OWNER’S MANUAL
Color Television
®
I
Owner's Record
The model number and serial number are on the back
of your TV. Record these numbers in the spaces below.
Refer to these numbers whenever you communicate
with your Toshiba dealer about this TV.
Model number:
Serial number:
34AS42
© 2002 TOSHIBA CORPORATION
All Rights Reserved.
23565685
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safety Instructions
Installation, Care, and Service
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
Installation
Follow these recommendations and precautions and heed all
warnings when installing your TV:
4) Follow all instructions.
15) Never modify this equipment. Changes or modifications
may void: a) the warranty, and b) the user’s authority to
operate this equipment under the rules of the Federal
Communications Commission.
5) Do not use this apparatus near
water.
16)
DANGER: RISK OF SERIOUS PERSONAL
INJURY, DEATH, OR EQUIPMENT
DAMAGE! Never place the TV on
6) Clean only with a dry cloth.
an unstable cart, stand, or table. The TV
may fall, causing serious personal injury,
death, or serious damage to the TV.
7) Do not block any ventilation
openings. Install in accordance with
the manufacturer’s instructions.
17) Never place or store the TV in direct
sunlight; hot, humid areas; areas
subject to excessive dust or vibration;
or locations with temperatures at or
below 41°F (5°C).
8) Do not install near any heat
sources such as radiators,
heat registers, stoves, or other
apparatus (including amplifiers)
that produce heat.
9) Do not defeat the safety purpose of the polarized or
grounding type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug has
two blades and a third grounding
18) Always place the TV on the floor
or a sturdy, level, stable surface that
can support the weight of the unit.
Wide plug
prong. The wide blade or the third
prong are provided for your safety.
If the provided plug does not fit into
your outlet, consult an electrician
for replacement of the obsolete outlet.
CAUTION: To reduce the risk of electric shock, do not
use the polarized plug with an extension cord, receptacle,
or other outlet unless the blades can be inserted
completely to prevent blade exposure.
19) Never place items such as vases,
aquariums, or candles on top of the TV.
10) Protect the power cord from being
walked on or pinched, particularly at
plugs, convenience receptacles, and
the point where it exits the apparatus.
20) Never block or cover the slots or
openings in the TV cabinet back,
bottom, and sides. Never place
the TV:
• on a bed, sofa, rug, or similar
surface;
11) Only use attachments/accessories specified by the
manufacturer.
• too close to drapes, curtains,
12) Use only with the cart, stand, tripod,
bracket, or table specified by the
manufacturer, or sold with the
or walls; or
• in a confined space such as a
bookcase, built-in cabinet, or any
other place with poor ventilation.
The slots and openings are provided
to protect the TV from overheating
and to help maintain reliable
operation of the TV.
apparatus. When a cart is used, use
caution when moving the cart/apparatus
combination to avoid injury from tip-over.
13) Unplug this apparatus during
lightning storms or when
unused for long periods
of time.
21) Never allow anything to rest on or roll over the power
cord, and never place the TV where the power cord is
subject to wear or abuse.
14) Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power supply
cord or plug is damaged, liquid has
22) Never overload wall outlets and
extension cords.
been spilled or objects have fallen into
the apparatus, the apparatus has been
exposed to rain or moisture, does not
operate normally, or has been dropped.
QUALIFIED
SERVICE
TECHNICIAN
05/02.2
3
Download from Www.Somanuals.com. All Manuals Search And Download.
29) [This item applies to projection TVs only.] If the air
temperature rises suddenly (for example, when the TV is
first delivered), condensation may form on the lenses. This
can make the picture appear distorted or the color appear
faded. If this happens, turn off the TV for 6 to 7 hours to
allow the condensation to evaporate.
23) Always operate this equipment from
a 120 VAC, 60 Hz power source only.
30) For added protection of your TV from lightning and power
surges, always unplug the power cord and disconnect the
antenna from the TV if you leave the TV unattended or
unused for long periods of time.
24) Always make sure the antenna system is properly
grounded to provide adequate protection against voltage
surges and built-up static charges (see Section 810 of the
National Electric Code).
Antenna lead-in wire
31) During normal use, the TV may make
occasional snapping or popping
Antenna discharge unit
(NEC Section 810-20)
Ground clamp
sounds. This is normal, especially
when the unit is being turned on or
off. If these sounds become frequent
or continuous, unplug the power cord
and contact a Toshiba Authorized Service Center.
Grounding conductors
(NEC Section 810-21)
Electric service equipment
Power service grounding
32) Possible Adverse Effects on TV Picture Tube: If a fixed
(non-moving) pattern remains on the TV screen for long
periods of time, the image can become permanently
engrained in the picture tube and cause subtle but
permanent ghost images. This type of damage is NOT
COVERED BY YOUR WARRANTY. Never leave your TV
on for long periods of time while it is displaying the
following formats or images:
electrode system (NEC Art 250 Part H)
Ground clamps
25)
DANGER: RISK OF SERIOUS PERSONAL
INJURY OR DEATH!
• Use extreme care to make sure you are never in
a position where your body (or any item you are in contact
with, such as a ladder or screwdriver) can accidentally
touch overhead power lines. Never locate the antenna
near overhead power lines or other electrical circuits.
• Never attempt to install any of the following during
lightning activity:
a) an antenna system; or b) cables, wires, or any home
theater component connected to an antenna or phone
system.
• Fixed Images, such as PIP/POP windows, stock tickers,
video game patterns, TV station logos, and websites.
• Special Formats that do not use the entire screen. For
example, viewing letterbox style (16:9) media on a
normal (4:3) display (gray bars at top and bottom of
screen); or viewing normal style (4:3) media on a
widescreen (16:9) display (gray bars on left and right
sides of screen).
Care
Service
33)
For better performance and safer operation of your TOSHIBA
TV, follow these recommendations and precautions:
WARNING: RISK OF ELECTRIC
SHOCK! Never attempt to service the
TV yourself. Opening and
26) Always sit approximately 10–25 feet away from the TV and
as directly in front of it as possible. The picture can appear
dull if you sit too far to the left or right of the TV, or if
sunlight or room lights reflect on the screen. Turn the TV
off to check for reflections on the screen, and then remove
the source of reflections while viewing the TV.
removing the covers may expose
you to dangerous voltage or other
hazards. Refer all servicing to a
Toshiba Authorized Service Center.
QUALIFIED
SERVICE
TECHNICIAN
34) If you have the TV serviced:
• Ask the service technician to use only replacement parts
specified by the manufacturer.
• Upon completion of service, ask
the service technician to perform
routine safety checks to determine
that the TV is in safe operating
condition.
27) Always unplug the TV before
cleaning. Never use liquid or
aerosol cleaners.
35) When the TV reaches the end of its useful life, ask a
qualified service technician to properly dispose of the TV.
Improper disposal may result in a picture tube implosion
and possible personal injury.
28)
WARNING: RISK OF ELECTRIC SHOCK!
Never spill liquids or push objects of any kind
into the TV cabinet slots.
05/02.2
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Important safety information............................. 2–4
Using the TV’s features........................................... 18
Adjusting the channel settings....................................... 18
Switching between two channels .............................. 18
Programming your favorite channels ........................ 18
Using the V-Chip Control (blocking) feature ................ 19
Selecting a PIN code ................................................ 19
Changing your PIN code ......................................... 20
If you forget your PIN code ................................. 20
Blocking programs by ratings ................................... 21
Ratings definitions (MPAA, Youth TV, TV) ............. 21
Unblocking programs temporarily ........................... 22
Blocking unrated movies and programs.................... 23
Blocking channels .................................................... 24
Adjusting the picture .................................................... 25
Adjusting the picture quality .................................... 25
Selecting the color temperature ................................ 25
Adjusting the picture preference............................... 26
Displaying on-screen information ................................. 26
Setting the off timer ...................................................... 26
Auto power off .............................................................. 26
Using the closed caption feature.................................... 27
Adjusting the sound ...................................................... 28
Muting the sound .................................................... 28
Selecting stereo/SAP broadcasts ............................... 28
Adjusting the sound quality ..................................... 29
Using the surround sound feature ............................ 29
Viewing the demonstration (DEMO) mode ................. 30
Understanding the last mode memory feature ............... 30
Introduction............................................................... 6
Exploring your new TV ................................................ 6
Selecting a location for your TV.................................... 6
Connecting your TV ................................................. 7
Note regarding picture quality .................................. 7
Connecting a VCR ....................................................... 7
Connecting a cable converter box ................................. 7
Connecting a cable converter box and a VCR ............... 8
Connecting a satellite receiver and a VCR ..................... 8
Connecting a DVD player with ColorStream®
(component video) and a VCR ..................................... 9
Connecting two VCRs .................................................... 9
Using the remote control ....................................... 10
Preparing the remote control for use ............................. 10
Installing the remote control batteries ........................... 10
Location of controls on TV and remote control ............ 11
Using the remote control to operate a VCR or
cable TV converter ........................................................ 12
Programming the remote control to operate a
non-Toshiba VCR or cable TV converter ...................... 13
VCR codes............................................................... 14
Cable TV converter codes ........................................ 14
Setting up your TV ...................................................15
Menu system (general instructions) ............................... 15
Changing the on-screen display language ...................... 16
Selecting the signal source ............................................. 16
Programming channels into the TV’s memory .............. 16
Programming channels automatically ....................... 16
Adding and erasing channels manually..................... 17
Changing channels........................................................ 17
Appendix....................................................................31
Specifications ................................................................ 31
Troubleshooting ............................................................ 32
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
• This owner’s manual applies to model 34AS42.
