the Picture settings
100
Contrast
Brightness
Color
menu, press the or button
to select Black stretch on the
2nd page.
50
50
0
CALL
Tint
0
Sharpness
Black stretch
On
1
4
7
2
5
8
0
3
6
9
MENU
EXIT
Watch TV
Back
Press the or button to
select On or Off.
On
Black stretch
Note:
This function is not available in the PC input mode (see page 31).
To activate the MPEG NR (Noise Reduction)
If MPEG pictures include mosquito noise (grainy outlines around
images within the picture which may result depending on
MENU
EXIT
P
compression and conversion rates), it may be reduced by using this
function.
DVD
MENU
From the Picture settings
menu, press the or button
to select MPEG NR on the 2nd
page.
Picture settings
2/2
Low
Auto
Cool
MPEG NR
OK
DNR
Color Temperature
MENU
EXIT
Watch TV
Back
P
Press the or button to
select Off, Low, Middle or
High.
High
MPEG NR
TV
Note:
VCR
DVD
This function is not available in the PC input mode (see page 31).
To activate the DNR (Digital Noise Reduction)
If the received signal is weak and the picture is blurry, the picture
may be improved by using this function.
Picture settings
2/2
From the Picture settings
menu, press the or button
to select DNR on the 2nd page.
Low
Auto
Cool
MPEG NR
DNR
Color Temperature
MENU
DNR
EXIT
Watch TV
Back
Auto
Press the or button to
select Auto, Low, Middle, High
or Off.
Note:
For 480i and 576i signals, the available selections are Auto, Low,
Middle, High or Off. For 1080i signals, the available selections are
Low, Middle, High or Off.
23
#01E20-30_6272CM9UAE
23
05.10.18, 3:23 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Toshiba 62/72CM9UR (E)
Black
Using the TV’s features
Picture quality adjustment (continued)
To select the color temperature
You can change the tone of the picture by selecting from three preset
color temperatures: Cool, Normal or Warm.
Press the MENU button, then
press the or button to
display the PICTURE menu.
Picture settings
2/2
Low
Auto
Cool
MPEG NR
DNR
Color Temperature
CALL
Press the or button to
select the Picture settings
menu, then press the OK
button.
1
2
5
8
0
3
6
9
MENU
EXIT
Watch TV
Back
4
7
Normal
Press the or button to
select Color Temperature on
the 2nd page, then press the
or button to select mode
you prefer.
Color Temperature
Cool
: Lends a blue hue to the picture.
MENU
EXIT
Normal : Neutral
P
Warm : Lends a red hue to the picture.
DVD
MENU
OK
To use the cinema mode
A movie film’s picture runs at 24 frames a second, whereas movie
P
software such as DVD, etc., that you enjoy watching on television at
home runs at 30 (NTSC) or 25 (PAL) frames a second. To convert
this signal to reproduce a smooth motion and picture quality, select
the On mode.
TV
Effective signal and setup conditions
• When the Video input mode is selected.
• When the input signal format is 480i and 576i.
VCR
DVD
Press the MENU button, then
press the or button to
display the PICTURE menu.
PICTURE
Picture settings
Cinema mode
Lamp mode
OK
On
Low power
Press the or button to
select Cinema mode, then press
the or button to select On
or Off.
MENU
EXIT
Watch TV
Back
On
Cinema mode
Note:
A DVD movie with a subtitle is input from a DVD player, the
Cinema mode may not work correctly.
24
#01E20-30_6272CM9UAE
24
05.10.18, 3:23 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Toshiba 62/72CM9UR (E)
Black
Selecting the lamp mode
You can select either the High bright or Low power lamp mode.
•
The High bright mode is useful when additional picture
brightness is desired (such as in a bright room).
• The Low power mode reduces wear on the projection lamp.
Using this mode should result in longer lamp life.
CALL
To select the lamp mode:
1
4
7
2
5
8
0
3
6
9
Press the MENU button, then
press the or button to
PICTURE
display the PICTURE menu.
Picture settings
Cinema mode
Lamp mode
OK
On
Low power
MENU
EXIT
Watch TV
Back
Press the or button to
select Lamp mode, then press
the or button to select
High bright or Low power,
whichever you prefer.
High bright
Lamp mode
MENU
EXIT
P
DVD
MENU
OK
P
TV
VCR
DVD
25
#01E20-30_6272CM9UAE
25
05.10.18, 3:23 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Toshiba 62/72CM9UR (E)
Black
Using the TV’s features
Sound adjustment
MTS (Multi-channel TV Sound) setting
Setting the MTS mode:
Auto mode
The MTS Auto mode automatically recognize stereo/bilingual
programs depending on the broadcast signal.
CALL
Press the MENU button, then
press the or button to
SOUND
1/2
display the SOUND menu.
Auto
MTS
1
2
5
8
0
3
6
9
Dual 1
Dual
Bass
Treble
Balance
WOW
0
0
0
Press the or button to
select MTS, then press the or
button to select Auto or
Mono.
4
7
OK
MENU
EXIT
Watch TV
Back
Mono mode
If you experience noise or poor reception of any stereo/bilingual
program, set the MTS mode to Mono.
Noise will be reduced and reception may improve.
MENU
EXIT
P
Note:
DVD
MENU
If you experience noise with a particular program on whose channel
reception is usually good, try setting MTS mode to Auto, then
switch the
button to
Mono (monaural) (see page 27).
OK
Selecting the Dual 1 or Dual 2 mode
P
You can hear only Dual 1 or Dual 2 sound selected, whenever
bilingual programs are received.
Press the MENU button, then press the or button to
display the SOUND menu.
TV
VCR
DVD
Press the or button to
select Dual, then press the or
SOUND
1/2
Auto
to select Dual 1 or Dual 2.
MTS
Dual 1
Dual
0
0
0
Bass
Treble
Balance
WOW
OK
MENU
EXIT
Watch TV
Back
Notes:
• When the MTS setting is in Mono mode, the Dual menu is not
selectable.
• The Dual menu setting status remains even if the TV is turned off.
26
#01E20-30_6272CM9UAE
26
05.10.18, 3:23 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Toshiba 62/72CM9UR (E)
Black
Stereo/Bilingual selection
To select the stereo programs:
When a stereo program is
10
ABCD
Stereo
received,
Stereo appears.
CALL
Press the
button to select
the stereo/monaural mode.
