Tecumseh Automobile Parts LH318XA User Manual

Operator’s Manual

LH318XA

LH358EA/LH358XA

Four-Cycle Engine • L-Head • Horizontal Crankshaft • Air-Cooled

Table of Contents

Important Notice! Safety Definitions ................................................ ii

I. General Safety Precautions ........................................................... 1

II. How to Get Service ........................................................................ 3

III. Oil and Fuel Specifications ............................................................. 3

IV. Before Starting Your Engine ........................................................... 4

V. Starting Your Engine ...................................................................... 8

VI. Stopping Your Engine and Short-Term Storage ........................... 12

VII. Maintenance ................................................................................ 12

VIII. Transporting Your Engine ............................................................. 15

IX. Storing your Engine ...................................................................... 15

X. Preventing Forest, Brush and Grass Fires ................................... 17

XI. Maintenance Intervals................................................................... 18

California & US EPA Emission Control Warranty Statement ........ 20

Emission Control System Warranty ............................................. 21

XII. Warranty Information ..................................................................... 22

Visit our web site at www.TecumsehPower.com

Maintenance Tips

Parts Look-Up System

Great Tecumseh Apparel

Nearest Authorized Tecumseh Servicing Dealer Location

181-630-14

(English) 12/01/06

Download from Www.Somanuals.com. All Manuals Search And Download.

• NEVER fill fuel tank indoors. Fill fuel tank outdoors

in a well-ventilated area.

I. General Safety Precautions

• DO NOT smoke while refueling tank.

! WARNING

• Use only an approved red GASOLINE container to

store and dispense fuel. Tecumseh recommends

purchasing gasoline in containers with a capacity of

2.5 gallons or less. Small containers are easier to

handle and help eliminate spillage during refueling.

Read equipment manufacturer’s manual and this

material thoroughly before using this engine. Failure to

do so can result in serious injury or death. Call Tecumseh

Power Company at 1-800-558-5402 or visit

www.TecumsehPower.com if you have any questions.

• DO NOT pour fuel from engine or siphon fuel by

mouth. To empty fuel tank see "I. Draining Fuel"

instructions on page 16.

A. Avoid Carbon Monoxide Poisoning

All engine exhaust contains

carbon monoxide, a deadly

gas. Breathing carbon

C. Adult Supervision of Operation, Refueling

and Maintenance

monoxide can cause

headaches, dizziness,

The manufacturer of the application may provide

information about who is allowed to use this engine (see

equipment manufacturer’s manual). Not everyone who is

allowed to use this engine is capable of safely and

responsibly operating, maintaining and/or fueling it.

Tecumseh recommends the following:

drowsiness, nausea, confusion

and eventually death.

Carbon monoxide is a colorless, odorless, tasteless gas

which may be present even if you do not see or smell any

engine exhaust. Deadly levels of carbon monoxide can

collect rapidly and you can quickly be overcome and

unable to save yourself. Also, deadly levels of carbon

monoxide can linger for hours or days in enclosed or

poorly-ventilated areas. If you experience any symptoms of

carbon monoxide poisoning, leave the area immediately,

get fresh air, and SEEK MEDICAL TREATMENT.

• An adult should fuel this engine. NEVER allow

children to refuel this engine. See "G. Filling Fuel

Tank" instructions on page 6.

• An adult should perform maintenance on this

engine. See "VII. Maintenance" instructions on

page 12. Only allow children to perform

maintenance if an adult has determined they are

experienced and capable of such operation.

To prevent serious injury or death from carbon monoxide:

• NEVER run engine indoors. Even if you try to

ventilate engine exhaust with fans or open windows

and doors, carbon monoxide can rapidly reach

dangerous levels.

• An adult should start the engine. See "G. Avoid

Accidental Starts" instructions on page 2. Only allow

children to start the engine if an adult has

determined they are experienced and capable of

such operation.

• NEVER run engine in poorly-ventilated or partially

enclosed areas such as barns, garages,

basements, carports, under dwellings, or in pits.

To avoid unsupervised operation of the engine, especially

by children, NEVER leave it unattended when it is running.

• NEVER run engine outdoors where engine exhaust

can be drawn into a building through openings such

as windows and doors.

D. Stay Away from Rotating Parts

NEVER operate the engine with an unguarded engine

shaft. See Figure 1.

B. Avoid Gasoline Fires

The equipment manufacturer may attach

a sprocket and chain or pulley and belt to

the engine shaft. If these parts are not

properly guarded, or if you are not sure

whether they are properly guarded, DO

NOT use your engine; contact the

equipment manufacturer. Hands, feet,

hair, jewelry, clothing, etc. can become

entangled in rotating parts, leading to

serious injury or death. To avoid serious

injury or death, be sure the flywheel

guard is in place. See Figure 1. See

Figure 2.

Gasoline (fuel) vapors are highly flammable

and can explode. Fuel vapors can spread

and be ignited by a spark or flame many feet

away from engine. To prevent injury or death

from fuel fires, follow these instructions:

• NEVER store engine with fuel in fuel

tank inside a building with potential

sources of ignition such as hot water and space

heaters, clothes dryers, electric motors, etc.

• NEVER remove fuel cap or add fuel when engine is

running.

• NEVER start or operate the engine with fuel fill cap

removed.

• Allow engine to cool before refueling.

181-630-14

Four-Cycle Engine • L-Head • Horizontal Crankshaft • Air-Cooled

Download from Www.Somanuals.com. All Manuals Search And Download.

Page 1

E. Do Not Modify Engine

To avoid serious injury or death, DO NOT modify engine in

any way. Tampering with the governor setting can lead to a

runaway engine and cause it to operate at unsafe speeds.

NEVER tamper with factory setting of engine governor.

! WARNING

Use of this engine on fun-carts, go-karts or mini-bikes

could result in serious injury or death. Tecumseh

manufactures the Power Sport line of engines for use in

such applications. Consult your local Authorized

Tecumseh Servicing Dealer, call 1-800-558-5402, or go

to www.TecumsehPower.com for additional information.

Figure 1. DO NOT Use Without Engine Shaft Guard

F. Avoid Burns and Fire from Hot Surfaces

The muffler and other engine parts become extremely hot

during operation and remain hot after the engine has

stopped.

• To avoid severe burns on contact,

NEVER operate the engine

without the muffler guard in place,

see Figure 2 and avoid hot areas

of the engine.

• To reduce the risk of fire keep all

materials that can burn, including

1. Muffler Guard

grass and leaves, away from muffler and rest of

engine. DO NOT operate, idle or park the engine

application in long dry grass or other dry ground

cover.

2. Flywheel Guard

Figure 2. Typical Engine Guard Locations

G. Avoid Accidental Starts

To prevent accidental starting when working on equipment

always:

• Disconnect spark plug wire and keep it away from

spark plug. See Figure 3.

• Keep the disconnected spark plug wire

securely away from metal parts where arcing

could occur.

• Attach the spark plug wire to the grounding

post, if provided. See Figure 4.

