Toshiba Oxygen Equipment ST A10 User Manual

TOSHIBA POS Terminal  
ST-A10 SERIES  
Owner's Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Safety Summary  
SPTM-0009  
Safety Summary  
Personal safety in handling or maintaining the equipment is extremely important. Warnings and Cautions  
necessary for safe handling are included in this manual. All warnings and cautions contained in this manual  
should be read and understood before handling or maintaining the equipment.  
Do not attempt to effect repairs or modifications to this equipment. If a fault occurs that cannot be rectified  
using the procedures described in this manual, turn off the power, unplug the machine, then contact your  
authorized TOSHIBA TEC representative for assistance.  
Meanings of Each Symbol  
This symbol indicates warning items (including cautions).  
Specific warning contents are drawn inside the symbol.  
(The symbol on the left indicates a general caution.)  
This symbol indicates prohibited actions (prohibited items).  
Specific prohibited contents are drawn inside or near the symbol.  
(The symbol on the left indicates “no disassembling”.)  
This symbol indicates actions which must be performed.  
Specific instructions are drawn inside or near the symbol.  
(The symbol on the left indicates “disconnect the power cord plug from the outlet”.)  
This indicates that there is the risk of death or serious injury if the  
machines are improperly handled contrary to this indication.  
WARNING  
Do not plug in or unplug the  
power cord plug with wet  
hands as this may cause  
electric shock.  
Do not use voltages other than the  
voltage (AC) specified on the  
rating plate, as this may cause fire  
or electric shock.  
Any other than the  
specified AC voltage is  
prohibited.  
Prohibited  
Prohibited  
If the machines share the same  
outlet with any other electrical  
appliances that consume large  
amounts of power, the voltage  
will fluctuate widely each time  
these appliances operate. Be  
sure to provide an exclusive  
outlet for the machine as this  
may cause fire or electric  
shock.  
Do not place metal objects or  
water-filled containers such as  
flower vases, flower pots or mugs,  
etc. on top of the machines. If  
metal objects or spilled liquid enter  
the machines, this may cause fire  
or electric shock.  
Prohibited  
Do not insert or drop metal,  
flammable or other foreign  
objects into the machines  
through the ventilation slits, as  
this may cause fire or electric  
shock.  
Do not scratch, damage or modify  
the power cords. Also, do not  
place heavy objects on, pull on, or  
excessively bend the cords, as this  
may cause fire or electric shock.  
Prohibited  
Prohibited  
If the machines are dropped or  
their cabinets damaged, first  
turn off the power switches and  
disconnect the power cord  
plugs from the outlet, and then  
contact your authorized  
TOSHIBA TEC representative  
for assistance. Continued use  
of the machine in that condition  
may cause fire or electric  
shock.  
Continued use of the machines in  
an abnormal condition such as  
when the machines are producing  
smoke or strange smells may cause  
fire or electric shock. In these  
cases, immediately turn off the  
power switches and disconnect the  
power cord plugs from the outlet.  
Then, contact your authorized  
TOSHIBA TEC representative for  
assistance.  
Disconnect  
the plug.  
Disconnect  
the plug.  
(i)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Safety Summary  
SPTM-0009  
If foreign objects (metal  
When unplugging the power cords,  
be sure to hold and pull on the plug  
portion. Pulling on the cord portion  
may cut or expose the internal wires  
and cause fire or electric shock.  
Disconnect  
the plug.  
Disconnect  
fragments, water, liquids) enter  
the machines, first turn off the  
power switches and disconnect  
the power cord plugs from the  
outlet, and then contact your  
authorized TOSHIBA TEC  
representative for assistance.  
Continued use of the machine in  
that condition may cause fire or  
electric shock.  
the plug.  
Ensure that the equipment is  
properly grounded. Extension  
cables should also be grounded.  
Fire or electric shock could  
occur on improperly grounded  
equipment.  
Do not remove covers, repair or  
modify the machine by yourself.  
You may be injured by high  
voltage, very hot parts or sharp  
edges inside the machine.  
Unauthorized modification is  
prohibited.  
Connect a  
No  
disassembling.  
grounding wire.  
This indicates that there is the risk of personal Injury or damage to objects if  
the machines are improperly handled contrary to this indication.  
