Toshiba Projector TDP TW90A User Manual

OWNER’S MANUAL

DATA PROJECTOR

TDP-TW90A

(XGA / With PC Card Slot)

Download from Www.Somanuals.com. All Manuals Search And Download.

Before Using

SAFETY PRECAUTIONS

IMPORTANT SAFETY INSTRUCTIONS

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended

to alert the user to the presence of uninsulated "dangerous voltage" within the product's

enclosure that may be of sufficient magnitude to constitute a risk of electric shock to

persons.

CAUTION: PLEASE READ AND OBSERVE ALL WARNINGS AND

INSTRUCTIONS GIVEN IN THIS OWNER'S MANUAL AND THOSE

MARKED ON THE UNIT. RETAIN THIS BOOKLET FOR FUTURE

REFERENCE.

The exclamation point within an equilateral triangle is intended to alert the user to the

presence of important operating and maintenance (servicing) instructions in the

literature accompanying the appliance.

This unit is fully transistorized and does not contain any parts that can be repaired by the

user.

DO NOT REMOVE THE CABINET COVER, OR YOU MAY BE EXPOSED TO

DANGEROUS VOLTAGE. REFER SERVICING TO QUALIFIED SERVICE

PERSONNEL ONLY.

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE

THIS APPLIANCE TO RAIN OR MOISTURE. DANGEROUS HIGH VOLTAGES

ARE PRESENT INSIDE THE ENCLOSURE. DO NOT OPEN THE CABINET.

REFER SERVICING TO QUALIFIED PERSONNEL ONLY.

1. Read Owner's Manual

3. Source of Light

WARNING: Handling the cord on this product or cords associated with accessories sold with

After unpacking this product, read

the owner's manual carefully, and

follow all the operating and other

instructions.

Do not look into the lens while the

lamp is on. The strong light from

the lamp may cause damage to

your eyes or sight.

this product, will expose you to lead, a chemical known to the State of California

USA only

to cause birth defects or other reproductive harm. Wash hands after handling.

WARNING: This [product] contains mercury. Disposal of mercury may be regulated due to

environmental considerations. For disposal or recycling information, please

contact your local authorities or the Electronic Industries Alliance:www.eiae.org.

USA only

FCC Radio Frequency Interference Statement

Note:

This equipment has been tested and found to comply with the limits for a Class

A digital device, pursuant to part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful interference when the equipment

is operated in a commercial environment. This equipment generates, uses, and

can radiates radio frequency energy and, if not installed and used in accordance

with the instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential area is likely to

cause harmful interference in which case the user will be required to correct the

interference at his own expense.

USA only

2. Power Sources

4. Ventilation

This product should be operated

only from the type of power source

which does not exceed the voltage

range specified on the

rating label and the power cord.

If you are not sure of the type of

power supply to your home,

consult your product dealer or

local power company.

Openings in the cabinet are

provided for ventilation and to

ensure reliable operation of the

product and to protect it from

overheating, and these openings

must not be blocked or covered.

The openings should never be

blocked by placing the product on

a bed, sofa, rug or other similar

surface. This product should not

be placed in a built-in installation

such as a bookcase or rack unless

proper ventilation is provided.

WARNING: Changes or modifications made to this equipment, not expressly approved by

Toshiba, or parties authorized byToshiba, could void the user’s authority to operate

the equipment.

USA only

Notice:

CANADA only

This Class A digital apparatus complies with Canadian ICES-003. Cet appareil

numérique de la classe A est conforme à la norme NMB-003 du Canada.

WARNING: This is a Class A product. In a domestic environment this product may cause

radio interference in which case the user may be required to take adequate

measures.

Download from Www.Somanuals.com. All Manuals Search And Download.

IMPORTANT SAFETY INSTRUCTIONS (Continued)

5. Heat

8. Power-Cord Protection

10. Lightning storms

12. Do not place the product

vertically

The product should be situated

Power-supply cords should be

routed so that they are not likely to

be walked on or pinched by items

placed upon or against them,

paying particular attention to cords

at plugs, convenience receptacles,

and the point where they exit from

the product.

For added protection for this

product during storm, or when it is

left unattended and unused for

long periods of time, unplug it from

the wall outlet. This will prevent

damage to the product due to

lightning and power-line surges.

However, while it is thundering or

lightning, do not touch the

away from heat sources such as

radiators, heat registers, stoves, or

other products (including

Do not use the product in the

upright position to project the

pictures at the ceiling, or any other

vertical positions. It may fall down

and dangerous.

amplifiers) that produce heat.

apparatus and any connected

cable and/or equipment.

This will prevent you from

receiving the electric shock by an

electric surge.

6. Water and Moisture

Do not use this product near water.

- for example, near a bath tub,

wash bowl, kitchen sink, or laundry

tub; in a wet basement; or near a

swimming pool and the like.

13. Stack Inhibited

9. Overloading

Do not stack other equipment on

this product or do not place this

product on the other equipment.

Top and bottom plates of this

product develops heat and may

give some undesirable damage to

other unit.

Do not overload wall outlets; to

reduce the risk of electric shock,

do not use the polarized plug with

an extension cord , receptacle, or

other outlet unless the blades can

be inserted completely with three-

wire grounding type to prevent

blade exposure. As this can result

in a risk of fire or electric shock.

11. Object and Liquid Entry

Never push objects of any kind

into this product through openings

as they may touch dangerous

voltage points or short-out parts

that could result in a fire or electric

shock. Never spill liquid of any

kind on the product.

7. Cleaning

Unplug this product from the wall

outlet before cleaning. Do not use

liquid cleaners or aerosol cleaners.

Use a soft cloth for cleaning.

14. Attachments

Do not use attachments not

recommended by the product

manufacturer as they may cause

hazards.

Download from Www.Somanuals.com. All Manuals Search And Download.

IMPORTANT SAFETY INSTRUCTIONS (Continued)

f) When the product exhibits a

distinct change in performance -

this indicates a need for service.

15. Accessories

20. Safety Check

24. When using a wireless

LAN PC card:

Do not place this product on an

unstable cart, stand, tripod,

Upon completion of any service or

repairs to this product, ask the

service technician to perform

safety checks to determine that

the product is in proper operating

condition.

•Do not use near people

with heart pacemakers

•Do not use near electronic

medical equipment, or in

hospitals or other medical

institutions

•Do not use inside aircraft

or in places where the

wireless LAN card could

interfere with

bracket, or table. The product may

fall, causing serious injury to a

child or adult, and serious damage

to the product. A product and cart

combination should be moved with

care. Quick stops, excessive

force, and uneven surfaces may

cause the product and cart

17. If glass components,

including lens and lamp,

should break, contact your

dealer for repair service.

This product incorporates glass

components, including a lens and a

lamp. If such parts should break,

please handle with care to avoid

injury and contact your dealer for

repair service. The broken pieces

of glass may cause to injury. In the

unlikely event of the lamp rupturing,

thoroughly clean the area around

the projector and discard any edible

items placed in that area.

combination to overturn.

electromagnetic signals.

The electromagnetic interference

could cause a malfunction,

resulting in an accident.

21. Do not leave thermal-paper

documents or easily

deformed items on top of

the unit or near the air

exhaust for long periods of

time.

S3125A

16. Damage Requiring Service

25. If the use of a wireless

LAN PC card interferes

with another device’s

Unplug this product from the wall

outlet and refer servicing to

qualified service personnel under

the following conditions:

18. Servicing

The heat from the unit could erase

the information on the thermal

paper, or cause deformation or

warping.

Do not attempt to service this

product yourself as opening or

removing covers may expose you

to dangerous voltage or other

hazards. Refer all servicing to

qualified service personnel.

electromagnetic signals,

cease use immediately.

The electromagnetic interference

could cause a malfunction,

resulting in an accident.

a) When the power-supply cord or

plug is damaged.

b) If liquid has been spilled, or

objects have fallen into the

product.

c) If the product has been exposed to

rain or water.

22. Do not use the product in

a closed installation state.

Do not place the product in a box

or in any other closed installation

state. Otherwise it may overheat.

This could result in a risk of fire.

26. Do not carry the projector

by having the terminal

cover parts or the PC card

cover part

d) If the product does not operate

normally by following the operating

instructions. Adjust only those

controls that are covered by the

operating instructions as an

improper adjustment of other

controls may result in damage and

will often require extensive work by

a qualified technician to restore

the product to its normal

23. Do not look into the laser

light source of the remote

control or direct the laser

pointer toward a person or

a mirror.

Doing so, the projector may fall if

that cover comes off, and injury or

damage may result.

19. Replacement Parts

When replacement parts are

required, be sure the service

technician has used replacement

parts specified by the manufacturer

or have the same characteristics as

the original part.

Unauthorized substitutions may

result in fire, electric shock, or other

hazards.

The laser beam may cause

damage to the eyes or sight.

operation.

e) If the product has been dropped or

damaged in any way (If the cabinet

should break, please handle with

care to avoid injury) .

(Replacement of the lamp only

should be made by users.)

Download from Www.Somanuals.com. All Manuals Search And Download.

IMPORTANT PRECAUTIONS (Continued)

Avoid Volatile Liquid

POWER SUPPLY CORD SELECTION

If your line voltage is 220 to 240V, use one of the following types of cable.

Do not use volatile liquids, such as an insect spray, near the unit. Do not leave rubber or

plastic products touching the unit for a long time. They will leave marks on the finish.

If cleaning with a chemically saturated cloth, be sure to follow the product's precautions.

Plug

configuration Plug type

Line voltage

220 – 240V

configuration Plug type

Line voltage

200 – 240V

Australian

240V

10A

EURO

Wireless LAN PC Card

• Do not connect the supplied wireless LAN PC card to devices other than this unit. Doing

so could cause malfunction.

Switzerland 200 – 240V

240V

220 – 240V

• To protect the PC card from static electricity, touch some nearby metal, such as a

doorknob or aluminum window frame, before touching the PC card, to rid your body of

static electricity.

• This PC card is a radio product. Concerning the regulations applied in each country/area,

please refer to “Information to the user” supplied.

Use a 5A fuse which is approved by ASTA

or BSI to BSI362.

Always replace the fuse cover after

changing the fuse.

North American 200 – 240V

240V

15A

EXEMPTION CLAUSES

IMPORTANT PRECAUTIONS

• Toshiba Corporation bears no responsibility in the case of damages arising from natural

disaster such as earthquakes, lightning, etc., fire not liable to Toshiba Corporation, acts

by third parties, other accidents, or use under abnormal conditions including erroneous or

improper operation and other problems.

• Toshiba Corporation bears no responsibility for incidental damages (lost profit, work

interruption, corruption or loss of the memory contents, etc.) arising from the use of or the

inability to use this unit.

• Toshiba Corporation accepts no liability whatsoever for any damages arising from not

having followed the descriptions in this Instruction Manual.

• Toshiba Corporation accepts no liability whatsoever for any damages arising from

malfunctions arising from combination with equipment or software that is not related to

Toshiba Corporation.

Save Original Packing Materials

The original shipping carton and packing materials will come in handy if you ever have to

ship your projector. For maximum protection, repack the set as it was originally packed at

the factory.

Moisture Condensation

Never operate this unit immediately after moving it from a cold location to a warm location.

When the unit is exposed to such a change in temperature, moisture may condense on

the lens and the crucial internal parts. To prevent the unit from possible damage, do not

use the unit for at least 2 hours when there is an extreme or sudden change in tempera-

ture

• Toshiba bears no responsibility for information being intercepted or leaked due to the use

of a wireless LAN, or any damages therefore.

Place and Manner of Installation

• Do not place in hot locations, such as near heating equipment. Doing so could cause

malfunction, and shorten the life of the projector.

• Avoid locations with oil or cigarette smoke. Doing so will dirty the optical parts,

shortening their lives, and darkening the screen.

• Do not use this product in the upright position or tilt it up or down by more than 20° from

level. Doing so may cause a failure or shorten the life of the product.

• Using this instrument near a TV or radio may cause interference to the images or audio

sound. If this happens, move it away from the TV or radio.

• Moving the projector from a low-temperature room to a high-temperature room may

cause condensation on the lens or internal parts in the instrument. If you continue to use

it in that situation, the malfunction may result. Ensure to wait until the condensation

naturally disappears.

In the spaces provided below, record the Model and Serial No. located at the bottom of your

projector.

Model No.

Serial No.

• In a high altitude location where air is thin, cooling efficiency is reduced so use the

Retain this information for future reference.

p.32

projector with [Fan mode] set to [High].

Download from Www.Somanuals.com. All Manuals Search And Download.

