Satellite 1400/1405 Series
General Specifications
1400-S151
1400-S152
PS140U-027XF7
1405-S151
PS140U-027XF3
1405-S152
PS140U-027XFX
PS140U-027XFJ
Processor:
Memory:
Intel Celeron 1.20GHz; Integrated co-processor; 256KB Level 2 cache integrated on die; 133MHz front side bus clock
speed
256MB SDRAM, expandable to 1024MB; Expansion memory: SODIMM expansion memory
128/256/512Mbit PC133 SDRAM, 3.3V
Data/Address Bus Width: 64-bit/32-bit; BIOS ROM: 4Mbit, CMOS Flash EPROM, Ali M1535 Chipset
Drive(s):
HDD: 30.0GB supports PIO Mode 4
FDD: 3.5" 1.44MB
DVD-ROM/CDRW
Graphics/Video:
Audio:
14.1" TFT active -matrix display; internal display supports up to 16M colors at 1024 x 768; Trident CyberALADDIN-T
graphics controller; 16MB external UMA video memory; 3D graphics accelerator, AGP bus support; 2D graphics
accelerator, BitBLT hardware, hardware cursor, Direct Draw support
AK4543 Codec Chip; Ali M1535 Sound Chip, 16-bit stereo; Built-in stereo speakers; Direct 3D sound; DirectSound
(supported by driver) and DirectMusic; Full duplex and MIDI (play back) support; Sound Volume Control Dial;
headphone and microphone ports
Communication: Integrated V.90/56K modem, Data and fax support; Integrated 10/100 Ethernet LAN
Expansion:
Ports:
2 expansion memory slots; 2PC card slots support 2 Type II or 1 Type III PC cards; 32-bit CardBus ready
RGB (monitor); ECP Parallel printer; 3 USB; RJ-45 LAN; RJ-11 modem; Infrared; TV-Out (NTSC/PAL output; RCA
jack)
Keyboard:
Battery:
85 keys with 12 function keys, TouchPad pointing device
9 cell, rechargeable, removable Li-Ion, approximately 3H battery life
7.4 lbs
Weight:
Dimensions:
Software:
(L)12.8" x (W)11.2" x (H)1.7"
MS Windows XP Pro pre-installed (1400-S151/1405-S152); MS Windows XP Home pre-installed (1405-S151/1400-
S152); MS Internet Explorer, Online documentation, Adobe Acrobat Reader, Intuit Quicken Basic 2001, Norton
Antivirus 2002, AOL (3-month offer), Toshiba custom utilities, Toshiba great software offer; Lotus SmartSuite
Millennium Edition (1405 Series only)
Security:
Warranty:
Slot for computer lock; Main battery pack (sliding lock); HDD and memory (by screw only), Built-in Modem/LAN
(screw only), User Power-On password, Setup Security, HDD password, Keyboard lock (by hotkey), Screen Blank (by
hotkey), Screen Saver (by software)
1 year parts, labor, and battery
Toshiba TRR
Page 1
7/02, Satellite
Download from Www.Somanuals.com. All Manuals Search And Download.
Satellite 1400 Series Exploded Lower View
Toshiba TRR
Page 3
7/02, Satellite
Download from Www.Somanuals.com. All Manuals Search And Download.
Satellite 1400 Series Part Numbers
Ref. #
Code Part #
Description
PIR Comments
C1Y2 PS140U-027XF3
C1Y2 PS140U-027XF3B
C1Y2 PS140U-027XF7
C1Y2 PS140U-027XF7B
C1Y2 PS140U-027XF7W
C1Y2 PS140U-027XF7WB 1400-S151 (027XF7WB)B-STK
C1Y2 PS140U-027XF7X 1400-S151/30 (027XF7X)
C1Y2 PS140U-027XF7XB 1400-S151 (027XF7X)B-STK
1400-S152/30 (027XF3)
1400-S152 (027XF3B) B-STK
1400-S151/30 (027XF7)
1400-S151 (027XF7B) B-STK
1400-S151/30 (027XF7W)
S1400-S152/30, WXP Home, 1.20GHz Cel, 256MB, CD-RW/DVD, 14 TFT, Modem/LAN, (W’less Ready)
S1400-S152/30, WXP Home, 1.20GHz Cel, 256MB, CD-RW/DVD, 14 TFT, Modem/LAN, (W’less Ready), Remf
S1400-S151/30, WXP Pro, 1.20GHz Cel, 256MB, CD-RW/DVD, 14 TFT, Modem/LAN, (W’less Ready)
S1400-S151/30, WXP Pro, 1.20GHz Cel, 256MB, CD-RW/DVD, 14 TFT, Modem/LAN, (W’less Ready), Remf
S1400-S151/30, WXP Pro, 1.20GHz Cel, 256MB, CD-RW/DVD, 14 TFT, Modem/LAN, (Office XP SB), (W’less Ready)
S1400-S151/30, WXP Pro,1.20GHz Cel,256MB,CD-RW/DVD,14 TFT,Modem/LAN,(Office XP SB),(W’less Ready),Remf
S1400-S151/30, WXP Pro, 1.20GHz Cel, 256MB, CD-RW/DVD, 14 TFT,Modem/LAN,(Office XP Pro),(W’less Ready)
S1400-S151/30,WXP Pro,1.20GHz Cel,256MB,CD-RW/DVD,14 TFT,Modem/LAN,(Office XP Pro),(W’less Ready),Remf
S1405-S152/30, WXP Pro, 1.20GHz Cel, 256MB, CD-RW/DVD, 14 TFT, Modem/LAN, (W’less Ready)
S1405-S152/30, WXP Pro, 1.20GHz Cel, 256MB, CD-RW/DVD, 14 TFT, Modem/LAN, (W’less Ready), Remf
S1405-S151/30, WXP Home, 1.20GHz Cel, 256MB, CD-RW/DVD, 14 TFT, Modem/LAN, (W’less Ready)
S1405-S151/30, WXP Home, 1.20GHz Cel, 256MB, CD-RW/DVD, 14 TFT, Modem/LAN, (W’less Ready), Remf
S1405-S151/30, WXP Home, 1.20GHz Cel, 256MB, CD-RW/DVD, 14 TFT, Modem/LAN, (W’less Ready), Sp
S1400-S151/30, WXP Pro, 1.20GHz Cel, 256MB, CD-RW/DVD, 14 TFT, Modem/LAN, (W’less Ready), Sp
