Toshiba Security Camera IK WB70A User Manual

NETWORK CAMERA

Model:

IK-WB70A

User's Manual

For information on our latest products and peripheral devices, refer to the

following Website:

■ http://www.toshibasecurity.com

The above URL is subject to change without prior notice.

If the URL changes, refer to the Toshiba website (http://www.toshiba.com).

㪉㪍㩷㪆㩷㪈㪍㪇

Download from Www.Somanuals.com. All Manuals Search And Download.

Thank you for purchasing the IK-WB70A Network Camera. Before you start using

the camera, read this User's Manual carefully to ensure correct usage. Once you

have ﬁnished reading this User's Manual, keep it in a convenient place for future

reference.

The design, specifications, software, and User's Manual contents are subject to

change without prior notice.

Terms and Trademarks

● The term "OS" is used in this User's Manual to indicate operating systems

compatible with this product.

－ Windows^®XP: Microsoft^®Windows^®XP operating system

－ Windows Vista^®: Microsoft^®Windows Vista^®Business operating system

● The formal name of Windows^®is Microsoft^®Windows^®Operating System.

● Microsoft^®, Windows^®, and Windows Vista^®are trademarks or registered

trademarks of Microsoft^®Corporation in the United States and other countries.

● Adobe is a registered trademark and Adobe Reader is a trademark of Adobe

Systems Incorporated.

● Other product names appearing in this User's Manual may be trademarks or

registered trademarks of their respective holders.

NOTE

• This network camera might not operate correctly depending on the network environment.

㪉㪏㩷㪆㩷㪈㪍㪇

Download from Www.Somanuals.com. All Manuals Search And Download.

IMPORTANT SAFEGUARDS

1. Read Instructions

12. Lightning

Read all the safety and operating

instructions before operating the product.

2. Retain Instructions

For additional protection on this video

product during a lightning storm, or

when it is left unattended and unused

for long periods of time, unplug it from

the wall outlet and disconnect the

power supply and cable system. This will

prevent damage to the video product

due to lightning and power-line surges. If

lightning occurs, do not touch the unit or

any connected cables in order to avoid

electric shock.

Retain the safety instructions and user's

manual for future reference.

3. Warnings

Comply with all warnings on the product

and in the user's manual.

4. Follow Instructions

Follow all operating and use instructions.

5. Cleaning

13. Overloading

Disconnect this video product from the

power supply before cleaning.

6. Attachments

Do not overload the power supply or

extension cords as this can result in a

risk of ﬁre or electric shock.

Do not use attachments not

14. Object and Liquid Entry

recommended by the video product

manufacturer as they may cause hazards.

7. Accessories

Never push objects of any kind into this

video product through openings as they

may touch dangerous electrical points or

short-out parts that could result in a ﬁre

or electrical shock. Never spill liquid of

any kind on the video product.

Do not place this video product on an

unstable cart, stand, tripod, bracket

or table. The video product may fall,

causing serious injury to a person, or

serious damage to the product. Use

only with stand, tripod, bracket, or table

recommended by the manufacturer,

or sold with the video product. Any

mounting of the product should follow the

manufacturer's instructions, and should

use a mounting accessory recommended

by the manufacturer.

15. Servicing

Do not attempt to service this video

product yourself as opening or removing

covers may expose you to dangerous

electrical or other hazards. Refer all

servicing to qualiﬁed service personnel.

16. Damage Requiring service

Disconnect this video product from

the power supply and refer servicing to

qualiﬁed service personnel under the

following conditions.

8. Ventilation

This video product should never be

placed near or over a radiator or heat

in installation verify that there is proper

ventilation so that the camera temperature

operates within the recommended

temperature range.

a. When the power-supply cord or plug is

damaged.

b. If liquid has been spilled, or objects

have fallen into the video product.

c. If the video product has been

submerged in water.

9. Power Sources

d. If the video product does not operate

normally by following the operating

instructions in the user's manual.

Adjust only those controls that are

covered by the user's manual as an

improper adjustment of other controls

may result in damage and will often

require extensive work by a qualiﬁed

technician to restore the video product

to its normal operation.

This video product should be operated

only from the type of power source

indicated on the information label. If you

are not sure of the type of power supply

at your location, consult your product

dealer.

10. Power-Cord Protection

Power cords should be routed so that

they are not likely to be walked on or

pinched by items placed upon or against

them. Pay particular attention to cords at

plugs, screws and the point where they

exit the product.

e. If the video product has been dropped

or the cabinet has been damaged.

f. When the video product exhibiting a

distinct change in performance which

indicates a need for service.

11. Installation

17. Replacement Parts

Install this video product on a secure part

of the ceiling or wall. If installed on an

unsecured location, the camera could fall

causing injury and damage.

When replacing parts be sure the

service technician uses parts speciﬁed

by the manufacturer or have the same

characteristics as the original part.

Unauthorized substitutions may result in

ﬁre, electric shock or other hazards.

18. Safety Check

Upon completion of any service or repairs

to this video product, ask the service

technician to perform safety checks to

determine that the video product is in

proper operating condition.

㪉㪐㩷㪆㩷㪈㪍㪇

Download from Www.Somanuals.com. All Manuals Search And Download.

CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK.

DO NOT REMOVE COVER. NO USER SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle,

is intended to alert the user to the presence of uninsulated "dangerous

voltage" within the product's enclosure that may be of suﬃcient magnitude

to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the

user to the presence of important operating and maintenance (servicing)

instructions in the literature accompanying the appliance.

WARNING:

TO REDUCE THE RISK OF FIRE OR

ELECTRIC SHOCK, DO NOT

SUBMERGE THIS CAMERA IN

WATER.

FIELD INSTALLATION MARKING:

WORDED：“THIS INSTALLATION SHOULD BE MADE BY A QUALIFIED

SERVICE PERSON AND SHOULD CONFORM TO ALL LOCAL CODES.”

㪊㪇㩷㪆㩷㪈㪍㪇

Download from Www.Somanuals.com. All Manuals Search And Download.

NOTES ON USE AND INSTALLATION

• Do not aim the camera at the sun

Never aim the camera at the sun even with the camera power oﬀ.

• Do not shoot intense light

Intense light such as a spotlight may cause a bloom or smear. A vertical stripe

may appear on the screen. However, this is not a malfunction.

• Treat the camera with care

Dropping or subjecting the camera to intense vibration may cause it to

malfunction.

• Never touch internal parts

Do not touch the internal parts of the camera other than the parts speciﬁed.

• Do not submerge in water

The camera has some protection to water (see IP rating), and can be used indoors

or outdoors.

If the camera was submerged in water, turn oﬀ the power and contact your dealer.

• Keep the camera installation away from video noise

If cables are wired near electric lighting wires or a TV set, noise may appear in

images. In this event relocate cables or reinstall equipment.

• Check the ambient temperature and humidity

Avoid using the camera where the temperature is hotter or colder than the

speciﬁed operating range. Doing so could aﬀect the internal parts or cause the

image quality to deteriorate. Special care is required to use the camera at high

temperature and humidity.

• Should you notice any trouble

If any trouble occurs while you are using the camera, turn off the power and

contact your dealer. If you continue to use the camera when there is something

wrong with it, the trouble may get worse and an unpredictable problem may occur.

㪊㪈㩷㪆㩷㪈㪍㪇

Download from Www.Somanuals.com. All Manuals Search And Download.

Precautions for Use

Disclaimer

We disclaim any responsibility and shall be held harmless for any damages or losses

incurred by the user in any of the following cases:

1. Fire, earthquake or any other act of God; acts by third parties; misuse by the user,

whether intentional or accidental; use under extreme operating conditions.

2. Malfunction or non-function resulting in indirect, additional or consequential

damages, including but not limited to loss of expected income and suspension of

business activities.

3. Incorrect use not in compliance with instructions in this user's manual.

4. Malfunctions resulting from misconnection to other equipment.

5. Repairs or modiﬁcations made by the user or caused to be made by the user and

carried out by an unauthorized third party.

6. Notwithstanding the foregoing, Toshiba's liabilities shall not, in any circumstances,

exceed the purchase price of the product.

There may be a conﬂict with the Copyright Law and other laws when a customer

uses, displays, distributes, or exhibits an image picked up by the camera without

permission from the copyright holder. Please also note that transfer of an image

or ﬁle covered by copyright is restricted to use within the scope permitted by the

Protection of Personal Information

Images taken by the camera that reveal the likeness of an individual person may be

considered personal information. To disclose, exhibit or transmit those images over

the internet or otherwise, consent of the person may be required.

Usage Limitation

The product is not designed for any "critical applications." "Critical applications"

means life support systems, exhaust or smoke extraction applications, medical

applications, commercial aviation, mass transit applications, military applications,

homeland security applications, nuclear facilities or systems or any other

applications where product failure could lead to injury to persons or loss of life or

catastrophic property damage.

Accordingly, [Toshiba/TAIS] disclaims any and all liability arising out of the use of

the product in any critical applications.

㪊㪉㩷㪆㩷㪈㪍㪇

Download from Www.Somanuals.com. All Manuals Search And Download.

AC adapter

Be sure to use only the supplied AC adapter. Using a different AC adapter may

cause the camera to malfunction, heat up, or catch fire. Before using the AC

adapter, carefully read and observe the Important Safety Instructions ( → page 4)

and the notes below.

• Plug the AC adapter into the 100-240 VAC outlet.

If inserting it into other than 100-240 VAC outlet, it may result in electric shock

or ﬁre hazard.

• Do not repair, modify or disassemble the AC adapter. It may result in electric

shock or ﬁre hazard.

• Keep the blades of Plug free from any dust or dirt. Neglecting to do so may cause

a ﬁre due to deterioration of the insulation. Pull out the power plug from the outlet

before cleaning the blades.

• Do not cover or wrap the AC adapter with a cloth or place it near heating devices.

It may cause ﬁre or malfunction of the unit.

• Protect the power cord from being:

• damaged, modiﬁed for extension, or applied heat.

• pulled, put heavy objects, or pinched.

• bent, twisted extremely, or bundle.

Neglecting to do so may cause electric shock or ﬁre hazard.

• Do not expose this AC adapter to water.

• Install the AC adapter properly on a wall or ceiling after plugging in the AC

adapter. Avoid dropping the AC adapter, failing to do so may cause serious

personal injury or death.

• Do not allow the connectors on the AC adapter to come into contact with any

other metal object as this may result in short circuit.

• To connect the AC adapter, ﬁrmly insert the plug end of the cable into the AC

adapter jack. Do not insert the plug into other jacks as this may cause a malfunc-

tion.

• When removing the connection cable, disconnect the cable by holding its plug. Do

not disconnect the cable by pulling on the cable.

• Do not drop the AC adapter or subject it to strong impact.

• Do not use the AC adapter in hot and humid places.

• Do not use the supplied AC adapter with devices other than this camera.

• Temperature increasing on the surface of the adapter is normal. Before moving

the adapter to another location, unplug it from the wall outlet, and wait until its

temperature decreases.

• Buzzing noises may come from inside. This does not indicate malfunction.

• Using the AC adapter near a radio, TV, or cellphone may cause interference. Use

the adapter at suﬃcient distances from these devices.

• Be sure to use the supplied AC adapter. Using diﬀerent AC adapter may cause

ﬁre hazard or the camera to malfunction.

㪊㪊㩷㪆㩷㪈㪍㪇

Download from Www.Somanuals.com. All Manuals Search And Download.

Speciﬁcations

AC adapter (DSA-20P-10)

Power source

Rated output

: 100-240 VAC 50/60 Hz

: 12 VDC, 1.5 A

Ambient temperature guaranteed for performance

: 32°F to 104°F (0℃ to 40℃）

: -4°F to 140°F (-20℃ to 60℃）

Maximum external dimensions : 1.42

1.85 2.93 inches (36

Storage temperature

74.5 mm)

(width x height x depth)

: 72 inches (1828 mm)

Cord length

㪊㪋㩷㪆㩷㪈㪍㪇

Download from Www.Somanuals.com. All Manuals Search And Download.

Table of Contents

Introduction

● Introduction.......................................................................................................................................2

● IMPORTANT SAFEGUARDS.......................................................................................................4

● NOTES ON USE AND INSTALLATION....................................................................................6

● Precautions for Use.......................................................................................................................7

● AC adapter........................................................................................................................................8

● Table of Contents........................................................................................................................10

● Contents.........................................................................................................................................11

● Physical description...................................................................................................................12

Installation

● Installation......................................................................................................................................14

• Hardware installation ............................................................................................................................14

• Network deployment..............................................................................................................................15

• Software installation .............................................................................................................................18

● Initial Access to the Network Camera.................................................................................19

• Using web browsers..............................................................................................................................19

• Using 3GPP-compatible mobile devices........................................................................................21

How to Use

● Main Screen with Camera View..............................................................................................22

● Client Settings .............................................................................................................................26

Conﬁguration Deﬁnitions

● Conﬁguration Deﬁnitions..........................................................................................................28

• System parameters...............................................................................................................................28

• Security settings....................................................................................................................................30

• HTTPS........................................................................................................................................................31

• Network......................................................................................................................................................35

• DDNS..........................................................................................................................................................43

• Access List...............................................................................................................................................44

• Audio and video.......................................................................................................................................45

• Motion detection.....................................................................................................................................52

• Camera control........................................................................................................................................54

• Application ................................................................................................................................................57

• Recording ..................................................................................................................................................64

• System log................................................................................................................................................66

• View parameters.....................................................................................................................................66

• Maintenance.............................................................................................................................................67

Appendix

● Troubleshooting...........................................................................................................................71

• Status LED ...............................................................................................................................................71

• Reboot and restore ...............................................................................................................................71

• Audio ..........................................................................................................................................................71

• Wrong date and time.............................................................................................................................72

● Glossary (Index)............................................................................................................................73

● Speciﬁcations...............................................................................................................................75

● Appearance Diagram ...................................................................................................................76

㪊㪌㩷㪆㩷㪈㪍㪇

Download from Www.Somanuals.com. All Manuals Search And Download.

