TomTom ONE
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Before You Start...
Before You Start...
Switching on and off
To switch your TomTom ONE on or off, press and hold the On/Off button for
2 seconds. The first time you switch on, it may take a short while for your
device to start.
Note: In rare cases, your ONE may not start correctly. If this happens, press
the reset button, then switch on the device again.
Setting up
To set up your TomTom ONE you need to answer a few questions by tapping
the screen.
Important: Take care to select the correct language, since the language you
choose will be used for all menus and written instructions.
Battery notes
For information on connecting your computer, see Using TomTom HOME
Note: Your TomTom ONE uses a small amount of battery power to remember
the last screen being shown when the device is switched off.
If you do not charge your ONE for a prolonged period of time, the next time
you start your ONE it will show the default starting screen. All other device
settings will still be maintained.
Improving reception
If your TomTom ONE takes longer than 5 minutes to find your current
position, make sure that the device is in an open space away from tall objects
such as buildings or trees.
When you connect your TomTom ONE to your computer, you can use
TomTom HOME to download information about GPS satellite positions during
the next 7 days. This helps your ONE to find your position faster.
Important: Some vehicles have heat reflective shielding in the windscreen.
This may prevent your ONE from locating your current position.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Windshield Holder
Use the windshield holder to install your TomTom ONE inside your car.
To attach the holder, press the suction cup firmly to the windshield in your car,
in an area of the windshield where the glass is flat.
Make sure that both the holder and your windshield are clean and dry before
you attach the holder. Place the holder so that it does not interfere with your
view of the road.
Take care of your TomTom ONE
Never leave your TomTom ONE or accessories in view when you leave the car
or they may become an easy target for thieves.
You can set a password for your TomTom ONE which must be entered every
time you start your ONE. For more information, see Using TomTom HOME
It is important to take care of your ONE.
• Your ONE is not designed for use in extreme temperatures and any such
exposure may cause permanent damage.
• Do not open the casing of your ONE under any circumstances. Doing so
may be dangerous and will invalidate the warranty.
• Wipe or dry the screen of your ONE using a soft cloth. Do not use any liquid
cleaners.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Driving View
Driving View
When your TomTom ONE starts, you are shown the Driving View along with
detailed information about your current location.
Tap the center of the screen at any time to open the Main Menu.
Note: The Driving View is shown in black and white until your ONE locates
your current position.
ATap + and - to zoom in and out.
BYour current position.
CThe name of the next major road or road sign information, if applicable.
DNavigation instruction for the road ahead.
Tap this area to repeat the last spoken instruction and to change the
volume.
EThe name of the street you are on.
FInformation about your trip such as trip time, remaining distance and arrival
time.
To select what will be shown, tap Status bar preferences in the Preferences
menu.
GGPS signal strength.
HTraffic bar - requires an RDS-TMC Traffic Receiver (available as an
accessory).
To set up Traffic information, tap the Traffic bar to open the Traffic menu or
tap TomTom Traffic in the Main Menu.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Making your first trip
Making your first trip
Planning a route with your TomTom ONE is easy. To plan your first route,
follow the steps below.
Important: You should always plan your journey before you start driving. It is
dangerous to plan a route while driving.
1. Tap the screen to bring up the main menu.
Note: The buttons on your ONE are shown in full color unless a button is
currently unavailable. For example, the button named Find alternative... in
the Main Menu is not available until you have planned a route.
2. Tap Navigate to...
3. Tap Address.
When you enter an address, you can choose from the following options:
• City center - tap this button to set your destination as the center of a city
or town.
• Street and house number - tap this button to set an exact address as your
destination.
• ZIP code - tap this button to enter a ZIP code as your destination.
• Cross street or intersection - tap this button to set your destination as the
point where two streets meet.
For your first trip, we will enter an exact address.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Tap Street and house number.
Note: When planning a trip for the first time your ONE asks you to choose a
state or country. Your choice is saved and used for all routes you plan.
You can change this setting at any time by tapping the state symbol or country
flag.
5. Start to type the name of the town where you want to go.
As you type, the names of the towns that match what you have typed are
shown. When your destination appears in the list, tap the name of the town
to set the destination.
6. Start to type the name of the street and select it when it is shown.
As with the name of the town, the names of the streets that match what you
have typed are shown. When your destination appears in the list, tap the
name of the street to set the destination.
7. Now enter the house number of your destination and then tap Done.
8. Your ONE asks if you need to arrive at a particular time. For this exercise,
tap NO.
The route is calculated by your ONE.
9. When the route has been calculated, tap Done.
Your ONE will immediately begin to guide you to your destination, using both
spoken instructions and on-screen directions.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Arrival times
When you plan a route, your TomTom ONE asks you if you need to arrive at a
particular time.
Tap YES to enter a preferred arrival time.
Your ONE calculates your arrival time and shows you whether you will arrive
on time.
You can also use this information to work out when you need to leave. If your
ONE shows that you will arrive 30 minutes early, you can wait and leave in 30
minutes time, rather than arrive early.
Your arrival time is constantly recalculated during your trip. The status bar
shows whether you will arrive on time or if you are going to be late, as shown
below:
You will arrive 55 minutes before the arrival time you entered.
If the estimated arrival time is more than five minutes before
the time you entered, it is shown in green.
You will arrive 3 minutes before the arrival time you entered.
If the estimated arrival time is less than 5 minutes before the
time you entered, it is shown in yellow.
You will arrive 19 minutes late.
If the estimated arrival time is later than the time you entered,
it is shown in red.
Tap Status bar preferences in the Preferences menu, to enable or disable
arrival time notifications.
Select the required options on the first menu screen and then tap Done.
To enable arrival time notifications, select Show leeway to arrival time.
To disable arrival time notifications, unselect Show leeway to arrival time.
Status bar
preferences
8
Download from Www.Somanuals.com. All Manuals Search And Download.
What are the other navigation options?
When you tap Navigate to..., you can set your destination in many ways, not
just by entering the address. The other options are listed below:
Tap this button to navigate to your Home location.
You will probably use this button more than any other.
For information about setting your Home location, see Change Home
Home
Tap this button to select a Favorite as your destination.
Favorite
Tap this button to enter an address as your destination.
3
2
1
Address
Tap this button to select your destination from a list of places you have
recently used as destinations.
Recent
destination
Tap this button to navigate to a Point of Interest (POI).
For more information about POIs and navigating to a POI, see Points of
Point of
Interest
Tap this button to select your GPS position, as your destination.
