Introduction
Connections
Basic setup
2
DIGITAL VIDEO
13
18
20
28
31
40
44
COMBINATION FLAT COLOR
TELEVISION AND DVD
VIDEO PLAYER
TV operation
Basic playback
MD20FP1
OWNER’S MANUAL
Advanced playback
Function setup
Others
©2004 Toshiba Corporation
Before operating the unit, please read this manual thoroughly.
5K70101B [E] (Cover)
1
20/4/04, 15:51
Download from Www.Somanuals.com. All Manuals Search And Download.
1. READ INSTRUCTIONS
All the safety and operating instructions should be read before the unit is operated.
2. RETAIN INSTRUCTIONS
The safety and operating instructions should be retained for future reference.
3. HEED WARNINGS
All warnings on the unit and in the operating instructions should be adhered to.
4. FOLLOW INSTRUCTIONS
All operating and use instructions should be followed.
5. CLEANING
Unplug this unit from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners.
Use a damp cloth for cleaning the exterior cabinet only.
6. ATTACHMENTS
The manufacturer of this unit does not make any recommendations for attachments, as they may cause
hazards.
7. WATER AND MOISTURE
Do not use this unit near water. For example, near a bathtub, washbowl, kitchen sink, laundry tub, in a wet
basement, or near a swimming pool.
PORTABLE CART WARNING
(symbol provided by RETAC)
8. ACCESSORIES
Do not place this unit on an unstable cart, stand, tripod, bracket, or table.
The unit may fall, causing serious injury, and serious damage to the unit.
8A. An appliance and cart combination should be moved with care. Quick stops,
excessive force, and uneven surfaces may cause the appliance and cart
combination to overturn.
9. VENTILATION
Slots and openings in the cabinet back or bottom are provided for ventilation,
and to ensure reliable operation of the unit, and to protect it from overheating.
S3126A
These openings must not be blocked or covered. The openings should never be blocked by placing the unit
on a bed, sofa, rug, or other similar surface. This unit should never be placed near or over a radiator or heat
source. This unit should not be placed in a built-in installation such as a bookcase or rack unless proper
ventilation is provided or the manufacturer’s instructions have been adhered to.
10. POWER SOURCE
This unit should be operated only from the type of power source indicated on the rating plate. If you are not
sure of the type of power supply to your home, consult your appliance dealer or local power company. For
units intended to operate from battery power, or other sources, refer to the respective pages on this Own-
er's Manual for their operating instructions.
11. GROUNDING OR POLARIZATION
This unit is equipped with a polarized alternating-current line plug (a plug having one blade wider than the
other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert
the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to
replace your obsolete outlet. Instead of the polarized alternating-current line plug, your unit may be
equipped with a 3-wire grounding-type plug (a plug having a third (grounding) pin). This plug will only fit into
a grounding-type power outlet. This too, is a safety feature. If you are unable to insert the plug into the
outlet, contact your electrician to replace your obsolete outlet.
Do not defeat the safety purpose of the grounding-type plug.
12. POWER-CORD PROTECTION
Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed
upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point
where they exit from the appliance.
3
5K70101B [E] (P02-05)
3
20/4/04, 15:51
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
IMPORTANT SAFEGUARDS
(Continued)
13. LIGHTNING
To protect your unit from a lightning storm, or when it is left unattended and unused for long periods of time,
unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the
unit due to lightning and power line surges.
14. POWER LINES
An outside antenna system should not be located in the vicinity of overhead power lines or other electric
light or power circuits, or where it can fall onto or against such power lines or circuits. When installing an
outside antenna system, extreme care should be taken to keep from touching such power lines or circuits,
as contact with them might be fatal.
15. OVERLOADING
Do not overload wall outlets and extension cords, as this can result in a risk of fire or electric shock.
16. OBJECT AND LIQUID ENTRY
Do not push objects through any openings in this unit, as they may touch dangerous voltage points or short
out parts that could result in fire or electric shock. Never spill or spray any type of liquid into the unit.
17. OUTDOOR ANTENNA GROUNDING
If an outside antenna or cable system is connected to the unit, be sure the antenna or cable system is
grounded to provide some protection against voltage surges and built-up static charges, Section 810 of the
National Electrical Code (NEC), ANSI/NFPA 70, provides information with respect to proper grounding of
the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of
grounding conductors, location of antenna discharge unit, connection to grounding electrodes, and require-
ments for the grounding electrode.
18. SERVICING
Do not attempt to service this unit yourself as opening or removing covers may expose you to dangerous
voltage or other hazards. Refer all servicing to qualified service personnel.
For example:
a. When the power-supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into the unit.
c. If the unit has been exposed to rain or water.
d. If the unit does not operate normally by following the operating instructions. Adjust only those
controls that are covered by the operating instructions, as an improper adjustment of other controls
may result in damage and will often require extensive work by a qualified technician to restore the
unit to its normal operation.
e. If the unit has been dropped or the cabinet has been damaged.
f. When the unit exhibits a distinct change in performance, this indicates a need for service.
19. REPLACEMENT PARTS
When replacement parts are required, be sure the service technician uses replacement parts specified by
the manufacturer or those that have the same characteristics as the original part.
Unauthorized substitutions may result in fire, electric shock or other hazards.
20. SAFETY CHECK
Upon completion of any service or repairs to this unit, ask the service technician to perform safety checks to
determine that the unit is in proper operating condition.
21. HEAT
The product should be situated away from heat sources such as radiators, heat registers, stoves, or other
products (including amplifiers) that produce heat.
22. DISC TRAY
Keep your fingers well clear of the disc tray as it is closing. It may cause serious personal injury.
23. CONNECTING
When you connect the product to other equipment, turn off the power and unplug all of the equipment from
the wall outlet. Failure to do so may cause an electric shock and serious personal injury. Read the owner's
manual of the other equipment carefully and follow the instructions when making any connections.
24. SOUND VOLUME
Reduce the volume to the minimum level before you turn on the product. Otherwise, sudden high volume
sound may cause hearing or speaker damage.
25. SOUND DISTORTION
Do not allow the product output distorted sound for a longtime. It may cause speaker overheating and fire.
26. HEADPHONES
When you use the headphones, keep the volume at a moderate level. If you use the headphones continu-
ously with high volume sound, it may cause hearing damage.
4
5K70101B [E] (P02-05)
4
20/4/04, 15:51
Download from Www.Somanuals.com. All Manuals Search And Download.
27. LASER BEAM
Do not look into the opening of the disc tray or ventilation opening of the product to see the source of the
laser beam. It may cause sight damage.
28. DISC
Do not use a cracked, deformed, or repaired disc. These discs are easily broken and may cause serious
personal injury and product malfunction.
29. NOTE TO CABLE TV SYSTEM INSTALLER
This reminder is provided to call the Cable TV system installer’s attention to Article 820-40 of the NEC that
provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be con-
nected to the grounding system of the building, as close to the point of cable entry as practical.
EXAMPLE OF ANTENNA GROUNDING AS PER THE
NATIONAL ELECTRICAL CODE
ANTENNA LEAD
IN WIRE
GROUND
CLAMP
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
ELECTRIC SERVICE
EQUIPMENT
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
NEC-NATIONAL ELECTRICAL CODE
S2898A
IMPORTANT RECYCLING INFORMATION
This product uses both Cathode Ray Tube (CRT) and other components that contain lead. In
your community there might be regulations that require you to dispose these materials
properly under environmental considerations. Please contact your local authorities, or the
Power source
TO USE AC POWER SOURCE
AC Outlet
Use the AC polarized line cord provided for operation on AC. Insert the AC cord plug
into a standard 120V 60Hz polarized AC outlet.
Wider Hole
and Blade
Notes:
Never connect the AC line cord plug to other than the specified voltage (120V
60Hz). Use the attached power cord only.
•
If the polarized AC cord does not fit into a non-polarized AC outlet, do not attempt to
file or cut the blade. It is the user’s responsibility to have an electrician replace the
obsolete outlet.
•
If you cause a static discharge when touching the unit and the unit fails to function,
simply unplug the unit from the AC outlet and plug it back in. The unit should return
to normal operation.
If the AC cord plug is plugged in for the first time, wait for approx. 5 seconds before
pressing the POWER button.
•
•
Polarized AC Cord Plug
(One blade is wider than the other.)
5
5K70101B [E] (P02-05)
5
20/4/04, 15:51
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Precautions
Notes on handling
Notes on moisture condensation
3 When shipping the unit, the original shipping carton
and packing materials come in handy. For maximum
protection, repack the unit as it was originally packed
at the factory.
3 Do not use volatile liquids, such as insect spray, near
the unit. Do not leave rubber or plastic products to
contact the unit for prolonged period. They will leave
marks on the finish.
Moisture condensation damages the unit. Please
read the following carefully.
Moisture condensation occurs, for example, when you
pour a cold drink into a glass on a warm day. Drops of
water form on the outside of the glass. In the same way,
moisture may condense on the optical pick-up lens
inside this unit, one of the most crucial internal parts of
the unit.
3 The top and rear panels of the unit may become
warm after a long period of use. This is not a
malfunction.
o
f
n
s
3 When the unit is not in use, be sure to remove the
disc and turn off the power.
3 If you do not use the unit for a long period, the unit
may not function properly in the future. Turn on and
use the unit occasionally.
Optical pick-up
lens
3 Moisture condensation occurs during the
following cases.
Notes on locating
When you bring the unit directly from a cold place to
a warm place.
3 Place the unit on a level surface. Do not use it on a
shaky or unstable surface such as a wobbling table or
inclined stand. The loaded disc may become dis-
aligned and damage the unit.
3 When you place this unit near a TV, radio, or VCR,
the playback picture may become poor and the sound
may be distorted. In this case, place the unit away
from the TV, radio, or VCR.
When you use the unit in a room where you just
turned on the heater, or a place where the cold wind
from the air conditioner directly hits the unit.
In summer, when you use the unit in a hot and humid
place just after you move the unit from an air
conditioned room.
When you use the unit in a humid place.
Notes on cleaning
Use a soft, dry cloth for cleaning.
For stubborn dirt, soak the cloth in a weak detergent
solution, wring well and wipe. Use a dry cloth to wipe
it dry.
Do not use any type of solvent, such as thinner and
benzine, as they may damage the surface of the unit.
If you use a chemical saturated cloth to clean the unit,
follow that product’s instructions.
3 Do not use the unit when moisture condensation
may occur.
If you use the unit in such a situation, it may damage
discs and internal parts. Remove the disc, connect
the power cord of the unit to the wall outlet, turn on
the unit, and leave it for two or three hours. After two
or three hours, the unit will have warmed up and
evaporated any moisture. Keep the unit connected to
the wall outlet and moisture condensation will seldom
occur.
To obtain a clear picture
The unit is a high technology, precision device. If the
optical pick-up lens and disc drive parts are dirty or worn
down, the picture quality will deteriorate. To obtain a
clear picture, we recommend regular inspection and
maintenance (cleaning or parts replacement) every
1,000 hours of use depending on the operating
environment. For details, contact your nearest dealer.
Wall outlet
6
5K70101B [E] (P06-07)
6
20/4/04, 15:51
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes on discs
On handling discs
Structure of disc contents
Do not touch the playback side of the disc.
Normally, DVD video discs are divided into titles, and
the titles are sub-divided into chapters. Video CDs and
Audio CDs are divided into tracks.
DVD video disc
DVD video disc
Title 1
Title 2
Chapter 1 Chapter 2
Chapter 1 Chapter 2 Chapter 3
Playback side
Do not attach paper or tape to discs.
Video CD/Audio CD
Video CD/Audio CD
Track 1
Track 2
Track 3
Track 4
Track 5
On cleaning discs
Fingerprints and dust on the disc cause picture and
sound deterioration. Wipe the disc from the center
outwards with a soft cloth. Always keep the disc
clean.
Each title, chapter or track is assigned a number, which
is called “title number”, “chapter number” or “track
number” respectively.
There may be discs that do not have these numbers.
Notes on copyright
It is forbidden by law to copy, broadcast, show,
broadcast on cable, play in public, and rent copyrighted
material without permission.
If you cannot wipe off the dust with a soft cloth, wipe
the disc lightly with a slightly moistened soft cloth and
finish with a dry cloth.
Do not use any type of solvent such as thinner,
benzine, commercially available cleaners or antistatic
spray for vinyl LPs. It may damage the disc.
DVD video discs are copy protected, and any recordings
made from these discs will be distorted.
This product incorporates copyright protection
technology that is protected by method claims of certain
U.S. patents and other intellectual property rights owned
by Macrovision Corporation and other rights owners.
Use of this copyright protection technology must be
authorized by Macrovision Corporation, and is intended
for home and other limited viewing uses only unless
otherwise authorized by Macrovision Corporation.
Reverse engineering or disassembly is prohibited.
On storing discs
Do not store discs in a place subject to direct sunlight
or near heat sources.
Do not store discs in places subject to moisture and
dust such as a bathroom or near a humidifier.
Store discs vertically in a case. Stacking or placing
objects on discs outside of their case may cause
warping.
