Toshiba Projection Television 46H83 User Manual
OWNER'S MANUAL  
Projection Television  
I
46H83  
51H83  
57H83  
65H83  
Owner's Record  
The model number and serial number are on the back  
of your TV. Record these numbers in the spaces below.  
Refer to these numbers whenever you communicate  
with your Toshiba dealer about this TV.  
Model:  
Serial No.:  
23565901A  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Important Safety Instructions  
Installation, Care, and Service  
1) Read these instructions.  
2) Keep these instructions.  
3) Heed all warnings.  
Installation  
Follow these recommendations and precautions and heed all  
warnings when installing your TV:  
4) Follow all instructions.  
16) Never modify this equipment. Changes or modifications  
may void: a) the warranty, and b) the user’s authority to  
operate this equipment under the rules of the Federal  
Communications Commission.  
5) Do not use this apparatus near  
water.  
17)  
DANGER: RISK OF SERIOUS PERSONAL  
INJURY, DEATH, OR EQUIPMENT  
DAMAGE! Never place the TV on  
6) Clean only with a dry cloth.  
an unstable cart, stand, or table. The TV  
may fall, causing serious personal injury,  
death, or serious damage to the TV.  
7) Do not block any ventilation  
openings. Install in accordance with  
the manufacturer’s instructions.  
18) Never place or store the TV in direct  
sunlight; hot, humid areas; areas  
subject to excessive dust or vibration;  
or locations with temperatures at or  
below 41°F (5°C).  
8) Do not install near any heat  
sources such as radiators,  
heat registers, stoves, or other  
apparatus (including amplifiers)  
that produce heat.  
9) Do not defeat the safety purpose of the polarized or  
grounding type plug. A polarized plug has two blades  
with one wider than the other. A grounding type plug has  
two blades and a third grounding  
19) Always place the TV on the floor  
or a sturdy, level, stable surface that  
can support the weight of the unit.  
Wide plug  
prong. The wide blade or the third  
prong are provided for your safety.  
If the provided plug does not fit into  
your outlet, consult an electrician  
for replacement of the obsolete outlet.  
20) Never place items such as vases,  
aquariums, or candles on top of the TV.  
10) Protect the power cord from being  
walked on or pinched, particularly at  
plugs, convenience receptacles, and  
the point where it exits the apparatus.  
11) Only use attachments/accessories specified by the  
21) Never block or cover the slots or  
openings in the TV cabinet back,  
bottom, and sides. Never place  
the TV:  
manufacturer.  
12) Use only with the cart, stand, tripod,  
bracket, or table specified by the  
manufacturer, or sold with the  
• on a bed, sofa, rug, or similar  
surface;  
• too close to drapes, curtains,  
or walls; or  
apparatus. When a cart is used, use  
caution when moving the cart/apparatus  
combination to avoid injury from tip-over.  
• in a confined space such as a  
bookcase, built-in cabinet, or any  
other place with poor ventilation.  
The slots and openings are provided  
to protect the TV from overheating  
and to help maintain reliable  
operation of the TV.  
13) Unplug this apparatus during  
lightning storms or when  
unused for long periods  
of time.  
14) Refer all servicing to qualified service personnel.  
Servicing is required when the apparatus has been  
damaged in any way, such as power supply  
cord or plug is damaged, liquid has  
22) Never allow anything to rest on or roll over the power  
cord, and never place the TV where the power cord is  
subject to wear or abuse.  
been spilled or objects have fallen into  
the apparatus, the apparatus has been  
exposed to rain or moisture, does not  
QUALIFIED  
SERVICE  
operate normally, or has been dropped.  
TECHNICIAN  
23) Never overload wall outlets and  
extension cords.  
15) CAUTION: To reduce the risk of electric shock, do not  
use the polarized plug with an extension cord, receptacle,  
or other outlet unless the blades can be inserted  
completely to prevent blade exposure.  
0303  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
30) [This item applies to projection TVs only.] If the air  
temperature rises suddenly (for example, when the TV is  
first delivered), condensation may form on the lenses. This  
can make the picture appear distorted or the color appear  
faded. If this happens, turn off the TV for 6 to 7 hours to  
allow the condensation to evaporate.  
24) Always operate this equipment from  
a 120 VAC, 60 Hz power source only.  
31) For added protection of your TV from lightning and power  
surges, always unplug the power cord and disconnect the  
antenna from the TV if you leave the TV unattended or  
unused for long periods of time.  
25) Always make sure the antenna system is properly  
grounded to provide adequate protection against voltage  
surges and built-up static charges (see Section 810 of the  
National Electric Code).  
Antenna lead-in wire  
32) During normal use, the TV may make  
occasional snapping or popping  
Antenna discharge unit  
(NEC Section 810-20)  
Ground clamp  
sounds. This is normal, especially  
when the unit is being turned on or  
off. If these sounds become frequent  
or continuous, unplug the power cord  
and contact a Toshiba Authorized Service Center.  
Grounding conductors  
(NEC Section 810-21)  
Electric service equipment  
Power service grounding  
33) Possible Adverse Effects on TV Picture Tube: If a fixed  
(non-moving) pattern remains on the TV screen for long  
periods of time, the image can become permanently  
engrained in the picture tube and cause subtle but  
permanent ghost images. This type of damage is NOT  
COVERED BY YOUR WARRANTY. Never leave your TV  
on for long periods of time while it is displaying the  
following formats or images:  
electrode system (NEC Art 250 Part H)  
Ground clamps  
26)  
DANGER: RISK OF SERIOUS PERSONAL  
INJURY OR DEATH!  
• Use extreme care to make sure you are never in  
a position where your body (or any item you are in contact  
with, such as a ladder or screwdriver) can accidentally  
touch overhead power lines. Never locate the antenna  
near overhead power lines or other electrical circuits.  
• Never attempt to install any of the following during  
lightning activity:  
a) an antenna system; or b) cables, wires, or any home  
theater component connected to an antenna or phone  
system.  
• Fixed Images, such as PIP/POP windows, stock tickers,  
video game patterns, TV station logos, and websites.  
• Special Formats that do not use the entire screen. For  
example, viewing letterbox style (16:9) media on a  
normal (4:3) display (gray bars at top and bottom of  
screen); or viewing normal style (4:3) media on a  
widescreen (16:9) display (gray bars on left and right  
sides of screen).  
Care  
Service  
34)  
For better performance and safer operation of your TOSHIBA  
TV, follow these recommendations and precautions:  
WARNING: RISK OF ELECTRIC  
SHOCK! Never attempt to service the  
TV yourself. Opening and  
27) Always sit approximately 10–25 feet away from the TV and  
as directly in front of it as possible. The picture can appear  
dull if you sit too far to the left or right of the TV, or if  
sunlight or room lights reflect on the screen. Turn the TV  
off to check for reflections on the screen, and then remove  
the source of reflections while viewing the TV.  
removing the covers may expose  
you to dangerous voltage or other  
hazards. Refer all servicing to a  
Toshiba Authorized Service Center.  
QUALIFIED  
SERVICE  
TECHNICIAN  
35) If you have the TV serviced:  
• Ask the service technician to use only replacement parts  
specified by the manufacturer.  
• Upon completion of service, ask  
the service technician to perform  
routine safety checks to determine  
that the TV is in safe operating  
condition.  
28) Always unplug the TV before  
cleaning. Never use liquid or  
aerosol cleaners.  
36) When the TV reaches the end of its useful life, ask a  
qualified service technician to properly dispose of the TV.  
Improper disposal may result in a picture tube implosion  
and possible personal injury.  
29)  
WARNING: RISK OF ELECTRIC SHOCK!  
Never spill liquids or push objects of any kind  
into the TV cabinet slots.  
4
0303  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Important Safety Precautions for Split Cabinet Feature  
(Models 57H83 and 65H83 only)  
1) Always handle and treat the top section of the TV cabinet  
Toshiba TV models 57H83 and 65H83 have a split cabinet  
feature that allows disassembly of the cabinet into two  
sections during installation.  
(with the viewing screen), which contains a glass mirror,  
with great care. If subjected to excessive mechanical  
abuse (for example, if bumped or dropped), the mirror  
may break, creating exposed glass fragments with sharp  
edges. Contact with these glass fragments may result in  
injury.  
For details, please refer to the insert titled “Disassembly/  
Reassembly Instructions for Split Cabinet Feature” that  
accompanied this owner’s manual in the accessory pack.  
If you do not have the insert, you can download a copy of  
it from our Web site (www.toshiba.com/tacp in the U.S.A.  
or www.toshiba.ca in Canada). If you do not have access  
to the Internet, call 1-800-631-3811 in the U.S.A. or 1-800-  
268-3404 in Canada.  
2) Never temporarily locate the disassembled bottom section  
in an area where it may be exposed to foreign objects or  
abuse (for example, areas where children may be playing,  
where items may fall on top of the unit, or where liquids  
may spill into the unit). Failure to follow this instruction  
may result in damage to the optic components of the TV.  
SUCH DAMAGE IS NOT COVERED UNDER THE  
TOSHIBA LIMITED WARRANTY.  
WARNING: If you split the cabinet for any  
purpose, NEVER energize the bottom section  
until it is completely and properly installed.  
Energizing the disassembled bottom section and  
subjecting it to intentional misuse (for example, exposing it to  
a foreign object) creates the potential for an electrical shock  
hazard that could result in death or serious injury.  
3) Always keep the top and bottom sections of the TV  
cabinet in an upright position while disassembled. Failure  
to follow this instruction may result in damage to the TV,  
including but not limited to the optic components, cabinet,  
bezel, and glass mirror. SUCH DAMAGE IS NOT  
CAUTION: If you use the split cabinet feature, ALWAYS  
handle and treat the top section of the TV cabinet, which  
contains a glass mirror, with great care. If subjected to  
excessive mechanical abuse (for example, if bumped or  
dropped), the mirror may break, creating exposed glass  
fragments with sharp edges. Contact with these glass  
fragments may result in injury.  
COVERED UNDER THE TOSHIBA LIMITED WARRANTY.  
4) Never energize the bottom section of the TV cabinet  
while disassembled. Failure to follow this instruction  
could result in death or serious injury.  
5) Never place anything on top of the disassembled bottom  
section of the TV cabinet. Failure to follow this instruction  
may result in damage to the optic components. SUCH  
DAMAGE IS NOT COVERED UNDER THE TOSHIBA  
LIMITED WARRANTY.  
Installation, Care, and Service  
CAUTION: The split cabinet feature (models 57H83 and  
65H83 only) allows disassembly of the cabinet into two  
sections during installation. If you use the split cabinet  
feature, follow these precautions while the two sections of  
the TV cabinet are disassembled:  
6) Never store or transport the unit while it is disassembled.  
Failure to follow this instruction may result in damage to  
the TV, including but not limited to the optic components,  
cabinet, bezel, and glass mirror. SUCH DAMAGE IS NOT  
COVERED UNDER THE TOSHIBA LIMITED WARRANTY.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the POP double-window feature .......................... 34  
Switching the main and POP pictures..................... 35  
Freezing the POP picture ........................................ 35  
Adjusting the size of the double-window................. 35  
POP double-window aspect ratio ............................ 36  
Using the programmed channel search function............. 36  
Using the favorite channel search function .............. 37  
About the auto favorite feature................................ 37  
Using the LOCKS menu ............................................... 38  
Entering the PIN code ............................................ 38  
If you cannot remember your PIN code .................. 38  
Using the V-CHIP menu ............................................... 39  
ENABLE BLOCKING .......................................... 39  
TV RATING (Independent rating system for  
Important Safety Information ............................. 2-5  
Introduction................................................................ 7  
Welcome to Toshiba......................................................... 7  
Exploring your new TV ................................................... 7  
Note regarding Quick Connect Guide........................ 7  
Connecting your TV .................................................. 8  
Connecting a VCR .......................................................... 8  
Connecting a cable converter box .................................... 9  
Connecting a cable converter box and VCR ..................... 9  
Connecting a DVD player or satellite receiver and  
a VCR............................................................................ 10  
Connecting a DVD player with ColorStream®  
(component video) and a VCR ...................................... 11  
Connecting a DTV receiver/set-top box with  
ColorStream® (component video) and a VCR ................ 12  
Connecting two VCRs ................................................... 13  
Connecting a camcorder ................................................ 13  
Connecting a device to the DVI/HDCP input .............. 14  
Connecting an audio system .......................................... 15  
Connecting an A/V receiver ........................................... 15  
broadcasters) ........................................................... 39  
MPAA RATING (Independent rating system for  
movies) ................................................................... 40  
BLOCKING OPTION .......................................... 40  
Unlocking programs temporarily ............................ 41  
Locking channels ........................................................... 41  
Locking video inputs ..................................................... 42  
Using the game timer ..................................................... 43  
Using the front panel lock feature .................................. 43  
Changing the PIN code ................................................. 43  
Adjusting the picture ..................................................... 44  
Selecting the picture mode ...................................... 44  
Adjusting the picture quality ................................... 44  
Saving your new preferences ................................... 45  
Using the ALS (Ambient Light Sensor) feature ....... 45  
Using the flesh tone feature ..................................... 46  
Using the CableClear™ DNR feature .................... 46  
Selecting the color temperature ............................... 46  
Selecting the display format (480p signals only) ...... 47  
Resetting your picture adjustments ......................... 47  
Selecting the cinema mode...................................... 47  
Selecting the video input source ..................................... 48  
Labeling the video input sources .................................... 48  
Using the closed caption feature..................................... 49  
Setting the ON timer ..................................................... 50  
Setting the sleep timer.................................................... 50  
Setting the clock ............................................................ 51  
Adjusting the sound ....................................................... 52  
Muting the sound ................................................... 52  
Selecting stereo/SAP broadcasts .............................. 52  
Using the WOW™ surround sound feature ........... 53  
Adjusting the sound quality .................................... 53  
Resetting your audio adjustments ........................... 54  
Using the sub-bass system (SBS) ............................. 54  
Turning off the built-in speakers ............................. 55  
Selecting the Audio OUT sound ............................. 55  
Using the StableSound® feature .............................. 56  
Selecting the background of the menu display ............... 56  
Displaying on-screen information .................................. 56  
Viewing the demo mode ................................................ 57  
Understanding the auto power off feature ...................... 57  
Understanding the last mode memory feature ................ 57  
Using the remote control ...................................... 16  
Preparing the remote control for use .............................. 16  
Installing the remote control batteries ............................ 16  
Programming the remote control to operate a cable  
converter box, satellite receiver, VCR, DVD player,  
or HTIB (home theater in a box) ................................... 17  
Remote control codes .............................................. 17–18  
Using the remote control to operate a cable converter  
box, satellite receiver, VCR, DVD player, or HTIB  
(home theater in a box) .................................................. 19  
Learning about the remote control ................................. 20  
Setting up your TV .................................................. 21  
Learning about the menu system ................................... 21  
Changing the on-screen display language ....................... 22  
Selecting the antenna input............................................ 22  
Adding channels to the TV’s memory ............................ 23  
Programming channels automatically...................... 23  
Adding and erasing channels manually.................... 23  
Using the Quick Connect Guide ................................... 24  
Changing channels ........................................................ 25  
Changing channels using SpeedSurf ........................ 25  
Adjusting the color convergence..................................... 25  
Automatically adjusting the color convergence  
using TouchFocus™ ............................................... 25  
Manually adjusting the color convergence............... 26  
Using the TV’s features.......................................... 27  
Adjusting the channel settings........................................ 27  
Switching between two channels using Channel  
Return .................................................................... 27  
Switching between two channels using  
SurfLock™............................................................. 27  
Programming your favorite channels ....................... 27  
Labeling channels ................................................... 29  
Viewing the wide-screen picture formats (480i and  
480p signals only) ....................................................... 30  
Selecting the picture size ......................................... 30  
Scrolling the Theater Wide picture  
Appendix................................................................... 58  
Specifications ................................................................. 58  
Troubleshooting ............................................................. 59  
Limited United States Warranty ..................................... 60  
Limited Canada Warranty.............................................. 61  
(Theater Wide 2 and 3 only) .................................. 32  
Using the AUTO ASPECT feature (480i only) ....... 33  
Index .......................................................................... 63  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
Introduction  
Welcome to Toshiba  
Congratulations! You have purchased one of the finest projection TVs  
on the market. The goal of this manual is to guide you through  
setting up and operating your Toshiba TV as quickly as possible.  
Note regarding  
Quick Connect Guide  
This manual applies to models 46H83, 51H83, 57H83, and 65H83.  
Before you start reading, check the model and serial numbers on the  
back of your TV. Write these numbers in the space provided on the  
front cover of this manual for your records.  
The Quick Connect Guide  
automatically appears on-screen  
the first time the TV is turned on.  
This feature provides on-screen  
instructions to guide you through  
initial setup of your TV.  
Instructions in this manual are based on using the remote control.  
You can also use the controls on the TV if they have the same name as  
those on the remote control.  
To stop the Quick Connect  
Guide, either press EXIT or turn off  
the TV.  
Please read all the safety and operating instructions carefully, and keep  
the manual for future reference.  
See page 24 for details.  
Exploring your new TV  
You can operate your TV using the buttons on the front panel or the  
remote control. The back panel and front panel (behind the door)  
provide all the terminal connections you will need to connect other  
equipment to your TV. See “Connecting your TV” on pages 8–15.  
Illustrations represent 57H83.  
Remote control  
Remote sensor (Behind the screen)  
Front  
POWER  
RECALL  
INFO  
TV/VIDEO  
Volume x •  
Power  
TouchFocus™  
indicator  
Channel zy  
1
4
2
5
8
3
6
9
CHRTN  
7
+10  
L/MONO  
AUDIO  
R
TouchFocus  
EXIT TV/VIDEO  
MENU  
VOLUME  
CHANNEL  
S-VIDEO VIDEO  
100  
0
ENT  
FAV  
PIC  
SI  
ZE  
FAVORITE  
ALS  
EXIT  
TV/VIDEO  
Video 3  
Video/audio inputs  
(behind the door)  
MENU  
DVDMENU  
MENU  
POWER  
ENTE  
R
EXIT  
FAV  
TV  
ANT-1 IN ANT-2 IN  
ANT OUT  
CBL/SAT CH  
VCR  
VOL  
DVI/HDCP IN  
DVD  
POP DIRECT CH MUTE  
SLEEP  
(
)
ANT 75  
TV/VCR PAUSE  
STOP  
PLAY  
SPLIT  
DVI/HDCP IN  
FREEZE SOURCE  
ANT-1  
OUT  
ANT-2  
REW  
FF  
SKIP/SEARCH  
CH SCAN  
REC  
SWAP  
POP CH  
LIGHT  
Back  
IN  
CT-90159  
COLOR  
STREAM  
HD-1  
COLOR  
STREAM  
HD-2  
VIDEO  
1
VIDEO  
2
Y
Y
S-VIDEO  
AUDIO  
R
L
P
B
R
PB  
OUT  
AUDIO CENTER  
CHANNEL IN  
VIDEO  
P
PR  
VIDEO  
L/  
L/  
MONO  
MONO  
L
L
AUDIO  
R
L
Audio Center  
Channel IN  
VAR  
AUDIO  
R
AUDIO  
R
AUDIO  
R
AUDIO  
ON OFF  
R
VIDEO 1/2  
ColorStream  
HD1  
Variable Audio OUT  
Audio OUT  
ColorStream  
HD2  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting your TV  
Note: Cables are not supplied with your TV.  
●
Coaxial cable is the cable that comes in from your antenna, cable TV  
service, or cable converter box. Coaxial cable uses “F” connectors.  
Coaxial (antenna) cable  
●
Standard A/V (audio/video) cables usually come in sets of three, and  
are typically color-coded according to use: yellow for video, red for  
stereo right audio, and white for stereo left (or mono) audio.  
On your TV’s back panel, the standard A/V inputs are color-coded in  
the same manner as the cables.  
Standard A/V cables (red/white/yellow)  
S-video cable  
●
S-Video cable is for use with video equipment that has an S-Video input.  
●
Component video cables come in sets of three, and are for use with  
video equipment that has component video inputs. (ColorStream® is  
Toshiba’s brand of component video.)  
●
DVI-D digital single-link cable is for use with video equipment that  
has a DVI-D digital single-link connector (see page 14).  
Component video cables  
NOTE REGARDING PICTURE QUALITY  
When connecting video equipment to your Toshiba TV:  
●
For GOOD picture quality: Use a standard yellow video cable.  
●
DVI-D digital single-link cable  
For BETTER picture quality: If your equipment has an S-video  
input, use an S-video cable instead of a standard yellow video cable.  
(You still must connect the standard red and white audio cables for full  
system connection, but do not connect the standard yellow video cable at  
the same time, or the picture performance will be unacceptable.)  
CAUTION:  
Do not plug in any power cords until you have  
finished connecting all equipment.  
●
For BEST picture quality: If your equipment has component video (or  
DVI) inputs, use either component video cables (or a DVI cable) instead  
of a standard video or S-video cable. (You still must connect the standard  
red and white audio cables for full system connection, but do not connect  
the standard yellow video cable or an S-Video cable at the same time.)  
Connecting a VCR  
This connection allows you to watch local channels and video  
programs, play or record on the VCR while watching TV, and record  
from one channel while watching another channel.  
You will need:  
• two coaxial cables  
• one set of standard A/V cables  
Note:  
From Cable Box or Antenna  
Stereo VCR  
If you have a mono VCR, connect L/Mono to  
VCR Audio OUT using only one audio cable.  
VIDEO  
AUDIO  
L
R
If you have a VCR with S-video, use an  
S-video cable (in the S-video jacks) instead of  
the standard video cable.  
IN  
OUT to TV  
IN from ANT  
CH 3  
CH 4  
OUT  
Do not connect a standard video cable and  
an S-video cable to Video-1 (or Video-2) at  
the same time, or the picture performance  
will be unacceptable.  
(
)
ANT 75  
DVI/HDCP IN  
ANT-1  
OUT  
ANT-2  
The unauthorized recording, use,  
distribution, or revision of television  
programs, videotapes, DVDs, and other  
materials is prohibited under the  
Copyright Laws of the United States and  
other countries, and may subject you to  
civil and criminal liability.  
IN  
COLOR  
STREAM  
HD-1  
COLOR  
STREAM  
HD-2  
VIDEO  
1
VIDEO  
2
Y
Y
S-VIDEO  
AUDIO  
R
L
PB  
PB  
OUT  
AUDIO CENTER  
CHANNEL IN  
VIDEO  
PR  
P
L
R
VIDEO  
L/  
L/  
MONO  
MONO  
L
L
AUDIO  
R
VAR  
AUDIO  
R
AUDIO  
R
AUDIO  
R
AUDIO  
ON OFF  
R
TV  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting a cable converter box  
This connection allows you to watch basic and premium cable channels  
.
Note:  
When you use a converter box with your TV,  
the remote control will not operate some  
features, such as programming your favorite  
channels, labeling channels, and locking  
channels.  
To watch basic cable and use the TV’s features, select ANT-1. To view  
premium channels, select ANT-2, tune the TV to channel 3 or 4  
(whichever channel is vacant in your area), and use the converter box  
to change channels.  
You will need:  
• three coaxial cables  
From Cable  
TV  
)
AN
OUT IN  
ANT-1  
OUT  
ANT-2  
Cable converter box  
IN  
COLOR  
STREAM  
HD-1  
COLOR  
STREAM  
HD-2  
VIDEO  
1
VIDEO  
2
Y
Y
S-VIDEO  
AUDIO  
R
L
P
B
R
PB  
OUT  
AUDIO CENTER  
CHANNEL IN  
VIDEO  
P
P
L
R
VIDEO  
L/  
L/  
MONO  
MONO  
L
L
AUDIO  
R
VAR  
AUDIO  
R
AUDIO  
R
AUDIO  
R
AUDIO  
ON OFF  
R
Connecting a cable converter box and VCR  
Note:  
This connection allows you to watch and record basic and premium  
cable channels, watch videotapes, and record one channel while  
watching another channel. To watch basic cable and use the TV’s  
features, select ANT-1.  
To view premium channels or record with the VCR, select ANT-2,  
tune the TV to channel 3 or 4 (whichever channel is vacant in your  
area), and use the converter box to change channels.  
If you have a mono VCR, connect L/Mono to  
VCR Audio OUT using only one audio cable.  
If you have a VCR with S-video, use an  
S-video cable (in the S-video jacks) instead  
of a standard video cable. Do not connect a  
standard video cable and an S-video cable  
to Video-1 (or Video-2) at the same time, or  
the picture performance will be unacceptable.  
You will need:  
When you use a converter box with your TV,  
the remote control will not operate some  
features, such as programming your favorite  
channels, labeling channels, and locking  
channels.  