Contents

● IK-WB70A

● Shade

● Screws / RJ45 female/female

coupler

● Mounting bracket

Unused

● AC adapter

● Silica gel / Wrench

● I/O Connectors

● Quick Start Guide and Important

Safeguards

NETWORK CAMERA

Model: IK-WB70A

Quick Start Guide and Important Safeguards

This guide describes the hardware installation.

Refer the user's manual (PDF file) contained in the CD-ROM for settings,

operations and other information.

The application Adobe Reader is needed to see PDF ﬁles. If you do not have

this application, download it from the Website of Adobe Systems Incorporated.

For information on our latest products and peripheral devices, refer to the

following Website:

■

http://www.toshibasecurity.com

The above URL is subject to change without prior notice.

If the URL changes, refer to the Toshiba website (http://www.toshiba.com).

● Warranty

● CD-ROM

IK-WB70A

㪊㪍㩷㪆㩷㪈㪍㪇

Download from Www.Somanuals.com. All Manuals Search And Download.

Physical description

Front panel

Illuminance sensor

Lens

IR LED

Connectors

General I/O terminal block

Ethernet 10/100 RJ45 plug

Audio output (green) mini-jack

Microphone input (pink) mini-jack

Power cord socket (black)

GND

Cable length: approx. 39 inches (1000 mm)

General I/O Terminal Block

This Network Camera provides a general I/O terminal block which is used to connect

external input or output devices. The pin deﬁnitions are described below.

N.C.: No Connector

N.C.

485B

485A

AC24V

485B: RS485-

485A: RS485+

AC24V

AC24V: 24 VAC Power Input

GND: Ground

GND

DI :

Digital Input

DO :

Digital Output

+12V

+12V : 12 VDC Output

Name

Speciﬁcation

N.C.

No Connector

RS485-

RS485+

24 VAC Power Input

Ground

485B

485A

AC24V

GND

3.3 V

24 VAC ± 10 %

Digital Iutput

OPEN/Short-to-GND, isolation 2 kV

+12V

Digital Output

12 VDC Output

Max. 12 VDC, max. 400 mA, isolation 2 kV

12 VDC ± 10 %, max. 0.4A

㪊㪎㩷㪆㩷㪈㪍㪇

Download from Www.Somanuals.com. All Manuals Search And Download.

Alarm switch

1: +12 V 12 VDC Output

2: DO Digital Output

3: DI Digital Input

4: GND Ground

The connection deﬁnition is as below when "Digital input" is used for alarm input.

Internal Circuit

Signal Condition

Active state is low.

ꢄꢁꢄ8

8ꢃ+1

100 ms or more

12 V

ꢂ-

0 V

ꢂ-

+1ꢃ+0

Digital Input

Active state is high.

ꢀꢁꢂW(

100 ms or more

12 V

)0&

0 V

ꢄꢁꢄ8

8ꢃ+1

ꢂꢀ-

+1ꢃ176

Digital Output

MAX. 12 VDC, 400 mA

)0&

㪊㪏㩷㪆㩷㪈㪍㪇

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation

In this user's manual, "User" refers to whoever has access to the Network Camera,

and "Administrator" refers to the person who can conﬁgure the Network Camera and

grant user access to the camera.

Hardware installation

Please verify that your

LINK

product package contains

all the accessories listed in

the Package Contents listed

on page 11. Depending

on the user's application,

an Ethernet cable may be

needed. The Ethernet cable

should meet the specs of

UTP Category 5.

OLLI

ION

Connect the power adapter jack to the Network Camera before plugging in to

the power socket. This will reduce the risk of accidental electric shock.

Refer to the Quick Start Guide for details for hardware installation.

㪊㪐㩷㪆㩷㪈㪍㪇

Download from Www.Somanuals.com. All Manuals Search And Download.

Network deployment

Setup the Network Camera over the Internet

This section explains how to conﬁgure the Network Camera to an Internet connection.

1. If you have external devices such as sensors and alarms, make connection from

general I/O terminal block.

2. Use the supplied RJ45 female/female coupler to connect the Network Camera

to a network port via an Ethernet cable. Use Category 5 Cross Cable when the

Network Camera is directly connected to a PC.

3. Connect the power cord socket from the Network Camera to the supplied AC

adapter.

N.C.: No connection

N.C.

485B

485A

AC24V

LINK

ION

ITIO

485B: RS485-

485A: RS485+

AC24V: 24 VAC Power Input

Ethernet

switch/router

(not supplied)

GND: Ground

GND

DI : Digital Input

DO : Digital Output

+12V : 12 VDC Output

+12V

There are three ways to setup the Network Camera over the Internet. The ﬁrst way

is to setup the Network Camera behind a gateway. The second way is to utilize a

static IP. The third way is to use PPPoE.

Internet connection via a gateway

Before setting up the Network Camera over the Internet, make sure you have a

gateway and follow the steps below.

1. Connect your Network Camera behind a gateway, a network environment

example is illustrated as below. Regarding how to get your IP address, refer to

Software installation on page 18 for details.

WAN (Wide Area Network)

Router IP address : from ISP

IP address : 192.168.0.3

Subnet mask : 255.255.255.0

Default gateway : 192.168.0.1

LAN (Local Area Network)

Router IP address : 192.168.0.1

Cable or DSL Modem

IP address : 192.168.0.2

Subnet mask : 255.255.255.0

Default gateway : 192.168.0.1

㪋㪇㩷㪆㩷㪈㪍㪇

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation (Cont.)

2. In this case, if the Local Area Network (LAN) IP address of your Network Camera

is 192.168.0.3, please forward the following ports for the Network Camera on

the gateway.

■ HTTP port

■ RTSP port

■ RTP port for audio

■ RTCP port for audio

■ RTP port for video

■ RTCP port for video

If you have changed the port numbers on the Network page, please open the

ports accordingly on your gateway. For information on how to forward ports on the

gateway, please refer to the gateway user's manual.

3. Find out the public IP address of your gateway provided by your ISP (Internet

Service Provider). Use the public IP and the secondary HTTP port to access the

Network Camera from the Internet. Please refer to Network Type on page 35 for

details.

Internet connection with static IP

Choose this connection type if you are required to use a static IP for the Network

Camera and follow the steps below.

1. Set up the Network Camera in a LAN. Please refer to Software installation on

page 18 for details.

2. Go to Configuration > Network > Network Type. Select LAN > Use fixed IP

address.

3. Enter the static IP, Subnet mask, Default gateway, Primary DNS provided by

your ISP.

Internet connection via PPPoE (Point-to-Point over Ethernet)

Choose this connection type if you are connected to the Internet via a DSL Line.

Please refer to PPPoE on page 36 for details.

㪋㪈㩷㪆㩷㪈㪍㪇

Download from Www.Somanuals.com. All Manuals Search And Download.

Set up the Network Camera through Power over Ethernet

(PoE)

When using a PoE hub

The Network Camera is PoE-compliant, which allows it to be powered via a single

Ethernet cable. If your hub or gateway supports PoE, refer to the following illustration

to connect the Network Camera to a PoE hub/gateway via an Ethernet cable.

power + data transmission

LINK

OWE

COLL

ISION

ITION

PoE hub

(not supplied)

When using a non-PoE hub

If your hub or gateway does not support PoE, use a PoE power injector (not supplied)

to connect between the Network Camera and a non-PoE hub or gateway.

PoE power injector

(not supplied)

non-PoE hub

(not supplied)

LINK

OLL

ISION

TITIO

㪋㪉㩷㪆㩷㪈㪍㪇

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation (Cont.)

Software installation

Installation Wizard (IW), a free-bundled software packaged in the product CD, helps

to set up your Network Camera in a LAN.

1. Install the IW under the Software Utility directory from the

Installation

Wizard

software CD. Double click the IW shortcut on your desktop to

launch the program.

2. The program will analyze network environment. After your network environment is

analyzed, please click Next to continue the program.

3. The program will search for Network Cameras on the same LAN.

4. After searching, the main installer window will pop up. Click on the MAC and

model name which match the MAC attached the camera to connect to the

Network Camera.

0002D1714270

㪋㪊㩷㪆㩷㪈㪍㪇

Download from Www.Somanuals.com. All Manuals Search And Download.

Initial Access to the Network Camera

This chapter explains how to access the Network Camera through web browsers,

RTSP players, 3GPP-compatible mobile devices.

Using web browsers

1. Launch your web browser (ex. Microsoft^®Internet Explorer^®).

2. Enter the IP address of the Network Camera in the address ﬁeld. Press Enter.

3. The live video will be displayed in your web browser.

㪋㪋㩷㪆㩷㪈㪍㪇

Download from Www.Somanuals.com. All Manuals Search And Download.

Initial Access to the Network Camera (Cont.)

NOTE

● By default, the Network Camera is not password-protected. To prevent unauthorized

accesses, it is highly recommended to set a password for the Network Camera.

For more information about how to enable password protection, please refer to Security

Settings on page 30.

● If you see a warning message at initial access, click Install to install an ActiveX^®control

on your computer.

This page applies to

Windows^®XP. It is also

applicable for Windows

Vista^®Business.

● If you see a dialog box indicating that your security settings prohibit running ActiveX^®

controls, please enable your ActiveX^®controls for your browser.

1. Choose Tools > Internet Options > Security > Custom Level.

2. Look for Download signed ActiveX^®controls; select Enable or Prompt. Click OK.

㪋㪌㩷㪆㩷㪈㪍㪇

Download from Www.Somanuals.com. All Manuals Search And Download.

Using 3GPP-compatible mobile devices

To view the streaming media through 3GPP-compatible mobile devices, make sure

the Network Camera can be accessed from the Internet. For more information on

how to set up the Network Camera over the Internet, refer to Setup the Network

Camera over the Internet on page 15.

To utilize this feature, check the following settings on your Network Camera:

1. Because most players on 3GPP mobile phones do not support RTSP

authentication, make sure the authentication mode of RTSP streaming is set to

disable. For more information, refer to RTSP Streaming on page 41.

2. As the 3G network bandwidth is limited, you can not use large video size. Set

the video and audio streaming parameters as listed below.

For more information, refer to Audio and video on page 45.

Video Mode

Frame size

Maximum frame rate

Intra frame period

Video quality (Constant bit rate)

Audio type (GSM-AMR)

MPEG-4

176 x 144

5 fps

1 S

40 kbps

12.2 kbps

3. As most ISP and players only support port number 554 to allow RTSP streaming

to go through, set the RTSP port to 554.For more information, refer to RTSP

Streaming on page 41.

4. Launch the players on 3GPP-compatible mobile devices.

Type the URL commands in the player.

The format is rtsp://<public ip address of your camera>:<rtsp port>/<access

name for stream1 or stream2>.

㪋㪍㩷㪆㩷㪈㪍㪇

Download from Www.Somanuals.com. All Manuals Search And Download.

Main Screen with Camera View

This chapter explains the layout of the main page. It is composed of the following

four sections:

Toshiba logo, Menu, Camera Name, and Live Video Window.

Toshiba logo

Camera name

Live view window

Toshiba Logo

Click this logo to visit the Toshiba website.

Snapshot: Click this button to capture and save still images. The captured images

will be displayed in a pop-up window. Right-click the image and choose Save Picture

As to save it in JPEG (*.jpg) or BMP (*.bmp) format.

Conﬁguration: Click this button to access the Network Camera conﬁguration page.

It is suggested that a password is applied to the Network Camera so that only the

administrator can conﬁgure the Network Camera. For more information, please refer

to Conﬁguration Deﬁnitions on page 28.

Client Settings: Click this button to access the client setting page. For more

information, refer to Client Settings on page 26.

Digital Output: Click this button to turn the digital output device on or oﬀ.

Camera Name

The camera name can be customized. For more information, refer to System

Parameters on page 28.

㪋㪎㩷㪆㩷㪈㪍㪇

Download from Www.Somanuals.com. All Manuals Search And Download.

Live Video Window

The following window is displayed when the video mode is set to MPEG-4:

MPEG-4 protocol and media options

Video title

Title, time and date

IK-WB70A(TCP-AV)

Time and date

IP7142 16:38:01 2008/01/03

Video and audio

control buttons

Video title: The video title can be conﬁgured. For more information, refer to Video

settings on page 45.

Time and date: Display the current time. For more information, refer to Video

settings on page 45.

Title, time and date: Video title, time and date can be stamped on the streaming

video. For more information, refer to Video settings on page 45.

MPEG-4 protocol and media options: The transmission protocol and media

options for MPEG-4 video streaming. For more information, refer to Client Settings

on page 26.

Video and audio control buttons: Depending on the Network Camera model and

Network Camera conﬁguration, some buttons may not be available.

Digital zoom edit: Deselect Disable digital zoom to enable the zoom operation.

