LV148EA/LV148XA LV156EA/LV156XA
LV195EA/LV195XA (LEV90-120)
Four-Cycle Engine • Vertical Crankshaft • Air-Cooled
Table of Contents
VII. Maintenance .................................................................................. 13
Register Your TecumsehPower Engine
Maintenance Tips
On-Line Store
Locate your nearest TecumsehPower Servicing Dealer
181-1215-14
(English) 6/01/08
Download from Www.Somanuals.com. All Manuals Search And Download.
• NEVER fill fuel tank indoors. Fill fuel tank outdoors
in a well-ventilated area.
I. General Safety Precautions
• DO NOT smoke while refueling tank.
! WARNING
• Use only an approved red GASOLINE container
to store and dispense fuel. TecumsehPower
Company recommends purchasing gasoline in
containers with a capacity of 2.5 gallons or less.
Small containers are easier to handle and help
eliminate spillage during refueling.
Read equipment manufacturer’s manual and this
material thoroughly before using this engine. Failure to
do so can result in serious injury or death. Consult your
local Authorized TecumsehPower Servicing Dealer, call
additional information.
• DO NOT pour fuel from engine or siphon fuel by
mouth. To empty the fuel tank, see "I. Draining Fuel"
instructions on page 23.
A. Avoid Carbon Monoxide Poisoning
C. Adult Supervision of Operation, Refueling
and Maintenance
All engine exhaust contains
carbon monoxide, a deadly
gas. Breathing carbon
The manufacturer of the equipment may provide
information about who is allowed to use this engine (see
equipment manufacturer’s manual). NOT everyone who is
allowed to use this engine is capable of safely and
responsibly operating, maintaining and/or fueling it.
TecumsehPower Company recommends the following:
monoxide can cause
headaches, dizziness,
drowsiness, nausea, confusion
and eventually death.
Carbon monoxide is a colorless, odorless, tasteless gas
which may be present even if you DO NOT see or smell
any engine exhaust. Deadly levels of carbon monoxide can
collect rapidly and you can quickly be overcome and
unable to save yourself. Also, deadly levels of carbon
monoxide can linger for hours or days in enclosed or
poorly-ventilated areas. If you experience any symptoms of
carbon monoxide poisoning, leave the area immediately,
get fresh air, and SEEK MEDICAL TREATMENT.
• An adult should fuel this engine. NEVER allow
children to refuel this engine. See "C. Filling Fuel
Tank" instructions on page 6.
• An adult should perform maintenance on this
engine. See "VII. Maintenance" instructions on
page 13. Only allow children to perform mainte-
nance if an adult has determined they are
experienced and capable of such operation.
To prevent serious injury or death from carbon monoxide:
• An adult should start the engine. See "G. Avoid
Accidental Starts" instructions on page 2. Only
allow children to start the engine if an adult has
determined they are experienced and capable of
such operation.
• NEVER run engine indoors. Even if you try to
ventilate engine exhaust with fans or open windows
and doors, carbon monoxide can rapidly reach
dangerous levels.
• NEVER run engine in poorly-ventilated or partially
enclosed areas such as barns, garages,
basements, carports, under dwellings, or in pits.
• To avoid unsupervised operation of the engine,
especially by children, NEVER leave it unattended
when it is running. Remove ignition key, if equipped.
• NEVER run engine outdoors where engine exhaust
can be drawn into a building through openings such
as windows and doors.
D. Stay Away from Rotating Parts
NEVER operate the engine with an unguarded engine shaft
or flywheel. See Figure 1 on page 2.
B. Avoid Gasoline Fires
The equipment manufacturer may
attach a sprocket and chain or pulley
and belt to the engine shaft. If these
parts are NOT properly guarded, or if
you are NOT sure whether they are
properly guarded, DO NOT use your
engine; contact the equipment
manufacturer. Hands, feet, hair,
jewelry, clothing, etc.,can become
entangled in rotating parts, leading to
serious injury or death. To avoid
serious injury or death, be sure the
flywheel guard is in place. See Figure
1 on page 2.
Gasoline (fuel) vapors are highly flammable
and can explode. Fuel vapors can spread
and be ignited by a spark or flame many feet
away from engine. To prevent injury or death
from fuel fires, follow these instructions:
• NEVER store engine with fuel in fuel
tank inside a building with potential
sources of ignition such as hot water and space
heaters, clothes dryers, electric motors, etc.
• NEVER remove fuel fill cap or add fuel when engine
is running.
• NEVER start or operate the engine with the fuel fill
cap removed.
• Allow engine to cool before refueling.
181-1215-14
Four-Cycle Engine • Vertical Crankshaft • Air-Cooled
Page 1
Download from Www.Somanuals.com. All Manuals Search And Download.
E. DO NOT Modify Engine
To avoid serious injury or death, DO NOT modify engine in
any way. Tampering with the governor setting can lead to a
runaway engine and cause it to operate at unsafe speeds.
NEVER tamper with factory setting of engine governor.
! WARNING
Use of this engine on fun-carts, go-karts, or mini-bikes
can result in serious injury or death. TecumsehPower
Company manufactures the Power Sport line of engines
for use in such applications. Consult your local Authorized
TecumsehPower Servicing Dealer, call 1-800-558-5402,
or visit www.TecumsehPower.com for additional information.
F. Avoid Burns and Fire from Hot Surfaces
Figure 1. Typical Flywheel Guard Location
The muffler and other engine parts become
extremely hot during operation and remain
hot after the engine has stopped.
• To avoid severe burns on contact,
STAY AWAY from hot areas of
engine. DO NOT operate the engine
without the muffler guard in place,
if equipped.
• To reduce the risk of fire keep all materials that can
burn, including grass and leaves, away from muffler
and rest of engine. DO NOT operate, idle or park
engine powered equipment in long dry grass or
other dry ground cover.
Figure 2. Disconnecting/Connecting Spark Plug
1
2
G. Avoid Accidental Starts
To prevent accidental starting when working on equipment
always:
• Carefully disconnect spark plug wire and keep it
away from spark plug. See Figures 2 and 3.
• Keep the disconnected spark plug wire
securely away from metal parts where arcing
could occur.
1. Grounding Post Connection
2. Spark Plug Connection
• Carefully attach the spark plug wire to the
grounding post, if provided.
Figure 3. Typical Grounding Post/Spark Plug Connection
• Disconnect battery at negative terminal first, if
engine is equipped with a DC electric starter.
• Turn all engine switches to “OFF” position.
• Remove ignition key, if provided.
H. Use Hearing Protection
Engine noise may cause hearing damage. Always wear
hearing protection when operating an engine.
Page 2
Four-Cycle Engine • Vertical Crankshaft • Air-Cooled
181-1215-14
Download from Www.Somanuals.com. All Manuals Search And Download.
II. How to Get Service
2083
For engine adjustments, repairs or warranty service
NOT covered in this manual, contact your nearest
Authorized TecumsehPower Servicing Dealer. Find them
TecumsehPower Company at 1-800-558-5402 for
additional information.
Register Your TecumsehPower Engine
Maintenance Tips
On-Line Store
Locate your nearest TecumsehPower Servicing Dealer
ENGINE
MODEL:
A. Engine Identification Decal
A sample engine identification decal is located in the next
column and indicates the engine’s model number,
specification and date of manufacture (DOM). See Figure 4.
SPEC:
DOM:
NOTES
Please look at the decal on your engine.
Figure 4. Engine Identification Decal
Fill in the engine information in the spaces provided for
future reference.
The engine identification decal also includes engine life
specifications for the emissions-related useful life period of
your engine. This period relates to the emission compliance
life as certified by EPA and/or CARB.
• LV models are designated as “C” 125 hours, “B” 250
hours and “A” 500 hours.
B. Technician’s Handbook
If you have a general understanding of internal combustion
engines and wish to repair and service your engine and/or
engine emission control systems yourself, a Technician’s
Handbook is available from your Authorized
TecumsehPower Servicing Dealer. See Figure 5. This
handbook covers repairs and adjustments not covered
within this Operator’s Manual, and it is intended for
individuals who have had adequate training, experience
and who practice proper tool usage. Service procedures
should be clearly understood and practiced when servicing
TecumsehPower engines.
Figure 5. Technician’s Handbook
• Order as part #692509 or #740049 for LV models.
TecumsehPower Company manufactures and is
responsible only for the engine used on this power
equipment. If repair or service is needed for anything other
than the engine, contact the service source recommended
by the equipment manufacturer.
181-1215-14
Four-Cycle Engine • Vertical Crankshaft • Air-Cooled
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
III. Oil and Fuel Specifications
A. Oil
Table 1. Recommended Oil
To operate engine you need to use a clean, high quality,
In addition, you need to be sure the oil sump contains the
correct amount of oil to operate properly.
TecumsehPower Recommended Oil Usage
Straight Grade
TecumsehPower Part No.
730225A or SAE 30W
Multi Grade
NOTES
The oil sump capacity is 21 ounces or 1-1/4 U.S. Pints
(.62 liters).
