Toshiba Laptop toshiba satellite User Manual

TOSHIBA  
Satellite L550/  
Satellite Pro L550/  
Satellite L550D/  
Satellite Pro L550D series  
User's Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ConfigFree is a trademark of TOSHIBA Corporation.  
DVD MovieFactory is trademark of the Corel Corporations.  
Manufactured under license from Dolby Laboratories.  
PC Card is a trademark of PCMCIA  
HDMI, the HDMI logo and High-Definition Multimedia Interface are  
trademarks or registered trademarks of HDMI Licensing LLC.  
LabelFlashTM is trademark of YAMAHA Corporation.  
Photo CD is a trademark of Eastman Kodak.  
Wi-Fi is a registered trademark of the Wi-Fi Alliance.  
Memory Stick and Memory Stick PRO are registered trademarks of SONY  
Corporation.  
Secure Digital and SD are trademarks of SD Card Association.  
MultiMediaCard and MMC are trademarks of MultiMediaCard Association.  
Other trademarks and registered trademarks not listed above may be used  
in this manual.  
Macrovision License of Notice  
For DVD Manufacturing License Agreement  
This product incorporates copy protection technology that is protected by  
U.S. and foreign patents, including patent numbers 5,315,448; 5,583,936;  
6,836,549 and 7,050,698, and other intellectual property rights. The use of  
Macrovision’s copy protection technology in the product must be authorized  
by Macrovision. Reverse engineering or disassembly is prohibited.  
FCC information  
FCC notice "Declaration of Conformity Information"  
This equipment has been tested and found to comply with the limits for a  
Class B digital device, pursuant to part 15 of the FCC rules. These limits  
are designed to provide reasonable protection against harmful interference  
in a residential installation. This equipment generates, uses and can radiate  
radio frequency energy and, if not installed and used in accordance with the  
instructions, may cause harmful interference to radio communications.  
However, there is no guarantee that interference will not occur in a  
particular installation. If this equipment does cause harmful interference to  
radio or television reception, which can be determined by turning the  
equipment off and on, the user is encouraged to try to correct the  
interference by one or more of the following measures:  
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and receiver.  
Connect the equipment into an outlet on a circuit different from that to  
which the receiver is connected.  
Consult the dealer or an experienced radio/TV technician for help.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
iii  
   
Only peripherals complying with the FCC class B limits may be attached to  
this equipment. Operation with non-compliant peripherals or peripherals  
not recommended by TOSHIBA is likely to result in interference to radio  
and TV reception. Shielded cables must be used between the external  
devices and the computer’s external monitor port, Universal Serial Bus  
(USB 2.0) ports, HDMI out port and microphone jack. Changes or  
modifications made to this equipment, not expressly approved by  
TOSHIBA or parties authorized by TOSHIBA could void the user’s  
authority to operate the equipment.  
FCC conditions  
This device complies with part 15 of the FCC Rules. Operation is subject to  
the following two conditions:  
1. This device may not cause harmful interference.  
2. This device must accept any interference received, including  
interference that may cause undesired operation.  
Contact  
Address:  
TOSHIBA America Information Systems, Inc.  
9740 Irvine Boulevard  
Irvine, California 92618-1697  
Telephone: (949) 583-3000  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
iv  
EU Conformity Statement  
This product and - if applicable - the supplied accessories too are marked  
with "CE" and comply therefore with the applicable harmonized European  
standards listed under the Low Voltage Directive 2006/95/EC, the EMC  
Directive 2004/108/EC and/or R&TTE Directive 1999/5/EC.  
Responsible for CE-marking:  
TOSHIBA EUROPE GMBH, Hammfelddamm 8, 41460 Neuss, Germany.  
Manufacturer:  
Toshiba Corporation, 1-1 Shibaura 1-chome, Minato-ku, Tokyo, 105-8001,  
Japan  
The complete official EU CE Declaration can be obtained on following  
internet page: http://epps.toshiba-teg.com/  
VCCI Class B Information  
Canadian regulatory information (Canada only)  
This digital apparatus does not exceed the Class B limits for radio noise  
emissions from digital apparatus as set out in the Radio Interference  
Regulation of the Canadian Department of Communications.  
Note that Canadian Department of Communications (DOC) regulations  
provide, that changes or modifications not expressly approved by  
TOSHIBA Corporation could void your authority to operate this equipment.  
This Class B digital apparatus meets all requirements of the Canadian  
Interference-Causng Equipment Regulations.  
Cet appareil numérique de la class B respecte toutes les exgences du  
Règlement sur le matériel brouileur du Canada.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
v
     
Modem warning notice  
Conformity Statement  
The equipment has been approved to [Commission Decision “CTR21”] for  
pan-European single terminal connection to the Public Switched Telephone  
Network (PSTN).  
However, due to differences between the individual PSTNs provided in  
different countries/regions the approval does not, of itself, give an  
unconditional assurance of successful operation on every PSTN network  
termination point.  
In the event of problems, you should contact your equipment supplier in the  
first instance.  
Network Compatibility Statement  
This product is designed to work with, and is compatible with the following  
networks. It has been tested to and found to conform with the additional  
requirements conditional in EG 201 121.  
Germany  
ATAAB AN005, AN006, AN007, AN009, AN010  
and DE03, 04, 05, 08, 09, 12, 14, 17  
Greece  
ATAAB AN005, AN006 and GR01, 02, 03, 04  
Portugal  
ATAAB AN001, 005, 006, 007, 011 and  
P03, 04, 08, 10  
Spain  
Switzerland  
ATAAB AN005, 007, 012, and ES01  
ATAAB AN002  
All other countries/regions ATAAB AN003, 004  
Specific switch settings or software setup is required for each network,  
please refer to the relevant sections of the user guide for more details.  
The hookflash (timed break register recall) function is subject to separate  
national type approvals. It has not been tested for conformity to national  
type regulations, and no guarantee of successful operation of that specific  
function on specific national networks can be given.  
Japan regulations  
Region selection  
If you are using the computer in Japan, technical regulations described  
under Telecommunications Business Law require that you select the Japan  
region mode. It is illegal to use the modem in Japan with any other  
selection.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
vi  
   
Redial  
Up to two redial attempts can be made. If more than two redial attempts are  
made, the modem will return Black Listed. If you are experiencing  
problems with the Black Listed code, set the interval between redials at one  
minute or longer.  
Japan’s Telecommunications Business Law permits up to two redials on  
analogue telephones, but the redials must be made within a total of three  
minutes.  
The internal modem is approved by the Japan Approvals Institute for  
Telecommunications Equipment.  
A05-0413001  
A05-0025001  
SUBTEL 3061  
IC: 109AH-ML3054  
TEC/WR/I/MOD-08/02/100.JAN 05  
MOROCCO : 2903/2005  
0617-05-1699  
Approved by PTA (2004)  
FCC NO.:US:S56MD01B13054  
Model Number:ML3054  
TE-A22/K012-04-0422  
E04/01/211/G  
EQUIPO  
Pakistan Telecom Authority  
E253445  
HOMOLOGADO POR  
ANTEL  
NYCE/CT/0008/06/TS  
Cofetel n° : TTD:MOML06-189  
No de Aprob: MC-108  
Fecha: 20/12/2005  
Empresa: Motorola Inc  
NTC  
This Motorola ML3054 56k  
Modem may be connected  
to the Telecom Network  
POSTEL  
02375/POSTEL/2007  
Type Approved  
No.:ESD-CPE-0400760  
PTC / 211 / 05 / 005  
Made In China  
Name of permit owner: Ronny Cabouly  
Telephone: 03-9506328  
Model: ML3054  
Manufacturer: MOTOROLA INC.  
Country of manufacture: USA  
Type approval No.: 7-12840-0-101926  
Valid from: 2004  
Permit No.: 13-12840-0-101927  
Valid from:2004  
Complies with  
IDA Standards  
DA 103255  
A05-0025001  
TE-2004/175  
B93M1015-F  
MOTOROLA ML3054  
54-3708  
MOTOROLA  
N723Z218  
No.#SL405007  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
vii  
Delphi D40  
This Agere Delphi D40 56K  
Modem may be connected  
to the Telecom Network  
US:AGSMD01BDELPHI  
PTC 211/05/074  
A05-0413001  
NYCE/CT/0003/07/TS  
Cofetel no : TTDAGDE07-056  
Agere Systems  
Delphi Modem D40  
Approval No. 3785  
N723  
No:ESD-CPE-0500938  
Factory ID: E  
Agere DELPHI D40(AM5)  
54-5681  
Agere Systems Inc.  
CCAC07M10010T6  
0107898349890382  
115/06  
Approval by PTA,2007  
0455-06-2565  
AM5  
ETISALAT PERMIT NO.:E05/01/254/G  
Certificate No.#SL405083  
NCG-CE-06-009  
TEC/WR/I/MOD-08/02/122.MAY07  
IC:4005B-DELPHI, REN:0.1  
ASI-DELPHI-D40  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Type of service  
Your modem is designed to be used on standard-device telephone lines.  
Connection to telephone company-provided coin service (central office  
implemented systems) is prohibited. Connection to party lines service is  
subject to state tariffs. If you have any questions about your telephone line,  
such as how many pieces of equipment you can connect to it, the  
telephone company will provide this information upon request.  
Telephone company procedures  
The goal of the telephone company is to provide you with the best service it  
can. In order to do this, it may occasionally be necessary for them to make  
changes in their equipment, operations, or procedures. If these changes  
might affect your service or the operation of your equipment, the telephone  
company will give you notice in writing to allow you to make any changes  
necessary to maintain uninterrupted service.  
If problems arise  
If any of your telephone equipment is not operating properly, you should  
immediately remove it from your telephone line, as it may cause harm to  
the telephone network. If the telephone company notes a problem, they  
may temporarily discontinue service. When practical, they will notify you in  
advance of this disconnection. If advance notice is not feasible, you will be  
notified as soon as possible. When you are notified, you will be given the  
opportunity to correct the problem and informed of your right to file a  
complaint with the FCC. In the event repairs are ever needed on your  
modem, they should be performed by TOSHIBA Corporation or an  
authorized representative of TOSHIBA Corporation.  
Disconnection  
If you should ever decide to permanently disconnect your modem from its  
present line, please call the telephone company and let them know of this  
change.  
Fax branding  
The Telephone Consumer Protection Act of 1991 makes it unlawful for any  
person to use a computer or other electronic device to send any message  
via a telephone fax machine unless such a message clearly contains in a  
margin at the top or bottom of each transmitted page, or on the first page of  
the transmission, the date and time it is sent, an identification of the  
business, other entity or individual sending the message and the telephone  
number of the sending machine or such business, other entity or individual.  
In order to program this information into your fax modem, you should  
complete the setup of your fax software before sending messages.  
Use only No. 26 AWG or larger telecommunication line cord.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ix  
Instructions for IC CS-03 certified equipment  
1. The Industry Canada label identifies certified equipment. This  
certification means that the equipment meets certain  
telecommunications network protective, operational and safety  
requirements as prescribed in the appropriate Terminal Equipment  
Technical Requirements document(s). The Department does not  
guarantee the equipment will operate to the user’s satisfaction.  
Before installing this equipment, users should ensure that it is  
permissible to be connected to the facilities of the local  
telecommunications company. The equipment must also be installed  
using an acceptable method of connection.  
The customer should be aware that compliance with the above  
conditions may not prevent degradation of service in some situations.  
Repairs to certified equipment should be coordinated by a  
representative designated by the supplier. Any repairs or alterations  
made by the user to this equipment, or equipment malfunctions, may  
give the telecommunications company cause to request the user to  
disconnect the equipment.  
Users should ensure for their own protection that the electrical ground  
connections of the power utility, telephone lines and internal metallic  
water pipe system, if present, are connected together. This precaution  
may be particularly important in rural areas.  
Users should not attempt to make such connections themselves, but  
should contact the appropriate electric inspection authority, or electrician,  
as appropriate.  
2. The user manual of analog equipment must contain the equipment’s  
Ringer Equivalence Number (REN) and an explanation notice similar to  
the following:  
The Ringer Equivalence Number (REN) of the modem can vary - for the  
REN, please refer to the modem's label.  
The Ringer Equivalence Number (REN) assigned to each terminal device  
provides an indication of the maximum number of terminals allowed to be  
connected to a telephone interface. The termination on an interface may  
consist of any combination of devices subject only to the requirement that  
the sum of the Ringer Equivalence Numbers of all the devices does not  
exceed 5.  
3. The standard connecting arrangement (telephone jack type) for this  
equipment is jack type(s): USOC RJ11C.  
The IC registration number of the modem is shown below.  
Canada: 4005B-DELPHI  
109AH-ML3054  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
x
 
Notes for Users in Australia and New Zealand  
Modem warning notice for Australia  
Modems connected to the Australian telecoms network must have a valid  
Austel permit. This modem has been designed to specifically configure to  
ensure compliance with Austel standards when the country/region selection  
is set to Australia. The use of other country/region settings while the  
modem is attached to the Australian PSTN would result in your modem  
being operated in a non-compliant manner. To verify that the country/region  
is correctly set, enter the command ATI which displays the currently active  
setting.  
To set the country/region permanently to Australia, enter the following  
command sequence:  
AT%TE=1  
ATS133=1  
AT&F  
AT&W  
AT%TE=0  
ATZ  
Failure to set the modem to the Australia country/region setting as shown  
above will result in the modem being operated in a non-compliant manner.  
Consequently, there would be no permit in force for this equipment, with the  
Telecoms Act 1991 prescribing a penalty of $12,000 for the connection of  
non-permitted equipment.  
Notes for use of this device in New Zealand  
The grant of a Telepermit for a device in no way indicates Telecom  
acceptance of responsibility for the correct operation of that device  
under all operating conditions. In particular the higher speeds at which  
this modem is capable of operating depend on a specific network  
implementation which is only one of many ways of delivering high  
quality voice telephony to customers. Failure to operate should not be  
reported as a fault to Telecom.  
In addition to satisfactory line conditions a modem can only work  
properly if:  
a/ It is compatible with the modem at the other end of the call, and;  
b/ The application using the modem is compatible with the application  
at the other end of the call - for example, accessing the Internet  
requires suitable software in addition to a modem.  
This equipment shall not be used in any manner which could constitute  
a nuisance to other Telecom customers.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
xi  
 
Some parameters required for compliance with Telecom’s PTC  
Specifications are dependent on the equipment (PC) associated with  
this modem. The associated equipment shall be set to operate within  
the following limits for compliance with Telecom Specifications:  
a/ There shall be no more than 10 call attempts to the same number  
within any 30 minute period for any single manual call initiation, and;  
b/ The equipment shall go on-hook for a period of not less than 30  
seconds between the end of one attempt and the beginning of the  
next, and;  
c/ Automatic calls to different numbers shall be not less than 5  
seconds apart.  
Immediately disconnect this equipment should it become physically  
damaged, and arrange for its disposal or repair.  
The correct settings for use with this modem in New Zealand are as  
follows:  
ATB0 (CCITT operation)  
AT&G2 (1800Hz guard tone)  
AT&P1 (decadic dialing make-break ratio =33%/67%)  
ATS0=0 (disable auto answer)  
ATS6=4 (blind dial delay)  
ATS7=Less than 90 (time to wait for carrier after dialing)  
ATS10=Less than 150 (loss of carrier to hangup delay - the factory  
default of 15 is recommended)  
ATS11=90 (DTMF dialing on/off duration in milliseconds)  
ATX2 (dial tone detect, but not USA call progress detect)  
When used in Auto Answer mode, the S0 register must be set with to a  
value of either 3 or 4. This ensures:  
a person calling your modem will hear a short burst of ringing before  
the modem answers. This confirms that the call has been  
successfully switched through the network.  
caller identification information (which occurs between the first and  
second ring cadences) is not destroyed.  
The preferred method of dialing is to use DTMF tones (ATDT...) as this  
is faster and more reliable than pulse (decadic) dialing. If for some  
reason you must use decadic dialing, your communications program  
must be set up to record numbers using the following translation table  
as this modem does not implement the New Zealand “Reverse Dialing”  
standard.  
Number to be dialed: 0 1 2 3 4 5 6 7 8 9  
Number to program into computer: 0 9 8 7 6 5 4 3 2 1  
Note that where DTMF dialing is used, the numbers should be  
entered normally.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
xii  
The transmit level from this device is set at a fixed level and because of  
this there may be circumstances where the performance is less than  
optimal. Before reporting such occurrences as faults, please check the  
line with a standard Telepermitted telephone, and only report a fault if  
the phone performance is impaired.  
It is recommended that this equipment be disconnected from the  
Telecom line during electrical storms.  
When relocating the equipment, always disconnect the Telecom line  
connection before the power connection, and reconnect the power first.  
This equipment may not be compatible with Telecom Distinctive Alert  
cadences and services such as FaxAbility.  
NOTE THAT FAULT CALLOUTS CAUSED BY ANY OF THE ABOVE  
CAUSES MAY INCUR A CHARGE FROM TELECOM  
General conditions  
As required by PTC 100, please ensure that this office is advised of any  
changes to the specifications of these products which might affect  
compliance with the relevant PTC Specifications.  
The grant of this Telepermit is specific to the above products with the  
marketing description as stated on the Telepermit label artwork. The  
Telepermit may not be assigned to other parties or other products without  
Telecom approval.  
A Telepermit artwork for each device is included from which you may  
prepare any number of Telepermit labels subject to the general instructions  
on format, size and color on the attached sheet.  
The Telepermit label must be displayed on the product at all times as proof  
to purchasers and service personnel that the product is able to be  
legitimately connected to the Telecom network.  
The Telepermit label may also be shown on the packaging of the product  
and in the sales literature, as required in PTC 100.  
The charge for a Telepermit assessment is $337.50. An additional charge  
of $337.50 is payable where an assessment is based on reports against  
non-Telecom New Zealand Specifications. $112.50 is charged for each  
variation when submitted at the same time as the original.  
An invoice for $NZ1237.50 will be sent under separate cover.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
xiii  
Following information is only for EU-member states:  
Disposal of products  
The crossed out wheeled dust bin symbol indicates that products must be  
collected and disposed of separately from household waste. Integrated  
batteries and accumulators can be disposed of with the product. They will  
be separated at the recycling centres.  
The black bar indicates that the product was placed on the market after  
August 13, 2005.  
By participating in separate collection of products and batteries, you will  
help to assure the proper disposal of products and batteries and thus help  
to prevent potential negative consequences for the environment and human  
health.  
For more detailed information about the collection and recycling  
programmes available in your country, please visit our website  
(http://eu.computers.toshiba-europe.com) or contact your local city office or  
the shop where you purchased the product.  
Disposal of batteries and/or accumulators  
The crossed out wheeled dust bin symbol indicates that batteries and/or  
accumulators must be collected and disposed of separately from household  
waste.  
If the battery or accumulator contains more than the specified values of lead  
(Pb), mercury (Hg), and/or cadmium (Cd) defined in the Battery Directive  
3Eꢀꢁ+Jꢀ&Gꢁ  
(2006/66/EC), then the chemical symbols for lead (Pb), mercury (Hg) and/or  
cadmium (Cd) will appear below the crossed out wheeled dust bin symbol.  
By participating in separate collection of batteries, you will help to assure  
the proper disposal of products and batteries and thus help to prevent  
potential negative consequences for the environment and human health.  
For more detailed information about the collection and recycling  
programmes available in your country, please visit our website  
(http://eu.computers.toshiba-europe.com) or contact your local city office or  
the shop where you purchased the product.  
This symbol may not be displayed depending on the country and region  
where you purchased.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
xiv  
 
Disposing of the computer and the computer's batteries  
Discard this computer in accordance with applicable laws and  
regulations. For further information, contact your local government.  
This computer contains rechargeable batteries. After repeated use, the  
batteries will finally lose their ability to hold a charge and you will need  
to replace them. Under certain applicable laws and regulation, it may be  
illegal to dispose of old batteries by placing them in the trash.  
Please be kind to our shared environment. Check with your local  
government authority for details regarding where to recycle old batteries  
or how to dispose of them properly. This product contains mercury.  
Disposal of this material may be regulated due to environmental  
considerations. For disposal, reuse or recycling information, please  
contact your local government.  
ENERGY STAR® Program  
®
Your Computer model may be ENERGY STAR compliant. If the model you  
purchased is compliant, it is labeled with the ENERGY STAR logo on the  
computer and the following information applies.  
TOSHIBA is a partner in the ENERGY STAR Program and has designed  
this computer to meet the latest ENERGY STAR guidelines for energy  
efficiency. Your computer ships with the power management options preset  
to a configuration that will provide the most stable operating environment  
and optimum system performance for both AC power and battery modes.  
To conserve energy, your computer is set to enter the low-power Sleep  
mode which shuts down the system and display within 15 minutes of  
inactivity in AC power mode. TOSHIBA recommends that you leave this  
and other energy saving features active, so that your computer will operate  
at its maximum energy efficiency. You can wake the computer from Sleep  
mode by pressing the power button.  
Products that earn the ENERGY STAR prevent greenhouse gas emissions  
by meeting strict energy efficiency guidelines set by the US EPA and the EU  
Commission. According to the EPA, a computer meeting the new ENERGY  
STAR specifications will use between 20% and 50% less energy depending  
on how it is used.  
Visit http://www.eu-energystar.org or http://www.energystar.gov for more  
information regarding the ENERGY STAR Program.  
Optical disc drive standards  
TOSHIBA Satellite L550/Satellite Pro L550/Satellite L550D/Satellite Pro  
L550D series computer is shipped with one of the following drives  
preinstalled: DVD Super Multi (+-R DL) drive, DVD Super Multi (+-R DL)/w  
Label Flash drive or BD Writer drive.  
The drive has one of the following labels:  
CLASS 1 LASER PRODUCT  
LASER KLASSE 1  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
xv  
 
LUOKAN 1 LASERLAITE  
APPAREIL A LASER DE CLASSE1  
KLASS 1 LASER APPARAT  
Before it is shipped, the Class 1 Laser is certified to meet the United States  
Chapter 21 Standards of the Department of Health and Human Services  
(DHHS 21 CFR).  
For any other country, the drive is certified to meet the Class 1 Laser  
standards of IEC825 and EN60825.  
Optical disc drive safety instructions  
The drive employs a laser system. To ensure proper use of this  
product, please read this instruction manual carefully and retain for  
future reference.  
Should the unit ever require maintenance, contact an authorized  
service location.  
Use of controls, adjustments or the performance of procedures other  
than those specified may result in hazardous radiation exposure  
To prevent direct exposure to the laser beam, do not try to open the  
enclosure.  
DVD Super Multi (+-R DL) drive  
Panasonic UJ890AD/UJ890ED  
Location of the required label  
COMPLIES WITH FDA RADIATION  
PERFORMANCE STANDARDS, 21  
CFR SUBCHAPTER J.  
MANUFACTURED  
Panasonic Communications Co., Ltd.  
1-62, 4-Chome Minoshima  
Hakata-ku Fukuoka, Japan  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
xvi  
HLDS GT20N/GT20F  
Location of the required label  
COMPLIES WITH FDA RADIATION  
PERFORMANCE STANDARDS, 21  
CFR SUBCHAPTER J.  
MANUFACTURED  
Hitachi-LG Data Storage, Inc.  
22-23, Kaigan 3-chome, Minato-Ku,  
Tokyo, 108-0022 Japan  
Toshiba Samsung TS-L633C/TS-L633Y  
Location of the required label  
PRODUCT IS CERTIFIED BY THE  
MANUFACTURER TO COMPLY WITH  
DHHS RULES 21 CFR CHAPTER 1,  
SUBCHAPTER J, APPLICABLE AT  
THE DATE OF MANUFACTURE.  
MANUFACTURED  
Toshiba Samsung Storage Technology  
Korea Corporation  
416, Maetan-3Dong, Yeongtong-Gu,  
Suwon City, Gyeonggi-Do, 443-742,  
Korea  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
xvii  
BD Writer Drive  
Panasonic UJ240EB  
The BD Writer drive employs a laser system. To ensure proper use of  
this product, please read this instruction manual carefully and retain for  
future reference. Should the unit ever require maintenance, contact an  
authorized service location.  
Use of controls, adjustments or the performance of procedures other  
than those specified may result in hazardous radiation exposure.  
To prevent direct exposure to the laser beam, do not try to open the  
enclosure.  
Location of the required label  
COMPLIES WITHFDA RADIATION  
PERFORMANCE STANDARDS, 21  
CFR SUBCHAPTER J  
MANUFACTURED  
Panasonic Communications Co., Ltd.  
1-62, 4-Chome Minoshima Hakata-Ku  
Fukuoka, Japan  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
xviii  
BD Combo  
TM  
Panasonic UJ141EB/BD-R/RE UJ240EB with Labelflash  
The BD Combo/BD-R/RE drive employs a laser system. To ensure  
proper use of this product, please read this instruction manual carefully  
and retain for future reference. Should the unit ever require  
maintenance, contact an authorized service location.  
Use of controls, adjustments or the performance of procedures other  
than those specified may result in hazardous radiation exposure.  
To prevent direct exposure to the laser beam, do not try to open the  
enclosure.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
xix  
TEAC  
DVD Super Multi DV-W28S-V  
The DVD Super Multi drive employs a laser system. To ensure proper  
use of this product, please read this instruction manual carefully and  
retain for future reference. Should the unit ever require maintenance,  
contact an authorized service location.  
Use of controls, adjustments or the performance of procedures other  
than those specified may result in hazardous radiation exposure.  
To prevent direct exposure to the laser beam, do not try to open the  
enclosure.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
xx  
International precautions  
CAUTION: This appliance contains a  
laser system and is classified as a  
“CLASS 1 LASER PRODUCT.” To use  
this model properly, read the instruction  
manual carefully and keep this manual  
for your future reference. In case of any  
trouble with this model, please contact  
your nearest “AUTHORIZED service  
station.” To prevent direct exposure to the  
laser beam, do not try to open the  
enclosure.  
VORSICHT: Dieses Gerät enthält ein  
Laser-System und ist als  
“LASERSCHUTZKLASSE 1 PRODUKT”  
klassifiziert. Für den richtigen Gebrauch  
dieses Modells lesen Sie bitte die  
Bedienungsanleitung sorgfältig durch  
und bewahren diese bitte als Referenz  
auf. Falls Probleme mit diesem Modell  
auftreten, benachrichtigen Sie bitte die  
nächste “autorisierte Service-Vertretung”.  
Um einen direkten Kontakt mit dem  
Laserstrahl zu vermeiden darf das Gerät  
nicht geöffnet werden.  
ADVARSEL: Denne mærking er anbragt  
udvendigt på apparatet og indikerer, at  
apparatet arbejder med laserstråler af  
klasse 1, hviket betyder, at der anvendes  
laserstrlier af svageste klasse, og at man  
ikke på apparatets yderside kan bilve  
udsat for utilladellg kraftig stråling.  
APPARATET BOR KUN ÅBNES AF  
FAGFOLK MED SÆRLIGT KENDSKAB  
TIL APPARATER MED  
LASERSTRÅLER!  
Indvendigt i apparatet er anbragt den her  
gengivne advarselsmækning, som  
advarer imod at foretage sådanne  
indgreb i apparatet, at man kan komme til  
at udsatte sig for laserstråling.  
User’s Manual  
xxi  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
OBS! Apparaten innehåller  
laserkomponent som avger laserstråining  
överstigande gränsen för laserklass 1.  
VAROITUS. Suojakoteloa si saa avata.  
Laite sisältää laserdiodin, joka lähetää  
näkymätöntä silmilie vaarallista  
lasersäteilyä.  
CAUTION: USE OF CONTROLS OR  
ADJUSTMENTS OR PERFORMANCE  
OF PROCEDURES OTHER THAN  
THOSE SPECIFIED IN THE OWNER’S  
MANUAL MAY RESULT IN  
HAZARDOUS RADIATION EXPOSURE.  
VORSICHT: DIE VERWENDUNG VON  
ANDEREN STEURUNGEN ODER  
EINSTELLUNGEN ODER DAS  
DURCHFÜHREN VON ANDEREN  
VORGÄNGEN ALS IN DER  
BEDIENUNGSANLEITUNG  
BESCHRIEBEN KÖNNEN  
GEFÄHRLICHE  
STRAHLENEXPOSITIONEN ZUR  
FOLGE HABEN.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
xxii  
FCC information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii  
Modem warning notice. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vi  
Japan regulations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vi  
Instructions for IC CS-03 certified equipment . . . . . . . . . . . . . . . . . . . . x  
Notes for Users in Australia and New Zealand . . . . . . . . . . . . . . . . . . xi  
Following information is only for EU-member states: . . . . . . . . . . . xiv  
Optical disc drive standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xv  
International precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xxi  
Preface  
Stress injury . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xxxi  
Heat injury. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xxxi  
Pressure or impact damage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xxxi  
PC Card overheating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xxxi  
Mobile phones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xxxii  
Instruction Manual for Safety and Comfort . . . . . . . . . . . . . . . . . . . xxxii  
Chapter 1 Introduction  
Equipment checklist. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1  
Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3  
Special features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-12  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
xxiii  
Chapter 3 Getting Started  
Starting up for the first time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7  
Chapter 4 Operating Basics  
Media care. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-22  
Modem. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-31  
Wireless communications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-34  
LAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-37  
Cleaning the computer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-39  
Moving the computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-40  
Heat dispersal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-40  
Chapter 5 The Keyboard  
Typewriter keys. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1  
Function keys: F1 … F9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2  
Soft keys: FN key combinations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
xxiv  
Chapter 6 Power and Power-up Modes  
Chapter 8 Optional Devices  
PC Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2  
Chapter 9 Troubleshooting  
Chapter 10 Disclaimers  
CPU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1  
Memory (Main System) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-2  
Battery Life . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-3  
HDD drive capacity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-3  
LCD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-3  
Graphics Processor Unit ("GPU”). . . . . . . . . . . . . . . . . . . . . . . . . . . 10-3  
Wireless LAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-4  
External HDD Capacity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-4  
Non-applicable Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-4  
Copy Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-4  
Images . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-4  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
xxv  
Appendix A Specifications  
Appendix C V.90/V.92  
Appendix D Wireless LAN  
Card Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-1  
Radio Characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-2  
Supported Frequency Sub-bands. . . . . . . . . . . . . . . . . . . . . . . . . . . . D-2  
Appendix E AC Power Cord and Connectors  
Certification agencies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-2  
Appendix F TOSHIBA PC Health Monitor  
Starting the TOSHIBA PC Health Monitor. . . . . . . . . . . . . . . . . . . . . . F-2  
Glossary  
Index  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
xxvi  
Preface  
Congratulations on your purchase of the TOSHIBA Satellite L550/Satellite  
Pro L550/Satellite L550D/Satellite Pro L550D series computer. This  
powerful notebook computer provides excellent expansion capability,  
includes multimedia functionality, and is designed to provide years of  
reliable, high-performance computing.  
This manual tells how to set up and begin using your TOSHIBA Satellite  
L550/Satellite Pro L550/Satellite L550D/Satellite Pro L550D series  
computer. It also provides detailed information on configuring your  
computer, basic operations and care, using optional devices and  
troubleshooting.  
If you are a new user of computers or if you’re new to portable computing,  
first read over the Introduction and The Grand Tour chapters to familiarize  
yourself with the computer’s features, components and accessory devices.  
Then read Getting Started for step-by-step instructions on setting up your  
computer.  
If you are an experienced computer user, please continue reading the  
preface to learn how this manual is organized, then become acquainted  
with this manual by browsing through its pages. Be sure to read the Special  
features section of the Introduction, to learn about features that are  
uncommon or unique to the computers and carefully read HW Setup and  
Passwords. If you are going to install PC Cards or connect external devices  
such as a printer, be sure to read Chapter 8, Optional Devices.  
Manual contents  
This manual is composed of the following chapters, appendixes, a glossary  
and an index.  
Chapter 1, Introduction, is an overview of the computer’s features,  
capabilities, and options.  
Chapter 2, The Grand Tour, identifies the components of the computer and  
briefly explains how they function.  
Chapter 3, Getting Started, provides a quick overview of how to begin  
operating your computer.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
xxvii  
   
Preface  
Chapter 4, Operating Basics, includes tips on care of the computer and on  
using the touchpad, optical disc drive, Audio/Video controls, the web camera,  
the microphone, the internal modem, wireless communication and LAN.  
Chapter 5, The Keyboard, describes special keyboard functions including the  
hot keys.  
Chapter 6, Power and Power-up Modes, gives details on the computer’s  
power resources and battery save modes.  
Chapter 7, HW Setup and Passwords, explains how to configure the  
computer using the HW Setup program. It also tells how to set a password.  
Chapter 8, Optional Devices, describes the optional hardware available.  
Chapter 9, Troubleshooting, provides helpful information on how to perform  
some diagnostic tests, and suggests courses of action if the computer  
doesn’t seem to be working properly.  
Chapter 10 Disclaimers, provides Legal Footnotes information related to your  
computer.  
The Appendixes provide technical information about your computer.  
The Glossary defines general computer terminology and includes a list of  
acronyms used in the text.  
The Index quickly directs you to the information contained in this manual.  
Conventions  
This manual uses the following formats to describe, identify, and highlight  
terms and operating procedures.  
Abbreviations  
On first appearance, and whenever necessary for clarity, abbreviations are  
enclosed in parentheses following their definition. For example: Read Only  
Memory (ROM). Acronyms are also defined in the Glossary.  
Icons  
Keys  
Icons identify ports, dials, and other parts of your computer. The indicator  
panel also uses icons to identify the components it is providing information  
on.  
The keyboard keys are used in the text to describe many computer  
operations. A distinctive typeface identifies the key top symbols as they  
appear on the keyboard. For example, ENTER identifies the ENTER key.  
Key operation  
Some operations require you to simultaneously use two or more keys. We  
identify such operations by the key top symbols separated by a plus sign (+).  
For example, CTRL + C means you must hold down CTRL and at the same  
time press C. If three keys are used, hold down the first two and at the same  
time press the third.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
xxviii  
 
Preface  
When procedures require an action such as  
ABC  
clicking an icon or entering text, the icon's name  
or the text you are to type in is represented in the  
typeface you see to the left.  
Display  
Names of windows or icons or text generated by  
the computer that appear on its display screen  
are presented in the type face you see to the left.  
ABC  
Messages  
Messages are used in this manual to bring important information to your  
attention. Each type of message is identified as shown below.  
Pay attention! A caution informs you that improper use of equipment or  
failure to follow instructions may cause data loss or damage your  
equipment.  
Please read. A note is a hint or advice that helps you make best use of  
your equipment.  
Indicates a potentially hazardous situation, which could result in death or  
serious injury, if you do not follow instructions.  
Terminology  
This term is defined in this document as follows:  
Start  
The word "Start" refers to the "  
Windows 7.  
" button in  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
xxix  
General Precautions  
TOSHIBA computers are designed to optimize safety, minimize strain and  
withstand the rigors of portability. However, certain precautions should be  
observed to further reduce the risk of personal injury or damage to the  
computer.  
Be certain to read the general precautions below and to note the cautions  
included in the text of the manual.  
Provide adequate ventilation  
Always make sure your computer and AC adaptor have adequate  
ventilation and are protected from overheating when the power is  
turned on or when an AC adaptor is connected to a power outlet (even if  
your computer is in Sleep Mode). In this condition, observe the  
following:  
Never cover your computer or AC adaptor with any object.  
Never place your computer or AC adaptor near a heat source, such  
as an electric blanket or heater.  
Never cover or block the air vents including those located at the  
base of the computer.  
Always operate your computer on a hard flat surface. Using your  
computer on a carpet or other soft material can block the vents.  
Always provide sufficient space around the computer.  
Overheating your computer or AC adaptor could cause system failure,  
computer or AC adaptor damage or a fire, possibly resulting in serious  
injury.  
Creating a computer-friendly environment  
Place the computer on a flat surface that is large enough for the computer  
and any other items you are using, such as a printer.  
Leave enough space around the computer and other equipment to provide  
adequate ventilation. Otherwise, they may overheat.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
xxx  
     
General Precautions  
To keep your computer in prime operating condition, protect your work area  
from:  
Dust, moisture, and direct sunlight.  
Equipment that generates a strong electromagnetic field, such as  
stereo speakers (other than speakers that are connected to the  
computer) or speakerphones.  
Rapid changes in temperature or humidity and sources of temperature  
change such as air conditioner vents or heaters.  
Extreme heat, cold, or humidity.  
Liquids and corrosive chemicals.  
Stress injury  
Carefully read the Instruction Manual for Safety and Comfort. It contains  
information on the prevention of stress injuries to your hands and wrists  
that can be caused by extensive keyboard use.  
Heat injury  
Avoid prolonged physical contact with the computer. If the computer is  
used for long periods, its surface can become very warm. While the  
temperature will not feel hot to the touch, if you maintain physical  
contact with the computer for a long time, for example if you rest the  
computer on your lap or if you keep your hands on the palm rest, your  
skin might suffer a low-heat injury.  
If the computer has been used for a long time, avoid direct contact with  
the metal plate supporting the various interface ports as this can  
become hot.  
The surface of the AC adaptor can become hot when in use but this  
condition does not indicate a malfunction. If you need to transport the  
AC adaptor, you should disconnect it and let it cool before moving it.  
Do not lay the AC adaptor on a material that is sensitive to heat as the  
material could become damaged.  
Pressure or impact damage  
Do not apply heavy pressure to the computer or subject it to any form of  
strong impact as this can damage the computer's components or otherwise  
cause it to malfunction.  
PC Card overheating  
Some PC Cards can become hot during prolonged use which may result in  
errors or instability in the operation of the device in question. In addition,  
you should also be careful when you remove a PC Card that has been  
used for a long time.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
xxxi  
       
