User's Guide
SLOU244–December 2009
TPA2011D1 Audio Power Amplifier Evaluation Module
The TPA2011D1 audio power amplifier evaluation module is a complete, low-power, Class-D, mono audio
power amplifier capable of delivering 1.47 W into 8 Ω and 2.57 W into 4 ohms at 1% THD+N (YFF
package). All components and the evaluation module are Pb-free. The TPA2011D1 evaluation module
(EVM) consists of a TPA2011D1 device and all necessary components to evaluate it.
Contents
1
2
3
4
Introduction .................................................................................................................. 1
Operation ..................................................................................................................... 1
Reference .................................................................................................................... 3
Related Documentation From Texas Instruments ...................................................................... 5
List of Figures
1
2
3
Top Layer ....................................................................................................................
Bottom Layer ................................................................................................................
TPA2011D1EVM Schematic Diagram....................................................................................
List of Tables
1
TPA2011D1EVM Parts List................................................................................................
1
Introduction
This section provides an overview of the Texas Instruments (TI) TPA2011D1 NanoFree™ WCSP audio
amplifier evaluation module (TPA2011D1EVM). It includes a brief description of the module and a list of
EVM specifications.
1.1 TPA2011D1EVM Specifications
Supply voltage range, VDD
2.5 V to 5.5 V
2.5 A
Power supply current rating required
Continuous output power, PO: 4-Ω BTL, VDD = 5 V, THD+N = 10%
Audio input voltage, VI
3.24 W
0 V to VDD
4 Ω
Minimum load impedance, ZL
2
Operation
This section describes how to operate the TPA2011D1EVM.
2.1 Quick Start for Stand-Alone Operation
Use the following steps when operating the TPA2011D1EVM stand-alone or when connecting the EVM
into existing circuits or equipment.
NanoFree is a trademark of Texas Instruments.
1
SLOU244–December 2009
TPA2011D1 Audio Power Amplifier Evaluation Module
Copyright © 2009, Texas Instruments Incorporated
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference
3
Reference
This section includes the EVM PCB layout reference, schematic, and parts list.
3.1 TPA2011D1EVM PCB Layers
DB
Figure 1. Top Layer
DB
Figure 2. Bottom Layer
3
SLOU244–December 2009
TPA2011D1 Audio Power Amplifier Evaluation Module
Copyright © 2009, Texas Instruments Incorporated
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference
3.2 TPA2011D1EVM Schematic Diagram
Vdd
VDD
C3
10ufd/6.3V
GND
R4
Vdd
TP OUT-
1.0K
GND
C9
4700pfd/50V
C4
0.1ufd/16V
U1
C1
R2
C10
150K
GND
0.1ufd/25V
4700pfd/50V
R5
C2
TP OUT+
R3
1.0K
IN
150K
0.1ufd/25V
JP1
TPA2011D1YFF
GND
Vdd
GND
FB1
R100
OUT +
OUT -
220ohms/2A
R1
0.0
100K
S1
FB2
R101
220ohms/2A
0.0
GND
C7
C8
TVS1
DNP
TVS2
DNP
1000pfd/100V 1000pfd/100V
GND
GND
GND
GND
TOP VIEW
A1 A2 A3
B1 B2 B3
C1 C2 C3
STANDOFFS
0.5in
0.5in
0.5in
0.5in
GND GND GND GND
0.5in 0.5in 0.5in 0.5in
Figure 3. TPA2011D1EVM Schematic Diagram
4
TPA2011D1 Audio Power Amplifier Evaluation Module
SLOU244–December 2009
Copyright © 2009, Texas Instruments Incorporated
Download from Www.Somanuals.com. All Manuals Search And Download.
Related Documentation From Texas Instruments
3.3 TPA2011D1 Audio Power Amplifier Evaluation Module Parts List
Table 1. TPA2011D1EVM Parts List
Part No.
U1
Description
Size
Qty.
Vendor Part Number
2.75W STEREO CLASS D AMP WCSP9-YFF
ROHS
1
Texas Instruments , TPA2011D1YFF
TVS1,
TVS2
TRANSIENT VOLTAGE SUPPRESSION BIDIR 6.1V
9A SOD-882 ROHS
2
2
2
2
1
1
ST Microelectronics, ESDALC6V1-1BT2
Panasonic, PCC1952CT
AVX, 478-1244-1
C7, C8
C1, C2
C9, C10
C3
CAP SMD0603 CERM 1000PFD 100V 10% X7R
ROHS
0603
0603
0805
0603
0402
CAP SMD0603 CERM 0.1UFD 25V 10% X5R
ROHS
CAP SMD0805 CERM 4700PFD 50V 5% X7R
ROHS
AVX, 478-3770-1
CAP SMD0603 CERM 10UFD 6.3V 20% X5R
ROHS
Panasonic, PCC2395CT
Taiyo Yuden, 490-3261-1
C4
CAP SMD0402 CERM 0.1UFD 16V 10% X7R
ROHS
R2, R3
R1
RES SMD0603 5% 1/10W 150K ROHS
RES 100K OHM 1/16W 1% SMD 0603 ROHS
RES SMT0805 1.0K 5% 1/8W ROHS
0603
0603
0805
0603
2
1
2
2
Panasonic, P150KGCT
Panasonic, P100KHCT
Panasonic, P1.0KACT
Panasonic, P0.0GCT
R4,R5
R100,
R101
RES 0.0 OHM 1/16W 5% SMD 0603 ROHS
FB1,FB2
FERRITE CHIP, 220 OHMS 2A 100MHZ SMD 0603
ROHS
0603
2
1
TDK, 445-1565-1
JP1
HEADER 2 PIN MALE, PCB STRAIGHT GOLD
ROHS
Sullins, S1011E-02 2
IN
JACK, RCA 3-PIN PCB-RA BLACK ROHS
PC TESTPOINT, RED, ROHS
1
1
1
1
1
4
Switchcraft, 65K7770
TP OUT+
TP OUT-
S1
Keystone Electronics, 5000K
Keystone Electronics, 5001K
E-Switch, EG4344CT
PC TESTPOINT, BLACK, ROHS
SWITCH, MOM, 160G SMT 4X3MM ROHS
SHUNT, BLACK AU FLASH 2mmLS
JP1
Norcomp Inc., SP2-001E
Emerson NPCS, J587
GND,VDD, BINDING-POST,NONINS,THRU,ROHS
OUT
+,OUT -
HW1,HW2, STANDOF ,4-40 0.5IN 3/16IN DIA ALUM RND F-F
HW3,HW4
4
4
Keystone, 2027K
HW1,HW2, 4-40 SCREW, STEEL 0.250 IN
HW3,HW4
Building Fasteners, H34
4
Related Documentation From Texas Instruments
•
TPA2011D1 Datasheet: 3.2W Mono Filter-Free Class-D Audio Power Amplifier with Auto-Recovering
5
SLOU244–December 2009
TPA2011D1 Audio Power Amplifier Evaluation Module
Copyright © 2009, Texas Instruments Incorporated
Download from Www.Somanuals.com. All Manuals Search And Download.