• Disconnect battery at negative terminal first, if

engine is equipped with an electric starter.

Figure 3. Disconnecting/Connecting Spark Plug

• Turn off all engine switches.

• Remove ignition key, if provided.

H. Use Hearing Protection

Engine noise may cause hearing damage. Always wear

hearing protection when operating an engine.

Figure 4. Typical Spark Plug Connection

Page 2

Four-Cycle Engine • L-Head • Horizontal Crankshaft • Air-Cooled

Download from Www.Somanuals.com. All Manuals Search And Download.

181-630-14

II. How to Get Service

2083

For engine adjustments, repairs or warranty service not

covered in this manual, contact your nearest Authorized

Tecumseh Servicing Dealer. Find them on our website at

www.TecumsehPower.com or call Tecumseh Power

Company at 1-800-558-5402.

TECUMSEH POWER COMPANY

THIS ENGINE MEETS 1995-2005 CALIF & US EPA

PHI APPLICABLE EMISSION REGULATIONS FOR SI

SORE ENGINES

LV195EA

361540D

Visit our web site at www.TecumsehPower.com

04015AA0001

195

4TPXS.1951BB

Maintenance Tips

Parts Look-Up System

Great Tecumseh Apparel

Nearest Authorized Tecumseh Servicing Dealer Location

ENGINE

MODEL:

A. Engine Identification Decal

SPEC:

A sample engine identification decal (See Figure 5.)

indicates the engine’s model number, specification of

engine and the date of manufacture (D.O.M.). Please look

at the decal on your engine and fill in this information in the

spaces provided for future reference.

D.O.M.:

Figure 5. Engine Identification Label

The engine identification decal also includes engine life

specifications for the emissions-related useful life period of

your engine. This period relates to the emission compliance

life as certified by EPA and/or CARB. To find the life period

specification for your engine, please look on your engine’s

decal and find the letter enclosed by quotation marks

between the words MODERATE and LIFE PERIOD. Match

one of the following letters with the letter printed on your

decal. For example, LH models are designated as “C” 250

hours, “B” 500 hours, and “A” 1000 hours.

TECHNICIAN'S HANDBOOK

3 TO 11 HP

4 -CYCLE

L-HEAD

ENGINES

B. Tecumseh Technician’s Handbooks

If you have a general understanding of internal combustion

engines and wish to repair and service your engine and/or

engine emission control systems yourself, a Technician’s

Handbook is available from your Authorized Tecumseh

Servicing Dealer. See Figure 6. This handbook covers

repairs and adjustments not covered within this Operator’s

Manual, and it is intended for individuals who have had

adequate training, experience and who practice proper tool

usage. Service procedures should be clearly understood

and practiced when servicing Tecumseh Engines. Order as

part no. 692509 for LH Models.

Figure 6. Technician’s Handbook

Table 1. Recommended Oil Usage

Tecumseh Recommended Oil Usage

Straight Grade

Tecumseh Part No.

730225A or SAE 30

Tecumseh manufactures and is responsible only for the

engine used on this power equipment. If repair or service is

needed for anything other than the engine, contact the

service source recommended by the equipment

manufacturer.

Multi Grade

Tecumseh Part No.

730226A or SAE 5W30 or SAE 10

Synthetic

Tecumseh Part No.

730263 or SAE 0W30

III. Oil and Fuel Specifications

20^OF

32^OF

0^OC

80^OF

100 F

-20 F

0^OF

40^OF

60^OF

A. Oil

10^OC

20^OC

30^OC

40^OC

-30 C

-20 C

-10 C

To operate engine you need to use a clean, high quality,

detergent oil. For recommended engine oil, See Table 1.

NOTES

Be sure original container is marked A.P.I. Service “SL/SJ”.

Using multigrade oil above 32°F (0°C) will increase oil

consumption. SAE10W40 is not recommended.

Tecumseh special-formulated oils are available at your

Authorized Tecumseh Servicing Dealer.

The oil sump capacity is 26 ounces or 1-5/8 U.S. Pints (.76

liters).

181-630-14

Four-Cycle Engine • L-Head • Horizontal Crankshaft • Air-Cooled

Download from Www.Somanuals.com. All Manuals Search And Download.

Page 3

Table 2. Recommended Fuel

B. Fuel

Use unleaded regular, unleaded premium or reformulated

automotive fuel only. You may use gasoline containing the

following components identified in Table 2.

Fuel Component

Percentage

Ethanol

10%

15%

Grain Alcohol (“Gasohol”)

• DO NOT use leaded fuel.

MTBE (Methyl Tertiary Butyl Ether)

ETBE (Ethyl Tertiary Butyl Ether)

• Fuel must be fresh and clean. NEVER use fuel left

over from last season or stored for long periods.

• NEVER mix oil with fuel.

• DO NOT use fuel containing Methanol (Wood

Alcohol).

Fill between “FULL”

and “ADD” Marks

The use of alternative fuels such as E85

CAUTION

or E20 are not recommended for use in

FULL

Tecumseh engines. Alternative fuels with high alcohol

content can cause hard starting, poor engine performance,

and may cause internal engine damage.

NOTE

ADD

Damage and/or performance problems that will occur from

use of fuels, other than those listed in the Operator’s

Manuals will not be considered warranty.

Figure 7. Engine Oil Level

IV. Before Starting Your Engine

A. Checking Oil Level

To avoid engine damage, it is important to:

• Check oil level before each use and every 5

operating hours when engine is warm. Check oil

level more frequently during engine break-in.

• Keep oil level between “FULL” and “ADD” marks on

dipstick. See Figure 7.

• Be sure oil fill cap is tightened securely.

NOTES

Do not overfill oil filler. Doing so may result in oil carry-over

to the air cleaner and equipment malfunction or damage.

Do not allow oil level to fall below the “ADD” mark on

dipstick. Doing so may result in equipment malfunction or

damage.

Contact your Authorized Tecumseh Servicing Dealer for

Tecumseh Oil.

Page 4

Four-Cycle Engine • L-Head • Horizontal Crankshaft • Air-Cooled

Download from Www.Somanuals.com. All Manuals Search And Download.

181-630-14

B. Filling Oil Sump

1. Be sure engine is upright and level.

2. Unscrew oil fill cap from oil filler tube and wipe dipstick

clean. See Figure 8.

3. Screw oil fill cap back into oil filler tube. Tighten

securely.

4. Unscrew and remove oil fill cap from oil filler tube. Note

oil level. If oil reading on dipstick is below “ADD” mark,

slowly add oil to reach “FULL” level. See Figure 7.

5. Screw oil fill cap back into oil filler tube. Tighten

securely.

6. Wipe away any spilled oil.

C. Engine Stop Switch

Some engines are equipped with an optional Stop Switch.

This rocker switch is used to shut off the ignition that

supplies the spark plug with power. Pressing the "OFF"

position will turn the engine off when it is running. This

switch must be in the “ON” position or the engine will not

start. See Figure 9.