• four coaxial cables  
• one set of A/V cables  
From Cable  
TV  
The unauthorized recording, use,  
distribution, or revision of television  
programs, videotapes, DVDs, and other  
materials is prohibited under the  
Copyright Laws of the United States and  
other countries, and may subject you to  
civil and criminal liability.  
)
AN
DVI/HDCP IN  
ANT-1  
OUT  
ANT-2  
IN  
IN  
COLOR  
STREAM  
HD-1  
COLOR  
STREAM  
HD-2  
OUT  
VIDEO  
1
VIDEO  
2
Cable converter box  
Y
Y
S-VIDEO  
AUDIO  
R
L
PB  
PB  
OUT  
AUDIO CENTER  
CHANNEL IN  
VIDEO  
PR  
PR  
VIDEO  
L/  
L/  
MONO  
MONO  
L
L
AUDIO  
R
L
VAR  
AUDIO  
R
AUDIO  
R
AUDIO  
R
AUDIO  
ON OFF  
R
L
R
R
IN  
OUT to TV  
IN from ANT  
OUT  
CH 3  
CH 4  
L
VIDEO  
AUDIO  
9
Stereo VCR  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting a DVD player or satellite receiver  
and a VCR  
Note:  
This connection allows you to watch DVD/satellite, VCR, and TV  
programs, and record one TV channel while watching another  
channel.  
For the highest possible picture quality from  
a DVD player or satellite receiver without  
component video or DVI/HDCP, use an  
S-video cable. (If your DVD player has  
component video, see page 11. If your  
satellite receiver has component video, see  
page 12. If your DVD plaer or satellite  
receiver has DVI/HDCP, see page 14.)  
You will need:  
• two coaxial cables (three if satellite receiver is used)  
• one set of standard A/V cables  
• one pair of audio cables  
• one S-video cable (between the TV and DVD player/satellite  
receiver)  
Do not connect both an S-video cable and  
a standard video cable between the TV and  
DVD player/satellite receiver at the same time  
or the picture performance will be  
unacceptable.  
Stereo VCR  
VIDEO  
AUDIO  
L
R
Do not connect the DVD player/satellite  
receiver and VCR to the same video channel  
on the TV. (See the illustrations, which show  
the DVD player/satellite receiver connected  
to Video-1 on the TV, and the VCR connected  
IN  
IN from ANT OUT to TV  
CH 3  
CH 4  
From  
Antenna  
OUT  
TV  
(
)
ANT 75  
to Video-2 on the TV.)  
DVI/HDCP IN  
ANT-1  
OUT  
ANT-2  
The unauthorized recording, use,  
distribution, or revision of television  
programs, videotapes, DVDs, and other  
materials is prohibited under the  
Copyright Laws of the United States and  
other countries, and may subject you to  
civil and criminal liability.  
IN  
COLOR  
STREAM  
HD-1  
COLOR  
STREAM  
HD-2  
VIDEO  
1
VIDEO  
2
Y
Y
S-VIDEO  
AUDIO  
R
L
P
B
PB  
OUT  
AUDIO CENTER  
CHANNEL IN  
VIDEO  
P
L
R
VIDEO  
L/  
L/  
MONO  
MONO  
L
AUDIO  
VAR  
AUDIO  
R
AUDIO  
R
AUDIO  
R
AUDIO  
ON OFF  
R
DVD Player  
AUDIO  
OUT  
L
R
S-VIDEO VIDEO  
OUT OUT  
From  
Satellite  
Dish  
Satellite Receiver  
AUDIO  
OUT  
L
IN from ANT  
R
S-VIDEO VIDEO  
OUT OUT  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting a DVD player with ColorStream®  
(component video) and a VCR  
Note:  
This connection allows you to watch DVD, VCR, and TV programs,  
and record TV programs.  
For the highest possible picture quality, use  
component video cables (or a DVI-D digital  
single-link cable) between the TV and DVD  
player.  
Your TV has ColorStream® (component video) inputs. Connecting  
your TV to a DVD player with component video inputs (such as a  
Toshiba DVD player with ColorStream®) can greatly enhance picture  
quality and realism.  
You can connect the component video cables  
to either set of the ColorStream jacks on the  
TV (HD1 or HD2).  
– To record one TV program while watching another TV program,  
tune the VCR to the channel to record, and tune the TV to the  
channel to watch.  
– To record a TV program while watching a DVD, tune the VCR to  
the channel to record, and select ColorStream HD1 on the TV (see  
“Selecting the antenna input” on page 22).  
For DVI/HDCP connection, see page 14.  
The ColorStream HD1/HD2 and DVI/HDCP  
jacks can be used with Progressive (480p,  
720p) and Interlaced (480i,1080i) scan  
systems; however, a 1080i signal will provide  
the best picture performance.  
You will need:  
If your DVD player is not compatible with  
component video or DVI/HDCP, use the  
S-video connections (plus the standard audio  
connections) instead (see page 10).  
• two coaxial cables  
• one set of A/V cables  
• one pair of audio cables  
• one set of component video cables (one S-video cable for a DVD  
player without component video inputs; see notes at right)  
The unauthorized recording, use,  
distribution, or revision of television  
programs, videotapes, DVDs, and other  
materials is prohibited under the  
Copyright Laws of the United States and  
other countries, and may subject you to  
civil and criminal liability.  
Stereo VCR  
IN from ANT OUT to TV  
VIDEO  
AUDIO  
L
From Antenna  
R
IN  
CH 3  
CH 4  
OUT  
TV  
(
)
ANT 75  
DVI/HDCP IN  
ANT-1  
OUT  
ANT-2  
IN  
COLOR  
STREAM  
HD-1  
COLOR  
STREAM  
HD-2  
VIDEO  
1
VIDEO  
2
Y
Y
S-VIDEO  
AUDIO  
R
L
PB  
PB  
OUT  
AUDIO CENTER  
VIDEO  
CHANNEL IN  
P
R
P
L
R
VIDEO  
L/  
L/  
MONO  
MONO  
L
AUDIO  
R
VAR  
AUDIO  
R
AUDIO  
R
AUDIO  
R
AUDIO  
ON OFF  
R
AUDIO  
OUT  
L
L
Y
PB  
PR  
R
R
VIDEO  
OUT  
S-VIDEO  
COMPONENT VIDEO  
DVD Player with component video  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting a DTV receiver/set-top box with  
ColorStream® (component video) and a VCR  
Note:  
This connection allows you to watch DTV (digital TV), VCR, and  
TV programs, and record DTV and TV programs.  
For the highest possible picture quality, use  
component video cables (or a DVI-D digital  
single-link cable) between the TV and DTV  
receiver/set-top box.  
Your TV has ColorStream (component video) inputs. Connecting  
your TV to a DTV receiver with component video inputs can greatly  
enhance picture quality and realism.  
You can connect component video cables to  
either set of ColorStream jacks on the TV  
(HD1 or HD2).  
– To record and watch a DTV program, select LINE IN on the  
VCR, and select ColorStream HD2 (or VIDEO 1 for a non-  
ColorStream connection) on the TV (see “Selecting the antenna  
input” on page 22).  
– To record a TV program while watching a DTV program, tune the  
VCR to the channel to record, and select ColorStream HD2 on the  
TV.  
For DVI/HDCP connection, see page 14.  
The ColorStream HD1/HD2 and DVI/HDCP  
jacks can be used with Progessive (480p,  
720p) and Interlaced (480i, 1080i) scan  
systems; however, a 1080i signal will provide  
the best picture performance.  
– To record and watch the same TV program, tune the VCR to the  
channel to record, and select VIDEO 1 on the TV.  
If your DTV receiver or set-top box is not  
compatible with component video or DVI/  
HDCP, use the S-video connections (plus the  
standard audio connections) instead (see  
page 10).  
– To record one TV program while watching another TV program,  
tune the VCR to the channel to record, and tune the TV to the  
channel to watch.  
You will need:  
• three coaxial cables  
• two sets of A/V cables  
• one pair of audio cables  
The unauthorized recording, use,  
distribution, or revision of television  
programs, videotapes, DVDs, and other  
materials is prohibited under the  
Copyright Laws of the United States and  
other countries, and may subject you to  
civil and criminal liability.  
• one set of component video cables (one S-video cable for a DTV  
receiver without component video; see notes at right)  
Stereo VCR  
IN from ANT OUT to TV  
From  
Antenna  
VIDEO  
AUDIO  
L
R
IN  
CH 3  
CH 4  
OUT  
TV  
(
)
ANT 75  
DVI/HDCP IN  
ANT-1  
OUT  
ANT-2  
IN  
COLOR  
STREAM  
HD-1  
COLOR  
STREAM  
HD-2  
VIDEO  
1
VIDEO  
2
Y
Y
S-VIDEO  
AUDIO  
R
L
PB  
PB  
OUT  
AUDIO CENTER  
O  
CHANNEL IN  
P
R
L
R
VIDEO  
L/  
L/  
MONO  
MONO  
L
L
AUDIO  
R
VAR  
AUDIO  
R
AUDIO  
AUDIO  
R
AUDIO  
ON OFF  
R
AUDIO  
OUT  
From  
DTV Antenna  
L
L
Y
P
B
PR  
Satelite IN  
R
R
IDEO  
OUT  
S-VIDEO  
COMPONENT VIDEO  
DTV Receiver with component video  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting two VCRs  
This connection allows you to record (dub/edit) from one VCR to  
another VCR while watching a videotape. You can also record from  
one TV channel while watching another TV channel.  
You will need:  
• two coaxial cables  
• two sets of A/V cables  
VCR1  
IN from ANT OUT to TV  
Note:  
VIDEO  
AUDIO  
L
R
From Antenna  
If you have VCRs with S-video, use S-video  
cables instead of standard video cables for  
better picture performance. Do not connect  
both a standard video cable and an S-video  
cable to Video-1 (or Video-2) at the same  
time, or the picture performance will be  
unacceptable.  
IN  
CH 3  
CH 4  
OUT  
TV  
(
)
ANT 75  
DVI/HDCP IN  
ANT-1  
OUT  
ANT-2  
Do not connect the same VCR to the output  
and input jacks on the TV at the same time.  
To dub or edit, VCR 2 must select Line IN,  
and the TV must select VIDEO 1 (see  
“Selecting the antenna input” on page 22).  
IN  
COLOR  
COLOR  
STREAM  
HD-2  
VIDEO  
1
VIDEO  
2
STREAM  
HD-1  
Y
PB  
PR  
L
Y
S-VIDEO  
AUDIO  
The Video OUT jack does not output the  
POP picture.  
R
L
*
PB  
PR  
L
OUT  
AUDIO CENTER  
VIDEO  
CHANNEL IN  
VIDEO  
**The Audio OUT jacks can output the sound  
L/  
L/  
MONO  
MONO  
L
of either the Main or POP picture (see  
VAR  
AUDIO  
R
AUDIO  
R
AUDIO  
R
AUDIO  
AUDIO  
ON OFF  
“Selecting the Audio OUT sound” on  
R
page 55).  
VCR2  
VIDEO  
AUDIO  
L
R
IN  
The unauthorized recording, use,  
distribution, or revision of television  
programs, videotapes, DVDs, and other  
materials is prohibited under the  
Copyright Laws of the United States and  
other countries, and may subject you to  
civil and criminal liability.  
CH 3  
CH 4  
OUT  
*
**  
Connecting a camcorder  
This connection allows you to watch video materials recorded on a  
camcorder.  
You will need:  
• one set of A/V cables  
Note:  
Camcorder  
If you have a camcorder with S-video, use an  
S-video cable instead of a standard video  
cable for better picture performance. Do not  
connect both a standard video cable and an  
S-video cable at the same time, or the picture  
performance will be unacceptable.  
VIDEO AUDIO  
OUT  
L
R
L/MONO  
AUDIO  
R
S-VIDEO VIDEO  
Video-3 (front panel)  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting a device to the DVI/HDCP1 input  
The DVI/HDCP input on your TV is designed to accept HDCP  
program material in digital form from EIA/CEA-861–compliant2  
consumer electronic devices, such as a set-top box or DVD player  
equipped with a DVI-D digital single-link output connection.3  
Notes:  
1
DVI/HDCP = Digital Visual Interface/  
High-bandwidth Digital Content Protection.  
EIA/CEA-861 compliance covers the  
2
transmission of uncompressed digital  
video with high-bandwidth digital content  
protection, which is being standardized for  
future reception of high-definition video  
signals.  
Consult your consumer electronics dealer  
for availability.  
The DVI/HDCP input is designed for best performance with 1080i  
high-definition video signals. The DVI/HDCP input also will accept  
and display 480p, 720p, and 480i picture signals.  
Note: This TV is not intended for connection to  
and should not be used with a PC (personal  
computer).  
3
You will need:  
• one coaxial cable  
• one DVI-D digital single-link cable  
Caution:  
To ensure that the DVI/HDCP device is reset  
properly, it is recommended that you follow  
these procedures:  
• When turning on your electronic  
components, turn on the TV first,  
and then the DVI/HDCP device.  
• When turning off your electronic  
components, turn off the DVI/HDCP  
device first, and then the TV.  
Note: For proper operation, the DVI-D cable length  
should not exceed 3m (9.8 ft). The recommended  
length is 2m (6.6 ft).  
• one pair of standard audio cables  
DVI/HDCP device  
(for example, set-top box or DVD player)  
DVI/HDCP  
OUT  
VIDEO  
AUDIO  
L
R
IN  
OUT  
TV  
From  
Antenna  
or Cable  
(
)
ANT 75  
DVI/HDCP IN  
ANT-1  
OUT  
ANT-2  
IN  
COLOR  
STREAM  
HD-1  
COLOR  
STREAM  
HD-2  
VIDEO  
1
VIDEO  
2
Y
Y
S-VIDEO  
AUDIO  
R
L
PB  
PR  
PB  
PR  
L
OUT  
AUDIO CENTER  
CHANNEL IN  
VIDEO  
VIDEO  
L/  
L/  
MONO  
MONO  
L
L
AUDIO  
R
VAR  
AUDIO  
R
AUDIO  
R
AUDIO  
R
AUDIO  
ON OFF  
R
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting an audio system  
Amplifier  
This connection allows you to use an audio amplifier to adjust the  
audio level. This also allows you to use external speakers.  
LINE IN  
L
R
To control the audio, turn on the TV and the stereo amplifier, and  
turn off the built-in speakers (see “Turning off the built-in speakers”  
on page 55).  
TV  
(
)
ANT 75  
DVI/HDCP IN  
ANT-1  
OUT  
ANT-2  
You will need:  
• one pair of audio cables  
Note:  
IN  
COLOR  
STREAM  
HD-1  
COLOR  
To hear sound when using an external audio amplifier, the  
volume of both the TV and the amplifier must be set  
above 0 (zero).  
VIDEO  
1
VIDEO  
2
STREAM  
HD-2  
Y
PB  
PR  
L
Y
S-VIDEO  
AUDIO  
R
L
PB  
PR  
L
OUT  
AUDIO CENTER  
CHANNEL IN  
VIDEO  
VIDEO  
L/  
L/  
For example, if the volume of the TV is set to 0, you will  
not be able to hear any sound, even the volume of the  
amplifier is at its highest level.  
MONO  
MONO  
L
VAR  
AUDIO  
R
AUDIO  
R
AUDIO  
R
AUDIO  
R
AUDIO  
ON OFF  
R
Connecting an A/V receiver  
This connection allows you to use an audio/video (A/V) receiver to  
enhance your TV’s sound.  
If you have a system with Dolby Pro Logic® surround sound, you can  
add to the realism of the sound by using the TV’s internal speakers as  
center channel speakers.  
Caution:  
To avoid damaging the TV speakers:  
• Turn off the TV before connecting or  
disconnecting the Audio Center Channel  
cable.  
• Do not connect from the A/V receiver’s  
Center Speaker OUT (amplified signal) to  
the TV’s Audio Center Channel IN.  
You will need:  
• one set of A/V cables  
• one single audio cable for the audio center channel  
To A/V Receiver  
From  
From  
Center OUT  
To TV IN  
Dolby Pro Logic* surround sound  
system connection example  
Video OUT  
TV  
(
)
ANT 75  
DVI/HDCP IN  
ANT-1  
OUT  
ANT-2  
Audio  
Video  
Video  
Audio  
VCR  
LDP/DVD  
IN  
COLOR  
STREAM  
HD-1  
COLOR  
STREAM  
HD-2  
VIDEO  
1
VIDEO  
2
Y
Y
S-VIDEO  
AUDIO  
A/V receiver  
R
L
PB  
PB  
OUT  
UDIO CENTER  
CHANNEL IN  
VIDEO  
P
R
P
L
R
VIDEO  
L/  
L/  
ON  
OFF  
MONO  
MONO  
L
L
AUDIO  
R
VAR  
AUDIO  
R
AUDIO  
AUDIO  
R
AUDIO  
ON OFF  
R
T V  
Left  
speaker  
Right  
speaker  
Note:  
Refer to the instructions provided with your A/V receiver  
for details about your surround sound system.  
When the Audio Center Channel ON/OFF switch is in  
the ON position, the TV speakers will function only as  
center channel speakers. At this time, the SBS feature  
should be set OFF. See page 54.  
Surround  
speaker L  
Surround  
speaker R  
Adjust the volume for the center channel speakers  
using the center level control on the A/V receiver.  
_________  
To use the TV speakers as normal speakers, set the  
Audio Center Channel ON/OFF switch to the OFF  
position.  
* Dolby Pro Logic is a registered trademark  
of Dolby Laboratories Licensing  
Corporation.  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the remote control  
Preparing the remote control for use  
Your TV remote control can operate your TV and most cable  
converter boxes, satellite receivers, VCRs, DVD players, and HTIBs  
(home theater in a box), even if they are different brands.  
If you have a Toshiba device:  
Your TV remote control is preprogrammed to operate most Toshiba  
devices. See page 19.  
If you have a non-Toshiba device or a Toshiba device  
that the remote control is not preprogrammed to  
operate:  
You can program the TV remote control so it will operate the other  
device. See pages 17–19.  
Installing the remote control batteries  
1. Remove the battery cover from the back of the remote control.  
Caution:  
• Dispose of batteries in a designated  
disposal area. Do not throw batteries into a  
fire.  
• Do not mix battery types or combine used  
batteries with new ones.  
Squeeze tab and  
lift cover.  
• If the remote control does not operate  
correctly, or if the operating range becomes  
reduced, replace both batteries with new  
ones.  
2. Install two “AA” size batteries, making sure to match the + and –  
signs on the batteries to the signs on the battery compartment.  
• If the batteries are dead or if you will not  
use the remote control for a long time,  
remove the batteries to prevent battery acid  
from leaking into the battery compartment.  
Note:  
If your Toshiba TV remote control does not  
operate all the features of your other device,  
use the original remote control for that device.  
3. Reinsert the battery cover in the remote control until the tab  
snaps.  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Programming the remote control to operate a  
cable converter box, satellite receiver, VCR,  
DVD player, or HTIB (home theater in a box)  
Your Toshiba TV remote control is preprogrammed to operate most  
Toshiba devices. To program your TV remote control to operate a  
non-Toshiba device (or a Toshiba device that it is not preprogrammed  
to operate), follow the steps below. For details on using the remote  
control to operate the device, see page 19.  
RECALL  
POWER  
POWER  
RECALL  
INFO  
TV/VIDEO  
1
4
2
5
8
3
6
Channel  
Number  
9
CHRTN  
7
+10  
100  
0
ENT  
FAV  
PIC SIZE  
1. In the remote control code table (below and on the next page),  
find the code for your device. If more than one code is listed, try  
each one separately until you find one that works.  
FAVORITE  
MENU  
DVDMENU  
ENTER  
2. Set the Device Switch to the type of device you are programming  
the remote control to operate — CBL/SAT (for a cable converter  
box or satellite receiver), VCR (for a VCR or TV/VCR combo),  
or DVD (for a DVD player or HTIB [home theater in a box]).  
N
EXIT  
C
FAV  
TV  
Device Switch  
CBL/SAT CH  
VCR  
VOL  
DVD  
3. While holding down RECALL, press the Channel Number  
buttons to enter the 3-digit code for your device.  
Note:  
4. To test the code, turn on the device, point the remote control at  
• In addition to POWER, confirm that all  
necessary keys on the TV remote control  
operate your device. If some keys are not  
operational, repeat the device code setup  
using another code (if other codes are listed  
for your device). If, after trying all listed  
codes, the necessary keys do not operate  
your device, use the device’s original remote  
control.  
it, and press POWER. See notes at right.  
• If the correct code was entered, the device will turn off.  
• If the device does not respond, repeat steps 1 – 4 using  
another code.  
• If the device does not respond to another code, you will need  
to use the remote control that came with the device.  
5. Remember to set the Device Switch back to TV to control the TV.  
• Every time you change the batteries, you will  
need to reprogram the remote control.  
6. For future reference, write down the code(s) you used:  
DEVICE  
CODE  
DEVICE  
CODE  
• Some newer VCRs respond to either of two  
codes. These VCRs have a switch labeled  
“VCR1/VCR2.” If your VCR has this kind of  
switch and does not respond to the codes  
for your VCR brand, set the switch to the  
other position (“VCR1” or “VCR2”) and  
reprogram the remote control.  
Remote control codes  
In some cases you may not be able to operate your device with the TV remote control. Your other device may use  
a code that is not recognized by the TV remote control. If this happens, use the device’s remote control.  
Hamlin: 093  
Hitachi: 062, 095, 096  
Jasco: 097  
RCA: 064, 081  
Realistic: 065  
Recoton: 102  
Samsung: 077, 090  
Scientific Atlanta: 063,  
078, 079, 080, 088,  
098, 101, 105  
Sears: 095  
Signature: 062  
Signature 2000: 096  
Sprucer: 081, 085  
Starcom: 069, 082, 087,  
096, 103, 104  
Stargate: 069, 090  
Sylvania: 095, 100  
TeleView: 090  
U. S. Electronics: 087,  
096, 098  
United Cable: 082  
Universal: 065, 092, 097,  
099, 102, 103  
General Instruments:  
010, 011, 012, 022,  
023, 031, 049  
Hitachi: 033  
Hughes: 033  
Hughes Network  
Systems: 019  
Cable converter  
box  
ABC: 061, 062, 063,  
082, 084, 087, 091,  
092, 096, 098  
Archer: 065, 092, 097,  
099  
Cableview: 064, 094  
Century: 092  
Citizen: 090, 092, 097  
Contec: 083, 085, 086,  
088, 093, 098  
Diamond: 093  
Eagle: 091  
GE: 061, 062  
Gemini: 069, 070, 094  
General Instruments:  
062, 089, 096  
Jerrold: 062, 069, 071,  
082, 086, 089, 091,  
096  
Magnavox: 072, 096  
Memorex: 091, 092, 104  
Multi Canal: 090  
Novavision: 101  
Panasonic: 081, 083, 085  
Philco: 087  
Philips: 066, 067, 068,  
070, 072, 073, 074,  
075, 091, 092  
Pioneer: 076, 077  
Proscan: 061, 062  
Radio Shack: 092, 097,  
099  
Wards: 096  
Intersat: 048  
Janeil: 027  
Satellite receiver  
Alphastar: 038, 059  
Chaparral: 034  
DISH Network: 057  
Drake: 020, 040, 044,  
046, 050, 053  
Echostar: 018, 041, 051  
Express Vu: 057  
Fujitsu: 027  
JVC: 017, 057  
Kenwood: 029  
Magnavox: 060  
Optimus: 058  
Pansat: 036, 052  
Primestar: 015, 042  
Proscan: 008, 009, 013  
Radio Shack: 022, 023,  
030  
Texscan: 100  
Tocom: 071, 084, 085  
GE: 008, 009, 013  
(Continued)  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Remote control codes (cont.)  
Hitachi: 005, 032, 033,  
034, 035  
JVC: 003, 007, 036,  
Colortyme: 005  
Craig: 009, 010, 016,  
061, 065, 079  
Curtis Mathes: 001, 005,  
009, 012, 014, 040,  
048, 053, 056, 057  
Daewoo: 011, 013, 015,  
017, 018, 019, 057,  
078  
Daytron: 078  
Denon: 063  
Dimensia: 001, 048  
Electrohome: 010, 020,  
065  
Emerson: 003, 008, 010,  
011, 017, 018, 020,  
028, 039, 054, 057,  
062, 065, 068, 072  
Fisher: 007, 016, 021,  
022, 023, 057, 064,  
068, 070, 071, 079  
Fuji: 004, 041  
Memorex: 007, 009,  
010, 016, 018, 034,  
049, 063, 065, 066,  
068, 075, 079  
MGA: 020, 028, 039  
MGN: 056  
Minolta: 024, 025, 035,  
063  
Mitsubishi: 020, 024,  
025, 028, 039, 043,  
065  
Sanyo: 007, 009, 016,  
054, 064, 068, 071,  
075, 079, 085  
Scott: 008, 011, 017,  
028, 030, 057, 065,  
072  
Sears: 007, 010, 016,  
021, 022, 023, 024,  
025, 035, 053, 057,  
063, 064, 065, 068,  
071, 075, 079  
Sharp: 013, 020, 031,  
049, 051, 060, 066  
Shintom: 004, 025, 032,  
061  
Satellite receiver  
(cont.)  