The navigation screen indicates which part of the image is being magnified. To

control the zoom level, drag the slider bar. To move to a diﬀerent area you want to

magnify, drag the navigation screen.

Start MP4 recording: Click this button to record video clips in MP4 ﬁle format

to your computer. Press the

Stop MP4 recording button to end recording. When

you quit the web browser, video recording stops accordingly. To specify the storage

destination and the ﬁle name, please refer to MP4 Saving Options on page 27 for

details.

Talk: Click this button to talk to people around the Network Camera. Audio will

come out from the external speaker connected to the Network Camera.

Pause: Pause the transmission of streaming media. The button becomes

Resume button after clicking the Pause button.

㪋㪏㩷㪆㩷㪈㪍㪇

Download from Www.Somanuals.com. All Manuals Search And Download.

Main Screen with Camera View (Cont.)

Resume: Resume the transmission of streaming media. The button becomes

Pause button after clicking the Resume button.

Stop: Stop the transmission of streaming media. Click the

continue transmission.

Resume button to

Volume: When the

mute function is not activated, move the slider bar to

adjust the volume at the client computer.

Mute: Turn oﬀ the

volume at the client computer.

Mic Volume: When the

mute function is not activated, move the slider bar to

adjust the microphone volume at the client computer.

Mute: Turn oﬀ the

microphone volume at the client computer.

The following window is displayed when the video mode is set to MJPEG:

IK-WB70A

Video title

Title, time and date

Time and date

GATE 10:11:50 2008/01/09

Video control

buttons

Video title: The video title can be conﬁgured. For more information, refer to Video

settings on page 45.

Time and date: Displays the current time and date. For more information, refer to

Video settings on page 45.

Title, time and date: Video title time and date can be stamped on the streaming

video. For more information, refer to Video settings on page 45.

Video and audio control buttons: Depending on the Network Camera model and　

Network Camera conﬁguration, some buttons may not be available.

Digital zoom edit: Deselect Disable digital zoom to enable the zoom operation.

The navigation screen indicates which part of the image is being magnified. To

control the zoom level, drag the slider bar. To move to a diﬀerent area you want to

magnify, drag the navigation screen.

㪋㪐㩷㪆㩷㪈㪍㪇

Download from Www.Somanuals.com. All Manuals Search And Download.

Start MP4 recording: Click this button to record video clips in MP4 ﬁle format

to your computer. Press the Stop MP4 recording button to end recording. When

you quit the web browser, video recording　stops accordingly. To specify the storage

destination and the ﬁle name, refer to MP4 Saving Options on page 27 for details.

Talk: Click this button to talk to people around the Network Camera. Audio will

come out from the external speaker connected to the Network Camera.

Mic Volume: When the

mute function is not activated, move the slider bar to

adjust the microphone volume at the client computer.

Mute: Turn oﬀ the microphone volume at the client computer.

㪌㪇㩷㪆㩷㪈㪍㪇

Download from Www.Somanuals.com. All Manuals Search And Download.

Client Settings

This chapter explains how to select the streaming source, transmission mode and

saving options at the client computer. It is composed of the following four sections:

Stream Options, MPEG-4 Media Options, MPEG-4 Protocol Options and MP4 Saving

Options. When completed with the settings on this page, click Save on the bottom

of the page to take eﬀect.

Stream Options

The Network Camera supports MPEG-4 and MJPEG dual streams. For more

information, refer to Video settings on page 45.

MPEG-4 Media Options

Select to stream video or audio data. This works only when the video mode is set to

MPEG-4.

MPEG-4 Protocol Options

Depending on your network environment, there are four transmission modes of

MPEG-4 streaming:

UDP unicast: This protocol allows for more real-time audio and video streams.

However, network packets may be lost due to network burst traffic and images

may be broken. Activate UDP connection when occasions require time-sensitive

responses and the video quality is less important. Note that each unicast client

connecting to the server takes up additional bandwidth and the Network Camera

allows up to ten simultaneous clients.

UDP multicast: This protocol allows multicast-enabled routers to forward network

packets to all clients requesting streaming media. This helps to reduce the network

transmission load of the Network Camera while serving multiple clients at the same

time. Note that to utilize this feature, the Network Camera must be configured

to enable multicast streaming at the same time. For more information, see RTSP

Streaming on page 41.

㪌㪈㩷㪆㩷㪈㪍㪇

Download from Www.Somanuals.com. All Manuals Search And Download.

TCP: This protocol guarantees the complete delivery of streaming data and thus

provides better video quality. The downside with this protocol is that its real-time

eﬀect is not as good as that of the UDP protocol.

HTTP: This protocol allows the same quality as TCP protocol and you do not need

to open speciﬁc port for streaming under some network environments. Users inside

a ﬁrewall can utilize this protocol to allow streaming data to come through.

MP4 Saving Options

Users can record the live video as they are watching it by clicking

Start MP4

Recording on the main page. Here, you can specify the storage destination and ﬁle

name.

Folder: Specify a storage destination for the recorded video ﬁles.

File Name Preﬁx: Enter the text that will be put in front of the video ﬁle name.

Add date and time suﬃx to the ﬁle name: Select this option to add date and time

to the ﬁle name suﬃx.

CLIP_20090327-140744

Date and time sufﬁx

The format is: YYYYMMDD_HHMMSS

File name preﬁx

㪌㪉㩷㪆㩷㪈㪍㪇

Download from Www.Somanuals.com. All Manuals Search And Download.

Conﬁguration Deﬁnitions

Only Administrators can access the system conﬁguration page. Each category in

the menu will be explained in the following sections.

System Parameters

This section explains how to conﬁgure the basic settings for the Network. It contains

the following three segments: System, System Time and DI/DO. After completing

the settings on this page, click Save on the bottom of the page to take eﬀect.

System

Camera name: Enter a name for the Network Camera. The camera name will be

displayed at the top of the main page.

System Time

㪌㪊㩷㪆㩷㪈㪍㪇

Download from Www.Somanuals.com. All Manuals Search And Download.

Enable Daylight Saving Time: Select this option to enable daylight savings time

(DST). During DST, the system clock moves one hour ahead. Set the time zone for

your Network Camera ﬁrst if using this feature. The starting time and ending time of

the DST is displayed upon selecting this option. To manually conﬁgure the daylight

saving time rules, refer to Upload or Export Daylight Saving Time Conﬁguration File

on page 68 for details.

Time zone: Set your local time zone from the drop-down list.

Keep current date and time: Select this option to keep the current date and time

of the Network Camera. The Network Camera's internal real-time clock maintains the

date and time even when the power of the system is turned oﬀ.

Sync with computer time: Select this option to synchronize the date and time of

the Network Camera with the client computer. The read-only date and time of the PC

is displayed.

Manual: The administrator can enter the date and time manually. The date and time

format are [yyyy/mm/dd] and [hh:mm:ss].

Automatic: The Network Time Protocol is a service that synchronizes computer

clocks by periodically querying an NTP Server.

NTP server: Assign the IP address or domain name of the time-server. Leaving the

text box blank connects the Network Camera to the default time-servers.

Update interval: Select to update the time with the NTP server on hourly, daily,

weekly, or monthly basis.

DI and DO

Digital input: Select High or Low to deﬁne normal status of the digital input. The

Network Camera will report the current status.

Digital output: Select Grounded or Open to define normal status of the digital

output. The Network Camera will show whether the trigger is activated or not.

㪌㪋㩷㪆㩷㪈㪍㪇

Download from Www.Somanuals.com. All Manuals Search And Download.

Conﬁguration Deﬁnitions (Cont.)

Security Settings

This section explains how to enable password protection and create multiple

accounts. It contains the following three segments: Root Password, Add User and

Manage User.

Root Password

The administrator account“root”is permanent and can not be deleted. To add more

accounts, you must apply a password for the“root”account ﬁrst.

1. Type the identical password in both text boxes.

2. Click Save to enable password protection.

3. A log in window is displayed for authentication; type the administrator's name

and password to access the Network Camera.

Add User

Administrators can add up to twenty user accounts.

1. Input the new user's name and password.

2. Select the desired security level. Click Add to take eﬀect.

Access rights are sorted by account types. There are three kinds of account types.

• Administrator: can access all pages and use all URL Commands.

• Operator: can access only the main page and use some URL Commands.

• Viewer: can access only the main page and not use any URL Commands.

Manage User

Here you can change user's access rights or delete user accounts.

1. Pull down the user list to ﬁnd an account.

2. Make necessary changes and then click Save or Delete to take eﬀect.

㪌㪌㩷㪆㩷㪈㪍㪇

Download from Www.Somanuals.com. All Manuals Search And Download.

HTTPS

This section explains how to enable authentication and encrypted communication

over SSL.

Enable HTTPS

Select this options to turn on the HTTPS communications.

Select either“HTTP & HTTPS”or“HTTPS only.”

Select the method to create a certiﬁcate before clicking Save.

㪌㪍㩷㪆㩷㪈㪍㪇

Download from Www.Somanuals.com. All Manuals Search And Download.

Conﬁguration Deﬁnitions (Cont.)

Create and Install Certiﬁcate

Select either to create a self-signed certiﬁcate or a signed certiﬁcate.

To create a self-signed certiﬁcate automatically.

1. Click“Create self-signed certiﬁcate automatically.”

2. Click Save.

To create a self-signed certiﬁcate manually.

1. Click“Create self-signed certificate manually”. The Create Certificate window

will pop up.

2. Fill in the information required for generating a Certiﬁcate Signed Request (CSR)

and click Save.

3. Click Save.

To install a trusted create certiﬁcate.

1. Click“Create certiﬁcate request and install”. The Create Certiﬁcate window will

pop up.

㪌㪎㩷㪆㩷㪈㪍㪇

Download from Www.Somanuals.com. All Manuals Search And Download.

2. Fill in the information required for generating a Certiﬁcate Signed Request (CSR)

and click Save.

3. Here is an example of a CSR:

4. Click Save.

Certiﬁcate Information

Display the certiﬁcate information. Users may click Property for details. To remove

the signed certificated, uncheck the Enable HTTPS secure connection and click

Remove.

㪌㪏㩷㪆㩷㪈㪍㪇

Download from Www.Somanuals.com. All Manuals Search And Download.

Conﬁguration Deﬁnitions (Cont.)

Security Alert

Fig.1

Fig.2

Above security alert may be shown when switch between HTTP and HTTPS

connection. Click OK or Yes to continue the operation.

Fig.3

Fig.4

Above security alert may be shown when accessing the camera by HTTPS using

“Self-Signed Certiﬁcate”,

IE7: Click“Continue to this website (not recommended)”on Fig.3 to continue the

operation.

IE6: Click Yes on Fig.4 to continue the operation.

㪌㪐㩷㪆㩷㪈㪍㪇

Download from Www.Somanuals.com. All Manuals Search And Download.

Network

This section explains how to conﬁgure wired network connection for the Network

Camera. It consists the following five segments: Network Type, HTTP, Two way

audio, FTP and RTSP Streaming. After completing the settings on this page, click

Save to take eﬀect.

Network Type

LAN

Select this option when the Network Camera is deployed in a local area network (LAN)

and is intended to be accessed by local computers.

Get IP address automatically: Select this option to obtain a dynamic IP address

assigned by a DHCP server each time the camera is connected to the LAN.

Use ﬁxed IP address: Select this option to manually assign a static IP address to

the Network Camera. Please refer to Internet connection with static IP on page 16

for details.

Enable UPnP presentation: Select this option to enable UPnP^TMpresentation

for your Network Camera so that whenever a Network Camera is presented to the

LAN, shortcuts of connected Network Cameras will be listed in My Network Places.

Currently, UPnP^TMis supported by Windows XP or later. To use this feature, verify

that the UPnP^TMcomponent is installed on your computer.

Enable UPnP port forwarding: To access the Network Camera from the Internet,

select this option to allow the Network Camera to open ports on the gateway

automatically so that video streams can be sent out from a LAN. To utilize of this

feature, verify that your gateway supports UPnP^TMand activated.

㪍㪇㩷㪆㩷㪈㪍㪇

Download from Www.Somanuals.com. All Manuals Search And Download.

Conﬁguration Deﬁnitions (Cont.)

PPPoE (Point-to-point over Ethernet)

Select this option to conﬁgure your Network Camera to make it accessible from a DSL

Internet connection. To use this feature, requires an account provided by your ISP.

Follow the steps below to acquire your Network Camera's public IP address.

1. Set up the Network Camera in a LAN.

2. Go to Conﬁguration > Application > Server Settings (refer to Server Settings on

page 59) to add a new server -- email or FTP server.

3. Go to Conﬁguration > Application > Media Settings (refer to Media Settings on

page 57). Select System log so that you will receive a list of system log in TXT

ﬁle format which contains the Network Camera's public IP address in your email

or on the FTP server.

4. Go to Conﬁguration > Network > Network Type. Select PPPoE and enter the

user name and password provided by your ISP. Click Save to take eﬀect.

5. The Network Camera will to reboot.

6. After the camera reboots, disconnect power from the Network Camera. Move the

ethernet connection from the LAN to the DSL modem.

NOTE

● If the default ports are already used by other device connecting to the same gateway, the

Network Camera will select other ports for the Network Camera.

● If UPnP^TMis not supported by your gateway, you will see the following message.

● Steps to enable UPnP^TMuser interface on your computer:

Note that you must log on to the computer as a system administrator to install the

UPnP^TMcomponents.