OTHER CAUTIONS AND INFORMATIONS

REMOTE CONTROL BATTERIES

Copyrights

Caution

Showing or transmitting commercial imaging software or broadcast or cable-broad

casting programs with the purpose of other than the personal and private viewing,

including modifying images using the freeze or resize functions, or displaying with the

varying aspect ratio of the images, could violate the direct or indirect copyrights of the

imaging software or broadcast program, etc., if done without first consulting with the

one of the actions listed above, including obtaining a license from the copyright holder.

• Never throw batteries into a fire.

Using the batteries improperly may cause them to explode or leak and lead to burn or injury. If

battery-leaking fluid contacts skin, wash the fluid off immediately with clean water and consult a

doctor. If the fluid is spilt on an instrument, avoid contact and wipe it off using tissue paper.

(Dispose of the used tissue paper as flammable garbage after moistening with water.)

Notes

• Be sure to use AAA (LR03) size batteries.

• Dispose of batteries in a designated disposal area.

Disposal

• Attention should be drawn to the environmental aspects of battery disposal.

• Do not mix different battery types or combine used batteries with new ones.

• If the remote control does not operate correctly, or if the operating range becomes

reduced, replace both batteries with new ones.

• If the batteries are dead or if you will not be using the remote control for a long time,

remove the batteries to prevent battery acid from leaking into the battery compartment.

This product contains substances which are harmful to humans and the environment.

• The lamp contains mercury.

Please dispose of this product or used lamps in accordance with local regulations.

Following information is only for EU-member states:

The use of the symbol indicates that this product may not be treated as

household waste. By ensuring this product is disposed of correctly, you will

help prevent potential negative consequences for the environment and

human health, which could otherwise be caused by inappropriate waste

handling of this product. For more detailed information about recycling of this

product, please contact your local city office, your household waste disposal

service or the shop where you purchased the product.

Trademarks

• VGA, SVGA, XGA, SXGA, UXGA are trademarks or registered trademarks of

International Business Machines Corporation.

• Digital Light Processing, Digital Micromirror Device and DMD are trademakes of Texas

Instruments.

• Macintosh is a registered trademark of Apple Computer, Inc.

•

Windows is a registered trademark of Microsoft Corporation in the U.S. and other countries.

• Adobe is a registered trademark and Acrobat Reader is a trademark of Adobe Systems

Incorporated.

Notational Conventions Used in This Manual

• References to pages with related information are annotated as follows.

p.36

For example, if making a reference to page 36:

• The illustrations in this document are for reference purposes only and may not reflect

your package exactly.

Download from Www.Somanuals.com. All Manuals Search And Download.

CONTENTS

Automatic demonstration ................................................................................ 45

Playing a slide show from a thumbnail list ...................................................... 46

Checking the projector status ............................................................................ 48

Status display ................................................................................................. 48

Installing the applications................................................................................... 49

Using the Wireless Utility ................................................................................... 50

Displaying a computer’s screen via the projector ........................................... 50

Displaying a JPEG image saved on a computer via the projector.................. 52

Operating the projector................................................................................... 53

Document camera function ............................................................................ 54

How to use the JPEG Conversion Tool .............................................................. 55

Launching the JPEG Conversion Tool ............................................................ 55

Converting an image file................................................................................. 55

Converting files created with Microsoft^®PowerPoint^®..................................... 56

Making a presentation with converted JPEG files .......................................... 57

Creating a screen capture and converting it into a JPEG file ......................... 57

Setting up the projector using a Web browser ................................................... 58

How to use the “Projector Configuration Tool” ................................................ 58

Before Using

SAFETY PRECAUTIONS ..................................................................................

IMPORTANT SAFETY INSTRUCTIONS ...........................................................

POWER SUPPLY CORD SELECTION..............................................................

IMPORTANT PRECAUTIONS ...........................................................................

EXEMPTION CLAUSES ....................................................................................

OTHER CAUTIONS AND INFORMATIONS ...................................................... 10

REMOTE CONTROL BATTERIES .................................................................... 11

CONTENTS ....................................................................................................... 12

Preparations

Checking the package contents ......................................................................... 14

Names of each part on the main unit................................................................. 15

Names of each part on the control panel and remote control............................ 16

Parts on the rear panel ...................................................................................... 17

Preparing and using the remote control............................................................. 18

Placement .......................................................................................................... 19

Connection......................................................................................................... 20

How to use the PC card slot .............................................................................. 21

Maintenance

About lamp......................................................................................................... 62

Lamp replacement ............................................................................................. 62

Lens and main unit cleaning .............................................................................. 64

Operations

Turning the power on and off ............................................................................. 22

Basic operations ................................................................................................ 24

Using handy features ......................................................................................... 26

Using auto setting........................................................................................... 26

Cutting off the picture and sound temporarily (Mute) ..................................... 28

Freezing the image (Freeze) .......................................................................... 28

Using the menus ................................................................................................ 29

How to use the menus .................................................................................... 29

The image adjustment menu .......................................................................... 30

The display setting menu................................................................................ 31

The default setting menu ................................................................................ 32

Displaying Information (Status display) .......................................................... 33

Setting up the wireless LAN............................................................................... 34

Functions ........................................................................................................ 34

Communication mode .................................................................................... 34

Caution when using the wireless LAN functions ............................................ 35

Setup using the Wireless/Card menu ............................................................. 36

How to enter characters ................................................................................. 37

Setting up the network.................................................................................... 38

Computer settings .......................................................................................... 41

Projecting images stored in a memory PC card ................................................ 42

Memory PC cards........................................................................................... 42

JPEG files....................................................................................................... 43

Setting slideshow options ............................................................................... 43

Others

Trouble indications ............................................................................................. 65

Before calling service personnel ........................................................................ 66

Specifications..................................................................................................... 68

List of general specifications .......................................................................... 68

Separately sold product.................................................................................. 68

List of supported signals (RGB signals) ......................................................... 69

List of supported signals (Y/PB/PR signals) .................................................... 70

List of supported signals (Video, S-Video signals) ......................................... 70

Pin assignment of COMPUTER-1/2 & MONITOR terminals .......................... 70

CONTROL terminal ........................................................................................ 71

Download from Www.Somanuals.com. All Manuals Search And Download.

Preparations

Names of each part on the main unit

Checking the package contents

Please make sure that the following items are included in the box, along with the main unit. If

any item is missing, please contact the store immediately where you purchased the product.

(7) (6)

(5)

(4)

(3) (2)(1)

(1)

(2)

(5)

(6)

(8)

(9)

(7)

(8)

(9) (10) (11)

Back

(12)(9) (13) (14)

Front

(3)

(4)

Name

: Function

■ (1) Remote control

■ (2) R6 (SIZE AA) batteries for remote

control (2)

■ (8) Wireless LAN PC card

• “About the Wireless LAN PC Card”

■ (9) Mouse remote control set

• Mouse remote control

p.25

(1) Foot adjuster release button : Press to stow the foot adjuster.

(2) Infrared remote sensor

(3) Lens

(4) Air intake

(5) Speaker

(6) Control panel

(7) Zooming lever

(8) Air exhaust

(9) Tilt adjuster

10) PC card slot section

11) Rear panel

12) Focusing ring

13) Foot adjuster

14) Lamp cover

p.18

: Senses commands from the remote control.

: Projects expanded image.

: Draws in air from outside the projector.

: Outputs audio sound.

: Operates the projector.

: Adjusts screen size.

: Expels air that has grown hot inside the projector.

: Adjusts the projector’s horizontal tilt.

: Mounts/removes the PC card.

: Connects external devices.

: Adjusts screen focus.

: Adjusts the vertical projection angle.

: Remove to replace lamp.

■ (3) CD-ROM

■ (4) Owner’s Manual

■ (5) Power cord ^{(See note)}

■ (6) RGB cable (3m)

■ (7) Carrying bag

• R03 (SIZE AAA) batteries for

mouse remote control (2)

• Mouse remote control receiver

• Mouse remote control manual

p.16

p.25

Note

p.25

The shape and number of supplied power cords vary depending on the product destination.

p.21

(

p.17

p.25

◆The Supplied CD-ROM

p.25

The supplied CD-ROM contains the owner’s manual including information not available for

p.63

its simplified hardcopy, Owner’s Manual (Getting Started), Acrobat^®Reader™ to view the

p.49

manual, and application software

to use the functions of the wireless LAN/PC card.

■ Installing Acrobat^®Reader™

Windows^®: Run the CD-ROM, select the Reader/English folder, and run ar500enu.exe.

Follow the on-screen instructions.

Macintosh: Run the CD-ROM, select the Reader/English folder, and run Reader

Installer. Follow the on-screen instructions to install the software.

■ Viewing the manual

Run the CD-ROM and double-click on Start.pdf. Acrobat^®Reader™ launches, and the

menu screen of the Owner’s manual appears. Click on your language. The Owner’s

Manual cover and list of bookmarks appear. Click on a bookmark title to view that

section of the manual. Click on

to view a reference page with related information.

See the Help menu for more information about Acrobat^®Reader™.

Download from Www.Somanuals.com. All Manuals Search And Download.

Names of each part on the control panel and remote control

Parts on the rear panel

Control panel

Remote Control

(1) (2)(3)(4)(5)(6) (7)

(8)

Remote control

transmitter

(9) (10) (11)

(9)

(1)

(2)

(8)

(10)

(4)

(6)

(3)

(2)

(7)

(6)

(14)

(3)

(4)

(5)

(20)

(19)(18) (17)(16) (15) (14) (13)(12)(11)

: Main Function

(8)

(12)

(13)

(7)

Name

p.18

: Senses commands from the remote control.

: When operating the projector via a computer, connect

(1) Infrared remote sensor

(2) CONTROL terminal

p.71

this to the controlling computer’s RS-232C port.

(1)

p.21

(3) CARD indicator

(4) UNMOUNT button

(5) RESET switch (inside depression) : Press if CARD indicator turns red.

: Displays PC card’s status.

p.21

: Press before removing PC card.

p.21

(6) Eject button

(7) PC card slot

: Press to remove PC card.

: Insert PC cards here.

p.21

(8) AUDIO OUT terminal

(9) MONITOR terminal

: Outputs audio signals.

: Connect to a computer display, etc.

Name

: Main Function

(1) ENTER button

(2) MENU button

(3) SET UP button

(4) ON/STANDBY button

(5) ON indicator

(6) INPUT button

(7) RETURN button

(8) Selection button

(9) LAMP indicator

10) TEMP indicator

11) FAN indicator

12) FREEZE button

13) MUTE button

14) Numeric keypad

: Accepts the selected mode.

: Displays menus.

: Sets up image and mode.

: Turns the power on/off (standby).

: Displays whether power is on or off.

: Selects input.

: Goes back one screen.

: Menu selections and adjustments,etc.

: Displays lamp mode.

: Lights when internal temperature is too high.

: Displays cooling fan mode.

: Pauses image.

: Cuts off the picture and sound temporarily.

(

10) COMPUTER 2 terminal

Input RGB signal from a computer or other source, or a

component video signal (Y/PB/PR) from video equipment.

p.29

(

11) Main power switch

12) AC IN socket

13) AUDIO IN terminal

: AC power line ON (standby)/OFF.

: Connect the supplied power cord here.

p.26

p.22

Input audio signals from a computer or video equipment

with a component video signal output terminal.

Input RGB signal from a computer or other source, or a

component video signal (Y/PB/PR) from video equipment.

p.22

p.24

(

14) COMPUTER 1 terminal

p.30

(

15) S-VIDEO terminal

16) AUDIO (L/R) terminal

17) VIDEO terminal

18) AUDIO (L/R) terminal

19) USB terminal

: Input S video signals from video equipment.

: Input audio signals from video equipment.

: Input video signals from video equipment.

: Input audio signals from video equipment.

: Provided for servicing purposes only. Do not use for

any connection.

p.23

p.65

(

p.65

p.28

(

20) Antitheft lock hole

: Attach a safety cable or any other antitheft device.

: Use to set up the wireless LAN. Numbers and charac-

p.37

ters can be entered.

Note

• Although this owner’s manual abbreviates component video signals as Y/PB/PR, the

product also supports signals from video equipment marked “Y/C^B/CR.”

Notes

• For the remainder of this manual, buttons are referred to as follows:

Selection buttons ⇒ ; ENTER button ⇒

• For further information of the mouse remote control, see the Owner’s Manual of the

Mouse Remote Control.

Download from Www.Somanuals.com. All Manuals Search And Download.

Preparing and using the remote control

Placement

■ Loading dry-cell batteries

into the remote control

q Remove the battery cover.

