Thomson TG576 v7 and TG585 v7
Residential DSL Gateway
CLI Reference Guide R7.4
Download from Www.Somanuals.com. All Manuals Search And Download.
Thomson TG576 v7 and TG585 v7
CLI Reference Guide R7.4
Download from Www.Somanuals.com. All Manuals Search And Download.
Copyright
Copyright © 1999-2007 THOMSON. All rights reserved.
Distribution and copying of this document, use and communication of its contents is not permitted without
written authorization from THOMSON. The content of this document is furnished for informational use only, may
be subject to change without notice, and should not be construed as a commitment by THOMSON. THOMSON
assumes no responsibility or liability for any errors or inaccuracies that may appear in this document.
Thomson Telecom Belgium Prins Boudewijnlaan, 47 B-2650 Edegem Belgium
www.thomson-broadband.com
Trademarks
The following trademarks are used in this document:
>
>
>
>
DECT is a trademark of ETSI.
Bluetooth® word mark and logos are owned by the Bluetooth SIG, Inc.
Wi-Fi® and the Wi-Fi logo are registered trademarks of the Wi-Fi Alliance. "Wi-Fi CERTIFIED", "Wi-Fi ZONE",
"Wi-Fi Alliance", their respective logos and "Wi-Fi Protected Access" are trademarks of the Wi-Fi Alliance.
>
>
Microsoft® , MS-DOS® , Windows® and Windows NT® are either registered trademarks or trademarks of
Microsoft Corporation in the United States and/or other countries.
>
Apple® and Mac OS® are registered trademarks of Apple Computer, Incorporated, registered in the United
States and other countries.
>
>
UNIX® is a registered trademark of UNIX System Laboratories, Incorporated.
Adobe® , the Adobe logo, Acrobat and Acrobat Reader are trademarks or registered trademarks of Adobe
Systems, Incorporated, registered in the United States and/or other countries.
Document Information
Status: v1.0
Reference: E-DOC-CTC-20071119-0014
Short Title: CLI Reference Guide TG576 v7 and TG585 v7 R7.4 (SWv7.4.2.4)
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Contents:
E-DOC-CTC-20071119-0014 v1.0
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
autopvc Commands.....................................................................................67
connection Commands............................................................................... 79
E-DOC-CTC-20071119-0014 v1.0
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
cwmp Commands........................................................................................99
cwmp config...................................................................................................................................... 100
dhcp Commands........................................................................................107
dhcp client debug clear....................................................................................................................111
dhcp client debug stats.................................................................................................................... 112
dhcp client flush................................................................................................................................114
dhcp client iflist................................................................................................................................. 120
dhcp client rqoptions add................................................................................................................ 122
dhcp client txoptions list..................................................................................................................128
dhcp client txoptions optionlist....................................................................................................... 129
dhcp relay debug stats.....................................................................................................................132
dhcp relay debug traceconfig.......................................................................................................... 133
dhcp relay ifconfig............................................................................................................................ 136
dhcp relay iflist..................................................................................................................................137
E-DOC-CTC-20071119-0014 v1.0
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
dhcp relay list.................................................................................................................................... 138
dhcp relay modify............................................................................................................................. 139
dhcp relay ruleadd............................................................................................................................ 140
dhcp relay ruledelete........................................................................................................................ 141
dhcp rule debug traceconfig............................................................................................................143
dhcp rule list......................................................................................................................................146
dhcp server config............................................................................................................................ 147
dhcp server debug traceconfig........................................................................................................150
dhcp server option flush.................................................................................................................. 156
dhcp server option instadd.............................................................................................................. 157
dhcp server option instdelete.......................................................................................................... 158
dhcp server option tmpllist..............................................................................................................164
dhcp server pool list.........................................................................................................................171
dhcp server pool optadd..................................................................................................................172
dhcp server pool optdelete.............................................................................................................. 173
dhcp server pool rtadd.....................................................................................................................174
dhcp server pool rtdelete.................................................................................................................175
E-DOC-CTC-20071119-0014 v1.0
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
dhcp server pool ruleadd.................................................................................................................176
dhcp server pool ruledelete............................................................................................................. 177
dhcp spoofing add............................................................................................................................ 178
dhcp spoofing attach........................................................................................................................ 179
dhcp spoofing config........................................................................................................................180
dhcp spoofing delete........................................................................................................................ 182
dhcp spoofing detach....................................................................................................................... 183
dhcp spoofing flush.......................................................................................................................... 184
dhcp spoofing option-add................................................................................................................186
dhcp spoofing option-delete............................................................................................................187
dns Commands.......................................................................................... 189
dns client config................................................................................................................................190
dns client dnsadd..............................................................................................................................191
dns client dnsdelete..........................................................................................................................192
dns client dnslist............................................................................................................................... 193
dns client flush.................................................................................................................................. 194
dns client nslookup...........................................................................................................................195
dns server debug spoof clear..........................................................................................................198
dns server debug spoof list............................................................................................................. 201
dns server debug stats.....................................................................................................................203
dns server host add..........................................................................................................................205
