User’s Guide
2001
Mixed-Signal Products
SLOU105A
Download from Www.Somanuals.com. All Manuals Search And Download.
Preface
Read This First
How to Use This Manual
This document contains the following chapters:
Chapter 1—Introduction
Chapter 2—Quick Start
Information About Cautions and Warnings
This book may contain cautions and warnings.
This is an example of a caution statement.
A caution statement describes a situation that could potentially
damage your software or equipment.
This is an example of a warning statement.
A warning statement describes a situation that could potentially
cause harm to you.
The information in a caution or a warning is provided for your protection.
Please read each caution and warning carefully.
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
Running Title—Attribute Reference
Related Documentation From Texas Instruments
TI Plug-N-Play Audio Amplifier Evaluation Platform (literature
number SLOU011) provides detailed information on the evaluation
platform and its use with TI audio evaluation modules.
TPA6102A2 50-mW Stereo Audio Power Amplifier (literature
number SLOS324) This is the data sheet for the TPA6102A2 audio
amplifier integrated circuit.
FCC Warning
This equipment is intended for use in a laboratory test environment only. It
generates, uses, and can radiate radio frequency energy and has not been
tested for compliance with the limits of computing devices pursuant to subpart
J of part 15 of FCC rules, which are designed to provide reasonable protection
against radio frequency interference. Operation of this equipment in other
environments may cause interference with radio communications, in which
case the user at his own expense will be required to take whatever measures
may be required to correct this interference.
iv
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
1
2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
1.1
1.2
1.3
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
TPA6102A2 EVM Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Quick Start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
2.1
2.2
2.3
2.4
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
Quick Start List for Platform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
Quick Start List for Stand-Alone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5
2.4.1 TPA6102A2 Filterless Class-D EVM Schematic . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5
2.4.2 TPA6102A2 Audio Power Amplifier Evaluation Module Parts List . . . . . . . . . . 2-6
2.4.3 TPA6102A2 EVM PCB Layers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6
v
Download from Www.Somanuals.com. All Manuals Search And Download.
Figures
1–1
2–1
2–2
2–3
2–4
2–5
The TI TPA6102A2 Audio Amplifier Evaluation Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Quick Start Platform Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
Quick Start Module Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
TPA6102A2 Class-D EVM Schematic Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5
TPA6102A2 EVM Top Layer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6
TPA6102A2 EVM Bottom Layer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6
Tables
2–1
Typical TI Plug-N-Play Platform Jumper and Switch Settings for the
TPA6102A2 EVM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
TPA6102A2 EVM Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6
2–2
vi
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1
Introduction
This chapter provides an overview of the Texas Instruments (TI) TPA6102A2
audio amplifier evaluation module (SLOP337). It includes a list of EVM
features, a brief illustrated description of the module, and a list of EVM
specifications.
Topic
Page
1.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–2
1.2 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–3
1.3 TPA6102A2 EVM Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–3
1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Features
1.1 Features
The TI TPA6102A2 audio amplifier evaluation module and the TI plug-n-play
audio amplifier evaluation platform include the following features:
TPA6102A2 Stereo Audio Power Amplifier Evaluation Module
1.6-V to 3.6-V operation
Fixed-gain of 2 dB (inverting)
Dual channel, single-ended operation
50-mW output power into 16 Ω at 3.3 V
Verylowdistortion—THD+Nislessthan0.08%at1kHzandlessthan
0.2% from 20 Hz to 20 kHz into 16-Ω loads, and less than 0.06% at
1 kHz and less than 0.2% from 20 Hz to 20 kHz into 32-Ω loads
Extremely low current consumption in shutdown mode
Internal thermal and short-circuit protection
Internal pop reduction circuitry
Quick and Easy Configuration With the TI Plug-N-Play Audio Amplifier
Evaluation Platform
Evaluation module is designed to simply plug into the platform,
automatically making all signal, control, and power connections
Platform provides flexible power options
Jumpers on the platform select power and module control options
Switches on the platform route signals
Platform provides quick and easy audio input and output connections
Platform Power Options
Onboard 9-V battery
External 5-V – 15-V (V ) supply inputs
CC
External regulated V
supply input
DD
Socket for onboard 5-V V
voltage regulator EVM
DD
Onboard overvoltage and reverse polarity power protection
Platform Audio Input and Output Connections
Left and right RCA phono jack inputs
Miniature stereo phone jack input
Left and right RCA phono jack outputs
Left and right compression speaker terminal outputs
Miniature stereo headphone jack output
1-2
Introduction
Download from Www.Somanuals.com. All Manuals Search And Download.
Description
1.2 Description
The TPA6102A2 audio power amplifier evaluation module is a complete,
low-power stereo audio power amplifier for high-fidelity line-level output,
headphone, and small speaker applications. It consists of the TI TPA6102A2
50-mW stereo audio power amplifier IC in a very small MSOP package, along
with a small number of other parts mounted on a circuit board that is
approximately one and a quarter inches square (see Figure 1–1).