1. Spark Plug Wire

D. Low Oil Shutdown Switch

2. Spark Plug Cap

Some engines are equipped with an optional Low Oil

Shutdown Switch. This is a lighted rocker switch that is

connected to a float switch in the engine crankcase. When

oil level drops below a predetermined level, the float switch

cuts off current to the spark plug and the engine stops

running. Oil must be added to the engine to bring the oil to

the proper level before the engine will start. If an attempt is

made to start the engine before oil is added, the switch will

flash as the engine rotates, and the engine will not start.

See Figure 10.

3. Oil Fill Cap with Long Dipstick

4. Spark Plug

5. Oil Fill Cap with Short Dipstick

6. Oil Drain Plug

Figure 8. Engine Components

Pressing the “OFF” position of the Shutdown Switch while

the engine is running, will turn the engine off. The engine

will not start with the switch in the “OFF” position.

1. ON Position

2. OFF Position

Figure 9. Engine Stop Switch

1. ON Position

2. OFF Position

3. Lighted Switch

Figure 10. Low Oil Shutdown Switch

Four-Cycle Engine • L-Head • Horizontal Crankshaft • Air-Cooled

181-630-14

Page 5

Download from Www.Somanuals.com. All Manuals Search And Download.

E. Low Oil Shutdown Light

Some engines are equipped with an optional low oil

shutdown system that includes a light but does not include

a rocker switch. The float switch in this system will shut the

engine off while it is running if the oil level in the crankcase

falls below a predetermined level. Oil must be added to the

engine to bring the oil to the proper level before the engine

will start. If an attempt is made to start the engine before oil

is added, the light will flash as the engine rotates, and the

engine will not start. See Figure 11.

F. Low Oil Shutdown System

Some engines are equipped with an optional low oil

shutdown system that does not have a rocker switch or a

light. The float switch in this system will shut the engine off

while it is running if the oil level in the crankcase falls below

a predetermined level. Oil must be added to the engine to

bring the oil to the proper level before the engine will start.

G. Filling Fuel Tank

An adult should fuel this engine.

WARNING

NEVER allow children to refuel this

engine. Gasoline (fuel) vapors are highly flammable and

can explode. Fuel vapors can spread and be ignited by a

spark or flame many feet away from engine. To prevent

injury or death from fuel fires, follow these instructions:

1. Air Cleaner

2. Carburetor

3. Muffler

1. Stop engine and allow it to cool before refueling.

2. Be sure engine is outdoors and in a well-ventilated

area.

4. Muffler Guard

5. Oil Fill Cap

6. Spark Plug

7. Fuel Fill Cap

3. Clean area around fuel fill cap and remove fuel fill cap.

See Figure 11.

4. Using an approved red GASOLINE container, add fuel

slowly, being careful to avoid spilling. DO NOT overfill

fuel tank. Leave space in the tank to allow fuel to

expand without overflowing.

8. Low Oil Shutdown Light (Optional)

9. Starter Cord Handle

Figure 11. Engine Components

5. Replace anti-splash fuel fill cap securely and wipe up

spilled fuel before starting engine. If fuel is spilled DO

NOT start engine. Move machine away from area of

spillage. Avoid creating any source of ignition until fuel

vapors are gone.

NOTES

Remove and discard white plastic fuel tank insert, if

provided. See Figure 12.

Replace a damaged or missing gas cap only with a genuine

Tecumseh replacement anti-splash fuel fill cap. Failure to do

so may VOID YOUR WARRANTY. See Figure 13.

6. Be sure fuel valve (optional) is open. See Figure 14.

Figure 12. Fuel Cap Insert Symbol

Page 6

Four-Cycle Engine • L-Head • Horizontal Crankshaft • Air-Cooled

Download from Www.Somanuals.com. All Manuals Search And Download.

181-630-14

H. Climate Guard Air® Cleaner

Some engines are equipped with an optional Climate

Guard Air Cleaner or Climate Guard. See Figures 15 and

16.

Front View

I. Moving The Inlet Air Scoop

For smooth and efficient engine operation, the inlet air

scoop must be aimed toward the engine and away from the

muffler for proper ambient air temperature to reach the

engine.

Bottom View

1. Remove the wing nut from the top of the air cleaner.

2. Lift the cover of the air cleaner.

Figure 13. Possible Anti-Splash Fuel Fill Cap(s)

Fuel Tank

3. Rotate the scoop to the desired position.

4. Replace the cover.

5. Install and tighten the wing nut.

NOTES

If the engine is not equipped with a CLIMATE GUARD air

cleaner, a CLIMATE GUARD Conversion Kit is available at

any Authorized Tecumseh Servicing Dealer. See Figure 15.

Turn Valve Clockwise

To “Off” Position

If the engine is equipped with a CLIMATE GUARD, no

changes need to be made when changing from summer to

winter operation. See Figure 16.

Fuel Valve “Open” Position Shown

Figure 14. Fuel Valve Positions

I. Winter Application

In temperatures below 32°F ( 0°C), the inlet air scoop

should be pointed directly at the muffler.

II. Summer Application

In temperatures above 32°F ( 0°C), the inlet air scoop

should be pointed toward the blower housing

(approximately 45° clockwise from ”WINTER” position).

Summer Position

Winter Position

Figure 15. Climate Guard Air Cleaner

Figure 16. Climate Guard

Four-Cycle Engine • L-Head • Horizontal Crankshaft • Air-Cooled

181-630-14

Page 7

Download from Www.Somanuals.com. All Manuals Search And Download.

V. Starting Your Engine

An adult should start the engine.

Only allow children to start engine if

WARNING

an adult has determined they are experienced and capable

of such operation.

If you are unable to start this engine

WARNING

after following instructions in this

manual, contact your Authorized Tecumseh Servicing

Dealer. To avoid serious burn injuries or damage to your

engine, DO NOT attempt to start or troubleshoot this

engine in any other way. For example:

1. ON Position

2. OFF Position

• DO NOT use starting fluid.

Figure 17. Engine Stop Switch

• DO NOT spray flammable vapors into carburetor or

onto air cleaner.

• DO NOT put flammable liquids into carburetor or

onto air cleaner.

• DO NOT operate engine or pull on starter rope with

spark plug removed. Fuel can spray from spark plug

hole and ignite.

This section contains starting instructions for several

different types of engines. In order to locate the instructions

that apply to your engine, first determine what type of

starter you have. If you have an electric starter see “A.

Engines with Electric Starters” instructions below. If you

have a manual recoil starter see "B. Engines with Recoil

Starters" instructions on page 10.

1. ON Position

2. OFF Position

3. Lighted Switch

Figure 18. Low Oil Shutdown Switch

A. Engines with Electric Starters

1. To avoid carbon monoxide poisoning, make sure

engine is outdoors in a well-ventilated area.

STOP

2. Move engine Stop Switch or Low Oil Shutdown Switch

to “ON”, if present (see equipment manufacturer’s

instructions). See Figures 17 and 18.

STOP SLOW

RUN FAST CHOKE PRIMER

3. Be sure fuel valve (optional) is open and all switches

are on. See Figure 14.

