ADDENDUM TO
MODEL 100E
OPERATORS MANUAL
(P/N 04515)
FOR
MODEL 100EU
TRACE LEVEL SULFUR DIOXIDE
ANALYZER
9480 CARROLL PARK DRIVE
SAN DIEGO, CA 92121-5201
USA
Toll-free Phone: 800-324-5190
Phone: 858-657-9800
Fax: 858-657-9816
Email: [email protected]
05831 Rev C
DCN 5379
© 2007 T-API
PRINT DATE: 08 April 2009
08 April 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
M100EU – OPERATIONS MANUAL
Addendum to M100E Manual - P/N 04515
TELEDYNE INSTRUMENTS
TABLE OF CONTENTS
TABLE OF CONTENTS
PREFACE ..........................................................................................................................................................................3
Reference Numbering convention.............................................................................................................................3
SPECIFICATIONS, APPROVALS AND WARRANTY.......................................................................................................5
Specifications............................................................................................................................................................5
EPA Equivalency Designation...................................................................................................................................6
CE Mark Compliance ................................................................................................................................................6
Warranty ...................................................................................................................................................................6
GETTING STARTED..........................................................................................................................................................7
Unpacking the M100EU ............................................................................................................................................7
Internal Layouts ........................................................................................................................................................7
Functional Check of the M100EU .............................................................................................................................8
Test Functions......................................................................................................................................................8
FREQENTLY ASKED QUESTIONS & GLOSSARY........................................................................................................11
OPTIONAL HARDWARE AND SOFTWARE...................................................................................................................13
M100EU OPERATING INSTRUCTIONS..........................................................................................................................15
Additional Test Parameters.....................................................................................................................................15
STBL MENU: Setup for the Three Stability Functions.............................................................................................15
CALIBRATION PROCEDURES.......................................................................................................................................17
EPA PROTOCOL CALIBRATION ...................................................................................................................................19
INSTRUMENT MAINTENANCE.......................................................................................................................................21
THEORY OF OPERATION..........................................................................................................................................23
TROUBLESHOOTING & REPAIR ..............................................................................................................................27
Electronic Operation................................................................................................................................................23
Sensor Module ..............................................................................................................................................23
Sample Chamber......................................................................................................................................24
Fault Diagnosis with Warning Messages.......................................................................................................27
Fault Diagnosis with Test Functions..............................................................................................................27
Fault Diagnosis with Sync Demod PCA LEDs...............................................................................................29
Other Performance Problems .................................................................................................................................29
Additional Repair Procedures .................................................................................................................................29
UV Lamp Adjustment and/or Replacement ...................................................................................................29
Adjusting the UV Lamp (Peaking the Lamp ..............................................................................................30
Replacing the UV Lamp............................................................................................................................32
Replacing the UV filter/lens.............................................................................................................................33
Replacing the PMT, HVPS or TEC................................................................................................................34
M100EU PMT Hardware Calibration (Factory Cal)........................................................................................36
Technical Assistance ..............................................................................................................................................37
05944 Rev B
DCN 5063
1
PRINTED DOCUMENTS ARE UNCONTROLLED
Download from Www.Somanuals.com. All Manuals Search And Download.
TELEDYNE INSTRUMENTS
TABLE OF CONTENTS
M100EU – OPERATIONS MANUAL
Addendum to M100E Manual - P/N 04515
LIST OF FIGURES
M100EU Internal Layout................................................................................................................7
M100EU Sensor Module Assembly.............................................................................................24
M100EU Sample Chamber Exploded View................................................................................25
UV Lamp Adjustment...................................................................................................................31
LIST OF TABLES
Test Functions Defined..................................................................................................................8
Test Functions - Possible Causes for Out-Of-Range Values......................................................27
USER NOTES:
2
05944 Rev B
DCN 5063
PRINTED DOCUMENTS ARE UNCONTROLLED
Download from Www.Somanuals.com. All Manuals Search And Download.
M100EU – OPERATIONS MANUAL
Addendum to M100E Manual - P/N 04515
TELEDYNE INSTRUMENTS
PREFACE
1. PREFACE
NOTE
The information contained in this addendum is pertinent to M100EU analyzers running software revision
F.0. Some or all of the information may not be applicable to later revisions of software.
The software revision your analyzer is running is displayed in the upper left-hand corner of the display
any time the instrument is in SETUP mode.
This addendum is based on the Model 100E Operators Manual (P/N 04145). In most ways the M100EU is
identical to the M100E in design and operation, therefore most of the basic set up information, operating
instructions as well as calibration, maintenance, troubleshooting and repair methods are found in that manual.
This addendum documents only those areas where the M100EU is different in design or operating method from
the M100E.
Therefore this addendum includes instructions and information regarding:
Additional Test Functions
Adjusting the PMT HV for “Factory Calibrations”
Differences in theory of operation
1.1 REFERENCE NUMBERING CONVENTION
Unless otherwise specified, chapter, section, figure and table reference numbers referred to within this text are
relative to this document.
EXAMPLE: “Figure 2-1” refers to the figure, within this document, labeled as 2-1.
References to chapters, sections, figures and tables in the original document will be labeled as such.
EXAMPLE: “Figure 6.1 of the M101E Operators Manual (P/N 04145, REV. A)”.
USER NOTES
05944 Rev B
DCN 5063
3
PRINTED DOCUMENTS ARE UNCONTROLLED
Download from Www.Somanuals.com. All Manuals Search And Download.
TELEDYNE INSTRUMENTS
PREFACE
M100EU – OPERATIONS MANUAL
Addendum to M100E Manual - P/N 04515
USER NOTES:
4
05944 Rev B
PRINTED DOCUMENTS ARE UNCONTROLLED
DCN 5063
Download from Www.Somanuals.com. All Manuals Search And Download.
M100EU – OPERATIONS MANUAL
Addendum to M100E Manual - P/N 04515
TELEDYNE INSTRUMENTS
SPECIFICATIONS, APPROVALS AND WARRANTY
2. SPECIFICATIONS, APPROVALS AND
WARRANTY
2.1 SPECIFICATIONS
Table 2-1:
Model 100EU Basic Unit Specifications
Min/Max Range
In 1ppb increments from 50ppb to 20 000ppb, dual ranges or auto ranging
(Physical Analog Output)
Measurement Units
Zero Noise2
ppb, ppm, µg/m3, mg/m3 (user selectable)
25 ppt RMS (50 ppt RMS with 360 nM filter installed)
0.5% of reading RMS, above 5 ppb
50 ppt RMS
Span Noise2
Lower Detectable Limit3
Zero Drift (24 hours)
Zero Drift (7 days)
Span Drift (7 Days)
Linearity
<200 ppt (<400 ppt with 360 nM filter installed)
<200 ppt (<400 ppt with 360 nM filter installed)
<0.5% FS
1% of full scale
Precision
0.5% of reading
Temperature Coefficient
Lag Time1
< 0.1% per oC
30 sec
Rise/Fall Time1
95% in <140 sec
Sample Flow Rate
Temperature Range
Humidity Range
Dimensions H x W x D
650cc/min. ±10%
5-40oC
0 - 95% RH, non-condensing
7" x 17" x 23.5" (178 mm x 432 mm x 597 mm)
45 lbs (20.5 kg) w/internal pump
Weight, Analyzer
(Basic Configuration)
AC Power Rating
100 V, 50/60 Hz (3.25A);
115 V, 60 Hz (3.0 A);
220 – 240 V, 50/60 Hz (2.5 A)
Environmental
Installation category (over-voltage category) II; Pollution degree 2
Three (3) Outputs
Analog Outputs
Analog Output Ranges
100 mV, 1 V, 5 V, 10 V, 2-20 or 4-20 mA isolated current loop.
All Ranges with 5% Under/Over Range
Analog Output Resolution
Status Outputs
1 part in 4096 of selected full-scale voltage
8 Status outputs from opto-isolators
Control Inputs
Serial I/O
6 Control Inputs, 3 defined, 3 spare
One (1) RS-232; One (1) RS-485 (2 connecters in parallel)
Baud Rate : 300 – 115200: Optional Ethernet Interface
Certifications
EN61326 (1997 w/A1: 98) Class A, FCC Part 15 Subpart B Section 15.107 Class
A, ICES-003 Class A (ANSI C63.4 1992) & AS/NZS 3548 (w/A1 & A2; 97)
Class A.
IEC 61010-1:90 + A1:92 + A2:95,
1-As defined by the USEPA; 2 – 25 samples taken, 10 sec. interval; 3 – Twice zero noise
05944 Rev B
DCN 5063
5
PRINTED DOCUMENTS ARE UNCONTROLLED
Download from Www.Somanuals.com. All Manuals Search And Download.
TELEDYNE INSTRUMENTS
SPECIFICATIONS, APPROVALS AND WARRANTY
M100EU – OPERATIONS MANUAL
Addendum to M100E Manual - P/N 04515
2.2 EPA EQUIVALENCY DESIGNATION
At this time the M100EU has not been certified by the EPA as an equivalent method at the time of this writing
however it is anticipated that the M100EU will qualify as Reference Method Number EQSA-0495-100 per 40
CFR Part 53 in the near future. Please see section 2.2 of the M100E manual, P/N 04515 for details.
2.3 CE MARK COMPLIANCE
See Section 2.3 of the M100E Manual - P/N 04515
2.4 WARRANTY
See Section 2.4 of the M100E Manual - P/N 04515
User Notes:
6
05944 Rev B
DCN 5063
PRINTED DOCUMENTS ARE UNCONTROLLED
Download from Www.Somanuals.com. All Manuals Search And Download.
M100EU – OPERATIONS MANUAL
Addendum to M100E Manual - P/N 04515
TELEDYNE INSTRUMENTS
GETTING STARTED
3. GETTING STARTED
3.1 UNPACKING THE M100EU
Unpack the M100EU as per the directions in Section 3.1 of the M100E Manual - P/N 04515, with the following
change. There are two redheaded shipping screws that hold down the PMT/Sensor assembly and must be
removed prior to operation. They are located along the base of the PMT housing adjacent to the chassis.
3.2 INTERNAL LAYOUTS
Figures 3-1 replaces Figure 3-9 in the M100E manual. The primary difference between the M100EU and M100E
layouts is the differences in the PMT Housing, the location of the PMT preamp PCA and the addition of a Sync
Demodulator PCA.
Figure 3-1:
M100EU Internal Layout
05944 Rev B
DCN 5063
7
PRINTED DOCUMENTS ARE UNCONTROLLED
Download from Www.Somanuals.com. All Manuals Search And Download.
TELEDYNE INSTRUMENTS
GETTING STARTED
M100EU – OPERATIONS MANUAL
Addendum to M100E Manual - P/N 04515
3.3 FUNCTIONAL CHECK OF THE M100EU
To perform an initial functional check of the M100EU follow the steps contained in Section 3.2.4 of the M100E
Manual - P/N 04145, but use the Test functions described in below.
3.3.1
TEST FUNCTIONS
Table 3-1 supersedes the figure in Step 2 of Section 3.2.4 and Figure 6-2 of the M100E Manual - P/N 04145.
Table 11-1 supersedes Table 6-2. The only differences between the M100E and M100EU’s test functions are
the addition of STABIL2 and UV STAB.
Table 3-1:
UNITS
Test Functions Defined
DISPLAY
PARAMETER
DESCRIPTION
The Full Scale limit at which the reporting range of the analyzer’s
ANALOG OUTPUTS is currently set.
RANGE
- -
PPB,
PPM,
UGM &
MGM
THIS IS NOT the Physical Range of the instrument. See Section
6.7 of M100E manual for more information.
RANGE
RANGE1
RANGE2
If DUAL or AUTO Range modes have been selected, two
RANGE functions will appear, one for each range.
Standard deviation of SO2 Concentration readings. Data points
are recorded every ten seconds. The calculation uses the last
25 data points.
STABIL
STABILITY
ppb
Standard deviation of SO2 Concentration readings, per EPA.
Data points are recorded every 120 seconds. The calculation
uses the last 25 data points.
STABIL2
PRES
STABILITY
ppb
The current pressure of the sample gas as it enters the sample
chamber, measured between the SO2 and Auto-Zero valves.
SAMPLE PRESSURE
in-Hg-A
The flow rate of the sample gas through the sample chamber.
This value is not measured but calculated from the sample
pressure.
cm³/min
(cc/m)
SAMP FL
SAMPLE FLOW
PMT Signal
PMT
mV
mV
The raw output voltage of the PMT.
NORMALIZED PMT
Signal
The output voltage of the PMT after normalization for offset and
temperature/pressure compensation (if activated).
NORM PMT
Source UV Lamp
Intensity
UV LAMP
UV STAB
mV
mV
The output voltage of the UV reference detector.
Standard deviation of UV reference detector output. Data points
are recorded every ten seconds. The calculation uses the last
25 data points.
Stability of UV Lamp
Intensity
The current output of the UV reference detector divided by the
reading stored in the CPU’s memory from the last time a UV
Lamp calibration was performed.
LAMP RATIO
UV Source lamp ratio
%
The offset due to stray light recorded by the CPU during the last
zero-point calibration performed.
STR. LGT
DRK PMT
DRK LMP
Stray Light
Dark PMT
ppb
mV
mV
The PMT output reading recorded the last time the UV source
lamp shutter was closed.
The UV reference detector output reading recorded the last time
the UV source lamp shutter was closed.
Dark UV Source Lamp
The sensitivity of the instrument as calculated during the last
calibration activity. The slope parameter is used to set the span
calibration point of the analyzer.
SLOPE
SO2 measurement Slope
-
(table continued)
8
05944 Rev B
PRINTED DOCUMENTS ARE UNCONTROLLED
DCN 5063
Download from Www.Somanuals.com. All Manuals Search And Download.
M100EU – OPERATIONS MANUAL
Addendum to M100E Manual - P/N 04515
TELEDYNE INSTRUMENTS
GETTING STARTED
Table 3-1:
Test Functions Defined
DISPLAY
PARAMETER
SO2 measurement Offset
HVPS
UNITS
DESCRIPTION
The overall offset of the instrument as calculated during the last
calibration activity. The offset parameter is used to set the zero
point of the analyzer response.
OFFSET
-
HVPS
V
The PMT high voltage power supply.
SAMPLE CHAMBER
TEMP
RCELL TEMP
°C
The current temperature of the sample chamber.
BOX TEMP
PMT TEMP
BOX TEMPERATURE
PMT TEMPERATURE
°C
°C
The ambient temperature of the inside of the analyzer case.
The current temperature of the PMT.
The current temperature of the internal zero/span option. Only
appears when IZS option is enabled
IZS TEMP1
TEST2
IZS TEMPERATURE1
TEST SIGNAL2
°C
mV
Signal of a user-defined test function on output channel A4.
hh:mm:s
s
TIME
CLOCK TIME
The current day time for iDAS records and calibration events.
To view the TEST Functions press the following Key sequence:
SAMPLE
RANGE = 500.0 PPB
SO2 =XXX.X
SETUP
< TST TST > CAL
RANGE
STABIL
STABIL2
PRES
SAMP FL
PMT
Toggle <TST TST> keys to
scroll through list of functions
NORM PMT
UV LAMP
UV STAB
LAMP RATIO
STR. LGT
DARK PMT
DARK LAMP
SLOPE
Refer to
Section
6.2.1 for
definitions
of these
test
OFFSET
HVPS
functions.
1 Only appears if IZS option is
installed.
RCELL TEMP
BOX TEMP
PMT TEMP
IZS TEMP1
TEST2
2 Only appears if analog output
A3 is actively reporting a test
function
TIME
Figure 3-2:
M100EU Test Functions
05944 Rev B
DCN 5063
9
PRINTED DOCUMENTS ARE UNCONTROLLED
Download from Www.Somanuals.com. All Manuals Search And Download.
TELEDYNE INSTRUMENTS
GETTING STARTED
M100EU – OPERATIONS MANUAL
Addendum to M100E Manual - P/N 04515
USER NOTES:
10
05944 Rev B
PRINTED DOCUMENTS ARE UNCONTROLLED
DCN 5063
Download from Www.Somanuals.com. All Manuals Search And Download.
M100EU – OPERATIONS MANUAL
Addendum to M100E Manual - P/N 04515
TELEDYNE INSTRUMENTS
FREQENTLY ASKED QUESTIONS & GLOSSARY
4. FREQENTLY ASKED QUESTIONS & GLOSSARY
Please refer to Section 4 of the M100E manual, PN 04515 for information.
05944 Rev B
11
DCN 5063
PRINTED DOCUMENTS ARE UNCONTROLLED
Download from Www.Somanuals.com. All Manuals Search And Download.