1
4
7
2
5
8
0
3
6
9
Stereo and
cyclically on the screen.
Mono appear
Stereo
To select the bilingual programs:
When a bilingual program is
received,
10
ABCD
Dual
Dual appears.
Press the
button to select
the sound to be heard. The
sound differs according to the
transmission system: NICAM
MENU
EXIT
Dual
1
P
DVD
MENU
or German stereo/bilingual broadcast.
Dual 1,
Dual 2
and
Mono appear cyclically on the screen.
OK
Sound to be heard
Display
German stereo/
NICAM
Sub I sound
Sub II sound
Main sound
bilingual broadcast
Main sound
Sub sound
—
P
Dual 1
Dual 2
Mono
Note:
TV
These settings are not stored in the TV memory.
VCR
DVD
Sound quality adjustment
To adjust the sound quality:
Press the MENU button, then
press the or button to
display the SOUND menu.
SOUND
1/2
Auto
Dual 1
MTS
Dual
0
0
0
Bass
Treble
Balance
WOW
Press the or button to
select Bass, Treble or Balance.
OK
MENU
EXIT
Watch TV
Back
Press the or button to
adjust the level.
Bass
0
Selection
Pressing
Bass
Treble
Balance
weaker
weaker
decreases the
right channel
stronger
stronger
decreases the
left channel
27
#01E20-30_6272CM9UAE
27
05.10.18, 3:23 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Toshiba 62/72CM9UR (E)
Black
Using the TV’s features
Sound adjustment (continued)
To select the audio output
With the Audio output function “Variable”, you can use the TV’s
remote controller to adjust the sound volume of the external audio
system connected (see page 39).
To select the sound volume from AUDIO OUT terminals:
CALL
Press the MENU button, then press the or button to
display the SET UP menu.
1
2
5
8
0
3
6
9
Press the or button to
select AV connection, then
4
7
SET UP
press the OK button to display
English
OK
Language
Auto tuning
Manual tuning
Program sorting
AV connection
Picture position
the AV connection menu.
OK
OK
OK
OK
MENU
EXIT
Watch TV
Back
AV connection
Press the or button to
select Audio output, then press
the or button to select
Variable or Fixed.
HDMI1 Audio
HDMI2 Audio
Woofer
Auto
Auto
MENU
EXIT
Internal
Variable
P
Audio output
DVD
MENU
MENU
EXIT
Watch TV
Back
OK
Note:
Make sure the volume control of your audio amplifier is set to a
moderate listening level.
P
To select the HDMI audio mode
You can select sound of the HDMI and DVI device audio connected
terminals (see page 43) from three modes : Auto, Digital and
Analogue.
TV
VCR
DVD
Press the MENU button, then press the or button to
display the SET UP menu.
Press the or button to
select AV connection, then
SET UP
English
OK
Language
Auto tuning
Manual tuning
Program sorting
AV connection
Picture position
press the OK button to display
the AV connection menu.
OK
OK
OK
OK
MENU
EXIT
Watch TV
Back
AV connection
Press the or button to
select HDMI 1 or HDMI 2, then
press the or button to
select Auto, Digital or
Analogue.
HDMI1 Audio
HDMI2 Audio
Woofer
Auto
Auto
Internal
Fixed
Audio output
MENU
EXIT
Watch TV
Back
28
#01E20-30_6272CM9UAE
28
05.10.18, 3:23 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Toshiba 62/72CM9UR (E)
Black
To use the WOW surround sound
WOW is a special combination of SRS Labs audio technologies that
creates a thrilling surround experience with deep, rich bass from
stereo sound sources. Your TV’s audio will sound fuller, richer and
wider.
CALL
Press the MENU button, then
press the or button to
SOUND
1/2
Auto
MTS
display the SOUND menu.
1
4
7
2
5
8
0
3
6
9
Dual 1
Dual
0
0
0
Bass
Treble
Balance
WOW
Press the or button to
select WOW, then press the OK
button.
OK
MENU
EXIT
Watch TV
Back
WOW
Press the or button to select
an item you want to adjust, then
press the or button to
Off
On
High
SRS 3D
FOCUS
TruBass
adjust the settings as required.
MENU
EXIT
Watch TV
Back
MENU
EXIT
P
•
•
•
SRS 3D: To turn On or Off the surround effect.
FOCUS: To turn On or Off the surround effect.
TruBass: To select your desired bass expansion level (Off, Low or
High).
DVD
MENU
OK
To use the Stable sound
When the signal source is changed, the Stable sound function limits
the high volume level to prevent extreme changes in volume. For
example, this will prevent the sudden increase in volume that often
happens when a TV program switches to a commercial.
P
From the SOUND menu, press
the or button to select
Stable sound on the 2nd page.
TV
SOUND
2/2
VCR
DVD
Stable sound
Off
On
Speaker
Press the or button to
select On or Off.
MENU
EXIT
Watch TV
Back
To activate/deactivate the speaker
Use this function to turn the TV speakers off when you connect an
audio system (see page 39).
Notes:
From the Sound menu, press
the or button to select
Speaker on the 2nd page.
• If the broadcast is monaural, the SRS 3D
effect does not work.
SOUND
2/2
Stable sound
Off
• WOW, SRS and
® symbol are
Speaker
On
trademarks of SRS Labs, Inc.
• WOW technology is incorporated under
license from SRS Labs, Inc.
Press the or button to
select On or Off.
MENU
EXIT
Watch TV
Back
29
#01E20-30_6272CM9UAE
29
05.10.18, 3:23 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Toshiba 62/72CM9UR (E)
Black
Using the TV’s features
Sound adjustment (continued)
Woofer Internal/External mode, Bass boost, Woofer system
To select the woofer Internal/External mode:
Press the MENU button, then press the or button to
display the SET UP menu.
AV connection
Press the or button to
CALL
HDMI1 Audio
HDMI2 Audio
Woofer
Auto
Auto
External
Fixed
select AV connection, then
press the OK button to display
the AV connection menu.
1
2
5
8
0
3
6
9
Audio output
Press the or button to
select Woofer, then press the
or button to select Internal
or External.
4
7
MENU
EXIT
Watch TV
Back
• Internal is to use the bass boost.
• External is to use the external woofer system.
To use the Bass boost:
Select Woofer Internal mode as shown above.
MENU
EXIT
P
DVD
MENU
Press the
button to display
Bass boost
70
Bass boost level.