■ Operating the remote

Placement Styles

As shown in the figures below, this device can be placed in 4 different styles.

control

The factory setting is “floor-mounted front projection.” Set the Projection mode in the

Point the remote control toward the

projector’s infrared remote sensor,

and press a button on the remote

control.

p.32

default setting menu

, in accordance with your needs.

Floor-mounted front projection

Floor-mounted rear projection

• Operating the projector from the front

w Insert the dry-cell batteries.

Ceiling-mounted front projection

Ceiling-mounted rear projection

Be sure to align the plus and minus

ends of the batteries properly.

Approx. 15°

Approx. 5m

WARNING

Two batteries (R6, SIZE AA) are used.

• Always obey the instructions listed in IMPORTANT SAFETY INSTRUCTIONS when placing the unit.

Attempting to clean/replace the lamp at a high site by yourself may cause you to drop down, thus

resulting in injury.

• Operating the projector from the rear

e Replace the battery cover.

• If you wish to mount the projector on the ceiling, be sure to ask your dealer to do so. Mounting the

projector on a ceiling requires special ceiling brackets (sold separately) and specialized knowledge.

Improper mounting could cause the projector to fall, resulting in an accident.

• If the projector is ceiling-mounted, install the breaker for turning off the power in case of anomaly. Let

everyone involved with the use of the projector know that fact.

(1)

(2)

Approx. 15°

Approx. 5m

Projection Distance and Size

Use the figures, tables, and formulas below to determine the projection size and projection distance.

(Projection sizes are approximate values for full-size picture with no keystone adjustment.)

Screen

As seen from above

Dry-cell batteries

• Before using the batteries, be sure to observe the Safety Precautions described in

previous pages.

• Remove batteries from remote control when not using for extended periods.

• If the remote control stops working, or if its range decreases, replace all the batteries with

new ones.

a (min length) = projection size (inches) × 0.04064

a (max length) = projection size (inches) × 0.04878

projection distance a (m)

projection

size (inches)

height (H)

(cm)

The remote control

• The remote control may fail to operate if the infrared remote sensor is exposed to bright

sunlight or fluorescent lighting.

• Do not drop or bang.

• Do not leave in hot or humid locations.

• Do not get wet or place on top of wet objects.

• Do not take apart.

• In rare cases, ambient conditions could impede the operation of the remote control. If this

happens, point the remote control at the main unit again, and repeat the operation.

• For further information of the mouse remote control, see the Owner’s Manual of the

Mouse Remote Control.

As seen from the side

min length

max length

(zooming max) (zooming min)

Lens center

30.75

—

1.50

1.95

2.93

3.90

4.88

7.32

9.76

—

15.46

20.12

30.18

40.23

50.29

75.44

100.58

123.72

1.63

2.44

3.25

4.07

6.10

8.13

10.00

100

150

200

246

a is the distance (m) between the lens and the

screen, and corresponds to a range of 1.50 m to

10.00 m. H is the height from the image bottom to

the center of the lens.

Download from Www.Somanuals.com. All Manuals Search And Download.

Connection

How to use the PC card slot

The wireless LAN PC card enables you to connect the projector wirelessly with a personal

Before connection

• Read the owner’s manual of the device you are connecting to the projector.

• Some types of computer cannot be used or connected to this projector.

Check for an RGB output terminal, supported signal

• Turn off the power of both devices before connecting.

p.34

computer that supports IEEE802.11g/b based wireless LAN.

(Please note that

communication between all the computers based on IEEE802.11g/b and this projector is

not guaranteed.) You can also use a commercially available memory card to project JPEG

image files using this projector. ^p.42Please follow the steps below when removing or

mounting a PC card.

p.69

, etc.

• The figure below is a sample connection. This does not mean that all of these devices

can or must be connected simultaneously. (Dotted lines mean items can be exchanged.)

■ Mounting a PC card

■ Removing a PC card

q Insert the PC card.

q Look at CARD indicator.

Audio amplifier, etc.

After making sure of the card orienta-

If it is off, proceed to step r.

Computer (for control)

tion, press it in firmly until it stops.

CARD indicator

Video recorder,

DVD player, etc.

UNMOUNT button

VCR

To audio output

White (L)/Red (R)

To video

output

To audio output

White (L)/Red (R)

Video cable

(not supplied)

To S-Video

output

To audio input

White (L)/Red (R)

RS-232C

terminal

p.71

Control cable

w Press the UNMOUNT button.

Audio cable (not supplied)

S-Video cable

(not supplied)

AV cable

(not supplied)

Begins processing for PC card removal.

PC Card

e Wait until CARD indicator goes

out.

When the PC card is detected correctly,

the CARD indicator comes on in green.

Never remove the PC card while lit.

Doing so could damage the PC card or

corrupt your data.

r Press the Eject button.

Eject button

Audio cable

(not supplied)

RGB cable

(supplied)

RGB cable

(not supplied)

Audio cable

(not supplied)

Monitor cable Mini

D-sub 15P-BNC

(not supplied)

To RGB

output

To RGB

output

To audio output

The Eject button is a bit stiff, so

press firmly while supporting the

projector. Be careful to avoid injury

when doing so.

To audio

output

To Y/CB/CR output

Green (Y)/Blue (C^B)/Red (CR)

Conversion adapter BNC-pin

(not supplied)

Computer

DVD video recorder, etc.

Computer

■ If CARD indicator turns red

CARD indicator

RESET switch

Press the RESET switch with a thin pin

or similar implement (it is at the bottom

of a recess).

Notes

• COMPUTER terminals 1 and 2 function identically.

• The AUDIO IN terminal doubles for devices connected to COMPUTER terminals 1 and 2.

Download from Www.Somanuals.com. All Manuals Search And Download.

Operations

Turning the power on and off

Notes

■ Connecting the power cord

• The start-up screen will disappear after a moment.You can dismiss the start-up screen

before this by performing any operation.You can also configure the start-up screen not to

Insert the power cord connector into the

AC IN socket of the projector.

p.31

appear via the Display setting menu

• The first time you use the projector after purchase, after the start-up screen disappears,

Insert the power cord plug into a wall or

other power outlet.

p.24

the Language menu is displayed

Power cord connector

(Supplied)

■ Turning the power off

■ Removing the lens cover

Be sure to remove the lens cover when the power is

turned on. If it is left on, it could become deformed due

to heat.

Press the ON/STANDBY button.

A message appears on the screen, confirming that you wish to shut off the power. This

message will disappear after a moment. (This operation is no longer valid after the

message disappears.)

Press the ON/STANDBY button again.

The screen turns off, but the internal cooling fan continues to operate for a short while.

Then, the projector goes into standby mode.

■ Turning the power on

When cooling lamp

During internal cooling

After cooling complete

Turn on the main power

switch.

The ON indicator will change to

(Green)

Flashing

(Green)

(Off)

(Green)

(Off)

(Orange)

orange, indicating standby mode.

During cooling, the LAMP indicator flashes. In this state, the power cannot be

turned back on.

Remote

Control

Press the ON/STANDBY

button.

Control panel

After the LAMP indicator goes off, the cooling fan continues to operate for a

short while, in order to expel excess internal heat. If you are in a hurry, there is

no problem with unplugging the power cord or turning off the main power switch

in this state.

Start-up screen

The power turns on, and the following

3 green indicators light: ON, LAMP,

and FAN. After a moment, the start-up

screen appears.

In standby mode

Note

• The projector consumes about 18W of power in standby. We recommend that you unplug

the power cord or turn off the main power switch if you will not be using the projector for

an extended period.

CAUTION

• Do not look into the lens while the lamp is on. The strong light from the lamp may cause

damage to your eyes or sight.

PRECAUTION

• Do not block the air intake or exhaust. Doing so could cause a fire due to internal overheating.

• Do not place your hands, face, or other objects near the air exhaust. Doing so could cause

burns, deform/break the object.

• If the power cord is unplugged before cooling is complete, give the lamp time (about 5

minutes) to cool before plugging it back in. If the lamp overheats, it may fail to light.

Download from Www.Somanuals.com. All Manuals Search And Download.

Basic operations

Turn on the power.

Turn on the power by following the instructions in “Turning the power on”

Projector placement angle adjustments

The placement angle and the height of the projected image can be adjusted by the foot

p.22

adjuster.

Select the language and the lamp power (When using the

first time).

When the projector is used for the first time after purchase, menu for language and

lamp power selection and configuration is displayed in English. (If the screen is out of

q Lift up the front of the projector to

the desired angle, then press the

foot adjuster release button.

The foot adjuster extends. Release the

button to lock the position.

focus, adjust it according to the step .)

w To adjust the horizontal angle, use

the tilt adjuster.

q Use the

button to select the

button.

English

French

German

Italian

Spanish

Portuguese

Russian

Swedish

Turkish

Japanese

Chinese (simplified)

Chinese (traditional)

Korean

desired language and press the

Message for setup confirmation is displayed in a

selected language.

Then, the menu for lamp power selection and

configuration is displayed. It is automatically set as

Standard. To change the setting, follow the step w.

To stow the foot adjuster, hold up the

projector while pressing the foot adjuster

release button, then slowly lower the

projector.

Adjusting the screen size and focus

q Use the zooming lever to adjust the screen

w Use the

power and press the

The lamp power, if selected, will be toggled without

pressing the button. The display automatically

button to select the lamp

button.

size.

w Use the focusing ring to adjust the focus.

disappears in a few seconds.

Adjusting the volume with the

The speaker volume can be adjusted when an audio signal is being input.

buttons

Notes

• When the projector is turned on the next time, the Language and Lamp power

menus do not appear upon startup. However, if “Reset all” is executed from the

Notes

p.32

Default setting menu

, the Language and Lamp power menus will be

• Note that lamp characteristics may rarely cause the brightness to fluctuate slightly.

• A lamp is consumable item. If used for extended periods, images will appear dark, and

the lamp could burn out. This is characteristic of a lamp, and is not malfunction. (The

lifetime of the lamp depends on conditions of use.)

displayed the next time when the power is turned on.

• The language can also be set via the Display setting menu

p.31

and Lamp power

p.32

via the Default setting menu

• This owner’s manual assumes that English has been selected.

• The DMD^TMis made using extremely advanced technology, but there may be black spots

(pixels that do not light) or bright spots (pixels that are constantly lit) on the panel. Please

note that these are not malfunctions.

Activate the connected device.

Turn on and start the connected device such as a computer.

p.69

• Although this projector supports a wide range of RGB signals

, any resolutions not

supported by this projector (XGA) will be expanded or shrunk, which will affect image

quality slightly. To view high-quality images, it is recommended that the computer’s

external output should be set to XGA resolution.

Press the INPUT button.

An image of the connected equipment is projected.

• With some models of computer having LCD displays or the like, displaying images

simultaneously on the projector and the monitor’s display may prevent the images from

displaying properly. If this happens, turn off the computer’s LCD display. For information

on how to turn off the LCD display, see the owner’s manual of your computer.

• If a signal not supported by the projector is input, the “Unsupported signal” will appear.

• If no signal is being input from the connected device, the “No signal” will appear.

Each time you press the INPUT button, it switches to the input of the connected

equipment.

Notes

p.32

• When [Auto input search] is set to [On] in the default setting menu

, the image of

the equipment which is connected and turned on is projected.

• If an unavailable operation button is pressed, the

icon will appear.

• Moving pictures generated with the DVD software for computers may appear unnatural if

it is projected with this projector, but it is not a malfunction.

Download from Www.Somanuals.com. All Manuals Search And Download.

Using handy features

● Manual adjustments and settings

■ Using auto setting

Remote

Control

The menu items of the Set up menu vary depending on the input type, as shown in

the table below.

This function sets up the projector to the optimum state for

each type of the input signal by using simple operations.

Control panel

Use the

buttons to adjust the items in the table below, then press

Press the SET UP button.

the RETURN button when you are finished.

The Set up menu appears.

Video

S-video card

Press the SET UP button again.

The menu item is automatically adjusted/set.

Select Item

Description

Computer Y/PB/PR

Auto. Keystone Automatically corrects the keystone distortion.

Press

Yes

For computer input, the

icon will appear during

processing.

Keystone

Correct the keystone (trapezoid) distortion of the

screen.

p.27

For manual adjustment and setting, see the following table

Screen shrinking

downward

Screen shrinking

upward

Note

• The image may not be projected or auto adjustment/setting may not be performed

correctly for input signals other than those supported by the projector

Auto setting Automatically adjusts items such as the sampling

phase depending on the type of input signal.

Press the SET UP button.