TELEDYNE INSTRUMENTS
FREQUENTLY ASKED QUESTIONS & GLOSSARY
M100EU – OPERATIONS MANUAL
Addendum to M100E Manual - P/N 04515
USER NOTES:
12
05944 Rev B
PRINTED DOCUMENTS ARE UNCONTROLLED
DCN 5063
Download from Www.Somanuals.com. All Manuals Search And Download.
M100EU – OPERATIONS MANUAL
Addendum to M100E Manual - P/N 04515
TELEDYNE INSTRUMENTS
OPTIONAL HARDWARE AND SOFTWARE
5. OPTIONAL HARDWARE AND SOFTWARE
Please refer to Section 5 of the M100E manual, PN 04515 for information.
05944 Rev B
13
DCN 5063
PRINTED DOCUMENTS ARE UNCONTROLLED
Download from Www.Somanuals.com. All Manuals Search And Download.
TELEDYNE INSTRUMENTS
OPTIONAL HARDWARE AND SOFTWARE
M100EU – OPERATIONS MANUAL
Addendum to M100E Manual - P/N 04515
USER NOTES:
14
05944 Rev B
PRINTED DOCUMENTS ARE UNCONTROLLED
DCN 5063
Download from Www.Somanuals.com. All Manuals Search And Download.
M100EU – OPERATIONS MANUAL
Addendum to M100E Manual - P/N 04515
TELEDYNE INSTRUMENTS
M100EU OPERATING INSTRUCTIONS
6. M100EU OPERATING INSTRUCTIONS
NOTE
For the most part the operation instruction for the M100EU are the same as those described in Chapter 6
of the M100E Manual - P/N 04515 with the exception that there are additional test parameters and setup
procedures.
6.1 ADDITIONAL TEST PARAMETERS
6.2 STBL MENU: SETUP FOR THE THREE STABILITY
FUNCTIONS
There is an additional submenu on the Secondary Setup Menu in the M100EU’s software. The STBL menu, see
Figure 6-1 allows the user to modify the settings for the three stability calculations that are displayed as Test
Functions on the front panel and are available via the serial data port and that can be logged with the iDAS.
Test Function STABIL, CONC1 in the menus below, is equivalent to the standard M100E STABIL function and is
useful when conducting calibrations and other operations in which the operator has limited time to view the
display. CONC2, which is the same as the STABIL2 test function has been configured so that it calculates
stability in the same way as required by the EPA. STABIL2 is useful when comparing instruments against the
EPA standard but is very slow and difficult to use for calibration or other activities where the operator must wait
for analyzer to settle to the desired value. UVLAMP is the same as UV STAB on the front panel is a diagnostic
that can be used to understand the stability of the UV lamp.
05944 Rev B
DCN 5063
15
PRINTED DOCUMENTS ARE UNCONTROLLED
Download from Www.Somanuals.com. All Manuals Search And Download.
TELEDYNE INSTRUMENTS
M100EU OPERATING INSTRUCTIONS
M100EU – OPERATIONS MANUAL
Addendum to M100E Manual - P/N 04515
SAMPLE
RANGE = 500.000 PPB
SO2 =XXX.X
< TST TST > CAL
SETUP
SETUP X.X
PRIMARY SETUP MENU
EXIT returns
to the main
SAMPLE
display
CFG DAS RNGE PASS CLK MORE
EXIT
SETUP X.X
SECONDARY SETUP MENU
EXIT returns
to the PRIMARY
SETUP MENU
COMM VARS DIAG STBL
SETUP X.X
NEXT
CONC1, 10SEC, 25 SAMPLES
EDIT PRNT EXIT
SETUP X.X
CONC2, 120SEC, 25 SAMPLES
PREV NEXT
EDIT PRNT EXIT
CONC2 is
setup for
STABIL2 test
function,
UVLAMP for
UV STAB test
function
SETUP X.X
PREV
UVLAMP, 10SEC, 25 SAMPLES
EDIT PRNT EXIT
Figure 6-1:
Accessing the STBL Menu
User Notes:
16
05944 Rev B
DCN 5063
PRINTED DOCUMENTS ARE UNCONTROLLED
Download from Www.Somanuals.com. All Manuals Search And Download.
M100EU – OPERATIONS MANUAL
Addendum to M100E Manual - P/N 04145
TELEDYNE INSTRUMENTS
CALIBRATION PROCEDURES
7. CALIBRATION PROCEDURES
Calibration of the M100EU should be performed according to the procedures described in Chapters 7 & 8 of the
M100E Manual - P/N 04145. However, delivering span and zero gases for the lower ranges that the M100EU is
designed for can be difficult. For best results when calibrating the M100EU, wait one hour for the instrument to
stabilize when delivering zero and span gases before pressing the zero and span buttons. Attention must be
paid to the quality of the gasses, the level of contaminants in the gases as well as the history and conditioning of
the gas delivery components. Only Teflon or glass should be used for any “wetted” surfaces that the calibration
gasses contact. All delivery system components should be conditioned by running span gas for a minimum of
four hours before conducting actual span calibrations.
05944 Rev B
DCN 5063
17
PRINTED DOCUMENTS ARE UNCONTROLLED
Download from Www.Somanuals.com. All Manuals Search And Download.
TELEDYNE INSTRUMENTS
CALIBRATION PROCEDURES
M100EU – OPERATIONS MANUAL
Addendum to M100E Manual - P/N 04515
USER NOTES:
18
05944 Rev B
PRINTED DOCUMENTS ARE UNCONTROLLED
DCN 5063
Download from Www.Somanuals.com. All Manuals Search And Download.
M100EU – OPERATIONS MANUAL
Addendum to M100E Manual - P/N 04145
TELEDYNE INSTRUMENTS
EPA PROTOCOL CALIBRATION
8. EPA PROTOCOL CALIBRATION
The M100EU is designated as an equivalent method for measuring SO2 under certification EQSA-0495-100.
Calibration of the M100EU is done so in a manner that is consistent with EPA requirements. For calibration in
this manner please refer to section 8 of the M100E manual.
05944 Rev B
19
DCN 5063
PRINTED DOCUMENTS ARE UNCONTROLLED
Download from Www.Somanuals.com. All Manuals Search And Download.
TELEDYNE INSTRUMENTS
EPA PROTOCOL CALIBRATION
M100EU – OPERATIONS MANUAL
Addendum to M100E Manual - P/N 04515
USER NOTES:
20
05944 Rev B
PRINTED DOCUMENTS ARE UNCONTROLLED
DCN 5063
Download from Www.Somanuals.com. All Manuals Search And Download.
M100EU – OPERATIONS MANUAL
Addendum to M100E Manual - P/N 04145
TELEDYNE INSTRUMENTS
INSTRUMENT MAINTENANCE
9. INSTRUMENT MAINTENANCE
Instrument maintenance is almost identical to that in the M100E. The M100EU uses a 1 micron sample filter, instead of the 5
micron sample filter used in the M100E. Replacement part numbers are shown below.
Part Number
009690200
05920
Description
AKIT, TFE FLTR ELEMENT, 47MM, 1UM (100)
UV Zinc LAMP, M100EU
For all other maintenance questions, please refer to section 9 in the M100E manual.
05944 Rev B
21
DCN 5063
PRINTED DOCUMENTS ARE UNCONTROLLED
Download from Www.Somanuals.com. All Manuals Search And Download.
TELEDYNE INSTRUMENTS
INSTRUMENT MAINTENANCE
M100EU – OPERATIONS MANUAL
Addendum to M100E Manual - P/N 04515
USER NOTES:
22
05944 Rev B
PRINTED DOCUMENTS ARE UNCONTROLLED
DCN 5063
Download from Www.Somanuals.com. All Manuals Search And Download.
M100EU – OPERATIONS MANUAL
Addendum to M100E Manual - P/N 04145
TELEDYNE INSTRUMENTS
THEORY OF OPERATION
10.THEORY OF OPERATION
The M100EU is a modified M100E. The primary differences are the way in which the PMT and UV reference
signals are acquired and processed. The M100EU has no shutter but rather employs synchronous
demodulation to capture the dark and light PMT and UV reference signals several times per second. A printed
circuit board, the Sync Demodulator, attached to the end of the PMT housing, on the sensor assembly, includes
circuitry that digitizes the PMT and UV reference signals and synchronizes the operation of the UV source with
these measurements. This method of signal processing minimizes the error that changing offsets could make in
an instrument that is designed to operate near its detection limit.
10.1 ELECTRONIC OPERATION
The following information is in addition to that contained in Section 10.2 of the M100E Manual - P/N 04145.
10.1.1 SENSOR MODULE
At the heart of the M100EU’s signal processing, illustrated in Figure 10-1 below, is the Synchronous
Demodulator PCA. The PCA is attached to the end of the PMT housing and serves to seal the end of the PMT
housing. The sync demodulator controls the operation of the UV Lamp driver, digitizes the analog output
signals from the PMT UV reference detector and PMT temperature sensor, controls the PMT cooler (TEC),
controls the PMT HV via a local I2C bus, and communicates with the analyzer’s CPU over the master I2C bus.
Digitized and processed data from the UV reference and PMT are passed to the analyzer’s CPU over the master
I2C bus and data for control of the PMT HV control DAC is passed from the CPU to the DAC on the PMT
preamp via the microcontroller on the Sync Demod board.
SYNC DEMOD PCA
(End of PMT Housing)
UV REF PCA
(End of Sensor Module)
UV LAMP DRIVER
PCA
(Side of Sensor Assy)
UV REF
Lamp Sync
`
PMT PREAMP PCA
(Inside PMT Housing)
PMT Signal
A/D
Converter
PMT HV
Monitor
PMT IN
CPU
MOTHERBOARD
(Rear Panel)
8 bit DAC
Local I2C Bus
Micro
Controller
PMT HV
Control
I2C
Master
I2C Bus
PMT Temp Sensor
(Inside PMT Housing)
PMT Cooler
(End of PMT Housing)
Figure 10-1:
Sensor Block Diagram
05944 Rev B
DCN 5063
23
PRINTED DOCUMENTS ARE UNCONTROLLED
Download from Www.Somanuals.com. All Manuals Search And Download.
TELEDYNE INSTRUMENTS
THEORY OF OPERATION
M100EU – OPERATIONS MANUAL
Addendum to M100E Manual - P/N 04515
Lamp Shutter Housing
UV LAMP
Reaction Cell
Sample Gas Outlet
PMT PREAMP PCA
SAMPLE
CHAMBER
Sample Gas Inlet
PMT HOUSING
Reference Detector
PMT Cooling System
Figure 10-2:
M100EU Sensor Module Assembly
These components are divided into two significant subassemblies. The sample chamber and the PMT
assembly.
Figure 10-3 shows an exploded view of the sample chamber assembly
Figure 11-3 shows an exploded view of the PMT Assembly
10.1.1.1
Sample Chamber
The main electronic components of the sample chamber are the reference detector(see Section 10.2.2 of the
M100E Manual - P/N 04145); the UV Lamp (see Section 10.2.1 of the M100E Manual - P/N 04145) and its
electronically operated shutter (see Section 9.2.1 of this addendum); and the sample chamber heating circuit,
24
05944 Rev B
DCN 5063
PRINTED DOCUMENTS ARE UNCONTROLLED
Download from Www.Somanuals.com. All Manuals Search And Download.
M100EU – OPERATIONS MANUAL
Addendum to M100E Manual - P/N 04145
TELEDYNE INSTRUMENTS
THEORY OF OPERATION
UV Source
Lamp
Shutter Housing
PMT Lens &
Housing
UV Source Lens &
Housing
Sample Air
Outlet
O-Ring
Seal
O-Ring
Seal
Sample Air
Inlet
Sample Chamber
Heater 1
Sample Chamber
Sample Chamber
Temperature Sensor
& Heater 2
Light Trap
Heater Safety
Shut-Off
Reference
Detector
Figure 10-3:
M100EU Sample Chamber Exploded View
05944 Rev B
DCN 5063
25
PRINTED DOCUMENTS ARE UNCONTROLLED
Download from Www.Somanuals.com. All Manuals Search And Download.
TELEDYNE INSTRUMENTS
THEORY OF OPERATION
M100EU – OPERATIONS MANUAL
Addendum to M100E Manual - P/N 04515
User Notes:
26
05944 Rev B
PRINTED DOCUMENTS ARE UNCONTROLLED
DCN 5063
Download from Www.Somanuals.com. All Manuals Search And Download.
M100EU – OPERATIONS MANUAL
Addendum to M100E Manual - P/N 04145
TELEDYNE INSTRUMENTS
TROUBLESHOOTING & REPAIR
11. TROUBLESHOOTING& REPAIR
This section includes various troubleshooting and repair information that is either in addition to that included in
Chapter 11 of the M100E Manual (P/N 04145)
CAUTION
THE OPERATIONS OUTLINED IN THIS CHAPTER MUST BE PERFORMED BY QUALIFIED
MAINTENANCE PERSONNEL ONLY.
PLEASE READ CHAPTER 11 OF THE M100E MANUAL (P/N 04145) BEFORE
ATTEMPTING THE FOLLOWING TROUBLE SHOOTING OR REPAIR PROCEDURES
CAUTION
RISK OF ELECTRICAL SHOCK. SOME OPERATIONS NEED TO BE CARRIED OUT WITH
THE ANALYZER OPEN AND RUNNING.
EXERCISE CAUTION TO AVOID ELECTRICAL SHOCKS AND ELECTROSTATIC OR
MECHANICAL DAMAGE TO THE ANALYZER.
DO NOT DROP TOOLS INTO THE ANALYZER OR LEAVE THOSE AFTER YOUR
PROCEDURES.
DO NOT SHORTEN OR TOUCH ELECTRIC CONNECTIONS WITH METALLIC TOOLS
WHILE OPERATING INSIDE THE ANALYZER.
USE COMMON SENSE WHEN OPERATING INSIDE A RUNNING ANALYZER.
11.1.1 FAULT DIAGNOSIS WITH WARNING MESSAGES
The warning messages for the M100EU are identical to those included in Section 11.1.1 of the M100E Manual
(P/N 04145)
11.1.2 FAULT DIAGNOSIS WITH TEST FUNCTIONS
The following table supersedes Table 11.2 of the M100E Manual - P/N 04145.
Table 11-1:
Test Functions - Possible Causes for Out-Of-Range Values
TEST
FUNCTION
NOMINAL
VALUE(S)
POSSIBLE CAUSE(S)
Faults that cause high stability values are: pneumatic leak; low or very unstable UV lamp
output; light leak; faulty HVPS; defective preamp board; aging PMT; PMT recently exposed to
room light; dirty/contaminated reaction cell.
STABIL
0.075 ppb with zero
air
(STANDARD)
STABIL2
0.075 ppb with zero
Same as STABIL
air
(EPA DEF)
650 cm3/min
± 10%
Faults can be caused by: clogged critical flow orifice; pneumatic leak; faulty flow sensor;
sample line flow restriction.
SAMPLE FL
High or noisy readings could be due to: calibration error; pneumatic leak; light leak (improper
assembly); aging UV filter; low UV reference output; PMT recently exposed to room light; light
leak in reaction cell; reaction cell contaminated; HVPS problem.
-20 TO 150 mV with
zero air
PMT
It takes 24-48 hours for a PMT exposed to ambient light levels to return to normal functioning.
(table continued)
05944 Rev B
DCN 5063
27
PRINTED DOCUMENTS ARE UNCONTROLLED
Download from Www.Somanuals.com. All Manuals Search And Download.
TELEDYNE INSTRUMENTS
TROUBLESHOOTING & REPAIR
M100EU – OPERATIONS MANUAL
Addendum to M100E Manual - P/N 04515
Table 11-1:
Test Functions - Possible Causes for Out-Of-Range Values
TEST
FUNCTION
NOMINAL
VALUE(S)
POSSIBLE CAUSE(S)
Noisy Norm PMT value (assuming unchanging SO2 concentration of sample gas):
Calibration error; HVPS problem; PMT problem; UV reference problem; UV lamp problem.
NORM PMT
- -
This is the instantaneous reading of the UV lamp intensity. Low UV lamp intensity could be
due to: aging UV lamp; UV lamp position out of alignment; faulty lamp transformer; aging or
faulty UV detector; dirty optical components.
UV LAMP
UV STAB
2000 - 4000 mV
0 to 100 mV
Intensity lower than 600 mV will cause UV LAMP WARNING.
Unstable lamp or failed UV lamp driver.
The current output of the UV reference detector divided by the reading stored in the CPU’s
memory from the last time a UV Lamp calibration was performed. Out of range lamp ratio
could be due to: malfunctioning UV lamp; UV lamp position out of alignment; faulty lamp
transformer; aging or faulty UV detector; dirty optical components; pin holes or scratches in the
UV optical filters; light leaks.
LAMP RATIO
30 TO 120%
High stray light could be caused by: aging UV filter; contaminated reaction cell; light leak;
pneumatic leak.