OK
While the Bass boost display is
on the screen, press the or
button to adjust the Bass boost
level.
P
To turn off the Bass boost, press
Bass boost
Off
the
button to display Bass
boost Off.
TV
VCR
DVD
To use the external woofer system:
Woofer system
with amplifier
Connect the external woofer to
the “WOOFER” output terminal
located on the rear of the TV (see
page 39).
Select Woofer External mode
from the AV connection menu.
Press the
button to display
External Woofer
70
External Woofer level, then
press the or button to
adjust the External Woofer
level.
Note:
The Bass Boost effect is active only when
the sound outputs from the speaker or the
external woofer system.
To turn off the External Woofer,
External Woofer
Off
press the
button to display
External Woofer Off.
30
#01E20-30_6272CM9UAE
30
05.10.18, 3:23 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Toshiba 62/72CM9UR (E)
Black
Using the TV’s features
Input source selection
Input source selection
TV control panel
To select input source:
OK:
Press and hold the
button or
:
press the OK button on the
remote control until the video
input mode list appears on the
screen, then press the or
button to select appropriate
input source (or press the
button on the side panel or
button on the remote control
repeatedly to select required
input source directly).
(Press and hold)
5
4
3
2
1
C1
2
1
1
PC
HDMI2
HDMI1
0
PC
HDMI2
HDMI1
Ex. PC VGA mode
PC VGA
Press the OK button.
1 (
2 (
(1), video 1 input),
(2), video 2 input),
C1 ( (C1), COMPONENT VIDEO INPUT),
C2 ( (C2), COMPONENT VIDEO INPUT),
HDMI 1 ( HDMI 1 input),
CALL
HDMI 2 ( HDMI 2 input),
1
4
7
2
5
8
0
3
6
9
PC (
RGB/PC, PC input)
Manual setting:
Press the MENU button, then
press the or button to
display the SET UP menu.
SET UP
English
OK
Language
Manual setting
AV connection
Picture position
OK
OK
Press the or button to
select Manual setting, then
press the OK button.
MENU
EXIT
Watch TV
Back
MENU
EXIT
P
DVD
MENU
Press the or button to
select an item, then press the
or button to select the item
as shown below.
Manual setting
Color system:Auto
A
EXT1
OK
OK
MENU
Store
Back
EXIT
Watch TV
A
B
A. Color System
P
Confirm that color system is set to “A” (Auto). If not, select
“A” with the or button.
B. Video label
The video label allows you to label each input source for your TV.
To change or create video labels:
1) Press the or button repeatedly to select a character
for the first space, then press the button.
Notes:
• To return to the TV mode from the PC
input mode, press the button.
• When the component video input
HDMI 1, HDMI 2 or PC input mode is
selected, the MONITOR output
terminals (see page 39) output audio
signal only.
*(blank space)
2) Repeat step 1) to enter the rest of the characters.
If you would like a blank space in the label name, you
must choose a blank space from the list of characters3. 1
Press the OK button to store your settings.
#01E31-33_6272CM9UAE
31
05.10.18, 3:23 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Toshiba 62/72CM9UA/E (E)
Black
Using the TV’s features
Timer, Blue screen, Auto format
Timer
The Timer is especially useful if you
want the TV to turn itself on or off after a
selected period of time.
Activation of the Timer is indicated by
the orange “ On-timer indicator”, on
the front of the TV (see page 10).
To select the timer menu:
Press the MENU button, then
press the or button to
display the TIMER menu.
TIMER
00:00
00:30
03
Sleep timer
On timer
On timer Position
Press the or button to
select the required timer mode
(On timer or Sleep timer (Turn
off the TV)).
Side panel
MENU
EXIT
Watch TV
Back
Press the Number buttons (0-9), or button to set the On
or Off delay time, e.g. on in 30 minutes and program 3
selected.
Press the EXIT button to exit the menu. When setting the On
timer, press the or button to select the On timer Position
and enter the program position number you want to watch.
Set the Standby mode by pressing the button on the
On-timer
indicator
remote control or
Power button on the TV control panel.
Note:
The time display will set by 10 minutes, up to 12 hours 50 minutes.
To activate Blue screen
CALL
With the Blue screen function On, the screen will automatically turn
blue and the sound will be muted when no signal is being received.
1
4
7
2
5
8
0
3
6
9
Press the MENU button, then
press the or button to
FUNCTION
FAST
1
Teletext
display the FUNCTION menu.
Teletext SW
Auto format
Blue screen
Side panel
Quick restart
On
On
1
Press the or button to
select Blue screen.
OOnK
MENU
EXIT
Watch TV
Back
Press the or button to select On or Off.
Note:
MENU
EXIT
In the PC input mode (see page 31), the Blue screen is not available.
P
DVD
MENU
To use the Auto format
OK
When the TV receives a true HDMI picture and the Auto format is
On, it will automatically be displayed in HDMI format, irrespective
of the TV's previous setting.
P
From the FUNCTION menu,
press the or button to
FUNCTION
Teletext
LIST
select Auto format.
Teletext SW
Auto format
Blue screen
Side panel
Quick restart
1
On
On
1
Press the or button to
select On or Off.
On
MENU
EXIT
Watch TV
Back
32
#01E31-33_6272CM9UAE
32
05.10.18, 3:23 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Toshiba 62/72CM9UA/E (E)
Black
Using the TV’s features
Side panel adjustment, Quick restart
Side panel adjustment
You can adjust the brightness of side panel in 14:9 or 4:3 mode.
To adjust the Side panel setting:
Press the MENU button, then
press the or button to
display the FUNCTION menu.
FUNCTION
CALL
FAST
1
Teletext
Teletext SW
Auto format
Blue screen
Side panel
Quick restart
On
On
1
1
2
5
8
0
3
6
9
Press the or button to
select Side panel.
OOnK
MENU
EXIT
Watch TV
Back
4
7
Press the or button to
adjust the settings as required.
1
Side panel
Setting the Quick restart feature
MENU
EXIT
With the Quick restart feature set to ON, the TV will stay in
P
Shutdown mode for several minutes after the TV is turned off (see
Note below).
DVD
MENU
If the TV is turned on from Shutdown mode, the full picture
appears immediately.
OK
To set the Quick restart:
Press the MENU button, then
press the or button to
P
FUNCTION
FAST
1
Teletext
display the FUNCTION menu.