CAUTION  
Precautions  
The following precautions will help to ensure that this machine will continue to function correctly.  
Try to avoid locations that have the following adverse conditions:  
* Temperatures out of the specification  
* Shared power source  
* Direct sunlight  
* High humidity  
* Dust/Gas  
* Excessive vibration  
Do not subject the machine to sudden shocks.  
Do not press the keys too hard. Keys will operate correctly if they are touched lightly.  
Clean the cover and keyboard, etc. by wiping with a dry cloth or a cloth soaked with detergent and  
wrung out thoroughly. Never use thinner or other volatile solvent for cleaning.  
At the end of the day, turn the power OFF, then clean and inspect the exterior of the machine.  
Try to avoid using this equipment on the same power supply as high voltage equipment or equipment  
likely to cause mains interference.  
USE ONLY TOSHIBA TEC SPECIFIED consumables.  
DO NOT STORE the consumables where they might be exposed to direct sunlight, high temperatures, high  
humidity, dust, or gas.  
When moving the machine, take hold of the drawer and lift the machine.  
Do not place heavy objects on top of the machines, as these items may become unbalanced and fall  
causing injury.  
Do not block the ventilation slits of the machines, as this will cause heat to build up inside the  
machines and may cause fire.  
Do not lean against the machine. It may fall on you and could cause injury.  
Place the machine on a stable and level surface.  
Request Regarding Maintenance  
Utilize our maintenance services.  
After purchasing the machine, contact your authorized TOSHIBA TEC representative for assistance  
once a year to have the inside of the machine cleaned. Otherwise, dust will build up inside the  
machines and may cause a fire or a malfunction. Cleaning is particularly effective before humid rainy  
seasons.  
Our preventive maintenance service performs the periodic checks and other work required to maintain  
the quality and performance of the machines, preventing accidents beforehand.  
For details, please consult your authorized TOSHIBA TEC representative for assistance.  
Using insecticides and other chemicals  
Do not expose the machines to insecticides or other volatile solvents. This will cause the cabinet or  
other parts to deteriorate or cause the paint to peel.  
(ii)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SPTM-0009  
TABLE OF CONTENTS  
Page  
1.  
2.  
INTRODUCTION ----------------------------------------------------------- 1-1  
1.1 Accessories --------------------------------------------------------------------------------  
1-1  
APPEARANCE ------------------------------------------------------------- 2-1  
2.1 Standard Model ----------------------------------------------------------------------------  
2.2 Availabe Options ---------------------------------------------------------------------------  
2.3 Examples of POS Terminal with Some Options -----------------------------------  
2.4 Connectors ----------------------------------------------------------------------------------  
2-1  
2-3  
2-4  
2-5  
3.  
4.  
INSTALLATION PROCEDURE --------------------------------------  
3.1 Environment for Installation -------------------------------------------------------------  
3.2 Connecting the AC Plug -----------------------------------------------------------------  
3-1  
3-1  
3-2  
ADJUSTMENT -------------------------------------------------------------- 4-1  
4.1 Tilt Angle Adjustment --------------------------------------------------------------------  
4.2 Brightness Adjustment ------------------------------------------------------------------  
4-1  
4-2  
5
MAGNETIC CARD READER (OPTION)------------------------------ 5-1  
5.1 How to Read Magnetic card ------------------------------------------------------------  
5-1  
®
6.  
6-1  
6-1  
iButton (OPTION) -------------------------------------------------------  
6.1 How to Read iButton ----------------------------------------------------------------------  
7.  
8.  
9.  
GENERAL MAINTENANCE --------------------------------------------- 7-1  
TROUBLESHOOTING ---------------------------------------------------- 8-1  
SPECIFICATIONS -------------------------------------------------------- 9-1  
9.1 Basic Specifications ---------------------------------------------------------------------  
9.2 Option ----------------------------------------------------------------------------------------  
9-1  
9-2  
CAUTION!  
1. This manual may not be copied in while or in part without prior written  
permission of TOSHIBA TEC.  
2. The contents of this manual may be changed without notification.  
3. Please refer to your local Authorized Service representative with regard  
to any queries you may have in this manual.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SPTM-0009  
1. INTRODUCTION  
1.1 Accessories  
1. INTRODUCTION  
Thank you for choosing the TOSHIBA POS Terminal. This POS terminal contains all the high  
performance register functions necessary for a specialty/hospitality POS terminal and enables the  
user oriented system configuration.  