Yes

p.69 p.70

●Correcting the keystone distortion

Phase

Adjust with

to eliminate flicker.

Yes

p.25

When the foot adjuster

is used to change the projector placement angle while

Frequency Adjust with

to eliminate periodic patterns

projecting the image, the picture will undergo keystone (trapezoidal) distortion.

and flickering when many vertical lines appear

on the screen.

This projector is capable of correcting this keystone distortion

Before correction After correction

H-position Adjust the horizontal position of the image.

Yes

Move left

V-position Adjust the vertical position of the image.

Move down Move up

Adjusts the clamp pulse position.

Lower Higher

Adjusts the clamp pulse width.

Narrower Wider

Move right

Yes

Clamp 1

Clamp 2

Yes

Press the SET UP button.

Press the

button.

The keystone distortion is automatically corrected. The

correction.

icon appears during this

● Manual adjustment

Press the SET UP button to display the Set up menu and select [Keystone]. Use

the buttons for keystone adjustment. When the adjustment is finished, press

the RETURN button. The menu disappears.

Notes

• Depending on the amount of keystone adjustment and the content of images, some

information may be lost, or the picture quality may suffer.

• Keystone adjustment is available for the keystone distortion in a slant angle of ±15

degrees.

Download from Www.Somanuals.com. All Manuals Search And Download.

Using handy features (Continued)

Using the menus

You can call up on-screen menus, and conduct a number of adjustments and settings using

■ Cutting off the picture and sound temporarily (Mute)

p.16

the operation buttons

on the control panel (main unit side) and remote control.

Remote

Control

When you want to project the images of another projector, overhead

projector, etc. temporarily, this projector’s images and sound can be

turned off.

■ How to use the menus

The menu shown below is for operation instructions purposes and might differ from the

actual display.

Press the remote control’s MUTE button.

The picture and sound are cut off. (The Mute function is released

when pressing the MUTE button again.)

Display the Setting display menu

1. Press the MENU button

2. Select a Category

Notes

Select a category by using

Displays the current

adjustments and settings of

selected category.

• The

icon will appear while mute is in effect.

There are following four

categories:

• Operating any other functions will also cancel the muting.

Item shown with gray cannot

be adjusted with the current

input source.

■ Freezing the image (Freeze)

p.30

Image adjustment menu

Remote

Control

The image being projected can be made to be frozen. This function is to

be used to pause a video during a presentation, etc.

p.31

p.32

p.33

Display setting menu

Default setting menu

Status display menu

Press the remote control’s FREEZE button.

The picture pauses. (The Freeze function is released when pressing

the FREEZE button again.)

3. Adjustments & Settings

Press

to open the menu.

5. Press the MENU button

The Wireless/Card

menu appears.

* Displayed only in wireless/card

input mode.

Notes

Item

Adjustment/Setting Value

• The

icon will appear while freeze is in effect.

• Other operation will also release the freeze.

• Even if an image is frozen on the projector, the pictures are running on the video or

other equipment.

• If you use this function on video software sold on the market, broadcast or

broadcast on cable except for the purpose of your private viewing and listening, it

may infringe the copyright protected by the copyright laws.

To Wireless/Card

These marks signify the

items can be adjusted/set

p.36

This mark signfy that

there are options.

by using

Press

to display a

list of options.

These marks signify the items can

be selected from the list by using

After an item is selected, apply it

by pressing

The figure shows displays given for operation instructions purposes. As the display

may differ depending on the item, use the following pages as a reference.

6. End

Press the MENU button

The menu disappears.

4. Back

Press the RETURN button

Note

• Menu adjustments and settings are saved when the power is turned off via the ON/

STANDBY button. If the power cable is disconnected before this, or the power goes out,

then the data will not be saved.

Download from Www.Somanuals.com. All Manuals Search And Download.

Using the menu (Continued)

■ The display setting menu

Use this menu to set screen display-related items.

■ The image adjustment menu

Use this menu to adjust image-related items.

Items that can be adjusted are marked with “Yes”, and those that cannot are marked with “No”.

Description

Item

Video

S-video

card

Item

Contrast

Description

Computer Y/PB/PR

Screen size

(Full): Display with 1024 × 768 dot resolution

(Thru): Display with sampling resolution (for computer input)

(Wide): Wide-screen display (for Video, S-video, and Y/PB/PR

Adjust the image contrast.

Yes

Lower

Brightness Adjust the brightness of the image.

Darker Brighter

Adjust the color of the image.

Lighter Deeper

Adjust the tint of the image color.

Reddish Greenish

Sharpness Adjust the sharpness of the image.

Softer Sharper

Set the function to reduce screen noise. No

On (Enable) Off (Disable)

Press . Toggle the picture mode with

Higher

)

Yes

Select one of the languages below to use for displaying the menu and messages

Language

[

: Enter setting mode]

[

:Selection]

[Apply:

]

Color

Tint ^*1

English/Français/Deutsch/Italiano/Español/Português/

Svenska/Türkçe/

Background Screen to display when there is no input signal

(Logo)

(Blue)

(Black)

Icon

Display icons as function guides

Off

Yes

Display start-up screen when power is turned on On

Start-up screen

Noise

reduction

Note

Picture

mode

Yes

• If “Thru” is selected for screen size, portions exceeding the native resolution (1024 × 768

pixels) will not appear on the screen. Note that for RGB signals with clock frequency

140MHz or lower, all input pixel signals are sampled. However, if the clock speed is

higher than this, the RGB pixel signal is thinned before sampling.

Bright/Standard/True color

R-level

G-level

B-level

Adjust red of the image color.

Yes

Less red

Adjust green of the image color.

Less green More green

Adjust blue of the image color.

Less blue More blue

NTSC mode^*1Set the black level with

US: NTSC (US) mode

Japan: NTSC (JAPAN) mode

More red

button.

*1: [Tint] and [NTSC mode] can be displayed and adjusted only when the video signal is set to

[NTSC] and [NTSC4.43]. (NTSC mode is set to JAPAN when the language is set to Japanese. It is

set to US for other languages.)

Download from Www.Somanuals.com. All Manuals Search And Download.

Using the menu (Continued)

■ The default setting menu

This menu shows placement status and other settings.

■ Displaying Information (Status display)

This displays information about the input signal, lamp use time, etc.

Description

Item

“Yes”: displayed, “No”: not displayed

p.19

(Rear mounted

from ceiling)

Projection

mode

Sets projection mode in accordance with Placement Style.

Video

S-video

Yes

card

Yes

(Mounted

Item

Description

Computer Y/PB/PR

(Standard)

(Rear)

from ceiling)

Input

Input source name

Yes

No signal

power off

Set the timer to wait for the power to be turned off after signal input stops.

Press . Switch with and

Mode name

H-resolution

V-resolution

H-frequency

V-frequency

Sync

Signal format

Video mode

Lamp time

RGB input mode ^{[Note 1]}

Horizontal resolution (in dots)

Vertical resolution (in dots)

Horizontal sync frequency

Vertical sync frequency ^{[Note 2]}

Sync signal polarity ^{[Note 3]}

Y/PB/PR signal format

Off (not turned off)/1 min./5 min./10 min./30 min./60 min.

Auto input

Set whether the input with signals is only selected or not.

Off

Power on

Sets whether to turn on the power when the ON/STANDBY button is pressed

(Manual), or when the main power switch is turned on (Auto). Manual

Auto

Standard

High

Color method of video signal

Lamp power ^{[Note 1]}

Fan mode ^{[Note 2]}

Reset all

Time of lamp use ^{[Note 4]}

Yes

Sets the lamp power.

Low

Lamp reset count The count for lamp replacement Yes

Total time

Version

Standard

Sets the cooling fan speed.

The total time that this projector is used Yes

Press

Firmware version ^{[Note 5]}

Yes

Resets all adjustments and settings to their factory settings.

Notes

1: The mode of supported RGB signals

Notes

is shown.

p.69

2: Same as the refresh rate of the computer signal.

3: Sync signal polarity shown as P (positive) or N (negative) for [H/V].

1: When Lamp power is set to Low, the screen becomes a little darker, but the cooling fan noise gets

quieter.

2: Setting [Fan mode] to [High] increases the cooling fan speed. Set this option to use the projector,

for example, at high altitude (over 1,500 meters above sea level).

4: Displays [Lamp time] as a measure of when the lamp should be replaced. (Cannot be used as

a counter of guaranteed lamp time.) When the displayed time approaches 2,000 hours, consult

with a store about getting a TLPLW3A replacement lamp (sold separately) prepared.

5: [Version] shows the version of the projector’s internal control program. This version is referred

to for customer service, etc.

Notes

•

Note that in the event of a power outage but the power is restored afterwards, the projector

power will come on if Power on is set to Auto.

• When you turn off the projector even if Power on is set to Auto, you must press the ON/

Note

STANDBY button to turn the power off.

• The displayed information will not be refreshed if the status changes. To refresh the

information, dismiss the display, then display it again.

Download from Www.Somanuals.com. All Manuals Search And Download.

Setting up the wireless LAN

■ Functions

■ Caution when using the wireless LAN functions

The following functions are available via wireless communications, when the wireless LAN

PC card and dedicated Wireless Utility software

Note: A wireless LAN PC card except the supplied one (or recommended by

Toshiba) does not work with this product. Please ask your dealer about the

available wireless LAN PC card.

The Wireless LAN in this unit uses the 2.4 GHz waveband. If there is a similar wireless

LAN in the area, or a wireless device using the 2.4 GHz waveband, or a microwave

oven, the communication efficiency of this apparatus will be reduced, and may become

unusable, but it is not a fault. If this happens, check an area away from the current

location that will not cause radio interference to medical, industrial and public equip-

ment, and change to it, or stop using the unit.

p.50

included with this projector are used.

1) Displaying a computer’s screen via the projector

The computer’s desktop screen can be sent, as well as the screens of a variety of

software applications, to the projector for display.

2) Displaying an image saved on a computer via the projector

JPEG files can be sent to the projector for display.

3) Operating the projector by means of a computer

Some of the same functions available from the remote control can be performed.

■ Communication mode

This projector supports both Ad hoc and Infrastructure Communication modes.

◆ Ad hoc communication mode

This is transmission mode to communicate

between wireless LAN equipment.

Wireless communication can be performed via the

simple configurations. This function can only be

used if the projector is in range of the computer’s

wireless signals.

Toshiba does not guarantee the converage of the radio wave in the form of figures. The

converage varies depending on the performance of each wireless LAN equipment,

existence of obstacles or other wireless LAN equipment used by nearby working

groups, etc. The coverage is generally estimated on the assumption that wireless LAN

equipment be used in an unobstructed office or conference room.

◆ Infrastructure communication mode

This mode allows the projector to communicate

with a wireless-LAN/wired-LAN mixed network via

an access point. (It even allows for communication

To premises

LAN or Internet

between wireless LAN devices.)

Connecting to the rest of the world via a wired LAN

or the Internet generally requires a high level of

security.

Hub

Access point

Use the appropriate transmission mode for your network environment.

Download from Www.Somanuals.com. All Manuals Search And Download.

Setting up the wireless LAN (Continued)

■ Setup using the Wireless/Card menu

● Projector settings (Be sure to read this subsection.)

■ How to enter characters

Use the numeric keypad on the remote control to enter characters. Enter each charac-

ter of interest and press the

button to accept it.

The factory settings can be used as-is. However, if you need higher security, the

projector settings should be changed.

Text input mode

1. Press the MENU button twice

Display the Wireless/Card menu.

Remote

control

buttons

Only-digital input items

(Examples:

Alphanumeric character/symbol input items

(Examples: SSID, Key settings)

* Displayed only in Wireless/Card input mode.

2. Select a Category

TCP/IP settings)

Select a category by using

Displays the current settings

of selected category.

Dimmed items cannot be

changed under the current

settings.

“1” “.”

“2” “A”

“@” “-”

“B” “C”

“_”

“a”

“d”

“g”

“j”

“1”

“2”

The following three categories

are available:

“b”

“e”

“h”

“k”

“c”

“f”

“i”

“3” “D” “E”

“4” “G” “H”

“F”

“I”

“3”

“4”

“5”

“6”

“7”

“8”

“9”

p.38

p.43

p.48

Network setup

Slide Show setup

Status display

“5” “J”

“K”

“L”

“l”

“6” “M” “N” “O” “m” “n”

“o”

“q”

“v”

“x”

“7” “P” “Q” “R” “S”

“p”

“u”

“w”

“r”

“s”

“z”

“8” “T”

“U” “V”

“Y”

“t”

“9” “W” “X”

“Z”

“y”

3. Make settings

Press

to open the menu.