General Precautions  
Mobile phones  
Please be aware that the use of mobile phones can interfere with the audio  
system. The operation of the computer will not be impaired in any way, but  
it is recommended that a minimum distance of 30cm is maintained between  
the computer and a mobile phone that is in use.  
Instruction Manual for Safety and Comfort  
All important information on the safe and proper use of this computer is  
described in the enclosed Instruction Manual for Safety and Comfort. Be  
sure to read it before using the computer.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
xxxii  
   
Chapter 1  
Introduction  
This chapter provides an equipment checklist, and it identifies the  
computer’s features, options and accessories.  
Some of the features described in this manual may not function properly if  
you use an operating system that was not pre-installed by TOSHIBA.  
Equipment checklist  
Carefully unpack your computer, taking care to save the box and packaging  
materials for future use.  
Hardware  
Check to make sure you have all the following items:  
TOSHIBA Satellite L550/Satellite Pro L550/Satellite L550D/Satellite Pro  
L550D series Portable Personal Computer  
AC adaptor and power cord (2-pin plug or 3-pin plug)  
Battery pack (is pre-installed in some computer)  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1-1  
         
Introduction  
Software  
The following Windows operating system and utility software are  
pre-installed.  
Windows 7  
Modem Driver (Can be used only for Modem models)  
Bluetooth Driver (Can be used only for Bluetooth models)  
Display Drivers for Windows  
TOSHIBA Value Added Package  
TOSHIBA Hardware Setup  
TOSHIBA Supervisor Password  
Corel DVD MovieFactory  
WinDVD BD for TOSHIBA  
LAN Driver  
Pointing Device Driver  
Sound Driver for Windows  
Wireless LAN Driver (Can be used only for Wireless LAN models)  
Windows Mobility Center  
TOSHIBA Disc Creator  
TOSHIBA Recovery Media Creator  
TOSHIBA ConfigFreeTM  
TOSHIBA Assist  
TOSHIBA DVD PLAYER  
TOSHIBA Face Recognition (Can be used only Web Camera  
models)  
TOSHIBA PC Health Monitor  
TOSHIBA eco Utility  
Online Manual  
TOSHIBA Satellite L550/Satellite Pro L550/Satellite  
L550D/Satellite Pro L550D series User’s Manual (This manual)  
Documentation  
TOSHIBA Satellite L550/Satellite Pro L550/Satellite L550D/Satellite  
Pro L550D series Portable Personal Computer User’s Manual  
(User’s Manual)  
Instruction Manual for Safety and Comfort  
End User License Agreement  
If any of the items are missing or damaged, contact your dealer  
immediately.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1-2  
 
Introduction  
Features  
This computer incorporates the following features and benefits:  
Processor  
Built-in  
Your computer is equipped with one processor  
and processor type that varies depending on the  
model. To check which type of processor is  
included in your model, open the TOSHIBA PC  
Diagnostic Tool Utility by clicking Start All  
programs TOSHIBA Utilities PC  
Diagnostic Tool.  
Chipset  
Mobile Intel® GM45 Express Chipset  
Mobile Intel® GL40 Express Chipset  
Mobile Intel® HM55 Express Chipset  
or  
AMD M780G Chipset  
AMD M780V Chipset  
AMD M880G Chipset  
AMD M860G Chipset  
AMD M870 Chipset  
User’s Manual  
1-3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Introduction  
Memory  
Slots  
PC3-8500/PC2-6400 1 GB, 2 GB or 4 GB  
memory modules can be installed in the two  
memory slots of below models:  
Mobile Intel® GM45 Express Chipset model  
Mobile Intel® GL40 Express Chipset  
Mobile Intel® HM55 Express Chipset  
AMD M780G Chipset  
AMD M780V Chipset  
AMD M880G Chipset  
AMD M860G Chipset  
AMD M870 Chipset  
Maximum system memory size and speed are  
depending on the model you purchased.  
Maximum size of memory can be installed on Mobile Intel® GL40  
Express Chipset models is 4GB.  
PC2-6400 memory module works as PC2-5300 speed on AMD  
TM  
Athlon/Sempron Processor.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1-4  
 
Introduction  
Video RAM  
Video RAM depends on the model you purchased.  
Mobile Intel® GM45 Express Chipset model/  
Mobile Intel® GL40 Express Chipset model/  
Mobile Intel® HM55 Express Chipset model:  
Video RAM capacity shares with main memory,  
and the proportion depends on Dynamic Video  
Memory Technology.  
Mobile Intel® GM45 Express Chipset model in  
graphic chip by ATI Mobility RadeonTM HD 4530:  
External 256MB  
Mobile Intel® GM45 Express Chipset model in  
graphic chip by ATI Mobility RadeonTM HD 4570:  
External 512MB  
Mobile Intel® GM45 Express Chipset model in  
graphic chip by ATI Mobility RadeonTM HD 4650:  
External 1GB  
Mobile Intel® HM55 Express Chipset model in  
graphic chip by ATI Mobility RadeonTM HD 5145:  
External 512MB  
Mobile Intel® HM55 Express Chipset model in  
graphic chip by ATI Mobility RadeonTM HD 5165:  
External 1GB  
AMD M780G Chipset model/  
AMD M780V Chipset model/  
AMD M880G Chipset model/  
AMD M860G Chipset model:  
Video RAM capacity shares with main memory,  
and the proportion depends on ATI  
HyperMemoryTM  
.
AMD M780G Chipset model/  
AMD M880G Chipset model/  
AMD M870 Chipset model in graphic chip by  
ATI Mobility RadeonTM HD 4530: External 256MB  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1-5  
 
Introduction  
AMD M780G Chipset model/  
AMD M880G Chipset model/  
AMD M870 Chipset model in graphic chip by  
ATI Mobility RadeonTM HD 4570:External 512MB  
AMD M780G Chipset model/  
AMD M880G Chipset model/  
AMD M870 Chipset model in graphic chip by  
ATI Mobility RadeonTM HD 4650: External 1GB  
Disks  
Hard disk drive or  
Solid State drive  
This computer is equipped with the following  
types of Solid State Drive(SSD) and Hard Disk  
Drive (HDD). The capacity of each disk drive  
model is different.  
SSD  
64GB  
128GB  
256GB  
512GB  
HDD  
5400rpm  
120GB  
160GB  
250GB  
320GB  
400GB  
500GB  
640GB  
Please note that part of the hard disk drives  
overall capacity is reserved as administration  
space.  
Additional hard disk drive sizes may be introduced.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1-6  
Introduction  
Optical disc drive  
DVD Super Multi  
drive  
The drive reads DVD-ROM's at a maximum 8x  
speed and CD-ROM's at a maximum 24x speed,  
and writes CD-R's at up to 24x speed, CD-RW's  
at up to 24x speed, DVD-RW's at up to 6x speed,  
DVD-R's, DVD+R's and DVD+RW's at up to 8x  
speed, DVD-R (Dual layer) at up to 6x speed,  
DVD+R (Double Layer) at up to 6x speed and  
DVD-RAM at up to 5x speed, and supports the  
following formats:  
CD-R  
CD-RW  
DVD-ROM  
DVD-Video  
CD-DA  
CD-Text  
Photo CD™ (single/multi-session)  
CD-ROM Mode 1, Mode 2  
CD-ROM XA Mode 2 (Form1, Form2)  
Enhanced CD (CD-EXTRA)  
Addressing Method 2  
DVD-R  
DVD-R (Dual Layer)  
DVD-RW  
DVD+R  
DVD+R (Double Layer)  
DVD+RW  
DVD-RAM  
Some models are equipped with a full-size DVD  
Super Multi drive module that lets you run CD's  
or DVD's without using an adaptor.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1-7  
Introduction  
DVD Super Multi  
The drive reads DVD-ROM's at a maximum 8x  
drive with Labelflash speed and CD-ROM's at a maximum 24x speed,  
and writes CD-R's at up to 24X speed and  
CD-RW's at up to 24X speed. DVD-R's, DVD+R's  
and DVD+RW's at up to 8x speed, DVD-RW's at  
up to 6x speed, DVD-R (Dual Layer) and  
DVD+R (Double Layer) at up to 6x speed,  
DVD-RAM at up to 5x speed. This drive supports  
the same formats as the DVD Super Multi drive.  
BD Writer drive  
The drive reads BD-ROM's at a maximum 6x  
speed and DVD-ROM's at a maximum 8x speed  
and CD-ROM's at a maximum 24x speed, and  
writes CD-R's at up to 24x speed, CD-RW's at up  
to 16x speed, DVD-RW's at up to 6x speed,  
DVD-R's, DVD+R's and DVD+RW's at up to 8x  
speed, DVD-R (Dual layer) at up to 4x speed,  
DVD+R (Double Layer) at up to 4x speed, DVD-  
RAM's at up to 5x speed, BD-R's at up to 6x  
speed, BD-R (DL) at 4x speed, BD-RE's at up to  
2x speed and BD-RE (DL) at up to 2x speed, and  
supports the following formats:  
CD-DA  
CD-ROM  
CD-ROM XA  
PhotoCD (multisession)  
Video CD  
CD-Extra (CD+)  
CD-Text  
Hybrid SACD  
DVD-Video  
DVD-ROM  
DVD-R  
DVD-RW  
DVD-R (DL)  
DVD+R  
DVD+RW  
DVD+R (DL)  
DVD-RAM  
BD-ROM  
BD-R  
BD-RE  
BD-R(DL)  
BD-RE(DL)  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1-8  
Introduction  
Keyboard  
Built-in  
The internal keyboard provides dedicated cursor  
control overlay keys,  
and  
Keys. The  
keyboard is compatible with the IBM® enhanced  
keyboard. Refer to Chapter 5, The Keyboard, for  
details.  
Pointing Device  
Built-in Touch Pad  
The integrated Touch Pad and control buttons in  
the palm rest allow control of the on-screen  
pointer and support functions such as the  
scrolling of windows.  
Power  
Battery pack  
The computer is powered by one rechargeable  
lithium-ion battery pack.  
RTC battery  
AC adaptor  
The internal RTC battery backs up the Real Time  
Clock (RTC) and calendar.  
The AC adaptor provides power to the system  
and recharges the batteries when they are low. It  
comes with a detachable power cord which will  
either have a 2-pin or 3-pin plug enclosure.  
As the AC adaptor is universal, it can receive a  
range of AC voltages from 100 to 240 volts,  
however you should note that the output current  
varies among different models. Using the wrong  
adaptor can damage your computer. Refer to the  
AC adaptor section in Chapter 2, The Grand Tour.  
Ports  
External monitor  
This port provides 15-pin, analog VGA port.This  
port allows you to connect an external monitor to  
the computer. Some models include this feature.  
Universal Serial Bus The computer supports multiple Universal Serial  
(USB 2.0)  
Bus ports that comply with the USB 2.0 standard.  
One of the USB ports has an eSATA (External  
Serial ATA) function.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1-9  
             
Introduction  
Slots  
PC Card  
The internal PC Card slot is a Universal slot. This  
slot supports Type II PC Card and CardBus.  
Bridge media  
This slot lets you insert an SD/SDHC™  
memory card, miniSD/microSDCard,  
Memory Stick® (PRO) and MultiMediaCard.  
Refer to Chapter 8, Optional Devices.  
Multimedia  
Sound system  
The integrated sound system provides support  
for the computer's internal speakers and  
microphone, also allowing an external  
microphone and headphones to be connected  
via the appropriate jacks.  
Web Camera  
Web Camera is a device that allows you to  
record video or take photographs with your  
computer. You can use it for video chatting or  
video conferences using a communication tool  
such as Windows Live Messenger. TOSHIBA  
Web Camera Application will help you to add  
various video effects to your video or photograph.  
HDMI out port  
HDMI out port can connect with Type A  
connector HDMI cable.  
HDMI cable can send video and audio signals.  
Headphone jack  
This jack lets you connect digital speakers or a  
stereo headphone (16 ohm minimum). When you  
connect headphones, the internal speaker is  
automatically disabled.  
Microphone jack  
A 3.5mm mini microphone jack enables  
connection of a three-conductor mini jack for  
stereo microphone input, and connection of a  
stereo device for audio input.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1-10  
           
Introduction  
Communications  
Modem  
Some models are equipped with the integrated  
modem. The integrated modem provides  
capability for data and fax communications that  
support the V.90 (V.92) standards and includes a  
modem jack for connection to the telephone line.  
Please note that both the V.90 and V.92  
standards are only supported in the USA,  
Canada, Germany, UK and France. Only the  
V.90 standard is supported in other regions. You  
should also be aware that the speed of data and  
fax transfer will depend on the analog telephone  
line conditions.  
The integrated model is only installed as a  
standard device in some markets.  
LAN  
The computer has built-in support for Ethernet  
LAN (10 megabits per second, 10BASE-T) and  
Fast Ethernet LAN (100 megabits per second,  
100BASE-TX).  
It is pre-installed as a standard device in some  
markets.  
BluetoothTM  
Some computers in this series have Bluetooth  
wireless communication function which  
eliminates the need for cables between  
electronic devices such as computers and  
printers and mobile phones. When it is enabled,  
Bluetooth provides the wireless personal area  
network environment which is safe and  
trustworthy, that is quick and easy.  
Wireless LAN  
The computers in this series are equipped with a  
Wireless LAN module that is compatible with  
other LAN systems based on Direct Sequence  
Spread Spectrum/Orthogonal Frequency Division  
Multiplexing radio technology that complies with  
the IEEE 802.11 Standard.  
The transmission speed over the wireless LAN, and the distance over  
which the wireless LAN can reach, may vary depending on surrounding  
electromagnetic environment, obstacles, access point design and  
configuration, client design and software/hardware configurations. The  
transmission rate described is the theoretical maximum speed as  
specified under the appropriate standard - the actual transmission  
speed will be lower than the theoretical maximum speed.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1-11  
       
Introduction  
Security  
Security lock slot  
Connects a security lock to anchor the computer  
to a desk or other large object.  
Software  
The computer's internal display panel supports high-resolution video  
graphics and can be set to a wide range of viewing angles for maximum  
comfort and readability.  
Operating system  
Windows 7 is available. Refer to the preinstalled  
Software section at the front of this chapter.  
TOSHIBA Utilities  
A number of utilities and drivers are preinstalled  
to make your computer more convenient to use.  
Refer to the Utilities and applications section in  
this chapter.  
Plug and Play  
When you connect an external device to the  
computer or when you install a component, Plug  
and Play capability enables the system to  
recognize the connection and make the  
necessary configurations automatically.  
Special features  
The following features are either unique to TOSHIBA computers or are  
advanced features which make the computer more convenient to use.  
Access each function using the following procedures.  
* To access the Power Options, click Start Control Panel System  
and Security Power Options.  
Hot keys  
Hot keys are specific key combinations that let  
you quickly change the system configuration  
directly from the keyboard without running a  
system program.  
Display automatic  
This feature automatically cuts off power to the  
computer's display panel when there is no  
keyboard input for a specified time, with power  
being restored the next time a key is pressed.  
This can be specified in the Power Options.  
*
power off  
HDD automatic  
This feature automatically cuts off power to the  
hard disk drive when it is not accessed for a  
specified time, with power being restored when  
the hard disk drive is next accessed. This can be  
specified in the Power Options.  
*
power off  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1-12  
         
Introduction  
System automatic  
Sleep/Hibernation  
This feature automatically shuts down the system  
into either Sleep Mode or Hibernation Mode when  
there is no input or hardware access for a  
specified time. This can be specified in the Power  
Options.  
*
Mode  
Power on password Two levels of password security, supervisor and  
user, are available to prevent unauthorized  
access to your computer.  
Instant security  
A specific hot key function automatically locks the  
system providing data security.  
Intelligent power  
A microprocessor in the computer's intelligent  
power supply detects the battery's charge,  
automatically calculates the remaining battery  
capacity and protects electronic components  
from abnormal conditions such as a voltage  
overload from the AC adaptor. This can be  
specified in the Power Options.  
*
supply  
*
This feature lets you configure the computer in  
order to save battery power. This can be  
specified in the Power Options.  
Battery save mode  
Low battery  
automatic  
When battery power is exhausted to the point that  
computer operation cannot be continued, the  
system automatically enters Hibernation Mode  
and shuts itself down. This can be specified in the  
Power Options.  
*
Hibernation Mode  
*
To protect against overheating, the processor has  
an internal temperature sensor so that, if the  
computer's internal temperature rises to a certain  
level, the cooling fan is turned on or the  
processing speed is lowered. This can be  
specified in the Power Options.  
Heat dispersal  
If the processor's temperature reaches an unacceptably high level with  
either setting, the computer will automatically shut down to prevent any  
damage - in this instance any unsaved data in memory will be lost.  
Hibernation Mode  
This feature lets you turn off the power to the  
computer without exiting from your software. The  
contents of main memory are automatically  
saved to the hard disk drive so that when you  
next turn the power on again, you can continue  
working right where you left off. Refer to the  
Turning off the power section in Chapter 3,  
Getting Started, for more details.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1-13  
         
Introduction  
Sleep Mode  
If you have to interrupt your work, you can use  
this feature to allow you to turn off power to the  
computer without exiting from your software. Data  
is maintained in the computer's main memory so  
that when you next turn on the power, you can  
continue working right where you left off.  
TOSHIBA Value Added Package  
This section describes the TOSHIBA Component features pre-installed on  
the computer.  
TOSHIBA Power  
Saver  
TOSHIBA Power Saver provides you with the  
features of more various power supply  
managements.  
TOSHIBA Zooming  
Utility  
This utility allows you to enlarge or reduce the  
icon size on the Windows Desktop, or the zoom  
factor associated with specific supported  
applications.  
TOSHIBA PC  
Diagnostic Tool  
The TOSHIBA PC Diagnostic Tool will display  
basic system configuration information and allow  
the functionality of some of the computer's built-  
in hardware devices to be tested.  
TOSHIBA Flash  
Cards  
The TOSHIBA Flash Cards provide a quick way  
to modify selected system functions and to  
launch applications.  
Hot key function  
TOSHIBA utility launcher function  
TOSHIBA  
Accessibility  
The TOSHIBA Accessibility utility provides  
support to movement impaired users when they  
need to use the TOSHIBA Hot-key functions. In  
use, the utility allows you to make the FN key  
'sticky', that is you can press it once, release it,  
and they press one of the 'F' keys in order to  
access its specific function. When set, the FN  
key will remain active until another key is  
pressed.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1-14  
       
Introduction  
Utilities and Applications  
This section describes the pre-installed utilities that come with the  
computer and details how to start them. For further information on their  
operation, please refer to each utility's online manual, help files or  
README.TXT file.  
Bluetooth Stack for  
This software enables communication between  
Windows by Toshiba the computer and external Bluetooth devices  
such as printers and mobile phones.  
Bluetooth functions cannot be used in models that do not have a Bluetooth  
module installed.  
TOSHIBA Assist  
TOSHIBA Assist is a graphical user interface that  
provides access to specific tools, utilities and  
applications that make the use and configuration  
of the computer easier.  
HW Setup utility  
To start the utility, click the Windows Start button,  
point to All Programs, click TOSHIBA, click  
Utilities, and select HWSetup.  
TOSHIBA ConfigFree TOSHIBA ConfigFree is a suite of utilities that  
improve the ease and control of communication  
devices and network connections, help in the  
identification of communication problems and  
allow the creation of profiles if you need to switch  
between different locations and communication  
networks. To access this utility, click Start All  
Programs TOSHIBA ConfigFree.  
TOSHIBA Disc  
Creator  
You can create CD's and DVD's in a number of  
formats including audio CD's that can be played  
on a standard CD player, and data CD's/DVD's  
which can store copies of the files and folders on  
your computer's hard disk drive. This software  
can be used on models with a DVD Super Multi  
drive.  
To start this utility, click Start All Programs →  
TOSHIBA CD&DVD Applications Disc  
Creator.  
TOSHIBA DVD-RAM This utility has the function of Physical Format  
Utility  
and Write-Protect to DVD-RAM. This utility is  
contained the setup module of TOSHIBA Disc  
Creator. To start this utility, click Start All  
Programs TOSHIBA CD&DVD  
Applications DVD-RAM Utility.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1-15  
           
Introduction  
Corel DVD  
MovieFactory for  
TOSHIBA  
Corel DVD MovieFactory for TOSHIBA allows  
users to instantly create DVD video or slideshow  
discs via a user-friendly wizard interface with  
specific task oriented features.  
The Labelflash feature is also supported which  
allows text and images to be printed on the label  
surface of Labelflash compatible media without  
using a printer. Some models supports the  
Labelflash function.  
Labelflash features cannot be used in models that do not have a DVD  
Super Multi drive with Labelflash.  
In order to determine if the optical disc drive installed in your computer  
supports Labelflash follow the steps as detailed below:  
1. Click Start All Programs DVD MovieFactory for TOSHIBA →  
DVD MovieFactory Launcher to launch DVD MovieFactory.  
2. Click Create Disc Label. Corel Label@Once is started.  
3. Click the General tab.  
4. Choose optical disc drive for Printer.  
If the drive name is displayed in Step 4, your computer's optical disc drive  
supports Labelflash.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1-16  
Introduction  
WinDVD BD for  
TOSHIBA  
This software is provided for playback of Blu-ray  
Disc. It has an on-screen interface and functions.  
Click Start All Programs InterVideo  
WinDVD WinDVD BD for TOSHIBA.  
Windows Mobility  
Center  
This section describes the Windows Mobility  
Center. Mobility Center is a utility for accessing  
several mobile PC settings quickly in one  
window. A default maximum of eight tiles are  
provided by the operating system, and the  
additional two tiles are added to your Mobility  
Center.  
Lock Computer:  
This can be used to lock your computer without  
turning it off. This has the same function as the  
Lock button at the bottom of the right pane in the  
start menu.  
TOSHIBA Assist:  
This can be used to open TOSHIBA Assist if it is  
already installed in your computer.  
TOSHIBA DVD  
PLAYER  
This software is provided for playback of DVD  
Video.It has an on-screen interface and  
functions. Click Start All Programs →  
TOSHIBA DVD PLAYER.  
Frame dropping, audio skipping or out of synch audio and video may occur  
during playback of some DVD Video titles. Make sure to connect the  
computer's AC adaptor when playing a DVD Video. Power-saving features  
may interfere with smooth playback.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1-17  
Introduction  
TOSHIBA Face  
Recognition  
TOSHIBA Face Recognition uses a face  
verification library to verify the face data of users  
when they log in to Windows. If the verification is  
successful, the user will be logged into Windows  
automatically. The user can thus avoid having to  
enter a password or the like, which makes the  
login process easier.  
TOSHIBA HDD/SSD  
Alert  
The TOSHIBA HDD/SSD Alert includes wizard  
functions to monitor the Disk Drive operating  
status and execute system backup.  
TOSHIBA eco Utility TOSHIBA eco Utility helps you monitor your  
power savings by showing approximate real time  
power consumption. Furthermore, it shows  
approximate accumulated power consumption  
and approximate accumulated power savings  
when using eco mode daily, weekly, and monthly.  
You can track power savings by using eco mode  
continuously.  
Options  
You can add a number of options to make your computer even more  
powerful and convenient to use. The following options are available:  
Memory expansion  
A 1GB, 2GB or 4GB memory module (PC3-8500)  
can easily be installed in the computer.  
Battery Pack  
An additional battery pack can be purchased for  
use as either a spare or replacement. Please  
refer to Chapter 6, Power and Power-up Modes  
for futher information.  
AC Adaptor  
USB FDD  
If you frequently use your computer at more than  
one site, it may be convenient to purchase an  
additional AC adaptor to be kept at each site in  
order to remove the need to always carry the  
adaptor with you.  
The USB floppy diskette drive accommodates  
either a 1.44MB or 720KB floppy diskette through  
connection to one of the computer's USB ports.  
In use, please be aware that, while you cannot  
format 720KB floppy diskettes under Windows®  
7, you are able to read and write to diskettes that  
have already been formatted.  
Security lock  
A slot is available to attach a security cable to the  
computer to deter theft.  
User’s Manual  
1-18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Chapter 2  
The Grand Tour  
This chapter identifies the various components of your computer. Become  
familiar with each component before you operate the computer.  
Front with the display closed  
The following figure shows the computer’s front with its display panel in the  
closed position.  
1
3
2
1. Wireless communication switch  
2. Volume Control  
3. Bridge Media Slot  
Figure 2-1 Front of the computer with display closed  
Wireless  
communication  
switch  
Slide this switch to the right to turn on Wireless  
LAN and Bluetooth functions. Slide it to the left to  
turn off the functions.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2-1  
         
The Grand Tour  
Use this dial to adjust the volume of the internal  
stereo speakers and optional external stereo  
headphones (if connected).  
Volume Control  
Move the Volume control to the left to decrease  
the volume and to the right to increase the  
volume.  
This slot lets you insert an SD/SDHC™  
memory card, miniSD/microSDCard,  
Memory Stick® (PRO) and MultiMediaCard.  
Bridge media slot  
Refer to Chapter 8, Optional Devices.  
Keep foreign metal objects, such as screws, staples and paper clips, out of  
the Bridge media slot. Foreign metal objects can create a short circuit,  
which can cause damage and fire, possibly resulting in serious injury.  
Left side  
The following figure shows the computer's left side.  
1
3
5
7
4
2
6
8
1. Cooling vents  
2. External monitor port  
3. LAN jack  
*4. HDMI out port  
*5. PC Card slot  
6. eSATA/USB combo port  
7. Microphone jack  
8. Headphone jack  
*Depending on the model you purchased.  
Figure 2-2 The left side of the computer  
Cooling vents  
The cooling vents help keep the processor from  
overheating.  
User’s Manual  
2-2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
The Grand Tour  
Do not block the cooling vents. Keep foreign metal objects, such as  
screws, staples and paper clips, out of the cooling vents. Foreign metal  
objects can create a short circuit, which can cause damage and fire,  
possibly resulting in serious injury.  
External monitor  
port  
This port allows you to connect an external  
monitor to the computer.  
LAN jack  
This jack lets you connect to a LAN. The adaptor  
has built-in support for Ethernet LAN (10  
megabits per second, 10BASE-T) and Fast  
Ethernet LAN (100 megabits per second,  
100BASE-TX). The LAN has two indicators.  
Refer to Chapter 4, Operating Basics, for details.  
Do not connect any cable other than a LAN cable to the LAN jack. It  
could cause damage or malfunction.  
Do not connect the LAN cable to a power supply. It could cause  
damage or malfunction.  
HDMI out port  
PC Card slot  
HDMI out port can connect with Type A  
connector HDMI cable.One HDMI cable can  
send video and audio signals.  
This slot allows you to install a single PC Card  
device. A PC Card slot is an optional device on  
some models.  
Keep foreign metal objects, such as screws, staples and paper clips, out of  
the PC Card slot. Foreign metal objects can create a short circuit, which  
can cause damage and fire, possibly resulting in serious injury.  
eSATA/USB combo  
port  
This is a combination port. It is a Universal Serial  
Bus port, complying to the USB 2.0 Standard. It  
also has an eSATA (External Serial ATA) function.  
Microphone jack  
A 3.5 mm mini microphone jack enables  
connection of a three-conductor mini jack for  
monaural microphone input, and connection of a  
stereo device for audio input.  
Headphone jack  
A 3.5 mm mini headphone jack that lets you  
connect digital speakers or a stereo headphone  
(16 ohm minimum). When you connect  
headphones, the internal speaker is  
automatically disabled.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2-3  
       
The Grand Tour  
Right side  
The following figure shows the computer’s right side.  
1
3
5
2
4
1. Optical disc drive  
2. Universal Serial Bus (USB 2.0) port  
*3. Modem jack  
4. DC IN 19V jack  
5. Security lock slot  
*Depending on the model you purchased.  
Figure 2-3 The right side of the computer  
Optical disc drive  
The computer is configured with a tray version of  
the DVD Super Multi drive. The full-size drive  
provides high-performance execution of  
CD/DVD/BD-ROM-based programs.  
Universal Serial Bus Two Universal Serial Bus ports, which comply  
(USB 2.0) port  
with the USB 2.0 standard, are provided on the  
right side of the computer.  
Modem jack  
The modem jack allows you use to attach a  
modular cable in order to connect the internal  
modem directly to a telephone line.  
Some models are equipped with a built-in  
modem.  
Connection to any communication line other than an analog phone line  
could cause a computer system failure.  
Connect the built-in modem only to ordinary analog phone lines.  
Never connect the built-in modem to a digital line (ISDN).  
Never connect the built-in modem to the digital connector on a  
public telephone or to a digital private branch exchange (PBX).  
Never connect the built-in modem to a key telephone system for  
residences or offics.  
Avoid using your computer modem with the telephone cable connected  
during an electrical storm. There may be a remote risk of electric shock  
from lightning.  
User’s Manual  
2-4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
The Grand Tour  
DC IN 19V jack  
The AC adaptor connects to this jack in order to  
power the computer and charge its internal  
batteries. Please note that you should only use  
the model of AC adaptor supplied with the  
computer at the time of purchase - using the  
wrong AC adaptor can cause damage to the  
computer.  
Security lock slot  
A security cable can be attached to this slot and  
then connected to a desk or other large object in  
order to deter theft of the computer.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2-5  
 
The Grand Tour  
Underside  
The following figure shows the underside of the computer. You should  
ensure that the display is closed before the computer is turned over to  
avoid causing any damage.  
1
2
3
6
4
5
1
2
3
6
4
5
1. Battery safety lock  
2. Battery  
3. Battery release latch  
4. Cooling vent  
5. Memory module slots  
6. Hard Disk Drive  
Figure 2-4 The underside of the computer  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2-6  
 
The Grand Tour  
Battery safety lock  
Battery pack  
Slide this latch into its 'Unlock' position in order to  
release the battery pack and prepare for removal.  
1
The battery pack provides power to the computer  
when the AC adaptor is not connected. For more  
detailed information on the use and operation of  
the battery pack please refer to Chapter 6, Power  
and Power-up Modes.  
Battery release latch Slide and hold this latch into its 'Unlock' position  
2
in order to release the battery pack.  
For more detailed information on removing the  
battery pack please refer to Chapter 6, Power  
and Power-up Modes.  
Cooling vents  
Hard disk drive  
The computer's cooling vents help keep the  
processor from overheating.  
The hard disk drive contains the main storage for  
the computer. Disk size varies depending on the  
model purchased.  
Memory module  
slots  
The memory module slots are located here. The  
memory module slots allow for the installation,  
replacement and removal of additional memory  
modules. Please refer to the Additional memory  
module section in Chapter 8, Optional Devices  
for more information.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2-7  
     
The Grand Tour  
Front with the display open  
This section shows the computer with the display panel open. In order to  
open the display, lift the display panel up and position it at a comfortable  
viewing angle for you.  
9
11 10 12  
13  
8
3
1
7
14  
2
3
6
4
5
1. Display screen  
2. Power button  
3. Stereo speakers  
4. Touchpad  
5. Touchpad control buttons  
6. System Indicators  
*7. Front operation panel  
8. Display hinge  
*9. Microphone  
*10. Web Camera  
*11. Web Camera LED  
12. LCD Sensor switch (Not shown)  
13. Wireless LAN antenna (Not shown)  
14. Bluetooth antenna (Not shown)  
* Depending on the model you purchased  
Figure 2-5 The front of the computer with the display open  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2-8  
   
The Grand Tour  
Display screen  
Please be aware that, when the computer is  
operating on the AC adaptor, the image  
displayed on the internal screen will be  
somewhat brighter than when it operates on  
battery power. This difference in brightness  
levels is intended to save power when operating  
on batteries. For more information on the  
computer's display, please refer to the Display  
Controller section in Appendix B.  
Power button  
Press this button to turn the computer's power on  
and off.  
Stereo speakers  
The speakers emit sound generated by your  
software as well as audio alarms, such as low  
battery condition, generated by the system.  
Keep foreign objects out of the speakers. Never allow metal objects, such  
as screws, staples and paper clips, to enter the computer or keyboard.  
Foreign metal objects can create a short circuit, which can cause computer  
damage and fire, possibly resulting in serious injury.  
Touch Pad  
The Touch Pad mouse control device located in  
the center of the palm rest is used to control the  
movement of the on-screen pointer. For more  
information, please refer to the Using the Touch  
Pad section in Chapter 4, Operating Basics.  
Touch Pad control  
buttons  
The control buttons located below the Touch Pad  
allow you to select menu items or manipulate text  
and graphics as designated by the on-screen  
pointer.  
System indicators  
These LED indicators allow you to monitor the  
status of various computer functions and are  
described in more detail within the System  
indicators section.  
Front operation  
panel (four buttons)  
Four buttons are available for use:  
Play/Pause, Previous, Next, Mute.  
These buttons allow you to manage audio/video,  
run applications and access utilities.  
Display hinge  
The display hinge allows the display panel to be  
position at a variety of easy-to-view angles.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2-9  
     
The Grand Tour  
Microphone  
Web Camera  
A built-in microphone allows you to import and  
record sounds for your application - please refer  
to the Sound system section in Chapter 4,  
Operating Basics for more information. Some  
models are equipped with a microphone.  
The Web Camera is a device that allows you to  
record video or take photographs with your  
computer. You can use it for video chatting or  
video conferences using a communication tool  
such as Windows Live Messenger. TOSHIBA  
Web Camera Application will help you to add  
various video effects to your video or photograph.  
The web camera also enables the transmission  
of video and use of video chat via the internet  
using specialized applications.  
The effective pixel count for this web camera is  
0.3 million or 1.0 million (0.3M maximum  
photograph size: 640X480 pixels; 1.0M  
maximum photograph size: 1280X800 pixels).  
Please remove the protective plastic-film before  
using the Web Camera.  
Please refer to the Using the web camera section  
in Chapter 4, Operating Basics. Some models  
are equipped with a Web Camera.  
Web Camera LED  
The Web Camera LED glows when the Web  
Camera is operating.  
Please remove the protective plastic-film before  
using the Web Camera.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2-10  
 
The Grand Tour  
Function buttons  
Some models provide four buttons next to the power button: Play/Pause,  
Previous, Next, Mute.  
Figure 2-6 Front operation panel  
These buttons allow you to manage audio/video, run applications and  
access utilities. Refer to the Function buttons section in Chapter 4,  
Operating Basics for details.  
Please handle your computer carefully to avoid scratching or damaging the  
surface.  
Play/Pause button  
Press this button to begin playing an audio CD, a  
DVD movie or digital audio files. This button also  
acts as a Pause button.  
Previous button  
Next button  
Press this button to advance to the previous  
track, chapter or data.  
Press this button to advance to the next track,  
chapter or data.  
Mute button  
Press this button to turn the sound on and off.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2-11  
 
The Grand Tour  
System indicators  
The LED system indicators for specific computer operations glow when  
those operations are in progress.  
Figure 2-7 System indicators  
DC IN  
The DC IN indicator normally glows green when  
power is being correctly supplied from the AC  
power adaptor. However, If the output voltage  
from the adaptor is abnormal, or if the computer's  
power supply malfunctions, this indicator will go  
out.  
Power  
Battery  
the computer is turned on. However, if you turn  
the computer off into Sleep Mode, this indicator  
will flash amber - approximately one second on,  
two seconds off - both while the system is  
shutting down and while it remains turned off.  
The Battery indicator shows the condition of the  
battery's charge - green indicates the battery is  
fully charged, amber indicates the battery is  
charging, and flashing amber indicates a low  
battery condition. Please refer to Chapter 6,  
Power and Power-up Modes for more information  
on this feature.  
HDD/ODD/eSATA  
Bridge media slot  
The HDD/ODD/eSATA indicator glows green  
whenever the computer is accessing the built-in  
hard disk drive or the other drives. It glows amber  
when the ODD is loading a CD or DVD disc.  
The Bridge media slot indicator glows green  
when the computer is accessing the Bridge  
media slot.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2-12  
               