For more information about GPS, see Global Positioning System (GPS)
GPS position
Point on map
Tap this button to select a point on the map as your destination using the
map browser.
Tap this button to enter a destination using latitude and longitude values.
Latitude
Longitude
Tap this button to select your last recorded position, as your destination.
For more information about the GPS, see Global Positioning System (GPS)
Position of
last stop
Planning a route in advance
You can also use your ONE to plan trips in advance by selecting both your
starting point and your destination. You could, for example, do the following:
9
Download from Www.Somanuals.com. All Manuals Search And Download.
• Find out how long a trip is going to take before you start.
• Check the route of a trip you are planning.
• Check a route for someone who is coming to visit you so you can explain
the route to them.
To plan a route in advance, follow these steps:
1. Tap the screen to bring up the main menu.
2. Tap the arrow button to move to the next menu screen and tap Prepare
route.
Prepare route
3. Select the starting point for your trip in the same way that you would select
your destination.
4. Set the destination for your trip.
5. Choose the type of route that should be planned.
• Fastest route - the route which takes the least time.
• Shortest route - the shortest distance between the locations you set. This
may not be the quickest route, especially if the shortest route is through
a town or city.
• Avoid freeways - a route which avoids freeways.
• Walking route - a route designed for making the trip on foot.
• Bicycle route - a route designed for making the trip on a bicycle.
• Limited speed - a route for a vehicle which can only be driven at a limited
speed. You have to specify the maximum speed.
6. Your TomTom ONE plans the route between the two locations you
selected.
More information about a route
To find out about your route in detail, tap the Details button on the route
summary screen.
You can then select from the following options:
Tap this button for a list of all the turn instructions on the route.
This is very useful if you need to explain a route to someone else.
Browse as
text
Tap this button to see each turn in the trip. Tap the right and left arrows to
move forwards and backwards through the trip.
Tap the screen to turn off the 3D display and view the map from above.
Browse as
images
Tap this button to see an overview of the route using the map browser.
Browse map
of route
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Tap this button to watch a demo of the trip. You can interrupt the demo at
any time by tapping the screen.
Show route
demo
Tap this button to open the route summary screen.
Show route
summary
11
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Finding alternative routes
Finding alternative routes
Once you have planned a route, you may want to change something about the
route, without changing your destination.
Why change the route?
Maybe for one of these reasons:
• You can see a roadblock or a line of traffic ahead.
• You want to travel via a particular location, to pick someone up, stop for
lunch or fill up with gas.
• You want to avoid a difficult intersection or a road you don’t like.
Tap Find alternative... in the Main Menu to change the route that is
currently planned.
Then tap one of the options below.
Find alterna-
tive...
Tap this button to calculate an alternative to the route already planned.
Your ONE will look for another route from your current location to your
destination.
Calculate
alternative
If you decide you would prefer to use the original route after all, tap
Recalculate original.
Why would I need to do this?
Apart from the roads near your position and near your destination, the new
route will use totally different roads to reach your destination. This is an
easy way of calculating a totally different route.
Tap this button if you can see a roadblock or a line of traffic ahead. You then
have to choose how much of the route ahead you want to avoid.
Avoid
Choose from the different options: 100m, 500m, 2000m, 5000m. Your ONE
will recalculate your route avoiding the section of the route for the distance
you selected.
roadblock
Don’t forget that once a new route is calculated, you may have to turn off
the road you are on very soon.
If the roadblock suddenly clears, tap Recalculate original to return to your
original route.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Tap this button to change your route so that it passes a particular location,
perhaps to pick someone up on the way.
You choose the location you want to pass in the same way as you choose a
destination. So you can select from all the same options: for example,
Address, Favorite, Point of Interest and Point on map.
Travel via...
Your ONE will calculate a new route to your destination that passes the
location you chose.
Tap this button to return to the original route without deviations to avoid
roadblocks or traveling via particular locations.
Recalculate
original
Tap this button to avoid a part of the route. Use this button if you see that
your route includes a road or junction you don’t like, or which is well-
known for traffic problems.
Avoid part of
route
You then choose the road you want to avoid from a list of the roads on your
route.
Tap this button to recalculate your route so that it avoids traffic problems as
much as possible. Your ONE will check if there are any traffic problems on
your route and work out the best route to avoid the problems.
Minimize
traffic delays
13
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Sounds and voices
Sounds and voices
The sound on your TomTom ONE is used for features such as:
• Spoken instructions
• Warnings
How do I change the volume level?
You can change the volume in three ways:
• Tap the bottom left hand area of the Driving View. The last spoken
instruction is repeated and the volume level is shown.
Move the volume slider to adjust the volume.
• In the Main Menu, tap Change preferences, then tap Volume preferences.
Tap Test to check your changes.
Changing the volume automatically
Your TomTom ONE can change the volume automatically.
1. In the Main Menu, tap Change preferences.
2. Tap Volume preferences.
Volume
preferences
3. Select Link volume to car speed.
4. Tap Done.
Selecting a voice
To change the voice being used by your TomTom ONE, tap Change voice in
the Preferences menu and select a voice from the list.
Change voice
14
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Help me!
Help me!
Help me! provides an easy way to navigate to emergency services centers and
other specialist services and contact them by phone.
For example, if you are involved in a car accident, you could use Help me! to
call the nearest hospital and tell them your exact location.
How do I use Help me! to call a local service?
You can use Help me! to find and make contact with a service center.
When you select a service center, your current location and the phone number
of the POI are shown.
To use Help me! to locate a service center, contact the center by phone and
navigate from your current location to the center, do the following:
1. Tap the screen to bring up the main menu.
2. Tap Help me!
3. Select the type of service you require, for example, Nearest hospital.
4. Select a center from the list; the nearest is shown at the top of the list.
Your ONE shows the location of the service center on the map and the
contact details.
5. To navigate your way to the center on foot, tap Walk there.
Your ONE starts guiding you to your destination.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Options
Use your TomTom ONE to find the location of a service and the contact
details.
• Emergency services
• Emergency breakdown services
• Nearest police station
• Nearest doctor
Phone for help
• Nearest hospital
• Nearest public transport
• Nearest car repair services
• Nearest dentist
• Nearest pharmacy
• Nearest vet
Note: In some countries, information may not be available for all services.
Use your TomTom ONE to navigate your way by road to a service center.
• Nearest car repair services
• Nearest hospital
Drive to help
• Nearest doctor
• Nearest police station
• Nearest pharmacy
• Nearest dentist
Note: In some countries, information may not be available for all services.