7
5K70101B [E] (P06-07)
7
20/4/04, 15:51
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Notes on discs (Continued)
About this owner’s manual
Playable discs
This owner’s manual explains the basic instructions of
this unit. Some DVD video discs are produced in a
manner that allows specific or limited operation during
playback. As such, the unit may not respond to all
operating commands. This is not a defect in the unit.
Refer to instruction notes of discs.
This unit can play the following discs.
Maximum
playback time
Disc
Disc Mark Contents
Size
Approx. 4 hours
(single sided disc)
12 cm
Audio
+
Video
(moving
pictures)
“
” may appear on the TV screen during operation.
Approx. 8 hours
(double sided disc)
A “ ” means that the operation is not permitted by the
unit or the disc.
For example, sometimes it is unable to stop the
playback of copyright message of the disc when the
STOP (3) button is pressed. Alternatively, the “ ” may
also indicate that the feature is not available for the disc.
DVD
video
discs
Approx. 80 minutes
(single sided disc)
8 cm
Approx. 160 minutes
(double sided disc)
Notes on region numbers
Approx. 74 minutes
Approx. 20 minutes
12 cm
Audio
+
Video
(moving
pictures)
The region number of this unit is 1. If region numbers,
which stand for their playable area, are printed on your
Video
CDs
ALL
1
DVD video disc and you do not find
or
, disc
DIGITAL VIDEO
8 cm
playback will not be allowed by the player. (In this case,
the unit will display a message on-screen.)
Approx. 74 minutes
Approx. 20 minutes
12 cm
On Video CDs
Audio
CDs
Audio
This DVD supports Video CDs equipped with the PBC
(Version 2.0) function. (PBC is the abbreviation of
Playback Control.) You can enjoy two playback
variations depending on types of discs.
8 cm
(CD
single)
The following discs are also available.
CD-R/CD-RW discs of CD-DA, Video CD, MP3, WMA
or JPEG format
Kodak Picture CD and FUJICOLOR CD format
Some of these discs may be incompatible.
• Video CD not equipped with PBC function
(Version 1.1)
Sound and movie can be played on this DVD in the
same way as an audio CD.
• Video CD equipped with PBC function
(Version 2.0)
In addition to operation of a Video CD not equipped
with the PBC function, you can enjoy playback of
interactive software with search function by using the
menu displayed on the TV screen (Menu Playback).
Some of the functions described in this owner’s
manual may not work with some discs.
• You cannot play discs other than those listed above.
• You cannot play discs of DVD-RAM, DVD-ROM,
Photo CD, etc., or non standardized discs even if they
may be labeled as above.
• Some CD-R/RWs can not be played back depending
on the recording conditions.
• This unit uses the NTSC color system, and cannot
play DVD video discs recorded in any other color
system (PAL, SECAM, etc.).
8
5K70101B [E] (P08-12)
8
20/4/04, 15:51
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Advanced playback
Introduction
Zooming ......................................................... 31
Locating desired scene .................................. 31
Repeat playback ............................................ 32
A-B Repeat playback ..................................... 32
Program playback .......................................... 33
Random playback .......................................... 33
Changing angles ............................................ 34
Title selection ................................................. 34
DVD menu...................................................... 34
Changing soundtrack language ..................... 35
Subtitles ......................................................... 35
Karaoke playback........................................... 36
Disc status...................................................... 36
To turn off the PBC ........................................ 36
MP3/WMA/JPEG CD operation ..................... 37
IMPORTANT SAFEGUARDS............................2
Precautions .......................................................6
Notes on discs...................................................7
Contents ............................................................9
Identification of controls ..................................10
Connections
Antenna connections.......................................13
Cable TV connections .....................................14
Connecting to optional equipment...................15
Basic setup
Starting setup ..................................................18
Setting the language .......................................19
TV operation
Function setup
TV operation....................................................20
Closed captions...............................................22
To memorize channels ....................................23
Setting the V-Chip ...........................................24
Picture control adjustment...............................26
Adjusting the picture preference .....................26
Sound control adjustment ...............................27
Stereo and Second Audio Program (SAP) ......27
Customizing the function settings .................. 40
Temporary disabling of rating level
by DVD disc ................................................... 43
Others
Language code list ......................................... 44
Reception disturbances.................................. 45
Troubleshooting ............................................. 46
Specifications ................................................. 48
Limited warranty............................................. 49
Basic playback
Playing a disc ..................................................28
9
5K70101B [E] (P08-12)
9
20/4/04, 15:51
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Identification of controls
See the page in
for details.
Front
POWER indicator 20
AUDIO (L/R)/VIDEO IN
jacks (LINE IN 2)
15
Disc tray
28
STOP( ) button
POWER button 18
28
PHONES jack 21
) buttons 30
SKIP (
PLAY ( ) button 28
CHANNEL ( / ) buttons
/
Remote sensor
12
OPEN/CLOSE ( ) button
28
VOLUME ( / ) buttons 20
21
Rear
AUDIO (L/R)/VIDEO IN jacks (LINE IN 1)
15
COAXIAL DIGITAL AUDIO OUT jack
16
RF IN jack
13
AC power cord
10
5K70101B [E] (P08-12)
10
20/4/04, 15:51
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote control
The instructions in this manual describe the function on the remote control. See the page in
for details.
RECALL
TV/DVD
POWER
INPUT SELECT
GAME
RECALL button 21
POWER button 18
TV/DVD button 28
1
4
2
5
8
3
6
INPUT SELECT button
15
Direct channel selection
buttons (0-9)
20
Numbered buttons (0-9) 24
GAME button
15
OPEN/CLOSE
MUTE
7
SLEEP
9
OPEN/CLOSE button 28
MUTE button
CLOSED
CAPTION
SLEEP button 21
21
CLOSED CAPTION button 22
ANGLE button
0
TOP MENU button 34
TOP MENU
SUBTITLE
AUDIO
ANGLE
34
ZOOM button 31
CH RTN button
SUBTITLE button 35
SETUP/MENU DVD MENU
CANCEL ZOOM/CH RTN
SETUP button 40
21
MENU button
19
AUDIO button 27
*DVD MENU button 34
CH +
CANCEL button 18
Direction buttons 18
(
/
/
-
/
)
VOL –
VOL +
CH +/
VOL +/
button 21
button
-
20
RETURN
ENTER
CH –
ENTER button 18
RETURN button
40
PLAY button 28
REV button
FWD button 30
REV
PLAY
STOP
FWD
SKIP
PLAY MODE
JUMP
30
SKIP buttons 30
PLAY MODE button 32
JUMP button 31
SKIP
PAUSE button 29
SLOW
PAUSE
SLOW
REPEAT A–B
STOP button 28
SLOW buttons 30
REPEAT A-B button 32
*DVD MENU button
Use the DVD MENU button to
display the menu included on
many DVD video discs.
To operate a menu, follow the
34
instructions in “DVD menu.”
11
5K70101B [E] (P08-12)
11
20/4/04, 15:51
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Inserting batteries
Slide the battery compartment
cover in the direction of the
arrow.
Install two “R03/AAA” batteries
(supplied), paying attention to
the polarity diagram in the
battery compartment.
Replace the compartment
cover.
1
2
3
Operation
• Aim the remote control at the remote sensor and press control buttons to operate.
• Operate the remote control within 30° angle on either side of the remote sensor, up to a distance of approx. 5
meters.
Approx. 5 meters
The precautions below should be followed when using batteries in this device:
1. Use only the size and type of batteries specified.
2. Be sure to follow the correct polarity when installing the batteries as indicated in the battery compartment.
Reversed batteries may cause damage to the device.
3. Do not mix different types of batteries together (e.g. Alkaline and Carbon-zinc) or old batteries with fresh ones.
4. If the device is not to be used for a long period of time, remove the batteries to prevent damage or injury from
possible battery leakage.
5. Do not try to recharge batteries not intended to be recharged; they can overheat and rupture (follow battery
manufacturer’s directions).
12
5K70101B [E] (P08-12)
12
20/4/04, 15:51
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections
Antenna connections
If you are using an indoor or outdoor antenna, follow the instructions below that correspond to your antenna system. If
you are using a cable TV service (CABLE), see page 14 for Cable TV connections.
Combination VHF/UHF antenna (Single 75 ohm cable or 300 ohm twin-lead wire)
Connect the 75 ohm cable from the combination
VHF/UHF antenna to the antenna jack.
Antenna
jack
Antenna
jack
If your combination VHF/UHF antenna has a 300
ohm twin-lead wire, the use of the 300-75 ohm
matching transformer may be necessary.
75 ohm coaxial cable
(not supplied)
300-75 ohm matching
transformer (supplied)
Combination VHF/UHF antenna (Separate VHF and UHF 300 ohm twin-lead wires)
Connect the UHF 300 ohm twin-lead wire to the
Antenna
300-75 ohm matching
transformer (supplied)
combiner (not supplied). Connect the VHF 300
ohm twin-lead wire to the 300-75 ohm matching
transformer.Attachthetransformertothecombiner,
then attach the combiner to the antenna jack.
jack
Combiner
(not supplied)
UHF 300 ohm
twin-lead wire
(not supplied)
VHF 300 ohm
twin-lead wire
(not supplied)
Separate VHF/UHF antennas (75 ohm VHF cable and 300 ohm UHF twin-lead wires)
Connect the VHF 75 ohm cable and UHF 300 ohm
twin-lead wire to the combiner (not supplied).
Attach the combiner to the antenna jack.
Antenna
jack
VHF 75 ohm
(not supplied)
Combiner
(not supplied)
UHF 300 ohm
twin-lead wire
(not supplied)
13
5K70101B [E] (P13-23)
13
20/4/04, 15:52
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections
Cable TV connections
This TV/DVD has an extended tuning range and can tune most cable channels without using a Cable TV converter box.
Some cable companies offer “premium pay channels” in which the signal is scrambled. Descrambling these signals for
normal viewing requires the use of a descrambler device which is generally provided by the cable company.
For subscribers to basic cable TV service
Antenna
jack
For basic cable service not requiring a converter/descrambler
box, connect the Cable TV 75 ohm coaxial cable directly to the
Antenna jack on the back of the TV/DVD.
75 ohm
coaxial cable
For subscribers to scrambled cable TV service
If you subscribe to a cable TV service which requires the use of a converter/descrambler box, connect the
incoming 75 ohm coaxial cable to the converter/descrambler box. Using another 75 ohm coaxial cable, connect
the output jack of the converter/descrambler box to the antenna jack on the TV/DVD. Follow the connections
shown below. Set the TV/DVD to the output channel of the converter/descrambler box (usually channel 3 or 4)
and use the converter/descrambler box to select channels.
Incoming
75 ohm
Cable TV
Antenna
jack
75 ohm cable to
TV/DVD
Converter/
descrambler
For subscribers to unscrambled basic cable TV service with scrambled
premium channels
If you subscribe to a cable TV service in which basic channels are unscrambled and premium channels require the
use of a converter/descrambler box, you may wish to use a signal splitter and an A/B Switch box (available from the
cable company or an electronics supply store). Follow the connections shown below. With the switch in the “B”
position, you can directly tune any nonscrambled channels on your TV/DVD. With the switch in the “A” position, tune
your TV/DVD to the output of the converter/descrambler box (usually channel 3 or 4) and use the converter/
descrambler box to tune scrambled channels.
Converter/
descrambler
Incoming
75 ohm
Antenna
jack
75 ohm cable
to TV/DVD
Cable TV
A
A/B switch
Splitter
B
14
5K70101B [E] (P13-23)
14
20/4/04, 15:52
Download from Www.Somanuals.com. All Manuals Search And Download.
INPUT SELECT
GAME
Connecting to optional equipment
You can enjoy VCR, camcorder or TV game with connection to external
input. To select the external input, press INPUT SELECT and select
“LINE1” or “LINE2” mode.
Using the audio/video inputs
Press INPUT SELECT repeatedly to select the desired mode.
“LINE1”, “LINE2” or TV channel will display on the screen for 4 seconds.
TV Channel
LINE 1
(Back)
LINE 2
(Front)
Note: In the DVD mode this key will not operate.
To connect the TV/DVD to a VCR
Press the INPUT SELECT to select the desired mode to use the TV as a monitor.
Operate your VCR as usual.
VCR
Rear of TV/DVD
: Signal flow
VIDEO IN
AUDIO IN (L)
AUDIO IN (R)
To Audio/Video OUT
Audio/Video cable
(not supplied)
To connect the TV/DVD to a camcorder
To playback from the camcorder, connect the camcorder to the TV/DVD as shown.
Front of TV/DVD
Camcorder
: Signal flow
VIDEO IN
To Audio/Video OUT
AUDIO IN (R)
AUDIO IN (L)
Audio/Video cable (not supplied)
To connect the TV/DVD to a TV Game
You can enjoy playing a TV game on the screen by adjusting to suitable brightness for your eyes.
1. Connect a TV Game to the TV/DVD.
2. Press GAME. The GAME mode screen appears.
Front of TV/DVD
• This TV/DVD has the GAME mode function (see page 21).
VIDEO IN
: Signal flow
To Audio/Video OUT
AUDIO IN (R)
AUDIO IN (L)
Audio/Video cable (not supplied)
Notes:
• You can also change the TV screen to LINE2 by pressing the CH +/– buttons.