The operation panel can be chosen from 12-inch TFT display and 15-inch TFT display.  
This manual describes the functions and handling of this POS terminal and should be read  
carefully to help gain maximum performance and life from your POS terminal. For more queries  
please refer to this manual and keep it safe for future reference.  
1.1 Accessories  
Confirm that the following accessories are contained in the carton. If any accessories are missing  
or damaged, contact your TOSHIBA TEC service representative.  
Quick installation manual (1 copy)  
1-1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SPTM-0009  
2. APPEARANCE  
2. 1 Standard Model  
2. APPEARANCE  
2.1 Standard Model  
12-inch display POS terminal  
15-inch display POS terminal  
2-1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SPTM-0009  
2. APPEARANCE  
2. 1 Standard Model  
LED and CONTROL BUTTON  
DESCRIPTION  
This is the LED to indicate the power ON/OFF  
status of the POS terminal. The blue LED is  
illuminated when the power is ON.  
Power LED (Blue)  
The yellow LED is illuminated during the  
access to the hard disk drive.  
HDD LED (Yellow)  
Power Switch  
This is the switch to turn the power of the POS  
terminal ON or OFF.  
This is used to adjust the brightness of the  
operator’s display.  
Brightness Control  
2-2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SPTM-0009  
2. APPEARANCE  
2.2 Available Options  
2.2 Available Options  
Wireless Adaptor Case  
Fixed type customer display  
BIU  
Magnetic Card Reader  
(MCR)  
Tilt type customer display  
BIU  
iButton  
Remote type customer display  
RIU  
2-3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SPTM-0009  
2. APPEARANCE  
2.3 Examples of POS Terminal with Some Options  
2.3 Examples of POS Terminal with Some Options  
2-4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SPTM-0009  
2. APPEARANCE  
2.4 Connectors  
2.4 Connectors  
CAUTION!  
The drawer interface connector is exclusively for connecting the drawer. Do not connect a  
phone line or any other cables than the drawer cable to this connector. Doing so may cause a  
failure of the phone line and this terminal.  
2-5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SPTM-0009  
2. APPEARANCE  
2.4 Connectors  
Connector  
Description  
A connector for the AC inlet  
AC inlet  
PS/2 (Mouse, Keyboard) Mini-DIN 6-  
pin female type connector  
Connector for the PS/2 type mouse, Connector for the  
PS/2 type keyboard  
Connector for the USB (Universal Serial Bus) interface  
USB V2.0/1.1 and UHCI (Conforming to Universal Hub  
Controller Interface V2.0/1.1)  
USB: General 5V USB X 6  
NOTE: USB functions may not be supported  
depending on the Operating System.  
USB: 24V Powered  
X 1  
USB 6 ports can be used as general 5V USB  
connectors. Powered USB is a USB socket supplied  
with power, which is 1 port of 24V USB.  
Modular type connector for the 10BASE-T/100BASE-  
TX LAN interface, RJ-45 modular connector (with LED)  
LAN  
Connector for integrated Vacuum Fluorescent Display  
NOTE: When BIU is installed on the POS  
terminal, RIU is not available.  
BIU connector  
Connector for external Vacuum Fluorescent Display  
NOTE: When RIU is installed on  
RIU connector  
the POS terminal, BIU is not available.  
Cash drawer  
A 24V type TEC interface drawer is connectable  
Connectors for Speaker and Mic  
Speaker & Mic  
Expandable VGA interface. 15-pin VGA female type  
connector  
VGA  
COM 1, 2  
D-sub 9-pin male type connector (without power)  
D-sub 9-pin female type connector (with power)  
COM 3  
LVDS connector  
MCR connector  
A connector for Tablet  
A connector for magnetic card reader (MCR)  
2-6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SPTM-0009  
3. INSTALLATION PROCEDURE  
3.1 Environment for Installation  
3. INSTALLATION PROCEDURE  
WARNING!  
Care must be taken not to get your fingers caught between the LCD Frame and the POS terminal  
when bending the display downward.  
CAUTION!  
When removing the protective film from the display surface, please be sure to do it slowly. If it is  
done quickly, static electricity may generate, and the TFT may be damaged.  
