Toshiba Server 510D User Manual

Toshiba MAGNIA™ 510D  
Read-Me-First Addendum  
Thank you for purchasing the Toshiba MAGNIA 510D.  
This document explains the precautions for using your  
MAGNIA 510D. To ensure the best performance,  
please read this document carefully before configuring  
the server.  
Keep the document handy for future reference.  
For the latest information and updates, please visit:  
When using Windows NT Server 4.0  
(1) Be sure to connect a mouse to the server.  
If you use the server without a mouse, the keyboard  
may become inoperative.  
(2) Installing Windows NT Server 4.0 to the server  
whose memory capacity exceeds 1,7MB  
When the memory capacity exceeds 1,7MB,  
Windows NT Server 4.0 cannot be installed because  
of the limitations of Windows NT Server 4.0. In this  
case, use the following procedure to install  
Windows NT Server 4.0.  
1/15  
S00047-EN EH02 Rev. E  
Download from Www.Somanuals.com. All Manuals Search And Download.  
If the "530LTX" label is attached on the  
connector panel:  
Connection Type: Auto-Negotiation  
Network Address: (Blank)  
If the no label is attached on the connector panel:  
Connection Type: Auto-Sense  
Network Address: (Blank)  
When using Windows 2000 Server  
(1)Be sure to connect a mouse to the server.  
If you use the server without a mouse, the keyboard  
may become inoperative.  
(2)Installing Windows 2000 Server to the server  
with an MO device.  
Using an MO device with this server may prevent the  
correct installation of Windows 2000 Server. In this  
case, remove the MO device before installing  
Windows 2000 Server. As a precaution, replace the  
server’s panels before switching it on. For installing  
and removing the MO device, refer to MAGNIA  
User’s Guide (on the Documentation CD ROM),  
Chapter 2.  
3/15  
S00047-EN EH02 Rev. E  
Download from Www.Somanuals.com. All Manuals Search And Download.  
When using NetWare 5.1  
Follow the installation procedure described in the  
instruction manual to ensure that the installation is  
done properly.  
About expansion of optional RAID controller D  
When you use Server Setup Tool to setup the server  
with RAID controller D (MR466), the [Detailed Setup]  
option may not setup right. To set RAID configuration  
details with Server Setup Tool, use the following  
procedure.  
(1) When the message [Press <Ctrl><M> to Run  
MegaRAID Configuration Utility] is displayed during  
the server boot, press [Ctrl]+[M]. After MegaRAID  
Configuration Utility is started, set RAID  
configuration in detail, and select [Logical  
Drive]-[Advanced  
Menu]-[Write  
Policy],  
set  
[WRTHRU] to the array that is installed on the OS.  
For operation procedures about MegaRAID  
Configuration Utility, refer to MegaRAID User's  
manual.  
(2) After setting RAID configuration details, insert the  
Server Setup Tool CD-ROM and the Startup Disk  
floppy disk in the CD-ROM drive and the floppy disk  
drive respectively, then restart the system to start  
the Server Setup Tool.  
4/15  
S00047-EN EH02 Rev. E  
Download from Www.Somanuals.com. All Manuals Search And Download.  
(3) Open the Server Setup Tool [Main Menu], and click  
the [Setup] button to start setup wizard. When the  
[RAID Configuration screen] dialog box is displayed,  
check [Skip RAID Setup] check box, and continue  
the setup wizard. For setup wizard, refer to Server  
Setup Tool User's guide.  
(4) After setup, regarding the array that is installed on  
the OS, we recommend setting the logical drive's  
[Write Policy] setting to [WRBACK] using MegaRAID  
Configuration Utility or Power Console.  
Tape Attached to the CPU Heat Sink  
Protective tape is attached to the heat sink to prevent it  
separating from the CPU during transit. This protective  
tape need not be removed under normal conditions.  
However, you must remove it when you remove the  
CPU or heat sink.  
CAUTION  
Do not remove the tape immediately after turning off  
power, since the temperature of the CPU and  
surrounding parts are still high immediately after the  
power is turned off. When you reinstall the CPU or  
heat sink, there is no need to reattach the tape to the  
heat sink.  
