TAS5102EVM and TAS5103EVM for the
TAS5102 and TAS5103 Digital Amplifier Power
Output Stages
User's Guide
Literature Number: SLLU106
August 2008
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
1
2
Related Documentation from Texas Instruments...................................................................... 5
1.1
Additional Documentation................................................................................................ 5
Overview............................................................................................................................. 5
2.1
2.2
TAS5102EVM and TAS5103EVM Features........................................................................... 6
PCB Key Map.............................................................................................................. 6
3
Quick-Setup Guide ............................................................................................................... 7
3.1
3.2
3.3
3.4
3.5
Electrostatic Discharge Warning ........................................................................................ 7
Unpacking the EVM....................................................................................................... 7
Power Supply Setup ...................................................................................................... 7
GUI Software Installation................................................................................................. 8
Operational Sequence and Indicators.................................................................................. 9
4
System Interfaces ................................................................................................................ 9
4.1
4.2
4.3
4.4
4.5
4.6
Power Supply (PSU) Interface (PVDD and GND) .................................................................... 9
J1 Amplifier Connection to MC012 Controller Module.............................................................. 10
Loudspeaker Connectors (J3 - J6) .................................................................................... 10
SPDIF Optical Input Connector........................................................................................ 11
SPDIF Co-Axial Input Connector ...................................................................................... 11
USB Connector .......................................................................................................... 11
5
Protection.......................................................................................................................... 11
5.1
Short-Circuit Protection and Fault-Reporting Circuitry.............................................................. 11
Fault Reporting........................................................................................................... 11
5.2
Appendix A Design Documents ................................................................................................... 12
A.1
A.2
A.3
A.4
A.5
A.6
HPL-MC012 Schematic................................................................................................. 12
HPL-MC012 Composite Drawings .................................................................................... 14
TAS5102/3EVM Schematic ............................................................................................ 15
TAS5102/3EVM Composite Drawings ................................................................................ 16
Heat Sink Drawing....................................................................................................... 19
Parts List.................................................................................................................. 19
Important Notices............................................................................................................... 24
SLLU106–August 2008
Table of Contents
3
Submit Documentation Feedback
Download from Www.Somanuals.com. All Manuals Search And Download.
List of Figures
1
2
3
4
Physical Structure for TAS5102/3EVM ................................................................................... 6
Modulator and Power Stage Board Connection Example.............................................................. 7
TAS5086 GUI Window ...................................................................................................... 8
Recommended Power-Up Sequence.................................................................................... 10
List of Tables
1
Related Documentation From Texas Instruments....................................................................... 5
Recommended Supply Voltage ............................................................................................ 8
Recommended Supply Voltages........................................................................................... 9
J9/J10 Pin Description Amplifier/Controller Connector................................................................ 10
Output Pin Description..................................................................................................... 10
TAS5102 Warning/Error Signal Decoding .............................................................................. 11
Bill of Materials for HPL-MC012.......................................................................................... 19
Bill of Materials for TAS5103EVM ....................................................................................... 21
Bill of Materials for TAS5102EVM ....................................................................................... 22
2
3
4
5
6
A-1
A-2
A-3
4
List of Figures
SLLU106–August 2008
Submit Documentation Feedback
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Guide
SLLU106–August 2008
TAS5102EVM and TAS5103EVM for the TAS5102 and
TAS5103 Digital Amplifier Power Output Stages
This user's guide describes the operation of the TAS5102 and TAS5103 evaluation modules (EVM) from
Texas Instruments.
1
Related Documentation from Texas Instruments
Table 1 contains a list of data sheets that have detailed descriptions of the integrated circuits used in the
design of the HPL-MC012 Modulator/Controller Module which accompanies the TAS5102EVM and
TAS5103EVM as well as the link to the TAS5102/3 data sheet. These documents can be obtained from
Table 1. Related Documentation From Texas
Instruments
Part Number
TAS5086
Literature Number
SLES131
TAS5102/3
SLLS801
TUSB3210
SLLS466
UA78M12CKTPR
TPS40200D
SLVS059
SLUS659
TPS3825-33DBVT
SLVS165
1.1 Additional Documentation
•
Personal Computer (PC) Configuration Tool for TAS5086 (TAS5086 GUI version 4.0 or later). This
software comes on the compact disk in the EVM package.
2
Overview
The TAS5102EVM and TAS5103EVM packages are composed of two separate modules, the HPL-MC012
Modulator/Controller Module and the TAS5102EVM or TAS5103EVM Amplifier Module. They are
designed so that the user can separate the two modules and connect the TAS5102EVM or TAS5103EVM
Amplifier Module into a target system via a ribbon cable. Keep this ribbon cable as short as possible to
avoid degradation in the PWM signals.
The TAS5102 and TAS5103 customer evaluation amplifier modules each demonstrate two audio
integrated circuits — the TAS5086 and the TAS5102 or TAS5103 from Texas Instruments (TI).
The TAS5086DBT is a high-performance, 32-bit (24-bit input), multichannel PurePath Digital™ pulse width
modulator (PWM) based on Equibit™ technology with fully symmetrical AD modulation scheme. It accepts
an input sample rate from 32 kHz to 192 kHz. The device also has digital audio processing (DAP) that
provides bass management, advanced performance, and a high level of system integration.
The TAS5102 is a compact, high-power, digital amplifier power stage designed to drive an 8-Ω
loudspeaker up to 20 W/channel at 10% THD+N. It contains integrated gate-drive, four matched and
electrically isolated enhancement-mode N-channel power DMOS transistors, and protection/fault-reporting
circuitry. The DAD package has a PowerPAD™ package on the top side for heat transfer through a heat
sink. The heat sink in this design is for evaluation purposes only.