• Instructions in this manual are based on using the remote control; however, you can use the buttons on the front panel
of the TV if they have the same name as those referred to on the remote control.
• Check the model and serial numbers on the back of your TV before using this manual. Write the numbers in the space
provided on the front cover of this manual for your records.
Exploring your new TV
• You can operate your TV using the buttons on the front panel or remote control.
• The front (VIDEO-3) and back panels provide inputs for connecting other equipment to your TV.
Front of TV
34AS42
POWER
RECALL
MUTE
o
3
6
1
4
2
5
8
0
9
7
CH RTN
VIDEO-3
100
ENT
CH
MENU/
ENTER
VOL
VOL
Back of TV
IN
OUT
ANT
COLOR
STREAM
INPUT
CH
VIDEO
VIDEO
VIDEO
TV
CABLE
VCR
Y
L
L/
MONO
L/
EXIT
MONO
FAV CH
TV/VIDEO
A
S-VIDEO
P
AUDIO
R
AUDIO
R
AUDIO
R
B
REC TV/VCR STOP
PLAY
FF
STILL SOURCE PIP
P
IN
OUT
VIDEO
SLOW PAUSE REW
R
COLOR
ANT
VIDEO
V
I
D
E
O
S
T
R
E
A
M
INPUT
Y
L
L/
MONO
L/
VIDEO-1 VIDEO-2
MONO
S-VIDEO
AUDIO
R
AUDIO
R
C
B
R
AUDIO
R
C
V
I
D
E
O
-
1
V
I
D
E
O
-
2
PIP CH
LOCATE SWAP
VIDEO-1
VIDEO-2
CT-90037
Selecting a location for your TV
• Place the TV either on the floor or on the TV stand listed
in the “Specifications” section.
• Place the TV in a location where light does not directly
hit the screen.
• Place the TV far enough from the walls to allow proper
ventilation. Inadequate ventilation may cause
overheating, which can damage the TV.
NOTE: Before installing your TV, please read the important
safety information on pages 2–4.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting your TV
Note: Cables are not supplied with your TV.
ꢀ
Coaxial cable is the cable that comes in from your antenna, cable TV service, or cable
converter box. Coaxial cable uses “F” connectors.
Coaxial (antenna) cable
ꢀ
Standard stereo A/V cables usually come in sets of three, and are typically color-coded
according to use: yellow for video, red for stereo right audio, and white for stereo left (or
mono) audio. Your TV’s standard A/V inputs are color-coded in the same manner as
the cables.
Standard stereo A/V cables
(typically color-coded yellow for video,
red and white for audio)
ꢀ
ꢀ
S-Video cable is for use with video equipment that has S-Video connectors.
Component video cables come in sets of three (typically color-coded red, green, and
blue), and are for use with video equipment that has component video connectors. Your TV’s
ColorStream® (component video) inputs are color-coded in the same manner as the cables.
S-video cable
NOTE REGARDING PICTURE QUALITY
When connecting video equipment to your Toshiba TV:
ꢀ
ꢀ
For GOOD picture quality: Use a standard yellow video cable.
Component video cables
(typically color-coded red, green, blue)
For BETTER picture quality: If your equipment has S-video connectors, use an S-video
cable instead of a standard yellow video cable. (You still must connect the standard
red and white audio cables for full system connection, but do not connect a standard
yellow video cable at the same time or the picture performance will be unacceptable.)
For BEST picture quality: If your equipment has component video connectors, use
component video cables instead of a standard yellow video cable or S-video cable. (You
still must connect the standard red and white audio cables for full system connection.)
CAUTION: Do not plug in any power cords
until you have finished connecting all equipment.
ꢀ
Connecting a VCR
Connecting a cable converter box
With this connection you can:
With this connection you can:
• watch TV channels and videotapes
• watch basic and premium cable channels
• record one channel while watching the same or
another channel
Tune the TV to channel 3 or 4 (whichever channel is
vacant in your area), and then use the converter box to
change channels.
You will need:
• one coaxial cable
Note:
When you use a converter box with your TV, you may not be
able to use the remote control to program certain features (for
example, blocking channels).
• one pair of audio cables (one single audio cable for a
mono VCR)
• one video cable (For video cable type, see “Note
Regarding Picture Quality,” above.)
From cable
TV
Note:
IN
OUT
IN
OUT
ANT
COLOR
STREAM
INPUT
If you have a mono VCR, connect L/Mono to VCR Audio OUT
using only one audio cable.
VIDEO
VIDEO
VIDEO
Y
L
L/
MONO
L/
MONO
Cable converter
box
The VIDEO-2 inputs on the back of the TV (and the VIDEO-3
inputs on the front of the TV) can be used for connecting a second
(and third) piece of video equipment, such as a DVD player or
camcorder (see “Note Regarding Picture Quality” above).
S-VIDEO
P
AUDIO
R
AUDIO
R
AUDIO
R
B
P
R
VIDEO-1 VIDEO-2
From cable or antenna
Stereo VCR
The unauthorized recording, use, distribution, or revision of
television programs, videotapes, DVDs, and other materials
is prohibited under the Copyright Laws of the United States
and other countries, and may subject you to civil and
criminal liability.
S-VIDEO
VIDEO
OUT
L
R
IN
IN from ANT OUT to TV
CH3
OUT
CH4
TV
IN
OUT
ANT
COLOR
STREAM
INPUT
VIDEO
VIDEO
VIDEO
Y
L
L/
MONO
L/
MONO
S-
AUDIO
P
AUDIO
R
AUDIO
R
B
R
R
P
VIDEO-1 VIDEO-2
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting a cable converter box and a VCR
With this connection you can:
• watch videotapes
• watch and record basic and premium cable channels
• record one channel while watching the same or another channel
From
Cable
OUT
IN
Cable
Tune the VCR to channel
3 or 4 (whichever channel is vacant
Stereo VCR
Converter
Box
S-VIDEO
VIDEO
AUDIO
L
R
in your area), place the TV in
VIDEO 1 mode, and then use the
converter box to change channels.
IN
IN from ANT OUT to TV
OUT Cable
Signal
OUT Splitter
IN
CH3
CH4
OUT
You will need:
• one cable signal splitter
• two coaxial cables
TV
IN
OUT
COLOR
STREAM
VIDEO
VIDEO
VIDEO
INPUT
Y
L
L/
L/
• one pair of audio cables (one single
audio cable for a mono VCR)
MONO
MONO
S-V
ANT
P
P
AUDIO
R
AUDIO
R
AUDIO
R
B
R
• one video cable (For video cable type,
see “Note Regarding Picture Quality” on page 7.)
VIDEO-1 VIDEO-2
Note:
If you have a mono VCR, connect TV L/Mono Audio IN
to VCR Audio OUT using only one audio cable.
When you use a converter box with your TV, you
may not be able to use the remote control to program
certain features (for example, blocking channels).
The unauthorized recording, use, distribution, or revision of
television programs, videotapes, DVDs, and other materials
is prohibited under the Copyright Laws of the United States
and other countries, and may subject you to civil and
criminal liability.
Connecting a satellite receiver and a VCR
With this connection you can:
• watch videotapes
From Satellite dish
• watch satellite and TV channels
Satellite Receiver
• record one TV channel while watching
the same or another channel
VIDEO
AUDIO
S-VIDEO
OUT
Satellite IN
L
R
You will need:
OUT
• one coaxial cable
• two pairs of audio cables (one single and one
pair of audio cables for a mono VCR)
TV
IN
OUT
ANT
COLOR
STREAM
INPUT
VIDEO
VIDEO
VIDEO
• two video cables (For video cable type, see
“Note Regarding Picture Quality” on page 7.)
Y
L/
MONO
L/
MONO
S-
Note:
P
AUDIO
R
AO
R
AUDIO
R
B
R
To watch satellite programs, the TV must select
VIDEO-1 (see page 16).
P
VIDEO-1 VIDEO-2
To watch VCR programs, the TV must select
VIDEO-2 (see page 16).
Stereo VCR
S-VIDEO
VIO
UDI
OUT
IN from ANT OUT to TV
CH3
IN
CH4
From antenna
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting a DVD player with ColorStream® (component video) and a VCR
Your TV has ColorStream® (component video) inputs. Connecting your TV to a component video-compatible DVD player
(such as a Toshiba DVD player with ColorStream®) can greatly enhance picture quality and performance.
With this connection you can:
• watch TV channels, DVDs, and videotapes
From antenna
Stereo VCR
• record TV channels
S-VIDEO
VIDEO
AUDIO
L
R
• record one channel while watching the same or
another channel
IN
IN from ANT OUT to TV
CH3
OUT
CH4
You will need:
• one coaxial cable
TV
IN
OUT
ANT
COLOR
STREAM
INPUT
VIDEO
VIDEO
VIDEO
• two pairs of audio cables (one single and one pair of
audio cables for a mono VCR)
Y
L
L/
L/
MONO
MONO
-
AUDIO
• two video cables (If your DVD player has component
video, use one standard video or S-video cable from the
VCR and one set of component video cables from the
DVD player. See “Note Regarding Picture Quality” on
page 7.)