3.1 Environment for Installation  
CAUTION!  
When installing the POS terminal, take the following precautions. Failure to do this may cause  
fire, electric shock, or injury.  
1. Avoid locations where it is subject to the following:  
• Direct sunlight  
• High temperature, high humidity  
• Rapid change in temperature  
• Excessive vibration  
• Dust  
2. Keep away from any devices that emit magnetism or electromagnetic wave.  
3. Keep away from flame or moisture.  
4. Be sure to place the POS terminal on a level and stable surface.  
1. Place the POS terminal on a level surface.  
2. Provide a minimum space to the left, right, front and rear of the POS terminal for proper cooling.  
(The unit has air vents and a fan on the front and left. Spaces should be provided to prevent the  
air vents from being blocked and the airflow from being obstructed.)  
See NOTE  
See NOTE  
NOTE: Do not block the ventilation of the fan. Fan is provided on these sides.  
3-1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SPTM-0009  
3. INSTALLATION PROCEDURE  
3.2 Connecting the AC Plug  
3.2 Connecting the AC Plug  
1. Push on both sides of the molded Tower (TWR) Tail Cover to remove it from the system in order to  
gain access of the AC inlet.  
2. Fully insert the Power Cord Plug into the Inlet of the POS terminal.  
Power  
Cord Plug  
TWR Tail  
Cover  
Inlet  
Push  
Power  
Cord Plug  
Push  
Lift  
NOTE: The Power cord is not included in the carton. Please prepare it separately from local dealer.  
3-2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SPTM-0009  
4. ADJUSTMENT  
4.1 Tilt Angle Adjustment  
4. ADJUSTMENT  
Tilt angle and brightness of the operator’s display can be adjusted.  
Adjustment method is common to both of 12-inch display model and 15-inch display model.  
CAUTION!  
1. Do not adjust the display angle by holding the LCD panel. Doing so may damage the unit. Be  
sure to hold the LCD frame.  
2. Care must be taken not to catch your fingers between POS terminal and the LCD Frame when  
bending the display backward.  
4.1 Tilt Angle Adjustment  
The tilt angle of the operator’s display can be adjusted freely from 10° to 60°.  
Hold both sides of the LCD frame, and slowly push the display upward/ downward to your best  
angle.  
The angle of the optional BIU (Tilt type customer display) is also adjustable as follows.  
4-1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SPTM-0009  
4. ADJUSTMENT  
4.2 Brightness Adjustment  
4.2 Brightness Adjustment  
The brightness control is provided on the lower right of the operator’s display.  
Turning it to the left makes the display darker, and turning it to the right makes the display brighter.  
4-2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SPTM-0009  
5. MAGNETIC CARD READER (OPTION)  
5.1 How to Read Magnetic Card  
5. MAGNETIC CARD READER (OPTION)  
The optional magnetic card reader can be installed.  
5.1 How to Read Magnetic Card  
Insert the magnetic card into the upper portion of the magnetic card reader slot and slowly  
move the card downward.  
NOTE: Moving the magnetic card too fast or too slowly may cause a read error.  
5-1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SPTM-0009  
6. iButton® (OPTION)  
6.1 How to Read iButton  
®
6. iButton (OPTION)  
The optional iButton unit can be installed on the bottom of the LCD.  
6.1 How to Read iButton  
CAUTION!  
1. Keep storage media, like a floppy disk, away from the touch probe. The magnet of the touch  
probe may destroy the stored data.  
2. Keep a metal object like a paper clip away from the touch probe. If such an object is attached  
to the touch probe, it may cause a short-circuit  
Data stored in an iButton can be read by attaching the iButton key to the touch probe. The magnet of  
the touch probe holds the iButton key.  
iButton Unit  
(Option)  
iButton Key  
NOTE: iButton key is local procurement  
6-1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SPTM-0009  
7. GENERAL MAINTENANCE  
7. GENERAL MAINTENANCE  
7. GENERAL MAINTENANCE  
WARNING!  
1. Be sure to disconnect the power cord prior to performing any maintenance.  
2. Do not pour water directly on or wipe the operator’s display with a soaked cloth, as this may  
cause fire, electric shock, or machine failure.  
CAUTION!  
1. Never use an organic solvent like thinners or benzene for cleaning. Using such solvents may  
discolor the covers.  