S1400-S151W/30, WXP Pro, 1.20GHz Cel, 256MB, CD-RW/DVD, 14 TFT, Modem/LAN, Wi-Fi LAN
S1400-S151W/30, WXP Pro, 1.20GHz Cel, 256MB, CD-RW/DVD, 14 TFT, Modem/LAN, Wi-Fi LAN, Remf
S1400-S151W/30, WXP Pro, 1.20GHz Cel, 256MB, CD-RW/DVD, 14 TFT, Modem/LAN, Wi-Fi LAN, (NFS)
S1400-S151W/30, WXP Pro, 1.20GHz Cel, 256MB, CD-RW/DVD, 14 TFT, Modem/LAN, Wi-Fi LAN, (NFS)
Kingston 128MB PC133 SDRAM Memory Module
C1Y2 PS140U-027XFJ
C1Y2 PS140U-027XFJB
C1Y2 PS140U-027XFX
C1Y2 PS140U-027XFXB
1405-S152/30 (027XFJ)
1405-S152 (027XFJB) B-STK
1405-S151/30 (027XFX)
1405-S151 (027XFXB) B-STK
C1Y3 PS140U-027XFNNC 1405-S151/30 (027XFNNC)
C1Y3 PS140U-027XFPNC 1400-S151/30 (027XFPNC)
C1Y4 PS140U-027W57
C1Y4 PS140U-027W57B
1400-S151W/30 (027W57)
1400-S151W (027W57B)B-STK
C1Y5 PS140U-027W5701 1400-S151W/30 (027W5701)
C1Y6 PS140U-027W5702 1400-S151W/30 (027W5702)
OP01
C1Y5 KTT-SO133/128
MEM MODULE, 128MB
MEM MODULE, 256MB
UNIV AC ADAPTER
AC ADAPTER
OP01-A C1Y2 KTT-SO133/256
Kingston 256MB PC133 SDRAM Memory Module
OP02
C1Y3 PA3083U-1ACA
C1Y2 P000337890
C1Y2 P000327770
C1Y2 PA3107U-1BRS
C1Y2 P000324210
Input:100V-240V, 1.2A-0.6A, 50-60Hz, Output:15VDC, 5A, 75 watt,(U,C,Z)
Input: 100V-240V, 1.2A-0.6A, 50-60Hz, Output: 15VDC, 5A (UA2042P02)
(U, C, Z)
OP02A
OP02B
OP03
AC CORD SET
BATTERY PACK
Lithium-Ion 10.8VDC, 4500mAh, with Recycle Label, (U,E)
OP03A
BATTERY PACK
CEH Lithium-Ion 10.8VDC, 4500mAh, with Recycle Label, XM2033P02, (U,E)
CEH Lithium-Ion 10.8VDC, 4500mAh, with Recycle Label, XM2040P02 (U E,Z)
CEH Lithium-Ion 10.8VDC, 4500mAh, with Recycle Label (U,E,Z)
For Main Battery Pack
OP03A-1 C1Y4 P000337840
OP03A-2 C1Y5 P000350480
BATTERY PACK
BATTERY PACK
OP04
OP05
OP05A
S01
S02
S03
S04
S05
S06
S07
S08
S09
S10
S11
S12
S13
S14
1
C1Y2 PA2488U
BATT CHARGER (MAIN)
WIRELESS LAN CARD KIT
WIRELESS LAN CARD
T SCREW, M2.5X6
TG SCREW, M2.5X4BN
SCREW, M2X6
C1Y2 PA3212U-1MPC
C1Y6 P000339520
C1Y6 P000300290
C1Y3 P000318000
C1Y6 P000207940
C1Y2 P000317990
C1Y2 P000274010
C1Y2 P000290500
C1Y4 P000227770
C1Y2 P000322980
C1Y2 P000273730
C1Y2 P000239510
C1Y3 P000315550
C1Y2 P000273850
C1Y4 P000339380
C1Y4 P000261770
C1Y2 P000348950
C1Y2 P000323270
C1Y3 P000348960
C1Y2 P000347340
C1Y2 P000347350
C1Y2 P000347360
C1Y2 P000347370
C1Y2 P000348650
C1Y5 P000328480
C1Y2 P000322090
C1Y5 P000339520
C1Y4 P000332290
C1Y3 P000334580
C1Y2 P000309120
C1Y2 P000310980
C1Y4 P000310990
C1Y2 P000311000
C1Y2 P000311010
C1Y4 P000311020
C1Y2 P000311030
C1Y2 P000311040
C1Y3 P000311050
C1Y2 P000316700
C1Y2 P000318970
C1Y4 P000309110
C1Y4 P000311060
C1Y2 P000338370
Agere Systems MPCI3A-20/R, ZA2314P04
Black, Flat-Head (low profile) screw
TG SCREW, M2.5X6BN
T GRIP SCREW, M2X5C
GRIP SCREW, M2.5X16Z
SCREW, M2.5X2.6BN
GRIP SCREW, M2.5X25BN
T GRIP SCREW, M2X4Z
GRIP SCREW, M2.5X5Z
TG SCREW, M2.5X2.8B
T GRIP SCREW, M2X3C
THIN SCREW, M3X4Z
GRIP SCREW, M2X12Z
PCB ASSY FRTSA2
CARDBUS CONNCTOR
PCB ASSY FRTSD1
PCB ASSY FRTBA1
PCB ASSY FRTHD1
PCB ASSY FRTPW1
PCB ASSY FRTCW1
IC RH80530NZ009
256MB SO DIMM
Black Grip Screw
Black, Flat-Head (low profile) screw
Zinc (gold) flat-head (low profile head) screws
Silver, Flat-Head (low profile) screw
Silver, Flat-Head (low profile) screw
System Board, without CPU, without memory, A5A000255010
PC Card Connector, G36220279179
Sound Board, A5A000233030
1A
2
3
Battery (Battery Terrminal) Board, G70C00004210
HDD Connector Board (contains W-LAN switch), G70C00005210
Power Switch Board, G70C00006210
4
5
6
CD Switch Board, G70C00007210
7
Intel 1.20GHz Cel, apply grease to CPU before mounting Cooling Mod
Approved makes = Toshiba; SME - Samsung, ELP - Elpida; HYS - Hyundia
Modem Daughter Card, Askey Computer 1456VQL4 (INT), ZA2300P06
Agere Systems MPCI3A-20/R, ZA2314P04
8-A
9
MDC MODEM
10
WIRELESS LAN CARD
COLOR LCD MODULE
FL TUBE SET
11
Chimei N141X6-02, 14.1 XGA TFT, VF2093P01
11A
12
COLOR LCD MODULE
FL TUBE
Samsung LTN141X7-L06, 14.1XGA TFT, VF2048P01
12A
12B
12C
12D
12E
12F
12G
12H
13
AL TAPE
WIRE TAPE
SCREW, M2X1.7
SCREW, M2X2.5
PCB COVER
LAMP COVER
CLIP
COLOR LCD MODULE
FL LAMP KIT
LG Philips LP141X7-C1TO,14.1 XGA TFT, VF2062P01"
Toshiba LTM14C433, 14.1 XGA TFT, VF2047P01"
Toshiba LTM14C501, 14.1 XGA TFT, VF2096P01"
13A
14
14A
15
COLOR LCD MODULE
FL TUBE SET
COLOR LCD MODULE
Toshiba TRR
Page 4
7/02, Satellite
Download from Www.Somanuals.com. All Manuals Search And Download.