Teletext SW
Auto format
Blue screen
Side panel
Quick restart
On
On
1
Press the or button to
select Quick restart, then press
the or button to select On
or Off.
On
MENU
EXIT
Watch TV
Back
TV
VCR
DVD
Note:
If Quick restart is set to Off and you turn off the TV, it can take
several seconds for the picture to appear when you turn on the TV
again.
If Quick restart is set to On and you turn off the TV, the following
will occur for a few minutes:
• The screen (lamp) lights dimly.
• The fans continue to run.
This is a function of the Quick restart Shutdown mode and is not a
TV malfunction. If you do not prefer this, set the Quick restart
feature to Off.
When the Quick restart feature is set to Off, if you repeatedly turn
the TV on and off in a short period of time, the useful service life of
the lamp may be shorter than the average useful service life.
33
#01E31-33_6272CM9UAE
33
05.10.18, 3:23 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Toshiba 62/72CM9UA/E (E)
Black
Viewing teletext
Teletext – Setting up
• This TV has a multi-page teletext memory, which takes a few moments to load and it offers two ways of viewing
Teletext FAST and LIST which are explained on page 36.
Teletext mode
To select Teletext mode:
Select a channel position with the desired teletext service.
Press the MENU button, then
press the or button to
FUNCTION
CALL
Teletext
LIST
1
display the FUNCTION menu.
Teletext SW
Auto format
Blue screen
Side panel
Quick restart
On
On
1
1
4
7
2
5
8
0
3
6
9
Press the or button to
select Teletext.
On
OK
MENU
EXIT
Watch TV
Back
Press the or button to select FAST or LIST mode.
MENU
EXIT
P
DVD
MENU
OK
P
TV
VCR
DVD
Note:
When you are watching the teletext
program, SET UP menu and FUNCTION
menu are not selectable.
34
#01E34-37_6272CM9UAE
34
05.10.18, 3:23 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Toshiba 62/72CM9UA/E (E)
Black
Viewing teletext
About Teletext
Teletext general information
button:
Pressing the
button once will bring up the teletext screen.
Press again to superimpose the teletext over a normal broadcast
picture. Press again to return to normal TV mode. You need to
return to normal viewing if you wish to change channels.
CALL
When you first press the
button to access the text service, the
first page you see will be the initial page.
1
4
7
2
5
8
0
3
6
9
In FAST mode, this displays the main subjects available and their
relevant page numbers.
In LIST mode, you will see the page numbers currently stored on
the each color button.
Sub-pages:
Once in this chosen page, if there are sub-pages they will
automatically load into memory without changing the one you are
reading. If there are many sub-pages, it will take a long time for
them all to load and this will depend on the speed with which the
broadcaster transmits them.
MENU
EXIT
P
DVD
MENU
To access the sub-pages in memory, press the
then use the and buttons to view them.
(
) button,
OK
Teletext SW adjustment
P
If reception is weak, the picture may appear blurred, and text may
not appear clearly on the screen. In this case, use this function to
make text appear clearer.
TV
Press the MENU button, then
VCR
DVD
press the or button to
display the FUNCTION menu.
FUNCTION
Teletext
LIST
3
On
On
O1K
Teletext SW
Auto format
Blue screen
Side panel
Quick restart
On
MENU
EXIT
Watch TV
Back
Press the or button to select Teletext SW, then press the
or button to adjust 1, 2 or 3 modes.
Notes:
• This function may not be available in some cases.
• This function is available only in the antenna input signal mode.
35
#01E34-37_6272CM9UAE
35
05.10.18, 3:23 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Toshiba 62/72CM9UA/E (E)
Black
Viewing teletext
Teletext – FAST and LIST modes
Using FAST mode
There are two Modes: FAST will display
FASTEXT, if available. LIST will display your
four favorite pages. In either mode, as an
alternative to the colored buttons, you can
access a page by entering a 3-digit number,
using the Number buttons on the remote
control, or to advance to the next page, press
the P ( ) button, to go back to the previous
Press the
teletext.
button to access
100 Sport
14:57:55
If FASTEXT is available, you will
see 4 colored titles at the base of
the TV screen. To access any given
subject, simply press the relevant
colored button on the remote
control.
If FASTEXT is not available, you
can access any page simply by entering
a 3-digit page number or pressing the
corresponding colored button.
Football Baseball
Racing Swimming
Blue
Green
Red
page press the P
(
) button.
Yellow
To change between FAST and LIST, see page 34.
For further information on your particular text system(s), see the
broadcast teletext index page or consult your local Toshiba dealer.
CALL
Using LIST mode
1
4
7
2
5
8
0
3
6
9
100 TEXT M00
14:58:55
Press the
teletext.
button to access
The four choices at the bottom
of the screen are now number –
100, 200, 300 and 400, which
have been programmed into
the TV’s memory.
100
200
300
400
Blue
Green
Red
Yellow
To view these pages, use the
colored prompt buttons.
e.g. press the Green button to
view page 200.
MENU
EXIT
P
DVD
MENU
100 TEXT M00
14:58:59
If you want to change these
stored pages, press the colored
button for the color you want
to change.
OK
e.g. Press the Green button and
enter the 3-digit number.
P
R
B
100
250
300
400
G
Y
This number will change in the
top left of the screen and in the
colored highlight.
TV
VCR
DVD
Press the OK button to store your choice. The bars at the
bottom of the screen will flash white.
You may view other pages by simply entering the 3-digit
page number – but DO NOT press the OK button or you will
lose the favorite already stored.
36
#01E34-37_6272CM9UAE
36
05.10.18, 3:23 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Toshiba 62/72CM9UA/E (E)
Black
Viewing teletext
Teletext – Control buttons
• Below is an introduction to the teletext buttons on your remote control and their functions.
Teletext buttons on the remote control
Note:
To display a page of teletext:
button to display teletext. Press again to
superimpose the teletext over a normal broadcast picture. Press
again to return to normal TV mode.
It will not be possible to change
program position while in Teletext
mode, you will have to cancel the
teletext first by pressing the
button to return to a normal TV picture.
Press the
To display an index/initial page:
In FAST-mode
Press the
button to access the index page. The one
displayed is dependant on the broadcaster.
CALL
In LIST-mode
Press the
button to return to the 100 page or initial page.
1
4
7
2
5
8
0
3
6
9
To reveal concealed text:
Some pages cover topics such as quizzes and jokes. To discover the
solutions, press the
button.
