TDP-XP1
DATA PROJECTOR
OWNER’S MANUAL
In the spaces provided below, record the Model and Serial No. located at the bottom of
your projector.
Model No.
Serial No.
Retain this information for future reference.
Download from Www.Somanuals.com. All Manuals Search And Download.
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
- Consult the dealer or an experienced radio/TV technician for help.
RESPONSIBLE PARTY: TOSHIBA AMERICA INFORMATION SYSTEMS, INC.
9740 Irvine Blvd., Irvine, CA 92618-1697 U.S.A
Phone: (949) 583-3000
CAUTION: Changes or modifications made to this equipment, not expressly approved by
USA only
Toshiba, or parties authorized by Toshiba, could void the user’s authority to
operate the equipment.
NOTICE:
This Class B digital apparatus complies with Canadian ICES-003. Cet appareil
CANADA only numérique de la classe B est conforme à la norme NMB-003 du Canada.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
CAUTION: PLEASE READ AND OBSERVE ALL WARNINGS AND INSTRUC-
TIONS GIVEN IN THIS OWNER’S MANUAL AND THOSE MARKED
ON THE UNIT. RETAIN THIS BOOKLET FOR FUTURE REFER-
ENCE.
This unit is fully transistorized and does not contain any parts that can be repaired by the
user.
WARNING:
DO NOT REMOVE THE CABINET COVER, OR YOU MAY BE EX-
POSED TO DANGEROUS VOLTAGE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL ONLY.
1. Read Owner’s Manual
3. Source of Light
After unpacking this product, read
the owner’s manual carefully, and
follow all of the operating and
other instructions.
Do not look into the lens while the
lamp is on. The strong light from
the lamp may cause damage to
your eyesight.
2. Power Sources
4. Ventilation
This product should be operated
only from the type of power source
which does not exceed the voltage
range specified on the rating label
and the power cord. If you are not
sure of the type of power supply to
your home, consult your product
dealer or local power company.
Openings in the cabinet are pro-
vided for ventilation and to ensure
reliable operation of the product
and protect it from overheat-
ing. These openings must not be
blocked or covered. Never block
an opening by placing the product
on a bed, sofa, rug or other similar
surface. Do not place it in a built-
in installation such as a bookcase
or rack, unless proper ventilation is
provided.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Heat
8. Be sure that you firmly in-
sert the plug into the wall
outlet.
The product should be situated
away from heat sources such as
radiators, heat registers, stoves,
or other products (including ampli-
fiers) that produce heat.
Incorrect or faulty connections
may result in fire or electric shock.
Avoid using an unsound or loose
outlet.
9. Power Cord Protection
Power cords should be routed
so that they are not likely to be
walked on or pinched by items
placed upon or against them, pay-
ing particular attention to cords at
plugs, convenience receptacles,
and the point where they exit from
the product.
6. Water and Moisture
Do not use this product near wa-
ter. - for example, near a bath tub,
wash bowl, kitchen sink, or laundry
tub; in a wet basement; or near a
swimming pool and the like.
10. Overloading
7. Cleaning
Do not overload wall outlets. To
reduce the risk of electric shock,
do not use the polarized plug with
an extension cord, receptacle, or
other outlet unless the blades can
be inserted completely with three-
wire grounding type to prevent
blade exposure. Failure to follow
these instructions may result in
fire or electric shock.
Unplug this product from the wall
outlet before cleaning. Do not use
liquid cleaners or aerosol cleaners.
Always use a soft cloth for clean-
ing.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS (Continued)
11. Lightning storms
14. Do not place the product
vertically
For added protection for this
product during a storm, or when
it is left unattended and unused
for long periods of time, unplug it
from the wall outlet. This will pre-
vent damage to the product due
to lightning and power-line surges.
Never operate this unit on AC
power during a thunderstorm. If
you see lightning or hear thunder,
never touch the unit, cables and/
or peripherals. An electric surge
caused by the storm, may result in
an electrical shock or damage to
the unit.
Do not use the product in the up-
right position or any other vertical
positions to project the pictures. It
may fall which could result in seri-
ous injury and/or damage to the
product.
15. Stack Inhibited
Do not stack other equipment on
this product and do not place this
product on other equipment. The
top and bottom surface of this
product increase in temperature
during normal use and may dam-
age the other unit.
12. Object and Liquid Entry
Never push objects of any kind
into this product through open-
ings as they may touch dangerous
voltage points or short-out parts
that could result in a fire or elec-
tric shock. Never spill liquid of any
kind on the product.
16. Attachments
Do not use attachments not rec-
ommended by the product manu-
facturer. Use of an incompatible
attachments could cause hazards
or damage to the product.
13. Do not place or keep the
projector within the reach
of the children.
It may fall or tip over, possibly
causing serious injury.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
e) The product has been dropped or
damaged in any way (If the cabi-
net should break, please handle
with care to avoid injury).
f) The product exhibits a distinct
change in performance, which
indicates a need for service.
17. Accessories
Do not place this product on an
unstable cart, stand, tripod, brack-
et, or table. The product may fall,
causing serious injury to a child
or adult, and serious damage to
the product. A product and cart
combination should be moved with
care. Quick stops, excessive force,
and uneven surfaces may cause
the product and cart combination
to overturn.
19. If glass components, in-
cluding lens and lamp,
should break, contact your
dealer for repair service.
This product incorporates glass
components, including a lens and
a lamp. If these should break,
please handle with care to avoid
injury and contact your dealer for
repair service. Avoid any broken
pieces of glass since they may
cause injury. In the unlikely event
that the lamp ruptures, thoroughly
clean the area around the projec-
tor and discard any edible items
placed in that area since they may
be contaminated.
S3125A
18. Damage Requiring Service
Unplug this product from the wall
outlet and take the product to
qualified service personnel if you
encounter any of the following
conditions:
a) The power supply cord or plug is
damaged.
b) Liquid has been spilled, or objects
have fallen into the product.
c) The product has been exposed to
rain or water.
d) The product does not operate
normally when following the op-
erating instructions. Adjust only
those controls that are covered by
the operating instructions since an
improper adjustment of other con-
trols may result in damage and will
often require extensive work by a
qualified technician to restore the
product to its normal operation.
20. Servicing
Do not attempt to service this
product yourself as opening or
removing covers may expose you
to dangerous voltage or other haz-
ards. Refer all servicing to quali-
fied service personnel.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS (Continued)
21. Replacement Parts
24. Do not use the product in
a closed installation loca-
When replacement parts are re-
quired, be sure the service techni-
cian has used replacement parts
specified by the manufacturer or
have the same characteristics as
the original part.
Unauthorized substitutions may
result in fire, electric shock, or
other hazards.
tion.
Do not place the product in a box
or in any other closed installation
location. Otherwise it may over-
heat, which could result in a risk
of fire.
(Only the replacement of the lamp
should be made by users.)