dns server host delete......................................................................................................................206
dns server host flush........................................................................................................................207
E-DOC-CTC-20071119-0014 v1.0
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
dsd Commands.......................................................................................... 213
dsd debug config.............................................................................................................................. 215
dsd debug connection list................................................................................................................216
dsd debug proxy............................................................................................................................... 217
dsd debug stats.................................................................................................................................219
dsd intercept config.......................................................................................................................... 220
dsd syslog config.............................................................................................................................. 221
dsd urlfilter rule add.........................................................................................................................224
dsd urlfilter rule delete.....................................................................................................................225
dsd urlfilter rule flush.......................................................................................................................226
dyndns add........................................................................................................................................ 230
dyndns delete.................................................................................................................................... 231
dyndns flush...................................................................................................................................... 232
dyndns host list.................................................................................................................................236
dyndns service list............................................................................................................................ 239
env Commands.......................................................................................... 241
env list................................................................................................................................................244
env set................................................................................................................................................245
E-DOC-CTC-20071119-0014 v1.0
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
eth bridge add................................................................................................................................... 251
eth bridge clear................................................................................................................................. 252
eth bridge config...............................................................................................................................253
eth bridge delete............................................................................................................................... 254
eth bridge dynvlan add.................................................................................................................... 256
eth bridge dynvlan config................................................................................................................ 257
eth bridge dynvlan delete................................................................................................................ 258
eth bridge dynvlan flush.................................................................................................................. 259
eth bridge flush................................................................................................................................. 261
eth bridge ifadd.................................................................................................................................262
eth bridge ifattach.............................................................................................................................263
eth bridge ifdelete.............................................................................................................................266
eth bridge ifdetach............................................................................................................................267
eth bridge ifflush...............................................................................................................................268
eth bridge iflist.................................................................................................................................. 269
eth bridge igmpsnooping config.....................................................................................................271
eth bridge macadd............................................................................................................................276
eth bridge macdelete........................................................................................................................277
eth bridge maclist............................................................................................................................. 278
eth bridge rule add........................................................................................................................... 279
eth bridge rule delete....................................................................................................................... 280
eth bridge rule flush......................................................................................................................... 281
eth bridge unknownvlan iflist.......................................................................................................... 287
E-DOC-CTC-20071119-0014 v1.0
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
eth bridge vlan ifconfig.................................................................................................................... 289
eth bridge xtratag delete..................................................................................................................294
eth bridge xtratag list....................................................................................................................... 296
eth device iflist.................................................................................................................................. 298
eth ifadd............................................................................................................................................. 300
eth ifattach......................................................................................................................................... 301
eth ifconfig.........................................................................................................................................302
eth ifdelete......................................................................................................................................... 303
eth ifdetach........................................................................................................................................ 304
eth switch group list.........................................................................................................................307
eth switch info...................................................................................................................................309
eth switch mirror egress.................................................................................................................. 311
eth switch mirror ingress.................................................................................................................312
eth switch qos ifconfig..................................................................................................................... 314
eth switch qos list.............................................................................................................................315
eth switch shaper config..................................................................................................................317
eth switch shaper ifconfig................................................................................................................318
eth switch storm iflist.......................................................................................................................324
E-DOC-CTC-20071119-0014 v1.0
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
eth vlan add.......................................................................................................................................325
eth vlan delete...................................................................................................................................326
eth vlan flush.....................................................................................................................................327
eth vlan list........................................................................................................................................ 328