Satellite 1400 Series Part Numbers, (cont.)
Ref. #
Code Part #
Description
PIR Comments
15A
16
C1Y2 P000338550
C1Y2 P000348970
C1Y2 P000350800
C1Y2 P000261140
C1Y2 P000350810
C1Y2 P000316210
C1Y4 P000350820
C1Y5 P000347420
C1Y2 P000341840
C1Y4 P000341850
C1Y2 P000343820
C1Y2 P000349540
C1Y2 P000347430
C1Y2 P000347440
C1Y2 P000349920
C1Y2 P000347450
C1Y3 P000347760
C1Y2 P000349670
C1Y2 P000347460
C1Y2 P000220300
C1Y2 P000322640
C1Y2 P000331520
C1Y2 P000347480
C1Y4 P000347490
C1Y3 P000347500
C1Y4 P000347510
C1Y3 P000347520
C1Y2 P000347530
C1Y2 P000347540
C1Y2 P000347550
C1Y3 P000347560
C1Y2 P000348990
C1Y4 (RESERVED)
C1Y4 P000337840
C1Y2 P000350480
C1Y6 P000347580
C1Y3 UE2024P36KB-SP
C1Y6 P000327770
C1Y2 P000347590
C1Y2 P000348470
C1Y6 P000349710
C1Y2 P000347970
C1Y2 P000348530
C1Y2 P000349770
C1Y3 P000347980
C1Y4 P000347990
C1Y2 P000222130
C1Y4 P000348000
C1Y2 P000348540
C1Y2 P000349780
C1Y2 P000348010
C1Y2 P000348550
C1Y2 P000349790
C1Y2 P000348020
C1Y2 P000348560
C1Y2 P000349800
C1Y2 P000348030
C1Y2 P000348570
C1Y2 P000349810
C1Y2 P000348040
C1Y4 P000348580
C1Y4 P000349820
C1Y5 P000348050
C1Y5 P000348590
C1Y2 P000349830
C1Y2 P000347600
C1Y2 P000347610
C1Y2 P000348480
C1Y2 P000349720
C1Y4 P000347620
C1Y3 P000343570
FL TUBE SET
COLOR LCD MODULE
FL TUBE
Sharp LQ141X1LH83, 14.1 XGA TFT, VF2065P02"
16A
16B
16C
16D
16E
17
SCREW, M2X2
COVER S
AL TAPE
TAPE
FL INVERTER
HDD UNIT (30GB)
HDD UNIT (30GB)
HDD UNIT (30GB)
CD-RW/DVD-ROM
CD-RW/DVD-ROM
FDD UNIT
18-A
18-A-1
18-A-2
19-A
19-A-1
20
Toshiba, MK30KEF, HDD2169B
CEH IBM IC25N030ATCS04 (ATD04T), P/N: 07N8326, 07N9318, G8BC00004210
CEH Hitachi DK23DA-30F, G8BC00006210
Toshiba SD-R2102-OAHB, G8CC00009210
CEH Panasonic (KME - Kyushu Matsushita Electric) UJDA720, ZA2431P02
Teac FD05HG-7778, G8AC00002210, requires P000347760
CEH Samsung SFD-321S/TB1 G8AC00007110, requires P000347760
Mitsumi D353F3X/R-3220, G8AC00003110, requires P000349670
FDD Cable for Teac or Samsung FDD
20-1
20-A
21
FDD UNIT
FDD UNIT
1.0MM PITCH FFC
1.0MM PITCH FFC
RJ11 HARNESS
MODULAR CABLE
AC ADAPTER
RTC BATTERY
0.5MM PITCH FFC
0.5MM PITCH FFC
0.5MM PITCH FFC
0.5MM PITCH FFC
0.5MM PITCH FFC
BATTERY HARNESS
DC JACK HARNESS
DC FAN
21-A
22
CDA FDD Cable for Mitsumi FDD
23
Modem Cable
24
Input:100V-240V 1.5A-0.85A, 50-60HZ; Output: 15V 4A, PA3092U—1ACA
Lithium Ion, 3.6V, 15mAh
25
26
Cable between Sound Board and System Board
Cable between Sound Board and System Board
Cable between Sound Board and CD Switch Board
27
28
29
30
Cable between Touch Pad and System Board
Cable between Battery Board and System Board
DC-In Cable
Cooling Fan Module, apply grease to CPU before installing Cooling Mod.