1. Go to Start, click Control Panel, and then click Network Connections.

㪍㪈㩷㪆㩷㪈㪍㪇

Download from Www.Somanuals.com. All Manuals Search And Download.

2. Click the Optional Network Components in the menu bar's Advanced.

3. In the Windows Components Wizard dialog box, select Networking Services and

then click Details.

4. In the Networking Services dialog box, select Universal Plug and Play and then

click OK.

5. Click Next in the following window.

6. UPnP^TMis enabled.

㪍㪉㩷㪆㩷㪈㪍㪇

Download from Www.Somanuals.com. All Manuals Search And Download.

Conﬁguration Deﬁnitions (Cont.)

● How does UPnP^TMwork?

UPnP^TMnetworking technology provides automatic IP conﬁguration and dynamic discovery

of devices added to a network. Services and capabilities oﬀered by networked devices,

such as printing and ﬁle sharing, are available among each other without bothersome

network conﬁguration. In the case of Network Cameras, you will see Network Camera

shortcuts at My Network Places.

● Enabling UPnP port forwarding allows the Network Camera to open secondary HTTP

port on the gateway, not HTTP port 80, meaning that you have to add the secondary

HTTP port number behind the Network Camera's public address in order to access the

Network Camera from the Internet. For example, when the HTTP port is set to 80 and the

secondary HTTP port is set to 8080, refer to the list below for the Network Camera's IP

address.

From the Internet

In a LAN

http://203.67.124.123 : 8080

http://192.168.4.160 or

http://192.168.4.160 : 8080

● If the PPPoE settings are incorrectly conﬁgured or the Internet access is not working,

restore the Network Camera to factory default; refer to Restore on page 67 for details.

After the Network Camera is reset to factory default, it is accessible in a LAN.

HTTP

Authentication: Depending on your network security requirements, the Network

Camera provides two types of security settings for a HTTP transaction: basic and

digest. If basic authentication is selected, the password is sent in plain text format;

there can be potential risks of being intercepted. If digest authentication is selected,

user credentials are encrypted in MD5 algorithm and thus provide better protection

against unauthorized accesses.

HTTP port or Secondary HTTP port: By default, the HTTP port is set to 80 and

the secondary HTTP port is set to 8080. Also, they can be assigned with another

port number between 1025 and 65535. If the ports are incorrectly assigned, the

following warning messages are displayed:

㪍㪊㩷㪆㩷㪈㪍㪇

Download from Www.Somanuals.com. All Manuals Search And Download.

To access the Network Camera within a LAN, both HTTP port and secondary HTTP

port can be used to access the Network Camera. For example, when the HTTP port

is set to 80 and the secondary HTTP port is set to 8080, refer to the list below for

the Network Camera's IP address.

In a LAN

http://192.168.4.160 or

http://192.168.4.160 : 8080

NOTE

● To use HTTP authentication, make sure that there is set a password for the Network

Camera ﬁrst; refer to Security Settings on page 30 for details.

HTTPS

By default, the HTTPS port is set to 443. It can be assigned with another port

number between 1025 and 65535.

Two way audio

By default, the two way audio port is set to 5060. It can be assigned with another

port number between 1025 and 65535.

The Network Camera supports two way audio communication so that operators can

transmit and receive audio simultaneously. By using the Network Camera's built-

in microphone and an external speaker, you can communicate with people near the

Network Camera.

㪍㪋㩷㪆㩷㪈㪍㪇

Download from Www.Somanuals.com. All Manuals Search And Download.

Conﬁguration Deﬁnitions (Cont.)

Note that as JPEG only transmits a series of JPEG images to the client, to use this

feature, make sure the video mode is set to“MPEG-4”and the media option is set

to“Video and Audio”.

Audio send to operators

America

Audio send from operators

Taiwan

Audio is being transmitted to the Network Camera

IK-WB70A(TCP-AV)

Talk button

Mute

Microphone volume

Click

to enable audio transmission to the Network Camera; click

to adjust the

volume of microphone; click

to turn oﬀ the audio. To stop talking, click again.

FTP

The FTP server allows the Network Camera to use the Toshiba Installation Wizard

to upgrade ﬁrmware. By default, the FTP port is set to 21. It can be assigned with

another port number between 1025 and 65535.

㪍㪌㩷㪆㩷㪈㪍㪇

Download from Www.Somanuals.com. All Manuals Search And Download.

RTSP Streaming

Authentication: Depending on your network security requirements, the Network

Camera provides three types of security settings for streaming via RTSP protocol:

disable, basic and digest. If basic authentication is selected, the password is sent

in plain text format; there can be potential risks of being intercepted. If digest

authentication is selected, user credentials are encrypted in MD5 algorithm and

thus provide better protection against unauthorized accesses.

Access name for stream 1 or Access name for stream 2: The access name is

used to diﬀerentiate the streaming source. When using an RTSP player (e.g. Quick

time) to access the Network Camera, and the video mode is set to MPEG-4, use the

following RTSP URL command to request a transmission of streaming data.

rtsp://<ip address>:<rtsp port>/<access name for stream1 or stream2>

For example, when the access name for stream 1 is set to live sdp:

1. Launch a RTSP player

2. Choose File > Open URL. An URL dialog box will pop up.

3. Type the URL command in the text box.

RTSP port or RTP port for video, audio/ RTCP port for video, audio

The RTSP (Real-Time Streaming Protocol) controls the delivery of streaming media.

By default, the port number is set to 554.

The RTP (Real-time Transport Protocol) is used to deliver video and audio data to

the clients. By default, the RTP port for video is set to 5556 and the RTP port for

audio is set to 5558.

The RTCP (Real-time Transport Control Protocol) allows the Network Camera to

transmit the data by monitoring Internet traﬃc volume. By default, the RTCP port for

video is set to 5557 and the RTCP port for audio is set to 5559.

㪍㪍㩷㪆㩷㪈㪍㪇

Download from Www.Somanuals.com. All Manuals Search And Download.

Conﬁguration Deﬁnitions (Cont.)

The ﬁve ports can be changed between 1025 and 65535. The RTP port must be

an even number and the RTCP port is RTP port number plus one, and thus always be

odd. When the RTP port changes, the RTCP port will change accordingly.

If the RTP ports are incorrectly assigned, the following warning message is

displayed:

Multicast settings for stream 1 or Multicast settings for stream 2: Selecting

the Always multicast enables Network Camera to transmit the multicast packets.

Unicast video transmission delivers a stream through point-to-point transmission;

multicast, on the other hand, sends a stream to the multicast group address and

allows multiple clients to acquire the stream by requesting a copy from the Multicast

group address.

The multicast RTP port must be an even number and the multicast RTCP port

number is the multicast RTP port number plus one, and thus it is always be odd.

When the multicast RTP port changes, the multicast RTCP port will change

accordingly. These ports can be changed between 1025 and 65535.

If the multicast RTP video ports are incorrectly assigned, the following warning

message is displayed:

Multicast TTL [1 ～ 255]:The multicast TTL (Time to live) is the value that tells the

gateway the range a packet can be forwarded.

NOTE

● To use the RTSP streaming authentication, make sure that your have set a password for

the Network Camera ﬁrst; refer to Security Settings on page 30 for details.

㪍㪎㩷㪆㩷㪈㪍㪇

Download from Www.Somanuals.com. All Manuals Search And Download.

DDNS

This section explains how to configure dynamic domain name service for the

Network Camera. DDNS is a service that allows your Network Camera, especially

when assigned with a dynamic IP address, to have a ﬁxed host and domain name.

DDNS: Dynamic domain name service

Enable DDNS: Select this option to enable the DDNS setting.

“Provider”The provider list contains seven hosts that provide DDNS services.

Please connect to the service provider's web site to review the service charges and

sign-up for the service if you want to use DDNS.

ChangeIP.com

http://www.changeip.com/toshiba/

No-IP.com

http://www.no-ip.com/ext/toshiba.php

“Camera Name”If the User wants to use a DDNS service, enter the camera name

that is registered at the DDNS server.

“User name”The User Name ﬁ eld is necessary for logging into the DDNS server or

to notify the User of the new IP address.

Note: When this ﬁ eld is input as“User Name”, the following ﬁ eld must be input as

“Password”.

“Password”Input the password to access the DDNS service.

“Save”Click on this button to save current settings for the DDNS service.

㪍㪏㩷㪆㩷㪈㪍㪇

Download from Www.Somanuals.com. All Manuals Search And Download.

Conﬁguration Deﬁnitions (Cont.)

Access list

This section explains how to control the access permission by checking the client

PC's IP addresses. It contains of the following four segments: Allowed list, Denied

list, Delete allowed list, and Delete denied list.

Allowed list or Denied list

There are two lists for permission control: Allowed list and Denied list. Only those

clients whose IP addresses are in the Allowed list and not in the Denied list can

access the Network Camera.

1. In the Allowed list or Denied list column, type the starting IP address and ending

IP address in the text boxes. A total of ten lists can be configured for both

columns.

2. Click Add to take eﬀect.

NOTE

● For example, when the range of the allowed list is set from 1.1.1.0 to 192. 255. 255. 255

and the range of the denied list is set from 1.1.1.0 to 170. 255. 255. 255, Only users' IP

located between 171.0.0.0 and 192. 255. 255. 255 can access the Network Camera.

Denied

List

Allowed

List

Delete allowed list / Delete denied list

1. In the Delete allowed list or Delete denied list, select a list from the drop-down list.

2. Click Delete to take eﬀect.

㪍㪐㩷㪆㩷㪈㪍㪇

Download from Www.Somanuals.com. All Manuals Search And Download.

Audio and video

This section explains how to coﬁgure audio and video performances of the Network

Camera. It contains the following two segments: Video settings and Audio settings.

Video settings

Video title: Enter a name that will be displayed on the title bar of the live video.

IK-WB70A(TCP-AV)

Color: Select to display color or black/white video streams.

Power line frequency: Set the power line frequency to match the local electricity

settings to eliminate image ﬂickering associated with ﬂuorescent lights. Note that

after the power line frequency is changed, it is required to disconnect and reconnect

the power cord of the Network Camera in order for the new setting to take eﬀect.

㪎㪇㩷㪆㩷㪈㪍㪇

Download from Www.Somanuals.com. All Manuals Search And Download.

Conﬁguration Deﬁnitions (Cont.)

Video orientation: Flip--vertically reflect the display of the live video; Mirror--

horizontally reﬂect the display of the live video. Select both options if the Network

Camera is installed upside-down to correct the image orientation.

White balance: Adjust the value for best color temperature.

■ Auto

The Network Camera automatically adjusts the color temperature of light in

response to diﬀerent light sources. The white balance setting defaults to Auto

and works well in most situations.

■ Keep current value

Follow the steps below to manually set the white balance to compensate for the

ambient lighting conditions.

1. Set the White balance to Manual.

2. Place a sheet of white paper in front of the lens; then allow the Network Camera

to adjust the color temperature automatically.

Exposure Time: 1/30 S, 1/15 S, and 1/5 S.

Overlay title and time stamp on video: Select this option to place the video title

and time on video streams. When the frame size is set to 176 x 144 as the right

picture below, only time will be stamped on video streams.

IK-WB70A(TCP-AV)

Image Settings

Click Image Settings to open the Image Settings page. In this page, you can tune

Brightness, Saturation, Contrast, and Hue for video compensation. Each ﬁeld has

eleven levels ranged from -5 to +5. The value 0 indicates default auto tuning.

You can click Preview to ﬁne-tune the image, or click Restore to recall the original

settings without incorporating the changes. When completed with the settings on

this page, click Save to take eﬀect and click Close to quit the page.

㪎㪈㩷㪆㩷㪈㪍㪇

Download from Www.Somanuals.com. All Manuals Search And Download.

Privacy mask

Click Privacy Mask to open the Privacy Mask page. In this page, you can block out

some sensitive zones for privacy concerns.

IK-WB70A

■ To set the privacy mask windows, follow the steps below:

1. Click New to add a new window.

2. To resize and drag-drop the window, which is recommended to be at least twice

the size of the object (height and width) you want to cover.

3. Enter a descriptive Window Name and click Save to take eﬀect.

4. Select Enable privacy mask to enable this function.

NOTE

● Up to 5 privacy mask windows can be set in the same screen.

● If you want to delete the window, please click on the‘x’at the upper right-hand corner of

the window to close the window.

Sensor Settings

Click Sensor Settings to open the Sensor Settings page. In this page, you can set

the exposure level, AGC, WDR (Wide Dynamic Range), night mode, and IR cut ﬁlter.

㪎㪉㩷㪆㩷㪈㪍㪇

Download from Www.Somanuals.com. All Manuals Search And Download.

Conﬁguration Deﬁnitions (Cont.)

Exposure level: You can manually set the Exposure level from 1 to 8. The default

value is 4.

AGC (Auto Gain Control): You can manually set the AGC level to 2X, 4X or 8X.

The default value is 4X.

Enable WDR (Wide Dynamic Range):

Select to enable the WDR function. This Network Camera with WDR feature can

cope with very challenging lighting conditions. It is capable of capturing both of the

dark part and bright part of a target and combining the diﬀerences into a scene to

generate a highly realistic image as the human eyes can see.

If this function is selected the exposure level and AGC function will be disabled.

Switch to B/W in night mode: Select it to enable the Network Camera to

automatically switch to B/W in night mode.

IR cut ﬁlter:

The Network Camera has the ability to automatically remove the IR cut ﬁlter and

turn on the IR illuminators during night or low light conditions.