To hold a wanted page:
This function is included as it is part of the broadcast teletext system
but you will not need it as this TV allows you to control the display
of sub-pages.
MENU
EXIT
To enlarge the teletext display size:
P
DVD
MENU
Press the
button once to enlarge the top half of the page, press
again to enlarge the bottom half of the page. Press again to revert to
the normal size.
OK
To select a page while viewing a normal picture:
When in teletext mode, if a page selection is made and then the
button is pressed, a normal picture will be displayed. The TV
will indicate when the page is present by displaying the title bar of
the text page at the top of the screen. Press the
the page.
P
button to view
TV
To select the time display:
VCR
DVD
9:56 and 25 seconds p.m.
If you press the
button while
watching a normal TV broadcast, you
will see a time display from the
broadcaster. It will remain on the
screen for about 5 seconds.
21:56:25
37
#01E34-37_6272CM9UAE
37
05.10.18, 3:23 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Toshiba 62/72CM9UA/E (E)
Black
Equipment connections
Side connections
•
You can connect a wide variety of auxiliary equipment via the terminals located on the right side of the TV
(2).
Connection example
Please always refer to the owner’s manual of the equipment to be connected for full details.
TV right side view
Press here to open.
Camcorder
Camcorder with S-Video
Video Games
• To select the side inputs, press and hold the
button until the video input mode list appears on the screen, then
press the or button to select
2 (see page 31), then press OK.
• Before connecting any external equipment, turn off all main power switches.
• Connect either the S-VIDEO input terminal or VIDEO input terminal, whichever terminal is used.
Never connect to both of these terminals.
• If you connect mono sound equipment to
on the TV.
(2), connect the audio output of the equipment to the L/MONO jack
38
#01E38-43_6272CM9UAE
38
05.10.18, 3:23 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Toshiba 62/72CM9UA/E (E)
Black
Equipment connections
Back connections
Connection example
DVD video player
(with component
video outputs)
HDMI device (see page 43)
DVI device (see page 43)
TV back view
Woofer system
with amplifier
(see page 30)
Set Top Box
Computer
VCR
(S-Video or Normal )
VCR (Recording)
Audio system
(see page 28, 29)
• Before connecting any external equipment, turn off the TV.
• The unauthorized recording of television programs, video tapes and other materials may infringe upon the
provisions of copyright laws.
• Connect either the S-VIDEO input terminal or VIDEO input terminal, whichever terminal is used.
Never connect to both of these terminals.
• In addition, there is a fixed/variable external audio output which enables the connection of a suitable audio
system. A 3.5 mm switched phono socket allows an external active Woofer system to be connected.
• The COMPONENT VIDEO INPUT consists of three component video jacks (Y, PB/CB, PR/CR) and provides the
best picture performance. These jacks can only be used with the component video compatible equipment, e.g. DVD
video player etc.
• Two HDMI (High-Definition Multimedia Interface) inputs receive digital audio and uncompressed digital video
from an HDMI device or uncompressed digital video from a DVI device.
• Additional equipment and cables shown are not supplied with this TV.
39
#01E38-43_6272CM9UAE
39
05.10.18, 3:23 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Toshiba 62/72CM9UA/E (E)
Black
Equipment connections
Connecting a computer (PC)
• An analog RGB (15 pin) computer cable can be connected.
To connect a computer
TV back view
Computer
Audio cable
for PC-to-TV
connection
Mini D-sub
15 pin
RGB PC cable
Conversion adapter
(if necessary)
Connect a PC cable from the computer to the RGB/PC terminal on the back of the TV.
The following signals can be displayed:
• VGA: VESA 640 x 480 @ 60 Hz
• SVGA: VESA 800 x 600 @ 60 Hz
• XGA: VESA 1024 x 768 @ 60 Hz
Notes:
• Some PC models cannot be connected to this TV.
• There is no need to use an adapter for computers with DOS/V compatible mini D-sub 15 pin terminal.
• A bar may appear in the upper, lower, right or left side of the screen, or parts of the picture may be obscured
depending on some signals. This is not the malfunction.
• If the edges of the picture are stretched, readjust the picture position adjustment in the PC Setting menu.
• Depending on the specification of the PC you are playing the DVD-Video on, and the DVD’s title, some scenes may
be skipped, or you may not be able to pause during multi-angle scenes.
Signal names for mini D-sub 15 pin connector
Pin No.
Signal name
Pin No.
Signal name
NC
Ground
NC
Pin assignment for RGB/PC
terminal
1
2
3
4
5
6
7
8
R
G
B
9
10
11
12
13
14
15
5
1
NC (not connected)
NC
Ground
Ground
Ground
NC
10
15
6
11
H-sync
V-sync
NC
40
#01E38-43_6272CM9UAE
40
05.10.18, 3:23 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Toshiba 62/72CM9UA/E (E)
Black
Equipment connections
PC setting
• In the PC input mode, you cannot select the Color, Tint, Black stretch, MPEG NR and DNR in the Picture setting
menu and Cinema mode (see page 14).
• In the PC input mode, the Manual setting (see page 31) is not displayed.
To adjust a PC setting
First press and hold the
button until the video input mode list
appears on the screen, then press the or and OK buttons in
order to select the PC input mode (see page 31).
To adjust the Picture size/position:
CALL
Press the MENU button, then
press the or button to
SET UP
1
2
5
8
0
3
6
9
display the SET UP menu.
English
OK
Language
AV connection
PC Setting
OK
4
7
Press the or button to
select PC Setting.
MENU
EXIT
Watch TV
Back
PC Setting
1/2
Press the OK button to display
the PC Setting menu.
0
0
0
0
0
0
Horizontal position
Horizontal width
Vertical position
Vertical height
Clock phase
MENU
EXIT
Sampling clock
P
MENU
EXIT
Watch TV
Back
DVD
MENU
Press the or button to
select an option you want to
adjust. (Picture size/position
menu: Horizontal position,
Horizontal width, Vertical
position and Vertical height)
OK
P
Horizontal position
0
Press the or button to
adjust the settings as required.
TV
VCR
DVD
41
#01E38-43_6272CM9UAE
41
05.10.18, 3:23 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Toshiba 62/72CM9UA/E (E)
Black
Equipment connections
PC setting (continued)
• If the clock phase, which synchronize the PC signal and TV display, is not optimized, the picture will blur.
