TOPFIELD
TF 7710 HSCI
TF 7720 HSCI
User Guide
High Definition
Digital Satellite Receiver
Common Interface
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents iii
Contents
1
1
2
3
4
5
7
7
7
9
Download from Www.Somanuals.com. All Manuals Search And Download.
iv Contents
16
26
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
v
46
52
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
1
Chapter 1
Introduction
The TF 7710 HSCI/TF 7720 HSCI digital receiver is fully com-
pliant with the international Digital Video Broadcasting (DVB)
standard, and can receive digital broadcasts. For its operation
you need an antenna, which must be installed appropriately.
NOTE
In general we equate a channel with a frequency. Unlike ana-
logue broadcasts, however, digital broadcasts are not all as-
signed to their own frequencies; instead, multiple television
broadcasts are transmitted through a single frequency. The fre-
quency in digital broadcasting is usually called transponder. To
reduce confusion in this manual, the word service is preferably
used than channel as a term to indicate one television or radio
broadcast.
1.1 Features
The TF 7710 HSCI/TF 7720 HSCI digital receiver has the follow-
ing features:
•
Supports DiSEqC 1.0, DiSEqC 1.1, DiSEqC 1.2 and US-
ALS.
Download from Www.Somanuals.com. All Manuals Search And Download.
2
Introduction
• Can store up to 5000 television and radio services.
• You can edit the services list.
• You can create favourite lists of your favourite services.
•
•
•
You can view information about the current television or
radio programme.
Has an electronic programme guide that provides an
overview of scheduled programmes.
You can update the firmware of the digital receiver to the
latest version, provided by the manufacturer.
1.2 Controlling the digital receiver
The digital receiver can be operated with the remote control
and the buttons on the front panel.
NOTE
When the digital receiver is off but plugged into a wall outlet,
we say that it is in standby mode; on the other hand, when it is
on, it is in operation mode. Even when you are not using the
digital receiver, you should keep it plugged into a wall outlet
to be in standby mode so that it can run timer events at any
time.
Download from Www.Somanuals.com. All Manuals Search And Download.
1.2 Controlling the digital receiver
3
1.2.1 The front panel
The front panel of the digital receiver has buttons to control the
digital receiver, and specific lamps and a display to indicate its
status. The following indicates what they mean.
TV/STB
REMOTE
STANDBY
CHANNEL
VOLUME
STANDBY
STANDBY button switches the digital receiver between
standby mode and operation mode.
CHANNEL
,
buttons switch to previous or next service.
They are also used to navigate in menus and interactive
screens.
VOLUME
,
buttons decrease or increase the volume.
They are also used to change values for menu options.
TV/STB lamp lights up while your video recorder operates
instead of the digital receiver. See
details.
§
3.2.2 for more
REMOTE lamp lights up whenever you press a button on
the remote control.
STANDBY lamp lights up while the digital receiver is in
standby mode.
Front display displays the current time in standby mode,
and displays the current service in operation mode.
Pull the right edge of the front panel to open the flap. You have
to insert your subscription card into the front slot to watch pay
services.
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Introduction
1.2.2 The remote control
1
ꢀ
button switches the digital re-
ceiver between standby mode and
operation mode.
1
2
14
15
3
4
16
2
ꢀ
pauses live television.
£
3
ꢀ
V.Format changes video resolution.
¢
5
17
18
4
ꢀ
Numeric buttons are used to en-
ter a service number for service
change or to specify values for
menu options.
6
7
19
20
8
9
21
5
ꢀ
switches between the current
service and the previously viewed
one.
10
10
22
20
11
12
13
6
ꢀ
displays teletext.
7
ꢀ
is used to select an audio track
and a sound mode, or a video
track of multifeed programme.
23
£
8
ꢀ
MENU displays the main menu. It
is also used to return to the previ-
ous menu from a submenu.
¢
¡
£
9
ꢀ
OK displays the services list. See
¢
§
used to select a menu item.
£
£
10
ꢀ
V−
,
V+ buttons decrease or increase the volume. They
¢
¡¢
¡
are also used to change values for menu options.
£
11
ꢀ
12
ꢀ
EXIT is used to exit the current screen.
¢
¡
These buttons have different functions per menu. They
will be guided by on-screen help.
Download from Www.Somanuals.com. All Manuals Search And Download.
1.3 What is common interface?
5
£
13
ꢀ
SAT displays the satellite list.
¢
¡
14
ꢀ
mutes the sound. Press again to switch it back on.
£
15
ꢀ
¢
¡
16
ꢀ
switches between television services and radio ser-
vices.
£
17
ꢀ
FAV displays the favourite lists.
¢
¡
18
ꢀ
is used to select a subtitle track.
19
ꢀ
is used to set a sleep timer.
£
£
20
ꢀ
P−
,
P+ buttons switch to previous or next service.
¢
¡ ¢
¡
They are also used to navigate in menus and interactive
screens.
£
21
ꢀ
GUIDE displays the electronic programme guide.
¢
¡
22
ꢀ
displays the service information box. It is also used to
display more information about a programme.
£
23
ꢀ
AUX switches the output of the TV SCART socket be-
tween the digital receiver and the device connected to
¢
¡
1.3 What is common interface?
Some broadcasts are scrambled so that only paid
subscribers can enjoy them. Scrambled services
can only be viewed with a Conditional Access
Module (CAM) and a subscription card belong-
ing with the scrambling system.
Common Interface (CI) is the slot on a digitial
receiver into which a conditional access module
may be insterted. The front of the digital receiver
has two common interfaces.
To watch a pay service, you should take the following steps:
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Introduction
1. Purchase a conditional access module and a subscription
card for the pay service you want to watch.
2. Insert the subscription card into the conditional access
module.
3. Insert the conditional access module into a common in-
terface on the front of the digital receiver.
To view the information about
the module and subscription
card inserted into the digital re-
ceiver, select the Common Inter-
face menu. You should see a
screen like the left figure.
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Chapter 2
Setup
2.1 Unpacking
Before going any further, check that you have received the
following items with your digital receiver.
• Remote control unit
• Two batteries for the remote control (AAA 1.5 V)
• A copy of this user guide
NOTE
Accessories may vary according to your local area.
2.2 Safety precautions
Please read carefully the following safety precautions.
•
The mains power must be 90 to 250 volts. Check it before
connecting the digital receiver to the wall outlet. For
the power consumption of the digital receiver, refer to
Download from Www.Somanuals.com. All Manuals Search And Download.
8
Setup
•
•
The wall outlet should be near the equipment. Do not
run an extension lead to the unit.
Do not expose the digital receiver to any moisture. The
digital receiver is designed for use indoors only. Use dry
cloth when cleaning the digital receiver.
• Place the digital receiver on a firm and level surface.
•
Do not place the digital receiver close to heat emitting
units or in direct sunlight, as this will impair cooling.
Do not lay any objects such as magazines on the digi-
tal receiver. When placed in a cabinet, make sure there
is a minimum space of 10 centimetres around it. For
the physical specification of the digital receiver, refer to
•
•
Protect the power cord from being walked on or pinched.
If the wires are exposed or the cord is damaged, do not
use the digital receiver and get the cord replaced.
Never open the digital receiver casing under any circum-
stances. The warranty will be void.
• Refer all servicing to a qualified service technician.
Table 2.1: Power specifications
Input voltage
90 to 250 V AC, 50/60 Hz
Power consumption 37 W at maximum in operation
4 W in standby
Table 2.2: Physical specifications
Size
Weight
340× 60× 265 mm
2.37 kg
Operating temperature
Storage relative humidity
0 to 45 °C
5 to 90 %
Download from Www.Somanuals.com. All Manuals Search And Download.
2.3 Rear panel connections
9
2.3 Rear panel connections
The TF 7710 HSCI/TF 7720 HSCI has some connections on the
back panel.