■ Auto

The Network Camera automatically removes the filter by sensing the level of

ambient light.

■ Schedule mode

The Network Camera switches between day mode and night mode based on

speciﬁed schedule. Enter the starting time and ending time for the day mode. The

time format is [hh:mm] and is expressed in 24-hour clock time. By default, the

starting time and ending time of day mode are set to 07:00 and 18:00.

■ Day mode

In day mode, the Network Camera switches on the IR cut ﬁlter at all times to block

the infrared light from reaching the sensor so that the colors will not be distorted.

■ Night mode

In night mode, the Network Camera switches oﬀ (remove) the IR cut ﬁlter to allow

the infrared light to pass through. This improves the sensitivity of the Network

Camera in low-light conditions.

You can click Preview to ﬁne-tune the image, or click Restore to recall the original

settings without incorporating the changes. After completing the settings on this

page, click Save to take eﬀect and click Close to quit the page.

Video quality settings for stream 1 or stream 2: You can set up two separate

streams for the Network Camera for diﬀerent viewing devices. For example, set the

Network Camera to a smaller frame size and a lower bit rate for remote viewing on

mobile phones. Or, set the Network Camera to a larger video size and a higher bit

rate for live viewing on web browsers.

㪎㪊㩷㪆㩷㪈㪍㪇

Download from Www.Somanuals.com. All Manuals Search And Download.

■ Mode

The Network Camera oﬀers two choices of video compression standards for real-

time viewing: MPEG-4 and MJPEG.

If MPEG-4 is selected, it is streamed in RTSP or HTTP. There are four dependent

parameters provided in MPEG-4 mode for video performance adjustment.

■ Frame size

Select the video size. A larger frame size takes up more bandwidth. The frame

sizes are selectable in the following resolutions: 176 x 144, 352 x 240 and 640

x 480.

■ Maximum frame rate

This limits the maximal refresh frame rate per second. Set the frame rate higher

for a smoother video update.

If the power line frequency is set to 50Hz, the frame rates are selectable at the

following rates: 1fps, 2fps, 3fps, 5fps, 8fps, 10fps, 15fps, 20fps and 25fps. If

the power line frequency is set to 60Hz, the frame rates are selectable at the

following rates: 1fps, 2fps, 3fps, 5fps, 8fps, 10fps, 15fps, 20fps, 25fps and

30fps.

■ Intra frame period

Determine how often to plant an I frame. The shorter the duration, the more likely

you will get a better video update, but at the cost of higher network bandwidth

consumption. Select the intra frame period from the following duration: 1/4

second, 1/2 second, 1 second, 2 seconds, 3 seconds and 4 seconds.

■ Video quality

A complex scene generally produces larger file size, meaning that higher

bandwidth will be needed for data transmission. Therefore, if Constant bit rate is

selected, the bandwidth utilization is ﬁxed at a selected level, resulting in mutable

video quality performances. The bit rates are selectable at the following rates:

20Kbps, 30Kbps, 40Kbps, 50Kbps, 64Kbps, 128Kbps, 256Kbps, 512Kbps,

768Kbps, 1Mbps, 2Mbps, 3Mbps and 4Mbps.

On the other hand, if Fixed quality is selected, all frames are transmitted with the

same quality; bandwidth utilization is therefore unpredictable. The video qualities

are selectable at the following settings:

Medium, Standard, Good, Detailed and Excellent.

㪎㪋㩷㪆㩷㪈㪍㪇

Download from Www.Somanuals.com. All Manuals Search And Download.

Conﬁguration Deﬁnitions (Cont.)

If JPEG mode is selected, the Network Camera continuously sends JPEG images to

the clients, producing dynamic eﬀects similar to movies. Every single JPEG image

transmitted guarantees the same image quality, which in turn comes at the expense

of variable bandwidth usage. And because the media contents are a combination of

JPEG images, no audio data is transmitted to the clients.

■ Frame size

Select the video size. Note that a larger frame size takes up more bandwidth. The

frame sizes are selectable in the following resolutions: 176 x 144, 352 x 240

and 640 x 480.

■ Maximum frame rate

This limits the maximal refresh frame rate per second. Set the frame rate higher

for a smoother video update.

If the power line frequency is set to 50Hz, the frame rates are selectable at the

following rates: 1fps, 2fps, 3fps, 5fps, 8fps, 10fps, 15fps, 20fps and 25fps. If

the power line frequency is set to 60Hz, the frame rates are selectable at the

following rates: 1fps, 2fps, 3fps, 5fps, 8fps, 10fps, 15fps, 20fps, 25fps and

30fps.

■ Video quality

The video qualities are selectable at the following settings: Medium, Standard,

Good, Detailed and Excellent.

Disable IR LED:

If you don't want to let others know that the network camera is on, you can select

this option to turn oﬀ the LED illuminators. This will prevent the Network Camera's

operation from being noticed.

㪎㪌㩷㪆㩷㪈㪍㪇

Download from Www.Somanuals.com. All Manuals Search And Download.

Audio settings

Mute: Select this option to disable audio transmission from the Network Camera

to all clients. Note that if mute mode is turned on, no audio data will be transmitted

to all clients even though the audio transmission is enabled in the Client Settings

page. In that case, the following message is displayed.

Input gain: The input gain are selectable at the folowing settings:

-34.5 dB, -33 dB, -31.5 dB, -30 dB, -28.5 dB, -27 dB, -25.5 dB, -24 dB, -22.5 dB,

-21 dB, -19.5 dB, -18 dB, -16.5 dB, -15 dB, -13.5 dB, -12 dB, -10.5 dB, -9 dB, -7.5

dB, -6 dB, -4.5 dB, -3 dB, -1.5 dB, 0 dB, +1.5 dB, +3 dB, +4.5 dB, +6 dB, +7.5 dB,

+9 dB, +10.5 dB, +12 dB.

Audio type : Select audio codec AAC or GSM-AMR and the bit rate

• AAC targets at performing good sound quality at the cost of higher bandwidth

consumption. The bit rates are selectable at the following rates: 16Kbps, 32Kbps,

48Kbps, 64Kbps, 96Kbps and128Kbps

• GSM-ARM is designed to optimize speech quality and requires less bandwidth.

The bit rates are selectable at the following rates: 4.75Kbps, 5.15Kbps,

5.90Kbps, 6.7Kbps, 7.4Kbps, 7.95Kbps, 10.2Kbps and 12.2Kbps.

When completed with the settings on this page, click Save to take eﬀect.

㪎㪍㩷㪆㩷㪈㪍㪇

Download from Www.Somanuals.com. All Manuals Search And Download.

Conﬁguration Deﬁnitions (Cont.)

Motion detection

This section explains how to configure the Network Camera to enable motion

detection. A total of three motion detection windows can be conﬁgured.

IK-WB70A(TCP-AV)

To enable motion detection, follow the steps below:

1. Click New to add a new motion detection window.

2. In the Window Name text box, enter a descriptive name for the motion detection

window.

■ To move and resize the window, drag-drop the window.

■ To delete window, click X at top right of the window.

3. Deﬁne the sensitivity to moving objects and the space ratio of all alerted pixels

by moving the Sensitivity and Percentage slider bar.

4. Click Save to take eﬀect.

5. Select Enable motion detection to enable this function.

For example:

IK-WB70A(TCP-AV)

The Percentage Indicator will rise or fall depending on the image variation. When

motions are detected by the Network Camera and are judged to exceed the deﬁned

threshold, a red bar rises. Meanwhile, the motion detection window will be outlined

in red. Photos or videos can be captured instantly and conﬁgured to send to the

remote server (Email, FTP) by using this feature as a trigger source. For more

information on how to plot an event, refer to Application on page 57.

㪎㪎㩷㪆㩷㪈㪍㪇

Download from Www.Somanuals.com. All Manuals Search And Download.

A green bar indicates that even though motions are detected, the event will not be

triggered because the image variations are still falling under the deﬁned threshold.

Percentage = 30%

NOTE

● How does motion detection work?

There are two parameters for setting the motion detection: Sensitivity and Percentage. In

the illustration above, frame A and frame B are two sequential images. Pixel diﬀerences

between the two frames are detected and highlighted in gray (frame C), and will be

compared with the sensitivity setting. Sensitivity is a value that expresses the sensitivity

to moving objects. Higher sensitivity settings are expected to sense a slight movement

while smaller sensitivity settings tend to neglect it. When the sensitivity is set to 70%,

the Network Camera deﬁnes the pixels in the purple areas as "alerted pixels" (frame D).

Percentage is a value that expresses the proportion of "alerted pixels" to all pixels in the

motion detection window. In this case, 50% of pixels are identiﬁed as "alerted pixels".

When the percentage is set to 30%, the motions are judged to exceed the deﬁned

threshold; therefore, the motion window will be outlined in red.

For applications that require higher security management, it is suggested to set higher

sensitivity settings and smaller percentage values.

㪎㪏㩷㪆㩷㪈㪍㪇

Download from Www.Somanuals.com. All Manuals Search And Download.

Conﬁguration Deﬁnitions (Cont.)

Camera control

This section explains how to control the Network Camera's digital zoom and optional

pan/tilt unit or scanner using RS485 interface.

RS485 Settings

Disable: Select this option to disable this function.

PTZ camera: Select this option to enable PTZ operation.

To use this feature, ﬁrst connect the Network Camera with a PTZ Unit or scanner

via RS485 interface. Then conﬁgure the PTZ driver and RS485 port settings in the

following diagram.

Toshiba offers Pelco D protocol and others. If none of the above PTZ drivers is

supported by your PTZ scanner, select Custom camera (scanner). Refer to the

user's manual of your PTZ scanner to set the Camera ID, PTZ driver, and Port

settings. The Camera ID is necessary for multiple cameras control. If you select

PTZ camera and click Save to enable this function, the camera control panel will be

displayed in the main page as the following diagram:

㪎㪐㩷㪆㩷㪈㪍㪇

Download from Www.Somanuals.com. All Manuals Search And Download.

Preset Position

Click Preset Position to open the Preset Position page. In this page, you can set

the preset position for the Network Camera. A total of 20 preset positions can be

conﬁgured.

IK-WB70A(TCP-AV)

Follow the steps below to set preset positions:

1. Adjust the Network Camera to a desired position with the buttons on the right

side of the window.

2. In the Preset position name text box, enter a descriptive name for the preset

position. The preset position name allows up to forty characters. Click Add to

take eﬀect. The preset position name will appear in the Preset Positions drop-

down list. To remove a preset position from the list, select a preset position

name from the Preset Positions drop-down list and then click Delete.

3. You can click“Go to”to aim at preset positions, which will also displayed in the

main page.

4. Click Save to take eﬀect.

Custom Command

If the Custom camera (scanner) is selected as the PTZ driver, the PTZ control

panel on the main page will not take effect. You need to configure command

buttons to control the PTZ scanner. Click Custom Command to open the

Custom Command page. A total of ﬁve command buttons can be conﬁgured.

Refer to the user's manual of your PTZ scanner to enter the command in the

following blanks.

Click Save to enable the settings and click Close to quit the page.

㪏㪇㩷㪆㩷㪈㪍㪇

Download from Www.Somanuals.com. All Manuals Search And Download.

Conﬁguration Deﬁnitions (Cont.)

The command button will appear in the main page as the following diagram.

㪏㪈㩷㪆㩷㪈㪍㪇

Download from Www.Somanuals.com. All Manuals Search And Download.

Application

This section explains how to conﬁgure the Network Camera to react in response

to particular situations. A typical application is that when a motion is detected,

the Network Camera sends buffered images to an FTP server or via Email as

notiﬁcations.

In the illustation on the right side, an

event can be triggered by many sources,

such as motion detection or external

digital input devices. When an event

is triggered, you can specify what kind

of action will be performed. You can

configure the Network Camera to send

snapshots or videos to your email address

or FTP site.

Action

Event Trigger

ex. Motion detection,

Periodically, Digital input,

System reboot

Media

Server

(what to send)

(where to send)

ex. Snapshot, Video Clips

ex. Email, FTP

To start plotting an event, it is suggested to conﬁgure server and media segments

ﬁrst so that the Network Camera will know what action to perform when a trigger is

activated.

Media Settings

In Media Settings column, click Add to open the media setting page. In this page,

you can specify what kind of media to send when a trigger is activated. A total of

ﬁve media settings can be conﬁgured.

㪏㪉㩷㪆㩷㪈㪍㪇

Download from Www.Somanuals.com. All Manuals Search And Download.

Conﬁguration Deﬁnitions (Cont.)

Media name: Enter a descriptive name for the media setting.

Media Type: There are three choices of media types available: Snapshot, Video Clip,

and System log.

Snapshot: Select to send snapshots when a trigger is activated.

■ Source: Select to take snapshots from stream 1 or stream 2.

■ Send [#] pre-event images

The Network Camera has a buﬀer area; it temporarily holds data up to a certain

limit. Specify to capture how many images before a trigger is activated. Up to

seven images can be generated.

■ Send [#] post-event images

Specify to capture how many images after a trigger is activated. Up to seven

images can be generated. For example, if both the Send pre-event images and

Send post-event images are set to seven, a total of ﬁfteen images are generated

after a trigger is activated.

1 pic. 2 pic. 3 pic. 4 pic. 5 pic.

6 pic.

7 pic. 8 pic. 9 pic. 10 pic. 11 pic. 10 pic. 12 pic. 13 pic. 14 pic. 15 pic.