PurePath Digital, Equibit, PowerPAD are trademarks of Texas Instruments.
Windows is a trademark of Mircrosoft Corporation.
SLLU106–August 2008
TAS5102EVM and TAS5103EVM for the TAS5102 and TAS5103 Digital Amplifier Power Output Stages
5
Submit Documentation Feedback
Download from Www.Somanuals.com. All Manuals Search And Download.
Overview
The TAS5103 is a compact, high-power, digital amplifier power stage designed to drive an 8-Ω
loudspeaker up to 15 W/channel at 10% THD+N. It contains integrated gate-drive, four matched and
electrically isolated enhancement-mode N-channel power DMOS transistors, and protection/fault-reporting
circuitry. The DAP package has a PowerPAD™ package on the bottom side for heat transfer through the
printed-circuit board.
Either of these EVMs plus the HPLMC-012 form a complete two-channel, digital audio amplifier system
which includes digital input (S/PDIF), control interface (via USB) to PC and DAP (digital audio processor)
features like digital volume control, bass management, and input and output multiplexers.
This EVM is designed to illustrate a low-cost approach to an amplifier design using this device. Improved
performance, at increased cost, can be achieved with a high-performance configuration.
2.1 TAS5102EVM and TAS5103EVM Features
•
Modular approach comprised of TAS5102EVM or TAS5103EVM amplifier modules and HPL-MC012
modulator/controller module
•
•
•
•
•
Two-channel evaluation module.
Self-contained protection system (short-circuit and thermal).
Standard I2S and I2C control via SPDIF and USB
Double-sided, plated-through printed-circuit board (PCB) layout
Single power supply operation
2.2 PCB Key Map
Power
Supply
SPDIF Receiver
3.3V SMPS
TAS5102
USB Controller
TAS5086
Figure 1. Physical Structure for TAS5102/3EVM
6
TAS5102EVM and TAS5103EVM for the TAS5102 and TAS5103 Digital Amplifier Power Output Stages
SLLU106–August 2008
Submit Documentation Feedback
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick-Setup Guide
3
Quick-Setup Guide
This section describes the TAS5102/3EVM board in regards to power supplies and system interfaces. It
provides information regarding handling and unpacking, absolute operating conditions, and a description
of the factory default switch and jumper configuration.
The section also provides a step-by-step guide to configuring the TAS5102/3EVM for device evaluation.
3.1 Electrostatic Discharge Warning
Many components on the TAS5102/3EVM are susceptible to damage by electrostatic discharge (ESD).
Customers are advised to observe proper ESD handling precautions when unpacking and handling the
EVM, including the use of a grounded wrist strap at an approved ESD workstation.
CAUTION
Failure to observe ESD handling procedures can result in damage to EVM
components.
3.2 Unpacking the EVM
On opening the TAS5086-TAS5102EVM or TAS51033EVM package, ensure that the following items are
included:
•
•
•
•
1 pc. TAS5102/3 EVM Power Stage Board
1 pc. HPL-MC012 Modulator/Input Board
Because this system has standard connectors, no cables are supplied
1 pc. TAS5102/3EVM CD-ROM.
If any of these items are missing, contact the Texas Instruments Product Information Center nearest you
to inquire about a replacement.
Connect the Modulator/Input board to the Power Stage board with the docking connectors on each board.
Use care because this connector is not keyed.
Figure 2. Modulator and Power Stage Board Connection Example
3.3 Power Supply Setup
To power up the EVM, one power supply is needed for system power, logic and gate-drive, and for output
stage supply. The power supply is connected to the EVM with banana cables or stripped insulated wire.
SLLU106–August 2008
TAS5102EVM and TAS5103EVM for the TAS5102 and TAS5103 Digital Amplifier Power Output Stages
7
Submit Documentation Feedback
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick-Setup Guide
Table 2. Recommended Supply Voltage
Description
Output stage power supply
Voltage Limitations
Current Requirement
Connector
Red/black
8 V – 23 V
5 A
CAUTION
damage to your hardware.
3.4 GUI Software Installation
The TAS5086 GUI provides easy control of all registers in TAS5086. To install the GUI, run the setup file
from the TAS5102/3 CD-ROM.
After installation, turn on the power supply, and connect the USB cable to the Modulator/Controller board.
Start the GUI program from The Windows™ menu. (Program Files/Texas Instruments Inc) The start-up of
the GUI takes few seconds.
Figure 3. TAS5086 GUI Window
From the files menu, load the configuration file:
TAS5102 EVM Configuration.cfg
The file is located on the TAS5102/3EVM CD-ROM. This file contains all settings for a default setup of the
EVM.
For easy access of the file, it is recommended to copy the files into directory where the GUI is installed.
Default is C:\Program Files\Texas Instruments Inc\TAS5086\.
For more advanced use of the GUI and the features of the TAS5086 modulator, see the GUI User’s Guide
and the TAS5086 data sheet (SLES131). The GUI User's Guide can be accessed by clicking on Help in
the toolbar and then selecting User's Guide in the drop-down menu.
8
TAS5102EVM and TAS5103EVM for the TAS5102 and TAS5103 Digital Amplifier Power Output Stages
SLLU106–August 2008
Submit Documentation Feedback
Download from Www.Somanuals.com. All Manuals Search And Download.
System Interfaces
3.5 Operational Sequence and Indicators
•
After connecting the power supply and turning it on, the power supply current must be ~50 mA. The
amplifier reset LED must be on.