1
6
8
9
VIDEO
LNB IN
TV
Y
L
Pb
Pr
R
YPbPr
SCART
LNB OUT
HDMI
USB
AUDIO
S/PDIF
RS-232
VCR
2
3
4
5
7
10
11
12
Check what connections your television set has in comparison
with the digital receiver.
1
ꢀ
LNB IN
Satellite broadcasting signal input socket.
2
ꢀ
LNB OUT Satellite broadcasting signal output socket
through the LNB IN socket for another digital
receiver.
3
ꢀ
YPbPr ↔ SCART Video output selection switch. See
4
ꢀ
HDMI
USB
Audio and video output socket for the high
definition television set.
5
ꢀ
USB port for firmware update and data trans-
fer.
6
ꢀ
VIDEO
Composite video output socket for the televi-
sion set. (yellow)
7
ꢀ
AUDIO L/R Stereo audio output socket for the television
set or the audio system. (white/red)
8
ꢀ
Y/Pb/Pr
Component video output socket for the tele-
vision set. (green/blue/red)
Download from Www.Somanuals.com. All Manuals Search And Download.
10 Setup
9
ꢀ
TV
Audio and video output socket for the televi-
sion set.
10
ꢀ
VCR
Audio and video input/output socket for the
video cassette recorder or suchlike.
11
ꢀ
S/PDIF
RS-232
Dolby digital output socket for the audio sys-
tem.
12
ꢀ
Serial port for firmware update and data
transfer.
Table 2.3: Connectors specifications
HDMI
High definition video output
Left & right audio output
Dolby digital audio output
VIDEO
AUDIO
YPbPr
TV
composite video (CVBS) output
Left & right audio output
Component video (YUV) output
CVBS/S-Video/RGB video output
Left & right audio output
VCR
CVBS video output
Left & right audio output
CVBS/S-Video/RGB video input for bypass
Left & right audio input for bypass
Dolby digital audio output
S/PDIF
RS-232 115.2 kbps at maximum
USB 2.0
2.4 Connecting up your digital receiver
There are several ways to set up the digital receiver. Set up the
digital receiver suitably to your television and other appliances.
If you have any problem with your setup or need help, contact
your dealer.
Download from Www.Somanuals.com. All Manuals Search And Download.
2.4 Connecting up your digital receiver 11
2.4.1 Connecting the antenna
Whatever sort of connection you have be-
tween the digital receiver and the television,
you need to connect the digital receiver to
your television antenna so that it can receive
digital television services.
Connect the antenna cable to the LNB IN con-
nector.
If you have another digital receiver, you may
link it from the LNB OUT connector.
NOTE
Perhaps you are expecting that the satellite antenna could si-
multaneouly catch all frequencies coming from a satellite and
send them to the digital receiver. However, the satellite an-
tenna only sends the frequencies that it can catch with the LNB
frequency and polarization specified by the digital receiver. So
if you have another digital receiver linked from the LNB OUT
connector, you can only use it limitedly. See
details.
§
4.1 for more
2.4.2 Connecting to your television
Between all the following connectors of the digital receiver, we
recommend you to use the first connector to get best picture
quality. If your television does not have the matching connector,
then use the next connector in the following order for better
picture quality.
1. HDMI connector (HDMI)
2. SCART connector (TV)
3. Component connector (YPbPr)
4. Composite connector (VIDEO)
Download from Www.Somanuals.com. All Manuals Search And Download.
12 Setup
You should configure audio and video settings after connecting
To use the HDMI connector
If you have a high definition television set,
you should use a HDMI cable for best re-
sults. Plug one end of the cable into the HDMI
socket on the digital receiver, and the other
end into the matching socket on your televi-
sion. In this case, you do not have to make
audio connections because the HDMI connec-
tor can output stereo audio or Dolby digital
audio.
To use the SCART connector
For best results with a standard television set,
you should use a SCART cable, plugging one
end into the TV socket on the digital receiver
and the other end into a free SCART socket
on your television.
Some televisions have inputs via Component
connector or S-Video connector rather than
SCART.
If you have such a television, use an appropriate conversion ca-
ble to link the TV socket on the digital receiver to the matching
socket on your television.
If you connect with a standard SCART cable, you do not have
to make audio connections because the SCART connector can
output stereo audio. But if you use a conversion cable, such as
SCART-to-Component, you have to make audio connections.
NOTE
You cannot view high definition video with the SCART connec-
tor.
Download from Www.Somanuals.com. All Manuals Search And Download.
2.4 Connecting up your digital receiver 13
To use the component video connector
You will need to obtain a component video ca-
ble (RCA cable) to use the component video
connector. Plug one end of the cables into the
Y (green), Pb (blue) and Pr (red) sockets on
the digital receiver, and the other end into the
matching sockets on your television.
To use the composite video connector
NOTE
You cannot view high definition video with
the composite video connector.
You will need to obtain a composite video
cable (RCA cable) to use the composite video
connector. Plug one end of the cable into the
VIDEO (yellow) socket on the digital receiver,
and the other end into the matching socket
on your television.
To connect the audio connectors
You will need to obtain an audio cable (RCA
cable) to connect the audio connectors. Plug
one end of the cable into the AUDIO L (white)
and AUDIO R (red) sockets on the digital re-
ceiver, and the other end into the matching
sockets on your television or audio system.
Download from Www.Somanuals.com. All Manuals Search And Download.
14 Setup
To enjoy Dolby digital audio, your televi-
sion or audio system must be able to decode
Dolby digital audio, and you will need to ob-
tain a S/PDIF cable. Plug one end of the
cable into the S/PIDF socket on the digital
receiver, and the other end into the matching
socket on your audio system.
2.4.3 Connecting to your video cassette recorder
The digital receiver can also output video to another appliance
such as a video cassette recorder or video receiver through an
auxiliary SCART connector.
You will need to obtain a SCART cable to use
the auxiliary SCART connector. Plug one end
of the cable into the VCR socket on the digital
receiver, and the other end into the match-
ing socket on your video cassette recorder or
suchlike.
2.5 Switching on for the first time
Now that you have your digital receiver connected, you should
plug it in to a mains socket. Ensure that your television set is
turned on, so that you will be able to see the display from the
digital receiver.
2.5.1 Inserting batteries in the remote control
To insert the batteries, open the battery compartment by remov-
ing the lid, and then insert the batteries observing the polarity,
which is marked on the base of the battery compartment.
If the digital receiver no longer reacts properly to remote con-
trol commands, the batteries may be flat. Be sure to remove
Download from Www.Somanuals.com. All Manuals Search And Download.
2.5 Switching on for the first time 15
used batteries. The manufacturer accepts no liability for the
damage resulting from leaking batteries.
NOTE
Batteries, including those which contain no heavy metals, may
not be disposed of with household waste. Please dispose of
used batteries in an environmentally sound manner. Find out
about the legal regulations which apply in your area.
2.5.2 Powering on and checking picture
Now, press the button in top left corner on the remote
control.
£
If you do not see a picture, try pressing the V.Format button on
the remote control. If after several tries you still get no picture,
check that the television is set to the correct input.
¢
¡
If the picture is good, you can skip to
§
4.1 to search for the
available television and radio services. Otherwise, you may
need to temporarily connect the composite video connector
(VIDEO) to your television set so that you can see the on-screen
menus in order to configure the video settings.
Download from Www.Somanuals.com. All Manuals Search And Download.
16 Preference Settings
Chapter 3
Preference Settings
3.1 Language settings
You can select the language in
which the menu would be dis-
played. In addition to that, you
can select which language of au-
dio track and of subtitle track
should be output.
Select the System Setting
>
Lan-
guage Setting menu. You should
see a screen like the left figure.
Menu language
The digital receiver supports many menu languages: Dutch,
English, German, French, Italian, Russian, Turkish and so forth.