The Grand Tour  
Keyboard indicators  
The following figures show the positions of the CAPS LOCK indicator and  
the NUM LOCK indicator.  
Figure 2-8 Keypad indicators  
CAPS LOCK  
NUM LOCK  
This indicator glows green when letter keys are  
locked into their uppercase format.  
When the Number Lock indicator lights green,  
you can use the numeric functions of the right  
side of the keyboard. When switched off, the  
keys alternate commands will be enabled.  
Please refer to Chapter 5, The Keyboard for  
more information.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2-13  
The Grand Tour  
Optical disc drives  
The computer is configured with a DVD Super Multi drive or BD writer or  
BD-Combo drive. A Serial ATA interface controller is used for 12cm (4.72")  
and 8cm (3.15") CD/DVD/BD operation. When the computer is accessing a  
CD/DVD/BD, an indicator on the drive glows. For further information on  
loading and unloading discs, please refer to the Writing CD/DVD/BD on  
DVD Super Multi drives or BD Writer drives or BD Combo drives section in  
Chapter 4, Operating Basics.  
Region codes for BD media  
BD is manufactured according to the specifications of three marketing  
regions. When you purchase BD-Video, make sure it matches your player,  
otherwise it will not play properly.  
Code  
A
Region  
Canada, United States, Japan, Southeast Asia,  
East Asia, Central America, South Americ  
B
C
Europe, Australia, New Zealand, Middle East,  
Africa  
China, India, Russia, Mongolia, Indian  
Subcontinent  
Region codes for DVD drives and media  
DVD Super Multi drives and their associated media are manufactured  
according to the specifications of six marketing regions. When you  
purchase DVD-Video, make sure it matches your drive, otherwise it will not  
play properly.  
Code  
Region  
1
2
3
4
Canada, United States  
Japan, Europe, South Africa, Middle East  
South East Asia, East Asia  
Australia, New Zealand, Pacific Islands, Central  
America, South America, Caribbean  
5
6
Russia, Indian Subcontinent, Africa, North Korea,  
Mongolia  
China  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2-14  
 
The Grand Tour  
Writable discs  
This section describes the types of writable CD/DVD/BD discs. Check the  
specifications of your drive to see the types of discs it can write. Use  
TOSHIBA Disc Creator to write compact discs. Please refer to Chapter 4,  
Operating Basics for further information.  
CDs  
CD-R discs can be written only once. The recorded data cannot be  
erased or changed.  
CD-RW discs including multi speed CD-RW discs, high-speed CD-RW  
discs and ultra-speed CD-RW discs can be recorded more than once.  
DVDs  
DVD-R, DVD+R, DVD-R (Dual Layer) and DVD+R (Double Layer) discs  
can be written only once. The recorded data cannot be erased or  
changed.  
DVD-RW, DVD+RW and DVD-RAM discs can be recorded more than  
once.  
Some types and formats of DVD-R (Dual Layer) and DVD+R (Double  
Layer) discs may be unreadable.  
BDs  
BD-R, BD-R(DL) discs can be written only once. The recorded data  
cannot be erased or changed.  
BD-RE, BD-RE(DL) discs can be recorded more than once.  
User’s Manual  
2-15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
The Grand Tour  
BD-Writer drive  
The full-size BD-Writer drive module lets you record data to writable  
CD/DVD/BD discs as well as run either 12 cm (4.72") or 8 cm (3.15") for  
Tray type CD/DVD/BDs without using an adaptor.  
The read speed is slower at the centre of a disc and faster at the outer  
edge.  
BD-ROM read  
DVD ROM read  
CD-ROM read  
BD-R write  
6 speed (maximum)  
8 speed (maximum)  
24 speed (maximum)  
6 speed (maximum)  
4 speed (maximum)  
2 speed (maximum)  
2 speed (maximum)  
8 speed (maximum)  
6 speed (maximum)  
8 speed (maximum)  
8 speed (maximum)  
4 speed (maximum)  
4 speed (maximum)  
5 speed (maximum)  
24 speed (maximum)  
16 speed (maximum, Ultra-speed media)  
BD-R(DL) write  
BD-RE write  
BD-RE(DL) write  
DVD-R write  
DVD-RW write  
DVD+R write  
DVD+RW write  
DVD-R DL write  
DVD+R DL write  
DVD-RAM write  
CD-R write  
CD-RW write  
BD-Combo drive  
The full-size BD-Combo drive module lets you record data to writable  
CD/DVD/BDs as well as run either 12 cm (4.72") or 8 cm (3.15") for Tray  
type CD/DVD/BDs without using an adaptor.  
The read speed is slower at the centre of a disc and faster at the outer  
edge.  
BD-ROM read  
DVD-ROM read  
CD-ROM read  
DVD-R write  
6 speed (maximum)  
8 speed (maximum)  
24 speed (maximum)  
8 speed (maximum)  
6 speed (maximum)  
8 speed (maximum)  
4 speed (maximum)  
4 speed (maximum)  
4 speed (maximum)  
5 speed (maximum)  
24 speed (maximum)  
16 speed (maximum, Ultra-speed media)  
DVD-RW write  
DVD+R write  
DVD+RW write  
DVD-R DL write  
DVD+R DL write  
DVD-RAM write  
CD-R write  
CD-RW write  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2-16  
The Grand Tour  
DVD Super Multi drive  
The full-size DVD Super Multi drive module allows you to record data to  
recordable CD's and DVD's as well as run 12cm(4.72") and 8cm(3.15")  
CD's and DVD's without using an adaptor.  
The speed is slower at the center of a disc and faster at the outer edge.  
DVD read  
8 speed (maximum)  
8 speed (maximum)  
6 speed (maximum)  
6 speed (maximum)  
8 speed (maximum)  
6 speed (maximum)  
8 speed (maximum)  
5 speed (maximum)  
24 speed (maximum)  
24 speed (maximum)  
24 speed (maximum,  
Ultra-speed media)  
DVD-R write  
DVD-R DL write  
DVD-RW write  
DVD+R write  
DVD+R DL write  
DVD+RW write  
DVD-RAM write  
CD read  
CD-R write  
CD-RW write  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2-17  
The Grand Tour  
AC adaptor  
The AC adaptor can automatically adjust to any voltage ranging from 90 to  
264 volts and to a frequency of either 47 or 63 hertz, enabling you to use  
this computer in almost any country/region. The adaptor converts AC  
power to DC power and reduces the voltage supplied to this computer.  
To recharge the battery, simply connect the AC adaptor to a power source  
and to the computer. Please refer to Chapter 6, Power and Power-up  
Modes for further information.  
Figure 2-9 The AC adaptor (2-pin plug)  
Figure 2-10 The AC adaptor (3-pin plug)  
Depending on the model in question, either a 2-pin or 3-pin  
adaptor/power lead will be bundled with the computer.  
Do not use a 3-pin to 2-pin conversion plug.  
The supplied power cord conforms to safety rules and regulations in  
the region the product is bought and should not be used outside of this  
region. In order to use the adaptor/computer in other regions, you  
should please buy a power cord that conforms to the safety rules and  
regulations in that particular region.  
Always use the TOSHIBA AC adaptor that was included with your  
computer, or use AC adaptors specified by TOSHIBA to avoid any risk of  
fire or other damage to the computer. Use of an incompatible AC adaptor  
could cause fire or damage to the computer possibly resulting in serious  
injury.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2-18  
   
Chapter 3  
Getting Started  
If the battery pack is not pre-installed in the computer that you  
purchased, please install the battery pack before you start using the  
computer.  
Please refer to Chapter 6-9, Replacing the battery pack for further  
information about installing the battery pack.  
All users should be sure to read the section Starting up for the first time.  
Be sure to read the enclosed Instruction Manual for Safety and Comfort  
for information on the safe and proper use of this computer. It is  
intended to help you be more comfortable and productive while using a  
notebook computer. By following the recommendations in it you may  
reduce your chance of developing a painful or disabling injury to your  
hand, arms, shoulders or neck.  
This chapter provides basic information to start using your computer. It  
covers the following topics:  
Connecting the AC adaptor  
Opening the display  
Turning on the power  
Starting up for the first time  
Turning off the power  
Restarting the computer  
System Recovery Options  
Creating Optical Recovery Discs  
Restoring the pre-installed software from the Recovery hard disk drive  
Restoring the pre-installed software from your created Recovery Discs  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3-1  
     
Getting Started  
Use an anti-virus software and update it regularly.  
Never format storage media without checking its content - formatting  
destroys all stored data.  
It is a good idea to periodically back up the internal hard disk drive or  
other main storage device to external media. General storage media is  
not durable or stable over long periods of time and under certain  
conditions may result in data loss.  
Before you install a device or application, save any data in memory to  
the hard disk drive or other storage media. Failure to do so may result  
in the loss of data.  
Connecting the AC adaptor  
Attach the AC adaptor when you need to charge the battery or you want to  
operate from AC power. It is also the fastest way to get started, because  
the battery pack will need to be charged before you can operate from  
battery power.  
The AC adaptor can be connected to any power source supplying from 90  
to 264 volts and 47 or 63 hertz. For details on using the AC adaptor to  
charge the battery pack, refer to Chapter 6, Power and Power-up Modes.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3-2  
   
Getting Started  
Always use the TOSHIBA AC adaptor that was included with your  
computer or use AC adaptors specified by TOSHIBA to avoid any risk  
of fire or other damage to the computer. Use of an incompatible AC  
adaptor could cause fire or damage to the computer possibly resulting  
in serious injury. TOSHIBA assumes no liability for any damage caused  
by use of an incompatible adaptor.  
Never plug the AC adaptor into a power source that does not  
correspond to both the voltage and the frequency specified on the  
regulatory label of the unit. Failure to do so could result in a fire or  
electric shock, possibly resulting in serious injury.  
Always use or purchase power cables that comply with the legal  
voltage and frequency specifications and requirements in the country of  
use. Failure to do so could result in a fire or electric shock, possibly  
resulting in serious injury.  
The supplied power cord conforms to safety rules and regulations in  
the region from which the product is purchased and should not be used  
outside this region. For use in other regions, please buy power cords  
that conform to safety rules and regulations in that particular region.  
Do not use a 3-pin to 2-pin conversion plug.  
When you connect the AC adaptor to the computer, always follow the  
steps in the exact order as described in the User’s Manual. Connecting  
the power cable to a live electrical outlet should be the last step  
otherwise the adaptor DC output plug could hold an electrical charge  
and cause an electrical shock or minor bodily injury when touched. As  
a general safety precaution, avoid touching any metal parts.  
Never place your computer or AC adaptor on a wooden surface,  
furniture, or any other surface that could be marred by exposure to heat  
since the computer base and AC adaptor's surface increase in  
temperature during normal use.  
Always place your computer or AC adaptor on a flat and hard surface  
that is resistant to heat damage.  
Refer to the enclosed Instruction Manual for Safety and Comfort for  
detailed precautions and handling instructions.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3-3  
Getting Started  
1. Connect the power cord to the AC adaptor.  
Figure 3-1 Connecting the power cord to the AC adaptor (2-pin plug)  
Figure 3-2 Connecting the power cord to the AC adaptor (3-pin plug)  
Either a 2-pin or 3-pin adaptor/cord will be included with the computer  
depending on the model.  
2. Connect the AC adaptor's DC output plug to the DC IN 19V jack on the  
right side of the computer.  
Figure 3-3 Connecting the adaptor to the computer  
3. Plug the power cord into a live wall outlet - the Battery and DC IN  
indicators on the front of the computer should glow.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3-4  
Getting Started  
Opening the display  
The display panel can be opened to a wide range of angles for optimal  
viewing.  
While holding down the palm rest with one hand so that the main body of  
the computer is not raised, slowly lift the display panel - this will allow the  
angle of the display panel to be adjusted to provide optimum clarity.  
Figure 3-4 Opening the display  
Use reasonable care when opening and closing the display panel. Opening  
it vigorously or slamming it shut could damage the computer.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3-5  
   
Getting Started  
When opening the panel, please be careful not to force it beyond the  
point where it moves easily.  
Be careful not to open the display panel too far as this could put stress  
on the display panel’s hinges and cause damage.  
Do not press or push on the display panel.  
Do not lift the computer by the display panel.  
Do not close the display panel with pens or any other objects left in  
between the display panel and the keyboard.  
When opening or closing the display panel, place one hand on the  
palm rest to hold the computer in place and use the other hand to  
slowly open or close the display panel (Do not use excessive force  
when opening or closing the display panel).  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3-6  
Getting Started  
Turning on the power  
This section describes how to turn on the power - the power indicator  
light will then indicate the status. Please refer to the Monitoring of power  
condition section in Chapter 6, Power and Power-up Modes for more  
information.  
After you turn on the power for the first time, do not turn it off until you  
have set up the operating system. Please refer to the section Starting  
up for the first time for more information.  
Volume cannot be adjusted during Windows Setup.  
1. Open the computer's display panel.  
2. Press the computer's power button.  
Figure 3-5 Turning on the power  
Starting up for the first time  
The Windows 7 Welcome Screen will be the first screen displayed when  
you turn on the power. Follow the on-screen instructions on each screen in  
order to properly install the operating system.  
When it is displayed, be sure to read the Software License Terms  
carefully.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3-7  
     
Getting Started  
Turning off the power  
The power can be turned off in one of three modes, either Shut Down  
Mode, Hibernation Mode or Sleep Mode.  
Shut Down Mode  
When you turn off the power in Shut Down Mode no data will be saved and  
the computer will boot to the operating system's main screen the next time  
it is turned on.  
1. If you have entered data, either save it to the hard disk drive or to other  
storage media.  
2. Make sure all disk/disc activity has stopped before removing the  
CD/DVD/BD or floppy diskette.  
Make sure the Hard Disk Drive indicator is off. If you turn off the power  
while a disk (disc) is being accessed, you may lose data or damage the  
disk.  
Never turn off the power while an application is running. Doing so could  
cause loss of data.  
Never turn off the power, disconnect an external storage device or  
remove storage media during data read/write. Doing so can cause data  
loss.  
3. Click Start.  
4. Click Shut down button (  
).  
5. Turn off any peripheral devices connected to your computer.  
Do not turn the computer or peripheral devices back on immediately - wait  
a short period to avoid any potential damage.  
Hibernation Mode  
The Hibernation Mode feature saves the contents of memory to the hard  
disk drive when the computer is turned off so that, the next time it is turned  
on, the previous state is restored. Please note that the Hibernation Mode  
feature does not save the status of any peripheral devices connected to the  
computer.  
Save your data. While entering Hibernation Mode, the computer saves  
the contents of memory to the hard disk drive. However, for safety  
sake, it is best to save your data manually.  
Data will be lost if you remove the battery or disconnect the AC adaptor  
before the save is completed. Wait for the Hard Disk Drive indicator  
light to go out.  
Do not install or remove a memory module while the computer is in  
Hibernation Mode. Data will be lost.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3-8  
         
Getting Started  
Benefits of Hibernation Mode  
The Hibernation Mode feature provides the following benefits:  
Saves data to the hard disk drive when the computer automatically  
shuts down because of a low battery condition.  
You can return to your previous working environment immediately when  
you turn on the computer.  
Saves power by shutting down the system when the computer receives  
no input or hardware access for the time period set by the System  
Hibernate feature.  
Allows the use of the panel power off feature.  
Starting Hibernation Mode  
You can also enable Hibernation Mode by pressing FN + F4 - please refer  
to Chapter 5, The Keyboard, for further details.  
To enter Hibernation Mode, follow the steps below.  
1. Click Start.  
2. Click the arrow button (  
) in the power management button  
(
) and select Hibernate from the menu.  
Automatic Hibernation Mode  
The computer can be configured to enter Hibernation Mode automatically  
when you press the power button or close the lid. In order to define these  
settings, you can follow the steps as described below:  
1. Click Start and click the Control Panel.  
2. Click System and Security and click Power Options.  
3. Click Choose what the power button does or Choose what closing  
the lid does.  
4. Enable the desired Hibernation Mode settings for When I press the  
power button and When I close the lid.  
5. Click the Save changes button.  
Data save in Hibernation Mode  
When you turn off the power in Hibernation Mode, the computer will take a  
moment to save the current data in memory to the hard disk drive. During  
this time, the Hard Disk Drive indicator will glow.  
After you turn off the computer, and the content of memory has been saved  
to the hard disk drive, turn off the power to any peripheral devices.  
Do not turn the computer or devices back on immediately. Wait a moment  
to let all capacitors fully discharge.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3-9  
Getting Started  
Sleep Mode  
If you have to interrupt your work, you are able to turn off the power without  
exiting from your software by placing the computer into Sleep Mode. In this  
mode data is maintained in the computer's main memory so that when you  
turn on the power again, you can continue working right where you left off.  
When you have to turn off your computer aboard an aircraft or in places  
where electronic devices are regulated or controlled, always completely  
shut down the computer. This includes turning off any devices, and  
canceling settings that reactivate the computer automatically, such as a  
timer recording function. Failure to completely shut down the computer in  
this way could allow the operating system to reactivate and run pre-  
programmed tasks or preserve unsaved data, which could interfere with  
aviation or other systems, possibly causing serious injury.  
Before entering Sleep Mode, be sure to save your data.  
Do not install or remove a memory module while the computer is in  
Sleep Mode. The computer or the memory module could be damaged.  
Do not remove the battery pack while the computer is in Sleep Mode  
(unless the computer is connected to an AC power source). Data in  
memory could be lost.  
When the AC adaptor is connected, the computer will go into Sleep Mode  
according to the settings in the Power Options (to access it, Start →  
Control Panel System and Security Power Options).  
To restore the operation of the computer from Sleep Mode, press and  
hold the power button or any key on the keyboard for a short amount of  
time. Please note that keyboard keys can only be used if the Wake-up  
on Keyboard option is enabled within the HW Setup utility.  
If the computer enters Sleep Mode while a network application is  
active, the application might not be restored when the computer is next  
turned on and the system returns from Sleep Mode.  
To prevent the computer from automatically entering Sleep Mode,  
disable Sleep Mode within the Power Options (to access it, Start →  
Control Panel System and Security Power Options).  
To use the Hybrid Sleep function, configure it in the Power Options.  
Benefits of Sleep Mode  
The Sleep Mode feature provides the following benefits:  
Restores the previous working environment more rapidly than does the  
Hibernation Mode feature.  
Saves power by shutting down the system when the computer receives  
no input or hardware access for the time period set by the System  
Sleep Mode feature.  
Allows the use of the panel power off feature.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3-10  
   
Getting Started  
Executing Sleep Mode  
You can also enable Sleep Mode by pressing FN + F3 - please refer to  
Chapter 5, The Keyboard, for further details.  
You can enter Sleep Mode in one of four ways:  
Click Start then click the arrow button (  
) in the power management  
button ( ) and select Sleep from the menu.  
Close the display panel. Please note that this feature must be enabled  
within the Power Options (to access it, click Start Control Panel →  
System and Security Power Options).  
Press the power button. Please note that this feature must be enabled  
within the Power Options (to access it, click Start Control Panel →  
System and Security Power Options).  
When you turn the power back on, you can continue where you left when  
you shut down the computer.  
When the computer is in Sleep Mode, the Power indicator will blink  
amber.  
If you are operating the computer on battery power, Sleep Mode will  
consume more power while the computer is off. You can lengthen the  
overall operating time by turning it off into Hibernation Mode.  
Sleep Mode limitations  
Sleep Mode will not function under the following conditions:  
Power is turned back on immediately after shutting down.  
Memory circuits are exposed to static electricity or electrical noise.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3-11  
Getting Started  
Restarting the computer  
Certain conditions require that you reset the computer, for example if:  
You change certain computer settings.  
An error occurs and the computer does not respond to your keyboard  
commands.  
If you need to restart the computer, there are three ways this can be  
achieved:  
Click Start then click the arrow button (  
) in the power management  
buttons ( ) and select Restart from the menu.  
Press CTRL, ALT and DEL simultaneously (once) to display the menu  
window, then select Restart from the Shut down options.  
Press the power button and hold it down for four seconds. Once the  
computer has turned itself off, wait between ten and fifteen seconds  
before turning the power on again by pressing the power button.  
System Recovery Options  
A hidden partition is allocated on the hard disk drive for the System  
Recovery Options.  
This partition stores files which can be used to repair the system in the  
event of a problem.  
The System Recovery Options feature will be unusable if this partition is  
deleted.  
System Recovery Options  
The System Recovery Options feature is installed on the hard disk when  
shipped from the factory. The System Recovery Options menu includes  
tools to repair startup problems, run diagnostics or restore the system.  
See the Windows Help and Support content for more information about  
Startup Repair.  
The System Recovery Options can also be run manually to repair  
problems.  
The procedure is as follows. Follow the instructions shown on the  
on-screen menu.  
1. Turn off the computer.  
2. While holding the F8 key, turn on the computer.  
3. The Advanced Boot Options menu will be displayed.  
Use the arrow keys to select Repair Your Computer and press  
ENTER.  
4. Follow the on-screen instructions.  
The Windows 7 CompletePC Backup feature can be used on Windows® 7  
Professional and Windows® 7 Ultimate.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3-12  
     
Getting Started  
Creating Optical Recovery Discs  
This section describes how to create Recovery Discs.  
Be sure to connect the AC adaptor when you create Recovery Discs.  
Be sure to close all other software programs except the TOSHIBA  
Recovery Media Creator.  
Do not run software such as screen savers which can put a heavy load  
on the CPU.  
Operate the computer at full power.  
Do not use power-saving features.  
Do not write to the disc when the anti-virus software is running. Wait for  
it to finish, then disable virus detection programs including any software  
that checks files automatically in the background.  
Do not use utilities, including those intended to enhance hard disk drive  
access speed. They may cause unstable operation and damage data.  
Do not shut down/log off or Sleep/Hibernate while writing or rewriting  
the disc.  
Set the computer on a level surface and avoid places subjected to  
vibrations such as airplanes, trains, or cars.  
Do not use on unstable tables or other any other unstable surfaces.  
A recovery image of the software on your computer is stored on the hard  
disk drive, and can be copied to DVD media by using the following steps:  
1. Select either blank DVD media.  
2. The application will allow you to choose from a variety of different media  
onto which the recovery image can be copied including DVD-R, DVD-R  
DL, DVD-RW, DVD+R, DVD+R DL and DVD+RW.  
Please note that some of the above media may not be compatible with the  
optical disc drive installed into your computer. You should therefore verify  
the optical disc drive supports the blank media you have chosen before  
proceeding.  
3. Turn on your computer and allow it to load the Windows 7 operating  
system from the hard disk drive as normal.  
4. Insert the first blank media into the optical disc drive tray.  
5. Double click the TOSHIBA Recovery Media Creator icon on the  
Windows 7 desktop, or select the application from Start Menu.  
6. After TOSHIBA Recovery Media Creator starts, select the type of media  
and the title you wish to copy, and then click the Create button.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3-13  
Getting Started  
Restoring the pre-installed software from the Recovery hard disk  
drive  
A portion of the total hard disk drive space is configured as a hidden  
recovery partition. This partition stores files which can be used to restore  
pre-installed software in the event of a problem.  
If you subsequently set up your hard disk drive again, do not change,  
delete or add partitions in a manner other than specified in the manual,  
otherwise you may find that space for the required software is not available.  
In addition, if you use a third-party partitioning program to reconfigure the  
partitions on your hard disk drive, you may find that it becomes impossible  
to setup your computer.  
When the sound mute feature has been activated by pressing the Mute  
panel (Fn+ESC), be sure to disable this to allow sounds to be heard before  
starting the restore process. Please refer to Chapter 5, The Keyboard, for  
further details.  
You can not use System Recovery Options if restoring the pre-installed  
software without System Recovery Options.  
When you reinstall the Windows operating system, the hard disk will be  
reformatted and all data will be lost.  
1. Turn off your computer.  
2. While holding down 0 (zero) key on the keyboard, turn on your  
computer.  
3. A menu will be displayed from which you should follow the on-screen  
instructions.  
User’s Manual  
3-14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Restoring the pre-installed software from your created Recovery  
Discs  
If the pre-installed files are damaged, you are able to either use the  
Recovery Discs you have created or the hard disk drive recovery process  
to restore the computer to the state it was in when you originally received it.  
To perform this restoration, follow the steps below:  
When the sound mute feature has been activated by pressing the FN +  
ESC key, be sure to disable this to allow sounds to be heard before starting  
the restore process. Please refer to Chapter 5,The Keyboard, for further  
details.  
You can not use System Recovery Options if restoring the pre-installed  
software without System Recovery Options.  
When you reinstall the Windows operating system, the hard disk will be  
reformatted and all data will be lost.  
1. Load the Recovery Discs into the optical disc drive and turn off the  
computer's power.  
2. While holding down F12 key on the keyboard, turn on your computer -  
when TOSHIBA Leading Innovation>>>appears, release the F12  
key.  
3. Use the up and down cursor keys to select the CD-ROM icon from the  
menu. Please refer to the Boot Priority section in Chapter 7, HW Setup  
and Passwords for further information.  
4. A menu will be displayed from which you should follow the on-screen  
instructions.  
When drivers/utilities are installed, you can setup the respective  
drivers/utilities from following place.  
To open the setup files, Click Start All Programs TOSHIBA →  
Applications and Drivers.  
User’s Manual  
3-15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Chapter 4  
Operating Basics  
This chapter describes the basic operations of your computer and  
highlights the precautions that should be taken when using it.  
Using the Touch Pad  
To use the Touch Pad, simply touch and move your fingertip across it in the  
direction you want the on-screen pointer to go.  
1
2
1. Touch Pad  
2. Touch Pad buttons  
Figure 4-1 Touch Pad and Touch Pad control buttons  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4-1  
           
Operating Basics  
Touch Pad Gesture  
There are four convenient gestures that make users operate the system  
easier and faster.  
Circular Motion  
You can scroll vertically and horizontally. To enable these features, select  
the Enable vertical scrolling and Enable horizontal scrolling check  
boxes.  
Click on the window or item you wish to scroll and slide your finger upwards  
or downwards along the right edge of the TouchPad to scroll vertically.  
Slide your finger to the left or right along the lower edge of the TouchPad to  
scroll horizontally.  
If scrolling does not respond, ensure that the appropriate check box is  
selected and that the window or item on which you have clicked is  
scrollable. If you still have problems, check your Scrolling Region settings.  
Pinch Zoom (Pinch)  
The Pinch Zoom gesture delivers zooming functionality in many  
applications. You can use the Pinch Zoom gesture to perform the same  
functions that a scroll wheel performs on standard Windows applications  
that support CTRL-SCROLL WHEEL zoom functionality.  
To enable this feature, select the Enable Pinch Zoom check box.  
To use a Pinch Zoom gesture:  
1. Place two fingers down on the TouchPad surface.  
2. Slide the fingers further apart to zoom in or slide the fingers closer  
together to zoom out. For the best zooming experience, use the tips of  
your fingers.  
Rotating (ChiralRotate)  
The Rotating features provide convenient gestures for rotating photos and  
other objects.  
Momentum  
The Momentum feature delivers smooth, fast, trackball-like mouse  
movement. One quick flick of the finger on the TouchPad surface can move  
the cursor across the entire computer screen. Momentum reduces the  
repetitive motion and fatigue associated with moving the cursor long  
distances, while providing a smooth and natural feel similar to using a  
trackball. Momentum is ideal for Real Time Strategy (RTS) games, First  
Person Shooter (FPS) games, and Role Playing Games (RPG).  
The two buttons below the Touch Pad are used like the buttons on a  
standard mouse - press the left button to select a menu item or to  
manipulate text or graphics designated by the pointer, and press the right  
button to display a menu or other function depending on the software you  
are using.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4-2  
 
Operating Basics  
You can also tap the Touch Pad to perform functions similar to those of the  
left button on a standard mouse.  
Click: Tap once  
Double-click: Tap twice  
Drag and drop: Tap to select the item(s) you want to move, leave your  
finger on the Touch Pad after the second tap and then move the item(s)  
to their new destination.  
Using optical disk drives  
The full-size drive provides high-performance execution of CD/DVD/BD-  
based programs. You can run either 12 cm (4.72") or 8 cm (3.15")  
CD/DVD/BDs without an adaptor. A Serial ATA interface controller is used  
for CD/DVD/BD operation. When the computer is accessing a CD/DVD/BD,  
an indicator on the drive glows.  
Use the DVD playback application to view DVD-Video discs.  
Loading discs  
To load CD/DVD/BD's, follow the steps as listed below and refer to figures  
4-4 to 4-6.  
1. When the computer's power is on, press the eject button to open the  
disc tray slightly.  
a
1. Eject button  
Figure 4-2 Pressing the eject button  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4-3  
 
Operating Basics  
2. Grasp the disc tray gently and pull until it is fully opened.  
Figure 4-3 Pulling the disc tray open  
3. Lay the CD/DVD/BD, label side up, in the disc tray.  
Figure 4-4 Inserting a CD/DVD/BD  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4-4  
Operating Basics  
When the disc tray is fully opened, the edge of the computer will extend  
slightly over the area where you insert the media. Therefore, when loading  
a CD, DVD or BD, you will need to turn it slightly at an angle when you  
place it in the disc tray. After loading the CD/DVD/BD you should ensure  
that it is properly positioned over the central spindle and that it lies flat  
within the tray.  
Do not touch either the laser lens or the area immediately around it -  
doing so could cause misalignment and may damage the drive.  
Make sure that no foreign objects are inserted into or otherwise enter  
the drive.  
Check the disc tray, especially the area behind the front edge, to  
ensure that there are no foreign objects or material present before  
closing the drive.  
4. Press the center of the CD/DVD/BD gently until you feel it click into  
place on the center spindle. The disc should be slightly below the top of  
the spindle and flush with the spindle base.  
5. Press the center of the disc tray in order to close it - the tray will click  
into place when it is locked.  
If the CD/DVD/BD is not seated properly when the disc tray is closed, you  
may find that the media itself might become damaged, and/or the disc tray  
might not open fully when you next press the eject button.  
Removing discs  
Do not press the eject button while the computer is accessing the media in  
the drive, instead wait for the indicator to go out before you open the disc  
tray. In addition, if the CD/DVD/BD media is spinning when you open the  
tray, wait for it to fully stop before you remove it.  
To remove a CD/DVD/BD, follow the steps as listed below.  
1. When the computer's power is on, press the eject button to open the  
disc tray slightly and then gently pull it out of the system until it is fully  
opened.  
After the disc tray has opened slightly, you should wait for a moment to  
ensure the CD/DVD/BD media has stopped spinning before you fully open  
the tray.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4-5  
Operating Basics  
2. The CD/DVD/BD media will extend slightly over the sides of the disc  
tray in order that you can hold it. Grasp it carefully by its edges and lift it  
vertically off of the central spindle and out of the tray.  
Figure 4-5 Removing a CD/DVD/BD  
3. Press the center of the disc tray in order to close it - the tray will click  
into place when it is locked.  
How to remove a CD/DVD/BD when the disc tray will not open  
Pressing the eject button will not open the disc tray when the computer is  
turned off although, in these circumstances, you can open the tray by  
inserting a slender object such as a straightened paper clip about 15mm  
into the eject hole just to the right of the drive's eject button.  
a
1. Eject hole  
Figure 4-6 Manual release with the eject hole  
You must ensure that you turn off the power before you use the eject hole.  
If the CD/DVD/BD media is spinning when you open the disc tray, it may fly  
off of the spindle and cause injury.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4-6  
Operating Basics  
Function buttons  
This section describes the Function buttons.  
Four buttons located next to the Power button are provided with some  
models.  
Figure 4-7 Function buttons  
Icon  
Function button  
DVD/BD  
*CD/None  
Play/Pause  
Play/Pause  
Play/Pause  
Previous  
Next  
Previous chapter  
Next chapter  
Mute  
Previous track  
Next track  
Mute  
Mute  
Writing CD/DVD/BD on DVD Super Multi drives or BD Writer  
drives or BD Combo drives  
The optical drive installed on this computer cannot write multiple sessions  
on DVD-R Dual Layer disc sessions. Once a disc has been written to once,  
it will be finalized. Once finalized, no further writing to the disc will be  
possible regardless of what portion of the total disc capacity was used.  
You can use the DVD SuperMulti drive or BD Writer drives or BD Combo  
drives to write data to either CD-R, CD-RW, DVD-R, DVD-R (Dual Layer),  
DVD-RW, DVD+R, DVD+R (Double Layer), DVD+RW, DVD-RAM, DVD-R  
(Dual Layer) or BD-R/BD-RE discs.  
TOSHIBA Disc Creator and Corel DVD MovieFactory are provided as  
writing software with this computer.  
Corel DVD MovieFactory can be used to write files in video format.  
TOSHIBA Disc Creator can be used to write data.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4-7  
     