STR LGT
DRK PMT
<100 ppb
High dark PMT reading could be due to: light leak; high pmt temperature; high electronic
offset.
200 - 325 mV
DRK LMP
HVPS
-50 - +200 mV
High dark UV detector could be caused by: light leak; high electronic offset.
≈ 400 V to 900 V
Incorrect HVPS reading could be caused by; HVPS broken; preamp board circuit problems.
Incorrect temperature reading could be caused by: malfunctioning heater; relay board
communication (I1C bus); relay burnt out
RCELL TEMP
BOX TEMP
PMT TEMP
50ºC ± 1ºC
ambient
+ ~ 5ºC
Incorrect temperature reading could be caused by: Environment out of temperature
operating range; broken thermistor; runaway heater
Incorrect temperature reading could be caused by: TEC cooling circuit broken; High chassis
temperature; 12V power supply
7ºC ± 2ºC constant
50ºC ± 1ºC
Malfunctioning heater; relay board communication (I1C bus); relay burnt out
IZS TEMP
(OPTION)
Incorrect SAMPLE pressure could be due to: pneumatic leak; malfunctioning valve;
malfunctioning pump; clogged flow orifices; sample inlet overpressure; faulty pressure
sensor
ambient
± 2 IN-HG-A
PRESS
Slope out of range could be due to: poor calibration quality ; span gas concentration incorrect;
leaks; UV Lamp output decay.
SLOPE
OFFSET
1.0 ± 0.3
< 250 mV
High offset could be due to: incorrect span gas concentration/contaminated zero air/leak; low-
level calibration off; light leak; aging UV filter; contaminated reaction cell; pneumatic leak.
Incorrect Time could be caused by: Internal clock drifting; move across time zones; daylight
savings time?
TIME OF DAY
Current time
28
05944 Rev B
PRINTED DOCUMENTS ARE UNCONTROLLED
DCN 5063
Download from Www.Somanuals.com. All Manuals Search And Download.
M100EU – OPERATIONS MANUAL
Addendum to M100E Manual - P/N 04145
TELEDYNE INSTRUMENTS
TROUBLESHOOTING & REPAIR
11.1.3 FAULT DIAGNOSIS WITH SYNC DEMOD PCA LEDS
There are four green Light Emitting Diodes (LEDs) on the bottom left side of the Sync Demodulator PCA. They
indicate various statuses and can be used to troubleshoot problems associated with the board.
Table 11-2:
Relay PCA Status LED Failure Indications
Indicator
Function
Description
Toggles on or off
Action
DS4
Watchdog
Steady on or off controller on PCA has crashed, PMT
temp. control still operates but PMT, REF and PMT Temp
voltages as shown in test functions will be XXXX. Press
reset button on sync demod to restart, if problem
continues check power supply voltages on PCA or PCA is
failing and must be replaced
every second
DS3
I2C Activity
Flashes each time
Steady on or off indicates I2C bus failure check wiring
sync demod is polled harness taking I2C to motherboard, another I2C device is
by instrument CPU
once every 1 to 1.5
seconds
hanging bus, I2C transceiver on motherboard has failed,
or CPU has problem
DS2
DS1
A/D Status 1
A/D Status 2
Short frequent
Lack of flash indicates internal failure of A/D or firmware.
flashes tracks timing Press reset button on sync demod to restart, if problem
of A/D converter
continues check power supply voltages on PCA or PCA is
failing and must be replaced
11.2 OTHER PERFORMANCE PROBLEMS
Please refer to Section 11.4 of the M100E manual, P/N 04515 for information.
11.3 ADDITIONAL REPAIR PROCEDURES
The following repair procedures are in addition to those listed in Section 11.6 of the M100E Manual - P/N 04145,
11.3.1 UV LAMP ADJUSTMENT AND/OR REPLACEMENT
There are two ways in which ambient conditions can affect the UV Lamp output and therefore the accuracy of the
SO2 concentration measurement. These are:
LAMP AGING
Over a period of months, the UV energy will show a downward trend, usually 30% - 50% in the first 90 days, and
then a slower rate, until the end of useful life of the lamp. Periodically running the UV lamp calibration routine
(see Section 6.9.7 of the M100E Manual - P/N 04145) will compensate for this until the lamp output becomes too
low to function at all, 2-3 years nominally.
LAMP POSITIONING
05944 Rev B
DCN 5063
29
PRINTED DOCUMENTS ARE UNCONTROLLED
Download from Www.Somanuals.com. All Manuals Search And Download.
TELEDYNE INSTRUMENTS
TROUBLESHOOTING & REPAIR
M100EU – OPERATIONS MANUAL
Addendum to M100E Manual - P/N 04515
The UV output level of the lamp is not even across the entire length of the lamp. Some portions of the lamp
shine slightly more brightly than others. At the factory the position of the UV lamp is adjusted to optimize the
amount of UV light shining through the UV filter/lens and into the reaction cell. Changes to the physical
alignment of the lamp can affect the analyzer’s ability to accurately measure SO2. See Section 11.6.3.2 of the
M100E Manual (P/N 04145) for instructions on adjusting the lamp position.
11.3.1.1
Adjusting the UV Lamp (Peaking the Lamp
CAUTION:
ALWAYS WEAR UV-PROTECTIVE, SAFETY GLASSES WHEN WORKING WITH THE UV
LAMP ASSEMBLY
1. Set the analyzer display to show the signal I/O function, UVLAMP_SIGNAL (see Section 11.1.3 of the
M100E Manual - P/N 04145). UVLAMP_SIGNAL is function 35.
2. Slightly loosen the large brass thumbscrew located on the shutter housing (see Figure 10-1) so that the
lamp can be moved.
3. While watching the UVLAMP_SIGNAL reading, slowly rotate the lamp or move it back and forth
vertically until the UVLAMP_SIGNAL reading is at its maximum.
Best peak intensity will occur when the dot (or arrow) on top of the lamp is pointing in the direction of the
reaction cell.
Ideally, the reading should be 4000mV±200mV.
If UVLAMP_SIGNAL is lower than 600mV, replace the lamp.
If UVLAMP_SIGNAL is greater than 4400 mV, adjust the pot on the UV reference board down until the
output reads 4400 mV, and then continue to peak the lamp.
NOTE:
Always grasp the main body of the lamp.
30
05944 Rev B
DCN 5063
PRINTED DOCUMENTS ARE UNCONTROLLED
Download from Www.Somanuals.com. All Manuals Search And Download.
M100EU – OPERATIONS MANUAL
Addendum to M100E Manual - P/N 04145
TELEDYNE INSTRUMENTS
TROUBLESHOOTING & REPAIR
Figure 11-1:
4. Finger tighten the thumbscrew
UV Lamp Adjustment
NOTE
DO NOT over tighten the thumbscrew
05944 Rev B
DCN 5063
31
PRINTED DOCUMENTS ARE UNCONTROLLED
Download from Www.Somanuals.com. All Manuals Search And Download.
TELEDYNE INSTRUMENTS
TROUBLESHOOTING & REPAIR
M100EU – OPERATIONS MANUAL
Addendum to M100E Manual - P/N 04515
11.3.1.2
Replacing the UV Lamp
1. Turn off the analyzer.
2. Disconnect the UV lamp from its power supply.
You can find the power supply connector by following the two, white UV Lamp power supply wires
from the lamp to the power supply.
3. Loosen, but do not remove the two UV lamp bracket screws, and the large brass thumbscrew located on
NOTE:
Always grasp the main body of the lamp.
4. Remove the UV Lamp by pulling it straight up.
5. Insert the new UV lamp into the bracket.
6. Tighten the two UV lamp bracket screws, but leave the brass thumb screw un-tightened.
7. Connect the new UV lamp to the power supply.
8. Turn the instrument on and perform the UV adjustment procedure as defined in section 10.5.1.1 of this
addendum
9. Finger tighten the thumbscrew.
NOTE:
DO NOT over-tighten the thumbscrew.
10. Perform a lamp calibration procedure (see Section 6.9.7 of the M100E Manual - P/N 04145) and a zero
point and span point calibration (see Chapter 7 of the M100E Manual - P/N 04145).
32
05944 Rev B
PRINTED DOCUMENTS ARE UNCONTROLLED
DCN 5063
Download from Www.Somanuals.com. All Manuals Search And Download.
M100EU – OPERATIONS MANUAL
Addendum to M100E Manual - P/N 04145
TELEDYNE INSTRUMENTS
TROUBLESHOOTING & REPAIR
11.3.2 REPLACING THE UV FILTER/LENS
Note:
Be careful not to leave thumbprints on the interior of the sample chamber. The various oils that make
up fingerprints fluoresce brightly under UV light and will significantly affect the accuracy of the
analyzer’s SO2 measurement)
1. Turn off the instrument’s power and remove the power cord from the instrument.
2. Unplug the J4 connector from the motherboard to allow tool access.
4. Remove 4 screws from the UV filter retainer.
Reaction
Cell
UV Filter Retainer
Screws
Lamp Housing
UV Filter Retainer
and Lens Housing
Lamp Housing
Cover Screws
UV Filter
UV Filter Retainer
Screws
Figure 11-2:
Disassembling the Shutter Assembly
5. Carefully remove the UV filter.
6. Install the UV filter with arrow pointing towards reaction cell. Handle carefully and never touch the filter’s
surface. The UV filter’s wider ( ring ) side should be facing out. Install the UV filter retainer and tighten
screws.
7. Install the lamp housing cover and mini-fit connector. Tighten 4 screws.
8. Re-plug J4 connector into the motherboard.
05944 Rev B
DCN 5063
33
PRINTED DOCUMENTS ARE UNCONTROLLED
Download from Www.Somanuals.com. All Manuals Search And Download.
TELEDYNE INSTRUMENTS
TROUBLESHOOTING & REPAIR
M100EU – OPERATIONS MANUAL
Addendum to M100E Manual - P/N 04515
11.3.3 REPLACING THE PMT, HVPS OR TEC
The PMT should last for the lifetime of the analyzer. However, in some cases, the high voltage power supply
(HVPS) or the thermo-electric cooler (TEC) may fail. To replace the PMT, the HVPS or the TEC:
Sync/ Demod PCA
Gasket
Leak Check Fitting
Pre Amp
Shield
Pre Amp
PCA
High Voltage Power Supply
(HVPS)
O-Test LED
PMT Housing
PMT
Insulation Gasket
PMT Cold Block
Connector to PMT
Pre Amp PCA
PMT Temperature
Sensor
12V Power
Connector
Light from Reaction
Chamber shines
through hole in side
of Cold Block
FOV Mask
Thermo-Electric
Cooler (TEC)
PMT Heat
Exchange Fins
TEC Driver
PCA
Cooling Fan
Housing
Figure 11-3:
PMT Assembly - Exploded View
1. Power down the analyzer, disconnect the power cord, remove the cover and disconnect all pneumatic
and electrical connections from the sensor assembly.
2. Remove the entire sensor module assembly from the analyzer.
3. Remove the fluorescence cell assembly.
4. Remove the two connectors on the Sync Demod board
5. Remove the Sync Demod Board (6 screws with plastic washers). Disconnect the electrical connector
that leads to the preamp board further inside the housing.
6. Remove all of the desiccant bags inside the PMT housing.
7. Along with the plate, slide out the OPTIC TEST LED and the thermistor that measures the PMT
temperature.
The thermistor will be coated with a white, thermal conducting paste. Do not contaminate the inside
of the housing or the PMT tube with this grease.
8. Unscrew the PMT assembly. It is held to the cold block by two plastic screws.
34
05944 Rev B
PRINTED DOCUMENTS ARE UNCONTROLLED
DCN 5063
Download from Www.Somanuals.com. All Manuals Search And Download.
M100EU – OPERATIONS MANUAL
Addendum to M100E Manual - P/N 04145
TELEDYNE INSTRUMENTS
TROUBLESHOOTING & REPAIR
Because the threads of the plastic screws are easily damaged it is highly recommended to use new
screws when reassembling the unit.
9. Carefully take out the assembly consisting of the HVPS, the gasket, preamp assembly and the PMT.
10. Change the PMT or the HVPS or both, clean the PMT glass tube with a clean, anti-static wipe and do
not touch it after cleaning.
11. If the cold block or TEC is to be changed disconnect the TEC driver board from the preamplifier board.
a) Remove the cooler fan duct (4 screws on its side) including the driver board.
b) Disconnect the driver board from the TEC and set the sub-assembly aside.
c) Remove the end plate with the cooling fins (4 screws) and slide out the PMT cold block assembly,
which contains the TEC.
d) Unscrew the TEC from the cooling fins and the cold block and replace it with a new unit.
12. Re-assemble the TEC subassembly in reverse order.
NOTE
The thermo-electric cooler needs to be mounted flat to the heat sink.
If there is any significant gap, the TEC might burn out.
Make sure to apply heat sink paste before mounting it and tighten the screws evenly and cross-wise.
a) Make sure to use thermal grease between the TEC and the cooling fins as well as between the TEC
and the cold block.
b) Align the side opening in the cold block with the hole in the PMT housing where the sample Chamber
attaches.
c) Evenly tighten the long mounting screws for good thermal conductivity.
13. Re-insert the TEC subassembly.
Make sure that the O-ring is placed properly and the assembly is tightened evenly.
14. Insert the LED and thermistor into the cold bloc.
15. Re-insert the PMT/HVPS subassembly.
Don’t forget the gasket between HVPS and PMT.
Use new plastic screws to mount the PMT assembly on the PMT cold block.
16. Insert the new desiccant bags.
17. Reconnect the cable from the preamp board to the back of the Sync Demod board then carefully
reattach the Sync Demod board to the housing
Make sure that the gasket is between the back of the board and the front of the PMT housing.
Be sure to tighten these screws evenly,
18. Reconnect the cables and the reaction cell
19. Replace the sensor assembly into the chassis and fasten with four screws and washers.
20. Reconnect all electrical and pneumatic connections, leak check the system and power up the analyzer.
Verify the basic operation of the analyzer using the ETEST and OTEST features (see Section 6.9.5 &
6.9.6 of the M100E Manual - P/N 04145) or by measuring calibrated zero and span gases.
21. Perform a PMT Hardware calibration (see Section 11.6.6 of the M100E Manual - P/N 04145)
22. Perform a zero point and span calibration (See Chapter 7 of the M100E Manual - P/N 04145)
05944 Rev B
DCN 5063
35
PRINTED DOCUMENTS ARE UNCONTROLLED
Download from Www.Somanuals.com. All Manuals Search And Download.
TELEDYNE INSTRUMENTS
TROUBLESHOOTING & REPAIR
M100EU – OPERATIONS MANUAL
Addendum to M100E Manual - P/N 04515
11.3.4 M100EU PMT HARDWARE CALIBRATION (FACTORY CAL)
THIS PROCEDURE SUPERSEDES THE ONE CONTAINED IN SECTION 11.6.3 OF THE M100E MANUAL -
P/N 04145.
The sensor module hardware calibration adjusts the slope of the PMT output when the Instruments slope and
offset values are outside of the acceptable range and all other more obvious causes for this problem have been
eliminated. Because the PMT HV is remotely controlled and there is no PMT preamp gain adjust, this procedure
is done automatically through the analyzer software.
1. Set the instrument reporting range to SNGL & 500 ppb (see Section 6.7.4 of the M100E Manual - P/N
04145)
2. Perform a full zero–point calibration using zero air (see Chapter 7 of the M100E Manual - P/N 04145).
3. Let the instrument stabilize by allowing it to run for one hour.
4. Adjust the UV Lamp. (See Section 10.5.1.1 of this addendum)
5. Perform a LAMP CALIBRATION procedure (see Section 6.9.7 of the M100E Manual - P/N 04145).
6. Feed 400 ppb span gas into the analyzer.
7. Wait approximately 30-60 minutes (or until the stability reads ≤ 0.1 ppb), then under the DIAG menu
select PMT CALIBRATION.
8. Either press ENTR if you are using 400 ppb or change the concentration value to what is appropriate
and then press ENTR.
9. Select the range that you wish to setup (low or high).
10. Wait two to three minutes until you get a message that indicates the HV has been adjusted successfully.
NOTE
If a reporting range other than 500 ppb is used in this procedure:
Use a span gas equal to 80% of the reporting range and adjust the PMT to a target NORM PMT value of
twice the ppb value of the span gas.
EXAMPLE
If the reporting range is 800 ppb then set the target concentration to 640 ppb for this procedure.
11. Wait until the STABIL value is ≤ 0.1 ppb.
12. Scroll to the NORM PMT value and verify that it is approximately twice the ppb value of the span gas.
13. Perform a zero / span calibration.
14. Check the slope and offset values and compare them to the values in Table 7-5 of the M100E Manual -
P/N 04145.