The moment the trigger

is activated.

■ File Name Preﬁx

Enter the text for the ﬁle name.

Snapshot20090327_140744

■ Add date and time suﬃx to the ﬁle name

Select this option to add date and time to the ﬁle

name suﬃx.

File name preﬁx

Date and time sufﬁx

The format is: YYYYMMDD_HHMMSS

For example:

Video Clip: Select to send video clips when a trigger is activated.

■ Source: Select to record video clips from stream 1 or stream 2.

■ Pre-event recording

The Network Camera has a buﬀer area; it temporarily holds data up to a certain

limit. Specify to record video clips for how many seconds before a trigger is

activated. Up to nine seconds can be set.

■ Maximum duration

Specify the maximal recording duration in seconds. Up to ten seconds can be set.

For example, if the Pre-event recording is set to ﬁve seconds and the Maximum

duration is set to ten seconds, the Network Camera continues to record for

another four seconds after a trigger is activated.

1 sec. 2 sec. 3 sec. 4 sec. 5 sec. 6 sec. 7 sec. 8 sec. 9 sec. 10 sec.

The moment the trigger

is activated.

㪏㪊㩷㪆㩷㪈㪍㪇

Download from Www.Somanuals.com. All Manuals Search And Download.

■ Maximum ﬁle size

Video20090327_140744

Specify the maximal ﬁle size allowed.

File name preﬁx

Date and time sufﬁx

The format is: YYYYMMDD_HHMMSS

■ File Name Preﬁx

Enter the text for the ﬁle name.

For example:

System log: Select to send a system log when a trigger is activated.

When completed, click Save to take eﬀect and then click Close to quit this page.

The new media name will appear in the media drop-down list on the Application

page as below. To remove a media setting from the list, select a media name from

the drop-down list and then click Delete. Only when the media setting is not being

applied to an event setting‚ can it be deleted.

Server Settings

In the Server column, click Add to open the server setting page. In this page, you

can specify where the notiﬁcation messages will be sent when a trigger is activated.

A total of ﬁve server settings can be conﬁgured.

㪏㪋㩷㪆㩷㪈㪍㪇

Download from Www.Somanuals.com. All Manuals Search And Download.

Conﬁguration Deﬁnitions (Cont.)

Server name: Enter a descriptive name for the server setting.

Server Type: There are four choices of server types available: Email, FTP, HTTP,

and Network storage.

Email: Select to send the media via Email when a trigger is activated.

■ Sender email address: Enter the email address of the sender.

■ Recipient email address: Enter the email address of the recipient.

■ Server address: Enter the domain name or IP address of the email server.

■ User name: Enter the user name of the email account.

■ Password: Enter the password of the email account.

To verify if the email settings are correctly conﬁgured, click Test. The result will be

shown in a pop-up window. If it works, you will also receive an email indicating the

result.

FTP: Select to send the media to an FTP server when a trigger is activated.

■ Server address: Enter the domain name or IP address of the FTP server.

■ Server port

By default, the FTP port server is set to 21. Also, it can be assigned with another

port number between 1025 and 65535.

■ User name: Enter the login name of the FTP account.

■ Password: Enter the password of the FTP account.

■ Remote folder name

Enter a folder to place the media file. If the folder name does not exist, the

Network Camera will create one on the FTP server.

■ Passive Mode

Most ﬁrewalls do not accept new connections initiated from external requests. If

the FTP server supports passive mode, select this option to enable passive mode

FTP and allow data transmission to pass through the ﬁrewall.

To verify if the FTP settings are correctly conﬁgured, click Test. The result will be

shown in a pop-up window. If it works, you will also receive a test.txt ﬁle on the FTP

server.

㪏㪌㩷㪆㩷㪈㪍㪇

Download from Www.Somanuals.com. All Manuals Search And Download.

HTTP: Select to send the media to an HTTP server when a trigger is activated.

■ URL: Enter the URL of the HTTP server.

■ User name: Enter the user name.

■ Password: Enter the password.

To verify if the HTTP settings are correctly conﬁgured, click Test. The result will be

shown in a pop-up window. If it works, you will also receive a test.txt ﬁle on the HTTP

server.

Network storage: Select to send the media to a network storage when a trigger is

activated.

■ Network storage location: Enter the path of the network storage.

■ Workgroup: Enter the workgroup for network storage.

■ User name: Enter the user name.

■ Password: Enter the password.

To verify if the network storage settings are correctly conﬁgured, click Test. The

result will be shown in a pop-up window. If it works, you will also receive a test.txt ﬁle

on the network storage server.

When completed, click Save to take eﬀect and then click Close to quit this page.

The new server name will appear in the server drop-down list on the application

page as below. To remove a server setting from the list, select a server name from

the drop-down list and then click Delete. Only when the server setting is not being

applied to an event setting can it be deleted.

㪏㪍㩷㪆㩷㪈㪍㪇

Download from Www.Somanuals.com. All Manuals Search And Download.

Conﬁguration Deﬁnitions (Cont.)

Event

In the Event section, click Add to open the event setting page. In this page, you can

arrange the three elements -- Trigger, Schedule and Action to plot an event. A total

of three event settings can be conﬁgured.

Event name: Enter a descriptive name for the event setting.

Enable this event: Select this option to enable this event setting.

Priority: Select the relative importance of this event (High, Normal, and Low).

Events with higher priority setting will be executed ﬁrst.

Detect next event after [#] seconds: Enter the duration in seconds to pause

continuous motion detection after a motion is detected and a continuous DI after a DI.

An event is an action initiated by user-defined trigger source; it is the causal

arrangement of the following three elements: Trigger, Event Schedule, and Action.

Trigger: Deﬁnes the source by which an event is caused. The trigger source can be

conﬁgured to use the Network Camera's built-in motion detection system or external

digital input devices.There are four choices of trigger sources:

■ Video motion detection

Select this option to allow the Network Camera to use the built-in motion

detection system as a trigger source. To enable this function, you need to

conﬁgure Motion detection ﬁrst. For more information, refer to Motion detection

on page 52 for details.

■ Periodically

Select this option to allow the Network Camera to trigger periodically for every

other deﬁned minute. At most 999 minutes can be set.

■ Digital input

Select one of the Digital inputs to allow the Network Camera to use external

digital input device as a trigger source.

㪏㪎㩷㪆㩷㪈㪍㪇

Download from Www.Somanuals.com. All Manuals Search And Download.

■ System boot

Select this option to allow the Network Camera to trigger when the power of

Network Camera is disconnected.

Event Schedule: The eﬀective period in which the event stays active. Specify the

eﬀective period for the event.

■ Select the days on weekly basis.

■ Select the time for recording in 24-hour time format.

Action: Also referred as the effect, defines the action to be performed by the

Network Camera when the trigger is activated. Select the action to perform when a

trigger is activated.

■ Trigger digital output for [#] seconds

Select this option to turn on external digital output device when a trigger is

activated. Specify the length of trigger interval in the text box.

■ Server name and Media name

Select the server and media name to allow the Network Camera to send the

media ﬁles to the server when a trigger is activated. The server name is a name

speciﬁed on the server setting page.

The media name is a name speciﬁed on the media setting page and listed in the

drop-down list.

When completed, select Enable this event. Click Save to take eﬀect and then click

Close to quit this page. The new event name will appear in the event drop-down list

on the application page. To remove an event setting from the list, select an event

name from the drop-down list and then click Delete.

㪏㪏㩷㪆㩷㪈㪍㪇

Download from Www.Somanuals.com. All Manuals Search And Download.

Conﬁguration Deﬁnitions (Cont.)

Recording

This section explains how to configure the recording settings for the Network

Camera.

Recording Settings

Click Add to open the recording setting page. In this page, you can define the

recording source, recording schedule and recording capacity. A total of two

recording settings can be conﬁgured.

Recording name: Enter a descriptive name for the recording setting.

Enable this recording: Select this option to enable video recording.

Priority: Select the relative importance of this recording setting (High, Normal, and

Low).

Source: Select the recording source (stream 1 or stream 2).

Recording Schedule: Specify the recording duration.

■ Select the days on weekly basis.

■ Select the time for recording in 24-hour time format.

㪏㪐㩷㪆㩷㪈㪍㪇

Download from Www.Somanuals.com. All Manuals Search And Download.

Destination: Specify a storage destination for the recorded video ﬁles. Note that

the destination ﬁeld is empty by default. Go to Conﬁguration > Application > Server

Settings to set a Network storage server; refer to Server Settings on page 59.

Max. recording capacity: When the maximum capacity is reached, the oldest ﬁle

will be overwritten by the latest one.

File size for each recording: Specify the ﬁle size for each recording media.

File name preﬁx: Enter the text that will be put in front of the ﬁle name.

When completed, select Enable this recording. Click Save to take eﬀect and then

click Close to quit this page. The new recording name will appear in the recording

drop-down list on the recording page. To remove a recording setting from the list,

select a recording name from the drop-down list then and click Delete.

㪐㪇㩷㪆㩷㪈㪍㪇

Download from Www.Somanuals.com. All Manuals Search And Download.

Conﬁguration Deﬁnitions (Cont.)

System log

This section explains how to configure the Network Camera to send the system

log message to a remote server and how to refer the current log message of the

Network Camera.

It is composed of the following two Segments: Remote Log and Current Log.

Remote Log

You can configure the Network Camera to send the system log file to a remote

server as a log message.

When using this feature, the appropriate syslog server is required for receiving the

system log message from the Network Camera.

Follow the steps below to set up the remote log:

1. In the IP address text box, enter the IP address of the remote server.

2. In the port text box, enter the port number of the remote server.

3. When completed, select Enable remote log and click Save to take eﬀect.

Current Log

This column displays the system's log in chronological order. The system log is

stored in the Network Camera's buﬀer area and will be overwritten when reaching a

certain amount.

The system log messages stored in the Network Camera will be all cleared after

reboot or power down the Network Camera.

View parameters

The View parameters page lists the entire system's parameters in alphabetical

order. If you need technical assistance, please provide the information listed in this

page.

㪐㪈㩷㪆㩷㪈㪍㪇

Download from Www.Somanuals.com. All Manuals Search And Download.

Maintenance

This chapter explains how to restore the Network Camera to factory default, upgrade

ﬁrmware version, etc.

Reboot

This feature allows you to turn oﬀ and then turn on the Network Camera. It takes

about one ～ two minutes to complete the process. When completed, the live video

will be displayed in your browser. The following message is displayed during the

rebooting process.

If the connection fails after rebooting, manually enter the IP address of the Network

Camera in the address ﬁeld to resume the connection.

Restore

This feature allows you to restore the Network Camera to factory default. Two

settings can be excluded:

Network Type: Select this option to retain the Network Type settings (please refer

to Network Type on page 35).

Daylight Saving Time: Select this option to retain the Daylight Saving Time

settings (refer to System Parameters on page 28)

If none of the options is selected, all settings will be restored to factory default.

The following message is displayed during the restoring process.

㪐㪉㩷㪆㩷㪈㪍㪇

Download from Www.Somanuals.com. All Manuals Search And Download.

Conﬁguration Deﬁnitions (Cont.)

Upload or Export Daylight Saving Time Conﬁguration File

This feature allows you to set the starting time and ending time of DST.

Follow the steps below to set up:

1. In the Export Daylight Saving Time Configuration File column, click Export to

export an Extensible Markup Language (*.xml) ﬁle from the Network Camera.

2. Edit the XML ﬁle and locate your time zone; set the starting time and ending

time of the DST. When completed, save the ﬁle.

In the example below, the DST begins each year at 2:00 a.m. on the second Sunday

in March and ends at 2:00 a.m. on the ﬁrst Sunday in November.

㪐㪊㩷㪆㩷㪈㪍㪇

Download from Www.Somanuals.com. All Manuals Search And Download.

3. In the Upload Column, click Browse... and specify the XML ﬁle.

If the incorrect date and time is assigned, you will see the following warning

message when uploading the ﬁle to the Network Camera.

4. Click Upload. To enable the DST, see System Time on page 28.

The following message is displayed when attempting to upload an incorrect ﬁle

format.

Upgrade Firmware

This feature allows you to upgrade the ﬁrmware on your Network Camera. It takes

about ﬁve minutes to complete the process.

Do not power oﬀ the Network Camera during the upgrade.

Follow the steps below to upgrade ﬁrmware:

1. Download a new ﬁrmware ﬁle from Toshiba website. The ﬁle is in pkg ﬁle format.

2. Click Browse... and specify the ﬁrmware ﬁle.

3. Click Upgrade. The Network Camera starts to upgrade and will reboot

automatically when the upgrade completes.

㪐㪋㩷㪆㩷㪈㪍㪇

Download from Www.Somanuals.com. All Manuals Search And Download.

Conﬁguration Deﬁnitions (Cont.)

The upgrade is successful as you see "Reboot system now!! This connection will

close". After that, re-access the Network Camera.

The following message is displayed when the upgrade is succeeded.

The following message is displayed when you have selected an incorrect ﬁrmware

ﬁle.

Starting firmware upgrade...

Do not power down the server during the upgrade.

The server will restart automatically after the upgrade is

completed.

It will takes about 1 - 5 minutes.

Wrong PKG file format

Unpack fail

㪐㪌㩷㪆㩷㪈㪍㪇

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting

Status LED

The LED indicates the status of the Network Camera.