22. Safety Check
Upon completion of any service
or repairs to this product, ask the
service technician to perform safe-
ty checks to verify that the product
is in proper operating condition.
23. Do not leave thermal-
paper documents or eas-
ily deformed items on top
of the unit or near the air
exhaust for long periods
of time.
The heat from the unit could erase
the information on the thermal
paper, or cause deformation or
warping.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
POWER SUPPLY INFORMATION
If your line voltage is 220 to 240V, use one of the following types of cable/plug.
Plug
Plug
configuration Plug type
Line voltage
220 240V
configuration Plug type
Line voltage
200 240V
Australian
240V
10A
EURO
Switzerland 200 240V
240V
6A
UK
220 240V
Use a 5A fuse which is approved by ASTA
or BSI to BSI362.
Always replace the fuse cover after
changing the fuse.
North American 200 240V
240V
15A
IMPORTANT PRECAUTIONS
Moisture Condensation
Never operate this unit immediately after moving it from a cold location to a warm location.
When the unit is exposed to such a change in temperature, moisture may condense on
the lens and the crucial internal parts. Do not use the unit for at least 2 hours when there
is an extreme or sudden change in temperature to prevent the unit from possible damage.
Place and Manner of Installation
• Do not place in hot locations, such as near heating equipment. Doing so could cause
malfunction, and shorten the life of the projector.
• Avoid locations with oil or cigarette smoke. Doing so will dirty the optical parts, shortening
their lives, and darkening the screen.
• Do not use this product in the upright position or tilt it up or down by more than 20° from
level. Doing so may cause a failure or shorten the life of the product.
• Using this instrument near a TV or radio may cause interference to the images or audio
sound. If this happens, move it away from the TV or radio.
• Moving the projector from a low-temperature room to a high-temperature room may cause
condensation on the lens or internal parts. If you continue to use it in that situation it may
malfunction. Wait until the condensation naturally disappears.
• In a high altitude location where air is thin, cooling efficiency is reduced so use the pro-
9
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT PRECAUTIONS (Continued)
• The set of projector is hot after use. Handle with care.
• Do not use the projector while holding it in your hands or lap.
• Do not use the projector near a power source and the like, or in locations like a ship or ve-
hicle that are subject to vibration or shock. Doing so may lead to a malfunction or shorten
service life.
• Only plug the power cord into outlets rated for use with the power cord’s specified voltage
range. Do not overload extension cords or power strips as this can result in fire or electric
shock.
• Route the power cable or the connecting cable away from where people could trip over it.
The projector may fall, which could result in severe injury.
• Be sure the power cord is easily reached for unplugging in case of emergency. Do not
place any obstacles near a wall outlet in which the cord is plugged.
Avoid Volatile Liquid
Do not use volatile liquids, such as an insect spray, near the unit. Do not leave rubber or
plastic products touching the unit for a long time, as they will leave marks on the finish.
Do not use a chemically saturated cloth.
EXEMPTION CLAUSES
• Toshiba Corporation bears no responsibility in the case of damages arising from natural
disaster such as earthquakes, lightning, etc., fire not liable to Toshiba Corporation, acts
by third parties, other accidents, or use under abnormal conditions including erroneous or
improper operation and other problems.
• Toshiba Corporation bears no responsibility for incidental damages (lost profit, work inter-
ruption, corruption or loss of the memory contents, etc.) arising from the use of or the
inability to use this unit.
• Toshiba Corporation accepts no liability whatsoever for any damages arising from not
having followed the descriptions in this Owner’s Manual.
• Toshiba Corporation accepts no liability whatsoever for any damages arising from mal-
functions arising from combination with equipment or software that is not related to
Toshiba Corporation.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
OTHER INFORMATION
Copyrights
Showing or transmitting commercial imaging software or broadcast or cable-broad cast-
ing programs with the purpose of other than the personal and private viewing, including
modifying images using the freeze functions, or displaying with the varying aspect ratio
of the images, could violate the direct or indirect copyrights of the imaging software or
broadcast program, etc., if done without first consulting with the copyright holder. For this
reason, take appropriate measures before performing one of the actions listed above, in-
cluding obtaining a license from the copyright holder.
Disposal
This product contains substances which are harmful to humans and the environment.
• The lamp contains inorganic mercury.
Please dispose of this product or used lamps in accordance with local regulations.
Following information is only for EU-member states:
The use of the symbol indicates that this product may not be treated as
household waste. By ensuring this product is disposed of correctly, you will
help prevent potential negative consequences for the environment and human
health, which could otherwise be caused by inappropriate waste handling of
this product. For more detailed information about recycling of this product,
please contact your local city office, your household waste disposal service or
the shop where you purchased the product.
Trademarks
• VGA, SVGA, XGA, SXGA, UXGA are trademarks or registered trademarks of Interna-
tional Business Machines Corporation.
• DLP (Digital Light Processing) is a registered trademark of Texas Instruments, Inc.
• Macintosh is a registered trademark of Apple Computer, Inc.
• Windows is a registered trademark of Microsoft Corporation in the U.S. and other coun-
tries.
• Adobe and Acrobat Reader are registered trademarks of Adobe Systems Incorporated.
• All other brand and product names are trademarks or registered trademarks of their re-
spective companies.
Notational Conventions Used in This Manual
• References to pages with related information are annotated as follows.
p.35
For example, if making a reference to page 35:
• The illustrations in this document are for reference purposes only and may not reflect
your package exactly.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
REMOTE CONTROL BATTERY
Warning
• Never throw a battery into a fire.
• Using the battery improperly may cause them to explode or leak and may result in seri-
ous injury. If battery-leaking fluid contacts skin, wash the fluid off immediately with clean
water and consult a doctor. If the fluid spills on an instrument, avoid contact and wipe it
off using tissue paper. Then dispose of the used tissue paper as flammable garbage after
moistening it with water.
• Keep the battery away from the reach of children. Battery is choking hazard and can be
very dangerous if swallowed. If the battery is swallowed, seek medical assistance imme-
diately.
Notes
• Be sure to use a CR2025 battery.
• Dispose of a battery in a designated disposal area.
• Check and follow your local regulations before disposal.
• Attention should be drawn to the environmental aspects of battery disposal.
• If the remote control does not operate correctly, or if the operating range becomes re-
duced, replace the battery with a new one.
