Turntable System
Operating Instructions
Model No. SL-1200MK5
SL-1210MK5
SL-1200MK5
Before connecting, operating or adjusting this prod-
uct, please read these instructions completely.
Please keep this manual for future reference.
PP
RQT7018-1Y
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
Read these operating instructions carefully before using the unit. Follow the safety instructions on the unit and the applicable safety instructions
listed below. Keep these operating instructions handy for future reference.
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
11) Only use attachments/accessories specified by the manufac-
turer.
12) Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer, or sold with
the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to
avoid injury from tip-over.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
13) Unplug this apparatus during lightning storms or when unused
for long periods of time.
7) Do not block any ventilation openings. Install in accordance with
the manufacturer’s instructions.
14) Refer all servicing to qualified service personnel. Servicing is
required when the apparatus has been damaged in any way,
such as power-supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does not operate normal-
ly, or has been dropped.
8) Do not install near any heat sources such as radiators, heat reg-
isters, stoves, or other apparatus (including amplifiers) that pro-
duce heat.
9) Do not defeat the safety purpose of the polarized or grounding-
type plug. A polarized plug has two blades with one wider than
the other. A grounding-type plug has two blades and a third
grounding prong. The wide blade or the third prong are provided
for your safety. If the provided plug does not fit into your outlet,
consult an electrician for replacement of the obsolete outlet.
10) Protect the power cord from being walked on or pinched particu-
larly at plugs, convenience receptacles, and the point where
they exit from the apparatus.
THE FOLLOWING APPLIES ONLY IN THE U.S.A.
CAUTION:
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules.
These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more
of the following measures:
¡Reorient or relocate the receiving antenna.
¡Increase the separation between the equipment and re-
ceiver.
¡Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
¡Consult the dealer or an experienced radio/TV technician
for help.
Any unauthorized changes or modifications to this
equipment would void the user’s authority to operate this
device.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation.
3
RQT7018
Download from Www.Somanuals.com. All Manuals Search And Download.
Features
Controls
A masterpiece amongst turntables with a worldwide repu-
tation.
Highly accurate turntable speed maintained continuously
with a quartz pitch control.
•The pitch can be varied throughout the range maintaining perfect
accuracy.
•Pitch can be instantly reset to the rated speed (33 1/3 or 45 r/min)
with the reset button.
The direct drive produces high torque.
•Wow and flutter below 0.01 %. Starting torque of 1.5 kg-cm en-
abling the turntable to reach 33 1/3 r/min in 0.7 seconds.
•Smooth stops are achieved with a fully electronic braking system.
The braking speed can be adjusted with the brake speed control
knob.
-8
6
4
2
+8
2
Tone arm with gimbal suspension
•Using the balance weight control measurement units on the tone
arm, you can quickly change stylus pressure settings to the appro-
priate pressure.
4
6
+8
•Stylus skipping can be reduced using horizontal weight control for
scratch play.
•The tone arm can be finely adjusted in a range of 6 millimeters
with the lockable height control.
Anti-vibration design with 3 layer cabinet construction
No.
Name
Reference page(s)
and large insulating legs.
EP record adaptor . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Turntable base . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Turntable mat (Or disc slip sheet) . . . . . . . . . . . . . . 5
Turntable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Center spindle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Strobe mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Power switch (power) . . . . . . . . . . . . . . . . . . . . . . . . 8
Strobe light, pilot lamp . . . . . . . . . . . . . . . . . . . . . . . 8
Start-stop button (start-stop) . . . . . . . . . . . . . . . . . . 8
Speed select buttons (33, 45) . . . . . . . . . . . . . . . . . . 8
Shell stand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Arm-height control . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Balance weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Stylus pressure control . . . . . . . . . . . . . . . . . . . . . . . 6
Arm lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Anti-skating control . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Cue lever . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Arm clamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Arm rest . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Tone arm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Pitch indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Pitch control (pitch adj.) . . . . . . . . . . . . . . . . . . . . . . 9
Reset button (reset) . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Locking nut . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Head shell . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Stylus light switch . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Stylus light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Pop-up stylus light.