P
AUDIO
R
AUDIO
R
B
R
P
R
VIDEO-1 VIDEO-2
Note:
To watch the VCR, the TV must select VIDEO 1 (see page 16).
PR
PB
Y
1
2
L
L
R
R
To watch the DVD player, the TV must select VIDEO 2
(see page 16).
VIDEO
VIDEO OUT
S-VIDEO
COMPONENT VIDEO OUT
AUDIO OUT
DVD player with component video
Connecting two VCRs
The unauthorized recording, use, distribution, or revision of
television programs, videotapes, DVDs, and other materials
is prohibited under the Copyright Laws of the United States
and other countries, and may subject you to civil and
criminal liability.
With this connection you can:
• watch TV channels and videotapes
• record TV channels
• record one TV channel while watching the same or
another channel
• record (dub/edit) from one VCR to the other VCR
while watching a videotape
From antenna
VCR1
S-VIDEO
VIDEO
AUDIO
You will need:
L
R
IN
IN from ANT OUT to TV
CH3
• one coaxial cable
• two pairs of audio cables (two single audio cables
for mono VCRs)
OUT
CH4
• two video cables (For video cable type, see “Note
Regarding Picture Quality” on page 7.)
TV
IN
OUT
ANT
COLOR
STREAM
INPUT
VIDEO
VIDEO
VIDEO
Y
L
Note:
L/
MONO
L/
MONO
S-V
AUDIO
Do not connect the same VCR to both the OUT and the IN
connections on the TV at the same time.
P
AUDIO
R
AUDIO
R
B
R
P
R
To record (dub/edit) from VCR 1 to VCR 2, the TV must
select VIDEO 1 (see page 16), and VCR 2 must select
LINE IN.
VIDEO-1 VIDEO-2
VCR2
VO
UDI
IN
IN from ANT OUT to TV
CH3
OUT
CH4
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the remote control
Preparing the remote control for use
Your TV remote control can operate your TVand most VCRs and cable TV converters, even if they are different brands.
If you have a Toshiba VCR or cable TV converter:
Your TV remote control is already programmed to operate it. See page 12.
If you have a non-Toshiba VCR or cable TV converter:
You must first program your remote control so it will operate the other equipment. See pages 12–14.
Installing the remote control batteries
1 Slide the battery cover off the back of the remote control.
Caution:
Dispose of batteries in a designated disposal
area. Do not throw batteries into a fire.
Press and slide to remove.
Do not mix battery types or combine used
batteries with new ones.
Remove dead batteries immediately to prevent
battery acid from leaking into the battery
compartment.
If you do not intend to use the remote control
for a long time, remove the batteries.
2 Install two “AA” size batteries, making sure to match the + and –
signs on the batteries to the signs on the battery compartment.
Note:
If your Toshiba TV remote control does not
operate all of the features of your VCR or cable
TV converter, use the original remote control
for your other equipment.
3 Slide the battery cover back onto the remote control until the lock
snaps.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Location of controls on TV and remote control
For details on the use of each control, refer to pages in brackets.
TV front panel
TV/VIDEO [16]
VOLUME T/S[28]
CHANNEL s/t[16]
MENU
TV / VIDEO
VOLUME
CHANNEL
POWER
POWER [12]
T/S/t/s[15]
Remote control
sensor
MENU [15]
POWER indicator
Remote control
●
The shaded buttons in the picture below glow in the dark.
MUTE [28]
POWER
RECALL
MUTE
RECALL [26]
o
POWER [12]
3
6
1
4
2
5
8
0
Channel Numbers [16]
9
7
CH RTN
100
CH RTN [18]
MENU [15]
ENT
CH
MENU/
ENTER
CHANNEL s/t[16]
or Menu s/t[15]
VOL
VOL
VOLUME T/S[28]
or Menu T/S[15]
CH
TV
CABLE
VCR
TV/CABLE/VCR switch [12]
(Set to “TV” to control the TV).
EXIT [15]
EXIT
FAV CH
TV/VIDEO
A
TV/VIDEO [16]
FAV CH t/s[18]
REC TV/VCR STOP
PLAY
FF
STILL SOURCE PIP
SLOW PAUSE REW
VCR function buttons
PIP CH
LOCATE SWAP
Note: The PIP functions (Still,
Source, PIP, PIP Ch, Locate, and
Swap) are not available.
CT-90037
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the remote control to operate a VCR or cable TV converter
• If you have a non-Toshiba VCR or cable TV converter, you must first program the remote control to recognize your
VCR or converter brand (see pages 13–14).
• To use your TV remote control to operate a VCR, set the TV/CABLE/VCR switch to VCR. The shaded buttons in the
picture below will then operate the VCR instead of the TV.
• To use your TV remote control to operate a cable TV converter, set the TV/CABLE/VCR switch to CABLE. The
shaded buttons shown in the picture below will then operate the converter instead of the TV.
Point the remote control at the VCR or cable TV converter
POWER
RECALL
MUTE
o
POWER
Turns the VCR (or cable TV
converter) on and off.
3
6
1
4
2
5
8
0
Channel Numbers
Press to directly access channels (as
opposed to the Channel s/tbuttons).
9
7
CH RTN
100
ENT
ENTER
Required by some VCRs and cable TV
converters to change the channel.
CH
MENU/
ENTER
VOL
VOL
CHANNEL s/t
sselects the next higher channel,
and tselects the next lower channel.
TV/CABLE/VCR Switch
Set to CABLE to control the
cable converter; set to VCR to
control the VCR.
CH
TV
CABLE
VCR
STOP
EXIT
Stops the tape.
TV/VCR
FAV CH
TV/VIDEO
A
To view one program while
recording another, press to select
TV mode.
PLAY
Begins tape playback.
REC TV/VCR STOP
PLAY
FF
STILL SOURCE PIP
SLOW PAUSE REW
REC
FF
PIP CH
LOCATE SWAP
Starts tape recording.
Fast-forwards the tape.
In play mode, press to view the picture
moving rapidly forward.
SLOW
In play mode, press to view a
slow-motion picture.
CT-90037
REW
PAUSE
Rewinds the tape.
In play mode, press to view the
picture moving rapidly backward.
In play or record mode, press to freeze
the picture; press again to release.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming the remote control to operate a non-Toshiba VCR
or cable TV converter
Your Toshiba TV remote control is preprogrammed to operate Toshiba brand VCRs and cable TV converters. To
program your TV remote control to operate a non-Toshiba VCR or a cable TV converter, follow these steps:
1 In the code table on page 14, find the code for your brand of VCR or
cable TV converter.
If more than one code is listed, try each one separately until you find
one that works.
RECALL
POWER
RECALL
MUTE
o
POWER
2 Set the TV/CABLE/VCR switch to VCR (for a VCR), or CABLE (for
3
6
1
4
2
5
8
0
a cable TV converter).
Channel
Numbers
3 While holding down RECALL, press the Channel Number buttons
to enter the 3-digit code for your brand of VCR or converter.
9
7
CH RTN
4 To test the code, turn the VCR or converter on, point the remote
100
ENT
control at it, and press POWER.
–If the correct code was entered, the VCR or converter will turn off.
CH
–If the VCR or converter does not respond, repeat steps 1–4 using
another code.
MENU/
ENTER
VOL
VOL
–If the VCR or converter does not respond to a different code,
you will need to use the remote control that came with your VCR or
converter.
CH
TV
CABLE
VCR
EXIT
FAV CH
TV/VIDEO
A
5 Set the TV/CABLE/VCR switch to TV to control the TV.
For future reference, write down the code(s) you used:
VCR Code:
REC TV/VCR STOP
PLAY
FF
STILL SOURCE PIP
SLOW PAUSE REW
PIP CH
LOCATE SWAP
Cable TV Converter Code:
CT-90037
Note:
You must reprogram the remote control every time the batteries are changed.
Some newer VCRs respond to either of two codes. These VCRs have a switch
labeled “VCR1/VCR2.” If your VCR has this kind of switch and does not respond
to the codes for your VCR brand, set the switch to the other position (“VCR1” or
“VCR2”) and reprogram the remote control.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming the remote control to operate a non-Toshiba VCR or
cable TV converter (cont.)
In some rare cases, you may not be able to operate your non-Toshiba equipment with your TV remote control. Your
other equipment may use a code that is not recognized by the TV remote control. If this happens, you will need to use
the remote control that came with your other equipment.