2. Do not use any sharp object to clean the operator’s display. Doing so may cause an operator’s  
display failure.  
3. Do not insert the nozzle of an air blower into the magnetic card reader slot. Doing so may  
damage the scanning head, resulting in the magnetic card reader failure.  
To help retain the high quality and performance of your POS Terminal, it should be cleaned  
regularly. The greater the usage on the POS Terminal, the more frequent the cleaning. (i.e. low  
usage = weekly: high usage = daily)  
• Cleaning the Operator’s Display  
Clean the surface of the operator’s display with a soft dry cloth or with an electrostatic free cleaner  
for automated office equipment.  
• Cleaning the Covers  
Wipe the covers with a soft dry cloth or soft cloth slightly moistened with mild detergent. After  
using detergent for cleaning, be sure to wipe it off with a slightly moistened cloth.  
7-1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SPTM-0009  
8. TROUBLESHOOTING  
8. TROUBLESHOOTING  
8. TROUBLESHOOTING  
WARNING!  
If you cannot solve a problem with the following solutions, do not attempt to repair it by  
yourself. Turn the power off, unplug the POS Terminal, then contact the nearest TOSHIBA  
TEC service representative for assistance  
Symptom  
The power does not turn  
on.  
Check Point  
• Is the power cord plugged in  
correctly?  
• Is the power supplied to the  
AC outlet?  
Solution  
• Plug in correctly.  
• If it is not a power failure,  
check for the power supply to  
the AC outlet with another  
electric appliance.  
When the power is not  
supplied, contact your nearest  
power company.  
• Has the circuit breaker  
blown?  
• Check the circuit breaker.  
The operator’s display is  
hard to see  
• Does the operator’s display  
reflects sunlight or room light? Adjustment and adjust the  
• Refer to Section 4  
• Is the tilt angle adjusted  
properly?  
• Is the brightness adjusted  
properly?  
display angle.  
• Refer to Section 4  
Adjustment and adjust the  
brightness properly.  
Magnetic card reader  
does comply-not read the  
data.  
• Does the used card comply  
with the standard?  
• Was the card moved too fast  
or too slowly?  
• Is the card reading direction  
correct?  
• Use ISO Track 1,2,3  
complying MCR.  
• Move the card at the proper  
speed. (10~150 cm/sec.)  
• Insert the card so that the  
magnetic strip faces the  
scanning head.  
NOTE: If any problem occurs other than the above, please contact your authorized TOSHIBA  
TEC representative.  
8-1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SPTM-0009  
9. SPECIFICATIONS  
9.1 Basic Specifications  
9. SPECIFICATIONS  
9.1 Basic Specifications  
Item  
Description  
VIA C7 1.5GHz  
CPU  
512 MB, 2 slots (2 GB max)  
3.5" HDD SATA (40 GB)  
Memory  
HDD  
ISO-3-track one sided type (option)  
MCR  
Option  
iButton Reader  
RS-232C  
4 (2x normal. 1x powered, 1x RIU connector)  
USB  
6
Powered USB  
PS/2  
Drawer  
VGA  
1
PS/2 Keyboard & PS/2 Mouse  
2
Interface  
1
10BASE-T/100BBASE-TX Ethernet  
RJ-45 modular connector (with LED)  
LAN  
Line-out/Mic-in  
Audio  
5°C - 40°C / 41F –104F  
10%-80% RH (Non condensation)  
Operating Temperature  
Operating Humidity  
12-inch LCD  
306mm (L) X 247mm (W) X 339mm (H) / 12” (L) X 9.7” (W) X 13.3” (H)  
366mm (L) X 251mm (W) X 360mm (H) / 14.4” (L) X 9.9” (W) X 14.2” (H)  
10.5 Kg / 23.1lb (Gross)  
Dimensions  
Weight  
15-inch LCD  
12-inch LCD  
15-inch LCD  
11.5 Kg / 25.4 lb (Gross)  
Power Supply  
Support OS  
95W Continuous Duty/150W Maximum Internal Switching Supply  
Win2000, XP, WEPOS, Linux Suse 9.3  
12-inch display  