Set the Menu Language option to your desired language. Once
you select a language, the menu will be immediately displayed
in the selected language.
Download from Www.Somanuals.com. All Manuals Search And Download.
3.1 Language settings 17
Subtitle language
Set the 1st Subtitle Language option and the 2nd Subtitle Lan-
guage option to your desired languages. When you watch a
programme, if the programme has a subtitle track of the lan-
guage that is designated for the 1st Subtitle Language, it will be
displayed. If the first language is not available but the second
language is available, the subtitle of the second language will
be displayed. If there is not any available language, no subtitle
will be displayed.
Apart from this setting, you can select a subtitle track with the
Audio language
Set the 1st Audio Language option and the 2nd Audio Lan-
guage option to your desired languages. When you watch a
programme, if the programme has an audio track of the lan-
guage that is designated for the 1st Audio Language, it will
be output. If the first language is not available but the second
language is available, the audio of the second language will be
output.
Apart from this setting, you can select an audio track with the
Download from Www.Somanuals.com. All Manuals Search And Download.
18 Preference Settings
3.2 Video and audio settings
You have to configure the video
and audio settings appropriately
to your television set and other
appliances.
Select the System Setting
>
A/V Output Setting menu. You
should see a screen like the left
figure.
3.2.1 Colour model
Through the TV SCART connector, the digital receiver is able
to output video in various colour models. If you have the
digital receiver linked to your television via this connector, you
should set the SCART Output option to your desired colour
model. If you have connected via the RCA connector labeled
VIDEO on the back panel, you do not have to set this option
because the digital receiver outputs CVBS video through the
RCA connector independent of the SCART connector.
It is known in general that the RGB colour model provides the
best video quality with little difference from the YUV colour
model but the CVBS colour model does the least. So RGB
would be most desirable for this option.
3.2.2 Video cassette recorder
You can have the digital receiver linked to your video cassette
recorder or such an appliance via the VCR SCART connector. In
that case, the digital receiver will operate differently depending
on the setting of the VCR Scart Type option. If the option is
set to Standard, the digital receiver will pass the video from
the video cassette recorder to your television when it starts
Download from Www.Somanuals.com. All Manuals Search And Download.
3.2 Video and audio settings 19
playback. But if the option is set to External A/V, the digital
receiver will not pass the video automatically. To pass it, you
£
have to press the AUX button.
¢
¡
3.2.3 Television aspect ratio
If you have a wide-screen television, set the TV Aspect Ratio
option to 16:9.
You can enjoy well both wide-screen programmes and normal-
screen programmes with your wide-screen television as the
above figures show. To watch normal-screen programmes in
full screen like the left figure, set the 4:3 Display Format option
to Full. Normal-screen pictures then will be inflated to fit to
the width of the wide screen. Otherwise, to watch them in the
original ratio like the right figure, set it to Center.
Otherwise, if you have a normal-screen television, set the TV
Aspect Ratio option to 4:3.
You cannot fully enjoy wide-screen programmes with your
normal-screen television as the above figures show. The left
figure shows a normal picture displayed in the normal screen.
To watch wide-screen programmes in the shape like the centre
Download from Www.Somanuals.com. All Manuals Search And Download.
20 Preference Settings
figure, set the 16:9 Display Format option to Letter Box. Wide-
screen pictures then will be reduced to fit to the width of the
normal screen. Otherwise, to watch them in the shape like the
right figure, set it to Center extract. Wide-screen pictures then
will be cut out on the left and right sides equally to fit to the
width of the normal screen.
3.2.4 High definition television
The digital receiver supports various video resolutions from
576 to 1080. In general a resolution of 720 or more is considered
high definition. The higher the resolution is, the better quality
you can enjoy. However, if your television set does not sup-
port high definition, you cannot enjoy high definition quality
picture.
Set the Video Format option as you desire. If you set this
option to 576P, the digital receiver will present even high
definition programmes in resolution of 576. On the contrary,
if you set it to 1080I, the digital receiver will present even
standard definition programmes in resolution of 1080. It is
recommended to set it to Auto if you have a high definition
television. With that setting the digital receiver will present a
programme as it is without any resolution conversion. While
watching television you can change the resolution with the
£
V.Format button. Whenever you press it, the video resolution is
changed in turn.
¢
¡
If you have the digital receiver linked to your television
via the component video connectors (Y, Pb and Pr) or
the HDMI connector, you have to toggle the video output
selection switch on the back panel to the YPbPr position.
Otherwise if you have connected it to your television via
the TV SCART connector, you have to toggle the switch
to the SCART position. The available values of the Video
Format option vary depending on which position you
toggle the switch to.
ART
SC
YPbPr
Download from Www.Somanuals.com. All Manuals Search And Download.
3.3 Local time setting 21
NOTE
You can enjoy only standard definition video with the following
connectors:
• Composite video connector (VIDEO)
• SCART connector (TV)
3.2.5 Audio mode
Basically, there are two audio sources as you can find two audio
sockets on the back panel of the digital receiver. You can enjoy
only one source or both of them in either stereo or mono. Set
the Sound Mode option as you desire.
Apart from this setting, you can change the sound mode with
the
The digital receiver can output two types of digital audio sig-
nals via the S/PDIF connector. One is an encoded signal, and
the other is a decoded signal. If your digital audio system does
not have a Dolby Digital decoder, you have to set the Dolby
Digital option to PCM. Otherwise, set it to Bitstream.
3.3 Local time setting
You should set your local time for timer events. If you do not
set the local time right, the programme time table provided by
the programme guide may be distrustful. For the programme
Download from Www.Somanuals.com. All Manuals Search And Download.
22 Preference Settings
Select the System Setting
>
Time
Setting menu. You should see a
screen like the left figure.
You can set the clock manually
or use the time signal, Green-
wich Mean Time (GMT), carried
as part of the digital television
broadcast.
To use Greenwich Mean Time,
take the following steps:
1. Set the Mode option to Auto; then the Time Offset option
becomes enabled.
2. Set the Time Offset option to the time difference between
3. To get Greenwich mean time, set the GMT Collection
option to one among the following:
Normal from all transponders
CAS TP from transponders of pay services
User Select from transponders specified by you
If you set it to User Select, then the Satellite option and
the Transponder option become enabled. Select your de-
sired satellite and transponders at those options. With
the above settings, the digital receiver will scan all trans-
ponders specified one by one until to get the Greenwich
Mean Time.
4. Make sure that your local time is correctly displayed on
the Local Time option.
To set the local time yourself, set the Mode option to Manual and
enter your local time to the Local Time option with the numeric
buttons. The time format is day/month/year 24-hour:minute.
Download from Www.Somanuals.com. All Manuals Search And Download.
3.3 Local time setting 23
Table 3.1: Time offset table
Time offset City
GMT − 12:00 Eniwetok, Kwajalein
GMT − 11:00 Midway Island, Samoa
GMT − 10:00 Hawaii
GMT − 09:00 Alaska
GMT − 08:00 Pacific Time US, Canada
GMT − 07:00 Mountain Time US, Canada
GMT − 06:00 Central Time US, Canada, Mexico City
GMT − 05:00 Eastern Time US, Canada, Bogota, Lima
GMT − 04:00 Atlantic Time Canada, La Paz
GMT − 03:30 Newfoundland
GMT − 03:00 Brazil, Georgetown, Buenos Aries
GMT − 02:00 Mid-Atlantic
GMT − 01:00 Azores, Cape Verde Islands
GMT
London, Lisbon, Casablanca
Paris, Brussels, Copenhagen, Madrid
South Africa, Kaliningrad
Baghdad, Riyadh, Moscow, St. Petersburg
Tehran
Abu Dhabi, Muscat, Baku, Tbilisi
Kabul
Ekaterinburg, Islamabad, Karachi, Tashkent
Bombay, Calcutta, Madras, New Delhi
Almaty, Dhaka, Colombo
GMT + 1:00
GMT + 2:00
GMT + 3:00
GMT + 3:30
GMT + 4:00
GMT + 4:30
GMT + 5:00
GMT + 5:30
GMT + 6:00
GMT + 7:00
GMT + 8:00
GMT + 9:00
GMT + 9:30
Bangkok, Hanoi, Jakarta
Beijing, Perth, Singapore, Hong Kong
Tokyo, Seoul, Osaka, Sapporo, Yakutsk
Adelaide, Darwin
GMT + 10:00 Eastern Australia, Guam, Vladivostok
GMT + 11:00 Magadan, Solomon Islands, New Caledonia
GMT + 12:00 Fiji, Auckland, Wellington, Kamchatka
If daylight saving time is observed in your state at the moment,
set the Daylight Saving Time option to On.