•A light illuminates the stylus.
Preparation of the cartridge
1 Attach a cartridge (not included).
Follow the cartridge’s instructions to correctly attach it to the
head shell.
•Use the included shell weight when using a light cartridge
(3.5 to 6.5 grams).
Screws
Head shell
Shell
weight
Lead wire
Terminal
Cartridge
Stylus
2 Adjust the overhang.
Fit the included overhang gauge to the head shell. Adjust the
overhang and facing of the cartridge and tighten the screws.
•Line the stylus tip up with the end of the gauge.
•The cartridge should be parallel on the shell head.
Screws
Overhang
gauge
Stylus tip
52 mm
4
RQT7018
Download from Www.Somanuals.com. All Manuals Search And Download.
Putting the player together
In order to prevent damage during shipping some of the equipment
has been disassembled.
Put the player together in the following order.
•Do not connect the AC power supply cord until set up is complete.
•Leave the dust cover off until set up and adjustments are com-
plete.
1 Fit the turntable and turntable mat.
Put the turntable on the center spindle and then lay the mat
on top.
•Be very careful when putting the turntable on the main unit.
The magnet on the bottom of the turntable is finely adjusted
and sharp contact can cause it to move and lead to poor
operation. Ensure the magnet remains free from dust and
iron particles.
•Do not adjust the screws attaching the magnet to the turn-
table. The rated performance of the unit cannot be guaran-
teed if the magnet is moved.
1
Turntable mat
2 Attach the head shell.
Fit the head shell into the tone arm, keep it horizontal and
tighten the locking nut.
Turntable
Magnet
Locking nut
Head shell
Screws
3 Attach the balance weight to the rear
Center spindle
3
of the tone arm.
2
Tone arm
If the cartridge weighs between 10 and 13 grams, attach the
included auxiliary weight to the main balance weight.
Balance weight
Auxiliary weight
Connections and installation
Connecting to an amplifier and AC power supply cord
1. Connect the PHONO earth lead and stereo PHONO
cables to the amplifier PHONO terminals.
Amplifier
(not included)
SIGNAL GND
PHONO
White (L)
Red (R)
This unit
TUNER
Stereo connection cable
•If the earth lead isn’t connected, a hum will be heard from the
AC power source.
•You will not have adequate volume or sound quality if connect-
ing to an amplifier that has no PHONO terminals.
(L) (R)
To household
AC outlet
1
1
2. Connect the AC power supply cord.
Earth lead
Stereo connection cable
•Connect this cord only after all other connections are complete.
•Confirm the wattage of AC outlets on amplifiers and receivers
before using them for this unit. This unit consumes 13.5 W.
2
5
RQT7018
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections and installation
Installation
Connecting to an Audio Mixer (not
included)
•Install the unit on a horizontal surface protected from vibrations.
•Keep this unit as far as possible from speakers.
•Disconnect all units from the power source before making any con-
nections.
•Reconnect the AC power supply cord after all other connections
•Ensure the unit is not exposed to direct sunlight, dust, humidity,
and heat from a heating appliance.
are complete.
Unit
Unit
•This unit may pick up interference from a radio if there is one nearby.
Keep radios as far as possible from this unit.
Earth lead
Adjusting the height of the insulators
Place the unit where it is to be used and adjust the height of the legs
to make the unit horizontal.
Audio mixer
Preparatory adjustments
Horizontal balance and stylus pressure
1 Release the tone arm.
3 Turn the stylus pressure control to “0”
1. Return the tone arm to the arm rest and fix it
with the arm clamp.
1. Remove the stylus cover, taking care not to dam-
age the stylus, then release the arm clamp.
2. Free the tone arm from the arm rest.
2. Turn the stylus pressure control to “0”.
Hold the balance weight still while doing this.
Arm clamp
Balance weight
Turn stylus
pressure
Center line
control
2 Adjust horizontal balance
1. Push the cue lever down.
2. Turn the anti-skating control to “0”.
3. Turn the balance weight until the arm is approxi-
mately horizontal.