The PVDD and 3.3-V LEDs must be on. If not, check the connections to the power supply.
–
•
•
Connect the SPDIF cable, either optical or coaxial, to an SPDIF source.
Connect the USB cable and the USB LED (blue LED must be on).
–
The EVM must enumerate without the installation of a USB driver; it is a Windows™ audio class
device.
•
•
Start the GUI. (It must not give an indication of COMMUNICATION ERROR).
C:\Program Files\Texas Instruments Inc\TAS5086 GUI
Load the configuration file.
–
–
–
–
–
–
(File, Load, Config File, TAS5102 EVM Configuration.cfg)
The AMP RESET LED must go off.
The power supply current must be ~100 mA.
This indicates that the amplifier is switching and ready for audio input.
The SPDIF indicator must be on (blue LED), when locked to a valid source of SPDIF.
•
If the preceding conditions are met, the EVM system is ready to accept audio data.
–
Note: The default gain setting of the TAS5086 GUI is 0 dB. If you are connecting directly from a
music source (CD player) for input and speakers for output, you may want to use the volume
control function of GUI to reduce the gain before the program material is started.
4
System Interfaces
This section describes the TAS5102/3 EVM board in regards to power supplies and system interfaces.
4.1 Power Supply (PSU) Interface (PVDD and GND)
The TAS5102/3 EVM module must be powered from a well-regulated external power supply. Good audio
performance requires a stabilized power supply with low ripple voltage and low output impedance.
Note: The length of power supply cable must be minimized. Increasing the length of the PSU cable
is equal to increasing the distortion for the amplifier at high output levels and low
frequencies.
Maximum output stage supply voltage depends of the speaker load resistance. For the recommended
maximum supply voltage, see the TAS5102/3 data sheet (SLLS801).
Table 3. Recommended Supply Voltages
Voltage Limitations
Description
Current Recommendations
(8-Ω Load)
Output stage power supply
8 V – 23 V
5 A
SLLU106–August 2008
TAS5102EVM and TAS5103EVM for the TAS5102 and TAS5103 Digital Amplifier Power Output Stages
9
Submit Documentation Feedback
Download from Www.Somanuals.com. All Manuals Search And Download.
System Interfaces
operation, the RESET signal should be kept low during power up. RESET is pulled low during power up
for 200 ms by the onboard reset generator (U2).
System power supply
Output stage power supply
RESET
>1 ms
Figure 4. Recommended Power-Up Sequence
4.2 J1 Amplifier Connection to MC012 Controller Module
Table 4. J9/J10 Pin Description Amplifier/Controller Connector
Net-Name at
Schematics
Pin No.
Description
1, 2, 5, 6 ,10, 11, 28
DGND
Low-current ground for modulator/controller
3, 4
7
PVDD1
OTW
PVDD buffered through 24-Ω resistor to power the modulator/controller
Overtemperature warning from the amplifier (T > 125°C)
8, 9, 13, 15, 17, 19, 20, 21,
22, 23, 25, 27
NC
Not connected
12
14
16
18
24
26
PWM_A
PWM_B
PWM_C
PWM_D
RESET
FAULT
Channel A PWM signal from modulator
Channel B PWM signal from modulator
Channel C PWM signal from modulator
Channel D PWM signal from modulator
Resets the TAS5102/3
Power stage fault indicator
4.3 Loudspeaker Connectors (J3 - J6)
CAUTION
Both positive and negative speaker outputs are floating and may not be
connected to ground (e.g., through an oscilloscope).
Table 5. Output Pin Description
Net-Name at Schematics
Description
OUT_A
OUT_B
OUT_C
OUT_D
Speaker positive output
Speaker negative output
Speaker positive output
Speaker negative output
10
TAS5102EVM and TAS5103EVM for the TAS5102 and TAS5103 Digital Amplifier Power Output Stages
SLLU106–August 2008
Submit Documentation Feedback
Download from Www.Somanuals.com. All Manuals Search And Download.
Protection
4.4 SPDIF Optical Input Connector
This connector is a standard TOSLINK connector that connects the SPDIF digital audio input to the SPDIF
receiver on the HPL-MC012 PCB. This connector, or the SPDIF co-axial input, is used, but not both
connectors at the same time.
4.5 SPDIF Co-Axial Input Connector
This connector is a standard RCA connector that connects the SPDIF digital audio input to the SPDIF
receiver on the HPL-MC012 PCB. This connector, or the SPDIF optical Input, is used, but not both
connectors at the same time.
4.6 USB Connector
This connector is a standard USB connector and is used to connect GUI control information from a PC to
the HPL-MC012 PCB. The USB system does not stream audio from a PC.
5
Protection
This section describes the short-circuit protection and fault-reporting circuitry of the TAS5102/3 device.
5.1 Short-Circuit Protection and Fault-Reporting Circuitry
The TAS5102/3 is a self-protecting device that provides fault reporting (including high-temperature
protection and short-circuit protection). For highest possible reliability, recovering from a fault requires
external reset of the device. This is done by the TAS5086 on the HPL-MC012 board. See the TAS5102/3
data sheet for more information regarding the RESET function.
5.2 Fault Reporting
The OTW and FAULT outputs from TAS5102/3 indicate fault conditions. See the TAS5102/3 data sheet
(SLLS801) for a description of these pins.
Table 6. TAS5102 Warning/Error Signal Decoding
FAULT
OTW
Device Condition
Overcurrent (OC) or undervoltage (UVP) warning or overtemperature error
(OTE)
0
0
Overtemperature warning (OTW) or overcurrent (OC) or undervoltage
(UVP)
0
1
1
1
0
1
Junction temperature lower than 125°C and no faults (normal operation)
Junction temperature higher than 125°C (overtemperature warning)
The FAULT output is open-drain. The OTW output is push-pull active high.