NOTE
Daylight saving time adds one hour to the time when the op-
tion is set to On. When setting the time offset from Greenwich
Mean Time, make sure that time offset does not include day-
light saving time.
Download from Www.Somanuals.com. All Manuals Search And Download.
24 Preference Settings
3.4 Parental control
In general, television programmes are classified according to
the level of violence, nudity and language of their content.
When you are watching a programme, you can check its pro-
gramme classification on the information box. For the informa-
You can prevent your children from watching specific pro-
grammes by specifying a programme classification.
Select the System Setting
>
Parental Control menu. You
should see a screen like the
left figure, and you will be
asked your Personal Identifica-
tion Number (PIN). The number
is initially set to ‘0000’.
If you wish to block 15 or above rated programmes, set the
Censorship option to 15 (age). Setting it to No block blocks no
programme; on the other hand, setting it to Total block blocks
every programme.
NOTE
If a programme does not have any programme classification
information, your censorship setting will not take effect.
If anyone is trying to watch a programme that is of or above
the censorship setting, the person has to enter the personal
identification number to override.
To change the number, select the Change PIN Code menu; then
an input box appears. You have to enter a desired number
twice for confirmation.
Download from Www.Somanuals.com. All Manuals Search And Download.
3.5 Adjusting the on-screen display 25
You can also restrict uses of some menus. Selecting the Access
Control menu displays a list of menus that you can lock. If the
Time Setting item is set to Locked, you have to enter the per-
sonal identification number when accessing the Time Setting
menu. If you enter a wrong number, you cannot use the menu.
To release a shut item, set it to Unlocked.
3.5 Adjusting the on-screen display
You can adjust the transparency level of the on-screen display.
Select the System Setting menu and set the OSD Transparency
option as you desire. Its available range is from 0 to 50 percent.
You can adjust the display time of the information box. For
the information box, see
§
select the System Setting menu and set the Info Box Display
Time option as you desire. Its available range is from 1 to 30
seconds. If you set this option to No Info Box, the information
box will not be displayed when you switch services. However,
pressing the
button will display the information box. If you
set this option to Never Hide, the information box will always
be displayed.
In addition, you can raise or lower the position of the informa-
tion box. Select the System Setting menu and set the Info Box
Position option as you desire. Its available range is from −10
to
+3 lines. The more high you set the option, the more low
the information box will be positioned.
Download from Www.Somanuals.com. All Manuals Search And Download.
26 Service Search
Chapter 4
Service Search
After connecting up the digital receiver, you will need to per-
form a service search.
4.1 Searching broadcasting services
This digital receiver can be operated with both fixed antenna
and motorized antenna. You have to configure antenna settings
according to your antenna system in the following order:
2. Set the position of your desired satellites if you have
a motorized antenna. You can control the antenna in
DiSEqC 1.2 mode or USALS mode. Refer DiSEqC 1.2 to
3. Perform service search.
4.1.1 Configuring LNB settings
There are in large two frequency bands for satellite broadcasts.
One is band which ranges approximately from 4 to 6 GHz.
C
Download from Www.Somanuals.com. All Manuals Search And Download.
4.1 Searching broadcasting services 27
The other is Ku band which ranges approximately from 12 to
18 GHz.
The LNB (Low Noise Block converter)
is used to take a wide band of relatively
high frequencies, amplify and convert
them to similar signals that is carried
at a much lower frequency, which is
called Intermediate Frequency (IF).
High frequencies from satellites are
converted into 950 to 2150 MHz by a
LNB.
Select the Installation
ting menu to configure the LNB
settings. You should see a
screen like the left figure.
>
LNB Set-
£
Pressing the OK button on the Satellite Name option displays
¢
¡
the satellite list in alphabetic order. Select the satellite toward
which your antenna is set to face. Even if you cannot find
your desired satellite, you can add your desired satellite to the
The digital receiver has a database about broadcasting satellites
and their transponders, containing the following information:
satellite position, frequency range, symbol rate, polarization
and LNB frequency corresponding to the frequency range. So
you might not have to specify the LNB Frequency option. How-
Download from Www.Somanuals.com. All Manuals Search And Download.
28 Service Search
ever, if you have selected the Other entry at the Satellite Name
option to specify a satellite that is not in the satellite list, you
might have to fill in the correct LNB frequency. The absolute
difference between a broadcasting frequency and its LNB fre-
quency must be within 950 to 2150 MHz. For example, if the
frequency band of your desired satellite ranges from 3660 to
4118 MHz, you have to set the LNB Frequency option to 5150
MHz.
The LNB has to be supplied with electric power to operate. Set
the LNB Power option to On if it does not have any other power
supply.
You had better ignore the 22 kHz option.
The digital receiver is designed to be compatible with DiSEqC
(Digital Satellite Equipment Control) switches. It is possible
to connect several antennas to one digital receiver by DiSEqC
switches. A DiSEqC 1.0 switch allows switching between up to
four satellite sources and a DiSEqc 1.1 switch allows switching
between up to 16 satellite sources.
Set the DiSEqC 1.0 option and the DiSEqC 1.1 option accord-
ing to your antenna configuration.
For example, to select the antenna con-
nected to the A5 input in the left figure,
set the DiSEqC 1.1 option to 2 of 4 and
the DiSEqC 1.0 option to 1 of 4. If you
have a mini DiSEqC 1.0 switch which
has only two inputs, you should set the
DiSEqC 1.0 option to Mini A instead of
1 of 4.
Download from Www.Somanuals.com. All Manuals Search And Download.
4.1 Searching broadcasting services 29
4.1.2 Configuring DiSEqC 1.2 settings
Your motorized antenna will turn toward your desired satellites
horizontally by DiSEqC 1.2.
When you switch to an service, if the service is
provided by a satellite other than current one,
it will take longer time than usual because the
antenna has to turn to its position.
To use the DiSEqC 1.2 protocol,
select the Installation
>
Motor-
ized DiSEqC 1.2 menu. You
should see a screen like the left
figure.
At first you have to set the Mo-
torized DiSEqC 1.2 option to En-
able.
To get the correct position of your desired satellite, perform the
following steps:
1. Choose your desired satellite at the Satellite Name op-
tion.
2. Set the DiSEqC Command Mode option to User.
3. Set the Motor Control option to Goto. Then the antenna
will turn toward your selected satellite by the position
data that the digital receiver has.
4. If the receiving quality, which is displayed at the bottom
right of the screen, is not good, tune the antenna finely
with the Movement option. If you set it to 2(E), the an-
tenna will move to the east by two degrees. At this time
Download from Www.Somanuals.com. All Manuals Search And Download.
30 Service Search
you had better check the receiving quality of every trans-
ponder and choose the best one at the Transponder (or
Frequency) option. It will be helpful to your fine tuning.
5. Finally set the Motor Control option to Store to save the
tuned position when the receiving quality is best.
There are more motor control options for installers, but this
guide does not describe them. If you are an installer, refer them
to the manual about the STAB rotor.