Heatsink unit, apply grease to chip before installing
31
32
33
34
FIN
TOUCH PAD
35
36
37
BATTERY PACK
BATTERY PACK
Lithium-Ion 10.8VDC, 4500mAh, with Recycle Label, XM2040P02 (U E,Z)
CEH Lithium-Ion 10.8VDC, 4500mAh, with Recycle Label (U,E,Z)
Minebea WLJ-5508W, G83C0000E210, (U)
37-1
38
KEYBOARD UNIT
KEYBOARD UNIT, SP
AC CORD SET
38-A
39
For Latin America, Alps Electric KFRMBA059A, UE2024P36
(U, C, Z)
40
BASE ASSY
For units with letter C stamped on Base in battery compartment area
For units with letter D stamped on Base in battery compartment area
For units with letter P stamped on Base in battery compartment area
For units with letter C stamped on Base in battery compartment area
For units with letter D stamped on Base in battery compartment area
For units with letter P stamped on Base in battery compartment area
40-A
40-B
40A
40A-A
40A-B
40B
40C
40D
40E
40E-A
40E-B
40F
40F-A
40F-B
40G
40G-A
40G-B
40H
40H-A
40H-B
40I
BASE ASSY
BASE ASSY
FIR COVER
FIR COVER
FIR COVER
BOTTOM CUSHION
HDD BRACKET
GUM CUSHION
MEMORY COVER ASSY
MEMORY COVER ASSY
MEMORY COVER ASSY
MINI PCI COVER
MINI PCI COVER
MINI PCI COVER
MDC COVER
For units with letter C stamped on Base in battery compartment area
For units with letter D stamped on Base in battery compartment area
For units with letter P stamped on Base in battery compartment area
For units with letter C stamped on Base in battery compartment area
For units with letter D stamped on Base in battery compartment area
For units with letter P stamped on Base in battery compartment area
Modem Slot Cover, For units with letter C stamped on Base
Modem Slot Cover, For units with letter D stamped on Base
Modem Slot Cover, For units with letter P stamped on Base
For units with letter C stamped on Base in battery compartment area
For units with letter D stamped on Base in battery compartment area
For units with letter P stamped on Base in battery compartment area
For units with letter C stamped on Base in battery compartment area
For units with letter D stamped on Base in battery compartment area
For units with letter P stamped on Base in battery compartment area
For units with letter C stamped on Base in battery compartment area
For units with letter D stamped on Base in battery compartment area
For units with letter P stamped on Base in battery compartment area
Plastic Brace
MDC COVER
MDC COVER
BATT COVER ASSY
BATT COVER ASSY
BATT COVER ASSY
REAR CONN. COVER
REAR CONN. COVER
REAR CONN. COVER
HDD COVER ASSY
HDD COVER ASSY
HDD COVER ASSY
CONN. HOLDER ASSY
FRONT COVER ASSY
FRONT COVER ASSY
FRONT COVER ASSY
BATT CONN. COVER
SPRING, BATT SAFETY
40I-A
40I-B
40J
40J-A
40J-B
41
42
For units with letter C stamped on Base in battery compartment area
For units with letter D stamped on Base in battery compartment area
For units with letter P stamped on Base in battery compartment area
42-A
42-B
43
43A
Toshiba TRR
Page 5
7/02, Satellite
Download from Www.Somanuals.com. All Manuals Search And Download.
Satellite 1400 Series Part Numbers, (cont.)
Ref. #
Code Part #
Description
PIR Comments
44
C1Y2 P000347630
C1Y2 P000347640
C1Y4 P000348490
C1Y2 P000349730
C1Y2 P000283510
C1Y2 P000309450
C1Y3 (RESERVED)
C1Y3 P000349010
C1Y2 P000349090
C1Y2 P000350000
C1Y2 P000349030
C1Y2 P000349110
C1Y2 P000350010
C1Y2 P000347790
C1Y5 P000349040
CPU HOLDER
45
W'LESS LAN SW. KNOB
W'LESS LAN SW. KNOB
W'LESS LAN SW. KNOB
CPU STUD
For units with letter C stamped on Base in battery compartment area
45-A
45-B
46
47
48-49
50
50-A
50-B
50A
50A-A
50A-B
50AA
50AB
For units with letter D stamped on Base in battery compartment area
For units with letter P stamped on Base in battery compartment area
M2.5X6 Stud Screw
HEXA STUD
M2.5X14 Stud Screw
COVER ASSY
For units with letter C stamped on Base in battery compartment area
For units with letter D stamped on Base in battery compartment area
For units with letter P stamped on Base in battery compartment area
For units with letter C stamped on Base in battery compartment area
For units with letter D stamped on Base in battery compartment area
For units with letter P stamped on Base in battery compartment area
COVER ASSY
COVER ASSY
COVER SUB ASSY
COVER SUB ASSY
COVER SUB ASSY
LCD CUSHION
TOUCH PAD BUTTON
TOUCH PAD BUTTON
TOUCH PAD BUTTON
LCD COVER ASSY
LCD COVER ASSY
LCD COVER ASSY
LCD LATCH HOOK
LCD LATCH HOOK
LCD LATCH HOOK
SENSOR SW. MAGNET
D STICK TAPE
For units with letter C stamped on Base in battery compartment area
For units with letter D stamped on Base in battery compartment area
For units with letter P stamped on Base in battery compartment area
For units with letter C stamped on Base in battery compartment area
For units with letter D stamped on Base in battery compartment area
For units with letter P stamped on Base in battery compartment area
For units with letter C stamped on Base in battery compartment area
For units with letter D stamped on Base in battery compartment area
For units with letter P stamped on Base in battery compartment area
50AB-A C1Y6 P000349120
50AB-B C1Y5 P000350020
50B
C1Y2 P000349050
C1Y2 P000349130
C1Y2 P000349860
C1Y2 P000347820
50B-A
50B-B
50BA
