TOSHIBA POS Terminal
ST-71 SERIES
Owner's Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Summary
EO1-12031
Safety Summary
Personal safety in handling or maintaining the equipment is extremely important. Warnings and Cautions
necessary for safe handling are included in this manual. All warnings and cautions contained in this manual
should be read and understood before handling or maintaining the equipment.
Do not attempt to effect repairs or modifications to this equipment. If a fault occurs that cannot be rectified
using the procedures described in this manual, turn off the power, unplug the machine, then contact your
authorized TOSHIBA TEC representative for assistance.
Meanings of Each Symbol
This symbol indicates warning items (including cautions).
Specific warning contents are drawn inside the symbol.
(The symbol on the left indicates a general caution.)
This symbol indicates prohibited actions (prohibited items).
Specific prohibited contents are drawn inside or near the symbol.
(The symbol on the left indicates “no disassembling”.)
This symbol indicates actions which must be performed.
Specific instructions are drawn inside or near the ꢀsymbol.
(The symbol on the left indicates “disconnect the power cord plug from the outlet”.)
This indicates that there is the risk of death or serious injury if the
machines are improperly handled contrary to this indication.
WARNING
Do not plug in or unplug the
power cord plug with wet
hands as this may cause
electric shock.
Do not use voltages other than the
voltage (AC) specified on the
rating plate, as this may cause fire
or electric shock.
Any other than the
specified AC voltage is
prohibited.
Prohibited
Prohibited
If the machines share the same
outlet with any other electrical
appliances that consume large
amounts of power, the voltage
will fluctuate widely each time
these appliances operate. Be
sure to provide an exclusive
outlet for the machine as this
may cause fire or electric
shock.
Do not place metal objects or
water-filled containers such as
flower vases, flower pots or mugs,
etc. on top of the machines. If
metal objects or spilled liquid enter
the machines, this may cause fire
or electric shock.
Prohibited
Do not insert or drop metal,
flammable or other foreign
objects into the machines
through the ventilation slits, as
this may cause fire or electric
shock.
Do not scratch, damage or modify
the power cords. Also, do not
place heavy objects on, pull on, or
excessively bend the cords, as this
may cause fire or electric shock.
Prohibited
Prohibited
If the machines are dropped or
their cabinets damaged, first
turn off the power switches and
disconnect the power cord
plugs from the outlet, and then
contact your authorized
TOSHIBA TEC representative
for assistance. Continued use
of the machine in that condition
may cause fire or electric
shock.
Continued use of the machines in
an abnormal condition such as
when the machines are producing
smoke or strange smells may cause
fire or electric shock. In these
cases, immediately turn off the
power switches and disconnect the
power cord plugs from the outlet.
Then, contact your authorized
TOSHIBA TEC representative for
assistance.
Disconnect
the plug.
Disconnect
the plug.
(i)
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Summary
EO1-12031
If foreign objects (metal
When unplugging the power cords,
be sure to hold and pull on the plug
portion. Pulling on the cord portion
may cut or expose the internal wires
and cause fire or electric shock.
Disconnect
the plug.
Disconnect
fragments, water, liquids) enter
the machines, first turn off the
power switches and disconnect
the power cord plugs from the
outlet, and then contact your
authorized TOSHIBA TEC
representative for assistance.
Continued use of the machine in
that condition may cause fire or
electric shock.
the plug.
Ensure that the equipment is
properly grounded. Extension
cables should also be grounded.
Fire or electric shock could
occur on improperly grounded
equipment.
Do not remove covers, repair or
modify the machine by yourself.
You may be injured by high
voltage, very hot parts or sharp
edges inside the machine.
Unauthorized modification is
prohibited.
Connect a
No
disassembling.
grounding wire.
This indicates that there is the risk of personal Injury or damage to objects if
the machines are improperly handled contrary to this indication.
CAUTION
Precautions
The following precautions will help to ensure that this machine will continue to function correctly.
ꢀ
Try to avoid locations that have the following adverse conditions:
* Temperatures out of the specification
* Shared power source
Do not subject the machine to sudden shocks.
* Direct sunlight
* High humidity
* Dust/Gas
* Excessive vibration
ꢀ
ꢀ
ꢀ
Do not press the keys too hard. Keys will operate correctly if they are touched lightly.