• If the battery is dead or if you will not be using the remote control for a long time, remove
the battery to prevent battery acid from leaking into the battery compartment.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
Before Using
SAFETY PRECAUTIONS ..................................................................................................2
IMPORTANT SAFETY INSTRUCTIONS............................................................................4
POWER SUPPLY INFORMATION .....................................................................................9
IMPORTANT PRECAUTIONS............................................................................................9
EXEMPTION CLAUSES ..................................................................................................10
OTHER INFORMATION...................................................................................................11
REMOTE CONTROL BATTERY ......................................................................................12
CONTENTS .....................................................................................................................13
Preparations
Checking the package contents.......................................................................................15
Names of each part on the main unit...............................................................................16
Names of each part on the control panel.........................................................................17
Names of each part on the remote control.......................................................................18
Parts on the rear panel.....................................................................................................19
Preparing and using the remote control...........................................................................20
Placement ........................................................................................................................21
Connection.......................................................................................................................23
Operations
Turning the power on and off............................................................................................24
Basic operations...............................................................................................................26
Using handy features .......................................................................................................28
Using auto setting (For computer input only)................................................................28
Correcting the keystone distortion ................................................................................28
Cutting off the picture and sound temporarily (Mute)....................................................29
Freezing the image (Freeze).........................................................................................29
Resizing image .............................................................................................................30
Using the menus ..............................................................................................................31
How to use the menus..................................................................................................31
The image adjustment menu ........................................................................................32
The display setting menu..............................................................................................33
The default setting menu ..............................................................................................34
Displaying Information (Status display).........................................................................35
Maintenance
About lamp.......................................................................................................................36
Lamp replacement ...........................................................................................................37
Lens and main unit cleaning ............................................................................................39
Others
Trouble indications ...........................................................................................................40
Before calling service personnel ......................................................................................41
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications...................................................................................................................42
List of general specifications..........................................................................................42
Separately sold product................................................................................................42
List of supported signals (RGB signals) .......................................................................43
List of supported signals (Component signals).............................................................44
List of supported signals (Video, S-Video signals) .......................................................44
CONTROL terminal ......................................................................................................45
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Checking the package contents
Please make sure that the following items are included in the box, along with the main unit.
If any item is missing, immediately contact the store where you purchased the product.
(1)
(2)
(4)
(5)
(3)
(6)
(1) Remote control
(2) CD-ROM
(5) Power cord (See note below)
(6) Carrying bag
(3) Owner’s Manual (This document)
(4) RGB cable (3m)(See note below)
Note
• The shape and number of supplied power cords vary depending on the product
destination.
• To maintain original performance, always use the supplied cables.
Save Original Packing Materials
The original shipping carton and packing materials will come in handy if you ever have to
ship your projector. For maximum protection when shipping your projector, repack the set
as it was originally packed at the factory.
The Supplied CD-ROM
The supplied CD-ROM contains an owner’s manual in Portable Document Format (PDF).
Please use Acrobat Reader 5 or later version to view the manual.
Adobe® Acrobat® Reader®or Adobe® Reader®
The supplied CD-ROM does not contain Acrobat® Reader®. If you cannot read PDF
files, please install Adobe Reader software in your computer by downloading it from the
Adobe Systems website.
Viewing the manual
Run the CD-ROM and double-click on Start.pdf. Acrobat® Reader® launches, and the
menu screen of the Owner’s manual appears. Click on your language. The Owner’s
Manual cover and list of bookmarks appear. Click on a bookmark title to view that sec-
p.
tion of the manual. Click on
to view a reference page with related information.
See the Help menu for more information about Acrobat® Reader®.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Names of each part on the main unit
(2)
(7)
(6)
(5)
(4)
(3) (1)
(8)
(5)
(9) (10)
(11)
(12)
(13)
(14) (15)
Back
Front
Name
: Function
(1) Lens
(2) Infrared remote sensor
: Projects expanded image.
(3) Foot adjuster release button : Press to set up or stow the foot adjuster.
(4) Air exhaust
(5) Air intake
: Expels air that has grown hot inside the projector.
: Draws in air from outside the projector for internal cool
down.
(6) Control panel
(7) Zooming ring
(8) Speaker
: Operates the projector.
: Adjusts screen size.
: Outputs audio sound.
(9) AC IN socket
: Connect the supplied power cord here.
(
(
(
(
(
(
10) Rear panel
: Connects external devices.
11) Antitheft lock slot
12) Tilt adjuster
13) Lamp cover
14) Foot adjuster
15) Focusing ring
: Attach a safety cable or any other antitheft device.
: Adjusts the projector’s horizontal tilt.
: Remove to replace lamp.
: Adjusts the vertical projection angle.
: Adjusts screen focus.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Names of each part on the control panel
(1) (3)
(2) (1)
(8)
(7)
(4) (9) (5)
(6)
Name
: Main Function
Control panel
(1) VOL +/- button
(2) ENTER button
(3) KEYSTONE +/- button
(4) Selection buttons
(5) INPUT button
(6) ON/STANDBY button/
indicator
: Adjusts the volume.
: Accepts the selected mode.
: Adjusts keystone distortion.
: Menu selections and adjustments.
: Selects input source.
: Turns the power on/off (standby).
: Displays power on/off mode.
(7) MENU button
(8) TEMP indicator
(9) LAMP indicator
: Displays menus.
: Lights when internal temperature is too high.
: Displays lamp mode.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Names of each part on the remote control
Remote control
transmitter
(5)
(6)
(3)
(4)
(1)
(7)
(2)
(1)
(3)
(10)
(9)
(11)
(9)
(8)
Name
: Main Function
(1) VOL +/- button
(2) ENTER button
(3) KEYSTONE +/- button
(4) Selection buttons
(5) INPUT button
(6) ON/STANDBY button
(7) MENU button
: Adjusts the volume.
: Accepts the selected mode.
: Adjusts keystone distortion.
: Menu selections and adjustments.
: Selects input source.
: Turns the power on/off (standby).
: Displays menus.
: Pauses image.
(8) FREEZE button
(9) RESIZE buttons
: Enlarges images.
(
10) Auto-Set button
: Performs auto-adjustment of input signals from computer.
(
11) MUTE button
: Cuts off the picture and sound temporarily.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts on the rear panel
(1)
(2) (3) (4) (5)
(6)
(7)
(8)
(9)
Name
: Main Function
(1) COMPUTER IN terminal
: Input analog RGB signal from a computer or other
source, or a component video signal (Y/PB/PR) from
video equipment.
(2) S-VIDEO terminal
(3) VIDEO terminal
(4) AUDIO IN terminal
(5) AUDIO OUT terminal
(6) MONITOR terminal
(7) CONTROL terminal
: Input S video signals from video equipment.
: Input video signals from video equipment.
: Input audio signals.
: Outputs audio signals.
: Connect to a computer display, etc.
: When operating the projector via a computer, connect
this to the controlling computer’s RS-232C port.
(8) AC IN socket
: Connect the supplied power cord here.
(9) Antitheft lock slot
: Attach a safety cable or any other antitheft device.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Preparing and using the remote control
■ Loading a coin cell battery
into the remote control
j Remove the battery holder.
■ Operating the remote
control
Point toward the projector’s
infrared remote sensor, and press a
button on the remote control.
• Operating the projector from the front
Hold down the side release firmly and pull
out the battery holder.
Approx.15
A
p
p
r
o
k Load a coin cell battery (CR2025).
x
.