Use your TomTom ONE to navigate your way on foot to a service center.
• Nearest gas station
• Nearest public transport
• Nearest police station
• Nearest pharmacy
• Home
Walk to help
• Nearest doctor
Note: In some countries, information may not be available for all services.
Your TomTom ONE shows your current location.
You can then tap Phone for help to select the type of service you want to
contact.
Where am I?
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Tap this button to read the British Red Cross First Aid guide.
Tap this button to read a selection of useful guides.
First Aid
Guide
Other guides
17
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Favorites
Favorites
What are Favorites?
Favorites are places that you often visit. You can create Favorites so that you
don’t have to enter the address every time you want to navigate there.
They don’t have to be places you especially like, just useful addresses.
How can I create a Favorite?
From the Main Menu, tap Add Favorite.
Note: The button Add Favorite may not be shown on the first page of the Main
Menu. Tap the arrow to open other pages in the Main Menu.
You can then select the location of the Favorite from the list below.
Give your Favorite a name that is easy to remember. Your ONE will always
suggest a name, usually the address of the Favorite. To enter the name, just
start typing. You don’t have to delete the suggested name.
You can set your Home location as a Favorite.
Home
You cannot create a Favorite from another Favorite. This option will always
be unavailable in this menu.
To rename a Favorite, tap Manage Favorites in the Preferences menu.
Favorite
You can specify an address to be a Favorite. When you enter an address,
you can choose from four options.
3
2
1
• City center
Address
• Street and house number
• ZIP code
• Crossing or intersection
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Select a Favorite location from a list of places you have recently used as
destinations.
Recent
destination
You can add a Point of Interest (POI) as a Favorite.
Does it make sense to do this?
If you visit a POI you particularly like, for example a restaurant, you can add
it as a Favorite.
Point of
Interest
To add a POI as a Favorite, tap this button, then do the following:
1. Narrow your choice of POIs by selecting the area where the POI is.
You can select one of these options:
• POI near you - to search from a list of POIs near your current position.
• POI in city - to choose a POI in a particular town or city. You have to
specify a town or city.
• POI near Home - to search from a list of POIs near your Home
location.
If you are currently navigating to a destination, you can also select from
a list of POIs which are on your route or near your destination. Choose
one of these options:
• POI along route
• POI near destination
2. Select the category of POI.
Tap the category of POI if it is shown or tap the arrow to choose from
the complete list.
Tap Any POI category to search for a POI by name.
Tap this button to add your current position as a Favorite.
For example, if you stop somewhere interesting, while you are there you
can tap this button to create the Favorite.
My location
Tap this button to create a Favorite using the map browser.
Select the location of the Favorite using the cursor, then tap Done.
Point on map
Tap this button to create a Favorite by entering latitude and longitude
values.
Latitude
Longitude
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Tap this button to select your last recorded position as your destination.
For more information about the GPS, see Global Positioning System (GPS)
Position of
last stop
How can I use a Favorite?
You will normally use a Favorite as a way of navigating to a place without
having to enter the address. To navigate to a Favorite, do the following:
1. Tap the screen to bring up the main menu.
2. Tap Navigate to...
3. Tap Favorite.
4. Select a Favorite from the list.
Your ONE calculates the route for you.
5. When the route is calculated, tap Done.
Your ONE will immediately start guiding you to your destination with spoken
instructions and visual instructions on the screen.
How many Favorites can I create?
You can create up to 48 Favorites. If you want to add more than 48, we suggest
that you make some POI categories and add some of your Favorites as POIs.
How can I delete a Favorite?
1. Tap the screen to bring up the main menu.
2. Tap Change preferences to open the Preferences menu.
3. Tap Manage Favourites.
Tip: Tap the arrow to move to the next page.
4. Tap the Favorite you want to delete.
5. Tap Delete.
How can I change the name of a Favorite?
1. Tap the screen to bring up the main menu.
2. Tap Change preferences to open the Preferences menu.
3. Tap Manage Favorites.
Tip: Tap the arrow to move to the next page of buttons.
4. Tap the Favorite you want to rename.
5. Tap Rename.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Browse map
Browse map
To look at the map in the same way as you might look at a traditional paper
map, tap Browse map in the Main Menu.
You can move the map by touching the screen and moving your finger across
the screen.
AThe scale bar
BYour current position.
CGPS button
Tap this button to center the map on your current position.
DOptions
EThe cursor
FThe Find button
Tap this button to find specific addresses.
GThe Cursor button
Tap this button to navigate to the cursor position, make a Favorite of the
cursor position, or find a Point of Interest near the cursor position.
HThe zoom bar
Zoom in and out by moving the slider.
Cursor button
You can use the map to find addresses and Points of Interest (POIs), for
example, restaurants, train stations and gas stations.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Tap the cursor button then tap one of the following buttons:
Tap this button to navigate to the cursor position. Your ONE will calculate
the route.
Navigate
there
Tap this button to bring the location currently highlighted by the cursor to
the center of the screen when looking at the map.
Center on
map
Tap this button to create a Favorite at the cursor position.
Add as
Favorite
22
Download from Www.Somanuals.com. All Manuals Search And Download.
10. Points of Interest
Points of Interest
Points of Interest or POIs are useful places on the map. Here are some
examples:
• Restaurants
• Hotels
• Museums
• Parking garages
• Gas stations
Showing POIs on the map
1. Tap Show POIs on map in the Preferences menu.
Show POI on
map
2. Select the POI categories to display on the map.
Tap Find to search for a POI by name.
3. Tap Done.
The POIs you have selected are shown as symbols on the map.
Navigating to a POI
You can use a POI as your destination. For example, if you are traveling to an
unfamiliar city, you could choose a POI to help find a parking garage.
1. Tap the screen to bring up the main menu.
2. Tap Navigate to... in the Main Menu.
3. Tap Point of Interest.
4. Tap POI in city.
5. Narrow your choice of POIs by selecting the area where the POI is located.
You can select one of these options:
• POI near you - to choose from a list of POIs near to your current location.
• POI in city - to find a POI in a particular town or city.
• POI near Home - to choose from a list of POIs near to your Home location.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
You can select from a list of POIs which are along your route or close to your
destination. Choose from one of these options:
• POI along route
• POI near destination
6. Type the name of the town you want to visit and select the town when it
appears in the list.
7. Tap Parking garage.
8. Select the category of POI:
Tap Any POI category to search for a POI by name.
Tap the category of POI, if it is shown.
Tap the arrow to choose from the complete list of categories. Select the
category from the list or start to type the name of the category and select it
when it appears in the list.