Clean the cover and keyboard, etc. by wiping with a dry cloth or a cloth soaked with detergent and
wrung out thoroughly. Never use thinner or other volatile solvent for cleaning.
At the end of the day, turn the power OFF, then clean and inspect the exterior of the machine.
Try to avoid using this equipment on the same power supply as high voltage equipment or equipment
likely to cause mains interference.
USE ONLY TOSHIBA TEC SPECIFIED consumables.
DO NOT STORE the consumables where they might be exposed to direct sunlight, high temperatures, high
humidity, dust, or gas.
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
When moving the machine, take hold of the drawer and lift the machine.
Do not place heavy objects on top of the machines, as these items may become unbalanced and fall
causing injury.
Do not block the ventilation slits of the machines, as this will cause heat to build up inside the
machines and may cause fire.
Do not lean against the machine. It may fall on you and could cause injury.
Place the machine on a stable and level surface.
ꢀ
ꢀ
ꢀ
Request Regarding Maintenance
ꢀ
Utilize our maintenance services.
After purchasing the machine, contact your authorized TOSHIBA TEC representative for assistancii
once a year to have the inside of the machine cleaned. Otherwise, dust will build up inside the
machines and may cause a fire or a malfunction. Cleaning is particularly effective before humid rainy
seasons.
Our preventive maintenance service performs the periodic checks and other work required to maintain
the quality and performance of the machines, preventing accidents beforehand.
For details, please consult your authorized TOSHIBA TEC representative for assistance.
Using insecticides and other chemicals
Do not expose the machines to insecticides or other volatile solvents. This will cause the cabinet or
other parts to deteriorate or cause the paint to peel.
ꢀ
ꢀ
(ii)
Download from Www.Somanuals.com. All Manuals Search And Download.
EO1-12031
TABLE OF CONTENTS
Page
1. INTRODUCTION----------------------------------------------------------------------------------------1- 1
1.1 Accessories--------------------------------------------------------------------------------------------------1- 1
2. APPEARANCE------------------------------------------------------------------------------------------2- 1
2.1 Standard Model---------------------------------------------------------------------------------------------2- 1
2.2 Available Options-------------------------------------------------------------------------------------------2- 3
2.3 Example of POS Terminal with Some Options -----------------------------------------------------2- 3
3. CONNECTORS -----------------------------------------------------------------------------------------3- 1
4. INSTALLATION PROCEDURE---------------------------------------------------------------------4- 1
4.1 Environment for Installation------------------------------------------------------------------------------4- 1
4.2 Connecting the AC Plug----------------------------------------------------------------------------------4- 2
5. ADJUSTMENT ------------------------------------------------------------------------------------------5- 1
5.1 Tilt Angle Adjustment--------------------------------------------------------------------------------------5- 1
5.2 Brightness Adjustment------------------------------------------------------------------------------------5- 2
5.3 Speaker Volume Adjustment----------------------------------------------------------------------------5- 2
5.4 Beep Volume Adjustment -------------------------------------------------------------------------------5- 2
6. MAGNETIC CARD READER (OPTION) ---------------------------------------------------------6- 1
6.1 How to Read Magnetic Card ----------------------------------------------------------------------------6- 1
7. iBUTTON® (OPTION)----------------------------------------------------------------------------------7- 1
7.1 How to Read iButton --------------------------------------------------------------------------------------7- 1
8. GENERAL MAINTENANCE -------------------------------------------------------------------------8- 1
8.1 Cleaning ------------------------------------------------------------------------------------------------------8- 1
9. TROUBLESHOOTING --------------------------------------------------------------------------------9- 1
10. SPECIFICATIONS ----------------------------------------------------------------------------------- 10- 1
10.1 Basic Specifications ------------------------------------------------------------------------------------- 10- 1
10.2 Options------------------------------------------------------------------------------------------------------ 10- 3
CAUTION!
1. This manual may not be copied in whole or in part without prior written permission of
TOSHIBA TEC.
2. The contents of this manual may be changed without notification.
3. Please refer to your local Authorised Service representative with regard to any queries you
may have in this manual.
Download from Www.Somanuals.com. All Manuals Search And Download.
1. INTRODUCTION
EO1-12031
1.1 Accessories
1. INTRODUCTION
Thank you for choosing the TOSHIBA POS Terminal. This POS terminal contains all the high
performance register functions necessary for a specialty store POS terminal and enables the user
oriented system configuration.