Arm clamp
Take care at this time not to allow the stylus to touch the unit.
Balanced
4 Adjust stylus pressure
Too far forward
Too far back
Turn the balance weight to adjust to the appropri-
ate pressure for the cartridge you are using.
See the cartridge’s instructions for recommended stylus pres-
sure.
The stylus pressure control will turn at the same time. Stop
when the center line points to the required pressure.
Arm clamp
Arm rest
Cue lever
Turn
balance
weight
Center line
Anti-skating control
6
RQT7018
Download from Www.Somanuals.com. All Manuals Search And Download.
Preparatory adjustments
Using the balance weight control
Tone arm height
Make note of the balance weight setting for your stylus cartridge,
you can quickly change the stylus pressure without having to re-
adjust the horizontal balance of the arm each time you remove and
re-attach the stylus cartridge.
Released
1. Release the arm lock.
1
Attach the cartridge to the tone arm you are using.
Turn the balance weight control to the setting you previously
used to balance the weight including cartridge.
Turn the stylus pressure control dial to the setting you previ-
ously used to balance the weight including cartridge.
Locked3
2. Adjust the arm height.
•Adjust the ring using the chart
below as reference so the arm
height matches the indicated
height of the cartridge. Mea-
surements are marked on the
arm height control ring in 0.5
millimeter intervals.
Balance weight
measurement units
Index line
Arm height control ring
Cartridge height
(H) in millimeters
Height control
position
17
18
19
20
21
22
23
0
1
2
3
4
5
6
Anti-skating
Adjust the dial to the same value as the stylus pressure
control when playing normal music.
For scratch play
Adjust the control to reduce skipping.
•If you do not know the height of your cartridge, rest the stylus on
a record and adjust the height control until the tone arm and
record are parallel.
Tone arm and record parallel.
3. Lock the arm after adjusting the height.
Armlift height
Preparation
1. Put a record on the turntable.
2. Take off the stylus cover and release the arm clamp.
Fit the dust cover
Hold the dust cover with both hands and fit it over the
player from directly above.
Use a screwdriver to turn the armlift screw.
Make this adjustment only if the cartridge you are using makes it
necessary.
•Turning the screw clockwise lowers the armlift.
•Turning the screw anti-clockwise raises the armlift.
Armlift screw
Armlift
Armlift height (the distance between the record and stylus when the
cue lever is raised) is set to between 8 and 13 millimeters at time of
shipment.
7
RQT7018
Download from Www.Somanuals.com. All Manuals Search And Download.
Playing records
Preparation
1 Turn [power] to turn the unit on.
1. Put a record on the turntable.
•The pilot lamp comes on.
•
2. Take off the stylus cover and release the arm clamp.
33 1/3 r/min is automatically selected and the indicator lights.
•Press [45] if you are playing a 45 r/min record.
Pilot lamp
Indicator
1
2
3
lights
w
33
45
2 Press [start-stop].
The turntable starts revolving.
start•stop
33
3 Press [reset] to light the pitch control
green LED lamp.
4,5
The pitch returns to 33 1/3 or 45 r/min.
Use the above indicated
Green
pitch for playing standard
LED indicator
music.
reset
4 Lift the cue lever and move the tone arm
over the record.
To temporarily stop play
Lift the cue lever.
The stylus lifts off the record.
Refer to page 9 for fine adjustments to the pitch
Cue lever
When using EP records
1. Take the EP record adaptor out
of its holder and fit it over the
center spindle.
EP record adaptor
5 Lower the cue lever.
The tone arm moves down and play starts.
2. Press [45] to change the speed.
When play finishes
1. Lift the cue lever and move the tone arm back to the arm rest.
2. Press [start-stop].
The electronic brake gently stops the turntable.
3. Turn [power] to turn the unit off.
4. Clamp the tone arm and put the stylus cover back on.
When the player is to be used for scratch play.
Use the disc slip sheet instead of the turntable mat. This enables
the record to be easily moved during play.
To light up the stylus
•Press the stylus light switch. The stylus light rises up and illumi-
nates the stylus.
