TEAM PRODUCTS INTERNATIONAL INC. Limited Warranty
WhAT IS COvERED: Any defect in materials and workmanship.
FOR hOW LONg: 2 years from date of purchase.
WhAT WE WILL DO: If your product is defective and returned within 30 days
after the date it was purchased, we will replace it at no charge to you. If
returned after 30 days but within 2 years of the date of purchase we will
repair it or, at our option, replace it at no charge to you.
If we repair your product, we may use new or reconditioned replacement
parts. If we choose to replace your product, we may replace it with a
new or reconditioned one of the same or similar design. The repair or
replacement will be warranted under our standard 2 year warranty.
LIMITATIONS: IMPLIED WARRANTIES, INCLUDINg ThOSE OF FITNESS FOR A
PARTICULAR PURPOSE AND MERChANTAbILITy (AN UNWRITTEN WARRANTy
ThAT ThE PRODUCT IS FIT FOR ORDINARy USE), ARE LIMITED TO 2 yEARS
FROM DATE OF PURChASE. WE WILL NOT PAy FOR LOSS OF TIME, INCONvE-
NIENCE, LOSS OF USE OF yOUR PRODUCT OR PROPERTy DAMAgE CAUSED
by yOUR PRODUCT OR ITS FAILURE TO WORk, OR ANy OThER INCIDENTAL
OR CONSEqUENTIAL DAMAgES INCLUDINg PERSONAL INjURy.
Some states do not allow limitations on how long an implied warranty
lasts or the exclusion or limitation of incidental or consequential damages,
so the above exclusions or limitations may not apply to you.
12V, 14.4V, 18V
Cordless Drills
WhAT WE ASk yOU TO DO: To get warranty service for your product,
you must provide proof of the date of purchase. Within 30 days of the
date it was purchased, return your product to your place of purchase for
immediate replacement. After 30 days, but before the end of the 2 year
warranty period, you may return the product to the following address:
Team Products International
Attn: Customer Service Returns
Owner’s Manual
35 A Continental Drive
Wayne, Nj 07470
We suggest that you retain your original packing material in the event
you need to ship your product. When sending your product include your
name, address, phone number, proof of date of purchase, and a
description of the operating problem. After repairing or replacing your
product, we will ship it to your home or office within four weeks.
WhAT ThIS WARRANTy DOES NOT COvER: Among oTher ThIngS ThIS
WArrAnTy doeS noT cover defecTS reSulTIng from AccIdenTS,
dAmAge WhIle In TrAnSIT To our ServIce locATIon, AlTerATIonS,
unAuThorIzed repAIr, fAIlure To folloW InSTrucTIonS, mISuSe, fIre,
flood, And AcTS of god. If your producT IS noT covered by our
WArrAnTy, cAll our cuSTomer ServIce number AT (888) 231-4022 To
deTermIne WheTher We WIll repAIr your producT And oTher repAIr
InformATIon, IncludIng chArgeS. We, AT our opTIon, mAy replAce
rATher ThAn repAIr your producT WITh A neW or recondITIoned
one of The SAme or SImIlAr deSIgn. The repAIr or replAcemenT WIll
be WArrAnTed for 2 yeArS.
Models: PMD8127
PMD8128
PMD8129
PMD8131
PMD8133
ThIS lImITed WArrAnTy IS The only one We gIve on your producT,
And IT SeTS forTh All our reSponSIbIlITIeS regArdIng your producT.
There Are no WArrAnTIeS WhIch exTend beyond The deScrIpTIon SeT
forTh Above.
©2006The Coleman Company, Inc. All rights reserved.
STATE LAW RIghTS: This warranty gives you specific legal rights and you
may also have other rights which may vary from state to state.
COLEMAN® and
are registered trademarks ofThe Coleman Company, Inc., used under license.
Designed in the USA and custom-manufactured in China forTeam Products International Inc.
Distributed byTeam Products International Inc., Mountain Lakes, NJ 07046.
PMD121505-205
Download from Www.Somanuals.com. All Manuals Search And Download.
12V, 14.4V, 18V
Cordless Drills
Owner’s Manual
5.To reduce the risk of damaging the battery charger power cord, be sure to pull
the plug rather then the cord when disconnecting it from the power supply.
Always position the cord so it will not be stepped on or tripped over.This will
prevent damage to the cord.
Controls and Components:
Batteries and AC Charger
1. Battery with Release Buttons On Each Side (PMD8133 includes 2 batteries)
2. 120V AC Adaptor
3. Charging Stand with LED Charging Indicators
6. An extension cord should not be used unless absolutely necessary. Use of an
improper extension cord can result in risk of fire or electric shock. If using an
extension cord make sure that:
A)The pins on the plug of the extension cord are the same number,
size and shape as those on the plug on the charger.