The operation panel can be chosen from 12-inch TFT display and 15-inch TFT display.
This manual describes the functions and handling of this POS terminal and should be read carefully to
help gain maximum performance and life from your POS terminal. For most queries please refer to
this manual and keep it safe for future reference.
1.1 Accessories
Confirm that all the following accessories are contained in the carton. If any accessories are missing
or damaged, contact your TOSHIBA TEC service representative.
Owner’s Manual (1 copy)
Bind Screw M-3x3
(8 pcs.)
1- 1
Download from Www.Somanuals.com. All Manuals Search And Download.
2. APPEARANCE
EO1-12031
2.1 Standard Model
2. APPEARANCE
2.1 Standard Model
12-inch display POS terminal
MIC IN
Beep Volume
12” TFT Color Display
with Touch Panel
Reset Switch
Power Switch
Speaker Volume
HDD LED (Yellow)
Power LED (Green)
Speaker
Brightness Control
15-inch display POS terminal
Beep Volume
MIC IN
15” TFT Color Display
with Touch Panel
Reset Switch
Power Switch
Speaker Volume
Speaker
HDD LED (Yellow)
Power LED (Green)
Brightness Control
2- 1
Download from Www.Somanuals.com. All Manuals Search And Download.
2. APPEARANCE
EO1-12031
2.1 Standard Model
1) Power LED (Green)
This is the LED to indicate the power ON/OFF status of the POS terminal. The green LED is illuminated
when the power is ON.
2) HDD LED (Yellow)
The yellow LED is illuminated during the access to the hard disk drive.
3) Power Switch
This is the switch to turn the power of the POS terminal ON or OFF.
4) Reset Switch
This switch is used to reset the unit when the POS terminal hangs up.
CAUTION!
Do not press the Reset Switch unnecessarily. Doing so may cause an error.
5) Speaker Volume
This is used to adjust the internal speaker volume.
6) MIC IN
This connector is used to connect a monophonic microphone via the mono mini jack terminal.
7) Beep Volume
This is used to adjust the internal beep speaker volume.
8) Brightness Control
This is used to adjust the brightness of the operator’s display.
2- 2
Download from Www.Somanuals.com. All Manuals Search And Download.
2. APPEARANCE
EO1-12031
2.2 Available Options
2.2 Available Options
15" 2nd Display
12" 2nd Display
PCMCIA/CF Board
LIU
LVDS PC Board
LIU Stand
Pole Unit
12" or 15" POS Terminal
Relay PC Board
iButton Unit
MCR
COM 5 or 6
2.3 Examples of POS Terminal with Some Options
• Example of ST-71 with an optional
MCR and 2nd display
• Example of ST-71 with an optional MCR,
iButton, and 2nd display
MCR Unit
(Option)
2nd display
(Option)
2nd Display
(Option)
MCR Unit
(Option)
MCR Unit (Option)
(When attached to
the left side of the
display)
iButton (Option)
• Example of ST-71 with an optional LIU
(Front display: 12/15-inch TFT, Rear display: LIU + LIU stand)
• Example of ST-71 with an optional LIU
(Front display: 12/15-inch TFT, Rear display: LIU + Pole unit + LIU stand)
LIU (Option)
LIU (Option)
Pole Unit (Option)
LIU Stand (Option)
LIU Stand (Option)
2- 3
Download from Www.Somanuals.com. All Manuals Search And Download.
2. APPEARANCE
EO1-12031
2.3 Examples of POS Terminal with Some Options
CAUTION!
Do not strongly push or scratch the edge of the touch screen (the shaded part of the following figure)
with a sharp tool, such as a nail and a pen. Doing this may damage the touch panel.
4 mm
4 mm
2- 4
Download from Www.Somanuals.com. All Manuals Search And Download.
3. CONNECTORS
EO1-12031
3. CONNECTORS
3. CONNECTORS
AC Inlet
LVDS1
LVDS2*
PS/2 Mouse
USB5
COM6*
COM5*
P-USB3
PCMCIA*
CF Card*
24V DC
outlet
COM1
Display Power
and Signal
COM2
COM3
Line Out
USB4
LAN
DRW2
DRW1
LPT
PS/2 Keyboard
COM4
VGA
*: Option
Connector
Description
AC inlet
A connector for the AC inlet
24V DC outlet
A terminal of a DC 24V line to which the power cable of the Receipt/Journal
printer is connected.