• The TV/DVD can also be used as a display device for many video games. However, due to the wide variety of different types
of signal generated by these devices and subsequent hook-up variations required, they have not all been included in the
suggested connection diagrams. You'll need to consult each component's Owner's Manual for additional information.
15
5K70101B [E] (P13-23)
15
20/4/04, 15:52
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections
Connecting to optional equipment (Continued)
This section uses the following reference mark.
You can enjoy high quality dynamic sounds by connecting the
TV/DVD to optional audio equipment.
*
: Front speaker
: Rear speaker
: Sub woofer
: Center speaker
: Signal flow
Connecting to an amplifier equipped with a Dolby Digital decoder
Dolby Digital
Dolby Digital is the surround sound technology used in theaters showing the latest movies, and is now available to repro-
duce this realistic effect in the home. You can enjoy motion picture and live concert DVD video discs with this dynamic
realistic sound by connecting the TV/DVD to a 6 channel amplifier equipped with a Dolby Digital decoder or Dolby Digital
processor. If you have a Dolby Surround Pro Logic decoder, you will obtain the full benefit of Pro Logic from the same DVD
movies that provide full 5.1-channel Dolby Digital soundtracks, as well as from titles with the Dolby Surround mark.
Amplifier equipped with a
Dolby Digital decoder
Manufactured under license
from Dolby Laboratories.
“Dolby”, “Pro Logic”, and the
double-D symbol are trade-
marks of Dolby Laboratories.
To COAXIAL
type digital
audio input
75 Ω coaxial cable (not supplied)
Connecting to an amplifier equipped with Dolby Surround Pro Logic
Dolby Surround Pro Logic
You can enjoy the dynamic realistic sound of Dolby Surround Pro Logic by connecting an amplifier and speaker system (right
and left front speakers, a center speaker, and one or two rear speakers).
3 With an amplifier equipped with Dolby Digital
Connect the equipment the same way as described in “Connecting to an amplifier equipped with a Dolby Digital decoder.”
Refer to that amplifier’s owner’s manual and set the amplifier so you can enjoy Dolby Surround Pro Logic sound.
3 With an amplifier not equipped with Dolby Digital
Connect the equipment as follows.
• This connection is only suitable for Video CDs and Audio CDs.
*
Amplifier equipped with
Dolby Surround Pro Logic
Connect one or two rear speak-
*
To COAXIAL
type digital
audio input
ers. The output sound from the
rear speakers will be monaural
even if you connect two rear
speakers.
75 Ω coaxial cable (not supplied)
Connecting to an amplifier equipped with a DTS decoder
Digital Theater Systems (DTS)
DTS is a high quality surround technology used in theaters and now available for home use, on DVD video discs or audio CDs.
If you have a DTS decoder or processor, you can obtain the full benefit of 5.1 channel DTS encoded sound tracks on DVD
video discs or audio CDs.
Amplifier equipped with
a DTS decoder
“DTS” and “DTS Digital Sur-
round” are trademarks of Dig-
ital Theater Systems, Inc.
To COAXIAL
type digital
audio input
75 Ω coaxial cable (not supplied)
16
5K70101B [E] (P13-23)
16
20/4/04, 15:52
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to an amplifier equipped with a MPEG audio decoder
MPEG2 sound
You can enjoy motion picture and live concert DVD video discs with dynamic realistic sound by connecting an amplifier
equipped with an MPEG2 audio decoder or MPEG2 audio processor.
Amplifier equipped with an
MPEG2 audio decoder
To COAXIAL
type digital
audio input
75 Ω coaxial cable (not supplied)
Connecting to an amplifier equipped with a digital audio input
2 channel digital stereo
You can enjoy the dynamic sound of 2 channel digital stereo by connecting an amplifier equipped with a digital audio input
and speaker system (right and left front speakers).
Amplifier equipped with a
Digital audio input
To COAXIAL
type digital
audio input
75 Ω coaxial cable (not supplied)
Notes:
• DO NOT connect the COAXIAL DIGITAL AUDIO OUT jack of the TV/DVD to the AC-3 RF input of a Dolby Digital Receiver.
This input on your A/V Receiver is reserved for Laserdisc use only and is incompatible with the COAXIAL DIGITAL AUDIO
OUT jack of the TV/DVD.
• Connect the COAXIAL DIGITAL AUDIO OUT jack of the TV/DVD to the “COAXIAL” input of a Receiver or Processor.
• Refer to the owner’s manual of the connected equipment as well.
• When you connect the TV/DVD to other equipment, be sure to turn off the power and unplug all of the equipment from the
wall outlet before making any connections.
• The output sound of the TV/DVD has a wide dynamic range. Be sure to adjust the receiver’s volume to a moderate
listening level. Otherwise, the speakers may be damaged by a sudden high volume sound.
• Turn off the amplifier before you connect or disconnect the TV/DVD’s power cord. If you leave the amplifier power on, the
speakers may be damaged.
17
5K70101B [E] (P13-23)
17
20/4/04, 15:52
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic setup
POWER
Starting setup
The STARTING SETUP function makes installing your TV/DVD easily. It leads
you the Language selection, TV/CABLE selection and auto channel memory
automatically.
CANCEL
/
IMPORTANT: Make sure that the antenna or cable TV system connection
is made!
ENTER
Starting setup
Now the “AUTO CH MEMORY” starts.
Press POWER.
After the starting setup is completed, the TV
channel appears on the screen.
The starting setup function begins and the
Language setup menu appears on the screen.
4
1
Press
or
to select your desired
language, then press ENTER.
Note:
If you press the CANCEL button in the process of
“AUTO CH MEMORY” you can do starting set up
function again.
POWER
ENTER
LANGUAGE/IDIOMA/LANGUE
ENGLISH
ESPAÑOL
FRANCAIS
CH +
CH –
AUTO CH MEMORY
STOP : CANCEL
<
/
/ ENTER>
Press
or
to select “TV” or “CABLE”, then
press ENTER.
2
3
ENTER
Note:
CH +
CH –
CHANNEL PLAN
The starting setup function will work only when you press the
POWER button for the first time.
TV
CABLE
<
/
/ ENTER>
Press
or
to select “START”, then press
ENTER.
If you select “CANCEL” and press ENTER, the
STARTING SETUP stops and changes to the TV
screen.
ENTER
CH +
AUTO SETUP
START
CANCEL
CH –
<
/
/ ENTER>
18
5K70101B [E] (P13-23)
18
20/4/04, 15:52
Download from Www.Somanuals.com. All Manuals Search And Download.
POWER
MENU
Setting the language
This TV/DVD can display the on screen language in English, Spanish or French.
Select the language you prefer first, then proceed with the other menu
options.
/
/
/
ENTER
Setting the language
Press MENU, then press
option.
or
to select
1
SETUP/MENU
LANGUAGE/IDIOMA/LANGUE
VOL –
VOL +
ENGLISH
ESPAÑOL
FRANCAIS
/MENU
Press
or
to select the desired language:
English (ENGLISH), Spanish (ESPAÑOL) or
French (FRANCAIS), then press ENTER.
2
ENTER
CH +
LANGUAGE/IDIOMA/LANGUE
ENGLISH
ESPAÑOL
CH –
FRANCAIS
/
/ ENTER/MENU
Press MENU repeatedly until the menu screen
is cleared.
3
SETUP/MENU
Notes:
• If the unit does not operate properly, or No key operation
(by the unit and/or the remote control): Static electricity,
etc., may affect the player's operation. Disconnect the AC
power cord once, then connect it again.
• The TV section has its own menu and also DVD section has
its own menu 40
.
19
5K70101B [E] (P13-23)
19
20/4/04, 15:52
Download from Www.Somanuals.com. All Manuals Search And Download.
TV operation
POWER
0–9
TV operation
VOL +/–
TV operation
To turn on the TV/DVD, press POWER.
The Power indicator will light.
Press direct channel selection (0–9) to select
the channel.
4
1
2
POWER
TV mode direct channel selection
When the TV/CABLE selection is in the TV
position, all channels can be instantly selected by
using two buttons. (for example, to select channel
2, press “0”, then “2”. If
Adjust the volume level by pressing VOL + or –.
The volume level will be indicated on the
screen by green bars. As the volume level
increases, so do the number of bars. If the
volume decreases, the number of green bars
also decreases.
you press only “2”,
channel selection will
CH 12
be delayed for a few
seconds.) For channels
10 and above, press
the 2 digits in order.
CABLE mode direct channel selection
When the TV/CABLE selection is in the CABLE
position, channels can be selected as follows:
TO SELECT CABLE TV CHANNELS:
VOL –
VOL +
1-9:
Press “0” twice, then 1-9 as needed.
Example, to select channel 2, press
“002”.
VOLUME
32
10-12:
13-99:
Press “0”, then the remaining 2 digits.
Example, to select channel 12, press
“012”.
Press the 2 digits in order. Example, to
select channel 36, press “36”.
Set the TV/CABLE selection to the appropriate
position. (See page 23.)
3
100-125: Press the 3 digits in order. Example, to
select channel 120, press “120”.
NOTE FOR CHANNELS 1-12:
If only 1 or 2 buttons are pressed, the corresponding
channel will be selected in 2 seconds.
TV
- VHF/UHF channels
CABLE - Cable TV channels
CATV
VHF
2-13
TV
VHF
2-13
UHF
14-69
STD/HRC/IRC
14-36
(A) (W)
37-59
(AA) (WW)
60-85
(AAA) (ZZZ)
86-94
(86) (94)
95-99
(A-5) (A-1)
100-125
(100) (125)
01
(5A)
Notes:
• If a channel with no broadcast is selected, the sound will auto-
matically be muted.
• If a station being viewed stops broadcasting, the TV will auto-
matically shut itself off after 15 minutes.
20
5K70101B [E] (P13-23)
20
20/4/04, 15:52
Download from Www.Somanuals.com. All Manuals Search And Download.
RECALL
GAME
SLEEP
MUTE
CH RTN
CH +/–
VOL +/–
■ SLEEP
■ CHANNEL UP/DOWN
To set the TV/DVD to turn off after a preset amount of
time, press SLEEP on the remote control. The clock
will count down 10 minutes for each press of SLEEP
(120, 110, ...10, 0). After the sleep time is programmed,
the display will appear briefly every ten minutes to
remind you that the sleep timer is operating. To confirm
the sleep timer setting, press SLEEP and the remain-
ing time will be displayed for a few seconds. To cancel
the sleep timer, press SLEEP repeatedly until the
display turns to 0.
Press and release CH + or –. The channel automati-
cally stops at the next channel set into memory.
For proper operation, before selecting channels, they
should be set into the memory. See page 23 “To
memorize channels”.
CH +
CH –
SLEEP
120
■ RECALL
Press RECALL to display the current informations on the
screen. Press RECALL again to clear the display.
• Channel number or external input mode
• Stereo or SAP (Second Audio Program) audio status
• Audio output status
■ GAME MODE
After connecting a TV Game to the unit, press GAME.
The TV screen changes to the Game mode.
• The Game mode screen is adjusted to the suitable
brightness for your eyes.
STEREO SAP
CH 012
RECALL
• Game timer function: After one hour the Game timer
display will appear every 30 minutes for approx. 5
seconds showing how long the time has passed up
to 4 hours.
SEL. STEREO
• If GAME is pressed during standby mode, the unit
turns on automatically and the Game mode screen
appears on the screen.
■ CH RETURN
This button allows you to go back to the last channel
selected by pressing CH RTN. Press CH RTN again to
return to the last channel you were watching.
ZOOM/CH RTN
■ HEADPHONES
Insert a stereo headphones (not supplied) with a 1/8”
mini plug into the PHONES jack on the front panel. If
you connect headphones, the sound from TV speakers
is muted.
■ MUTE
Press MUTE to switch off the sound. The TV/DVD’s
sound will be silenced and “MUTE” will briefly appear on
the screen. The sound can be switched back on by
pressing this button again or one of VOL +/–.
MUTE
VOL –
VOL +
21
5K70101B [E] (P13-23)
21
20/4/04, 15:52
Download from Www.Somanuals.com. All Manuals Search And Download.
TV operation
Closed captions
WHAT IS CLOSED CAPTIONING?
CLOSED
CAPTION
This television has the capability to decode and display closed captioned
television programs. Closed captioning will display text on the screen for
hearing impaired viewers or it will translate and display text in another
language.
Closed captions
Captions: This closed caption mode will display text on the screen in English or another language (depending
on the setting of the closed captions CH 1/2).
Generally, closed captions in English are transmitted on captions channel 1 and closed captions in other lan-
guages are transmitted on captions channel 2.
Text: The text closed caption mode will usually fill the screen with a programming schedule or other information.
After selecting a closed caption mode, it will stay in effect until it is changed, even if the channel is changed.
If the captions signal is lost due to a commercial or a break in the signal, the captions will reappear when the
signal is received again. If the channels are changed, the captions will be delayed approximately 10 seconds.
The captions will appear in places on the screen where they will least interfere with the picture, usually on the
bottom of the screen. News programs will usually show three-line closed captions which scroll onto the screen.