50BA-A C1Y2 P000348630
50BA-B C1Y2 P000349870
50BB
50BC
50C
50D
50E
50F
50G
50H
50I
50J
50J-A
50J-B
50K
50L
50M
50N
51
C1Y2 P000347830
C1Y2 P000347840
C1Y2 P000349060
C1Y4 P000349070
C1Y6 P000347870
C1Y2 P000347880
C1Y2 P000347890
C1Y2 P000347900
C1Y2 P000350190
C1Y2 P000347920
C1Y6 P000348640
C1Y2 P000349880
C1Y2 P000347930
C1Y4 P000347940
C1Y6 P000347950
C1Y4 P000347960
C1Y2 P000349020
C1Y2 P000349100
C1Y4 P000349750
C1Y3 P000312850
C1Y3 P000322780
C1Y2 P000322790
C1Y2 P000347670
C1Y2 P000333940
C1Y2 P000349960
C1Y5 P000349970
C1Y2 P000347690
C1Y3 P000348520
C1Y2 P000349760
C1Y4 P000347700
C1Y2 (RESERVED)
C1Y5 P000347710
C1Y2 P000347720
C1Y2 (RESERVED)
C1Y4 P000347730
C1Y2 P000316400
C1Y5 P000347740
C1Y6 P000347750
C1Y3 (RESERVED)
C1Y2 P000347770
C1Y2 (RESERVED)
C1Y3 P000316910
C1Y3 P000319730
C1Y4 P000320520
C1Y2 (RESERVED)
C1Y5 597890
BRAKE HINGE, RIGHT
BRAKE HINGE, LEFT
BH UPPER INSULATOR
SPEAKER, LEFT
Brake Hinge Upper Insulator
SPEAKER, RIGHT
ANTENNA CABLE
LCD HARNESS
Wireless LAN Antenna
LCD/FL Cable
For units with letter C stamped on Base in battery compartment area
For units with letter D stamped on Base in battery compartment area
For units with letter P stamped on Base in battery compartment area
CABLE HOLDER
CABLE HOLDER
CABLE HOLDER
CABLE EARTH PLATE
HARNESS HOLDER
CUSHION TAPE
TOSHIBA BADGE
LCD MASK ASSY
LCD MASK ASSY
LCD MASK ASSY
LCD CUSHION
TOSHIBA BADGE
LCD GUM CUSHION
SCREW SEAL
LCD MASK SEAL
LCD SUPPORT 14, L.
LCD SUPPORT 14, R.
KEYBD HOLDER ASSY
KEYBD HOLDER ASSY
KEYBD HOLDER ASSY
PRODUCT BADGE
for Display Cover
For units with letter C stamped on Base in battery compartment area
For units with letter D stamped on Base in battery compartment area
For units with letter P stamped on Base in battery compartment area
51-A
51-B
51A
51B
51C
52
For Display Mask
53
54
55
56
Keyboard Brace, For units with letter C stamped on Base
Keyboard Brace, For units with letter D stamped on Base
Keyboard Brace, For units with letter P stamped on Base
56-A
56-B
57
58-59
60
SUPPORT PLATE
KEYBD HOLDER PLATE
Metal Plate
61
62-63
64
HDD HOLDER ASSY
HDD INSULATOR
ODD REAR BRACKET
ODD SIDE BRACKET
HDD Bracket
65
66
Optical Disk Drive Rear Bracket
Optical Disk Drive Side Bracket
67
68
69
FDD BRACKET ASSY
70
71
CHINA LABEL
LITHUANIA LABEL
CARD LABEL
72
73
74-79
210
215
EXT. MICROPHONE
BAG ACCESSORY
Custom hardware - not used in all models
Carrying Case
C1Y6 TOSH4
Toshiba TRR
Page 6
7/02, Satellite
Download from Www.Somanuals.com. All Manuals Search And Download.
Satellite 1400 Series Disassembly Overview
The information offered in this section is an overview of the Maintenance Manual, Chapter 4, Replacement
Procedures. If you have any questions or concerns regarding the proper procedure please refer to the Mainte-
nance Manual through the Toshiba Service and Support Website before you proceed.
This section explains how to remove Field
Replaceable Units (FRUs). It may not be neces-
sary to remove all the FRUs in order to replace
one.
The chart is a guide to which FRUs need to be
removed in order to remove others. The section
numbers on the chart refer to the sections in the
Maintenance Manual, Chapter 4.
Always start by removing the battery pack, next,
optional items such as the optional PC card and
optional memory module, then follow the line on
the chart to determine which FRU you must
remove next in order to repair the one you think is
causing the computer to operate improperly.
To remove the battery, follow the steps below.
CAUTION: When handling battery packs, be
careful not to short circuit the terminals. Also
do not drop, hit or otherwise apply impact; do
not scratch or break the casing.
1. Turn the computer upside down.
2. Slide the battery latch to the left to
release it, then pull the battery cover
slightly forward and lift it out.
3. Lay the battery cover upside down. Push
the latches to the outside and lift out the
battery pack.
NOTE: For environmental reasons, do not
throw away a spent battery pack. Please follow
local ordinances or regulations for its disposal.
To remove an optional PC card, follow the steps
below.
1. Turn the computer right side up.
2. Press the eject button for the PC card
you want to remove, it will extend slightly.
3. Press the button again.
4. Grasp the PC card and remove it.
Toshiba TRR
Page 7
7/02, Satellite
Download from Www.Somanuals.com. All Manuals Search And Download.
Satellite 1400 Series Disassembly Overview, cont.
To remove an optional SD card, follow the steps
below.
1. Turn the computer right side up.
2. Push the SD card in and release it to pop
the card out slightly.
3. Grasp the SD card and remove it.
To remove the HDD, follow the steps below.
1. Turn the computer upside down.
2. Remove one M2.5x4 black flat-head
screw securing the HDD cover.
3. Lift off the HDD cover.
4. Pull the guide to remove the HDD. Be
careful not to damage the connector.
5. Place the HDD pack on a flat surface and
remove four M2x4 silver flat-head
screws.
6. Remove the HDD bracket.
CAUTION: Do not apply pressure to the top or
bottom of the HDD.
To remove a memory module, follow the steps
below.