•Top (printed side): Lay the record on this side.
•Bottom: Slippery side.
•When the light is not required, press it down. The light also goes
out.
For a different kind of slip
Put the transparent sheet under
Press the switch firmly. If the switch is lightly pressed, the light may
come on but not rise up.
the disc slip sheet.
Disc slip sheet
Stylus light
Transparent sheet
Stylus light switch
8
RQT7018
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjustments while using the unit
Pitch control
Adjusting the turntable brake speed
Fine adjustment to the number of revolutions per minute.
Brake speed can be adjusted by pressing [start-stop] until the turn-
table stops.
Use a small screwdriver in the hole on the turntable to adjust the
1 Press [reset] to turn off the green LED
light.
brake speed.
S: Slow stop
F: Fast stop
Green
LED indicator
Pitch control
S
BRAKE
F
reset
2 Slide [pitch adj.] while the turntable is
revolving.
Move the control to the required position.
•The numbers represent approximate percentages.
•Pitch can be adjusted between –8 % and +8 %.
To reset pitch to the preset value
Press [reset].
The green LED indicator lights and the pitch immediately returns to
the set value (33 1/3 or 45 r/min), regardless of any adjustments
made with [pitch adj.].
Press [reset] again and pitch returns to the adjusted value.
To measure pitch
The four rows of strobe mirrors around the edge of the turntable can
assist you in measuring pitch.
+
+
6.4 % change in pitch when stationary
3.3 % change in pitch when stationary
Normal turntable speed when stationary
_
3.3 % change in pitch when stationary
They are lit by the strobo light as they pass and each row appears to
stand still at a different pitch.
Strobo light
w
Read the pitch control slider replacement instructions that comes
with this product carefully when replacing the pitch control slider.
9
RQT7018
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
Product service
1. Damage requiring service—The unit should be serviced by
qualified service personnel if:
Care of the parts
(a) The AC power supply cord or AC adaptor has been
damaged; or
(b) Objects or liquids have gotten into the unit; or
(c) The unit has been exposed to rain; or
To clean this unit, wipe with a soft, dry cloth.
•Never use alcohol, paint thinner, or benzine to clean this unit.
•Before using chemically treated cloth, read the instructions that
came with the cloth carefully.
(d) The unit does not operate normally or exhibits a marked
change in performance; or
(e) The unit has been dropped or the cabinet damaged.
2. Servicing—Do not attempt to service the unit beyond that
described in these operating instructions. Refer all other servic-
ing to authorized servicing personnel.
3. Replacement parts—When parts need replacing ensure the
servicer uses parts specified by the manufacturer or parts that
have the same characteristics as the original parts.
Unauthorized substitutes may result in fire, electric shock, or
other hazards.
Do not wipe the dust cover while playing a record.
This can cause static electricity. This static can cause the tone arm
to be attracted towards the cover.
Thoroughly clean dust off the stylus and record.
•
Use a soft brush to clean the stylus. Brush from the base to the tip.
•Use a good quality record cleaner to keep your records clean.
4. Safety check—After repairs or service, ask the servicer to
perform safety checks to confirm that the unit is in proper
working condition.
Head shell
terminals
Product information
Wipe the head shell terminals occasionally.
Use a soft cloth. Turn the amplifier off before fitting or removing the
head shell.
•Damage to your speakers can occur if the head shell is moved
while the volume is turned up.
For product information or assistance with product operation:
In the U.S.A., contact the Panasonic Customer Call Center at 1-
800-211-7262, or e-mail [email protected], or the
website (http://www.panasonic.com).
In Canada, contact the Panasonic Canada Inc. Customer Care Cen-
authorized Servicentre closest to you.
•Leave the stylus cover on while handling the head shell to prevent
damaging the stylus.
Oiling the center spindle.
Apply 2 or 3 drops every 2000 hours of operation. Use SFW0010 oil
(not included).
Oil
Moving the unit
Repackage the unit in the packaging it came in.
If you no longer have the packaging, do the following:
•Return the tone arm to the arm rest and tape it in place.
•Remove the balance weight and head shell from the tone arm and
carefully wrap them.