Most other shows provide two or three lined captions placed near the character who is speaking so the viewer
can follow the dialogue. Words in italics or underlined describe titles, words in foreign languages or words
requiring emphasis. Words that are sung usually appear enclosed by musical notes.
For television programs broadcasting with closed captions, look in your TV guide for the closed captions symbol
(CC).
TO VIEW CLOSED CAPTIONS
Press CLOSED CAPTION to switch between normal TV and the two closed
caption modes (captions and full screen text). Closed captioning will display text
on the screen for hearing impaired viewers.
CLOSED
CAPTION
Notes:
• When selecting closed captions, the captioning will be delayed approximately 10 seconds.
• If no caption signal is received, no captions will appear, but the television will remain in the caption mode.
• Misspellings or unusual characters may occasionally appear during closed captioning. This is normal with closed captioning,
especially with live programs. This is because during live programs, captions are also entered live. These transmissions do not
allow time for editing.
• When captions are being displayed, on-screen displays, such as volume and mute may not be seen or may interfere with closed
captions.
• Some cable systems and copy protection systems may interfere with the closed captioned signal.
• If using an indoor antenna or if TV reception is very poor, the closed caption decoder may not appear or may appear with
strange characters or misspelled words. In this case, adjust the antenna for better reception or use an outdoor antenna.
22
5K70101B [E] (P13-23)
22
20/4/04, 15:52
Download from Www.Somanuals.com. All Manuals Search And Download.
To memorize channels
0–9
This TV/DVD is equipped with a channel memory feature which allows
channels to skip up or down to the next channel set into memory, skipping over
unwanted channels. Before selecting channels, they must be programmed into
the TV/DVD’s memory. In addition to normal VHF and UHF channels, this TV/
DVD can receive up to 113 Cable TV channels. To use this TV/DVD with an
antenna, set the TV/CABLE selection to the TV position. When shipped from
the factory, this selection is in the CABLE position.
MENU
/
/
/
TV/CABLE selection
Automatic memory tuning
Press MENU in the TV mode, then press
or
Press
or
to select the “AUTO CH MEMORY”,
to select
SETUP/MENU
option.
then press
.
1
The TV will begin memorizing all the channels
available in your area.
CH +
VOL +
CH –
VOL –
VOL +
Press
or
to select “TV/CABLE”.
2
3
CH +
To ADD/DELETE channels
CH –
Press
press
or
to select “ADD/DELETE”, then
.
1
CH +
CH –
Press
or
to select “TV” or “CABLE”.
VOL +
TV - VHF/UHF channels
CABLE - Cable TV channels
VOL –
VOL +
Select the desired channel to be added or
deleted using Direct channel selection (0–9) or
CH +/–.
2
3
1
4
7
2
5
8
0
3
6
9
CH +
CH –
Press MENU repeatedly until the menu screen is
cleared.
SETUP/MENU
4
Press
or
to select “ADD” or “DELETE”,
whichever function you want to perform.
Cable TV chart
The chart below is typical of many cable system channel
allocations.
ADD
CH 001
VOL –
VOL +
0-9 /
/
/
/
/
MENU
23
5K70101B [E] (P13-23)
23
20/4/04, 15:52
Download from Www.Somanuals.com. All Manuals Search And Download.
TV operation
Setting the V-Chip
0–9
An age limitation can be set to forbid children to watch programs according to
“TV RATING” and “MOVIE RATING” level set. To use the V-Chip function,
you must register a password.
MENU
CANCEL
/
/
/
Notes:
ENTER
• If you forget the password, you cannot set the V-Chip.
• To avoid forgetting the password, write it down and keep in
the safe place.
To register password
To change password
In the V-CHIP menu, press
“CHANGE PASSWORD”, then press
or
to select
Press MENU, then press
option.
or
to select
.
1
1
SETUP/MENU
CH +
V-CHIP SET
V-CHIP
V-CHIP SET
OFF
VOL +
VOL –
VOL +
NEW
CHANGE PASSWORD
PASSWORD : – – – –
CH –
/
/
/
/ MENU
/
/
/ MENU
Press
CH +
or
to select “PASSWORD”.
Enter the new password using Number buttons
(0–9), then press ENTER.
2
3
2
3
4
ENTER
V-CHIP SET
1
4
7
2
5
8
0
3
6
9
CH –
NEW
PASSWORD : – – – –
CHANGE PASSWORD
NEW
0–9/ENTER/CANCEL/MENU
PASSWORD
: – – – –
Enter the password (4 digits) using Number
buttons (0–9), then press ENTER.
• If you put a wrong number, press CANCEL.
0-9/ENTER/CANCEL/MENU
Enter the same password again using Number
buttons (0–9) for safety, then press ENTER.
1
4
7
2
5
8
0
3
6
9
V-CHIP SET
ENTER
1
4
7
2
5
8
0
3
6
9
NEW
CHANGE PASSWORD
PASSWORD
:
CONFIRM
PASSWORD
:
0–9/ENTER/CANCEL/MENU
CANCEL
ENTER
0-9/ENTER/CANCEL/MENU
“
” appears instead of the number.
Enter the same password again for the safety,
then press ENTER.
Now the password was registered and V-Chip
setting menu will appear on the display.
Press MENU repeatedly until the menu screen
is cleared.
4
SETUP/MENU
ENTER
V-CHIP SET
CONFIRM
PASSWORD
:
0–9/ENTER/CANCEL/MENU
24
5K70101B [E] (P24-27)
24
20/4/04, 15:53
Download from Www.Somanuals.com. All Manuals Search And Download.
RECALL
MENU
/
/
/
ENTER
To set the V-Chip
Press
or
to select desired rating.
In the V-CHIP menu, press
or
to select
After setting, press ENTER.
“V-CHIP SET”, then press
.
4
1
VOL –
VOL +
CH +
V-CHIP SET
TV RATING
MOVIE RATING
TV-Y
PG-13
V-CHIP
V-CHIP SET
CHANGE PASSWORD
OFF
ENTER
VOL +
CH –
/
/
/
/ ENTER/MENU
/
/
/ MENU
OFF : MOVIE RATING is not set
G
PG
: All ages
: Parental guidance
Press
press or
After setting, press ENTER.
or
to select “TV RATING”, then
to display the desired setting.
2
3
PG-13 : Parental guidance
less than 13 years old
OFF : TV RATING is not set
TV-Y : All children
R
: Under 17 years old
Parental guidance suggested
NC-17 : 17 years old and above
TV-Y7 : 7 years old and above
TV-G : General audience
TV-PG : Parental guidance
TV-14 : 14 years old and above
TV-MA: 17 years old and above
X
: Adult only
Press
or to select “V-CHIP”.
5
6
CH +
CH –
When you select TV-
Y7, TV-PG, TV-14 or
TV-MA, press
RECALL to show the
contained rating.
Press or
V-CHIP
V-CHIP SET
CHANGE PASSWORD
OFF
V-CHIP SET
TV RATING
MOVIE RATING
TV-Y
OFF
/
/
/
/ MENU
/
/
to select the desired
item you want.
/
/
/
/ ENTER/MENU
Press
or
to display “ON”.
Now your settings were set into the memory.
CH +
ENTER
RECALL
VOL –
VOL +
VOL –
VOL +
V-CHIP
V-CHIP SET
CHANGE PASSWORD
ON
CH –
Press
or
to select “MOVIE RATING”.
/
/
/
/ MENU
Press MENU repeatedly until the menu screen is
cleared.
CH +
CH –
7
V-CHIP SET
TV-Y
OFF
TV RATING
MOVIE RATING
SETUP/MENU
To use after the TV is protected
When the program applied to the V-Chip setting is received,
/
/
/
/ ENTER/MENU
enter the password, then press ENTER. Protection can be
canceled.
Note:
The V-Chip function is activated only on programs that have
the rating signal.
25
5K70101B [E] (P24-27)
25
20/4/04, 15:53
Download from Www.Somanuals.com. All Manuals Search And Download.
TV operation
Picture control adjustment/
Adjusting the picture preference
MENU
CANCEL
Picture controls are factory preset but you can adjust them individually as follows:
And also you can select four picture modes—Standard, Sports, Movie, and
Memory—as described in the following table:
/
/
/
ENTER
Picture control adjustment
Adjusting the picture preference
Press MENU, then press
option.
or
to select
Press MENU, then press
option.
or
to select
1
1
2
SETUP/MENU
SETUP/MENU
VOL –
VOL +
VOL –
VOL +
Press
.
or
to select “PICTURE”, then press
Press
or
to select “PICTURE
PREFERENCE”, then press
.
2
CH +
VOL +
CH +
VOL +
CH –
CH –
Press
or
to select the item you want to
adjust, then press
or
to adjust the setting.
3
Press
or
to select the desired picture
mode, then press ENTER.
CH +
3
BRIGHTNESS
CONTRAST
COLOR
TINT
SHARPNESS
0
+32
0
0
0
VOL –
VOL +
ENTER
CH –
CH +
PICTURE PREFERENCE
STANDARD
SPORTS
MOVIE
/
/
/
/ CANCEL / MENU
CH –
MEMORY
Selection
Pressing
/
/ ENTER / MENU
BRIGHTNESS
CONTRAST
COLOR
TINT
SHARPNESS
darker
lower
paler
reddish
softer
lighter
higher
deeper
greenish
sharper
Mode
Picture quality
STANDARD Standard picture quality (factory-set)
SPORTS
MOVIE
Bright and dynamic picture (factory-set)
Movie-like picture setting (factory-set)
Your personal preferences (set by you;
see “Picture control adjustment” as left)
Note:
MEMORY
The CONTRAST default setting is set to maximum
(+32) at the factory.
After your desired setting press MENU
repeatedly until the menu screen is cleared.
After your desired setting press MENU
repeatedly until the menu screen is cleared.
4
4
SETUP/MENU
SETUP/MENU
Note:
3 To return all adjustments to the factory preset levels
You can not select “PICTURE PREFERENCE” in the Game
mode.
26 Press CANCEL while making picture adjustments.
5K70101B [E] (P24-27)
26
20/4/04, 15:53
Download from Www.Somanuals.com. All Manuals Search And Download.
Sound control adjustment/
AUDIO
MENU
Stereo and Second Audio Program (SAP)
CANCEL
Sound controls are factory preset but you can adjust them individually as follows:
The TV/DVD is equipped with a feature known as multi-channel TV sound or
MTS. MTS broadcasts greatly enhance TV viewing by bringing you programs
with high fidelity stereo sound.
/
/
/
ENTER
MTS also provides an extra channel called the Second Audio Program or SAP
which broadcasters can use to transmit a second language for bilingual transmis-
sion or for other purposes.
Sound control adjustment
Listening to stereo sound
When the TV is turned on or a channel selection is
made, make certain the “STEREO” appears on the
screen. This means that Stereo broadcasting is avail-
able. You can enjoy stereo sound from the left and
right speakers.
Press MENU, then press
option.
or
to select
1
2
SETUP/MENU
VOL –
VOL +
• When mono broadcasting is received, no indication is
displayed.
• If the broadcast signal is not strong enough or clear
stereo sound is not available, press AUDIO to change
to mono sound. The noise should be eliminated. Press
it again to return to the stereo sound.
Press
.
or
to select “AUDIO”, then press
CH +
AUDIO
VOL +
STEREO
CH 013
CH –
Press
adjust, then press
or
to select the item you want to
Listening to SAP (Second Audio Program)
or
to adjust the setting.
3
When the TV is turned on or a channel selection is
made, make certain the SAP appears on the screen.
This means that the Second Audio Program
broadcasting is available.
CH +
VOL –
VOL +
CH –
BASS:
Press
STEREO SAP
CH 013
or
to adjust the bass sound.
TREBLE:
Press
or
to adjust the treble sound.
BALANCE:
Press
both speakers.
or
to obtain an equal sound level from
To select desired sound
SURROUND:
Press
or
to select “ON” or “OFF”.
Press AUDIO to select the desired sound.
ON: The dynamic presence and sound created of-
fers a thoroughly enjoyable listening experience.
OFF: Normal sound.
AUDIO
SEL. STEREO
STABLE SOUND:
Press
or
to select “ON” or “OFF”.
ON: The Stable Sound feature limits the highest
volume level to prevent extreme changes in
volume when the signal source is changed.
OFF: Normal sound.
MONO + SAP BROADCASTING
MONO SOUND
(MAIN)
SAP SOUND
After your desired setting press MENU
repeatedly until the menu screen is cleared.
STEREO+SAP BROADCASTING
4
STEREO SOUND
SAP SOUND
SETUP/MENU
(MAIN)
MONO SOUND
(MAIN)
3 To return BASS/TREBLE/BALANCE control
adjustments to the factory preset levels
Press CANCEL while making sound adjustments.
27
5K70101B [E] (P24-27)
27
20/4/04, 15:53
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic playback
Playing a disc
This section shows you the basics on how to play a disc.
CAUTION
Keep your fingers well clear of the disc tray as it is closing.
Neglecting to do so may cause serious personal injury.
1 3,5 5 6
4
DVD
VCD
CD
Basic playback
Preparations:
• Insert the AC cord plug into a standard 120V 60Hz polarized AC outlet. If the AC cord plug is plugged in for the first time,
you need to set “Starting setup”
.