expr add............................................................................................................................................. 332
expr delete......................................................................................................................................... 335
expr flush........................................................................................................................................... 336
firewall chain list............................................................................................................................... 345
firewall config.................................................................................................................................... 347
firewall debug clear.......................................................................................................................... 348
firewall level add...............................................................................................................................350
firewall level delete...........................................................................................................................351
firewall level flush.............................................................................................................................352
firewall level list................................................................................................................................ 353
firewall level set................................................................................................................................ 355
firewall rule add................................................................................................................................ 357
firewall rule delete............................................................................................................................ 359
firewall rule flush.............................................................................................................................. 360
E-DOC-CTC-20071119-0014 v1.0
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
grp config...........................................................................................................................................366
grp flush.............................................................................................................................................367
grp rip config.....................................................................................................................................368
grp rip flush.......................................................................................................................................369
grp rip show...................................................................................................................................... 371
hostmgr config.................................................................................................................................. 378
hostmgr list........................................................................................................................................381
ids clear..............................................................................................................................................384
ids parser list.....................................................................................................................................386
ids parser modify.............................................................................................................................. 387
ids signature list................................................................................................................................391
ids signature modify.........................................................................................................................392
igmp host config............................................................................................................................... 398
igmp host flush................................................................................................................................. 401
E-DOC-CTC-20071119-0014 v1.0
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
igmp host ifconfig.............................................................................................................................402
igmp proxy debug clear...................................................................................................................406
igmp proxy debug stats................................................................................................................... 407
igmp proxy flush...............................................................................................................................409
igmp proxy grouplist........................................................................................................................ 410
igmp proxy iflist................................................................................................................................ 412
igmp proxy mbslist...........................................................................................................................413
interface Command................................................................................... 415
ip Commands............................................................................................. 417
ip arpadd............................................................................................................................................419
ip arpdelete........................................................................................................................................420
ip auto ifconfig.................................................................................................................................. 425
ip auto iflist........................................................................................................................................428
ip debug httpprobe........................................................................................................................... 430
ip debug sendto................................................................................................................................ 431
ip debug stats....................................................................................................................................432
ip debug traceconfig.........................................................................................................................433
ip ifconfig........................................................................................................................................... 437
E-DOC-CTC-20071119-0014 v1.0
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
ip ipconfig.......................................................................................................................................... 443
ip mcast flush.................................................................................................................................... 446
ip mcast rtlist.....................................................................................................................................449
ip rtadd...............................................................................................................................................450
ip rtdelete...........................................................................................................................................451
ipqos Commands.......................................................................................453
ipqos config....................................................................................................................................... 454
ipqos ef list........................................................................................................................................ 456
ipqos ef stats..................................................................................................................................... 457
ipqos queue config........................................................................................................................... 460
ipqos queue list.................................................................................................................................461
ipqos queue stats..............................................................................................................................462
label Commands........................................................................................ 463
label chain add.................................................................................................................................. 465
label chain delete.............................................................................................................................. 466
label chain flush................................................................................................................................ 467
label list..............................................................................................................................................471
label modify.......................................................................................................................................472
E-DOC-CTC-20071119-0014 v1.0
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
label rule list......................................................................................................................................476