1. Turn the computer upside down.
2. Remove one M2.5x4 black flat-head
screw.
3. Lift off the memory slot cover.
4. Gently press out on two latches. One
end of the memory module will pop up.
5. Grasp the memory module and remove
it.
CAUTION: Do not try to remove a memory
module with the computer turned on. You can
damage the computer and the memory.
Do not touch the connectors on the memory
module(s) or on the computer. Debris on the
connectors may cause memory access problems.
Toshiba TRR
Page 8
7/02, Satellite
Download from Www.Somanuals.com. All Manuals Search And Download.
Satellite 1400 Series Disassembly Overview, cont.
To remove the modem daughter card (MDC), follow
the steps below.
1. Turn the computer upside down.
2. Remove one M2.5x4 black flat-head
screw.
3. Lift off the modem slot cover.
4. Remove two M2x4 super flat screws
securing the MDC.
5. Carefully lift up the MDC to disconnect it
from PJ9 (S1400) or PJ125 (S2400) on
the system board.
6. Carefully disconnect the modem cable
from JP1 on the MDC.
To remove the wireless LAN card, follow the steps
below.
1. Remove one M2.5x4 black flat-head
screw.
2. Lift off the Wireless LAN card slot cover.
3. Disconnect the Wireless LAN antenna
cables (black and white) from the
Wireless LAN card using an antenna
coaxial cable disconnector.
4. Push the Wireless LAN card lock
latches outward to release the card. It
will pop up to about a 45 degree angle.
5. Pull out the Wireless LAN card. Be
careful not to damage the connector.
To install the wireless LAN card (an option in some
models), follow the steps below.
CAUTION: Be sure to turn the computer off before
removing the card. Otherwise, the computer or the
card may be damaged.
1. Insert the Wireless LAN card into the
connector at an angle of 45 degrees.
2. Gently push the Wireless LAN card down
until latches on both sides engage to
hold it in place.
3. Connect the Wireless LAN antenna
(black and white) cables to the
connectors on the card.
CAUTION: Be sure the cables lie inside the guide.
Be careful not to damage or pinch the cables
when you seat the card.
4. Seat the Wireless LAN card slot cover.
5. Secure the cover with one M2.5x4 black
flat-head screw.
CAUTION: There are two MAC address barcode
labels in the package with the card. Apply one
labelo next to the Wireless LAN socket and one
on the box the computer was shipped in. Remove
old labels before applying the new ones. The
computer may have MAC address barcod labels
both wired and Wireless LANs. Be sure to replace
the correct label.
Toshiba TRR
Page 9
7/02, Satellite
Download from Www.Somanuals.com. All Manuals Search And Download.
Satellite 1400 Series Disassembly Overview, cont.
To remove the keyboard, follow the steps below.
1. Open the display panel.
2. Insert the fingernails of both hands into
notches in the keyboard brace and the
computer, and pry up to release the
brace at twelve points. Remove the
brace.
3. Remove one M2.5x4 black flat-head
screw securing the metal brace.
4. Remove two M2.5x2.6 black flat-head
screws.
5. Rotate the keyboard out and lay it on top
of the palmrest.
6. Disconnect the keyboard cable from
PJ2003 on the system board and remove
the keyboard.
"
#
To remove the power switch board, follow the steps
below.
1. Disconnect the SUMI card from PJ2018.
2. Remove one M2.5x4 black flat-head
screw.
3. Remove the power switch board and
turn it over.
4. Disconnect the SUMI card from PJ7200.
!
To remove the top cover with display assembly,
follow the steps below.
1. Turn the computer upside down and
remove the following nineteen screws:
• Thirteen M2.5x6 black flat-head
• Six M2.5x5 black flat-head
2. Turn the computer right side up and open
the display panel.
3. Remove two M2.5x6 black screws and
two M2.5x16 black screws.
4. Remove the metal plate.
5. Disconnect the LCD/DL cable from
PJ5001 and the speaker cables from
PJ2020 and PJ2021 on the system
board.
6. Remove one M2x6 screw securing the
top cover.
7. Remove the top cover with display
assembly starting from the front. Be
careful not to damage the wireless LAN
antenna coaxial cables.
!
Images continued on the next page
Toshiba TRR
Page 10
7/02, Satellite
Download from Www.Somanuals.com. All Manuals Search And Download.
Satellite 1400 Series Disassembly Overview, cont.
"
"
#
To remove the optical disk drive, follow the steps
below.
1. Disconnect the optical disk drive (DVD)
from PJ2001 on the system board.
2. Carefully slide the drive to the right to
remove it.
3. Remove two M2x5 silver thin flat-head
screws and the short metal brace.
4. Remove one M2x3 silver thin flat-head
screw and the long metal brace.
!
To remove the FDD, follow the steps below.
1. Disconnect the FDD SUMI card from
PJ2007 on the system board.
2. Lift out the FDD.
3. Remove four M2.5x2.6 screws securing
the metal case to the FDD and remove
the metal case.
4. Disconnect the FDD DUMI card from the
connector of the FDD.
NOTE: Two types of SUMI cards are used; one
manufactured by TEAC and SAMSUNG, and the
other by MITSUMI.
!
Toshiba TRR
Page 11
7/02, Satellite
Download from Www.Somanuals.com. All Manuals Search And Download.
Satellite 1400 Series Disassembly Overview, cont.
To remove the touch pad, follow the steps below.
1. Disconnect the touch pad SUMI card
from PJ2004 on the system board.
2. Remove one M2x5 silver thin flat-head
screw securing the touch pad.
3. LIft out the touch pad.
4. Disconnect the touch pad SUMI card
from CN1 on the touch pad.
!
To remove the battery board, follow the steps below.
1. Disconnect the battery cable from
PJ8810.
2. Lift out the battery board.
3. Disconnect the battery cable from
PJ8811 on the battery board, if neces-
sary.
NOTE: On installation, be sure to route the
battery cable under the battery board to avoid
pinching the battery cable with the plastic cover.
!
To remove the HDD connector board, follow the
steps below.
1. Remove two M2x5 silver thin flat-head
screws securing the HDD connector
board.