The OTW LED on the MC012 is illuminated when the temperature of the TAS5102/3 is okay (less than
125°C.) The LED turns off when the TAS5102/3 is warning of overtemperature on the device (TJ > 125°C.)
This polarity is due to a reversal of polarity of the OTW pin from other devices (e.g., TAS5132) which also
use this modulator board.
SLLU106–August 2008
TAS5102EVM and TAS5103EVM for the TAS5102 and TAS5103 Digital Amplifier Power Output Stages
11
Submit Documentation Feedback
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A
Appendix A Design Documents
A.1 HPL-MC012 Schematic
12
Design Documents
SLLU106–August 2008
Submit Documentation Feedback
Download from Www.Somanuals.com. All Manuals Search And Download.
HPL-MC012 Schematic
SLLU106–August 2008
Design Documents
13
Submit Documentation Feedback
Download from Www.Somanuals.com. All Manuals Search And Download.
HPL-MC012 Composite Drawings
A.2 HPL-MC012 Composite Drawings
14
Design Documents
SLLU106–August 2008
Submit Documentation Feedback
Download from Www.Somanuals.com. All Manuals Search And Download.
TAS5102/3EVM Schematic
A.3 TAS5102/3EVM Schematic
SLLU106–August 2008
Design Documents
15
Submit Documentation Feedback
Download from Www.Somanuals.com. All Manuals Search And Download.
TAS5102/3EVM Composite Drawings
A.4 TAS5102/3EVM Composite Drawings
16
Design Documents
SLLU106–August 2008
Submit Documentation Feedback
Download from Www.Somanuals.com. All Manuals Search And Download.
TAS5102/3EVM Composite Drawings
SLLU106–August 2008
Design Documents
17
Submit Documentation Feedback
Download from Www.Somanuals.com. All Manuals Search And Download.
TAS5102/3EVM Composite Drawings
18
Design Documents
SLLU106–August 2008
Submit Documentation Feedback
Download from Www.Somanuals.com. All Manuals Search And Download.
Heat Sink Drawing
A.5 Heat Sink Drawing
A.6 Parts List
Table A-1. Bill of Materials for HPL-MC012
Description
RefDes
U4
QTY MFG
MFG Part#
PWM MODULATOR, 6 CH, TSSOP38-DBT
1
1
Texas Instruments
TAS5086DBT
USB, GENERAL PURPOSE DEVICE
CONTROLLER, LQFP64-PM
U3
Texas Instruments
TUSB3210PM
Single Inverter Gate, SOT23-DBV5
INV1, INV2
AND1
OR1
2
1
1
1
2
1
Texas Instruments
Texas Instruments
Texas Instruments
Texas Instruments
Texas Instruments
Texas Instruments
SN74AHC1GU04DBVR
SN74AHC1G08DBVR
SN74AHC1G32DBVR
SN74AHC1G86DBVR
TPS3825-33DBVT
TPS40200D
Single 2-Input Positive-AND Gate, SOT23-DBV5
Single 2-Input Positive-OR Gate, SOT23-DBV5
Single 2-Input Exclusive-OR Gate, SOT23-DBV5
Processor Supervisor Circuit, 3.3V
XOR1
U1, U2
U6
WIDE INPUT RANGE VOLTAGE MODE
CONTROLLER, SOP8-D
SPDIF RECEIVER, 192KHZ 6-1 SEL, SSOP30-DB
U5
1
AKM
AK4113VF/DIR9001
Semiconductor/Texa
s Instruments
OPTICAL RECEIVER, 3.3V, EDGE PCB-RA
Crystal, 12.000MHz, HC49US
OPTO1
Y1
1
1
1
1
Toshiba
ECS
TORX141P
ECS-120-32-4
ECS-122.8-S-4
24LC64-I/SM
Crystal, 12.288MHz, HC49US
Y2
ECS
EEPROM, SERIAL 64K 2.5V SOP8-PS
EPROM1
Microchip
Technology
PFET –3.0A –40V 0.1 OHM SOT23-DBV3
TRANSISTOR NPN, 40V 600mA, SOT-23
PFET1
Q1
1
1
3
Vishay Siliconix
Diodes, Inc.
Diodes Inc.