label rule modify............................................................................................................................... 477
language config.................................................................................................................................480
language delete................................................................................................................................. 481
mbus client authenticate.................................................................................................................. 484
mbus client exec............................................................................................................................... 486
mbus client register.......................................................................................................................... 488
mbus debug loadobjects..................................................................................................................492
mbus listcontexts.............................................................................................................................. 496
mbus listenums................................................................................................................................. 497
mbus listsubscriptions......................................................................................................................499
mbus unregister................................................................................................................................ 502
memm Commands.................................................................................... 503
memm debug lock stats...................................................................................................................505
memm debug lock traceconfig........................................................................................................506
memm debug stats...........................................................................................................................507
memm debug traceconfig................................................................................................................509
memm listobjects..............................................................................................................................510
memm stats....................................................................................................................................... 511
E-DOC-CTC-20071119-0014 v1.0
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
mlp flush............................................................................................................................................ 519
mlp import......................................................................................................................................... 520
mlp privilege add.............................................................................................................................. 521
mlp privilege addzone...................................................................................................................... 522
mlp privilege config..........................................................................................................................523
mlp privilege delete.......................................................................................................................... 524
mlp role add...................................................................................................................................... 527
mlp role config.................................................................................................................................. 529
mlp role delete.................................................................................................................................. 530
mlp role removepriv......................................................................................................................... 532
nat config........................................................................................................................................... 534
nat ifconfig.........................................................................................................................................536
nat mapadd........................................................................................................................................538
nat mapdelete....................................................................................................................................539
nat maplist......................................................................................................................................... 540
nat tmplinst........................................................................................................................................544
nat tmpllist.........................................................................................................................................545
E-DOC-CTC-20071119-0014 v1.0
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
ppp flush............................................................................................................................................ 550
ppp ifadd............................................................................................................................................551
ppp ifattach........................................................................................................................................552
ppp ifconfig........................................................................................................................................553
ppp ifdelete........................................................................................................................................556
ppp ifdetach.......................................................................................................................................557
ppp relay ifadd.................................................................................................................................. 561
ppp relay ifconfig.............................................................................................................................. 562
ppp relay ifdelete.............................................................................................................................. 563
pptp flush...........................................................................................................................................570
pptp ifadd...........................................................................................................................................571
pptp profadd...................................................................................................................................... 573
pptp profdelete.................................................................................................................................. 574
ra Commands.............................................................................................577
ra config............................................................................................................................................. 578
ra start................................................................................................................................................ 579
E-DOC-CTC-20071119-0014 v1.0
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
script run............................................................................................................................................588
service host add................................................................................................................................ 590
service host delete............................................................................................................................ 592
service host disable.......................................................................................................................... 593
service host flush.............................................................................................................................. 594
service host rule add........................................................................................................................ 596
service host rule delete.................................................................................................................... 598
service host triggerlist...................................................................................................................... 601
service system ifadd......................................................................................................................... 602
service system ifdelete..................................................................................................................... 603
service system ipadd........................................................................................................................ 604
service system ipdelete.................................................................................................................... 605
snmp community list........................................................................................................................614
snmp community modify.................................................................................................................615