RCA: 008, 009, 013, 016  
042, 088  
Realistic: 030  
Kenwood: 037  
Samsung: 059  
Sony: 014, 055  
Star Choice: 057  
Konka: 008, 009  
Magnavox: 004, 038  
Memorex: 039  
Star Trak: 025, 026, 037,  
Mintek: 040  
054  
STS: 024  
Toshiba: 000, 001, 002,  
NAD: 026  
Nakamichi: 041  
Norcent: 043  
Montgomery Ward: 049  
Motorola: 049  
003, 004, 005, 006,  
Onkyo: 044  
007, 020, 031, 056  
Oritron: 058  
MTC: 009, 046, 061  
Multitech: 009, 012, 018  
NEC: 005, 006, 007,  
012, 014, 037, 043,  
053, 054, 067, 070  
Nikko: 010  
Noblex: 009  
Optimus: 010, 049, 065  
Optonica: 031  
Orion: 054, 057, 062,  
065, 068, 072  
Panasonic: 036, 045,  
046, 057, 061, 072,  
079  
Pentax: 012, 024, 025,  
035, 042, 053, 063  
Pentex Research: 014  
Philco: 026, 027, 063  
Philips: 026, 031, 044,  
057  
Pioneer: 006, 024, 043,  
055  
Portland: 012, 013, 015  
Proscan: 001, 002, 048  
Proton: 061  
Quasar: 045  
Radio Shack: 010, 031,  
065  
Radio Shack/Realistic:  
007, 009, 010, 016,  
018, 020, 021, 022,  
031, 049  
Uniden: 021, 028, 030,  
Panasonic: 010, 045,  
032, 035, 039, 043,  
046, 047, 048, 049,  
Signature: 049  
045, 047, 058  
Zenith: 027  
050  
Signature 2000: 075  
Singer: 047, 061  
Sony: 004, 032, 033,  
041, 052, 058, 070,  
074, 076, 077, 080  
STS: 035  
Sylvania: 018, 026, 027,  
028, 044, 072  
Symphonic: 018, 050,  
051, 053, 073, 079  
Tandy: 007  
Tashiko: 010  
Tatung: 037  
Teac: 018, 029, 037  
Technics: 036  
Teknika: 010, 018, 065  
Toshiba: 000, 011, 021,  
023, 024, 028, 030,  
039, 057, 074, 078,  
079  
Totevision: 009, 010,  
065  
Unitec: 073  
Philips: 004, 051  
Pioneer: 052, 053, 054,  
TV/VCR Combo  
055  
Proscan: 001, 056  
Qwestar: 057, 058  
RCA: 001, 002, 059, 089 Funai: 018, 073  
Sampo: 060  
Samsung: 061, 062, 086,  
090  
Action: 078  
GE: 059, 062  
Goldstar: 065  
Panasonic: 065  
Precision: 078  
Quasar: 065  
Realistic: 079  
Sony: 074  
Garrard: 018  
GE: 001, 002, 009, 040,  
042, 048, 056  
Go Video: 056, 059,  
061, 081  
Goldstar: 005, 010, 014,  
054, 056, 065, 067  
Gradiente: 018, 065  
Harman Kardon: 005  
Hitachi: 024, 025, 035,  
037, 042, 063, 070,  
080  
Sansui: 073  
Sanyo: 063, 091  
Sharp: 064, 067  
Sherwood: 074  
Sony: 011, 012, 065,  
066, 068, 069, 070  
Sylvania: 027  
Toshiba: 057  
Zenith: 065  
DVD/VCR Combo  
Go Video:  
DVD=087, VCR=081  
JVC:  
DVD=088, VCR=082  
RCA:  
DVD=089, VCR=083  
Samsung:  
DVD=090, VCR=084  
Sanyo:  
DVD=091, VCR=085  
Zenith:  
Teac: 071  
Technics: 072  
Techwood: 075  
Toshiba: 000, 013, 076,  
077, 078  
Yamaha: 079, 080, 081  
Zenith: 014, 082, 092  
JBL: 076  
JC Penney: 005, 006,  
007, 008, 009, 010,  
023, 024, 025, 026,  
035, 056, 061, 063,  
065  
Unitech: 009  
Vector Research: 005,  
006, 011, 012, 053  
Video Concepts: 005,  
006, 011, 012, 039,  
053  
Wards: 009, 010, 011,  
016, 018, 020, 024,  
025, 031, 035, 049,  
051, 056, 057, 060,  
065, 066, 079  
White Westinghouse:  
073  
XR-1000: 018  
Yamaha: 005, 006, 007,  
014, 037, 053  
Zenith: 004, 032, 034,  
041, 047, 069, 086  
Jensen: 024, 025, 037,  
050  
Portable DVD player  
Aiwa: 093  
Audiovox: 094, 095  
Panasonic: 024, 096, 099  
RCA: 098  
JVC: 005, 006, 007,  
014, 037, 043, 050,  
062, 063, 068, 082  
Kenwood: 005, 006,  
007, 012, 014, 037,  
043, 050, 053, 068,  
071  
Kodak: 010  
LG: 010  
Lloyds: 053, 073, 079  
Logik: 061  
LXI: 010  
Magnasonic: 061, 065,  
078  
Magnavox: 026, 027,  
034, 044, 057, 061,  
072  
Marantz: 005, 006, 007,  
012, 014, 026, 053,  
067  
DVD=092, VCR=086  
Radix: 010  
DVD player  
RCA: 001, 002, 003,  
009, 024, 025, 029,  
035, 040, 042, 045,  
048, 055, 056, 063,  
071, 083  
Realistic: 007, 009, 010,  
011, 016, 018, 020,  
021, 022, 031, 049,  
051, 056, 060, 065,  
075, 079  
Ricoh: 047  
Runco: 034  
Samsung: 009, 011, 038,  
056, 073, 084  
Sansui: 006, 037, 043,  
061  
Aiwa: 006, 015  
Apex: 016, 017  
BOSE: 097  
Broksonic: 018  
Clarion: 019  
Classic: 020  
Daewoo: 021  
Denon: 022, 023, 024,  
025  
Emerson: 026, 027  
Fisher: 028  
VCR  
Admiral: 049  
Aiko: 019  
Aiwa: 018  
Akai: 003, 004, 037,  
038, 039, 058, 069  
Audiovox: 010  
Bell & Howell: 007, 068  
Broksonic: 008, 017  
Calix: 010  
Carver: 026  
CCE: 019  
Citizen: 009, 010, 011,  
012, 013, 014, 015,  
019, 057, 073  
Funai: 027  
HTIB  
GE: 001, 029, 030  
Go Video: 087  
GPX: 031  
Lasonic: 083  
Panasonic: 084  
Venturer: 085  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the remote control to operate a cable  
converter box, satellite receiver, VCR, DVD  
player, or HTIB (home theater in a box)  
If you have a non-Toshiba device or a Toshiba device that the remote  
control is not preprogrammed to operate, you must first program the  
remote control to recognize the device (if you have not already done  
so). See pages 17 and 18.  
Note:  
Even after the TV remote control is  
programmed, it may not operate certain  
features on your other device. If this happens  
and you wish to use those features, you will  
need to use the device’s original remote  
control.  
To use your TV remote control to operate a:  
• cable converter box or satellite receiver, set the Device Switch to  
CBL/SAT.  
• VCR, set the Device Switch to VCR.  
• DVD player or HTIB, set the Device Switch to DVD.  
Point the remote control  
directly at the device.  
POWER  
RECALL  
INFO  
TV / VIDEO  
POWER  
Turns the selected device on and off.  
INFO (CBL/SAT only)  
Displays on-screen information.  
1
4
2
5
8
3
6
Channel Numbers (0-9)  
Press to directly access channels (as  
opposed to CH y z).  
9
CHRTN  
7
+10  
+10 (DVD only)  
Press to directly access  
100  
0
ENT  
DVD chapters higher than 10.  
FAV  
PI  
C
S
GUIDE (CBL/SAT only)  
I
ZE  
Displays channel guide.  
TOP MENU (DVD only)  
Accesses a DVD’s top menu.  
MENU  
DVDMENU  
y z x • (DVD only)  
Press to navigate DVD menus (may not  
ENTER  
Required by some VCRs and cable  
converter boxes to change the channel.  
work on some DVD players).  
CLEAR (DVD only)  
Press to reset the title and chapter  
number.  
EXIT  
FAV  
Device Switch  
Set to “TV” to control the TV; “CBL/SAT” to  
control a cable converter box or satellite  
receiver; “VCR” to control a VCR; “DVD”  
to control a DVD player or HTIB.  
TV  
CBL/SAT CH  
VCR  
VOL  
CH y z  
DVD  
y selects the next higher channel;  
z selects the next lower channel.  
POP DIRECT CH MUTE  
SLEEP  
PAUSE  
Press during play or record mode to  
pause the picture; press again to restart.  
TV/VCR PAUSE  
STOP  
PLAY  
SPLIT  
PLAY  
FREEZE SOURCE  
TV/VCR (VCR only)  
To view one program while recording  
another, press to select TV mode.  
Begins playback of a tape or DVD.  
REW  
FF  
SKIP/SEARCH  
STOP  
CH SCAN  
REC  
SWAP  
POP CH  
LIGHT  
Stops the tape or DVD.  
REW  
Rewinds the tape or DVD. (Press during play mode  
to view the picture moving rapidly backward.)  
SKIP/SEARCH  
Skips forward to locate later DVD  
(DVD only)  
chapters.  
REC (VCR only)  
Starts tape recording.  
CT-90159  
SKIP/SEARCH  
Skips back to beginning of current DVD  
chapter or locates previous chapters.  
(DVD only)  
FF  
Fast-forwards the tape or DVD.  
(Press during play mode to view the  
picture moving rapidly forward.)  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Learning about the remote control  
The buttons used for operating the TV only are described here.  
POWER turns the TV on and off  
POWER  
RECALL  
INFO  
TV / VIDEO  
RECALL displays screen information (page 56)  
SLEEP sets the TV to turn off at a specific time (page 50)  
TV/VIDEO selects video input source (page 48)  
MUTE mutes the sound (page 52)  
1
4
2
5
8
3
6
9
CHRTN  
7
Device Switch switches between TV, CLB/SAT/VCR, and DVD (Pages 17-19)  
+10  
Set to “TV” to control the TV.  
100  
0
ENT  
CH (channel) y z cycles through programmed channels (page 25)  
Channel Numbers (0-9, 100) allow direct access to channels (page 25)  
VOL (volume) y z adjusts the volume level  
FAV  
PIC SIZE  
MENU  
DVDMENU  
CH RTN returns to the memorized channel (page 27)  
MENU allows access to on-screen programming menus (page 21)  
ENTER sets programmed menu information (page 21)  
y z x • select or adjust programming menus (page 21)  
POP CH y z selects the POP (picture-out-picture) channel (page 34)  
FAV y z cycles through favorite channels (page 28)  
T
EXI  
FAV  
TV  
CBL/SAT CH  
VCR  
VOL  
DVD  
POP DIRECT CH MUTE  
SLEEP  
TV/VCR PAUSE  
STOP  
PLAY  
SPLIT  
FAVORITE allows access to the favorite channel search function (page  
FREEZE SOURCE  
FF  
37)  
REW  
SKIP/SEARCH  
CH SCAN  
REC  
SWAP  
POP CH  
LIGHT  
PIC SIZE cycles through the five picture sizes: Natural, Theater Wide  
1, 2, 3, and Full (page 30)  
EXIT exits programming menus (page 21)  
SPLIT turns the POP feature on and off (page 34)  
SOURCE selects the POP picture source (page 34)  
FREEZE freezes the POP picture (page 35)  
SWAP switches the main and POP pictures (page 35)  
POP DIRECT CH allows direct access to POP channels (page 34)  
CH SCAN allows access to the programmed channel search function (page 36)  
LIGHT illuminates the keypad for five seconds  
Note:  
The error message “Not Available” will appear  
if you press a key for a function that is not  
available.  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting up your TV  
Learning about the menu system  
Note regarding  
After you have installed the batteries and programmed the remote  
control, you will need to set some preferences on the TV using the  
menu system. You can access the menu using the buttons on your TV  
or remote control.  
1. Press MENU to display the menu system.  
2. Press x or • to select menu.  
Quick Connect Guide  
The Quick Connect Guide  
automatically appears on-screen the  
first time the TV is turned on. This  
feature provides on-screen  
instructions to guide you through  
initial setup of your TV.  
3. Press y or z select an item.  
4. Press x or • to select or adjust a setting.  
To stop the Quick Connect Guide,  
either press EXIT or turn off the TV.  
See page 24 for details.  
P I CTURE ANTENNA  
MODE  
SPORTS  
CONTRAST  
BR IGHTNESS  
COLOR  
1 0 0  
5 0  
5 0  
T I NT  
SHARPNESS  
RESET  
SAVE NEW PRE
x •zy  
P I CTURE ANTENNA  
E
ALS  
: SELECT  
MODE  
SPORTS  
TV front panel  
FLESH TONE  
CableClear DNR  
COLOR  
ON/ OFF  
OFF  
F I LM  
TEMPERATURE  
DISPLAY FORM
CONVERGENCE  
SAVE NEW PRE
: MOVE  
AUDI O  
TouchFocus  
MENU  
VOLUME  
CHANNEL  
EXIT TV/VIDEO  
MTS  
BASS  
TREBLE  
BALANCE  
RESET  
STEREO  
50  
50  
0
MENU  
EXIT  
: SELECT  
E
AUDI O  
SBS  
ON/ OFF  
5 0  
ON  
SBS LEVEL  
SPEAKERS  
AUDI O OUT  
MAI N  
STABLE SOUND ON  
POWER  
RECALL  
INFO  
TV/VIDEO  
: MOVE  
: SELECT  
1
4
7
2
5
8
3
6
9
CHRTN  
THEATER  
WOW  
+10  
SRS 3D  
FOCUS  
T r u B a s s  
P I CTURE S I ZE  
AUTO ASPECT  
P I CTURE SCRO
C I NEMA MODE  
ON  
ON  
100  
0
ENT  
FAV  
PIC  
SI  
ORITE  
ZE  
FAV  
SET UP  
: SELECT  
LANGUAGE  
CLOCK SET  
ANT1 / 2  
ENGL I SH  
0 0 : 0 0  
ANT1  
CABLE  
MENU  
yzx •  
MENU  
DVDMENU  
TV / CABLE  
CH PROGRAM  
ADD / ERASE  
QU I CK CONNECT  
ADD  
ENTER  
EXIT  
EXIT  
: SELECT  
FAV  
CUSTOM  
T I MER  
ON  
SLEEP  
CC  
0 0 h 0 0 m  
0 h 0 0 m  
OFF  
TV  
CBL/SAT CH  
VCR  
VOL  
ENTER  
FAVOR I TE CH1  
FAVOR I TE CH2  
CH LABEL I NG  
DVD  
V I  
LABEL  
DEO  
BACKGROUND  
POP DIRECT CH MUTE  
SLEEP  
: SELECT  
E
TV/VCR PAUSE  
STOP  
PLAY  
SPLIT  
LOCKS  
V–CH I P  
ENABLE BLOCK I NG OFF  
TV RAT I NG  
FREEZE SOURCE  
REW  
FF  
SKIP/SEARCH  
MPAA RAT I NG  
BLOCK I NG OPT I ON  
CH LOCK  
CH SCAN  
REC  
SWAP  
POP CH  
LIGHT  
V I DEO LOCK  
OFF  
OFF  
OFF  
GAME TIMER  
FRONT PANEL LOCK  
NEW P I N CODE  
: SELECT  
EXIT : END  
• Press ENTER to activate the function settings in the menus.  
• The main menu display will disappear automatically if you do  
not make a selection within 15 seconds. If you want to close all  
the on-screen displays instantly, press EXIT.  
Note:  
You can change the background of the  
menu. See page 56 for details.  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Changing the on-screen display language  
x •zy  
TV front panel  
You can choose from three different languages (English, French and  
Spanish) for the on-screen display of adjustment menus and messages.  
To select a language:  
1. Press MENU, and then press x or • until the SET UP menu  
appears.  
TouchFocus  
MENU  
VOLUME  
CHANNEL  
EXIT TV/VIDEO  
2. Press y or z to highlight LANGUAGE.  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
1
2
3
4
5
6
7
1
2
3
4
5
6
7
MENU  
SET UP  
8
9
8
9
LANGUAGE ENGL I SH  
CLOCK SET  
ANT1 / 2  
/
FRANCA I S  
0 0 : 0 0  
ANT1  
/
ESPANOL  
10  
11  
12  
13  
14  
15  
16  
17  
18  
10  
11  
12  
13  
14  
15  
16  
17  
18  
TV / CABLE  
CABLE  
CH PROGRAM  
ADD / ERASE  
QU I C K CONNECT GU I DE  
ADD  
POWER  
RECALL  
INFO  
TV/VIDEO  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
TV/VIDEO  
1
4
7
2
5
8
3
6
3. Press x or • to highlight your desired language.  
9
CHRTN  
Selecting the antenna input  
You can connect to two different antenna input sources (ANT 1 or  
ANT 2).  
+10  
100  
0
ENT  
FAV  
PIC SIZE  
FAVORITE  
To select the antenna input using the menu system:  
MENU  
yzx •  
MENU  
DVDMENU  
1. Press MENU, and then press x or • to highlight the SET UP  
menu.  
ENTER  
EXIT  
FAV  
2. Press y or z to highlight ANT 1/2.  
TV  
CBL/SAT CH  
VCR  
VOL  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
1
2
3
4
5
6
7
1
2
3
4
5
6
7
DVD  
SET UP  
8
9
8
9
LANGUAGE  
CLOCK SET  
ANT1 / 2  
ENGL I SH  
0 0 : 0 0  
ANT1 / ANT2  
CABLE  
10  
11  
12  
13  
14  
15  
16  
17  
18  
10  
11  
12  
13  
14  
15  
16  
17  
18  
TV / CABLE  
CH PROGRAM  
ADD / ERASE  
ADD  
QU I C K CONNECT GU I DE  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
3. Press x or • to highlight either ANT 1 or ANT 2, depending on  
the antenna terminal you wish to use.  
To select the antenna input using the TV/VIDEO button:  
1. Press the TV/VIDEO button on the remote control or TV (see  
illustrations below). The current signal source displays in purple.  
TV front panel  
2. Continue pressing the TV/VIDEO button to select ANT 1 or  
ANT 2.  
TouchFocus  
MENU  
VOLUME  
CHANNEL  
EXIT TV/VIDEO  
SOURCE SELECT ION  
SOURCE SELECT ION  
ANT  
1
0 : ANT  
1 : V IDEO  
2 : V IDEO  
V IDEO  
1
V IDEO  
V IDEO  
V IDEO  
1
2
3
1
2
3
TV/VIDEO  
3 :  
Col orSt ream HD1  
Col orSt ream HD2  
DVI  
4 : Col orSt ream HD1  
5 : Col orSt ream HD2  
:
:
6
7
DVI  
ANT  
ANT  
2
2
:
TV / V I DEO TO SELECT  
0
7 : TO SELECT  
Please note the following regarding  
the DVI source selection:  
Pressing TV/VIDEO on the remote  
control displays the current signal  
source (press TV/VIDEO again or 0-7  
to change)  
Pressing TV/VIDEO on the TV changes  
the current signal source  
This TV is not intended for connection  
to and should not be used with a PC  
(personal computer). See “Connecting  
a device to the DVI/HDCP input” on  
page 14 for details.  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Adding channels to the TV’s memory  
Note:  
When you press Channel y or z, your TV will stop only on the  
To tune the TV to a channel not programmed  
in the channel memory, you must use the  
Channel Number buttons on the remote  
control.  
channels stored in the TV’s channel memory.  
Follow the steps below and on the next page to program all active  
channels into the TV’s memory.  
Programming channels automatically  
Your TV can automatically detect all active channels in your area and  
store them in its memory. After the channels are stored automatically,  
you can manually add or erase individual channels (see page 24).  
To program channels automatically:  
1. Press MENU, and then press x or • until the SET UP menu  
POWER  
RECALL  
INFO  
TV/VIDEO  
appears.  
2. Press y or z until the TV/CABLE is highlighted.  
1
4
2
5
8
3
6
3. Press x or • to highlight either TV or CABLE, depending on  
which you use. If you use an antenna, highlight TV; if you use  
cable, highlight CABLE.  
9
CHRTN  
7
+10  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
100  
0
ENT  
1
2
3
4
5
6
7
1
2
3
4
5
6
7
FAV  
PIC SIZE  
FAVORITE  
SET UP  
8
9
8
9
MENU  
yzx •  
MENU  
DVDMENU  
LANGUAGE  
CLOCK SET  
ANT1 / 2  
ENGL I SH  
0 0 : 0 0  
ANT1  
10  
11  
12  
13  
14  
15  
16  
17  
18  
10  
11  
12  
13  
14  
15  
16  
17  
18  
TV / CABLE  
CH PROGRAM  
ADD / ERASE  
TV / CABLE  
ENTER  
ADD  
QU I C K CONNECT GU I DE  
EXIT  
FAV  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
TV  
Channel yz  
CBL/SAT CH  
VCR  
DVD  
VOL  
4. Press z to select CH PROGRAM.  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
1
2
3
4
5
6
7
1
2
3
4
5
6
7
SET UP  
8
9
8
9
LANGUAGE  
CLOCK SET  
ANT1 / 2  
ENGL I SH  
0 0 : 0 0  
ANT1  
10  
11  
12  
13  
14  
15  
16  
17  
18  
10  
11  
12  
13  
14  
15  
16  
17  
18  
TV / CABLE  
CH PROGRAM  
ADD / ERASE  
CABLE  
ADD  
QU I C K CONNECT GU I DE  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
5. Press x or • to start channel programming. The TV will  
automatically cycle through all the TV or Cable channels  
(depending on which you selected), and store all active channels  
in the channel memory.  
While the TV is cycling through the channels, the message  
“Programming Now—Please Wait” appears.  
6. When channel programming is complete, the message  
“Completed” appears.  
7. Press Channel y or z to view the programmed channels.  
Adding and erasing channels manually  
After you have programmed the channels automatically, you can  
manually add or erase specific channels.  
To add or erase channels:  
1. Select the channel you want to add or erase. If you are adding a  
channel, you must select the channel using the Channel Number  
buttons.  
2. Press MENU, and then press x or • until the SET UP menu  
appears.  
(continued on next page)  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3. Press y or z to highlight ADD/ERASE.  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
1
2
3
4
5
6
7
1
2
3
4
5
6
7
x •zy  
TV front panel  
SET UP  
8
9
8
9
LANGUAGE  
CLOCK SET  
ANT1 / 2  
ENGL I SH  
0 0 : 0 0  
ANT1  
10  
11  
12  
13  
14  
15  
16  
17  
18  
10  
11  
12  
13  
14  
15  
16  
17  
18  
TV / CABLE  
CH PROGRAM  
ADD / ERASE  
CABLE  
ADD / ERASE  
QU I C K CONNECT GU I DE  
TouchFocus  
EXIT TV/VIDEO  
MENU  
VOLUME  
CHANNEL  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
MENU  
4. Press x or • to select ADD or ERASE, depending on the  
function you want to perform.  
5. Repeat steps 1-4 for other channels you want to add or erase.  
POWER  
RECALL  
INFO  
TV/VIDEO  
Using the Quick Connect Guide  
The Quick Connect Guide automatically starts the first time the TV  
is turned on.  
You can change the current settings any time.  
1
4
7
2
5
8
3
6
9
CHRTN  
1. Press MENU, and then press x or • until the SET UP menu  
+10  
100  
0
ENT  
appears.  