15. Steps 7 - 14 may have to be performed more than once in order to compensate for any
over/undershooting of the PMT reading based on the adjusted HVPS drive voltage. Best results occur
after performing the PMT calibration (steps 7 - 14) at least two consecutive times
36
05944 Rev B
DCN 5063
PRINTED DOCUMENTS ARE UNCONTROLLED
Download from Www.Somanuals.com. All Manuals Search And Download.
M100EU – OPERATIONS MANUAL
Addendum to M100E Manual - P/N 04145
TELEDYNE INSTRUMENTS
TROUBLESHOOTING & REPAIR
11.4 TECHNICAL ASSISTANCE
If this addendum and its trouble-shooting / repair sections do not solve your problems, technical assistance may
be obtained from:
Teledyne Instruments
Advanced Pollution Instrumentation Division
(TAPI)
Customer Service
9480 Carroll Park Drive
San Diego, California 92121-5201USA
Toll-free Phone: 800-324-5190
Phone: 858-657-9800
Fax: 858-657-9816
Email: [email protected]
Website: http://www.Teledyne-API.com
Before you contact Teledyne Instruments’ Customer service, fill out the problem report form in Appendix C,
which is also available online for electronic submission at http://www.Teledyne-API.com/forms/p-fmapicom.asp.
05944 Rev B
DCN 5063
37
PRINTED DOCUMENTS ARE UNCONTROLLED
Download from Www.Somanuals.com. All Manuals Search And Download.
TELEDYNE INSTRUMENTS
TROUBLESHOOTING & REPAIR
M100EU – OPERATIONS MANUAL
Addendum to M100E Manual - P/N 04515
USER NOTES:
38
05944 Rev B
PRINTED DOCUMENTS ARE UNCONTROLLED
DCN 5063
Download from Www.Somanuals.com. All Manuals Search And Download.
TELEDYNE INSTRUMENTS
APPENDIX A - Version Specific Software Documentation
Model 100EU Instruction Manual
APPENDIX A - Version Specific Software Documentation
APPENDIX A-1: MODEL 100EU SOFTWARE MENU TREES
APPENDIX A-2: MODEL 100EU SETUP VARIABLES AVAILABLE VIA SERIAL I/O
APPENDIX A-3: MODEL 100EU WARNINGS AND TEST MEASUREMENTS VIA SERIAL I/O
APPENDIX A-4: MODEL 100EU SIGNAL I/O DEFINITIONS
APPENDIX A-5: MODEL 100EU IDAS FUNCTIONS
APPENDIX A-6: MODEL 100EU TERMINAL COMMAND DESIGNATORS
05928 Rev F.0B
Pg: A-1
DCN 5063
PRINTED DOCUMENTS ARE UNCONTROLLED
Download from Www.Somanuals.com. All Manuals Search And Download.
TELEDYNE INSTRUMENTS
APPENDIX A-1: M100EU Software Menu Trees, Revision F.0B
Model 100EU Instruction Manual
APPENDIX A-1: M100E Software Menu Trees, Revision F.0B
Pg: A-2
05928 Rev F.0B
DCN 5063
PRINTED DOCUMENTS ARE UNCONTROLLED
Download from Www.Somanuals.com. All Manuals Search And Download.
TELEDYNE INSTRUMENTS
Model 100E Instruction Manual
APPENDIX A-1: M100E Software Menu Trees, Revision F.0B
SAMPLE
TEST1
CAL
MSG1,2
CLR1,3
SETUP
Only appear if
reporting range
is set for
AUTO range
mode.
ENTER SETUP PASS: 818
LOW
HIGH
<TST TST>
(Primary Setup Menu)
CFG
DAS
RANG
PASS
CLK
MORE
RANGE
STABIL
STABIL2
PRES
ZERO
SPAN
CONC
(Secondary Setup Menu)
SAMP FL
PMT
NORM PMT
UV LAMP
UV STB
COMM VARS
DIAG
LAMP RATIO
STR. LGT
DARK PMT
DARK LMP
SLOPE
OFFSET
HVPS
RCELL TEMP
BOX TEMP
PMT TEMP
IZS TEMP4
TEST5
1 Only appears when warning messages are activated
(see Section 6.2.2)
TEST FUNCTIONS
Viewable by user while
instrument is in
SAMPLE Mode
(see Section 6.2.1)
2 Press this key to cycle through list of active warning
messages.
3 Press this key to clear/erase the warning message
currently displayed
4 Only appears if the IZS valve option is installed.
5 Only appears if the TEST analog output channel is
activated.
TIME
Figure A-1: Basic Sample Display Menu
05928 Rev F.0B
DCN 5063
PG: A-3
PRINTED DOCUMENTS ARE UNCONTROLLED
Download from Www.Somanuals.com. All Manuals Search And Download.
TELEDYNE INSTRUMENTS
APPENDIX A-1: M100EU Software Menu Trees, Revision F.0B
Model 100EU Instruction Manual
SAMPLE
TEST1
CAL
CALS
MSG1,2
CLR1,3
SETUP
CALZ
Only appear if
reporting range
is set for
<TST TST>
LOW
HIGH
LOW
HIGH
LOW
HIGH
CONC
AUTO range
mode.
RANGE
STABIL
STABIL2
PRES
ZERO
SPAN
CONC
ZERO
SPAN
ENTER SETUP PASS: 818
SAMP FL
PMT
NORM PMT
UV LAMP
LAMP RATIO
STR. LGT
DRK PMT
DRK LAMP
SLOPE
(Primary Setup Menu)
CFG
DAS
RANG
PASS
CLK
MORE
OFFSET
HVPS
(Secondary Setup Menu)
RCELL TEMP
BOX TEMP
PMT TEMP
IZS TEMP4
1
Only appears when warning messages are activated
(see Section 6.2.2)
Press this key to cycle through list of active warning
messages.
2
3
TEST5
TEST FUNCTIONS
Viewable by user while
COMM VARS
DIAG
Press this key to clear/erase the warning message
instrument is in SAMPLE Mode
(see Section 6.2.1)
currently displayed
4
5
Only appears if the IZS valve option is installed.
Only appears if the TEST analog output channel is
activated.
Figure A-2: Sample Display Menu - Units with Z/S Valve or IZS Option installed
PRINTED DOCUMENTS ARE UNCONTROLLED
Pg: A-4
05928 Rev F.0B
DCN 5063
Download from Www.Somanuals.com. All Manuals Search And Download.
TELEDYNE INSTRUMENTS
Model 100E Instruction Manual
APPENDIX A-1: M100E Software Menu Trees, Revision F.0B
SETUP
ENTER SETUP PASS: 818
ACAL1
CFG
DAS
RNGE
PASS
CLK
MORE
ON
PREV
NEXT
Go To iDAS
MENU TREE
(Fig. A-8)
PREV
NEXT
MODE
SET2
OFF
MODEL NAME
SERIAL NUMBER
TIME
DATE
SEQ 1)
SEQ 2)
SEQ 3)
SOFTWARE
REVISION
LIBRARY REVISION
iCHIP SOFTWARE
MODE
IND
SET
UNIT
REVISION1
HESSEN PROTOCOL
REVISION1
ACTIVE SPECIAL
SOFTWARE
PREV
NEXT
OPTIONS1
CPU TYPE
SNGL
AUTO
DATE FACTORY
CONFIGURATION
SAVED
DISABLED
ZERO
PPB
PPM
UGM
MGM
ZERO/SPAN
SPAN
ENTR
ENTR
TIMER ENABLE
STARTING DATE
STARTING TIME
DELTA DAYS
DELTA TIME
Go To
1
2
3
Only appears if a applicable
option/feature is installed and
activated.
Only appears whenever the
currently displayed sequence
is not set for DISABLED.
Only appears when reporting
range is set to AUTO range
mode.
SECONDARY SETUP MENU
<SET SET>
LOW3 HIGH3
EDIT
(Fig. A-5)
DURATION
CALIBRATE
RANGE TO CAL3
Figure A-3: Primary Setup Menu (Except iDAS)
05928 Rev F.0B
DCN 5063
PG: A-5
PRINTED DOCUMENTS ARE UNCONTROLLED
Download from Www.Somanuals.com. All Manuals Search And Download.
TELEDYNE INSTRUMENTS
APPENDIX A-1: M100EU Software Menu Trees, Revision F.0B
Model 100EU Instruction Manual
SAMPLE
ENTER SETUP PASS: 818
ACAL1
CFG
DAS
RNGE
PASS
CLK
MORE
VIEW
PREV NEXT
EDIT
CONC
PREV NEXT
INS
DEL
EDIT
PRNT
PNUMTC
CALDAT
DETAIL
FAST
YES
NO
CONC
PNUMTC
CALDAT
DETAIL
FAST
VIEW
NEXT
<SET
SET>
EDIT
PRNT
<PRM PRM> PV10
PREV
NX10
Selects data point to view.
Creates/changes name
(see Section 6.11.2.2).
Cycles through
lists of
parameters
chosen for this
iDAS channel
NAME
EVENT
PARAMETERS
REPORT PERIOD
NUMBER OF RECORDS
RS-232 REPORT
CHANNEL ENABLE
CAL. HOLD
Sets the
amount of time
between each
report.
YES
NO
PREV NEXT
PREV NEXT
INS
DEL
EDIT
PRNT
Cycles through
available trigger
events
(see Section 6.11.2.3).
YES
NO
ON
YES
NO
OFF
<SET
SET>
EDIT
PRNT
Cycles through
already active
parameters
(see Section 6.11.2.4).
Selects max
no. of records
for this channel
PARAMETER
PREV NEXT
SAMPLE MODE
PRECISION
INST
AVG
MIN
MAX
Cycles through available/active parameters
(see Section 6.12.2.4).
1
Only appears if Z/S valve or IZS option is installed.
Figure A-4: Primary Setup Menu (iDAS)
Pg: A-6
05928 Rev F.0B
DCN 5063
PRINTED DOCUMENTS ARE UNCONTROLLED
Download from Www.Somanuals.com. All Manuals Search And Download.
TELEDYNE INSTRUMENTS
Model 100E Instruction Manual
APPENDIX A-1: M100E Software Menu Trees, Revision F.0B
SAMPLE
ENTER SETUP PASS: 818
ACAL1
CFG
DAS
RNGE
PASS
VARS
CLK
MORE
DIAG
COMM
INET2
STBL
Password required
ID
COM1 COM23
PREV NEXT
EDIT
Go To INET MENU TREE
(Fig A-6)
CONC1
CONC2
UVLAMP
PERIOD
SAMPLES
<SET
SET>
EDIT
MODE
BAUD RATE TEST PORT
PREV NEXT JUMP
EDIT PRINT
PREV NEXT
PREV NEXT
TEST
DAS_HOLD_OFF
TPC_ENABLE
RCELL_SET
IZS_SET
DYN_ZERO
DYN_SPAN
CONC_PRECISION
CLOCK_ADJ
QUIET
COMPUTER
SECURITY
HESSEN PROTOCOL
E, 7, 1
300
1200
2400
4800
9600
19200
38400
57600
Go To
DIAG MENU TREE
(Fig A-8)
RS-485
MULTIDROP PROTOCOL
ENABLE MODEM
ERROR CHECKING
XON/XOFF HANDSHAKE
HARDWARE HANDSHAKE
HARDWARE FIFO
COMMAND PROMPT
1
Only appears if Z/S valve or IZS option is installed.
Only appears when the ENABLE INTERNET mode is
enabled.
115200
2
ON
3
OFF
Disappears when INET option is enabled.
Figure A-5: Secondary Setup Menu (COMM & VARS)
05928 Rev F.0B
DCN 5063
PG: A-7
PRINTED DOCUMENTS ARE UNCONTROLLED
Download from Www.Somanuals.com. All Manuals Search And Download.
TELEDYNE INSTRUMENTS
APPENDIX A-1: M100EU Software Menu Trees, Revision F.0B
Model 100EU Instruction Manual
SETUP
ENTER SETUP PASS: 818
ACAL1
CFG
DAS
RNGE
PASS
CLK
MORE
DIAG
COMM
<SET
VARS
ID
COM1
PREV NEXT JUMP
EDIT PRINT
INET2
COMM - VARS
MENU TREE
DAS_HOLD_OFF
TPC_ENABLE
RCELL_SET
IZS_SET
SET>
EDIT
(Fig A-5)
DYN_ZERO
DYN_SPAN
CONC_PRECISION
CLOCK_ADJ
DHCP
INSTRUMENT IP
GATEWAY IP
SUBNET MASK
TCP PORT3
HOSTNAME4
Go To
DIAG MENU TREE
(Fig A-8)
ON
INSTRUMENT IP5
GATEWAY IP5
SUBNET MASK5
TCP PORT3
OFF
EDIT
1 Only appears if a valve option is installed.
2 Only appears when the Ethernet card (option 63) is installed.
3 Although TCP PORT is editable regardless of the DHCP state, do not change the setting for this property unless
instructed to by Teledyne Instruments Customer Service personnel.
4 HOST NAME is only editable when DHCP is ON.
5 INSTRUMENT IP, GATEWAY IP & SUBNET MASK are only editable when DHCP is OFF.
Figure A-6: Secondary Setup Menu (COMM Menu with Ethernet Card)
Pg: A-8
05928 Rev F.0B
DCN 5063
PRINTED DOCUMENTS ARE UNCONTROLLED
Download from Www.Somanuals.com. All Manuals Search And Download.
TELEDYNE INSTRUMENTS
Model 100E Instruction Manual
APPENDIX A-1: M100E Software Menu Trees, Revision F.0B
.
SETUP
ENTER SETUP PASS: 818
ACAL1
CFG
DAS
RNGE
PASS
CLK
MORE
COMM
VARS
DIAG
HESN2
ID
COM1 COM2
See
See
Fig A-5
Fig A-8
<SET
SET> EDIT
See
Fig A-5
PMT DET WARNING
UV LAMP WARNING
DARK CAL WARNING
IZS TEMP WARNING
BOX TEMP WARNING
PMT TEMP WARNING
VARIATION RESPONSE MODE GAS LIST STATUS FLAGS
TYPE 1
TYPE 2
RCELL TEMP WARNING
SAMPLE FLOW WARNING
SAMPLE PRESS WARNING
HVPS WARNING
SYSTEN RESET
BCC
TEXT
CMD
REAR BOARD NOT DET
RELAY BOARD
FRONT PANEL
PREV NEXT
INS
DEL
EDIT
PRNT
ANALOG CAL WARNING
CANNOT DYN ZERO
CANNOT DYN SPAN
INVALID CONC
ZERO CAL
Select from list of
available gases
(see Section 6.12.4.6).
YES
NO
SPAN CAL
MANUAL MODE
GAS TYPE
GAS ID
REPORTED
Set Hessen ID number for
PPB
selected gas type
PPM
UGM
MGM
SO2, 110, REPORTED
See Table 6-27 for
Flag Assignments
(see Section 6.12.4.6).
1
2
Only appears if a valve is installed.
ON
OFF
Only appears when the HESSEN mode is enabled for
either COM1 or COM2.
Figure A-7: Secondary Setup Menu - HESSEN Submenu
05928 Rev F.0B
DCN 5063
PG: A-9
PRINTED DOCUMENTS ARE UNCONTROLLED
Download from Www.Somanuals.com. All Manuals Search And Download.
TELEDYNE INSTRUMENTS
APPENDIX A-1: M100EU Software Menu Trees, Revision F.0B
Model 100EU Instruction Manual
SAMPLE
ENTER SETUP PASS: 818
ACAL1
DAS
RNGE
PASS
CLK
MORE
CFG
DIAG
COMM
VARS
PREV NEXT
TEST
CALIBRATION CALIBRATION CHANNEL
OUTPUT
SIGNAL
I/O
ANALOG
OUTPUT CONFIGURATION
ANALOG I/O
OPTIC ELECTRICAL
LAMP
CALIBRATION
PRESSURE
FLOW
TEST
TEST
ENTR
ENTR
ENTR
ENTR
ENTR
ENTR
PREV NEXT
Start step Test
Starts Test
Starts Test
Starts Test
Starts Test
Starts Test
0) EXT ZERO CAL
1) EXT SPAN CAL
2) MAINT MODE
3) LANG2 SELECT
PMT
CALIB’N
NONE
PMT READING
UV READING
<SET SET>
4) SAMPLE LED
5) CAL LED
6) FAULT LED
7) AUDIBLE BEEPER
8) ELEC TEST
SAMPLE PRESSURE
SAMPLE FLOW
RCELL TEMP
AOUTS CALIBRATED
CAL
ENTR
CHASSIS TEMP
CONC OUT 1
CONC OUT 2
TEST OUTPUT
9) OPTIC TEST
IZS TEMP2
10) PREAMP RANGE HIGH
11) ST SYSTEM OK
12) ST CONC VALID
13) ST HIGH RANGE
14) ST ZERO CAL
PMT TEMP
HVPS VOLTAGE
15) ST SPAN CAL
16) ST DIAG MODE
17) ST LAMP ALARM
18) ST DARK CAL ALARM
19) ST FLOW ALARM
20) ST PRESS ALARM
21) SR TEMP ALARM
22) ST HVPS ALARM
24) ST SYSTEM ON2
25) RELAY WATCHDOG
26) RCELL HEATER
28) IZS HEATER1
EDIT
LOW HIGH
<SET SET>
REC OFFSET
Starts Test
RANGE
AUTO CAL
ON
CALIBRATED
CAL
ON
27) CAL VALVE
29) SPAN VALVE
30) H2S VALVE
31) DARK SHUTTER
OFF
30
52
INTERNAL ANALOG
VOLTAGE SIGNALS
(see Appendix A)
OFF
1
0.1V 1V
5V 10V CURR
Only relevant to analyzers with IZS options installed
Figure A-8: Secondary Setup Menu (DIAG)
Pg: A-10
05928 Rev F.0B
DCN 5063
PRINTED DOCUMENTS ARE UNCONTROLLED
Download from Www.Somanuals.com. All Manuals Search And Download.