Figure 19. Typical Engine Symbols

4. Move Engine Speed Control to “FAST” position and set

Choke Control to ”FULL” position (see equipment man-

ufacturer’s instructions). See Figures 19 thru 22.

NOTE

If restarting a warm engine after a short shutdown, move

Engine Speed Control to “FAST” position and Choke

Control to “NO CHOKE” position.

5. Push starter button or turn ignition switch key (see

equipment manufacturer’s instructions) to start engine.

NOTES

DO NOT operate an electric starter for more than 5 seconds

each attempt.

If engine fails to start after 3 attempts repeat steps 2 thru 5.

Page 8

Four-Cycle Engine • L-Head • Horizontal Crankshaft • Air-Cooled

Download from Www.Somanuals.com. All Manuals Search And Download.

181-630-14

6. When engine starts:

a. Release starter button or ignition switch key.

b. Move Choke Control to “1/2 CHOKE” position until

engine runs smoothly. See Figures 20 thru 22.

c. Next, move Choke Control to “NO CHOKE” position.

Move Engine Speed Control to desired speed in

“RUN” range.

NOTES

If engine starts but falters when Choke Control is moved to

“NO CHOKE” position:

a. Momentarily move Choke Control back to “FULL

CHOKE” position. See Figures 20 thru 22.

b. Next, move Choke Control to “1/2 CHOKE” position

until engine runs smoothly.

Figure 20. Engine Mounted Speed Controls

c. Finally, move Choke Control to “NO CHOKE”

position.

7. If engine dies after Choke Control is to moved to “NO

CHOKE” position repeat steps 2 thru 6 to restart

engine.

8. If engine fires but does not continue to run, move

Choke Control to “NO CHOKE” position and start

engine.

9. If engine fails to start after 3 attempts in the “NO

CHOKE” position, move Choke Control to “FULL

CHOKE” position and start engine.

10. If engine does not start after following steps 1 thru 9,

contact your Authorized Tecumseh Servicing Dealer.

DO NOT attempt to start or troubleshoot this engine in

any other way.

1. Full Choke Position

2. 1/2 Choke Position

3. No Choke Position

Figure 21. Horizontal Mounted Choke Control

1. Full Choke Position

2. 1/2 Choke Position

3. No Choke Position

Figure 22. Vertical Mounted Choke Control

181-630-14

Four-Cycle Engine • L-Head • Horizontal Crankshaft • Air-Cooled

Download from Www.Somanuals.com. All Manuals Search And Download.

Page 9

B. Engines with Recoil Starters

1. To avoid carbon monoxide poisoning, make sure

engine is outdoors in a well-ventilated area.

2. Move engine Stop Switch or Low Oil Shutdown Switch

to “ON”, if present (see equipment manufacturer’s

instructions). See Figures 23 and 24.

3. Be sure fuel valve (optional) is open and all switches

are on. See Figure 14, on page 7.

4. Move Engine Speed Control to “FAST” position and set

Choke Control to ”FULL” position (see equipment man-

ufacturer’s instructions). See Figures 25 thru 28.

1. ON Position

2. OFF Position

NOTE

Figure 23. Engine Stop Switch

If restarting a warm engine after a short shutdown, move

Engine Speed Control to “FAST” position and Choke

Control to “NO CHOKE” position.

1. ON Position

2. OFF Position

3. Lighted Switch

Figure 24. Low Oil Shutdown Switch

STOP

STOP SLOW

RUN FAST CHOKE PRIMER

Figure 25. Typical Engine Symbols

Figure 26. Engine Mounted Speed Controls

Page 10

Four-Cycle Engine • L-Head • Horizontal Crankshaft • Air-Cooled

Download from Www.Somanuals.com. All Manuals Search And Download.

181-630-14

When pulling starter rope, the rope

can unexpectedly jerk back toward

WARNING

engine causing serious injury. To avoid this risk, carefully

follow these instructions:

5. Grasp starter cord handle. See Figure 29.

a. Pull rope out slowly until you feel drag.

b. Next, pull rope with one rapid full arm stroke.

c. Return rope slowly to original position.

NOTE

Following the instructions listed in the steps above avoids

potential damage to the recoil mechanism.

6. When engine starts:

a. Momentarily move Choke Control to “1/2 CHOKE”

position until engine runs smoothly. See Figures 27

and 28.

1. Full Choke Position

2. 1/2 Choke Position

3. No Choke Position

b. Next, move Choke Control to “NO CHOKE” position.

7. Move Engine Speed Control to desired speed in “RUN”

range. See Figure 26.

Figure 27. Horizontal Mounted Choke Control

NOTES

If engine starts but falters when Choke Control is moved to

“NO CHOKE” position:

a. Momentarily move Choke Control back to “FULL

CHOKE” position.

b. Next, move Choke Control to “1/2 CHOKE” position

until engine runs smoothly.

c. Finally, move Choke Control to “NO CHOKE”

position.

8. If engine dies after Choke Control is to moved to “NO

CHOKE” position repeat steps 2 thru 7 to restart

engine.

1. Full Choke Position

2. 1/2 Choke Position

3. No Choke Position

9. If engine fires but does not continue to run, move

Choke Control to “NO CHOKE” position and start

engine.

10. If engine fails to start after 3 attempts in the “NO

CHOKE” position, move Choke Control to “FULL

CHOKE” position and start engine.

Figure 28. Vertical Mounted Choke Control

11. If engine does not start after following steps 1 thru 10,

contact your Authorized Tecumseh Servicing Dealer.

DO NOT attempt to start or troubleshoot this engine in

any other way.

Figure 29. Starter Cord Handle

181-630-14

Four-Cycle Engine • L-Head • Horizontal Crankshaft • Air-Cooled

Download from Www.Somanuals.com. All Manuals Search And Download.

Page 11

VI. Stopping Your Engine and

Short-Term Storage

Stop engine according to equipment manufacturer’s

instructions.

To avoid unsupervised operation of

WARNING

an engine, especially by children,

NEVER leave it unattended when it is running. Always turn

off the engine after use and remove ignition key, if

provided.

NEVER store the engine with fuel in

WARNING

the fuel tank inside a building with

potential sources of ignition such as hot water and space

heaters, clothes dryers, electric motors, etc.

NOTE

See "A. Short Term/Seasonal Storage" instructions on page

15, for more information.

VII. Maintenance

An adult should perform

WARNING

maintenance on this engine.

Only allow children to perform maintenance if an adult has

determined they are experienced and capable of such

operation.

1. Spark Plug Wire

2. Spark Plug Cap

To prevent accidental starting when

working on equipment always:

WARNING

3. Oil Fill Cap with Long Dipstick

4. Spark Plug

• Disconnect spark plug wire and keep it away from

spark plug. See "G. Avoid Accidental Starts"

instructions on page 2. See Figure 30.

5. Oil Fill Cap with Short Dipstick

6. Oil Drain Plug

• Keep the disconnected spark plug wire

securely away from metal parts where arcing

could occur.