1
7
6
5
B)The extension cord is properly wired and in good working
condition.
4
C)The wire size is the same or larger than the ones specified below:
10
Recommended size of Extension Cord for Battery Charger
8
Length of Cord (Feet)
AWG Size of Cord*
25
18
50
18
100
16
150
14
9
2
*The smaller the AWG (American Wire Gauge) number of the extension cord,
the higher the capacity of the cable for conducting current to ensure proper
usage of the tool.
11
3
7. Do not operate charger with a damaged cord or plug.
8. Do not operate the charger if it has received a sharp blow, been dropped or
damaged in any other way.
12
13
9. Do not open the drill, battery or battery charger.There are no user serviceable
parts. Opening the unit will void the warranty.
14
10. Unplug the charger from its power source when not in use.
Drill:
11. Do not touch the terminals inside the battery charger with any other metal
object such as nails or coins.This can short the charger.
4. 3/8” Jacobs Keyless Chuck
5. 24 AdjustableTorque Settings Control Ring
6. Forward/Lock/Reverse Switch
12. Do not store the unit in areas where the temperature can exceed 120°F.
7. High/Low Speed Switch (PMD8131 and PMD8133 only)
8. Variable SpeedTrigger Switch
13. Do not throw the battery or battery charger in fire.This can cause an
explosion.
9. Accessory/Bit Holder
14. During extreme conditions, the battery may leak. This does not indicate a
battery failure. However, if the liquid gets on your skin, immediately wash
with soap and water, neutralize the area with a mild acid such as lemon juice
or vinegar. If the liquid gets into your eyes, flush them with clean water
immediately for a minimum of 10 minutes and seek medical attention.
10. Comfort Rubber Grip (PMD8131 and PMD8133 only)
Accessories:
11. 6 Various Screwdriver Bits
12. 2” Extension Bar
13. 2 Double Ended Screwdriver Bits
14. 6 Various Drill Bits
(Each Drill comes with a storage case.)
3
4
Download from Www.Somanuals.com. All Manuals Search And Download.
12V, 14.4V, 18V
Cordless Drills
Owner’s Manual
INSTRUCTIONS FOR USE:
ChargingThe Battery
NOTE: While the battery is placed in the charger, the RED LED indicator light
will remain on. If charging more than one battery, wait at least 15 minutes
between each charge. Use only the battery charger that is supplied with this
tool. Using another charger may cause damage to the battery.
THE BATTERY(IES) MAY NOT BE FULLY CHARGED FROMTHE
FACTORY. READ ALL INSTRUCTIONSTHOROUGHLY PRIORTO FIRST
USE.
WARNING: Never charge a battery pack again immediately after it has been
fully charged.This can give rise to the battery pack being overcharged and a
reduced battery life. DO NOT leave the battery pack in the charger for more than
8 hours.
The Drills covered by this manual use the same battery and battery charger.
Your Drill comes complete with a rechargeable battery which we recommend
that you fully charge before the first use.
Drill must be charged for 8 hours prior to first use. After initial charge, allow
approximately 3 to 8 hours to recharge your battery.
UsingThe Drill
CAUTION: Always make sure that the tool is switched
OFF and the battery pack is removed from the drill
before changing any bits.
The battery should be recharged when the drill does not operate up to its
normal performance level. Do not continue to operate the drill in this depleted
capacity. Recharge the battery immediately.
Loosen the keyless chuck by holding the ring and
turning the sleeve counter clockwise. Select the drill
bit or screwdriver you want to use and place it in
the keyless chuck.Twist the sleeve of the keyless
chuck clockwise to tighten it, making sure the drill bit
remains in the center of the keyless chuck’s teeth.
To increase the life of your battery, do not leave the battery charging for more
than 8 hours. While this is not a safety concern, overcharging may reduce the
life of the battery.
Overtime, if drill is not used, the battery will lose capacity. For maximum
performance, recharge the battery after prolonged storage or non-use periods.
Twist the 24 setting torque control ring to the desired
setting. Lower settings are better for light work such
as driving screws into soft materials. Higher settings are
recommended for drilling into harder surfaces.
NOTE: Before inserting or removing the battery from the charging base, always
ensure that the base is not plugged into a 120V power source.
When properly adjusted, the clutch will slip at its present
torque setting to prevent driving the screw too deep or
to prevent damage to the tool.
1.To begin charging, remove the battery pack from the tool by pressing on the
battery release buttons on either side of the battery pack and pulling down.
To operate the drill in forward setting, simply keep the
Forward/Lock/Reverse switch flat against the
side of the drill as shown.To change to reverse
setting, move the Forward/Lock/Reverse switch
until it is flat against the opposite side of the
drill. Keeping the Forward/Lock/Reverse switch
in the center position locks the drill and prevents
unintentional use. It is recommended that the
Drill is in the locked position when it is not in use
or is being stored.