TecumsehPower Part No.
730226A or SAE 5W30 or SAE 10W
TecumsehPower
Synthetic Part No.
730263 or SAE 0W30
Be sure original container is marked A.P.I. Service “SL/SJ”.
20OF
32OF
80OF
O
O
-20 F
0OF
40OF
60OF
100 F
30OC 40OC
O
O
O
Using multigrade oil above 32°F (0°C) will increase oil
consumption. SAE 10W40 is NOT recommended.
-30 C
-20 C
-10 C
0OC
10OC
20OC
Special-formulated oils are available at your Authorized
TecumsehPower Servicing Dealer.
Table 2. Recommended Fuel
B. Fuel
Fuel Component
Percentage
Use unleaded regular, unleaded premium or reformulated
automotive fuel only. You may use gasoline containing the
components identified in Table 2.
Ethanol
10%
10%
15%
15%
Grain Alcohol (“Gasohol”)
• DO NOT use leaded fuel.
MTBE (Methyl Tertiary Butyl Ether)
ETBE (Ethyl Tertiary Butyl Ether)
• Fuel must be fresh and clean. NEVER use fuel left
over from last season or stored for long periods.
• NEVER mix oil with fuel.
• DO NOT use fuel containing Methanol
(Wood Alcohol).
The use of alternative fuels such as E85
or E20 are NOT recommended for use in
CAUTION
TecumsehPower engines. Alternative fuels with high
alcohol content can cause hard starting, poor engine
performance, and may cause internal engine damage.
Fill Between
“FULL” and “ADD”
Marks
FULL
NOTE
Damage and/or performance problems that occur from use
of fuels other than those listed in the Operator’s Manuals will
not be considered warranty.
OK
ADD
IV. Before Starting Your Engine
A. Checking Oil Level
To avoid engine damage, it is important to:
• Check oil level before each use and every 5
operating hours when engine is warm. Check oil
level more frequently during engine break-in.
Figure 6. Engine Oil Level
• Keep oil level between “FULL” and “ADD” marks on
dipstick or to point of overflow on engines without
dipstick. See Figure 6.
• Be sure oil fill cap/plug is tightened securely.
NOTES
DO NOT overfill oil filler. Doing so may result in oil
carry-over to the air cleaner and equipment and cause
malfunction or damage.
DO NOT allow oil level to fall below the “ADD” mark on
dipstick. Doing so may result in equipment malfunction or
damage.
Contact your Authorized TecumsehPower Servicing Dealer
for TecumsehPower Oil.
Page 4
Four-Cycle Engine • Vertical Crankshaft • Air-Cooled
181-1215-14
Download from Www.Somanuals.com. All Manuals Search And Download.
B. Filling Oil Sump
I. Oil Fill Cap/Dipstick
3
4
5
If your engine has an oil fill cap/dipstick go to step 1.
If your engine does NOT have an oil fill cap/dipstick,
see "II. Oil Fill Cap/Plug" instructions.
2
1. Be sure engine is upright and level.
2. Unscrew oil fill cap/dipstick from oil filler tube and wipe
3. Screw oil fill cap/dipstick back into oil filler tube.
Tighten securely.
4. Unscrew and remove oil fill cap/dipstick from oil filler
tube. Note oil level. If oil reading on dipstick is below
“ADD” mark, slowly add oil to reach “FULL” level. See
Figure 6 on page 4. Afterward, continue reading
instructions below.
7
6
1
9
8
1. Spark Plug Cap
2. Spark Plug Wire
5. Screw oil fill cap/dipstick back into oil filler tube.
Tighten securely.
3. Oil Fill Cap/Dipstick
4. Starter Cord Handle
5. Fuel Fill Cap
6. Air Cleaner
6. Wipe away any spilled oil.
NOTE
To change oil for engines with an oil fill cap/dipstick, see
"I. Oil Fill Cap/Dipstick" instructions on page 14.
7. Primer Bulb
8. Carburetor
II. Oil Fill Cap/Plug
9. Muffler
If your engine does NOT have an oil fill cap/dipstick go to
step 1. If your engine has an oil fill cap/dipstick, see "I. Oil
Figure 7. Engine With Oil Fill Cap/Dipstick
1. Be sure engine is upright and level.
3. Unscrew oil fill cap/plug.
4. Add oil to overflow point, making sure to avoid spilling.
5. Screw oil fill cap/plug back into oil fill hole.
Tighten securely.
6. Wipe away any spilled oil.
NOTE
To change oil for engines without a dipstick, see
"II. Oil Fill Cap/Plug" instructions on page 16.
Figure 8. Oil Fill Cap/Dipstick
Figure 9. Engine With Oil Fill Cap/Plug
181-1215-14
Four-Cycle Engine • Vertical Crankshaft • Air-Cooled
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
C. Filling Fuel Tank
An adult should fuel this engine.
NEVER allow children to refuel this
WARNING
Front View
engine. Gasoline (fuel) vapors are highly flammable and
can explode. Fuel vapors can spread and be ignited by a
spark or flame many feet away from engine. To prevent
injury or death from fuel fires, follow these instructions:
Bottom View
1. Stop engine and allow it to cool before refueling.
2. Be sure engine is outdoors and in a well-ventilated
area.
Figure 10. Possible Fuel Fill Cap(s)
3. Clean area around fuel fill cap and remove fuel fill cap.
See Figure 7 on page 5. Afterward, continue reading
instructions below.
Fuel
Tank
NOTE
For recommended fuel, see Table 2 and "III. Oil and Fuel
Specifications" instructions on page 4. Afterward, continue
reading instructions below.
Fuel Valve
“OPEN”
Position
Shown
4. Using an approved red GASOLINE container, add fuel
slowly, being careful to avoid spilling. DO NOT overfill
fuel tank. Leave space in the tank to allow fuel to
expand without overflowing.
Turn Valve Clockwise
To “OFF” Position
5. Replace fuel fill cap securely and wipe up spilled fuel
before starting engine. If fuel is spilled DO NOT start
engine. Move machine away from area of spillage.
Avoid creating any source of ignition until fuel vapors
are gone.
Figure 11. Fuel Valve Positions
NOTE
Replace a damaged or missing fuel fill cap only with a
genuine TecumsehPower replacement Fuel Fill Cap.
Failure to do so may VOID YOUR WARRANTY.
See Figure 10.
6. Be sure fuel valve, if present (see equipment
manufacturer’s instructions) is open. See Figure 11.
Page 6
Four-Cycle Engine • Vertical Crankshaft • Air-Cooled
181-1215-14
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 3. Engines with Electric Starters
V. Starting Your Engine
If your engine has:
Go to:
To avoid serious injury or death, an
adult should start this engine. Only
allow children to start engine if an adult has determined
they are experienced and capable of such operation.
WARNING
Primer Bulb Only
Section A.I
Section A.II
Section A.III
Choke Only
If you are unable to start this engine
Primer Bulb and Choke
WARNING
after following instructions in this
manual, contact your Authorized TecumsehPower
Servicing Dealer. To avoid serious burn injuries or damage
to your engine, DO NOT attempt to start or troubleshoot
this engine in any other way. For example:
2
3
• DO NOT use starting fluid.
• DO NOT spray flammable vapors into carburetor or
onto air cleaner.
• DO NOT put flammable liquids into carburetor or
onto air cleaner.
1
• DO NOT operate engine or pull on starter rope with
spark plug removed. Fuel can spray from spark plug
hole and ignite.
This section contains starting instructions for several
different types of engines. In order to locate the instructions
that apply to your engine, first determine what type of starter
you have. If you have an electric starter, see "A. Engines
with Electric Starters" instructions. If you have a manual
1. Electric Start Switch
2. Engine Throttle Control
3. Equipment Control
Figure 12. Typical Engine Controls
A. Engines with Electric Starters
Only one of the following three sections will apply to your
engine. See Table 3.
STOP
I. Primer Bulb Only
STOP SLOW
RUN FAST CHOKE PRIMER
1. To avoid carbon monoxide poisoning, be sure engine is
outdoors in a well-ventilated area.
Figure 13. Typical Engine Symbols
2. Move engine throttle control to “FAST” position, if
present (see equipment manufacturer’s instructions).
1
3. When starting a cold engine, press primer bulb firmly 3
times, allowing primer bulb to return completely to orig-
Afterward, continue reading instructions below.
NOTES
Be sure to cover vent hole when pressing primer bulb.
2
Cooler temperatures may require pushing primer bulb firmly
5 times.
1. Primer Bulb
2. Vent Hole
DO NOT use primer to restart a warm engine after a short
shutdown. Doing so will flood the engine and may result in
equipment malfunction.
Figure 14. Pressing Primer Bulb
4. Operate equipment control to release engine brake or
clutch, if present (see equipment manufacturer’s
instructions). See Figure 12.
181-1215-14
Four-Cycle Engine • Vertical Crankshaft • Air-Cooled
Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE
DO NOT operate an electric starter for more than 5 seconds
each attempt.
3
5. Push starter button or turn ignition switch key to start
engine.