9. Select a parking garage. The distance listed next to each POI is the distance
from the city center.
10.From the list of POIs shown, select the POI you want to navigate to.
The table below explains the distances listed next to each POI.
POI near you
POI in city
Distance from your current location
Distance from the city center
POI near Home
Distance from your Home location
Distance from your current location
POI along
route
POI near
destination
Distance from your destination
Last POI
Distance to the last POI you visited
If you know the name of the POI, tap Find and type the name. Select it from
the list when it is shown.
11.Select a parking garage. The distance listed next to each POI is the distance
from the city center.
Once you have selected a POI, the route to the POI is calculated by your
TomTom ONE.
The route to the POI is then calculated by your TomTom ONE.
How can I set warnings for POIs?
1. Tap the screen to bring up the main menu.
2. Tap Change preferences.
3. Tap Manage POIs.
Note: The Manage POIs button is only available when all menu buttons are
shown. To show all menu buttons, tap Show ALL menu options in the
Preferences menu.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Tap Warn when near POI.
Tap this button to receive a warning when you travel near to the location
of a POI.
Warn when
near POI
5. Select the category of POI you want to be warned about.
Select the category from the list or start to type the name of the category
and select it when it is shown in the list.
6. Set how close the POI should be when you receive a warning.
7. Choose the warning sound for the category of POI you selected.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
11. Preferences
Preferences
You can change the way your TomTom ONE looks and behaves.
Tap Change preferences in the Main Menu.
Use night colors / Use day colors
Tap this button to reduce the brightness of the screen and show darker
colors on the map.
When should I use this?
Use night
colors
When it’s dark, it is easier to see the screen if the display on your ONE is not
brightly lit.
To change back to a brighter screen showing brighter colors on the map,
tap Use day colors.
Use day colors
Show POI on map
Tap this button to set which categories for the Points of Interest (POIs)
should be shown on the map.
Select the POIs that you want to see on the map from the list.
Show POI on
map
When you select a POI, it is shown on the map using the symbol you can
see next to each category in the list.
To find a POI category quickly, tap Find, then start to type the name of the
POI category. As soon as the category is shown in the list, you can select it.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety preferences
Tap this button to set the following safety preferences:
• Hide most menu options while driving
• Suggest driving breaks
Safety
preferences
• Show safety reminders
• Warn when near places of worship or schools
• Warn when driving faster than allowed
• Warn when driving faster than a set speed
• Warn not to leave the device in the car
If you select one or more of the warnings, you will also be asked to select a
sound to be played whenever a warning is displayed.
Select whether or not your TomTom ONE should warn you about which
side of the road you should be driving on.
Decide if you want the map display to be turned off in special
circumstances and press Done.
What happens when I use the Turn off map display option?
When you turn off the map display, instead of seeing your position on a map
in the Driving View, you will only see information about the next instruction.
Tap the button and select an option for when the map should be turned off.
These are the options:
• Always - The map will not be shown and you will only see information
about the next instruction and arrows showing direction.
• Above a certain speed - you set the speed at which point the map will be
turned off. This option is useful for situations when the map might be
distracting, such as when you are driving fast.
• Never - the map is never turned off.
Turn off sound / Turn on sound
Tap this button to turn off spoken instructions.
The button changes to Turn on sound. If you turn off the sound, warnings
for upcoming POIs are also turned off.
Turn off sound
Tips
To change the volume, tap Volume preferences in the Preferences menu.
To change the volume quickly while you are driving, tap the bottom left-
hand section of the Driving View and move the slider.
To change the voice being used by your ONE, tap Change voice in the
Preferences menu.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Volume preferences
Tap this button to change the volume for spoken instructions.
Volume
preferences
Manage Favorites
Tap this button to rename or delete Favorites.
To find a Favorite quickly, tap Find, then start to type the name of the
Favorite. As soon as the Favorite is shown in the list, you can select it.
Manage
Favorites
TomTom Safety Cameras
Tap this button to use TomTom Safety Cameras.
TomTom
Safety
Cameras
Change voice
Tap this button to change the voice that is used for announcing command
directions.
Change voice
Warn when near POI
Tap this button to announce a warning when your are approaching a Point
of Interest.
Warn when
near POI
Change Home location
Tap this button to set or change your Home location.
Change Home
location
Do I need to use my actual home address for the Home location?
28
Download from Www.Somanuals.com. All Manuals Search And Download.
No. Your Home location can be a place you go often, for example, your office.
It can be your actual home address, but it can also be any address you like.
Why should I set a Home location?
Having a Home location means that you have a quick and easy way to navigate
there, by tapping the Home button in the Navigate to... menu
Manage maps
Tap this button to do the following:
• Download a map - you can buy new maps using TomTom HOME.
Manage maps
• Switch map - tap this button to change the map you are using.
• Delete a map - tap this button to delete a map. This might be necessary
to create more space on your ONE, for example when you want to load
a different map.
Note: Don’t delete a map unless you have already made a backup of the
map. If you delete a map before you make a backup, you will no longer be
able to load the map on your ONE.
For more information about making a backup, see Using TomTom HOME
(43).
You can also download, add and delete maps using TomTom HOME.
Change 2D/3D display / Turn on 2D display
Tap Turn on 2D display to change the perspective for viewing the map.
For example, the 2D view shows a two dimensional view of the map as
though viewed from above.
Turn on 2D
display
To switch the view to a three dimensional perspective, tap Change 2D/3D
display and select a view from the list.
Change2D/3D
display
When should I use this?
In some situations, it is easier to see the map from above. Perhaps if the road
network is complicated or for times when you are walking while using your
ONE to navigate.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Compass preferences
Tap this button to configure the compass. The following options are
available:
• None - the compass is not shown.
Compass
• One with arrow pointing north - the arrow always points towards north
preferences
and the direction you are moving is shown at the top of the compass.
• One with arrow showing your heading - the arrow always shows the
direction you are moving.
If you select one of these options, you then need to select the features
that are shown in the middle of the arrow:
• Direction - your direction is shown as a compass point, displayed in
the center of the compass arrow.
• Degrees - your direction is shown as compass degrees, displayed in
the center of the compass arrow.
• Nothing
• One with arrow pointing to your destination - the arrow always points
towards your destination. The distance to your destination is displayed
in the compass arrow.
Change map colors
Tap this button to select the color schemes for day and night map colors.
You can also download more color schemes from TomTom PLUS.
Change map
colors
Brightness preferences
Tap this button to set the brightness of the screen.