7
m
Be sure to align the plus and minus ends
of the battery properly.
5
2
0
T
2
L
R
O
C
V
3
Notes
• When you use for the first time after
purchase, a plastic sheet is provided
between the battery and its contact. Be
sure to remove by pulling it off.
l Replace the battery holder back
into the remote control.
• When operating the remote control from
behind the projector, the infrared beam
is reflected on the projecting surface and
may travel a shorter distance to reach
the projector depending on the shape
and material of the projecting surface.
5
2
0
2
T
L
R
O
C
V
3
Coin cell battery
• Before using the battery, be sure to observe the Safety Precautions described in previous
pages.
• Remove the battery from remote control when not using for extended periods.
• If the remote control stops working, or if its range decreases, replace the battery with a
new one.
• Keep the battery away from the reach of children. Battery is choking hazard and can
be very dangerous if swallowed. If the battery is swallowed, seek medical assistance
immediately.
The remote control
• The remote control may fail to operate if the infrared remote sensor is exposed to bright
sunlight or fluorescent lighting.
• Do not drop or bang.
• Do not leave in hot or humid locations.
• Do not allow it to get wet or place it on top of wet objects.
• Do not take apart.
• In rare cases, ambient conditions could impede the operation of the remote control. If this
happens, point the remote control at the main unit again, and repeat the operation.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Placement
Placement Styles
As shown in the figures below, this device can be placed in 4 different styles.
The factory setting is “floor-mounted front projection.” Set the [Projection mode] in the
, in accordance with your needs.
Floor-mounted front projection
Floor-mounted rear projection
Ceiling-mounted front projection
Ceiling-mounted rear projection
WARNING
• Always obey the instructions listed in IMPORTANT SAFETY INSTRUCTIONS when placing
the unit. Attempting to clean or replace the lamp in a high location by yourself may cause you to fall,
resulting in injury.
• If you wish to mount the projector on the ceiling, be sure to ask your dealer to do so. Mounting
the projector on a ceiling requires special ceiling brackets (sold separately) and specialized knowledge.
Improper mounting could cause the projector to fall, resulting in an accident.
• If the projector is ceiling-mounted, install the breaker for turning off the power in case of
anomaly. Let everyone involved with the use of the projector know that fact.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Placement (Continued)
Projection Distance and Size
Use the figures, tables, and formulas below to determine the projection size and projection
distance. (Projection sizes are approximate values for full-size picture with no keystone
adjustment.)
As seen from above
Screen
projection
size
(inches)
Wide
Tele
Offset
distance
distance
height (H)
(m)
(feet)
(m)
1.00
(feet)
(cm)
(feet)
90
23.9
30
---
1.15
1.56
2.37
3.18
3.98
5.99
7.97
9.93
11.88
---
3.77
3.28
4.19
5.5
6.9
0.18
0.23
0.30
0.45
0.60
0.75
1.13
1.50
1.88
2.25
1.28
1.73
2.62
3.52
4.41
6.62
8.82
10.99
---
40
5.10
5.66
9.1
60
7.77
8.60
13.7
18.3
22.9
34.3
45.7
57.2
68.6
As seen from the side
80
10.43
13.07
19.64
26.15
32.59
38.97
11.53
14.46
21.72
28.93
36.07
---
Lens center
100
150
200
250
300
H
90
a
a is the distance (cm, feet) between the lens and the screen, and corresponds to a range of
1 m to 11.88m (3.28 ft. to 38.97 ft.). H is the height (cm, feet) from the image bottom to the
center of the lens.
min length
a(cm)= -0.000381 x projection size (inches)2 + 4.1 x projection size (inches) - 7.8
a(feet)= -0.0000125 x projection size (inches)2 + 0.135 x projection size (inches) - 0.256
max length
a(cm)= -0.000365 x projection size (inches)2 + 4.52 x projection size (inches) - 7.7
a(feet)= -0.000012 x projection size (inches)2 + 0.148 x projection size (inches) - 0.253
height
H(cm)= projection size (inches) x 0.2286
H(feet)= projection size (inches) x 0.0075
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Connection
Before connection
• Read the owner’s manual of the device you are connecting to the projector.
• Some computers cannot be used with or connected to this projector.
Check for an RGB output terminal, supported signal
• Turn off the power of both devices before connecting.
• The figure below shows sample connections. This does not mean that all of these devices
can or must be connected simultaneously.
Monitor
Computer (for control)
Video recorder,
DVD player, etc.
To audio output
To video output
To RS-232C
terminal
Audio cable (not supplied)
Control cable
Video cable
(not supplied)
RGB cable
(supplied)
Audio cable
(not supplied)
S-Video cable
(not supplied)
Computer
To audio input
To RGB output
To S-video output
Video recorder,
DVD player, etc.
Audio amplifier, etc.
Notes
• Moving pictures played back on computers using DVD software may appear unnatural
when projected with this projector. However, it is not a malfunction of the projector.
• When an AUDIO OUT terminal is connected, sound is not output from the projector
speaker.
• Output volume of AUDIO OUT terminal can be adjusted by the VOL+/- button.
• The MONITOR OUT terminal outputs analog RGB signals or component video signals
(Y/PB/PR) from the COMPUTER IN terminals.
• A computer monitor usually cannot accept Y/PB/PR signals correctly.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Turning the power on and off
■ Connecting the power cord
Insert the power cord connector into
the AC IN socket of the projector.
1
Insert the power cord plug into a
wall or other power outlet.
2
Power cord connector
(Supplied)
■ Removing the lens cover
Be sure to remove the lens cover when the power is
turned on. If the cover is left on the projector, it could
become deformed due to heat.
Remote
Control
■ Turning the power on
Control panel
Press the ON/STANDBY
button.
Start-up screen
1
The power is turned on, and the ON/
STANDBY indicator lights green. After
a moment, the start-up screen ap-
pears.
CAUTION
• Do not look into the lens while the lamp is on. The strong light from the lamp may cause
damage to your eyesight.
• Do not block the air intake or exhaust. Doing so could cause a fire due to internal overheat-
ing.
• Do not place your hands, face, or other objects near the air exhaust, the lamp cover or
the bottom of the unit. Doing so could result in injury and/or damage the object.
Notes
• The start-up screen will disappear after a moment.You can also configure the system to
prevent the start-up screen from appearing. To do this, use the Default setting menu
• The first time you use the projector after purchase, after the start-up screen disappears,
the start menu is displayed
• Do not touch the lens directly with your hand. If fingerprints or stains are left on the
projection lens surface, they may interfere with the projector’s ability to project images on
the screen.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
■ Turning the power off
Press the ON/STANDBY button.
1
A message appears on the screen, confirming that you wish to shut off the power. To
shut off the power, press the ON/STANDBY button again. If you do not wish to shut off
the power, wait for a while without conducting any operations. The message will disap-
pear shortly. (This operation is no longer valid after the message disappears.)