VCR codes
Cable TV converter codes
MTC............................. 019, 259
Multitech ..................... 019, 091
NAD ............................. 077
NEC ............................. 057, 059, 060, 069, 086
Nikko ........................... 056
Noblex ......................... 259
Olympus ...................... 054
Optimus ...................... 056, 067, 077, 123
Optonica ...................... 081
Orion ........................... 498
Panasonic ................... 054, 096, 181, 244, 473
Penney ........................ 054, 056, 057, 059, 061,
073, 259
Pentax ......................... 061, 084, 124
Philco .......................... 054
Philips ......................... 054, 081, 100, 129
Pilot ............................. 056
ABC .................................. 020,022,026,027,030,
032, 033, 036, 066
Adventura .................... 019
Aiko ............................. 297
Antronix ........................... 041
Archer .............................. 041, 058, 172
Belcor ............................... 075
Cable Star ........................ 075
Cabletenna ....................... 041
Cableview ......................... 041
Century ............................ 172
Citizen .............................. 172
Colour Voice .................... 044, 050
Comtronics ...................... 059, 079
Contec .............................. 038
Dae Ryung ....................... 027
Eastern ............................. 021
Focus ............................... 419
Garrard ............................. 172
GC Electronics ................. 075
Gemini .............................. 034, 089
General Instrument .......... 030, 295
Goldstar ........................... 059, 163
Hamlin .............................. 028, 039, 053, 278,
292
Aiwa ............................ 019
Akai ............................. 060, 068, 080, 125, 261
American High ............ 054
Asha ............................ 259
Audiovox ..................... 056
Beaumark .................... 259
Bell & Howell .............. 123
Brandt ......................... 206
Broksonic .................... 140, 203, 230, 314, 380
Calix ............................ 056
Canon .......................... 054
Capehart ...................... 039
Carver.......................... 100
CCE ............................. 091, 297
Citizen ......................... 056, 297
Colt .............................. 091
Pioneer ........................ 077, 086
Portland ...................... 039
Craig ............................ 056, 066, 091, 259
Curtis Mathes .............. 054, 060, 079
Cybernex ..................... 259
Protec.......................... 091
Pulsar .......................... 058
Quarter ........................ 065
Daewoo ....................... 039, 064, 297
Daytron ....................... 039
Quarts ......................... 065
Hitachi .............................. 030
Hytex ................................ 026
Jasco ................................ 172
Jerrold .............................. 022, 030, 031, 033,
034, 066, 295
Macom ............................. 052
Magnavox ........................ 046
Memorex .......................... 019
Movie Time ...................... 175
NSC .................................. 089, 175
Oak ................................... 026, 038, 267
Panasonic ........................ 019, 040, 126
Paragon ............................ 019
Philips .............................. 044, 046, 047, 048,
049, 050, 172
Pioneer ............................. 042, 163, 552
Popular Mechanics .......... 419
Pulsar ............................... 019
RCA .................................. 040
Recoton ............................ 419
Regal ................................ 039, 278, 292
Regency ........................... 021
Rembrandt ....................... 030, 089
Runco ............................... 019
Samsung .......................... 059, 163
Scientific Atlanta .............. 025, 027, 036, 296
Signal ............................... 034, 059
Signature ......................... 030
SL Marx ........................... 059
Sprucer ............................ 040
Standard Components ..... 174
Starcom ........................... 022, 034, 066
Stargate............................ 034, 059
Starquest ......................... 034
Sylvania............................ 020
Teleview ........................... 059
Texscan ............................ 020
Tocom .............................. 031, 032, 078
Toshiba ............................ 019
Tusa ................................. 034
Unika ................................ 041, 172
United Artists ................... 026
United Cable ..................... 022
Universal .......................... 041, 058, 075, 172
Viewstar ........................... 046, 079, 230
Zenith ............................... 019
Zentek .............................. 419
Quasar ......................... 054, 096
Radio Shack ................ 019, 056, 344
Radix ........................... 056
Dynatech ..................... 019
Electrohome ................ 056
Electrophonic .............. 056
Randex ........................ 056
RCA ............................. 061, 079, 084, 096, 124,
125, 168, 221
Realistic ...................... 019, 054, 056, 065, 066,
067, 081, 085, 123, 259
Ricoh ........................... 053
Runco .......................... 058
Samsung ..................... 064, 259
Sanky .......................... 058, 067
Sansui ......................... 060, 086
Sanyo .......................... 065, 066, 123, 259
Scott ............................ 062, 064, 140, 203, 229,
230, 231
Sears ........................... 054, 056, 061, 065, 066,
073, 085, 123, 124
Sharp .......................... 067, 081
Shintom ...................... 091
Shogun........................ 259
Singer.......................... 091
Sony ............................ 051, 052, 053, 054
STS ............................. 061
Sylvania....................... 019, 054, 062, 100, 129
Symphonic .................. 019, 344
Tatung ......................... 060
Teac ............................ 019, 060
Technics ...................... 054, 181
Teknika ........................ 019, 054, 056, 071
Telefunken .................. 206
TMK............................. 227, 259
Toshiba ....................... 062, 064, 085, 229, 231,
385
Totevision ................... 056, 259
Unitech ........................ 259
Vector.......................... 064
Vector Research ......... 057, 059
Video Concepts ........... 059, 064, 080
Videosonic .................. 259
Wards .......................... 019, 054, 061, 066, 067,
081, 091, 168, 231, 259
XR-1000 ...................... 019, 054, 091
Yamaha ....................... 057
Zenith .......................... 052, 053, 058
Emerex ........................ 051
Emerson ...................... 019, 021, 056, 062, 080,
087, 140, 203, 227, 228,
230, 231, 297, 313, 314,
380, 498
Fisher .......................... 066, 073, 085, 123
Fuji .............................. 052, 054
Funai ........................... 019, 344
Garrard ........................ 019, 344
GE ............................... 054, 079, 084, 221
Goldstar ...................... 037, 056, 057
Gradiente..................... 019
Harley Davidson .......... 019
Harman/Kardon........... 057, 094
Harwood ..................... 087, 091
Headquarter ................ 065
HI-Q ............................ 066
Hitachi ......................... 060, 061, 084, 124, 185,
254
Jensen ......................... 060
JVC .............................. 027, 060, 086
Kenwood ..................... 057, 060, 086
KLH ............................. 091
Kodak .......................... 054, 056
Lloyd ........................... 019
Lloyd’s ........................ 227
Logik ........................... 091
LXI............................... 056
Magnavox ................... 054, 058, 100, 129, 168
Magnin ........................ 259
Marantz ....................... 054, 100
Marta ........................... 056
Matsushita .................. 054
MEI .............................. 054
Memorex ..................... 019, 054, 056, 058, 065,
066, 067, 123, 259
MGA ............................ 062, 080
MGN Technology ........ 259
Minolta ........................ 061, 124
Mitsubishi ................... 062, 080, 086, 094, 192,
233, 261
Motorola ..................... 054, 067
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up your TV
TV Front Panel
Menu system (general instructions)
MENU
TV/VIDEO
VOLUME
CHANNEL
POWER
After installing the batteries and programming the remote control, you
will need to set some preferences on your TV using the menu system.
You can access the menus using the buttons on the TV front panel or
remote control. Following are general instructions for using the menu
system:
MENU
T/ S
t/ s
1. Repeatedly press MENU to select a menu (Picture, Audio, Setup,
Preference, or Closed Caption, as shown in the menu system
overview, below).
2. Press tor sto select the function you want to adjust in the menu
(the t/sbuttons function as CHANNEL t/sbuttons when no
menu is on-screen).
POWER
RECALL
MUTE
o
3
6
1
4
2
5
8
0
3. Press Tor Sto adjust the selected function (the T/Sbuttons
function as VOLUME T/Sbuttons when no menu is on-screen).
4. When you make a menu selection, your changes occur immediately.
You do not have to press MENU or EXIT to save your changes.
Note: The TV front panel does not have an EXIT button.
9
7
CH RTN
100
ENT
5. On-screen menus close automatically if no adjustments are made
within 15 seconds. To close an on-screen menu instantly, press EXIT
on the remote control.
CH
MENU/
ENTER
T/ S
VOL
VOL
s/ t
CH
MENU
TV
CABLE
VCR
EXIT
EXIT
Menu system overview
FAV CH
TV/VIDEO
A
Picture
REC TV/VCR STOP
PLAY
FF
STILL SOURCE PIP
SLOW PAUSE REW
PIP CH
LOCATE SWAP
PICTURE
CONTRAST
BRIGHTNESS 50
SHARPNESS 50
50
Audio
COLOR
TINT
50
0
CT-90037
RESET
AUDIO
MTS:
[STR] SAP MONO
[
]
MOVE
AD
BASS
TREBLE
BALANCE
Set Up 1
50
50
0
SURROUND: [ON] O
SET UP
Set Up 2
[
]
L
ANGU
AGE:
MOVE
ADJU
[ENGLISH] FRANCAIS ESPANOL
TV/CABLE:
[TV
CH PROGRAM
ADD/ERASE:
V-CHIP CONTROL
MORE
[A
SET UP
MORE
Preference
[
]
MOVE
SELECT
TIMER:
0 MIN
START [STOP]
DEMO:
FAVORITE CH
PREFERENCE
Closed
Caption
COLOR TEMPERATURE
[
]
MOVE
SEL
[COOL] MEDIUM WARM
PICTURE PREFERENCE
[SPORTS] STAND
CLOSED CAPTI0N
CC:
SELEC
C1 C2 C3 C4 T1
T2 T3 T4 [OFF]
[
]
MOVE
[
]
[
]
MOVE
SELECT
15
Download from Www.Somanuals.com. All Manuals Search And Download.
TV Front Panel
Changing the on-screen display language
Choose from three different languages (English, French, or Spanish) for
the on-screen display of menus and messages.