You can set the brightness separately for day map colors and for night map
colors.
Brightness
preferences
You can set the map color scheme by tapping Change map colors. For
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Status bar preferences
Tap this button to select the information shown on the status bar:
• Remaining time - the estimated time left until you reach your destination.
• Remaining distance - the distance left until you reach your destination.
• Current time
Status bar
preferences
• Arrival time - your estimated arrival time.
• Speed
• Direction
• Show next street name - the name of the next street on your trip.
• Show current street name
• Show leeway to arrival time - your ONE shows how late or early you will
be compared with the preferred arrival time that is set during the
planning of a route.
• Show max speed next to speed - only available when speed (above) is
also selected.
• How should the status bar be displayed?
Horizontal - If you choose this option, the status bar will be shown at the
bottom of the Driving view.
Vertical - If you choose this option, the status bar will be shown at the
right-hand side of the Driving view.
Note: If the speed limit for the road you are on is available, it is shown next
to your speed.
If you drive faster than the speed limit, your speed is shown in red.
Guided tours
Tap this button to show one of the Guided tours on how to use your
TomTom ONE.
Guided tours
Set units
Tap this button to set the type of units that will be shown for the following:
• Distance
• Time
Set units
• Latitude and longitude
• Temperature
• Air pressure
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Operate left-handed / Operate right-handed
Tap this button to move important buttons, for example, the Done and
Cancel buttons as well as the zoom bar, to the left hand side of the screen.
This makes it easier to tap the buttons with your left hand without blocking
the screen.
Operate left-
handed
To move the buttons back to the right hand side of the screen, tap Operate
right-handed.
Keyboard preferences
You use the keyboard to enter your destination or to find an item in a list,
such as a POI.
Tap this button to select the size of the keys on the keyboard and the
keyboard layout. You can select from two sizes:
Keyboard
preferences
• Large keyboard
• Small keyboard
Three keyboard layouts are available:
• ABCD keyboard
• QWERTY keyboard
• AZERTY keyboard
Note: The keyboard does not include accents of any kind for any language
so you don’t have to worry about entering letters with accents. Simply type
the letter without the accent and your ONE will recognize the word.
Planning preferences
Tap this button to set the kind of route planned when you select a
destination.
The following options are available:
• Ask me every time I plan
• Always plan fastest routes
• Always plan shortest routes
• Always avoid freeways
Planning
preferences
• Always plan walking routes
• Always plan bicycle routes
• Always plan for limited speed
Then answer the following question:
Do you want the route summary screen to close automatically after 10
seconds?
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Set owner
Tap this button to enter your name and address as the owner of your ONE
and to change or delete a 4-digit password for your ONE.
Note: You can only change or delete a 4-digit password on your
TomTom ONE.
Set owner
You can create a 4-digit password for your ONE using TomTom HOME:
1. Connect your ONE to your computer and turn on your ONE and your
computer.
TomTom HOME starts automatically.
For information about installing TomTom HOME on your computer, see
2. From the Options menu in TomTom HOME, click My ONE.
3. Click the ON/OFF button on the picture of your ONE to start the
application on your computer.
4. From the Main Menu, click Change preferences.
5. Click Set Owner. You can now set a 4-digit password for your ONE.
You can only create a 4-digit password using TomTom HOME.
Change language
Tap this button to change the language used for all the buttons and
messages you see on your ONE.
You can choose from a wide range of languages. When you change the
language, you are also given the opportunity to change the voice.
Change
language
Set clock
Tap this button to select the type of clock that is shown and set the time.
The easiest way to set the time is by tapping the Sync button. Your ONE will
then take the time from GPS information.
Set clock
For more information about GPS, see Global Positioning System (GPS)
(42).
Note: After using Sync to set the time, you may have to adjust the hours
depending on your time zone. Your ONE works out your time zone and
always keeps the time correct using GPS information.
You can only use Sync if you have GPS reception, so you cannot set the
clock in this way when you are indoors.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Reset factory settings
Tap this button to restore the factory settings to your TomTom ONE.
All your settings, including Favorites, your Home location, warnings for
POIs and any Itineraries you have created, as well as recent destinations
and recent calls and callers, will be deleted.
Reset factory
settings
34
Download from Www.Somanuals.com. All Manuals Search And Download.
12. Traffic information using RDS-TMC
Traffic information using RDS-TMC
The Traffic Message Channel (TMC)
The Traffic Message Channel (TMC) is not a TomTom Service. FM radio
stations in several countries broadcast TMC information as part of their
programming. TMC is also known as RDS-TMC traffic information.
Your TomTom device uses this information to warn you about traffic delays
along your route and how you can avoid them.
To use TMC traffic information, you need a TomTom RDS-TMC Traffic
Receiver that comes with some TomTom devices or is available as an
accessory for others. For more information on which TomTom devices
Note: TomTom is not responsible for the availability or quality of traffic
information provided by TMC.
check if it is available in your country or region.
Setting up TMC
To start using TMC, all you need to do is connect the RDS-TMC Traffic
Receiver to your TomTom device or to the windscreen mount of your
TomTom device, depending on your product.
The receiver works best when mounted in a vertical position, so if possible, try
to place your TomTom device towards the drivers side corner of the
windscreen so that the receiver can be secured out side of your field of vision.
After you have finished positioning the receiver switch your TomTom device
on. The Traffic sidebar is shown on the right-hand side of the Driving View and
your device searches for a radio station that has RDS-TMC information.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
The following symbols are shown at the top of the Traffic sidebar:
Your device is looking for a radio station with RDS-TMC traffic
information.
Your device has found a suitable radio station and is checking for
the latest traffic information.
Your device is tuned to a radio station and receives RDS-TMC
traffic information when available.
Tip: The yellow circle is shown at the top of the Traffic sidebar if your device
cannot find a suitable radio station. You can make your device try again to find
a suitable station by tapping Tune automatically in the traffic menu. If you
know the FM frequency of a station that broadcasts RDS-TMC traffic
information, you can tune to it manually. For more information see Setting the
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Using RDS-TMC traffic information
Your device receives traffic information when it is broadcasted.
If there are any incidents on your route the Traffic sidebar on the right side
of the Driving View warns you. An example of a Traffic sidebar with a traffic
In the example on the left there is a traffic jam on your route with an
expected delay of 38 minutes, 20 miles ahead of you. To find the quickest
route to your destination, do the following:
38 min
20
1. Tap the Traffic sidebar.
M
Tip: If you have trouble tapping the Traffic sidebar and the Main Menu is
being displayed instead of the traffic menu, try tapping your finger half on
the Traffic sidebar and half off the screen.