PS/2 (Mouse, Keyboard)
Mini-DIN 6-pin female type connector
Connector for the PS/2 type mouse, Connector for the PS/2 type keyboard
Connector for the USB (Universal Serial Bus) interface USB V2.0/1.1 and UHCI
(conforming to Universal Hub Controller Interface V2.0/1.1)
NOTE: USB functions may not be supported depending on the Operating
System.
USB3 (USB supplied with
power)
USB4,5 (General 5V USB)
USB3 is a USB socket supplied with power, which is 1 port of 24V USB. USB4
and USB5 can be used as general 5V USB connectors.
Modular type connector for the 10BASE-T/100BASE-TX LAN interface
A 24V type drawer is connectable.
Expandable LCD interface (LVDS2 is a option.)
Expandable VGA interface
LAN
DRW1, DRW2
LVDS1, 2
VGA
15-pin VGA female type connector
COM1, 2
D-sub 9-pin male type connector (without power)
A slot scanner, modem, serial interface type scale, EFT, etc. are connectable.
D-sub 9-pin female type connector (with +5V, +12V output)
A line display unit or RS-232C type hand scanner is connectable.
NOTES:
COM3, 4, 5, 6
1. COM4 cannot be used when the touch panel TFT is connected to the POS
terminal.
2. When an optional back indicator unit is installed on the POS terminal, COM3
is not available.
3. COM5 and COM6 are available only when the optional kit is installed.
LPT1
D-sub 25-pin female connector
Printer, etc. having a Centronics interface or equivalent are connectable.
Used for connecting an external speaker via the stereo mini jack terminal
TYPE II compact flash card conforming to CFA (Compact Flash Association)
standard can be used.
Line-out
CF Card interface slot
PC Card interface slot
This complies with PC Card Standard Release 8.0.
32-bit Card Bus card and 16-bit PC card are supported. One slot is provided and
accepts up to TYPE II card.
3- 1
Download from Www.Somanuals.com. All Manuals Search And Download.
4. INSTALLATION PROCEDURE
EO1-12031
4.1 Environment for Installation
4. INSTALLATION PROCEDURE
WARNING!
1. Care must be taken not to get your fingers caught between the LCD Frame and the POS terminal
when bending the display backward.
2. DO NOT raise the LCD Frame while the Front Cover is not in position. When the LCD Frame is raised
at right angle (90°) or more, the LCD may fall under its own weight, and your fingers may be caught.
CAUTION!
When removing the protective film from the display surface, please be sure to do it slowly. If it is done
quickly, static electricity may generate, and the TFT may be damaged.
4.1 Environment for Installation
CAUTION!
When installing the POS terminal, take the following precautions. Failure to do this may cause fire,
electric shock, or injury.
1. Avoid locations where it is subject to the following:
•
•
•
•
•
Direct sunlight
High temperature, high humidity
Rapid change in temperature
Excessive vibration
Dust
2. Keep away from any devices that emit magnetism or electromagnetic wave.
3. Keep away from flame or moisture.
4. Be sure to place the POS terminal on a level and stable surface.
1. Place the POS terminal on a level surface.
2. Provide a minimum space to the left, right, front and rear of the POS terminal for proper cooling. (The
unit has air vents and a fan on the front and left. Spaces should be provided to prevent the air vents
from being blocked and the air flow from being obstructed.)
80 mm
(See NOTE.)
80 mm
80 mm
See NOTE.
80 mm
NOTE: A fan is provided on these sides. Do not prevent the ventilation of the fan.
4- 1
Download from Www.Somanuals.com. All Manuals Search And Download.
4. INSTALLATION PROCEDURE
EO1-12031
4.2 Connecting the AC Plug
4.2 Connecting the AC Plug
NOTE: Since the power cord set is not supplied with this unit, please purchase an approved one that meets the
following standard from your authorized TOSHIBA TEC representative.
1. Gently bend the Display backward by the both sides of the LCD Frame.
LCD Frame
2. Remove the two screws that secure the Front Cover. Press the center of the Front Cover’s top to
release the hook, and pull out the Front Cover.
PUSH
Hook
Screw
Front Cover
Screw
4- 2
Download from Www.Somanuals.com. All Manuals Search And Download.