CHANNEL s/t
TV/VIDEO
MENU
TV/VIDEO
VOLUME
CHANNEL
POWER
To select an on-screen display language:
1. Press MENU.
2. Press x or • until the SET UP menu appears.
3. Press y or z to highlight LANGUAGE.
4. Press x or • to highlight your desired language.
MENU
T/ S t/s
RECALL
POWER
MUTE
RECALL
SET UP
CONFIGURATION
o
LANGUAGE:
LANGUE:
[ENGLISH] FRANCAIS ESPANOL
ENGLISH [FRANCAIS] ESPANOL
TV/CABLE:
[TV] CABLE
TV/CABLE:
[TV] CABLE
CH PROGRAM
ADD/ERASE:
V-CHIP CONTROL
MORE
PROGRAMME CAN
AJOUT/EFF:
CONTROLE V-CHIP
PLUS
3
2
1
4
[ADD] ERASE
[AJOUT] EFF
[
]
[
]
5
8
0
6
MOVE
SELECT
[
]
[
]
BOUGER
CHOISIR
CHANNEL
NUMBERS
9
7
CH RTN
Selecting the signal source
100
ENT
Use the TV/VIDEO button on the remote control or TV to select the signal
source connected to your TV.
MENU
CH
To change the signal source:
MENU/
ENTER
VOL
VOL
yz x •
Repeatedly press TV/VIDEO to select either TV, VIDEO 1,
VIDEO 2, or VIDEO 3. The selected signal source is highlighted
on-screen.
CH
TV
CHANNEL yz
CABLE
VCR
EXIT
TV
FAV CH
TV/VIDEO
A
VIDEO 1
VIDEO 2
VIDEO 3
TV/VIDEO
REC TV/VCR STOP
PLAY
FF
STILL SOURCE PIP
SLOW PAUSE REW
TO SELECT PUSH TV/VIDEO
PIP CH
LOCATE SWAP
To verify the signal source:
Press RECALL.
CT-90037
Programming channels into the TV’s memory
When you press CHANNEL ▲▼ on the TV or remote control,
the TV stops only on the channels stored in the TV’s memory.
Note: To tune the TV to a channel not programmed into the memory,
use the CHANNEL NUMBERS on the remote control.
Follow the steps below and on the next page to program channels into
the TV’s memory.
Programming channels automatically
Your TV can automatically detect all active channels in your area
and store them in the TV’s memory. After the channels are stored
automatically, you can manually add or erase individual channels
(see page 17).
To program channels automatically:
1. Press MENU.
2. Press x or • to highlight the SET UP menu.
3. Press y or z to highlight TV/CABLE.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Press x or • to highlight TV (if you use an antenna) or CABLE
(if you use cable).
POWER
RECALL
MUTE
5. Press z to highlight CH PROGRAM.
o
3
6
1
4
2
5
8
0
SET UP
SET UP
LANGUAGE:
LANGUAGE:
[ENGLISH] FRANCAIS ESPANOL
[ENGLISH] FRANCAIS ESPANOL
TV/CABLE:
[TV] CABLE
TV/CABLE:
[TV] CABLE
CHANNEL
NUMBERS
CH PROGRAM
ADD/ERASE:
V-CHIP CONTROL
MORE
CH PROGRAM
ADD/ERASE:
V-CHIP CONTROL
MORE
[ADD] ERASE
[ADD] ERASE
9
7
CH RTN
[
]
[
]
[
]
[
]
MOVE
SELECT
MOVE
SELECT
100
ENT
6. Press x or • to start automatic channel programming (“CH
PROGRAM” displays on-screen). The TV automatically cycles
through every TV or cable channel (depending on which you
selected), and stores all active channels in the TV’s memory.
MENU
CH
MENU/
ENTER
VOL
VOL
yz x •
7. When automatic channel programming is complete, the message
CH
“CH Programming Completed” appears.
TV
CABLE
VCR
CHANNEL yz
8. Press CHANNEL ▲▼ to view the programmed channels.
EXIT
EXIT
Adding and erasing channels manually
After you have automatically programmed the channels into the TV’s
memory, you can manually add and erase individual channels.
To add a channel to or erase a channel from the TV’s memory:
1. Tune the TV to the channel you want to add or erase. If you are
adding a channel, you will need to use the CHANNEL
NUMBERS to select the channel.
2. Press MENU.
3. Press x or • to highlight the SET UP menu.
4. Press y or z to highlight ADD/ERASE.
SET UP
LANGUAGE:
[ENGLISH] FRANCAIS ESPANOL
TV/CABLE:
[TV] CABLE
CH PROGRAM
ADD/ERASE: [ADD] ERASE
V-CHIP CONTROL
MORE
[
]
[
]
MOVE
SELECT
5. Press x or • to highlight ADD or ERASE, whichever function you
want to perform.
6. Press MENU.
7. Repeat steps 1–6 for other channels you want to add or erase,
or press EXIT to return to normal TV viewing.
Changing channels
To change to the next programmed channel:
Press CHANNEL yz.
To change to a specific channel (programmed or unprogrammed):
Press the CHANNEL NUMBERS (0–9 and 100).
Note: For channels 100 and higher, press the 100 button, and then
the next two channel numbers (for example, to select channel 100,
press 100, 0, 0; to select channel 125, press
100, 2, 5).
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the TV’s features
Adjusting the channel settings
POWER
RECALL
MUTE
Switching between two channels
o
You can switch between two channels without entering an actual channel
number each time.
3
6
1
4
2
5
8
0
To switch between two channels:
1. Select the first channel you want to view.
CHANNEL
NUMBERS
9
7
2. Select a second channel using the CHANNEL NUMBERS
CH RTN
(0–9 and 100).
CH RTN
MENU
100
ENT
3. Press CH RTN (channel return). The previous channel will display.
Every time you press CH RTN, the TV will switch back and forth
between the last two channels you tuned the TV to.
CH
MENU/
ENTER
VOL
VOL
yz x •
Programming your favorite channels
CH
The Favorite Channel feature allows you to use the FAV CH ▼▲
buttons on the remote control to cycle through your favorite channels,
skipping over channels you do not normally watch. You can program a
maximum of 12 favorite channels.
TV
CABLE
VCR
CHANNEL yz
EXIT
EXIT
FAV CH
TV/VIDEO
A
FAV CH zy
Note: You can still use CHANNEL ▲▼ to cycle through all the channels
you previously programmed into the TV’s memory (see “Programming
channels in to the TV’s memory” on page 16).
REC TV/VCR STOP
PLAY
FF
STILL SOURCE PIP
SLOW PAUSE REW
PIP CH
LOCATE SWAP
To program your favorite channels:
1. Tune the TV to a channel you want to program as a favorite
channel.
CT-90037
2. Press MENU.
3. Press x or • to highlight the SET UP menu.
4. Press y or z to highlight FAVORITE CH.
SET UP
MORE
TIMER:
DEMO:
0 MIN
START [STOP]
FAVORITE CH
[
]
[
]
MOVE
START
5. Press x or • to display the FAVORITE CH menu.
6. Press x or • to highlight SET.
7. Press z to add the current channel to the list.
8. Press EXIT.
SET UP
FAVORITE CH
[SET] CLEAR
2
0
0
5
0
0
6
0
0
11
0
0
[TV: CYAN, CABLE: BLUE]
[
]
[
]
SELECT
SET
9. Repeat steps 1–8 for up to 12 channels.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
To select your favorite channels:
Press FAV CH zy on the remote control to cycle through the
MENU
favorite channels you programmed.
CH
Note: The FAV CH zy buttons will not work unless you program
at least one favorite channel.
MENU/
ENTER
VOL
VOL
yz x •
To clear a favorite channel:
CH
1. Tune the TV to the channel you want to clear from your favorite
channel list.
TV
CABLE
VCR
EXIT
EXIT
2. Press MENU.
FAV CH
TV/VIDEO
A
3. Press x or • to highlight the SET UP menu.
4. Press y or z to highlight FAVORITE CH.
5. Press x or • to display the FAVORITE CH menu.
6. Press x or • to highlight CLEAR.
FAV CH zy
REC TV/VCR STOP
PLAY
FF
STILL SOURCE PIP
SLOW PAUSE REW
PIP CH
LOCATE SWAP
CT-90037
SET UP
FAVORITE CH
SET [CLEAR]
2
0
0
5
0
0
6
0
0
0
0
0
[TV: CYAN, CABLE: BLUE]
[
]
[
]
SELECT
CLEAR
7. Press z to clear the current channel number from the list.
8. Press EXIT.
9. Repeat steps 1–8 for other channels you want to clear from your
favorite channel list.
Using the V-Chip Control (blocking) feature
You can use the V-Chip Control feature to block certain programs or
channels, to prevent others from viewing them.
Selecting a PIN code
Before you can block programs or channels, you must select a personal
identification number (PIN) code. Your PIN code allows you to access
the V-Chip Control menu, and prevents others from changing the rating
and blocking limits you set.
To select your PIN code and access the V-Chip Control menu:
1. Press MENU.
2. Press x or • to highlight the SET UP menu.
3. Press y or z to highlight V-CHIP CONTROL.
4. Press x or • to display the new PIN code entering screen.
SET UP
SET UP
LANGUAGE:
[ENGLISH] FRANCAIS ESPANOL
TV/CABLE:
CH PROGRAM
ADD/ERASE:
BLOCKING IS RESET
PLEASE ENTER NEW PIN CODE
_ _ _ _
[TV] CABLE
[ADD] ERASE
V-CHIP CONTROL
MORE
[
]
SELECT [0–9] END [EXIT]
[
]
MOVE
START
(Continued on next page)
19
Download from Www.Somanuals.com. All Manuals Search And Download.