TELEDYNE INSTRUMENTS
APPENDIX A - Version Specific Software Documentation
Model 100EU Instruction Manual
APPENDIX A-2: Setup Variables For Serial I/O, Revision F.0B
Table A-1: M100EU Setup Variables, Revision F.0B
M100EU Setup Variables for Latest Revision
Setup Variable
Numeric
Units
Default
Value
Value
Range
Description
DAS_HOLD_OFF
Minutes
15
0.5–20
Duration of DAS hold off period.
TPC_ENABLE
RCELL_SET
— ON,
OFF, ON
30–70
ON enables temperature and
pressure compensation; OFF
disables it.
OFF 4
ºC
ºC
50
Reaction cell temperature set
point and warning limits.
Warnings:
45–55
50
IZS_SET 1
30–70
IZS temperature set point and
warning limits.
Warnings:
45–55
DYN_ZERO
— OFF
— OFF
— 1
OFF, ON
OFF, ON
ON enables contact closure
dynamic zero; OFF disables it.
DYN_SPAN
ON enables contact closure
dynamic span; OFF disables it.
CONC_PRECISION
AUTO,
Number of digits to display to the
right of the decimal point for
concentrations on the display.
Enclose value in double quotes
(“) when setting from the RS-232
interface.
0,
1,
2,
3,
4
STABIL_GAS 99
— SO2
SO2,
O2 10
Selects gas for stability test
measurement.
,
CO2 11
CLOCK_ADJ
Sec./Day 0
— ENGL
-60–60
Time-of-day clock speed
adjustment.
LANGUAGE_SELECT
ENGL,
SECD,
EXTN
Selects the language to use for
the user interface. Enclose value
in double quotes (“) when setting
from the RS-232 interface.
MAINT_TIMEOUT
CONV_TIME
Hours 2
—
0.1–100
Time until automatically
switching out of software-
controlled maintenance mode.
33 MS
33 MS,
66 MS,
133 MS,
266 MS,
533 MS,
1 SEC,
2 SEC
Conversion time for PMT and UV
detector channels. Enclose value
in double quotes (“) when setting
from the RS-232 interface.
DWELL_TIME
Seconds 1,
0.1–10
Dwell time before taking each
05928 Rev F.0B
DCN 5063
A-11
PRINTED DOCUMENTS ARE UNCONTROLLED
Download from Www.Somanuals.com. All Manuals Search And Download.
TELEDYNE INSTRUMENTS
Model 100EU Instruction Manual
APPENDIX A - Version Specific Software Documentation
0.2 4
sample.
FILT_SIZE
Samples 240,
1–480
1–100
Moving average filter size.
30 3,
5 4
FILT_ASIZE
FILT_DELTA
FILT_PCT
Samples 20,
PPM 0.02,
% 5,
Moving average filter size in
adaptive mode.
6 3
0.001–0.1,
1–1003
Absolute change to trigger
adaptive filter.
10 3
10 2
1–100
Percent change to trigger
adaptive filter.
FILT_DELAY
FILT_ADAPT
Seconds 180
— ON,
0–300
Delay before leaving adaptive
filter mode.
OFF, ON
ON enables adaptive filter; OFF
disables it.
OFF 4
NEG_CONC_SUPPRESS
— OFF
OFF, ON
ON pegs negative concentrations
at zero; OFF permits negative
concentrations
DIL_FACTOR
— 1
0.1–1000
0.1–30
Dilution factor if dilution enabled
with FACTORY_OPT variable.
CO2_DWELL 11
Seconds 1
— ON
Dwell time before taking each
sample.
CO2_FILT_ADAPT 11
CO2_FILT_SIZE 11
CO2_FILT_ASIZE 11
CO2_FILT_DELTA 11
CO2_FILT_PCT 11
CO2_FILT_DELAY 11
CO2_DIL_FACTOR 11
ON, OFF
1–300
ON enables CO2 adaptive filter;
OFF disables it.
Samples 48
Samples 12
% 2
CO2 moving average filter size in
normal mode.
1–300
CO2 moving average filter size in
adaptive mode.
0.1–10
Absolute change in CO2
concentration to shorten filter.
% 10
0.1–100
0–300
Relative change in CO2
concentration to shorten filter.
Seconds 90
— 1
Delay before leaving CO2
adaptive filter mode.
0.1–1000
Dilution factor for CO2. Used only
if is dilution enabled with
FACTORY_OPT variable.
CO2_STD_CELL_TEMP 11
CO2_STD_CELL_PRESS 11
O2_DWELL 10
ºK 323
1–500
Standard CO2 cell temperature
for temperature compensation.
"Hg 28.50
Seconds 1
— ON
1.00–50.00
0.1–30
Standard CO2 cell pressure for
pressure compensation.
Dwell time before taking each
sample.
O2_FILT_ADAPT 10
O2_FILT_SIZE 10
ON, OFF
1–500
ON enables O2 adaptive filter;
OFF disables it.
Samples 60
Samples 10
O2 moving average filter size in
normal mode.
O2_FILT_ASIZE 10
1–500
O2 moving average filter size in
adaptive mode.
A-12
05928 Rev F.0B
DCN 5063
PRINTED DOCUMENTS ARE UNCONTROLLED
Download from Www.Somanuals.com. All Manuals Search And Download.
TELEDYNE INSTRUMENTS
APPENDIX A - Version Specific Software Documentation
Model 100EU Instruction Manual
O2_FILT_DELTA 10
O2_FILT_PCT 10
% 2
0.1–100
0.1–100
0–300
Absolute change in O2
concentration to shorten filter.
% 2
Relative change in O2
concentration to shorten filter.
O2_FILT_DELAY 10
O2_DIL_FACTOR 10
Seconds 20
— 1
Delay before leaving O2 adaptive
filter mode.
0.1–1000
Dilution factor for O2. Used only if
is dilution enabled with
FACTORY_OPT variable.
O2_CELL_SET 10
ºC
50
30–70
O2 sensor cell temperature set
point and warning limits.
Warnings:
45–55
O2_STD_CELL_TEMP 10
O2_STD_CELL_PRESS 10
USER_UNITS
ºK 323
1–500
Standard O2 cell temperature for
temperature compensation.
"Hg 28.50
— PPB,
1.00–50.00
Standard O2 cell pressure for
pressure compensation.
PPB,
PPM,
UGM,
MGM
Concentration units for user
interface. Enclose value in
double quotes (“) when setting
from the RS-232 interface.
PPM 3
PPM,
MGM 3
LAMP_DRIVE 6
LAMP_CAL
mV
5000
3500
0–5000
1000–5000
0.5–1.5
Lamp power setting.
mV
Last calibrated UV lamp reading.
LAMP_GAIN
— 0.9
UV lamp compensation
attenuation factor.
BXTEMP_TPC_GAIN
— 1,
0–10
Box temperature compensation
attenuation factor.
0 12
SPRESS_TPC_GAIN
— 1
0–10
Sample pressure compensation
attenuation factor.
PMT_TARG_CONC 12
PMT_UPDATE_PERIOD 12
PMT_CAL_TIMEOUT 12
Conc 400
Seconds 10
Minutes 5
0.01–9999.99
1–100
Target SO2 concentration during
PMT calibration.
Period between HVPS gain
updates during PMT calibration.
1–100
Maximum time for PMT
calibration to succeed.
HVPS_ADJUST 12
HVPS_INTEG 12
—
0
0–200
0–500
HVPS gain adjustment.
Gain 5
Integral coefficient for adjusting
HVPS gain during PMT
calibration.
HVPS_STABIL 12
— 1
0.1–10
HVPS gain must stabilize to
within this limit for PMT
calibration to succeed.
PMT_ADJUST 12
SLOPE_CONST
—
0
0–65535
0.1–10
PMT gain adjustment.
— 8,
Constant to make visible slope
close to 1.
6.25 3
05928 Rev F.0B
DCN 5063
A-13
PRINTED DOCUMENTS ARE UNCONTROLLED
Download from Www.Somanuals.com. All Manuals Search And Download.
TELEDYNE INSTRUMENTS
Model 100EU Instruction Manual
APPENDIX A - Version Specific Software Documentation
DARK_MODE 5
— AUT
O
OFF,
Dark calibration mode. OFF
disables it; AUTO does it
periodically; CMND does it only
when commanded. Enclose
value in double quotes (“) when
setting from the RS-232
interface.
AUTO,
CMND
DARK_ENABLE 1, 3, 4
DARK_FREQ
— ON,
OFF, ON
0.1–1440
1–60
ON enables PMT/UV dark
calibration; OFF disables it.
OFF 4
720 3
Minutes 30,
Seconds 10
Dark calibration period.
DARK_PRE_DWELL
Dwell time after closing dark
shutter or turning off lamp or
selecting preamp range.
DARK_POST_DWELL
Seconds 10,
1–180
Dwell time after opening dark
shutter or turning on lamp.
30 3
DARK_SAMPLES
DARK_FSIZE
DARK_LIMIT
Samples 5
Samples 2
mV 200,
1–10
Number of dark samples to
average.
1–100
0–1000
Dark offset moving average filter
size.
Maximum dark offset allowed.
400 3
SO2_TARG_ZERO1
SO2_SPAN1
Conc 0
-100–999.99
0.01–9999.99
Target SO2 concentration during
zero calibration of range 1.
Conc 400,
Target SO2 concentration during
span calibration of range 1.
4000 3
SO2_SLOPE1
PPB/mV,
PPM/mV 3
mV 0
1 0.25–
4
SO2 slope for range 1.
SO2_OFFSET1
-1500–1500
-100–999.99
SO2 offset for range 1.
SO2_TARG_ZERO2
Conc 0
Target SO2 concentration during
zero calibration of range 2.
SO2_SPAN2
Conc 400,
0.01–9999.99
4
Target SO2 concentration during
span calibration of range 2.
4000 3
SO2_SLOPE2
PPB/mV,
PPM/mV 3
mV 0
1 0.25–
SO2 slope for range 2.
SO2_OFFSET2
CO2_TARG_SPAN_CONC 11
-1500–1500
0.1–1000
SO2 offset for range 2.
% 12
Target CO2 concentration during
span calibration.
CO2_SLOPE 11
CO2_OFFSET 11
O2_TARG_SPAN_CONC 10
— 1
0.5–5
CO2 slope.
CO2 offset.
% 0
-10–10
0.1–100
% 20.95
Target O2 concentration during
span calibration.
O2_SLOPE 10
O2_OFFSET 10
RANGE_MODE
— 1
0.5–2
O2 slope.
O2 offset.
% 0
-10–10
SNGL,
DUAL,
AUTO,
— SNGL
Range control mode. Enclose
value in double quotes (“) when
setting from the RS-232
interface.
A-14
05928 Rev F.0B
DCN 5063
PRINTED DOCUMENTS ARE UNCONTROLLED
Download from Www.Somanuals.com. All Manuals Search And Download.
TELEDYNE INSTRUMENTS
APPENDIX A - Version Specific Software Documentation
Model 100EU Instruction Manual
AUTO2
PHYS_RANGE1
PHYS_RANGE2
CONC_RANGE1
CONC_RANGE2
PPM 2,
0.1–2500,
5–10000 3
0.1–2500,
5–10000 3
0.1–50000
Low pre-amp range.
500 3
PPM 22,
Conc 500,
Conc 500,
High pre-amp range.
5500 3
5000 3
5000 3
D/A concentration range 1.
D/A concentration range 2.
0.1–50000
CO2_RANGE 11
O2_RANGE 10
% 15
% 100
cc/m
0.1–500
0.1–500
0–6000
CO2 concentration range.
O2 concentration range.
SAMP_FLOW_SET
700,
250 1+9
Sample flow set point for flow
calculation and warning limits.
Warnings:
350–1200,
175–325 1+9
SAMP_FLOW_SLOPE
VAC_SAMP_RATIO 3
SAMP_PRESS_SET
— 1
0.5–1.5
0.1–2
Sample flow slope correction
factor (adjusted flow = measured
flow x slope).
— 0.53
"Hg
Maximum vacuum pressure /
sample pressure ratio for valid
sample flow calculation.
29.92
Warnings:
15–35
6
0–100
Sample pressure set point for
pressure compensation and
warning limits.
VAC_PRESS_SET 3
BOX_SET
"Hg
ºC
0–100
5–60
0–40
Vacuum pressure set point for
pressure compensation and
warning limits.
Warnings:
3–10
30
Box temperature warning limits.
Set point is not used.
Warnings:
8–50
PMT_SET
ºC
7,
15 12
PMT temperature set point and
warning limits.
Warnings:
2–12,
2–20 12
05928 Rev F.0B
DCN 5063
A-15
PRINTED DOCUMENTS ARE UNCONTROLLED
Download from Www.Somanuals.com. All Manuals Search And Download.
TELEDYNE INSTRUMENTS
Model 100EU Instruction Manual
APPENDIX A - Version Specific Software Documentation
RS232_MODE
BitFlag 0,
0–65535
RS-232 COM1 mode flags. Add
values to combine flags.
3 5
1 = quiet mode
2 = computer mode
4 = enable security
8 = enable hardware
handshaking
16 = enable Hessen protocol 8
32 = enable multi-drop
64 = enable modem
128 = ignore RS-232 line errors
256 = disable XON / XOFF
support
512 = disable hardware FIFOs
1024 = enable RS-485 mode
2048 = even parity, 7 data bits, 1
stop bit
4096 = enable command prompt
8192 = even parity, 8 data bits, 1
stop bit
16384 = enable dedicated
MODBUS ASCII protocol
32678 = enable dedicated
MODBUS RTU or TCP protocol
BAUD_RATE
— 192
00
300,
RS-232 COM1 baud rate.
Enclose value in double quotes
(“) when setting from the RS-232
interface.
1200,
2400,
4800,
9600,
19200,
38400,
57600,
115200
MODEM_INIT
—
“AT Y0 &D0
Any character
in the allowed
character set.
Up to 100
characters
long.
RS-232 COM1 modem
&H0 &I0 S0=2
&B0 &N6 &M0
E0 Q1 &W0”
initialization string. Sent verbatim
plus carriage return to modem on
power up or manually. Enclose
value in double quotes (“) when
setting from the RS-232
interface.
RS232_MODE2
BAUD_RATE2
BitFlag
— 192
0
0–65535
RS-232 COM2 mode flags.
(Same settings as
RS232_MODE.)
00
300,
RS-232 COM2 baud rate.
Enclose value in double quotes
(“) when setting from the RS-232
interface.
1200,
2400,
4800,
9600,
A-16
05928 Rev F.0B
DCN 5063
PRINTED DOCUMENTS ARE UNCONTROLLED
Download from Www.Somanuals.com. All Manuals Search And Download.
TELEDYNE INSTRUMENTS
APPENDIX A - Version Specific Software Documentation
Model 100EU Instruction Manual
19200,
38400,
57600,
115200
MODEM_INIT2
—
“AT Y0 &D0
Any character
in the allowed
character set.
Up to 100
characters
long.
RS-232 COM2 modem
&H0 &I0 S0=2
&B0 &N6 &M0
E0 Q1 &W0”
initialization string. Sent verbatim
plus carriage return to modem on
power up or manually. Enclose
value in double quotes (“) when
setting from the RS-232
interface.
RS232_PASS
Password
ID
940331
0–999999
0–9999
RS-232 log on password.
MACHINE_ID
100
”
Unique ID number for instrument.
COMMAND_PROMPT
— “Cmd>
Any character
in the allowed
character set.
Up to 100
characters
long.
RS-232 interface command
prompt. Displayed only if enabled
with RS232_MODE variable.