Press the ON/STANDBY button again.
The screen turns off, but the internal cooling fan continues to operate for a short while.
Then, the projector goes into standby mode.
2
When cooling lamp
After cooling complete
FLASH
A
B
During cooling ,the ON/STANDBY indicator flashes. In this state, the power can-
not be turned back on.
A
However, there is no problem with unplugging the power cord in this state.
In standby mode
B
Note
• The projector consumes about 6W of power in standby. We recommend that you unplug
the power cord if you will not be using the projector for an extended period.
Precaution
• If the power cord is unplugged before cooling is complete, give the lamp time (about 5
minutes) to cool before plugging it back in. If the lamp overheats, it may fail to light.
• Right after turning off the power, the unit may become very hot, especially air exhaust
and the bottom of the unit. Please handle with care to avoid burn injuries.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic operations
Turn on the power.
1
2
Select the language (When using the first time).
When the projector is used for the first time after purchase, the start menu for lan-
guage (to display the menus and messages on screen) and configuration is displayed
in English. (if the screen is out of focus, adjust it according to the step .)
6
Use the
,
,
or
button to select the desired language and
press the
button.
Message for setup confirmation is displayed in a selected language.
English
French
Traditional Chinese
Polish
German
Italian
Spanish
Indonesian
Norwegian
Finnish
Czech
Hungarian
Greek
Portuguese
Russian
Swedish
Turkish
Danish
Romanian
Simplified Chinese
Dutch
Notes
• When the projector is turned on the next time, the start menu does not appear upon
startup.
• This owner’s manual assumes that English has been selected.
Activate the connected device.
3
4
Turn on and start the connected device such as a computer.
Press the INPUT button.
An image of the connected equipment is projected.
Each time you press the INPUT button, it switches to another source signal from the
equipment which is connected to the projector.
Notes
(factory
setting is [On]), the input is switched to the connected equipment that is outputting video
.
• Right after the input source is switched to the other, the color of the image may change
slightly.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Projector placement angle adjustments
The placement angle and the height of the projected image can be adjusted by the foot
adjuster.
5
1
j Lift up the front of the projector to
the desired angle, then press the
foot adjuster release button.
The foot adjuster extends. Release the but-
ton to lock the position.
2
k To adjust the horizontal angle, use
the tilt adjuster.
To stow the foot adjuster, hold up the projector
while pressing the foot adjuster release button,
then slowly lower the projector.
1
Adjusting the screen size and focus
6
7
j
Use the zooming ring to adjust the screen size.
2
k Use the focusing ring to adjust the focus.
Adjusting the volume with VOL+/- buttons
The speaker volume can be adjusted when an audio signal is being input.
Notes
• Lamp characteristics may rarely cause the brightness to fluctuate slightly.
• A lamp is consumable item. If used for extended periods, images will appear dark, and
the lamp could burn out. This is characteristic of a lamp, and is not malfunction. (The
lifetime of the lamp depends on conditions of use.)
• The DLP® chip is made using extremely advanced technology. There may be black spots
(pixels that do not light) or bright spots (pixels that are constantly lit) on the panel. These
are intrinsic characteristics of the technology and are not malfunctions.
• Although this projector supports a wide range of RGB signals
, any resolutions not
supported by this projector (XGA) will be expanded or shrunk, which will affect image
quality slightly. To view high-quality images, set the computer’s external output to XGA.
• With some models of computer having LCD displays or the like, displaying images
simultaneously on the projector and the monitor’s display may prevent the images from
displaying properly. If this happens, turn off the computer’s LCD display. For information
on how to turn off the LCD display, see the computer’s owner’s manual.
• If no signal is being input from the connected equipment or signal input is stopped while
projecting, the “No signal” message will appear.
• If a signal not supported by the projector is input, the “Unsupported signal” message
will appear.
• If an unavailable operation button is pressed, the
icon will appear.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Using handy features
■ Using auto setting (For computer input only)
Remote
Control
This function automatically sets up the projector to the optimum
state. It sets up sampling phase, frequency and screen position for
each type of the input signal by using simple operations.
Press the remote control’s AUTO SET button.
The
icon will appear during processing.
Notes
• The image may not be projected or auto adjustment/setting may
not be performed correctly for input signals other than those
supported by the projector
■ Correcting the keystone distortion
When the projector placement angle against the screen is changed while projecting the
image, the picture will undergo keystone (trapezoidal) distortion.
This projector is capable of correcting this keystone distortion
.
Before correction After correction
Remote
Control
Control panel
Press the KEYSTONE +/- button.
You can also select [Keystone] in the Image
Notes
• Depending on the amount of keystone adjustment and the content
of images, some information may be lost, or the picture quality may suffer.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
■ Cutting off the picture and sound temporarily (Mute)
When you want to project the images of another projector, overhead
projector, etc. temporarily, this projector’s images and sound can be
turned off.
Remote
Control
Press the remote control’s MUTE button.
The picture and sound are cut off. (The Mute function is released
when pressing the MUTE button again.)
Notes
• The
icon will appear while mute is in effect.
• Operating any other functions will also cancel the muting.
■ Freezing the image (Freeze)
The projected image can be frozen. This function is used to pause a
video during a presentation, etc.
Remote
Control
Press the remote control’s FREEZE button.
The picture pauses. (The Freeze function is released by pressing
the FREEZE button again.)
Notes
• The
icon will appear while freeze is in effect.
• Other operations will also release the freeze.
• Although an image is frozen on the projector, the pictures are
running on the video or other equipment.
• If you use this function on commercial video software, broadcast
or cable-broadcasting except for the purpose of your private
viewing and listening, it may infringe the copyright protected by
the copyright laws.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Using handy features (Continued)
■ Resizing image
The projected image can be resized (zoomed in/out).
Press the remote control’s RESIZE
button.
1
Each time you press the RESIZE
pressing.
button, zoom ratio is up.You can keep
Remote
Control
To zoom out, press the remote control’s RESIZE
button.
2
3
Each time you press the RESIZE
button, zoom ratio is
down.You can keep pressing. (However, the image cannot be
smaller than the original size.)
1
2
To move the area to zoom in, use the
buttons.
3
4
You can keep pressing.
When the image returns to the original size by pressing RESIZE
button several times, the zoom will be reset.
Notes
• The
icon appears while resizing.
• Operating a function other than Mute will release resizing.
• As zooming is processed digitally, the image quality is degraded in larger zoom ratio.
• During resizing or moving the zooming area, the image may be distorted.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the menus
You can call up on-screen menus, and conduct a number of adjustments and settings using
the operation buttons
■ How to use the menus
The menu shown below is for operation instructions purposes and might differ from the
actual display.
Display the Setting display menu.
1. Press the MENU button
2. Select a Category
Select a category by using
.
There are following 4
categories:
Displays the current
adjustments and settings of
selected category.