(Continued from previous page)
POWER
RECALL
MUTE
5. Use the CHANNEL NUMBERS (0–9) to enter your four-digit
PIN code. After the code is entered, the V-Chip Control menu
appears.
o
RECALL
3
6
1
4
2
5
8
0
SET UP
CHANNEL
NUMBERS
ENABLE BLOCKING [Y] N
SET RATING
SET BLOCKING OPTIONS
NEW PIN CODE
9
7
CH RTN
BLOCK CHANNEL
100
ENT
[
]
[
]
MOVE
SELECT
MENU
V-Chip Control (Blocking) Menu
CH
6. Press y or z to highlight ENABLE BLOCKING.
MENU/
ENTER
VOL
VOL
yz x •
7. Press x or • to highlight “Y,” which enables all blocking by activat-
ing the V-Chip. See “Blocking programs by ratings” on page 21,
“Blocking unrated movies and programs” on page 23.
CH
TV
CABLE
VCR
EXIT
Note: The “Blocking channels” feature (page 24) is not affected by the
EXIT
“Enable Blocking” setting.
To disable blocking:
Highlight “N” in step 7, above, to deactivate the V-Chip Control
feature and disable blocking.
If you forget your PIN code
1. Press MENU.
2. Press x or • to highlight the SET
Changing your PIN code
1. Press MENU.
2. Press x or • to highlight the SET UP menu.
3. Press y or z to highlight V-CHIP CONTROL.
4. Press x or • to display the PIN code entering screen.
UP menu.
3. Press y or z to highlight V-CHIP
CONTROL.
5. Use the Channel Number buttons (0–9) to enter your existing PIN
4. Press x or • to display the PIN
code. After the code is entered, the V-Chip Control menu appears.
code entering screen.
6. Press y or z to highlight NEW PIN CODE.
5. While the PIN code entering
screen is displayed, press RECALL
four times within five seconds. The
“Blocking Is Reset” screen appears.
7. Press x or • to display the New PIN Code entering screen.
SET UP
SET UP
ENABLE BLOCKING
SET RATING
SET BLOCKING OPTIONS
NEW PIN CODE
BLOCK CHANNEL
[Y] N
PLEASE ENTER NEW PIN CODE
_ _ _ _
SET UP
BLOCKING IS RESET
PLEASE ENTER NEW PIN CODE
_ _ _ _
SELECT [0–9] END [EXIT]
[
]
[
]
MOVE
SELECT
SELECT [0–9] END [EXIT]
8. Use the CHANNEL NUMBERS (0–9) to enter a new PIN code.
After the new code is entered, the V-Chip Control menu appears.
6. Use the CHANNEL NUMBERS
(0–9) to enter a new PIN code.
After the new code is entered, the
V-Chip Control menu appears.
9. Press EXIT to return to normal TV viewing.
7. Press EXIT to return to normal TV
viewing.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Blocking programs by ratings
Note:
The Motion Picture Association of America (MPAA)
uses a rating system to qualify motion picture content.
Television broadcasters employ a similar rating system
to qualify the content of television programs. The
MPAA, Youth TV, and TV ratings work with the
V-Chip feature to allow you to block access to programs
that exceed the rating limits you set.
Press RECALL to see the rating
of the program you are viewing.
Not all programs are rated,
however. To block programs or
movies that are not rated, see
“Blocking unrated movies and
programs” on page 23.
STEREO
TV-PG
L
V
TV 6
Ratings definitions
MPAA Ratings
TV Ratings
MA
Mature audience only. This program is specifically
designed to be viewed by adults and therefore may be
unsuitable for children under 17.
Dialog
Language
Sex
X
For adults only.
NC17
R
Not intended for anyone 17 or under.
Restricted. Under 17 requires an accompanying
parent or adult guardian.
Intensely suggestive dialog
Crude or indecent language
Explicit sexual activity
Graphic violence
PG13
PG
Parents strongly cautioned. Some material may not
be appropriate for children under 13.
Violence
Parental guidance suggested. Some material may
not be appropriate for children.
14
Parents strongly cautioned. This program contains
some material that many parents would find unsuitable
for children under 14 years of age.
G
General audience. Appropriate for all ages.
Dialog
Language
Sex
Frequent suggestive dialog
Frequent coarse language
Intense sexual situations
Intense violence
Youth TV Ratings
Y7, Y7FV
Directed to older children. Programs rated Y7 are
designed for children 7 and above. Programs rated
Y7FV contain fantasy violence that may be more
intense or combative than Y7-rated programs.
Violence
PG
Parental guidance suggested. This program contains
material that parents may find unsuitable for younger
children.
Y
For all children. Programs rated Y are designed to
be appropriate for all children.
Dialog
Language
Sex
Some suggestive dialog
Occasional coarse language
Some sexual situations
Moderate violence
Violence
G
General audience. Most parents would find this
program suitable for all ages.
No DLSV
Programs without any Dialog, Language, Sex, or
Violence ratings.
To block programs by rating:
1. Press MENU.
POWER
RECALL
MUTE
2. Press x or • to highlight the SET UP menu.
3. Press y or z to highlight V-CHIP CONTROL.
4. Press x or • to display the PIN code entering screen.
o
RECALL
3
6
1
4
2
5
8
0
5. Use the CHANNEL NUMBERS (0–9) to enter your four-digit
PIN code. After the code is entered, the V-Chip Control menu
appears.
CHANNEL
NUMBERS
9
7
6. Press y or z to highlight ENABLE BLOCKING.
CH RTN
100
ENT
7. Press x or • to highlight “Y,” which enables all blocking by
activating the V-Chip. (Note: Highlight “N” to deactivate the
V-Chip Control feature and disable blocking.)
MENU
CH
MENU/
ENTER
VOL
VOL
yz x •
SET UP
ENABLE BLOCKING [Y] N
SET RATING
CH
SET BLOCKING OPTIONS
NEW PIN CODE
BLOCK CHANNEL
TV
CABLE
VCR
EXIT
[
]
[
]
MOVE
SELECT
21
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Press y or z to highlight SET RATING.
9. Press x or • to display the Set Rating menu.
POWER
RECALL
MUTE
o
10. Press y or z to highlight MPAA Rating, Youth TV Rating, or
MUTE
TV Rating.
3
6
1
4
2
5
8
0
11. Press • to select (or x to deselect) the ratings to be blocked. Blocked
ratings will be marked with “x”; unblocked ratings will will be
marked with “✔.” All ratings higher than the ones that are selected
are blocked as well. For example, if you block the MPAA rating R,
programs with the higher ratings NC17 and X also will be blocked.
9
7
CH RTN
100
ENT
MENU
SET UP
SET UP
CH
MPAA RATING:
TV RATING:
DIALOG:
MA 14 PG
x
G
X
NC17 R PG13 PG
G
MENU/
ENTER
x x
VOL
VOL
LANGUAGE:
SEX:
yz x •
YOUTH TV RATING:
VIOLENCE:
NO DLSV:
Y
Y7FV Y7
BACK TO V-CHIP MENU
TV RATING
CH
[
]
[
]
[
]
[
]
MOVE
SELECT
MOVE
SELECT
TV
CABLE
VCR
EXIT
EXIT
12. When you finish selecting the program ratings to be blocked:
• To return to the V-Chip menu, press y or z to highlight
BACK TO V-CHIP MENU, and then press x or •.
• To return to normal TV viewing, press EXIT.
Unblocking programs temporarily
When you try to view a program with a ratings block, a message appears
stating that the program has been blocked because the program’s rating
exceeds the set limits. To temporarily override the block and view the
program, press MUTE and enter your PIN code. To reset your original
ratings blocks, turn the TV off and then on again.
Note:
After unblocking programs temporarily, all
programs will be unblocked until the TV is
turned off. The TV will enter blocked mode
when it is turned on again.
THIS PROGRAM HAS BEEN BLOCKED!
TV-PG
BLOCKING IS ACTIVE
PLEASE ENTER PIN CODE
TO TE_MP_OR_AR_ILY UN-BLOCK
L
V
EXCEEDS SET LIMITS
PUSH MUTE TO ENTER PIN
SELECT [0–9] END [EXIT]
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Blocking unrated movies and programs
POWER
Some movies and programs are not rated. You can use the V-Chip
Control feature to block unrated movies and programs.
RECALL
MUTE
o
To block unrated movies and programs:
1. Press MENU.
2. Press x or • to highlight the SET UP menu.
3. Press y or z to highlight V-CHIP CONTROL.
4. Press x or • to display the PIN code entering screen.
3
6
1
4
2
5
8
0
CHANNEL
NUMBERS
9
7
CH RTN
100
ENT
5. Use the CHANNEL NUMBERS (0–9) to enter your four-digit
PIN code. After entering the code, the V-Chip Control menu
appears.
MENU
CH
6. Press y or z to highlight ENABLE BLOCKING.
MENU/
ENTER
VOL
VOL
yz x •
7. Press x or • to highlight “Y,” which enables all blocking by activat-
ing the V-Chip. (Note: Highlight “N” to deactivate the V-Chip
feature and disable blocking.)
CH
TV
CABLE
VCR
8. Press y or z to highlight SET BLOCKING OPTIONS.
EXIT
EXIT
9. Press x or • to display the unrated movie/program blocking menu.
10. Press y or z to highlight BLOCK MPAA UNRATED (to block
unrated movies) or BLOCK TV NONE RATING (to block unrated
TV programs).
11. Press x or • to highlight “Y” to block movies/programs rated
“TV None.” (Note: Highlight “N” to unblock unrated programs.)