2. Tap Minimize traffic delays.
Your device looks for the quickest route to your destination.
It is possible that the new route may also include traffic delays, or may
even be the same route as before. You can re-plan the route to avoid all
delays, but this new route will take longer than the quickest route already
shown.
3. Tap Done.
Tip: It is possible to let your TomTom device automatically minimize traffic
Changing traffic preferences
Use the Change Traffic preferences button to choose how traffic information
works on your device.
To change your traffic preferences, do the following:
1. Tap the TomTomTraffic button in the Main Menu on your device.
2. Tap Change Traffic preferences.
Change
Traffic
preferences
You can change the following preferences:
• Automatically minimize delays after every traffic update - if you select
this option, your device automatically recalculates when new delays
occur on your route.
• Beep when traffic situation on route changes - if you select this option
your device beeps when a new traffic incident occurs on your current
route.
• Ask for traffic updates when preparing a route - this option has no
effect in RDS traffic.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Select or clear the check box next to each preference you want to change.
4. Tap Done.
Your device lists the countries that have radio stations providing RDS-
TMC traffic information that you can currently receive. Normally you can
leave this set to Any country (strongest signal). For more information
about this country setting, see Choosing the correct country for RDS-
5. Tap Done.
Making commuting to work easier
The Home to work or Work to home buttons in the Traffic menu lets you
check your route to and from work with one tap of a button. When you use
either of these buttons, your device checks the route for possible delays, and
if it finds any, provides you with the possibility to avoid them.
The first time you use Home to work, you must set your traffic home and work
locations, do the following:
1. Tap the TomTomTraffic button in the Main Menu on your device.
2. Tap Show home-work traffic.
3. Tap Change home-work
Change home-
work
4. Set your home location
5. Set your work location.
You can now use the Home to work and Work to home buttons of the Show
home-work traffic menu.
For example, to check for delays on your route home, do the following:
1. Tap the TomTomTraffic button in the Main Menu on your device.
2. Tap Show home-work traffic.
3. Tap Work to home.
The route summary screen is shown.
To see if there is a quicker way home, you could now tap the Find alternative
button and then tap Minimize traffic delays.
Tip: You can let your device automatically look for alternative routes by
selecting Automatically minimize delays after every traffic update in your
Traffic preferences. For more information, see Changing traffic preferences
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Note: It is possible that the alternative route could be longer than your original
one (even with its delays). If this is the case, you could always try using the
Find alternative button again.
Setting the radio frequency for RDS-TMC information
If you know the frequency of a particular radio station you want to use for RDS-
TMC traffic information, do the following to set the frequency manually:
1. Tap the Traffic sidebar in the Driving View.
2. Tap Tune Manually.
3. Enter the frequency of the radio station.
4. Tap Done.
Tune manually
Your TomTom device looks for your radio station. If it doesn't find a radio
station at the frequency you set, it automatically continues to search for the
next available station.
Choosing the correct country for RDS-TMC reception
If you are driving close to a country border, your device may tune to a radio
station from a neigboring country. If this happens you will only receive RDS-
TMC traffic information for that country. To set the country you want to receive
traffic information for, do the following:
1. Tap the Traffic sidebar in the Driving View.
2. Tap Change Traffic preferences.
A list of preferences you can choose is shown, these preferences are
3. Tap Done.
A list of neigboring countries is shown.
4. Tap on the country that you want to receive traffic reports for.
Your TomTom device then searches for a radio station in the country you have
chosen.
The Traffic sidebar
The Traffic sidebar is shown on the right side of the Driving View when
TomTom Traffic is switched on. The Traffic sidebar shows you the traffic
incidents on your route. It shows the following information:
• A symbol for each traffic incident in the order they occur along your
planned route.
• The estimated delay to the next traffic incident on your route.
• The distance from your current location to the next incident on your route.
An example of a Traffic sidebar is shown below.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
In the example, the Traffic sidebar shows you that there are two incidents
ahead. Both incidents are traffic jams, the first is 15 miles ahead and is
expected to delay you by at least 51 minutes.
To re-plan your route to avoid these incidents, tap the Traffic sidebar to open
the TomTom traffic menu, then use Minimize traffic delays. For more
Traffic incidents
Traffic incidents are displayed both on the Driving View and also on the Traffic
sidebar as small symbols. There are two type of symbols:
• Symbols shown in a red square are incidents that Traffic can help you avoid.
• Symbols shown in a red rectangle are weather related, because of their
nature, you cannot use Traffic to avoid them.
Traffic incident symbols and their meaning are shown below:
Accident
Road closed
Traffic incident
Traffic jam
Road works
One or more lanes
closed
Weather related symbols and their meaning are shown below:
Fog
Ice
Rain
Wind
Snow
Note: The incident avoided symbol is shown for any traffic incident that
you avoid using TomTom Traffic.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Traffic menu
Tap the Traffic sidebar in the Driving View to open the Traffic menu. The
following buttons are available:
Tap this button to re-plan your route based on the latest traffic
information.
Minimize
traffic delays
Tap this button to get your device to automatically search for a radio
frequency that carries RDS-TMC traffic information.
Tune automati-
cally
Note: Your TomTom device automatically searches for a suitable radio
station, use this button to force your device to search for the next suitable
station.
Tap this button to get your device to tune to a specific radio frequency
that carries RDS-TMC traffic information.
Tune manually
Tap this button to show areas of traffic congestion along your current
route.
Showtrafficon
route
Tap this button to calculate and show the quickest route from your home
location to your place of work and back.
Show home-
work traffic
Tap this button to change your preferences for how TomTom Traffic
works on your device.
Change Traffic
preferences
41
Download from Www.Somanuals.com. All Manuals Search And Download.
13. How Does Navigation Work?
How Does Navigation Work?
Global Positioning System (GPS)
In order to navigate you to your destination, your TomTom ONE must know
where you are now. To find your current position, your ONE uses the Global
Positioning System (GPS). GPS is available for free and without subscription.
GPS uses satellites to transmit signals to GPS receivers. Your TomTom ONE
has a built-in GPS receiver. Using the GPS signal, your ONE can work out
where you are and how fast you are going. GPS signals work in all weather,
anywhere in the world.
Note: Your TomTom ONE does not transmit your position, so others cannot
use it to track you while you are driving.