Image adjustment menu
Item shown with gray cannot
be adjusted with the current
input source.
Display setting menu
Default setting menu
Status display menu
3. Adjustments & Settings
Press the
or
button .
Item
Adjustment/Setting Value
These marks signify
the items can be
adjusted/set by using
5. End
Press the MENU
.
button
The menu disappears.
These marks signify the items can
be selected from the list by using
.
After an item is selected, apply it by
pressing
The figure shows displays given for operation instructions purposes. As the display may
differ depending on the item, use the information in this manual as a reference.
4. Back
MENU button
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the menus (Continued)
■ The image adjustment menu
Use this menu to set or adjust image-related items. Items that can be set or adjusted are
marked “Yes”, and those that cannot are marked “No”. (When an item is masked, it indi-
cates that you cannot select for the current input.)
Description
RGB
Yes
Y/PB/PR
Yes
Video S-video
Item
Toggle the picture mode with
/
Yes
Yes
Picture mode
Bright/Standard/True color(RGB)
Standard/Cinema(Y/PB/PR,Video, S-video)
Yes
Yes
Yes
Correct the keystone (trapezoid) distortion of the
screen.
Yes
Keystone
Screen shrinking
Screen shrinking
at bottom
at top
Adjust the brightness of the image.
Darker Brighter
Yes
Yes
Yes
Yes
Brightness
Adjust the image contrast.
Lower Higher
Adjust the color of the image.
Lighter Deeper
Adjust the tint of the image color.
Reddish Greenish
Adjust the sharpness of the image.
Softer Sharper
Adjust the horizontal position of the image.
Move left Move right
Adjust the vertical position of the image.
Yes
No
Yes
Yes
No
Yes
Yes
Yes
Yes
No
Yes
Yes
Yes
Yes
No
Contrast
Color
Tint *1
No
No
Yes
No
Sharpness
H-position
V-position
Yes
Yes
No
No
No
Move down
Adjust with
Adjust with
Move up
Yes
Yes
No
No
No
No
No
No
to eliminate flicker.
Phase
to eliminate periodic patterns
Frequency
and flickering when fine vertical lines appear on
the screen.
*1: [TINT] can be displayed and adjusted only when the video signal is set to [NTSC] and [NTSC4.43].
32
Download from Www.Somanuals.com. All Manuals Search And Download.
■ The display setting menu
Use this menu to set screen display-related items.
(The items in gray color cannot be set with the current input selection.)
Description
Item
Screen size
Screen size setting.
(Full): Display with 1024 × 768 dot resolution
(Wide): Wide-screen display
(Thru): Display with sampling resolution
Up/down
Adjust the vertical position of 16:9 image
Lower
Higher
shift
Back-
ground
Screen to display when there is no input signal
(Logo)
(Blue)
(Black)
Icon
Display icons as function guides
On
Off
No
Reset all
Press
.
Resets all adjustments and settings to their factory settings.
Yes
Detailed description
[Screen size]
• If “Thru” is selected for [Screen size], portions exceeding the native resolution
(1024 × 768 pixels) will not appear on the screen. Note that for RGB signals with
clock frequency 110MHz or lower, all input pixel signals are properly sampled.
However, if the clock speed is higher than this, the RGB pixel signal is thinned
before sampling.
• If you use the screen size setting function on commercial video software,
broadcast or cable-broadcasting programs to display images with the varying
aspect ratio except for the purpose of your private viewing and listening, it may
infringe the copyright protected by the copyright laws.
[Background]
• TOSHIBA is set for [Logo] by factory setting.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the menus (Continued)
■ The default setting menu
This menu shows placement status and other settings.
Description
Sets projection mode in accordance with Placement Style.
Item
Projection
mode
(Ceiling)
(Rear ceiling)
(Standard)
(Rear)
Auto input
search
Sets whether the input source with signals is only selected or not.
On
Off
Language
Select one of the languages below to use for displaying the menu
and messages
[
: Enter setting mode]
English/Français/Deutsch/Italiano/Español/Português/
Svenska/Türkçe/Română/ /Polski/
[
:Selection] [Apply:
]
/
/
Bahasa Indonesia/Norsk/Suomi/Čeština/Magyar/Ελληνικά/Dansk/
Nederlands
Start-up
screen
Sets whether the start-up screen displays when power is turned on.
On
Standard
Standard
Off
Fan mode
Sets the cooling fan speed.
Sets the lamp power.
High
Lamp
power
Low
Power on
Sets whether to turn on the power when the ON/STANDBY button is
pressed (Manual), or when the power cord is plugged in (Auto).
Manual
Auto.
Detailed description
[Auto input search]
Automatically searches the input source that can be projected, and switches source
from the connected device each time the INPUT button is pressed. If the connected
device outputs no source signal, the input is skipped. When the source signal is
stopped during projecting, it will switch to the other inputs automatically. If no input
sources are detected, it will stop searching and “No signal” message will appear.
[Fan mode]
Setting [Fan mode] to [High] increases the cooling fan speed. (The cooling fan
noise gets louder.) Set this option to use the projector, for example, at high altitude
(over 1,500m or 5000 ft. above sea level).
[Lamp power]
When [Lamp power] is set to [Low], the screen becomes a little darker, but the
cooling fan noise gets quieter.
[Power on]
If [Power on] is set to [Auto] and there is a power outage, the projector will come
on once power is restored.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
■ Displaying Information (Status display)
This displays information about the input signal, lamp use time, etc.
“Yes”: displayed, “No”: not displayed
Item
Description
Input source name
Resolution (in dots) [Note 1]
Color method of video signal
Picture mode setting
Time of lamp use [Note 2]
Firmware version [Note 3]
Computer Y/PB/PR
Video
Yes
No
S-video
Yes
No
Input
Yes
Yes
No
Yes
No
Resolution
Video mode
Picture mode
Lamp time
Version
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Notes
1: The Resolution of supported RGB signals
is shown.
2: Displays [Lamp time] as a measure of when the lamp should be replaced. (Cannot be used as
a counter of guaranteed lamp time.) When the displayed time approaches 3,000 hours, consult
with a dealer about getting a TLPLV10 replacement lamp (sold separately) prepared.
3: [Version] shows the version of the projector’s internal control program. This firmware version
will be requested for customer service purposes.
Note
• The displayed information will not be refreshed if the status changes. To refresh the
information, dismiss the display, then display it again.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
About lamp
The product’s light source is a mercury lamp that lights at increased internal pressure. Be sure
to fully understand the following characteristics of the lamp and handle it with extreme care.
• The lamp may burst with a loud noise due to impact or deterioration, or fail to light at the
expiration of its life.
• How long it takes before the lamp bursts or the life expires may vary greatly by lamp.
Some may burst shortly after first use.
• Burst is likely to happen if the lamp is used after the replacement period has elapsed.