12.1-inch color TFT with touch panel  
12.1-inch 800 x 600 dots  
15-inch display  
15-inch color TFT with touch panel  
15-inch 1024 x 768 dots  
Display type  
Display size  
Number of  
Colors  
Brightness  
Display area  
Dot size  
262K Color (262,144 Colors)  
230 cd/m2  
246 mm (W) x 184.5 mm (H)  
0.3075 mm (W) x 0.3075 mm (H)  
Analog Resistor Film  
(1024 x 1024 dots)  
262K Color (262,144 Colors)  
250 cd/m2  
304.1 mm (W) x 228.1 mm (H)  
0.297 mm (H) x 0.297 mm (H)  
Analog Resistor Film  
(1024 x 1024 dots)  
Operator’s  
Display  
Touch panel  
Brightness volume (TFT) and Tilt angle (Free adjustment in a range of 10° to  
Adjustment  
mechanism  
60°)  
No swivel adjustment  
Number of  
displayed  
5 x 7 dot fluorescent display 20 digits x 2 lines  
characters  
Display colour  
Blue  
Display area/  
character size  
Character size: 5.5 mm (W) x 10.5mm (H)  
Character pitch: 7.4 mm (W) x 15.5 mm (H)  
Customer  
Display  
Type font  
Display angle  
(tilt type)  
182 types of half width ANK  
Tilt: 0° to 45°  
Swivel: 0° to 145° (in both directions)  
(Option)  
Interface  
RS-232C interface (with power)  
9-1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SPTM-0009  
9. SPECIFICATIONS  
9.2 Options  
9.2 Options  
Option  
Model  
Description  
24V-drive standard drawer  
Dimensions and Weight:  
460(W) x 400(D) x 115(H) mm / 18.1(W) x 15.7 (D) x 4.5(H) inch  
10 Kg / 22 lb  
DRWST-51A-4MVK-QM-R  
DRWST-51A-8MVK-QM-R  
Money Case Type: MC4, 8  
Drawer Unit  
Bill  
Holder  
Coin  
Tray  
Type  
Mini Coin Case CDC  
Remarks  
Drawer  
4MVK-QM  
Type  
5
5
6
No  
1
Yes With media Slot  
Yes With media Slot  
8MVK-QM  
4
Tilt: 0° to 45°  
Swivel: 0° to 145° (in both direction)  
20 Characters x 2 lines dot display to be installed onto the POS  
terminal  
Tilt Type  
Customer  
Display  
LIUST-A10-BAK-QM-R  
Fixed Type  
Customer  
Display  
Fixed (no tilt and no swivel)  
20 Characters x 2 lines dot display to be installed onto the POS  
terminal  
LIUST-A10-FAK-QM-R  
Remote Type  
Customer  
Display  
Remote: Connected to terminal with an extended cable  
20 Characters x 2 lines dot display to be connected to the POS  
terminal  
LIUST-A10-RAK-QM-R  
TRST-A10 /A15 series  
Single thermal printer : TRST-A10  
Single thermal printer (Dual side printing): TRST-A15  
Printer Unit  
Magnetic  
Card Reader MCRST-A10-5K-QM-R  
(MCR)  
ISO Track 1,2,3 type magnetic card reader kit  
iButton unit to be installed onto the POS terminal (An iButton key is  
not included)  
iButton  
KIT-A10-BTNK-QM-R  
KIT-A10-WLCK-QM-R  
Wireless  
Adaptor Case  
Case and extension cable only  
9-2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
English  
Waste Recycling information for users:  
Following information is only for EU-member states:  
The crossed out wheeled bin symbol is used to indicate that the product must not be treated as general household waste.  
By ensuring that this product is disposed of correctly you will be helping to prevent potentially negative consequences for  
the environment and human health, which could otherwise be caused by incorrect waste handling of this product.  
For more detailed information about the take-back and recycling of this equipment, please contact the supplier that  
provided you with the product in question.  
French  
Information aux utilisateurs concernant le recyclage des déchets:  
Les informations suivantes sont uniquement destinées aux pays membres de l’Union Européenne:  
L’utilisation du symbole de "poubelle à roulettes barrée" indique que ce produit ne doit pas être traité comme un déchet  
ménager classique.  