Operating Basics  
Please refer to the section Writable discs, Chapter 2 for details about  
the types of writable CD, DVD and BD discs that can be supported by  
this computer.  
Do not turn off the power to the optical disc drive while the computer is  
accessing it as this may cause you to lose data.  
CD-R/RW media cannot be accessed using the Create CD/DVD/BD  
option in Media Center.  
To write data to CD-R/-RW media, use the TOSHIBA Disc Creator  
feature that is installed on your computer.  
When writing information to media using an optical drive, you should  
always ensure that you connect the AC adaptor to a live power socket. It is  
possible that, if data is written while powered by the battery pack, the write  
process may sometimes fail due to low battery power - in these instances  
data loss may occur.  
Important message  
Before you write or rewrite to any of the media supported by the DVD  
Super Multi drive or BD drive, please read and follow all of the setup and  
operating instructions in this section. If you fail to do so, you may find that  
the DVD Super Multi drive or BD drive may not function properly, and you  
may fail to write or rewrite information successfully. This may cause you to  
either lose data or incur other damage to the drive or media.  
Before writing or rewriting  
Based on TOSHIBA's limited compatibility testing, we suggest the  
following manufacturers of CD-R, CD-RW, DVD-R, DVD-R (Dual  
Layer), DVD-RW, DVD+R, DVD+R (Double Layer), DVD+RW or DVD-  
RAM media, however, it must be noted that disc quality can affect write  
or rewrite success rates. Please also be aware that in no event does  
TOSHIBA guarantee the operation, quality or performance of any disc.  
CD-R:  
TAIYO YUDEN CO., Ltd.  
MITSUBISHI KAGAKU MEDIA CO., LTD.  
Hitachi Maxell,Ltd.  
CD-RW: (Multi-Speed and High-Speed)  
MITSUBISHI KAGAKU MEDIA CO., LTD.  
CD-RW: (Ultra-Speed)  
MITSUBISHI KAGAKU MEDIA CO., LTD.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4-8  
Operating Basics  
DVD-R:  
DVD Specifications for Recordable Disc for General Version 2.0  
TAIYO YUDEN Co.,Ltd. (for 8x and 16x speed media)  
MITSUBISHI KAGAKU MEDIA CO., LTD. (for 4x, 8x and 16x speed  
media)  
Hitachi Maxell,Ltd. (for 8x and 16x speed media)  
DVD-R (Dual Layer):  
MITSUBISHI KAGAKU MEDIA CO., LTD. (for 4x and 8x speed media)  
DVD-R for Labelflash:  
FUJIFILM CORPORATION (for 16x speed media)  
DVD+R:  
MITSUBISHI KAGAKU MEDIA CO., LTD. (for 8x and 16x speed  
media)  
TAIYO YUDEN CO., Ltd. (for 8x and 16x speed media)  
DVD+R (Double Layer):  
MITSUBISHI KAGAKU MEDIA CO., LTD. (for 2.4x and 8x speed  
media)  
DVD+R for Labelflash:  
FUJIFILM CORPORATION (for 16x speed media)  
DVD-RW:  
DVD Specifications for Recordable Disc for Version 1.1 or version 1.2  
Victor Company of Japan, Ltd. (JVC) (for 2x, 4x and 6x speed media)  
MITSUBISHI KAGAKU MEDIA CO., LTD. (for 2x, 4x and 6x speed  
media)  
DVD+RW:  
MITSUBISHI KAGAKU MEDIA CO., LTD. (for 2.4x, 4x and 8x speed  
media)  
DVD-RAM:  
DVD Specifications for DVD-RAM Disc for Version 2.0, Version 2.1  
or Version 2.2  
Matsushita Electric Industrial Co.,Ltd. (for 3x and 5x speed media)  
Hitachi Maxell,Ltd. (for 3x and 5x speed media)  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4-9  
Operating Basics  
BD-Combo drive  
CD-R:  
TAIYO YUDEN CO., Ltd.  
MITSUBISHI KAGAKU MEDIA CO., LTD.  
Hitachi Maxell,Ltd.  
CD-RW: (Multi-Speed and High-Speed)  
MITSUBISHI KAGAKU MEDIA CO., LTD.  
CD-RW: (Ultra-Speed)  
MITSUBISHI KAGAKU MEDIA CO., LTD.  
DVD-R: (DVD Specifications for Recordable Disc for General  
Version 2.0)  
TAIYO YUDEN Co.,Ltd. (for 8x and 16x speed media)  
MITSUBISHI KAGAKU MEDIA CO., LTD. (for 4x, 8x and 16x speed  
media)  
Hitachi Maxell,Ltd. (for 8x and 16x speed media)  
DVD-R for Labelflash:  
FUJIFILM CORPORATION (for 16x speed media)  
DVD+R:  
MITSUBISHI KAGAKU MEDIA CO., LTD. (for 8x and 16x speed  
media)  
DVD+R for Labelflash:  
FUJIFILM CORPORATION (for 16x speed media)  
DVD-RW:  
DVD Specifications for Recordable Disc for Version 1.1 or version 1.2  
Victor Company of Japan, Ltd. (JVC) (for 2x, 4x and 6x speed media)  
MITSUBISHI KAGAKU MEDIA CO., LTD. (for 2x, 4x and 6x speed  
media)  
DVD-RAM: (DVD Specifications for DVD-RAM Disc for Version 2.0,  
Version 2.1 or Version 2.2)  
Panasonic CO., LTD. (for 3x and 5x speed media)  
Hitachi Maxell,Ltd. (for 3x and 5x speed media)  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4-10  
Operating Basics  
BD Writer drive  
CD-R:  
TAIYO YUDEN CO., Ltd.  
MITSUBISHI KAGAKU MEDIA CO., LTD.  
Hitachi Maxell,Ltd.  
CD-RW: (Multi-Speed and High-Speed)  
MITSUBISHI KAGAKU MEDIA CO., LTD.  
CD-RW: (Ultra-Speed)  
MITSUBISHI KAGAKU MEDIA CO., LTD.  
DVD-R: (DVD Specifications for Recordable Disc for General  
Version 2.0)  
TAIYO YUDEN Co.,Ltd. (for 8x and 16x speed media)  
MITSUBISHI KAGAKU MEDIA CO., LTD. (for 4x, 8x and 16x speed  
media)  
DVD-R for Labelflash:  
FUJIFILM CORPORATION (for 16x speed media)  
DVD+R:  
MITSUBISHI KAGAKU MEDIA CO., LTD. (for 8x and 16x speed  
media)  
DVD+R for Labelflash:  
FUJIFILM CORPORATION (for 16x speed media)  
DVD-RW:  
DVD Specifications for Recordable Disc for Version 1.1 or version 1.2  
Victor Company of Japan, Ltd. (JVC) (for 2x, 4x and 6x speed media)  
MITSUBISHI KAGAKU MEDIA CO., LTD. (for 2x, 4x and 6x speed  
media)  
DVD-RAM: (DVD Specifications for DVD-RAM Disc for Version 2.0,  
Version 2.1 or Version 2.2)  
Panasonic CO., LTD. (for 3x and 5x speed media)  
Hitachi Maxell,Ltd. (for 3x and 5x speed media)  
BD-R:  
Panasonic CO., LTD.  
BD-R(DL):  
Panasonic CO., LTD.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4-11  
Operating Basics  
BD-RE:  
Panasonic CO., LTD.  
BD-RE(DL):  
Panasonic CO., LTD.  
DVD Super Multi drive cannot use discs that allow writing faster than  
16x speed (DVD-R and DVD+R media), 8x speed (DVD-R (Dual  
Layer), DVD+RW and DVD+R (Double Layer) media), 6x speed (DVD-  
RW media), 5x speed (DVD-RAM media).  
Some types and formats of DVD-R (Dual Layer) and DVD+R (Double  
Layer) discs may be unreadable.  
2.6GB and 5.2GB DVD-RAM media cannot be read from or written to.  
DISC created in DVD-R (Dual Layer) format4 (Layer Jump Recording)  
cannot be read.  
If the disc is poor in quality, or is dirty or damaged, writing or rewriting  
errors may be noted - ensure that you check all discs for dirt or damage  
before you use them.  
The actual number of rewrites to CD-RW, DVD-RW, DVD+RW or DVD-  
RAM media will be affected by the quality of the disc itself and the way  
in which it is used.  
There are two types of DVD-R media available, authoring discs and  
general use discs. Do not attempt to use authoring discs as only  
general use discs can be written to by a computer drive.  
You can use both DVD-RAM discs that can be removed from a cartridge  
and DVD-RAM discs designed without a cartridge.  
You may find that other computer DVD-ROM drives or other DVD  
players may not be able to read DVD-R, DVD-R (Dual Layer), DVD-RW,  
DVD+R, DVD+R (Double Layer) or DVD+RW discs.  
Data written to a CD-R, DVD-R, DVD-R (Dual Layer), DVD+R or  
DVD+R (Double Layer) discs cannot be deleted either in whole or in  
part.  
Data deleted/erased from a CD-RW, DVD-RW, DVD+RW or DVD-RAM  
disc cannot be recovered. You must check the content of the disc  
carefully before you delete it, making sure that if multiple drives that can  
write data to discs are connected, you do not delete data from the  
wrong one.  
In writing to DVD-R, DVD-R (Dual Layer), DVD-RW, DVD+R, DVD+R  
(Double Layer), DVD+RW or DVD-RAM media, some space is required  
for file management, so you may not be able to write to the full capacity  
of the disc.  
Since the disc is based on the DVD standard, it might be filled with  
dummy data if the written data is less than about 1GB. Therefore, in  
these circumstance, even if you write only a small amount of data, it  
might take additional time to fill in the dummy data.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4-12  
Operating Basics  
When multiple drives that can write data to discs are connected, be  
sure that you do not write to or delete data from the wrong drive.  
Be sure to connect the AC adaptor to the computer before you write or  
rewrite any information.  
Before you enter either Sleep Mode or Hibernation Mode, take care to  
ensure that any DVD-RAM writing has been completed. In this instance,  
writing is finished if you can eject the DVD-RAM media.  
Be sure to close all other software programs except for the writing  
software itself.  
Do not run software such as a screen saver which can put a heavy load  
on the processor.  
Operate the computer at its full power settings - do not use any power-  
saving features.  
Do not write information while virus checking software is running,  
instead wait for it to finish, then disable the virus protection applications,  
including any software that checks files automatically in the  
background.  
Do not use any hard disk utilities, including those that are intended to  
enhance hard disk drive access speeds, as they may cause unstable  
operation and damage data.  
CD-RW (Ultra Speed +) media should not be used as data may be lost  
or damaged.  
You should always write from the computer's hard disk drive onto the  
CD/DVD/BD - do not try to write from shared devices such as a server  
or any other network device.  
Writing with software other than TOSHIBA Disc Creator has not been  
confirmed, therefore operation with other software applications cannot  
be guaranteed.  
When writing or rewriting  
Please observe the following points while you write or rewrite data to CD-R,  
CD-RW, DVD-R, DVD-R (Dual Layer), DVD-RW, DVD+R, DVD+R (Double  
Layer), DVD+RW DVD RAM or BD-R/BD-RE media:  
Always copy data from the hard disk drive to the optical media - do not  
use the cut-and-paste function as the original data will be lost if there is  
a write error.  
Do not perform any of the following actions:  
Change users in the Windows® 7 operating system.  
Operate the computer for any other function, including such tasks as  
using a mouse or Touch Pad, or closing/opening the display panel.  
Start a communication application such as a modem.  
Apply impact or vibration to the computer.  
Install, remove or connect external devices, including such items as  
a SD/SDHC memory card, miniSD/microSD Card, PC Card,  
Memory Stick/Memory Stick PRO, MultiMediaCard, USB device,  
external monitor, or an optical digital device or BD drive.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4-13  
Operating Basics  
Use the audio/video control button to reproduce music or voice.  
Open the optical disc drive or BD drive.  
Do not use shut down, log off, Sleep Mode or Hibernation Mode  
functions while writing or rewriting.  
Make sure that the write/rewrite operation is completed before going  
into either Sleep Mode or Hibernation Mode (writing is completed if you  
can remove an optical media on the DVD Super Multi drive or BD drive).  
If the media is of poor quality, or is dirty or damaged, writing or rewriting  
errors may occur.  
Set the computer on a level surface and avoid places subject to  
vibration such as airplanes, trains or cars. In addition, do not use the  
computer on an unstable surface such as a stand.  
Keep mobile phones and other wireless communication devices away  
from the computer.  
Disclaimer  
TOSHIBA does not bear responsibility for the following:  
Damage to any CD-R, CD-RW, DVD-R, DVD-R (Dual Layer), DVD-RW,  
DVD+R, DVD+R (Double Layer), DVD+RW or DVD-RAM disc that may  
be caused by writing or rewriting with this product.  
Any change or loss of the recorded contents of CD-R, CD-RW, DVD-R,  
DVD-R (Dual Layer), DVD-RW, DVD+R, DVD+R (Double Layer),  
DVD+RW or DVD-RAM media that may be caused by writing or  
rewriting with this product, or for any business profit loss or business  
interruption that may be caused by the change or loss of the recorded  
contents.  
Damage that may be caused by using third party equipment or  
software.  
Given the technological limitations of current optical disc writing drives, you  
may experience unexpected writing or rewriting errors due to disc quality or  
problems with hardware devices. In view of this, it is good practice to make  
two or more copies of important data, in case of any undesired change or  
loss of the recorded contents.  
TOSHIBA Disc Creator  
Please be aware of the following limitations when you use the TOSHIBA  
Disc Creator:  
DVD Video cannot be created using TOSHIBA Disc Creator.  
DVD Audio cannot be created using TOSHIBA Disc Creator.  
You cannot use TOSHIBA Disc Creator's 'Audio CD for Car or Home  
CD Player' function to record music to DVD-R, DVD-R (Dual Layer),  
DVD-RW, DVD+R, DVD+R (Double Layer) or DVD+RW media.  
Do not use the 'Disc Backup' function of TOSHIBA Disc Creator in order  
to copy DVD Video or DVD-ROM material that has copyright protection.  
DVD-RAM discs cannot be backed up using the 'Disc Backup' function  
of TOSHIBA Disc Creator.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4-14  
 
Operating Basics  
You cannot back up CD-ROM, CD-R or CD-RW media to DVD-R, DVD-  
R (Dual Layer) or DVD-RW media using the 'Disc Backup' function of  
TOSHIBA Disc Creator.  
You cannot back up CD-ROM, CD-R or CD-RW media to DVD+R,  
DVD+R (Double Layer) or DVD+RW media using the 'Disc Backup'  
function of TOSHIBA Disc Creator.  
You cannot back up DVD-ROM, DVD Video, DVD-R, DVD-R (Dual  
Layer), DVD-RW, DVD+R, DVD+R (Double Layer) or DVD+RW to CD-  
R or CD-RW media using the 'Disc Backup' function of TOSHIBA Disc  
Creator.  
TOSHIBA Disc Creator cannot record in packet format.  
You might not be able to use the 'Disc Backup' function of TOSHIBA  
Disc Creator to back up a DVD-R, DVD-R (Dual Layer), DVD-RW,  
DVD+R, DVD+R (Double Layer) or DVD+RW disc that was made with  
other software on a different optical media recorder.  
If you add data to a DVD-R, DVD-R (Dual Layer), DVD+R or DVD+R  
(Double Layer) disc that you have already recorded to, you might not be  
able to read the added data under some circumstances. For example, it  
cannot be read under 16-bit operating systems, such as Windows 98SE  
and Windows Me, while in Windows NT4 you will need Service Pack 6  
or later, and in Windows 2000, you will need Service Pack 2. In addition  
to this, some DVD-ROM and DVD-ROM / CD-R/RW drives cannot read  
this added data regardless of the operating system.  
TOSHIBA Disc Creator does not support recording to DVD-RAM discs -  
to achieve this you should use Windows Explorer or another similar  
utility.  
When you back up a DVD disc, be sure that the source drive supports  
recording to DVD-R, DVD-R (Dual Layer), DVD-RW, DVD+R, DVD+R  
(Double Layer) or DVD+RW media - if this is not the case then the  
source disc might not be backed up correctly.  
When you back up a DVD-R, DVD-R (Dual Layer), DVD-RW, DVD+R,  
DVD+R (Double Layer) or DVD+RW disc, be sure to use the same type  
of disc.  
You cannot partially delete any data written to a CD-RW, DVD-RW or  
DVD+RW disc.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4-15  
Operating Basics  
Data Verification  
To verify that data has been written or rewritten correctly to a data  
CD/DVD/BD you should follow the steps below before you begin the  
write/rewrite process:  
1. Select Settings for Each Mode Data Disc in the Setting menu.  
2. Display the setting dialog box by one of the following two steps:  
Click the Recording settings button (  
) for writing on the main  
toolbar in the "Data CD/DVD" mode.  
Select Settings for Each Mode Data CD/DVD in the Settings  
menu.  
3. Mark the Verify written data check box.  
4. Select File Open or Full Compare mode.  
5. Click the OK button.  
How to learn more about TOSHIBA Disc Creator  
Please refer to the Help files for additional TOSHIBA Disc Creator  
information.  
Opening the TOSHIBA Disc Creator Manual  
Start All Programs TOSHIBA CD&DVD Applications Disc  
Creator Help  
How to make a Labelflash DVD  
Simplified steps for making a Labelflash DVD:  
1. Insert a Labelflash disc in optical disc drive.  
Set PRINTING SIDE for underside.  
2. Click Start All Programs DVD MovieFactory for TOSHIBA →  
DVD MovieFactory Lancher to launch DVD MovieFactory.  
3. Click Create Disc Label. Corel Label@Once is started.  
4. Click the General tab.  
5. Choose optical disc drive for Printer. e.g.<E:>  
6. Add and customize the look of your images and text.  
7. Click Labelflash setting and choose Draw Quality.  
8. Click Print.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4-16  
Operating Basics  
How to make a DVD-Video  
Method 1: Simplified steps for making a DVD-Video from video data  
captured from a DV-Camcorder:  
1. Click Start All Programs DVD MovieFactory for TOSHIBA →  
DVD MovieFactory Launcher to launch DVD MovieFactory.  
2. Insert a DVD-RW or DVD+RW disc in Burner.  
3. Click "Capture & Import" item on the top of Corel DVD movieFactory 7  
window, then click Capture Video and press start to start capture video.  
4. Choose the capture source in your DV.  
5. Choose format: 4:3 DVD NTSC, 16:9 DVD NTSC or AVI.  
6. Press "Start capture" button to start.  
Method 2: Simplified steps for making a DVD-Video from adding video  
source:  
1. Click Start All Programs DVD MovieFactory for TOSHIBA →  
DVD MovieFactory Launcher to launch DVD MovieFactory.  
2. Click Create Video Disc New Project to invoke 2nd Launcher,  
choose your project type, then invoke DVD MovieFactory.  
3. Add source from HDD Disk by click Add Video files button to invoke  
browser dialog box.  
4. Choose the source video then go to Next page to apply Menu.  
5. After choose the menu template, press Next button to go to Burning  
Page.  
6. Choose the output type then press Burn button.  
®
How to learn more about Corel DVD MovieFactory  
Please refer to the Help and Manual files for additional DVD MovieFactory  
information.  
Opening the DVD MovieFactory Manual Start All Programs DVD  
MovieFactory for TOSHIBA DVD MovieFactory User Manual  
How to make a Blu-ray disc Movie  
1. Click Start All Programs DVD MovieFactory for TOSHIBA →  
DVD MovieFactory Launcher to launch DVD MovieFactory.  
2. Click Create Video Disc New Project to invoke 2nd Launcher,  
choose Blu-ray, then invoke DVD MovieFactory.  
3. Add source from HDD by click Add Video files button to invoke  
browser dialog box.  
4. Choose the source video then go to Next page to apply Menu.  
5. After choose the menu template, press Next button to go to Burning  
Page.  
6. Choose the output type then press Burn button.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4-17  
Operating Basics  
Important information for use  
Note the following limitations when you write Video DVD:  
1. Editing digital video:  
Log in with Administrator rights to use DVD MovieFactory.  
Make sure that your computer is running on AC power when using  
DVD MovieFactory.  
Operate the computer at Full Power. Do not use power-saving  
features.  
While you are editing DVD, you can display preview. However, if  
another application is running. The preview might not display  
properly.  
DVD MovieFactory cannot edit or play copy-protected content.  
Do not enter Sleep or Hibernation Mode while using DVD  
MovieFactory.  
Do not operate DVD MovieFactory immediately after turning on the  
computer. Please wait until all Disc Drive activity has stopped.  
When recording to a DV-Camcorder, to ensure you capture all of  
your data, let the camcorder record for a few seconds before you  
begin recording your actual data.  
CD recorder, JPEG functions, DVD-Audio, mini DVD and Video CD  
functions are not supported in this version.  
While recording video to DVD, please close all other programs.  
Do not run software like a screen saver because it can put a heavy  
load on the CPU.  
There is no support for mp3 decode and encode.  
2. Before recording the video to DVD:  
When you record DVD disc, please use only discs recommended by  
the Drive manufacturer.  
Do not set the working drive to a slow device like a USB1.1 hard  
disk drive or it will fail to write DVD.  
Do not perform any of the following actions:  
Operate the computer for any other function, including using a  
mouse or Touch Pad, or closing/opening the display panel.  
Bump or cause vibration to the computer.  
Use the Mode control button and Audio/Video control button to  
reproduce music or voice.  
Open the DVD drive.  
Install, remove or connect external devices, including the  
following: SD/SDHC memory card, USB device, external display,  
and optical digital devices.  
Please verify your disc after recording important data.  
DVD-R/+R/+RW disc cannot be written in VR format.  
There is no support to output VCD and SVCD formats.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4-18  
Operating Basics  
3. About Straight to Disc:  
There is no support to record on DVD-R/+R disc  
There is no support to record DVD+VR format by HDV  
HDV support is limited to burn DVD-Video only  
DVD-VR format is not supported to add Menu  
4. About recorded DVDs:  
Some DVD-ROM drives for personal computers or other DVD  
players may not be able to read DVD-R/+R/-RW/-RAM discs.  
If you use an over-used rewritable disc, the full formatting might be  
locked. Please use a brand new disc.  
TOSHIBA DVD Player  
Please be aware of the following limitations when you use the TOSHIBA  
DVD PLAYER:  
Notes on use  
Frame dropping, audio skipping or out of sync audio and video may  
occur during playback of some DVD Video titles.  
Close all other applications when using the "TOSHIBA DVD PLAYER".  
Do not open any other applications or carry out any other operations  
during DVD Video playback. Playback may stop or not function properly  
in some situations.  
Unfinalized DVDs created on home DVD recorders may not be playable  
on the computer.  
Use DVD-Video discs with a region code which is either "the same as  
the factory default setting" or "ALL".  
Do not playback DVD discs Video while watching or recording television  
programs using other applications. Doing so may cause DVD Video  
playback or television program recording errors. In addition, if  
prescheduled recording starts during DVD Video playback it may cause  
DVD Video playback or television program recording errors. Please  
view DVD Video during times when there is no recording prescheduled.  
The resume function cannot be used with some discs on the "TOSHIBA  
DVD PLAYER".  
It is recommended the AC adaptor be connected when playing  
DVDVideo. Power saving features may interfere with smooth playback.  
When playing DVD-Video using battery power, set the Power Options to  
"High performance".  
Screen savers will not display while playing a movie in the "TOSHIBA  
DVD PLAYER". The computer will also not go into Sleep Mode,  
Hibernation Mode or shutdown while using "TOSHIBA DVD PLAYER".  
Do not configure the Display automatic power off function to run while  
the "TOSHIBA DVD PLAYER" is running.  
Do not switch to Hibernation or Sleep Mode when running the  
"TOSHIBA DVD PLAYER".  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4-19  
Operating Basics  
Do not lock the computer using the Windows logo (  
) + L keys or  
the Fn + F1 keys when running the "TOSHIBA DVD PLAYER".  
Display Devices & Audio  
1. "TOSHIBA DVD PLAYER" will only run when "Colors" is set to "True  
Color (32 bit)". The "Colors" setting can be adjusted on the "Monitor"  
tab in the "Display Settings". To open the Display Settings, click Start  
Control Panel Appearance and Personalization / Appearance  
Display Change display settings Advanced settings.  
2. If the DVD Video image is not displayed on an external display or  
television, stop the "TOSHIBA DVD PLAYER", and change the screen  
resolution in "Resolution" on the "Adjust screen resolution". To open the  
"Adjust screen resolution", click Start Control Panel Appearance  
and Personalization / Appearance Display Adjust resolution.  
However, video cannot be output to some external displays and  
televisions due to output or playback conditions.  
3. When viewing DVD-Video on an external display or TV, change the  
display device before playing. DVD-Video cannot be displayed  
simultaneously (in clone mode) on both the computer's display panel  
and an external display.  
4. Do not change the screen resolution while running the "TOSHIBA DVD  
PLAYER".  
TOSHIBA DVD PLAYER  
1. "TOSHIBA DVD PLAYER" software is supported for playback of DVD-  
Video and DVD-VR.  
2. The "TOSHIBA DVD PLAYER" does not have a parental control  
function.  
3. In order to protect copyrights, the Windows Print Screen function is  
disabled when "TOSHIBA DVD PLAYER" is running.  
4. (Print Screen functions are disabled even when running other  
applications besides "TOSHIBA DVD PLAYER" and when "TOSHIBA  
DVD PLAYER" is minimized.) Please close the "TOSHIBA DVD  
PLAYER" to use the Print Screen function.  
5. Carry out the installation/uninstallation of the "TOSHIBA DVD PLAYER"  
under a user account with administrator rights.  
6. Do not change Windows Users while "TOSHIBA DVD PLAYER" is  
running.  
7. For some DVD Video discs, using the control window to change the  
audio track will also change the subtitle track.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4-20  
Operating Basics  
Starting TOSHIBA DVD PLAYER  
Use the following procedure to start "TOSHIBA DVD PLAYER".  
1. Insert an DVD-Video in the DVD Super Multi drive while Windows® 7 is  
running. When an DVD-Video disc is set in the DVD drive, the following  
application selection screen may appear. If this occurs, select Play DVD  
movie, then click OK to launch the TOSHIBA DVD PLAYER.  
2. Touch the CD/DVD panel on the Front operation panel. Or select Start →  
All Programs TOSHIBA DVD PLAYER to start "TOSHIBA DVD  
PLAYER".  
Operating TOSHIBA DVD PLAYER  
Notes on Using "TOSHIBA DVD PLAYER".  
1. Screen display and available features may vary amongst DVD-Videos  
and scenes.  
2. Only operation buttons (including remote controller and Front operation  
panels) which correspond to currently available and active features will  
be useable during DVD playback.  
3. If the menu is opened in the Display Area using the Control window's  
Top Menu or Menu buttons, touch pad and mouse menu operations  
may not be able to be used.  
Open TOSHIBA DVD PLAYER HELP  
TOSHIBA DVD PLAYER features and instructions are also explained in  
detail in "TOSHIBA DVD PLAYER Help". Use the following procedure to  
open "TOSHIBA DVD PLAYER Help".  
Click the "Help" button ( ) in the Display Area.  
Using WinDVD BD for TOSHIBA  
Notes on use  
"WinDVD BD for TOSHIBA" is for Blu-ray Disc playback only. DVD  
playback is not supported. Please use "TOSHIBA DVD PLAYER" for  
DVD playback.  
Playback of high bit rate content may cause frame dropping, audio  
skipping or decrease in computer performance.  
Close all other applications before playing back Blu-ray Disc. Do not  
open any other applications or carry out any other operations during  
Blu-ray Disc playback.  
Because Blu-ray Disc playback operates according to programs built-  
into the content, operation methods, operation screens, sound effects,  
icons and other features may vary from disc to disc. For more  
information on these items refer to instructions included with content or  
contact the content manufacturers directly.  
Make sure to connect the computer's AC adapter when playing a Blu-  
ray Disc.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4-21  
Operating Basics  
"WinDVD BD for TOSHIBA" supports AACS (Advanced Accesss  
Control System) copy protection technology. Renewal of the AACS key  
integrated into this product is required for uninterrupted enjoyment of  
Blu-ray Disc. An Internet connection is required for renewal. AACS key  
renewal is provided free of charge for 5 years after the purchase of this  
product, however renewal beyond 5 years is subject to conditions  
specified by the software provider, Corel Corporations.  
Do not playback Blu-ray Disc while recording television programs using  
"Windows Media Center" "My TV" or other applications. Doing so may  
cause Blu-ray Disc playback or television program recording errors. In  
addition, if pre-scheduled recording starts during Blu-ray Disc playback  
it may cause Blu-ray Disc playback or television program recording  
errors. Please view Blu-ray Disc video during times when there is no  
recording pre-scheduled.  
While playing a BD-J title, keyboard shortcut is ineffectve.  
While playing a BD-J title, resume play is ineffective.  
For interactive function for Blu-ray Discs, it may not work depends on  
contents or network situation.  
Region codes for BD drive and media Optical disc drives and their  
associated media are manufactured according to the specifications of  
three marketing regions. Region codes can be set from WinDVD BD  
([Region] tab in [Setup] dialogue). When you purchase BD Video, make  
sure it matches your drive, otherwise it will not play properly.  
To playback video on external display or TV using "WinDVD BD for  
TOSHIBA", output devices like display or TV which have RGB or HDCP  
supported HDMI port.  
The Blu-ray disc movie can be played only with internal LCD display or  
external devices connected by RGB and HDMI output. WinDVD does  
not support Clone mode (DualView) which plays on internal LCD and  
external display or TV.  
This product does not play HD DVD discs. Blu-ray discs with high-  
definition content required for HD viewing.  
Do not sleep or hibernate PC while WinDVD BD for TOSHIBA is  
running. When you need it, exit WinDVD BD for TOSHIBA in advance.  
Media care  
This section provides tips on protecting data stored on your CD's, DVD's,  
BD's and floppy diskettes. Handle your media with care. Following the  
simple precautions listed below will increase the lifetime of your media and  
protect the data stored on it.  
CD/DVD/BDs  
1. Store your CD's, DVD's and BD's in the containers they originally came  
in to protect them and keep them clean.  
2. Do not bend the CD's, DVD's and BD's.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4-22  
     
Operating Basics  
3. Do not write on, apply a sticker to, or otherwise mar the surface of the  
CD, DVD or BD that contains the data.  
4. Hold the CD, DVD or BD by its outside edge or the edge on the center  
hole - any fingerprints on the surface of the disc can prevent the drive  
from properly reading data.  
5. Do not expose the CD, DVD or BD to direct sunlight, extreme heat or  
cold.  
6. Do not place heavy objects on your CD's, DVD's or BD's.  
7. If your CD's, DVD's or BD's become dusty or dirty, wipe them with a  
clean dry cloth from the center hole outwards - do not wipe in a circular  
direction. If necessary, you can use a cloth that has been lightly  
dampened in water or a neutral cleaner but you must not use benzine,  
thinner or any similar cleaning solution.  
Floppy diskettes  
The USB floppy diskette drive is available only as an option.  
1. Store your floppy diskettes in the container they came in to protect them  
and keep them clean. If a floppy diskette becomes dirty, clean it with a  
soft, lightly dampened cloth - do not use cleaning fluid.  
2. Never open the shutter or touch the magnetic surface of your floppy  
diskette - doing this could permanently damage it and lose data.  
3. Always handle floppy diskettes with care to prevent the loss of stored  
data.  
4. Always apply the floppy diskette label in the correct location and never  
apply a new label on top of an existing one - in this instance the label  
could come loose and damage the floppy diskette drive.  
5. Never use a pencil for writing on a floppy diskette label as the dust from  
the pencil lead could cause a system malfunction if it found its way onto  
the computer's components. In this instance, always use a felt-tipped  
pen and write the label first before applying it to the floppy diskette.  
6. Never put a floppy diskette in a location where water or other liquid may  
make contact with it, or where it is excessively damp - either of these  
conditions could cause data loss.  
7. Never use a wet or damp floppy diskette - this could damage the floppy  
diskette drive or other devices within the computer.  
8. Data may be lost if the floppy diskette is twisted, bent, or exposed to  
direct sunlight, extreme heat or cold.  
9. Do not place heavy objects on your floppy diskettes.  
10. Do not eat, smoke, or use items such as erasers near your floppy  
diskettes as foreign particles inside the jacket of the floppy diskette can  
damage the magnetic surface.  
11. Magnetic energy can destroy the data on your floppy diskettes. In view  
of this you should keep your floppy diskettes away from speakers,  
radios, televisions and other sources of magnetic fields.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4-23  
Operating Basics  
Sound system  
This section describes some of the audio control functions.  
Adjusting System Volume  
You can control the overall level of sound using Windows Volume Mixer.  
To launch Volume Mixer, follow the steps below.  
1. Locate the Speaker icon on the task tray.  
2. Right-click the Speaker icon on the task tray.  
3. Select Open Volume Mixer from the menu.  
Click the Device button to display available playback devices. Select  
Speakers to use the internal speakers for listening. Adjust speaker volume  
by moving the slider up or down to raise or lower the volume. Click the  
Mute button  
to mute the sound.  
You may see another control under Applications in Volume Mixer. It is the  
control for an application which is currently running. The System Sounds  
is always displayed since it controls the system sounds’ volume.  
Changing System Sounds  
System sounds are assigned to inform you when certain events happen.  
This section explains how select an existing scheme or save one you have  
modified.  
To launch the configuration dialog window for system sounds, follow the  
steps below.  
1. Right-click the Speaker icon on the task tray.  
2. Select Sounds from the menu.  
Realtek HD Audio Manager  
You can confirm and change the audio configuration using the Realtek HD  
Audio Manager. To launch the Realtek HD Audio Manager, click Start →  
Control Panel Hardware and Sound Realtek HD Audio Manager.  
When you first launch the Realtek HD Audio Manager, you will see  
following device tabs. Speakers is the default output device. Microphone  
is the default input device. To change the default device, click the Set  
Default Device button under the chosen device tab.  
Speakers is the default output device. Select it when using the internal  
speakers or headphones.  
HDMI Output should be selected when connecting the HDMI cable to  
the HDMI jack for playing digital sound on digital audio equipment.  
Microphone is the default input device. It should be selected when  
using the computer’s internal microphone or an external microphone  
connected to the Microphone jack to record sound.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4-24  
     
Operating Basics  
If an external microphone or audio cable is connected to the Microphone  
jack, the Realtek HD Audio Manager Connector Settings dialog will be  
displayed allowing selection of either "Line In" or "Mic In" input.  
Information  
Click the information button  
to view hardware information, software  
information, and language setting.  
Speaker Configuration  
Click the Auto Test button  
to confirm the internal speakers or the  
headphone sound is coming from the right direction.  
Sound Effects  
This section explains how to select various sound effects.  
Environment - simulates reverberations of sound for familiar  
environments around us. You can select an existing preset in the menu.  
Equalizer - raises or lowers a frequency of sound to simulate a popular  
genre of music. You can select an existing preset in the menu.  
Karaoke - cancels the specific frequency of sound and results in the  
Voice Cancellation. Clicking the Karaoke icon, lowers the vocal sound  
within music. Using the arrow buttons will adjust the musical key of the  
sound.  
Microphone Effects  
Microphone Effects are only found within Microphone window.  
Noise Suppression reduces background noise and fan noise.  
Acoustic Echo Cancellation reduces feedback and feedback echo.  
Default Format  
You can change the sample rate and bit depth of sound.  
Using the web camera  
Some models are equipped with a Web Camera.  
Web Camera is a device that allows you to record video or take  
photographs with your computer. You can use it for video chatting or video  
conferences using a communication tool such as Windows Live  
Messenger. Toshiba web Camera Application will help you to add  
various video effects to your video or photograph.  
The Web camera enables the transmission of video and use of video chat  
via the internet using specialized applications.  
The effective pixel count for this web camera is 0.3 million or 1.0 million  
(0.3M maximum photograph size: 640X480 pixels; 1M maximum  
photograph size: 1280X800 pixels).  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4-25  
   
Operating Basics  
3
2
1
1. Microphone  
2. Web Camera  
3. Web Camera LED  
Figure 4-8 Web Camera  
Make sure to remove the protective plastic-film before using the Web  
Camera.  
Do not point the web camera directly at the sun.  
Do not touch or press strongly on the web camera lens. Doing so may  
reduce image quality. Use an eyeglass cleaner (cleaner cloth) or other  
soft cloth to clean the lens if it becomes dirty.  
Setting the image "SIZE" to more than "800x600" will cause a larger  
amount of data to be written to the hard disk drive and may interfere  
with smooth recording.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4-26  
Operating Basics  
Using TOSHIBA Web Camera Application  
TOSHIBA Web Camera Application is pre-configured to start when you turn  
on Windows® 7; if you need to restart it go to Start All Programs →  
TOSHIBA Utilities Web Camera Application.  
1. Capture Still Images  
2. Open/Close Preview Area  
3. Delete Recorded File  
4. Video Recording  
5. Camera Resolution  
6. Capture Settings  
Figure 4-9 Using the Software  
Capture Still Image  
Click to capture a still image, and see a preview  
of the captured image in preview area.  
Open/Close Preview  
Area  
Click to open Preview Area. One more to close  
Preview Area.  
Delete Recorded File  
Choose a thumbnail of recorded file and click this  
button to delete this file from hard disk.  
Video Recording  
Click to start recording. One more to stop  
recording and see preview of the video in  
preview area.  
Camera Resolution  
Capture Settings  
Choose resolution for Preview, Capture and  
Record.  
Open Capture Settings dialog box.  
Chooses from the Basic tab to select photo and  
video saving location, select Capture Format and  
Video Quality.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4-27  
 
Operating Basics  
Using TOSHIBA Face Recognition  
TOSHIBA Face Recognition uses a face verification library to verify the  
face data of users when they log in Windows. The user can thus avoid  
having to enter a password or the like, which makes the login process  
easier. This software is preinstalled with some models.  
TOSHIBA Face Recognition does not guarantee the correct  
identification of a user. Changes to the likeness of a registrant, such as  
hairstyle changes, wearing a cap, or wearing glasses may affect the  
recognition rates when such changes occur after the registrant had  
registered.  
TOSHIBA Face Recognition may incorrectly recognize faces that are  
similar to a registrant.  
For high security purposes, TOSHIBA Face Recognition is not a  
suitable substitute for Windows passwords. When security is a high  
priority, use your established Windows passwords to log in.  
Bright background light and/or shadows may prevent a registrant from  
being recognized correctly. In that case, log in using your Windows  
password. If recognition of a registrant fails repeatedly, refer to your  
computer documentation to learn ways to improve recognition  
performance.  
Disclaimer  
Toshiba does not guarantee that the face recognition utility technology will  
be completely secure or error-free. Toshiba does not guarantee that the  
face recognition utility will accurately screen out unauthorized users at all  
times. Toshiba is not liable for any failure or damage that might arise out of  
the use of the face recognition software or utility.  
TOSHIBA, ITS AFFILIATES AND SUPPLIERS SHALL HAVE NO  
RESPONSIBILITY FOR DAMAGE TO OR LOSS OF ANY BUSINESS,  
PROFITS, PROGRAMS DATA, NETWORK SYSTEMS OR REMOVABLE  
STORAGE MEDIA ARISING OUT OF OR RESULTING FROM THE USE  
OF THE PRODUCT, EVEN IF ADVISED OF THE POSSIBILITY  
THEREOF.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4-28  
 