• When the lamp bursts, the broken pieces of glass may get inside the product or be
released outside from the openings for ventilation.
• When the lamp bursts, a slight amount of mercury gas enclosed in the lamp along with
glass dust may be released from the openings for ventilation.
■
Immediately replace the lamp when a replacement message
appears on the screen.
• When the replacement time approaches, a message will appear on the screen.
• The risk of burst will increase if the lamp is continuously used without being replaced.
• Frequently check the used hours and prepare spares when the replacement time
■
When the lamp is broken
• If glass components, including a lamp and a lens, should break, handle the broken
pieces with care to avoid injury and contact your dealer for repair service.
• In the event of lamp burst, unplug the product from the wall outlet, leave and completely
ventilate the room. Then, thoroughly clean the area around the projector and discard any
edible items placed in that area, as they may be contaminated.
• When the lamp bursts, consult a doctor if glass dust or mercury gas gets into your eyes
or is inhaled.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Lamp replacement
A lamp is consumable supply. If used for extended periods, images will appear dark, and the
lamp could burn out. This is characteristic of a lamp, and is not malfunction. (The lifetime of
the lamp depends on condition of use.) If this happens, replace it with a new one
.
WARNING
•
If the projector is mounted on the ceiling, it is recommended to use your Toshiba dealer-
ship when the lamp has to be exchanged.
Uncovering the lamp while the projector is mounted on a ceiling may lead to a danger
of damage from falling pieces of glass if the lamp is broken. Besides, working at high
elevations can also be hazardous. Do not attempt to replace the lamp by yourself.
• When replacing, always use lamp “TLPLV10” (sold separately). If the lamp other
than the specified one is used, it may cause a malfunction or damage to the unit due
to the difference in the connector shape or the lamp rate.
CAUTION
•
•
If you have been using the projector, the lamp will be very hot, and may cause burn
injuries
.
Wait for the lamp to cool (for longer than 1 hour) before replacing it.
If the lamp should break, please handle with care to avoid injury due to broken
pieces and contact your dealer for repair service.
Unplug power cord.
1
2
Wait until lamp is sufficiently cooled.
Wait for at least 1 hour.
Lamp cover
Remove the lamp cover.
Loosen the two screws, raise the lamp cover
3
3
1
with your fingers as shown to remove the lamp
cover. Use care to avoid any damage to nails
and/or tip of your finger(s). If you have any dif-
ficulty in removal, you can use a screwdriver or
2
any other smaller tool for your convenience.
1
4
Pull out the lamp.
Loosen the two screws holding the lamp in place,
and pull up the handle to remove the lamp.
4
2
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Lamp replacement (Continued)
5
Mount the new lamp.
Align the orientation, press down the new lamp
until the bottom is reached, and lock in place using
the two lamp locking screws.
5
2
1
Replace the lamp cover.
Align the cover, and press it in, then tighten the
6
7
screws loosened in step
until the lamp cover
3
is no longer loose. (Be sure to replace the lamp
cover.)
Reset the lamp time.
See the lamp’s manual for instructions on resetting
the lamp time.
Notes and Precautions
• The [Lamp time] item in the Status display menu indicates the time of lamp use (as a
rough guide).
• It is recommended that the lamp be replaced after 3,000 hours of use.When [Lamp
time] reaches 3,000 hours, a message will appear. (After 3,000 hours, the message will
appear when the power is first turned on after each 100 hour period of use.) This display
disappears when you press the
button.
• Attach the lamp cover correctly so that it is not loose. If it is not attached correctly, the
projector may fail to be powered on or the lamp may fail to come on.
• Always replace the lamp with a new one.
• The lamp is made out of glass. Do not touch the glass surface with your bare hands,
bang it, or scratch it. (Dirt, jolts, scratches and the like could break the lamp.)
Used Lamps
This projector’s lamps contain trace amounts of environmentally harmful inorganic mer-
cury. Be careful not to break used lamps, and dispose of them in accordance with local
regulations.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Lens and main unit cleaning
WARNING
•
Request cleaning and maintenance of a ceiling-mounted unit from your projector
dealership
.
Attempting to clean or replace the lamp in a high location by yourself may cause you
to fall, resulting in injury.
■ Lens cleaning
• Clean the lens with a commercially available blower and/or
lens cleaner.
• The lens is easily scratched, so do not rub it with hard objects,
or strike it.
■ Main unit cleaning
• Unplug the power cord before cleaning the main unit.
• Wipe dirt off the main unit gently with a soft cloth.
• Do not wipe the main unit with a damp cloth. Doing
so may allow water to get inside, resulting in an
electric shock or unit failure.
• Do not use benzene, thinner and the like as they
may deform or discolor the unit or damage the paint
surface.
• Do not use a chemically saturated cloth.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Trouble indications
The indicator lights to inform you of interminal abnormalities.
No power
⇒ Problem with projector
• Unplug the power cord, and contact your dealer.
(Off)
Lamp went out during use, or won’t come on
⇒ Lamp temperature is high so that it is difficult to turn on, the lifetime of
(Red lit)
the lamp has ended or the projector is malfunctioning.
• Unplug the power cord and wait for a short while, then turn the power
back on.
(Red lit)
• If a lamp burns out, replace it with a new one.
❈ After approx. 5 second of abnormal display, the projector returns to
the standby state waiting for internal cool down.
Power went out during use
⇒ Internal overheating, or the outside temperature is too high.
• Place the projector so that the air intake and exhaust are not blocked.
• Unplug the power cord and wait for a short while, then turn the power
back on.
(Red lit)
(Red lit)
❈ The
icon will appear before the power goes out.
❈ After approx. 5 second of abnormal display, the projector returns to
the standby state waiting for internal cool down.
(Red flashing)
(Red lit)
Power went out during use
⇒ Problem with internal cooling fan.
• Unplug the power cord, and contact your dealer.
❈ The
icon will appear before the power goes out.
❈ After approx. 5 second of abnormal display, the projector returns to
the standby state waiting for internal cool down.
Power went out during use
⇒ Problem inside the projector.
(Red flashing)
(Red lit)
• Unplug the power cord and wait for a short while, then turn the power
back on.
• If the above action will not clear the problem, unplug the power cord,
and contact your dealer.
❈ The
icon will appear before the power goes out.
❈ After approx. 5 second of abnormal display, the projector returns to
the standby state waiting for internal cool down.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Before calling service personnel
If you think something is wrong, check the followings before contacting customer service.
Please see “Trouble indications”
as well.
If This Happens
Check
No power
• Is the power cord plugged in? Is it connected to the projector?
• Is the lamp cover attached properly?
Power goes out • Is the ambient temperature high?
during use
• Is the air intake or air exhaust blocked?
No picture
• Is the input source selected correctly? (When [Auto input search] is
[Off])
• Is the mute function on?
• Is the brightness setting minimized?
• Are the connections set up correctly?
• Are all the connected devices functioning properly?