This function enables you to adjust clock phase and display a clear picture.
• If the sampling clock does not synchronize with the dot clock frequency of the PC, blurred picture detail will occur,
or screen width will change, or drift patterns in vertical lines may be apparent.
This function enables you to adjust it and optimize the picture.
• The Reset function adjusts the PC Setting to the factory settings.
To adjust a PC setting (continued)
First press and hold the
button until the video input mode list
appears on the screen, then press the or and OK buttons in
order to select the PC input mode (see page 31).
To adjust the Clock phase of the picture:
CALL
Press the MENU button, then
press the or button to
SET UP
1
2
5
8
0
3
6
9
English
display the SET UP menu.
Press the or button
to select PC Setting.
Language
AV connection
PC Setting
OK
OK
4
7
MENU
EXIT
Watch TV
Back
PC Setting
1/2
Press the OK button, then press
the or button to select
Clock phase.
0
0
0
0
0
0
Horizontal position
Horizontal width
Vertical position
Vertical height
Clock phase
Sampling clock
MENU
EXIT
Watch TV
Back
MENU
EXIT
P
DVD
MENU
Press the or button to
obtain a clear picture.
Clock phase
0
OK
To adjust the Sampling clock:
From the PC Setting menu,
press the or button
to select Sampling clock.
PC Setting
1/2
0
0
0
0
0
0
Horizontal position
Horizontal width
Vertical position
Vertical height
Clock phase
P
Sampling clock
MENU
EXIT
Watch TV
Back
Press the or button to
optimize the picture.
Sampling clock
0
TV
VCR
DVD
To reset the PC Setting:
PC Setting
2/2
From the PC Setting menu,
press the or button to
select Reset on the 2nd page.
0
OK
Reset
MENU
EXIT
Watch TV
Back
Press the OK button.
Note:
The optimum points of the clock phase
and sampling clock adjustments may be
incomprehensible according to the input
signals.
42
#01E38-43_6272CM9UAE
42
05.10.18, 3:23 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Toshiba 62/72CM9UA/E (E)
Black
Equipment connections
Connecting an HDMI and a DVI device
• This TV is not intended for connection to and should not be used with a PC.
• When turnning on your electronic components, turn on the TV first, and then the HDMI or DVI device.
• When turnning off your electronic components, turn off the HDMI and DVI device first, and then the TV.
• This model may not be compatible with features and/or specifications that may be added in the future.
To connect an HDMI and a DVI device
The HDMI input on your TV receives digital audio and uncompressed digital video from an HDMI device and
uncompressed digital video from a DVI device.
This input is designed to accept HDCP program material in digital from EIA/CEA-861/861B compliant consumer
electronic devices (such as a set top box and DVD player with HDMI and DVI output).
The HDMI input is designed for best performance with 1080i (50 Hz/60 Hz) high-definition video signals, but will also
accept and display 480i, 480p, 576i, 576p and 720p (50 Hz) signals.
• HDMI: High-Definition Multimedia Interface
• DVI: Digital Video Interface
• HDCP: High-bandwidth Digital Content Protection
• EIA/CEA-861/861B compliance covers the transmission of uncompressed digital video with high-bandwidth digital
content protection, which is being standardized for reception of high-definition video signals. Because this is an
evolving technology, it is possible that some devices may not operate properly with the TV.
Note:
DO NOT CONNECT A PC USING THE HDMI PORT. ALWAYS use the VGA port provided to connect a PC.
To connect an HDMI device:
To connect a DVI device:
One HDMI (type A connector)-to-DVI adapter cable
and audio cables
One HDMI cable (type A connector)
TV back view
TV back view
DVI device
HDMI device
DVI
OUT
VIDEO
AUDIO
VIDEO
AUDIO
L
R
L
R
HDMI OUT
IN
IN
OUT
OUT
For proper operation, it is recommended that you use a
short HDMI cable.
HDMI cable transfers both video and audio. Separate
analog audio cables are not required.
HDMI (type A connector)-to-DVI adapter cable
For proper operation, the length of an HDMI-to-DVI
adapter cable should not exceed 3m. The recommended
length is 2m.
Some CDVs (video CDs) may not output digital audio
signals. In that case, you may hear sound by connecting
analog audio cables.
Standard analog audio cables
An HDMI-to-DVI adapter cable transfers only video.
Separate analog audio cables are required.
• HDMI, the HDMI logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI
Licensing , LLC.
43
#01E38-43_6272CM9UAE
43
05.10.18, 3:23 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Toshiba 62/72CM9UA/E (E)
Black
Reference section
Troubleshooting
• Before calling a service technician, please check the following table for a possible cause of the symptom and some
solutions.
Symptom and solution
Symptom
Solution
TV will not turn on
• Make sure the power cord is plugged in, then press
.
• The remote control batteries may be dead. Replace the batteries.
• The lamp unit may need to be replaced (page 8). Also see “LED
indications” on page 45.
No picture, no sound
No sound, picture OK
• Check the antenna connections.
• The sound may be muted. Press
• The station may have broadcast difficulties. Try another channel.
• Check that the Speaker function in SOUND menu is properly set.
+,
– or
.
Poor sound, picture OK
Poor picture, sound OK
• The station may have broadcast difficulties. Try another channel.
• Check the antenna connections.
• The station may have broadcast difficulties. Try another channel.
• Adjust the PICTURE menu.
Poor reception of broadcast channels
• Check the antenna connections.
• The station may have broadcast difficulties. Try another channel.
• Make sure the Color system is properly set.
Teletext problems
Multiple images
• Check the antenna connections.
Good performance of text depends on a good strong broadcast signal.
• The station may have broadcast difficulties. Try another channel.
• Antenna reception may be poor. Use a high directional outdoor
antenna.
• Check if the direction of the antenna has changed.
Poor color or no color
• The station may have broadcast difficulties. Try another channel.
• Adjust the Tint and/or Color in the PICTURE menu.
No picture or too dark
• The lamp unit may need to be replaced (page 8).
The remote control does not operate
• Remove all obstructions between the remote control and the remote
control sensor in the TV.
• The remote control batteries may be dead. Replace them with new
ones.
• Check that the TV/VCR/DVD switch on the remote control is
properly set.