FAV  
PIC SIZE  
2. Press y or z to highlight “QUICK CONNECT GUIDE.”  
FAVORITE  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
MENU  
yzx •  
1
2
3
4
5
6
7
1
2
3
4
5
6
7
MENU  
DVDMENU  
ENTER  
SET UP  
EXIT  
8
9
8
9
FAV  
LANGUAGE  
CLOCK SET  
ANT1 / 2  
ENGL I SH  
0 0 : 0 0  
ANT1  
10  
11  
12  
13  
14  
15  
16  
17  
18  
10  
11  
12  
13  
14  
15  
16  
17  
18  
TV  
TV / CABLE  
CH PROGRAM  
ADD / ERASE  
CABLE  
CBL/SAT CH  
VCR  
VOL  
ADD  
DVD  
QU I C K CONNECT GU I DE  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
3. Press x or • to enter the Quick Connection Guide mode.  
Advance the setup according to the guide displayed on the screen.  
You can set up the following items.  
Note:  
To stop the Quick Connect Guide, press EXIT  
or turnoff the TV.  
On-screen display language selection  
▼
Yes  
No  
Cable box selection (Yes/No)  
▼
▼
Cable box connection  
Cable or Antenna connection  
▼
▼
Cable box output channel selection  
(ch3/ch4)  
TV (antenna)/Cable source selection  
▼
▼
Select channels using Cable box  
(Confirmation only)  
Automatic channel programming  
Clock setting  
▼
Picture mode selection  
▼
Push  
“End”  
“Please push TOUCHFOCUS”  
▼
▼
Automatic convergence adjustment  
Basic setup has been completed  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Changing channels  
To change to a specific channel (programmed or unprogrammed):  
Press the Channel Number buttons (0–9 and 100).  
For channels 100 and higher, press the 100 button, and then the  
next two numbers. For example, to select channel 125, press 100,  
2, 5.  
POWER  
RECALL  
INFO  
TV/VIDEO  
1
4
2
5
8
3
6
Channel  
Number  
To change to the next programmed channel:  
9
CHRTN  
7
Press Channel y or z on the TV or remote control.  
+10  
100  
0
ENT  
Changing channels using SpeedSurf  
FAV  
PIC SIZE  
FAVORITE  
To use SpeedSurf to change to a specific programmed channel:  
MENU  
DVDMENU  
1. Press and hold Channel y or z for about one second. The TV  
will enter the SpeedSurf mode.  
ENTER  
EXIT  
FAV  
TV  
Channel yz  
CBL/SAT CH  
VCR  
VOL  
DVD  
Upper channels  
↑
16  
13  
11  
7
TBS  
ESPN  
FOX  
CBS  
CNN  
Current channel (highlighted)  
4
↓
Lower channels  
Channel label (if set)  
2. Repeatedly press or hold Channel y or z while the SpeedSurf  
mode is on-screen to scroll the channel list. Release the button to  
display the highlighted channel.  
Adjusting the color convergence  
This projection TV uses three separate TV tubes: red, green, and blue.  
The red, green, and blue images are projected onto the screen where  
they converge to form a full-color picture. You can see a clear picture  
only when the three images converge correctly. Convergence may drift  
over time or if you move the TV. If you can see clear images on your  
TV screen, skip this procedure.  
It is recommended that the adjustment is made only after the TV has  
been on for at least 30 minutes.  
Automatically adjusting the color convergence using  
TouchFocus™  
Press TOUCHFOCUS on the TV once. The TV will enter auto-  
convergence mode, and adjust convergence automatically.  
TV front panel  
Touch Focus  
MENU  
VOLUME  
CHANNEL  
EXIT TV/VIDEO  
TOUCH FOCUS F I N I SHED  
TOUCH FOCUS  
TouchFocus™  
When the adjustment is complete, the normal picture appears.  
If the error message “Touch Focus Error” appears, retry the  
TouchFocus adjustment.  
(continued on next page)  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Manually adjusting the color convergence  
1. Press MENU, and then press x or • until the PICTURE menu  
POWER  
RECALL  
INFO  
TV/VIDEO  
appears.  
2. Press y or z to highlight CONVERGENCE (below left).  
1
4
2
5
8
3
6
3. Press x or • to display the Center Convergence menu (below  
right).  
Number  
9
CHRTN  
7
32  
18 19 20 21 22 23 24 25 26 27 28 29 30 31  
1
2
3
4
5
6
7
8
9
10 11 12 131714 15 16  
+10  
100  
0
ENT  
FAV  
PIC  
P I CTURE ANTENNA  
SPORTS  
SI  
ZE  
FAVORITE  
MODE  
FLESH TONE  
CableClear DNR  
COLOR  
ON  
OFF  
MENU  
yzx •  
MENU  
DVDMENU  
RED  
BLUE  
: TO ADJUST  
ENTER : TO SELECT COLOR  
TEMPERATURE  
DISPLAY FORMAT  
CONVERGENCE  
COOL  
1080 i  
EX  
I
T
: TO SELECT POS I T I ON  
SAVE NEW PREFERENCE  
ENTER  
EXIT  
EXIT  
FAV  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32  
TV  
CBL/SAT CH  
VCR  
VOL  
If you see separate red, blue, or green crossed lines (or red or blue  
shadows next to white lines), you need to adjust the convergence.  
ENTER  
DVD  
4. Press ENTER to highlight RED or BLUE, depending on which  
color needs adjusting. If both red and blue need adjusting, you  
will need to perform steps 4 and 5 twice.  
5. Press y (up), z (down), x (left), or • (right) on the remote  
control to converge the red or blue line into the green line, which  
will turn completely white when correctly adjusted. When color  
convergence is correctly adjusted, you will see two single crossed  
white lines.  
6. Press EXIT to display the Circumference Convergence menu.  
7. Press the corresponding Number button (1–4 and 6–9) to select  
the area you want to adjust.  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
1
2
3
4
5
6
7
1
2
3
4
5
6
7
1
4
2
3
6
9
8
9
8
9
10  
11  
12  
13  
14  
15  
16  
17  
18  
10  
11  
12  
13  
14  
15  
16  
17  
18  
PUSH 1 – 9  
7
8
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
8. Press ENTER to highlight RED or BLUE, depending on which  
color needs adjusting. If both red and blue need adjusting, you  
will need to perform steps 8 and 9 twice for the selected area.  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
1
2
3
4
5
6
7
1
2
3
4
5
6
7
8
9
8
9
10  
11  
12  
13  
14  
15  
16  
17  
18  
10  
11  
12  
13  
14  
15  
16  
17  
18  
BLUE  
RED  
: TO ADJUST  
ENTER : TO SELECT COLOR  
EX I T : TO SELECT POS I T I ON  
1
32 33 34 35  
9. Press yzx • to converge the red or blue line into the green line,  
which will turn completely white when correctly adjusted. Repeat  
steps 8 and 9 until you see two single crossed white lines.  
10. Press EXIT once to select another area to adjust, and then repeat  
steps 7–9.  
11. Press EXIT twice to close the Convergence menu.  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the TV’s features  
Adjusting the channel settings  
Switching between two channels using Channel Return  
The Channel Return feature allows you to switch between two  
channels without entering an actual channel number each time.  
POWER  
RECALL  
INFO  
TV/VIDEO  
TV/VIDEO  
1
4
2
5
8
3
6
1. Select the first channel (or video mode) you want to view.  
2. Select a second channel using the Channel Number buttons  
(0–9, 100).  
Channel  
Number  
9
CHRTN  
7
+10  
3. Press CH RTN. The previous channel will display.  
100  
0
ENT  
CH RTN  
Each time you press CH RTN, the TV will switch back and forth  
between the last two channels that were selected.  
FAV  
PIC  
SI  
ZE  
ORITE  
FAV  
MENU  
DVDMENU  
Switching between two channels using SurfLock™  
The SurfLock™ feature temporarily “memorizes” one channel in the  
CH RTN button, so you can return to that channel quickly from any  
other channel by pressing CH RTN.  
ENTER  
EXIT  
FAV  
TV  
CBL/SAT CH  
VCR  
VOL  
DVD  
To memorize a channel in the CH RTN button:  
1. Select the channel you want to  
program into the CH RTN  
button.  
2. Press and hold CH RTN for about  
CHANNEL MEMOR I ZED  
ANT  
1
2 seconds until the message  
“Channel Memorized” appears  
(flashing) on the screen. The  
CABLE  
6
33 34 35  
channel has been programmed into the CH RTN button.  
3. Continue to change channels until your desired channel is  
selected.  
POWER  
RECALL  
TV/VIDEO  
INFO  
4. Press CH RTN. The memorized channel will be selected.  
1
4
7
2
3
6
The TV will return to the memorized channel one time only. Once  
you press CH RTN and then change channels again, the CH RTN  
button memory will be cleared and the button will function as  
Channel Return, by switching back and forth between the last two  
channels that were selected.  
5
8
9
CHRTN  
+10  
100  
0
ENT  
FAV  
PIC  
SI  
ORITE  
ZE  
FAV  
Programming your favorite channels  
MENU  
yzx •  
MENU  
DVDMENU  
You can preset up to 7 of your favorite channels each for FAVORITE  
CH1 and FAVORITE CH2 modes using the Favorite Channel  
Programming feature. Because this feature scans through only your  
favorite channels, it allows you to skip other channels you do not  
normally watch.  
ENTER  
EXIT  
FAV  
TV  
CBL/SAT CH  
VCR  
VOL  
DVD  
To program your favorite channels:  
1. Press MENU, and then press x or • until the CUSTOM menu  
appears.  
2. Press y or z to highlight FAVORITE CH1 or FAVORITE CH2.  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
1
2
3
4
5
6
7
1
2
3
4
5
6
7
1
2
3
4
5
6
7
1
2
3
4
5
6
7
CUSTOM  
CUSTOM  
8
9
8
9
8
9
8
9
T I MER  
ON  
T I MER  
ON  
00h00m  
0h00m  
OFF  
00h00m  
0h00m  
OFF  
10  
11  
12  
13  
14  
15  
16  
17  
18  
10 10  
11 11  
12 12  
13 13  
14 14  
15 15  
16 16  
17 17  
18 18  
10  
11  
12  
13  
14  
15  
16  
17  
18  
SLEEP  
CC  
FAVOR I TE  
SLEEP  
CC  
FAVOR I TE  
CH1  
CH1  
FAVOR I TE CH2  
FAVOR I TE CH2  
CH LABEL I NG  
V I  
LABEL  
CH LABEL I NG  
V I  
LABEL  
DEO  
BACKGROUND  
DEO  
BACKGROUND  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
(continued on next page)  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Notes:  
3. Press x or • to display the FAVORITE CH1 menu, for example.  
• The FAV zy buttons operate as  
MENU x • buttons when a menu is on-  
screen.  
CH INPUT will be highlighted.  
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
1
2
3
4
5
6
7
• The favorite channel feature is not available  
in ANT2 mode.  
CUSTOM  
8
9
8
9
T I MER  
ON  
10  
11  
12  
13  
14  
15  
16  
17  
18  
10  
11  
12  
13  
14  
15  
16  
17  
18  
00h00m  
0h00m  
OFF  
SLEEP  
CC  
FAVOR I TE  
CH1  
CH I NPUT  
FAVOR I TE CH2  
0
0
0
0
0
0
0
CH LABEL I NG  
V I  
LABEL  
DEO  
BACKGROUND  
TV CABLE  
CLEAR ALL  
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
1
2
3
4
5
6
7
8
9
4. Press the Channel Number buttons to enter one of your favorite  
channels.  
5. Press ENTER.  
6. Repeat steps 4 and 5 for other channels.  
To select your favorite channels:  
Press FAV z or y.  
POWER  
RECALL  
INFO  
TV/VIDEO  
To quickly scan through your favorite channels in a seven-picture  
multi-window:  
1
4
2
5
8
3
6
Press FAVORITE (see page 37).  
Channel  
Number  
9
CHRTN  
7
+10  
To clear a favorite channel:  
100  
0
ENT  
FAVORITE  
1. Press MENU, and then press x or • until the CUSTOM menu  
FAV  
PIC  
SI  
ZE  
appears.  
FAVORITE  
2. Press y or z to highlight FAVORITE CH2, for example.  
MENU  
MENU  
DVDMENU  
yzx •  
3. Press x or • to display the FAVORITE CH2 menu.  
ENTER  
FAV yz  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
EXIT  
1
2
3
4
5
6
7
1
2
3
4
5
6
7
FAV  
ENTER  
TV  
CBL/SAT CH  
VCR  
VOL  
CUSTOM  
DVD  
8
9
8
9
T I MER  
ON  
10  
11  
12  
13  
14  
15  
16  
17  
18  
10  
11  
12  
13  
14  
15  
16  
17  
18  
00h00m  
0h00m  
OFF  
SLEEP  
CC  
FAVOR I TE  
CH1  
FAVOR I TE CH2  
CH I NPUT  
CH LABEL I NG  
V I  
LABEL  
2
6
8
20  
DEO  
15  
0
18  
TV CABLE  
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
BACKGROUND  
1
2
3
4
5
6
7
8
9
CLEAR ALL  
4. Press yzx • to highlight the channel you want to clear, then  
press ENTER.  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
1
2
3
4
5
6
7
1
2
3
4
5
6
7
CUSTOM  
8
9
8
9
T I MER  
ON  
10  
11  
12  
13  
14  
15  
16  
17  
18  
10  
11  
12  
13  
14  
15  
16  
17  
18  
00h00m  
0h00m  
OFF  
SLEEP  
CC  
FAVOR I TE  
CH1  
FAVOR I TE CH2  
CH I NPUT  
CH LABEL I NG  
V I  
LABEL  
2
6
8
20  
DEO  
15  
0
18  
TV CABLE  
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
BACKGROUND  
1
2
3
4
5
6
7
8
9
CLEAR ALL  
5. Repeat step 4 for other channels.  
To clear all favorite channels at once:  
Press y or z to highlight CLEAR ALL in step 4 above, and then  
press x or • to clear all favorite channels at once.  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
1
2
3
4
5
6
7
1
2
3
4
5
6
7
CUSTOM  
8
9
8
9
T I MER  
ON  
10  
11  
12  
13  
14  
15  
16  
17  
18  
10  
11  
12  
13  
14  
00h00m  
0h00m  
OFF  
SLEEP  
CC  
FAVOR I TE  
CH1  
FAVOR I TE CH2  
CH I NPUT  
15  
16  
CH LABEL I NG  
V I  
LABEL  
0
0
0
0
0
0
0
DEO  
BACKGROUND  
17  
18  
TV CABLE  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21
CLEAR ALL  
28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Labeling channels  
Channel labels appear above the on-screen channel number display  
each time you turn on the TV, change a channel, or press RECALL.  
You can choose any four characters to identify a channel.  
POWER  
RECALL  
INFO  
TV/VIDEO  
To create channel labels:  
1
4
2
5
8
3
6
1. Press MENU, and then press x or • until the CUSTOM menu  
appears.  
Channel  
Number  
9
CHRTN  
7
2. Press y or z to highlight CH LABELING.  
3. Press x or • to display the CH LABELING menu.  
CH INPUT will be highlighted.  
+10  
100  
0
ENT  
FAV  
PIC  
SI  
ZE  
FAVORITE  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
MENU  
1
2
3
4
5
6
7
1
2
3
4
5
6
7
MENU  
DVDMENU  
yzx •  
ENTER  
CUSTOM  
EXIT  
8
9
8
9
FAV  
T I MER  
ON  
10  
11  
12  
13  
14  
15  
16  
17  
18  
10  
11  
12  
13  
14  
15  
16  
17  
18  
00h00m  
0h00m  
OFF  
ENTER  
SLEEP  
CC  
FAVOR I TE  
TV  
CBL/SAT CH  
VCR  
VOL  
CH1  
FAVOR I TE CH2  
DVD  
CH LABEL I NG  
V I  
LABEL  
CH I NPUT  
LABEL  
CLEAR  
– – – –  
DEO  
BACKGROUND  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20  
4. Press the Channel Number buttons to select a channel you want  
to label.  
5. Press z to highlight LABEL.  
6. Press x or • repeatedly to select a character for the first space,  
and then press ENTER.  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
1
2
3
4
5
6
7
1
2
3
4
5
6
7
1
2
3
4
5
6
7
1
2
3
4
5
6
7
CUSTOM  
CUSTOM  
8
9
8
9
8
9
8
9
T I MER  
ON  
T I MER  
ON  
10  
10  
11  
00h00m  
0h00m  
OFF  
10  
11  
12  
13  
14  
15  
16  
17  
18  
10  
00h00m  
0h00m  
OFF  
11  
11  
12  
SLEEP  
CC  
FAVOR I TE  
SLEEP  
CC  
FAVOR I TE  
12  
12  
13  
13  
14  
13  
14  
15  
16  
17  
18  
CH1  
CH1  
FAVOR I TE CH2  
14  
FAVOR I TE CH2  
15  
15  
16  
CH LABEL I NG  
V I  
LABEL  
CH I NPUT  
LABEL  
CLEAR  
6
A– – –  
CH LABEL I NG  
V I  
LABEL  
CH I NPUT  
LABEL  
CLEAR  
6
– – – –  
DEO  
BACKGROUND  
16  
DEO  
BACKGROUND  
17  
17  
18  
18  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20  
7. Repeat step 6 to enter the rest of the characters.  
If you would like a blank space in the label name, you must  
choose an empty space from the list of characters. Otherwise, a  
dash “–” will appear in that space.  
8. Repeat steps 4–7 for other channels. You can assign labels to a  
maximum of 32 channels.  
To erase channel labels:  
1. Press MENU, and then press x or • until the CUSTOM menu  
appears.  
2. Press y or z to highlight CH LABELING.  
3. Press x or • to display the CH LABELING menu.  
4. Press z to highlight CH INPUT, then select the channel you  
want to clear with the Channel Number buttons.  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
5. Press z to highlight  
CLEAR.  
6. Press x or • to erase the  
CUSTOM  
T I MER  
ON  
channel label.  
00h00m  
0h00m  
OFF  
SLEEP  
CC  
12  
CH1  
FAVOR I TE  
7. Repeat steps 4–6 to erase  
other channel labels.  
FAVOR I TE CH2  
CH LABEL I NG  
V I  
CH I NPUT  
LABEL  
CLEAR  
6
ABCD  
LABEL  
DEO  
BACKGROUND  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Viewing the wide-screen picture formats  
(480i and 480p signals only)  
POWER  
RECALL  
INFO  
TV/VIDEO  
You can view 480i and 480p format programs in a variety of picture  
sizes—Natural, Theater Wide 1, Theater Wide 2, Theater Wide 3,  
and Full.  
1
4
2
5
8
3
6
Number  
9
CHRTN  
7
The way the image displays in any of the picture sizes will vary  
depending on the format of the program you are viewing. Select the  
picture size that displays the current program the way that looks best  
to you. See “Notice of possible adverse effects on TV picture tube,”  
below right.  
+10  
100  
0
ENT  
FAV  
P
IC  
SIZE  
PIC SIZE  
FAVORITE  
MENU  
DVDMENU  
yzx •  
ENTER  
Selecting the picture size  
EXIT  
FAV  
1. Press PIC SIZE on the remote control.  
TV  
CBL/SAT CH  
VCR  
VOL  
2. Press the corresponding number button (0–4) to select the  
desired picture size, as described below and on the next page.  
DVD  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
P I CTURE S I ZE  
0 : NATURAL  
Note:  
1 :  
THEATER W I DE  
1
2
3
2 :  
THEATER W I DE  
3 : THEATER W I DE  
4 :  
FULL  
• The PICTURE SIZE feature is not available  
for some program formats (such as 1080i  
or 720p). Such formats will display in  
Natural picture size.  
0 – 4 : TO SELECT  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
• You also can change the picture size by  
selecting PICTURE SIZE in the THEATER  
menu.  
Natural picture size  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
• The image is displayed close to its originally formatted proportion.  
Some program formats will display with side bars and/or bars at the  
top and bottom (see examples below).  
THEATER  
WOW  
ON  
ON  
OFF  
SRS 3D  
FOCUS  
T r u B a s s  
P I CTURE S I ZE  
AUTO ASPECT  
P I CTURE SCROLL  
C I NEMA MODE  
OFF  
V I DEO  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
NOTICE OF POSSIBLE ADVERSE  
EFFECTS ON TV PICTURE TUBE  
Avoid displaying stationary images on  
your TV screen for extended periods of  
time. Fixed (non-moving) images (such  
as still PIP/POP windows or black/gray  
bars in wide-screen picture or PIP/POP  
formats) can become permanently  
engrained in the picture tube. This type  
of damage is NOT COVERED BY  
YOUR WARRANTY because it is the  
result of misuse. See item 33 on page 4.  
Natural picture size examples: The way the image displays will vary  
depending on the format of the program you are currently watching.  
See “Notice of possible adverse effects on TV picture tube” at right.  
(Continued)  
30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Theater Wide 1 picture size  
Note:  
• The picture is non-uniformly  
enlarged—the center of the  
picture remains close to its  
original proportion, but the left  
and right edges are stretched  
wider to fill the screen.  
• To adjust the picture size, press PIC SIZE  
on the remote control or select PICTURE  
SIZE in the THEATER menu.  
• The PICTURE SIZE feature is not available  
for some program formats (such as 1080i  
or 720p). Such formats will display in  
Natural picture size (see page 30).  
• A small part of the picture at  
the top and bottom is hidden;  
however, this mode cannot be  
scrolled.  
Theater Wide 1 picture size example  
• If you select Theater Wide 2 or 3, the top  
and bottom edges of the picture may be  
hidden. To see the hidden edges, either  
scroll the picture (see page 32) or try  
viewing the program in Full picture size.  
Theater Wide 2 picture size  
• The entire picture is uniformly  
enlarged—it is stretched the  
same amount both wider and  
taller (retains its original  
proportion).  
• Part of the picture at the top  
and bottom is hidden. To view  
the hidden areas, see “Scrolling  
the Theater Wide picture” on  
page 32.  
NOTICE OF POSSIBLE ADVERSE  
EFFECTS ON TV PICTURE TUBE  
Avoid displaying stationary images on  
your TV screen for extended periods of  
time. Fixed (non-moving) images (such  
as still PIP/POP windows or black/gray  
bars in wide-screen picture or PIP/POP  
formats) can become permanently  
Theater Wide 2 picture size example  
engrained in the picture tube. This type  
of damage is NOT COVERED BY  
YOUR WARRANTY because it is the  
result of misuse. See item 33 on page 4.  
Theater Wide 3 picture size  
• The picture is non-uniformly  
enlarged—it is stretched wider  
to fill the width of the screen,  
but only slightly stretched taller.  
• A small part of the picture at the  
top and bottom is hidden. To  
view the hidden areas (such as  
subtitles or captions), see  
“Scrolling the Theater Wide  
picture” on page 32.  
Theater Wide 3 picture size example  
Using the special functions to change the  
size of the displayed image (for example,  
changing the width/height ratio) for the  
purpose of public display or commercial  
gain may infringe on copyright laws.  
Full picture size  
• The picture is non-uniformly  
enlarged—it is stretched wider  
to fill the width of the screen,  
but not stretched taller.  
• None of the picture is hidden.  
Full picture size example  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Scrolling the Theater Wide picture  
(Theater Wide 2 and 3 only)  
1. Press PIC SIZE to select either Theater Wide 2 or Theater  
Wide 3 mode.  
POWER  
RECALL  
INFO  
TV/VIDEO  
2. Press MENU, and then press x or • until the THEATER menu  
1
4
2
5
8
3
6
appears.  
3. Press y or z to highlight PICTURE SCROLL.  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
9
CHRTN  
7
1
2
3
4
5
6
7
1
2
3
4
5
6
7
+10  
100  
0
ENT  
FAV  
P
IC  
THEATER  
SIZE  
8
9
8
9
PIC SIZE  
WOW  
FAVORITE  
10  
11  
12  
13  
14  
15  
16  
17  
18  
SRS 3D  
FOCUS  
T r u B a s s  
P I CTURE S I ZE  
AUTO ASPECT  
P I CTURE SCROLL  
C I NEMA MODE  
ON  
ON  
10  
11  
12  
13  
14  
15  
16  
17  
18  
OFF  
MENU  
MENU  
DVDMENU  
OFF  
yzx •  
V I DEO  
ENTER  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
EXIT  
FAV  
TV  
CBL/SAT CH  
VCR  
VOL  
4. Press x or • to display the scroll adjustment mode.  
DVD  
Note:  
SCROLL ADJUSTMENT  
0
You can scroll the picture in Theater Wide 2  
:
TO ADJUST  
and Theater Wide 3 modes only. The scroll  
amounts are as follows:  
• 480i signal source:  
Theater Wide 1: Not adjustable  
Theater Wide 2: +20 to –10  
Theater Wide 3: +20 to –10  
5. Press y or z to adjust the vertical position of the picture.  
• Normal (center) position  
• 480p signal source:  
Theater Wide 1: Not adjustable  
Theater Wide 2: +20 to –10  
Theater Wide 3: +20 to –10  
SCROLL ADJUSTMENT  
0
• 720p signal source: Not adjustable  
• 1080i signal source: Not adjustable  
:
TO ADJUST  
NOTICE OF POSSIBLE ADVERSE  
EFFECTS ON TV PICTURE TUBE  
• To raise the picture, press y .  