No audio
• Is the mute function on?
• Is the volume setting minimized?
• Are the connections set up correctly?
• Are all the connected devices functioning properly?
Picture not
displayed
correctly
• Is the input signal supported by the projector?
,
• Is there something generating an abnormal video signal, for
instance the video tape?
Picture blurred
Part of picture
out of focus
• Is the lens dirty?
• Is the lens focus adjusted optimally?
Is the projection distance within the projector’s supported range?
•
• Is the projector’s screen placement angle tilted too far?
• Are the sharpness or sampling phase adjustments off?
Image is dark
• Are the brightness or contrast adjustments off?
• Is the lamp nearing the end of its service life?
Colors too light • Are the color, tint adjustments off?
Bad shading
• Is the screen dirty?
• Is the lamp nearing the end of its service life?
Remote control
doesn’t work
• Is the remote control’s battery drained?
• Is the battery inserted into the remote control correctly?
• Is the remote control being used within the effective range?
Are there any obstructions between the remote control and projector?
•
• Are there any fluorescent or other bright lights shining at the
projector’s infrared remote sensor?
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
■ List of general specifications
Item
Specification
Consumption Power
Weight
280 W
2.2 kg
External Dimensions
(including protruding parts)
270 x 98 x 198 mm (W x H x D)
Cabinet material
PC resin
Conditions for usage environ-
ment
Temp: 5°C to 35°C; relative humidity: 80%
Display pixels
Picture elements
Lens
1 DLP® chip
786,432 pixels (1024H × 768V)
Zoom lens
F=2.4-2.6 f=21.81-23.77 mm
Lamp
High-pressure mercury lamp (200 W)
23.9-300 inches
Projection screen size
Projection distance
Speaker
1.0m - 11m
2 W
CONTROL terminal
RS-232C: D-Sub 9 pin
COMPUTER(Y/PB/PR)
IN terminal
Mini D sub 15 pin Analog RGB / Y/PB/PR (dual use)
VIDEO terminal
S-VIDEO: Mini DIN 4 pin
VIDEO: RCA Pin Jack
AUDIO: 3.5mm dia. stereo mini-jack
Mini D sub 15 pin RGB / Y/PB/PR (dual use)
3.5mm dia. stereo mini-jack
MONITOR terminal
AUDIO OUT terminal
Notes
• This model complies with the above specifications.
• Designs and specifications are subject to change without notice.
• This model may not be compatible with features and/or specifications that may be added
in the future.
■ Separately sold product
Replacement Lamp
Model: TLPLV10
42
Download from Www.Somanuals.com. All Manuals Search And Download.
■ List of supported signals (RGB signals)
This projector supports the following RGB signals. Note, however, that depending on the
computer model, the screen may show flicker or streaking. Please adjust the projector if
this happens.
Refresh rate H-frequency
Clock
(MHz)
25.17
31.5
31.5
36
32
35.5
36
40
50
49.5
56.25
65
Resolution
Mode
[Hz]
59.94
72.8
75
[KHz]
31.46
37.86
37.5
VGA_60
VGA_72
VGA_75
640x480
VGA_85
85
70
43.26
31.5
720x400_70
720x400_85
SVGA_56
SVGA_60
SVGA_72
SVGA_75
SVGA_85
XGA_60
720x400
800x600
85.03
56.25
60.3
72.18
75
37.92
35.15
37.87
48.07
46.87
53.67
48.36
56.47
60.02
68.67
63.98
63.85
67.5
85.06
60
XGA_70
XGA_75
XGA_85
70.06
75.02
84.99
60.02
70
75
1024x768
78.75
94.5
108
90.3
108
108
57.28
79.85
81
1280x1024
1152x864
1280x1024_60
1152x864_70
1152x864_75
1280x960_60
MAC 16”
75
1280x960
832x624
1024x768
1152x870
640x480
60
60
74.55
75
75.06
60
49.725
60.24
68.68
31.35
60
MAC 19”
MAC
MAC G4
i Mac DV
40
79
80.05
1024x768
1152x870
75
i Mac DV
75
68.49
Note
• Signals of which resolution exceeds the native resolution (1024 × 768 pixels) will be
compressed. For this reason, some information may be lost, or image quality may be
affected.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications (Continued)
■ List of supported signals (Component signals)
Signal format
fh(kHz)
15.73
31.47
15.63
31.25
45.00
37.50
33.75
28.13
fv(Hz)
59.94
59.94
50.00
50.00
60.00
50.00
60.00
50.00
480i (525i)@60Hz
480p (525p)@60Hz
576i (625i)@50Hz
576p (625p)@50Hz
720p (750p)@60Hz
720p (750p)@50Hz
1080i (1125i)@60Hz
1080i (1125i)@50Hz
■ List of supported signals (Video, S-Video signals)
Video mode
NTSC
PAL
SECAM
PAL-M
PAL-N
PAL-60
NTSC4.43
fh(kHz)
15.73
15.63
15.63
15.73
15.63
15.73
15.73
fv(Hz)
60
50
50
60
50
60
60
fsc(MHz)
3.58
4.43
4.25 or 4.41
3.58
3.58
4.43
4.43
■ Pin assignment of COMPUTER IN & MONITOR terminals
11
15
6
10
Pin
No.
1
Pin description
During Y/PB/PR input
During RGB input
Video signal (R)
Video signal (G)
Video signal (B)
N.C
Color difference signal (PR)
2
Luminance signal (Y)
3
Color difference signal (PB)
1
5
4
∗
5
GND
∗
6
GND (R)
GND (PR)
Mini D sub 15 Pin connector
7
GND (G)
GND (Y)
8
GND (B)
GND (PB)
Input Signal
• RGB input
RGB signals:
Horizontal sync signal: TTL level (Pos/neg polarity)
Vertical sync signal: TTL level (Pos/neg polarity)
• Y/PB/PR input
Y signal:
PB/PR signals:
9
+5V
∗
∗
∗
∗
∗
∗
∗
10
11
12
13
14
15
GND
0.7V (p-p) 75 Ω
N.C
SDA
Horizontal sync signal
Vertical sync signal
SCL
1.0V (p-p) 75 Ω
0.7V (p-p) 75 Ω
∗ Do not connect anything.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
■ CONTROL terminal
● Pin assignment
Pin No.
Signal Name
N.C
Description
1
2
3
4
5
6
7
8
9
∗
TXD
RXD
N.C
GND
N.C
N.C
N.C
N.C
Sending data
Receiving data
9
6
∗
Signal ground
∗
∗
∗
∗
5
1
D-Sub 9 pin connector
∗ Do not connect anything.
Notes
• Contact your dealer for control cable and commands.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
TDP-XP1
DATA PROJECTOR
OWNER’S MANUAL
In the spaces provided below, record the Model and Serial No. located at the bottom of
your projector.
Model No.
Serial No.
Retain this information for future reference.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|