2. Carefully lift up the HDD connector
board to disconnect it from PJ2000 on
the system board.
3. Lift out the HDD connector board.
Toshiba TRR
Page 12
7/02, Satellite
Download from Www.Somanuals.com. All Manuals Search And Download.
Satellite 1400 Series Disassembly Overview, cont.
To install the HDD connector board, follow the steps
below.
1. Seat the HDD connector board and
carefully connect it to PJ2000 on the
system board.
2. Secure the HDD connector board with
two M2x5 silver thin flat-head screws.
3. Lift out the HDD connector board.
CAUTION: Be careful not to damage or pinch the
FDD SUMI card when you seat the HDD connec-
tor board. Be sure the wireless LAN switch is in
the correct position.
To remove the RTC battery, follow the steps below.
1. Disconnect the RTC battery cable from
PJ9999 on the sound board.
2. Lift out the RTC battery.
To remove the sound board, follow the steps below.
1. Disconnect the sound SUMI card from
PJ7100 and PJ7101 on the sound board.
2. Disconnect the CD switch board SUMI
card from PJ7102 on the sound board.
3. Remove one M2.5x4 screw securing the
sound board.
4. Lift up the sound board.
To remove the CD switch board, follow the steps
below.
1. Remove four M2.5x4 black flat-head
screws securing the front cover
assembly.
2. Remove the front cover assembly.
3. Remove the CD SUMI card from PJ7300
on the CD switch board.
4. Remove two M2.5x4 black flat-head
screws securing the CD switch board.
5. Remove the CD switch board from the
front cover assembly.
!
Toshiba TRR
Page 13
7/02, Satellite
Download from Www.Somanuals.com. All Manuals Search And Download.
Satellite 1400 Series Disassembly Overview, cont.
To remove the DC-IN cable, follow the steps below.
1. Remove two M2.5x6 black flat-head
screws securing the plastic brace.
2. Remove the plastic brace.
3. Disconnect the DC-IN cable from PJ8800
on the system board.
4. Remove the DC-IN cable.
!
To remove the cooling fan, follow the steps below.
1. Remove two M2x6 screws securing the
metal brace.
2. Remove the metal brace.
3. Disconnect the power cable from
PJ8770 (S2400) or PJ770 (S1400) on the
system board.
4. Remove one M2.5x4 black flat-head
screw securing the cooling fan module.
5. Remove the cooling fan module.
6. Remove the heat sink unit, if necessary.
!
"
To remove the system board, follow the steps
below.
1. Remove three M2.5x6 black flat-head
screws securing the system board.
2. Remove the following two stud screws:
• One M2.5x6
• One M2.5x14
3. Lift up the system board from the right
side and remove it with the RJ-45 jack.
!
Toshiba TRR
Page 14
7/02, Satellite
Download from Www.Somanuals.com. All Manuals Search And Download.
Satellite 1400 Series Disassembly Overview, cont.
To remove the PC card slot, follow the steps below.
1. Lay the system board right side up.
2. Remove four M2x12 screws securing
the PC card slot.
3. Lay the system board right side up.
4. Disconnect the PC card slot from
PJ3332.
!
To remove the speakers, follow the steps below.
1. Lay the top cover and display assembly
upside down.
2. Remove four M2.5x5 screws securing
the speakers.
3. Remove the tape securing the speaker
cables.
4. Free the speaker cables from their
guides.
5. Remove the speakers.
!
!
Toshiba TRR
Page 15
7/02, Satellite
Download from Www.Somanuals.com. All Manuals Search And Download.
Satellite 1400 Series Disassembly Overview, cont.
To remove the CPU, follow the steps below.
1. Remove two M2.5x6 black screws and
two M2.5x16 black screws securing the
metal plate.
2. Remove the metal plate.
3. Remove two M2x6 screws securing the
metal brace and lift if out.
4. Lift up the heat pipe and lay it on the
insulator.
5. Turn the cam to the unlock position with
a flat-blade screwdriver to unlock the
CPU.
6. Lift up the CPU.
CAUTION: When you remove the CPU, wipe the
grease off the bottom of the heat sink, the bottom
of the cooling fan, and the top of the CPU.
!
"
#
"
To install the CPU, follow the steps below.
1. Make sure the cam is in the open
position.
2. Seat the CPU in the CPU socket. Be
sure the alignment is exact to avoid
damaging pins on the CPU.
3. Press the interposer gently with your
fingers and turn the cam on the CPU
socket to the lock position with a flat-
blade screwdriver to secure the CPU.
4. Apply new grease on the CPU.
5. Seat the heat pipe on the CPU. Be sure
the alignment is exact to avoid damaging
pins on the CPU.
6. Secure the metal brace with two M2x6
screws.
7. Seat the metal plate and secure it with
two M2.5x6 black screws and two
M2.5x16 black screws.
CAUTION: When you install the CPU, apply new
grease at the top of the chip. Be sure the bottom
of the heat pipe covers the top of the CPU.
Toshiba TRR
Page 16
7/02, Satellite
Download from Www.Somanuals.com. All Manuals Search And Download.
Satellite 1400 Series Disassembly Overview, cont.
To remove the display mask, follow the steps below.
1. Remove two mask seals at the bottom
corners of the display assembly.
2. Remove two M2.5x6 flat-head screws.
3. Release twenty-one latches on the
display mask as follows:
• Five on the bottom
• Five on each side
• Six on the top
!
To remove the FL inverter board, follow the steps
below.
1. Remove one M2x4 flat-head screw
securing the FL inverter board.
2. Rotate the FL inverter board out and
disconnect the FL cable from CN1 on the
FL inverter board.
3. Disconnect the HV cable from CN2 on
the FL inverter board.
4. Remove the FL inverter board.
To remove the LCD module, follow the steps below.
1. Remove four masking seals that cover
the screws.
2. Remove four M2x4 screws securing the
LCD module.
3. Carefully rotate the top of the LCD
module out to access the LCD/FL cable.
4. Remove the tape securing the LCD/FL
cable.