5/15  
S00047-EN EH02 Rev. E  
Download from Www.Somanuals.com. All Manuals Search And Download.  
When attaching or removing the SCSI HDD/  
SCSI devices  
When attaching the side covers, take care to prevent  
the cables from being nipped between the side cover  
and the server.  
About expansion of optional SCSI Host Adapter  
SCI1105W/J, SCI1107A/W/J and SCI3900U  
An OS may not start depending on the connection.  
Perform the following setting for the SCSI host adapter  
not connected to an HDD starting OS.  
(1)In the BIOS screen of SCSI Host adapter during  
start of system, press[Ctrl] + [A] to enter the BIOS  
setting menu.  
(2)Select [Configure/View Host Adapter Setting] from  
the Options menu.  
(3)Select [Advanced Configuration Options] from the  
Additional Options menu.  
(4)Change the setting of [Host Adapter BIOS] of  
[Options Listed Below Have NO EFFECT if the BIOS  
is Disabled] from [Enabled] to [Disabled: scan bus].  
About an accuracy of the Real-time-clock (RTC)  
The RTC has a certain error, and the error is increased  
cumulatively if it is remained. To avoid the harmful  
influence for the operation, adjust the clock  
periodically.  
A clock adjustment is enabled with each OS and BIOS setup utility.  
For details of adjustment, refer to each manual.  
6/15  
S00047-EN EH02 Rev. E  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Components List  
Unpack and check components.  
If anything is missing, contact your dealer immediately.  
Save the packaging materials for possible future use.  
Components  
Quantity  
1
MAGNIA 510D  
Media  
Server Setup Tool (SST) CD-ROM  
Server Setup Tool (SST) Startup Disk  
LANDesk Server Manager (LDSM)  
(CD-ROM)  
(FD:1)  
1
1
(CD-ROM)  
1
MAGNIA 510D User’s Guide (Documentation CD ROM)  
1
Documentation  
MAGNIA 510D Read-Me-First Addendum(This document)  
1
Server Setup Tool (SST) User's Guide (Documentation CD ROM)  
1
Software License Agreement  
Warranty Booklet  
Keyboard  
1
1
1
Other  
Mouse  
1
Power Cable  
1
Screw and rails  
1set  
7/15  
S00047-EN EH02 Rev. E  
Download from Www.Somanuals.com. All Manuals Search And Download.  
733MHz P3 256K CPU Kit-LA / 866MHz P3 256K CPU Kit-LA / 1GHz P3 256K CPU Kit-L  
Read-Me-First  
Please read the following sheet before you start using CPU Kit-LA on MAGNIA 510D.  
1. About the system BIOS of MAGNIA510D  
Some CPU Kit-LA with maker S-Spec code cannot be used in MAGNIA 510D,  
which BIOS revision was before F6TJ.  
In this case, you must update your BIOS to latest revision.  
(A) Check your CPU Kit-LA’s maker S-Spec code by mark of CPU.  
R
Pentium !!! xxxxx  
XXXXXXXXXXXXXXX  
XXXXXXXX-XXXX SSSSS  
S-Spec code  
CPU Module  
UPG3141W  
UPG3142W UPG3143W  
(733MHz)  
(866MHz)  
(1BGHz)  
Stepping  
S-Spec  
B0  
C0 D0  
C0 D0  
C0 D0  
SL3X SL4 SL4Z SL4 SL4Z SL4 SL52  
Y
CG  
Yes  
Yes  
Yes  
L
CB  
Yes  
Yes  
Yes  
J
C8  
R
BIOS F4TJ  
Yes  
Yes  
Yes  
No  
No  
Yes  
No  
No  
Yes  
Yes  
Yes  
Yes  
No  
No  
Yes  
BIOS F5TJ  
BIOS F6TJ or  
later  
“No” : It is necessary to update the BIOS to F6TJ or to a later version.  
“Yes” : It is not necessary to update the BIOS.  