SI2319DS-T1
MMBT2222A-7
DDTA143TCA-7
Transistor PNP 50V PreBiased/4.7K 100mA
SOT23-DBV3
Q2, Q3, Q4
SCHOTTKY DIODE, 1A 40V, SMA
LED, BLUE SMD0603
CR1
1
2
2
ON SEMI
MBRA140T3
LED3, LED6
LED1, LED2
Lite-on Trading
Lumex Opto
LTST-C191TBKT
SML-LX1206SOC-TR
LED, Orange SM1206
SLLU106–August 2008
Design Documents
19
Submit Documentation Feedback
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts List
Table A-1. Bill of Materials for HPL-MC012 (continued)
Description
RefDes
LED5
QTY MFG
MFG Part#
LED, Red SM1206
1
1
1
2
2
1
1
1
2
1
2
Chicago Miniature
CMD15-21VRD/TR8
CMD15-21VYD/TR8
CMD15-21VGD/TR8
ECJ-1VC1H220J
ECU-V1H270JCV
ECU-V1H101JCV
ECU-V1H102KBV
ECJ-1VB1H332K
ECJ-1VB1E103K
ECJ-1VB1H223K
ECJ-1VB1C473K
ECJ-1VB1C104K
LED, Yellow SM1206
LED4
Chicago Miniature
Chicago Miniature
Panasonic
LED, Green SM1206
LED7
CAP 22PFD 50V CERM 0603 NPO
CAP 27PFD 50V CERM 0603 NPO
CAP 100PFD 50V CERM 0603 NPO
CAP 1000PFD 50V CERM 0603 X7R
CAP 3300PFD 50V CERM 0603 X7R
CAP .01UFD 25V CERM 0603 X7R
CAP .022UFD 50V CERM 0603 X7R
CAP .047UFD 16V CERM 0603 X7R
CAP 0.1UFD 16V CERM 0603 X7R
C1, C6
C18, C19
C12
Panasonic
Panasonic
C40
Panasonic
C11
Panasonic
C2, C3
C13
Panasonic
Panasonic
C23, C26
Panasonic
C4, C5, C7, C8, C20,
C21, C25, C27–C30
Panasonic
C32, C33, C36, C38,
C42–C45,
19
Panasonic
ECJ-1VB1C104K
CAP CERAMIC 100PFD 100V 5% RADIAL COG
C10
C15
1
1
EPCOS
EPCOS
B37979N1101J054
B37979N5471J054
CAP 470PFD 50V 5% MULTILAYER CERAMIC
COG
CAP 0.1UFD 50V CERM 0805 X7R
CAP 0.47UFD 35V CERM 0805 X5R
CAP 3.3UFD 50V CERM 1210 X7R
CAP 10UFD 16V ALUM ELEC SMD VSA
CAP 10UFD 16V RAD ALUM ELEC KGA
C16
C14
C9
1
1
1
1
7
Panasonic
Taiyo Yuden
TDK Corp.
Panasonic
Panasonic
ECJ-2YB1H104K
GMK212BJ474KG-T
C3225X7R1H335M
ECE-V1CS100SR
ECE-A1CKG100
C35
C22, C24, C31, C34,
C37, C41, C46
CAP 56UFD 50V RAD ALUM ELEC FC
CAP 560UFD 35V RAD ALUM ELEC FC
RES 22.1 OHM 1/16W 1% SMD 0603
RES 33 OHM 1/10W 5% SMD 0603
RES 47 OHM 1/16W 5% SMD 0603
C17
1
1
Panasonic
Panasonic
Panasonic
YAGEO
EEU-FC1H560
C39
EEU-FC1V561
R69, R74, R75, R76
R14, R15, R34, R36
4
ERJ-3EKF22R1V
9C06031A33R0JLHFT
9C06031A47R0JLHFT
4
R5, R6, R9, R10, R12,
R27–R29, R33, R54,
R58
11
YAGEO
RES 75.0 OHM 1/16W 1% SMD 0603
RES 100 OHM 1/16W 5% SMD 0603
RES 200 OHM 1/16W 1% SMD 0603
RES 332 OHM 1/16W 1% SMD 0603
RES 357 OHM 1/16W 1% SMD 0603
RES 1.50K OHM 1/16W 1% SMD 0603
RES 2.00K OHM 1/16W 1% SMD 0603
RES 4.99K OHM 1/16W 1% SMD 0603
RES 7.50K OHM 1/16W 1% SMD 0603
RES 10K OHM 1/16W 5% SMD 0603
R35
1
3
Panasonic
YAGEO
ERJ-3EKF75R0V
9C06031A1000JLHFT
ERJ-3EKF2000V
ERJ-3EKF3320V
ERJ-3EKF3570V
ERJ-3EKF1501V
ERJ-3EKF2001V
ERJ-3EKF4991V
ERJ-3EKF7501V
9C06031A1002JLHFT
R44, R45, R65
R7, R8, R31
R51, R52, R64, R56
R1, R3
3
Panasonic
Panasonic
Panasonic
Panasonic
Panasonic
Panasonic
Panasonic
Panasonic
4
2
R22, R24, R32
R67
3
1
R2, R4
2
R73
1
R17–R19, R21, R37,
R13, R47, R49, R62,
R63, R68, R72
12
RES 15.0K OHM 1/16W 1% SMD 0603
RES 18.2K OHM 1/10W 1% SMD 0603