4.1.3 Configuring USALS settings
USALS (Universal Satellite Automatic Location System), also
known as DiSEqC 1.3, calculates the positions of all available
satellites from your location. Compared to DiSEqC 1.2, it is no
longer required to manually search and store every satellite
position. Just pointing to a known satellite position is enough.
This position will act as a central point. The USALS will then
calculate positions of visible satellites.
To use the USALS protocol, se-
lect the Installation
>
USALS
Setting menu. You should see
a screen like the left figure.
At first you have to set the Mo-
torized DiSEqC 1.3 option to En-
able.
To get every satellite position calculated, perform the following
steps:
1. Choose your desired satellite at the Satellite Name op-
tion.
Download from Www.Somanuals.com. All Manuals Search And Download.
4.1 Searching broadcasting services 31
2. Enter your location to the My Longitude option and the
£
£
My Latitude option with the V−
tons.
,
V+ and numeric but-
¢
¡ ¢
¡
3. Enter the position of your selected satellite to the Satellite
Angle option if it is not correct.
4. Select the Goto the position option; then the antenna
will turn toward your selected satellite as calculating its
position.
5. If the receiving quality, which is displayed at the bottom
right of the screen, is not good, then tune the antenna
finely with the Move option. The changed position is
automatically saved. At this time you had better check
the receiving quality of every transponder and choose
the best one at the Transponder (or Frequency) option. It
will be helpful to your fine tuning.
4.1.4 Searching services
To perform service search, select
the Installation Service Search
>
menu. You should see a screen
like the left figure.
There are four service search methods:
• Searching every service of a satellite.
• Searching every service of a transponder.
• Searching one service of a transponder.
Download from Www.Somanuals.com. All Manuals Search And Download.
32 Service Search
•
Searching every service of a SMATV (Satellite Master
Antenna Television) system.
Searching every service of a satellite
To search every service of a satellite, perform the following
steps:
1. Choose your desired satellite at the Satellite Name op-
tion.
2. Set the Search Mode option to Auto.
3. If you set the Network Search option to On, the digital
receiver will check up the up-to-date channel information
as searching services, but it takes rather longer time.
Searching every service of a transponder
To search every service of a transponder, perform the following
steps:
1. Choose your desired satellite at the Satellite Name op-
tion.
2. Set the Search Mode option to Manual.
3. Choose your desired transponder at the Frequency op-
tion or enter it with the numeric buttons.
4. Enter the symbol rate of your desired transponder to the
Symbol Rate option with the numeric buttons.
5. Set the Polarization option to the polarization of your
desired transponder.
6. If you set the Network Search option to On, the digital
receiver will check up the up-to-date channel information
as searching services, but it takes rather longer time.
7. Set the Modulation option to the modulation type of your
desired transponder. If your desired transponder has
high definition broadcasts, you should set this option to
DVB-S2 QPSK or DVB-S2 8PSK. Then the FEC option
Download from Www.Somanuals.com. All Manuals Search And Download.
4.1 Searching broadcasting services 33
and the Pilot option will become enabled. You also should
set these options correctly.
NOTE
You may get transponder information from a satellite magazine
Searching one service of a transponder
To search one service of a transponder, perform the following
steps:
1. Choose your desired satellite at the Satellite Name op-
tion.
2. Set the Search Mode option to Advanced.
3. Choose your desired transponder at the Frequency op-
tion or enter it with the numeric buttons.
4. Enter the symbol rate of your desired transponder to the
Symbol Rate option with the numeric buttons.
5. Set the Polarization option to the polarization of your
desired transponder.
6. Specify the packet identifiers of your desired service at
the PID option with the numeric buttons. A packet iden-
tifier is used to verify audio and video streams.
Searching every service of SMATV system
To search every service of a SMATV system, if the digital re-
ceiver is connected to it, perform the following steps:
1. Choose your desired satellite at the Satellite Name op-
tion.
2. Set the Search Mode option to SMATV.
3. Choose your desired transponder at the Frequency op-
tion or enter it with the numeric buttons.
Download from Www.Somanuals.com. All Manuals Search And Download.
34 Service Search
4. Enter the symbol rate of your desired transponder to the
Symbol Rate option with the numeric buttons.
5. Set the Polarization option to the polarization of your
desired transponder.
You can search pay services as well as free services as follows:
•
To search only free services, set the FTA/Scrambled option
to FTA only.
• To search only pay services, set it to CAS only.
•
To search both free services and pay services, set it to FTA
+ CAS.
To start service search, select the Start Search item; then a list
box appears, in which found services will be listed. When it has
£
completed, press the OK button to save found services. To stop
¢
¡
£
at any time or to exit without saving, press the EXIT button.
¢
¡
4.2 Editing the transponder list
You can add, delete or modify
satellite or transponder informa-
tion.
Select the Installation
>
SAT/TP
Edit menu. You should see a
screen like the left figure.
To add a satellite entry, select the Add Satellite option; then
the on-screen keyboard appears. Enter your desired name and
Download from Www.Somanuals.com. All Manuals Search And Download.
4.3 Resetting to factory settings 35
To change a satellite entry’s name, select your desired entry at
the Satellite Name option and select the SAT Name Edit option.
Then the on-screen keyboard appears. Change the name as you
desire and save it.
To delete a satellite entry, select your desired entry at the Satel-
lite Name option and select the Delete Satellite option; then
you get asked for confirmation. If you select Yes, it will be
deleted.
To add a transponder entry, select your desired entry at the
Satellite Name option and select the Add new TP option. Then
the transponder information box appears. Enter a frequency
and its symbol rate with the numeric buttons, and specify its
polarization.
To delete a transponder entry, select your desired entry at the
Frequency option and select the Delete TP option; then you
get asked for confirmation. If you select Yes, it will be deleted.
4.3 Resetting to factory settings
The digital receiver maintains the following data:
• Satellite list
• Services list
• Favourite list
• Timer list
• Preference settings
You can reset all data of the digital receiver. To do that, select
the Installation
>
Factory Setting menu, and then you are asked
for confirmation. If you select Yes, service entries, favourite
entries and timer events will all be deleted, and preference
options will be reset to the manufacturer’s factory settings.
4.4 Resetting to installer settings
You can store your own data including the following:
Download from Www.Somanuals.com. All Manuals Search And Download.
36 Service Search
• Satellite list
• Services list
• Favourite list
• Preference settings
Also you can restore them at any time.
To store your data, select the Installation
>
System Recovery
menu and select the Store option; then you get asked for the
presonal identification number. The number may be different
from yours because this function is usually permitted only to
installers. If you have entered a right number, you get asked
for confirmation. If you select Yes, your data will be stored.
Whenever you store your data, they are all overwritten.
To restore your data, select the Installation
>
System Recovery
menu and select the Recover option; then you get asked for
confirmation. If you select Yes, your data will be restored.
Download from Www.Somanuals.com. All Manuals Search And Download.
37
Chapter 5
Daily Usage
5.1 Volume control
£
£
Use the V− and V+ buttons to alter the volume to a com-
fortable level. You may need to adjust the volume on your
television set too. To temporarily switch off the sound, press
the
¢
¡
¢
¡
button. Press it again to restore the sound to previous
level.
5.2 Watching television
£
£
To change services, press the P+ or P− button. Pressing the
¢
¡
¢
¡
button switches to the previously viewed service. In ad-
dition, you can switch to your desired service by entering its
service number with the numeric buttons. You can also select a
service to watch in the services list.
5.2.1 The services list
£
To view the services list, press the OK button.
¢
¡
Download from Www.Somanuals.com. All Manuals Search And Download.
38 Daily Usage
On the services list, you can see
the service information:
• Service number and name
• Transmitting satellite
• Transponder information
A dollar sign ($) may be marked on some entries, indicating
pay service. To watch pay services, you need the subscription
card.
To select a desired service, put the highlight bar on its entry
£
£
£
with the P+ or P− button and press the OK button; then it will
¢
¡
¢
¡
¢
¡
be presented.