2
6. When engine starts, release starter button or ignition
switch key.
7. If engine fails to start after 3 attempts repeat steps 2
thru 6 and try again.
8. If engine does NOT start after following steps 1 thru 7,
contact your Authorized TecumsehPower Servicing
Dealer. DO NOT attempt to start or troubleshoot this
engine in any other way.
1
7
6
5
4
1. Spark Plug Cap
2. Spark Plug Wire
3. Starter Cord Handle
4. Air Cleaner
II. Choke Only
1. To avoid carbon monoxide poisoning, be sure engine is
outdoors in a well-ventilated area.
2. Move engine throttle control to “CHOKE” or “START”
position, if present (see equipment manufacturer’s
page 7. Afterward, continue reading instructions below.
5. Primer Bulb
6. Carburetor
7. Muffler
Figure 15. Engine Components
NOTE
If restarting a warm engine after a short shutdown, move
engine throttle control to “FAST” position instead of
below.
3
2
3. Operate equipment control to release engine brake or
clutch, if present (see equipment manufacturer’s
continue reading instructions below.
1
NOTE
DO NOT operate an electric starter for more than 5 seconds
each attempt.
1. “SLOW” Position
2. “RUN” Range
3. “FAST” Position
4. Push starter button or turn ignition switch key to start
engine.
Figure 16. Start/Choke Control Positions
5. If engine fails to start after 3 attempts repeat steps 2
thru 4 and try again.
7. If engine fires but does NOT continue to run, move
engine throttle control to “FAST” position and start
engine.
6. When engine starts:
a. Release starter button or ignition switch key.
b. Move engine throttle control to “FAST” position.
8. If engine fails to start after 3 attempts in the “FAST”
position, move engine throttle control to “CHOKE”
position and start engine.
c. Next, move engine throttle control to desired speed
in “RUN” range.
9. If engine does NOT start after following steps 1 thru 8,
contact your Authorized TecumsehPower Servicing
Dealer. DO NOT attempt to start or troubleshoot this
engine in any other way.
NOTES
If engine starts but falters when engine throttle control is
moved to “FAST” position:
a. Move engine throttle control back to “CHOKE”
position.
b. Next, move engine throttle control to “FAST ”position.
If engine dies after engine throttle control is moved to
“FAST” position, repeat steps 2 thru 6 to restart engine.
Page 8
Four-Cycle Engine • Vertical Crankshaft • Air-Cooled
181-1215-14
Download from Www.Somanuals.com. All Manuals Search And Download.
III. Primer Bulb and Choke
In Temperatures Above 40°F (5°C):
2
3
Follow instructions in Section A.1. See "I. Primer Bulb
In Temperatures Below 40°F (5°C):
1. To avoid carbon monoxide poisoning, be sure engine is
outdoors in a well-ventilated area.
1
2. Move engine throttle control to “CHOKE” or “START”
position, if present (see equipment manufacturer’s
3. When starting a cold engine, press primer bulb firmly
3 times, allowing primer bulb to return completely to
instructions below.
1. Electric Start Switch
2. Engine Throttle Control
3. Equipment Control
Figure 17. Typical Engine Controls
NOTES
Be sure to cover vent hole when pressing primer bulb.
Cooler temperatures may require pushing primer bulb firmly
5 times.
STOP
STOP SLOW
RUN FAST CHOKE PRIMER
DO NOT use primer to restart a warm engine after a short
shutdown. Doing so will flood the engine and may result in
equipment malfunction.
Figure 18. Typical Engine Symbols
4. Operate equipment control to release engine brake or
clutch, if present (see equipment manufacturer’s
instructions). See Figure 17.
3
NOTE
DO NOT operate an electric starter for more than 5 seconds
each attempt.
2
5. Push starter button or turn ignition switch key to start
engine.
1
6. When engine starts:
a. Release starter button or ignition switch key.
1. “SLOW” Position
2. “RUN” Range
b. Move engine throttle control to “FAST” position.
3. “FAST” Position
c. Next, move engine throttle control to desired speed
in “RUN” range.
Figure 19. Start/Choke Control Positions
1
NOTES
If engine starts but falters when engine throttle control is
moved to “FAST” position:
a. Move engine throttle control back to “CHOKE”
b. Next, move engine throttle control to “FAST”
If engine dies after engine throttle control is moved to
“FAST” position, repeat steps 2 thru 6 to restart engine.
2
1. Primer Bulb
2. Vent Hole
Figure 20. Pressing Primer Bulb
Four-Cycle Engine • Vertical Crankshaft • Air-Cooled
181-1215-14
Page 9
Download from Www.Somanuals.com. All Manuals Search And Download.
7. If engine fires but does NOT continue to run, move
engine throttle control to “FAST” position and start
engine.
Table 4. Engines with Recoil Starters
If your engine has:
Go to:
8. If engine fails to start after 3 attempts in the “FAST”
position, move engine throttle control to “CHOKE”
position and start engine.
Primer Bulb Only
Section B.I
Section B.II
Section B.III
Choke Only
9. If engine does NOT start after following steps 1 thru 8,
contact your Authorized TecumsehPower Servicing
Dealer. DO NOT attempt to start or troubleshoot this
engine in any other way.
Primer Bulb and Choke
3
B. Engines with Recoil Starters
2
Only one of the following three sections will apply to your
engine. See Table 4.
1
I. Primer Bulb Only
1. To avoid carbon monoxide poisoning, be sure engine is
outdoors in a well-ventilated area.
2. Move engine throttle control to “FAST” position, if
present (see equipment manufacturer’s instructions).
1. Starter Cord Handle
2. Engine Throttle Control
3. Equipment Control
Figure 21. Typical Engine Controls
STOP
STOP SLOW
RUN FAST CHOKE PRIMER
Figure 22. Typical Engine Symbols
3
2
1
1. “SLOW” Position
2. “RUN” Range
3. “FAST” Position
Figure 23. Start/Choke Control Positions
Page 10
Four-Cycle Engine • Vertical Crankshaft • Air-Cooled
181-1215-14
Download from Www.Somanuals.com. All Manuals Search And Download.
3. When starting a cold engine, push primer bulb firmly 3
times, allowing primer bulb to return completely to orig-
inal position between pushes. See Figure 24.
1
NOTES
Be sure to cover vent hole when pressing primer bulb.
Cooler temperatures may require pushing primer bulb firmly
5 times.
2
DO NOT use primer to restart a warm engine after a short
shutdown. Doing so will flood the engine and may result in
equipment malfunction.
1. Primer Bulb
2. Vent Hole
4. Operate equipment control to release engine brake or
clutch, if present (see equipment manufacturer’s
continue reading instructions below.
Figure 24. Pressing Primer Bulb
When pulling starter rope, the rope
WARNING
can unexpectedly jerk back toward
engine causing serious injury. To avoid this risk, carefully
follow these instructions:
When pulling starter rope, the rope
WARNING
can unexpectedly jerk back toward
engine causing serious injury. To avoid this risk, carefully
follow these instructions:
Afterward, continue reading instructions below.
Afterward, continue reading instructions below.
a. Pull rope out slowly until you feel drag.
b. Without allowing the rope to retract, continue
pulling rope with one rapid full arm stroke.
a. Pull rope out slowly until you feel drag.
b. Without allowing the rope to retract, continue
pulling rope with one rapid full arm stroke.
c. Return rope slowly to original position.
c. Return rope slowly to original position.
NOTE
Following the instructions listed in the steps above avoids
potential damage to the recoil mechanism.
NOTE
Following the instructions listed in the steps above avoids
5. If engine fails to start after 3 attempts repeat steps 2
thru 4 and try again.
potential damage to the recoil mechanism.
6. If engine fails to start after 3 attempts repeat steps 2
thru 5 and try again.
6. When engine starts:
a. Move engine throttle control to “FAST” position.
7. If engine does NOT start after following steps 1 thru 6,
contact your Authorized TecumsehPower Servicing
Dealer. DO NOT attempt to start or troubleshoot this
engine in any other way.
b. Next, move engine throttle control to desired speed
in “RUN” range.
NOTES
If engine starts but falters when engine throttle control is
moved to “FAST” position:
II. Choke Only
1. To avoid carbon monoxide poisoning, be sure engine is
outdoors in a well-ventilated area.
a. Move engine throttle control back to “CHOKE”
Afterward, continue reading instructions below.
2. Move engine throttle control to “CHOKE” or “START”
position, if present (see equipment manufacturer’s
Afterward, continue reading instructions below.
b. Next, move engine throttle control to “FAST”
position.
If engine dies after engine throttle control is moved to
“FAST” position, repeat steps 2 thru 6 to restart engine.
NOTE
If restarting a warm engine after a short shutdown, move
engine throttle control to “FAST” position instead of
page 10. Afterward, continue reading instructions below.
7. If engine fires but does NOT continue to run, move
engine throttle control to “FAST” position and start
engine.
8. If engine fails to start after 3 attempts in the “FAST”
position, move engine throttle control to “CHOKE”
position and start engine.