“0” “space "#$%&'()*+,-./:;<=>?@[\]^_`{|}~”

Erase one character.

“0”

These marks signify that

options can be selected by

Erase one character.

using

Item

Setting Value/Option

5. End

Press the MENU

button

The menu disappears.

The figure shows a typical example. As the display

may differ depending on the item, use the following

pages as a reference.

4. Back

Press the RETURN button

Download from Www.Somanuals.com. All Manuals Search And Download.

Setting up the wireless LAN (Continued)

• [SSID]

■ Setting up the network

This is an ID code for connecting to specific individuals over a wireless LAN. This may

also be called “Network group” or “Network name”. Please read the following carefully.

p.36

If you select Network in step 2 in “Projector settings”

, the following items can be set.

Item

Description

Note 1: The SSID is set to TDPJ when shipped from the factory. If you leave this setting

as it is, security may be compromised due to access by a third party using the

“Wireless Utility” within the projector’s possible communication area. Before

using the projector, therefore, be sure to set SSID to a character string different

from the default.

Note 2: When you use the Ad hoc communication mode, if there is a similar SSID

network group (for example TDPJ, TDPJ1, TDPJ2, etc.) in the possible

communication area, it is possible that your projector name will not be dis-

played in the Wireless Utility projector list column. If this is the case, set SSID

to a completely different character string.

Ad hoc

Infrastructure

Mode

Use

to select the number (1 to 11) to be set.

Channel

SSID

Specify an arbitrary character string (1 to 32 characters).

[

: Enter the setting mode]

[

: Move from digit to digit]

[

: Enter the string] [Accept:

]

Encryption

Key

Off

Specify an arbitrary character string.

(A string of 5 or 13 characters or a string of 10 or 26 characters in

hexadecimal notation)

• [Encryption]

Enable or disable encryption for security purposes.

[

: Enter the setting mode]

[

: Move from digit to digit]

: Enter the string] [Accept:

]

Note: Encryption is factory-set to Off. If you use the projector with this setting left

unchanged, security may be compromised due to access by a third party using

the Wireless Utility within the projector’s coverage. Before using the projector,

therefore, be sure to set Encryption to On.

DHCP

Use

Not use

TCP/IP

Enter single-byte numeric characters to specify the IP

address/subnet mask/gateway.

[

Enter the setting mode

]

[

Select an item

]

[

: Move

]

from digit to digit] to : Enter the string] [Accept:

[

]

• [Key]

Setting

initialization

When you have set Encryption to On, the encryption key must be set. For use at an

encryption level of 64-bit, specify a string of 5 arbitrary characters or a string of ten

characters in hexadecimal notation. For use at the 128-bit level, specify a string of 13

arbitrary characters or a string of 26 characters in hexadecimal notation.

Initialize the wireless LAN settings.

: Enter the execution mode] [Yes

[

No] [Accept:

Projector

name

Specify an arbitrary character string (0 to 8 characters).

[

: Enter the setting mode]

[

: Move from digit to digit]

[

: Enter the string] [Accept:

]

Note: Alphabetic characters (A to F, a to f) used in hexadecimal notation are case

insensitive; the uppercase characters and their lowercase equivalents are

handled to be identical.

Other

Remote control/Browser authentication/Password/Status

notification/SMTP server/Destination address

* To enter characters, use the numeric keypad on the remote control.

The higher the number of bits, the stronger the encryption, and hence the harder it will

be for a third party to decipher your communications. However, setting higher encryp-

tion levels may slow down communication speed. To set the highest security level,

specify a 128-bit encryption key. For higher security, avoid using a word found in a

dictionary and change the key sometimes.

Note

• The wireless LAN settings take effect the moment you closes the menu.

● Details on individual items

• [Mode]

Set the following item if you have set the communication mode to Infrastructure.

Your projector is set to Ad hoc in the factory. Change the setting if you want to use the

projector in Infrastructure mode.

• [DHCP]

If you set DHCP to Use, the IP address of the projector is assigned automatically by the

DHCP server. If your network environment does not assign IP addresses automatically,

set DHCP to Not use, then set the following item TCP/IP manually.

• [TCP/IP]

If you have set DHCP to Not use, ask the network administrator to check for the

following items, then perform the TCP/IP settings manually.

• [Channel]

Usually, you do not have to set this item. If a network group having the same SSID

already exists in the projector’s coverage, the channel is changed automatically to the

channel of that network group.

Note 1: If a set channel is in bad connections for wireless connection, try the other

channels to avoid the effects of radio waves to select the one in possibly the

best communication conditions.

Note 2: To communicate in Ad hoc mode with a computer that cannot change the

channel, start up the projector before the computer.

• IP address

An IP address is a unique number assigned to a terminal for connection to the

Internet. The format is a string of four dot-separated three-digit numbers. (Example:

111.112.xxx.xxx)

Download from Www.Somanuals.com. All Manuals Search And Download.

Setting up the wireless LAN (Continued)

• Subnet mask

■ Computer settings

A subnet mask is used to determine what subnet the IP address assigned to a

terminal belongs to. (Example: 255.255.xxx.xxx)

• Gateway

This value specifies the device, such as a router, to be used to access servers outside

the network. It is identified by the IP address. (Example: 111.112.xxx.xxx)

• [Setting initialization]

Refer to instruction manuals of your computer or wireless LAN PC card to perform the

following settings.

• Select Ad hoc (for some PC cards, this is Peer-to-Peer Group).

• Set the Channel to channel assigned to the projector (in factory reset mode, this is set to

10).

This item resets the wireless LAN settings to their factory defaults.

• [Projector name]

This can be used to identify projectors when communicating with multiple projectors, or

if there is a possibility that another person who is out of communication range will be

using the same projector. It is recommended this is set to prevent wrong transmission.

For some computers, you cannot set the channel in Ad hoc mode.

• Set SSID (for some types of PC card, use Network name instead) as the same as

projector’s SSID (at factory shipment, this is set to TDPJ).

• If Encryption and Key are set on the projector, set to the same values.

• [Other]

Note: It is imperative that the projector and computer encryption settings are the same.

If the settings are different, the encryption may be invalid when sending in the Ad

hoc communication mode, so be careful.

This item is expanded into the following items:

Item

Description

Remote

control

Select whether this projector is to be remote-controlled by the

computer.

Allowed

Presentation

Forbidden

Allowed

: Always accepts remote commands from the computer.

Presentation : Accepts remote commands only from the computer,

the screen of which is currently being displayed via

the projector by the Wireless Utility (Update

automatically).

Forbidden

Enable or disable password authentication for access to the setting

menu of the Projector Configuration Tool. On Off

: Always ignores remote commands from the computer.

Browser

authentication

Set the password to be made valid for access to the setting menu

when [Browser authentication] is set to [On]. Specify a string of

arbitrary characters (1 to 8 characters).

Password

[

: Enter the setting mode]

[

: Move from digit to digit]

[

to : Enter the string] [Accept:

]

Select whether to automatically send error information to a specified

e-mail address if an error occurs, for example, when the lamp has

Status

notification

blown. On

Off

Set the IP address of the SMTP server.

SMTP server

[

: Enter the setting mode]

[

: Move from digit to digit]

[

to : Enter the string] [Accept:

]

Set the e-mail address of the recipient of the status notification,

within 60 characters. ([email protected])

Destination

address

[

: Enter the setting mode]

[

: Move from digit to digit]

to : Enter the string] [Accept:

]

PRECAUTIONS

• Browser authentication and Password are factory-set to Off and no string,

respectively.You should set them as soon as possible.

• If you have forgotten your password, set it again using the menu on the main unit.

Download from Www.Somanuals.com. All Manuals Search And Download.

Projecting images stored in a memory PC card

This projector can read JPEG files from a memory PC card to display them on the screen.

This allows you to give presentations without a computer, create an advertising screen

board using the slideshow function, and more. (The projector cannot reproduce animation

effects such as those produced by Microsoft^®PowerPoint^®.)

■ JPEG files

(1) Supported file extensions are jpg, JPG, jpeg, and JPEG.

(2) The maximum number including both folders and files is 512.

(3) Some JPEG files are not supported by this projector.

The limitations in (3) above can be alleviated by converting the JPEG file with the

■ Memory PC cards

● PC card slot types

p.55

supplied JPEG Conversion Tool

software application.

■ Setting slideshow options

The PC card slot installed on this projector is TYPE II (PCMCIA Release 2.1)-compliant.

Please use memory PC cards and conversion adapters compliant with this type of PC

card slot.

Slideshow is the function to display the JPEG image files stored in a memory PC card

one after another at fixed time intervals. When switching from one image to the next,

Slideshow can add various display effects (transitions) to them. If you select Slide

p.36

Only a 3.3-V PC card can be used. (A 5-V only PC card cannot be used.)

Show in step 2 in “Projector settings”

, the following items can be set.

● Supported storage media types

This projector supports the following types of ATA-compliant storage media. This

owner’s manual refers to the combination of the ATA conversion adapter and media in

use as a “memory PC card.”

Item

Description

Manual

Auto. (Select whether to automatically switch to

wireless/card input when a PC card in plugged.)

PC card

display

Storage media that can be used as-is

Off (Select whether to automatically start a slide show

when a PC card in plugged.)

Auto. demo

Flash ATA card, TOSHIBA Mobile Disk

Storage media that can be used in combination with each of the ATA conversion

adapter types

Select the slide show display interval from among the following

Interval

options using

5 sec./10 sec./30 sec./1 min./3 min./5 min./10 min.

SmartMedia™, CompactFlash card, SD memory card, miniSD card, MMC, memory

stick, xD-Picture Card™

Note that inserting conversion adapters and memory cards with different functions than

above, and other memory cards (excluding the supplied wireless LAN PC card) into the

projector could damage the PC card or cause malfunctions.

Select the type of transition for slide shows from among the following

Display effect

Play icon

options using

None / Wipe / Wipe / Wipe / Wipe / Dissolve / Cover

Cover / Cover / Cover / Checker / Zoom / Rotate zoom /

Belt wipe / Blind

● Memory PC Cards Whose Operation Have Been Confirmed

Please note that presence on this list is not a guarantee of operation.

• TOSHIBA Mobile Disk: PAMHD005 (5GB), PAMHD002 (2GB)

Standard

Continuous

● Details on individual items

• SmartMedia™:

TOSHIBA PDR-SM32 (32MB), PDR-SM64 (64MB)

TOSHIBA SD-M512 (512MB), SD-M256 (256MB),

SD-M128 (128MB)

• [PC card display] function

• If you set PC card display to Auto., the projector switches to wireless/card input

mode automatically when a PC card is plugged into the PC card slot. Although this

item is provided as one of slideshow options, the setting works the same way even

when a wireless LAN PC card is plugged into the PC card slot.

• If you set PC card display to Manual, the projector makes no response to the

plugging of a PC card into the PC card slot.

• SD memory cards:

• miniSD cards:

Adapters:

TOSHIBA SD-S64 (64MB), SD-S32 (32MB)

BUFFALO MCR-5A, RXD-A

The TOSHIBA IPC5019A SmartMedia™ PC card adapter is not ATA-compliant, and so

cannot be used by this projector.

• [Auto. demo] function

• If you set Auto. demo to On, the projector starts a slide show automatically when it

● Backing up data

Toshiba recommend that you back up the data on the memory PC card before use.

(Toshiba assume no liability for losses incurred by data lost through the use of this

projector.)

switches to the wireless/card input mode with a memory PC card plugged into the PC

card slot. The slide show displays the JPEG files stored in the root directory of the

memory PC card.

• If you set Auto. demo to Off, a thumbnail list

p.45

appears automatically on the

screen when it switches to the wireless/card input mode with a memory PC card

plugged into the PC card slot. Select and view desired JPEG image files.

Download from Www.Somanuals.com. All Manuals Search And Download.

Projecting images stored in a memory PC card (Continued)

• [Interval]

■ Automatic demonstration

You can set the display interval of time (in seconds or minutes) for slide shows to be

played automatically.

p.43

If you set Auto. demo to On in “Setting slideshow options”

a slide show automatically when it switches to the wireless/card input mode with a

, the projector starts

• [Display effect]

memory PC card plugged into the PC card slot according to the procedure in

p.21

When playing a slide show, the projector can give various display effects or transitions

“Mounting a PC card”

to each slide being displayed.

The transitions available are listed below:

• None

Display each slide normally.

• The slide show is played as set in “Setting slideshow options”.

• The slide show displays the JPEG files stored in the root directory of the memory PC

card.