8/15  
S00047-EN EH02 Rev. E  
Download from Www.Somanuals.com. All Manuals Search And Download.  
(B) Check System BIOS revision by POST messages.  
American Release:xx/xx/xxxx  
Megatrends AMIBIOS (C) 1999 American Megatrends  
Inc.,  
6VXD7 XX XX  
Check System Health ok ,  
BIOS revision  
CPU ID:XXXX Patch ID:XXXX  
Pentium III XX-XXXMHz  
Check NVRAM…  
XXXXXKB OK  
Hit DEL if you want to run SETUP  
Wait…  
Press F1 to enter Dual BIOS Utility. Press ESC to quit  
( C ) American Megatrends Inc.,  
XX-XXXX-XXXXXX-XXXXXXXX-XXXXXX-XXXXXXXX-XX-XXXXXX-X  
(C) How to get the latest BIOS  
For the latest information and updates, please visit:  
(D) Install the CPU Kit-LA  
For detail, refer to your MAGNIA 510D User’s Guide (on the Documentation CD).  
2. In case of using Windows2000  
If the CPUs in your multiprocessor system are not at the same Stepping levels,  
Windows 2000 writes the following message to the Event Log. The MAGNIA series  
with mixed Stepping levels can be used together without any problem, so you can  
disregard the message.  
Event ID  
Message  
: 41  
:
The CPUs in this multiprocessor system are not all the same revision level.  
To use all processors the operating system restricts itself to the features of the least  
capable Processor in the system.  
Should occur with this system, contact the manufacturer to see if this mix of  
processors is supported.  
9/15  
S00047-EN EH02 Rev. E  
Download from Www.Somanuals.com. All Manuals Search And Download.  
[To view CPU Stepping levels on your computer]  
1. Click Start”, point to “Programs”, point to “Administrative” Tools, and then  
click “Computer Management”.  
2. Double-click the “System Information” folder, and then click the “System  
Summary” folder.  
Check the Processor line to view the CPU Stepping levels.  
B0 Stepping : x86 Family 6 Model 8 Stepping 3  
C0 Stepping : x86 Family 6 Model 8 Stepping 6  
D0 Stepping : x86 Family 6 Model 8 Stepping 10  
3. About the combination of D0-Stepping CPU and “LDSM6.1 with TOSHIBA  
Extension” in MAGNIA510D  
When combining D0-Stepping CPU and "LDSM6.1 with TOSHIBA Extension" in  
MAGNIA510D, it is necessary to install "LDSM6.1 with TOSHIBA Extension V6.2.1”  
or later.  
10/15  
S00047-EN EH02 Rev. E  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Contact Directory  
The List of contacts may change and not be necessarily complete because of the  
continuous launch of server. For updates of the contact information please refer to:  
Please also keep in mind that the warranty is only applicable to the country of first  
purchase.  
E.g if a server is sold by a German authorised dealer, the warranty is only valid in Germany.  
If you need service in another places than in the country of purchase please refer to your  
dealer for offers.  
Austria  
Toshiba Europe GmbH  
Handelskai 388  
1020 Wien  
Tel: 0800-220150  
Fax: +43-1-72031002  
Belgium  
Toshiba Information Systems (Belgium) S.A.N.V.  
Excelsiorlaan 40  
B - 1930 Zaventem  
Tel: +32-2-7158700  
Fax: +32-2-7253030  
Czech Republic  
CHG SERVICE, s.r.o.  
Vídenská 102  
619 00 Brno  
Tel: +420 5 4742 65-11 or -81  
Fax: +420 5 4742 65-13 or -90  
11/15  
S00047-EN EH02 Rev. E  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Denmark  
Toshiba Digital Media  
Naverland 27  
DK-2600  
Glostrup  
Tel: +45-3823 7600  
Fax: +45-3823 7601  
Finland  
Scribona TPC Oy / Toshiba Digital Media  
Sinimäentie 8 A  
PL 83 SF-02630  
Espoo  
Tel: +358-9 527 2555  
Fax: +358-9 527 2500  
France  
Toshiba Systemes (France) S.A.  