Figure 1–1. The TI TPA6102A2 Audio Amplifier Evaluation Module
†
Due to the very small size of the MSOP IC package, the standard part number TPA6102A2 is
replaced with the code TIAJN.
Single in-line header pins are mounted to the underside of the module circuit
board to allow the EVM to be plugged into the TI plug-n-play audio amplifier
evaluation platform, or to be wired directly into existing circuits and equipment
when used stand-alone.
The platform has room for a single TPA6102A2 evaluation module and is a
convenient vehicle for demonstrating TI’s audio power amplifier and related
evaluation modules. The EVMs simply plug into the platform, which
automatically provides power to the modules, interconnects them correctly,
andconnectsthemtoaversatilearrayofstandardaudioinputandoutputjacks
and connectors. Easy-to-use configuration controls allow the platform and
EVMs to quickly model many possible end-equipment configurations.
There is nothing to build, nothing to solder, and nothing but the speakers
included with the platform to hook up.
1.3 TPA6102A2 EVM Specifications
Supply voltage range, V
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.6 V to 3.6 V
DD
Supply current, I
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160 mA, max
DD
Continuous output power, P : 16 Ω, V
= 3.3 V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 mW
O
DD
Audio input voltage, V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . V
+ 0.3 Vpp, max
I
DD
Minimum load impedance, R . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Ω
L
1-3
Introduction
Download from Www.Somanuals.com. All Manuals Search And Download.
1-4
Introduction
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2
Quick Start
The steps in this chapter can be followed to prepare the TPA6102A2 audio
amplifier EVM for use. Using the TPA6102A2 EVM with the TI plug-n-play
audio amplifier evaluation platform is a quick and easy way to connect power,
signal and control inputs, and signal outputs to the EVM using standard
connectors. However, the audio amplifier evaluation module can be used
stand-alone by making connections directly to the module pins, and it can be
wired directly into existing circuits or equipment.
The platform switch and jumper settings shown in Table 2–1 are typical for the
TPA6102A2 EVM and will cause the TPA6102A2 IC to shutdown/mute when
a plug is removed from platform headphone jack J10.
Table 2–1. Typical TI Plug-N-Play Platform Jumper and Switch Settings for the
TPA6102A2 EVM
EVM
JP6
JP7
JP8
S2
S3
TPA6102A2
X
Lo
X
See Note 2
U5
Notes: 1) X = Don’t care
2) Set S2 to ON when signal conditioning board is installed in U1; set S2
to OFF when no signal conditioning board is installed.
Topic
Page
2.1 Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–2
2.2 Quick Start List for Platform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–3
2.3 Quick Start List for Stand-Alone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–4
2.4 Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–5
2-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Precautions
2.1 Precautions
Power Supply Input Polarity and Maximum Voltage
Always ensure that the polarity and voltage of the external power
connected to V
power input connector J1, J2, and/or V
power
CC
DD
input connector J6 are correct. Overvoltage or reverse-polarity
power applied to these terminals can open onboard soldered-in
fuses and cause other damage to the platform, installed evaluation
modules, and/or the power source.
Inserting or Removing EVM Boards
Do not insert or remove EVM boards with power applied: Damage
to the EVM board, the platform, or both may result.
Figure 2–1. Quick Start Platform Map
6b
1
10
6b
7b
ICC
JP4
C1+
F1
VR1
6a
DC
Power
In/Out
6b
Power
Input
R2
R1
Audio
Power
Amps
Signal Conditioning
8
Audio
Input
Speaker
Output
Mode
Mute
Polarity
Lo
****CAUTION****
Do not insert or remove
EVM boards with power
applied
Hi
Stereo
Headphone
Output
Plug-N-Play Audio Amplifier
Evaluation Platform
SLOP097 Rev. C.1
R3
R4
HP Out
9
R5
4
2
5
3
2-2
Quick Start
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Start List for Platform
2.2 Quick Start List for Platform
Follow these steps when using the TPA6102A2 EVM with the TI plug-n-play
audio amplifier evaluation platform (see the platform user’s guide, literature
number SLOU011, for additional details). Numbered callouts for selected
steps are shown in Figure 2–1.
Platform preparations
1) EnsurethatallexternalpowersourcesaresettoOFF andthattheplatform
power switch S1 is set to OFF.
2) Install a TPA6102A2 module in platform socket U5, taking care to align the
module pins correctly.
3) Use switch S2 to select or bypass the signal conditioning EVM (U1).
4) Set control signal polarity jumper JP7 to Lo.
5) Set Hp source switch S3 to U5 to route the output signal to the headphone
jack (J10).
Power supply
6) Select and connect the power supply:
7) Connect an external regulated power supply set to a voltage between 1.6
V and 3.6 V to platform V
serve marked polarity,
power input connector J6, taking care to ob-
DD
or
8) Install a 3-V to 5-V voltage regulator EVM (SLVP097 or equiv.) in platform
socket U6. Install a 9-V battery in B1 or connect a 7-V to 12-V power
source to a platform V
power input J1 or J2 and jumper the appropriate
CC
power input (see platform user’s guide). Set jumper JP1 on the SLVP097
to 3.3-V operation.