18
• When connecting to other equipment, turn power off.
Press OPEN/CLOSE or PLAY.
Press POWER on the unit or on the remote control
to turn on the unit.
The Power indicator will light.
• Every time you press POWER, the TV/DVD starts from
TV mode.
• When using an amplifier, switch on the amplifier.
1
5
6
The disc tray closes automatically.
On the TV-screen, “ ” changes to
“Reading” and then playback
commences.
OR
Reading
Press TV/DVD to select DVD mode.
The DVD startup screen will appear on the screen.
“Reading” display will change to “No Disc”. (If DVD
disc has already loaded, playback will start automati-
cally.)
2
• A menu screen will appear on the TV screen, if
the disc has a menu feature.
Press C/D or B/A to select title, then press ENTER.
Title is selected and play commences.
Press STOP to end playback.
3Resuming facility
• The unit records the stopped point,
Press OPEN/CLOSE.
The disc tray opens.
3
depending on the disc. “
”
appears on the screen. Press
PLAY to resume playback (from
the scene point).
• If you press STOP again or unload
the disc (“3” appears on the
screen.), the unit will clear the
stopped point.
Place the disc on the disc tray.
4
3 To start playback in the stop mode
Press PLAY.
With the playback
side down
Note:
• There are two different disc sizes. Place the disc in
the correct guide on the disc tray. If the disc is out of
the guide, it may damage the disc and cause the unit
to malfunction.
If the unit does not operate properly:
Static electricity, etc., may affect the player's operation.
Disconnect theAC power cord once, then connect it again.
• Do not place a disc which is unplayable on the disc tray.
28
5K70101B [E] (P28-32)
28
20/4/04, 15:53
Download from Www.Somanuals.com. All Manuals Search And Download.
To obtain a higher quality picture
TV/DVD
POWER
Occasionally, some picture noise not usually visible during a normal broadcast
may appear on the TV screen while playing a DVD video disc because the high
resolution pictures on these discs include a lot of information. While the amount of
noise depends on the TV you use with this unit, you should generally reduce the
sharpness adjustment on your TV when viewing DVD video discs.
OPEN/CLOSE
DVD VCD
CD
About
The
DVD VCD
CD
icons on the heading bar show the playable discs for the
function described under that heading.
PLAY
STOP
: You can use this function with DVD video discs.
: You can use this function with Video CDs.
: You can use this function with Audio CDs and CD-R/RW CDs.
VCD
PAUSE
CD
To remove the disc
Press OPEN/CLOSE.
To pause playback (still mode)
Press PAUSE during playback.
PAUSE
Remove the disc after the disc tray
opens completely.
To resume normal playback, press
PLAY.
• The sound is muted during still
mode.
To stop playback
Press STOP.
STOP
Be sure to press OPEN/CLOSE to close the disc tray
after you remove the disc.
Notes:
• If a non-compatible disc is loaded, “Incorrect Disc”, “Region Code Error” or “Parental Error” will appear on the TV screen
according to the type of loaded disc. In this case, check your disc again (see pages 8 and 42).
• Some discs may take a minute or so to start playback.
• When you set a single-faced disc label downwards (ie. the wrong way up) and press the OPEN/CLOSE button or the PLAY
button on the unit, “Reading” will appear on the display for 30 seconds and then “Incorrect Disc” will continue to be displayed.
• Some discs may not work the resuming facility.
• Resuming cannot function when you play a PBC-featured Video CD while the PBC is on. To turn off the PBC, see page 36.
• Some playback operations of DVDs may be intentionally fixed by software producers. Since this unit plays DVDs according
to the disc contents the software producers designed, some playback features may not be available. Also refer to the
instructions supplied with the DVDs.
• Do not move the unit during playback. Doing so may damage the disc.
• Use the OPEN/CLOSE button to open and close the disc tray. Do not push the disc tray while it is moving. Doing so may
cause the unit to malfunction.
• Do not push up on the disc tray or put any objects other than discs on the disc tray. Doing so may cause the unit to
malfunction.
• In many instances, a menu screen will appear after playback of a movie is completed. Prolonged display of an on-screen
menu may damage your television set, permanently etching that image onto its screen. To avoid this, be sure to press the
POWER button on your remote control once the movie is completed.
• There may be a slight delay between you pressing the button and the function activating.
29
5K70101B [E] (P28-32)
29
20/4/04, 15:53
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic playback
Playing a disc (continued
)
REV
PLAY
FWD
SKIP
/
PAUSE
SLOW
/
DVD
VCD
CD
Playing in fast reverse or fast forward directions
To resume normal playback
Press PLAY.
Press REV or FWD during playback.
PLAY
FWD
REV
REV: Fast reverse playback
FWD: Fast forward playback
Notes:
Each time you press REW or FWD
• The TV/DVD mutes sound and subtitles during reverse
and forward scan of DVD video discs. However, the TV/
DVD plays sound during fast forward or fast reverse play
of audio CDs.
button, the playback speed changes.
• The playback speed may differ depending on the disc.
DVD
VCD
Playing frame by frame
To resume normal playback
Press PLAY.
Press PAUSE during still playback.
Each time you press PAUSE, the
picture advances one frame.
PAUSE
PLAY
Note:
The sound is muted during frame by frame playback.
DVD
VCD
Playing in slow-motion
To resume normal playback
Press PLAY.
Press SLOW
during playback.
(REVERSE) or
(FORWARD)
PLAY
SLOW
SLOW
Each time you press the button, the
slow-motion speed changes.
Notes:
• The sound is muted during slow-motion playback.
• The Video CD can not play Reverse Slow.
DVD
VCD
CD
Locating a chapter or track
Press SKIP
or
repeatedly to display the chapter or track number you want.
Playback starts from the selected chapter or track.
SKIP
SKIP
To locate succeeding chapters or
Playback starts from the beginning of
tracks.
the current chapter or track.
When you press twice in quick successions,
playback starts from the beginning of
the preceding chapter or track.
Notes:
• A “Prohibition” symbol
may appear at the upper left of the screen. This symbol means either the feature you tried is not
available on the disc, or the TV/DVD can not access the feature at this time. This does not indicate a problem with the TV/DVD.
• The unit is capable of holding a still video image or On screen display image on your television screen indefinitely. If you leave
the still video image or On screen display image displayed on your TV for an extended period of time, you risk permanent
damage to your television screen. Projection televisions are very susceptible.
30
5K70101B [E] (P28-32)
30
20/4/04, 15:53
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced playback
RECALL
0–9
Zooming/Locating desired scene
CANCEL
ZOOM
/
/
/
ENTER
JUMP
DVD
VCD
CD
DVD
VCD
Zooming
Locating desired scene
This unit will allow you to zoom in on the frame image. You
can then make selections by switching the position of the
frame.
Use the title, chapter and time recorded on the disc to locate
the desired point to play back.
To check the title, chapter and time, press RECALL.
Press ZOOM during playback.
Press JUMP during playback or stop mode.
1
1
The centre part of the image will be
zoomed in.
Each press of ZOOM will change the
ZOOM/CH RTN
JUMP
Jump
Time
Title
Chapter
ZOOM 1 (x 1.3), 2 (x 1.5) and
(x 2.0).
3
/Enter/0 9/Cancel/Jump
1
Press
or
to select the “Time”, “Title” or
“Chapter”.
2
3
Jump
Time
Title
Chapter
CH +
CH –
/Enter/0 9/Cancel/Jump
Press
/
/
/
to view a different part of the
frame.
2
Press Numbered buttons (0–9) to change the
number.
You may move the frame from the
center position to UP, DOWN, LEFT
or RIGHT direction.
CH +
VOL –
VOL +
1
4
7
2
5
8
0
3
6
9
CH –
Jump
Time
Title
Chapter
12
/Enter/0 9/Cancel/Jump
In the zoom mode press ZOOM repeatedly to
return to a 1:1 view ( Off).
3
• If you input a wrong number, press
CANCEL.
• Refer to the package supplied with
the disc to check the numbers.
ZOOM/CH RTN
Notes:
Press ENTER. Playback starts.
• You can select the Pause, Slow or Search playback in the zoom
mode.
• Some discs may not respond to zoom feature.
4
• When you change the title,
playback starts from Chapter 1
of the selected title.
ENTER
• Some discs may not work in the
above operation.
Note:
In case of the Video-CD playback with PBC, the JUMP does not
work. To turn off PBC, see page
.
31
5K70101B [E] (P28-32)
31
20/4/04, 15:54
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced playback
Repeat playback/A-B Repeat playback
/
/▼
ENTER
PLAY
PLAY MODE
REPEAT A-B
DVD
VCD
CD
DVD
VCD
CD
Repeat playback
A-B Repeat playback
A-B repeat playback allows you to repeat material between
two selected points.
Press PLAY MODE during playback or stop
mode.
1
2
Press REPEAT A-B during playback.
PLAY MODE
1
The start point is selected.
REPEAT A-B
A
[DVD]
Press B/A or ENTER once or twice to select
“Chapter” or “Title”.
The unit automatically starts repeat
VOL –
VOL +
playback after finishing the current title
or chapter.
ENTER
Press REPEAT A-B again.
2
Repeat
/Enter/Play Mode
Off
The end point is selected. Playback
starts at the point that you selected.
Playback stops at the end point, re-
turns to Point A automatically, then
starts again.
REPEAT A-B
[Audio CD, Video CD]
Press D to select “Repeat”.
Press B/A or ENTER once or twice to select
“Track” or “All”.
A
B
The unit automatically starts repeat
VOL –
VOL +
playback after finishing the current
track.
CH –
ENTER
Play Mode
Repeat
Off
Off
/Enter/Play Mode
To resume normal playback
Press REPEAT A-B again.
• If you set the repeat mode during stop mode,
press PLAY to start Repeat playback.
REPEAT A-B
“
” appears on the screen.
Off
Press PLAY MODE again to make the screen
disappear.
Notes:
• In A-B Repeat mode, subtitles near the A or B locations may
not be displayed.
• You can not set the A-B Repeat for the scenes that include
multiple angles.
3
To resume normal playback
• A-B Repeat playback does not work when Repeat playback is
activated.
• You may not be able to set A-B Repeat, during certain scenes
of the DVD.
• A-B Repeat does not work with an interactive DVD, MP3/WMA/
JPEG CD.
Select Repeat : “Off” in step 2.
Notes:
• Some discs may not work with the repeat operation.
• In case of Video CD with PBC, repeat functions are prohib-
ited during playback.
• A-B Repeat is prohibited when PBC is on.
32
5K70101B [E] (P28-32)
32
20/4/04, 15:54
Download from Www.Somanuals.com. All Manuals Search And Download.
Program playback/Random playback
0–9
You can arrange the playback order of tracks or files on the disc. And also
the unit selects tracks or files at random and playback them. These feature
works for Audio CD, Video CD and MP3/WMA/JPEG CD.
CANCEL
▲/ ▼ /
/
ENTER
PLAY MODE
SKIP7
PLAY
VCD
CD
Program playback
Press
and press ENTER.
/
/
/
to select “Program Playback”
Press PLAY MODE in the stop mode.
4
1
2
PLAY MODE
The programs you selected will start to playback in
the order.
• In case of JPEG file, press SKIP
the program playback.
• To resume normal playback, select Play Mode:
“Off” in step 2.
to continue
Press
/
or
to select Play Mode, then press
or ENTER to select “Program”.
ENTER
CH +
CH –
ENTER
CH +
Play Mode
Repeat
:
:
Program
Off
VOL –
VOL +
VOL –
VOL +
1 9
4
7
8
9
10
11
12
CH –
2
3
3
11
5
6
Clear
Program Playback
/Enter/0 9/Cancel/Play Mode
Press
/
or
/
to select the programming
position. Use Number buttons (0–9) to input the
Track or file numbers.
■ To change the program
1. In the program mode, press C/D/B /A to select the track
number.
2. Press Number buttons (0–9) to select the track number to
be replaced.
■ To clear the program one by one
In the program mode, press C/D/B/A to select the track
number. Then press CANCEL.
3
• To program others, repeat step 3.
• If you input a wrong number, press
CH +
VOL –
VOL +
CANCEL.
CH –
Play Mode
Repeat
:
:
Program
Off
7
8
9
■ To clear all the programs
In the program mode, press C/D/B/A to select “Clear”. Then
press ENTER.
1
4
7
2
5
8
0
3
6
9
1 9
4
5
6
10
11
12
2
3
3
11
Notes:
Clear
Program Playback
/Enter/0 9/Cancel/Play Mode
• In playing back the Video CD with PBC, you can not set
Program playback.
• The program is cancelled when you open the disc tray or
turn the power off.
VCD
CD
Random playback
Press PLAY MODE during playback or stop
mode.
Press PLAY.
1
2
3
PLAY
The Random Playback will start.
PLAY MODE
• If you set “Random” during playback mode,
Random playback will begin after the track that is
currently being played has ended.
• To resume normal playback, select Play Mode:
“Off” in step 2.
Press C/D to select Play Mode, then press
B/A or ENTER to select “Random”.