4. INSTALLATION PROCEDURE
EO1-12031
4.2 Connecting the AC Plug
3. Fully insert the Power Cord Plug into the Inlet of the POS terminal.
Inlet
Power Cord Plug
4. Fit the Front Cover into the front of the POS terminal, and secure it with the two screws.
Screw
Front Cover
Screw
4- 3
Download from Www.Somanuals.com. All Manuals Search And Download.
5. ADJUSTMENT
EO1-12031
5.1 Tilt Angle Adjustment
5. ADJUSTMENT
Tilt angle and brightness of the operator’s display can be adjusted.
Adjustment method is common to both of 12-inch display model and 15-inch display model.
CAUTION!
1. Do not adjust the display angle by holding the LCD panel. Doing so may damage the unit. Be
sure to hold the LCD frame.
2. Care must be taken not to catch your fingers between POS terminal and the LCD Frame when
bending the display backward.
5.1 Tilt Angle Adjustment
The tilt angle of the operator’s display can be adjusted freely in a range of 0° to 90°.
Hold both sides of the LCD frame, and slowly push the display backward to your best angle.
<Single display type (Standard)>
0° to 90°
LCD Frame
<Dual display type (Option)>
0° to 90°
0° to 90°
5- 1
Download from Www.Somanuals.com. All Manuals Search And Download.
5. ADJUSTMENT
EO1-12031
5.2 Brightness Adjustment
The angle of the optional LIU is also adjustable as follows.
0° to 45°
0° to 145°
(in both directions)
<Tilt range>
<Swivel range>
5.2 Brightness Adjustment
The brightness control is provided on the lower right of the operator’s display.
Turning it to the left makes the display darker, and turning it to the right makes the display brighter.
Darke
r
Brightness Control
Brighter
5.3 Speaker Volume Adjustment
When it is turned counterclockwise, the sound volume turns up.
When it is turned clockwise, the sound volume turns down.
5.4 Beep Volume Adjsutment
When it is turned counterclockwise, the sound volume turns up.
When it is turned clockwise, the sound volume turns down.
Beep Volume
Speaker Volume
5- 2
Download from Www.Somanuals.com. All Manuals Search And Download.
6. MAGNETIC CARD READER (OPTION)
EO1-12031
6.1 How to Read Magnetic Card
6. MAGNETIC CARD READER (OPTION)
The optional magnetic card reader can be installed on either side of the POS terminal.
6.1 How to Read Magnetic Card
Insert the magnetic card into the upper portion of the magnetic card reader slot and slowly move the card
downward.
Magnetic Card
MCR Unit (Option)
NOTE: Moving the magnetic card too fast or too slowly may cause a read error.
6- 1
Download from Www.Somanuals.com. All Manuals Search And Download.
7. iBUTTON® (OPTION)
EO1-12031
7.1 How to Read iButton
7. iBUTTON® (OPTION)
The optional iButton unit can be installed on the bottom of the LCD.
7.1 How to Read iButton
CAUTION!
1. Keep storage media, like a floppy disk, away from the touch probe. The stored data may be
destroyed by the magnet of the touch probe.
2. Keep a metal object like a paper clip away from the touch probe. If such an object is attached to the
touch probe, it may cause a short-circuit.
Data stored in an iButton can be read by attaching the iButton key to the touch probe. The iButton key is
held by the magnet of the touch probe.
iButton Unit
(Option)
iButton Key
Touch Probe
7- 1
Download from Www.Somanuals.com. All Manuals Search And Download.
8. GENERAL MAINTENANCE
EO1-12031
8.1 Cleaning
8. GENERAL MAINTENANCE
8.1 Cleaning
WARNING!
1. Be sure to disconnect the power cord prior to performing any maintenance.
2. Do not pour water directly on or wipe the operator’s display with a soaked cloth, as this may cause
fire, electric shock, or machine failure.
CAUTION!
1. Never use an organic solvent like thinners or benzene for cleaning. Using such solvents may
discolor the covers.
2. Do not use any sharp object to clean the operator’s display. Doing so may cause an operator’s
display failure.
3. Do not insert the nozzle of an air blower into the magnetic card reader slot. Doing so may
damage the scanning head, resulting in the magnetic card reader failure.
To help retain the high quality and performance of your POS Terminal, it should be cleaned regularly. The
greater the usage on the POS Terminal, the more frequent the cleaning. (i.e. low usage = weekly: high
usage = daily)
• Cleaning the Operator’s Display
Clean the surface of the operator’s display with a soft dry cloth or with an electrostatic free cleaner for
automated office equipment.