Operating Basics  
How to register the Face Recognition Data  
Take a picture for facial verification purposes, and register the data needed  
when you log in. To register the data needed when you log in, follow the  
steps as described below:  
1. To launch this utility, click Start -> All Programs -> TOSHIBA ->  
Utilities -> Face Recognition.  
The Registration screen is displayed for a logged-in user whose face  
has not been registered.  
The Management screen is displayed for a logged-in user whose face  
has already been registered.  
2. Click the Register button in the Management screen. The  
Registration screen is displayed.  
If you wish to practice, click on the Next button in the Registration  
screen.  
If you do not wish to practice, click on the Skip button in the  
Registration screen.  
3. Click the Next button to start the guide.  
4. First, take a picture while moving your neck slightly to the left and right.  
5. Now take a picture while moving your neck down and up. Or click the  
Back button to practice the guide once more.  
6. Click the Next button to start image-capturing process.  
Adjust the position of your face so that it fits within the face-shaped  
frame.  
7. Once your face has been positioned properly, the recording will  
commence.  
Start moving your neck very slightly to the left and right, and then move  
your neck down and up.  
8. Registration will end after you have repeatedly moved your neck left,  
right, down and up.  
When the register succeeds, below message will be displayed on the  
screen: " Registration successful. Now we'll do the verification test.  
Click the Next button."  
Click the Next button to perform the verification test.  
9. Perform the verification test. Face the screen as you do when you  
register.  
If verification fails, click the Back button and re-register. Please refer to  
step 8 from step 6.  
10. If verification is successful, click the Next button and register an  
account.  
11. Register the account. Fill in the account registration fields. Fill in the all  
fields. When you have finished it, click Next button.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4-29  
Operating Basics  
12. The Management screen is displayed.  
The registered account name will be displayed. Clicking on it will cause  
the captured image of your face to be displayed on the left.  
How to Delete the Face Recognition Data  
Delete image data, account information, and personal record data created  
during registration. To delete the Face Recognition Data, follow the steps  
as described below:  
1. To launch this utility, click Start -> All Programs -> TOSHIBA ->  
Utilities -> Face Recognition.  
The Management screen is displayed.  
2. Select a user which is deleted in the Management screen.  
3. Click the Delete button. "You are about to delete the user data.  
Would you like to continue?" will be displayed on the screen.  
If you do not want the data to be deleted, click the No button and  
you will then be returned to the Management screen.  
Clicking on the Yes button will remove the selected user from the  
Management screen.  
How to launch the help file  
For further information on this utility, please refer to the help file.  
1. To launch the help file, click Start -> All Programs -> TOSHIBA ->  
Utilities -> Face Recognition Help.  
Windows Logon via TOSHIBA Face Recognition  
This section explains how to login to Windows with TOSHIBA Face  
Recognition. Two authentication modes are provided.  
1:N Mode Login screen: If the face authentication tile is selected by  
default, you can log in without using the keyboard or mouse.  
1:1 Mode Login screen: This mode is essentially the same as 1:N  
mode, but the Select Account screen will appear before the Display  
Captured Image screen, and you will need to select the user account  
to be authenticated in order to start the authentication process.  
1:N Mode Login screen  
1. Turn on the computer.  
2. The Select Tiles screen will be displayed.  
3. Select Start face recognition (  
).  
4. "Please face the camera" will be displayed.  
5. Verification will be performed. If the authentication is successful, the  
image data taken in step 4 will be faded in and placed over one another.  
If an error occurs during authentication, you will be returned to the  
Select Tiles screen.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4-30  
Operating Basics  
6. Windows Welcome screen will be displayed, and will be logged in  
automatically to Windows.  
1:1 Mode Login screen  
1. Turn on the computer.  
2. The Select Tiles screen will be displayed.  
3. Select Start face recognition (  
).  
4. The Select Account screen will be displayed.  
5. Select the account, and click the Arrow button.  
6. "Please face the camera" will be displayed.  
7. Verification will be performed. If the authentication is successful, the  
image data taken in step 6 will be faded in and placed over one another.  
If an error occurs during authentication, you will be returned to the  
Select Tiles screen.  
8. Windows Welcome screen will be displayed, and will be logged in  
automatically to Windows.  
If authentication was successful, but an authentication error  
subsequently occurred during the login to Windows, you will be asked  
to provide your account information.  
Modem  
This section describes how to connect and disconnect the internal modem  
to and from a telephone jack.  
Connection to any communication line other than an analog phone line  
could cause a computer system failure.  
Connect the built-in modem only to ordinary analog phone lines.  
Never connect the built-in modem to a digital line (ISDN).  
Never connect the built-in modem to the digital connector on a  
public telephone or to a digital private branch exchange (PBX).  
Never connect the built-in modem to a key telephone system for  
residences or offices.  
Avoid using your computer modem with the telephone cable connected  
during an electrical storm. There may be a remote risk of electric shock  
from lightning.  
Modem functions cannot be used in models which are not equipped  
with a modem.  
This information is applicable to the models equipped with a built-in  
modem.  
Some models are equipped with a modem jack or FM antenna port.  
User’s Manual  
4-31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Operating Basics  
Region selection  
Telecommunication regulations vary from one region to another, so you will  
need to make sure the internal modem’s settings are correct for the region  
in which it will be used.  
The built-in modem can be used only in specified countries and regions.  
Using the modem in an area not specified for use may cause a system  
failure. Check the specified areas carefully before using it.  
To select a region, follow the steps as detailed below:  
1. Click Start All Programs TOSHIBA Networking Modem  
Region Select.  
If it is available, do not use the Country/Region Select function included as  
part of the modem setup utility within the Control Panel - if you change the  
country/region setting this way you may find that the change does not take  
effect.  
2. The Region Selection icon will appear in the Windows Taskbar.  
3. Click the icon with the primary (left) mouse button to display a list of  
regions that the modem supports, together with a sub-menu which  
details telephony location information - a check mark will appear next to  
the currently selected region and telephony location.  
4. Select either a region from the region menu or a telephony location from  
the sub-menu.  
When you click a region it becomes the modem's default selection  
for any new dialing locations that are created within the Windows  
Control Panel (Phone and Modem Options).  
When you select a telephony location, the corresponding region is  
automatically selected and becomes the modem's default setting.  
Properties menu  
Click the icon with the secondary (right) mouse button in order to display a  
Properties menu on the screen.  
Setting  
Within the Properties menu you are able to either enable or disable the  
following settings:  
AutoRun Mode  
Allows you to configure whether the Modem Region Select utility starts  
automatically whenever you start up the operating system.  
Open the Dialing Properties dialog box after selecting region  
Allows you to configure whether the dialing properties dialog box will be  
displayed automatically after you have selected a region.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4-32  
   
Operating Basics  
Location list for region selection  
Displays a sub-menu appears which details location information.  
Open dialog box, if the modem and Telephony Current  
Location region code do not match  
Displays a warning if the current settings for both region code and  
telephony location are different.  
Modem Selection  
If the computer cannot recognize the internal modem, a dialog box is  
displayed from which you should select the appropriate communications  
port for your modem to use.  
Dialing Properties  
You should select this item in order to display the dialing properties.  
If you are using the computer in Japan, the Telecommunications Business  
Law requires that you select Japan region mode. It is illegal to use the  
modem in Japan with any other selection.  
Connecting the modular cable  
Connection to any communication line other than an analog phone line  
could cause a computer system failure.  
Connect the built-in modem only to ordinary analog phone lines.  
Never connect the built-in modem to a digital line (ISDN).  
Never connect the built-in modem to the digital connector on a  
public telephone or to a digital private branch exchange (PBX).  
Never connect the built-in modem to a key telephone system for  
residences or offices.  
Avoid using your computer modem with the telephone cable connected  
during an electrical storm. There may be a remote risk of electric shock  
from lightning.  
To connect the modem's modular cable, follow the steps as detailed below:  
1. Plug the end of the modular cable into the computer's modem jack.  
2. Plug the other end of the modular cable into a telephone jack.  
Figure 4-10 Connecting the internal modem  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4-33  
 
Operating Basics  
Do not pull on the cable or move the computer while the cable is  
connected.  
Disconnecting the modular cable  
To disconnect the modular cable, follow the steps as detailed below:  
1. Pinch the lever on the plug in the telephone jack and pull it out from  
within the connector.  
2. Pinch the lever on the plug in the computer's modem jack and pull it out  
from within the computer.  
Wireless communications  
The computer's wireless communication function supports both Wireless  
LAN and Bluetooth devices.  
Some models are equipped with both Wireless LAN and Bluetooth  
functions.  
Wireless LAN  
The Wireless LAN is compatible with other LAN systems based on Direct  
Sequence Spread Spectrum/Orthogonal Frequency Division Multiplexing  
radio technology that complies with the IEEE802.11 Wireless LAN  
standard.  
Frequency Channel Selection of 5GHz for IEEE 802.11a or n 2.0  
Frequency Channel Selection of 2.4GHz for 802.11b/g or n 2.0  
Roaming over multiple channels  
Card power management  
Wired Equivalent Privacy (WEP) data encryption based on an 128-bit  
encryption algorithm  
Wi-Fi Protected Access™ (WPA™) support  
Advanced Encryption Standard (AES) data encryption  
The transmission speed over the wireless LAN, and the distance over  
which the wireless LAN can reach, may vary depending on surrounding  
electromagnetic environment, obstacles, access point design and  
configuration, client design and software/hardware configurations. The  
transmission rate described is the theoretical maximum speed as specified  
under the appropriate standard - the actual transmission speed will be  
lower than the theoretical maximum speed.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4-34  
       
Operating Basics  
Setting  
1. Click Start Control Panel Network and Internet Network and  
Sharing Center Connect to a network.  
2. Choose a wireless network from the available connection window and  
click Connect.  
3. Follow the wizard. You will need the name of the wireless network  
together with security settings. Consult the documentation  
accompanied with your router or ask your wireless network  
administrator for the settings.  
Security  
TOSHIBA strongly recommend that you enable encryption functionality,  
otherwise your computer will be open to illegal access by an outsider  
using a wireless connection. If this occurs, the outsider may illegally  
access your system, eavesdrop, or cause the loss or destruction of  
stored data.  
TOSHIBA is not liable for the loss of data due to eavesdropping or  
illegal access through the wireless LAN and the damage thereof.  
Bluetooth wireless technology  
Bluetooth™ wireless technology eliminates the need for cables, such as  
desktop computers, between your PC and other electronic devices,  
example of printers and mobile phones.  
You cannot use the computer's built-in Bluetooth functions and an external  
Bluetooth adaptor simultaneously.  
For reference, Bluetooth wireless technology has the following features:  
Worldwide operation  
The Bluetooth radio transmitter and receiver operate in the 2.4GHz band,  
which is license-free and compatible with radio systems in most countries  
in the world.  
Radio links  
You can easily establish links between two or more devices, with these  
links being maintained even if the devices are not within a line-of-sight of  
each other.  
Security  
Two advanced security mechanisms ensure a high level of security:  
Authentication prevents access to critical data and makes it impossible  
to falsify the origin of a message.  
Encryption prevents eavesdropping and maintains link privacy.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4-35  
 
Operating Basics  
BluetoothTM Stack for Windows by TOSHIBA  
Please note that this software is specifically designed for the following  
operating systems:  
Windows 7  
Information regarding the use of this software with these operating systems  
is listed below, with further details being contained with the electronic help  
files supplied with the software.  
This Bluetooth Stack is based on the Bluetooth Version 2.1+EDR  
specification. However, TOSHIBA cannot confirm the compatibility  
between any computing products and/or other electronic devices that use  
Bluetooth, other than TOSHIBA notebook computers.  
Release Notes related to the Bluetooth® Stack for Windows®  
by TOSHIBA  
1. Fax application software:  
Please be aware that there is some fax application software that you  
cannot use on this BluetoothTM Stack.  
2. Multi-user considerations:  
On Windows® 7, the use of Bluetooth is not supported in a  
multi-user environment. This means that, when you use Bluetooth,  
other users that are logged into the same computer will not be able  
to use this type of functionality.  
Product Support:  
The latest information regarding operating system support, language  
support or available upgrades can be found on our website  
http://www.toshiba-europe.com/computers/tnt/bluetooth.htm in Europe or  
www.pcsupport.toshiba.com in the United States.  
Wireless communication indicator  
The wireless communication indicator shows the status of the computer's  
wireless communication functions.  
Indicator status  
Indicator off  
Indication  
No wireless functionality is available.  
Indicator glows  
Wireless LAN or Bluetooth is turned on by an  
application.  
If you used the Taskbar to disable the wireless LAN, restart the computer or  
perform the following procedure to re-enable it: Click Start, open Control  
Panel, click System and Security, click Device Manager on System  
category, double-click Network Adapters, and right click the wireless  
device then choose Enable.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4-36  
Operating Basics  
Do not use the Wireless LAN (Wi-Fi) or Bluetooth functionalities near a  
microwave oven or in areas subject to radio interference or magnetic  
fields. Interference from a microwave oven or other source can disrupt  
Wi-Fi or Bluetooth operation.  
Turn Wi-Fi and Bluetooth functionalities off when near a person who  
may have a cardiac pacemaker implant or other medical electric  
device. Radio waves may affect pacemaker or medical device  
operation, possibly resulting in serious injury. Follow the instruction of  
your medical device when using any Wi-Fi or Bluetooth functionality.  
Always turn off Wi-Fi or Bluetooth functionality if the computer is near  
automatic control equipment or appliances such as automatic doors or  
fire detectors. Radio waves can cause malfunction of such equipment,  
possibly resulting in serious injury.  
It may not be possible to make a network connection to a specified  
network name using the ad hoc network function.  
If this occurs, the new network(*) will have to be configured for all  
computers connected to the same network in order to re-enable  
network connections.  
* Please be sure to use new network name.  
LAN  
The computer has built-in support for Ethernet LAN (10 megabits per  
second, 10BASE-T) and Fast Ethernet LAN (100 megabits per second,  
100BASE-TX). This section describes how to connect/disconnect to a LAN.  
Do not install or remove a memory module while Wake-up on LAN is  
enabled.  
The Wake-up on LAN function consumes power even when the system  
is off. Leave the AC adaptor connected while using this feature.  
The Link speed (10/100 megabits per second) changes automatically  
depending on the network conditions (connected device, cable or  
noise, and so on).  
LAN cable types  
The computer must be configured properly before connecting to a LAN.  
Logging onto a LAN using the computer's default settings could cause a  
malfunction in LAN operation. Check with your LAN administrator  
regarding set-up procedures.  
If you are using Fast Ethernet LAN (100 megabits per second, 100BASE-  
TX), be sure to connect with a CAT5 cable or higher. You cannot use a  
CAT3 cable.  
If you are using Ethernet LAN (10 megabits per second, 10BASE-T), you  
can connect with a CAT3 or higher cable.  
User’s Manual  
4-37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Operating Basics  
Connecting the LAN cable  
Connect the AC adaptor before connecting the LAN cable. The AC  
adaptor must remain connected during LAN use. If you disconnect the  
AC Adaptor while the computer is accessing a LAN, the system may  
hang up.  
Do not connect any other cable to the LAN jack except the LAN cable.  
Otherwise, malfunctions or damage may occur.  
Do not connect any power supplying device to the LAN cable that is  
connected to the LAN jack. Otherwise, malfunctions or damage may  
occur.  
To connect the LAN cable, follow the steps as detailed below:  
1. Turn off the power to the computer and to all external devices  
connected to the computer.  
2. Plug one end of the cable into the LAN jack. Press gently until you hear  
the latch click into place.  
Figure 4-11 Connecting the LAN cable  
3. Plug the other end of the cable into a LAN hub connector or router.  
Check with your LAN administrator and hardware or software vendor  
before using or configuring a network connection.  
When the computer is exchanging data with the LAN, the LAN Active  
indicator glows yellow. When the computer is connected to a LAN hub but  
is not exchanging data, the Link indicator glows.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4-38  
 
Operating Basics  
Disconnecting the LAN cable  
Make sure the LAN Active indicator (amber LED) is out before you  
disconnect the computer from the LAN.  
To disconnect the LAN cable, follow the steps as detailed below:  
1. Pinch the lever on the connector in the computer’s LAN jack and pull  
out the connector.  
2. Disconnect the cable from the LAN hub or router in the same manner.  
Check with your LAN administrator and hardware or software vendor  
before disconnecting from the hub.  
Cleaning the computer  
To help ensure long, trouble-free operation, keep the computer free of dust  
and dirt, and use care with all liquids around it.  
Be careful not to spill liquids into the computer. If the computer does get  
wet, turn the power off immediately and let the computer dry completely -  
in these circumstance you should get the computer inspected by an  
authorized service provider in order to assess the scope of any damage.  
Clean the plastics of the computer using a slightly water dampened  
cloth.  
You can clean the display screen by spraying a small amount of glass  
cleaner onto a soft, clean cloth and then wiping the screen gently with  
the cloth.  
Using a cleaning cloth  
A cleaning cloth can be used to wipe away dust and fingerprints from the  
keyboard and palm rest area of your computer.  
When wiping the keyboard, palm rest and display panel, do so gently  
without using excessive pressure.  
Do not use a cleaning cloth when it is dirty or wet.  
Do not use a cleaning cloth soaked with water, detergents or volatile  
organic solvents.  
It is recommended that you wash the cloth if it gets soiled using a gentle,  
mild detergent and rinse it well. Allow it to air dry completely before using it  
again on your computer.  
Never spray cleaner directly onto the computer or let liquid run into any  
part of it. Never use harsh or caustic chemical products to clean the  
computer.  
Use a cleaning cloth to wipe away dust, fingerprints and similar from  
the keyboard, palm rest and other parts.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4-39  
     
Operating Basics  
Moving the computer  
While the computer is designed for rugged durability you should exercise a  
few simple precautions when moving it in order to help ensure trouble-free  
operation.  
Make sure all disk/disc activity has ended before moving the computer -  
check that the HDD and other indicators on the front of the computer  
are off.  
If a CD, DVD or BD is in the drive, remove it and make sure that the disc  
tray is securely closed.  
Turn off (shut down) the computer.  
Disconnect the AC adaptor and all peripherals before moving the  
computer.  
Close the display panel.  
Do not pick up the computer by its display panel.  
Before carrying your computer, shut it down, disconnect the AC adaptor  
and allow it to cool down - a failure to follow this instruction may result in  
minor heat injury.  
Be careful not to subject the computer to impact or shock - a failure to  
follow this instruction could result in damage to the computer, computer  
failure or loss of data.  
Never transport your computer with any cards installed - this may cause  
damage to either the computer and/or the card resulting in product  
failure.  
Always use a suitable carry case when transporting the computer.  
When carrying your computer, be sure to hold it securely so that it does  
not fall or hit anything.  
Do not carry your computer by holding any of its protruding elements.  
Heat dispersal  
To protect from overheating, the CPU has an internal temperature sensor. If  
the computer’s internal temperature rises to a certain level, the cooling fan  
is turned on or the processing speed is lowered. You can select whether to  
control the CPU temperature by turning on the fan first, then if necessary,  
lowering the CPU speed. Or, by lowering the CPU speed first, then if  
necessary, turning on the fan. These functions are controlled within the  
Power Options.  
When the CPU temperature falls to a normal range, the fan is turned off  
and the CPU operation returns to standard speed.  
If the CPU temperature reaches an unacceptably high level with either  
setting, the system automatically shuts down to prevent damage. Data in  
memory will be lost.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4-40  
     
Chapter 5  
The Keyboard  
The computer's keyboard layouts are compatible with a 104/105-key  
enhanced keyboard - by pressing some keys in combination, all of the  
104/105-key enhanced keyboard functions can be performed on the  
computer.  
The number of keys available on your keyboard will depend on which  
country/region your computer is configured for, with keyboards being  
available for numerous languages.  
In use there are six different types of keys, specifically typewriter keys,  
function keys, soft keys, Hot keys and Windows special keys.  
Typewriter keys  
The typewriter keys produce the upper-case and lower-case letters,  
numbers, punctuation marks, and special symbols that appear on the  
screen. However, there are some differences between using a typewriter  
and using a computer keyboard:  
Letters and numbers produced in computer text vary in width. Spaces,  
which are created by a 'space character' may also vary depending on  
line justification and other factors.  
The lowercase l (el) and the number 1 (one), together with the  
uppercase O (oh) and the 0 (zero), are not interchangeable on  
computers as they are on a typewriter.  
The CAPS LOCK function key locks only the alphabetic characters into  
upper-case while the Shift Lock function on a typewriter places all keys  
in the shifted position.  
The SHIFT keys, the Tab key, and the BACK SPACE key perform the  
same function as their typewriter counterparts but also have special  
computer functions.  
Never remove the key caps on your keyboard. Doing so could cause  
damage to the parts under the key caps.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5-1  
           
The Keyboard  
Function keys: F1 … F9  
The function keys (not to be confused with the special FN key) are the  
twelve keys at the top of your keyboard - these keys function differently  
from other keys.  
F1 through F9 are called function keys because they execute programmed  
functions when pressed and, when used in combination with the FN key,  
those keys marked with icons also execute specific functions on the  
computer. Please refer to the section, Soft keys: FN key combinations, in  
this chapter for further information, taking care to note that the function  
executed by individual keys will depend on the software you are using.  
Soft keys: FN key combinations  
The FN (function) key is unique to TOSHIBA computers and is used in  
combination with other keys to form soft keys. Soft keys are key  
combinations that enable, disable or configure specific features.  
Please note that some software may disable or interfere with soft-key  
operations, and that the soft-key settings are not restored when the  
computer returns from Sleep Mode.  
Emulating keys on an enhanced keyboard  
Figure 5-1 A 104-key enhanced keyboard layout  
This computer's keyboard is designed to provide all the features of the 104-  
key enhanced keyboard.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5-2  
           
The Keyboard  
Hot keys  
Hot keys (pressing FN + a function or ESC key) let you enable or disable  
certain features of the computer.  
Mute: Pressing FN + ESC turns the volume on and off.  
Lock: Pressing FN + F1 enters ''Lock computer mode''. To restore your  
desktop, you need to log on again.  
Power Plan: Pressing FN + F2 changes the power settings.  
Sleep: Pressing FN + F3 switches the system to Sleep mode.  
Hibernate: Pressing FN + F4 switches the system to Hibernate mode.  
Output: Pressing FN + F5 changes the active display device.  
Brightness (Down): Pressing FN + F6 decreases the computer's display  
panel brightness in individual steps.  
User’s Manual  
5-3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                                 
The Keyboard  
Brightness (Up): Pressing FN + F7 increases the computer's display panel  
brightness in individual steps.  
Wireless: Pressing FN + F8 switches the active wireless devices.  
If no wireless communication device is installed, no dialog box will appear.  
Touch Pad: Pressing FN + F9 enables or disables the Touch Pad function.  
Zoom: Pressing FN + Space changes the display resolution.  
TOSHIBA Zooming Utility (reduce): Pressing FN + 1 reduces the icon  
size on the desktop or the font sizes within one of the supported application  
windows.  
TOSHIBA Zooming Utility (enlarge): Pressing FN + 2 enlarges the icon  
size on the desktop or the font sizes within one of the supported application  
windows.  
FN Sticky key  
You can use the TOSHIBA Accessibility Utility to make the FN key sticky,  
that is, you can press it once, release it, and then press an "F Number"  
key. To start the TOSHIBA Accessibility utility, click Start J All Programs  
J TOSHIBA J Utilities J Accessibility.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5-4  
                         
The Keyboard  
Windows special keys  
The keyboard provides two keys that have special functions in Windows:  
Windows Start Button activates the Start menu and the other, the  
application key, has the same function as the secondary mouse button.  
This key activates the Windows Start menu.  
This key has the same function as the secondary (right) mouse button.  
Generating ASCII characters  
Not all ASCII characters can be generated using normal keyboard  
operation, but you are able to generate these characters using their specific  
ASCII codes.  
1. Hold down ALT + FN.  
2. Type the ASCII code of the character you require.  
3. Release ALT + FN - the ASCII character will appear on the display  
screen.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5-5  
       
Chapter 6  
Power and Power-up Modes  
The computer's power resources include the AC adaptor and internal  
batteries. This chapter gives details on making the most effective use of  
these resources including charging and changing batteries, tips for saving  
battery power, and power-up modes.  
Power conditions  
The computer's operating capability and battery charge status are affected  
by different power conditions, including whether an AC adaptor is  
connected, whether a battery pack is installed and what the charge level is  
for that battery.  
Table 6-1 Power conditions  
Power on  
Power off  
(no operation)  
AC  
adaptor  
connected  
Battery fully  
charged  
• Operates  
• LED: Battery green  
• LED: Battery green  
DC IN green  
DC IN green  
Battery partially • Operates  
charged or no  
• Quick charge  
• Quick Charge  
• LED: Battery amber  
DC IN green  
charge  
• LED: Battery amber  
DC IN green  
No battery  
installed  
• Operates  
• No charge  
• No charge  
• LED: Battery off  
DC IN green  
• LED: Battery off  
DC IN green  
User’s Manual  
6-1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
         
Power and Power-up Modes  
Table 6-1 Power conditions continued  
Power on  
Power off  
(no operation)  
AC  
adaptor  
not  
Battery charge  
is above low  
battery trigger  
• Operates  
• LED: Battery off  
DC IN off  
connected point  
Battery charge  
• Operates  
is below low  
battery trigger  
point  
• LED: Battery  
flashes Amber  
DC IN off  
Battery charge Computer goes into Sleep  
is exhausted  
Mode and shuts down  
No battery  
installed  
• Cannot operate  
• LED: Battery off  
DC IN off  
Power indicators  
As shown in the below table, the Battery, DC IN and Power indicators on  
the system indicator alert you to the computer’s operating capability and  
battery charge status.  
Battery indicator  
Check the Battery indicator to determine the status of the battery pack -  
the following indicator conditions should be noted:  
The battery charge is low, the AC adaptor must  
be connected in order to recharge the battery.  
Flashing amber  
Indicates the AC adaptor is connected and the  
battery is charging.  
Amber  
Indicates the AC adaptor is connected and the  
battery is fully charged.  
Green  
Under any other conditions, the indicator does  
not light.  
No light  
If the battery pack becomes too hot while it is being charged, the charge  
will stop and the Battery indicator will go out. When the battery pack's  
temperature falls to a normal range, charging will resume - this process will  
occur regardless of whether the computer's power is on or off.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
6-2  
     
Power and Power-up Modes  
DC IN indicator  
Check the DC IN indicator to determine the power status with the AC  
adaptor connected - the following indicator conditions should be noted:  
Indicates the AC adaptor is connected and is  
correctly supplying power to the computer.  
Green  
Under any other conditions, the indicator does not  
light.  
No light  
Power indicator  
Check the Power indicator to determine the power status of the computer -  
the following indicator conditions should be noted:  
Indicates power is being supplied to the computer  
and the computer is turned on.  
Green  
Indicates that the computer is in Sleep Mode and  
Blinking amber  
that there is sufficient power available (AC  
adaptor or battery) to maintain this condition. In  
Sleep Mode, this indicator will turn on for one  
second and off for one second.  
Under any other conditions, the indicator does  
not light.  
No light  
Battery types  
The computer has two different types of batteries:  
Battery pack  
Real Time Clock (RTC) battery  
Battery pack  
When the AC adaptor is not connected, the computer's main power source  
is a removable lithium ion battery pack, also referred to in this manual as  
the battery. You can purchase additional battery packs for extended use of  
the computer away from an AC power source - although you should not  
change the battery pack while the AC adaptor is connected.  
Before you remove the battery pack, save your data and shut down the  
computer, or place the computer into Hibernation Mode. Please be aware  
that, when placing the computer into Hibernation Mode, the contents of  
memory will be saved to the hard disk drive, although for safety sake, it is  
best to also save your data manually.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
6-3  
       
Power and Power-up Modes  
The battery pack is a lithium ion battery, which can explode if not  
properly replaced, used, handled or disposed of. Dispose of the battery  
as required by local ordinances or regulations. Use only batteries  
recommended by TOSHIBA as replacements.  
Do not remove the battery pack while the computer is in Sleep Mode. In  
this mode data is stored in memory, so if the computer loses power, it  
will be lost.  
Battery type (depending on the model you purchased)  
The availability of this battery is dependent on the model you  
purchased.  
Real Time Clock battery  
The Real Time Clock (RTC) battery provides power for the internal real  
time clock and calendar function and also maintains the system  
configuration while the computer is turned off. If the RTC battery becomes  
completely discharged, the system will lose this information and the real  
time clock and calendar will stop working - in this instance the following  
message will be displayed when you turn on the power:  
ERROR 0271: Check date and time settings.  
WARNING 0251: System CMOS checksum bad - Default  
S
configuration used.  
Press <F1> to resume, <F2> to Setup.  
The computer's RTC battery is a lithium battery and should be replaced  
only by your dealer or by a TOSHIBA service representative. The battery  
can explode if not properly replaced, used, handled or disposed of.  
Dispose of the battery as required by local ordinances or regulations.  
When this error appears, the following action is recommended.  
1. Connect the AC adapter and let the battery charge for 24-hours.  
2. Press F2 to enter BIOS setup menu.  
3. Set correct time and date.  
If you still see the error message after performing the above actions,  
please contact your TOSHIBA service representative.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
6-4  
 
Power and Power-up Modes  
Care and use of the battery pack  
The battery pack is a vital component of portable computing and, as such,  
taking proper care of it will help ensure a longer operating time on battery  
power as well as deliver a longer life for your battery pack. The instructions  
detailed in this section will help to ensure safe operation and maximum  
performance.  
Refer to the enclosed Instruction Manual for Safety and Comfort for  
detailed precautions and handling instructions.  
Make sure the battery is securely installed in the computer before  
attempting to charge the battery pack. Improper installation could  
generate smoke or fire, or cause the battery pack to rupture.  
Keep the battery pack out of reach of infants and children. It can cause  
injury.  
The battery pack is a lithium ion battery, which can explode if not  
replaced, used, handled or disposed of properly. Dispose of the battery  
as required by local ordinances or regulations. Use only batteries  
recommended by TOSHIBA as replacements.  
Charge the battery pack only in an ambient temperature between 5 and  
35 degrees Celsius. Otherwise, the electrolyte solution might leak,  
battery pack performance might deteriorate and the battery life might  
be shortened.  
Never install or remove the battery pack without first turning off the  
power and disconnecting the AC adaptor. Never remove the battery  
pack while the computer is in Sleep Mode. Data will be lost.  
Never remove the battery pack while the Wake-up on LAN function is  
enabled. Data will be lost. Before you remove a battery pack, disable  
the Wake-up on LAN function.  
Charging the batteries  
When the power in the battery pack becomes low, the Battery indicator will  
flash amber to indicate that only a few minutes of battery power remain. If  
you continue to use the computer while the Battery indicator flashes, the  
computer will enable Hibernation Mode so that you do not lose any data,  
and automatically turn itself off.  
You must recharge a battery pack when it becomes discharged.  
Procedures  
To recharge a battery pack while it is installed in the computer, connect the  
AC adaptor to the DC IN 19V jack and plug the other end into a working  
outlet - the Battery indicator will glow amber while the battery is being  
charged.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
6-5  
   
Power and Power-up Modes  
Use only the computer connected to an AC power source or the optional  
TOSHIBA Battery charger to charge the battery pack. Never attempt to  
charge the battery pack with any other charger.  
Time  
The following table shows the approximate time required to fully charge a  
discharged battery.  
Charging time (hours)  
Battery type  
Power on  
Battery Pack  
(3 cell / 6 cell / 12 cell)  
about 12 or longer  
about 4 or longer  
RTC battery  
about 24  
about 24 with AC or  
Battery pack  
Please be aware that the charging time when the computer is on is  
affected by ambient temperature, the temperature of the computer and  
how you are using the computer - if you make heavy use of external  
devices for example, the battery might scarcely charge at all during  
operation. Please refer to the section Maximizing battery operating time for  
further information.  
Battery charging notice  
The battery may not begin charging immediately under the following  
conditions:  
The battery is extremely hot or cold (if the battery is extremely hot, it  
might not charge at all). To ensure the battery charges to its full capacity,  
you should charge it at room temperature of between 5° to 35°C (41° to  
95°F).  
The battery is nearly completely discharged. In this instance you should  
leave the AC adaptor connected for a few minutes and the battery  
should begin charging.  
The Battery indicator may show a rapid decrease in battery operating time  
when you try to charge a battery under the following conditions:  
The battery has not been used for a long time.  
The battery has completely discharged and been left in the computer for  
a long time.  
A cool battery is installed in a warm computer.  
In such cases you should follow the steps as detailed below:  
1. Fully discharge the battery by leaving it in the computer with the power  
on until the system automatically turns itself off.  
2. Connect the AC adaptor to the DC IN 19V jack of the computer, and to a  
wall outlet that is supplying power.  
3. Charge the battery until the Battery indicator glows green.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
6-6  
Power and Power-up Modes  
Repeat these steps two or three times until the battery recovers normal  
capacity.  
Monitoring battery capacity  
Remaining battery power can be monitored using the following methods.  
Clicking the battery icon on the task bar  
Via the Battery Status in the Windows Mobility Center window  
You should wait at least 16 seconds after turning on the computer  
before trying to monitor the remaining operating time. This is because  
the computer needs this time to check the battery's remaining capacity  
and then calculate the remaining operating time, based on this together  
with the current power consumption.  
Please be aware that the actual remaining operating time may differ  
slightly from the calculated time.  
With repeated discharges and recharges, the battery's capacity will  
gradually decrease. In view of this it will be noted that an often used,  
older battery will not operate for as long as a new battery even when  
both are fully charged.  
Maximizing battery operating time  
A battery's usefulness depends on how long it can supply power on a  
single charge, while how long the charge lasts in a battery depends on:  
Processor speed  
Screen brightness  
System Sleep Mode  
System Hibernation Mode  
Display power off period  
Hard disk drive power off period  
How often and for how long you use the hard disk drive, optical disc and  
floppy diskette drives.  
How much charge the battery contained to begin with.  
How you use optional devices, such as a PC Card, to which the battery  
supplies power.  
Whether you enable Sleep Mode, which can conserve battery power if  
you are frequently turning the computer off and on.  
Where you store your programs and data.  
Whether you close the display panel when you are not using the  
keyboard - closing the display saves power.  
The environmental temperature - operating time decreases at low  
temperatures.  
The condition of the battery terminals - you should always ensure the  
terminals stay clean by wiping them with a clean dry cloth before  
installing the battery pack.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
6-7  
   
Power and Power-up Modes  
Retaining data with power off  
When you turn off your computer with fully charged batteries, the batteries  
retain data for the following approximate time periods.  
Retention Time  
Battery type  
State and Retention Time  
Battery pack  
2 days for 12 cell, 1 day for 6 cell, 0.5  
day for 3 cell (sleep mode)  
20 days for 12 cell, 10 days for 6 cell,  
5 days for 3 cell (shut down mode)  
RTC battery  
30 days  
Extending battery life  
To maximize the life of your battery packs:  
At least once a month, disconnect the computer from a power source  
and operate it on battery power until the battery pack fully discharges.  
Before doing so, follow the steps as detailed below.  
1. Turn off the computer's power.  
2. Disconnect the AC adaptor and turn on the computer's power - if it  
does not turn on then go to Step 4.  
3. Operate the computer on battery power for five minutes. If you find  
that the battery pack has at least five minutes of operating time,  
continue operating until the battery pack is fully discharged,  
however, if the Battery indicator flashes or there is some other  
warning to indicate a low battery condition, go to Step 4.  
4. Connect the AC adaptor to the DC IN 19V jack of the computer, and  
to a wall outlet that is supplying power. The DC IN indicator should  
glow white, and the Battery indicator should glow amber to indicate  
that the battery pack is being charged, however, in the event that  
DC IN indicator does not glow this indicates that power is not being  
supplied - check the connections for the AC adaptor and the power  
cord.  
5. Charge the battery pack until the Battery indicator glows green.  
If you have extra battery packs, rotate their use.  
If you will not be using the system for an extended period, for example  
for more than one month, remove the battery pack from the computer.  
Disconnect the AC adaptor when the battery is fully charged -  
overcharging will make the battery hot and can shorten its operating life.  
If you are not going to use the computer for more than eight hours,  
disconnect the AC adaptor.  
Store spare battery packs in a cool dry place out of direct sunlight.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
6-8  
 
Power and Power-up Modes  
Replacing the battery pack  
Please be aware that the battery pack is classified as a consumable item.  
The operating life of the battery pack will gradually reduce through  
repeated charging and discharging, and will need to be replaced when it  
reaches the end of its operating life. In addition to this, you might also  
replace a discharged battery pack with a charged spare when you are  
operating your computer away from an AC power source for an extended  
period of time.  
This section explains how to remove and install the battery pack, and  
begins with the removal process which is detailed through the following  
steps.  
Do not remove the battery pack while the computer is in Sleep Mode.  
Data is stored in RAM, so if the computer loses power it will be lost.  
In Hibernation Mode, data will be lost if you remove the battery pack or  
disconnect the AC adaptor before the save is completed. Wait for the  
Hard Disk Drive indicator to go out.  
Do not touch the battery release latch while holding the computer or the  
battery pack might fall out due to the unintentional release of the  
battery release latch and cause injuries.  
To remove a discharged battery, follow the steps as detailed below:  
1. Save your work.  
2. Turn the computer's power off - ensure that the Power indicator is off.  
3. Remove all cables and peripherals that are connected to the computer.  
4. Close the display panel and turn the computer upside down.  
5. Slide the battery safety lock towards the release (  
the battery release latch movable.  
) position to make  
Figure 6-1 Releasing the battery pack (1)  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
6-9  
   
Power and Power-up Modes  
6. Slide and hold the battery release latch (1) to disengage the battery  
pack and then remove it from the computer (2).  
2
1
Figure 6-2 Releasing the battery pack (2)  
To install a battery, follow the steps as detailed below:  
1. Insert the battery pack as far as it will go into the computer (1).  
2. Ensure that the battery pack is securely in place and the battery safety  
lock (2) is in its position.  
1
2
Figure 6-3 Securing the battery pack  
3. Turn your computer over.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
6-10  
Power and Power-up Modes  
TOSHIBA Password Utility  
The TOSHIBA Supervisor Password Utility allows you to maintain an  
additional level of security and provides two levels of password security:  
User and Supervisor.  
Passwords set in TOSHIBA Supervisor Password Utility are different from  
®
the Windows login password.  
User Password  
To start the utility, point to or click the following items:  
Launch TOSHIBA Assist J SECURE J User Password  
Registered  
Click to register a password of up to 8 characters. After a password is  
set, you will be prompted to enter it when you start the computer.  
Not Registered  
Click to delete a registered password. Before you can delete a  
password, you must first enter the current password correctly.  
Owner String (text box)  
You can use this box to associate text with the password. After you  
enter text, click Apply or OK, then, each time the computer is switched  
on, this text will be displayed along with the prompt for the password.  
Supervisor password  
If you set a supervisor password, some functions will be restricted when a  
user logs on with the user password. To set a supervisor password:  
TOSHIBA Assist J SECURE J Supervisor password  
This utility lets you do the following:  
Register or delete the supervisor password.  
Specify restrictions for general users.  
Starting the computer by password  
If you have already registered a password, there is one way to start the  
computer:  
Enter the password manually.  
The password is necessary only if the computer was shut down in boot  
mode, not in Hibernation or Sleep mode.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
6-11  
     