Status LED

Description

Blinking red

(two short, one long)

1. Power is being supplied to the Network Camera.

2. Restore, or reboot the Network Camera.

Reboot and restore

Reset button

Status LED

There is a reset button on the inner side of the Network Camera. It is used to reboot

the Network Camera or restore the Network Camera to factory default. Sometimes

rebooting the Network Camera could set the Network Camera back to normal state.

If the problems remain after rebooting, restore the Network Camera to factory

default and install again.

Reboot: Press and release the reset button. The status LED will blink two short one

long in red.

Restore: Press the reset button continuously for over 5 seconds until the status

LED blinks two short one long in red. Note that all settings will be restored to factory

default.

Restoring the factory defaults will erase any previous settings.

Audio

When using multiple network cameras, restart Internet Explorer each time you switch

the camera. Using the same Internet Explorer for the multiple cameras may transmit

multiple camera's audio.

㪐㪍㩷㪆㩷㪈㪍㪇

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting (Cont.)

Wrong date and time

If this Network Camera is left in the low-temperature environment, the date and

time of camera may be delayed when turning on the power. To prevent this trouble,

it is highly recommended to leave the power ON of Network Camera in the low-

temperature environment.

㪐㪎㩷㪆㩷㪈㪍㪇

Download from Www.Somanuals.com. All Manuals Search And Download.

Glossary (Index)

Default gateway ...................................... 16, 35

Network devices cannot communicate

directly with devices in other networks.

In this case, communication becomes

possible by using devices like a router.

Accessories ...................................................... 11

Access list ......................................................... 44

Administrator .................................................... 30

Alarm setting .................................................... 52

Audio output ...................................................... 12

Audio setting .................................................... 51

Default gateway is the IP address of the

router.

DHCP ................................................................... 35

(Dynamic Host Conﬁguration Protocol)

This is the protocol to assign IP address

dynamically to each client on TCP/IP

network. DHCP server controls information

of IP address, gateway address, domain

name and subnet mask and can assign

these to client.

Browser .................................................................. 3

Software to browse Web screens.

Microsoft^®Corporation Internet Explorer^TM

only.

Digital In/Out .................................................... 29

(Digital input/output)

Digital zoom ....................................................... 23

DNS ...................................................................... 16

(Domain Name System)

Camera control ................................................. 54

The network camera's Pan/Tilt/Zoom

operation by connecting with a PTZ driver

or scanner via RS485 interface.

Domain Name Systems translates IP

addresses into names making it easier to

manage hosts.

Camera name .................................................... 28

Certiﬁcate .......................................................... 32

This is a certificate for HTTPS. There

are a self-signed certiﬁcate and a signed

certiﬁcate. The certiﬁcate can be created

by using the network camera.

Ethernet cable .................................................. 17

E-mail ................................................................... 60

Conﬁguration ..................................................... 28

Contents ............................................................. 11

Firmware ............................................................. 69

Program to run this product. It is installed

in the ﬂash memory, and can be updated

from PC by using PC upload function of

the WEB.

Daylight Saving Time (DST)................. 29, 67

This network camera automatically

configure the Daylight Saving Time.

Clicking Export to export an XML ﬁle from

the network camera allows you to set the

starting and ending time of DST.

Frame rate .................................................. 49, 50

The rate of number of pictures that are

translated in a second.

DDNS ................................................................... 43

(Dynamic Domain Name System)

Frame size .................................................. 49, 50

FTP ....................................................................... 40

(File Transfer Protocol)

This is the technique to overwrite the

information of DNS（Domain Name

System）server dynamically and forward

only different informations between DNS

servers.

A protocol to transfer file(s) to and from

other network devices. The network

camera supports both active.

Because of this, it enables to reduce

forwarding data which are needed to renew

information of DNS server, and reduce

overhead of the network. When combined

with DHCP (Dynamic Host Configuration

Protocol), it is possible to assign IP

address and host name right away as the

host on the LAN changes.

HTTP port number ........................................... 38

HTTPS.................................................................. 31

It enables authentication and encrypted

communication to protect streaming data

over the Internet.

㪐㪏㩷㪆㩷㪈㪍㪇

Download from Www.Somanuals.com. All Manuals Search And Download.

Glossary (Index) (Cont.)

Image settings ................................................. 46

Installation Wizard .......Quick Start Guide: 16

I/O terminal block ............................................. 12

IP address .......................................................... 35

Recording ........................................................... 64

Reset button .................Quick Start Guide: 12

Resolution .................................................. 49, 50

RS485.................................................................. 54

Unique string of numbers that identifies

network devices. All devices communicate

with IP must have IP addresses. IP

address can be divided into network ID

and host ID.

Refer to Camera Control on page 54 for

details.

Security settings ............................................. 30

SMTP ................................................................... 75

(Simple Mail Transfer Protocol)

JPEG .................................................................... 50

(Joint Photographic Experts Group)

Protocol for sending e-mail on the Internet

and Intranet.

Standard gauge for compression of

colored still image by ITU-TS (International

Telecommunication Union: ex-CCITT)

and ISO (International Organization for

Standardization). It can compress a still

image between 1/10 to 1/100 of size.

Speciﬁcations ................................................... 75

Subnet mask ..................................................... 35

Method for spliting IP network into a series

of sub groups or subnets. By using this

system, it estimates whether IP address

of the addressed host is in local network

or remote network.

System Time ..................................................... 28

LAN ....................................................................... 35

(Local Area Network)

Computer networking in local area.

TCP/IP ................................................................. 75

Log ........................................................................ 66

Log-in ................................................................... 36

(Transmission Control Protocol/Internet

Protocol)

Protocol for communications between

computers are used as standard for

transmitting data over networks. This

is the standard protocol of the Internet

and at the same time, it is the most

popularized protocol. Network layer

protocol is IP, and transport layer protocols

are TCP（Transmission Control Protocol）

and UDP（User Datagram Protocol). FTP,

SMTP and other applications use TCP/IP.

Main Screen ...................................................... 22

Microphone input ............................................. 12

Motion Detection ............................................. 52

Network settings ............................................. 35

NTP server ......................................................... 29

(Network Time Protocol)

Server which provides accurate date and

time from network.

Upgrade ﬁrmware ............................................ 69

User ...................................................................... 30

OS ............................................................................ 3

White balance ................................................... 46

Protocol .............................................................. 75

PTZ (Pan/Tilt/Zoom operation) .................. 54

Refer to Camera Control on page 54 for

details.

㪐㪐㩷㪆㩷㪈㪍㪇

Download from Www.Somanuals.com. All Manuals Search And Download.

Speciﬁcations

Power supply

12 VDC 10 %, 24 VAC 10 %, PoE

Power consumption

Image pickup device

Effective pixels

12 VDC / 0.4 A, 24 VAC / 0.4 A

1/3.3 inch, CMOS

Horizontal 640, vertical 480 pixels

Progressive

Scanning system

Minimum object illuminance

White balance

0 lux with IR illuminators

AWB

Viewing angle

Wide end: horizontal 85.2° vertical 51.6°

Tele end: horizontal 23° vertical 14.8°

Input 1, output 1

I/O terminal

Image size

640 × 480, 352 × 240, 176 × 144

JPEG, MPEG4

Image compression system

Image quality setting

5 levels

Maximum frame rate at M-JPEG^*130 fps at 640 × 480

Maximum frame rate at MPEG 4^*130 fps at 640 × 480

Audio in/out terminal^*2

Network interface

Protocols

Mic in/Line out

10Base-T / 100Base-TX, RJ45 connector, IEEE 802.3af (PoE compatible)

TCP/IP, HTTP, UPnP, RTSP/RTP/RTCP, IGMP, SMTP, FTP, DHCP, NTP, DNS, DDNS,

PPPoE

Windows^®XP, Windows Vista^®Business

Internet Explorer^®Ver. 6.0 or 7.0

14°F to 122°F (-10°C to 50°C)

20 % to 80 %

Browser

Operating temperature

Operating humidity

Storage temperature

Storage humidity

Weight

14°F to 140°F (-10°C to 60°C)

90 % or less

969 g (2.14 lbs)

Dimensions

without Shade :

7.09 (L) × 2.76 (W) × 2.76 (H) inches (180 (L) × 70 (W) × 70 (H) mm) (excluding

protrusion)

Accessories

User's manual and install software (CD-ROM) (×1),

Quick start guide and important safeguards (×1),

AC adapter (×1), Warranty (×1), Screw kit (x1), RJ45 coupler (x1), Wrench (x1),

I/O connector (×2), Shade (x1), Mounting bracket and screw kit (x1), Silica gel (x1)

*1: Varies in accordance with the object, image quality, network environment and performance of the personal

computer used.

*2: The sound may not be clear depending on the conditions of the lines.

● Designs and speciﬁcations may change without prior notice for better improvement.

● Screens, photos, illustrations and other diagrams contained in this user's manual may slightly change

from actual ones.

㪈㪇㪇㩷㪆㩷㪈㪍㪇

Download from Www.Somanuals.com. All Manuals Search And Download.

Appearance Diagram

7.83 (199)

7.09 (180)

4.06 (103)

2.76 (70)

3.4 (86)

1.18 (30)

1/4"-20 UNC

Dimensions: inch (mm)

㪈㪇㪈㩷㪆㩷㪈㪍㪇

Download from Www.Somanuals.com. All Manuals Search And Download.

3.19 (81)

1.97 (50)

1.38 (35)

2.4 (61)

9.49 (241)

0.9 (23)

Dimensions: inch (mm)

㪈㪇㪉㩷㪆㩷㪈㪍㪇

Download from Www.Somanuals.com. All Manuals Search And Download.

Technology License Notice

MPEG-4 AAC Technology

THIS PRODUCT IS LICENSED UNDER THE MPEG-4 AAC AUDIO PATENT LICENSE. THIS

PRODUCT MAY NOT BE DECOMPILED, REVERSE-ENGINEERED OR COPIED, EXCEPT

REGARD TO PC SOFTWARE, YOU MAY MAKE SINGLE COPIES FOR ARCHIVAL PURPOSES.

FOR MORE INFORMATION, PLEASE REFER TO HTTP://WWW.VIALICENSING.COM.

MPEG-4 Visual Technology

THIS PRODUCT IS LICENSED UNDER THE MPEG-4 VISUAL PATENT PORTFOLIO LICENSE

FOR THE PERSONAL AND NON-COMMERCIAL USE OF A CONSUMER FOR (i) ENCODING

VIDEO IN COMPLIANCE WITH THE MPEG-4 VISUAL STANDARD ("MPEG-4 VIDEO") AND/

OR (ii) DECODING MPEG-4 VIDEO THAT WAS ENCODED BY A CONSUMER ENGAGED IN A

PERSONAL AND NON-COMMERCIAL ACTIVITY AND/OR WAS OBTAINED FROM A VIDEO

PROVIDER LICENSED BY MPEG LA TO PROVIDE MPEG-4 VIDEO. NO LICENSE IS GRANTED

OR SHALL BE IMPLIED FOR ANY OTHER USE. ADDITIONAL INFORMATION INCLUDING

THAT RELATING TO PROMOTIONAL, INTERNAL AND COMMERCIAL USES AND LICENSING

MAY BE OBTAINED FROM MPEG LA, LLC. SEE HTTP://WWW.MPEGLA.COM.

AMR-NB Standard

THIS PRODUCT IS LICENSED UNDER THE AMR-NB STANDARD PATENT LICENSE

AGREEMENT. WITH RESPECT TO THE USE OF THIS PRODUCT, THE FOLLOWING

LICENSORS' PATENTS MAY APPLY:

TELEFONAKIEBOLAGET ERICSSON AB: US PAT. 6192335; 6275798; 6029125; 6424938;

6058359. NOKIA CORPORATION: US PAT. 5946651; 6199035. VOICEAGE CORPORATION: AT

PAT. 0516621; BE PAT. 0516621; CA PAT. 2010830; CH PAT. 0516621; DE PAT. 0516621; DK

PAT. 0516621; ES PAT. 0516621; FR PAT. 0516621; GB PAT. 0516621; GR PAT. 0516621; IT

PAT. 0516621; LI PAT. 0516621; LU PAT. 0516621; NL PAT. 0516621; SE PAT 0516621; US

PAT 5444816; AT PAT. 819303/AT E 198805T1; AU PAT. 697256; BE PAT. 819303; BR PAT.

9604838-7; CA PAT. 2216315; CH PAT. 819303; CN PAT. ZL96193827.7; DE PAT. 819303/

DE69611607T2; DK PAT. 819303; ES PAT. 819303; EP PAT. 819303; FR PAT. 819303; GB

PAT. 819303; IT PAT. 819303; JP PAT. APP. 8-529817; NL PAT. 819303; SE PAT. 819303; US

PAT. 5664053. THE LIST MAY BE UPDATED FROM TIME TO TIME BY LICENSORS AND A CURRENT

VERSION OF WHICH IS AVAILABLE ON LICENSOR'S WEBSITE AT

HTTP://WWW.VOICEAGE.COM.

About the software

This product contains a piece of software licensed to TOSHIBA CORPORATION

(hereafter TOSHIBA) by a third party. The copyright and other intellectual property

rights of the software are held by this third party or the licensor. The software

is protected by the Copyright Law, Universal Copyright Convention, and other

intellectual property laws and agreements. The permission of Toshiba and the third

party must therefore be obtained before the software can be reproduced. Contact

Toshiba if you need it for more information at

http://www.toshibasecurity.com/support/ﬁrmware.jsp.