Enclose value in double quotes
(“) when setting from the RS-232
interface.
TEST_CHAN_ID
— NONE
NONE,
Diagnostic analog output ID.
Enclose value in double quotes
(“) when setting from the RS-232
interface.
PMT
READING,
UV READING,
VACUUM
PRESSURE3,
SAMPLE
PRESSURE,
SAMPLE
FLOW,
RCELL TEMP,
O2 CELL
TEMP 10
,
CHASSIS
TEMP,
IZS TEMP 1,
PMT TEMP,
HVPS
VOLTAGE
REMOTE_CAL_MODE
— LOW
LOW,
HIGH,
CO2 11
O2 10
Range to calibrate during
contact-closure and Hessen
calibration. Enclose value in
double quotes (“) when setting
from the RS-232 interface.
,
PASS_ENABLE
— OFF
OFF, ON
1–300
2–40
ON enables passwords; OFF
disables them.
STABIL_FREQ 99
STABIL_SAMPLES 99
RCELL_CYCLE
Seconds 10
Samples 25
Seconds 2
Stability measurement sampling
period.
Number of samples in
concentration stability reading.
0.5–30
Reaction cell temperature control
cycle period.
05928 Rev F.0B
DCN 5063
A-17
PRINTED DOCUMENTS ARE UNCONTROLLED
Download from Www.Somanuals.com. All Manuals Search And Download.
TELEDYNE INSTRUMENTS
Model 100EU Instruction Manual
APPENDIX A - Version Specific Software Documentation
RCELL_PROP
RCELL_INTEG
RCELL_DERIV
O2_CELL_CYCLE 10
O2_CELL_PROP 10
O2_CELL_INTEG 10
O2_CELL_DERIV 10
IZS_CYCLE 1
1/ºC
0.3 (prop. band 0–10
= 3.3 ºC)
Reaction cell temperature PID
proportional coefficient.
— 0.005
— 0.5
Seconds 10
— 1
0–10
Reaction cell temperature PID
integral coefficient.
0–10
Reaction cell temperature PID
derivative coefficient.
0.5–30
0–10
O2 cell temperature control cycle
period.
O2 cell PID temperature control
proportional coefficient.
— 0.1
— 0
0–10
O2 cell PID temperature control
integral coefficient.
(disabled)
0–10
O2 cell PID temperature control
derivative coefficient.
Seconds 2
1/ºC
0.5–30
0–10
IZS temperature control cycle
period.
IZS_PROP 1
1 (prop. band
= 1 ºC)
IZS temperature PID proportional
coefficient.
IZS_INTEG 1
— 0.03
— 0
0–10
IZS temperature PID integral
coefficient.
IZS_DERIV 1
0–10
IZS temperature PID derivative
coefficient.
HVPS_SET
Volts
650,
550 3
0–2000
High voltage power supply
warning limits. Set point is not
used.
Warnings:
400–900,
400–700 3
5
MAX_PMT_DETECTOR
PHOTO_ABS_LIMITS 1
mV 499
mV
0–5000
0–5000
PMT detector maximum warning
limit.
450
Pre-amplified UV lamp
minimum/maximum warning
limits. Set point is not used.
Warnings:
125–625
3500
UV_LAMP_LIMITS
mV
0–5000
UV lamp minimum/maximum
warning limits. Set point is not
used.
Warnings:
1000–4995
0
ELEC_TEST_LEVEL 12
OPTIC_TEST_LEVEL 12
CONC_LIN_ENABLE 3
—
0–65535
0–65535
OFF, ON
Electrical test level setting.
Optical test level setting.
—
0
— ON
ON enables concentration
linearization; OFF disables it.
SERIAL_NUMBER
— “000
00000 ”
Any character
in the allowed
character set.
Up to 100
Unique serial number for
instrument. Enclose value in
double quotes (“) when setting
from the RS-232 interface.
characters
long.
DISP_INTENSITY
— HIGH
HIGH,
MED,
LOW,
Front panel display intensity.
Enclose value in double quotes
(“) when setting from the RS-232
interface.
A-18
05928 Rev F.0B
DCN 5063
PRINTED DOCUMENTS ARE UNCONTROLLED
Download from Www.Somanuals.com. All Manuals Search And Download.
TELEDYNE INSTRUMENTS
APPENDIX A - Version Specific Software Documentation
Model 100EU Instruction Manual
DIM
I2C_RESET_ENABLE
CLOCK_FORMAT
— ON
—
OFF, ON
I2C bus automatic reset enable.
“TIME=%H:%
M:%S”
Any character
in the allowed
character set.
Up to 100
Time-of-day clock format flags.
Enclose value in double quotes
(“) when setting from the RS-232
interface.
characters
long.
“%a” = Abbreviated weekday
name.
“%b” = Abbreviated month name.
“%d” = Day of month as decimal
number (01 – 31).
“%H” = Hour in 24-hour format
(00 – 23).
“%I” = Hour in 12-hour format (01
– 12).
“%j” = Day of year as decimal
number (001 – 366).
“%m” = Month as decimal
number (01 – 12).
“%M” = Minute as decimal
number (00 – 59).
“%p” = A.M./P.M. indicator for
12-hour clock.
“%S” = Second as decimal
number (00 – 59).
“%w” = Weekday as decimal
number (0 – 6; Sunday is 0).
“%y” = Year without century, as
decimal number (00 – 99).
“%Y” = Year with century, as
decimal number.
“%%” = Percent sign.
FACTORY_OPT
BitFlag 0
0–65535
Factory option flags. Add values
to combine flags.
1 = enable dilution factor
2 = zero/span valves installed
4 = IZS installed (implies
zero/span valves installed)
8 = low span valve installed
16 = display units in
concentration field
32 = enable software-controlled
maintenance mode
64 = enable lamp power analog
output
128 = enable switch-controlled
maintenance mode
256 = compute only offset during
zero calibration
1024 = enable high flow rate
sensor
05928 Rev F.0B
DCN 5063
A-19
PRINTED DOCUMENTS ARE UNCONTROLLED
Download from Www.Somanuals.com. All Manuals Search And Download.
TELEDYNE INSTRUMENTS
Model 100EU Instruction Manual
APPENDIX A - Version Specific Software Documentation
2048 = enable Internet option
4096 = enable pre-amplified UV
lamp monitoring
1 M100E.
2 M100ES.
3 M100E H.
4 M100EF
.
5 RP84 00S.
6
Engineering firmware only.
7 iChi p option.
8
Must power-cycle instrument for these options to fully take effect.
9
Low span option.
10
O2 option.
11 CO 2 option.
12 M100E U.
99 Obsolete.
A-20
05928 Rev F.0B
PRINTED DOCUMENTS ARE UNCONTROLLED
DCN 5063
Download from Www.Somanuals.com. All Manuals Search And Download.
TELEDYNE INSTRUMENTS
APPENDIX A - Version Specific Software Documentation
Model 100EU Instruction Manual
APPENDIX A-3: Warnings and Test Functions, Revision F.0B
Table A-2: M100EU Warning Messages, Revision F.0B
Name 1
Message Text
Description
WSYSRES SYST
EM RESET
Instrument was power-cycled or the CPU
was reset.
WDATAINIT
DATA INITIALIZED
INITIALIZED
Data storage was erased.
WCONFIGINIT CONFIG
Configuration storage was reset to factory
configuration or erased.
WPMT
PMT DET WARNING
UV LAMP WARNING
SAMPLE FLOW WARN
SAMPLE PRESS WARN
PMT detector outside of warning limits
specified by DETECTOR_LIMIT variable.
WUVLAMP
WSAMPFLOW
WSAMPPRESS
UV lamp reading outside of warning limits
specified by DETECTOR_LIMIT variable.
Sample flow outside of warning limits
specified by SAMP_FLOW_SET variable.
Sample pressure outside of warning limits
specified by SAMP_PRESS_SET
variable.
WVACPRESS 5
VACUUM PRESS WARN
TEMP WARNING
Vacuum pressure outside of warning limits
specified by VAC_PRESS_SET variable.
WBOXTEMP BOX
WRCELLTEMP RCEL
Chassis temperature outside of warning
limits specified by BOX_SET variable.
L TEMP WARNING
Reaction cell temperature outside of
warning limits specified by RCELL_SET
variable.
WO2CELLTEMP 10
O2 CELL TEMP WARN
O2 sensor cell temperature outside of
warning limits specified by O2_CELL_SET
variable.
WIZSTEMP IZS
WPMTTEMP
TEMP WARNING
PMT TEMP WARNING
DARK CAL WARNING
WARNING
IZS temperature outside of warning limits
specified by IZS_SET variable.
PMT temperature outside of warning limits
specified by PMT_SET variable.
WDARKCAL 5
WHVPS HVPS
Dark offset above limit specified by
DARK_LIMIT variable.
High voltage power supply output outside
of warning limits specified by HVPS_SET
variable.
WDYNZERO
CANNOT DYN ZERO
CANNOT DYN SPAN
REAR BOARD NOT DET
RELAY BOARD WARN
FRONT PANEL WARN
ANALOG CAL WARNING
Contact closure zero calibration failed
while DYN_ZERO was set to ON.
WDYNSPAN
Contact closure span calibration failed
while DYN_SPAN was set to ON.
WREARBOARD
WRELAYBOARD
WFRONTPANEL
WANALOGCAL
Rear board was not detected during
power up.
Firmware is unable to communicate with
the relay board.
Firmware is unable to communicate with
the front panel.
The A/D or at least one D/A channel has
not been calibrated.
05928 Rev F.0B
DCN 5063
A-21
PRINTED DOCUMENTS ARE UNCONTROLLED
Download from Www.Somanuals.com. All Manuals Search And Download.
TELEDYNE INSTRUMENTS
Model 100EU Instruction Manual
APPENDIX A - Version Specific Software Documentation
Table A-3: M100EU Test Functions, Revision F.0B
Name 1
RANGE RANGE=
Message Text
500.0 PPB 3
Description
D/A range in single or auto-range modes.
SO2 RNG=500.0 PPB 3, 10, 11
RANGE1 RANGE1=50
RANGE2 RANGE2=50
0.0 PPB 3
SO2 RN1=500.0 PPB 3, 10, 11
0.0 PPB 3
SO2 RN2=500.0 PPB 3, 10, 11
CO2 RNG=100 PCT 11 CO
RNG=100 WT% 10
D/A #1 range in independent range mode.
D/A #2 range in independent range mode.
CO2RANGE
2 range.
O2RANGE O2
STABILITY ST
O2 range.
ABIL=0.0 PPB 3
Concentration stability #1. Configure with
SO2 STB=0.0 PPB 3, 10
O2 STB=0.0 WT% 10
CO2 STB=0.0 PCT 11
ABIL2=0.0 PPB 3
SETUP-MORE-STBL.
STABILITY2 6 ST
Concentration stability #2. Configure with
SO2 STB2=0.0 PPB 3, 10
O2 STB2=0.0 WT% 10
CO2 STB2=0.0 PCT 11
1.11(0.00) SEC
SETUP-MORE-STBL.
RESPONSE 2 RSP=
Instrument response. Length of each
signal processing loop. Time in
parenthesis is standard deviation.
VACUUM 5 VAC=9.1
SAMPPRESS
SAMPFLOW
IN-HG-A
PRES=29.9 IN-HG-A
SAMP FL=700 CC/M
PMT=762.5 MV
Vacuum pressure.
Sample pressure.
Sample flow rate.
Raw PMT reading.
PMTDET
NORMPMTDET
NORM PMT=742.9 MV
PMT reading normalized for temperature,
pressure, auto-zero offset, but not range.
UVDET
STABILITYUV 6
UV LAMP=3457.6 MV
UV STB=5.607 MV
UV lamp reading.
UV lamp stability reading.
LAMPRATIO
LAMP RATIO=100.0 %
UV lamp ratio of current reading divided
by calibrated reading.
STRAYLIGHT
DARKPMT
STR. LGT=0.1 PPB
DRK PMT=19.6 MV
DRK LMP=42.4 MV
Stray light offset.
PMT dark offset.
UV lamp dark offset.
DARKLAMP
SLOPE SLOPE=1.061
Slope for current range, computed during
zero/span calibration.
OFFSET OF
CO2SLOPE 11 CO2
CO2OFFSET 11
O2SLOPE 10 O2
O2OFFSET 10
A-22
FSET=250.0 MV
SLOPE=1.0000
Offset for current range, computed during
zero/span calibration.
CO2 slope, computed during zero/span
calibration.
CO2 OFFSET=0.00 %
SLOPE=0.980
CO2 offset, computed during zero/span
calibration.
O2 slope, computed during zero/span
calibration.
O2 OFFSET=1.79 %
O2 offset, computed during zero/span
05928 Rev F.0B
PRINTED DOCUMENTS ARE UNCONTROLLED
DCN 5063
Download from Www.Somanuals.com. All Manuals Search And Download.
TELEDYNE INSTRUMENTS
APPENDIX A - Version Specific Software Documentation
Model 100EU Instruction Manual
calibration.
HVPS
HVPS=650 VOLTS
High voltage power supply output.
RCELLDUTY
RCELL ON=0.00 SEC
Reaction cell temperature control duty
cycle.
RCELLTEMP
O2CELLTEMP 10
BOXTEMP
RCELL TEMP=52.1 C
O2 CELL TEMP=50.2 C
BOX TEMP=35.5 C
PMT TEMP=7.0 C
IZS ON=0.00 SEC
IZS TEMP=52.2 C
261.4 PPB
Reaction cell temperature.
O2 sensor cell temperature.
Internal chassis temperature.
PMT temperature.
PMTTEMP
IZSDUTY
IZS temperature control duty cycle.
IZS temperature.
IZSTEMP
SO2 SO2=
SO2 concentration for current range.
CO2 concentration.
CO2 11 CO2=
O2 10 O2=0.00
TESTCHAN T
0.00 PCT
WT%
O2 concentration.
EST=3721.1 MV
Value output to TEST_OUTPUT analog
output, selected with TEST_CHAN_ID
variable.
CLOCKTIME T
IME=10:38:27
Current instrument time of day clock.
1
The name is used to request a message via the RS-232 interface, as in “T BOXTEMP”.
2 Engi neering software.
3
Current instrument units.
4 M100E.
5 M100E H.
6 M100E U.
10
O2 option.
11 CO 2 option.
05928 Rev F.0B
A-23
DCN 5063
PRINTED DOCUMENTS ARE UNCONTROLLED
Download from Www.Somanuals.com. All Manuals Search And Download.
TELEDYNE INSTRUMENTS
Model 100EU Instruction Manual
APPENDIX A - Version Specific Software Documentation
APPENDIX A-4: M100Eu Signal I/O Definitions, Revision F.0B
Table A-4: M100EU Signal I/O Definitions, Revision F.0B
Signal Name
Bit or Channel
Number
Description
Internal inputs, U7, J108, pins 9–16 = bits 0–7, default I/O address 322 hex
0–7
Spare
AUX board digital outputs, default I2C address 30 hex
ELEC_TEST 3
OPTIC_TEST 3
DARK_TEST 3
PREAMP_RANGE_HI 3
0
1
2
3
1 = electrical test on
0 = off
1 = optic test on
0 = off
1 = dark test on
0 = off
1 = select high preamp range
0 = select low range
Internal outputs, U8, J108, pins 1–8 = bits 0–7, default I/O address 322 hex
ELEC_TEST
0
1
2
1 = electrical test on
0 = off
OPTIC_TEST
1 = optic test on
0 = off
PREAMP_RANGE_HI
1 = select high preamp range
0 = select low range
Spare
3–5
I2C_RESET
6
7
1 = reset I2C peripherals
0 = normal
I2C_DRV_RST
0 = hardware reset 8584 chip
1 = normal
Control inputs, U11, J1004, pins 1–6 = bits 0–5, default I/O address 321 hex
EXT_ZERO_CAL
EXT_SPAN_CAL
EXT_LOW_SPAN 2, 6
0
1
2
0 = go into zero calibration
1 = exit zero calibration
0 = go into span calibration
1 = exit span calibration
0 = go into low span calibration
1 = exit low span calibration
Spare
3–5
6–7
Always 1
Control inputs, U14, J1006, pins 1–6 = bits 0–5, default I/O address 325 hex
0–5
6–7
Spare
Always 1
Control outputs, U17, J1008, pins 1–8 = bits 0–7, default I/O address 321 hex
0–7
Spare
A-24
05928 Rev F.0B
DCN 5063
PRINTED DOCUMENTS ARE UNCONTROLLED
Download from Www.Somanuals.com. All Manuals Search And Download.