Power and Power-up Modes  
To enter a password manually, follow these steps:  
1. Turn on the power as described in Chapter 3, Getting Started. The  
following message will appear in the LCD:  
Enter Password [xxxxxxxx]  
At this point, the hotkeys Fn + F1 to F9 do not work. They will function after  
you enter the password.  
2. Enter the Password.  
3. Press Enter.  
If you enter the password incorrectly three consecutive times, the  
computer shuts down. You must turn on the computer again and re-enter  
the password.  
Power-up modes  
The computer has three power-up modes:  
Hibernation (saves data in memory to the hard disk)  
Sleep (power remains on, maintaining the data in memory, but the CPU  
and all other devices effectively enter a 'sleep' mode)  
Boot (does not save data in memory)  
Refer also to the section Turning off the power in Chapter 3, Getting  
Started.  
Windows utilities  
You can configure various settings associated with both Sleep Mode and  
Hibernation Mode within the Power Options. To access it, click Start →  
Control Panel System and Security Power Options.  
Hot keys  
You can use the FN + F3 hot key to enter Sleep Mode or FN + F4 to enter  
Hibernation Mode - please refer to Chapter 5, The Keyboard for further  
details.  
Panel power on/off  
You can set up your computer so that power is turned off automatically  
when you close the display panel, and turned on again when you open it.  
Please note that this function is only available for Sleep Mode or  
Hibernation Mode, not for Shut Down Mode.  
If the panel power off function is enabled and you manually shut down  
Windows, do not close the computer's display panel until the shut down  
process has been completed.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
6-12  
   
Power and Power-up Modes  
System auto off  
This feature turns the system off automatically if it is not used for a set  
duration. The system shuts down in sleep mode or hibernation mode.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
6-13  
 
Chapter 7  
HW Setup and Passwords  
This chapter explains how to use TOSHIBA HW Setup program to  
configure your computer and how to set passwords.  
HW Setup  
TOSHIBA HW Setup allows you to configure settings for General,  
Password, Display, Boot Priority, Keyboard, USB, LAN.  
If the supervisor password is set, access to the TOSHIBA HW Setup  
program can be prevented when the user password is used to log on to the  
computer.  
Accessing HW Setup  
Click on Start All Programs TOSHIBA Utilities and click  
HWSetup.  
HW Setup Window  
The HW Setup window contains the following tabs: General, Password,  
Display, Boot Priority, Keyboard, LAN, USB.  
OK  
Accepts your changes and closes the HW Setup  
window.  
Cancel  
Apply  
Closes the window without accepting your  
changes.  
Accepts all your changes without closing the HW  
Setup window.  
General  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7-1  
               
HW Setup and Passwords  
This window displays the BIOS version and contains two buttons:  
Default  
Return all HW Setup values to the factory  
settings.  
About  
Display the HW Setup version.  
Setup  
This field displays BIOS Version and date.  
When finish BIOS update, please restart your computer and press F2 into  
BIOS setup manual and load BIOS default one time.  
Password  
User Password  
This option allows you to set or reset the user password for power on.  
Not Registered  
Registered  
Changes or remove the password. (Default)  
Sets the password. A dialogue box will appear to  
allow you to set the password.  
To enter a user password:  
1. Select Registered to display the following prompt:  
Enter Password:  
Enter a password of up to 8 characters. The character string you enter  
is displayed as a string of asterisks. For example, if you enter a  
password consisting of four characters, the display is shown as:  
Enter Password: ****  
2. Click the OK button. The following message appears, allowing you to  
verify the password.  
Verify Password:  
3. If character strings match, the password is registered click OK button. If  
they do not match, the following message appears. You must repeat  
from step 1.  
Entry Error!!!  
To delete a user password:  
1. Select Not Registered to display the following prompt:  
Enter Password:  
2. Enter the currently registered password. The character string you enter  
is displayed as a string of asterisks.  
Enter Password: ****  
3. Click the OK button. If the character string you enter matches the  
registered password, the password option is reset and the display  
changes to:  
Not registered  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7-2  
HW Setup and Passwords  
If they do not match, the following message appears. You must repeat step 1.  
Incorrect Password!!!  
If you enter the password incorrectly three times in a row, the computer will  
shut down.  
You will not be able to access the password option in the HW Setup. In this  
case you must turn the power off and back on in order to retry the  
procedure.  
4. Follow the same procedures described in the earlier section, How to set  
the password, to set a new user password.  
Display  
This tab allows you to customize your computer’s display settings for either  
the internal LCD screen or for an external monitor.  
Power On Display  
Allows you to set the display to be used when the computer is booted up.  
Auto-Selected  
If any external display is connected, the power on  
display will be in "external display only" mode.  
Otherwise it will be in "LCD only" mode.  
System LCD only  
Irrespective of external display connection, the  
power on display will be in integrated "LCD only"  
mode (Default).  
Boot Priority  
Boot Priority Options  
This option sets the priority for booting the computer. You can change the  
boot priority from the device list.  
Button Setting  
Function Button  
This feature allows you to set conditions for the Power Button and/or the  
other buttons.  
Enabled  
Disabled  
Enables the function button  
Disables the function button  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7-3  
 
HW Setup and Passwords  
Keyboard  
Wake-up on Keyboard  
When this feature is enabled and the computer is in Sleep mode, you can  
turn on the computer by pressing any key. It is effective only for the internal  
keyboard and only when the computer is in Sleep mode.  
Enabled  
Disabled  
Enables the Wake-up on Keyboard feature.  
Disables the Wake-up on Keyboard function  
(Default).  
USB  
Legacy USB Support  
Use this option to enable or disable USB Legacy Emulation. If your  
operating system does not support USB, you can still use a USB mouse  
and keyboard by setting the USB Legacy Emulation item to enabled.  
Enabled  
Disabled  
Enables the USB Legacy Emulation. (Default)  
Disables the USB Legacy Emulation.  
LAN  
Wake-up on LAN  
This feature lets the computer’s power be turned on from shutdown when it  
receives a wake-up packet ( Magic packet ) from the LAN.  
For activating Wake-up on LAN from sleep or hibernation, you must check  
the "Allow the device to wake the computer" check box within the LAN  
Device properties. ( This feature does not affect the Wake-up on LAN from  
sleep or hibernation. )  
Enabled  
Disabled  
Enables Wake-up on LAN from shutdown.  
Disables Wake-up on LAN. from shutdown.  
(Default)  
The Wake-up on LAN function consumes power even when the system is  
off. Leave the AC adaptor connected while using this feature.  
Do not install or remove an optional memory module while Wake-up on  
LAN is enabled.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7-4  
HW Setup and Passwords  
Built-in LAN  
This feature enables or disables the Built-in LAN.  
Enabled  
Disabled  
Enables Built-in LAN function (Default).  
Disables Built-in LAN function.  
Wireless Communication Switch  
This feature enables or disables the Wireless Communication Switch.  
ON  
Enable Wireless Communication Switch function.  
Disable Wireless Communication Switch function.  
OFF  
SATA  
eSATA  
This feature allows you to set conditions of eSATA.  
Enabled  
Disabled  
Enables the eSATA port. (Default)  
Disables the eSATA port in order to save power.  
SATA Interface setting  
This feature allows you to set SATA interface setting.  
Performance  
Let HDD/SSD work with maximum performance.  
(Default)  
Battery life  
Let HDD/SSD work with battery life mode. If this  
setting is selected, this causes performance  
down.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7-5  
Chapter 8  
Optional Devices  
Optional devices can expand the computer's capabilities and its versatility.  
This chapter describes the connection or installation of the following  
devices:  
To connect optional devices (such as USB device or External monitor) to  
the computer, be sure to check the shape and orientation of the connector  
before connecting.  
Cards/memory  
PC Card  
Bridge media slot  
Secure Digital (SD) Card (SD memory card, SDHC memory card,  
miniSD Card, microSD Card)  
Memory Stick (Memory Stick, Memory Stick PRO)  
MultiMediaCard  
Memory expansion  
Power devices  
Battery packs  
Universal AC Adaptor  
Battery Charger  
Peripheral devices  
Hard disk drive pack  
USB floppy diskette drive  
eSATA  
External monitor  
HDMI  
Other  
Security lock  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8-1  
     
Optional Devices  
PC Card  
The computer is equipped with a single PC Card slot into which any Type II  
PC Card/ CardBus device that meets industry standards, either  
manufactured by TOSHIBA or another vendor, can be installed. The slot  
supports hot plug connection and utilizes the PCI interface that supports  
the reading and writing of data at a theoretical maximum rate of 132 Mbps.  
Inserting a PC Card  
The Windows hot-install feature allows you to insert PC Cards while the  
computer is turned on.  
Do not insert a PC Card while the computer is in Sleep Mode or  
Hibernation Mode as you may find that some cards do not work  
properly.  
To insert a PC Card, follow the steps as detailed below:  
1. Press the PC Card eject button to partially extend it out of the computer.  
2. Press the extended PC Card eject button in order to eject the Dummy  
card partially out of the computer.  
3. Grasp the Dummy card and draw it.  
4. Insert the PC Card into the PC Card slot on the side of the computer.  
5. Press the PC Card gently to ensure a firm connection is made.  
Figure 8-1 Inserting the PC Card  
6. After inserting the PC Card you should refer to its documentation and  
also check the configuration in Windows in order to ensure that it is  
correct.  
User’s Manual  
8-2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Optional Devices  
Removing a PC Card  
To remove a PC Card, follow the steps as detailed below.  
1. Open the Safely Remove Hardware and Eject Media icon on the  
Windows Task Bar.  
2. Point to PC Card device and click the left Touch Pad control button.  
3. Press the PC Card eject button to partially extend it out of the computer.  
If the PC Card is not inserted all the way into the computer, the eject button  
may not cause it to pop out sufficiently to allows it to be grasped. In this  
instance, simply push the PC Card firmly back into the computer and then  
press the eject button again.  
4. Press the extended eject button in order to eject the PC Card partially  
out of the computer.  
5. Grasp the PC Card and remove it.  
Figure 8-2 Removing the PC Card  
6. Re-insert the Dummy card into the PC Card slot.  
When you do not use a PC Card, please be sure to insert a Dummy card.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8-3  
 
Optional Devices  
Bridge media slot  
The computer is equipped with a Bridge media slot that can accommodate  
some kinds of memory media with various memory capacities so that you  
can easily transfer data from devices, such as digital cameras and  
Personal Digital Assistants.  
Keep foreign objects out of the Bridge media slot. Never allow metal  
objects, such as screws, staples and paper clips, to enter the computer  
or Keyboard. Foreign metal objects can create a short circuit, which  
can cause computer damage and fire, possibly resulting in serious  
injury.  
This Bridge media slot supports the following memory media:  
Secure Digital (SD) Card (SD memory card, SDHC memory card,  
miniSD Card, microSD Card)  
Memory Stick (Memory Stick, Memory Stick PRO)  
MultiMediaCard (MMC)  
Please note that an adaptor is required to use miniSD/microSD Card.  
Please note that not all memory media have been tested and verified to  
work correctly. Therefore, it is not possible to guarantee that all  
memory media will operate properly.  
The slot does not support cF or SmartMedia cards, or Magic Gate  
functions.  
MultiMediaCard  
(MMC)  
microSD card  
and adaptor  
Memory Stick  
Secure Digital  
(SD) Card  
Figure 8-3 Examples of memory media  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8-4  
   
Optional Devices  
Memory media  
This section provides the important safety precautions in order to handle  
your memory media.  
Points to note about the SD/SDHC memory card  
SD/SDHC memory cards comply with SDMI (Secure Digital Music  
Initiative), which is a technology adopted to prevent unlawful copy or  
playback of digital music. For this reason, you cannot copy or playback  
protected material on another computer or other device, and you may not  
reproduce any copyrighted material except for your personal enjoyment.  
Below is a simple explanation for distinguishing SD memory cards from  
SDHC memory cards.  
SD and SDHC memory cards appear the same externally.  
The logo on SD and SDHC memory cards is different, so pay careful  
attention to the logo when purchasing.  
The SD memory card logo is (  
).  
The SDHC memory card logo is (  
).  
The maximum capacity of SD memory cards is 2GB. The maximum  
capacity of SDHC memory cards is 32GB.  
Card Type  
Capacities  
SD  
8MB, 16MB, 32MB, 64MB, 128MB, 256MB,  
512MB, 1GB, 2GB  
SDHC  
4GB, 8GB, 16GB, 32GB  
Memory media format  
New media cards are formatted according to specific standards. If you wish  
to reformat a media card, be sure to do so with a device that uses media  
cards.  
Formatting an SD/SDHC memory card  
SD/SDHC memory cards are sold already formatted in conformity to  
specific standards. If you reformat an SD/SDHC memory card, be sure to  
reformat it with a device such as digital camera or digital audio player that  
uses the SD/SDHC memory cards, not with the format command provided  
within Windows.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8-5  
Optional Devices  
Additional memory module  
You can install additional memory into the computer in order to increase the  
amount of system memory that is available. This section describes how to  
install and remove optional memory modules.  
You should place a mat beneath the computer in order to prevent the  
computer's lid from becoming scratched or damaged when you are  
installing/replacing the memory module. In this instance you should  
avoid mats that are made of materials that hold or generate static  
electricity.  
When installing or removing a memory module, you must ensure that  
you do not touch any other internal areas of the computer.  
Insert the two memory modules into Slot A and Slot B respectively. The  
computer will operate in dual channel mode.  
You can access the inserted memory modules efficiently in dual  
channel.  
Use only memory modules approved by TOSHIBA.  
Do not try to install or remove a memory module under the following  
conditions.  
a. The computer is turned on.  
b. The computer was shut down in either Sleep or Hibernation Mode.  
c. Wake-up on LAN is enabled.  
Be careful not to let screws or other foreign matter fall into the  
computer. It could cause malfunction or electric shock.  
Additional memory module is a precision electronic component that  
may be fatally damaged by static electricity. Since the human body can  
carry static electricity, it is important that you discharge yourself before  
touching or installing any additional memory modules. To discharge  
your body’s static electricity, simply touch any metal close to you with  
bare hands.  
Point to note about memory module error  
If you install a memory module that is not compatible with the computer, the  
Power indicator will flash in the following ways:  
If there is an error in only Slot A or no memory module is inserted in Slot  
A: repeatedly flashes amber twice, then green.  
If there is an error in Slot B: repeatedly flashes amber, then green twice.  
If there are errors in both Slot A and Slot B: repeatedly flashes amber  
twice, then green twice.  
In all instances you should shut down the computer and remove the  
incompatible module(s).  
Use a # 0-point Phillips screwdriver to remove and fasten the screws - the  
use of an incorrect screwdriver can damage the screw heads.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8-6  
   
Optional Devices  
Installing a memory module  
The computer contains slots for two memory modules, one positioned  
immediately over the other - the procedures are the same for installing  
either module.  
1. Shut down the computer - make sure the Power indicator is off (refer to  
the Turning off the power section in Chapter 3, Getting Started if  
required).  
2. Remove the AC adaptor and all cables and peripherals connected to  
the computer.  
3. Turn the computer upside down and remove the memory module cover.  
1
1
2
2
2
3
4
3
1. Memory module cover  
2. Screw  
3. Slot B  
4. Slot A  
Figure 8-4 Removing the memory module cover  
4. Align the notch of the memory module with that of the memory module  
slot and gently insert the module into the slot at about a 45 degree  
angle before holding it down until the latches on either side snap into  
place.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8-7  
 
Optional Devices  
Align the grooves along the edges of the memory module with the  
locking tabs on the connector and insert the memory module into the  
connector firmly. If you find it difficult to install the memory module,  
gently prise the locking tabs outwards using the tip of your finger.  
Please also ensure that you hold the memory module along its left and  
right hand edges - the edges with the grooves in.  
Never allow metal objects, such as screws, staples and paper clips, to  
enter the computer or keyboard. Foreign metal objects can create a  
short circuit, which can cause computer damage and fire, possibly  
resulting in serious injury.  
Do not touch the connectors on the memory module or on the  
computer. Debris on the connectors may cause memory access  
problems.  
5. Seat the memory module cover in place and secure it with one screw.  
Take care to ensure that the memory module cover is firmly closed.  
Figure 8-5 Seating the memory module cover  
6. Install the battery pack - refer to Replacing the battery pack section in  
Chapter 6, Power and Power-up Modes, if required.  
7. Turn your computer over.  
8. Turn the computer on and make sure the added memory is recognized -  
to confirm it, Start Control Panel System and Security System  
icon.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8-8  
Removing a memory module  
To remove the memory module, follow the steps as detailed below:  
1. Set the computer to Boot Mode and turn its power off - make sure the  
Power indicator is off (refer to the Turning off the power section in  
Chapter 3, Getting Started if required).  
2. Remove the AC adaptor and all cables and peripherals connected to  
the computer.  
3. Turn the computer upside down and remove the battery pack (refer to  
Replacing the battery pack section in Chapter 6, Power and Power-up  
Modes, if required).  
4. Push the latches away from the module in order to release it.  
5. Grasp the memory module by its edges and remove it from the  
computer.  
If you use the computer for a long time, the memory modules and the  
circuits locating close to the memory modules will become hot. In this  
case, let them cool to room temperature before you replace them.Or  
you will get burnt if you touch any of them.  
Do not touch the connectors on the memory module or on the  
computer. Debris on the connectors may cause memory access  
problems.  
6. Seat the memory module cover in place and secure it with one screw.  
Take care to ensure that the memory module cover is firmly closed.  
7. Install the battery pack - refer to Replacing the battery pack section in  
Chapter 6, Power and Power-up Modes, if required.  
8. Turn your computer over.  
Battery Packs  
You can increase the portability of the computer with additional battery  
packs so that, if you're away from an AC power source and your battery  
runs low, you can replace it with a freshly-charged battery. Please refer to  
Chapter 6, Power and Power-up Modes for further information.  
Universal AC Adaptor  
If you frequently use your computer at more than one site, it may be  
convenient to purchase an additional AC adaptor to be kept at each site in  
order to remove the need to always carry the adaptor with you.  
Battery Charger  
The battery charger provides a convenient way to charge up to two Lithium  
Ion battery packs without requiring the use of your computer.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8-9  
           
Optional Devices  
USB floppy diskette drive  
The USB floppy diskette drive accommodates either a 1.44MB or 720KB a  
3 2/1" floppy diskette and connects to one of the computer's USB ports.  
The USB floppy diskette drive is available only as an option.  
a
b
c
d
1. USB connector  
2. Disk-In-Use Indicator  
3. Floppy diskette slot  
4. Eject button  
Figure 8-6 USB floppy diskette drive  
USB connector  
Insert this connector into one of the free USB  
ports of your computer.  
Disk-In-Use Indicator This indicator glows when the floppy diskette is  
being accessed.  
Floppy diskette slot  
Eject button  
Insert a floppy diskette into this slot.  
When a floppy diskette is fully seated in the drive,  
the eject button will pop out. In order to remove  
the diskette, push the eject button in order to  
cause it to partially pop out of the drive and then  
remove it.  
Check the Disk-In-Use indicator when you use the floppy diskette drive.  
Do not press the eject button or turn off the computer while the light is  
glowing. Doing so could destroy data and damage the floppy diskette or  
the drive.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8-10  
   
Optional Devices  
In use, the following should be noted regarding the operation of the USB  
floppy diskette drive:  
The drive should be placed on a flat, horizontal surface.  
Do not set the drive on an incline greater than 20° while it is operating.  
Do not place anything on top of the drive.  
Using the USB floppy diskette drive  
The USB floppy diskette drive accommodates either a 1.44MB or 720KB  
floppy diskette and connects to one of the computer's USB ports.  
Connecting the USB floppy diskette drive  
To connect the drive, plug the floppy diskette drive's USB connector into  
one of the computer's free USB ports.  
Make sure the connector is right side up and properly aligned with the  
socket. Do not try to force the connection; doing so can damage the  
connecting pins.  
Figure 8-7 Connecting the USB floppy diskette drive  
If you connect the USB floppy diskette drive after the computer has already  
been turned on, it will take about ten seconds for it to be recognized by the  
computer. Do not attempt to disconnect and reconnect the drive before this  
period has elapsed.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8-11  
 
Optional Devices  
Disconnecting the USB floppy diskette drive  
When you have finished using the USB floppy diskette drive, you can follow  
the procedures below in order to disconnect it:  
1. Wait for the Disk-In-Use Indicator light to go out to make sure all floppy  
diskette activity has stopped.  
If you disconnect the floppy diskette drive or turn off the power while the  
computer is accessing the drive you may lose data or damage the floppy  
diskette or the drive.  
2. Click the Safely Remove Hardware and Eject Media icon on the Task  
Bar.  
3. Click the USB floppy diskette drive device that you want to remove.  
4. Carefully pull the floppy diskette drive's USB connector out from within  
the computer's USB port.  
eSATA (External Serial ATA)  
An device corresponding to eSATA function can be connected to the  
eSATA/USB combo port on the computer.  
Connecting the eSATA device  
To connect an eSATA device, follow the steps as detailed below:  
1. Connect an eSATA cable to the eSATA/USB combo port.  
Make sure the connector is properly aligned with the socket.Do not try to  
force the connection, doing so can damage the connecting pins.  
Figure 8-8 Connecting an eSATA cable to the eSATA/USB combo port  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8-12  
 
Optional Devices  
A connected eSATA device may not be recognized if it is connected to  
the computer's eSATA/USB combo port while the computer is in Sleep  
Mode or Hibernation Mode. If this occurs, disconnect the eSATA device  
and then reconnect the device while the computer is turned on.  
If you connect an eSATA device after the computer has already been  
turned on, it will take about ten seconds for it to be recognized by the  
computer.  
Do not attempt to disconnect and reconnect the drive before this period  
has elapsed.  
Disconnecting an eSATA device  
When you have finished using an eSATA device, you can follow the  
procedures below in order to disconnect it:  
1. Wait for the indicator light of an eSATA device to go out to make sure all  
activity has stopped.  
If you disconnect an eSATA device or turn off the power while the  
computer is accessing the drive you may lose data or damage an eSATA  
device or the drive.  
2. Click the Safely Remove Hardware and Eject Media icon on the  
Windows Taskbar.  
3. Click the eSATA device that you want to remove.  
4. Carefully pull the eSATA device's eSATA/USB combo connector out  
from within the computer's eSATA/USB combo port.  
External monitor  
An external analog monitor can be connected to the computer's external  
monitor port, with the computer supporting WUXGA video mode. In order to  
connect a monitor, follow the steps as detailed below:  
1. Turn the computer's power off.  
2. Connect the monitor cable to the external monitor port and tighten the  
screws on the left and right hand side of the connector as required.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8-13  
   
Optional Devices  
Figure 8-9 Connecting the monitor cable to the external monitor port  
3. Turn the external monitor’s power on.  
4. Turn the computer's power on.  
Some models are equipped with an external monitor port.  
When you turn on the power, the computer will automatically recognize the  
monitor and determine whether it is a color or monochrome device. If you  
have problems on getting an image displayed on the correct monitor, you  
should use the FN + F5 hot key to change the display settings (if you then  
disconnect the external monitor before you turn the computer's power off,  
be sure to press FN + F5 hot key again to switch to the internal display).  
Please refer to Chapter 5, The Keyboard, for further details on using hot  
keys to change the display setting.  
You can use the HW Setup to select between Auto-Selected and System  
LCD Only displays. Refer to Chapter 7, HW Setup and Passwords.  
If you have selected System LCD Only under the Display options of the HW  
Setup, the internal LCD will be active when you turn on the computer, even  
if the external monitor is connected. If Auto-Selected is selected, only the  
external monitor will be active.  
Do not disconnect the external monitor while in Sleep or Hibernation Mode.  
Turn off the computer before disconnecting the external monitor.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8-14  
Optional Devices  
Television via HDMI  
A television can be connected to the HDMI out port on the computer.  
To connect a television, follow the steps below.  
1. Turn the computer off.  
2. Use a video cable (not supplied) to connect the television to either the  
HDMI out port.  
3. Turn the television on.  
4. Turn the computer on.  
You can use the hotkeys Fn + F5 or use the TV-Out button to change the  
display device. Refer to Chapter 5, The Keyboard.  
If a television is connected to the computer, set the TV type in Display  
Properties. Follow the steps below, based on the configuration of your  
computer.  
As the port operation of all HDMI (High-Definition Multimedia Interface)  
monitors have not been confirmed, some HDMI monitors may not  
function properly.  
When you connect a television or external monitor to the HDMI port  
and the display output device is set to HDMI. When you unplug the  
HDMI cable and re-plug it in please wait at least 5 seconds before you  
replug the HDMI cable again.  
When you connect a television or external monitor to the HDMI port  
and you connect the television, external monitor or external sound  
device to another port. When you change the display output or  
Unplug/re-plug the HDMI cable. The sound output device and the  
display output device maybe changed automatically by the system.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8-15  
 
Optional Devices  
For Intel  
1. Click Start J Control Panel J Appearance and Personalization J  
Personalization J Display J Adjust screen resolution.  
2. Click the Advanced settings button. The Generic PnP Monitor and  
Mobile Intel® Arrandale Graphics Properties dialogue box opens.  
3. Click the Graphics Properties button.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8-16  
Optional Devices  
4. In the subsequent dialogue box, click Display J Multiple Displays and  
then set up your television and notebook displays.  
For ATI  
1. Click Start J All Programs J Catalyst Control Center J CCC.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8-17  
Optional Devices  
2. Click Graphics and select Desktop & Displays.  
3. Click the triangle icon on TV and select the display mode for TV.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8-18  
Optional Devices  
Security lock  
A security locks enable you to anchor your computer to a desk or other  
heavy object in order to help prevent unauthorized removal or theft. The  
computer has a security lock slot on its right side into which you can attach  
one end of the security cable, while the other end attaches to a desk or  
similar object. The methods used for attaching security cables differ from  
product to product. Please refer to the instructions for the product you are  
using for more information.  
Connecting the security lock  
In order to connect a security cable to the computer, follow the steps as  
detailed below:  
1. Turn the computer so its right hand side faces you.  
2. Align the security cable with the 'lock hole' and secure it in place.  
Figure 8-10 Security lock  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8-19  
   
Chapter 9  
Troubleshooting  
TOSHIBA have designed this computer for durability, however, should  
problems occur you are able to use the procedures detailed in this chapter  
to help determine the cause.  
All users should become familiar with this chapter as knowing what might  
go wrong can help prevent problems from occurring in the first place.  
Problem solving process  
Resolving problems will be much easier if you observe the following  
guidelines:  
Stop immediately when you recognize a problem exists as taking further  
action may result in data loss or damage, or you may destroy valuable  
problem-related information that can help solve the problem.  
Observe what is happening. Write down what the system is doing and  
what actions you performed immediately before the problem occurred.  
If you have a printer attached, print a copy of the screen using the  
computer's PRTSC key.  
Please also be aware that the questions and procedures described in this  
chapter are meant only as a guide, they are not definitive problem solving  
techniques. In reality many problems can be solved simply, but a few may  
require help from your reseller, dealer or service provider. If you find you  
need to consult others, be prepared to describe the problem in as much  
detail as possible.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
9-1  
       
Troubleshooting  
Preliminary checklist  
You should always consider the simplest solution first - the items detailed in  
this checklist are easy to fix and yet may cause what appears to be a  
serious problem:  
Make sure you turn on all peripheral devices before you turn on the  
computer - this includes your printer and any other external device you  
are using.  
Before you attach an external device you should first turn the computer  
off, then when you turn the computer back on again it will recognize the  
new device.  
Make sure all optional accessories are configured properly in the  
computer's setup program and that all required driver software has  
been loaded (please refer to the documentation included with the  
optional accessories for further information on its installation and  
configuration).  
Check all cables to ensure they are correctly and firmly attached to the  
computer - loose cables can cause signal errors.  
Inspect all connecting cables for loose wires and all connectors for  
loose pins.  
Check that your floppy diskette, CD, DVD or BD media is correctly  
loaded.  
Always try to make detailed notes of your observations and keep them in a  
permanent error log. This will help you to describe your problems to your  
reseller, dealer or service provider. In addition, if a problem recurs, the log  
you have made will help to identify the problem faster.  
Analyzing the problem  
Sometimes the computer will give you clues that can help you identify why  
it is malfunctioning. In view of this you should keep the following questions  
in mind:  
Which part of the computer is not operating properly - keyboard, hard  
disk drive, optical disc drive, display panel, touch pad, touch pad control  
buttons - as each device will produce different symptoms.  
Check the options within the operating system to ensure that its  
configuration is set properly.  
What appears on the display? Does it display any messages or random  
characters? If you have a printer attached, print a copy of the screen  
using the PRTSC key and, if possible, look up the messages in the  
documentation included with the computer, software or operating system.  
Check that all connecting cables are correctly and firmly attached as  
loose cables can cause erroneous or intermittent signals.  
Do any indicators light up? If so, which ones, what color are they and do  
they stay on or blink? Write down what you see.  
Do you hear any beeps? If so, how many, are they long or short, and  
are they high-pitched or low-pitched? In addition, is the computer  
making any unusual noises? Write down what you hear.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
9-2  
 
Troubleshooting  
Record your observations so you can describe them in detail to your  
reseller, dealer or service provider.  
Software The problems may be caused by your software or disk. If you  
cannot load a software package, the media may be damaged  
or the program might be corrupted. In these instances try  
loading another copy of the software if possible.  
If an error message appears while you are using a software  
package you should refer to the documentation supplied with  
it as this will usually include a problem-solving section or a  
summary of error messages.  
Next, you should check any error messages against the  
operating system documentation.  
Hardware If you cannot find a software problem, you should then check  
the setup and configuration of your hardware. First, run  
through the items in the preliminary checklist as described  
previously. Then, if you still cannot correct the problem, try to  
identify the source - the next section provides checklists for  
individual components and peripherals.  
Before using a peripheral device or application software that is not an  
authorized Toshiba part or product, make sure the device or software can  
be used with your computer. Use of incompatible devices may cause injury  
or may damage your computer.  
Hardware and system checklist  
This section discusses problems caused by your computer’s hardware or  
attached peripherals. Basic problems may occur in the following areas:  
System start-up  
Self test  
Power  
Password  
Keyboard  
Internal display panel  
Hard disk drive  
PC Card  
USB device  
eSATA device  
Memory expansion  
Recovery Discs  
Sound system  
External monitor  
Modem  
LAN  
SD/SDHC memory card,  
miniSD/microSD Card  
Memory Stick/Memory Stick PRO  
MultiMediaCard  
Pointing device  
Wireless LAN  
Bluetooth  
HDMI monitor output function  
Video Playback  
System start-up  
When the computer does not start properly, check the following items:  
Self test  
Power Sources  
Power-on Password  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
9-3  
     
Troubleshooting  
Self test  
While booting up the computer, self test is executed automatically and the  
following will be displayed:  
TOSHIBA Leading Innovation>>>  
This message remains on the screen for a few seconds.  
If the self test is successful, the computer tries to load the operating system  
according to how the Boot Priority option is set within the TOSHIBA HW  
Setup program.  
If any of the following conditions are present, the self test has failed:  
The computer stops and does not proceed to display information or  
messages except for the TOSHIBA logo.  
Random characters appear on the screen and the system does not  
function normally.  
The screen displays an error message.  
In these instances, turn off the computer, check all cable connections and  
then restart it. If the self test fails again, contact your reseller, dealer or  
service provider.  
Power  
When the computer is not plugged into an AC power outlet, the battery  
pack is the primary power source. However, your computer also has a  
number of other power resources, including an intelligent power supply and  
a Real Time Clock (RTC) battery, all of which are interrelated with any one  
having the ability to produce apparent power problems.  
This section provides checklists for AC power and the battery. If you cannot  
resolve a problem after following them, the cause may lie with another  
power related resource - in such an instance you should contact your  
reseller, dealer or service provider.  
Overheating power down  
If the processor's temperature reaches an unacceptably high level with  
either setting, the computer will automatically shut down to prevent any  
damage - in this instance all unsaved data in memory will be lost.  
Problem  
Procedure  
Computer shuts down Leave the computer off until the DC IN indicator  
and DC IN indicator  
stops blinking.  
blinks green  
It is recommended to leave the computer off until its interior reaches room  
temperature even though the DC IN indicator stops blinking.  
User’s Manual  
9-4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Troubleshooting  
and it still does not start, or if it starts but shuts  
down quickly, contact your reseller, dealer or  
service provider.  
Computer shuts down This indicates a problem with the heat dispersal  
and DC IN indicator is system - you should contact your reseller, dealer  
flashing green  
or service provider.  
AC power  
If you have trouble turning on the computer with the AC adaptor connected  
you should check the status of the DC IN indicator. Please refer to Chapter  
6, Power and Power-up Modes for further information.  
Problem  
Procedure  
AC adaptor doesn’t  
power the computer  
Check the connections to make sure that the  
power cord/adaptor is firmly connected to the  
(DC IN indicator does computer and a working power outlet.  
not glow green)  
the cord is frayed or damaged it should be  
replaced, while if the terminals are soiled, they  
should be cleaned with a clean cotton cloth.  
If the AC adaptor still does not power the  
computer, you should contact your reseller,  
dealer or service provider.  
Battery  
If you suspect a problem with the battery, you should check the status of  
the DC IN indicator as well as the Battery indicator. Please refer to Chapter  
6, Power and Power-up Modes for more information on these indicators,  
together with general battery operation.  
Problem  
Procedure  
Battery doesn’t power The battery may be discharged - connect the AC  
the computer adaptor to recharge the battery.  
Battery doesn’t charge If the battery is completely discharged, it will not  
when the AC adaptor  
is attached (Battery  
indicator does not  
glow amber).  
begin charging immediately, in these instances  
you should wait a few minutes before trying  
again. If the battery still does not charge, you  
should check that the power outlet to which the  
AC adaptor is connected is supplying power - this  
can be tested by plugging another appliance into  
it.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
9-5  
   
Troubleshooting  
Problem  
Procedure  
Check whether the battery is hot or cold to the  
touch - if so, it will not charge properly and should  
be allowed to reach room temperature before  
you try again.  
Unplug the AC adaptor and remove the battery to  
make sure its connecting terminals are clean - if  
necessary wipe them with a soft dry cloth lightly  
dipped in alcohol.  
Connect the AC adaptor and replace the battery,  
taking care to ensure that it is securely seated in  
the computer.  
Check the Battery indicator - if it does not glow,  
allow the computer to charge the battery for at  
least twenty minutes. If the Battery indicator  
starts to glow after this period, allow the battery  
to continue to charge for at least another twenty  
minutes before turning on the computer.  
However, if the indicator still does not glow, the  
battery may be at the end of its operating life and  
should be replaced. However, if you do not  
believe the battery is at the end of its operating  
life, you should speak to your reseller, dealer or  
service provider.  
Battery doesn’t power If you frequently recharge a partially charged  
the computer as long  
as expected  
battery, the battery might not charge to its full  
potential - in these instances you should fully  
discharge the battery and then attempt to charge  
it again.  
Check the Power saver option under Select a  
power plan in the Power Options.  
Real Time Clock  
Problem  
Procedure  
The following  
The RTC battery charge has become exhausted,  
message is displayed you should set the date and time in within the  
on the LCD:  
BIOS setup screen through the following steps:  
RTC battery is low or  
CMOS checksum is  
inconsistent. Press  
[F2] key to set  
1. Press [F2] key. BIOS setup will boot up.  
2. Press [F5]/[F6] to set the date in [System  
Date].  
3. Press [F5]/[F6] to set the time in [System  
Date/Time.  
Time].  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
9-6  
Troubleshooting  
Password  
Problem  
Procedure  
Cannot enter  
password  
Please refer to the TOSHIBA Password Utility  
section in Chapter 6, Power and Power-up  
Modes for further information.  
Keyboard  
Keyboard problems can be caused by the setup and configuration of the  
computer - please refer to Chapter 5, The Keyboard for further information.  
Problem  
Procedure  
Output to screen is  
garbled  
Please refer to your software's documentation to  
ensure that its is not remapping the keyboard in  
any way (remapping involves changing or  
reassigning the function of each key).  
If you are still unable to use the keyboard, you  
should contact your reseller, dealer or service  
provider.  
Internal display panel  
Apparent display panel problems may be related to the computer's setup  
and configuration - please refer to Chapter 7, HW Setup and Passwords,  
for further information.  
Problem  
Procedure  
No display  
Press the FN + F5 hot keys to adjust the display  
priority, and to make sure it is not set for output to  
an external monitor.  
Markings appear on the These marks may have come from contact with  
LCD screen.  
the keyboard or Touch Pad while the display has  
been closed. You should try to remove the marks  
by gently wiping the display panel with a clean  
dry cloth or, if this fails, with a good quality LCD  
screen cleaner. In this latter instance you should  
always follow the instructions with the screen  
cleaner and always ensure you let the LCD  
screen dry properly before closing it.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
9-7  
         