㪈㪇㪊㩷㪆㩷㪈㪍㪇

Download from Www.Somanuals.com. All Manuals Search And Download.

The original text (English) of end-user license agreement on free

software components used in the TOSHIBA Network Camera

GNU GENERAL PUBLIC LICENSE

Version 2, June 1991

51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA

Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it

is not allowed.

Preamble

The licenses for most software are designed to take away your freedom to share and change it. By

contrast, the GNU General Public License is intended to guarantee your freedom to share and change

free software--to make sure the software is free for all its users. This General Public License applies to

most of the Free Software Foundation's software and to any other program whose authors commit to

using it. (Some other Free Software Foundation software is covered by the GNU Lesser General Public

License instead.) You can apply it to your programs, too.

When we speak of free software, we are referring to freedom, not price. Our General Public Licenses

are designed to make sure that you have the freedom to distribute copies of free software (and charge

for this service if you wish), that you receive source code or can get it if you want it, that you can

change the software or use pieces of it in new free programs; and that you know you can do these

things.

To protect your rights, we need to make restrictions that forbid anyone to deny you these rights or

to ask you to surrender the rights. These restrictions translate to certain responsibilities for you if you

distribute copies of the software, or if you modify it.

For example, if you distribute copies of such a program, whether gratis or for a fee, you must give

the recipients all the rights that you have. You must make sure that they, too, receive or can get the

source code. And you must show them these terms so they know their rights.

We protect your rights with two steps: (1) copyright the software, and (2) oﬀer you this license which

gives you legal permission to copy, distribute and/or modify the software.

Also, for each author's protection and ours, we want to make certain that everyone understands that

there is no warranty for this free software. If the software is modiﬁed by someone else and passed on,

we want its recipients to know that what they have is not the original, so that any problems introduced

by others will not reﬂect on the original authors' reputations.

Finally, any free program is threatened constantly by software patents. We wish to avoid the

danger that redistributors of a free program will individually obtain patent licenses, in eﬀect making

the program proprietary. To prevent this, we have made it clear that any patent must be licensed for

everyone's free use or not licensed at all.

The precise terms and conditions for copying, distribution and modiﬁcation follow.

GNU GENERAL PUBLIC LICENSE

TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION

0. This License applies to any program or other work which contains a notice placed by the copyright

holder saying it may be distributed under the terms of this General Public License. The "Program",

below, refers to any such program or work, and a "work based on the Program" means either the

Program or any derivative work under copyright law: that is to say, a work containing the Program or a

portion of it, either verbatim or with modiﬁcations and/or translated into another language. (Hereinafter,

translation is included without limitation in the term "modification".) Each licensee is addressed as

"you".

Activities other than copying, distribution and modiﬁcation are not covered by this License; they are

outside its scope. The act of running the Program is not restricted, and the output from the Program is

covered only if its contents constitute a work based on the Program (independent of having been made

by running the Program). Whether that is true depends on what the Program does.

1. You may copy and distribute verbatim copies of the Program's source code as you receive it, in

any medium, provided that you conspicuously and appropriately publish on each copy an appropriate

the absence of any warranty; and give any other recipients of the Program a copy of this License along

with the Program.

㪈㪇㪋㩷㪆㩷㪈㪍㪇

Download from Www.Somanuals.com. All Manuals Search And Download.

The original text (English) of end-user license agreement on free

software components used in the TOSHIBA Network Camera (Cont.)

You may charge a fee for the physical act of transferring a copy, and you may at your option oﬀer

warranty protection in exchange for a fee.

2. You may modify your copy or copies of the Program or any portion of it, thus forming a work based

on the Program, and copy and distribute such modifications or work under the terms of Section 1

above, provided that you also meet all of these conditions:

a) You must cause the modiﬁed ﬁles to carry prominent notices stating that you changed the ﬁles

and the date of any change.

b) You must cause any work that you distribute or publish, that in whole or in part contains or is

derived from the Program or any part thereof, to be licensed as a whole at no charge to all third

parties under the terms of this License.

c) If the modified program normally reads commands interactively when run, you must cause it,

when started running for such interactive use in the most ordinary way, to print or display an

announcement including an appropriate copyright notice and a notice that there is no warranty (or

else, saying that you provide a warranty) and that users may redistribute the program under these

conditions, and telling the user how to view a copy of this License. (Exception: if the Program itself

is interactive but does not normally print such an announcement, your work based on the Program

is not required to print an announcement.)

These requirements apply to the modiﬁed work as a whole. If identiﬁable sections of that work are

not derived from the Program, and can be reasonably considered independent and separate works in

themselves, then this License, and its terms, do not apply to those sections when you distribute them

as separate works. But when you distribute the same sections as part of a whole which is a work based

on the Program, the distribution of the whole must be on the terms of this License, whose permissions

for other licensees extend to the entire whole, and thus to each and every part regardless of who wrote

it.

Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by

you; rather, the intent is to exercise the right to control the distribution of derivative or collective works

based on the Program.

In addition, mere aggregation of another work not based on the Program with the Program (or with a

work based on the Program) on a volume of a storage or distribution medium does not bring the other

work under the scope of this License.

3. You may copy and distribute the Program (or a work based on it, under Section 2) in object code

or executable form under the terms of Sections 1 and 2 above provided that you also do one of the

following:

a) Accompany it with the complete corresponding machine-readable source code, which must be

distributed under the terms of Sections 1 and 2 above on a medium customarily used for software

interchange; or,

b) Accompany it with a written oﬀer, valid for at least three years, to give any third party, for a charge

no more than your cost of physically performing source distribution, a complete machine-readable

copy of the corresponding source code, to be distributed under the terms of Sections 1 and 2

above on a medium customarily used for software interchange; or,

c) Accompany it with the information you received as to the oﬀer to distribute corresponding source

code. (This alternative is allowed only for noncommercial distribution and only if you received the

program in object code or executable form with such an oﬀer, in accord with Subsection b above.)

The source code for a work means the preferred form of the work for making modiﬁcations to it. For an

executable work, complete source code means all the source code for all modules it contains, plus any

associated interface deﬁnition ﬁles, plus the scripts used to control compilation and installation of the

executable. However, as a special exception, the source code distributed need not include anything

that is normally distributed (in either source or binary form) with the major components (compiler,

kernel, and so on) of the operating system on which the executable runs, unless that component itself

accompanies the executable.

If distribution of executable or object code is made by oﬀering access to copy from a designated place,

then oﬀering equivalent access to copy the source code from the same place counts as distribution of

the source code, even though third parties are not compelled to copy the source along with the object

code.

4. You may not copy, modify, sublicense, or distribute the Program except as expressly provided

under this License. Any attempt otherwise to copy, modify, sublicense or distribute the Program is void,

㪈㪇㪌㩷㪆㩷㪈㪍㪇

Download from Www.Somanuals.com. All Manuals Search And Download.

and will automatically terminate your rights under this License. However, parties who have received

copies, or rights, from you under this License will not have their licenses terminated so long as such

parties remain in full compliance.

5. You are not required to accept this License, since you have not signed it. However, nothing else

grants you permission to modify or distribute the Program or its derivative works. These actions are

prohibited by law if you do not accept this License. Therefore, by modifying or distributing the Program

(or any work based on the Program), you indicate your acceptance of this License to do so, and all its

terms and conditions for copying, distributing or modifying the Program or works based on it.

6. Each time you redistribute the Program (or any work based on the Program), the recipient

automatically receives a license from the original licensor to copy, distribute or modify the Program

subject to these terms and conditions. You may not impose any further restrictions on the recipients'

exercise of the rights granted herein. You are not responsible for enforcing compliance by third parties

to this License.

7. If, as a consequence of a court judgment or allegation of patent infringement or for any other

reason (not limited to patent issues), conditions are imposed on you (whether by court order,

agreement or otherwise) that contradict the conditions of this License, they do not excuse you from

the conditions of this License. If you cannot distribute so as to satisfy simultaneously your obligations

under this License and any other pertinent obligations, then as a consequence you may not distribute

the Program at all. For example, if a patent license would not permit royalty-free redistribution of the

Program by all those who receive copies directly or indirectly through you, then the only way you could

satisfy both it and this License would be to refrain entirely from distribution of the Program.

If any portion of this section is held invalid or unenforceable under any particular circumstance, the

balance of the section is intended to apply and the section as a whole is intended to apply in other

circumstances.

It is not the purpose of this section to induce you to infringe any patents or other property right claims

or to contest validity of any such claims; this section has the sole purpose of protecting the integrity

of the free software distribution system, which is implemented by public license practices. Many people

have made generous contributions to the wide range of software distributed through that system in

reliance on consistent application of that system; it is up to the author/donor to decide if he or she is

willing to distribute software through any other system and a licensee cannot impose that choice.

This section is intended to make thoroughly clear what is believed to be a consequence of the rest of

this License.

8. If the distribution and/or use of the Program is restricted in certain countries either by patents

or by copyrighted interfaces, the original copyright holder who places the Program under this License

may add an explicit geographical distribution limitation excluding those countries, so that distribution

is permitted only in or among countries not thus excluded. In such case, this License incorporates the

limitation as if written in the body of this License.

9. The Free Software Foundation may publish revised and/or new versions of the General Public

License from time to time. Such new versions will be similar in spirit to the present version, but may

diﬀer in detail to address new problems or concerns.

Each version is given a distinguishing version number. If the Program speciﬁes a version number of

this License which applies to it and "any later version", you have the option of following the terms and

conditions either of that version or of any later version published by the Free Software Foundation.

If the Program does not specify a version number of this License, you may choose any version ever

published by the Free Software Foundation.

10. If you wish to incorporate parts of the Program into other free programs whose distribution

conditions are diﬀerent, write to the author to ask for permission. For software which is copyrighted by

the Free Software Foundation, write to the Free Software Foundation; we sometimes make exceptions

for this. Our decision will be guided by the two goals of preserving the free status of all derivatives of

our free software and of promoting the sharing and reuse of software generally.

NO WARRANTY

11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR

THE PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE

STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE PROGRAM

"AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT

LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR

㪈㪇㪍㩷㪆㩷㪈㪍㪇

Download from Www.Somanuals.com. All Manuals Search And Download.

The original text (English) of end-user license agreement on free

software components used in the TOSHIBA Network Camera (Cont.)

PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH

YOU. SHOULD THE PROGRAM PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY

SERVICING, REPAIR OR CORRECTION.

12. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL

ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE

PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL,

SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO

USE THE PROGRAM (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED

INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM

TO OPERATE WITH ANY OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN

ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

END OF TERMS AND CONDITIONS

How to Apply These Terms to Your New Programs

If you develop a new program, and you want it to be of the greatest possible use to the public, the

best way to achieve this is to make it free software which everyone can redistribute and change under

these terms.

To do so, attach the following notices to the program. It is safest to attach them to the start of

each source ﬁle to most eﬀectively convey the exclusion of warranty; and each ﬁle should have at least

the "copyright" line and a pointer to where the full notice is found.

This program is free software; you can redistribute it and/or modify it under the terms of the GNU

General Public License as published by the Free Software Foundation; either version 2 of the

License, or (at your option) any later version.

This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without

even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See

the GNU General Public License for more details.

You should have received a copy of the GNU General Public License along with this program; if not,

write to the Free Software Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301

USA

Also add information on how to contact you by electronic and paper mail.

If the program is interactive, make it output a short notice like this when it starts in an interactive

mode:

Gnomovision version 69, Copyright (C) year name of author

Gnomovision comes with ABSOLUTELY NO WARRANTY; for details type `show w'.

This is free software, and you are welcome to redistribute it under certain conditions; type `show c'

for details.

The hypothetical commands `show w' and `show c' should show the appropriate parts of the General

Public License. Of course, the commands you use may be called something other than `show w' and

`show c'; they could even be mouse-clicks or menu items--whatever suits your program.

You should also get your employer (if you work as a programmer) or your school, if any, to sign a

"copyright disclaimer" for the program, if necessary. Here is a sample; alter the names:

Yoyodyne, Inc., hereby disclaims all copyright interest in the program `Gnomovision' (which makes

passes at compilers) written by James Hacker.

<signature of Ty Coon>, 1 April 1989

Ty Coon, President of Vice

This General Public License does not permit incorporating your program into proprietary programs.

If your program is a subroutine library, you may consider it more useful to permit linking proprietary

applications with the library. If this is what you want to do, use the GNU Lesser General Public License

instead of this License.

㪈㪇㪎㩷㪆㩷㪈㪍㪇

Download from Www.Somanuals.com. All Manuals Search And Download.

TOSHIBA AMERICA INFORMATION SYSTEMS, INC.

Surveillance & IP Video Products

9740 Irvine Boulevard,

Irvine, CA 92618-1697

Phone Number: (877) 855-1349

㪈㪇㪏㩷㪆㩷㪈㪍㪇

Download from Www.Somanuals.com. All Manuals Search And Download.

Technicolor Thomson DVD Player D M51DVS User Manual
Toshiba Blu ray Player BDX2400KU User Manual
Triarch Indoor Furnishings 31086 32 User Manual
Triarch Indoor Furnishings 39666 User Manual
U Line Ice Maker CO2075DWR User Manual
Universal Remote Control Universal Remote UR4U MDVR2 User Manual
ViewEra Computer Monitor V195MV User Manual
ViewSonic Digital Photo Frame VS12242 User Manual
Viper Automobile Alarm 420 ESP User Manual
Wayne Dalton Garage Door Opener 5255 User Manual