En vous assurant que ce produit est correctement mis au rebut, vous participerez à la prévention de l’environnement et  
de la santé publique, contre des conséquences négatives potentielles qui pourraient résulter d’un traitement inapproprié  
des déchets de ce produit. Pour obtenir des informations complémentaires concernant la récupération et le recyclage de  
ce produit, veuillez contacter le fournisseur auprès duquel vous avez acheté le produit.  
German  
Wiederverwertungsinformationen für Verbraucher:  
Die folgenden Informationen gelten nur für EU-Mitgliedsstaaten:  
Das durchgestrichene Mülltonnensymbol weist darauf hin, dass dieses Produkt nicht wie allgemeiner Haushaltsmüll  
behandelt werden darf.  
Indem Sie aktiv mitwirken, dieses Produkt ordnungsgemäß zu entsorgen, helfen Sie mit, mögliche negative  
Auswirkungen auf die Umwelt sowie die menschliche Gesundheit zu vermeiden, die sonst durch die unsachgemäße  
Entsorgung dieses Produktes beeinträchtigt werden könnten.  
Für nährere Informationen zur Rücknahme und Wiederverwertung dieses Produktes wenden sie sich bitte an den  
Lieferanten, von dem Sie dieses Produkt erworben haben.  
Spanish  
Información para usuarios sobre el reciclaje de residuos:  
La siguiente información sólo concierne a los Estados Miembros de la UE:  
El uso del símbolo de un contenedor con ruedas tachado indica que este producto no puede ser tratado como si fuera  
un residuo doméstico.  
Asegurando que nos deshacemos de este producto de forma correcta, ayudaremos a evitar potenciales consecuencias  
negativas tanto para el medio ambiente como para la salud pública, que podrían producirse debido a un tratamiento  
inapropiado de este producto. Para obtener una información más detallada sobre la recogida y reciclaje de su producto,  
por favor, póngase en contacto con el proveedor donde lo compró.  
Dutch  
Gebruikersinformatie over het recycleren van afval:  
De volgende informatie geldt enkel in EU-lidstaten:  
Het symbool met de doorkruiste afvalbak geeft aan dat dit product niet mag worden behandeld als algemeen  
huishoudelijk af val.  
Door dit product op de juiste manier van de hand te doen beschermt u het milieu en de volksgezondheid tegen mogelijke  
negatieve gevolgen, die anders zouden kunnen voortvloeien uit het onjuist verwerken van de resten van dit product.  
Voor gedetailleerde informatie over het terugnemen en recycleren van dit product, gelieve contact op te nemen met de  
leverancier van dit product.  
Italian  
Informazioni sul riciclo del prodotto:  
Le seguenti informazioni riguardano gli stati membri EU:  
Il simbolo con il bidone sbarrato indica il non poter smaltire questo prodotto come rifiuto domestico.  
L'accertamento che questo prodotto sia smaltito correttamente contribuirà ad impedire le potenziali conseguenze  
negative per l'ambiente e la salute umana che potrebbero essere causati, al contrario, dall'errato smaltimento dello  
stesso. Per informazioni più dettagliate sulle modalita di resa e riciclaggio di questo prodotto mettetevi in contatto con il  
fornitore da cui l'avete aquistato.  
Portuguese  
Informação sobre reciclagem:  
A informação que se segue é apenas dirigida a países membros da CEE:  
A utilização deste símbolo indica que este produto não pode ser tratado como lixo comum.  
Ao assegurar-se que este produto é tratado correctamente está a ajudar a prevenir potenciais consequências negativas  
para o ambiente e para a saúde humana, que poderiam ser causadas pelo inapropriado tratamento deste produto.  
Para mais informação sobre a reciclagem e tratamento deste produto, contacte o seu fornecedor.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PRINTED IN SINGAPOLE  
SPTM-0009  
E
Download from Www.Somanuals.com. All Manuals Search And Download.  

Tatung Indoor Furnishings TRK 191 User Manual
Teac Computer Drive DV W28SS V User Manual
Team Products Drill PMD8127 User Manual
Tektronix Welding System AWG5000 Series User Manual
Texas Instruments Calculator MSP50C6xx User Manual
Thermador Double Oven SEC271 User Manual
Toastmaster Griddle TG21WL TG21WCAN User Manual
Topcom Network Router WBR 7011 B User Manual
Tunturi Bicycle TRAINER E 604 User Manual
Tyco Electronics Computer Monitor B1ET 1215L User Manual