Troubleshooting  
Problem  
Procedure  
Problems above  
remain unresolved or  
other problems occur  
You should initially refer to the documentation  
supplied with you software to determine if it is  
this that is causing the problems. Alternatively  
you may wish to run the TOSHIBA PC  
Diagnostic Tool to check the general operation  
of the computer.  
If you are still unable to resolve the problem,  
contact your reseller, dealer or service provider.  
Display Power Saving Technology Display Power Saving Technology: Your  
model may include the Display Power Saving Technology Display Power  
Saving Technology feature that can save the computer's power  
consumption by optimizing picture contrast on the internal LCD. This  
feature can be used if the computer is:  
configured with Mobile Intel® HM55 Express Chipset model in graphic  
chip by Intel®*  
running under battery mode  
using the internal LCD display only  
The power and performance settings can be adjusted in the Intel®  
Graphics and Media Control Panel.  
To access this control panel go to  
Control Panel J Appearance and Personalizaion J Display J  
Change display settings J Advanced settings J Intel® Graphics and  
Media Control Panel J Graphics Properties J Power J Power  
Features J Graphics Power Plan Settings J select On battery J  
Display Power Saving Technology  
f you want to improve the picture quality under the conditions mentioned  
above, adjust the setting towards Maximum Quality or disable this feature.  
*Please visit your region's web site or refer to the catalog for the  
configuration details of the model that you have purchased.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
9-8  
Troubleshooting  
Solid State Drive  
Problem  
Procedure  
Computer does not  
boot from hard disk  
drive  
Check to see whether that is a floppy diskette in  
the floppy diskette drive or a CD-ROM/DVDROM  
in the optical disc drive - if so remove it and try to  
start the computer again.  
If this has no effect, check the Boot Priority  
setting within the TOSHIBA HW Setup utility -  
please refer to the Boot Priority section in  
Chapter 7, HW Setup and Passwords for further  
information.  
Please refer to your operating system  
documentation in order to determine whether  
there is a problem with any of the operating  
system files or settings.  
Hard disk drive  
Problem  
Procedure  
Computer does not  
boot from hard disk  
drive  
Check to see whether that is a floppy diskette in  
the floppy diskette drive or a CD-ROM/DVD-  
ROM in the optical disc drive - if so remove it and  
try to start the computer again.  
If this has no effect, check the Boot Priority  
setting within the TOSHIBA HW Setup utility -  
please refer to the Boot Priority section in  
Chapter 7, HW Setup and Passwords for further  
information.  
Please refer to your operating system  
documentation in order to determine whether  
there is a problem with any of the operating  
system files or settings.  
Slow performance  
The files on the hard disk drive may be  
fragmented - in this instance you should run the  
disk Defragmentation utility to check the  
condition of your files and the hard disk drive.  
Please refer to the operating system's  
documentation or online Help File for further  
information on operating and using the  
Defragmentation utility.  
As a last resort you should reformat the hard disk  
drive and then reload the operating system and  
all other files and data. If you are still unable to  
resolve the problem, contact your reseller, dealer  
or service provider.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
9-9  
   
Troubleshooting  
DVD Super Multi drive  
For further information, please refer to Chapter 4, Operating Basics.  
Problem  
Procedure  
Make sure the drive's disc tray is securely closed -  
You cannot access a  
CD/DVD/BD in the drive press it gently into the computer until it clicks into  
place.  
Open the drive's disc tray and ensure the CD or  
DVD is properly seated - it should lie flat with the  
label facing upwards.  
A foreign object in the drive's disc slot could  
block laser light from reading the CD or DVD -  
remove any foreign objects or obstructions that  
may be present.  
Check whether the CD or DVD is dirty - if it is,  
wipe it with a clean cloth lightly dipped in water or  
a neutral cleaner. Please refer to the Media care  
section in Chapter 4 for further details on  
cleaning the media.  
Some CD/DVD/BDs  
run correctly, but  
others do not  
The computer's software or hardware  
configuration may be causing a problem. Ensure  
that these configurations match the requirements  
of the CD/DVD/BD media (refer to the CD's or  
DVD's documentation if available).  
Check the type of CD or DVD media that you are  
using - the drive supports the following:  
DVD:  
CD:  
DVD-ROM, DVD-Video  
CD-DA, CD-Text, Photo CDTM  
(single/multi-session), CD-ROM Mode  
1, Mode 2, CD-ROM XA Mode 2  
(Form1, Form2), Enhanced CD (CD-  
EXTRA), Addressing Method 2  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
9-10  
Troubleshooting  
BD writer drive/BD Combo drive  
For further information, please refer to Chapter 4, Operating Basics.  
Problem  
Procedure  
You cannot access a  
CD/DVD/BDs in the  
drive  
Make sure the drive's disc tray is securely closed -  
press it gently into the computer until it clicks into  
place.  
Open the drive's disc tray and ensure the CD,  
DVD or BD is properly seated - it should lie flat  
with the label facing upwards.  
A foreign object in the drive's disc slot could  
block laser light from reading the CD, DVD or BD  
- remove any foreign objects or obstructions that  
may be present.  
Check whether the CD, DVD or BD is dirty - if it  
is, wipe it with a clean cloth lightly dipped in water  
or a neutral cleaner. Please refer to the Media  
care section in Chapter 4 for further details on  
cleaning the media.  
Some CD/DVD/BDs run The computer's software or hardware  
correctly, but others do configuration may be causing a problem. Ensure  
not  
that these configurations match the requirements  
of the CD/DVD/BDs media (refer to the CD's,  
DVD's or BD's documentation if available).  
Check the type of CD, DVD or BD media that you  
are using - the drive supports the following:  
BD:  
BD-ROM  
DVD:  
CD:  
DVD-ROM, DVD-Video  
CD-DA, CD-Text, Photo CDTM  
(single/multi-session), CD-ROM Mode  
1, Mode 2, CD-ROM XA Mode 2  
(Form1, Form2), Enhanced CD (CD-  
EXTRA), Addressing Method 2  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
9-11  
Troubleshooting  
USB floppy diskette drive  
The USB floppy diskette drive is available only as an option.  
For further information, please refer to Chapter 4, Operating Basics.  
Problem Procedure  
Drive does not operate Check the connection between the computer and  
the drive to ensure that it is properly attached.  
Some programs run  
The computer's software or hardware  
correctly but others do configuration may be causing a problem - ensure  
not  
that these configurations match your  
requirements (refer to any relevant  
documentation, for example that supplied with  
any software in use, for further information).  
You cannot access the Try another floppy diskette in the drive - if you are  
external floppy  
diskette drive  
able to access this disk then it indicates the  
original disk and not the drive is probably causing  
the problem.  
If you are still unable to resolve the problem,  
contact your reseller, dealer or service provider.  
PC Card  
For further information, please refer to Chapter 8, Optional Devices.  
Problem  
Procedure  
PC Card error occurs  
Remove the PC Card from the computer and  
then re-insert it in order to ensure it is firmly  
connected.  
In the event that the PC Card is attached to an  
external peripheral device, ensure that this  
connection is properly made.  
If the problem persists, then you should refer to  
the documentation supplied with your PC Card  
for further information.  
If you are still unable to resolve the problem,  
contact your reseller, dealer or service provider.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
9-12  
       
Troubleshooting  
SD/SDHC memory card, miniSD/microSD Card  
For further information, please refer to Chapter 8, Optional Devices.  
Problem  
Procedure  
SD/SDHC memory  
Remove the SD/SDHC memory card,  
card, miniSD/microSD miniSD/microSD Card from the computer and  
Card error occurs  
then reinsert it in order to ensure it is firmly  
connected.  
If the problem persists, then you should refer to  
the documentation supplied with your SD/SDHC  
memory card, miniSD/microSD Card for further  
information.  
You cannot write to an Remove the SD/SDHC memory card from the  
SD/SDHC memory  
card  
computer and check to ensure that it is not write  
protected.  
You cannot read a file Check to ensure the required file is actually on  
the SD/SDHC memory card, miniSD/microSD  
Card that is inserted into the computer.  
If you are still unable to resolve the problem,  
contact your reseller, dealer or service provider.  
Memory Stick/Memory Stick PRO  
For further information, please refer to Chapter 8, Optional Devices.  
Problem  
Procedure  
Memory Stick/Memory Remove the Memory Stick/Memory Stick PRO  
Stick PRO error  
occurs  
from the computer and then reinsert it in order to  
ensure it is firmly connected.  
If the problem persists, then you should refer to  
the documentation supplied with your Memory  
Stick/Memory Stick PRO for further information.  
You cannot write to an Remove the Memory Stick/Memory Stick PRO  
Memory Stick/Memory from the computer and check to ensure that it is  
Stick PRO  
not write protected.  
You cannot read a file Check to ensure the required file is actually on  
the Memory Stick/Memory Stick PRO that is  
inserted into the computer.  
If you are still unable to resolve the problem,  
contact your reseller, dealer or service provider.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
9-13  
     
Troubleshooting  
MultiMediaCard  
For further information, please refer to Chapter 8, Optional Devices.  
Problem  
Procedure  
MultiMediaCard error  
occurs  
Remove the MultiMediaCard from the computer  
and then reinsert it in order to ensure it is firmly  
connected.  
If the problem persists, then you should refer to  
the documentation supplied with your  
MultiMediaCard for further information.  
You cannot read a file Check to ensure the required file is actually on  
the MultiMediaCard that is inserted into the  
computer.  
If you are still unable to resolve the problem,  
contact your reseller, dealer or service provider.  
Pointing device  
If you are using a USB mouse, you should also refer to both the USB  
device section in this chapter, and the documentation supplied with your  
mouse.  
Touch Pad  
Problem  
Procedure  
On-screen pointer  
does not respond to  
pointing device  
operation  
In this instance the system might be busy - Try  
moving the mouse again after waiting a short  
while.  
Double-tapping does  
not work  
In this instance, you should initially try changing  
the double-click speed setting within the Mouse  
Control utility.  
1. To access this utility, click Start Control  
Panel Hardware and Sound Mouse  
icon.  
2. Within the Mouse Properties window, click  
the Buttons tab.  
3. Set the double-click speed as required and  
click OK.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
9-14  
       
Troubleshooting  
Problem  
Procedure  
The mouse pointer  
moves too fast or too  
slow  
In this instance, you should initially try changing  
the speed setting within the Mouse Control utility.  
1. To access this utility, click Start Control  
Panel Hardware and Sound Mouse  
icon.  
2. Within the Mouse Properties window, click  
the Pointer Options tab.  
3. Set the pointer speed as required and click  
OK.  
If you are still unable to resolve the problem,  
contact your reseller, dealer or service provider.  
The reaction of Touch Adjust the touch Sensitivity.  
pad is either too  
1. Click Start Control Panel Hardware  
sensitive or not  
sensitive enough.  
and Sound Mouse icon.  
2. Within the Mouse Properties window, click  
the Device Settings tab.  
3. Click the Settings button.  
4. Properties for Synaptics Touch Pad Vx.x on  
PS/2 Port window is displayed.  
5. Select Sensitivity from the Select an item  
list.  
6. Select Touch Sensitivity and move the slider  
bar to adjust the sensitivity.  
7. Click the OK button.  
If you are still unable to resolve the problem,  
contact your reseller, dealer or service provider.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
9-15  
Troubleshooting  
USB mouse  
Problem  
Procedure  
On-screen pointer  
does not respond to  
mouse operation  
In this instance the system might be busy. Try  
moving the mouse again after waiting a short  
while.  
Remove the mouse from the computer and then  
reconnect it to a free USB port it in order to  
ensure it is firmly attached.  
Double-clicking does  
not work  
In this instance, you should initially try changing  
the double-click speed setting within the Mouse  
Control utility.  
1. To access this utility, click Start Control  
Panel Hardware and Sound Mouse  
icon.  
2. Within the Mouse Properties window, click  
the Buttons tab.  
3. Set the double-click speed as required and  
click OK.  
The mouse pointer  
moves too fast or too  
slow  
In this instance, you should initially try changing  
the speed setting within the Mouse Control utility.  
1. To access this utility, click Start Control  
Panel Hardware and Sound Mouse  
icon.  
2. Within the Mouse Properties window, click  
the Pointer Options tab.  
3. Set the pointer speed as required and click  
OK.  
The mouse pointer  
moves erratically  
The elements of the mouse responsible for  
detecting movement might be dirty - please refer  
to the documentation supplied with the mouse for  
instructions on how to clean it.  
If you are still unable to resolve the problem,  
contact your reseller, dealer or service provider.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
9-16  
 
Troubleshooting  
USB device  
In addition to the information in this section, please also refer to the  
documentation supplied with your USB device.  
Problem  
Procedure  
USB device does not  
work  
Remove the USB device from the computer and  
then reconnect it to a free port in order to ensure  
it is firmly attached.  
Ensure that any required USB device drivers are  
properly installed - to achieve this you should  
refer to both the device documentation and the  
operating system documentation.  
eSATA device  
In addition to the information in this section, please also refer to the  
documentation supplied with your eSATA device.  
Problem  
Procedure  
eSATA device does  
not work  
Remove the eSATA device from the computer  
and then reconnect it to a free port it in order to  
ensure it is firmly attached.  
A connected eSATA device may not be  
recognized if it is connected to the computer's  
eSATA/USB combo port while the computer is in  
Sleep Mode or Hibernation Mode. If this occurs,  
disconnect the eSATA device and then reconnect  
the device while the computer is turned on.  
Ensure that any required eSATA device drivers  
are properly installed - to achieve this you should  
refer to both the device documentation and the  
operating system documentation.  
If you are still unable to resolve the problem,  
contact your reseller, dealer or service provider.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
9-17  
       
Troubleshooting  
Additional memory module  
Please also refer to Chapter 8, Optional Devices, for further information on  
installing and removing memory modules.  
Problem  
Procedure  
If there is a memory  
In the event of Power indicator flashes when the  
malfunction, the Power computer is turned on you should initially ensure  
indicator will repeatedly that the installed memory module(s) are  
flash (on for 0.5  
seconds, off for 0.5  
seconds) in the  
compatible with the computer. If you determine  
that an incompatible module has been installed,  
you should follow the steps as detailed below:  
following patterns:  
1. Turn off the computer.  
If there is an error in  
only slot A or no  
memory module is  
inserted in Slot A:  
amber twice, then green  
once.  
2. Disconnect the AC adaptor and all peripheral  
devices.  
3. Remove the battery pack.  
4. Remove the incompatible memory module.  
5. Install the battery and/or connect the AC  
adaptor.  
If there is an error in  
Slot B: amber once,  
then green twice.  
6. Turn on the computer.  
If you are still unable to resolve the problem,  
contact your reseller, dealer or service provider.  
If there are errors in  
both Slot A and Slot B:  
amber twice, then green  
twice.  
An error will occur if a Remove the memory module from Slot B and  
memory module is  
inserted into Slot B  
while no memory  
module is inserted in  
Slot A.  
insert it into Slot A.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
9-18  
Troubleshooting  
Sound system  
In addition to the information in this section, please also refer to the  
documentation supplied with your audio device.  
Problem  
Procedure  
No sound is heard  
Adjust the volume control.  
Turn the dial clockwise to increase the volume  
and turn the dial counterclockwise to decrease  
the volume.  
Check the software volume settings.  
Please check to see if Mute is turned to Off.  
Check to make sure the headphone connection  
is secure.  
Check within the Windows Device Manager  
application to ensure the sound function is  
enabled.  
If you are still unable to resolve the problem,  
contact your reseller, dealer or service provider.  
Annoying sound is  
heard  
In this instance you may be experiencing  
feedback from either the internal microphone or  
an external microphone connected to the  
computer - please refer to Sound system in  
Chapter 4, Operating Basics for further  
information.  
Volume cannot be adjusted when Windows is  
turned on or turned off.  
If you are still unable to resolve the problem,  
contact your reseller, dealer or service provider.  
Volume control  
Problem  
Procedure  
No sound is heard  
Adjust the volume control.  
Turn the dial clockwise to increase the volume  
and Turn the dial counterclockwise to decrease  
the volume.  
Turn the volume control while verifying the  
volume in order to adjust.  
Annoying sound is  
heard  
Volume cannot be adjusted when Windows is  
turned on or turned off.  
If you are still unable to resolve the problem,  
contact your reseller, dealer or service provider.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
9-19  
 
Troubleshooting  
External monitor  
Please also refer to Chapter 8, Optional Devices, and to the documentation  
supplied with your monitor for further information.  
Problem  
Procedure  
Monitor does not turn After confirming that the monitor's power switch  
on  
is on, you should check the connections to make  
sure that the power cord/adaptor is firmly  
connected to the monitor and to a working power  
outlet.  
No display  
Try adjusting the contrast and brightness controls  
on the external monitor.  
Press the FN + F5 hot key in order to change the  
display priority and ensure that it is not set for the  
internal display panel only.  
Check to see if the external monitor is connected.  
When the external monitor is set as the primary  
display device in extended desktop mode, it will  
not display when the computer wakes up from  
Sleep Mode if the external monitor has been  
disconnected while in Sleep Mode.  
To keep this from happening, do not disconnect  
the external monitor while the computer is in  
Sleep or Hibernation Mode.  
Remember to turn off the computer before  
disconnecting the external monitor.  
When the display panel and an external monitor  
are set to clone mode and the monitors are  
turned off by the timer, the display panel or the  
external monitor may not display when turned on  
again.  
If this occurs, press FN + F5 to re-set the display  
panel and external monitor to clone mode.  
Display error occurs  
Check that the cable connecting the external  
monitor to the computer is firmly attached.  
If you are still unable to resolve the problem,  
contact your reseller, dealer or service provider.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
9-20  
   
Troubleshooting  
Modem  
This information is applicable to the models equipped with a built-in  
modem.  
Problem  
Procedure  
Communication  
Make sure the computer's internal modem  
software can’t initialize settings are correct. Please refer to the Phone  
modem  
and Modem Options link within the Windows  
Control Panel.  
You can hear a dial  
If the call is going through a Private Branch  
tone but can’t make a Exchange (PBX), take care to ensure that the  
call  
communication application's tone dial detection  
feature is disabled.  
You place a call, but a Make sure that the settings are correct within  
connection can’t be  
made  
your communication application.  
After making a call you Ensure that the communication application's tone  
can’t hear a ring or pulse dialling selection feature is set correctly.  
Communication is cut The computer will automatically cut off  
off unexpectedly  
communication when connection with the carrier  
is not successful for a set time interval - try  
lengthening this time interval within your  
communication application.  
A CONNECTdisplay is Ensure that the communication application's  
quickly replaced by NO error control feature is set correctly.  
CARRIER  
Character display  
becomes garbled  
during a  
When transmitting data you should ensure that  
the parity bit and stop bit settings correspond  
with those of the remote computer. You should  
check the flow control and communication  
protocol settings within your communication  
application.  
communication  
You cannot receive an Ensure that the communication application's  
incoming call  
rings before auto answer feature is set correctly.  
If you are still unable to resolve the problem,  
contact your reseller, dealer or service provider.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
9-21  
   
Troubleshooting  
LAN  
Problem  
Procedure  
Cannot access LAN  
Check for a firm cable connection between the  
Wake-up on LAN does Make sure the AC adaptor is connected. The  
not work  
Wake-up on LAN function consumes power even  
when the system is off.  
If problems persist, consult your LAN  
administrator.  
Wireless LAN  
If the following procedures do not restore LAN access, consult your LAN  
Chapter 4, Operating Basics.  
Problem  
Procedure  
Cannot access  
Wireless LAN  
Click Start J All programs J Toshiba J  
Utilities J Toshiba HWSetup and click Lan tab  
to check the Wireless Communication Switch  
setting is "ON".  
Bluetooth  
For further information on Bluetooth wireless communication, please refer  
to Chapter 4, Operating Basics.  
Problem  
Procedure  
Cannot access  
Bluetooth device  
Check to ensure the Bluetooth Manager  
application is running on the computer and that  
power to the external Bluetooth device is turned  
on.  
Check to ensure that no optional Bluetooth  
Adaptor is installed in the computer - the built-in  
Bluetooth hardware cannot operate  
simultaneously with another Bluetooth controller.  
If you are still unable to resolve the problem,  
contact your reseller, dealer or service provider.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
9-22  
         
Troubleshooting  
HDMI monitor output function  
Problem  
Procedure  
No display  
Try adjusting the contrast and brightness controls  
on the television.  
Press the FN + F5 hot key in order to change the  
display priority and ensure that it is not set for the  
internal display panel only.  
If you are still unable to resolve the problem,  
contact your reseller, dealer or service provider.  
If you turn the computer off into Sleep Mode while the display is on TV, the  
computer will select either the internal LCD or an external computer CRT  
as the display device the next time is switched on.  
TOSHIBA support  
If you require any additional help using your computer or if you are having  
problems operating the computer, you may need to contact TOSHIBA for  
additional technical assistance.  
Before you call  
Some problems you experience may be related to software or the operating  
system so it is important that you investigate other sources of assistance  
first. Before contacting TOSHIBA, try the following:  
Review troubleshooting sections in the documentation supplied with  
your software and/or peripheral devices.  
If a problem occurs when you are running software applications, consult  
the software documentation for troubleshooting suggestions and  
consider calling the software company's technical support department  
for assistance.  
Consult the reseller or dealer from where you purchased your computer  
and/or software - they are your best resource for current information  
and support.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
9-23  
       
Troubleshooting  
Where to write  
If you are still unable to solve the problem and suspect that it is hardware  
related, write to TOSHIBA at the nearest location listed below:  
Outside of Europe  
Australia  
In Europe  
Germany & Austria  
TOSHIBA Australia Pty. Ltd.  
Information Systems Division  
Building C, 12-24 Talavera Rd,  
North Ryde, 2113, NSW, Australia  
Toshiba Europe GmbH  
Hammfelddamm 8  
D-41460, Neuss, Deutschland  
Canada  
France  
TOSHIBA of Canada Ltd.  
191 McNabb Street, Markham,  
Ontario L3R 8H2  
Toshiba Systèmes (France) S.A.  
7 Rue Ampère B.P. 131  
92804, Puteaux Cédex, France  
China  
Netherlands  
TOSHIBA Personal Computer &  
Network (Shanghai) Co., Ltd.  
10F, BEA Finance Tower, No.66  
Toshiba Information Systems  
Benelux  
Westbroek 36-46 4822 ZW, Breda,  
Hua Yuan Shi Qiao Road, Pudong, Nederland  
Shanghai, P.R.China 200120  
Singapore  
Spain  
Toshiba Singapore Pte., Ltd.  
438B Alexandra Road Alexandra  
Technopark #06-01 Singapore  
119968  
Toshiba Europe GmbH Sucursal en  
España  
Parque Empresarial San Fernando  
Edificio Europa, 1a Planta, Escalera  
A 28830, Madrid, España  
United States of America  
United Kingdom  
Toshiba America Information  
Systems, Inc.  
Digital Products Division  
9740 Irvine Boulevard  
Irvine, CA 92618-1697  
Toshiba Information Systems (UK) Ltd  
Toshiba Court, Weybridge Business  
Park, Addlestone Road KT15 2UL,  
Weybridge, Surrey, United Kingdom  
India  
The Rest of Europe  
Toshiba India Pvt. Ltd  
Toshiba Europe GmbH  
Hammfelddamm 8  
D-41460, Neuss, Deutschland  
6F, Dr. Gopal Das Bhawan,  
28, Barakhamba Road,  
New Delhi - 110001 India  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
9-24  
Chapter 10  
Disclaimers  
This chapter slates the Disclaimer(s) information applicable to TOSHIBA  
computers.  
CPU  
Central Processing Unit ("CPU") Performance Disclaimer.  
CPU performance in your computer product may vary from specifications  
under the following conditions:  
use of certain external peripheral products  
use if battery power instead of AC power  
use of certain multimedia, computer generated graphics or video  
applications  
use of standard telephone lines or low speed network connections  
use of complex modeling software, such as high end computer aided  
design applications  
use of several applications or functionalities simultaneously  
use of computer in areas with low air pressure (high altitude >1,000  
meters or >3,280 feet above sea level)  
use of computer at temperatures outside the range of 5°C to 35°C (41°F  
to 95°F) or >25°C (77°F) at high altitude (all temperature references are  
approximate and may vary depending on the specific computer model -  
please refer to your computer documentation or visit the Toshiba  
website at www.pcsupport.toshiba.com for details).  
CPU performance may also vary from specifications due to design  
configuration.  
User’s Manual  
10-1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Disclaimers  
Under some conditions, your computer product may automatically shut-  
down. This is a normal protective feature designed to reduce the risk of lost  
data or damage to the product when used outside recommended  
conditions. To avoid risk of lost data, always make back-up copies of data  
by periodically storing it on an external storage medium. For optimum  
performance, use your computer product only under recommended  
conditions. Read additional restrictions under "Environmental Conditions"  
in your computer documentation.  
Contact Toshiba Technical Service and Support for more information.  
64-Bit Computing  
64-bit processors are designed to take advantage of 32 and 64 bit  
computing.  
64-bit computing requires that the following hardware and software  
requirements are met:  
64-bit Operating System  
64-bit CPU, Chipset and BIOS (Basic Input/Output System)  
64-bit Device drivers  
64-bit applications  
Certain device drivers and/or applications may not be compatible with a  
64-bit CPU and therefore may not function properly.  
Memory (Main System)  
Part of the main system memory may be used by the graphics system for  
graphics performance and therefore reduce the amount of main system  
memory available for other computing activities. The amount of main  
system memory allocated to support graphics may vary depending on the  
graphics system, applications utilized, system memory size and other  
factors. Computers configured with a 32-bit operating system can address  
up to 3GB of system memory. Only computers configured with a 64-bit  
operating system can address 4GB or more of system memory.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
10-2  
 
Disclaimers  
Battery Life  
Battery life may vary considerably depending on product model,  
configuration, applications, power management settings and features  
utilized, as well as the natural performance variations produced by the  
design of individual components. Published battery life numbers are  
achieved on select models and configurations tested by Toshiba at the time  
of publication. Recharge time varies depending on usage. Battery may not  
charge while computer is consuming full power.  
After a period of time, the battery will lose its ability to perform at maximum  
capacity and will need to be replaced. This is normal for all batteries. To  
purchase a new battery pack, see the accessories information that shipped  
with your computer.  
HDD drive capacity  
One Gigabyte (GB) means 109 = 1,000,000,000 bytes using powers of 10.  
The computer operating system, however, reports storage capacity using  
powers of 2 for the definition of 1 GB = 230 = 1,073,741,824 bytes, and  
therefore shows less storage capacity. Available storage capacity will also  
be less if the product includes one or more pre-installed operating systems,  
such as Microsoft Operating System and/or pre-installed software  
applications, or media content. Actual formatted capacity may vary.  
LCD  
Over a period of time, and depending on the usage of the computer, the  
brightness of the LCD screen will deteriorate. This is an intrinsic  
characteristic of LCD technology.  
Maximum brightness is only available when operating in AC power mode.  
Screen will dim when the computer is operated on battery power and you  
will not be able to increase the brightness of the screen.  
Graphics Processor Unit ("GPU”)  
Graphics processor unit ("GPU") performance may vary depending on  
product model, design configuration, applications, power management  
settings and features utilized. GPU performance is only optimized when  
operating in AC power mode and may decrease considerably when  
operating in battery power mode.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
10-3  
       
Disclaimers  
Wireless LAN  
The transmission speed over the wireless LAN and the distance over which  
wireless LAN can reach may vary depending on surrounding  
electromagnetic environment, obstacles, access point design and  
configuration, and client design and software/hardware configurations.The  
actual transmission speed will be lower than the theoretical maximum  
speed.  
External HDD Capacity  
One Gigabyte (GB) means 109 =1,000,000,000 bytes using powers of 10. A  
computer operating system, however, reports storage capacity using  
powers of 2 for the definition of 1GB=230=1,073,741,824 bytes, and  
therefore shows less storage capacity. Available storage capacity will also  
be less if the computer includes one or more pre-installed operating  
systems, pre-installed software applications, or media content. Actual  
formatted capacity may vary.  
Non-applicable Icons  
Certain notebook chassis are designed to accommodate all possible  
configurations for an entire product series. Your selected model may not  
have all the features and specifications corresponding to all of the icons or  
switches shown on the notebook chassis, unless you have selected all  
those features.  
Copy Protection  
Applicable copy protection standards included in certain media may  
prevent or limit recording or viewing of the media.  
Images  
All images are simulated for purposes of illustration.  
LCD Brightness and Eye Strain  
Your display panel has a brightness approaching that of a TV device. We  
recommend that you adjust the brightness of your LCD to a comfortable  
level to prevent possible strain on your eyes.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
10-4  
           
Appendix A Specifications................................................................................A-1  
Appendix B Display Controller.........................................................................B-1  
Appendix C V.90/V.92.........................................................................................C-1  
Appendix D Wireless LAN.................................................................................D-1  
Appendix E AC Power Cord and Connectors................................................. E-1  
Appendix F TOSHIBA PC Health Monitor....................................................... F-1  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Appendixes-1  
Appendix A  
Specifications  
This appendix summarizes the computer’s technical specifications.  
Environmental requirements  
Operating  
5°C to 35°C  
Non-operating  
Ambient  
temperature  
-20°C to 60°C  
Relative humidity 20% to 80%  
10% to 90%  
Altitude (from  
sea level)  
0 to 3,000 meters  
0 to 10,000 meters  
Power Requirements  
AC adaptor  
100-240 volts AC  
50 or 60 hertz (cycles per second)  
Computer  
19V DC  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
A-1  
     
Built-in Modem  
The ability of this feature is depending on the model you purchased.  
Network control unit (NCU)  
Type of NCU  
Type of line  
AA  
Telephone line (analog only)  
Type of dialing  
Pulse  
Tone  
Control command  
AT commands  
EIA-578 commands  
Monitor function  
Computer’s speaker  
Communication specifications  
Communication  
system  
Data:  
Fax:  
Full duplex  
Half duplex  
Communication  
protocol  
Data  
ITU-T-Rec  
(Former CCITT)  
V.21/V.22/V.22bis/V.32/V.32  
bis/V.34/V.90  
Bell  
Fax  
103/212A  
ITU-T-Rec  
V.17/V.29/V.27ter/V.21 ch2  
(Former CCITT)  
Communication  
speed  
Data transmission and reception  
300/1200/2400/4800/7200/9600/12000/14400/16  
800/19200/21600/24000/26400/28800/31200/33  
600 bps  
Data reception only with V.90  
28000/29333/30666/32000/33333/34666/36000/  
37333/38666/40000/41333/42666/44000/45333/  
46666/48000/49333/50666/52000/53333/54666/  
56000 bps  
Fax  
2400/4800/7200/9600/12000/14400 bps  
Error correcting  
MNP class 4 and ITU-T V.42  
Data compression  
MNP class 5 and ITU-T V.42bis  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
A-2  
Appendix B  
Display Controller  
Display controller  
The display controller interprets software commands into hardware  
commands that turn particular pixels on or off.  
The controller is an advanced Video Graphics Array (VGA) that provides  
Super VGA (SVGA) and Extended Graphics Array (XGA) support for the  
internal LCD and external monitors.  
A high-resolution external monitor connected to the computer can display  
up to 2048 horizontal and 1536 vertical pixels at up to 16M colors.  
The display controller also controls the video mode, which uses industry  
standard rules to govern the screen resolution and the maximum number of  
colors that can be displayed on screen.  
Software written for a given video mode will run on any computer that  
supports the mode.  
The computer’s display controller supports all SVGA and XGA modes, the  
most widely used industry standards.  
Some of display modes might not be supported depending on the external  
monitor which you use.  
If you are running some application (for example a 3D application or video  
playback and so on), you may see some disturbance, flickering or frame  
dropping on your screen. If that occurs, adjust the resolution of display,  
lowering it until the screen is displayed properly. You could also disable  
Windows Aeroto help correct this situation.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
B-1  
         
Appendix C  
V.90/V.92  
The TOSHIBA internal modem uses V.90 technology. The modem is  
capable of downstream speeds of 56Kbps (kilobits per second) when  
connected to an Internet service provider that supports V.90/V.92. As with  
any modem, the actual throughput (speed of data transfer) depends on  
analog telephone line conditions, which can vary considerably. Therefore,  
many users will experience throughput in the range of 32-44Kbps under  
normal telephone line conditions. Upstream data flows at the V.34 rate.  
V.90 rates can be achieved only when one V.90 capable modem is  
connected to another. The TOSHIBA Internal modem will select  
automatically V.34 if the remote modem lacks V.90 capability or if a  
combination of network and/or phone line conditions prevent V.90  
connection.  
V.90/V.92 mode  
Function  
Data V.90/V.92  
Transmission speed  
From 56K (maximum) to 28Kbps (minimum)  
Reception only  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
C-1  
     
Table Result codes for a V.90 connection  
No.  
70  
Result code  
Description  
CONNECT 32000 EC*  
CONNECT 36000 EC*  
CONNECT 40000 EC*  
CONNECT 44000 EC*  
CONNECT 48000 EC*  
CONNECT 52000 EC*  
CONNECT 56000 EC*  
CONNECT 28000 EC*  
CONNECT 29333 EC*  
CONNECT 30666 EC*  
CONNECT 33333 EC*  
CONNECT 34666 EC*  
CONNECT 37333 EC*  
CONNECT 38666 EC*  
CONNECT 41333 EC*  
CONNECT 42666 EC*  
CONNECT 45333 EC*  
CONNECT 46666 EC*  
CONNECT 49333 EC*  
CONNECT 50666 EC*  
CONNECT 53333 EC*  
CONNECT 54666 EC*  
Connection at 32000 bits/s  
Connection at 36000 bits/s  
Connection at 40000 bits/s  
Connection at 44000 bits/s  
Connection at 48000 bits/s  
Connection at 52000 bits/s  
Connection at 56000 bits/s  
Connection at 28000 bits/s  
Connection at 29333 bits/s  
Connection at 30666 bits/s  
Connection at 33333 bits/s  
Connection at 34666 bits/s  
Connection at 37333 bits/s  
Connection at 38666 bits/s  
Connection at 41333 bits/s  
Connection at 42666 bits/s  
Connection at 45333 bits/s  
Connection at 46666 bits/s  
Connection at 49333 bits/s  
Connection at 50666 bits/s  
Connection at 53333 bits/s  
Connection at 54666 bits/s  
72  
74  
76  
78  
80  
82  
100  
101  
102  
103  
104  
105  
106  
107  
108  
109  
110  
111  
112  
113  
114  
*EC stands for the Error Control method, which appears only when the  
extended result codes configuration option is enabled. EC is replaced by  
one of the following symbols, depending on the error control method used.  
V42bis  
V42  
V.42 error control and V.42bis data compression  
V.42 error control only  
NoEC  
No error control protocol  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
C-2  
AT Command  
-V90=*  
V.90 Dial Line Rate  
-V90 sets the maximum V.90 downstream that the  
modem attempts to connect  
-V90=0  
-V90=1  
V.90 disabled  
V.90 enabled: automatic speed selection -  
maximum modem speed(default)  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
C-3  
 
Appendix D  
Wireless LAN  
This appendix is intended to help you get your Wireless LAN network up  
and running, with a minimum of parameters.  
Card Specifications  
Form Factor  
Compatibility  
Mini Card  
IEEE 802.11 Standard for Wireless LANS  
Wi-Fi (Wireless Fidelity) certified by the Wi-Fi  
Alliance. The ‘Wi-Fi CERTIFIED’ logo is a  
certification mark of the Wi-Fi Alliance.  
Windows® Networking  
Network Operating  
System  
CSMA/CA (Collision Avoidance) with  
Media Access  
Protocol  
Acknowledgment (ACK)  
54/48/36/24/18/9/6 Mb/s (Revision A and G)  
Data Rate  
11/5.5/2/1 Mb/s (Revision B)  
User’s Manual  
D-1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Radio Characteristics  
Radio Characteristics of Wireless LAN Cards may vary according to:  
Country/region where the product was purchased  
Type of product  
Wireless communication is often subject to local radio regulations.  
Although Wireless LAN wireless networking products have been designed  
for operation in the license-free 2.4GHz and 5GHz band, local radio  
regulations may impose a number of limitations to the use of wireless  
communication equipment.  
Refer to the sheet “Information to the User” for regulatory information that  
may apply in your country/region.  
Band 5 GHz (5150-5850 MHz) (Revision A, N)  
R-F Frequency  
Band 2.4 GHz (2400-2483.5 MHz)  
(Revision B, G, N)  
The range of the wireless signal is related to the transmit rate of the  
wireless communication. Communications at lower transmit range may  
travel larger distances.  
The range of your wireless devices can be affected when the antennas  
are placed near metal surfaces and solid high-density materials.  
Range is also impacted due to "obstacles" in the signal path of the radio  
that may either absorb or reflect the radio signal.  
Supported Frequency Sub-bands  
Subject to the radio regulations that apply in the countries/regions, your  
Wireless LAN card may support a different set of 5 GHz/2.4 GHz channels.  
Consult your Authorized Wireless LAN or TOSHIBA Sales office for  
information about the radio regulations that apply in the countries/regions.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
D-2  
   