£
£
Pressing the V− or V+ button skips over 10 entries up or down.
¢
¡ ¢
¡
Entering a service number with the numeric buttons puts the
highlight bar on its entry.
You can switch between the television services list and the
radio services list by pressing the
button.
£
Pressing the F3 button performs an alphabetic browse. For
¢
¡
instance, when the highlight bar is on an entry of which initial
£
is B, pressing the F3 button puts the highlight bar on the first
¢
¡
entry of which initial is C.
£
To sort the services list by service name, press the F2 but-
ton. Pressing this button once more makes it sorted by service
¢
¡
number.
£
Pressing the F4 button displays the additional options, with
which you can do the following:
¢
¡
•
Select your desired satellite at the Satellite option, then
only services provided by the selected satellite will be
listed.
Download from Www.Somanuals.com. All Manuals Search And Download.
5.2 Watching television 39
•
•
By setting the Show Provider option to On, you can view
service entries by groups of broadcasters.
To change the name of the highlighted service, select the
Rename option; then the on-screen keyboard appears,
with which you can enter a new name. See
to use the on-screen keyboard.
§
6.3 for how
•
•
You can prevent other family members from watching the
highlighted service by setting the Lock option to Locked.
You have to enter your personal identification number to
watch or unlock it.
To delete the highlighted service, select the Delete option;
then you are asked for confirmation. If you select Yes, it
will be deleted. If you want to restore it as before, you
have to perform service search again. See
search.
§
4.1 for service
•
•
To add the highlighted service into a favourite group,
select the Add to Fav option; then the favourite groups
will be displayed. Put the highlight bar on a desired
£
group and press the OK button.
¢
¡
You can additionally sort the services list with the Sorting
option as follows:
Default by service number
Alphabetic by service name
Satellite by satellite
FTA–CAS from free services to pay services
CAS–FTA from pay services to free services
Provider by broadcaster
Fav–NoFav from favourite services to unfavourite ser-
vices.
£
Pressing the SAT button displays the satellite list. Once you
select a desired satellite, only services provided by the selected
satellite are listed.
¢
¡
Download from Www.Somanuals.com. All Manuals Search And Download.
40 Daily Usage
5.2.2 The favourite services list
You can select a service to watch on a favourite list as well as
on the services list.
To display the favourite lists,
£
press the FAV button.
You
¢
¡
should see a screen like the left
figure. As you move the high-
light bar up or down on the
favourite group list at the left
box, favourite services belong-
ing to the highlighted group are
listed on the right box.
To select a favourite service, put the hightlight bar on a desired
£
group and press the V+ button; a highlight bar appears on its
¢
¡
favourite services list. Once you select a desired service with
£
the OK button, it will be presented. Otherwise, to select other
¢
¡
£
group, press the V− button.
¢
¡
After you have selected a favourite service, if you then switch
£
£
to another service using the P+ or P− button, it will be also
¢
¡
¢
¡
another favourite service of the selected group. The digital
receiver will remind you what group you have selected by
displaying its name at the top right of the screen whenever you
switch services. If you wish to get out of the current group,
select the All services group on the favourite group list.
Besides that, you can add or delete a favourite group or service.
To add a service you are watching currently into a favourite
group, put the highlight bar on a desired group and press the
£
£
F3 button. To create a new group, press the F2 button; then
the on-screen keyboard appears. Enter your desired name and
¢
¡
¢
¡
save it. See
§
Download from Www.Somanuals.com. All Manuals Search And Download.
5.2 Watching television 41
£
delete a group or a service, press the F4 button; then you get
asked for confirmation. If you select Yes, it will be deleted.
¢
¡
5.2.3 Viewing programme information
Pressing the
you can see all of the following:
• Service number and name
button displays the information box, on which
• Transmitting satellite
• Transponder information
• Signal level and quality
• Programme name
• Programme classification symbol
• Programme summary
• Broadcasting time
• Current time
In addition, you might see the following symbols:
•
•
Subtitle symbol ( ) if subtitle tracks are provided on the
current programme.
Teletext symbol ( ) if teletext pages are provided on the
current service.
• Lock symbol ( ) if the current service is locked.
• Dollar symbol ($) if the current service is a pay service.
•
Multifeed symbol ( ) if the current programme is pro-
vided as a multifeed programme. To use this feature,
If the electronic programme guide is provided on the current
service, you can see the information about the current and next
£
£
programmes with the V− or V+ button. To adjust the sound
¢
¡
¢
¡
£
£
volume in this case, hold down the V− or V+ button until the
¢
¡
¢
¡
sound bar appears and reaches your desired level.
Download from Www.Somanuals.com. All Manuals Search And Download.
42 Daily Usage
Pressing the
button once more displays detailed information
about the current programme. To hide the information box,
£
press the EXIT button.
¢
¡
5.2.4 Selecting audio tracks
Some programmes are provided with audio tacks in one or
more languages. Pressing the button displays available au-
dio tracks. Once you select an audio track, it will be sounded.
In addition, you can enjoy audio tracks in four sound modes:
Stereo, Mono, Left or Right. However, if a multifeed pro-
gramme is provided at the moment, video tracks will be dis-
played. In this case, you have to press the
to select an audio track.
button once more
5.2.5 Selecting subtitle tracks
Some programmes are provided with subtitle tracks in one or
more languages. If the current programme provides subtitle
tracks, the subtitle symbol ( ) will be marked on the infor-
mation box. Pressing the
button displays available subtitle
tracks. Once you select a subtitle track, it will be displayed.
5.2.6 Viewing teletext
On some services, such information as weather reports, news
or stock quotations is provided by means of teletext. If the
current service provides teletext, the teletext symbol ( ) will
be displayed on the information box. Press the
view teletext pages.
button to
Select a desired page to view by entering its page number with
the numeric buttons. You can zoom into a teletext page with
£
£
the F3 button, and adjust its transparency level with the F4
¢
¡
¢
¡
£
button. To hide the teletext screen, press the EXIT button.
¢
¡
Download from Www.Somanuals.com. All Manuals Search And Download.
5.3 Viewing electronic programme guide 43
5.3 Viewing electronic programme guide
The Electronic Programme Guide shows the current and sched-
uled programmes that are or will be available on each service
with a short summary for each programme.
£
Pressing the GUIDE button dis-
¢
¡
plays the electronic programme
guide, on which you can see the
following:
• Scheduled programmes
• programme summary
• Broadcasting date
• Broadcasting time
To see detailed information of a desired programme, put the
£
£
highlight bar on your choice with the P+ or P− button and
¢
¡
¢
¡
£
press the
button. To switch to another service, press the V−
¢
£
¡
£
or V+ button. You can travel over previous days with the F2
¢
¡
¢
¡
£
button, and can travel over next days with the F3 button.
¢
¡
To see the programme guide for radio broadcasts, press the
button. To switch it back, press the
button again.
£
Pressing the F1 button displays the programme guide in the
form of a spreadsheet. To switch it back, press the F1 button
¢
¡
£
¢
¡
again.
You can make a timer event on the electronic programme guide
as follows:
1. Select a service you want.
£
2. Press the GUIDE button to display its programme guide.
¢
¡
£
3. Select a programme you want with the OK button, then
¢
¡
P
is marked up on the entry. At the same time, a timer
event with the selected programme will be made in the
Download from Www.Somanuals.com. All Manuals Search And Download.
44 Daily Usage
£
4. To remove the marking, press the OK button once again.
¢
¡
5.4 Watching multifeed programme
Some broadcasts such as sports channels can provide a variety
of perspectives on a programme at a same time. We call it a
multifeed programme. You can select and watch a perspective
you prefer.