TELEDYNE INSTRUMENTS
APPENDIX A - Version Specific Software Documentation
Model 100EU Instruction Manual
Control outputs, U21, J1008, pins 9–12 = bits 0–3, default I/O address 325 hex
Spare
Alarm outputs, U21, J1009, pins 1–12 = bits 4–7, default I/O address 325 hex
0–3
ST_SYSTEM_OK2,
MB_RELAY_36 9
4
1 = system OK
0 = any alarm condition or in diagnostics mode
Controlled by MODBUS coil register
Controlled by MODBUS coil register
Controlled by MODBUS coil register
Controlled by MODBUS coil register
MB_RELAY_37 9
MB_RELAY_38 9
MB_RELAY_39 9
5
6
7
A status outputs, U24, J1017, pins 1–8 = bits 0–7, default I/O address 323 hex
ST_SYSTEM_OK
ST_CONC_VALID
0
0 = system OK
1 = any alarm condition
0 = conc. valid
1
1 = warnings or other conditions that affect validity of
concentration
ST_HIGH_RANGE
ST_ZERO_CAL
ST_SPAN_CAL
2
3
4
0 = high auto-range in use
1 = low auto-range
0 = in zero calibration
1 = not in zero
0 = in span calibration
1 = not in span
ST_DIAG_MODE 5
0 = in diagnostic mode
1 = not in diagnostic mode
ST_LOW_SPAN_CAL 2, 6
6
0 = in low span calibration
1 = not in low span
Spare
7
B status outputs, U27, J1018, pins 1–8 = bits 0–7, default I/O address 324 hex
ST_LAMP_ALARM
ST_DARK_CAL_ALARM
ST_FLOW_ALARM
ST_PRESS_ALARM
ST_TEMP_ALARM
ST_HVPS_ALARM
ST_CO2_CAL 11
0
1
2
3
4
5
6
7
0 = lamp intensity low
1 = lamp intensity OK
0 = dark cal. warning
1 = dark cal. OK
0 = any flow alarm
1 = all flows OK
0 = any pressure alarm
1 = all pressures OK
0 = any temperature alarm
1 = all temperatures OK
0 = HVPS alarm
1 = HVPS OK
0 = in CO2 calibration
1 = not in CO2 calibration
0 = in O2 calibration
1 = not in O2 calibration
ST_O2_CAL 10
Front panel I2C keyboard, default I2C address 4E hex
05928 Rev F.0B
DCN 5063
A-25
PRINTED DOCUMENTS ARE UNCONTROLLED
Download from Www.Somanuals.com. All Manuals Search And Download.
TELEDYNE INSTRUMENTS
Model 100EU Instruction Manual
APPENDIX A - Version Specific Software Documentation
MAINT_MODE
LANG2_SELECT
SAMPLE_LED
CAL_LED
5 (input)
0 = maintenance mode
1 = normal mode
0 = select second language
1 = select first language (English)
0 = sample LED on
1 = off
6 (input)
8 (output)
9 (output)
10 (output)
14 (output)
0 = cal. LED on
1 = off
FAULT_LED
0 = fault LED on
1 = off
AUDIBLE_BEEPER
0 = beeper on (for diagnostic testing only)
1 = off
Relay board digital output (PCF8575), default I2C address 44 hex
RELAY_WATCHDOG 0
RCELL_HEATER
Alternate between 0 and 1 at least every 5 seconds to keep
relay board active
0 = reaction cell heater on
1 = off
1
2–3
Spare
IZS_HEATER
4
0 = IZS heater on
1 = off
O2_CELL_HEATER 10
CAL_VALVE
5
0 = O2 sensor cell heater on
1 = off
6
0 = let cal. gas in
1 = let sample gas in
0 = let span gas in
1 = let zero gas in
0 = let low span gas in
1 = let sample gas in
0 = open pressurized span inlet valve
1 = close valve
SPAN_VALVE
7
LOW_SPAN_VALVE 2, 6
CYLINDER_VALVE 7
ZERO_VALVE 2
DARK_SHUTTER
11–
8
8
9
0 = let zero gas in
1 = let sample gas in
0 = close dark shutter
1 = open
10
15
Spare
AUX board analog inputs, default I2C address 30 hex
PMT_SIGNAL 3
0 (register number)
PMT detector
UVLAMP_SIGNAL 3
NORM_PMT_SIGNAL 3
1
2
UV lamp intensity
Normalized PMT detector
PMT temperature
PMT_TEMP 3
3
HVPS_VOLTAGE 3
PMT_DARK 3
LAMP_DARK 3
4
5
6
HV power supply output
PMT reading during dark cycles
Lamp reading during dark cycles
A-26
05928 Rev F.0B
DCN 5063
PRINTED DOCUMENTS ARE UNCONTROLLED
Download from Www.Somanuals.com. All Manuals Search And Download.
TELEDYNE INSTRUMENTS
APPENDIX A - Version Specific Software Documentation
Model 100EU Instruction Manual
AGND_DARK 3
AGND_LIGHT 3
VREF_DARK 3
VREF_LIGHT 3
7
AGND reading during dark cycles
AGND reading during light cycles
VREF4096 reading during dark cycles
VREF4096 reading during light cycles
8
9
10
Rear board primary MUX analog inputs
PMT detector
1
HVPS_VOLTAGE
PMT_TEMP 2
UVLAMP_SIGNAL
4
HV power supply output
PMT temperature
3
5
UV lamp intensity
Temperature MUX
PHOTO_ABS 8
Pre-amplified UV lamp intensity
O2 concentration sensor
Sample pressure
O2_SENSOR 10
6
SAMPLE_PRESSURE 7
TEST_INPUT_8
8
Diagnostic test input
4.096V reference from MAX6241
Sample flow rate
REF_4096_MV
9
SAMPLE_FLOW
10
VACUUM_PRESSURE 2 10
CO2_SENSOR 11 11
Vacuum pressure
CO2 concentration sensor
Spare (thermocouple input?)
DAC MUX
12–13
14
REF_GND 15
Ground reference
Rear board temperature MUX analog inputs
BOX_TEMP
RCELL_TEMP
IZS_TEMP 2
3
0
1
Internal box temperature
Reaction cell temperature
IZS temperature
Spare
O2_CELL_TEMP 10
TEMP_INPUT_5
TEMP_INPUT_6
7
4
O2 sensor cell temperature
Diagnostic temperature input
Diagnostic temperature input
Spare
5
6
Rear board DAC MUX analog inputs
DAC_CHAN_1
DAC_CHAN_2
DAC_CHAN_3
DAC_CHAN_4
0
1
2
3
DAC channel 0 loopback
DAC channel 1 loopback
DAC channel 2 loopback
DAC channel 3 loopback
Rear board analog outputs
CONC_OUT_1,
DATA_OUT_1
CONC_OUT_2,
DATA_OUT_2
CONC_OUT_3 10,
DATA_OUT_3
0
1
2
Concentration output #1 (SO2, range #1),
Data output #1
Concentration output #2 (SO2, range #2),
Data output #2
Concentration output #3 (CO2 or O2),
Data output #3
05928 Rev F.0B
DCN 5063
A-27
PRINTED DOCUMENTS ARE UNCONTROLLED
Download from Www.Somanuals.com. All Manuals Search And Download.
TELEDYNE INSTRUMENTS
Model 100EU Instruction Manual
APPENDIX A - Version Specific Software Documentation
TEST_OUTPUT,
DATA_OUT_4
3
Test measurement output,
Data output #4
I2C analog output (AD5321), default I2C address 18 hex
LAMP_POWER 5
1 Optional.
0
Lamp power (0–5V)
2 M100E H.
3 M100E U.
4 M100EF
.
5
Engineering firmware only.
Low span option.
6
7
Pressurized span option.
8 M100E.
9 MODBUS
option.
10
O2 option.
11 CO 2 option.
A-28
05928 Rev F.0B
DCN 5063
PRINTED DOCUMENTS ARE UNCONTROLLED
Download from Www.Somanuals.com. All Manuals Search And Download.
TELEDYNE INSTRUMENTS
APPENDIX A - Version Specific Software Documentation
Model 100EU Instruction Manual
M100E MODBUS Register Map
MODBUS
Description
Units
Register Address
(dec., 0-based)
MODBUS Floating Point Input Registers
(32-bit IEEE 754 format; read in high-word, low-word order; read-only)
0
2 1
PMT detector reading
mV
mV
mV
%
Pre-amplified UV lamp intensity reading
UV lamp intensity reading
UV lamp ratio of calibrated intensity
electrical offset
4
6
8 PMT
10
mV
mV
—
UV lamp electrical offset
2 slope for range #1
12 SO
14 SO
16 SO
18 SO
20
2 slope for range #2
—
2 offset for range #1
mV
mV
PPB,
PPM 2
PPB
2 offset for range #2
SO2 concentration for range #1 during zero/span calibration, just
before computing new slope and offset
22
SO2 concentration for range #2 during zero/span calibration, just
before computing new slope and offset
24 SO
26 SO
28 12 SO
30 12 SO
32 Conc
34
2 concentration for range #1
2 concentration for range #2
2 concentration for range #1, with O2 correction
2 concentration for range #2, with O2 correction
entration stability
PPB
PPB
PPB
PPB
PPB
PPB
C
Stray light reading
36
Reaction cell temperature
S temperature
38 1 IZ
40 PMT
42 1, 2 Sample
44 Sampl
46 2 Vacuum
48
C
temperature
C
flow
cc/m
“Hg
“Hg
C
e pressure
pressure
Internal box temperature
High voltage power supply output
Diagnostic test input (TEST_INPUT_8)
Diagnostic temperature input (TEMP_INPUT_5)
Diagnostic temperature input (TEMP_INPUT_6)
Ground reference (REF_GND)
4096 mV reference (REF_4096_MV)
O2 concentration
50
Volts
mV
C
52
54
56
C
58
mV
mV
%
60
100 10
05928 Rev F.0B
DCN 5063
A-29
PRINTED DOCUMENTS ARE UNCONTROLLED
Download from Www.Somanuals.com. All Manuals Search And Download.
TELEDYNE INSTRUMENTS
Model 100EU Instruction Manual
APPENDIX A - Version Specific Software Documentation
102 10
O2 concentration during zero/span calibration, just before computing
%
new slope and offset
104 10
106 10
108 10
200 11 CO
202 11
O2 slope
—
%
C
%
O2 offset
O2 sensor cell temperature
2 concentration
CO2 concentration during zero/span calibration, just before
computing new slope and offset
%
204 11 CO
206 11 CO
2 slope
—
%
2 offset
MODBUS Floating Point Holding Registers
(32-bit IEEE 754 format; read/write in high-word, low-word order; read/write)
0 Maps
to SO2_SPAN1 variable; target conc. for range #1
to SO2_SPAN2 variable; target conc. for range #2
to O2_TARG_SPAN_CONC variable
Conc. units
2 Maps
Conc. units
100 10 Maps
200 11 Maps
%
%
to CO2_TARG_SPAN_CONC variable
MODBUS Discrete Input Registers
(single-bit; read-only)
0
PMT detector warning
1 UV
2 Dark
3 1 IZ
4 Box
5 PMT
6
detector warning
calibration warning
S temperature warning
temperature warning
temperature warning
Reaction cell temperature warning
e flow warning
7 Sampl
8 Sampl
9 2 Vacuum
10 HVPS
11
e pressure warning
pressure warning
warning
System reset warning
12
Rear board communication warning
y board communication warning
Front panel communication warning
og calibration warning
13 Rela
14
15 Anal
16 D
17 D
18 Invali
19
ynamic zero warning
ynamic span warning
d concentration
In zero calibration mode
In low span calibration mode
In span calibration mode
In multi-point calibration mode
In Hessen manual mode
System is OK (same meaning as SYSTEM_OK I/O signal)
20 2
21
22
23
24
A-30
05928 Rev F.0B
DCN 5063
PRINTED DOCUMENTS ARE UNCONTROLLED
Download from Www.Somanuals.com. All Manuals Search And Download.
TELEDYNE INSTRUMENTS
APPENDIX A - Version Specific Software Documentation
Model 100EU Instruction Manual
100 10 In
101 10
200 11 In
O2 calibration mode
O2 cell temperature warning
CO2 calibration mode
MODBUS Coil Registers
(single-bit; read/write)
0
Maps to relay output signal 36 (MB_RELAY_36 in signal I/O list)
Maps to relay output signal 37 (MB_RELAY_37 in signal I/O list)
Maps to relay output signal 38 (MB_RELAY_38 in signal I/O list)
Maps to relay output signal 39 (MB_RELAY_39 in signal I/O list)
Triggers zero calibration of range #1 (on enters cal.; off exits cal.)
Triggers span calibration of range #1 (on enters cal.; off exits cal.)
Triggers zero calibration of range #2 (on enters cal.; off exits cal.)
Triggers span calibration of range #2 (on enters cal.; off exits cal.)
1
2
3
20 13
21 13
22 13
23 13
1 M100E.
2 M100E H.
10
O2 option.
11 CO 2 option.
12 SO 2 with O2 correction option.
13 Set DYN_ZERO or DYN_SPAN variables to ON to enable calculating new slope or offset. Otherwise a calibration check
is performed.
05928 Rev F.0B
DCN 5063
A-31
PRINTED DOCUMENTS ARE UNCONTROLLED
Download from Www.Somanuals.com. All Manuals Search And Download.
TELEDYNE INSTRUMENTS
Model 100EU Instruction Manual
APPENDIX A - Version Specific Software Documentation
APPENDIX A-5: M100EU iDAS Functions, Revision F.0B
Table A-5: M100EU DAS Trigger Events, Revision F.0B
Name
Description
ATIMER
Automatic timer expired
EXITZR
EXITLS 2, 3
Exit zero calibration mode
Exit low span calibration mode
Exit high span calibration mode
EXITHS
EXITMP
Exit multi-point calibration mode
Exit O2 calibration mode
EXITO2 10
SLPCHG
CO2SLC 11
O2SLPC 10
EXITDG
Slope and offset recalculated
CO2 slope and offset recalculated
O2 slope and offset recalculated
Exit diagnostic mode
PMTDTW
UVLMPW
DRKCLW 1
RCTMPW
O2TMPW 10
IZTMPW 1
PTEMPW
SFLOWW
SPRESW
VPRESW 2
BTEMPW
HVPSW
PMT detector warning
UV lamp warning
Dark calibration warning
Reaction cell temperature warning
O2 sensor cell temperature warning
IZS temperature warning
PMT temperature warning
Sample flow warning
Sample pressure warning
Vacuum pressure warning
Box temperature warning
High voltage power supply warning
1 M100E.
2 M100E H.
3
Low span option.
10
O2 option.
11 CO 2 option.
Table A-6: M100EU iDAS Functions, Revision F.0B
Name
PMTDET
PHABS 1
UVDET
Description
PMT detector reading
Units
mV
mV
mV
%
Pre-amplified UV lamp intensity reading
UV lamp intensity reading
LAMPR
UV lamp ratio of calibrated intensity
PMT electrical offset
DRKPMT
DARKUV
SLOPE1
mV
mV
—
UV lamp electrical offset
SO2 slope for range #1
A-32
05928 Rev F.0B
DCN 5063
PRINTED DOCUMENTS ARE UNCONTROLLED
Download from Www.Somanuals.com. All Manuals Search And Download.
TELEDYNE INSTRUMENTS
APPENDIX A - Version Specific Software Documentation
Model 100EU Instruction Manual
SLOPE2
SO2 slope for range #2
—
OFSET1
SO2 offset for range #1
SO2 offset for range #2
CO2 slope
mV
mV
—
OFSET2
CO2SLP 11
CO2OFS 11
O2SLPE 10
O2OFST 10
ZSCNC1
CO2 offset
%
O2 slope
—
O2 offset
%
SO2 concentration for range #1 during zero/span calibration, just
before computing new slope and offset
PPB,
PPM 2
PPB
ZSCNC2
SO2 concentration for range #2 during zero/span calibration, just
before computing new slope and offset
CO2ZSC 11
O2ZSCN 10
CO2 concentration during zero/span calibration, just before
computing new slope and offset
%
%
O2 concentration during zero/span calibration, just before computing
new slope and offset
CONC1
SO2 concentration for range #1
SO2 concentration for range #2
SO2 concentration for range #1, with O2 correction
SO2 concentration for range #2, with O2 correction
CO2 concentration
PPB
PPB
PPB
PPB
%
CONC2
SO2CR1 12
SO2CR2 12
CO2CNC 11
O2CONC 10
STABIL
STABL2 3
STABUV 3
STRLGT
RCTEMP
O2TEMP 10
IZSTMP 1
PMTTMP
SMPFLW 1, 2
SMPPRS
VACUUM 2
BOXTMP
HVPS
O2 concentration
%
Concentration stability #1
PPB
PPB
mV
PPB
C
Concentration stability #2
UV lamp stability
Stray light reading
Reaction cell temperature
O2 sensor cell temperature
IZS temperature
C
C
PMT temperature
C
Sample flow
cc/m
“Hg
“Hg
C
Sample pressure
Vacuum pressure
Internal box temperature
High voltage power supply output
Diagnostic test input (TEST_INPUT_8)
Diagnostic temperature input (TEMP_INPUT_5)
Diagnostic temperature input (TEMP_INPUT_6)
Ground reference (REF_GND)
4096 mV reference (REF_4096_MV)
AGND reading during dark cycles
AGND reading during light cycles
VREF4096 reading during dark cycles
VREF4096 reading during light cycles
Volts
mV
C
TEST8
TEMP5
TEMP6
C
REFGND
RF4096
AGNDDK 3
AGNDLT 3
RF4VDK 3
RF4VLT 3
mV
mV
mV
mV
mV
mV
05928 Rev F.0B
DCN 5063
A-33
PRINTED DOCUMENTS ARE UNCONTROLLED
Download from Www.Somanuals.com. All Manuals Search And Download.