12. Press EXIT to return to normal TV viewing.
SET UP
SET UP
ENABLE BLOCKING
SET RATING
[Y] N
BLOCK MPAA UNRATED:
[Y] N
[Y] N
Note:
BLOCK TV NONE RATING:
BACK TO V-CHIP MENU
Blocking unrated TV programs (those rated “TV
NONE”) also may block emergency messages.
SET BLOCKING OPTIONS
NEW PIN CODE
BLOCK CHANNEL
NOTICE: ENABLING THIS OPTION
MAY BLOCK EMERGENCY
MESSAGES
[
]
[
]
[
]
[
]
MOVE
SELECT
MOVE
SELECT
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Blocking channels
POWER
You can block a maximum of four TV channels and four cable channels.
Blocked channels cannot be viewed, regardless of their programs’ ratings.
If you try to tune the TV to a blocked channel, the nearest unblocked
channel will display.
RECALL
MUTE
o
3
6
1
4
2
5
8
0
To block a channel:
1. Tune the TV to the channel you want to block.
2. Press MENU.
3. Press x or • to highlight the SET UP menu.
4. Press y or z to highlight V-CHIP CONTROL.
5. Press x or • to display the PIN code entering screen.
CHANNEL
NUMBERS
9
7
CH RTN
100
ENT
MENU
CH
6. Use the CHANNEL NUMBERS (0–9) to enter your four-digit
PIN code. After entering the code, the V-Chip Control menu
appears.
MENU/
ENTER
VOL
VOL
yz x •
CH
7. Press y or z to highlight BLOCK CHANNEL.
TV
CABLE
VCR
8. Press x or • to display the BLOCK CHANNEL menu.
EXIT
EXIT
SET/CLEAR will be highlighted.
9. Press x or • to highlight SET.
10. Press z to add the current channel to the list.
SET UP
Note:
BLOCK CHANNEL
[SET] CLEAR
After programming CHANNEL BLOCK, be
sure to tune the TV to a channel that is not
blocked before turning the TV off.
0
0
0
6
[
]
[
]
SELECT
SET
END [EXIT]
11. Press EXIT.
12. Repeat steps 1–11 to block additional channels.
To unblock all blocked channels:
Note: This will unblock every channel you have blocked. You cannot
unblock individual channels.
1. Press MENU.
2. Press x or • to highlight the SET UP menu.
3. Press y or z to highlight V-CHIP CONTROL.
4. Press x or • to display the PIN code entering screen.
5. Use the CHANNEL NUMBERS (0–9) to enter your four-digit
PIN code. After entering the code, the V-Chip Control menu
appears.
6. Press y or z to highlight BLOCK CHANNEL.
7. Press x or • to display the BLOCK CHANNEL menu.
SET/CLEAR will be highlighted.
8. Press x or • to highlight CLEAR.
9. Press z to clear all blocked channels from the list.
10. Press EXIT.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the picture
POWER
RECALL
MUTE
Adjusting the picture quality
o
You can adjust the picture’s contrast, brightness, sharpness, color, and
tint. Your picture quality adjustments are stored automatically in the
TV’s memory. You can keep these settings or choose preset options in
the PREFERENCE menu (see “Selecting the color temperature”
below, and “Adjusting the picture preference” on the next page.)
3
6
1
4
2
5
8
0
9
7
To adjust the picture quality:
1. Press MENU.
CH RTN
100
ENT
2. Press x or • to highlight the PICTURE menu.
3. Press y or z until the quality you want to adjust is highlighted.
MENU
CH
MENU/
ENTER
VOL
VOL
yz x •
PICTURE
CH
Note:
–
+
CONTRAST 50
BRIGHTNESS 50
SHARPNESS 50
COLOR
TINT
TV
CABLE
VCR
To reset the picture (and audio)
adjustments to the factory settings,
select RESET in the PICTURE menu,
and then press •.
EXIT
50
0
RESET
[
]
[
]
MOVE
ADJUST
4. Press x or • to adjust the level, as described in the following table:
Selection
Pressing
Contrast
Brightness
Sharpness
Color
Lower
Higher
Darker
Softer
Paler
Lighter
Sharper
Deeper
Greenish
Tint
Reddish
Selecting the color temperature
Change the picture quality by selecting from three preset color
temperatures—cool, medium, and warm.
To select the color temperature:
1. Press MENU.
2. Press x or • to highlight the PREFERENCE menu.
3. Press y or z to highlight COLOR TEMPERATURE.
PREFERENCE
COLOR TEMPERATURE
[COOL] MEDIUM WARM
PICTURE PREFERENCE
[SPORTS] STANDARD MOVIE MEMORY
[
]
[
]
MOVE
SELECT
4. Press x or • to highlight the mode you prefer, as described in the
following table:
Mode
Picture Quality
Cool
Medium
Warm
Blueish
Neutral
Reddish
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the picture preference
POWER
You can select from four picture modes—Sports, Standard, Movie, and
RECALL
MUTE
Memory.
o
RECALL
To adjust the picture preference:
3
6
1
4
2
5
8
0
1. Press MENU.
2. Press x or • to highlight the PREFERENCE menu.
3. Press y or z to highlight PICTURE PREFERENCE.
9
7
CH RTN
100
ENT
PREFERENCE
COLOR TEMPERATURE
[COOL] MEDIUM WARM
MENU
PICTURE PREFERENCE
[SPORTS] STANDARD MOVIE MEMORY
CH
MENU/
ENTER
VOL
VOL
yz x •
[
]
[
]
MOVE
SELECT
CH
4. Press x or • to highlight the mode you prefer, as described in the
TV
CABLE
VCR
following table:
EXIT
EXIT
Mode
Picture Quality
Sports
Bright and dynamic picture (factory-set)
Standard Standard picture quality (factory-set)
Movie
Movie-like picture setting (factory-set)
Memory Your personal preferences (set by you; see
Adjusting the picture quality” on previous page)
Displaying on-screen information
Press RECALL to display the following
information on-screen:
STEREO
TV-PG
L
V
• Audio status (stereo or SAP)
• Rating of current program (if rated)
• Channel number or video mode
TV 6
Setting the off timer
The off timer automatically turns off the TV after a set amount of time.
To set the off timer:
1. Press MENU.
2. Press x or • to highlight the SETUP menu.
3. Press y or z to highlight TIMER.
SET UP
MORE
4. Press • to increase (or x to decrease) the amount
TIMER:
DEMO:
FAVORITE CH
30 MIN
START [STOP]
of time until the TV turns off automatically (in
10-minute increments, to a maximum of 180).
5. Press EXIT to exit the menu and return to
[
]
[
]
MOVE
START
normal TV viewing.
To cancel the off timer:
Set the off timer to 0 (zero) minutes in step 4 above, or turn off
the TV.
Auto power off
The TV turns off automatically after approximately 15 minutes if it is
tuned to a vacant channel or a station that stops broadcasting for the day.
Note: The auto power off feature does not work in VIDEO mode.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the closed caption feature
The Closed Caption feature has two options:
POWER
RECALL
MUTE
• Captions—An on-screen display of the dialogue, narration, and
sound effects of programs and videos that are closed-captioned
(usually identified in your local TV listing as “CC”).
o
3
6
1
4
2
5
8
0
• Text—An on-screen display of information not related to the
program, such as weather or stock data (if available in your
viewing area).
9
7
To view captions or text:
1. Tune the TV to the desired program.
CH RTN
100
ENT
2. Press MENU, and then press x or • to highlight the CLOSED
MENU
CAPTION menu.
CH
3. Press y or z to highlight CC.
MENU/
ENTER
VOL
VOL
yz x •
CH
CLOSED CAPTI0N
TV
CABLE
VCR
CC:
C1 C2 C3 C4 T1
T2 T3 T4 [OFF]
EXIT
[
]
[
]
MOVE
SELECT
4. Press x or • to select the desired Closed Caption mode, as
follows:
Note:
A closed caption signal may not display in the
following situations:
• To view captions, select C1, C2, C3, or C4 (C1 displays
translation of the primary language in your area). Note: If the
program or video you selected is not closed-captioned, no
captions will display on-screen.
• when a videotape has been dubbed
• when the signal reception is weak
• when the signal reception is non-standard
The top of the mountain is covered
with snow all the year round.
• To view text, select T1, T2, T3, or T4. Note: If text is not
available in your viewing area, a black rectangle may appear
on-screen. If this happens, set the Closed Caption feature to OFF.
WORLD WEATHER
Temps
F
Current
Weather
Clear
C
LONDON
MOSCOW
PARIS
51
11
14
12
19
18
Cloudy
Clear
57
53
66
ROME
TOKYO
Cloudy
Rain
65
• To turn the Closed Caption feature off, highlight OFF in the
Closed Caption menu.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the sound
Muting the sound
MUTE
Press MUTE to temporarily turn off the sound. While the sound is off,
the screen displays the word “MUTE” in the lower right corner. To
restore the sound, press MUTE or VOL x •.
POWER
RECALL
MUTE
o
RECALL
3
6
1
4
2
5
8
0
When you press MUTE, the Closed Caption feature is automatically
activated. To deactivate captions and restore normal sound, press
MUTE again. This feature works only when the Closed Caption mode
is set to OFF. For more information about closed caption settings, see
“Using the closed captioned feature” on page 27.