Figure 30. Engine Components

• Attach the spark plug wire to the grounding

post, if provided.

3. Be sure the gas cap is on and is tightened securely.

4. Clean area around oil drain plug. See Figure 30.

• Disconnect battery at negative terminal first, if

engine is equipped with an electric starter.

5. Place approved recyclable oil container under oil drain

plug, tipping engine to position the oil drain plug at the

lowest point on the engine. (See equipment manufac-

turer’s instructions).

• Turn off all engine switches.

• Remove ignition key, if provided.

6. Remove oil drain plug and drain oil.

See Figure 30.

A. Checking and Changing Oil

To avoid engine damage, it is important to:

• Check oil level before each use and every 5

operating hours. See "A. Checking Oil Level"

instructions on page 4.

NOTE

Used oil must be disposed of at a proper

collection center.

• Change oil after first 2 operating hours and every 25

operating hours thereafter; more often if operated in

extremely dusty or dirty conditions. Engine should

still be warm but not hot from recent use.

7. Install oil drain plug and tighten

securely.

8. Fill with recommended oil. See "III. Oil and Fuel Speci-

fications" instructions on page 3. See Table 1 on page

3 and Figure 2 on page 2.

1. Be sure you find the correct drain plug location, if pro-

vided. See Figure 30.

9. Wipe away any spilled oil.

2. Disconnect spark plug wire and keep it away from

spark plug. See "G. Avoid Accidental Starts" instruc-

tions on page 2.

10. Carefully disconnect spark plug wire from grounding

post, if provided.

• Keep the disconnected spark plug wire securely

away from metal parts where arcing could occur.

• Attach the spark plug wire to the grounding post, if

provided.

11. Carefully re-connect spark plug wire to spark plug. See

Figure 3 on page 2.

Page 12

Four-Cycle Engine • L-Head • Horizontal Crankshaft • Air-Cooled

Download from Www.Somanuals.com. All Manuals Search And Download.

181-630-14

B. Removing Debris from Engine

Before each use, remove grass clippings, dirt and debris

from the following areas:

• Levers and Linkage

• Cooling Fins

• Air Intake Screen

• Guards

Removing debris will facilitate adequate cooling, correct

engine speed and reduce the risk of fire. See Figure 31.

C. Spark Plug

Check spark plug yearly or every 100 operating hours.

1. Clean area around spark plug.

2. Remove and inspect spark plug.

1. Levers and Linkage

2. Air Intake Screen

3. Muffler Guard

3. Replace spark plug if porcelain is cracked or if elec-

trodes are:

• Pitted

4. Cooling Fins

• Burned

5. Flywheel Guard

• Fouled with deposits

4. Check electrode gap with wire feeler gauge and set

gap to .030 in. (0.76mm) if necessary. See Figure 32.

Figure 31. Debris Removal Areas

5. Install spark plug and tighten securely.

NOTE

A resistor spark plug must be used for replacement. Contact

your Authorized Tecumseh Servicing Dealer for a

Tecumseh Resistor Spark Plug.

D. Cleaning/Replacing Air Cleaner

Your engine has an air cleaner which helps prevent

premature engine wear and failure. NEVER run engine

without complete air cleaner installed on engine. Your air

cleaner periodically needs to be cleaned or replaced. To do

this, you first need to determine the type of air cleaner on

your engine. Your engine will be equipped with one of the

following air cleaners; Type A or B. Follow instructions for

the air cleaner type that resembles your model. See Figure

33 and Figure 34.

1. .030 in. (0.76 mm) Gap

2. Electrodes

3. Porcelain

Figure 32. Resistor Spark Plug

NOTE

DO NOT oil foam pre-filter.

NOTE

Contact your Authorized Tecumseh Servicing Dealer for

Tecumseh Air Cleaner.

4. Replace foam pre-filter onto paper filter.

II. Servicing Paper Filters

I. Servicing Foam Filters

Paper filters cannot be cleaned and must be replaced once

a year or every 100 operating hours; more often if used in

extremely dusty conditions. Replacement filters are

available at a Authorized Tecumseh Servicing Dealer.

Follow the instructions next to the drawing of your air

cleaner to remove and replace it.

Clean foam pre-filter every 3 months or every 25 operating

hours. Clean daily if used in extremely dusty conditions.

After removing the pre-filter, follow these cleaning

instructions below:

1. Wash in warm water and detergent solution then press

(DO NOT twist) until all dirt is removed.

NOTE

DO NOT put oil on or clean a paper filter.

2. Rinse thoroughly until water is clear.

3. Wrap in a clean cloth and press (DO NOT twist) until

completely dry.

181-630-14

Four-Cycle Engine • L-Head • Horizontal Crankshaft • Air-Cooled

Download from Www.Somanuals.com. All Manuals Search And Download.

Page 13

III. Filter Removal/Installation

1. Remove wing nut. See Figure 33 or 34.

2. Remove Cover.

3. Remove optional foam pre-filter, if present (see equip

ment manufacturers instructions) from outside of paper

filter.

4. Remove paper filter element from base.

5. Inspect filters for discoloration or dirt accumulation. If

either is present, see "I. Servicing Foam Filters"

instructions on page 13. See "II. Servicing Paper Fil-

ters" instructions on page 13.

6. Clean inside of base and cover thoroughly.

7. Install paper filter element onto body.

1. Wing Nut

2. Cover

8. Install foam pre-filter, if present (see equipment manu-

facturer’s instructions) over paper element.

3. Foam Pre-Filter

4. Paper Filter

5. Body

9. Install cover over filters.

E. Alternator (Optional)

For alternator related electrical problems such as:

• Inoperative starter

Figure 33. Air Cleaner “A”

• Discharged battery

• Fuse replacement

• Alternator maintenance/repairs

See your equipment manufacturer’s instructions and an

Authorized Tecumseh Servicing Dealer.

F. Carburetor

If you think your carburetor needs adjusting, see your

nearest Authorized Tecumseh Servicing Dealer. Engine

performance should not be affected at altitudes up to 7,000

feet (2,134 meters). For operation at higher elevations,

contact your Authorized Tecumseh Servicing Dealer.

G. Engine Speed

To avoid serious injury or death, DO NOT modify engine in

any way. Tampering with the governor setting can lead to a

runaway engine and cause it to operate at unsafe speeds.

NEVER tamper with factory setting of engine governor.

1. Wing Nut

2. Cover

3. Foam Pre-Filter

4. Paper Filter

5. Body

Running the engine faster than the speed set at the factory

can be dangerous and will VOID THE ENGINE

WARRANTY.

Figure 34. Air Cleaner “B”

H. Adjustments

Do not make any engine adjustments. Factory settings are

satisfactory for most conditions. If adjustments are needed,

contact your Authorized Tecumseh Servicing Dealer.

Page 14

Four-Cycle Engine • L-Head • Horizontal Crankshaft • Air-Cooled

Download from Www.Somanuals.com. All Manuals Search And Download.