44
#01E44-50_6272CM9UAE
44
05.10.18, 3:23 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Toshiba 62/72CM9UA/E (E)
Black
LED indications
The orange and blue LEDs on the TV (at the bottom center of the TV) indicate the TV’s status, as described below.
• Blue ON (solid) and Orange OFF = The TV power cord is plugged in.
• Orange ON (solid) and Blue OFF = The On timer is operating.
• Orange and/or Blue blinking (see table below).
TV front
Blue LED
Orange LED
LED Indication
Condition
Solution
1) Orange blinks
continuously at
3-second intervals.
Blue blinks
continuously at
0.5-second intervals.
The lamp unit door is not
seated properly.
Turn OFF the TV and unplug the power cord. Review
“How to replace the lamp unit” on page 47 to ensure that
the lamp door is installed securely. If the problem persists,
contact a Toshiba Authorized Service Center.
2) Orange blinks
continuously at
The lamp is not working
properly.
The TV will automatically try to restart itself eight times
(see item #3).
0.5-second intervals;
Blue is ON (solid).
3) Orange and Blue
blink
continuously at
1-second intervals.
The lamp is not working
properly after the eighth
automatic restart
Turn the TV OFF and then ON again. If the problem persists,
replace the lamp unit (see pages 46–47). If the problem still
exists, contact a Toshiba Authorized Service Center.
(see item #2).
4) Orange is OFF;
Blue blinks at
0.2-second intervals 4
times (repeat).
An abnormal temperature
increase has occurred.
Turn OFF the TV. Check to make sure all slots and open-
ings in the TV cabinet are not covered, blocked, or dusty.
Turn ON the TV again. If the problem persists, contact a
Toshiba Authorized Service Center.
5) Orange is OFF;
Blue blinks
continuously at
0.5-second intervals.
Abnormal operation
(including cooling fan
stop).
Turn OFF the TV and unplug the power cord. Plug the
power cord in again and turn ON the TV. If the problem
persists, contact a Toshiba Authorized Service Center.
6) Orange is OFF;
Blue blinks
continuously at
1-second intervals.
Abnormal operation of BUS Turn OFF the TV and unplug the power cord. Plug the
line.
power cord in again and turn ON the TV. If the problem
persists, contact a Toshiba Authorized Service Center.
7) Orange is OFF;
Blue blinks at
0.2-second intervals 3
times (repeat).
The color wheel has
stopped.
Turn OFF the TV and unplug the power cord. Plug the
power cord in again and turn ON the TV. If the problem
persists, contact a Toshiba Authorized Service Center.
45
#01E44-50_6272CM9UAE
45
05.10.18, 3:23 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Toshiba 62/72CM9UA/E (E)
Black
Reference section
Lamp unit replacement
The light source for this TV is a projection lamp unit with a limited service life. When the lamp wears out, the picture
may become dark or black, or the lamp may fail, at which time you must replace the lamp unit.
The length of service life varies depending on product use and user settings. See “Selecting the lamp mode” on page
25 for information on switching the lamp mode.
Replacing the lamp unit
Important information
WARNING: TO REDUCE THE RISK OF
• NEVER look directly at the lamp when lit as eye damage
ELECTRIC SHOCK, DO NOT REMOVE TV
could result. ALWAYS turn off the TV by unplugging the
COVERS. NO USER-SERVICEABLE PARTS
power cord before opening the lamp unit door and DO
INSIDE. REFER SERVICING TO QUALIFIED
NOT remove the back cover of the TV.
SERVICE PERSONNEL.
• The temperature of the lamp
When to replace the lamp unit
If you try to replace the lamp unit by yourself, read these
instructions carefully.
immediately after use exceeds 200˚C.
Allow the lamp to cool for at least 1
hour before replacing it, touching it
before it has cooled will result in severe
burns.
You should replace the lamp unit:
• if the picture darkens and/or colors fade;
• if the screen (lamp) does not light (LED indication #3,
page 45); or
• When replacing the lamp unit ALWAYS wear gloves to
reduce the risk of burns.
• if you hear a loud noise and the picture goes black, which
may indicate a lamp rupture (LED indication #3, page
45).
• The lamp unit door is provided with an interlock to
reduce the risk of electric shock and excessive ultraviolet
radiation.
Only the replacement lamp unit model listed below
can be used with this TV.
Using any other lamp may cause damage to the TV
and/or lamp.
• DO NOT attempt to replace the lamp unit without
removing the lamp unit door completely, failure to do so
could result in serious injury or death.
Model No.: D95-LMA ( Stock No. 23311168)
• If the lamp unit glass is accidentally touched or gets dirt
on it, it can be gently wiped clean with a lint-free
cleaning cloth such as a camera lens cloth or spectacles
cloth.
NEVER clean the lamp with any type of flammable or
aerosol cleaning liquid. Most household cleaning agents
contain chemicals that are flammable at high
temperatures.
• The lamp unit contains mercury. Disposal of mercury
may be regulated due to environmental considerations.
Dispose of the used lamp unit by the approved method
for your area. For disposal or recycling information,
please contact your local authorities.
46
#01E44-50_6272CM9UAE
46
05.10.18, 3:23 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Toshiba 62/72CM9UA/E (E)
Black
How to replace the lamp unit
Turn off the TV and remove the power plug from the
wall outlet.
Carefully insert the new lamp unit straight into the
TV until it is fully seated.
Allow the lamp to cool for at least 1 hour
before replacing it.
Notes:
• Never subject the lamp unit to excessive shock.
• Never touch the lamp unit glass or otherwise get it
dirty. Doing so may affect the image quality and
reduce the service life of the lamp.
On the lamp unit door on the side of the TV, loosen
the screw using a manual screwdriver, and then
remove the lamp unit door.
Using the manual screwdriver tighten the two
screws. Make sure that the screws are hand-tight
only, do not use an electric screwdriver to avoid
over-tightening.
Lamp unit door detail
TV back
Reattach the lamp unit door, making sure to insert
the hooks on the left side of the lamp unit door
inside the opening in the TV cabinet.
Loosen screw using manual screwdriver
Using a manual screwdriver, loosen the two screws
on the lamp unit.
Lamp unit door
Replace the screw and hand-tighten using a manual
screwdriver.
Plug in the power cord and turn on the TV. After the
initial warm up period (which may take several
seconds for full picture brightness), the TV should
now operate normally.