RES 30.1K OHM 1/16W 1% SMD 0603
RES 100K OHM 1/16W 5% SMD 0603
R30, R71
R16
2
1
1
5
Panasonic
Yageo
ERJ-3EKF1502V
9C06031A1822FKHFT
ERJ-3EKF3012V
R43
Panasonic
Yageo
R20, R23, R25, R26,
R48
9C06031A1003JLHFT
RES 120K OHM 1/16W 5% SMD 0603
RES 1.00M OHM 1/16W 1% SMD 0603
R50
1
2
Yageo
9C06031A1203JLHFT
ERJ-3EKF1004V
R11, R66
Panasonic
20
Design Documents
SLLU106–August 2008
Submit Documentation Feedback
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts List
Table A-1. Bill of Materials for HPL-MC012 (continued)
Description
RefDes
R38
QTY MFG
Vishay/Dale
MFG Part#
RES 0.05 OHM 1/4W 1% SMD 0805
RES 2.7 OHM 1/10W 5% SMD 0805
RES 3.3 OHM 1/10W 5% SMD 0805
RES 49.9 OHM 1/10W 1% SMD 0805
RES 1.00K OHM 1/10W 1% SMD 0805
RES 37.4K OHM 1/10W 1% SMD 0805
RES 0.0 OHM 1/8W 5% SMD 1206
RES 1.0 OHM 1/8W 5% SMD 1206
RES 3.3 OHM 1/8W 5% SMD 1206
RES 4.7 OHM 1/8W 5% SMD 1206
Ferrite Bead, 11 Ohms 1.5A SM0805
Ferrite Bead, 39 Ohms 4A SM0805
INDUCTOR, 330UH, SMD-DR74
JACK, RCA, PCB-RA, ECONO ALL-METAL
Jack, USB PCB-Right Angle
1
2
3
1
1
1
1
1
1
1
1
1
1
1
1
1
1
WSL0805R0500FEA18
ERJ-6RQJ2R7V
ERJ-6RQJ3R3V
ERJ-6ENF49R9V
ERJ-6ENF1001V
ERJ-6ENF3742V
ERJ-8GEY0R00V
ERJ-8GEYJ1R0V
ERJ-8RQJ3R3V
ERJ-8RQJ4R7V
MI0805K110R-00
EXC-ML20A390U
DR74-331
R55, R61
R39, R42, R70
R41
Panasonic
Panasonic
Panasonic
Panasonic
Panasonic
Panasonic
Panasonic
Panasonic
Panasonic
Steward
R40
R46
R53
R57
R60
R59
FB1
FB2
Panasonic
Coiltronics
CUI Stack
Assmann
Sullins
L1
J2
RCJ-017
J1
AU-Y1007
Header, 2 Pin Male, Straight, Gold
JP1
PZC02SAAN
SOCKET HEADER, 2x14 PIN FEMALE GOLD
PCB-RA
J3
Samtec
SSW-114-02-G-D-RA
Switch, Momentary SMT-Short, Black Tab, 160g
PC Testpoint, Orange
S1, S2
2
4
Panasonic
EVQ-PPBA25
5003
BCK, CKOUT, DATA,
LRCK
Keystone
Electronics
BUS WIRE GROUND LOOP, 25MM LENGTH, 18
AWG
GND
1
4
Belden CDT
8019000100
8409
Standoff 4-40 Threaded M/F 1.50 in. ALUM-HEX
HW1, HW2, HW3, HW4
Keystone
Electronics
LockWasher, #4 Internal-Tooth, Zinc/Steel
Hex Nut, 4-40, Zinc/Steel
HW1, HW2, HW3, HW4
HW1, HW2, HW3, HW4
4
4
Building Fasteners
Building Fasteners
INT LWZ 004
HNZ440
Table A-2. Bill of Materials for TAS5103EVM
Description
RefDes
PA1
QTY
MFG
MFG Part#
15W DIG AMP PWR STAGE HTSSOP32-DAP
LED, GREEN 2.0V SMD0805
1
2
1
Texas Instruments TAS5103DAP
LED1, LED2
VR1
Lumex Optical
SML-LXT0805GW-TR
VOLTAGE REGULATOR, 3.3V 500mA
SOT223-DCY
Texas Instruments UA78M33CDCYR
CAP 2200PFD 50V CERM 0603 X7R
CAP 0.01UFD 50V CERM 0603 X7R
CAP 0.033UFD 50V CERM 0603 X7R
CAP 0.1UFD 16V CERM 0603 X7R
CAP 0.1UFD 50V CERM 0603 X7R
C12
1
5
4
1
5
Panasonic
Panasonic
Panasonic
Panasonic
Murata
ECJ-1VB1H222K
C11, C15, C26, C31, C34
C7, C19, C23, C35
C8
ECU-V1H103KBV
ECJ-1VB1H333K
ECJ-1VB1C104K
C1, C4, C16, C20, C32,
C39, C40
GRM188R71H104KA93D
CAP 1.0UFD 16V CERM 0603 X5R
CAP 1.0UFD 50V CERM 0603 X5S
CAP 0.1UFD 50V CERM 0805 X7R
CAP 0.1UFD 50V CERM 1206 X7R
CAP 1.0UFD 50V CERM 1206 X7R
C3, C36
2
2
4
2
2
2
Panasonic
Taiyo Yuden
Panasonic
Panasonic
TDK Corp.