9
7
CH RTN
100
ENT
Selecting stereo/SAP broadcasts
MENU
The multi-channel TV sound (MTS) feature provides high-fidelity
stereo sound. MTS also can transmit a second audio program (SAP)
containing a second language or other audio information.
CH
MENU/
ENTER
VOL
VOL
yz x •
Note: The MTS feature is not available in VIDEO mode.
CH
When the TV receives a stereo or SAP broadcast, the word “STEREO”
or “SAP” displays on-screen every time you turn the TV on, change
the channel, or press RECALL.
TV
CABLE
VCR
VOL x •
EXIT
To listen to stereo sound:
1. Press MENU.
2. Press x or • to highlight the AUDIO menu.
3. Press y or z to highlight MTS.
4. Press x or • to highlight STR (stereo).
Note: If the stereo sound is noisy, select MONO to reduce the
noise.
AUDIO
MTS:
[STR] SAP MONO
50
50
0
BASS
TREBLE
BALANCE
SURROUND: [ON] OFF
[
]
[
]
MOVE
SELECT
Note: In general, if you leave the TV in stereo (STR) mode, the TV will
automatically output the type of sound being broadcast (stereo or mono).
To listen to a second audio program (SAP):
1. Press MENU.
2. Press x or • to highlight the AUDIO menu.
3. Press y or z to highlight MTS.
4. Press x or • to highlight SAP. The TV speakers will output the
second audio program (if available), instead of normal audio.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the sound quality
You can change the sound quality of your TV by adjusting the bass,
treble, and balance.
Note:
To reset the audio adjustments (bass, treble,
and balance) to the factory settings, select
RESET in the PICTURE menu (see note on
page 25).
To adjust the sound quality:
1. Press MENU.
2. Press x or • to highlight the AUDIO menu.
3. Press y or z to highlight the quality you want to adjust (BASS,
TREBLE, or BALANCE).
4. Press x or • to adjust the level:
POWER
RECALL
MUTE
o
• x makes the sound quality weaker or increases the balance in
the right channel, depending on the item selected.
3
6
1
4
2
5
8
0
• • makes the sound quality stronger or increases the balance in
the left channel, depending on the item selected.
9
7
CH RTN
AUDIO
MTS:
[STR] SAP MONO
100
ENT
–
+
BASS
TREBLE
BALANCE
50
50
0
MENU
SURROUND: [ON] OFF
CH
[
]
[
]
MOVE
ADJUST
MENU/
ENTER
VOL
VOL
yz x •
CH
Using the surround sound feature
TV
CABLE
VCR
The surround sound feature expands the audio listening field wider and
deeper to create exceptional sound quality from the TV speakers.
This feature uses stereo signals from a TV broadcast or video input.
EXIT
To turn surround sound on:
1. Press MENU.
2. Press x or • to highlight the AUDIO menu.
3. If you have not already done so, select STEREO mode (press y or
z to highlight MTS, and then press x or • to highlight STR).
4. Press y or z to highlight SURROUND.
5. Press x or • to highlight ON.
AUDIO
MTS:
[STR] SAP MONO
BASS
TREBLE
BALANCE
50
50
0
SURROUND: [ON] OFF
[
]
[
]
MOVE
SELECT
To turn surround sound off:
Highlight OFF in step 5 above.
Note: In general, if you leave the surround sound feature ON, the TV will
automatically output the type of sound being broadcast (surround stereo or
mono).
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Viewing the demonstration (DEMO) mode
The DEMO mode automatically demonstrates several features of
your TV.
POWER
RECALL
MUTE
POWER
RECALL
o
To start the DEMO mode:
3
6
1
4
1. Press MENU.
2. Press x or • to highlight the SET UP menu.
3. Press y or z to highlight DEMO.
2
5
8
0
9
7
CH RTN
100
ENT
SET UP
MORE
TIMER:
MENU
0 MIN
DEMO [START] STOP
FAVORITE CH
CH
MENU/
ENTER
VOL
VOL
yz x •
[
]
[
]
MOVE
SELECT
CH
TV
CABLE
VCR
4. Press x or • to highlight START.
EXIT
EXIT
5. Press MENU to start the demo.
To stop the DEMO mode:
Press RECALL, EXIT, or POWER.
Understanding the last mode memory feature
If the power is cut off while you are viewing the TV, the Last Mode
Memory feature automatically turns on the TV when the power is
resupplied.
If the power is going to be off for a long time and you are going to be
away from your TV, unplug the power cord to prevent the TV from
turning on in your absence.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Specifications
Television system
NTSC standard
Channel coverage
VHF: 2 through 13
UHF: 14 through 69
Cable TV: mid band (A-8 through A-1, A through I)
super band (J through W)
hyper band (AA through ZZ, AAA, BBB)
ultra band (65 through 94, 100 through 125)
Power source
120V AC, 60Hz
Power consumption
Audio power
102 W (average)
5W + 5W
Speaker type
2-3/8 x 4-3/4 inches (60 x 120 mm)
Audio/Video terminals
S-VIDEO INPUT
Y-INPUT: 1V (p-p), 75 ohm, negative sync.
C-INPUT: 0.286V (p-p) (burst signal), 75 ohm
AUDIO/VIDEO INPUT
VIDEO: 1V(p-p), 75 ohm, negative sync.
AUDIO: 150mV(rms) (30% modulation equivalent, 47k ohm)
ColorStream® (component video) INPUT
Y: 1V (p-p), 75 ohm
C
R
(PR): 0.7 V (p-p), 75 ohm
(PB): 0.7 V (p-p), 75 ohm
CB
AUDIO/VIDEO OUTPUT
VIDEO: 1V(p-p), 75 ohm, negative sync.
AUDIO: 150mV(rms) (30% modulation equivalent, 4.7k ohm)
Dimensions
Width
Height
Depth
34 inches (864mm)
27-1/2 inches (699mm)
21-1/8 inches (537mm)
Mass
111 lbs (50,3kg)
Supplied accessories
Optional TV stand
Remote Control with 2 size “AA” batteries
ST3242
Design and specifications are subject to change without notice.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Before calling service personnel, please check the following chart for a possible cause of the problem you are experiencing.
A minor adjustment on your part may eliminate the problem and restore your TV reception.
Problem
Checks and Adjustments
●
TV will not turn on
Make sure the power cord is plugged in, and then press POWER.
●
The remote control batteries may be dead. Replace the batteries.
●
No picture, no sound
No sound, picture OK
Check the antenna/cable connections.
●
The sound may be muted. Press VOLUME S.
●
The station may have broadcast difficulties. Try another channel.
●
Make sure the MTS feature is set correctly.
●
Poor sound, picture OK
Poor picture, sound OK
The station may have broadcast difficulties. Try another channel.
An appliance near the TV may be causing interference. Move or
turn off the appliance.
●
●
Check the antenna/cable connections.
●
The station may have broadcast difficulties.Try another channel.
●
An appliance near the TV may be causing interference. Move or
turn off the appliance.
●
Adjust the Picture menu.
●
Poor reception of broadcast channels
The station may have broadcast difficulties. Try another channel.
●
Check the antenna connections.
●
If using a VCR, make sure the TV/VCR button is set correctly.
●
No UHF, VHF OK
Make sure the TV/CABLE function is set to the mode that corresponds
to the signal source type (cable company or outside antenna).
●
Black box appears on the screen
Cannot select a certain channel
The Closed Caption Text feature (T1, T2, T3, or T4) may be on.
Set the Closed Caption feature to OFF.
●
The channel may be blocked by the BLOCK CHANNEL function.
Unblock the channel.
●
The channel may have been erased from the channel memory by the
ADD/ERASE function. Reprogram the channel into channel memory
or use the Channel Numbers to select the channel.
●
Multiple images (ghosts)
Poor color or no color
The station may have broadcast difficulties. Try another channel.
Antenna reception may be poor. Use a highly directional outdoor antenna.
●
●
The station may have broadcast difficulties. Try another channel.
●
An appliance near the TV may be causing interference. Move or
turn off the appliance.
●
Adjust the TINT and/or COLOR in the Picture menu.
●
If you change the direction of the TV while the TV is on, the
picture may suffer from color shading. Turn off the TV and allow
it to cool for about 30 minutes; then turn it on again.
●
No stereo or SAP sound from
an MTS broadcast
Make sure the MTS feature is set correctly.
●
The remote control does not operate
Make sure the TV/CABLE/VCR switch is set correctly.
●
There may be an obstruction between the remote control and the TV.
Remove the obstruction and retry the remote control.
●
The remote control batteries may be dead. Replace the batteries.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
35
Download from Www.Somanuals.com. All Manuals Search And Download.
HEAD OFFICE
82 Totowa Road
Wayne, NJ 07470
LATIN AMERICA DIVISION
1900 North West 84th Ave.
Miami, FL 33126 TEL: (305) 470-9355
Toshiba America
Consumer Products, Inc.
Sierra Candela #111, 6to. Piso
Col. Lomas de Chapultepec
C.P. 11000 Del. Miguel Hidalgo
Toshiba de Mexico,
S.A. de C.V.
Mexico, D.F. TEL: (52) (55) 5249-6500 ext. 561
MANUFACTURED BY
TOSHIBA AMERICA CONSUMER PRODUCTS, INC.
ColorStream is a registered trademark of Toshiba America Consumer Products, Inc.
PRINTED IN USA
(02-08) B
Download from Www.Somanuals.com. All Manuals Search And Download.
|