181-630-14

VIII. Transporting Your Engine

IX. Storing your Engine

A. Short Term/Seasonal Storage

I. Clean Engine

NEVER transport this engine inside

another vehicle or in any enclosed

WARNING

space if there is any gasoline in the tank. Fuel vapor or

spilled fuel may ignite.

Before servicing the engine remove the blower housing. In

addition, remove grass clippings, dirt and debris from the

following areas:

If there is fuel in the fuel tank, close

WARNING

the fuel shut off valve, if equipped,

and transport the engine upright in an open vehicle, such

as an open trailer or open bed of a pickup truck.

• Cooling fins

• Air intake screen

• Levers

If you do not have an open vehicle and have to transport

the engine upright in a closed vehicle, follow these steps

for emptying the fuel tank before transporting:

• Linkage

1. Empty fuel tank by using a commercially available suc-

tion device designed for use with gasoline.

• Guards

• Carburetor

• Head

DO NOT pour fuel from engine or

siphon fuel by mouth.

WARNING

Removing debris will facilitate adequate cooling, correct

engine speed and reduce the risk of fire.

2. Drain fuel into an approved red GASOLINE container,

being careful to avoid spilling.

I. Fuel Storage

3. Run the engine until remaining fuel is consumed.

NEVER leave the engine

unattended when it is running and

NEVER store engine with fuel in fuel

WARNING

tank inside a building with potential

sources of ignition such as hot water and space heaters,

clothes dryers, electric motors, etc. Failure to do so may

result in an explosion and result in death or serious injury.

NEVER run engine in enclosed areas.

NOTES

If engine fuel stored in the gas tank and/or an approved gas

container is to be unused without gasoline stabilizer for

more than 15-30 days, prepare it for short term/seasonal

storage. See "III. Fuel Treatment" instructions on page 16.

If engine fuel is to be stored for more than one season,

without gasoline stabilizer, it will gradually deteriorate. Also,

if it is stored in the engine’s gas tank without gasoline

stabilizer it is likely that your carburetor will have gum

deposits, a clogged fuel system and will void your warranty.

Prepare the fuel for extended storage. See "B. Extended

Storage" instructions on page 16,

If you operate the engine during all 4 seasons, it is not

necessary to lubricate the cylinder bore.

181-630-14

Four-Cycle Engine • L-Head • Horizontal Crankshaft • Air-Cooled

Download from Www.Somanuals.com. All Manuals Search And Download.

Page 15

II. Fuel System

B. Extended Storage

I. Draining Fuel

To avoid stale gas and carburetor problems, treat the fuel

system in the following method below:

NOTES

Clean debris from engine before draining fuel from

carburetor. See "I. Clean Engine" instructions on page 15,

Tecumseh recommends using ULTRA-FRESH™

Gasoline Stabilizer plus Fuel System Cleaner as an

acceptable method of minimizing formation of fuel gum

deposits during storage. This product is available from your

Authorized Tecumseh Servicing Dealer.

If you have prepared your fuel for short term storage it is not

necessary to drain fuel that contains stabilizer from your

carburetor. See "A. Short Term/Seasonal Storage"

instructions on page 15.

Always follow mix ratio found on stabilizer container. Failure

to do so may result in equipment damage.

To avoid severe injury or death,

WARNING

It is not necessary to drain stabilized gas from carburetor.

DO NOT pour fuel from engine or

siphon fuel by mouth.

III. Fuel Treatment

1. To prevent serious injury from fuel fires, empty fuel tank

by running engine until it stops from lack of fuel. DO

NOT attempt to pour fuel from engine.

1. Add fuel stabilizer according to manufacturer’s

instructions.

2. Run engine at least 10 minutes after adding stabilizer

to allow it to reach carburetor.

2. Run the engine while waiting until the remaining fuel is

consumed.

NEVER store the engine with fuel in

NEVER leave the engine

unattended when it is running and

WARNING

the fuel tank inside a building with

potential sources of ignition such as hot water and space

heaters, clothes dryers, electric motors, etc.

NEVER run engine in enclosed areas.

3. Begin servicing the cylinder bore. See "IV. Oil Cylinder

Bore" instructions on page 17.

NOTE

Instead of using a fuel preservative/stabilizer, you can

empty the fuel tank as described under I. Draining Fuel

instructions. See "B. Extended Storage" instructions.

II. Oil

Change oil if not changed within the last 3 months. See "A.

Checking Oil Level" instructions on page 4.

III. Battery

See equipment manufacturer’s instructions for proper

battery storage if machine is equipped with a battery.

Page 16

Four-Cycle Engine • L-Head • Horizontal Crankshaft • Air-Cooled

Download from Www.Somanuals.com. All Manuals Search And Download.

181-630-14

IV. Oil Cylinder Bore

When lubricating cylinder bore, fuel

may spray from spark plug hole. To

WARNING

prevent serious injury from fuel fires, follow these

instructions:

1. Disconnect spark plug wire and keep it away from

spark plug. See "G. Avoid Accidental Starts" instruc-

tions on page 2. See Figure 35.

• Keep the disconnected spark plug wire

securely away from metal parts where arcing

could occur.

Figure 35. Disconnecting/Connecting Spark Plug

• Attach the spark plug wire to the grounding

post, if provided. See Figure 36.

2. Remove spark plug.

3. Squirt 1oz. (30ml) of clean engine oil into spark plug

hole.

4. Cover spark plug hole with rag to prevent fuel from

spraying from spark plug hole when starter rope is

pulled.

NOTES

For engines equipped with recoil starters proceed to Step 5.

For engines equipped with electric starters proceed to Step

Figure 36. Typical Spark Connection

5. Grasp starter cord handle and pull out slowly using a

full arm stroke. Repeat once. (This will distribute oil

throughout the cylinder to prevent corrosion during

storage.) Proceed to Step 8.

X. Preventing Forest, Brush and Grass

Fires

Local, state and federal laws may require use of a spark

arrester to prevent fires. For example, it is a violation of

California Public Resources Code (section 4442) to use or

operate engine on any forest-covered, brush-covered or

unimproved grass-covered land unless engine is equipped

with a spark arrester. Spark arrester must be maintained in

effective working order by owner and/or operator.

6. Push starter button or turn ignition switch key (see

equipment manufacturer’s instructions) to cycle the

engine for one to two seconds.

7. Turn ignition switch key to “OFF” position. Repeat Step

6 and Step 7. (This will distribute oil throughout the cyl-

inder to prevent corrosion during storage.)

8. Remove rag covering spark plug hole and install spark

plug.

To determine if your engine has a spark arrester, locate the

muffler on your engine. For example, the muffler discharge

will have a spark arrester cover that reads “Tecumseh

Screen Type 36085”.

9. Carefully disconnect spark plug wire from grounding

post, if provided. See Figure 36.

If your engine does not have a spark arrester, you may

purchase one from your Authorized Tecumseh Servicing

Dealer. In some cases the muffler may need to be replaced

to allow the spark arrester to be installed.

NOTE

Connect spark plug wire before attempting to start engine

once engine is out of storage.