• Cleaning the Covers
Wipe the covers with a soft dry cloth or soft cloth slightly moistened with mild detergent. After using
detergent for cleaning, be sure to wipe it off with a slightly moistened cloth.
8- 1
Download from Www.Somanuals.com. All Manuals Search And Download.
9. TROUBLESHOOTING
EO1-12031
9. TROUBLESHOOTING
9. TROUBLESHOOTING
WARNING!
If you cannot solve a problem with the following solutions, do not attempt to repair it by yourself. Turn
the power off, unplug the POS Terminal, then contact the nearest TOSHIBA TEC service
representative for assistance.
Symptom
Check point
Solution
The power does not • Is the power cord plugged in correctly?
• Plug in correctly.
turn on.
• Is the power supplied to the AC outlet?
• If it is not a power failure,
check for the power supply to
the AC outlet with another
electric appliance.
When the power is not
supplied, contact your
nearest power company.
• Check the circuit breaker.
• Refer to Section 5
Adjustment and adjust the
display angle.
• Refer to Section 5
Adjustment and adjust the
brightness properly.
• Has the circuit breaker blown?
• Does the operator’s display reflect
sunlight or room light?
• Is the tilt angle adjusted properly?
• Is the brightness adjusted properly?
The operator’s
display is hard to see.
Magnetic card reader • Does the used card comply with the
• Use Track 1, 2 complying
with ISO.
does comply-not
read the data.
standard?
• Was the card moved too fast or too
slowly?
• Move the card at the proper
speed. (10~150 cm/sec.)
• Insert the card so that the
magnetic strip faces the
scanning head.
• Is the card reading direction correct?
9- 1
Download from Www.Somanuals.com. All Manuals Search And Download.
10. SPECIFICATIONS
EO1-12031
10.1 Basic Specifications
10. SPECIFICATIONS
10.1 Basic Specifications
Item
Description
Input voltage
AC 100V-240V +10%, -10% 50/60Hz 5.0A (115V)-2.5A (230V)
DC24V +5%, -5%
DC output voltage
Operating temperature
Relative humidity
5°C to 35°C
10% to 80%RH (no condensation)
Dimensions
15-inch LCD 359.9 mm (W) x 388.1 mm (D) x 371.4 mm (H)
12-inch LCD 295.0 mm (W) x 386.8 mm (D) x 323.5 mm (H)
15-inch LCD 12.5 Kg
Weight
12-inch LCD 11.5 Kg
Power cord
A power cord is not included in this product. Please use one complied with
each country’s safety standard. For details, please contact the nearest
TOSHIBA TEC service representative.
CPU
Intel Celeron® 2.0 GHz with 128 KB secondary cache
BIOS ROM
RAM
1MB Flash ROM
Capacity
Type
Standard 256MB (Max. 2GB)
Max. 1GB/slot can be equipped.
DDR SDRAM PC2100/2700, 2.5V unbuffered type, ECC/non ECC 184-pin
DDR SDRAM DIMM connector, 2 slots installed
Interface
RS-232C x 6 (Standard: 4 + Option: 2), Parallel x 1, P-USB x 1, USB x 2,
Drawer x 2 (24V type), PS/2 x 2, 24VDC OUT (DIN 3-pin) x 1
Display interface
LCD Interface
Touch panel method
Hard Disk Drive (HDD)
LAN interface
PC card
VGA x 1 channel (on-board, standard)
Standard LVDS1 x 1, LVDS1 + LVDS2 (Option)
Analog resistor film
Max. 2 units of 2.5-inch HDD (option) can be connected.
10 BASE-T, 100 BASE-TX (Wake on LAN support)
PCMCIA TYPE II x 1 (option)
CF card
CF card TYPE II x 1 (option)
MCR
ISO-1,2-track one-sided type (option)
Sound generator
AC97 interface; LINE OUT x 1, MIC IN x 1, Built-in speaker (Monaural
sound)
Support OS
Windows 2000, Windows XP, Certified Linux
10- 1
Download from Www.Somanuals.com. All Manuals Search And Download.