3. Operate equipment control to release engine brake or
clutch, if present (see equipment manufacturer’s
continue reading instructions.
9. If engine does NOT start after following steps 1 thru 8,
contact your Authorized TecumsehPower Servicing
Dealer. DO NOT attempt to start or troubleshoot this
engine in any other way.
181-1215-14
Four-Cycle Engine • Vertical Crankshaft • Air-Cooled
Page 11
Download from Www.Somanuals.com. All Manuals Search And Download.
III. Primer Bulb and Choke
In Temperatures Above 40°F (5°C):
3
2
Follow instructions in Section B.I. "I. Primer Bulb Only"
1
In Temperatures Below 40°F (5°C):
1. To avoid carbon monoxide poisoning, be sure engine is
outdoors in a well-ventilated area.
2. Move engine throttle control to “CHOKE” or “START”
position, if present (see equipment manufacturer’s
3. When starting a cold engine, push primer bulb firmly 3
times, allowing primer bulb to return completely to orig-
inal position between pushes. See Figure 24 on page
11. Afterward, continue reading instructions below.
1. Starter Cord Handle
2. Engine Throttle Control
3. Equipment Control
NOTES
Be sure to cover vent hole when pressing primer bulb.
See Figure 24 on page 11. Afterward, continue reading
instructions below.
Figure 25. Typical Engine Controls
Cooler temperatures may require pushing primer bulb firmly
5 times.
DO NOT use primer bulb to restart a warm engine after a
short shutdown. Doing so will flood the engine and may
result in equipment malfunction.
STOP
STOP SLOW
RUN FAST CHOKE PRIMER
4. Operate equipment control to release engine brake or
clutch, if present (see equipment manufacturer’s
instructions). See Figure 25.
Figure 26. Typical Engine Symbols
When pulling starter rope, the rope
WARNING
can unexpectedly jerk back toward
engine causing serious injury. To avoid this risk, carefully
follow these instructions:
3
a. Pull rope out slowly until you feel drag.
2
b. Without allowing the rope to retract, continue pulling
rope with one rapid full arm stroke.
c. Return rope slowly to original position.
1
NOTE
Following the instructions listed in the steps above avoids
potential damage to the recoil mechanism.
1. “SLOW” Position
2. “RUN” Range
6. When engine starts:
3. “FAST” Position
a. Move engine throttle control to “FAST” position.
See Figures 25 thru 27.
Figure 27. Start/Choke Control Positions
b. Next, move engine throttle control to desired speed
in “RUN” range.
7. If engine fires but does NOT continue to run, move engine
throttle control to “FAST” position and start engine.
NOTES
If engine starts but falters when engine throttle control is
moved to “FAST” position:
8. If engine fails to start after 3 attempts in the “FAST”
position, move engine throttle control to “CHOKE”
position and start engine.
a. Move engine throttle control back to “CHOKE”
position.
9. If engine does NOT start after following steps 1 thru 8,
contact your Authorized Tecumseh Servicing Dealer.
DO NOT attempt to start or troubleshoot this engine in
any other way.
b. Next, move engine throttle control to “FAST”
position.
If engine dies after engine throttle control is moved to
“FAST” position, repeat steps 2 thru 6 to restart engine.
Page 12
Four-Cycle Engine • Vertical Crankshaft • Air-Cooled
181-1215-14
Download from Www.Somanuals.com. All Manuals Search And Download.
VI. Stopping Your Engine and
Short-Term Storage
Stop engine according to equipment manufacturer’s
instructions.
To avoid unsupervised operation of
WARNING
an engine, especially by children,
NEVER leave it unattended when it is running. Always turn
off the engine after use and remove ignition key, if
provided. Failure to do so may lead to serious injury or
death.
Figure 28. Disconnecting/Connecting Spark Plug
NEVER store engine with fuel in the
WARNING
fuel tank inside a building with
potential sources of ignition such as hot water or space
heaters, clothes dryers, electric motors, etc. Doing so may
lead to an explosion resulting in death or serious injury.
1
2
VII. Maintenance
To avoid serious injury or death, an
WARNING
adult should perform maintenance on
this engine. Only allow children to perform maintenance if
an adult has determined they are experienced and capable
of such operation.
1. Grounding Post Connection
2. Spark Plug Connection
To prevent accidental starting when
WARNING
working on equipment, always:
Figure 29. Typical Grounding Post/Spark Plug Connection
• Carefully disconnect spark plug wire and keep it
away from spark plug. See Figures 28 and 29.
A. Checking and Changing Oil
To avoid engine damage, it is important to:
• Keep the disconnected spark plug wire
securely away from metal parts where arcing
could occur.
• Check oil level before each use and every 5
operating hours when engine is warm. See
Afterward, continue reading instructions below.
• Carefully attach the spark plug wire to the
grounding post, if provided.
• Change oil after first 2 operating hours and every 25
operating hours thereafter; more often if operated in
extremely dusty or dirty conditions. Engine should
still be warm but NOT hot from recent use.
• Disconnect battery at negative terminal first, if
engine is equipped with a DC electric starter.
• Turn all engine switches to “OFF” position.
• Remove ignition key, if provided.
NOTES
For engines with a dipstick, see "I. Oil Fill Cap/Dipstick"
For engines without a dipstick, see "II. Oil Fill Cap/Plug"
181-1215-14
Four-Cycle Engine • Vertical Crankshaft • Air-Cooled
Page 13
Download from Www.Somanuals.com. All Manuals Search And Download.
I. Oil Fill Cap/Dipstick
If your engine has an oil fill cap/dipstick go to step 1. If your
engine does NOT have an oil fill cap/dipstick, see "II. Oil Fill
1. Carefully disconnect spark plug wire and keep it away
Accidental Starts" instructions on page 2. Afterward,
continue reading instructions below.
Figure 30. Disconnecting/Connecting Spark Plug
• Keep the disconnected spark plug wire
securely away from metal parts where arcing
could occur.
• Carefully attach the spark plug wire to the
grounding post, if provided.
1
2
2. Be sure fuel fill cap is on and tightened securely.
1. Grounding Post Connection
2. Spark Plug Connection
Figure 31. Typical Grounding Post/Spark Plug Connection
3. Carefully turn engine on the side with the carburetor
4. Place approved recyclable oil container under oil fill
cap/dipstick.
Figure 32. Fuel Fill Cap
5. Remove oil fill cap/dipstick.
6. Tip engine with the carburetor side up to position the oil
flow, so it will drain from the lowest point on the engine
(see equipment manufacturer’s instructions).
Carburetor Side Up
2
7. Drain oil into an approved recyclable oil container.
NOTE
Used oil must be disposed of at a proper collection center.
1
1. Oil Fill/Drain Tube (Cap/Dipstick)
2. Carburetor
Figure 33. Draining Oil Sump
Page 14
Four-Cycle Engine • Vertical Crankshaft • Air-Cooled
181-1215-14
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Clean area around oil fill tube and oil fill cap/dipstick.
9. Place engine back onto a level upright position with the
wheels touching the ground.
Figure 34. Oil Fill Cap/Dipstick
10. Fill with recommended oil. See Table 1 and "III. Oil and
Fuel Specifications" instructions on page 4. Afterward,
continue reading instructions below.
NOTES
DO NOT overfill oil filler. Doing so may result in oil carry-over
to the air cleaner and equipment and cause malfunction or
damage.
Figure 35. Disconnecting/Connecting Spark Plug
DO NOT allow oil level to fall below the “ADD” mark on
dipstick. Doing so may result in equipment malfunction or
damage.
1
2
Contact your Authorized TecumsehPower Servicing Dealer
for TecumsehPower Oil.
11. Wipe away any spilled oil.
1. Grounding Post Connection
2. Spark Plug Connection
12. Install oil fill cap/dipstick. Tighten securely.
Figure 36. Typical Grounding Post/Spark Plug Connection
13. Carefully disconnect spark plug wire from grounding
14. Connect spark plug wire to spark plug before attempt-
ing to start engine.
NOTES
The oil filter if so equipped, should be changed every 100
operating hours or at least once a year.
Figure 37. Typical Spark Plug Connection
The filter should be changed more often if the engine is
operated in extremely dusty or dirty conditions.
Contact your Authorized TecumsehPower Servicing Dealer
for a genuine replacement Oil Filter.
181-1215-14
Four-Cycle Engine • Vertical Crankshaft • Air-Cooled
Page 15
Download from Www.Somanuals.com. All Manuals Search And Download.
II. Oil Fill Cap/Plug
If your engine does NOT have an oil fill cap/dipstick go to
step 1. If your engine has an oil fill cap/dipstick, see
1. Carefully disconnect spark plug wire and keep it away
from spark plug. See Figures 38 and 39. See “G” Avoid
Accidental Starts” instructions on page 2. Afterward,
continue reading instructions below.
Figure 38. Disconnecting/Connecting Spark Plug
• Keep the disconnected spark plug wire
securely away from metal parts where arcing
could occur.
1
2
• Carefully attach the spark plug wire to the
grounding post, if provided.