EVALUATION BOARD/KIT IMPORTANT NOTICE
Texas Instruments (TI) provides the enclosed product(s) under the following conditions:
This evaluation board/kit is intended for use for ENGINEERING DEVELOPMENT, DEMONSTRATION, OR EVALUATION PURPOSES
ONLY and is not considered by TI to be a finished end-product fit for general consumer use. Persons handling the product(s) must have
electronics training and observe good engineering practice standards. As such, the goods being provided are not intended to be complete
in terms of required design-, marketing-, and/or manufacturing-related protective considerations, including product safety and environmental
measures typically found in end products that incorporate such semiconductor components or circuit boards. This evaluation board/kit does
not fall within the scope of the European Union directives regarding electromagnetic compatibility, restricted substances (RoHS), recycling
(WEEE), FCC, CE or UL, and therefore may not meet the technical requirements of these directives or other related directives.
Should this evaluation board/kit not meet the specifications indicated in the User’s Guide, the board/kit may be returned within 30 days from
the date of delivery for a full refund. THE FOREGOING WARRANTY IS THE EXCLUSIVE WARRANTY MADE BY SELLER TO BUYER
AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED, IMPLIED, OR STATUTORY, INCLUDING ANY WARRANTY OF
MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE.
The user assumes all responsibility and liability for proper and safe handling of the goods. Further, the user indemnifies TI from all claims
arising from the handling or use of the goods. Due to the open construction of the product, it is the user’s responsibility to take any and all
appropriate precautions with regard to electrostatic discharge.
EXCEPT TO THE EXTENT OF THE INDEMNITY SET FORTH ABOVE, NEITHER PARTY SHALL BE LIABLE TO THE OTHER FOR ANY
INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES.
TI currently deals with a variety of customers for products, and therefore our arrangement with the user is not exclusive.
TI assumes no liability for applications assistance, customer product design, software performance, or infringement of patents or
services described herein.
Please read the User’s Guide and, specifically, the Warnings and Restrictions notice in the User’s Guide prior to handling the product. This
notice contains important safety information about temperatures and voltages. For additional information on TI’s environmental and/or
No license is granted under any patent right or other intellectual property right of TI covering or relating to any machine, process, or
combination in which such TI products or services might be or are used.
FCC Warning
This evaluation board/kit is intended for use for ENGINEERING DEVELOPMENT, DEMONSTRATION, OR EVALUATION PURPOSES
ONLY and is not considered by TI to be a finished end-product fit for general consumer use. It generates, uses, and can radiate radio
frequency energy and has not been tested for compliance with the limits of computing devices pursuant to part 15 of FCC rules, which are
designed to provide reasonable protection against radio frequency interference. Operation of this equipment in other environments may
cause interference with radio communications, in which case the user at his own expense will be required to take whatever measures may
be required to correct this interference.
EVM WARNINGS AND RESTRICTIONS
It is important to operate this EVM within the input voltage range of 2.5 V to 5 V and the output voltage range of 0 V to 5.5 V.
Exceeding the specified input range may cause unexpected operation and/or irreversible damage to the EVM. If there are questions
concerning the input range, please contact a TI field representative prior to connecting the input power.
Applying loads outside of the specified output range may result in unintended operation and/or possible permanent damage to the EVM.
Please consult the EVM User's Guide prior to connecting any load to the EVM output. If there is uncertainty as to the load specification,
please contact a TI field representative.
During normal operation, some circuit components may have case temperatures greater than 60°C. The EVM is designed to operate
properly with certain components above 60°C as long as the input and output ranges are maintained. These components include but are
not limited to linear regulators, switching transistors, pass transistors, and current sense resistors. These types of devices can be identified
using the EVM schematic located in the EVM User's Guide. When placing measurement probes near these devices during operation,
please be aware that these devices may be very warm to the touch.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2008, Texas Instruments Incorporated
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Amplifiers
Applications
Audio
Automotive
Broadband
Digital Control
Medical
Military
Optical Networking
Security
amplifier.ti.com
dataconverter.ti.com
Data Converters
DLP® Products
DSP
Clocks and Timers
Interface
dsp.ti.com
interface.ti.com
logic.ti.com
power.ti.com
microcontroller.ti.com
Logic
Power Mgmt
Microcontrollers
RFID
Telephony
Video & Imaging
Wireless
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2009, Texas Instruments Incorporated
Download from Www.Somanuals.com. All Manuals Search And Download.
|