• If you set PC card display to Auto, the projector starts a slide show automatically when

the power is turned on with a memory PC card plugged.

• Wipe

Display the next slide gradually upward (Wipe ↑), downward (Wipe ↓), to the left

(Wipe ←), or to the right (Wipe →), over the current slide.

• Dissolve

• To suspend the slide show, press the

button.Pressing it again resumes the slide show.

• To end the slide show, press the RETURN button. A thumbnail list will then be displayed.

Display the next slide gradually in a certain fixed block pattern over the current slide.

• Cover

Display the next slide as sliding upward (Cover ↑), downward (Cover ↓), to the left

(Cover ←), or to the right (Cover →), over the current slide.

• Checker

Display the next slide gradually from the left using checkered blocks over the current

slide.

• Zoom/Rotate zoom

Display the next slide by enlarging it gradually, either straight from the center (Zoom)

or while turning it starting from the center (Spin zoom), over the current slide.

• Belt wipe

Display the next slide gradually in stripes from both sides, over the current slide.

• Blind

Display the next slide, as if it opened like a window blind, over the current slide.

• [Play icon]

The slideshow icon can be displayed.

• Standard

The projector handles the slideshow icon as follows depending on the “On/Off”

setting of Icon on the projector’s menu.

Icon On: The projector displays the icon upon the start of playing a slide show and

turns it off after a few seconds.

Icon Off: The projector does not display the icon.

• Continuous

The projector keeps the icon displayed during the slide show.

Download from Www.Somanuals.com. All Manuals Search And Download.

Projecting images stored in a memory PC card (Continued)

■ Playing a slide show from a thumbnail list

Searching for a target file

• Use the

• If there are multiple pages of thumbnails, click the

the next page, and the button on the top row to go to the previous page.

buttons to move the orange frame over the desired file or folder.

Plugging a memory PC card.

If you set Auto. demo to Off in “Setting slideshow options”

button on the bottom row to go to

p.43

and plug a memory

PC card into the PC card slot according to the procedure in “Mounting a PC card”

• To open a folder, move the orange frame to the desired folder and press the

You can navigate down up to 5 levels using the same procedure.

Pressing the RETURN button returns you to the next or other upper level folder.

button.

p.21

, the projector starts loading data from the PC card to display a thumbnail list on

the screen when the projector switches to the wireless/card input mode. The screenshot

below is an example of the thumbnail list. The actual list will vary depending on the data

stored on your memory PC card.

Displaying slides

Thumbnail list number

Current list No./Total number of lists

• Pressing the

button with a file selected displays the image in that file only in full-

Current Folder Name

screen view on the screen as a slide. Pressing the

mode.

button enters the automatic play

• To return to the thumbnail list display screen, press the RETURN button.

Operation Guide

Current File Name

Previous page exists

Changing slides

Orange frame: currently

selected file or folder

Pressing the

buttons with a slide displayed changes slides.

(

: previous slide; : next slide. These buttons are not available during an automatic

play.)

Folder

Thumbnail image of

first file in folder

Rotating a slide

Pressing the

buttons with a slide displayed rotates the slide 90 degrees. The

File

rotation information is preserved as long as you remain in the current folder.

(

: Rotate left; : Rotate right. These buttons are not available during an automatic

Thumbnail

image of file

play.)

Next page exists

Notes

Symbols in the thumbnail list

• The thumbnail display order and slide order goes in order from shortest file name to

longest. If two file names have the same number of characters, they are ordered

numerically if numbers are used in the file name, and alphabetically otherwise.

• It is possible to give presentations without using a computer by converting presentations

created with Microsoft^®PowerPoint^®into JPEG files using the JPEG Conversion Tool,

and storing them on a memory PC card.

Note, however, that functions such as animation effects and hyperlinks cannot be used,

so it should be tested before the actual presentation.

Indicates that only folders are

inside the folder.

Indicates that there is no data to

be displayed in the folder.

Indicates that the JPEG or other

file is not supported.

Indicates that an unsupported

JPEG or other file is present.

p.57

Download from Www.Somanuals.com. All Manuals Search And Download.

Checking the projector status

Installing the applications

If you will use the wireless LAN PC card function, install the application on the supplied

CD-ROM onto your computer.

■ Status display

To check the current status of the projector, select Status display in step 2 in

“Projector settings”

p.36

. The following items of information will then be displayed.

■ System Requirements

Supported OS:

CPU:

RAM:

Windows^®2000, Windows^®XP

Pentium III 750 MHz or higher recommended

256 MB or more recommended

The name of the application currently running on the projector is displayed.

(Examples: Slide Show, Wireless Utility)

Screen area (resolution): 1024 by 768 pixels recommended

When no card is plugged ➔

■ Application Types and Major Functions

“Type” is displayed.

When a memory PC card is plugged ➔

“

Type/Free space/Status” are displayed.

Type/MAC address/DHCP/IP address/

Wireless Utility

When a wireless LAN PC card is plugged

➔

This application is used for wireless connections. Use it to send the images from the

computer’s screen to your projector, and display on the screen.

Subnet mask/Gateway” are displayed.

JPEG Conversion Tool

Use to convert JPEG and other files into a format that can be displayed as a slide show

using a memory PC card.

The firmware version number of the wireless/card feature is displayed.

Note

■ How to install

In the supplied CD-ROM, select the Applications folder, and run setup.exe. Follow the

instructions on your computer screen.

During the installation, a dialog box may appear with the message “Digital Signature

Not Found” and the prompt “Do you want to continue the installation?”. Click on the

[Yes (Y)] button to continue the installation.

• This product contains a piece of software (hereafter the Software) licensed to TOSHIBA

CORPORATION (hereafter TOSHIBA) by AXE, Inc. (hereafter AXE). The copyright and

other intellectual property rights of the software are held by AXE or the licensor.

The software is protected by the Copyright Law, Universal Copyright Convention, and

other intellectual property laws and agreements. The permission of AXE or the licensor

must therefore be obtained before the software can be reproduced.

Note, however, that the software is partly covered under the GNU General Public License

Version 2 (hereafter GPL2).You can obtain a copy of GPL2 at http://www.fsf.org/copyleft/

gpl.html. AXE will provide the GPL-covered source code of the software in accordance

with the terms of GPL2. Contact AXE if you need it.

When installation is finished, the following shortcuts will appear on your computer’s

desktop:

p.50

Wireless Utility →

Operations

p.55

JPEG Conversion Tool →

Operations

An OS of axLinux is a registered trademark of AXE, Inc.

■ How to uninstall

Select [Start Menu] → [Settings] → [Control Panel] → [Add/Remove Programs],

and remove Toshiba Data Projector from currently installed programs.

Note

• Your computer screen may temporarily go out during installation, but it is not an error.

Download from Www.Somanuals.com. All Manuals Search And Download.

Using the Wireless Utility

■ Displaying a computer’s screen via the projector

Select the screen image you wish

the projector to display.

Launch the Wireless Utility

software application.

Select Desktop

The computer screen image is transmitted as-is

When the Wireless Utility launches, the Screen

Image transmission mode window appears on

the computer screen.

To switch to the Screen Image transmission

mode window from another mode (File or

Projector Camera), click on the Screen Image

Select application window

Select a running application (e.g. Microsoft^®

PowerPoint^®), and send that application’s

window only.

The desktop and a list of running applications are displayed.

Select the desired application from this list. (If the desired

application is not on the list, launch it. Note that if too many

applications are running, it will consume the computer’s

resources, which could slow communication speed.)

icon

Select Transmission mode.

Click on Update automatically or Update manually. See step

Update automatically and Update manually.

for the meanings of

Select the projector to be

transmitted.

The IDs of projectors accessible for communication

will be listed. (When a projector name is set, that

name appears instead of MAC address.) Select the

checkbox of the projector you wish to transmit to

Click on the Advanced button.

The Screen Image: Advanced Settings dialog

appears. Set the dialog as shown below, as

necessary.

from this list. Then icon

projector’s screen for few seconds

It is possible to select up-to four projectors.

is displayed on the

• Interruption

Check the No Interruptions checkbox to prevent

other computers from interrupting the projector, for

example, during presentation in the Update

automatically mode.

Click on the

button.

When “Update automatically” is selected in step

Screen images are sent consecutively after the

When “Update manually” is selected in step

• Window

button is clicked.

Select the Place in Tasktray at the start of

transmission checkbox to iconify the Wireless

Utility and place it in the computer’s tasktray

when transmission initiated.

To display the window, double click on this icon, or

right click and select Open from the popup menu.

Even with the Wireless Utility window minimized,

you can use the pop-up menu to stop or resume

A single screen image is sent when the

button is clicked.

To halt transmission from Update automatically, click on the

button.

If the Wireless Utility icon has been placed in the tasktray, double click on the icon to

display the window, then halt transmission, or right click on the icon, and halt transmission

transmission as described in step

• Mode

Selecting High quality improves the quality of the

projected image, but lowers communication

speed. Selecting High speed has the opposite

effect.

and later

Notes

•

It may not be possible to transmit the images from movie player or other video applications

• When using “Update automatically”, the transmitted image refresh rate depends on the

performance of the computer you are using and the surrounding radio wave environment.

• The projector screen may have a few differences from the computer screen.

It is not possible to transmit to a projector that is already receiving from another computer

•

• If you selected application window in step , if that application is not active (in use), the

image may not be correctly displayed by the projector.

• The projector ID is the MAC address of the wireless LAN PC card inserted into the

projector.

Download from Www.Somanuals.com. All Manuals Search And Download.

Using the Wireless Utility (Continued)

■

Displaying a JPEG image saved on a computer via the projector

Select the projector to be

transmitted.

Launch the Wireless Utility software application.

The Screen Image transmission mode window appears on the computer’s screen.

The IDs of projectors accessible for

communication will be listed. (If projector name

has been set up already, it is shown instead of

the MAC address.) Select the checkbox of the

projector to be transmitted to from this list.

Click on the File icon

The Wireless Utility

window changes to File

transmission mode.

Then icon

is displayed on the projector’s

screen for few seconds.

It is possible to select up-to four projectors.

Click on the

button.

The selected file’s image is displayed by the projector.

Note

Click on the Browse button, and

select the file to send.

Clicking on the Browse button displays the Open

dialog box. Select the file to send, then click on

the Open button.

•

Only one file can be sent at a time. To send another file, repeat steps

and

■ Operating the projector

This function can be used with any projector input.

Note, however, that this will not function with a memory PC card.

The selected file is added to the pull-down list in

the Wireless Utility’s Transmission File field.

Launch the Wireless Utility software application.

The Screen Image transmission mode window appears on the computer’s screen.

Select the file to be sent from the

pull-down list of the Transmission

File field.

Click on the Remote

Control button.

The Remote Control window

appears.

Click on the Transmission File field’s

button to

display the pull-down list. Select the file to be sent

from this list.

A thumbnail of the selected file appears in the

Preview box. The file displayed here will be

transmitted.

As the Wireless Utility window is

still displayed, you can operate the

projector via the Remote Control

window, while using the Wireless

Utility’s functions.

Step

can be skipped.

The way that drag and drop the file to be sent from the desktop or Windows Explorer

into the Preview box is also available. In this case as well, the selected file is added to

the file pull-down list Transmission File field’s.

While it is possible to use this function merely to operate the projector, closing the

Wireless Utility also closes the Remote Control window.

Download from Www.Somanuals.com. All Manuals Search And Download.

Using the Wireless Utility (Continued)

How to use the JPEG Conversion Tool

The JPEG Conversion Tool converts JPEG files not supported by the projector, image

files in other formats, Microsoft^®PowerPoint^®files, and the like into JPEG files supported by

the projector. The JPEG files converted with this tool can be displayed by sending them

Select the projector to be operated.

In the Remote Control window, click on the

button, and

select the desired projector from the pull-down list. The remote

control screen will then change to the new one as shown on the

right. Only one projector can be selected. (It is not possible to

operate multiple projectors.)

p.52

p.42

using the wireless LAN PC card

, or saving them on a memory PC card

■ Launching the JPEG Conversion Tool

The window shown in the figure to the right appears on the

computer screen.

Drag the Image Quality Settings slider to the left or right to set the

image quality of the file after conversion. Lower values create

smaller files, but lower the image quality. (It is not possible to restore

the quality of an image after it has been lowered.)

■ Converting an image file

This converts JPEG files using compression formats not supported by the projector,

Windows^®metafiles (wmf), and bitmapped files (bmp) into JPEG files.

(1) In the Conversion Method field, select Converting image

file. (Status on launch)

(2) In the File settings field, click on the Browse button for

Original Image File Name.