2. Plug the battery pack into the battery charger making sure the positive (+) and
negative (-) poles of the battery match the positive (+) and negative (-) poles
of the battery charger.
NOTE: The battery will only fit into the battery charger and the tool one way.
3. Plug one end of the 120 Volt AC Adaptor into the battery charger and the
other end into any standard 120 Volt wall outlet.The RED LED indicator on the
battery charger will illuminate to indicate that the battery is charging.
CAUTION: Always check the direction of the rotation before using the drill.
4. Full charging will take between 3 to 8 hours.
The speed of the drill is increased by the amount of pressure you place on the
ON/OFF trigger switch.The less pressure you put on the trigger switch, the
slower the drill will go.
5
6
Download from Www.Somanuals.com. All Manuals Search And Download.
12V, 14.4V, 18V
Cordless Drills
Owner’s Manual
TROUBLESHOOTINGTIPS:
DRILL DOES NOT WORK?
• Recharge the battery
Your drill comes with an automatic braking function that quickly stops the chuck
from turning when the trigger switch is released.
Your drill (models PMD8131 and PMD8133) has two speed ranges; low speed
(position 1) (0-400 rpm) and high speed (position 2 ) (0-1100 rpm).
CHARGING INDICATOR LED NOT ILLUMINATED DURING
RECHARGING?
Screwdriver Operation
• Check that battery pack is properly connected to the battery charger
• Check that the AC Adaptor is properly connected at both ends
Place the point of the screwdriver bit into the head of the screw and apply slight
pressure to the tool. Press the trigger switch slightly and then gradually increase
the drill speed. Release the trigger switch as soon as the clutch engages.
Note: Starting the drill at too high of a speed can
damage the drill bit or reduce the life of the bit.
SPECIFICATIONS for PMD8127
Voltage
12V
Make sure that the driver bit is inserted straight in
the screw head or the screw may become damaged
or will not be inserted properly. When driving wood
screws, pre-drill pilot holes into the surface to make
driving easier.This will also prevent the wood from
splitting.
Speed 1
0-600RPM
24 + Drill
Torque Settings
Chuck Capacity
Charger Input
ChargingTime
BatteryType
up to 3/8”
120V AC 60Hz
Approx. 3 –8 Hours
Ni-Cad
Note: When drilling, the drill bit can become stuck.
If this happens, a very high torque will be produced.
Always take care to hold the drill firmly to prevent
possible damage or injury.
SPECIFICATIONS for PMD8128
Maintenance
Voltage
14.4V
Clean the Drill regularly. Before cleaning, remove the battery pack and any
accessories (bits etc.).To clean, use ONLY a mild soap and damp cloth on the
housing. Never immerse drill in any kind of fluid. Do not use any solvents or
harsh abrasives on the drill housing as this may cause damage to the unit.
Always keep the ventilation openings clear.
Speed 1
0-600RPM
24 + Drill
Torque Settings
Chuck Capacity
Charger Input
ChargingTime
BatteryType
up to 3/8”
120V AC 60Hz
Approx. 3 –8 Hours
Ni-Cad
NOTE: All bearings in these tools are lubricated with a sufficient amount of
high-grade lubricant for the life of the unit under normal operating conditions.
No further lubrications required.
CAUTION: DO NOT keep the trigger switch pressed in with tape or any other
permanent means or the circuit will not function properly. A malfunction may
result, possibly causing overheating or damage to the unit.
Do not open the drill, battery or battery charger.There are no user serviceable
parts. Opening the unit will void the warranty.
7
8
Download from Www.Somanuals.com. All Manuals Search And Download.
12V, 14.4V, 18V
Cordless Drills
Owner’s Manual
SPECIFICATIONS for PMD8129
Voltage
18V
Speed 1
0-600RPM
24 + Drill
Torque Settings
Chuck Capacity
Charger Input
ChargingTime
BatteryType
up to 3/8”
120V AC 60Hz
Approx. 3 –8 Hours
Ni-Cad
SPECIFICATIONS for PMD8131 and PMD8133
Voltage
18V
Speed 1
0-400RPM
0-1100RPM
24 + Drill
Speed 2
Torque Settings
Chuck Capacity
Charger Input
ChargingTime
BatteryType
up to 3/8”
120V AC 60Hz
Approx. 3 –8 Hours
Ni-Cad
Questions?
If you have any questions about this product, please contact our Customer
Service Department at (888) 231-4022, 9 AM to 5 PM EST, Monday through
9
10
Download from Www.Somanuals.com. All Manuals Search And Download.
|