Avoid displaying stationary images on  
your TV screen for extended periods of  
time. Fixed (non-moving) images (such  
as still PIP/POP windows or black/gray  
bars in wide-screen picture or PIP/POP  
formats) can become permanently  
SCROLL ADJUSTMENT  
+20  
:
TO ADJUST  
engrained in the picture tube. This type  
of damage is NOT COVERED BY  
YOUR WARRANTY because it is the  
result of misuse. See item 33 on page 4.  
• To lower the picture, press z.  
SCROLL ADJUSTMENT  
–10  
:
TO ADJUST  
32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the AUTO ASPECT feature (480i signals only)  
When the AUTO ASPECT feature is set to ON and the TV receives a Note:  
480i signal, the picture size is automatically selected (as described in  
the following table).  
The AUTO ASPECT feature is not available  
when viewing antenna (cable) or DVI input  
sources.  
Automatic aspect size  
Aspect ratio of signal source  
(automatically selected  
when AUTO ASPECT is ON)  
POWER  
RECALL  
INFO  
TV/VIDEO  
4:3  
16:9  
Theater Wide 2  
Full  
1
4
2
5
8
3
6
Not defined (no ID-1 data)  
User-selected picture size (pgs. 30–31)  
9
CHRTN  
7
+10  
If the signal does not include aspect information, the picture size you  
selected on pages 30–31 is displayed.  
100  
0
ENT  
FAV  
P
IC  
SIZE  
FAVORITE  
To turn on the AUTO ASPECT feature:  
MENU  
yzx •  
MENU  
DVDMENU  
1. Press MENU, and then press x or • until the THEATER menu  
appears.  
ENTER  
EXIT  
2. Press y or z to highlight AUTO ASPECT, and then press x or  
FAV  
• to select ON.  
TV  
CBL/SAT CH  
VCR  
VOL  
DVD  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
1
2
3
4
5
6
7
1
2
3
4
5
6
7
THEATER  
8
9
8
9
WOW  
10  
11  
12  
13  
14  
15  
16  
17  
18  
SRS 3D  
FOCUS  
T r u B a s s  
P I CTURE S I ZE  
AUTO ASPECT  
P I CTURE SCROLL  
C I NEMA MODE  
ON  
ON  
10  
11  
12  
13  
14  
15  
16  
17  
18  
NOTICE OF POSSIBLE ADVERSE  
OFF  
ON  
EFFECTS ON TV PICTURE TUBE  
V I DEO  
Avoid displaying stationary images on  
your TV screen for extended periods of  
time. Fixed (non-moving) images (such  
as still PIP/POP windows or black/gray  
bars in wide-screen picture or PIP/POP  
formats) can become permanently  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
engrained in the picture tube. This type  
of damage is NOT COVERED BY  
YOUR WARRANTY because it is the  
result of misuse. See item 33 on page 4.  
33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Note:  
Using the POP double-window feature  
• You cannot access POP features when  
viewing DVI input.  
The POP (picture-out-picture) feature splits the screen into a double  
window that allows you to watch two programs at the same time. The  
POP program can come from a TV broadcast or an external source,  
such as a VCR.  
• You cannot display an ANT-2 signal source  
in the POP window.  
• You can choose to output the sound of  
either the main or POP program from the  
AUDIO OUT jacks (see “Selecting the  
Audio OUT sound” on page 55). The TV’s  
speakers always output the sound of the  
To display a TV broadcast in the POP window:  
1. Press SPLIT to display the POP window.  
main picture.  
Main window  
POP window  
1
4
2
5
8
3
6
POP  
12  
Channel  
Number  
9
CHRTN  
7
+10  
100  
0
ENT  
2. Select channels of the POP window in the following two ways:  
E
FAV  
M
PI  
E
C
S
• To change to a specific channels, press POP DIRECT CH.  
While “POP” is on the screen, press the Channel Number  
buttons (0-9 and 100).  
IZE  
VORITE  
FA  
MENU  
DVDMENU  
• To change the next programmed channels, press POP CH  
zy.  
ENTER  
EXIT  
N
EXIT  
C
FAV  
If the V-CHIP feature is active and you try to watch a TV  
program that exceeds your set rating limits, the program will be  
blocked (see “Using the V-CHIP menu” on page 39).  
TV  
CBL/SAT CH  
VCR  
VOL  
DVD  
POP DIRECT CH  
SPLIT  
POP DIRECT CH MUTE  
SLEEP  
TV/VCR PAUSE  
STOP  
PLAY  
SPLIT  
FREEZE SOURCE  
REW  
FF  
SKIP/SEARCH  
SOURCE  
CH SCAN  
REC  
SWAP  
POP CH  
LIGHT  
POP CH zy  
POP  
24  
BLOCKED  
To display a picture from an external source in the POP window:  
1. Connect the external source equipment (see “Connecting your  
TV” on page 8).  
2. Select the TV program you want to watch in the main window.  
3. Press SPLIT to display the POP window.  
4. Repeatedly press SOURCE to select the input source for the POP  
window (VIDEO 1, VIDEO 2, VIDEO 3, ColorStream HD1,  
or ColorStream HD2 only; you cannot select DVI in POP  
mode). The current source will display in purple.  
NOTICE OF POSSIBLE ADVERSE  
EFFECTS ON TV PICTURE TUBE  
Avoid displaying stationary images on  
your TV screen for extended periods of  
time. Fixed (non-moving) images (such  
as still PIP/POP windows or black/gray  
bars in wide-screen picture or PIP/POP  
formats) can become permanently  
engrained in the picture tube. This type  
of damage is NOT COVERED BY  
YOUR WARRANTY because it is the  
result of misuse. See item 33 on page 4.  
5. You can play a tape as the POP picture, or select a channel for the  
POP window using the VCR’s channel keys.  
POP SOURCE SELECT I ON  
0 : TV  
1 : V IDEO  
2 : V IDEO  
3 : V IDEO  
1
2
3
4 : Color Stream HD1  
5 : Color Stream HD2  
0 - 5 : TO SELECT  
While the above menu is on the screen, you can select the desired  
signal input source by pressing the corresponding number button  
(0-5).  
To close the POP window:  
Press SPLIT again or EXIT.  
34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Switching the main and POP pictures  
Press SWAP while you are using the POP feature to switch the main  
and POP pictures.  
FAV  
MENU  
DVDMENU  
x •  
Freezing the POP picture  
EXIT  
FAV  
1. Press FREEZE while the POP is not on the screen.  
The POP window will appear with a still picture.  
TV  
CBL/SAT CH  
VCR  
VOL  
DVD  
2. Press FREEZE again to renew the still picture.  
POP DIRECT CH MUTE  
SLEEP  
FREEZE  
SWAP  
TV/VCR PAUSE  
STOP  
PLAY  
SPLIT  
FREEZE SOURCE  
REW  
FF  
SKIP/SEARCH  
CH SCAN  
REC  
SWAP  
POP CH  
LIGHT  
To erase the still POP window:  
Press EXIT.  
Still picture  
Adjusting the size of the double-window  
When the input signals of the main and POP pictures are 480i, you  
can adjust the size of each window. Repeatedly press x or • to change  
the size (in 9 steps).  
Note:  
Only 480i signals can be adjusted in the POP  
double window. If a signal format other than  
480i is received and you press x or •, the  
message “Not available” will appear  
on-screen.  
NOTICE OF POSSIBLE ADVERSE  
EFFECTS ON TV PICTURE TUBE  
Avoid displaying stationary images on  
your TV screen for extended periods of  
time. Fixed (non-moving) images (such  
as still PIP/POP windows or black/gray  
bars in wide-screen picture or PIP/POP  
formats) can become permanently  
engrained in the picture tube. This type  
of damage is NOT COVERED BY  
YOUR WARRANTY because it is the  
result of misuse. See item 33 on page 4.  
35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
POP double-window aspect ratio  
The POP double-window feature displays each picture according to  
its input signal aspect ratio, as illustrated below.  
Note:  
• The AUTO ASPECT feature (page 33) does  
not operate in POP double-window mode.  
• Aspect ratio is the ratio of width to height of  
the picture.  
480i  
480i  
480p-720p  
480i  
POP  
13  
FAV  
PI  
C
S
IZE  
FAVORITE  
MENU  
DVDMENU  
yzx •  
ENTER  
EXIT  
FAV  
ENTER  
TV  
CBL/SAT CH  
VCR  
VOL  
480i  
480p-720p  
480p-720p  
480p-720p  
DVD  
POP DIRECT CH MUTE  
SLEEP  
TV/VCR PAUSE  
STOP  
PLAY  
SPLIT  
FREEZE SOURCE  
CH SCAN  
REW  
FF  
SKIP/SEARCH  
CH SCAN  
REC  
SWAP  
POP CH  
LIGHT  
Using the programmed channel search function  
You can use the programmed channel search function to quickly scan  
the channels you programmed into the TV’s memory (page 23).  
1. Press CH SCAN.  
The TV automatically enters POP mode, and begins a seven-  
picture scan of your programmed channels.  
Note:  
3
4
5
6
7
During the programmed channel search, all  
main and POP windows display in 16:9 aspect  
ratio, regardless of the signal format.  
8
9
10  
CABLE  
10  
2. Press yzx • to select one of the seven pictures. The selected  
pictures becomes a moving picture. (The main picture is always  
moving.)  
NOTICE OF POSSIBLE ADVERSE  
EFFECTS ON TV PICTURE TUBE  
3. Press ENTER to display the channel you selected in step 2 as a  
normal picture.  
Avoid displaying stationary images on  
your TV screen for extended periods of  
time. Fixed (non-moving) images (such  
as still PIP/POP windows or black/gray  
bars in wide-screen picture or PIP/POP  
formats) can become permanently  
engrained in the picture tube. This type  
of damage is NOT COVERED BY  
YOUR WARRANTY because it is the  
result of misuse. See item 33 on page 4.  
Moving picture  
3
4
5
6
7
8
9
36  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the favorite channel search function  
You can use the favorite channel search function to quickly scan your  
favorite channels (see “Programming your favorite channels” on  
page 27).  
Note:  
The favorite channel search function does not  
operate in DVI mode.  
1. Press FAVORITE.  
The TV automatically enters POP mode, and begins a seven-  
picture scan of your favorite channels in the POP window.  
POWER  
RECALL  
INFO  
TV/VIDEO  
3
4
5
6
7
1
4
2
5
8
3
6
8
9
9
CHRTN  
7
+10  
6
CABLE  
6
100  
0
ENT  
FAVORITE  
FAV  
PIC  
SI  
ORITE  
FAV  
ZE  
2. Press yzx • to select one of the seven pictures (becomes a  
moving picture). The main picture is an always moving picture.  
MENU  
DVDMENU  
3. Press ENTER to display the channel you selected in step 2 as a  
normal picture.  
yzx •  
ENTER  
EXIT  
FAV  
Moving picture  
ENTER  
TV  
CBL/SAT CH  
VCR  
VOL  
DVD  
3
4
5
6
7
8
9
6
Every time you press FAVORITE, the POP window scans your  
favorite channels in the following order:  
NOTICE OF POSSIBLE ADVERSE  
EFFECTS ON TV PICTURE TUBE  
FAVORITE CH1 — FAVORITE CH2 — Off  
Avoid displaying stationary images on  
your TV screen for extended periods of  
time. Fixed (non-moving) images (such  
as still PIP/POP windows or black/gray  
bars in wide-screen picture or PIP/POP  
formats) can become permanently  
engrained in the picture tube. This type  
of damage is NOT COVERED BY  
YOUR WARRANTY because it is the  
result of misuse. See item 33 on page 4.  
About the auto favorite feature  
If your TV is in the program lock mode, after 4 seconds the TV starts  
the auto favorite channel search function. See page 41 for details.  
3
4
5
6
7
8
THIS PROGRAM HAS BEEN BLOCKED!  
TV–PG  
L
V
EXCEEDS SET L I M I TS  
PUSH MUTE TO ENTER PIN  
CABLE  
9
37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the LOCKS menu  
Note:  
The LOCKS menu includes the V-Chip, CH Lock, Video Lock, and  
New PIN Code functions. You can use these functions after entering  
the correct PIN code.  
The V-Chip function is available only for the  
U.S. V-Chip system. The Canadian V-Chip  
system is not supported.  
Entering the PIN code  
1. Press MENU, and then press x or • until the LOCKS menu  
appears.  
POWER  
RECALL  
INFO  
TV/VIDEO  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
1
2
3
4
5
6
7
1
2
3
4
5
6
7
RECALL  
Number  
1
4
2
5
8
3
6
LOCKS  
8
9
8
9
V–CH I P  
ENABLE BLOCK I NG OFF  
TV RAT I NG  
10  
11  
12  
13  
14  
15  
16  
17  
18  
10  
11  
12  
13  
14  
15  
16  
17  
18  
MPAA RAT I NG  
BLOCK I NG OPT I ON  
CH LOCK  
9
CHRTN  
7
+10  
V I DEO LOCK  
OFF  
OFF  
OFF  
GAME TIMER  
FRONT PANEL LOCK  
NEW P I N CODE  
100  
0
ENT  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
FAV  
PIC  
E
SI  
ZE  
FAVORITE  
2. Press y or z to display the PIN code entering mode.  
MENU  
MENU  
DVDMENU  
• Blocking Reset status:  
• Blocking Reset status (when the PIN  
yzx •  
Set your 4-digit code by pressing  
the Number buttons (0–9).  
code is already stored):  
ENTER  
N
EXIT  
C
Press the Number buttons (0–9) to  
enter the 4-digit PIN code used for  
blocking channels.  
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
FAV  
ENTER  
TV  
CBL/SAT CH  
VCR  
VOL  
DVD  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
1
2
3
4
5
6
7
1
2
3
4
5
6
7
1
2
3
4
5
6
7
LOCKS  
BLOCK I NG RESET  
LOCKS  
BLOCK I NG ACT I VE  
P I N CODE 1 23 4  
8
9
8
9
8
9
8
9
11 10  
P I N CODE  
10  
11  
12  
13  
14  
15  
16  
17  
18  
10  
11  
12  
13  
14  
15  
16  
17  
18  
10  
11  
12  
13  
14  
15  
16  
17  
18  
10  
11  
12  
13  
14  
15  
16  
17  
18  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
If the wrong PIN code is entered, the message “Incorrect”  
appears. Enter the code again, and then press ENTER.  
If you cannot remember your PIN code  
While the PIN code entering screen is displayed, press RECALL  
four times within five seconds. The PIN code will be released  
(Blocking Reset status restored).  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
1
2
3
4
5
6
7
1
2
3
4
5
6
7
LOCKS  
8
9
8
9
V–CH I P  
ENABLE BLOCK I NG ON/OFF  
TV RAT I NG  
10  
11  
12  
13  
14  
15  
16  
17  
18  
10  
11  
12  
13  
14  
15  
16  
17  
18  
MPAA RAT I NG  
BLOCK I NG OPT I ON  
CH LOCK  
V I DEO LOCK  
OFF  
OFF  
OFF  
GAME TIMER  
FRONT PANEL LOCK  
NEW P I N CODE  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
Continue to set each item following the steps on the next page.  
38  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the V-CHIP menu  
Note:  
Some TV programs and movies include signals that classify the  
content of the program (violence, sex, dialog, language). The V-CHIP  
conrol feature in this TV detects the signals and blocks the programs  
according to your selections. To use this feature, perform the  
following setup.  
The V-Chip function is available only for the  
U.S. V-Chip system. The Canadian V-Chip  
system is not supported.  
ENABLE BLOCKING  
1. From the LOCKS menu, select ENABLE BLOCKING.  
2. Press x or • to select ON or OFF.  
LOCKS menu  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
1
2
3
4
5
6
7
1
2
3
4
5
6
7
LOCKS  
ON : To enable your setting (Lock)  
8
9
8
9
V–CH I P  
ENABLE BLOCK I NG ON/OFF  
TV RAT I NG  
10  
11  
12  
13  
14  
15  
16  
17  
18  
10  
11  
12  
13  
14  
15  
16  
17  
18  
OFF: To release your setting (Unlock)  
Note: The CH LOCK function is not affected with this selection.  
MPAA RAT I NG  
BLOCK I NG OPT I ON  
CH LOCK  
OFF  
OFF  
OFF  
V I DEO LOCK  
GAME TIMER  
FRONT PANEL LOCK  
NEW P I N CODE  
TV RATING (Independent rating system for  
broadcasters)  
1. From the LOCKS menu, select TV RATING.  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
To select each item:  
Press z or y .  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
1
2
3
4
5
6
7
1
2
3
4
5
6
7
2. Press x or • to display  
the TV RATING menu.  
LOCKS  
3. Press z or y to select item.  
4. Press • to lock (display “X” )  
Press x to unlock (display “✓ ”)  
8
9
8
9
TV RAT I NG MA 14 PG  
DI ALOG  
LANGUAGE  
G
Y
POWER  
RECALL  
INFO  
TV/VIDEO  
10  
11  
12  
13  
14  
15  
16  
17  
18  
10  
11  
12  
13  
14  
15  
16  
17  
18  
SEX  
V I OLENCE  
NO DLSV  
YOUTH TV RAT I NG  
Y7FV Y7  
1
4
2
5
8
3
6
V–CH I P MENU  
5. Repeat steps 3 and 4 to set  
the next item.  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
9
CHRTN  
7
The TV age-based ratings and content themes you can be lock are  
listed in the table below.  
+10  
100  
0
ENT  
FAV  
PIC  
SI  
ZE  
Ratings  
MA  
Description and Content themes  
FAVORITE  
Mature Audience Only (This program is specifically  
designed to be viewed by adults and therefore may be  
unsuitable for children under 17.)  
MENU  
DVDMENU  
yzx •  
ENTER  
L) Crude or indecent language S) Explicit sexual activity  
V) Graphic violence  
EXIT  
FAV  
TV  
CBL/SAT CH  
VCR  
VOL  
14  
Parents Strongly Cautioned (This program contains some  
material that many parents would find unsuitable for  
children under 14 years of age.)  
D) Intensely suggestive dialog L) Strong, coarse language  
S) Intense sexual situations V) Intense violence  
DVD  
Press RECALL to display the rating of  
the TV program you are currently  
PG  
Parental Guidances Suggested (This program contains  
material that parents may find unsuitable for younger  
children.)  
watching.  
D) Some suggestive dialog L) Infrequent coarse  
language S) Some sexual situations V) Moderate  
violence  
STEREO  
SAP  
TV – PG  
L
V
PG  
L
V
G
General Audience (Most parents would find this program  
suitable for all ages.)  
ANT  
1
FULL  
CLOCK  
9
: 2 5  
CABLE  
6
33 34 35  
Y7,  
Directed to Older Children (This program is designed for  
Y7FV children age 7 and above. Note: Programs in which fantasy  
violence may be more intense or more combative than other  
programs in this category are designated Y7FV.)  
Y
All Children (This program is designed to be appropriate for  
all children.)  
39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MPAA RATING (Independent rating system for movies)  
1. From the LOCKS menu, select MPAA RATING.  
LOCKS menu  
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32  
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
2. Press x or • to display the MPAA RATING menu, then press z  
or y to highlight MPAA RATING.  
LOCKS  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
8
9
1
2
3
4
5
6
7
1
2
3
4
5
6
7
V–CH I P  
ENABLE BLOCK I NG ON  
TV RAT I NG  
10  
11  
12  
13  
14  
15  
16  
17  
18  
MPAA RAT I NG  
BLOCK I NG OPT I ON  
CH LOCK  
V I DEO LOCK  
OFF  
OFF  
OFF  
LOCKS  
8
9
8
9
GAME TIMER  
FRONT PANEL LOCK  
NEW P I N CODE  
MPAA RAT I NG  
X
10  
11  
12  
13  
14  
15  
16  
17  
18  
10  
11  
12  
13  
14  
15  
16  
17  
18  
NC17 R PG13 PG  
G
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32  
V–CH I P MENU  
To select each item:  
Press z or y .  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
3. Press • to lock (“X”) or press x to unlock (“✓”).  
The movie ratings you can lock are described as follows:  
X
: X-rated (For adults only)  
NC17: Not intended for anyone 17 and under  
R
: Restricted (Under 17 requires accompanying parent or adult  
guardian.)  
PG13 : Parents Strongly Cautioned (Some material may be  
inappropriate for children under 13)  
PG : Parental Guidance Suggested (Some material may not be  
suitable for children)  
G
: General Audience (Appropriate for all ages)  
POWER  
RECALL  
INFO  
TV/VIDEO  
BLOCKING OPTION  
1. From the LOCKS menu, select BLOCKING OPTION.  
1
4
2
5
8
3
6
2. Press x or • to display the BLOCKING OPTION menu,  
then press y or z to select item.  
9
CHRTN  
7
MPAA UNRATED:  
+10  
100  
0
ENT  
Press x or • to select ON (Lock) or OFF (Unlock) for unrated  
programs in the MPAA rating system.  
FAV  
PIC  
SI  
ZE  
FAVORITE  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31  
MENU  
DVDMENU  
1
2
3
4
5
6
7
1
2
3
4
5
6
7
yzx •  
ENTER  
LOCKS  
LOCKS  
EXIT  
8
9
8
9
FAV  
V–CH I P  
ENABLE BLOCK I NG ON  
TV RAT I NG  
BLOCK I NG OPT I ON  
MPAA UNRATED  
TV NONE RATING  
V–CH I P MENU  
10  
11  
12  
13  
14  
15  
16  
17  
18  
10  
11  
12  
13  
14  
15  
16  
17  
18  
ON/OFF  
OFF  
TV  
MPAA RAT I NG  
BLOCK I NG OPT I ON  
CH LOCK  
CBL/SAT CH  
VCR  
VOL  
DVD  
V I DEO LOCK  
OFF  
OFF  
OFF  
GAME TIMER  
FRONT PANEL LOCK  
NEW P I N CODE  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31  
TV NONE RATING  
Caution:  
Setting the TV None Rating to ON may block  
Press x or • to select ON (Lock) or OFF (Unlock) for programs  
rated NONE in the TV PARENTAL GUIDELINES.  
the broadcast of emergency information.The  
menu will display the note, “Enabling this  
option may block emergency messages” to  
warn you of this possibility.  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
1
2
3
4
5
6
7
1
2
3
4
5
6
7
LOCKS  
8
9
8
9
BLOCK I NG OPT I ON  
MPAA UNRATED  
TV NONE RATING  
V–CH I P MENU  
NOTE : ENABL I NG TH I S  
OPT I ON MAY BLOCK  
EMERGENCY MESSAGES  
10  
11  
12  
13  
14  
15  
16  
17  
18  
10  
11  
12  
13  
14  
15  
16  
17  
18  
ON  
ON  
/OFF  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
V-CHIP MENU:  
Press x or • to return to the LOCKS menu.  
40  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Unlocking programs temporarily  
1. If you try to watch a TV program that exceeds the rating limits  
you set, the TV enters program lock mode. After 4 seconds, the  
TV starts the auto favorite channel search function (see page 37).  
You can either unlock the program temporarily (see steps 2-4) or  
select a non-locked program to watch.  
After 4 seconds  
3
4
5
6
7
8
THIS PROGRAM HAS BEEN BLOCKED!  
TV–PG  
L
V
THIS PROGRAM HAS BEEN BLOCKED!  
TV–PG  
L
V
EXCEEDS SET L I M I TS  
EXCEEDS SET L I M I TS  
PUSH MUTE TO ENTER PIN  
PUSH MUTE TO ENTER PIN  
CABLE  
9
CABLE  
9
2. To temporarily unlock the program, press MUTE.  
3. Press the Number buttons (0-9) to enter your 4-digit PIN code.  
POWER  
RECALL  
INFO  
TV/VIDEO  
1
4
2
5
8
3
6
BLOCKI NG ACTI VE  
ENTER P I N CODE  
Channel  
Number  
TO TEMPORARI LY UN–BLOCK  
9
CHRTN  
7
––––  
+10  
100  
0
ENT  
0 –9 : TO SELECT ENTER: TO SET  
FAV  
PIC  
SI  
ZE  
FAVORITE  
4. Press ENTER.  
MENU  
DVDMENU  
If the correct code is entered, the program lock mode is released  
and the normal picture appears.  
yzx •  
ENTER  
EXIT  
FAV  
All locking is disabled until the TV is turned off, and will be  
enabled when the TV is turned on again.  