2. Be sure fuel fill cap is on and tightened securely.
1. Grounding Post Connection
2. Spark Plug Connection
3. Be sure you find the correct oil drain plug location (see
equipment manufacturer’s instructions). See Figure 41.
Figure 39. Typical Grounding Post/Spark Plug Connection
4. Clean area around oil drain plug.
5. Place approved recyclable oil container under oil drain
plug, tipping engine to position the oil drain plug at the
lowest point on the engine (see equipment manufac-
turer’s instructions).
Figure 40. Fuel Fill Cap
6. Remove oil drain plug and drain oil into an approved
recyclable oil container.
NOTE
Used oil must be disposed of at a proper collection center.
7. Install oil drain plug and tighten securely.
Figure 41. Oil Drain Plug Locations
Page 16
Four-Cycle Engine • Vertical Crankshaft • Air-Cooled
181-1215-14
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Add oil to overflow point, making sure to avoid spilling
Figure 42. Afterward, continue reading instructions
below.
NOTES
DO NOT overfill oil filler. Doing so may result in oil
carry-over to the air cleaner and equipment and cause
malfunction or damage.
Contact your Authorized TecumsehPower Servicing Dealer
for TecumsehPower Oil.
Figure 42. Oil Fill Plug
9. Wipe away any spilled oil.
10. Screw oil fill cap/plug back into oil fill hole. Tighten
securely. See Figure 42.
11. Carefully disconnect spark plug wire from grounding
Figure 43. Disconnecting/Connecting Spark Plug
12. Connect spark plug wire to spark plug before attempt-
ing to start engine.
1
2
NOTES
The oil filter if so equipped, should be changed every 100
operating hours or at least once a year.
The filter should be changed more often if the engine is
operated in extremely dusty or dirty conditions.
1. Grounding Post Connection
2. Spark Plug Connection
Contact your Authorized TecumsehPower Servicing Dealer
for a genuine replacement Oil Filter.
Figure 44. Typical Grounding Post/Spark Plug Connection
Figure 45. Typical Spark Plug Connection
181-1215-14
Four-Cycle Engine • Vertical Crankshaft • Air-Cooled
Page 17
Download from Www.Somanuals.com. All Manuals Search And Download.
B. Removing Debris from Engine
2
Before each use, remove the air cleaner cover. Discard
grass clippings, dirt and debris from the following areas:
• Levers and Linkage
• Cooling Fins
• Air Intake Screen
• Air Inlet
• Guards
Removing debris will insure adequate cooling, correct
engine speed and reduce the risk of fire. See Figure 46.
3
1
C. Spark Plug
Check spark plug yearly or every 100 operating hours.
1. Clean area around spark plug.
2. Remove and inspect spark plug.
1. Cooling Fins
2. Air Intake Screen
3. Levers and Linkage
3. Replace spark plug if porcelain is cracked or if
electrodes are:
Figure 46. Debris Removal Locations
3
• Pitted
• Burned
2
• Fouled with Deposits
4. Check electrode gap with wire feeler gauge and set
gap to—.030 in. (0.76 mm) if necessary. See Figure 47.
5. Install spark plug and tighten securely.
NOTE
A resistor spark plug must be used for replacement. Contact
your Authorized TecumsehPower Servicing Dealer for a
genuine replacement Resistor Spark Plug.
1
1. .030 in. (0.76 mm) Gap
2. Electrodes
D. Cleaning/Replacing Air Cleaner
Your engine has an air cleaner which helps prevent
premature engine wear and failure. NEVER run engine
without complete air cleaner installed on engine. Your air
cleaner periodically needs to be cleaned or replaced.
Your engine will be equipped with one of the following air
cleaners; Type A, B, C, D or E. Follow instructions for the
air cleaner type that resembles your model. See Figures 48
instructions below.
3. Porcelain
Figure 47. Resistor Spark Plug
I. Servicing Foam Filters
Clean foam filters every 3 months or every 25 operating
hours. Clean daily if used in extremely dusty conditions.
After removing the filter, follow these cleaning instructions
below:
NOTES
1. Wash in warm water and detergent solution then press
(DO NOT twist) until all dirt is removed.
ALWAYS inspect filter(s) for discoloration or dirt
accumulation. If either is present, see "I. Servicing Foam
Filters" instructions on page 19. Afterward, continue reading
instructions below.
2. Rinse thoroughly until water is clear.
3. Wrap in a clean cloth and press (DO NOT twist) until
completely dry.
NOTE
Contact your Authorized TecumsehPower Servicing Dealer
for a genuine replacement Air Cleaner.
DO NOT oil foam filter.
4. Install foam filter.
NOTE
Proceed with installation instructions for the air cleaner type
that resembles your model.
Page 18
Four-Cycle Engine • Vertical Crankshaft • Air-Cooled
181-1215-14
Download from Www.Somanuals.com. All Manuals Search And Download.
II. Servicing Paper Filters
5
4
3
Paper filters cannot be cleaned and must be replaced once
a year or every 100 operating hours; more often if used in
extremely dusty conditions. Replacement filters are
available at an Authorized TecumsehPower Servicing
Dealer. Follow the instructions next to the drawing of your
air cleaner to remove and replace it.
2
NOTE
4
DO NOT put oil on or clean a paper filter.
6
III. Removal and Installation-Type “A” Air Cleaner
1. Press cover release button and lift cover upward. See
2. Inspect filter(s) for discoloration or dirt accumulation. If
either is present, see "I. Servicing Foam Filters"
instructions on page 18. Afterward, continue reading
instructions below.
7
1
8
1. Cover Release Button
2. Foam / Screen Filter (Optional)
3. Foam Filter
4. Tab
3. Clean inside of cover and body thoroughly.
4. Install filter(s) in body where applicable.
5. Cover
5. Push cover downward on body and press until cover
locks with body tab securely.
6. Slot
7. Body
8. Body Tab
Figure 48. Air Cleaner Type “A” Assembly
4
5
6
7
8
3
IV. Removal and Installation-Type “B” Air Cleaner
1. Remove cover by pulling tab “A” away from body while
2
2. Inspect filter(s) for discoloration or dirt accumulation. If
either is present, see "I. Servicing Foam Filters"
instructions on page 18 and /or "II. Servicing Paper
Filters" instructions listed above. Afterward, continue
reading instructions below.
1
3. Clean inside of cover and body thoroughly.
4. Install foam filter(s) and new paper filter(s) in body
where applicable.
1. Tab “B”
5. Install cover by hooking slot of cover over tab “B” on
body.
2. Foam Filter
3. Slot
6. Push cover down, snapping cover onto body securely.
4. Optional Paper Filter
5. Cover
6. Tab “A”
7. Foam Filter
8. Body
Figure 49. Air Cleaner Type “B” Assembly
181-1215-14
Four-Cycle Engine • Vertical Crankshaft • Air-Cooled
Page 19
Download from Www.Somanuals.com. All Manuals Search And Download.
V. Removal and Installation-Type “C” Air Cleaner
3
4
1. Turn cover counterclockwise to remove.
Paper Filters" instructions on page 19. Afterward, con-
tinue reading instructions below.
5
1
6
3. Discard paper filter.
4. Clean cover and flange thoroughly.
5. Install new paper filter into cover.
2
6. Position cover and filter against flange with tab on
cover inserted into lower left corner of slot in flange.
7. Push cover firmly against flange and turn
clockwise as far as it will go.
1
8. Be sure retainers are locked around flange.
1. Retainer
2. Slot
3. Flange
4. Paper Filter
5. Tab
6. Cover
Figure 50. Air Cleaner Type “C” Assembly
VI. Removal and Installation-Type “D” Air Cleaner
5
1. Remove cover by pulling tab “A” away from body while
4
3
2. Inspect filter(s) for discoloration or dirt accumulation.
If either is present, see "I. Servicing Foam Filters"
instructions on page 18 and/or "II. Servicing Paper
Filters" instructions on page 19. Afterward, continue
reading instructions below.
6
3. Discard paper filter.
2
4. Clean inside of cover and body thoroughly.
5. Install foam filter(s) and new paper filter.
7
6. Install cover by hooking slot of cover over tab “B” on
body.
1
7. Push cover down, snapping cover onto body securely.
1. Tab “B”
2. Foam Filter
3. Slot
4. Cover
5. Tab “A”
6. Paper Filter
7. Body
Figure 51. Air Cleaner Type “D” Assembly
Page 20
Four-Cycle Engine • Vertical Crankshaft • Air-Cooled
181-1215-14
Download from Www.Somanuals.com. All Manuals Search And Download.
VII.Removal and Installation-Type “E” Air Cleaner
2
4
Paper Filters" instructions on page 19. Afterward,
continue reading instructions below.
3. Discard paper filter.
4. Clean cover and flange thoroughly.
5. Insert new paper filter into cover.
6. Line up tabs on cover with slots on flange.
3
7. Push cover firmly against flange and turn counterclock-
wise until cover locks securely in place.