ENTER
CH +
Play Mode
Repeat
:
:
Random
Off
VOL –
VOL +
/Enter/Play Mode
CH –
Note:
In playing back the Video CD with PBC, you can not set
Random playback.
33
5K70101B [E] (P33-41)
33
20/4/04, 15:54
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced playback
Changing angles/Title selection/DVD menu
TOP MENU
ANGLE
DVD MENU
▲/ ▼ /
/
ENTER
PLAY
Changing angles
When playing back a disc recorded with multi-angle facility, you can change the angle that you are viewing the scene from.
Press ANGLE during playback.
Press ANGLE repeatedly until the desired angle
is selected.
1
2
The current angle will appear.
ANGLE
ANGLE
1/9
Note:
Depending on the DVD, you may not be able to change the
angles even if multi-angles are recorded on the DVD.
Title selection
Two or more titles are recorded on some discs. If the title menu is recorded on the disc, you can select the desired title.
Press TOP MENU during playback.
Press ENTER or PLAY.
1
2
TOP MENU
3
The playback of the selected title will
start.
Title menu appears on the screen.
ENTER
PLAY
Press
/
/
/
to select the desired title.
CH +
VOL –
VOL +
Note:
Depending on the DVD, you may not be able to select the title.
Depending on the DVD, a “title menu” may simply be called a
“menu” or “title” in the instructions supplied with the disc.
CH –
DVD menu
Some DVDs allow you to select the disc contents using the menu.
When you play back these DVDs, you can select the subtitle language and sound-track language, etc. using the menu.
Press DVD MENU during playback.
Press ENTER.
The DVD menu appears on the screen.
1
2
3
The menu continues to another
screen. Repeat steps 2 and 3 to set
the item completely.
DVD MENU
ENTER
• Press DVD MENU again to resume
playback at the scene when you
pressed DVD MENU.
Press
/
/
/
to select the desired item.
Note:
Depending on the DVD, you may not be able to resume playback
from the scene point when you pressed the DVD MENU button.
CH +
VOL –
VOL +
CH –
34
5K70101B [E] (P33-41)
34
20/4/04, 15:54
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing soundtrack language/
Subtitles
AUDIO
SUBTITLE
DVD
VCD
Changing soundtrack language
Subtitles
You can select the language when you play a multilingual When playing back a disc recorded with subtitles, you can
disc.
select the subtitle language or turn the subtitle off.
Press AUDIO during playback.
PressSUBTITLErepeatedlyduringplaybackuntil
your desired language appears.
1
1
The current soundtrack language will
appear.
AUDIO
SUBTITLE
1/8 Eng
To turn off the subtitle, press SUBTITLE until
“Off” appears.
2
Press AUDIO repeatedly until the desired lan-
guage is selected.
SUBTITLE
2
AUDIO
Off
•
The on screen display will disappear after a
few seconds.
• The on screen display will disappear after a few
seconds.
Notes:
• Depending on the DVD, you may not be able to change
subtitles, or to turn subtitles on or off.
• While playing a DVD, the subtitle may change when
you open or close the disc tray.
In case of Video CD playback
Audio type changes as follows each time you press AUDIO.
• In some cases, a selected subtitle language may not
be changed immediately.
LR
L
R
Notes:
• If the desired language is not heard after pressing the
button several times, the language is not recorded on
the disc.
• Changing soundtrack language is cancelled when you
open the disc tray. The initial default language or available
language will be heard if the disc is played back again.
• If you select DTS in playing DTS-encoded disc, no sound
will be heard from the TV/DVD’s speakers.
35
5K70101B [E] (P33-41)
35
20/4/04, 15:54
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced playback
RECALL
1
Karaoke playback/Disc status/
To turn off the PBC
AUDIO
/
ENTER
DVD
VCD
CD
Disc status
Karaoke playback
You can turn the vocal on or off recorded on the DVD
KARAOKE.
With each press of RECALL, the status of the disc
will appear on the screen and change as follows.
RECALL
During DVD KARAOKE disc playback, press
AUDIO.
1
The KARAOKE symbol ( ) appears.
DVD
AUDIO
00:34:56 01:12:33
00:34:56 01:12:33
1/99 Chapter 1/999
1/9
1/8 Eng Dolby Digital
Title
1/8 EngDolby Digital
1/32 Eng
Off
• If you play non-Karaoke disc, the KARAOKE sym-
bol ( ) does not appear.
• Some Karaoke discs may not have the vocal on/
off function. In this case, the KARAOKE symbol
To make status display disappear, press RECALL
again.
Video CD
(
) does not appear.
00:12
04:32
PBC
00:12
04:32
Track –/–
Press B or A to select “On” or “Off”.
2
VOL –
VOL +
1/8 Eng Dolby Digital
On
To make status display disappear, press RECALL
again.
Audio CD
On : The primary vocal is output when it is
recorded on the disc.
Off : The primary vocal is not output.
34:56
71:33
Track 11/99
• The on screen display will disappear after a
few seconds.
When you playback the CD disc, the status display
will appear on the screen and continue displaying.
Notes:
• The vocal output feature is used during playback of Dolby
Digital (multi-channel) recorded DVD KARAOKE discs. This
feature allows you to turn off vocal audio tracks, or restore
them for background accompaniment.
VCD
To turn off the PBC
• When playing Karaoke, connect appropriate audio equipment
such as an amplifier to the TV/DVD.
Press number button 1 in the stop mode, then
press ENTER.
ENTER
1
36
5K70101B [E] (P33-41)
36
20/4/04, 15:54
Download from Www.Somanuals.com. All Manuals Search And Download.
MP3/WMA/JPEG CD operation
This unit can play back the MP3/WMA/JPEG-data which has been recorded on CD-R or CD-RW.
To produce the MP3/WMA/JPEG-data, you need a Windows-PC with CD-R/RW drive and a MP3/WMA/JPEG-encoding
Software (not supplied).
The Apple-HFS-System can not be played.
CD
MP3/WMA/JPEG CD information
Limitations on MP3/WMA/JPEG CD playback
• MP3/WMA/JPEG CD is the disc that is standardized by ISO9660, its file name must include 3-digits exten-
sion letters, “mp3”, “wma”, “jpg”.
• MP3/WMA/JPEG CD must be correspond to the ISO standardized files.
• This unit can read 200 files per disc. If one directory has more than 200 files, it reads up to 200 files, the
remaining files will be omitted.
• The unit is able to recognize up to a maximum of 50 directories per disc.
• MP3/WMA/JPEG CDs cannot be used for the purpose of recording.
• If the CD has both audio tracks and MP3/WMA/JPEG files, only audio tracks are played.
• It may take more than one minute for this unit to read MP3/WMA/JPEG files depending on its structure.
• Music recorded by “Joliet Recording Specification” can be played back, the file name is displayed (within 16
letters) on the screen. Long file names will be condensed.
• The music files recorded by “Hierarchical File System” (HFS) cannot be played.
Limitations on display
• The maximum number for display is 16 letters.
Available letters for display are the following:
capital or small alphabets of A through Z, numbers of 0 through 9, and _ (under score).
• Other letters than those above are replaced in hyphen.
Notes on MP3/WMA/JPEG files
To play back MP3/WMA/JPEG CD in the recorded order,
1.Use MP3/WMA/JPEG software that records data alphabetically or numerically.
2.Name each file including two-digit or three-digit number (ex. “01” “02” or “001” “002”).
3.Refrain from making too many sub-folders.
CAUTION:
• Some MP3/WMA/JPEG CDs can not be played back depending on the recording conditions.
• The CD-R/RW that has no music data or non MP3/WMA/JPEG files can not be played back.
Standard, sampling frequency, and the bit rate:
MP3 CD
MPEG-1 Audio
32kHz, 44.1kHz, 48kHz
32kbps ~ 320kbps (constant bit rate or variable bit rate)
The recommend recording setting for a high-quality sound is 44.1kHz of sampling frequency and 128kbps of
constant bit rate.
WMA CD
WMA version 7, and 8
32kHz, 48kbps
44.1kHz, 48kbps ~ 192kbps
48kHz, 128kbps ~ 192kbps
The file recorded by mono, 48kHz, 48 kbps is not available to this unit.
37
5K70101B [E] (P33-41)
37
20/4/04, 15:54
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced playback
MP3/WMA/JPEG CD operation (continued)
0–9
TOP MENU
▲/▼ /
ENTER
PLAY
/
STOP
CD
MP3/WMA CD playback
Press STOP to end playback.
Place a disc on which MP3 or WMA files have
been recorded onto the disc tray.
5
1
2
STOP
A file menu screen will appear on the screen.
• The unit records the stopped point. “ ” appears on
the screen. Press PLAY to resume playback (from
the scene point).
• If you press STOP again or unload the disc, the unit
will clear the stopped point.
Press B/A or ENTER to select folder.
VOL –
VOL +
ENTER
About file menu
Press C/D/B/A or Number buttons (0–9) to
select the desired file.
3
1
4
7
2
5
8
0
3
6
9
CH +
CH –
VOL –
VOL +
• In case the folder includes more than 15 files, press
B or A to display next file list.
Notes:
• The picture menu is displayed when the FUJICOLOR CD
or the Kodak Picture CD are played. To display the file
menu, press TOP MENU.
• In the case of a CD containing a mixture of MP3, WMA and
JPEG files, the files are played back by selecting them from
the file menu.
• When PLAY has been pressed after displaying the
file menu, or when the disc tray has been closed
using PLAY, playback begins automatically starting
from the first file. In this case, if the first file is an
MP3/WMA file, only MP3/WMA files are played back
in order. If the first file is a JPEG file, the first JPEG
file is played back.
• MP3 or WMA file on the Kodak Picture CD is not recog-
nized on this unit.
Notes:
• During MP3/WMA/JPEG playback, you can not use JUMP, A-
B Repeat functions.
• You can use Repeat (Track or All), Random functions and
Program playback for MP3/WMA/JPEG CD playback (see
pages 32 and 33).
• In the case of a CD containing a mixture of MP3, WMA and
JPEG files, the files are played back by selecting them from
the file menu.
Press ENTER.
The selected file starts playing back.
4
ENTER
• During MP3/WMA playback, you can not adjust the volume
level using the VOL +/– buttons on the remote. In this case,
please use the VOLUME C/D buttons on the unit.
38
5K70101B [E] (P33-41)
38
20/4/04, 15:54
Download from Www.Somanuals.com. All Manuals Search And Download.
0–9
You can select your desired JPEG file on the file menu and picture menu.
The selected JPEG file is automatically adjusted to the TV screen. (When the
aspect ratio of the JPEG file is different to your TV screen, the black bar will
appear at the top and bottom, or the both sides of the TV screen.
ANGLE
TOP MENU
DVD MENU
▲/▼ /
ENTER
PLAY
/
STOP
SKIP 6/7
PAUSE
CD
CD
JPEG CD playback
Slide show playback
The slide show enables you to view pictures (files) one after
another automatically.
Place a disc on which JPEG files have been
recorded onto the tray.
1
2
Preparation:
• Set “JPEG Interval” setting to “5 Seconds”, “10 Seconds”
A file menu screen will appear on the screen.
Press B/A to select folder.
or “15 Seconds”
.
41
Select your desired starting file for the slide
show in the step 3 as left.
1
2
VOL –
VOL +
Press ENTER to start slide show from the
selected file.
ENTER
Press C/D/B/A or Number buttons (0–9) to
select the desired file.
To display a picture menu, press DVD MENU.
(To return to a file menu, press TOP MENU.)
Press B/A or C/D to select the desired file.
3
• If you press PAUSE during the slide show, the slide
show stops temporary. “ 4 ” appears briefly on the
picture.
If the picture appears upside down or sideways,
press ANGLE repeatedly until it’s right side up.
1
4
7
2
5
8
0
3
6
9
CH +
CH –
DVD MENU
TOP MENU
VOL –
VOL +
“
”, “
”, “
” or “
” appears briefly
on the screen.
Press PLAY or SKIP
• To display next list, press SKIP
/
.
again to resume the slide
• When PLAY has been pressed after displaying
the file menu, or when the disc tray has been
closed after pressing PLAY, playback begins
automatically starting from the first file. In this
case, if the first file is a JPEG file, the first JPEG
file is played back. If the first file is an MP3/
WMA file, only MP3/WMA files are played back
in order.
show.
• When the slide show playback finished the file list
appears.
• To stop the slide show, press STOP. The file list ap-
pears.
Press ENTER. The selected picture appears
on the screen.
4
5
ENTER
Rotating an image
You can rotate an image by 90 degrees by press-
ing ANGLE during playback of the image.
“
”, “
”, “
” or “
” appears
briefly on the screen.
Press STOP to end playback.
The file menu appears on the screen.
If you want to watch the other file, repeat steps
3 ~ 4.
STOP
39
5K70101B [E] (P33-41)
39
20/4/04, 15:54
Download from Www.Somanuals.com. All Manuals Search And Download.
Function setup
Customizing the function settings
You can change the default settings to customize performance to your
preference.
SETUP
▲/▼ /
ENTER
/
RETURN
DVD
VCD
CD
Setting procedure
Press SETUP during stop mode.
Press C or D to select the desired option.