ENTER  
TV  
CBL/SAT CH  
VCR  
VOL  
DVD  
POP DIRECT CH MUTE  
SLEEP  
Locking channels  
With the CH LOCK feature, you can lock specific channels. The TV  
will not be able to tune locked channels with the Channel y z  
buttons or Channel Number buttons, unless you clear the setting.  
MUTE  
You can lock a maximum of nine channels.  
To lock channels:  
LOCKS menu  
1. From the LOCKS menu, select CH LOCK.  
LOCKS  
V–CH I P  
2. Press x or • to display the CH LOCK menu.  
ENABLE BLOCK I NG ON  
TV RAT I NG  
MPAA RAT I NG  
CH INPUT will be highlighted.  
BLOCK I NG OPT I ON  
CH LOCK  
V I DEO LOCK  
3. Press the Channel Number buttons to enter the channel you  
want to lock.  
OFF  
OFF  
OFF  
GAME TIMER  
FRONT PANEL LOCK  
NEW P I N CODE  
4. Press ENTER.  
To select each item:  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
1
2
3
4
5
6
7
1
2
3
4
5
6
7
1
2
3
4
5
6
7
Press z or y .  
3
4
5
6
7
LOCKS  
LOCKS  
8
9
8
9
8
9
8
9
V–CHIP  
ENABLEBLOCKING OFF  
TV RAT I NG  
V–CH I P  
0
1
1
1
1
1
1
0
1
2
3
4
5
6
7
8
10  
11  
12  
13  
14  
15  
16  
17  
ENABLEBLOCK ING OFF  
TV RATI NG  
MPAARATI NG  
MPAA RATI NG  
BLOCK ING OPTION  
3
4
5
6
7
8
BLOCK I NG OPTION  
CH LOCK  
VIDEO LOCK  
CH INPUT  
CH LOCK  
CH INPUT  
12  
0
12  
0
0
0
0
0
0
0
VIDEO LOCK  
0
0
0
0
0
0
GAME TIMER  
FRONT PANEL LOCK  
NEW P I N CODE  
0
GAME TIMER  
FRONT PANEL LOCK  
NEW P I N CODE  
1
0
0
1
1
TV CABLE  
TV CABLE  
CLEAR ALL  
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
18  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19  
C
20  
L
21  
2
E
2
23  
A
24R  
25 26  
A
27  
2
L
8
L
29 30 31 32 33 34 35  
1
2
3
4
5
6
7
8
9
5. Repeat steps 3 and 4 for other channels.  
41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
To unlock individual channels:  
1. From the LOCKS menu, select CH LOCK.  
2. Press x or • to display the CH LOCK menu.  
3. Press yzx • to highlight the channel you want to unlock, then  
press ENTER.  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
1
2
3
4
5
6
7
1
2
3
4
5
6
7
1
2
3
4
5
6
7
1
2
3
4
5
6
7
LOCKS  
LOCKS  
8
9
8
9
8
9
8
9
V–CHIP  
ENABLEBLOCK ING ON  
TV RATI NG  
V–CHIP  
ENABLEBLOCK ING ON  
TV RATI NG  
10  
11  
12  
13  
14  
15  
16  
17  
18  
10  
11  
12  
13  
14  
15  
16  
17  
18  
10  
11  
12  
13  
14  
15  
16  
17  
18  
1
1
1
1
1
1
1
1
1
MPAA RAT I NG  
MPAA RATI NG  
BLOCK ING OPT ION  
NG  
BLOCK I  
CH LOCK  
VIDEO LOCK  
OPT ION  
CH INPUT  
12 18 26  
33  
CH LOCK  
VIDEO LOCK  
CH INPUT  
12 18 33  
0
0
0
0
0
0
0
GAME TIMER  
GAME TIMER  
FRONT PANEL LOCK  
NEW P I N CODE  
0
0
0
TV CABLE  
0
FRONT PANEL LOCK  
NEW P I N CODE  
TV CABLE  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19  
C
20  
L
21  
2
E
2
23  
A
24R  
25 26  
A
27  
2
L
8
2
L
9
30 31 32 33 34 35  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19  
C
20  
L
21  
2
E
2
23  
A
24R  
25 26  
A
27  
2
L
8
L
29 30 31 32 33 34 35  
POWER  
RECALL  
INFO  
TV/VIDEO  
4. Repeat step 3 for other channels.  
To unlock all locked channels at once:  
Press y or z to highlight CLEAR ALL, and then press x or •.  
1
4
2
5
8
3
6
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
1
2
3
4
5
6
7
1
2
3
4
5
6
7
9
CHRTN  
7
+10  
100  
0
ENT  
LOCKS  
FAV  
PIC SIZE  
8
9
8
9
V–CHIP  
FAVORITE  
10  
11  
12  
13  
14  
15  
16  
17  
18  
10  
11  
12  
13  
14  
15  
16  
17  
18  
ENABLEBLOCK ING ON  
TV RATI NG  
MPAA RAT I NG  
MENU  
DVDMENU  
NG  
BLOCK I  
OPT ION  
CH LOCK  
VIDEO LOCK  
CH INPUT  
0
0
0
0
0
0
0
0
0
yzx •  
GAME TIMER  
FRONT PANEL LOCK  
NEW P I N CODE  
ENTER  
TV CABLE  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18
C
L
E
A
R  
A
L
L
EXIT  
FAV  
ENTER  
TV  
CBL/SAT CH  
VCR  
VOL  
Locking video inputs  
DVD  
With the VIDEO LOCK feature, you can lock out the input sources  
(Video 1, Video 2, Video 3, ColorStream HD1, ColorStream HD2,  
DVI/HDCP) and channels 3 and 4.  
You will not be able to select the input sources with the TV/VIDEO  
button or Channel buttons unless you clear the setting.  
To set up the video lock:  
1. From the LOCKS menu, select VIDEO LOCK.  
2. Press x or • to highlight the level of video locking you want  
(Video, Video+, or Off), as follows:  
VIDEO : Locks Video 1, Video 2, Video 3, ColorStream HD1,  
HD2, and DVI/HDCP.  
VIDEO+ : Locks Video 1, Video 2, Video 3, ColorStream,  
HD1/HD2, DVI/HDCP, and channels 3 and 4. This  
option should be used if you use the antenna terminal  
to play a video tape.  
Note: Make sure the POP is not on channel 3 or 4.  
OFF  
: Unlocks all video input sources.  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
1
2
3
4
5
6
7
1
2
3
4
5
6
7
LOCKS  
8
9
8
9
V–CH I P  
ENABLE BLOCK I NG ON  
TV RAT I NG  
10  
11  
12  
13  
14  
15  
16  
17  
18  
10  
11  
12  
13  
14  
15  
16  
17  
18  
MPAA RAT I NG  
BLOCK I NG OPT I ON  
CH LOCK  
+
V I DEO/ V I DEO / OFF  
V I DEO LOCK  
GAME TIMER  
FRONT PANEL LOCK  
NEW P I N CODE  
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
OFF  
1
2
3
4
5
6
7
8
9
42  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the game timer  
Note:  
You can use the GAME TIMER feature to automatically activate the  
VIDEO LOCK feature, to set a time limit for playing a video game (the  
VIDEO LOCK is set to VIDEO).  
To watch a VIDEO source after the game  
timer has activated the video lock, you will  
need to set the VIDEO LOCK feature to OFF  
(in the LOCKS menu).  
To set the game timer:  
1. From the LOCKS menu, select GAME TIMER.  
2. Press x or • to select the amount of time until the video lock is  
activated (30, 60, 90, or 120 minutes). When the number is  
highlighted, the timer will start countdown.  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
1
2
3
4
5
6
7
1
2
3
4
5
6
7
LOCKS  
8
9
8
9
V–CH I P  
ENABLE BLOCK I NG ON  
TV RAT I NG  
10  
11  
12  
13  
14  
15  
16  
17  
18  
10  
11  
12  
13  
14  
15  
16  
17  
18  
MPAA RAT I NG  
BLOCK I NG OPT I ON  
CH LOCK  
OFF  
V I DEO LOCK  
GAME TIMER  
OFF/ 30/ 60 / 90 / 120  
OFF  
FRONT PANEL LOCK  
NEW P I N CODE  
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
1
2
3
4
5
6
7
8
9
To cancel the game timer:  
Select OFF in step 2 above.  
TV front panel  
Using the front panel lock feature  
Lock the front panel buttons to prevent the buttons from being  
pressed accidentally (by children, for example). When the front panel  
lock is in ON, all control buttons on the TV front panel (except  
POWER) do not operate.  
Touch Focus  
MENU  
VOLUME  
CHANNEL  
EXIT TV/VIDEO  
Buttons to be locked  
To lock the front panel:  
1. From the LOCKS menu, select FRONT PANEL LOCK.  
2. Press x or • to highlight ON.  
POWER  
RECALL  
INFO  
TV/VIDEO  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
1
2
3
4
5
6
7
1
2
3
4
5
6
7
1
4
2
5
8
3
6
LOCKS  
8
9
8
9
V–CH I P  
ENABLE BLOCK I NG  
TV RAT I NG  
Number  
10  
11  
12  
13  
14  
15  
16  
17  
18  
10  
11  
12  
13  
14  
15  
16  
17  
18  
9
CHRTN  
7
MPAA RAT I NG  
BLOCK I NG OPT I ON  
CH LOCK  
+10  
V I DEO LOCK  
100  
0
ENT  
GAME TIMER  
FRONT RANEL LOCK  
NEW P I N CODE  
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
OFF  
ON/OFF  
FAV  
PIC  
1
2
3
4
5
6
7
8
9
SI  
ZE  
ORITE  
FAV  
If a button on the front panel is pressed, the message “Not  
Available” appears.  
MENU  
DVDMENU  
yzx •  
To unlock the front panel:  
ENTER  
EXIT  
FAV  
Highlight OFF in step 2 above, or press and hold the VOL x  
button on the TV for about 10 seconds until the message “Front  
Panel Lock: Off” appears on the screen.  
ENTER  
TV  
CBL/SAT CH  
VCR  
VOL  
DVD  
Changing the PIN code  
1. From the LOCKS menu, select NEW PIN CODE.  
2. Press the Number buttons (0-9) to enter a 4-digit code.  
The numbers you enter will replace the dashes in the display.  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
1
2
3
4
5
6
7
1
2
3
4
5
6
7
LOCKS  
8
9
8
9
V–CH I P  
ENABLE BLOCK I NG ON  
TV RAT I NG  
10  
11  
12  
13  
14  
15  
16  
17  
18  
10  
11  
12  
13  
14  
15  
16  
17  
18  
MPAA RAT I NG  
BLOCK I NG OPT I ON  
CH LOCK  
V I DEO LOCK  
V I DEO  
GAME TIMER  
OFF  
FRONT RANEL LOCK  
OFF  
NEW P I N CODE 2562  
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
1
2
3
4
5
6
7
8
9
3. Press ENTER.  
The new PIN code is now active.  
43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Adjusting the picture  
Selecting the picture mode  
Note:  
You can select your desired picture type from four picture modes:  
Sports, Standard, Movie, and Preference.  
If you select one of the factory-set picture  
modes (SPORTS, STANDARDS, or MOVIE)  
and then change a picture quality setting (for  
example, increase the contrast), the picture  
mode automatically changes to  
Mode  
Picture Quality  
Sports  
Standard  
Movie  
Bright and dynamic picture (factory setting)  
Standard picture setting (factory setting)  
Movie-like picture setting (factory setting)  
PREFERENCE in the Picture menu.  
To save your new picture quality settings, you  
must select SAVE NEW PREFERENCE (see  
page 45) before closing the Picture menu or  
the TV will return to the previous picture  
mode.  
Preference Your personal preference*  
*(see “Saving new preference” on page 45.)  
To select the picture mode:  
1. Press MENU, and then press x or • until the PICTURE menu  
appears.  
2. Press z or y to select MODE.  
x •zy  
3. Press x or • to highlight the mode you prefer.  
TV front panel  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
1
2
3
4
5
6
7
1
2
3
4
5
6
7
P I CTURE ANTENNA  
MODE  
8
9
8
9
TouchFocus  
EXIT TV/VIDEO  
10  
11  
12  
13  
14  
15  
16  
17  
18  
10  
11  
12  
13  
14  
15  
16  
17  
18  
MENU  
VOLUME  
CHANNEL  
SPORTS / STANDARD / MOVI E / PREFERENCE  
CONTRAST  
BR IGHTNESS  
COLOR  
8 0  
5 0  
5 0  
0
T I NT  
5 0  
SHARPNESS  
RESET  
SAVE NEW PREFERENCE  
ALS  
OFF  
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
MENU  
1
2
3
4
5
6
7
8
9
Adjusting the picture quality  
You can adjust the picture quality to your personal preferences,  
including the contrast, brightness, color, tint, sharpness, flesh tone,  
noise reduction and color temperature.  
POWER  
RECALL  
INFO  
TV/VIDEO  
1
4
2
5
8
3
6
Selection  
x Pressing •  
contrast  
brightness  
color  
tint  
sharpness  
lower  
darker  
paler  
reddish  
softer  
higher  
lighter  
deeper  
greenish  
sharper  
9
CHRTN  
7
+10  
100  
0
ENT  
FAV  
PIC  
SI  
ZE  
FAVORITE  
MENU  
yzx •  
MENU  
DVDMENU  
To adjust the picture quality:  
ENTER  
1. Press MENU, and then press x or • until the PICTURE menu  
EXIT  
FAV  
appears.  
TV  
CBL/SAT CH  
VCR  
VOL  
2. Press z or y until the item you want to adjust is highlighted.  
DVD  
3. Press x or • to adjust the level.  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
1
2
3
4
5
6
7
1
2
3
4
5
6
7
P I CTURE ANTENNA  
STANDARD  
8
9
8
9
MODE  
10  
11  
12  
13  
14  
15  
16  
17  
18  
10  
11  
12  
13  
14  
15  
16  
17  
18  
CONTRAST  
BR IGHTNESS  
COLOR  
7 5  
5 0  
5 0  
0
T I NT  
5 0  
SHARPNESS  
RESET  
SAVE  
NEW  
PREFERENCE  
OFF  
ALS  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
The PICTURE qualities you adjusted can be saved in the TV’s  
memory with the SAVE NEW PREFERENCE feature (see page 45).  
You can keep these settings or choose factory set options, as described  
under “Selecting the picture mode” above.  
44  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Saving your new preferences  
You can save the PICTURE qualities (contrast, brightness, color, tint,  
and sharpness) you adjusted in the picture preference mode.  
POWER  
RECALL  
INFO  
TV/VIDEO  
To save your new preferences:  
1
4
2
5
8
3
6
1. Press MENU, and then press x or • until the PICTURE menu  
appears.  
2. Press y or z to highlight SAVE NEW PREFERENCE.  
9
CHRTN  
7
+10  
3. Press x or •. When complete, the menu displays “DONE”.  
100  
0
ENT  
FAV  
PIC  
SI  
ZE  
FAVORITE  
MENU  
yzx •  
MENU  
DVDMENU  
P I CTURE ANTENNA  
MODE  
PREFERENCE  
FLESH TONE  
CableClear DNR  
COLOR  
OFF  
OFF  
ENTER  
EXIT  
FAV  
TEMPERATURE  
MEDIUM  
DISPLAY FORMAT 1080 i  
CONVERGENCE  
SAVE NEW PREFERENCE  
DONE  
TV  
CBL/SAT CH  
VCR  
VOL  
DVD  
The mode automatically change to PREFERENCE (see “Selecting the  
picture mode” on page 44).  
Using the ALS (ambient light sensor) feature  
The ALS feature automatically adjusts the picture contrast according  
to current lighting conditions. For example, when the room is dark,  
the ALS will automatically reduce the contrast (which reduces eye  
strain). ALS is activated when the ALS menu is set to ON.  
Note:  
To activate the ALS:  
Do not cover the ALS sensor on the front  
panel of the TV.  
1. Press MENU, and then press x or • until the PICTURE menu  
appears.  
2. Press y or z to highlight ALS.  
3. Press x or • to highlight ON. The CONTRAST setting changes  
to AUTO, and is not adjustable while the ALS feature is on.  
x •zy  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
TV front panel  
1
2
3
4
5
6
7
1
2
3
4
5
6
7
P I CTURE ANTENNA  
SPORTS  
8
9
8
9
MODE  
10  
11  
12  
13  
14  
15  
16  
17  
18  
o  
EXIT TV
10  
11  
12  
13  
14  
15  
16  
17  
18  
MENU  
VOLUME  
CHANNEL  
AUTO  
5 0  
5 0  
CONTRAST  
BR IGHTNESS  
COLOR  
T I NT  
0
5 0  
SHARPNESS  
RESET  
SAVE NEW PREFERENCE  
DONE  
ALS  
ON/ OFF  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22  
25 26 27 28 29 30 31 32 33 34 35  
MENU  
ALS sensor  
To deactivate the ALS:  
Highlight OFF in step 3 above.  
45  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the flesh tone feature  
This feature displays natural flesh tones by correcting the tint.  
To turn on the flesh tone feature:  
POWER  
RECALL  
INFO  
TV/VIDEO  
1. Press MENU, and then press x or • until the PICTURE menu  
1
4
2
5
8
3
6
appears.  
2. Press y or z to highlight FLESH TONE.  
9
CHRTN  
7
3. Press x or • to highlight ON.  
+10  
100  
0
ENT  
FAV  
PIC  
SI  
ZE  
FAVORITE  
P I CTURE ANTENNA  
MODE  
PREFERENCE  
MENU  
yzx •  
MENU  
DVDMENU  
FLESH TONE  
CableClear DNR  
COLOR  
ON/ OFF  
OFF  
TEMPERATURE  
DISPLAY FORMAT  
CONVERGENCE  
MEDIUM  
1080 i  
ENTER  
EXIT  
FAV  
SAVE NEW PREFERENCE  
TV  
CBL/SAT CH  
VCR  
VOL  
DVD  
Using the CableClear™ DNR feature  
This feature allows you to reduce visible interference in your TV  
picture. This is useful when receiving a broadcast with a weak signal  
(especially a Cable channel) or playing back a video cassette or disc  
damaged by repeated use.  
Note:  
The Cable Clear DNR feature is not available  
in DVI mode (will be set to OFF).  
To turn on CableClear DNR:  
1. Press MENU, and then press x or • until the PICTURE menu  
appears.  
2. Press y or z to highlight CableClear DNR.  
3. Press x or • to highlight AUTO.  
P I CTURE ANTENNA  
MODE  
PREFERENCE  
FLESH TONE  
CableClear DNR  
COLOR  
ON  
AUTO / OFF  
TEMPERATURE  
DISPLAY FORMAT  
CONVERGENCE  
MEDIUM  
1080 i  
SAVE NEW PREFERENCE  
To turn off CableClear DNR:  
Highlight OFF in step 3 above.  
Selecting the color temperature  
You can change the quality of the picture by selecting from three  
preset color temperatures: cool, medium, and warm.  
To select the color temperature:  
1. Press MENU, and then press x or • until the PICTURE menu  
appears.  
2. Press y or z to highlight COLOR TEMPERATURE.  
3. Press x or • to highlight the mode you prefer.  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
1
2
3
4
5
6
7
1
2
3
4
5
6
7
Mode  
Picture Quality  
cool  
blueish  
P I CTURE ANTENNA  
PREFERENCE  
8
9
8
9
medium neutral  
warm reddish  
MODE  
10  
11  
12  
13  
14  
15  
16  
17  
18  
10  
11  
12  
13  
FLESH TONE  
CableClaar DNR  
COLOR  
ON  
AUTO  
TEMPERATURE  
DISPLAY FORMAT  
CONVERGENCE  
COOL /MEDIUM /WARM  
1080 i  
14  
15  
16  
17  
18  
SAVE NEW PREFERENCE  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
46  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Selecting the display format (for 480p signals only)  
Use this feature to convert a 480p input signal to 540p or 1080i.  
To select the display format:  
Note:  
If you notice flicker in a 480p image, try  
setting the DISPLAY FORMAT feature to  
540p.  
1. Press MENU, and then press x or • until the PICTURE menu  
appears.  
2. Press y or z to highlight DISPLAY FORMAT.  
3. Press x or • to select 540p or 1080i as you desire.  
P I CTURE ANTENNA  
MODE  
MOVIE  
FLESH TONE  
CableClear DNR  
COLOR  
OFF  
AUTO  
TEMPERATURE  
DISPLAY FORMAT  
CONVERGENCE  
MEDIUM  
540P/1080 i  
SAVE NEW PREFERENCE  
Resetting your picture adjustments  
The RESET function adjusts the picture qualities to the following  
factory settings:  
POWER  
RECALL  
INFO  
TV/VIDEO  
1
4
2
5
8
3
6
Contrast ................ max (100) Color temperature........... cool  
Brightness ............ center (50) CableClear DNR ........... auto  
Color ................... center (50) Mode ........................... sports  
Tint ....................... center (0)  
9
CHRTN  
7
+10  
100  
0
ENT  
Sharpness ............. center (50)  
FAV  
PIC  
E
SI  
ZE  
FAVORITE  
To reset the picture adjustments:  
MENU  
yzx •  
MENU  
DVDMENU  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
1. Press MENU, and then  
press x or • until the  
3
4
5
6
7
ENTER  
N
EXIT  
C
FAV  
PICTURE menu appears.  
P I CTURE ANTENNA  
SPORTS  
8
9
MODE  
TV  
2. Press y or z to highlight  
CBL/SAT CH  
VCR  
VOL  
0
CONTRAST  
BR IGHTNESS  
COLOR  
1 0 0  
5 0  
5 0  
0
DVD  
RESET.  
3
4
5
6
7
8
T I NT  
5 0  
SHARPNESS  
RESET  
SAVE NEW PREFERENCE  
DONE  
3. Press x or •. The menu  
ALS  
ON  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
displays “DONE.”  
Selecting the cinema mode  
When you view a DVD movie (3-2 pulldown processed) from a  
DVD player connected to the ColorStream (component video)  
inputs on the TV, smoother and more natural motion can be  
obtained by setting the CINEMA MODE to FILM (auto).  
To set the CINEMA MODE to FILM (auto):  
1. Press MENU, and then press x or • until the THEATER menu  
appears.  
2. Press y or z to highlight CINEMA MODE.  
3. Press x or • to select FILM (auto).  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34  
1
2
3
4
5
6
7
2
35  
3
4
5
6
7
THEATER  
8
9
8
9
WOW  
SRS 3D  
FOCUS  
10  
11  
12  
13  
14  
15  
16  
17  
18  
10  
ON  
OFF  
ON OFF  
11  
12  
13  
14  
15  
16  
17  
18  
T r u B a s s  
P I CTURE S I ZE  
AUTO ASPECT  
P I CTURE SCROLL  
C I NEMA MODE  
OFF  
FILM / V I DEO  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
To set the CINEMA MODE to VIDEO (off):  
Press x or • to select VIDEO in step 3 above.  
47  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Selecting the video input source  
Note:  
Press TV/VIDEO on the remote control or TV to view a signal from  
another device connected to your TV, such as a VCR or video disc player  
(see illustrations below). You can select ANT 1, VIDEO 1, VIDEO 2,  
VIDEO 3, ColorStream HD1, ColorStream HD2, DVI, or ANT 2  
depending on which input jacks are used for connecting the devices (see  
“Connecting your TV” on page 8).  
• When ColorStream HD 1 or HD 2 is  
selected, the video OUT jack does not  
output a signal. To receive a video OUT  
signal, use a video or S-video IN  
connection instead of the ColorStream  
connection.  
• If you select ColorStream HD1 or HD2  
while the POP picture is active, the POP  
window will close.  
SOURCE SELECT ION  
SOURCE SELECT ION  
ANT  
1
0 : ANT  
1 : V IDEO  
2 : V IDEO  
V IDEO  
1
V IDEO  
V IDEO  
V IDEO  
1
2
3
1
2
3
3 :  
Col orSt ream HD1  
Col orSt ream HD2  
DVI  
4 : Col orSt ream HD1  
5 : Col orSt ream HD2  
:
:
6
7
DVI  
ANT  
ANT  
2
2
Please note the following regarding  
the DVI source selection:  
:
TV / V I DEO TO SELECT  
0
7 : TO SELECT  
This TV is not intended for connection  
to and should not be used with a PC  
(personal computer). See “Connecting  
a device to the DVI/HDCP input” on  
page 14 for details.  
Pressing TV/VIDEO on the remote  
control displays the current signal  
source (press TV/VIDEO again or  
0-7 to change)  
Pressing TV/VIDEO on the TV changes  
the current signal source  
Labeling the video input sources  
The video label feature allows you to label each input source for your  
TV from the following preset list of labels:  
TV front panel  
–
: Uses the default label name  
VCR : Video cassette recorder  
DVD : DVD video  
TouchFocus  
MENU  
VOLUME  
CHANNEL  
EXIT TV/VIDEO  
DTV : Digital TV set-top box  
SAT  
CBL  
HD  
: Satellite box  
: Cable box  
: DVI/HDCP device (see page 14.)  