1
8. Secure cover and be sure it is in vertical position.
E. Carburetor
5
If you think your carburetor needs adjusting, see your
nearest Authorized TecumsehPower Servicing Dealer.
Engine performance should not be affected at altitudes
up to 7,000 feet (2,134 meters). For operation at higher
elevations, contact an Authorized TecumsehPower
Servicing Dealer.
1. Paper Filter
2. Slots
3. Flange
4. Tabs
F. Engine Speed
5. Cover
To avoid serious injury or death,
WARNING
DO NOT modify engine in any way.
Figure 52. Air Cleaner Type “E” Assembly
Tampering with the governor setting can lead to a runaway
engine and cause it to operate at unsafe speeds. NEVER
tamper with factory setting of engine governor.
VIII. Transporting Your Engine
Running the engine faster than the speed set at the factory
can be dangerous and will VOID THE ENGINE WARRANTY.
NEVER transport this engine inside
another vehicle or in any enclosed
WARNING
space if there is any gasoline in the tank. Fuel vapor or
spilled fuel may ignite leading to serious injury or death.
G. Engine Stopping Mechanism
Some engines are equipped with a
federally-mandated mechanism which
If there is fuel in the fuel tank, close
the fuel shut-off valve, if equipped,
WARNING
WARNING
stops the engine and mower blade. To avoid serious injury
or death as a result of contact with the mower blade, DO
NOT interfere with or bypass this mechanism. Parts of the
mechanism may be subject to wear and must be checked
once a year by an Authorized TecumsehPower Servicing
Dealer. In the event the mechanism fails for any reason,
you must NOT use the engine until corrected by an
Authorized TecumsehPower Servicing Dealer.
and transport the engine upright in an open vehicle, such
as an open trailer or open bed of a pickup truck.
If you DO NOT have an open vehicle and have to transport
the engine upright in a closed vehicle, follow these steps
for emptying the fuel tank before transporting:
1. Empty fuel tank by using a commercially available
suction device designed for use with gasoline.
To avoid serious injury or death, DO
NOT pour fuel from engine or siphon
H. Adjustments
WARNING
DO NOT make any engine adjustments. Factory settings
are satisfactory for most conditions. If adjustments are
needed, contact your Authorized TecumsehPower
Servicing Dealer.
fuel by mouth.
2. Drain fuel into an approved red GASOLINE container,
being careful to avoid spilling.
3. Run the engine until remaining fuel is consumed.
NEVER leave the engine unattended
WARNING
when it is running and NEVER run
engine in enclosed areas to avoid death or serious injury.
181-1215-14
Four-Cycle Engine • Vertical Crankshaft • Air-Cooled
Page 21
Download from Www.Somanuals.com. All Manuals Search And Download.
III. Fuel System
IX. Storing Your Engine
A. Short-Term/Seasonal Storage
I. Clean Engine
To avoid stale gas and carburetor problems, treat the fuel
system in the following method below:
NOTES
TecumsehPower Company recommends using
ULTRA-FRESH™ Gasoline Stabilizer as an acceptable
method of minimizing formation of fuel gum deposits during
storage. This product is available from your Authorized
TecumsehPower Servicing Dealer.
Before servicing the engine remove the air cleaner cover
and/or blower housing. Remove grass clippings, dirt and
debris from the following areas:
• Cooling Fins
• Air Intake Screen
• Levers
Always follow mix ratio found on stabilizer container. Failure
to do so may result in equipment damage.
It is NOT necessary to empty stabilized gas from fuel tank.
• Linkage
IV. Fuel Treatment
• Guards
1. Add fuel stabilizer according to manufacturer’s
instructions.
• Carburetor
• Head
2. Run engine at least 10 minutes after adding stabilizer
to allow it to reach carburetor.
Removing debris will insure adequate cooling, correct
engine speed and reduce the risk of fire.
NEVER store engine with fuel in the
WARNING
fuel tank inside a building with
II. Fuel Storage
potential sources of ignition such as hot water or space
heaters, clothes dryers, electric motors, etc. Doing so may
lead to an explosion resulting in death or serious injury.
NEVER store engine with fuel in the
fuel tank inside a building with
WARNING
potential sources of ignition such as hot water or space
heaters, clothes dryers, electric motors, etc. Doing so may
lead to an explosion resulting in death or serious injury.
NOTE
Instead of using a fuel preservative/stabilizer, you can
empty the fuel tank as described under "I. Draining Fuel"
NOTES
If engine fuel stored in the gas tank and/or an approved gas
container is to be unused without gasoline stabilizer for
more than 15-30 days, prepare it for short-term/seasonal
continue reading instructions below.
If engine fuel is to be stored for more than one season,
without gasoline stabilizer, it will gradually deteriorate. Also,
if it is stored in the engine’s gas tank without gasoline
stabilizer it is likely that your carburetor will have gum
deposits, a clogged fuel system and will void your warranty.
Prepare the fuel for extended storage. See "B. Extended
Storage" instructions on page 23. Afterward, continue
reading instructions.
Page 22
Four-Cycle Engine • Vertical Crankshaft • Air-Cooled
181-1215-14
Download from Www.Somanuals.com. All Manuals Search And Download.
B. Extended Storage
I. Draining Fuel
NOTES
Clean debris from engine before emptying fuel from fuel
Afterward, continue reading instructions below.
If you have prepared your fuel for short-term storage it is
NOT necessary to empty fuel that contains stabilizer from
your fuel tank. See "A. Short-Term/Seasonal Storage"
instructions on page 22. Afterward, continue reading
instructions below.
Figure 53. Disconnecting/Connecting Spark Plug
To avoid serious injury or death,
WARNING
DO NOT pour fuel from engine or
1
2
siphon fuel by mouth.
1. To prevent serious injury from fuel fires, empty fuel tank
by running engine until it stops from lack of fuel. DO
NOT attempt to pour fuel from engine.
2. Run the engine while waiting until the remaining fuel is
consumed.
NEVER leave the engine unattended
WARNING
when it is running and NEVER run
engine in enclosed areas to avoid death or serious injury.
1. Grounding Post Connection
2. Spark Plug Connection
Figure 54. Typical Grounding Post/Spark Plug Connection
NOTE
If you operate the engine during all four seasons, it is NOT
necessary to lubricate the cylinder bore.
5. Grasp starter cord handle:
a. Pull out slowly using a full arm stroke.
II. Oil Cylinder Bore
b. Repeat once. (This will distribute oil throughout the
cylinder to prevent corrosion during storage.)
When lubricating cylinder bore, fuel
CAUTION
may spray from spark plug hole. To
prevent serious injury from fuel fires, follow these
instructions:
c. Proceed to Step 7.
6. Push starter button or turn ignition switch key to
“START” position. Immediately release starter button or
turn ignition switch key to “OFF” position. (This will dis-
tribute oil throughout the cylinder to prevent corrosion
during storage.)
1. Carefully disconnect spark plug wire and keep it away
• Keep the disconnected spark plug wire
securely away from metal parts where arcing
could occur.
7. Remove rag covering spark plug hole.
8. Install spark plug.
• Carefully attach the spark plug wire to the
grounding post, if provided.
9. Carefully disconnect spark plug wire from grounding
post, if provided.
• Disconnect battery at negative terminal first, if
engine is equipped with a DC electric starter.
10. Connect spark plug wire to spark plug before
attempting to start engine.
• Turn all engine switches to “OFF” position.
• Remove ignition key, if provided.
2. Remove spark plug.
III. Oil
Change oil if NOT changed within the last 3 months. See
3. Squirt 1oz. (30 ml) of clean engine oil into spark plug
hole.
IV. Battery
4. Cover spark plug hole with rag to prevent fuel from
spraying from spark plug hole when engine is started.
See equipment manufacturer’s instructions for proper
battery storage, if machine is equipped with a battery.
NOTES
For engines equipped with recoil starters proceed to Step 5.
For engines equipped with electric starters proceed to Step 6.
181-1215-14
Four-Cycle Engine • Vertical Crankshaft • Air-Cooled
Page 23
Download from Www.Somanuals.com. All Manuals Search And Download.
X. Preventing Forest, Brush and
Grass Fires
Table 5. Maintenance Intervals
Procedure
Time
Local, state and federal laws may require use of a spark
arrester to prevent fires. For example, it is a violation of
California Public Resources Code (section 4442) to use or
operate engine on any forest-covered, brush-covered or
unimproved grass-covered land unless engine is equipped
with a spark arrester. Spark arrester must be maintained in
effective working order by owner and/or operator.
After First 2 Hours
When Engine is Warm
Change
Oil
Every 5 Hours
or
Before Each Use
Check
Oil
Level
Every 5 Hours
Or
Before Each Use
To determine if your engine has a spark arrester, locate the
muffler on your engine. For example, the muffler discharge
will have a spark arrester cover that reads “Screen Type
36085”.
Clean
Cooling
Fins
Every 25 Hours
or
Clean
Foam
Filter
If your engine does NOT have a spark arrester, you may
purchase one from your Authorized TecumsehPower
Servicing Dealer. In some cases the muffler may need to
be replaced to allow the spark arrester to be installed.