181-630-14

Four-Cycle Engine • L-Head • Horizontal Crankshaft • Air-Cooled

Download from Www.Somanuals.com. All Manuals Search And Download.

Page 17

Every 25 Hours or 3 Months Scheduled Maintenance

1. Change Oil

2. Clean Foam Pre-Filter

XI. Maintenance Intervals

Maintenance is one of the most important things that you

can do to extend the life of your Tecumseh Engine. If you

are unable to perform maintenance intervals yourself,

contact your nearest Authorized Tecumseh Servicing

Dealer. You may also call Tecumseh Power company at

1-800-558-5402 or visit www.TecumsehPower.com to

locate your dealer.

Date_______________Owner/Dealer

ALWAYS promptly follow maintenance intervals listed. See

Table 3.

Table 3. Maintenance Intervals

Procedure

Time

After first 2 hrs.

when engine is warm

Change Oil

5 hrs. or Before Each Use

25 hrs. or 3 mos.

Check Oil Level

Clean Cooling Fins

ChangeOil

25 hrs. or 3 mos.

Clean Foam Pre-Filter

100 hrs. or

seasonally

Replace Paper Filter

Element

100 hrs. or

seasonally

Check Spark Plug

200 hrs. or

seasonally

Replace Spark Plug

First Scheduled Maintenance

After First 2 Hours When Engine is Warm

1. Change Oil

Date_______________Owner/Dealer

Before Each Use Scheduled Maintenance

Every 5 Hours or Before Each Use

1. Check Oil Level

2. Clean Cooling Fins

Date_______________Owner/Dealer

Page 18

Four-Cycle Engine • L-Head • Horizontal Crankshaft • Air-Cooled

Download from Www.Somanuals.com. All Manuals Search And Download.

181-630-14

Every 100 Hours or Seasonally Scheduled Maintenance

1. Replace Paper Filter Element

2. Check Spark Plug

Every 200 Hours or Seasonally Scheduled Maintenance

1. Replace Spark Plug

Date_______________Owner/Dealer

181-630-14

Four-Cycle Engine • L-Head • Horizontal Crankshaft • Air-Cooled

Download from Www.Somanuals.com. All Manuals Search And Download.

Page 19

CALIFORNIA & US EPA EMISSION CONTROL WARRANTY STATEMENT

The U. S. Environmental Protection Agency (“EPA”), the

California Air Resources Board (“CARB”) and Tecumseh Power

Company are pleased to explain the Federal and California

Emission Control Systems Warranty on your new small off-road

engine. In California, new 1995 and later small off-road engines

must be designed, built and equipped to meet the State’s

stringent anti-smog standards. In other states, new 1997 and later

model year engines must be designed, built and equipped, at the

time of sale, to meet the U.S. EPA regulations for small non-road

engines. Tecumseh Power Company will warrant the emission

control system on your small off-road engine for the periods of

time listed below, provided there has been no abuse, neglect,

unapproved modification, or improper maintenance of your small

off-road engine.

You are responsible for presenting your small off-road engine to a

Tecumseh Authorized Service Outlet (any Tecumseh Registered

Service Dealer, Tecumseh Authorized Service Distributor or

Tecumseh Central Warehouse Distributor) as soon as a problem

exists. The warranty repairs should be completed in a reasonable

amount of time, not to exceed 30 days.

Warranty service can be arranged by contacting either an

Authorized Tecumseh Servicing Dealer and/or Tecumseh Power

Company, c/o Service Manager, 900 North Street, Grafton, WI

53024-1499. Telephone 1-262-377-2700 [or in USA/Canada call

1-800-558-5402].

IMPORTANT NOTE

This warranty statement explains your rights and obligations

under the Emission Control System Warranty (“ECS Warranty”)

which is provided to you by Tecumseh Power Company pursuant

to California law. Tecumseh Power Company also provides to

original purchasers of new Tecumseh Power Company engines

the Tecumseh Power Company Limited Warranties for New

Tecumseh Engines and Electronic Ignition Modules. The

Tecumseh Power Company Limited Warranties for New

Tecumseh Engines and Electronic Ignition Modules (“Tecumseh

Power Company Warranty”) are located on the back cover of the

Operator’s Manual, enclosed with all new Tecumseh Power

Company engines. The ECS Warranty applies only to the

emission control system of your new engine. To the extent that

there is any conflict in terms between the ECS Warranty and the

Tecumseh Power Company Warranty, the ECS Warranty shall

apply except in any circumstances in which the Tecumseh Power

Company Warranty may provide a longer warranty period. Both

the ECS Warranty and the Tecumseh Power Company Warranty

describe important rights and obligations with respect to your new

engine.

Your emission control system may include parts such as the

carburetor, air cleaner assembly, ignition system, exhaust system,

crankcase breather assembly and, the evaporative control

system. Also included may be the compression release system

and other emission-related assemblies.

Where

warrantable condition exists, Tecumseh Power

Company will repair your small off-road engine at no cost to you

for diagnosis, parts and labor.

MANUFACTURER’S EMISSION CONTROL

SYSTEM WARRANTY COVERAGE

Emission control systems on 1995 and later model year California

small off-road engines are warranted for two years as hereinafter

noted. In other states, 1997 and later model year engines are also

warranted for two years. If, during such warranty period, any

emission-related part on your engine is defective in materials or

workmanship, the part will be repaired or replaced by Tecumseh

Power Company

Warranty service can only be performed by a Tecumseh Power

Company Authorized Servicing Dealer. At the time of requesting

warranty service, evidence must be presented of the date of sale

to the original purchaser. The purchaser shall pay any charges for

making service calls and/or for transporting the products to and

from the place where the inspection and/or warranty work is

performed. The purchaser shall be responsible for any damage or

loss incurred in connection with the transportation of any engine

or any part(s) thereof submitted for inspection and/or warranty

work.

OWNER’S WARRANTY RESPONSIBILITIES

As the small off-road engine owner, you are responsible for the

performance of the required maintenance listed in your Operator’s

Manual, but Tecumseh Power Company will not deny warranty

solely due to the lack of receipts or for your failure to provide

written evidence of the performance of all scheduled

maintenance.

As the small off-road engine owner, you should, however, be

aware that Tecumseh Power Company may deny you warranty

coverage if your small off-road engine or a part thereof has failed

due to abuse, neglect, improper maintenance or unapproved

modifications.

If you have any questions regarding your warranty rights and

responsibilities, you should contact Tecumseh Power Company at

1-262-377-2700 or in USA/Canada call 1-800-558-5402.

Revised July, 2005

IMPORTANT!

The emission Regulations may be different for your country. The emissions Control Warranty Statement is only applicable

to engines with an emissions compliance statement and decal that references “Emissions Regulations”.

Page 20

Four-Cycle Engine • L-Head • Horizontal Crankshaft • Air-Cooled

Download from Www.Somanuals.com. All Manuals Search And Download.