TV/VIDEO  
To label the video input sources:  
1. Press MENU, and then press x or • until the CUSTOM menu  
appears.  
POWER  
RECALL  
INFO  
TV/VIDEO  
2. Press y or z to highlight VIDEO LABEL.  
TV/VIDEO  
1
4
7
2
5
8
3
6
CUSTOM  
T I MER  
00h00m  
ON  
9
CHRTN  
0h00m  
OFF  
SLEEP  
CC  
C2  
+10  
FAVOR I TE CH1  
FAVOR I TE CH2  
CH LABEL I NG  
V I DEO LABEL  
BACKGROUND  
100  
0
ENT  
FAV  
PIC  
SI  
ZE  
FAVORITE  
MENU  
yzx •  
MENU  
DVDMENU  
3. Press x or • to display the VIDEO LABEL menu.  
4. Press y or z to highlight the video source you want to label.  
5. Press x or • to select the desired label for that input source.  
ENTER  
EXIT  
EXIT  
FAV  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
TV  
CBL/SAT CH  
VCR  
VOL  
1
2
3
4
5
6
7
1
2
3
4
5
6
7
DVD  
CUSTOM  
8
9
8
9
V I DEO LABEL  
V I DEO1  
V I DEO2  
10  
11  
12  
13  
14  
15  
16  
17  
18  
10  
11  
12  
13  
14  
15  
16  
17  
18  
–
VCR/ DVD / DTV /SAT /CBL  
–
–
–
–
–
V I DEO3  
Note:  
Color Stream HD1  
Color Stream HD2  
DVI  
The HD (high-definition) label is available for  
CUSTOM MENU  
DVI mode only (see “Selecting the video  
input source” above, and “Connecting a  
device to the DVI/HDCP input” on page 14).  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
6. Finish labeling the other video sources as desired. To return to the  
previous menu, press y or z to highlight CUSTOM MENU,  
and then press x or •.  
7. To exit the menu, press EXIT.  
48  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the closed caption feature  
The closed caption feature has two options:  
• Captions—An on-screen display of the dialogue, narration, and  
sound effects of TV programs and videos that are closed  
captioned (usually marked as “CC” in TV listings).  
• Text—An on-screen display of information not related to the  
current program, such as weather or stock data (when provided  
by individual stations).  
To view captions or text:  
POWER  
RECALL  
INFO  
TV/VIDEO  
1. Tune the TV to the desired program.  
2. Press MENU, and then press x or • to display CUSTOM menu.  
3. Press y or z to highlight CC.  
1
4
2
5
8
3
6
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
1
2
3
4
5
6
7
1
2
3
4
5
6
7
9
CHRTN  
7
+10  
100  
0
ENT  
CUSTOM  
8
9
8
9
FAV  
PIC  
T I MER  
ON  
SLEEP  
SI  
ZE  
10  
11  
12  
13  
14  
15  
16  
17  
18  
10  
11  
12  
13  
14  
15  
16  
17  
18  
00h00m  
0h00m  
FAVORITE  
CC C1 / C2 / C3 / C4 / T1 / T2 / T3 / T4 /OFF  
FAVOR I TE CH1  
FAVOR I TE CH2  
CH LABEL I NG  
MENU  
yzx •  
MENU  
DVDMENU  
V I  
BACKGROUND  
LABEL  
DEO  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
ENTER  
EXIT  
FAV  
4. Press x or • to highlight the desired closed caption mode, as  
TV  
CBL/SAT CH  
VCR  
VOL  
follows:  
DVD  
• To view captions, highlight C1, C2, C3, or C4 (C1 displays  
translation of the primary language in your area).  
Note: If the program or video you selected is not closed captioned, no  
captions will display on the screen.  
Note:  
A closed caption signal may not display in the  
following situations:  
• when a videotape has been dubbed  
• when the signal reception is weak  
• when the signal reception is nonstandard  
Giant pandas eat leaves.  
• To view text, highlight T1, T2, T3, or T4.  
Note: If text is not available in your area, a black rectangle may appear on  
your screen. If this happens, turn the Closed Caption feature OFF.  
WORLD WEATHER  
Temps  
Current  
Weather  
Clear  
F
C
LONDON  
MOSCOW  
PARIS  
51  
57  
53  
66  
65  
11  
14  
12  
19  
18  
Cloudy  
Clear  
Cloudy  
Rain  
ROME  
TOKYO  
To turn off the Closed Caption feature:  
Highlight OFF in step 4.  
49  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting the ON timer  
To set the ON timer to turn on the TV automatically:  
POWER  
RECALL  
INFO  
TV/VIDEO  
1. Press MENU, and then press x or • until the CUSTOM menu  
POWER  
Number  
appears.  
1
4
2
5
8
3
6
2. Press y or z to highlight ON.  
3. After the number position starts to blink, press the Number  
buttons (0-9) to enter the length of time until the TV turns on  
automatically.  
9
CHRTN  
7
+10  
100  
0
ENT  
You can set the ON timer in 10-minute increments, up to  
12h00m.  
FAV  
PIC  
SI  
ZE  
FAVORITE  
4. Press ENTER to start the timer.  
MENU  
yzx •  
MENU  
DVDMENU  
ENTER  
EXIT  
FAV  
CUSTOM  
T I MER  
TV  
10h30m  
0h00m  
OFF  
ON  
SLEEP  
CC  
CBL/SAT CH  
VCR  
VOL  
ENTER  
SLEEP  
C2  
DVD  
FAVOR I TE CH1  
FAVOR I TE CH2  
CH LABEL I NG  
V I DEO LABEL  
BACKGROUND  
POP DIRECT CH MUTE  
SLEEP  
5. Press POWER to turn off the TV.  
The TV will turn on automatically at the time you set in the ON  
timer.  
Setting the sleep timer  
To set the sleep timer to turn the TV off automatically:  
Note :  
• When an instant power failure occurs, the  
ON timer and sleep timer settings may be  
cleared.  
1. Press SLEEP to set the length of time until the TV turns off.  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
1
2
3
4
5
6
7
1
2
3
4
5
6
7
• To display the amount of time left until the  
TV turns on or off automatically, press  
RECALL.  
8
9
8
9
10  
11  
12  
13  
14  
15  
16  
17  
18  
10  
11  
12  
13  
14  
15  
16  
17  
18  
T I MER  
0 h 00m  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
Every time you press the button, the time display will increase by  
10 minutes, up to 3 hours.  
0h00m → 0h10m → 0h20m  
2h50m → 3h00m → 0h00m  
To cancel the sleep timer:  
Press SLEEP until it is set to 0h00m.  
The timer can also be set using the on-screen menu:  
1. Press MENU, and then press x or • until the CUSTOM menu  
appears.  
2. Press y or z to highlight SLEEP.  
3. After the number position starts to blink, press the Number  
buttons (0-9) to enter the length of time until the TV turns off  
automatically.  
4. Press ENTER to start the timer.  
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
1
2
3
4
5
6
7
CUSTOM  
8
9
8
9
T I MER  
ON  
SLEEP  
10  
11  
12  
13  
14  
15  
16  
17  
18  
10  
11  
12  
13  
14  
15  
16  
17  
18  
00h00m  
2h00m  
C1  
CC  
FAVOR I TE CH1  
FAVOR I TE CH2  
CH LABEL I NG  
V I DEO LABEL  
BACKGROUND  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting the clock  
To set the clock:  
Note :  
1. Press MENU, and then press x or • until the SET UP menu  
If the TV’s power source is interrupted (the  
power cord is unplugged or a power failure  
occurs), the clock must be reset.  
appears.  
2. Press y or z to highlight CLOCK SET.  
3. After the number position starts to blink, press the Number  
buttons (0-9) to enter the correct time. The clock operates on a  
24-hour cycle.  
POWER  
RECALL  
INFO  
TV/VIDEO  
4. Press ENTER to start the clock.  
RECALL  
1
4
2
5
8
3
6
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
1
2
3
4
5
6
7
1
2
3
4
5
6
7
SET UP  
9
CHRTN  
7
8
9
8
9
LANGUAGE  
CLOCK SET  
ANT1 / 2  
ENGL I SH  
09 : 2 5  
ANT1  
+10  
10  
11  
12  
13  
14  
15  
16  
17  
18  
10  
11  
12  
13  
14  
15  
16  
17  
18  
100  
0
ENT  
TV / CABLE  
CH PROGRAM  
ADD / ERASE  
CABLE  
FAV  
ADD  
PIC  
QU I C K CONNECT GU I DE  
SI  
ZE  
FAVORITE  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
MENU  
yzx •  
MENU  
DVDMENU  
To display the time on-screen:  
Press RECALL.  
ENTER  
EXIT  
FAV  
ENTER  
TV  
CBL/SAT CH  
VCR  
VOL  
DVD  
51  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Adjusting the sound  
Muting the sound  
Press MUTE to temporarily reduce (1/2 MUTE) or turn off (MUTE)  
the sound. While the sound is off, the screen will display “1/2  
MUTE” or “MUTE” in the lower right corner. Every time you press  
the button, the mute mode will change in the following order.  
POWER  
RECALL  
INFO  
TV/VIDEO  
RECALL  
1
4
2
5
8
3
6
→ Normal → 1/2 MUTE → MUTE  
9
CHRTN  
7
When you select “MUTE” mode, the closed caption feature is  
automatically activated. To deactivate this feature, deactivate MUTE.  
This feature works only when the closed caption mode is set to OFF.  
See “Using the closed caption feature” on page 48 for more  
information.  
+10  
100  
0
ENT  
FAV  
PIC  
SI  
ZE  
FAVORITE  
MENU  
yzx •  
MENU  
DVDMENU  
Selecting stereo/SAP broadcasts  
ENTER  
EXIT  
FAV  
The multi-channel TV sound (MTS) feature allows you to listen to  
high-fidelity stereo sound while watching TV. MTS can also transmit  
a second audio program (SAP) containing a second language, music,  
or other audio information (when provided by individual stations).  
TV  
CBL/SAT CH  
VCR  
VOL  
DVD  
POP DIRECT CH MUTE  
SLEEP  
MUTE  
When the TV receives a stereo or SAP broadcast, the word STEREO  
or SAP appears on-screen every time the TV is turned on, the channel  
is changed, or the RECALL button is pressed.  
x •zy  
The MTS feature is not available when the TV is in VIDEO mode.  
To listen to stereo sound:  
TV front panel  
1. Press MENU, and then press x or • until the AUDIO menu  
appears.  
TouchFocus  
MENU  
VOLUME  
CHANNEL  
EXIT TV/VIDEO  
2. Press y or z to highlight MTS.  
3. Press x or • to highlight STEREO.  
MENU  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
1
2
3
4
5
6
7
1
2
3
4
5
6
7
AUDI O  
8
9
8
9
Note :  
MTS  
BASS  
TREBLE  
BALANCE  
RESET  
STEREO / SAP / MONO  
10  
11  
12  
13  
14  
15  
16  
17  
18  
10  
11  
12  
13  
14  
15  
16  
17  
18  
50  
50  
0
A second audio program (SAP) can be heard  
only on those TV stations that offer it.  
For example, a station might broadcast music  
as a second audio program. If you have SAP  
on, you will see the current program on the  
screen but hear music instead of the  
program’s normal audio.  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
You can leave your TV in STEREO mode because it will  
automatically output the type of sound being broadcast (stereo or  
monaural). The word “STEREO” or “SAP” displays in yellow in  
the menu when the TV receives the signal.  
However, if you have SAP on, and the  
station you are watching is not currently  
broadcasting a second audio program, the  
station’s normal audio will be output;  
however, occasionally there is no sound at all  
in this instance. If this happens, set the MTS  
feature to STEREO mode.  
If the stereo sound is noisy, select MONO to reduce the noise.  
To listen to SAP (if available):  
1. Press MENU, and then press x or • until the AUDIO menu  
appears.  
2. Press y or z to highlight MTS.  
3. Press x or • to highlight SAP. You will hear the station’s second  
audio program (if available) from the speakers, while viewing the  
original program’s picture (see note at right).  
52  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the WOW™ surround sound feature  
Note:  
WOW is the latest audio enhancement technology combined with  
SRS 3D and TruBass of SRS Labs individual technologies. The feature  
uses stereo signals from a TV broadcast or video input.  
If the broadcast is monaural, the SRS 3D  
effect does not work.  
To adjust the WOW feature:  
1. Select STEREO mode (See “Selecting stereo/SAP broadcasts” on  
page 52).  
2. Press MENU, and then press x or • until the THEATER menu  
appears.  
3. Press y or z to highlight the desired WOW feature you want to  
adjust, then press x or • to adjust the item.  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34  
1
2
3
4
5
6
7
2
35  
3
4
5
6
7
POWER  
RECALL  
INFO  
TV/VIDEO  
THEATER  
8
9
8
9
WOW  
SRS 3D  
FOCUS  
10  
11  
12  
13  
14  
15  
16  
17  
18  
10  
1
4
2
5
8
3
6
ON OFF  
/
11  
12  
13  
14  
15  
16  
17  
18  
OFF  
ON HIGH  
T r u B a s s  
P I CTURE S I ZE  
AUTO ASPECT  
P I CTURE SCROLL  
C I NEMA MODE  
OFF  
FILM V I DEO  
9
CHRTN  
7
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
+10  
100  
0
ENT  
• SRS 3D — To turn on or off the surround sound effect.  
• FOCUS — To turn on or off the vocal enphasis effect.  
• TruBass — To select your desired bass expansion level (HIGH,  
LOW or OFF).  
FAV  
PIC  
SI  
ZE  
FAVORITE  
MENU  
yzx •  
MENU  
DVDMENU  
ENTER  
EXIT  
FAV  
Adjusting the sound quality  
You can change the quality of your TV’s sound by adjusting the bass,  
treble, and balance.  
TV  
CBL/SAT CH  
VCR  
VOL  
DVD  
To adjust the sound quality:  
1. Press MENU, and then press x or • until the AUDIO menu  
appears.  
2. Press y or z to highlight the item you want to adjust.  
AUDI O  
MTS  
STEREO / SAP / MONO  
BASS  
50  
50  
0
TREBLE  
BALANCE  
RESET  
3. Press x or • to adjust the level.  
• x makes the sound quality weaker or decreases the balance in the  
right channel, depending on the item selected.  
• • makes the sound quality stronger or decreases the balance in  
the left channel, depending on the item selected.  
________  
SRS WOW, SRS and  
symbol are trademarks of SRS Labs, Inc.  
SRS WOW technology is incorporated under license from SRS Labs, Inc.  
53  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Resetting your audio adjustments  
The RESET function returns the audio adjustments to the following  
factory settings:  
POWER  
RECALL  
INFO  
TV/VIDEO  
Bass.................. center (50)  
Treble............... center (50)  
Balance ............ center (0)  
1
4
2
5
8
3
6
9
CHRTN  
7
To reset the audio adjustments:  
+10  
100  
0
ENT  
1. Press MENU, and then press x or • until the AUDIO menu  
FAV  
appears.  
PIC  
SI  
ZE  
FAVORITE  
2. Press y or z to highlight RESET.  
MENU  
yzx •  
MENU  
DVDMENU  
3. Press x or •. The menu displays “DONE”.  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
ENTER  
1
2
3
4
5
6
7
1
2
3
4
5
6
7
EXIT  
FAV  
TV  
CBL/SAT CH  
VCR  
VOL  
AUDI O  
8
9
8
9
DVD  
MTS  
BASS  
STEREO  
10  
11  
12  
13  
14  
15  
16  
17  
18  
10  
11  
12  
13  
14  
15  
16  
17  
18  
50  
50  
0
TREBLE  
BALANCE  
RESET  
DONE  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
Note:  
While in the SBS OFF mode, if the SBS level  
is adjusted, the SBS is automatically set ON.  
Using the sub-bass system (SBS)  
The sub-bass system allows you to enhance bass performance, even  
when the sound volume is low.  
To turn on the SBS:  
1. Press MENU, and then press x or • until the AUDIO menu  
appears.  
2. Press y or z to highlight SBS.  
3. Press x or • to highlight ON.  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
1
2
3
4
5
6
7
1
2
3
4
5
6
7
AUDI O  
8
9
8
9
SBS  
ON/ OFF  
1 0 0  
ON  
MA I N  
10  
11  
12  
13  
14  
15  
16  
17  
18  
10  
11  
12  
13  
14  
15  
16  
17  
18  
SBS LEVEL  
SPEAKERS  
AUDI O OUT  
STABLE SOUND OFF  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
To adjust the SBS level:  
4. Press y or z to highlight SBS LEVEL.  
5. Press x or • to adjust the SBS level.  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
1
2
3
4
5
6
7
1
2
3
4
5
6
7
AUDI O  
8
9
8
9
SBS  
ON  
8 0  
10  
11  
12  
13  
14  
15  
16  
17  
18  
10  
11  
12  
13  
14  
15  
16  
17  
18  
SBS LEVEL  
SPEAKERS  
AUDI O OUT  
ON  
MA I N  
STABLE SOUND OFF  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
To turn off the SBS:  
Highlight OFF in step 3 above.  
54  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Turning off the built-in speakers  
Note:  
Use this feature to turn the TV speakers off when you connect an  
audio system (See “Connecting an audio system” on page 15).  
Make sure the volume control of your audio  
amplifier is set to a moderate listening level.  
To turn off the built-in speakers:  
1. Press MENU, then press x or • until AUDIO menu appears.  
2. Press y or z to highlight SPEAKERS.  
3. Press x or • to highlight OFF.  
POWER  
RECALL  
INFO  
TV/VIDEO  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
1
2
3
4
5
6
7
1
2
3
4
5
6
7
1
4
2
5
8
3
6
AUDI O  
8
9
8
9
9
CHRTN  
7
SBS  
ON  
8 0  
10  
11  
12  
13  
14  
15  
16  
17  
18  
10  
11  
12  
13  
14  
15  
16  
17  
18  
SBS LEVEL  
SPEAKERS  
AUDI O OUT  
+10  
ON/ OFF  
MA I N  
100  
0
ENT  
STABLE SOUND OFF  
FAV  
PIC  
SI  
ZE  
FAVORITE  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
MENU  
yzx •  
MENU  
DVDMENU  
To turn on the built-in speakers:  
Highlight ON in step 3 above.  
ENTER  
EXIT  
FAV  
TV  
CBL/SAT CH  
VCR  
VOL  
DVD  
Selecting the Audio OUT sound  
This feature allows you to select the sound source (MAIN or POP)  
that is output from the Audio OUT jacks (See “Connecting two  
VCRs” on page 13).  
Note:  
This is useful when amplifying or recording the POP sound with  
external equipment while hearing the sound of the main picture  
through the built-in speakers.  
When the POP double-window is on-screen,  
the sound of the main program is output to  
the AUDIO OUT jacks, even if POP is  
selected in the AUDIO OUT menu.  
To select the Audio OUT sound:  
1. Press MENU, and then press x or • until the AUDIO menu  
The sound of the main program is always  
output from the TV’s speakers, regardless of  
the AUDIO OUT setting.  
appears.  
2. Press y or z to highlight AUDIO OUT.  
3. Press x or • to select MAIN or POP.  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
1
2
3
4
5
6
7
1
2
3
4
5
6
7
AUDI O  
8
9
8
9
SBS  
ON  
1 0 0  
ON  
10  
11  
12  
13  
14  
15  
16  
17  
18  
10  
11  
12  
13  
14  
15  
16  
17  
18  
SBS LEVEL  
SPEAKERS  
AUDI O OUT  
MAIN / POP  
STABLE SOUND OFF  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
• MAIN: Outputs the sound of the main program to the AUDIO  
OUT jacks.  
• POP: Outputs the sound of the POP program to the AUDIO  
OUT jacks.  
55  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the StableSound® feature  
When the signal source is changed, the StableSound feature limits the  
highest volume level to prevent extreme changes in volume (for  
example, to prevent the sudden increase in volume that often happens  
when a TV program switches to a commercial).  
POWER  
RECALL  
INFO  
TV/VIDEO  
1
4
2
5
8
3
6
To turn on the StableSound feature:  
1. Press MENU, and then press x or • until the AUDIO menu  
9
CHRTN  
7
appears.  
+10  
100  
0
ENT  
2. Press y or z to highlight STABLE SOUND.  
FAV  
PIC  
SI  
ZE  
3. Press x or • to select ON.  
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
FAVORITE  
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
1
2
3
4
5
6
7
MENU  
yzx •  
MENU  
DVDMENU  
ENTER  
AUDI O  
8
9
8
9
EXIT  
FAV  
SBS  
ON  
8 0  
ON  
POP  
10  
11  
12  
13  
14  
15  
16  
17  
18  
10  
11  
12  
13  
14  
15  
16  
17  
18  
SBS LEVEL  
SPEAKERS  
AUDI O OUT  
TV  
STABLE SOUND ON /OFF  
CBL/SAT CH  
VCR  
VOL  
DVD  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
To turn off the StableSound feature:  
Highlight OFF in step 3 above.  
Selecting the background of the menu display  
You can change the background of the menu display by selecting from  
two preset types: shaded and solid (gray).  
POWER  
RECALL  
TV/VIDEO  
INFO  
RECALL  
To select the background:  
1
4
7
2
3
6
1. Press MENU, and then press x or • until the CUSTOM menu  
5
8
appears.  
2. Press y or z to highlight BACKGROUND.  
9
CHRTN  
+10  
3. Press x or • to select either a SHADED or SOLID background.  
100  
0
ENT  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
FAV  
1
2
3
4
5
6
7
1
2
3
4
5
6
7
PIC  
SI  
ZE  
FAVORITE  
MENU  
yzx •  
MENU  
DVDMENU  
CUSTOM  
8
9
8
9
T I MER  
ON  
SLEEP  
10  
11  
12  
13  
14  
15  
16  
17  
18  
10  
11  
12  
13  
14  
15  
16  
17  
18  
00h00m  
0h00m  
C 1  
ENTER  
CC  
FAVOR I TE CH1  
FAVOR I TE CH2  
CH LABEL I NG  
V I DEO LABEL  
BACKGROUND  
EXIT  
FAV  
SHADED / SOL I D  
TV  
CBL/SAT CH  
VCR  
VOL  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35  
DVD  
Displaying on-screen information  
Press RECALL to display the following information on-screen:  
• Antenna mode (when in TV mode)  
• Channel number or VIDEO mode selected  
• Time (if set)  
• Remaining time of ON/SLEEP timer (if set)  
• Channel label (if set)  
• Stereo or SAP audio status  
• V-CHIP rating status  
• Picture size (when in ColorStream mode)  
33 34 35  
33 34 35  
1
2
1
2
3
4
5
6
7
STEREO  
SAP  
STEREO  
3
4
5
6
7
TV – PG  
ON T I MER  
SLEEP T I MER  
L
V
TV – PG  
ON T I MER  
SLEEP T I MER  
L
V
12h34m  
1h23m  
12h34m  
1h23m  
8
9
8
9
10  
11  
12  
13  
14  
15  
16  
17  
18  
10  
11  
12  
13  
14  
15  
16  
17  
18  
ANT  
1
FULL  
ABCD  
THEATER WI DE 1  
DVD  
ColorStream  
HD1  
CLOCK  
9
: 2 5  
CABLE  
6
CLOCK 12 : 3 4  
33 34 35  
33 34 35  
56  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Viewing the demo mode  
The demo mode automatically demonstrates several of your TV’s  
features. This function is provided for demonstration purposes only.  
To start the demo:  
Press and hold MENU on the TV front panel for 4 seconds.  
To stop the demo:  
Press RECALL, EXIT, or POWER.  
Understanding the auto power off feature  
The TV will automatically turn itself off after approximately 15  
minutes if it is tuned to a vacant channel or a station that completes  
its broadcast for the day. This feature does not work in VIDEO mode.  
Understanding the last mode memory feature  
If the power is cut off while you are viewing the TV, the Last Mode  
Memory feature turns the TV on automatically when the power is  
resupplied.  
If the power is going to be off for a long time and you are going to be  
away from your TV, unplug the power cord to prevent the TV from  
turning on in your absence.  