3 Months
Every 25 Hours
or
Change
Oil
XI. Maintenance Intervals
3 Months
Maintenance is one of the most important things that
you can do to extend the life of your TecumsehPower
engine. If you are unable to perform maintenance intervals
yourself, contact your nearest Authorized TecumsehPower
Servicing Dealer. Find them on our website at
Every 100 Hours
or
Replace
Paper and Oil
Filter
Seasonally
Every 100 Hours
or
Check
Spark
Plug
Company at 1-800-558-5402 for additional information.
Seasonally
ALWAYS promptly follow maintenance intervals listed in
this manual. See Table 5.
Every 200 Hours
or
Replace
Spark
Plug
Seasonally
Scheduled Maintenance
After First 2 Hours When Engine is Warm
1. Change Oil
Date_______________Owner/Dealer
Page 24
Four-Cycle Engine • Vertical Crankshaft • Air-Cooled
181-1215-14
Download from Www.Somanuals.com. All Manuals Search And Download.
Every 5 Hours or Before Each Use
Every 25 Hours or 3 Months
1. Clean Foam Filter
1. Check Oil Level
2. Clean Cooling Fins
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
181-1215-14
Four-Cycle Engine • Vertical Crankshaft • Air-Cooled
Page 25
Download from Www.Somanuals.com. All Manuals Search And Download.
Every 25 Hours or 3 Months
1. Change Oil
Every 100 Hours or Seasonally
1. Replace Paper Filter
2. Replace Oil Filter
3. Check Spark Plug
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Every 200 Hours or Seasonally
1. Replace Spark Plug
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Date_______________Owner/Dealer
Page 26
Four-Cycle Engine • Vertical Crankshaft • Air-Cooled
181-1215-14
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
181-1215-14
Four-Cycle Engine • Vertical Crankshaft • Air-Cooled
Page 27
Download from Www.Somanuals.com. All Manuals Search And Download.
CALIFORNIA & US EPA EMISSION CONTROL WARRANTY STATEMENT
The U. S. Environmental Protection Agency (“EPA”), the
California Air Resources Board (“CARB”) and Tecumseh-
Power Company are pleased to explain the Federal and
California Emission Control Systems Warranty on your
new small off-road engine. In California, new 1995 and
later small off-road engines must be designed, built and
equipped to meet the State’s stringent anti-smog stan-
dards. In other states, new 1997 and later model year
engines must be designed, built and equipped, at the
time of sale, to meet the U.S. EPA regulations for small
non-road engines. TecumsehPower Company will war-
rant the emission control system on your small off-road
engine for the periods of time listed below, provided there
has been no abuse, neglect, unapproved modification, or
improper maintenance of your small off-road engine.
(any TecumsehPower Registered Service Dealer,
TecumsehPower Authorized Service Distributor or
TecumsehPower Central Warehouse Distributor) as soon
as a problem exists. The warranty repairs should be
completed in a reasonable amount of time, not to exceed
30 days.
Warranty service can be arranged by contacting either an
Authorized TecumsehPower Servicing Dealer and/or
TecumsehPower Company, c/o Service Manager, 900
North Street, Grafton, WI 53024-1499. Telephone 1-262-
377-2700 [or in USA/Canada call 1-800-558-5402].
IMPORTANT NOTE
This warranty statement explains your rights and obliga-
tions under the Emission Control System Warranty (“ECS
Warranty”) which is provided to you by TecumsehPower
Company pursuant to California law. TecumsehPower
Company also provides to original purchasers of new
TecumsehPower engines the TecumsehPower Company
Limited Warranties for New TecumsehPower Engines
and Electronic Ignition Modules. The TecumsehPower
Company Limited Warranties for New TecumsehPower
Engines and Electronic Ignition Modules (“Tecumseh-
Power Company Warranty”) are located on the back
cover of the Operator’s Manual, enclosed with all new
TecumsehPower engines. The ECS Warranty applies
only to the emission control system of your new engine.
To the extent that there is any conflict in terms between
the ECS Warranty and the TecumsehPower Company
Warranty, the ECS Warranty shall apply except in any cir-
cumstances in which the TecumsehPower Company
Warranty may provide a longer warranty period. Both the
ECS Warranty and the TecumsehPower Company War-
ranty describe important rights and obligations with
respect to your new engine.
Your emission control system may include parts such as
the carburetor, air cleaner assembly, ignition system,
exhaust system, crankcase breather assembly and, the
evaporative control system. Also included may be the
compression release system and other emission-related
assemblies.
Where a warrantable condition exists, TecumsehPower
Company will repair your small off-road engine at no cost
to you for diagnosis, parts and labor.
MANUFACTURER’S EMISSION CONTROL
SYSTEM WARRANTY COVERAGE
Emission control systems on 1995 and later model year
California small off-road engines are warranted for two
years as hereinafter noted. In other states, 1997 and later
model year engines are also warranted for two years. If,
during such warranty period, any emission-related part
on your engine is defective in materials or workmanship,
the part will be repaired or replaced by TecumsehPower
Company.
Warranty service can only be performed by a TecumsehPower
Authorized Servicing Dealer. At the time of requesting
warranty service, evidence must be presented of the date
of sale to the original purchaser. The purchaser shall pay
any charges for making service calls and/or for transport-
ing the products to and from the place where the inspec-
tion and/or warranty work is performed. The purchaser
shall be responsible for any damage or loss incurred in
connection with the transportation of any engine or any
part(s) thereof submitted for inspection and/or warranty
work.
OWNER’S WARRANTY RESPONSIBILITIES
As the small off-road engine owner, you are responsible
for the performance of the required maintenance listed in
your Operator’s Manual, but TecumsehPower Company
will not deny warranty solely due to the lack of receipts or
for your failure to provide written evidence of the perfor-
mance of all scheduled maintenance.
As the small off-road engine owner, you should, however,
be aware that TecumsehPower Company may deny you
warranty coverage if your small off-road engine or a part
thereof has failed due to abuse, neglect, improper main-
tenance or unapproved modifications.
If you have any questions regarding your warranty rights
and responsibilities, you should contact TecumsehPower
Company at 1-262-377-2700 or in USA/Canada call
You are responsible for presenting your small off-road
engine to a TecumsehPower Authorized Service Outlet
1-800-558-5402.
Revised February 2008
IMPORTANT!
The Emission Regulations may be different for your country. The Emissions Control Warranty Statement is only
applicable to engines with an emissions compliance statement and decal that references “Emissions Regulations”.
Page 28
Four-Cycle Engine • Vertical Crankshaft • Air-Cooled
181-1215-14
Download from Www.Somanuals.com. All Manuals Search And Download.
EMISSION CONTROL SYSTEM WARRANTY
Emission Control System Warranty (“ECS Warranty”) for 1995
and later model year California small off-road engines (for other
states, 1997 and later model year engines):
5. The owner shall not be charged for diagnostic labor which
leads to the determination that a part covered by the ECS
Warranty is in fact defective, provided that such diagnostic
work is performed at a TecumsehPower Authorized
Service Outlet.
A. APPLICABILITY: This warranty shall apply to 1995 and later
model year California small off-road engines (for other states,
1997 and later model year engines). The ECS Warranty
Period shall begin on the date the new engine or equipment is
delivered to its original, end-use purchaser, and shall continue
for 24 consecutive months thereafter.
6. TecumsehPower Company shall be liable for damages to
other original engine components or approved
modifications proximately caused by a failure under
warranty of an emission-related part covered by the ECS
Warranty.
B. GENERAL EMISSIONS WARRANTY COVERAGE:
TecumsehPower Company warrants to the original, end-use
purchaser of the new engine or equipment and to each
subsequent purchaser that each of its small off-road engines
is:
7. Throughout the ECS Warranty Period, TecumsehPower
Company shall maintain a supply of warranted emission-
related parts sufficient to meet the expected demand for
such emission-related parts.
1. Designed, built and equipped so as to conform with all
applicable regulations adopted by the Air Resources
Board pursuant to its authority in Chapters 1 and 2, Part 5,
Division 26 of the Health and Safety Code, and
8. Any TecumsehPower Company authorized and approved
emission-related replacement part may be used in the
performance of any ECS Warranty maintenance or repair
and will be provided without charge to the owner. Such
use shall not reduce TecumsehPower Company ECS
Warranty obligations.
2. Free from defects in materials and workmanship which, at
any time during the ECS Warranty Period, will cause a
warranted emissions-related part to fail to be identical in all
material respects to the part as described in the engine
manufacturer’s application for certification.
9. Unapproved add-on or modified parts may not be used to
modify or repair a TecumsehPower engine. Such use
voids this ECS Warranty and shall be sufficient grounds
for disallowing an ECS Warranty claim. TecumsehPower
Company shall not be liable hereunder for failures of any
warranted parts of a TecumsehPower engine caused by
the use of such an unapproved add-on or modified part.