1
2
3
4
SETUP/MENU
CH +
The following on-screen display
appears.
CH –
Language Picture Sound Parental Other
Change the selection using C/D/B/A or ENTER,
by referring to the corresponding pages 41 and
42.
CH +
/Enter/Setup/Return
• Repeat step 3 and 4 to change
other settings.
• Press C to select another
operation, go back to step 2.
VOL –
VOL +
CH –
Press B or A to select the desired section, then
press D or ENTER.
ENTER
VOL –
VOL +
To make SETUP screen disappear, press
SETUP or RETURN.
CH –
5
SETUP/MENU
ENTER
RETURN
Page
Section
Option
Details
Menu
To select the language of “Menu”, “Subtitle” and “Audio” if
their languages are recorded onto the disc more than one
language.
Language
Subtitle
Audio
41
41
Tv Screen
Display
To select a picture size according to the aspect ratio of your TV.
To turn on or de-activate the operational status display on the
screen.
41
41
41
Picture
JPEG Interval
Select Files
To select a preferred setting for the slide show playback.
To select your desired file type for playing back a containing a
mixture of MP3, WMA, JPEG files.
Sound
Parental
Other
42
42
DRC
To select On or Off for DRC (Dynamic Range Control).
Input 4-digit password to set the parental level.
Password
Parental
To select a preferred parental level for the parental setting.
To select a preferred language for on screen display.
42
OSD Language
40
5K70101B [E] (P33-41)
40
20/4/04, 15:55
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting details
Language Picture Sound Parental Other
Language Picture Sound Parental Other
Picture
Language
Tv Screen
Display
JPEG Interval
Select Files
4:3
On
Off
All
4:3
4:3
16:9
Menu
Subtitle
Audio
English
Automatic Francais
English
English
Espanol
Other
/Enter/Setup/Return
/Enter/Setup/Return
Menu, Subtitle, Audio
Tv Screen
You can select the language of “Menu”, “Subtitle” and
“Audio” if more than one languages are recorded onto
the disc.
You have the following screen sizes to choose from:
4:3 Letter box:
Select this mode when connecting to a conventional TV.
When playing back a wide screen-DVD disc, it displays
the wide picture with black bands at the top and bottom
of screen.
English, Francais, Espanol:
The selected language will be heard or seen.
Other:
Other language can be selected (see the “Language
code list” on page 44).
4:3
Pan scan:
It displays the wide picture on the whole screen with left
and right edges automatically cut off.
Original: (Audio)
The unit will select the first priority language of each
disc.
16:9
Wide:
Select this mode when connecting to a wide-screen TV.
A wide screen picture is displayed full size.
Automatic: (Subtitle)
•
The unit will automatically select the same
language in the AUDIO setting.
Note:
If the DVD disc is not formatted in the pan & scan style, it
displays 4:3 style.
• When the unit selects the same language as
the AUDIO, the subtitles will not appear during
playback.
• When you do not use the same language as
the AUDIO, the subtitles will appear during
playback.
Display
On screen display can be switched on or off when you
press the buttons.
On: On screen displays appear when you press the
buttons (factory setting).
Off: On screen displays do not appear when you
press any buttons.
Off: (Subtitle)
Subtitles do not appear.
Note:
If the selected language is not recorded on the disc, the
first-priority language is selected.
JPEG Interval
YoucancontinuouslyplaybackallJPEGfilesautomatically.
After the setting below, start playing the disc on which
JPEG files have been recorded.
Off:
Plays back one file at a time.
5 Seconds:
Plays back images in the form of a slide show at
5 second intervals.
10 Seconds:
Plays back images in the form of a slide show at
10 second intervals.
15 Seconds:
Plays back images in the form of a slide show in
15 second intervals.
Select Files
When playing back a CD containing a mixture of MP3,
WMA and JPEG files, only MP3/WMA or JPEG files can
be displayed on the file menu.
All:
Displays all files.
Music Only:
Displays only MP3/WMA files.
Pictures Only:
Displays only JPEG files.
41
5K70101B [E] (P33-41)
41
20/4/04, 15:55
Download from Www.Somanuals.com. All Manuals Search And Download.
Function setup
Customizing the Function Settings (continued)
Setting details
To change the parental level
Language Picture Sound Parental Other
Sound
1) Press C or D to select “Password”.
2) Press Number buttons (0–9) to enter the password
you have stored.
On
Off
DRC
On
3) Press ENTER.
/Enter/Setup/Return
• The rating is now unlocked.
4) Press C or D to select “Parental”, then press B
or A to change the parental level.
5) Press C or D to select “Password”, then press
Number buttons (0–9) to enter the password.
Note: You can change the password if you want.
6) Press ENTER.
DRC
DRC (Dynamic Range Control) enables you to control
the dynamic range so as to achieve a suitable sound for
your equipment.
On: Loud sound such as explosion or similar is toned
down slightly when played back. This makes it
suitable for when it is connected to a stereo.
Now the parental level is changed and locked.
If you forget the password...
1. Press OPEN/CLOSE to open the disc tray.
2. Remove the disc.
3. Press OPEN/CLOSE again to close the disc tray.
“No Disc” appears on the screen.
4. While holding STOP down on the front panel, press 7
on the remote control. “PASSWORD CLEAR” appears
on the screen.
Off: It plays back at the recording level on the disc.
Notes:
• This function works only during playback of Dolby Digital
recorded discs.
• The level of Dynamic Range Reduction may differ
depending on DVD video disc.
5. Enter a new password again.
Language Picture Sound Parental Other
Parental
Notes:
Password
• Depending on the discs, the unit may not be able to limit
playback.
Parental
Off
• Some discs may not be encoded with specific rating level
information though its disc jacket says “adult.”
For those discs, the parental control feature will not work.
0
9/Cancel
/Enter/Setup/Return
Parental control setting
Some discs are specified not suitable for children.
Suchdiscscanbelimitednottoplaybackwiththeunit.
Language Picture Sound Parental Other
Other
1) Press C or D to select “Parental”, then press B
OSD Language English
English
Francais
Espanol
or A until the level you require appears.
• Level Off:
The parental control setting does not
function.
/Enter/Setup/Return
• Level 8:
• Level 1:
All DVD software can be played back.
DVD software for adults cannot be
played back.
OSD Language
The setup language can be selected.
Select from the level 1 to level 8. The limitation will
be more severe as the level number is lower.
2) Press C or D to select “Password”.
Press Number buttons (0–9) to input a 4-digit
password. Be sure to remember this number!
• If you input a wrong number, press CANCEL.
3) Press ENTER to store the password.
Note: Now the rating is locked and the setting can
not be changed unless you enter the correct pass
word.
English: To display OSD language is English.
Francais: To display OSD language is Francais.
Espanol: To display OSD language is Espanol.
Note:
If each setup (pages 41 and 42) has been completed, the unit
can always be worked under the same conditions (espe-
cially with DVD discs).
Each setup will be retained in the memory even if you turn
the power off.
Notes:
• Depending on the discs, the unit cannot limit playback.
• Some discs may not be encoded with specific rating
level information though its disc jacket says “adult.” For
those discs, the age restriction will not work.
42
5K70101B [E] (P42-43)
42
20/4/04, 15:55
Download from Www.Somanuals.com. All Manuals Search And Download.
Temporary disabling of rating level by DVD disc
0–9
OPEN/CLOSE
Depending on the DVD disc, the disc may try to temporarily cancel the rating
level that you have set.
It is up to you to decide whether to cancel the rating level or not.
▲/▼
ENTER
RETURN
PLAY
Load a DVD disc and press PLAY or OPEN/
Enter the password with Number buttons (0–9).
Then press ENTER.
CLOSE on the unit
.
28
1
2
4
If you interrupt the entering, press
RETURN.
1
4
7
2
5
8
0
3
6
9
PLAY
Please enter the
OPEN/CLOSE
-
4
digit password
ENTER
Enter/0 9/Cancel/Return
IftheDVDdischasbeendesignedtotemporarily
canceltheRatinglevel, thescreenwhichfollows
the “Reading” screen will change, depending on
which disc is played. If you select “YES” with the
ENTER key, “Your disc exceeds the parental
control level#.” screen will then appear.
RETURN
Playback will commence if the entered
password was correct.
5
Reading
Your disc exceeds
the parental control level#.
Parental Control Level
Cancel Picture
Note:
This temporary cancellation of rating level will be kept until the
disc is ejected.
/Enter/Return
When the disc is ejected, the original rating level will be set again
automatically.
If you wish to cancel the set rating level temporarily,
select “Parental Control Level” with
or
, then
3
press ENTER. If the 4-digit password at step 2 on
page 42 has been set, the password entering
screen will appear as shown in step 4.
Alternatively, if the password has not been set,
playback will commence. If you don’t know (or have
forgotten) the password, select “Cancel Picture”.
The setting screen will disappear. Press OPEN/
CLOSE to remove the disc.
CH +
CH –
ENTER
OPEN/CLOSE
43
5K70101B [E] (P42-43)
43
20/4/04, 15:55
Download from Www.Somanuals.com. All Manuals Search And Download.
Others
Language code list
Enter the appropriate code number for the initial settings “Menu”, “Subtitle” and/or “Audio”
.
41
Language Name Code Language Name Code Language Name Code Language Name Code
Abkhazian
Afar
1112 Fiji
1620 Lingala
1619 Lithuanian
1628 Macedonian
1635 Malagasy
1722 Malay
2224 Singhalese
2230 Slovak
2321 Slovenian
2317 Somali
2329 Spanish
2322 Sundanese
2330 Swahili
2319 Swedish
2328 Tagalog
2325 Tajik
2919
2921
2922
2925
1529
2931
2933
2932
3022
3017
3011
3030
3015
3018
1225
3019
3025
3028
3021
3033
3121
3128
3136
3219
3225
1335
3325
3418
2019
3525
3631
1111 Finnish
1116 French
2927 Frisian
1123 Galician
1128 Georgian
1835 German
1129 Greek
1135 Greenlandic
1136 Guarani
1211 Gujarati
1531 Hausa
Afrikaans
Albanian
Amharic
Arabic
2111 Malayalam
1415 Maltese
1522 Maori
Armenian
Assamese
Aymara
Azerbaijani
Bashkir
2122 Marathi
1724 Moldavian
1731 Mongolian
1811 Nauru
2324 Tamil
Basque
2411 Tatar
Bengali; Bangla 1224 Hebrew
1933 Nepali
2415 Telugu
2425 Thai
Bhutani
Bihari
1436 Hindi
1819 Norwegian
1831 Oriya
1218 Hungarian
1228 Icelandic
1217 Indonesian
2335 Interlingua
1215 Irish
2528 Tibetan
2611 Tigrinya
Breton
1929 Panjabi
Bulgarian
Burmese
Byelorussian
Cambodian
Catalan
Chinese
Corsican
Croatian
Czech
1924 Pashto, Pushto 2629 Tonga
1911 Persian
1711 Polish
1611 Turkish
2622 Turkmen
2630 Twi
2123 Italian
1930 Portuguese
2011 Quechua
1311 Japanese
3618 Javanese
1325 Kannada
1828 Kashmiri
1329 Kazakh
1411 Kirghiz
2422 Korean
1524 Kurdish
1525 Laothian
1530 Latin
2731 Ukrainian
2033 Rhaeto-Romance2823 Urdu
2124 Romanian
2129 Russian
2121 Samoan
2135 Sanskrit
2125 Scots Gaelic
2131 Serbian
2825 Uzbek
2831 Vietnamese
2923 Volapük
2911 Welsh
1714 Wolof
Danish
Dutch
English
2928 Xhosa
Esperanto
Estonian
Faroese
2225 Serbo-Croatian 2918 Yiddish
2211 Shona
2924 Yoruba
2914 Zulu
1625 Latvian, Lettish 2232 Sindhi
44
5K70101B [E] (P44-48)
44
20/4/04, 15:55
Download from Www.Somanuals.com. All Manuals Search And Download.
Reception disturbances
Most types of television interference can be remedied by adjusting the height and position of the VHF/UHF
antenna. Outdoor antennas are recommended for best results. The most common types of television
interference are shown below. If one of these symptoms appear when the TV/DVD is connected to a Cable
TV system, the disturbance may be caused by the local Cable TV company broadcast.
IGNITION
Black spots or horizontal streaks may appear, the picture may flutter or
drift. Usually caused by interference from automobile ignition systems,
neon lamps or AC powered tools and appliances such as drills or hair
dryers.
GHOSTS
Ghosts are caused by the television signal following two paths. One is
the direct path and the other is reflected by tall buildings, hills or other
large objects. Changing the direction or position of the antenna may
improve the reception.
SNOW
If the TV/DVD is located far from the TV station, in a fringe reception
area where the signal is weak, small dots may appear in the picture.
If the signal is extremely weak, the installation of a larger external
antenna may be necessary.
RADIO FREQUENCY INTERFERENCE (RFI)
Caused by two-way radios, this type of interference produces moving
ripples or diagonal streaks in the picture. Some cases may cause a
loss of contrast in the picture. Changing the direction and position of
the antenna or installing an RFI filter may improve the picture.
PICTURE SIZE VARIATION
A slight picture size variation is normal when you adjust the CONTRAST
or BRIGHTNESS settings.