5. Disconnect the LCD/FL cable.
6. Remove the LCD module.
7. Remove four silver super flat-head
M2x3 screws securing two metal
braces.
!
!
Images continued on the next page
Toshiba TRR
Page 17
7/02, Satellite
Download from Www.Somanuals.com. All Manuals Search And Download.
Satellite 1400 Series Disassembly Overview, cont.
"
"
To remove the antenna coaxial cables, follow the
steps below.
1. Remove two M2.5x6 tapping screws
securing the metal plate.
2. Remove the metal plate and the plastic
brace.
3. Slip tweezers into the side of the plastic
brace and pry to release two latches and
remove the bottom part of the plastic
brace.
4. Remove the tape securing the wireless
LAN antenna coaxial cables.
5. Free the wireless LAN antenna coaxial
cables from their guides and remove
them.
!
To remove the LCD/FL cable, follow the steps
below.
1. Remove two M2.5x6 tapping screws
securing the metal plate.
2. Remove the metal plate and the plastic
brace.
3. Remove one M2.5x6 tapping screw
securing the metal brace.
4. Remove the LCD/FL cable.
NOTE: When you remove the top cover, hold it by
the sides close to the hinges to prevent damage.
!
"
Toshiba TRR
Page 18
7/02, Satellite
Download from Www.Somanuals.com. All Manuals Search And Download.
Satellite 1400 Series Interrupts / Memory Map
Interrupt Assignments
Interrupt
Level
Assigned to:
—
NMI
0
RAM Parity Error, I/O Channel Error
Timer
1
Keyboard
2
3
PIC 2 for level 8 to 15
COM 2/4*
1
4
COM 1/3*
5
6
LPT 2*, or Secondary IDE*
FDC
7
LPT 1/3*
8
RTC
9
Modem 2nd IRQ*
Reserved
Reserved
10
11
12
13
14
15
2
PS/2 Mouse
Math co-processor
Primary IDE*
CD-ROM (ATAPI)*
* These I/O assignments are controlled by PnP OS or system setup as shown
below:
IRQ level
0
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15
IDE
$
$
%
$
$
%
$
$
$
$
$
$
$
$
$
$
$
%
$
$
$
$
$
$
$
%
$
$
$
%
$
$
CD-ROM (ATAPI)
Serial Port
Modem 2nd IRQ
FIR
Parallel Port
PCI Bus
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
%: Default setting, $: Possible setting
System Memory Map
Address range
Space (Kbytes)
Use
'00000000' to '0009FFFF'
'000A0000' to '000BFFFF'
'000C0000' to '000CFFFF'
'000D0000' to '000EFFFF'
'00F0000' to '000FFFFF'
'00100000' to '03FDFFFF'
'03FE0000' to '03FEFFFF'
'03FF0000' to '03FFFFFF'
640
128
64
Conventional memory
Video RAM
VGA BIOS-ROM
Not used (PCI/ISA)
System BIOS ROM (Shadow RAM)
System working memory
ACPI
128
64
64,384
64
64
DMI
'04000000' to '0FFFFFFF' 196,608 (MAX.)
'0A)000000' to 'FFFDFFFF'
Optional working memory
Memory expansion in expansion port
System Management RAM and etc
BIOS-ROM (duplicated) and etc
'100A0000' to '100FFFFF'
'FFFF0000' to 'FFFFFFFF'
384
1,024
Toshiba TRR
Page 19
7/02, Satellite
Download from Www.Somanuals.com. All Manuals Search And Download.
Satellite 1400 Series Input/Output Port Assignments
Port Map
Port address
'000' to '01F'
Device/function
82C37: DMA C #1
82C59: PIC #1
Port address
'2F8' to '2FF'
'300' to '30F'
'310' to '32F'
'330' to '337'
'338' to '36F'
'370' to '375'
'376' to '377'
'378' to 37F'
'380' to '387'
'388' to '38B'
'38C' to '3AF'
'3B0' to '3BB'
'3BC' to '3BF'
'3C0' to '3DF'
'3E0' to '3E7'
'3E8' to '3EF'
'3F0' to '3F5'
'3F6'
Device/function
Serial Port* (COM 2)
Not used
'020' to '03F'
'040' to '05F'
'060' to '06F'
'070' to 07F'
'080' to '09F'
'0A0' to '0BF'
'0C0' to '0DF'
'0E0' to '0EF'
'0F0' to '0FF'
'100' to '16F'
'170' to '177'
'178' to '1EF'
'1F0' to '1F7'
'1F8' to '1FF'
'200' to'207'
'208' to '21F'
'220' to '233'
'234' to '23F'
'240' to '253'
'254' to '25F'
'260' to '263'
'264' to '26F'
'278' to '27F'
'280' to '293'
'294' to '2E7'
'2E8' to '2EF'
'2F0' to '2F7'
82C54: PIT
Not used
KBC / System Status
Not used
RTC / NMI Mask Register
DMA Page Register
82C59: PIC #2
82C37: DMA C #2
Special Register
Math Coprocessor
Not used
Not used
Not used
Secondary IDE
Parallel Port* (LPT1)
Not used
Not used
Not used
Secondary IDE*
Not Used
VGA
Parallel Port* (LPT3)
VGA
Primary IDE*
Not used
PC Card Contoller
Serial Port* (COM3)
FDC
Not used
Not used
Sound (SB Pro)
Not used
Primary IDE
FDC / Primary IDE
Serial Port (COM1)
Not used
'3F7'
Sound (SB Pro)
Not used
'3F8" to '3FF'
'400' to '47F''
'480' to '49F'
'4A0' to '52F'
'530' to '537'
'540' to '547'
'550' to '557'
'560' to '567'
Sound (SB Pro)
Not used
DMA Hi-Page Register
Not used
Parallel Port* (LPT2)
Sound (SB Pro)
Not used
Sound (WSS)
Sound (WSS)
Sound (WSS)
Sound (WSS)
Serial Port (COM4)
Not used
* These port addresses can be specified by System Setup.
Toshiba TRR
Page 20
7/02, Satellite
Download from Www.Somanuals.com. All Manuals Search And Download.
|