181-630-14

EMISSION CONTROL SYSTEM WARRANTY

Emission Control System Warranty (“ECS Warranty”) for 1995

and later model year California small off-road engines (for other

states, 1997 and later model year engines):

5. The owner shall not be charged for diagnostic labor which

leads to the determination that a part covered by the ECS

Warranty is in fact defective, provided that such diagnostic

work is performed at a Tecumseh Authorized Service

Outlet.

A. APPLICABILITY: This warranty shall apply to 1995 and later

model year California small off-road engines (for other states,

1997 and later model year engines). The ECS Warranty

Period shall begin on the date the new engine or equipment is

delivered to its original, end-use purchaser, and shall continue

for 24 consecutive months thereafter.

6. Tecumseh Power Company shall be liable for damages to

other original engine components or approved

modifications proximately caused by a failure under

warranty of an emission-related part covered by the ECS

Warranty.

B. GENERAL EMISSIONS WARRANTY COVERAGE:

Tecumseh Power Company warrants to the original, end-use

purchaser of the new engine or equipment and to each

subsequent purchaser that each of its small off-road engines

is:

7. Throughout the ECS Warranty Period, Tecumseh Power

Company shall maintain a supply of warranted emission-

related parts sufficient to meet the expected demand for

such emission-related parts.

1. Designed, built and equipped so as to conform with all

applicable regulations adopted by the Air Resources

Board pursuant to its authority in Chapters 1 and 2, Part 5,

Division 26 of the Health and Safety Code, and

8. Any Tecumseh Power Company authorized and approved

emission-related replacement part may be used in the

performance of any ECS Warranty maintenance or repair

and will be provided without charge to the owner. Such

use shall not reduce Tecumseh Power Company ECS

Warranty obligations.

2. Free from defects in materials and workmanship which, at

any time during the ECS Warranty Period, will cause a

warranted emissions-related part to fail to be identical in all

material respects to the part as described in the engine

manufacturer’s application for certification.

9. Unapproved add-on or modified parts may not be used to

modify or repair a Tecumseh Power Company engine.

Such use voids this ECS Warranty and shall be sufficient

grounds for disallowing an ECS Warranty claim.

Tecumseh Power Company shall not be liable hereunder

for failures of any warranted parts of a Tecumseh Power

Company engine caused by the use of such an

unapproved add-on or modified part.

C. THE ECS WARRANTY ONLY PERTAINS TO EMISSION-

RELATED PARTS ON YOUR ENGINE AS FOLLOWS:

1. Any warranted, emissions-related parts which are not

scheduled for replacement as required maintenance in the

Operator’s Manual shall be warranted for the ECS

Warranty Period. If any such part fails during the ECS

Warranty Period, it shall be repaired or replaced by

Tecumseh Power Company according to Subsection 4

below. Any such part repaired or replaced under the ECS

Warranty shall be warranted for any remainder of the ECS

Warranty Period.

EMISSION-RELATED PARTS INCLUDE THE FOLLOWING:

1. Carburetor Assembly including internal components:

a) Carburetor gaskets

b) Intake pipe

2. Air Cleaner Assembly including components:

a) Air filter element

2. Any warranted, emissions-related part which is scheduled

only for regular inspection as specified in the Operator’s

Manual shall be warranted for the ECS Warranty Period. A

statement in such written instructions to the effect of

“repair or replace as necessary”, shall not reduce the ECS

Warranty Period. Any such part repaired or replaced under

the ECS Warranty shall be warranted for the remainder of

the ECS Warranty Period.

3. Ignition System including components:

a) Spark plug

b) Ignition module

c) Flywheel assembly

4. Exhaust System including components:

3. Any warranted, emissions-related part which is scheduled

for replacement as required maintenance in the Operator’s

Manual, shall be warranted for the period of time prior to

the first scheduled replacement point for that part. If the

part fails prior to the first scheduled replacement, the part

shall be repaired or replaced by Tecumseh Power

Company according to Subsection 4 below. Any such

emissions-related part repaired or replaced under the ECS

Warranty, shall be warranted for the remainder of the ECS

Warranty Period prior to the first scheduled replacement

point for such emissions-related part.

a) Catalytic muffler (if so equipped)

b) Muffler gasket (if so equipped)

c) Exhaust manifold (if so equipped)

5. Crankcase Breather Assembly including components

a) Breather connection tube

6. Evaporative Control System including components:

a) Fuel line(s)

b) Fuel filter

4. Repair or replacement of any warranted, emissions-

related part under this ECS Warranty shall be performed

at no charge to the owner at a Tecumseh Authorized

Service Outlet.

c) Canister (if so equipped)

d) Fuel tank (if so equipped)

e) Fuel fill cap (if so equipped)

IMPORTANT!

Revised July, 2005

The emission Regulations may be different for your country. The emissions Control Warranty Statement is only applicable

to engines with an emissions compliance statement and decal that references “Emissions Regulations”.

181-630-14

Four-Cycle Engine • L-Head • Horizontal Crankshaft • Air-Cooled

Download from Www.Somanuals.com. All Manuals Search And Download.

Page 21

XII. Warranty Information

LIMITED WARRANTY FOR NEW TECUMSEH ENGINES

AND ELECTRONIC IGNITION MODULES

For the time period shown below from the date of purchase and subject to the exceptions and limitations described herein, Tecumseh Power Company will, at its option as

the exclusive remedy, either repair or replace for the original purchaser, free of charge, any part of any new Tecumseh engine which is found, upon examination by any

Authorized Tecumseh Servicing Outlet or by Tecumseh’s factory in Grafton, Wisconsin, to be DEFECTIVE IN MATERIAL AND/OR WORKMANSHIP. This Limited

Warranty DOES NOT COVER (i) any Tecumseh engine or part(s) thereof used to power any vehicle in competitive racing and/or used on any commercial or rental track, or

(ii) defects or damage caused by alterations or modifications of new Tecumseh engines or parts or by normal wear, accidents, improper maintenance, improper use or

abuse of the product, or failure to follow the instructions contained in an Instruction Manual for the operation of the new Tecumseh engine or part. The cost of normal

maintenance or replacement of service items which are not defective shall be paid for by the original purchaser. At the time warranty service is requested, evidence must

be presented of the date of purchase by the original purchaser. Any charge for making service calls and/or for transporting any engine or part(s) thereof to and from the

place where the inspection and/or warranty work is performed is payable solely by the purchaser. The purchaser is responsible for any damage or loss incurred in

connection with the transportation of any engine or part(s) thereof submitted for inspection and/or warranty work. WARRANTY SERVICE CAN ONLY BE PERFORMED

BY A TECUMSEH AUTHORIZED SERVICE OUTLET. Warranty service can be arranged by contacting a Tecumseh Authorized Service Outlet (any Tecumseh Registered

Service Dealer, Tecumseh Authorized Service Distributor, or Tecumseh Central Warehouse Distributor) or by contacting Tecumseh c/o Service Manager, 900 North Street,

Grafton, Wisconsin 53024-1499.

(4)

(5)

“CONSUMER USE”

“COMMERCIAL USE”

Warranty