C. THE ECS WARRANTY ONLY PERTAINS TO EMISSION-
RELATED PARTS ON YOUR ENGINE AS FOLLOWS:
1. Any warranted, emissions-related parts which are not
scheduled for replacement as required maintenance in the
Operator’s Manual shall be warranted for the ECS
Warranty Period. If any such part fails during the ECS
Warranty Period, it shall be repaired or replaced by
TecumsehPower Company according to Subsection 4
below. Any such part repaired or replaced under the ECS
Warranty shall be warranted for any remainder of the ECS
Warranty Period.
EMISSION-RELATED PARTS INCLUDE THE FOLLOWING:
1. Carburetor Assembly including internal components:
a) Carburetor gaskets
b) Intake pipe
2. Air Cleaner Assembly including components:
a) Air filter element
2. Any warranted, emissions-related part which is scheduled
only for regular inspection as specified in the Operator’s
Manual shall be warranted for the ECS Warranty Period. A
statement in such written instructions to the effect of
“repair or replace as necessary”, shall not reduce the ECS
Warranty Period. Any such part repaired or replaced under
the ECS Warranty shall be warranted for the remainder of
the ECS Warranty Period.
3. Ignition System including components:
a) Spark plug
b) Ignition module
c) Flywheel assembly
4. Exhaust System including components:
a) Catalytic muffler (if so equipped)
b) Muffler gasket (if so equipped)
3. Any warranted, emissions-related part which is scheduled
for replacement as required maintenance in the Operator’s
Manual, shall be warranted for the period of time prior to
the first scheduled replacement point for that part. If the
part fails prior to the first scheduled replacement, the part
shall be repaired or replaced by TecumsehPower
Company according to Subsection 4 below. Any such
emissions-related part repaired or replaced under the ECS
Warranty, shall be warranted for the remainder of the ECS
Warranty Period prior to the first scheduled replacement
point for such emissions-related part.
c) Exhaust manifold (if so equipped)
5. Crankcase Breather Assembly including components
a) Breather connection tube
6. Evaporative Control System including components:
a) Fuel line(s)
b) Fuel filter
c) Canister (if so equipped)
d) Fuel tank (if so equipped)
e) Fuel fill cap (if so equipped)
4. Repair or replacement of any warranted, emissions-
related part under this ECS Warranty shall be performed
at no charge to the owner at a TecumsehPower
Authorized Service Outlet.
Revised February 2008
IMPORTANT!
The Emission Regulations may be different for your country. The Emissions Control Warranty Statement is only
applicable to engines with an emissions compliance statement and decal that references “Emissions Regulations”.
181-1215-14
Four-Cycle Engine • Vertical Crankshaft • Air-Cooled
Page 29
Download from Www.Somanuals.com. All Manuals Search And Download.
XII. Warranty Information
LIMITED WARRANTY FOR NEW TECUMSEHPOWER ENGINES
AND ELECTRONIC IGNITION MODULES
For the time period shown below from the date of purchase and subject to the exceptions and limitations described herein, TecumsehPower Company will, at its option as
the exclusive remedy, either repair or replace for the original purchaser, free of charge, any part of any new TecumsehPower engine which is found, upon examination by
any Authorized TecumsehPower Servicing Outlet or by TecumsehPower’s Service Division, to be DEFECTIVE IN MATERIAL AND/OR WORKMANSHIP. This Limited
Warranty DOES NOT COVER (i) any TecumsehPower engine or part(s) thereof used to power any vehicle in competitive racing and/or used on any commercial or rental
track, or (ii) defects or damage caused by alterations or modifications of new TecumsehPower engines or parts or by normal wear, accidents, improper maintenance,
improper use or abuse of the product, or failure to follow the instructions contained in an Instruction Manual for the operation of the new TecumsehPower engine or part.
The cost of normal maintenance or replacement of service items which are not defective shall be paid for by the original purchaser. At the time warranty service is
requested, evidence must be presented of the date of purchase by the original purchaser. Any charge for making service calls and/or for transporting any engine or part(s)
thereof to and from the place where the inspection and/or warranty work is performed is payable solely by the purchaser. The purchaser is responsible for any damage or
loss incurred in connection with the transportation of any engine or part(s) thereof submitted for inspection and/or warranty work. WARRANTY SERVICE CAN ONLY BE
PERFORMED BY A TECUMSEHPOWER AUTHORIZED SERVICE OUTLET. Warranty service can be arranged by contacting a TecumsehPower Authorized Service
Outlet (any TecumsehPower Registered Service Dealer, TecumsehPower Authorized Service Distributor, or TecumsehPower Central Warehouse Distributor) or by
contacting TecumsehPower Company c/o Service Manager, 900 North Street, Grafton, Wisconsin USA 53024-1499.
(4)
(5)
“CONSUMER USE”
“COMMERCIAL USE”
Warranty
Within
U.S.A. and Canada
90 Day
Outside
Within
U.S.A. and Canada
No Warranty
1 Year
Outside
(6)
Category
(A)
U.S.A. and Canada
U.S.A. and Canada
No Warranty
1 Year
(1)
90 Day
(1)
(B)
1 Year
1 Year
(1)
(C)
2 Years
1 Year
1 Year
1 Year
(2)
(D)
2 Years
2 Years
1 Year
1 Year
(E)
2 Years
2 Years
1 Year
1 Year
(3)
(3)
(H)
2 ‘n 10
2 ‘n 10
1 Year
1 Year
(3)
(3)
(3)
(K)
2 ‘n 10
2 ‘n 10
2 ‘n 10
1 Year
(7)
(7)
(M)
3 Years
3 Years
1 Year
1 Year
(1) 2 years for Member States of the European Union. Consumers may have additional legal rights not affected by the terms of this warranty pursuant to EU Directive
1999/44/EC and the national legislation of certain Member States of the European Union.
(2) 1 year for Australian/New Zealand for rotary mower engines.
(3) 2 years on engine and 10 years (the first 5 years covering parts and labor only; the second 5 years covering parts only) on electronic ignition.
(4) For purposes of this warranty policy, “consumer use” shall mean consumer’s personal, residential, household use by the original retail purchaser.
(5) For purposes of this warranty policy, “commercial use” shall mean all other uses, including use for commercial, income producing, or rental purposes.
(6) The engine warranty category of your engine can be determined by review of the engine model number on the “Important Engine Information” decal. One letter in the
engine model number will be surrounded by parenthesis (A), (B), (C), (D), (E), (H) (K) or (M) and that letter is your engine warranty category designation.
(7) Qualification for three (3) year consumer use warranty under engine warranty category (M) may be determined by notation of an (M) designation on the “Important
Engine Information” decal located on the engine housing or an addendum decal affixed adjacent thereto.
THIS EXPRESS WARRANTY IS SUPPLEMENTED BY THE TECUMSEHPOWER CALIFORNIA EMISSION CONTROL WARRANTY STATEMENT, if any.
THIS EXPRESS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS WARRANTIES. Neither TecumsehPower Company nor any of its affiliates makes any warranties,
representations, or promises, written or oral, as to the quality of the engine or any of its parts, other than as set forth herein. ANY IMPLIED WARRANTY OF
MARKETABILITY, MERCHANTABILITY, OR FITNESS FOR A PARTICULAR PURPOSE, TO THE EXTENT THAT EITHER MAY APPLY TO ANY TECUMSEHPOWER
ENGINE OR PART(S) THEREOF, SHALL BE LIMITED IN DURATION TO THE PERIODS OF THE EXPRESS WARRANTIES SHOWN IN THE WARRANTY PERIOD
CHART ABOVE AND TO THE EXTENT PERMITTED BY LAW ANY AND ALL IMPLIED WARRANTIES ARE EXCLUDED. IN NO EVENT WILL TECUMSEHPOWER
COMPANY BE LIABLE FOR ANY INDIRECT, INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES AND/OR EXPENSES, INCLUDING, BUT NOT LIMITED TO,
ANY LOSS OF TIME, INCONVENIENCE, LOSS OF UNIT USE OR ANY COST OR EXPENSE OF SUBSTITUTE UNITS DURING PERIODS OF MALFUNCTION OR
NON-USE. Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages, so the above
limitation(s) or exclusion(s) may not apply to you. This Limited Warranty gives you specific legal rights and you may also have other legal rights which vary from state-to-state.
TecumsehPower Company neither assumes nor authorizes any other person, natural or corporate, to assume for TecumsehPower Company any other obligations or
liabilities in connection with or with respect to any TecumsehPower product or parts. The seller or dealer of a TecumsehPower product or part has no authority, whatsoever,
to make any representations or promises on behalf of TecumsehPower Company or to modify the terms or limitations of TecumsehPower’s warranty in any way.
Revised February 2008
!
WARNING
CALIFORNIA PROPOSITION 65
The engine exhaust from this product contains chemicals known
to the State of California to cause cancer, birth defects or other
reproductive harm.
TecumsehPower Company • Grafton, Wisconsin 53024-1499 • USA
Telephone: 1-800-558-5402
181-1215-14
(English) 6/01/08
Download from Www.Somanuals.com. All Manuals Search And Download.
|