Maps
Once your TomTom ONE knows where you are and you have told it where
you want to go, it uses the digital map on the memory card or hard disk to
work out the best route to your destination.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
14. Using TomTom HOME
Using TomTom HOME
TomTom HOME is a free software program for your computer that enables
you to:
• Manage maps, voices, POIs and more.
• Buy TomTom services and manage your subscriptions.
• Update your TomTom with the latest software and services automatically.
• Make and restore backups.
• Set a password to restrict access.
• Read the full version of the user manual.
Installing TomTom HOME
Install TomTom HOME on your computer in the following way.
• Connect your computer to the Internet and then connect your
TomTom ONE to your computer using the USB cable.
A pop-up window appears. Select Run TomTom HOME. Click OK and
follow the on-screen instructions.
If the pop-up window does not appear, browse to the TomTom device on
your computer and run the file named Install TomTom HOME.
• TomTom HOME is also available for download from the TomTom Web site.
For more information visit www.tomtom.com/home
Once installed, TomTom HOME will start automatically whenever you connect
your TomTom to your computer.
HOME Help Topics
In the TomTom HOME Help topics you can find all kinds of tips and tricks on
how to use TomTom HOME.
MyTomTom Account
In order to buy content and services through TomTom HOME you will have to
set up a MyTomTom account for the device you want to buy the content for.
You will be asked to create an account when you start using TomTom HOME.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
15. TomTom Limited Warranty
TomTom Limited Warranty
WARRANTOR
U.S. and Canadian Purchases: If you have made your purchase in the United
States or Canada, this Limited Warranty is granted by and this Limitation of
Liability is stipulated for the benefit of TomTom Inc., 150 Baker Avenue
Extension, Concord Massachusetts 01742 (United States of America).
WHAT THIS WARRANTY COVERS
1) TomTom Inc. (“TomTom”) warrants to the original purchaser (“you”) of the
hardware with which this Limited Warranty is included (“Hardware”) that the
Hardware will be free from defects in workmanship and materials under
normal use (“Defects”) for a period of one (1) year from the date that the
Hardware was first purchased by you (“Warranty Period”). During the
Warranty Period the Hardware will be repaired or replaced at TomTom’s
choice (“Limited Warranty”) without charge to you for either parts or labour.
This Limited Warranty covers the replacement of the Hardware only. If the
Hardware is repaired after the Warranty Period has expired, the Warranty
Period for the repair will expire six (6) months after the date of repair.
WHAT THIS WARRANTY DOES NOT COVER
2) The Limited Warranty does not apply to normal wear and tear, does not
apply when the Hardware is opened or repaired by someone not authorized
by TomTom and does not cover repair or replacement of any Hardware or part
thereof damaged by: misuse, moisture, liquids, proximity or exposure to heat
and accident, abuse, non-compliance with the instructions supplied with the
Hardware, neglect or misapplication. The Limited Warranty does not cover
physical damage to the surface of the Hardware. This Limited Warranty does
not cover any software that may accompany or be installed on the Hardware.
The Limited Warranty does not cover the installation, removal or maintenance
of the Hardware or any costs related herewith.
HOW TO MAKE A WARRANTY CLAIM
3) In order to make a claim of a Defect, you must contact TomTom during the
explain the Defect and to obtain an RMA number (Return Materials
Authorization) if necessary. You must return the Hardware during the
Warranty Period, along with an explanation of the Defect, to the address
provided to you by TomTom. If a defect arises and a valid claim under this
Limited Warranty is received by TomTom after the first one hundred and
eighty (180) days of the Warranty Period, TomTom is entitled to charge you
for any reasonable shipping and handling costs made in connection with the
repair or replacement of the Hardware. You must comply with any other return
procedures stipulated by TomTom, if any.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
YOUR LEGAL RIGHTS
4) This Limited Warranty gives you specific legal rights, and you may also have
other rights which vary from state to state and jurisdiction to jurisdiction.
5) If any part of this Limited Warranty is held to be invalid or unenforceable,
the remainder of the Limited Warranty shall nonetheless remain in full force
and effect.
6) This Limited Warranty is the only express warranty made to you and is
provided in lieu of any other express warranties or similar obligations (if any)
created by any advertising, documentation, packaging, or other
communications.
7) Except for the Limited Warranty and to the maximum extent permitted by
applicable law, TomTom and its suppliers provide the Hardware "AS IS AND
WITH ALL FAULTS", and hereby disclaim all other warranties and conditions,
whether express, implied or statutory, including, but not limited to, any (if any)
implied warranties, duties or conditions of: merchantability, non-
infringement, quiet enjoyment, system integration, satisfactory quality, fitness
for a particular purpose, reliability or availability, accuracy or completeness of
responses, results, workmanlike effort, lack of viruses, and reasonable care
and skill, all with regard to the Hardware, and the provision of or failure to
provide support or other services, information, software, and related content
through the Hardware or otherwise arising out of the use of the Hardware. This
exclusion does not apply to (i) any implied condition as to title and (ii) any
implied warranty as to conformity with description. If applicable law requires
any implied warranties with respect to the Hardware, all such warranties are
limited in duration to ninety (90) days. Some states and/or jurisdictions do not
allow limitations on how long an implied warranty lasts, so the above may not
apply to you.
8) This Limited Warranty cannot be transferred to any other person.
LIMITATION OF LIABILITY
9) Neither TomTom nor its suppliers shall be liable to you or to any third party
for any indirect, incidental, consequential, special or exemplary damages
(including in each case, but not limited to, damages for the inability to use the
equipment or access data, loss of data, loss of business, loss of profits,
business interruption or the like) arising out of the use of or inability to use the
Hardware even if TomTom has been advised of the possibility of such
damages.
10) Notwithstanding any damages that you might incur for any reason
whatsoever (including, without limitation, all damages referenced herein and
all direct or general damages in contract or anything else), the entire liability
of TomTom and any of its suppliers shall be limited to the amount actually
paid by you for the Hardware.
11) Notwithstanding the above, neither party's liability for death or personal
injury resulting from its own negligence shall be limited.
12) Some states and/or jurisdictions do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitations or exclusions
may not apply to you.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
16. Addendum
Addendum
Important Safety Notices and Warnings
Global Positioning System
The Global Positioning System (GPS) is a satellite-based system that provides
location and timing information around the globe. GPS is operated and
controlled under the sole responsibility of the Government of the United
States of America which is responsible for its availability and accuracy. Any
changes in GPS availability and accuracy, or in environmental conditions, may
impact the operation of your TomTom device. TomTom does not accept any
liability for the availability and accuracy of GPS.