If a multifeed programme is provided on the current service,
the multifeed symbol ( ) will be marked on the information
box. Press the
button, then available video tracks will be
listed. Once you select one, it will be presented. At this time,
you have to press the
tracks.
button once more to select audio
5.5 Making timer events
You can make the digital receiver to present your desired ser-
vice at a specific time. Even if the digital receiver is off, it will
turn on at the specified time.
To input a timer recording, select
the Timer Setting menu; then the
timer list will be displayed.
To add a new timer event, press
£
the F1 button, and a box like
the left figure appears. Take the
following steps:
¢
¡
1. If you want a radio programme, set the Type option to
Radio; otherwise, set it to TV.
Download from Www.Somanuals.com. All Manuals Search And Download.
5.5 Making timer events 45
2. Set the Satellite option to the satellite which transmits the
£
service you want. Pressing the OK button on this option
displays a satellite list, from which you can select your
desired satellite.
¢
¡
3. Set the Wakeup Service option to the service which pro-
£
vides the programme you want. Pressing the OK button
on this option displays a services list, from which you
can select your desired service.
¢
¡
4. There are five timer modes:
One Time means literally ‘one time’.
Every Day means literally ‘every day’.
Every Weekend means ‘Saturday and Sunday every
week’.
Weekly means ‘one day every week’.
Every Weekday means ‘from Monday to Friday every
week’.
If your favourite programme is broadcasted at weekends
and you wish to watch every episode of the programme,
set the Mode option to Every Weekend.
5. Set the Wakeup Day option to a desired date, on which
the digital receiver will turn on. The date format is
day/month/year-day of the week.
Set the Wakeup Time option to a desired time, at which
the digital receiver will turn on. The time format is
hour:minute.
6. Set the Duration option to a desired time, in which the
digital receiver will turn off.
7. To set a timer event with the above settings, select the OK
option; otherwise, it will not be saved and will not occur.
To delete a timer event, put the highlight bar on the entry you
£
want to remove and press the F2 button; then you are asked
for confirmation. If you select Yes, it will be deleted.
¢
¡
Download from Www.Somanuals.com. All Manuals Search And Download.
46 Listing Services
Chapter 6
Listing Services
6.1 Editing the services list
You would have got the services list after service search. You
can rename, move, lock or delete service entries on the services
list.
Select the Organizing Svc/Fav >
Organizing Services menu. You
should see a screen like the left
figure.
There are editing options on the
left column and service entries
on the right column.
Once you put the highlight bar on a desired option on the
£
left column and press the OK button, you can select a desired
¢
¡
service to edit on the right column. To go over to the other
£
column, press the F1 button.
¢
¡
Download from Www.Somanuals.com. All Manuals Search And Download.
6.1 Editing the services list 47
To edit the radio services list, press the
button; then radio
service entries will be listed on the right column. To switch
back to the television services list, press it again.
To change the name of a service, select the Rename and select a
desired service; then the on-screen keyboard appears. See
for how to use the on-screen keyboard.
§
Unlike analogue broadcasts, each service does not have a
proper service number in digital broadcasts. Service num-
bers are just assigned to services in the order that they were
found in service search. So you can reassign a service num-
ber by moving a service entry. To move a service entry, select
the Move option and select a desired service; then the selected
service becomes darker. As you move it up or down, it gets
£
renumbered according to the position. Press the OK button to
fix it.
¢
¡
You can lock some services to prevent your children from
watching them. To lock a service, select the Lock option and
select a desired service; then the selected service gets marked
with a lock symbol ( ) on it. If anyone tries to watch a locked
service, the person has to enter the personal identification num-
ber that is set to the Change PIN Code option. See
§
3.4 for this
£
option. Pressing the OK button on a locked service entry turns
¢
¡
¡
it back to be unlocked.
To delete a service, select the Delete option and select a desired
£
£
service with the OK button, and then press the EXIT button;
¢
¢
¡
you get asked for confirmation. If you select Yes, the selected
service will be deleted. If you want to undo the deleted service,
there is nothing you can do but perform a service search again.
Once you select the Sort option on the left column, sorting
options are displayed as follows:
Default by service number
Alphabetic by service name
Satellite by satellite
FTA–CAS from free services to pay services
Download from Www.Somanuals.com. All Manuals Search And Download.
48 Listing Services
CAS–FTA from pay services to free services
Provider by broadcaster
Fav–NoFav from favourite services to unfavourite services.
Transponder by transponder
6.2 Editing the favourite list
You can make your own favourite services list. In fact, you can
define multiple favourite services lists, each being a ‘group’ of
chosen services.
Select the Organizing Svc/Fav >
Organizing Favorites menu. You
should see a screen like the left
figure.
There are three columns:
• Group list (left)
• Favourite list (centre)
• Services list (right)
The services list contains all available services, whereas the
favourite list contains only chosen services that have been
added to the highlighted group. As you move the highlight
bar up or down on the group list, favourite services belonging
to the highlighted group get shown in the favourite list.
You can add up to 30 groups. To add a group, select the NEW
option in the group list; then the on-screen keyboard appears.
To rename a group, put the highlight bar on the group entry you
£
want and press the F2 button; then the on-screen keyboard
¢
¡
Download from Www.Somanuals.com. All Manuals Search And Download.
6.2 Editing the favourite list 49
To delete a group, put the highlight bar on the group entry you
£
want and press the F3 button; then a message box appears
asking you for confirmation. If you select Yes, it will be deleted.
¢
¡
You can add a favourite service to a group by taking the follow-
ing steps:
1. Put the highlight bar on a desired group entry in the
£
group list and press the OK button to select it. The high-
light bar then moves to the services list.
¢
¡
2. To add a service to the selected group, put the highlight
£
bar on a desired service entry and press the OK button.
The selected service entry gets added to the favourite list.
Repeat this step to add more entries.
¢
¡
£
3. Press the F1 button and the highlight bar get moved to
¢
¡
the favourite list. You can delete a favourite entry with
£
the OK button.
¢
¡
£
4. To select another group, press the F1 button again. By
¢
¡
£
pressing the F1 button, the highlight bar gets moved to
¢
¡
each column.
To add radio services, press the
button; then radio service
entries get listed in the services list. To recall the television
services list after adding radio services, press the
again.
button
With your favourite services list, you can select your favourite
Download from Www.Somanuals.com. All Manuals Search And Download.
50 Listing Services
6.3 How to use on-screen keyboard
You can move the highlight key
£
horizontally with the V− and
¢
¡
£
V+ buttons and vertically with
¢
¡
£
£
the P+ and P− buttons. Press-
¢
¡
¢
¡
£
ing the OK button on a key en-
¢
¡
ters its letter in the input line. To
type a space, select the Space
key. To type lower case letters or
numerals, select the Other key.
To delete a letter, put the cursor to the right of the desired letter
on the input line and then select the Del key. You must select
the Save key to complete naming; otherwise, if you press the
£
EXIT button, it will not be named.
¢
¡
6.4 Transferring receiver data
The digital receiver retains the following data:
• Satellite and transponder data
• Services list
• Favourite lists
• Preference settings
It is possible to transfer the receiver data from the digital re-
ceiver to another same digital receiver by connecting them with
a RS-232 cable. To have the receiver data transferred, perform
the following steps:
Download from Www.Somanuals.com. All Manuals Search And Download.
6.4 Transferring receiver data 51
1. Plug one end of a RS-232 cable (9 pin D-
sub cable) into the RS-232 port on the dig-
ital receiver, and the other end into the
matching port on the other digital receiver.
2. Turn on the source digital receiver.
3. Select the Installation
>
Transfer Firmware
>
Transfer Data to Other IRD menu, then
you get asked for confirmation; select Yes.
4. To start the data transfer, turn on the target
digital receiver.
5. A progress bar appears showing the
progress of the data transfer.
6. Restart the target digital receiver when the
data transfer is complete.
Download from Www.Somanuals.com. All Manuals Search And Download.