EPCOS
ECJ-1VB1C105K
UMK107C105KA-T
ECJ-2YB1H104K
ECJ-3VB1H104K
C3216X7R1H105K
B32529C5474J
C5, C33
C10, C14, C25, C30
C16, C20
C17, C21
CAP 0.47UFD 50V METAL POLYESTER FILM
MKT
C27, C28
CAP 1.0UFD 50V METAL POLYESTER FILM
MKT
C9, C13, C24, C29
C37
4
1
EPCOS
B32529C5105J
EEU-FC1V330
CAP 33UFD 35V RAD ALUM ELEC FC
Panasonic
SLLU106–August 2008
Design Documents
21
Submit Documentation Feedback
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts List
Table A-2. Bill of Materials for TAS5103EVM (continued)
Description
RefDes
QTY
MFG
MFG Part#
EEU-FC1C470
CAP 47UFD 16V RAD ALUM ELEC FC
C38
1
3
Panasonic
Panasonic
CAP 220UFD 35V ALUM ELEC M-SERIES
ROHS
C2, C18, C22
ECA-1VM221BJ
CAP 330UFD 35V ALUM ELEC M-SERIES
ROHS
C6
1
Panasonic
ECA-1VM331B
RES 3.3 OHM 1/16W 5% SMD 0603
RES 357 OHM 1/16W 1% SMD 0603
RES 1.8K OHM 1/16W 5% SMD 0603
RES 22.1K OHM 1/16W 1% SMD 0603
RES 1.0 OHM 1/4W 5% SMD 1206
RES 10 OHM 1/4W 5% SMD 1206
RES 24 OHM 1/2W 5% SMD 1210
INDUCTOR, SERIES 11RHBP, 10UH
R4, R5, R6, R7
4
1
1
1
1
1
1
4
2
Yageo
9C06031A3R30JLHFT
ERJ-3EKF3570V
9C06031A1801JLHFT
ERJ-3EKF2212V
9C12063A1R00JLHFT
9C12063A10R0JLHFT
ERJ-P14J240U
R10
Panasonic
Yageo
R8
R3
Panasonic
Yageo
R9
R2
Yageo
R1
Panasonic
Toko America
Sullins
L1, L2, L3, L4
A7503AY-100M
HEADER, 2 PIN MALE, PCB, STRAIGHT GOLD JP1, JP3
ROHS
PBC02SAAN
HEADER, 3 PIN MALE, PCB, STRAIGHT GOLD JP2, M1, M2
ROHS
3
Sullins
Sullins
PBC03SAAN
HEADER, 2x14 PIN MALE GOLD PCB-RA
BINDING POST, 15A, UNINSULATED
J1
1
4
PZC14DBAN
111-2223-001
OUTA, OUTB, OUTC,
OUTD
Johnson
Components
BINDING POST, BLACK, 15A ECONO
BINDING POST, RED, 15A ECONO
GND
1
1
Keystone
Electronics
7007
PVDD
Keystone
7006
Electronics
SHUNT, BLACK AU FLASH 0.100
Hex Nut, 4-40, Zinc/Steel
JP1, JP2, JP3, M1, M2
HW1, HW2, HW3, HW4
5
4
4
SULLINS
SPC02SYAN
Building Fasteners HNZ440
Standoff 4-40 Threaded M/F 0.75 in. ALUM-HEX HW1, HW2, HW3, HW4
Keystone
8403
Electronics
Table A-3. Bill of Materials for TAS5102EVM
Description
RefDes
QTY
MFG
MFG Part#
20W STEREO DIG AMP PWR STAGE
HTSSOP32-DAD
PA1
1
Texas Instruments TAS5102DAD
VOLTAGE REGULATOR, 3.3V 500mA SOT223-DCY VR1
1
2
1
5
Texas Instruments UA78M33CDCYR
LED, GREEN 2.0V SMD0805
LED1, LED2
Lumex Optical
Panasonic
SML-LXT0805GW-TR
ECJ-1VB1H222K
CAP 2200PFD 50V CERM 0603 X7R
CAP 0.01UFD 50V CERM 0603 X7R
C12
C11, C15, C26, C31,
C34
Panasonic
ECU-V1H103KBV
CAP 0.033UFD 50V CERM 0603 X7R
CAP 0.1UFD 16V CERM 0603 X7R
CAP 0.1UFD 50V CERM 0603 X7R
C7, C19, C23, C35
C8
4
1
7
Panasonic
Panasonic
Murata
ECJ-1VB1H333K
ECJ-1VB1C104K
C1, C4, C16, C20,
C32, C40, C42
GRM188R71H104KA93D
CAP 1.0UFD 16V CERM 0603 X5R
C3, C36
2
4
4
2
4
1
1
3
1
Panasonic
Taiyo Yuden
Panasonic
EPCOS
ECJ-1VB1C105K
UMK107C105KA-T
ECJ-2YB1H104K
B32529C5474J
B32529C5105J
EEU-FC1V330
EEU-FC1C470
ECA-1VM221BJ
ECA-1VM331B
CAP 1.0UFD 50V CERM 0603 X5S
C5, C17, C21, C33
C10, C14, C25, C30
C27, C28
CAP 0.1UFD 50V CERM 0805 X7R
CAP 0.47UFD 50V METAL POLYESTER FILM MKT
CAP 1.0UFD 50V METAL POLYESTER FILM MKT
CAP 33UFD 35V RAD ALUM ELEC FC
CAP 47UFD 16V RAD ALUM ELEC FC
CAP 220UFD 35V ALUM ELEC M-SERIES ROHS
CAP 330UFD 35V ALUM ELEC M-SERIES ROHS
C9, C13, C24, C29
C37
EPCOS
Panasonic
Panasonic
Panasonic
Panasonic
C41
C2, C18, C22
C6
22
Design Documents
SLLU106–August 2008
Submit Documentation Feedback
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts List
Table A-3. Bill of Materials for TAS5102EVM (continued)
Description
RefDes
QTY
4
MFG
MFG Part#
RES 3.3 OHM 1/16W 5% SMD 0603
RES 357 OHM 1/16W 1% SMD 0603
RES 1.8K OHM 1/16W 5% SMD 0603
RES 22.1K OHM 1/16W 1% SMD 0603
RES 1.0 OHM 1/4W 5% SMD 1206
RES 10 OHM 1/4W 5% SMD 1206
RES 24 OHM 1/2W 5% SMD 1210
INDUCTOR, SERIES 11RHBP, 10UH
R4, R5, R6, R7
Yageo
9C06031A3R30JLHFT
ERJ-3EKF3570V
9C06031A1801JLHFT
ERJ-3EKF2212V
9C12063A1R00JLHFT
9C12063A10R0JLHFT
ERJ-P14J240U
R10
1
Panasonic
Yageo
R8
1
R3
1
Panasonic
Yageo
R9
1
R2
1
Yageo
R1
1
Panasonic
Toko America
Sullins
L1, L2, L3, L4
JP1, JP3
4
A7503AY-100M
HEADER, 2 PIN MALE, PCB, STRAIGHT GOLD
ROHS
2
PBC02SAAN
HEADER, 3 PIN MALE, PCB, STRAIGHT GOLD
ROHS
JP2, M1, M2
3
Sullins
PBC03SAAN
HEADER, 2x14 PIN MALE GOLD PCB-RA
BINDING POST, 15A, UNINSULATED
J1
1
4
Sullins
PZC14DBAN
111-2223-001
OUTA, OUTB, OUTC,
OUTD
Johnson
Components
BINDING POST, BLACK, 15A ECONO
BINDING POST, RED, 15A ECONO
SHUNT, BLACK AU FLASH 0.100
Standoff 4-40 Threaded M/F 1.50 in. ALUM-HEX
Hex Nut, 4-40, Zinc/Steel
GND
1
1
5
4
4
Keystone
Electronics
7007
PVDD
Keystone
Electronics
7006
JP1, JP2(2-3), JP3,
M1(2-3), M2(2-3)
Sullins
SPC02SYAN
8409
HW1, HW2, HW3,
HW4
Keystone
Electronics
HW1, HW2, HW3,
HW4
Building Fasteners HNZ440
SLLU106–August 2008
Design Documents
23
Submit Documentation Feedback
Download from Www.Somanuals.com. All Manuals Search And Download.