CARE AND MAINTENANCE
To prevent fire or shock hazard, disconnect the TV/DVD from the power source before cleaning.
The finish on the cabinet may be cleaned with mild soap and a soft, damp cloth and cared for as other furniture.
Use caution when cleaning or wiping the plastic parts.
45
5K70101B [E] (P44-48)
45
20/4/04, 15:55
Download from Www.Somanuals.com. All Manuals Search And Download.
Others
Troubleshooting
Use the following check list for troubleshooting when you have problems with your unit. Consult your local dealer
or service outlet if problems persist.
Be sure all connections are properly made when using with other units.
SYMPTOMS
POSSIBLE SOLUTIONS
PAGE
POWER
• Make sure the power cord is plugged in.
• Try another AC outlet.
• Power is off, check fuse or circuit breaker.
• Unplug unit, then plug it back in.
5
TV/DVD does not operate.
TV BROADCAST RECEPTION
• Station or Cable TV experiencing problems, tune to another station. 14
Poor sound or No sound.
• Check Volume adjustments.
• Check for sources of possible interference.
20
45
14
14
45
26
• Station or Cable TV experiencing problems, tune to another station.
• Check antenna or Cable TV connections, reorient antenna.
• Check for sources of possible interference.
Poor picture or No picture.
• Check picture control adjustments.
•
Station or Cable TV experiencing problems, tune to another station. 14
Poor reception on some channels.
• Station signal is weak, reorient antenna to receive weaker station. 13,14
• Check for sources of possible interference.
45
• Station or Cable TV experiencing problems, tune to another station.
• Make sure channels are set into memory.
• Check picture control adjustments.
• Check antenna or Cable TV connections, reorient antenna.
• Check for sources of possible interference.
14
23
26
14
45
Poor color or no color.
14
23
–
• Station or Cable TV experiencing problems, tune to another station.
• Make sure channels are set into memory.
• Cable TV company is scrambling signal.
• Check antenna orientation.
• Check all Cable TV connections.
• Set TV/CABLE selection to the CABLE position.
• Station or Cable TV system problems, try another station.
Picture wobbles or drifts.
No CATV reception.
13
14
23
20
Horizontal or diagonal bars on
screen.
• Check antenna connections, reorient antenna.
• Check for sources of possible interference.
13,14
45
• Make sure TV/CABLE selection is in the appropriate position.
• If using antenna, check UHF antenna connections.
23
13
No reception above channel 13.
• No broadcast on station tuned.
• Sleep Timer is set.
• Power interrupted.
23
21
–
TV shuts off.
• TV station experiencing problems or program tuned is not closed
captioned. Try another channel.
• Check Cable TV connection or VHF/UHF antenna, reposition or
rotate antenna.
• Press CLOSED CAPTION button to turn on the closed caption
decoder.
20
13,14
22
Closed - Caption is not activated.
Display is not shown in your
language.
• Select proper language in the menu options.
19
46
5K70101B [E] (P44-48)
46
20/4/04, 15:55
Download from Www.Somanuals.com. All Manuals Search And Download.
SYMPTOMS
POSSIBLE SOLUTIONS
PAGE
DVD
• No disc is inserted.
• The disc may be dirty. Clean up the disc.
• The unit cannot play CD-ROMs, etc.
28
7
8
Playback doesn’t start.
No picture.
• TV/DVD selector is not set correctly.
28
• Check the input selector of the amplifier is set properly.
• The unit is in the special playback mode.
• Select the correct Audio Output position on AV amplifier.
–
30
15
No sound.
Picture is distorted during fast
reverse/forward playback.
• The picture will be distorted occasionally.
–
Stopping playback, search, slow-
motion play, repeat play, or
program play, etc. cannot be
performed.
• Some discs may not do some of the functions.
–
No 4:3 (16:9) picture.
No on-screen display.
No surround sound.
• Select appropriate screen size.
• Select Display On.
41
41
15
• The setup does not match your stereo system.
The unit or remote operation key
is not functioning.
• Turn off the unit and unplug the AC power cord for several min-
utes, then replug it.
–
Playback does not start when the
title is selected.
• Check the RATING LEVEL setup.
42
Audio soundtrack and/or subtitle
language is not changed when
you play back a DVD.
• Multilingual language is not recorded on the DVD disc.
35
35
• Some discs have no subtitles.
• Subtitles are cleared. Press the SUBTITLE button.
No subtitle.
Angle cannot be changed.
• Multi-angles are not recorded on the DVD disc.
• The function is prohibited with the unit or the disc.
34
30
“
” appears on the screen.
REMOTE CONTROL
The remote control does not
function.
• Aim the remote control at the remote sensor.
• Operate within approx. 5 meters or reduce the light in the room.
• Clear the path of the beam.
12
• The batteries are weak. Replace the batteries.
• Check the batteries are inserted correctly.
47
5K70101B [E] (P44-48)
47
20/4/04, 15:55
Download from Www.Somanuals.com. All Manuals Search And Download.
Others
Specifications
General
Power supply
Power consumption
Picture tube
Speaker
Audio output power
Weight
AC 120 V 60 Hz
Operation: 115 W, Stand by: 4 W
Type 20 (508 mm diagonal)
1-13/16 x 3-7/8 inches (46 x 99 mm), 8 ohm x 2
5 W + 5 W
55.1 lbs (25.0 kg)
Dimensions
Width: 22-5/8 inches (574 mm)
Height: 20-1/4 inches (514.5 mm)
Depth: 18-15/16 inches (481.5 mm)
181 channel freq. synthesized
Tuner
VHF
2-13
UHF
CATV
14-69
125 Channels
Antenna input
UHF/VHF: 75 Ω coaxial
Applicable disc
DVD (12 cm, 8 cm), CD (12 cm, 8 cm)
Frequency range
Operating conditions
DVD: 4 Hz-22 kHz, CD: 4 Hz-20 kHz
Temperature: 5˚C-40˚C (41˚F-104˚F), Operating status: Horizontal
Input/Output
Video input
1.0 V (p-p), 75 Ω, negative sync., pin jack x 2
–8 dBm, 50 kΩ, negative sync., pin jack (L/R) x 2
0.5 V (p-p), 75 Ω, pin jack x 1
Audio input
Audio output (DIGITAL COAXIAL)
Supplied accessories
Remote control (DC-FN20S) ................................ 1
Batteries (R03/AAA) ............................................. 2
300-75 Ω matching transformer ............................ 1
• Designs and specifications are subject to change without notice
48
5K70101B [E] (P44-48)
48
20/4/04, 15:55
Download from Www.Somanuals.com. All Manuals Search And Download.
Limited warranty
Toshiba America Consumer Products, L.L.C. (“TACP”) makes the following limited warranties. These limited
warranties extend to the original consumer purchaser or any person receiving this set as a gift from the original
consumer purchaser and to no other purchaser or transferee .
Limited Ninety (90) Day Warranty
TACP warrants this product and its parts against defects in materials or workmanship for a period of ninety (90)
days after the date of original retail purchase. During this period, TACP will repair a defective product or part,
without charge to you. You must deliver the entire set to an Authorized TACP Service Station. You pay for all
transportation and insurance charges for the set to and from the Service Station.
Limited One (1) Year Warranty
TACP further warrants the parts in this product against defects in materials or workmanship for a period of one
year after the date of original retail purchase. During this period TACP will replace a defective part without
charge to you, except that if a defective part is replaced after ninety (90) days from the date of original retail
purchase you pay labor charges involved in the replacement. You must also deliver the entire product to a TACP
Authorized Service Station. You are responsible for all transportation for the set to and from the Service Station.
Limited Two (2) Year Warranty of Picture Tube
TACP further warrants the picture tube in this product against defects in materials or workmanship for a period of
two (2) years after the date of original retail purchase. During this period, TACP will replace a defective picture
tube without charge to you except that if a defective picture tube is replaced after ninety (90) days from the date
of the original retail purchase, you pay labor charges involved in the replacement. You are responsible for all
charges involved in the replacement. You are responsible for all transportation and insurance charges for the set
to and from the Service Station.
Rental Units
The warranty for rental units begins with the first rental or thirty (30) days from the date of shipment to the rental
firm, whichever comes first.
Commercial Units
Products sold and used for commercial use have a limited ninety (90) day warranty for all parts, labor and picture
tube.
Owner's Manual and Demographic Card
You should read this owner's manual thoroughly before operating this product. You should complete and mail the
enclosed Demographic card within ten days after you, or the person who has given you this product as a gift,
purchased this product. This is one way to enable TACP to provide you with better customer service and
improved products. Failure to return the Demographic card will not affect your rights under this warranty.
Your Responsibility
The above warranties are subject to the following conditions:
( 1 ) You must retain your bill of sale or provide other proof of purchase.
( 2 ) All warranty servicing of this product must be made by an Authorized TACP Service Station.
( 3 ) These warranties are effective only if the product is purchased and operated in the U.S.A. or Puerto Rico.
( 4 ) Labor service charges for set installation, set up, adjustment of customer controls and installation or repair
of antenna systems are not covered by this warranty. Reception problems caused by inadequate antenna
systems are your responsibility.
( 5 ) Warranties extend only to defects in materials or workmanship as limited above and do not extend to any
product or parts which have been lost or discarded by you or to damage to products or parts caused by
misuse, accident, damage caused by Acts of God, such as lightning or fluctuations in electric power,
improper installation, improper maintenance or use in violation of instructions furnished by us; or to units
which have been altered or modified without authorization of TACP.
49
5K70101B [E] (P49-Back)
49
20/4/04, 15:55
Download from Www.Somanuals.com. All Manuals Search And Download.
Limited warranty (continued)
How to Obtain Warranty Service
If after following all of the operating instructions in this manual and checking the section “Troubleshooting”
and you still find that service is needed;
( 1 ) Call the TACP toll free number 1-800-631-3811 after you find a defective product or part to find the
nearest Toshiba Authorized Service Station.
( 2 ) Please present your bill of sale or other proof to the Authorized Service Station.
“TACP Authorized Service Station personnel will come to your home when warranty service is re-
quired. Depending on the type of repair required, the service will either be performed in your home or
the set will be taken to the TACPAuthorized Service Station for repair and returned to your home at no
cost to you”.
In the Continental United States contact:
Toll Free
1-800-631-3811
All warranties implied by state law, including the implied warranties of merchantability and fitness for a particular
purpose, are expressly limited to the duration of the limited warranties set forth above. With the exception of
any warranties implied by state law as hereby limited, the foregoing warranty is exclusive and in lieu of all other
warranties, guarantees, agreements and similar obligations of manufacturer or seller with respect to the repair
or replacement of any parts. In no event shall TACP be liable for consequential or incidental damages.
No person, agent, distributor, dealer or company is authorized to change, modify or extend the terms of these
warranties in any manner whatsoever. The time within which action must be commenced to enforce any
obligation of TACP arising under this warranty or under any statute, or law of the United States or any state
thereof, is here by limited to 90 days from the date you discover or should have discovered, the defect. This
limitation does not apply to implied warranties arising under state law.
This warranty gives you specific legal rights and you may also have other rights which may vary from state to
state. Some states do not allow limitation on how long an implied warranty lasts, when an action may be
brought, or the exclusion or limitation of incidental or consequential damages, so the above provisions may not
apply to you.
ATTENTION CANADIAN CONSUMERS:
Canadian consumers are requested to complete the special Canadian “Warranty Registration
Form” enclosed, and forward this completed form with a copy of bill of sale to TOSHIBA OF
CANADA to “Register and Validate” their warranty.
Products purchased in the U.S.A. and used in Canada are not covered by these warranties.
Products purchased in Canada and used in the U.S.A. are not covered by these warranties.
Rev. 09-01-98
50
5K70101B [E] (P49-Back)
50
20/4/04, 15:55
Download from Www.Somanuals.com. All Manuals Search And Download.
Memo
...................................................................................................................................
...................................................................................................................................
...................................................................................................................................
...................................................................................................................................
...................................................................................................................................
...................................................................................................................................
...................................................................................................................................
...................................................................................................................................
...................................................................................................................................
...................................................................................................................................
...................................................................................................................................
...................................................................................................................................
...................................................................................................................................
...................................................................................................................................
...................................................................................................................................
...................................................................................................................................
...................................................................................................................................
...................................................................................................................................
...................................................................................................................................
...................................................................................................................................
...................................................................................................................................
...................................................................................................................................
...................................................................................................................................
...................................................................................................................................
...................................................................................................................................
...................................................................................................................................
...................................................................................................................................
...................................................................................................................................
...................................................................................................................................
...................................................................................................................................
...................................................................................................................................
...................................................................................................................................
...................................................................................................................................
...................................................................................................................................
...................................................................................................................................
...................................................................................................................................
...................................................................................................................................
...................................................................................................................................
...................................................................................................................................
...................................................................................................................................
5K70101B [E] (P49-Back)
51
20/4/04, 15:55
Download from Www.Somanuals.com. All Manuals Search And Download.
04/03
U
5K70101B [E] (P49-Back)
52
20/4/04, 15:55
Download from Www.Somanuals.com. All Manuals Search And Download.
|