57  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Appendix  
Specifications  
Television System  
NTSC standard  
Dimensions  
46H83: Width  
43-3/8 inches (1102 mm)  
40 inches (1029 mm)  
21-7/8 inches (556 mm)  
47-9/16 inches (1208 mm)  
50 inches (1283 mm)  
22 inches (572 mm)  
52-3/4 inches (1340 mm)  
55 inches (1416 mm)  
23-7/8 inches (606 mm)  
59-7/8 inches (1521 mm)  
59-7/8 inches (1521 mm)  
26 inches (668 mm)  
Height  
Depth  
51H83: Width  
Height  
Depth  
57H83: Width  
Height  
Depth  
65H83: Width  
Height  
Channel Coverage  
VHF: 2 through 13  
UHF: 14 through 69  
Cable TV: Mid band (A-8 through A-1, A through I)  
Super band (J through W)  
Hyper band (AA through ZZ, AAA, BBB)  
Ultra band (65 through 94, 100 through 125)  
Power Source  
120 V AC, 60 Hz  
Depth  
Power Consumption  
190 W (average)  
Mass  
46H83: 150 lbs (68.0 kg)  
51H83: 169 lbs (76.6 kg)  
57H83: 204 lbs (92.5 kg)  
Audio Power  
20 W + 20 W  
65H83: 240 lbs (108.8 kg)  
Speaker Type  
Supplied Accessories  
Remote Control with 2 size “AA” alkaline batteries  
46H83: Two 4-3/4 inches (12 cm) round  
51H83: Two 6-5/16 inches (16 cm) round  
57H83: Two 6-5/16 inches (16 cm) round  
65H83: Two 6-5/16 inches (16 cm) round  
Optional TV Stand  
46H83: ST4663  
Video/Audio Terminals  
Design and specifications are subject to change without notice.  
S-VIDEO INPUT  
Y : 1 V(p-p), 75 ohm, negative sync.  
C : 0.286 V(p-p) (burst signal), 75 ohm  
VIDEO/AUDIO INPUT  
VIDEO: 1 V(p-p), 75 ohm, negative sync.  
AUDIO: 150 mV(rms) (30% modulation equivalent,  
47 k ohm)  
ColorStream® (component video) INPUT  
Y : 1V(p-p), 75 ohm  
PR: 0.7 V(p-p), 75 ohm  
PB: 0.7 V(p-p), 75 ohm  
AUDIO: 150 mV(rms), 47 k ohm  
VIDEO/AUDIO OUTPUT  
VIDEO: 1 V(p-p), 75 ohm, negative sync.  
AUDIO: 150 mV(rms) (30% modulation equivalent,  
4.7 k ohm)  
VARIABLE AUDIO OUTPUT  
0–300 mV(rms) (30% modulation equivalent, 4.7 k ohm)  
AUDIO CENTER CHANNEL INPUT  
300 mV(rms) (30% modulation equivalent, 10 k ohm)  
DVI/HDCP INPUT  
HDCP compliant  
E-EDID* 1.3 compliant  
DVI-D uncompressed, high-speed, digital single-link  
connection  
Suggested scan rates: 1080i, 480p, 480i  
_________  
* E-EDID = Enhanced-Extended Display Identification  
58  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Troubleshooting  
Before calling a service technician, please check the following table for a possible cause of the problem and  
some solutions.  
Problem  
Solution  
TV will not turn on  
• Make sure the power cord is plugged in, then press POWER.  
• The remote control batteries may be dead. Replace the batteries.  
No picture, no sound  
No sound, picture OK  
• Check the antenna/cable connections.  
• The sound may be muted. Press VOLUME.  
• The station may have broadcast difficulties. Try another channel.  
• Check that the SPEAKERS function in AUDIO menu is set properly.  
• Check that the AUDIO CENTER CHANNEL switch is set  
properly.  
Poor picture, sound OK  
• Check the antenna connections.  
• The station may have broadcast difficulties. Try another channel.  
• Adjust the PICTURE menu.  
Poor reception of broadcast channels  
• The station may have broadcast difficulties. Try another channel.  
• Check the antenna connections.  
• If you are using a VCR, make sure the TV/VCR button is set  
correctly.  
Cannot receive above channel 13  
• Make sure the TV/CABLE switch is set to the mode that  
corresponds with the signal source type (cable company or outside  
antenna).  
Black box appears on the screen  
Unable to select a certain channel  
Multiple images  
• The closed caption feature may be set to one of the Text modes (T1,  
T2, T3, or T4). Turn closed captioning OFF.  
• The channel may be locked out with the CH LOCK feature, or  
erased with the ADD/ERASE feature.  
• The station may have broadcast difficulties. Try another channel.  
• Antenna reception may be poor. Use a highly directional outdoor  
antenna.  
Poor color or no color  
• The station may have broadcast difficulties. Try another channel.  
• Adjust the TINT and/or COLOR in the PICTURE menu.  
No stereo or SAP sound from a  
known MTS broadcast  
• Make sure the MTS feature is set properly.  
The front panel buttons do not operate • Check the FRONT PANEL LOCK feature.  
The remote control does not operate  
• Check whether the appropriate device mode is selected.  
• Remove all obstructions between the remote control and the remote  
control sensor in the TV.  
• The remote control batteries may be dead. Replace the batteries.  
Cannot access signal input sources  
(Video1, Video2, Video3,  
• Check the VIDEO LOCK feature.  
ColorStream HD1/HD2, DVI/HDCP)  
and/or Channels 3 and 4.  
59  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Limited United States Warranty  
for 27'' FST PURE® and All Larger Television Models  
Toshiba America Consumer Products, L.L.C. (“TACP”) makes the  
(4) Labor service charges for set installation, setup, adjustment  
of customer controls, and installation or repair of antenna  
systems are not covered by these warranties. Reception  
problems caused by inadequate antenna systems are your  
responsibility.  
following limited warranties to original consumers in the United  
States. THESE LIMITED WARRANTIES EXTEND TO THE  
ORIGINAL CONSUMER PURCHASER OR ANY PERSON  
RECEIVING THIS TELEVISION AS A GIFT FROM THE  
ORIGINAL CONSUMER PURCHASER AND TO NO OTHER  
PURCHASER OR TRANSFEREE.  
(5) Warranties extend only to defects in materials or  
workmanship as limited above and do not extend to any  
television or parts that have been lost or discarded by you or  
to damage to television or parts caused by misuse, accident,  
Acts of God (such as lightning or fluctuations in electric  
power), improper installation, improper maintenance, or use  
in violation of instructions furnished by TACP; or to units that  
have been modified or had the serial number removed,  
altered, defaced, or rendered illegible.  
PRODUCTS PURCHASED IN THE U.S.A. AND USED IN  
CANADA ARE NOT COVERED BY THESE WARRANTIES.  
PRODUCTS PURCHASED IN CANADA AND USED IN THE  
U.S.A. ARE NOT COVERED BY THESE WARRANTIES.  
Limited One (1) Year Warranty on Parts and Labor*  
TACP warrants this television and its parts against defects in  
materials or workmanship for a period of one (1) year after the  
date of original retail purchase. DURING THIS PERIOD,  
TACP WILL, AT TACP’S OPTION, REPAIR OR REPLACE A  
DEFECTIVE PART WITH A NEW OR REFURBISHED PART  
WITHOUT CHARGE TO YOU FOR PARTS OR LABOR. TACP  
Authorized Service Station personnel will come to your home  
when warranty service is required. Depending on the type of  
repair required, either the service will be performed in your home  
or the set will be taken to the TACP Authorized Service Station  
for repair and returned to your home at no cost to you.  
How to Obtain Warranty Services  
If, after following all of the operating instructions in this manual  
and checking the “Troubleshooting” section, you find that service  
is needed:  
(1) Visit TACP’s web site at www.toshiba.com/tacp or  
call toll free 1-800-631-3811 to find the nearest TACP  
Authorized Service Station.  
(2) Present your bill of sale or other proof of purchase to the  
Authorized Service Station. Authorized TACP Service Station  
personnel will come to your home when warranty service is  
required. Depending on the type of repair required, either  
the service will be performed in your home or the set will be  
taken to the Authorized Service Station for repair and  
returned to your home at no cost to you.  
Limited Two (2) Year Warranty on Picture Tube*  
TACP further warrants the picture tube in this television against  
defects in materials or workmanship for a period of two (2)  
years after the date of original retail purchase. DURING THIS  
PERIOD, TACP WILL, AT TACP’S OPTION, REPAIR OR  
REPLACE A DEFECTIVE PICTURE TUBE WITH A NEW OR  
REFURBISHED PICTURE TUBE WITHOUT CHARGE TO YOU,  
EXCEPT THAT, IF A DEFECTIVE PICTURE TUBE IS REPAIRED  
OR REPLACED AFTER ONE (1) YEAR FROM THE DATE OF  
THE ORIGINAL RETAIL PURCHASE, YOU PAY LABOR  
CHARGES INVOLVED IN THE REPAIR OR REPLACEMENT.  
For additional information, visit TACP’s web site:  
www.toshiba.com/tacp  
.
ALL WARRANTIES IMPLIED BY THE LAW OF ANY STATE  
OF THE U.S.A., INCLUDING THE IMPLIED WARRANTIES OF  
MERCHANTABILITY AND FITNESS FOR A PARTICULAR  
PURPOSE, ARE EXPRESSLY LIMITED TO THE DURATION  
OF THE LIMITED WARRANTIES SET FORTH ABOVE. WITH  
THE EXCEPTION OF ANY WARRANTIES IMPLIED BY THE  
LAW OF ANY STATE OF THE U.S.A. AS HEREBY LIMITED,  
THE FOREGOING WARRANTY IS EXCLUSIVE AND IN  
LIEU OF ALL OTHER WARRANTIES, GUARANTEES,  
AGREEMENTS, AND SIMILAR OBLIGATIONS OF TACP  
WITH RESPECT TO THE REPAIR OR REPLACEMENT OF  
ANY PARTS. IN NO EVENT SHALL TACP BE LIABLE FOR  
CONSEQUENTIAL OR INCIDENTAL DAMAGES.  
Rental Units  
The warranty for rental units begins with the date of first rental or  
thirty (30) days from the date of shipment to the rental firm,  
whichever comes first.  
*Commercial Units  
Televisions sold and used for commercial purposes have a limited  
ninety (90) day warranty for all parts, labor, and picture tubes.  
No person, agent, distributor, dealer, or company is authorized  
to change, modify, or extend the terms of these warranties in  
any manner whatsoever. The time within which action must be  
commenced to enforce any obligation of TACP arising under this  
warranty or under any law of the United States or of any state  
thereof is hereby limited to 90 days from the date you discover,  
or should have discovered, the defect. This limitation does not  
apply to implied warranties arising under the law of any state  
of the U.S.A.  
Owner’s Manual and Product Registration Card  
Read this owner’s manual thoroughly before operating this  
television. Complete and mail the enclosed product registration  
card within ten days after you, or the person who has given you  
this product as a gift, purchased this television. Returning the  
product registration card will enable TACP to provide you with  
better customer service and improved product support. Failure  
to return the product registration card will not affect your rights  
under this warranty.  
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS,  
AND YOU MAY ALSO HAVE OTHER RIGHTS, WHICH MAY  
VARY FROM STATE TO STATE IN THE U.S.A. SOME STATES  
OF THE U.S.A. DO NOT ALLOW LIMITATIONS ON THE  
DURATION OF AN IMPLIED WARRANTY, LIMITATIONS ON  
THE TIME WITHIN WHICH AN ACTION MAY BE BROUGHT,  
OR THE EXCLUSION OR LIMITATION OF INCIDENTAL OR  
CONSEQUENTIAL DAMAGES; THEREFORE, THE ABOVE  
LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU  
UNDER SUCH CIRCUMSTANCES.  
Your Responsibility  
THE ABOVE WARRANTIES ARE SUBJECT TO THE  
FOLLOWING CONDITIONS:  
(1) You must provide your bill of sale or other proof of purchase.  
(2) All warranty servicing of this television must be made by an  
Authorized TACP Service Station.  
(3) The warranties from TACP are effective only if the television is  
purchased and operated in the U.S.A. or Puerto Rico.  
FST PURE® is a registered trademark of Toshiba America Consumer Products, L.L.C.  
0104  
60  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Limited Canada Warranty  
If you purchased your TV in Canada,  
register it online at www.toshiba.ca  
for 27'' FST PURE® and All Larger Television Models  
Toshiba of Canada Limited (“TCL”) makes the following limited  
warranties to original consumers in Canada.  
problems caused by inadequate antenna systems are your  
responsibility.  
(5) Warranties extend only to defects in materials or  
workmanship as limited above and do not extend to any  
television or parts that have been lost or discarded by you or  
to damage to television or parts caused by misuse, accident,  
Acts of God (such as lightning or fluctuations in electric  
power), improper installation, improper maintenance, or use  
in violation of instructions furnished by TCL; or to units that  
have been modified or had the serial number removed,  
altered, defaced, or rendered illegible.  
THESE LIMITED WARRANTIES EXTEND TO THE ORIGINAL  
CONSUMER PURCHASER OR ANY PERSON RECEIVING  
THIS TELEVISION AS A GIFT FROM THE ORIGINAL  
CONSUMER PURCHASER AND TO NO OTHER  
PURCHASER OR TRANSFEREE.  
PRODUCTS PURCHASED IN THE U.S.A. AND USED IN  
CANADA ARE NOT COVERED BY THESE WARRANTIES.  
PRODUCTS PURCHASED IN CANADA AND USED IN THE  
U.S.A. ARE NOT COVERED BY THESE WARRANTIES.  
How to Obtain Warranty Services  
If, after following all of the operating instructions in this manual  
and checking the “Troubleshooting” section, you find that service  
is needed:  
Limited One (1) Year Warranty on Parts and Labor*  
TCL warrants this television and its parts against defects in  
materials or workmanship for a period of one (1) year after the  
date of original retail purchase. DURING THIS PERIOD, TCL  
WILL, AT TCL’S OPTION, REPAIR OR REPLACE A DEFECTIVE  
PART WITH A NEW OR REFURBISHED PART WITHOUT  
CHARGE TO YOU FOR PARTS OR LABOR. TCL Authorized  
Service Depot personnel will come to your home when warranty  
service is required. Depending on the type of repair required,  
either the service will be performed in your home or the set will  
be taken to the TCL Authorized Service Depot for repair and  
returned to your home at no cost to you. IN-HOME SERVICE  
ONLY APPLIES WITHIN 100 KILOMETERS OF AN  
(1) To find the nearest TCL Authorized Service Depot, visit TCL’s  
web site: www.toshiba.ca.  
(2) Present your bill of sale or other proof of purchase to the  
Authorized Service Depot. Authorized TCL Service Depot  
personnel will come to your home when warranty service is  
required. Depending on the type of repair required, either  
the service will be performed in your home or the set will be  
taken to the Authorized Service Depot for repair and  
returned to your home at no cost to you. IN-HOME  
SERVICE ONLY APPLIES WITHIN 100 KILOMETERS OF  
AN AUTHORIZED TCL SERVICE DEPOT.  
AUTHORIZED TCL SERVICE DEPOT.  
Limited Two (2) Year Warranty on Picture Tube*  
For additional information, visit TCL’s web site:  
www.toshiba.ca  
TCL further warrants the picture tube in this television against  
defects in materials or workmanship for a period of two (2) years  
after the date of original retail purchase. DURING THIS  
PERIOD, TCL WILL, AT TCL’S OPTION, REPAIR OR REPLACE  
A DEFECTIVE PICTURE TUBE WITH A NEW OR  
REFURBISHED PICTURE TUBE WITHOUT CHARGE TO YOU,  
EXCEPT THAT, IF A DEFECTIVE PICTURE TUBE IS REPAIRED  
OR REPLACED AFTER ONE (1) YEAR FROM THE DATE OF  
THE ORIGINAL RETAIL PURCHASE, YOU PAY LABOR  
CHARGES INVOLVED IN THE REPAIR OR REPLACEMENT.  
ALL WARRANTIES IMPLIED BY THE LAW OF ANY  
PROVINCE OF CANADA, INCLUDING THE IMPLIED  
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR  
A PARTICULAR PURPOSE, ARE EXPRESSLY LIMITED TO  
THE DURATION OF THE LIMITED WARRANTIES SET FORTH  
ABOVE. WITH THE EXCEPTION OF ANY WARRANTIES  
IMPLIED BY THE LAW OF ANY PROVINCE OF CANADA AS  
HEREBY LIMITED, THE FOREGOING WARRANTY IS  
EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES,  
GUARANTEES, AGREEMENTS, AND SIMILAR  
OBLIGATIONS OF TCL WITH RESPECT TO THE REPAIR OR  
REPLACEMENT OF ANY PARTS. IN NO EVENT SHALL TCL  
BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL  
DAMAGES.  
Rental Units  
The warranty for rental units begins with the date of first rental or  
thirty (30) days from the date of shipment to the rental firm,  
whichever comes first.  
*Commercial Units  
Televisions sold and used for commercial purposes have a limited  
ninety (90) day warranty for all parts, labor, and picture tubes.  
No person, agent, distributor, dealer, or company is authorized  
to change, modify, or extend the terms of these warranties in  
any manner whatsoever. The time within which action must be  
commenced to enforce any obligation of TCL arising under this  
warranty or under any law of Canada or of any province thereof,  
is hereby limited to 90 days from the date you discover, or should  
have discovered, the defect. This limitation does not apply to  
implied warranties arising under the law of any province of  
Canada.  
Owner’s Manual  
Read this owner’s manual thoroughly before operating this  
television.  
Your Responsibility  
THE ABOVE WARRANTIES ARE SUBJECT TO THE  
FOLLOWING CONDITIONS:  
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS,  
AND YOU MAY ALSO HAVE OTHER RIGHTS, WHICH MAY  
VARY FROM PROVINCE TO PROVINCE IN CANADA. SOME  
PROVINCES OF CANADA DO NOT ALLOW LIMITATIONS  
ON THE DURATION OF AN IMPLIED WARRANTY, LIMITA-  
TIONS ON THE TIME WITHIN WHICH AN ACTION MAY  
BE BROUGHT, OR THE EXCLUSION OR LIMITATION OF  
INCIDENTAL OR CONSEQUENTIAL DAMAGES; THERE-  
FORE, THE ABOVE LIMITATIONS OR EXCLUSIONS MAY  
NOT APPLY TO YOU UNDER SUCH CIRCUMSTANCES.  
(1) You must provide your bill of sale or other proof of purchase.  
(2) All warranty servicing of this television must be made by an  
Authorized TCL Service Depot.  
(3) The warranties from TCL are effective only if the television is  
purchased in Canada from an authorized TCL dealer and  
operated in Canada.  
(4) Labor service charges for set installation, setup, adjustment  
of customer controls, and installation or repair of antenna  
systems are not covered by these warranties. Reception  
FST PURE® is a registered trademark of Toshiba America Consumer Products, L.L.C.  
0104  
61  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Index  
O P  
A
ON-timer.................................................................................50  
Picture adjustments  
A/V cables (standard) ......................................................... 8  
A/V receiver connection ...................................................15  
Ambient light sensor (ALS).............................................45  
ANT 1/2 ...................................................................................22  
Antenna cables (coaxial) ................................................... 8  
AUDIO OUT sound, selecting ........................................55  
Audio system connection.................................................15  
Auto aspect............................................................................33  
Auto convergence ...............................................................25  
Auto favorite ................................................................... 37, 41  
Auto power off......................................................................57  
COLOR TEMPERATURE ..............................................46  
FLESH TONE ....................................................................46  
Picture mode ....................................................................44  
Picture quality ..................................................................44  
Picture-out-picture (POP)  
CH SCAN button ........................................................... 36  
FREEZE button ................................................................35  
POP CH yz buttons .................................................... 34  
POP DIRECT CH button ...............................................34  
SOURCE button ............................................................. 34  
SPLIT button .................................................................... 34  
SWAP button ....................................................................35  
Picture scroll..........................................................................32  
Picture size selection .........................................................30  
POP (also see “Picture-out-picture”) ..........................34  
B
BACKGROUND selection ................................................56  
Back of the TV ........................................................................ 7  
C
CableClear™ DNR ...............................................................46  
Cable converter box connection ..................................... 9  
Camcorder connection......................................................13  
CH yz buttons ....................................................................25  
CH LABELING ......................................................................29  
CH LOCK.................................................................................41  
CH RTN button .....................................................................27  
Channel Number buttons ................................................25  
Channel programming  
Q R  
Quick connect guide..........................................................24  
RECALL button ....................................................................56  
Remote control  
Battery installation .........................................................16  
Learning about the buttons ........................................20  
Programming....................................................................17  
RESET ............................................................................... 47, 54  
ADD/ERASE .....................................................................23  
Automatic programming .............................................23  
TV/CABLE selection ......................................................23  
Cinema mode........................................................................47  
Clock, setting ........................................................................51  
Closed caption......................................................................49  
Color temperature ...............................................................46  
ColorStream (component) cables................................... 8  
Convergence adjustment .................................................25  
S
SAP sound..............................................................................52  
Satellite receiver connection...........................................10  
Scrolling the Theater Wide picture...............................32  
Set-top box ............................................................................12  
Size of Double-Window, adjusting ...............................35  
Sleep timer .............................................................................50  
Sound quality adjustments ..............................................53  
SPEAKERS on/off ...............................................................55  
Specifications........................................................................58  
SpeedSurf mode ..................................................................25  
SRS 3D surround.................................................................53  
StableSound® ........................................................................56  
Stereo sound .........................................................................52  
Sub-bass system (SBS) ....................................................54  
SurfLock™...............................................................................27  
S-video cables ........................................................................ 8  
D
Demo mode ...........................................................................57  
Display format.......................................................................47  
Double-window (“POP”) feature ...................................34  
DTV receiver connection ..................................................12  
DVD connection........................................................... 10, 11  
DVI/HDCP connection ......................................................14  
F G  
FAV yz buttons ..................................................................28  
FAVORITE button .................................................................37  
Favorite channels, programming...................................27  
Front of the TV........................................................................ 7  
Front panel lock ...................................................................43  
Game timer ............................................................................43  
T
Theater wide picture ......................................................... 31  
TouchFocus™.........................................................................25  
Troubleshooting .................................................................. 59  
TV/VIDEO button.......................................................... 27, 48  
V
L M  
V-CHI P  
Labeling channels ...............................................................29  
Labeling video inputs ........................................................48  
Language selection ............................................................22  
Last mode memory .............................................................57  
Locking channels ................................................................41  
Locking video inputs ..........................................................42  
Locks menu ...........................................................................38  
Menu system.........................................................................21  
MTS feature ...........................................................................52  
MUTE button.........................................................................52  
BLOCKING OPTION ......................................................40  
ENABLE BLOCKING .................................................... 39  
MPAA RATING ................................................................40  
NEW PIN CODE ..............................................................43  
TV RATING ........................................................................39  
Unlocking programs temporarily..............................41  
VCR connection ..................................................................... 8  
VIDEO LABEL ...................................................................... 48  
VIDEO LOCK .........................................................................42  
W
Warranty .......................................................................... 60, 61  
63  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TOSHIBA AMERICA CONSUMER PRODUCTS, L.L.C.  
HEAD OFFICE: 82 TOTOWA ROAD, WAYNE, NJ 07470, U.S.A.  
NATIONAL SERVICE DIVISION:1420-B TOSHIBA DRIVE, LEBANON, TN 37087, U.S.A.  
TOSHIBA OF CANADA LTD.  
HEAD OFFICE: 191 McNABB STREET, MARKHAM, ONTARIO, L3R 8H2, CANADA – TEL: (905) 470-5400  
SERVICE CENTERS:  
TORONTO: 191 McNABB STREET, MARKHAM, ONTARIO L3R 8H2, CANADA – TEL: (905) 470- 5400  
MONTREAL: 18050 TRANS CANADA, KIRKLAND, QUEBEC, H9J 4A1, CANADA – TEL: (514) 390-7766  
VANCOUVER: 22171 FRASERWOOD WAY, RICHMOND, B.C., V6W 1J5, CANADA – TEL: (604) 303-2500  
MANUFACTURED BY  
TOSHIBA AMERICA CONSUMER PRODUCTS, L.L.C.  
ColorStream and StableSound are registered trademarks of Toshiba America Consumer Products, L.L.C.  
CableClear, TouchFocus, and SurfLock are trademarks of Toshiba America Consumer Products, L.L.C.  
PRINTED IN USA  
(04-01) R  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Tripp Lite Network Cables N002 014 WH User Manual
Trust Computer Products Network Card IBM 80211a b g Wireless CardBus Adapter User Manual
Tunturi Home Gym C85 User Manual
United States Stove Furnace 22AF User Manual
Verilux Clock Radio VA06 User Manual
Victor Calculator 1205 2 User Manual
Victor CRT Television LYT1037 001A User Manual
Victory Refrigeration Freezer RUFS 1 S7 User Manual
ViewSonic Projector PJ359w User Manual
Water Boss Water System Series 255 User Manual