10. SPECIFICATIONS
EO1-12031
10.1 Basic Specifications
Item
Description
12-inch display
15-inch display
Operator’s Display type
Display
12.1-inch color TFT with touch
panel
15.0-inch color TFT with touch
panel
Display size
12.1-inch 800 x 600 dots
262K color (262,144 colors)
320 cd/m2 320 nit
15.0-inch 1024 x 768 dots
262K color (262,144 colors)
280 cd/m2 280 nit
Number of colors
Brightness
Display area
Dot size
246 mm (W) x 184.5 mm (H)
0.3075 mm (W) x 0.3075 mm (H)
304.1 mm (W) x 228.1 mm (H)
0.297 mm (W) x 0.297 mm (H)
Touch panel
Analog Resistor Film
(1024 x 1024 dots)
Analog Resistor Film
(1024 x 1024 dots)
Adjustment
mechanism
Brightness volume (TFT) and Tilt angle (Free adjustment in a range of
0° to 90°)
No swivel adjustment
LIU
Number of displayed 5 x 7 dot fluorescent display 20 digits x 2 lines
(Option)
characters
20 triangles under the 2nd line
Display color
Blue
Display
area/character size
Character size: 5.5 mm (W) x 10.5 mm (H)
Character pitch: 7.4 mm (W) x 15.5 mm (H)
Type font
182 types of half width ANK
Display angle
Tilt: 0° to 45° (9 step, 5deg, each)
Swivel: 0° to 145° (in both directions)
Interface with
ENGINE
RS-232C interface (with power)
10- 2
Download from Www.Somanuals.com. All Manuals Search And Download.
10. SPECIFICATIONS
EO1-12031
10.2 Options
10.2 Options
Option name
Model
Description
24V-drive standard drawer
(with screw holes on the left and the rear for installing the
POLST-51)
Dimensions and Weight:
DRWST-51A-4MVK-QM-R
DRWST-51A-8MVK-QM-R
460(W) x 400(D) x 115(H) mm, 10 Kg
Money Case Type: MC4,8
Drawer unit
Type
Bill holder Coin tray Mini coin case CDC
Remarks
Drawer type
4MVK-QM
8MVK-QM
5
4
5
6
No
1
Yes With media slot
Yes With media slot
12.1-inch TFT color display to be installed onto the POS
terminal
TFTST-71-2A-QM-R
TFTST-71-5A-QM-R
KIT-71-DSP1-QM-R
LIUST-71-BAAK-QM-R
2nd display unit
LVDS board
15.1-inch TFT color display to be installed onto the POS
terminal
Used to connect a TFTST-71 optional 2nd display unit.
Line indicator unit
(LIU)
20 characters x 2 lines dot display to be installed onto the
POS terminal
Pole and extension cable for attaching an LIUST-71 optional
line indicator unit at the level of 235 mm from the standard
position
Pole unit
KIT-71-POLE-QM-R
A stand for installing an LIUST-71 optional line indicator unit
onto the POS terminal
LIU stand
KIT-71-BASE-QM-R
TRST-56-P-1K-QM-R
TRST-56-S-1K-QM-R
Parallel interface single thermal printer for 80 mm wide paper
Cabinet color: Cool Black
Printer unit
Serial interface single thermal printer for 80 mm wide paper
Cabinet color: Cool Black
PC card/CF card interface kit
This kit conforms to the 32-bit CardBus (Card-32) card and
the 16-bit PC card (Card-16).
A slot is provided on the board, which supports up to
PCMCIA Type II or CF card TYPE II.
PCMCIA/CF
interface board
MIFST-71-2-QM
COM5 and COM6
connectors
KIT-71-COM-QM-R
MCRST-71-3-QM-R
KIT-71-BTN1-QM-R
KIT-71-RELY-QM-R
COM5 or COM6 connector and cable kit
Magnetic card
reader (MCR)
ISO Track 1 and 2 type magnetic card reader kit
iButton unit to be installed onto the POS terminal
(An iButton key is not included.)
iButton
Relay PC board
Used to control an optional MCR unit or iButton unit.
NOTE:
Model names that end with "-R" are RoHS compliant models. If "-R" is not attached, that model is non RoHS
compliant.
Never install non RoHS compliant optional equipment or parts on a RoHS compliant machine which is supposed
to be used in the countries that enforce the RoHS directive, as doing this is legally prohibited.
10- 3
Download from Www.Somanuals.com. All Manuals Search And Download.
English
Waste Recycling information for users:
Following information is only for EU-member states:
The crossed out wheeled bin symbol is used to indicate that the product must not be treated as general household waste.