•Take off the turntable and turntable mat and carefully wrap them.
•Carefully wrap the main unit in a blanket or paper.
10
RQT7018
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting guide
Before requesting service, make the below checks. If you are in doubt about some of the check points, or if the remedies indicated in
the chart do not solve the problem:
In the U.S.A., contact the Panasonic Customer Call Center at 1-800-211-7262, or e-mail [email protected], or the
website (http://www.panasonic.com).
authorized Servicentre closest to you.
Reference
Problem
Probable cause(s)
Suggested remedy
page(s)
5
No power.
Is the AC power supply cord plugged in?
Plug the cord in firmly.
There is power but no sound. Are connections to the amplifier/receiver’s
Sound is weak. PHONO terminals correct?
Connect the stereo pin cables to the amplifier’s
PHONO terminals.
5
5
Left and right sounds are re- Are the stereo connection cable connections
versed. to the amplifier or receiver reversed?
Double check all connections.
Humming heard during play. Are there other appliances or their AC power
Separate the appliances and their AC power
supply cords from this unit.
supply cords near the stereo connection
cable?
Make sure the earth lead is correctly con-
nected.
Is the earth lead connected?
5
Specifications
Turntable section
Type
Tonearm section
Quartz direct drive
Manual turntable
Direct drive
Brushless DC motor
Type
Universal
230 mm (9-1/16")
0 – 6 mm
Effective length
Arm height adjustment range
Overhang
Drive method
Motor
15 mm (19/32")
Turntable platter
Aluminum diecast
Diameter 33.2 cm (13-5/64")
Mass 1.7 kg (3.74 lb.)
Effective mass
Offset angle
Friction
12 g (without cartridge)
22°
Less than 7 mg (lateral, vertical)
Turntable speeds
Variable range pitch
Starting torque
Build-up characteristics
Braking system
33 1/3 r/min, 45 r/min
Tracking error angle
8 %
Within 2° 32' (at the outer groove of 30 cm (12") record)
Within 0° 32' (at the inner groove of 30 cm (12") record)
Stylus pressure adjustment range
Applicable cartridge weight range
1.5 kg·cm (1.3 lb·in)
0.7 s. from standstill to 33 1/3 r/min
Electronic brake
0 – 4 g
3.5 – 13 g
11 – 20.5 g (including headshell)
9.5 – 13 g
17 – 20.5 g (including headshell)
3.5 – 6.5 g
Wow and flutter
0.01 % WRMS\
0.025 % WRMS (JIS C5521)
0.035 % peak (IEC 98A Weighted)
–56 dB (IEC 98A Unweighted)
–78 dB (IEC 98A Weighted)
This rating refers to turntable assembly alone, excluding effects
of record, cartridge or tonearm, but including platter. Measured
by obtaining signal from built-in frequency generator of motor
assembly.
(with auxiliary weight)
(with shell weight)
Headshell weight
Rumble
11 – 14 g (including headshell)
7.5 g
\
General
Power supply
Power consumption
Dimensions (W×H×D)
AC 120 V, 60 Hz
13.5 W
45.3 × 17.2 × 35.5 cm
(17-27/32" × 6-25/32" × 13-31/32")
12 kg (26.4 Ib)
Mass
Specifications are subject to change without notice.
Mass and dimensions are approximate.
11
RQT7018
Download from Www.Somanuals.com. All Manuals Search And Download.
This manual was printed with soy based ink.
Panasonic Consumer Electronics
Company, Division of Panasonic
Corporation of North America
One Panasonic Way Secaucus,
New Jersey 07094
Panasonic Puerto Rico, Inc.
Ave. 65 de Infantería, Km. 9.5
San Gabriel Industrial Park, Carolina,
Puerto Rico 00985
Panasonic Canada Inc.
En
5770 Ambler Drive
Mississauga, Ontario L4W 2T3
2003 Matsushita Electric Industrial Co., Ltd.
Printed in Japan
RQT7018-1Y
M0203TK1124
Download from Www.Somanuals.com. All Manuals Search And Download.
|