EVALUATION BOARD/KIT IMPORTANT NOTICE
Texas Instruments (TI) provides the enclosed product(s) under the following conditions:
This evaluation board/kit is intended for use for ENGINEERING DEVELOPMENT, DEMONSTRATION, OR EVALUATION PURPOSES
ONLY and is not considered by TI to be a finished end-product fit for general consumer use. Persons handling the product(s) must have
electronics training and observe good engineering practice standards. As such, the goods being provided are not intended to be complete
in terms of required design-, marketing-, and/or manufacturing-related protective considerations, including product safety and environmental
measures typically found in end products that incorporate such semiconductor components or circuit boards. This evaluation board/kit does
not fall within the scope of the European Union directives regarding electromagnetic compatibility, restricted substances (RoHS), recycling
(WEEE), FCC, CE or UL, and therefore may not meet the technical requirements of these directives or other related directives.
Should this evaluation board/kit not meet the specifications indicated in the User’s Guide, the board/kit may be returned within 30 days from
the date of delivery for a full refund. THE FOREGOING WARRANTY IS THE EXCLUSIVE WARRANTY MADE BY SELLER TO BUYER
AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED, IMPLIED, OR STATUTORY, INCLUDING ANY WARRANTY OF
MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE.
The user assumes all responsibility and liability for proper and safe handling of the goods. Further, the user indemnifies TI from all claims
arising from the handling or use of the goods. Due to the open construction of the product, it is the user’s responsibility to take any and all
appropriate precautions with regard to electrostatic discharge.
EXCEPT TO THE EXTENT OF THE INDEMNITY SET FORTH ABOVE, NEITHER PARTY SHALL BE LIABLE TO THE OTHER FOR ANY
INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES.
TI currently deals with a variety of customers for products, and therefore our arrangement with the user is not exclusive.
TI assumes no liability for applications assistance, customer product design, software performance, or infringement of patents or
services described herein.
Please read the User’s Guide and, specifically, the Warnings and Restrictions notice in the User’s Guide prior to handling the product. This
notice contains important safety information about temperatures and voltages. For additional information on TI’s environmental and/or
No license is granted under any patent right or other intellectual property right of TI covering or relating to any machine, process, or
combination in which such TI products or services might be or are used.
FCC Warning
This evaluation board/kit is intended for use for ENGINEERING DEVELOPMENT, DEMONSTRATION, OR EVALUATION PURPOSES
ONLY and is not considered by TI to be a finished end-product fit for general consumer use. It generates, uses, and can radiate radio
frequency energy and has not been tested for compliance with the limits of computing devices pursuant to part 15 of FCC rules, which are
designed to provide reasonable protection against radio frequency interference. Operation of this equipment in other environments may
cause interference with radio communications, in which case the user at his own expense will be required to take whatever measures may
be required to correct this interference.
EVM WARNINGS AND RESTRICTIONS
It is important to operate this EVM within the input voltage range of 12 V to 18 V and the output voltage range of 12 V to 18 V.
Exceeding the specified input range may cause unexpected operation and/or irreversible damage to the EVM. If there are questions
concerning the input range, please contact a TI field representative prior to connecting the input power.
Applying loads outside of the specified output range may result in unintended operation and/or possible permanent damage to the EVM.
Please consult the EVM User's Guide prior to connecting any load to the EVM output. If there is uncertainty as to the load specification,
please contact a TI field representative.
During normal operation, some circuit components may have case temperatures greater than 80° C. The EVM is designed to operate
properly with certain components above 100° C as long as the input and output ranges are maintained. These components include but are
not limited to linear regulators, switching transistors, pass transistors, and current sense resistors. These types of devices can be identified
using the EVM schematic located in the EVM User's Guide. When placing measurement probes near these devices during operation,
please be aware that these devices may be very warm to the touch.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyrigh© 2008, Texas Instruments Incorporated
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Applications
Audio
Automotive
Broadband
Digital Control
Medical
Amplifiers
Data Converters
DSP
Clocks and Timers
Interface
amplifier.ti.com
dataconverter.ti.com
dsp.ti.com
interface.ti.com
logic.ti.com
Logic
Military
Power Mgmt
Microcontrollers
RFID
power.ti.com
microcontroller.ti.com
Optical Networking
Security
Telephony
Video & Imaging
Wireless
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2008, Texas Instruments Incorporated
Download from Www.Somanuals.com. All Manuals Search And Download.
|