The Open dialog box appears.

(3) In the Open dialog box:

(1)

Click on the Remote Control window’s buttons.

The function of each button and box is as follows:

Power On: Turns projector power on.

Power Off: Turns projector power off.

(2)

(5)

Input (box) : Click on the

button, and select the desired input from the pull-down

(a) Specify the location of the file to be converted; and

list.

(b) In the Files of Type field, click on the

the file format. A list of files of that format appear in the

Open dialog box.

button to select

Go:

Switches to the input selected in the Input box.

Freeze:

Mute:

+/–:

The picture is paused.

Cuts off picture and sound. Click again to restore picture and sound.

Adjust sound volume.

(7)-(a)

(4) In the Open dialog box, select the file to convert, then click

on the Open button.

(5) In the JPEG Conversion Tool window, in the File

settings field, select Browse for File name after

conversion. The Save As dialog box appears.

(6) In the Save As dialog box:

(3)-(a)

To quit, click on the

window.

button on the Remote Control

(4)

(3)-(b)

Performing this does not close the Wireless Utility window.

To exit both the Wireless Utility and the Remote Control, click on the

the Wireless Utility window.

(a) Specify the location in which to save the converted

file;

(b) Enter a file name of up to 8 characters in the File

Name field; and

button on

Note

(6)-(a)

p.39

(7) (a) In the JPEG Conversion Tool, click on the

Conversion button.

•

Remote control's functions can be restricted by setting Remote control

(6)-(b)

(6)-(c)

(b) A confirmation dialog box opens. Click Yes.

The computer converts the file. When it finishes a

message appears informing you that a JPEG file

has been created.

■ Document camera function

The document camera function is available for the Toshiba LCD data projector TLP-T701/

T721/T501/T521/T521E.

For details, consult your local dealer.

(7)-(b)

Download from Www.Somanuals.com. All Manuals Search And Download.

How to use the JPEG Conversion Tool (Continued)

■ Converting files created with Microsoft^®PowerPoint^®

■ Making a presentation with converted JPEG files

This process provides presentations without using a computer by converting

presentation files created with Microsoft^®PowerPoint^®into JPEG files, storing them on

a memory PC card, and displaying them in a slide show.

• To use this conversion mode, Microsoft^®PowerPoint^®must be installed on the

(1) Copy the folder created by the JPEG Conversion Tool, or its contents, onto a

memory PC card.

p.46

(2) Use the step

in “Playing a slide show from a thumbnail list”

to display a

list of thumbnails.

computer.

(3) Follow the instructions in step

in “Playing a slide show from a thumbnail list”

• Only static images are supported by this process. Animation and audio are not

supported.

Presentation files created with Microsoft^®PowerPoint^®usually

consist of several slides. For this reason, the tool creates a folder

with the name specified in step (5), below, and file for each slide

is created in the folder (starting with slide001.jpg).

p.47

to find the thumbnail of the first slide, Slide001.jpg, and move the orange

frame to it. (Select Slide001.jpg.)

(4) Press the

button on the remote control. An enlarged view of the first slide

appears on the screen. This starts the presentation.

(1)

(5) To continue to the next slide, press the remote control’s

previous slide, press the button.

button. To go back to the

(2)

(1) In the Conversion Method field, select Converting PPT

file.

(4)

■ Creating a screen capture and converting it into a JPEG file

(2) In the File settings field, click on the Browse button for PPT

File Name.

This function saves the current computer screen as a JPEG file.

The Open dialog box appears.

(1) In the Conversion Method field, select Creating screen

(9)-(a)

capture.

(3) In the Open dialog box:

(1)

(a) Specify the location of the file to be converted; and

(b) Select the PowerPoint^®presentation file to convert,

then click on the Open button.

(2) In the File settings field, click on the Browse button for File

name after conversion.

The Save As dialog box appears.

(3)-(a)

(2)

(4) In the JPEG Conversion Tool window, in the File

settings field, click on the Create button for New

folder name.

(3) In the Save As dialog box:

(3)-(b)

(5)

(a) Specify the location in which to save the converted file;

(b) Enter a file name of up to 8 characters in the File Name

field; and

The Folder create dialog box appears.

(4)-(a)

(5) In the Folder create dialog box, in the Folder Name of

(6)

document field, specify a folder name of 12 characters or less.

(4) (a) In the JPEG Conversion Tool window, click on the

Conversion button.

(b) A confirmation message appears. Click Yes.

(8)-(a)

(6) In the Folder create dialog box, click on the Selection button.

(3)-(a)

The Browse for Folder dialog box appears.

The computer creates a screen capture, and

(7) In the Browse for Folder dialog box:

(a) Specify the location in which to save the folder; and

(b) Click on the OK button.

(3)-(b)

(3)-(c)

converts it into a JPEG file in the specified location.

When it is finished, a message appears to tell you

that a JPEG file has been created.

(7)-(a)

(8) In the Folder create dialog box:

(a) Click on the Create button.

A confirmation dialog box appears;

(b) Click on the OK button.

(7)-(b)

(8)-(b)

(4)-(b)

Note

(9) (a) In the JPEG Conversion Tool window, click on the

Conversion button.

•

The maximum resolution of JPEG files created with the JPEG Conversion Tool is 1,024 ×

768 pixels.

(b) A confirmation dialog box opens. Click Yes.

The computer begins to convert the file. When it finishes,

a message appears informing you that a JPEG file has

been created.

(9)-(b)

Download from Www.Somanuals.com. All Manuals Search And Download.

Setting up the projector using a Web browser

■ How to use the “Projector Configuration Tool”

Select items from the menu on the left.

The “Projector Configuration Tool” uses the Web server features of the projector to

set up the projector using a wireless LAN PC card.

When using the “Projector Configuration Tool”, set up the wireless LAN connecting

the projector and the computer.

Setting:

Allows you to make various settings on the wireless/card

menu. When Browser authentication has been set to On,

access to the setup page requires the input of the password.

Displays some states of the projector.

Introduces the functions available in wireless/card input

mode.

Status Display:

Features:

p.48

See “Checking the projector status”

to display

Projector name:

Enter a character string and press the Set button, and it will

be set as the projector name.

information on the screen and write down the IP address.

Top:

Returns you to the top page.

TOSHIBA Projector Site

The browser will display the home page at http://

multimedia.projector-toshiba.com/map.html, providing

projector information. The home page address is subject to

change without notice.

(The Toshiba’s web site can be browsed only when your

computer can access the Internet.)

Invoke Internet Explorer.

Internet Explorer Ver. 5.0 or later is recommended. Enable the Javascript functions.

In the address bar, enter the IP address

“http://xxx.xxx.xxx.xxx/” recorded in step

The Web browser will then display the following page.

above.

● Details on major items

• Setting

Allows you to make various settings on the wireless/card menu. When Browser authentication

has been set to On, access to the setup page requires the input of the password.

Network:

The items available here are equivalent to those in the wireless/card

menu. Note, however, that security items such as “Remote control” and

“Browser authentication” cannot be set. Entering individual items and

press the Execute button to update their setting.

Projector name

Projector ID

Enter the projector

name to be registered.

Slide Show: The items available here are equivalent to those in the wireless/card

menu. Entering individual items and press the Execute button to update

their setting.

Projector name Projector ID

Note 1: To prevent access from third parties, the projector is restricted to permit access

only from the computer that has been set up for the TCP/IP to have the same

network address as the projector.

Note 2: If you use a proxy server, do not enable the proxy when accessing the above IP

address.

The TCP/IP settings for the projector and computer are required even in the

wireless LAN Ad hoc mode.

Press this button after entering

the password.

Discards what you have entered.

Download from Www.Somanuals.com. All Manuals Search And Download.

Setting up the projector using a Web browser (Continued)

• Features

Introduces the functions available in Wireless/Card input mode.

Slide Show

Wireless Utility

Displays the

Help page.

Updates the

settings.

Discards what

you have

entered.

Enter single-byte alphanumeric characters in text input fields.

• Status Display

Displays some states of the projector.

Projector:

Displays the contents of status display in the menu.

Wireless/Card: Displays the contents of status display in the Wireless/Card menu.

Maintenance: Describes an error if it occurs, for example, when the lamp has blown.

Download from Www.Somanuals.com. All Manuals Search And Download.

Maintenance

About lamp

The product’s light source is a mercury lamp that lights at increased internal pressure. Be sure

to fully understand the following characteristics of the lamp and handle it with extreme care.

• The lamp may burst with a loud noise due to impact or deterioration, or fail to light at

the expiration of its life.

• How long it takes before the lamp bursts or the life expires may vary greatly by lamp.

Some may burst shortly after first use.

• Burst is likely to happen if the lamp is used after the replacement period has elapsed.

• When the lamp bursts, the broken pieces of glass may get inside the product or be

released outside from the openings for ventilation.

• When the lamp bursts, a slight amount of mercury gas enclosed in the lamp along with

glass dust may be released from the openings for ventilation.

Unplug power cord.

Wait until lamp is sufficiently cooled.

Wait for at least 1 hour.

Remove the lamp cover.

Lamp cover

Loosen the 1 screw, then pull up to the direc-

tion of the arrow with your fingers as shown to

remove the lamp cover. Use care to avoid any

damage to nails and/or tip of your finger(s). (If

you have any difficulty in removal, you can use

a screwdriver or any other smaller tool for your

convenience.)

■

Immediately replace the lamp when a sign appears on the screen.

• When the replacement time approaches, a message will appear on the screen.

• The risk of burst will increase if the lamp is continuously used without being replaced.

• Frequently check the used hours and prepare spares when the replacement time

Pull out the lamp.

Loosen the 2 screws holding the lamp in place,

and pull up the handle to remove the lamp.

p.33

approaches. (Refer to “Status display”.

)

■

When the lamp is broken

• If glass components, including a lamp and a lens, should break, handle the broken

pieces with care to avoid injury and contact your dealer for repair service.

• In the event of lamp burst, unplug the product from the wall outlet, leave and completely

ventilate the room. Then, thoroughly clean the area around the projector and discard

any edible items placed in that area.

Mount the new lamp.

Align the orientation, press down until the bottom is

reached, and lock in place using the two lamp

locking screws.

• When the lamp bursts, consult a doctor if glass dust or mercury gas gets into your eyes

or you breathe it.

Replace the lamp cover.

Align the cover, and press it in, then tighten the

Lamp replacement

A lamp is consumable supplies. If used for extended periods, images will appear dark, and

the lamp could burn out. This is characteristic of a lamp, and is not malfunction. (The lifetime

screws loosened in step

no longer loose.

until the lamp cover is

Reset the lamp timer.

See the lamp’s manual for instructions on resetting

the lamp timer.

of the lamp depends on condition of use.) If this happens, replace it with a new one

WARNING

•

If the projector is mounted on a ceiling, request a lamp replacement from your projector dealership.

Notes and Precautions

• When replacing, always use lamp “TLPLW3A” (sold separately).

p.33

• Lamp time in the Status display menu indicates lamp uptime (reference value)

• It is recommended that the lamp be replaced after 2,000 hours of use. When Lamp time

reaches 2,000 hours, the icon and a message will appear. This display disappears

when you press button.

CAUTION

• Attach the lamp cover correctly so that it is not loose. If it is not attached correctly, the

•

If you have been using the projector, the lamp will be very hot, and may cause burn injuries

Wait for the lamp to cool (for longer than 1 hour) before replacing it.

If the lamp should break, please handle with care to avoid injury due to broken pieces and

contact your dealer for repair service.

p.65

lamp may fail to come on

, and the lamp’s lifetime may be shortened.

• Always replace the lamp with a new one.

• The lamp is made out of glass. Do not touch the glass surface with your bare hands,

bang it, or scratch it. (Dirt, jolts, scratches and the like could break the lamp.)

Download from Www.Somanuals.com. All Manuals Search And Download.

Others

Lamp replacement (Continued)

Trouble indications

The indicator lights inform you of internal abnormalities.

Used Lamps

This projector’s lamps contain trace amounts of environmentally harmful inorganic

mercury. Be careful not to break used lamps, and dispose of them in accordance with

local regulations.

No power

⇒ Problem with projector

• Unplug the power cord, and contact your dealer.

⇒ The lamp cover is not properly attached.

p.63

• Unplug the power cord, and reattach the lamp cover.

(Off)

Lens and main unit cleaning

Lamp went out during use, or won’t come on

⇒ Lamp temperature is high so that it is difficult to turn on, the lifetime of

the lamp has ended or the projector is malfunctioning.

(Red lit)

•

Unplug the power cord and wait for a short while, then turn the power back on.