Table Wireless IEEE 802.11 Channels Sets (Revision B and G)  
Frequency Range Channel ID  
2400-2483.5 MHz  
2412  
1
2
2417  
3
2422  
4
2427  
5
2432  
6
2437  
7
2442  
8
2447  
9
2452  
1
10  
11  
12  
13  
2457*  
2462  
2
2467*  
2
2472*  
When installing Wireless LAN cards, the channel configuration is managed  
as follows:  
For wireless clients that operate in a Wireless LAN infrastructure, the  
Wireless LAN card will automatically start operation at the channel  
identified by the Wireless LAN Access Point. When roaming between  
different access points the station can dynamically switch to another  
channel if required.  
In a Wireless LAN Access Point, the Wireless LAN card will use the  
factory-set default channel (printed in bold), unless the LAN  
Administrator selected a different channel when configuring the  
Wireless LAN Access Point device.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
D-3  
Table Wireless IEEE 802.11 Channels Sets (Revision A)  
Frequency Range Channel ID  
5150-5850 MHz  
5180  
Note  
36  
40  
5200  
44  
5220  
48  
5240  
52  
5260  
56  
5280  
60  
5300  
64  
5320  
*3  
100  
104  
108  
112  
116  
120  
124  
128  
132  
136  
140  
149  
153  
157  
161  
5500  
*3  
5520  
*3  
5540  
*3  
5560  
*3  
5580  
*3  
5600  
*3  
5620  
*3  
5640  
*3  
5660  
*3  
5680  
*3  
5700  
*3  
*4  
*4  
*4  
*4  
5745  
US only  
US only  
US only  
US only  
*3  
5765  
*3  
5785  
*3  
5805  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
D-4  
*1 Factory-set default channels  
*2 Refer to the sheet Approved Countries/Regions for use for the  
countries/regions that in which these channels can be used.  
*3 These channels are available to A/B/G/N combo type only.  
*4 Available Area: US (USA, CANADA) only.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
D-5  
Appendix E  
AC Power Cord and Connectors  
The AC input plug of power cord must be compatible with various  
international AC power outlets. Power cords need to meet the local  
standards and the specifications listed as below:  
Length:  
Minimum 1.7 meters  
2
Wire size:  
Minimum 0.75 mm  
Current rating:  
Voltage rating:  
Minimum 2.5 amperes  
90 or 264 VAC  
(depending on country/region’s power standards)  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
E-1  
   
Certification agencies  
Europe:  
Austria:  
Belgium:  
Denmark:  
Finland:  
France:  
OVE  
Italy:  
IMQ  
CEBEC  
DEMKO  
FIMKO  
LCIE  
The Netherlands:  
Norway:  
KEMA  
NEMKO  
SEMKO  
SEV  
Sweden:  
Switzerland:  
United Kingdom:  
Germany:  
VDE  
BSI  
Outside of Europe:  
U.S. and Canada: UL listed and CSA certified  
No. 18 AWG, Type SVT or SPT-2  
China:  
CCC, CQC  
AS  
India:  
STQC  
Australia:  
In Europe, two conductors power cord must be VDE type, H05VVH2-F or  
H03VVH2-F and for three conductors power cord must be VDE type,  
H05VV-F.  
For the United States and Canada, two pin plug configuration must be a  
2-15P (250V) or 1-15P (125V) and three pin plug configuration must be  
6-15P (250V) or 5-15P (125V) as designated in the U.S. National Electrical  
code handbook and the Canadian Electrical Code Part II.  
The following illustrations show the plug shapes for USA, Australia,  
Canada, United Kingdom, Europe, and China.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
E-2  
 
United Kingdom  
USA  
Australia  
Europe  
Canada  
China  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
E-3  
Appendix F  
TOSHIBA PC Health Monitor  
The TOSHIBA Health Monitor software program monitors computer system  
functions such as power consumption, the cooling system and HDD Drop  
sensor. It alerts users of specific system conditions via pop-up messages. It  
also tracks the usages of the computer and related devices, logging the  
service relevant information on the computer's hard disk drive.  
The collected information includes device operation time and number of  
actuations or status changes (i.e.: number of power button and FN key  
combination uses, AC adaptor, battery, LCD, fan, HDD, sound volume,  
wireless communication switch, TOSHIBA Express Port Replicator and  
USB information), date of initial system use, and also computer and device  
usage (i.e.: power settings, battery temperature and recharging, CPU,  
memory, backlight illumination time, and temperatures for various devices,  
property (e.g.: product name, model number, part number, serial number,  
BIOS version, FW version) of the system and components (e.g.: Video  
device, Sound device, Network device, Hard Disk drive, Solid State drive,  
Optical Disc drive), operating system and software information (e.g.: OS  
version, OS install date, Direct X version, Internet Explorer version,  
installed update program and driver lists). The stored data uses a very  
small portion of the total hard disk capacity, approximately 10MB or less per  
year.  
This information is used to identify and provide a notification of system  
conditions which may effect the performance of your computer. It may also  
be used to help diagnose problems should the computer require service by  
TOSHIBA or TOSHIBA's authorized service providers. Additionally,  
TOSHIBA may also use this information for quality assurance analysis.  
Subject to the use restrictions above , the HDD data logged may be  
transferred to entities located outside of your country or region of residence  
(e.g., European Union). Those countries may or may not have the same  
data protection laws or data protection levels as required by your home  
country or region.  
Once enabled, you may disable the TOSHIBA PC Health Monitor at any  
time by uninstalling the software via Uninstall a program in the Control  
Panel. Doing so will automatically delete all collected information from the  
HDD.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
F-1  
   
The TOSHIBA PC Health Monitor software does not extend or modify  
TOSHIBA's obligations under its standard limited warranty in any way.  
TOSHIBA's standard limited warranty terms and limitations apply. Visit  
http://www.warranty.toshiba.com for details.  
Starting the TOSHIBA PC Health Monitor  
The TOSHIBA PC Health Monitor can be started using the following  
methods:  
Click Start All Programs TOSHIBA Utilities PC Health  
Monitor.  
Click the icon in the notification area, then click the "Click here to  
enable TOSHIBA PC Health Monitor." message when it is displayed.  
This message will no longer be displayed after clicking "Please enable  
software now" or "Please disable software now" on the "PC Health Monitor  
Software Notice & Acceptance" screen.  
No matter which method is used, the TOSHIBA PC Health Monitor  
explanation screen will be displayed.  
Clicking "Next" will display the "PC Health Monitor Software Notice &  
Acceptance" screen. Please carefully read the information displayed.  
Selecting "Please enable software now. I agree with the terms and  
conditions and use and sharing of the information collected." and clicking  
"OK" will enable the program. By enabling the TOSHIBA PC Health Monitor  
software, you agree with these terms and conditions and to the use and  
sharing of the collected information. Once the program is enabled, the  
TOSHIBA PC Health Monitor screen is displayed, and the program will  
begin monitoring system functions and collecting information.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
F-2  
 
Glossary  
The terms in this glossary cover topics related to this manual. Alternate  
naming is included for reference.  
Abbreviations  
AACS: advanced access content system  
AC: Alternating current  
ACPI: Advanced Configuration and Power Interface  
ASCII: American Standard Code for Information Interchange  
BIOS: basic input/output system  
bps: bits per second  
CD: compact disc  
CD-ROM: Compact Disc Read-Only Memory  
CD-RW: Compact Disc-ReWritable  
CMOS: complementary metal-oxide semiconductor  
CPU: central processing unit  
CRT: cathode ray tube  
DC: direct current  
DDC: display data channel  
DDR: double data rate  
DIMM: dual inline memory module  
DVD: digital versatile disc  
DVD-R: Digital Versatile Disc Recordable  
DVD-RAM: Digital Versatile Disc Random Access Memory  
DVD-R (Dual Layer): Digital Versatile Disc Recordable Dual Layer  
DVD-ROM: Digital Versatile Disc Read Only Memory  
DVD-RW: Digital Versatile Disc ReWritable  
DVD+R (Double Layer): Digital Versatile Disc Recordable Double Layer  
FDD: floppy diskette drive  
FHD: Full High Definition  
FIR: fast infrared  
GB: gigabyte  
HDD: hard disk drive  
GPS: Global Positioning System  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Glossary-1  
   
Glossary  
HD+: High Definition Plus  
IDE: integrated drive electronics  
IEEE: Institute of Electrical and Electronics Engineers  
I/O: input/output  
IrDA: Infrared Data Association  
IRQ: interrupt request  
KB: kilobyte  
LAN: local area network  
LCD: liquid crystal display  
LED: light emitting diode  
MB: megabyte  
MMC: multi media card  
OCR: optical character recognition (reader)  
PCB: printed circuit board  
PCI: peripheral component interconnect  
RAM: random access memory  
RGB: red, green, and blue  
ROM: read only memory  
RTC: real time clock  
S/P DIF: Sony/Philips Digital Interface Format  
SDRAM: synchronous dynamic random access memory  
SLI: Scalable Link Interface  
SIM: Subscriber Identity Module  
SO-DIMM: small-outline dual in line memory module  
TFT: thin-film transistor  
UART: universal asynchronous receiver/transmitter  
USB: Universal Serial Bus  
UWB: Ultra Wide Band  
VESA: Video Electronic Standards Association  
VGA: video graphics array  
XGA: extended graphics array  
A
adaptor: A device that provides a compatible connection between two  
units. For example, the computer's internal display adapter receives  
information from the software and translates it into images on the  
screen. An adapter can take a number of forms, from a  
microprocessor to a simple connector: An intelligent adapter (one  
that is capable of doing some processing) may also be called a  
controller.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Glossary-2  
Glossary  
alphanumeric: Keyboard characters including letters, numbers and other  
symbols, such as punctuation marks or mathematical symbols.  
alternating current (AC): Electric current that reverses its direction of flow  
at regular intervals.  
analog signal: A signal whose characteristics such as amplitude and  
frequency vary in proportion to (are an analog of) the value to be  
transmitted. Voice communications are analog signals.  
application: A group of programs that together are used for a specific task  
such as accounting, financial planning, spreadsheets, word  
processing and games.  
ASCII: American Standard Code for Information Interchange. ASCII code is  
a set of 256 binary codes that represent the most commonly used  
letters, numbers, and symbols.  
asynchronous: Lacking regular time relationship. As applied to computer  
communications, asynchronous refers to the method of transmitting  
data that does not require a steady stream of bits to be transmitted  
at regular time intervals.  
B
backup: A copy of a file, usually on a removable disk, kept in case the  
original file is lost or damaged.  
binary: The base two number system composed of zeros and ones (off or  
on), used by most digital computers. The right-most digit of a binary  
number has a value of 1, the next a value of 2, then 4, 8, 16, and so  
on. For example, the binary number 101 has a value of 5. See also  
ASCII.  
BIOS: Basic Input/Output System. The firmware that controls data flow  
within the computer. See also firmware.  
bit: Derived from "binary digit," the basic unit of information used by the  
computer. It is either zero or one. Eight bits is one byte. See also  
byte.  
Bluetooth: A short-range radio technology designed to simplify wireless  
communication among computers, communication devices and the  
Internet.  
board: A circuit board. An internal card containing electronic components,  
called chips, which perform a specific function or increase the  
capabilities of the system.  
boot: Short for bootstrap. A program that starts or restarts the computer.  
The program reads instructions from a storage device into the  
computer’s memory.  
boot disk: See system disk.  
bootable disk: See system disk.  
bps: Bits per second. Typically used to describe the data transmission  
speed of a modem.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Glossary-3  
Glossary  
buffer: The portion of the computer’s memory where data is temporarily  
stored. Buffers often compensate for differences in the rate of flow  
from one device to another.  
bus: An interface for transmission of signals, data or electric power.  
byte: The representation of a single character. A sequence of eight bits  
treated as a single unit; also the smallest addressable unit within the  
system.  
C
cache memory: A section of very fast memory in which frequently used  
information is duplicated for quick access. Accessing data from  
cache is faster than accessing it from the computer's main memory.  
See also L1 cache, L2 cache.  
capacity: The amount of data that can be stored on a magnetic storage  
device such as a floppy diskette or hard disk drive. It is usually  
described in terms of kilobytes (KB), where one KB = 1024 bytes,  
megabytes (MB), where one MB = 1024 KB and gigabytes (GB),  
where one GB = 1024 MB.  
CD: An individual compact disc. See also CD-ROM.  
CD-R: A Compact Disc-Recordable disc can be written once and read  
many times. See also CD-ROM.  
CD-ROM: A Compact Disc Read-Only Memory is a high capacity disc that  
can be read from but not written to. The CD-ROM drive uses a laser,  
rather than magnetic heads, to read data from the disc.  
CD-RW: A Compact Disc-ReWritable disc can be rewritten many times.  
See also CD-ROM.  
character: Any letter, number, punctuation mark, or symbol used by the  
computer. Also synonymous with byte.  
chassis: The frame containing the computer.  
chip: A small semiconductor containing computer logic and circuitry for  
processing, memory, input/output functions and controlling other  
chips.  
click: To press and release the pointing device's primary button without  
moving the pointing device. In the Windows operating system, this  
refers to the pointing device's left button, unless otherwise stated.  
See also double-click.  
CMOS: Complementary Metal-Oxide Semiconductor. An electronic circuit  
fabricated on a silicon wafer that requires very little power.  
Integrated circuits implemented in CMOS technology can be tightly  
packaged and are highly reliable.  
cold start: Starting a computer that is currently off (turning on the power).  
COM1, COM2, COM3 and COM4: The names assigned to the serial and  
communication ports.  
commands: Instructions you enter at the terminal keyboard that direct the  
actions of the computer or its peripheral devices.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Glossary-4  
Glossary  
compatibility: 1) The ability of one computer to accept and process data in  
the same manner as another computer without modifying the data  
or the media upon which it is being transferred. 2) the ability of one  
device to connect to or communicate with another system or  
component.  
components: Elements or parts (of a system) which make up the whole  
(system).  
Composite Video (YUV): A standard video signal used to transmit images,  
e.g. from a VCR to a TV.  
computer program: A set of instructions written for a computer that enable  
it to achieve a desired result.  
computer system: A combination of hardware, software, firmware, and  
peripheral components assembled to process data into useful  
information.  
configuration: The specific components in your system (such as the  
terminal, printer, and disk drives) and the settings that define how  
your system works. You use the HW Setup program to control your  
system configuration.  
controller: Built-in hardware and software that controls the functions of a  
specific internal or peripheral device (e.g. keyboard controller).  
co-processor: A circuit built into the processor that is dedicated to  
intensive math calculations.  
CPU: Central Processing Unit. The portion of the computer that interprets  
and executes instructions.  
CRT: Cathode Ray Tube. A vacuum tube in which beams projected on a  
fluorescent screen-producing luminous spots. An example is the  
television set.  
cursor: A small, blinking rectangle or line that indicates the current position  
on the display screen.  
D
data: Information that is factual, measurable or statistical that a computer  
can process, store, or retrieve.  
data bits: A data communications parameter controlling the number of bits  
(binary digits) used to make up a byte. If data bits = 7 the computer  
can generate 128 unique characters. If data bits = 8 the computer  
can generate 256 unique characters.  
DC: Direct Current. Electric current that flows in one direction. This type of  
power is usually supplied by batteries.  
default: The parameter value automatically selected by the system when  
you or the program do not provide instructions. Also called a preset  
value.  
delete: To remove data from a disk or other data storage device.  
Synonymous with erase.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Glossary-5  
Glossary  
device driver: A program (called a "driver") that permits a computer to  
communicate with a device.  
dialog box: A window that accepts user input to make system settings or  
record other information.  
disable: To turn a computer option off. See also enable.  
Digital Audio: An audio compression standard that enables high-quality  
transmission and real-time playback of sound files.  
disk drive: The device that randomly accesses information on a disk and  
copies it to the computer's memory. It also writes data from memory  
to the disk. To accomplish these tasks, the unit physically rotates the  
disk at high speed past a read-write head.  
disk storage: Storing data on magnetic disk. Data is arranged on  
concentric tracks much like a phonograph record.  
display: A CRT, LCD, or other image producing device used to view  
computer output.  
documentation: The set of manuals and/or other instructions written for  
the users of a computer system or application. Computer system  
documentation typically includes procedural and tutorial information  
as well as system functions.  
double click: To press and release the pointing device's primary button  
rapidly twice without moving the pointing device. In the Windows  
operating system, this refers to the pointing device's left button,  
unless otherwise stated.  
driver: A software program, generally part of the operating system, that  
controls a specific piece of hardware (frequently a peripheral device  
such as a printer or mouse).  
DVD: An individual digital versatile (or video) disc. See also DVD-ROM.  
DVB-T (Digital Video Broadcasting - Terrestrial): Also known as  
terrestrial digital TV. Digital TV broadcasting standard.  
DVD-R (+R, -R): A Digital Versatile Disc Recordable disc can be written  
once and read many times. The DVD-R drive uses a laser to read  
data from the disc.  
DVD-RAM: A Digital Versatile Disc-Random Access Memory is a high  
capacity, high performance disc that lets you store large volumes of  
data. The DVD-RAM drive uses a laser to read data from the disc.  
DVD-R (Dual Layer): A disc having two layers on one side with the DVD-R  
storage capacity about 1.8 times larger than before. The DVD-RW  
drive uses a laser to read data from the disc.  
DVD-ROM: A Digital Versatile Disc-Read Only Memory is a high capacity,  
high performance disc suitable for play back of video and other  
high-density files. The DVD-ROM drive uses a laser to read data  
from the disc.  
DVD-RW (+RW, -RW): A Digital Versatile Disc-ReWritable disc can be  
rewritten many times.  
DVD+R (Double Layer): A disc having two layers on one side with the  
DVD+R storage capacity about 1.8 times larger than before. The  
DVD-RW drive uses a laser to read data from the disc.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Glossary-6  
Glossary  
E
echo: To send back a reflection of the transmitted data to the sending  
device. You can display the information on the screen, or output it to  
the printer, or both. When a computer receives back data it  
transmitted to a CRT (or other peripheral device) and then transmits  
the data to printer, the printer is said to echo the CRT.  
enable: To turn on a computer option. See also disable.  
erase: See delete.  
escape: 1) A code (ASCII code 27), signaling the computer that what  
follows are commands; used with peripheral devices such as  
printers and modems. 2) A means of aborting the task currently in  
progress.  
escape guard time: A time before and after an escape code is sent to the  
modem which distinguishes between escapes that are part of the  
transmitted data, and escapes that are intended as a command to  
the modem.  
execute: To interpret and execute an instruction.  
F
file: A collection of related information; a file can contain data, programs, or  
both.  
firmware: A set of instructions built into the hardware which controls and  
directs a microprocessor°Øs activities.  
flash memory: Non-volatile memory that can be written to as well as read.  
Information in flash memory remains whether or not the computer is  
receiving power. See also memory. Compare RAM and ROM.  
floppy diskette: A removable disk that stores magnetically encoded data.  
floppy diskette drive (FDD): An electromechanical device that reads and  
writes to floppy diskettes.  
Fn-esse: A TOSHIBA utility that lets you assign functions to hot keys.  
folder: An icon in Windows used to store documents or other folders.  
format: The process of preparing a blank disk for its first use. Formatting  
establishes the structure of the disk that the operating system  
expects before it writes files or programs onto the disk.  
function keys: The keys labeled F1 through F9 that tell the computer to  
perform certain functions.  
G
gigabyte (GB): A unit of data storage equal to 1024 megabytes. See also  
megabyte.  
graphics: Drawings, pictures, or other images, such as charts or graphs, to  
present information.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Glossary-7  
Glossary  
H
hard disk: A storage device composed of a rigid platter or platters that can  
be magnetically coded with data. Hard disks hold much more  
information than diskettes and are used for long-term storage of  
programs and data. The primary (or only) hard disk in a computer is  
usually fixed, but some computers have secondary hard disks that  
are removable. By default, the hard disk is referred to as drive C.  
hard disk drive (HDD): An electromechanical device that reads and writes  
a hard disk. See also hard disk.  
hardware: The physical electronic and mechanical components of a  
computer system: typically, the computer itself, external disk drives,  
etc. See also software and firmware.  
hertz: A unit of wave frequency that equals one cycle per second.  
host computer: The computer that controls, regulates, and transmits  
information to a device or another computer.  
hot key: The computer's feature in which certain keys in combination with  
the extended function key, FN, can be used to set system  
parameters, such as speaker volume.  
HW Setup: A TOSHIBA utility that lets you set the parameters for various  
hardware components.  
I
icon: A small graphic image displayed on the screen or in the indicator  
panel. In Windows, an icon represents an object that the user can  
manipulate.  
input: The data or instructions you provide to a computer, communication  
device or other peripheral device from the keyboard or external or  
internal storage devices. The data sent (or output) by the sending  
computer is input for the receiving computer.  
instruction: Statements or commands that specify how to perform a  
particular task.  
interface: 1) Hardware and/or software components of a system used  
specifically to connect one system or device to another. 2) To  
physically connect one system or device to another to exchange  
information. 3) The point of contact between user, the computer, and  
the program, for example, the keyboard or a menu.  
interrupt request: A signal that gives a component access to the  
processor.  
I/O: Input/output. Refers to acceptance and transfer of data to and from a  
computer.  
I/O devices: Equipment used to communicate with the computer and  
transfer data to and from it.  
IrDA 1.1: An industry standard that enables cableless infrared serial data  
transfer at speeds of up to 4 Mbps.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Glossary-8  
Glossary  
K
K: Taken from the Greek word kilo, meaning 1000; often used as equivalent  
to 1024, or 2 raised to the 10th power. See also byte and kilobyte.  
keyboard: An input device containing switches that are activated by  
manually pressing marked keys. Each keystroke activates a switch  
that transmits a specific code to the computer. For each key, the  
transmitted code is, in turn, representative of the (ASCII) character  
marked on the key.  
kilobyte (KB): A unit of data storage equal to 1024 bytes. See also byte  
and megabyte.  
L
L1 cache: Level one cache. Memory cache built into the processor to help  
improve processing speed. See also cache memory, L2 cache.  
L2 cache: Memory cache installed on the motherboard to help improve  
processing speed. It is slower than L1 cache and faster than main  
memory. See also cache memory, L1 cache.  
LAN: A group of computers or other devices dispersed over a relatively  
limited area and connected by a communications link that enables  
any device to interact with any other on the network.  
Light Emitting Diode (LED): A semiconductor device that emits light when  
a current is applied.  
Liquid Crystal Display (LCD): Liquid crystal sealed between two sheets of  
glass coated with transparent conducting material. The viewing-side  
coating is etched into character-forming segments with leads that  
extend to the edge of the glass. Applying a voltage between the  
glass sheets alters the brightness of the liquid crystal.  
M
main board: See motherboard.  
megabyte (MB): A unit of data storage equal to 1024 kilobytes. See also  
kilobyte.  
megahertz: A unit of wave frequency that equals 1 million cycles per  
second. See also hertz.  
memory: Typically refers to the computer's main memory, where programs  
are run and data is temporarily stored and processed.  
Memory can be volatile and hold data temporarily, such as RAM, or  
it can be nonvolatile and hold data permanently, such as ROM. A  
computer's main memory is RAM. See RAM, ROM.  
menu: A software interface that displays a list of options on the screen.  
Also called a screen.  
microprocessor: A hardware component contained in a single integrated  
circuit that carries out instructions. Also called the central  
processing unit (CPU), one of the main parts of the computer.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Glossary-9  
Glossary  
mode: A method of operation, for example, the Shut Down Mode, Sleep  
Mode or the Hibernation Mode.  
modem: Derived from modulator/demodulator, a device that converts  
(modulates) digital data for transmission over telephone lines and  
then converts modulated data (demodulates) to digital format where  
received.  
monitor: A device that uses rows and columns of pixels to display  
alphanumeric characters or graphic images. See also CRT.  
motherboard: A name sometimes used to refer to the main printed circuit  
board in processing equipment. It usually contains integrated  
circuits that perform the processor’s basic functions and provides  
connectors for adding other boards that perform special functions.  
MP3: An audio compression standard that enables high-quality  
transmission and real-time playback of sound files.  
N
network: A collection of computers and associated devices that are  
connected by communications facilities. A network allows you to  
share data and peripheral devices, such as printers, with other  
users and to exchange electronic mail.  
non-system disk: A disk for storing programs and data that cannot be  
used to start the computer. Compare system disk.  
nonvolatile memory: Memory, usually read-only (ROM), that is capable of  
permanently storing information. Turning the computer’s power off  
does not alter data stored in nonvolatile memory.  
numeric keypad overlay: A feature that allows you to use certain keys on  
the keyboard to perform numeric entry, or to control cursor and page  
movement.  
O
OCR: Optical Character Recognition (reader). A technique or device that  
uses laser or visible light to identify characters and input them into a  
storage device.  
online state: A functional state of a peripheral device when it is ready to  
receive or transmit data.  
operating system: A group of programs that controls the basic operation  
of a computer. Operating system functions include interpreting  
programs, creating data files, and controlling the transmission and  
receipt (input/output) of data to and from memory and peripheral  
device.  
output: The results of a computer operation. Output commonly indicates  
data 1) printed on paper, 2) displayed at a terminal, 3) sent through  
the serial port of internal modem, or 4) stored on some magnetic  
media.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Glossary-10  
Glossary  
P
PAL: PAL (Phase Alternating Line) is the dominant video and broadcasting  
standard in Europe.  
parity: 1) The symmetrical relationship between two parameter values  
(integers) both of which are either on or off; odd or even; 0 or 1. 2) In  
serial communications, an error detection bit that is added to a  
group of data bits making the sum of the bits even or odd. Parity can  
be set to none, odd, or even.  
password: A unique string of characters used to identify a specific user.  
The computer provides various levels of password protection such  
as user and supervisor.  
PCI: Peripheral Component Interconnect. An industry standard 32-bit bus.  
peripheral: Any device, such as a printer or joystick, that is attached to the  
computer and controlled by the computer's CPU.  
Péritel: Péritel is a 21-pin connecting cable/port system that allows images  
and high-quality stereo sound (including Dolby® Pro-Logic sound  
formats) to be sent from one audio-visual device to another. It is also  
known as a "SCART connector" or "Euro connector".  
pixel: A picture element. The smallest dot that can be made on a display or  
printer. Also called a pel.  
plug and play: A capability with Windows that enables the system to  
automatically recognize connections of external devices and make  
the necessary configurations in the computer.  
pointing device: Any device, such as the TouchPad or a mouse, that  
enables you to move the cursor on the screen.  
port: The electrical connection through which the computer sends and  
receives data to and from devices or other computers.  
Power Saver: A TOSHIBA utility that lets you set the parameters for  
various power-saving functions.  
program: A set of instructions a computer can execute that enables it to  
achieve a desired result. See also application.  
prompt: A message the computer provides indicating it is ready for or  
requires information or an action from you.  
R
Radio frequency interference (RFI) shield: A metal shield enclosing the  
printed circuit boards of the printer or computer to prevent radio and  
TV interference. All computer equipment generates radio frequency  
signals. The FCC regulates the amount of signals a computing  
device can allow past its shielding. A Class A device is sufficient for  
office use. Class B provides a more stringent classification for home  
equipment use. TOSHIBA portable computers comply with Class B  
computing device regulations.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Glossary-11  
Glossary  
Random Access Memory (RAM): Volatile memory that can be written to  
as well as read. Volatile here means that information in RAM is lost  
when you turn off your computer. This type of memory is used for  
your computer's main memory. See also memory. Compare ROM.  
resolution: A measure of the sharpness of the images that can be  
produced by a printer or displayed on a screen. For a printer,  
resolution is expressed in dots per inch (dpi). For a screen, it is  
expressed as the number of pixels available horizontally and  
vertically  
restart: Resetting a computer without turning it off (also called "warm boot",  
"soft reset" or "reboot"). See also boot.  
RGB: Red, green and blue. A device that uses three input signals, each  
activating an electron gun for a primary additive color (red, green  
and blue) or port for using such a device. See also CRT.  
RJ11: A modular telephone jack.  
RJ45: A modular LAN jack.  
Read Only Memory (ROM): Non-volatile memory that can be read but not  
written to. Non-volatile here means that information in ROM remains  
whether or not the computer is receiving power. This type of  
memory is used to store your computer's BIOS, which is essential  
instructions the computer reads when you start it up. See also  
BIOS, memory. Compare RAM.  
S
S/P DIF: A standard of digital interface for audio.  
SCSI: Small Computer System Interface is an industry standard interface  
for connection of a variety of peripheral devices.  
SD/SDHC memory card: Secure Digital cards are flash memory widely  
used in a variety of digital devices such as digital cameras and  
Personal Digital Assistants.  
SECAM L: SECAM (Sequential Color Memory) is a broadcasting standard  
used in France.  
SIO: Serial Input/Output. The electronic methodology used in serial data  
transmission.  
soft key: Key combinations that emulate keys on the IBM keyboard,  
change some configuration options, stop program execution, and  
access the numeric keypad overlay.  
software: The set of programs, procedures and related documentation  
associated with a computer system. Specifically refers to computer  
programs that direct and control the computer system's activities.  
See also hardware.  
stop bit: One or more bits of a byte that follow the transmitted character or  
group codes in asynchronous serial communications.  
synchronous: Having a constant time interval between successive bits,  
characters or events.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Glossary-12  
Glossary  
system disk: A diskette that contains the operating system files needed to  
start the computer. Any diskette can be formatted as a system disk.  
A system disk is also called a "bootable disk", "boot disk" or a  
"startup disk." Compare non-system disk.  
T
telephony: the transmission of speech or sounds between two distant  
points with or without the use of wires, particularly a telephone.  
terminal: A typewriter-like keyboard and CRT display screen connected to  
the computer for data input/output.  
TFT display: A liquid crystal display (LCD) made from an array of liquid  
crystal cells using active-matrix technology with thin film transistor  
(TFT) to drive each cell.  
Touch Pad: A pointing device integrated into the TOSHIBA computer palm  
rest.  
U
USB: Universal Serial Bus. This serial interface lets you communicate with  
several devices connected in a chain to a single port on the  
computer.  
V
VGA: Video Graphics Array is an industry standard video adaptor that lets  
you run any popular software.  
volatile memory: Random access memory (RAM) that stores information  
as long as power is supplied to the computer.  
W
warm start: Restarting or resetting a computer without turning it off.  
Wi-Fi®: A registered trademark term of the Wi-Fi Alliance that stands for  
Wireless Fidelity, and is another term for the communication  
protocol to permit an Ethernet connection using wireless  
communication components.  
window: A portion of the screen that can display its own application,  
document or dialog box. Often used to mean a Windows window.  
Wireless LAN: Local Area Network (LAN) through wireless  
communication.  
write protection: A method for protecting a floppy diskette from accidental  
erasure.  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Glossary-13  
Index  
A
AC adaptor, 1-9  
DC IN indicator, 2-12, 6-3  
Display, 2-8  
additional, 1-18  
connecting, 3-2  
DC IN 19V jack, 2-5  
ASCII characters, 5-5  
automatic power off, 1-12  
brightness (down), 5-3  
brightness (up), 5-4  
controller, B-1  
hinge, 2-9  
opening, 3-5  
B
Battery  
charging, 6-5  
extending battery life, 6-8  
indicator, 2-12, 6-2  
Monitoring capacity, 6-7  
save mode, 1-13  
types, 6-3  
Equipment checklist, 1-1  
External monitor, 1-9, 2-3, 8-13  
Battery Charger, 8-9  
Battery pack, 1-9, 2-7  
additional, 8-9  
FN + 1 (TOSHIBA Zooming Utility  
reduce), 5-4  
FN + F1 (Lock), 5-3  
FN + F2 (Power Plan), 5-3  
FN + F3 (Sleep), 5-3  
FN + F4 (Hibernate), 5-3  
FN + F5 (Output), 5-3  
replacing, 6-9  
Bluetooth, 1-11, 4-35  
Bluetooth Stack for Windows by  
Toshiba, 1-15  
problems, 9-22  
Bridge media slot, 1-10, 2-2, 8-4  
indicator, 2-12  
using, 8-4  
FN + F6 (Brightness Down), 5-3  
FN + F7 (Brightness Up), 5-4  
FN + F8 (Wireless), 5-4  
FN + F9 (Touch Pad), 5-4  
FN + space (Zoom), 5-4  
Function buttons, 4-7  
C
Cache memory, 1-3  
Cleaning the computer, 4-39  
Cooling vents, 2-2, 2-7  
User’s Manual  
Index-1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Function keys, 5-2  
H
Hard disk drive, 2-7  
Heat dispersal, 1-13  
Hibernation Mode, 1-13  
Hot keys, 1-12  
disconnecting, 4-39  
jack, 2-3  
Brightness (Up), 5-4  
Hibernate, 5-3  
Lock, 5-3  
Mute, 5-3  
Output, 5-3  
Power Plan, 5-3  
Sleep, 5-3  
(enlarge), 5-4  
TOSHIBA Zooming Utility  
(reduce), 5-4  
expansion, 1-18  
connecting, 4-33  
disconnecting, 4-34  
jack, 2-4  
Touch Pad, 5-4  
Wireless, 5-4  
Zoom, 5-4  
properties menu, 4-32  
Moving the computer, 4-40  
MultiMediaCard  
problems, 9-14  
HW Setup  
accessing, 7-1  
general, 7-1  
HW Setup utility, 1-15  
I
Indicators  
Battery, 2-12, 6-2  
DC IN, 2-12  
HDD/ODD/eSATA, 2-12  
Power, 2-12  
inserting, 8-2  
problems, 9-12  
removing, 8-3  
Pointing device  
Touch Pad, 2-9, 4-1  
Ports, 1-9  
External monitor, 1-9  
USB, 1-9  
Power  
K
Keyboard, 1-9, 5-1  
emulating keys on enhanced, 5-2  
Function keys F1 ... F12, 5-2  
Hot keys, 5-3  
problems, 9-7  
Typewriter keys, 5-1  
Windows special keys, 5-5  
conditions, 6-1  
Hibernation Mode, 3-8  
User’s Manual  
Index-2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
indicator, 6-3  
panel power on/off, 6-12  
Sleep Mode, 3-10  
turning off, 3-8  
Recovery hard disk drive, 3-14  
Restarting the computer, 3-12  
turning on, 3-7  
SD/SDHC memory card, miniSD/  
Problems  
AC power, 9-5  
Analyzing the problem, 9-2  
Battery, 9-5  
Bluetooth, 9-22  
Sleep Mode, 1-14  
System automatic, 1-13  
External monitor, 9-20  
Hard disk drive, 9-9  
9-3  
HDMI Monitor, 9-23  
Internal display panel, 9-7  
Keyboard, 9-7  
LAN, 9-22  
Memory Stick/Memory Stick PRO,  
9-13  
emulating keys on enhanced  
Sound system, 1-10, 4-24  
Headphone (S/PDIF) jack, 1-10,  
microphone, 2-10  
microphone jack, 1-10, 2-3  
Stereo speakers, 2-9  
Modem, 9-21  
MultiMediaCard, 9-14  
Overheating power down, 9-4  
Password, 9-7  
PC Card, 9-12  
Pointing device, 9-14  
Power, 9-4  
microSD Card, 9-13  
Self test, 9-4  
TOSHIBA ConfigFree, 1-15  
TOSHIBA Disc Creator, 1-15, 4-14  
TOSHIBA PC Diagnostic Tool, 1-14  
TOSHIBA support, 9-23  
TOSHIBA Zooming Utility, 1-14  
using, 4-1  
Solid State Drive, 9-9  
Sound system, 9-19  
System start-up, 9-3  
TOSHIBA support, 9-23  
Touch Pad, 9-14  
USB device, 9-17  
USB floppy diskette drive, 9-12  
USB mouse, 9-16  
Wireless LAN, 9-22  
U
USB device, 1-9  
problems, 9-17  
USB floppy diskette drive, 8-10  
problems, 9-12  
using, 8-11  
V
Processor, 1-3  
Video RAM, 1-5  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Index-3  
W
Web Camera, 1-10  
Wireless communication, 4-34  
Wireless communication switch, 2-1  
Wireless LAN, 1-11, 4-34  
problems, 9-22  
User’s Manual  
Index-4  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Technicolor Thomson CRT Television 14MH10C User Manual
Technicolor Thomson CRT Television DF321C User Manual
The First Years Car Seat B500 User Manual
Topaz Systems Car Amplifier AM1 User Manual
Toshiba Cash Register MA 79 User Manual
TRENDnet Printer TEW MP1U User Manual
Uniden Security Camera UDRC14 User Manual
VeriFone Credit Card Machine 45506 User Manual
Viking Ventilation Hood DBCV3082 User Manual
Vizio TV DVD Combo VBR231 User Manual