52 Firmware Update
Chapter 7
Firmware Update
The digital receiver has a stable and convenient firmware to
use. However, a new firmware may be released to improve
the digital receiver. You can get the latest firmware and an
update utility which runs on most versions of Windows from
7.1 Checking the firmware information
You have to check the firmware
information of your digital re-
ceiver before downloading a
new firmware. Select the Infor-
mation
>
IRD Status menu. You
should see a screen like the left
figure.
Remember the System ID, and download a firmware with the
same system identification.
Download from Www.Somanuals.com. All Manuals Search And Download.
7.2 From a USB memory device 53
NOTE
You can only update with firmwares of which system identifi-
cation is identical to that of yours. Otherwise you will fail in
firmware update.
7.2 From a USB memory device
If you have a USB memory stick, you can update the firmware
from it by performing the following steps:
1. Download a new firmware from the Topfield website.
2. Copy the firmware file to your USB memory stick.
3. Insert the USB memory stick into the USB port on the
back panel of the digital receiver.
4. Select the Installation
>
USB Firmware Upgrade menu,
then the files in the USB memory are listed.
5. Place the highlight bar on the right firmware file and
£
press the OK button, then a countdown will be displayed
on the front display of the digital receiver.
¢
¡
6. When the ‘END’ message appears, restart the digital re-
ceiver.
NOTE
Your USB memory must be formatted in the FAT file system.
Otherwise, the digital receiver cannot recognize your USB
memory. In addition, the digital receiver can only recognize
files and directories which are named with only alphabetic, nu-
meric and underscore letters. If there is a file or forlder named
with other letters, the digital receiver cannot recognize not only
it but also its subsequent files and folders.
Download from Www.Somanuals.com. All Manuals Search And Download.
54 Firmware Update
7.3 From your computer via RS-232 port
It is possible to transfer a new firmware to the digital receiver
from your computer by connecting them with a RS-232 cable.
You need TFD-Down, a firmware transfer utility for this, which
To update the firmware with this method, perform the follow-
ing steps:
1. Download a new firmware applicable to
your digital receiver from the Topfield
website.
2. Turn off the digital receiver.
3. Plug one end of a RS-232 cable (9 pin D-
sub cable) into the RS-232 port on the dig-
ital receiver, and the other end into the
matching port on your computer.
4. Run TFD-Down.
The instructions on how to use TFD-Down are as follows:
1. Press the Find button to select the new
firmware file.
2. Press the download button, and then turn
on the digital receiver to start the file trans-
fer.
3. A countdown will be displayed on screen
4. Restart the digital receiver when the file
transfer is complete.
Download from Www.Somanuals.com. All Manuals Search And Download.
7.4 From another digital receiver via RS-232 port 55
7.4 From another digital receiver via RS-232 port
It is possible to transfer the firmware from the digital receiver
to another same digital receiver by connecting them with a RS-
232 cable. To update the firmware with this method, perform
the following steps:
1. Turn off the target digital receiver.
2. Plug one end of a RS-232 cable (9 pin D-
sub cable) into the RS-232 port on the dig-
ital receiver, and the other end into the
matching port on the other digital receiver.
3. Turn on the source digital receiver if not
already on.
4. Select the Installation
>
Transfer Firmware
>
Transfer Firmware to Other IRD menu,
then you get asked for confirmation; select
Yes.
5. Turn on the target digital receiver to start
the firmware transfer.
6. A progress bar appears showing the
progress of the firmware transfer.
7. Restart the target digital receiver when the
firmware transfer is complete.
Download from Www.Somanuals.com. All Manuals Search And Download.
56 Firmware Update
7.5 Over the air
You can get a new firmware over the air.
Select the Installation
>
OTA
Firmware Upgrade menu. You
should see a screen like the left
figure.
Selecting the Start command
starts firmware update.
On the left table is presented
the transponder information
appointed by the manufac-
turer, Topfield for firmware
update.
Satellite
Frequency
Symbol Rate 22000 KS/s
Polarisation
PID
Astra (19.2° E)
12603 MHz
Horizontal
347
This transponder information can be changed. You can get the
Download from Www.Somanuals.com. All Manuals Search And Download.
57
Index
Center extract, 20
Change PIN Code, 24
CI, 5
Common Interface, 5
Common Interface, 6
Daylight Saving Time, 23
Delete Satellite, 35
Delete TP, 35
DiSEqC, 28
DiSEqC 1.0, 28
DiSEqC 1.1, 28
DiSEqC Command Mode, 29
Dolby Digital, 21
download, 54
Duration, 45
AUDIO L, 13
DVB, 1
AUDIO L/R, 9
AUDIO R, 13
DVB-S2 8PSK, 32
DVB-S2 QPSK, 32
Auto, 32
Electronic Programme Guide, 43
Button, 4
Every Weekend, 45
CAM, 5
CAS only, 34
Censorship, 24
Center, 19
Factory Setting, 35
FEC, 32
Find, 54
Download from Www.Somanuals.com. All Manuals Search And Download.
58 INDEX
Movement, 29
multifeed, 44
Full, 19
My Latitude, 31
My Longitude, 31
Network Search, 32
NEW, 48
No block, 24
GMT Collection, 22
Goto, 29
Goto the position, 31
Normal, 22
normal-screen television, 19
HDMI, 9
high definition, 20
One Time, 45
Organizing Favorites, 48
Organizing Services, 46
OTA Firmware Upgrade, 56
Other, 28
Info Box Display Time, 25
Info Box Position, 25
information box, 41
IRD Status, 52
Parental Control, 24
PID, 33
keyboard, 50
Pilot, 33
PIN, 24
Language Setting, 16
Letter Box, 20
LNB, 27
LNB IN, 9
LNB IN, 11
Radio, 44
radio services list, 47
Recover, 36
RS-232, 10
LNB OUT, 11
LNB Power, 28
LNB Setting, 27
Local Time, 22
S/PIDF, 14
Manual, 32
Menu Language, 16
Mini A, 28
Modulation, 32
mono, 21
Motorized DiSEqC 1.2, 29
Motorized DiSEqC 1.3, 30
Satellite Angle, 31
SCART, 20
SCART Output, 18
Download from Www.Somanuals.com. All Manuals Search And Download.
59
Service Search, 31
services list, 37
Show Provider, 39
User Select, 22
VCR, 10
VCR, 14
Sort, 47
VIDEO, 9
Sorting, 39
Sound Mode, 21
Space, 50
Video Format, 20
Start, 56
Start Search, 34
stereo, 21
Wakeup Day, 45
Wakeup Service, 45
Wakeup Time, 45
wide-screen television, 19
subtitle, 42
System ID, 52
System Recovery, 36
System Setting, 25
Y/Pb/Pr, 9
YPbPr, 20
teletext, 42
television services list, 47
time format, 22
Time Offset, 22
timer list, 44
Timer Setting, 44
transponder, 1
TV Aspect Ratio, 19
USALS, 30
USALS Setting, 30
USB, 9
USB, 53
USB Firmware Upgrade, 53
User, 29
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Manufactured under license from Dolby Laboratories. Dolby and the
double-D symbol are trademarks of Dolby Laboratories.
Correct disposal of this product
This marking shown on the product or its literature indicates that it should
not be disposed with other household wastes at the end of its working life. To
prevent possible harm to the environment or human health from uncontrolled
waste disposal, please separate this from other types of wastes and recycle it
responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this
product or their local government office for details of where and how they
can dispose this product for environmentally safe recycling.
Business users should contact their supplier and check the terms and condi-
tions of the purchase contract. This product should not be mixed with other
commercial wastes for disposal.
Topfield continues to improve the digital receiver which this guide explains. So some expla-
nations and illustrations in this guide could be different from the actual digital receiver.
Copyright © 2007, Topfield Co., Ltd.
English version
110T-94232-201-0
Download from Www.Somanuals.com. All Manuals Search And Download.
|