By ensuring that this product is disposed of correctly you will be helping to prevent potentially negative consequences for
the environment and human health, which could otherwise be caused by incorrect waste handling of this product.
For more detailed information about the take-back and recycling of this equipment, please contact the supplier that
provided you with the product in question.
French
Information aux utilisateurs concernant le recyclage des déchets:
Les informations suivantes sont uniquement destinées aux pays membres de l’Union Européenne:
L’utilisation du symbole de "poubelle à roulettes barrée" indique que ce produit ne doit pas être traité comme un déchet
ménager classique.
En vous assurant que ce produit est correctement mis au rebut, vous participerez à la prévention de l’environnement et
de la santé publique, contre des conséquences négatives potentielles qui pourraient résulter d’un traitement inapproprié
des déchets de ce produit. Pour obtenir des informations complémentaires concernant la récupération et le recyclage de
ce produit, veuillez contacter le fournisseur auprès duquel vous avez acheté le produit.
German
Wiederverwertungsinformationen für Verbraucher:
Die folgenden Informationen gelten nur für EU-Mitgliedsstaaten:
Das durchgestrichene Mülltonnensymbol weist darauf hin, dass dieses Produkt nicht wie allgemeiner Haushaltsmüll
behandelt werden darf.
Indem Sie aktiv mitwirken, dieses Produkt ordnungsgemäß zu entsorgen, helfen Sie mit, mögliche negative
Auswirkungen auf die Umwelt sowie die menschliche Gesundheit zu vermeiden, die sonst durch die unsachgemäße
Entsorgung dieses Produktes beeinträchtigt werden könnten.
Für nährere Informationen zur Rücknahme und Wiederverwertung dieses Produktes wenden sie sich bitte an den
Lieferanten, von dem Sie dieses Produkt erworben haben.
Spanish
Información para usuarios sobre el reciclaje de residuos:
La siguiente información sólo concierne a los Estados Miembros de la UE:
El uso del símbolo de un contenedor con ruedas tachado indica que este producto no puede ser tratado como si fuera
un residuo doméstico.
Asegurando que nos deshacemos de este producto de forma correcta, ayudaremos a evitar potenciales consecuencias
negativas tanto para el medio ambiente como para la salud pública, que podrían producirse debido a un tratamiento
inapropiado de este producto. Para obtener una información más detallada sobre la recogida y reciclaje de su producto,
por favor, póngase en contacto con el proveedor donde lo compró.
Dutch
Gebruikersinformatie over het recycleren van afval:
De volgende informatie geldt enkel in EU-lidstaten:
Het symbool met de doorkruiste afvalbak geeft aan dat dit product niet mag worden behandeld als algemeen
huishoudelijk af val.
Door dit product op de juiste manier van de hand te doen beschermt u het milieu en de volksgezondheid tegen mogelijke
negatieve gevolgen, die anders zouden kunnen voortvloeien uit het onjuist verwerken van de resten van dit product.
Voor gedetailleerde informatie over het terugnemen en recycleren van dit product, gelieve contact op te nemen met de
leverancier van dit product.
Italian
Informazioni sul riciclo del prodotto:
Le seguenti informazioni riguardano gli stati membri EU:
Il simbolo con il bidone sbarrato indica il non poter smaltire questo prodotto come rifiuto domestico.
L'accertamento che questo prodotto sia smaltito correttamente contribuirà ad impedire le potenziali conseguenze
negative per l'ambiente e la salute umana che potrebbero essere causati, al contrario, dall'errato smaltimento dello
stesso. Per informazioni più dettagliate sulle modalita di resa e riciclaggio di questo prodotto mettetevi in contatto con il
fornitore da cui l'avete aquistato.
Portuguese
Informação sobre reciclagem:
A informação que se segue é apenas dirigida a países membros da CEE:
A utilização deste símbolo indica que este produto não pode ser tratado como lixo comum.
Ao assegurar-se que este produto é tratado correctamente está a ajudar a prevenir potenciais consequências negativas
para o ambiente e para a saúde humana, que poderiam ser causadas pelo inapropriado tratamento deste produto.
Para mais informação sobre a reciclagem e tratamento deste produto, contacte o seu fornecedor.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
PRINTED IN TAIWAN
EO1-12031
E
Download from Www.Somanuals.com. All Manuals Search And Download.
|