7, Rue Ampere; B.P. 131  
F - 92804  
Puteaux Cedex  
Tel: +33-1-4728-2929  
Fax: +33-1-4728-2247  
Germany  
Toshiba Europe GmbH  
Leibnizstrasse 2  
93055 Regensburg  
Tel: 0800-8737837  
Fax: +49-(0)941-7807-925  
BBS: +49-(0)941-7807-999  
ISDN1: +49-(0)781  
12/15  
S00047-EN EH02 Rev. E  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Greece  
IDEAL Electronics S.A.  
190 Syngrou Ave.  
176 71 Kalithea  
Tel: +30 - 1 - 95.62.551-4  
Fax: +30-1-95.79.094  
Ireland  
Toshiba Information Systems (U.K.) Limited (for Ireland)  
Toshiba Court: Addlestone Road  
KT15 2UL Weybridge, Surrey, UK  
Tel: +44-(0)1932-828828  
Fax: +44-(0)1932-822958  
BBS: +44-(0)1932-825127  
Italy  
Tel etc: provided with purchase of server  
Luxemburg  
Toshiba Inf. Systems Benelux B.V. (for Luxemburg)  
Rivium Boulevard 41  
NL - 2909 LK  
Capelle a/d IJssel  
Tel: +31-10-2882-300  
Fax: +31-10-2882-390  
Malta  
Tabone Computer Centre Limited  
111 Old Railway Track  
HMR-16 St Venera  
Tel: +356-49 36 04  
Fax: +356-49 36 03  
13/15  
S00047-EN EH02 Rev. E  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Netherlands  
Toshiba Inf. Systems Benelux  
Rivium Boulevard 41  
NL - 2909 LK Capelle a/d IJssel  
Tel: +31-10-2882-300  
Fax: +31-10-2882-390  
Norway  
Scribona Norway AS  
Stålfjæra 20  
P.O.Box 51/Kalbakken  
N-0901 Oslo  
Tel: +47-22-897000  
Fax: +47-22-897389  
Poland  
AC Serwis Sp. z o. o.  
ul. Partyzantów 71  
43-316 Bielsko-Biala  
Tel: +48-33-81 30-2 05  
Fax: +48-33-81 30-2 09  
Romania  
SCOP COMPUTERS SRL  
162 Barbu Vacarescu St  
Sector 2  
71424 Bucharest  
Tel: +40-1-2 31-46 02  
Fax: +40-1-2 31-46 06  
14/15  
S00047-EN EH02 Rev. E  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Spain  
Toshiba Inf. Systems (Espana) S.A.  
Parque Empresarial San Fernando  
Edificio Europa, 1a Planta, Escalera A  
E - 28831 Madrid  
Tel: +34-91-6606-700  
Fax: +34-91-6606-760  
Sweden  
Scribona Sweden AB  
P.O.Box 1374  
Sundbybergsvägen 1  
S-17127 Solna  
Tel: +46-200-212100  
Fax: +46-8-7344656  
United Kingdom  
Toshiba Information Systems (U.K.) Limited  
Toshiba Court  
Weybridge Business Park, Addlestone Road  
KT15 2UL Weybridge, Surrey  
Tel: +44-(0)1932-828828  
Fax: +44-(0)1932-822958  
BBS: +44-(0)1932-825127  
15/15  
S00047-EN EH02 Rev. E  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Teledex Network Card IP250DVoIP User Manual
Toshiba Computer Drive PX02SMF020 User Manual
Toshiba Personal Computer PSA20 User Manual
Toshiba TV DVD Combo 37HLV66 User Manual
Tricity Bendix Kitchen Entertainment Center CSIE500 User Manual
Uniden Cordless Telephone D1780 2 User Manual
ViewSonic Mouse KW208 User Manual
Vivitek Projector H9080FD User Manual
VocoPro Portable Speaker Voco user Manual portable speaker User Manual
VTech Stroller LITTLE SMART User Manual