Use with Care
Use of a TomTom device for navigation still means that you need to drive with
due care and attention.
Aircraft and Hospitals
Use of devices with an antenna is prohibited on most aircraft, in many
hospitals and in many other locations. A TomTom device must not be used in
these environments.
Battery
This product uses a Lithium-Polymer battery. Do not use it in a humid, wet
and/or corrosive environment. Do not put, store or leave your product in or
near a heat source, in a high temperature location, in strong direct sunlight, in
a microwave oven or in a pressurized container, and do not expose it to
temperatures over 60 C (140 F). Failure to follow these guidelines may cause
the Lithium-Polymer battery to leak acid, become hot, explode or ignite and
cause injury and/or damage. Do not pierce, open or disassemble the battery.
If the battery leaks and you come into contact with the leaked fluids, rinse
thoroughly with water and seek medical attention immediately. For safety
reasons, and to prolong the lifetime of the battery, charging will not occur at
low (below 0 C/32 F) or high (over 45 C/113 F) temperatures.
Temperatures: Standard operation: -10 C (14 F) to +55 C (131 F); short period
storage: -20 C (-4 F) to + 60 C (140 F); long period storage: -20 C (-4 F) to
+25 C (77 F).
THE LITHIUM-POLYMER BATTERY CONTAINED IN THE PRODUCT
MUST BE RECYCLED OR DISPOSED OF PROPERLY. USE YOUR
TomTom ONLY WITH THE SUPPLIED DC POWER LEAD (CAR
CHARGER/BATTERY CABLE) AND AC ADAPTER (HOME CHARGER)
FOR BATTERY CHARGING.
To recycle your TomTom unit please see your local approved TomTom
service center.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIAL NOTE REGARDING DRIVING IN CALIFORNIA AND MINNESOTA
California Vehicle Code Section 26708 (a) (1) provides that “No persons shall
drive any motor vehicle with an object or material placed, displayed, installed,
affixed or applied upon the windshield or side or rear windows.” Drivers in
California should not use a suction mount on their windshield, side or rear
windows.
Note: this section of the California Vehicle Code applies to anyone driving in
California, not just California residents.
Minnesota State Legislature Statutes Section 169.71, subdivision 1, section 2
provides that “A person shall not drive or operate with any objects suspended
between the driver and the windshield other than sun visors and rearview
mirrors and electronic toll collection devices.”
Note: this Minnesota Stature applies to anyone driving in Minnesota, not just
Minnesota residents.
TomTom Inc. bears no responsibility for any fines, penalties or damage that
may be incurred by disregarding this notice. While driving in any state with
windshield mounting restrictions, TomTom recommends the use of the
supplied Adhesive Mounting Disk or its Alternative Mounting Kit, which
includes multiple options for mounting TomTom devices on the dashboard
this mounting option.
FCC Information for the User
This product contains a transmitter which must not be co-located or
simultaneously operated in conjunction with any other transmitter.
Exposure to Radio Frequency Radiation
This device complies with FCC radiation exposure limits set forth for an
uncontrolled environment. In order to avoid the possibility of exceeding the
FCC radio frequency exposure limits, human proximity to the antenna shall
not be less than 20cm (8 inches) during normal operation.
Radio and Television Interference
This equipment radiates radio frequency energy and if not used properly - that
is, in strict accordance with the instructions in this manual - may cause
interference to radio communications and television reception.
This device has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiated radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation distance between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user‘s authority to operate the equipment.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Important
This equipment was tested for FCC compliance under conditions that included
the use of shielded cables and connectors between it and the peripherals. It is
important that you use shielded cable and connectors to reduce the possibility
of causing radio and television interference. Shielded cables, suitable for the
product range, can be obtained from an authorised dealer. If the user modifies
the equipment or its peripherals in any way, and these modifications are not
approved by TomTom, the FCC may withdraw the user’s right to operate the
equipment. For customers in the USA, the following booklet prepared by the
Federal Communications Commission may be of help: “How to Identify and
Resolve Radio-TV Interference Problems”. This booklet is available from the
US Government Printing Office, Washington, DC 20402. Stock No 004-000-
00345-4.
FCC Declaration of Conformity
Tested to Comply with FCC Standards for Home or Office Use
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference
that may cause undesired operation.
Responsible party in North America
TomTom, Inc., 150 Baker Avenue, Concord, MA 01742
Tel: 866 486-6866 option 1 (1-866-4-TomTom)
Emissions information for Canada
This Class B digital apparatus complies with Canadian ICES-003. Cet appareil
numérique de la classe B est conforme à la norme NMB-003 du Canada.
C-tick
N14644
This product displays the C-tick to show it complies with all relevant
Australian and New Zealand regulations.
Warning for Australia
The user needs to switch off the device when exposed to areas with
potentially explosive atmospheres such as petrol stations, chemical storage
depots and blasting operations.
This Document
Great care was taken in preparing this manual. Constant product development
may mean that some information is not entirely up-to-date. The information in
this document is subject to change without notice.
TomTom shall not be liable for technical or editorial errors or omissions
contained herein; nor for incidental or consequential damages resulting from
the performance or use of this material. This document contains information
protected by copyright. No part of this document may be photocopied or
reproduced in any form without prior written consent from TomTom
International B.V.
Part numbers
48
Download from Www.Somanuals.com. All Manuals Search And Download.
TomTom ONE: 4N01.000, 4N01.001, 4N01.002, 4N01.003
49
Download from Www.Somanuals.com. All Manuals Search And Download.
17. Copyright notices
Copyright notices
© 2007 TomTom International B.V., The Netherlands.
Patents Pending. All rights reserved.
TomTom and the TomTom logo are registered trademarks of TomTom
International B.V., The Netherlands. All other trademarks are the property of
their respective owners.
Our end user license agreement and a limited warranty apply to this product;
they are included in this package. You can also review both at
Data Source
© 1984 – 2007 Tele Atlas North America. Inc. All rights reserved.
Canadian data © DMTI Spatial. Portions of Canadian map data are reproduced
under license from Her Majesty the Queen in Right of Canada with permission
from Natural Resource Canada. Point of Interest data by Info USA. Copyright
2007.
Some images are taken from NASA’s Earth Observatory.
The purpose of NASA’s Earth Observatory is to provide a freely-accessible
publication on the Internet where the public can obtain new satellite imagery
and scientific information about our home planet.
The focus is on Earth’s climate and environmental change:
earthobservatory.nasa.gov/
50
Download from Www.Somanuals.com. All Manuals Search And Download.
|