Lamp unit screws
If there is no picture, the picture is very dark or the
TV does not turn on, turn it back off and remove the
power plug from the wall outlet. Repeat steps 1 to 7
to ensure that the lamp unit has been installed
correctly.
Grasp the lamp unit handle and gently pull the lamp
unit straight out of the TV. Set the old lamp unit aside.
Remember to wear lint-free gloves when
replacing the lamp unit.
Put the old lamp into the now empty lamp unit box
and dispose of it according to local Government
guidelines. Make sure it is out of reach of children
and animals.
If you require further assistance, contact the nearest
Toshiba Authorized Service Center or dealer.
Note:
Wear soft, lint-free
gloves when
replacing the
lamp unit.
47
#01E44-50_6272CM9UAE
47
05.10.18, 3:23 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Toshiba 62/72CM9UA/E (E)
Black
Reference section
Broadcast system, Specifications
Broadcast transmission systems of each country or region
System
Area
Country or Region
Color
Sound
Bahrain, Kuwait, Israel, Oman, Qatar, United Arab Emirates, Yemen, etc.
Indonesia, Malaysia, Singapore, Thailand, etc.
PAL
B/G
China
China Hong Kong
PAL
PAL
SECAM
SECAM
NTSC
PAL
PAL
PAL
PAL
NTSC
D/K
I
B/G
D/K
M
B/G
I
N
Asia
M. E.
Iraq, Islamic Republic of Iran, Lebanon, Saudi Arabia, etc.
Russian Federation, etc.
Myanmar, etc.
Australia, New Zealand, etc.
Republic of South Africa, etc.
Argentina, Paraguay, Uruguay, etc.
Brazil
Oceania
Africa
South
M
M
America
Chile, Colombia, etc.
Note:
PAL, SECAM and NTSC 3.58 (MHz) are different color signal broadcast transmission systems applicable to different countries or
region. NTSC 4.43 (MHz) is used in special VCRs to playback NTSC recorded video tapes through PAL television equipment.
Specifications
Model
62CM9UA/62CM9UE/72CM9UA/72CM9UE
220V - 240V AC, 50 Hz
265W, 0.9W (standby)
62CM9UA/62CM9UE: 1,450mm (W) 475mm (D) 994mm (H)
72CM9UA/72CM9UE: 1,672mm (W) 550mm (D) 1,119mm (H)
62CM9UA/62CM9UE: 49.5kg, 72CM9UA/72CM9UE: 58.5kg
Channel coverage:
Power source
Power consumption
Dimensions
Mass (Weight)
Television system
(Antenna input)
PAL
PAL
PAL
B/G (CCIR)
VHF
2 - 12
UHF
CATV
VHF
21 - 69
X - Z+2, S1 - S41
I
(UK)
-
UHF
CATV
21 - 69
-
D/K (CHINA) VHF
1 - 12
UHF
13 - 57
CATV
Z1 - Z38
SECAM B/G (CCIR)
SECAM D/K (OIRT)
VHF
2 - 12
UHF
CATV
VHF
21 - 69
X - Z+2, S1 - S41
1 - 12
UHF
CATV
VHF
UHF
CATV
21 - 69
X1 - X19
NTSC
NTSC
M
M
(US)
2 - 13
14 - 69
A6 - A1, A - W, AA - ZZ, AAA, BBB
(JAPAN) VHF
UHF
1 - 12
13 - 62
M1 - M10, S1 - S41
CATV
Special RF signal:
NTSC 4.43 color system 5.5/6.0/6.5 MHz sound system
PAL 60 Hz color system 5.5/6.0/6.5 MHz sound system
48
#01E44-50_6272CM9UAE
48
05.10.18, 3:23 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Toshiba 62/72CM9UA/E (E)
Black
Specifications (continued)
COMPONENT VIDEO INPUT 480i, 480p, 576i, 576p, 720p (50/60 Hz), 1080i (50/60 Hz)
terminals (the signal format)
Color system
PAL, SECAM, NTSC 3.58/4.43
16 : 9
Aspect ratio
Visible size (diagonal)
62CM9UA/62CM9UE: 1,575 mm
72CM9UA/72CM9UE: 1,829 mm
Audio power
15 W + 15 W (10% THD)
120 mm (round) 4pcs.
(1) Input
Speakers
Input/Output terminals
4 pin
S-video
A/V
S-video
A/V
Phono jacks
4 pin
(2) Input
(C1) Input
(C2) Input
Phono jacks
Component video Y, PB/CB, PR/CR
Phono jacks
Audio L/Mono + R
Component video Y, PB/CB, PR/CR
Phono jacks
Phono jacks
Phono jacks
Phono jack
Mini D-sub 15 pin Analog RGB
3.5 mm stereo mini jack
Audio L/Mono + R
A/V
Audio L + R (Fixed/Variable)
Bass Line out (Variable)
MONITOR Output
AUDIO OUT Output
Woofer
RGB/PC
AUDIO
HDMI 1
Output
Input
Input
Input (type A ) 19pin
A/V Digital
Analog L+R
A/V Digital
Analog L+R
HDMI (AUDIO) 1 Input
Phono jacks
HDMI 2
Input (type A ) 19pin
HDMI (AUDIO) 2 Input
Phono jacks
Headphones jack 3.5 mm (Diameter) stereo
Supplied accessories
Optional stand
Owner’s manual (1),
Remote control (1),
Batteries (2)
62CM9UA/62CM9UE: ST6202S
72CM9UA/72CM9UE: ST7202S
• Design and specifications are subject to change without notice.
• Never service or remodel the TV by yourself. It may expose you to a fire hazard or dangerous voltages.
49
#01E44-50_6272CM9UAE
49
05.10.18, 3:23 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Toshiba 62/72CM9UA/E (E)
Black
TOSHIBA CORPORATION
YC/P
#01E44-50_6272CM9UAE
50
05.10.18, 3:23 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Black
Toshiba 62/72CM9UA/E (E)
|
Teac Computer Drive CD58E User Manual
Teledex Telephone Opal RediDock User Manual
TOA Electronics Cell Phone SCP 2700 User Manual
Toshiba Computer Drive MK2533GSG User Manual
TP Link Webcam TL WA5110G User Manual
Troy Bilt Snow Blower 5210R User Manual
Viking Ventilation Hood VIL1200 User Manual
VistaQuest Digital Camera PC30I User Manual
Vizio Laptop CT14 A0 User Manual
Vornado Electric Heater TAVH10 User Manual