TELEDYNE INSTRUMENTS
Model 100EU Instruction Manual
APPENDIX A - Version Specific Software Documentation
1 M100E.
2 M100E H.
3 M100E U.
10
O2 option.
11 CO 2 option.
12 SO 2 with O2 correction option.
A-34
05928 Rev F.0B
PRINTED DOCUMENTS ARE UNCONTROLLED
DCN 5063
Download from Www.Somanuals.com. All Manuals Search And Download.
TELEDYNE INSTRUMENTS
APPENDIX A - Version Specific Software Documentation
Model 100EU Instruction Manual
APPENDIX A-6: Terminal Command Designators, Revision F.0B
Table A-7: Terminal Command Designators, Revision F.0B
COMMAND A
? [ID]
DDITIONAL COMMAND SYNTAX
DESCRIPTION
Display help screen and this list of commands
Establish connection to instrument
Terminate connection to instrument
Display test(s)
LOGON [ID]
LOGOFF [ID]
Password
SET ALL|name|hexmask
LIST [ALL|name|hexmask] [NAMES|HEX]
Name
Print test(s) to screen
Print single test
T [ID]
CLEAR ALL|name|hexmask
SET ALL|name|hexmask
LIST [ALL|name|hexmask] [NAMES|HEX]
name
Disable test(s)
Display warning(s)
Print warning(s)
W [ID]
Clear single warning
CLEAR ALL|name|hexmask
ZERO|LOWSPAN|SPAN [1|2]
ASEQ number
Clear warning(s)
Enter calibration mode
Execute automatic sequence
Compute new slope/offset
Exit calibration mode
C [ID]
COMPUTE ZERO|SPAN
EXIT
ABORT
Abort calibration sequence
Print all I/O signals
LIST
name[=value]
Examine or set I/O signal
Print names of all diagnostic tests
Execute diagnostic test
Exit diagnostic test
LIST NAMES
ENTER name
EXIT
RESET [DATA] [CONFIG] [exitcode] Reset
PRINT ["name"] [SCRIPT]
RECORDS ["name"]
instrument
D [ID]
Print iDAS configuration
Print number of iDAS records
REPORT ["name"] [RECORDS=number]
[FROM=<start date>][TO=<end
date>][VERBOSE|COMPACT|HEX] (Print DAS
records)(date format: MM/DD/YYYY(or YY)
[HH:MM:SS]
Print iDAS records
CANCEL
Halt printing iDAS records
Print setup variables
LIST
name[=value [warn_low [warn_high]]]
Modify variable
name="value"
CONFIG
Modify enumerated variable
Print instrument configuration
Enter/exit maintenance mode
Print current instrument mode
V [ID]
MAINT ON|OFF
MODE
DASBEGIN [<data channel definitions>]
DASEND
Upload iDAS configuration
CHANNELBEGIN propertylist CHANNELEND
CHANNELDELETE ["name"]
Upload single iDAS channel
Delete iDAS channels
05928 Rev F.0B
DCN 5063
A-35
PRINTED DOCUMENTS ARE UNCONTROLLED
Download from Www.Somanuals.com. All Manuals Search And Download.
TELEDYNE INSTRUMENTS
Model 100EU Instruction Manual
APPENDIX A - Version Specific Software Documentation
The command syntax follows the command type, separated by a space character. Strings in [brackets] are
optional designators. The following key assignments also apply.
TERMINAL KEY ASSIGNMENTS
ESC Abort
CR (ENTER)
Ctrl-C
line
Execute command
Switch to computer mode
COMPUTER MODE KEY ASSIGNMENTS
LF (line feed)
Ctrl-T
Execute command
Switch to terminal mode
USER NOTES:
A-36
05928 Rev F.0B
DCN 5063
PRINTED DOCUMENTS ARE UNCONTROLLED
Download from Www.Somanuals.com. All Manuals Search And Download.
MODEL M100EU INSTRUCTION MANUAL
Appendix B - Spare Parts Lists
APPENDIX B - SPARE PARTS LISTS
• 053600100 – M100EU Spare Parts List
• 059460000 – M100EU Recommended Spares Stocking Levels
05929 Rev A
B-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B - Spare Parts Lists
MODEL M100EU INSTRUCTION MANUAL
B-2
05929 Rev. A
Download from Www.Somanuals.com. All Manuals Search And Download.
M100EU Spare Parts List
Part Number
000940100
Description
ORIFICE, 3 MIL, IZS
000940800
002690000
002700000
002720000
003290000
005960000
009690200
009690300
013140000
013210000
013390000
013400000
013420000
013570000
014400100
014750000
016290000
016300700
037860000
040010000
040030100
041710000
042410200
042580000
042900100
043570000
043940000
044670000
045150100
045230200
046250000
046260000
048620200
048830000
049310100
050610100
050610200
050610300
050610400
050630200
051990000
052660000
054340000
054650000
055100200
ORIFICE, 012 MIL, RXCELL
LENS, UV
LENS, PMT
FILTER, PMT OPTICAL, 330 NM
ASSY, THERMISTOR
AKIT, EXPEND, 6LBS ACT CHARCOAL
AKIT, TFE FLTR (FL19) ELEM, 47MM, (100)
AKIT, TFE FLTR ELEMENT, 47MM, 1UM (30)
ASSY, COOLER FAN (NOX/SOX)
ASSY, VACUUM MANIFOLD, M100A/E
ASSY, KICKER, M100A/E
PMT, SO2, M100A/E
ASSY, ROTARY SOLENOID, M100A/E/U/H
ASSY, THERMISTOR (COOLER)
OPTION, ZERO AIR SCRUBBER, M100E
AKIT, EXP KIT, M100A/M100E, IZS
WINDOW, SAMPLE FILTER, 47MM (KB)
ASSY, SAMPLE FILTER, 47MM, ANG BKT (KB)
ORING, TFE RETAINER, SAMPLE FILTER
ASSY, FAN REAR PANEL, E SERIES
PCA, FLOW/PRESSURE
ASSY, CPU, CONFIGURATION, "E" SERIES *
ASSY, PUMP, INT, E SERIES
PCA, KEYBOARD, E-SERIES, W/V-DETECT
PROGRAMMED FLASH, E SERIES
AKIT, EXPENDABLES, M100E/M101E/M108E
PCA, INTERFACE, ETHERNET, E-SERIES
PCA, ANALOG OUTPUT ISOLATOR, E SERIES
MANUAL, OPERATION, M100E
PCA, RELAY CARD W/RELAYS, E SERIES, S/N'S >455
ASSY, RXCELL HEATER/FUSE, M100E
ASSY, THERMISTOR, RXCELL, M100E (KB)
PCA, SERIAL INTERFACE, w/ MD, E SERIES
AKIT, EXP KIT, EXHAUST CLNSR, SILCA GEL
PCA, TEC CONTROL, E SERIES
CONFIGURATION PLUGS, 115V/60Hz
CONFIGURATION PLUGS, 115V/50Hz
CONFIGURATION PLUGS, 220-240V/50Hz
CONFIGURATION PLUGS, 220-240V/60Hz
PCA, REF DET w/OP20, DUAL OUT, M100EU
ASSY, SCRUBBER, INLINE EXHAUST, DISPOS
ASSY, HEATER/THERMISTOR (IZS)
PCA, PRECISION INT. PMT PREAMP, M100EU
PCA, SYNC/DEMOD, M100EU
OPTION, PUMP ASSY, 240V *
0536001F - M100EU SPL (DCN5013)
Page 1 of 2
09/17/08
Download from Www.Somanuals.com. All Manuals Search And Download.
M100EU Spare Parts List
Part Number
055560000
Description
ASSY, VALVE, VA59 W/DIODE, 5" LEADS
055920000
055930100
056080000
058020100
059200000
061930200
CN0000458
CN0000520
ASSY, SO2 SENSOR, M100EU (KB)
DOC, W/SOFTWARE, M100EU
ASSY, HVPS, M100EU PMT
PCA, E-SERIES MOTHERBOARD, GEN 5
ASSY, UV LAMP, M100EU
PCA, 100EU, UV LAMP DRIVER, GEN-2
CONNECTOR, REAR PANEL, 12 PIN
CONNECTOR, REAR PANEL, 10 PIN
DS0000025
FL0000001
FL0000003
FM0000004
HW0000005
HW0000020
HW0000036
KIT000093
KIT000095
KIT000219
KIT000253
KIT000254
OP0000031
OR0000001
OR0000004
OR0000006
OR0000007
OR0000015
OR0000016
OR0000025
OR0000027
OR0000039
OR0000046
OR0000083
OR0000084
OR0000094
PU0000022
RL0000015
SW0000051
SW0000059
WR0000008
DISPLAY, E SERIES (KB)
FILTER, SS
FILTER, DFU
FLOWMETER (KB)
FOOT, CHASSIS
SPRING
TFE TAPE, 1/4" (48 FT/ROLL)
REPLACEMENT KIT, 214NM FLTR (03187)
AKIT, REPLACEMENT COOLER, A/E SERIES
KIT, 4-20MA CURRENT OUTPUT (E SERIES)
KIT, SPARE PS37, E SERIES
KIT, SPARE PS38, E SERIES
WINDOW, QUARTZ, REF DETECTOR
ORING, FLOW CONTROL/IZS
ORING, OPTIC/CELL, CELL/TRAP
ORING, CELL/PMT
ORING, PMT/BARREL/CELL
ORING, PMT FILTER
ORING, UV LENS
ORING, ZERO AIR SCRUBBER
ORING, COLD BLOCK/PMT HOUSING & HEATSINK
ORING, QUARTZ WINDOW/REF DETECTOR
ORING, PERMEATION OVEN
ORING, PMT SIGNAL & OPTIC LED
ORING, UV FILTER
ORING, SAMPLE FILTER
KIT, PUMP REBUILD
RELAY, DPDT, (KB)
SWITCH, POWER, CIRC BR
PRESSURE SENSOR, 0-15 PSIA, ALL SEN
POWER CORD, 10A
0536001F - M100EU SPL (DCN5013)
Page 2 of 2
09/17/08
Download from Www.Somanuals.com. All Manuals Search And Download.
Teledyne Advanced Pollution Instrumentation
RECOMMENDED SPARE PARTS STOCKING LEVELS
Model 100EU
UNITS
PART NO
DESCRIPTION
1
2-5 6-10 11-20 21-30
000940800
002720000
013140000
013400000
014080100
014610000
040010000
040030100
041710000
042410400
042580000
045230200
050630200
054340000
054650000
054710000
055120200
057020100
DS0000025
Orifice, 12 Mil
Filter, 330 NM
Cooler Fan
PMT, SO2
Assy, HVPS, NOX/SOX
1
2
1
2
4
2
4
1
4
3
4
1
1
1
4
4
1
1
1
2
2
1
1
4
2
2
1
1
1
Kit, Replacement Cooler
Assy, Fan, Rear Panel, E Series
PCA, Press Sensors (1X), Flow, E Series
CPU, Configuration E Series
Assy, Pump, Internal, E Series, 115/240V
PCA, Keyboard
PCA, Relay Board w/Diode Protection
PCA, M100EU UV Ref Det, Dual Out
PCA, Prescision INT, PMT Preamp
PCA, Sync/Demod
1
1
1
2
2
4
4
1
1
1
1
1
1
4
2
1
1
1
Assy, UV Lamp, M100E
1
1
2
1
PCA, Bursting UV Driver, M100EU
PCA, Motherboard, E Series, GEN 4
Display
IZS/ZS Option
055560000
ASSY, VALVE, VA59 W/DIODE, E-SERIES
1
2
2
4
05946A
3/13/2007
Download from Www.Somanuals.com. All Manuals Search And Download.
THIS PAGE IS INTENTIONALLY LEFT BLANK
Download from Www.Somanuals.com. All Manuals Search And Download.
Model 100EU Instruction Manual Addendum
Appendix C – Warranty Repair Questionnaire
Appendix C – Warranty Repair Questionnaire
CUSTOMER: _________________________________ PHONE: __________________________________________________
CONTACT NAME: ____________________________ FAX NO. __________________________________________________
SITE ADDRESS: _________________________________________________________________________________________
MODEL 100EU SERIAL NO.: ___________________ FIRMWARE REVISION: _____________________________________
1. ARE THERE ANY FAILURE MESSAGES? _______________________________________________________________
________________________________________________________________________________________________________
________________________________________________________________________________________________________
2. PLEASE COMPLETE THE FOLLOWING TABLE: (NOTE: DEPENDING ON OPTIONS INSTALLED, NOT ALL TEST
PARAMETERS BELOW WILL BE AVAILABLE IN YOUR INSTRUMENT)
Parameter
Recorded Value
PPB/PPM
Acceptable Value
*IF OPTION IS INSTALLED
RANGE
STABIL
STABIL2
PPB
PPB
IN-HG-A
cm3/MIN
mV
≤0.3 PPB WITH ZERO AIR
<= 1 PPB WITH ZERO AIR
AMBIENT (- 2) IN-HG-A
650 ± 10%
PRESS
SAMPLE FLOW
PMT SIGNAL WITH
ZERO AIR
-20 TO 150 mV
PMT SIGNAL AT
SPAN GAS CONC
NORM PMT AT SPAN
GAS CONC
UV LAMP
mV
PPB/PPM
mV
0-5000 mV
0-20000 PPB
0-5000 mV
PPB/PPM
0-20000 PPB
2000 TO 4000 mV
< 15mV
mV
mV
UV STAB
LAMP RATIO
STR. LGT
DARK PMT
DARK LAMP
SLOPE
mV
PPB
mV
mV
30 TO 120%
≤ 100 PPB/ ZERO AIR
200-325
-50 TO 200 mV
1.0 ± 0.5
OFFSET
mV
< 250 mV
HVPS
V
≈ 400 – 800
RCELL TEMP
BOX TEMP
PMT TEMP
IZS TEMP*
ETEST
ºC
ºC
ºC
ºC
mV
mV
50ºC ± 1
AMBIENT ± 5
9.5ºC ± 2º CONSTANT
50ºC ± 1
2000 mV ± 500
2000 mV ± 1000
OTEST
Values are in the Signal I/O
REF_4096_MV
REF_GND
mV
mV
4096mv±2mv and Must be Stable
0± 0.5 and Must be Stable
05930 Rev A
C-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Model 100EU Instruction Manual Addendum
Appendix C – Warranty Repair Questionnaire
3. WHAT IS THE SAMPLE FLOW & SAMPLE PRESSURE W/SAMPLE INLET ON REAR OF MACHINE CAPPED?
SAMPLE FLOW - CC SAMPLE PRESS - IN-HG-A
4. WHAT ARE THE FAILURE SYMPTOMS? ______________________________________________________________
_______________________________________________________________________________________________________
5. IF POSSIBLE, PLEASE INCLUDE A PORTION OF A STRIP CHART PERTAINING TO THE PROBLEM. CIRCLE
PERTINENT DATA.
6. THANK YOU FOR PROVIDING THIS INFORMATION. YOUR ASSISTANCE ENABLES TELEDYNE API TO
RESPOND FASTER TO THE PROBLEM THAT YOU ARE ENCOUNTERING.
C-2
05930 Rev. A
Download from Www.Somanuals.com. All Manuals Search And Download.
M100EU Manual Addendum
Appendix D – Schematic List
Appendix D – Schematic List
Table D-1: List of Included Electronic Schematics
DOCUMENT TITLE
DOCUMENT #
0506402
05435
M100EU UV Ref PCA
M100EU Internal PMT Preamp PCA
M100EU Sync/Demod PCA
05466
0591602
M100EU Bursting UV Lamp Driver
Other schematics can be found in the M100E Operators Manual (04145).
05931 Rev A
D-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix D – Schematic List
M100EU Manual Addendum
D-2
05931 Rev. A
Download from Www.Somanuals.com. All Manuals Search And Download.
|