Inputs and outputs
9) Ensure that signal source level is set to minimum and that potentiometers
R1 and R4 are set to the midpoint.
10) Connect the audio source to left and right RCA phono jacks J3 and J5 or
stereo miniature phone jack J4.
11) Connect 16-Ω to 32-Ω headphones to headphone jack J10.
Power-up
12) Verify correct voltage and input polarity and set the external power supply
to ON. If V and an onboard regulator EVM are used to provide V , set
CC
DD
platform power switch S1 to ON.
Platform LED2 should light indicating the presence of V , and the evaluation
DD
modules installed on the platform should begin operation.
2-3
Quick Start
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Start List for Stand-Alone
2.3 Quick Start List for Stand-Alone
Follow these steps to use the TPA6102A2 EVM stand-alone or when connect-
ing it into existing circuits or equipment. Connections to the TPA6102A2 mod-
ule header pins can be made via individual sockets, wire-wrapping, or solder-
ing to the pins, either on the top or the bottom of the module circuit board.
Numbered callouts for selected steps are shown in Figure 2–2.
Figure 2–2. Quick Start Module Map
2
5
4
6
6
4
†
Due to the very small size of the MSOP IC package, the standard part number TPA6102A2 is
replaced with the code TIAJN.
Power supply
1) Ensure that all external power sources are set to OFF.
2) Connect an external regulated power supply set between 1.6 V and 3.3 V
to the module VDD and GND pins taking care to observe marked polarity.
Inputs and outputs
3) Ensure that signal source level is set to minimum.
4) Connect the audio source to the module IN1, IN2, and GND pins taking
care to observe marked polarity.
5) Connect the shutdown pin to V
through a normally open switch.
DD
6) Connect 32-Ω headphones to the module V 1 and V 2 pins through
O
O
33-µF to 1000-µF output-coupling capacitors (see Figure 3–8) and return
to the GND pin, or
7) For line output, connections to the V 1 and V 2 pins must be made
O
O
through 33-µF to 1000-µF output-coupling capacitors and returned to
GND.
Power-up
8) Verify correct voltage and input polarity and set the external power supply
to ON.
The EVM should begin operation.
2-4
Quick Start
Download from Www.Somanuals.com. All Manuals Search And Download.
TPA6102A2 EVM Schematic
2.4 Reference
2.4.1 TPA6102A2 EVM Schematic
The TPA6102A2 EVM schematic is shown in Figure 2–3.
Figure 2–3. TPA6102A2 EVM Schematic Diagram
C1
0.1 µF
RIN
8
7
1
BYPASS
IN1–
C3
1 µF
V
V
1
O
ROUT
2
GND
TPA6102A2
6
5
3
4
SHUTDOWN
V
DD
DD
C5
+
C4
0.1 µF
C2
10 µF
0.1 µF
LOUT
IN2–
V
O
2
LIN
R1
100 kΩ
S1
SHUTDOWN
2-5
Quick Start
Download from Www.Somanuals.com. All Manuals Search And Download.
TPA6102A2 Audio Power Amplifier Evaluation Module Parts List
2.4.2 TPA6102A2 Audio Power Amplifier Evaluation Module Parts List
Table 2–2.TPA6102A2 EVM Parts List
Manufacturer/
Part Number
Ref.
Description
Size
Qty.
Vendor/Number
Arrow
C1, C2,
C4
Capacitor, 0.1 µF, ±10%,
Nonpolarized, SMD
0603
1
Murata
GRM39X7R104K16
GRM39X7R104K16
C3
C5
R1
Capacitor, 1 µF, ±10%,
0603
A
1
1
4
1
Murata
GRM39Y5V105Z010
Arrow
GRM39Y5V105Z010
Nonpolarized, SMD
Capacitor, 10 µF, 6.3 V,
SMD
Panasonic
ECS–TOJY106R
Digi-Key
PCS1106CT-ND
Resistor, 100 kΩ, 1/16 W,
5%, SMD
0603
Panasonic
ERJ-3GSYJ104
Digi-Key
P100KGTR-ND
S1
Switch, momentary, SMD
Panasonic
Digi-Key
(SHUT-
DOWN)
EVQ–PJS04K
P8048SCT-ND
U1
IC, TPA6102A2DGK APA, MSOP-8
50 mW, 2 channel
1
TI
TPA6102A2DGK
PnP Pins Terminal post headers
11
Sullins
Digi-Key
S1022-36-ND
2.4.3 TPA6102A2 EVM PCB Layers
The following illustrations depict the TPA6102A2 PCB layers. These drawings
are not to scale. Gerber plots can be obtained from any TI sales office.
Figure 2–4. TPA6102A2 EVM Top Layer
Figure 2–5. TPA6102A2 EVM Bottom Layer
2-6
Quick Start
Download from Www.Somanuals.com. All Manuals Search And Download.
|