WARNING

• If a lamp burns out, replace it with a new one.

❈ After approx. one minute of abnormal display, the projector returns to

the standby state waiting for internal cool down.

•

Request cleaning and maintenance of a ceiling-mounted unit from your projector dealership.

(Red lit)

Attempting to clean/replace the lamp at a high site by yourself may cause you to drop

down, thus resulting in injury.

Power went out during use

⇒ Internal overheating, or the outside temperature is too high.

• Place the projector so that the air intake and exhaust are not blocked.

(Red lit or flashing)

Or (Orange lit)

(Green lit)

■ Lens cleaning

•

Unplug the power cord and wait for a short while, then turn the power back on.

• Clean the lens with a commercially available blower and/or

❈ The icon will appear before the power goes out.

❈ After approx. one minute of abnormal display, the projector returns to

lens cleaner.

(Red lit)

the standby state waiting for internal cool down.

• The lens is easily scratched, so do not rub it with hard objects,

or strike it.

Power went out during use

⇒ Problem with internal cooling fan.

• Unplug the power cord, and contact your dealer.

(Red lit or flashing)

Or (Orange lit)

■ Main unit cleaning

❈ The

icon will appear before the power goes out.

• Clean the main unit after unplugging the power cord.

• Wipe dirt off the main unit gently with a soft cloth.

• Do not wipe the main unit with a damp cloth. Doing

so may allow water to get inside, resulting in an

electric shock or failure.

• Do not use benzene, thinner and the like as they may

deform or discolor the unit or damage the paint

surface.

❈ After approx. one minute of abnormal display, the projector returns to

the standby state waiting for internal cool down.

(Red lit)

Power went out during use

⇒ Problem inside the projector.

(Green lit

or Off)

•

Unplug the power cord and wait for a short while, then turn the power back on.

(Green lit

or Off)

(Green

flashing)

• If the above action will not clear the problem, unplug the power cord,

and contact your dealer.

❈ After approx. one minute of abnormal display, the projector returns to

the standby state waiting for internal cool down.

(Red lit)

• When using a chemically treated cloth, follow the

precautions included with the cloth.

PRECAUTION

• Make sure to unplug the power cord if something goes wrong.

Download from Www.Somanuals.com. All Manuals Search And Download.

Before calling service personnel

If you think something is wrong, check the followings before contacting customer service.

If This Happens

Check

p.65

Please see “Trouble indications”

as well.

• Is the memory PC card inserted correctly?

Memory PC card

images aren't

projected

p.42

If This Happens

Check

• Is a PC card not supported by the projector inserted?

p.21

• Is the CARD indicator red?

• Is the power cord plugged in? Is it connected to the projector?

• Is the lamp cover loose?

No power

• Are there any JPEG files saved on the memory PC card?

• Are the files too large or in an unsupported format for the projector?

Convert them with the supplied software application.

p.63

p.65

• Is the ambient temperature high?

Power goes out

during use

p.55

p.65

• Is the air intake or air exhaust blocked?

• Is the wireless LAN PC card inserted correctly?

• Is a wireless LAN PC card not supported by the projector inserted?

The operation of cards other than the supplied product is not

guaranteed.

The wireless

LAN PC card

doesn't work

p.24

• Is the projector turned on?

• Is the mute function on?

No picture

p.28

p.30

• Is the brightness setting minimized?

• Are the connections set up correctly?

• Are all the connected devices functioning properly?

p.20

p.21

• Is the CARD indicator red?

• Are the transmission mode and channel properly configured?

p.38

p.24

• Is the projector turned on?

• Is the mute function on?

No audio

• Are there any obstructions between the computer and projector?

• Do your computer and OS support the supplied software

p.28

p.25

p.49

• Is the volume setting minimized?

• Are the connections set up correctly?

application?

p.20

• Are all the connected devices functioning properly?

p.69 p.70

• Is the input signal supported by the projector?

Picture not

displayed

correctly

• Is there something generating an abnormal video signal, for

instance the video tape?

p.64

• Is the lens dirty?

Picture blurred

Part of picture

out of focus

p.25

• Is the lens focus adjusted optimally?

• Is the projection distance within the projector’s supported range?

p.19

• Is the projector’s screen placement angle tilted too far?

p.27 p.30

• Are the sharpness or sampling phase adjustments off?

p.30

• Are the brightness or contrast adjustments off?

• Is the lamp nearing the end of its service life?

Image is dark

p.33

p.30

• Are the color, tint, R-level, G-level, or B-level adjustments off?

• Is the screen dirty?

• Is the lamp nearing the end of its service life?

Colors too light

Bad shading

p.33

• Are the remote control’s batteries drained?

Remote control

doesn’t work

p.18

• Are the batteries inserted into the remote control correctly?

• Is the remote control being used within the effective range?

• Are there any obstructions between the remote control and

projector?

p.18

• Are there any fluorescent or other bright lights shining at the

projector’s infrared remote sensor?

Download from Www.Somanuals.com. All Manuals Search And Download.

Specifications

■ List of general specifications

■ List of supported signals (RGB signals)

This projector supports the following RGB signals. Note, however, that depending on the

Item

Specification

computer model, the screen may show flicker or streaking. Please adjust the projector if

Consumption Power

Weight

External Dimensions

(including protruding parts)

Cabinet material*

300 W

2.9 kg

this happens.

p.26 p.27

(Press the SET UP button, and adjust automatically or manually.

)

298 × 101.4 × 275.4 mm (W × H × D)

Refresh rate

(Hz)

H-frequency

Clock

(MHz)

PC+ABS resin and ABS resin

Resolution

Mode

(kHz)

37.927

31.469

37.861

37.500

43.269

35.156

37.879

48.077

46.875

53.674

49.725

48.363

56.476

60.023

68.667

60.134

67.500

60.000

85.938

63.981

79.976

91.146

63.973

75.000

81.250

87.500

93.750

106.250

Conditions for usage environment Temp: 5°C to 35°C; relative humidity: 30% to 70%

720 × 400

640 × 480

720x400_85

VGA_60

VGA_72

VGA_75

VGA_85

SVGA_56

SVGA_60

SVGA_72

SVGA_75

SVGA_85

MAC16"

85.039

59.940

72.809

75.000

85.008

56.250

60.317

72.188

75.000

85.061

74.550

60.004

70.069

75.029

84.997

74.700

75.000

60.000

85.002

60.020

75.025

85.024

60.012

60.000

65.000

70.000

75.000

85.000

35.500

25.175

31.500

36.000

40.000

50.000

49.500

56.250

57.283

65.000

75.000

78.750

94.500

79.857

108.000

148.500

108.000

135.000

157.500

118.094

162.000

175.500

189.000

202.500

229.500

Display pixels

Picture elements

Lens

1 chip DMD™

786,432 pixels (1024H × 768V)

Zoom lens

High-pressure mercury lamp

30.75-246 inches

1.50-10.00 m

F=2.75-3.00 f=22.25-26.69 mm

Lamp

Projection screen size

Projection distance

Speaker

800 × 600

1 W (Monaural)

COMPUTER-1 terminal Mini D sub 15 pin RGB / Y/PB/PR (dual use)

COMPUTER-2 terminal Mini D sub 15 pin RGB / Y/PB/PR (dual use)

MONITOR terminal

S-VIDEO terminal

AUDIO (L/R) terminal

VIDEO terminal

Mini D sub 15 pin RGB / Y/PB/PR (dual use)

Mini DIN 4 pin

RCA Pin Jack × 2, 1.5 V (rms), 22 kΩ or more

RCA Pin Jack, 1 V (p-p), 75 Ω

ø3.5mm dia. stereo mini-jack, 1.5V (rms); 22 kΩ or more

ø3.5mm dia. stereo mini-jack

Mini DIN 8 pin (RS-232C)

832 × 624

1024 × 768

XGA_60

XGA_70

XGA_75

XGA_85

AUDIO IN terminal

AUDIO OUT terminal

CONTROL terminal

PC card slot

MAC19"

1152 × 864

1280 × 960

SXGA1_75

QuadVGA_60

QuadVGA_85

SXGA3_60

SXGA3_75

SXGA3_85

SXGA+

UXGA_60

UXGA_65

UXGA_70

UXGA_75

UXGA_85

Compliant with PC Card Standard TYPE II

* Each plastic part displays the materials it is made from, in order to facilitate recycling after this

product becomes no longer usable.

1280 × 1024

■ Separately sold product

1400 × 1050

1600 × 1200

Replacement Lamp

Model TLPLW3A

Note

• Design, specifications, etc. subject to change without notice for improvements, etc.

Note

• Signals which resolution exceeds the native resolution (1024 × 768 pixels) will be

compressed. For this reason, some information may be lost, or image quality may be

affected.

Download from Www.Somanuals.com. All Manuals Search And Download.

Specifications (Continued)

■ List of supported signals (Y/PB/PR signals)

■ CONTROL terminal

Signal format

fh(kHz)

15.73

31.47

15.63

31.25

45.00

37.50

33.75

28.13

33.75

31.25

fv(Hz)

59.94

50.00

60.00

50.00

60.00

50.00

60.00

50.00

● Pin assignment

480i(525i)@60Hz

480p(525p)@60Hz

576i(625i)@50Hz

576p(625p)@50Hz

720p(750p)@60Hz

720p(750p)@50Hz

1080i(1125i)@60Hz

1080i(1125i)@50Hz

1035i(1125i)@60Hz

1152i(1250i)@50Hz

Pin No.

Signal Name

RXD

Description

Receiving data

Consent to send

Data set ready

Signal ground

Request to send

No connection

Sending data

CTS

DSR

GND

RTS

N.C

TXD

GND

Signal ground

Mini DIN 8 pin connector

● Interface format

1 Communication method RS-232C, 9600bps, No Parity, Data Length: 8 bits;

■ List of supported signals (Video, S-Video signals)

Stop Bit Length: 1 bit

STX (02h) Command (3Byte) ETX (03h)

Only 1 command valid per communication.

For input commands, only ASCII-compliant all-uppercase

alphanumeric characters supported.

Video mode

NTSC

fh(kHz)

15.73

15.63

15.73

15.63

15.73

fv(Hz)

fsc(MHz)

3.58

2 Communication format

3 Data format

PAL

4.43

SECAM

PAL-M

4.25 or 4.41

3.58

4 Replies

Acknowledge

ACK (06h) CR (0Dh) Data ... Normally ended

PAL-N

3.58

ACK (06h) ESC (1Bh)

NAK (15h)

... Aborted

PAL-60

NTSC4.43

4.43

No acknowledge

If commands are to be sent consecutively, wait for the response from the projector

before sending the next command.

■ Pin assignment of COMPUTER-1/2 & MONITOR terminals

● Main Commands

No.

Pin description

During Y/PB/PR input

Item

Command

IN1

Item

Command

PON

During RGB input

Video signal (R)

Video signal (G)

Video signal (B)

GND

Computer (1) input select

Computer (2) input select

Video input select

Power on

Power off

Icon display on

Color difference signal (PR

)

IN2

IN3

POF

MO0

Luminance signal (Y)

Color difference signal (PB)

S-video input select

PC card input select

IN4

IN5

Icon display off

MO1

PAT

∗

Auto setting (RGB input)

Status display on

Status display off

GND

DON

DOF

GND (R)

GND (PR

)

Mini D sub 15 Pin connector

GND (G)

GND (Y)

GND (B)

GND (PB)

Input Signal

• RGB input

RGB signals:

Horizontal sync signal: TTL level (Pos/neg polarity)

Vertical sync signal: TTL level (Pos/neg polarity)

• Y/P^B/PR input

Note

N.C

∗

• Contact your dealer for control cable and other commands.

GND

0.7V (p-p) 75 Ω

GND

N.C

Horizontal sync signal

Vertical sync signal

N.C

Y signal:

P^B/PR signals:

1.0V (p-p) 75 Ω

0.7V (p-p) 75 Ω

∗ Do not connect anything.

Download from Www.Somanuals.com. All Manuals Search And Download.

Toto Computer Hardware LVU2E1 User Manual
Tripp Lite Network Cables S455 003 User Manual
Tripp Lite Network Card U218 000 R User Manual
Tripp Lite Power Supply 1400 3000 VA User Manual
Tripp Lite Surge Protector TLP808NETG User Manual
Ultimate Ears DVD Player PD 500 User Manual
Venturer Flat Panel Television PLV76198E User Manual
Vidikron Projection Television Vision 65 User Manual
Viking Sprinkler Sprinkler 11a User Manual
Vizio Computer Accessories CPU 56 User Manual