snmp config....................................................................................................................................... 616
snmp get............................................................................................................................................ 617
snmp getnext.....................................................................................................................................618
snmp ifadd.........................................................................................................................................619
snmp ifattach..................................................................................................................................... 620
snmp ifconfig.....................................................................................................................................621
snmp ifdelete..................................................................................................................................... 622
snmp ifdetach.................................................................................................................................... 623
snmp walk..........................................................................................................................................625
E-DOC-CTC-20071119-0014 v1.0
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
sntp config......................................................................................................................................... 629
software Commands................................................................................. 635
software upgrade.............................................................................................................................. 637
software version................................................................................................................................638
system Commands....................................................................................639
system debug stats...........................................................................................................................642
system dst..........................................................................................................................................643
system locale..................................................................................................................................... 646
system reboot....................................................................................................................................648
system timedreboot.......................................................................................................................... 651
systemlog Commands...............................................................................653
systemlog flush................................................................................................................................. 654
tls Commands............................................................................................ 657
tls acs-client cert list......................................................................................................................... 660
tls acs-client config........................................................................................................................... 661
E-DOC-CTC-20071119-0014 v1.0
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
tls https-server config.......................................................................................................................665
tls self cert list................................................................................................................................... 666
upgrade Commands.................................................................................. 669
upgrade debug traceconfig..............................................................................................................672
upgrade profile add.......................................................................................................................... 673
upnp config........................................................................................................................................680
upnp flush..........................................................................................................................................681
user Commands.........................................................................................683
user config......................................................................................................................................... 685
user rights..........................................................................................................................................689
wireless Commands.................................................................................. 691
wireless debug stats......................................................................................................................... 693
wireless debug txpower................................................................................................................... 694
E-DOC-CTC-20071119-0014 v1.0
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
wireless macacl list...........................................................................................................................700
wireless macacl modify....................................................................................................................701
wireless macacl register...................................................................................................................702
wireless mssid ifadd......................................................................................................................... 703
wireless mssid ifattach..................................................................................................................... 704
wireless mssid ifconfig.....................................................................................................................705
wireless mssid ifdelete..................................................................................................................... 706
wireless mssid ifdetach.................................................................................................................... 707
wireless qos apacconfig................................................................................................................... 714
wireless qos config........................................................................................................................... 715
wireless reset.....................................................................................................................................717
wireless secmode config..................................................................................................................718
wireless wds list................................................................................................................................726
xdsl debug deltconfig....................................................................................................................... 732
xdsl debug deltinfo........................................................................................................................... 733
E-DOC-CTC-20071119-0014 v1.0
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
xdsl debug traceconfig..................................................................................................................... 736
E-DOC-CTC-20071119-0014 v1.0
24
Download from Www.Somanuals.com. All Manuals Search And Download.
.. Command
E-DOC-CTC-20071119-0014 v1.0
26
Download from Www.Somanuals.com. All Manuals Search And Download.
atm Commands
E-DOC-CTC-20071119-0014 v1.0
28
Download from Www.Somanuals.com. All Manuals Search And Download.
atm Commands
E-DOC-CTC-20071119-0014 v1.0
30
Download from Www.Somanuals.com. All Manuals Search And Download.
atm Commands
atm cac config
Configure ATM connection admission control.
SYNTAX:
atm cac config
port = <{dsl0|dsl1|atm2|atm3|aal5|atm5} or
number>
state = <{disabled|enabled}>
where:
port
The port for which CAC is configured.
Enable/disable CAC for an ATM port.
REQUIRED
REQUIRED
state
E-DOC-CTC-20071119-0014 v1.0
31
Download from Www.Somanuals.com. All Manuals Search And Download.
atm Commands
atm cac overbooking
Configure ATM overbooking parameters.
SYNTAX:
atm cac overbooking
[rt = <number{0-1000}]>
[nrt = <number{0-1000}]>
where:
rt
The realtime overbooking percentage.
OPTIONAL
OPTIONAL
nrt
The non-realtime overbooking percentage.
E-DOC-CTC-20071119-0014 v1.0
33
Download from Www.Somanuals.com. All Manuals Search And Download.
atm Commands
atm debug aal5stats
Display AAL5 port specific atm statistics.
SYNTAX:
atm debug aal5stats
port = <{dsl0|dsl1|atm2|atm3|aal5|atm5} or
number>
vpi = <number{0-31}>
[vci = <number{0-511}]>
[clear = <{disabled|enabled}]>
where:
port
vpi
The port number for which statistics will be
retrieved.
REQUIRED
REQUIRED
OPTIONAL
OPTIONAL
The VPI number for which statistics will be
retrieved.
vci
The VCI number for which statistics will be
retrieved.
clear
Clear the statistics after request.
E-DOC-CTC-20071119-0014 v1.0
34
Download from Www.Somanuals.com. All Manuals Search And Download.
atm Commands
atm debug portstats
Display port specific atm statistics.
SYNTAX:
atm debug portstats
port = <{dsl0|dsl1|atm2|atm3|aal5|atm5} or
number>
[clear = <{disabled|enabled}]>
where:
port
The port for which statistics will be retrieved.
Clear the statistics after the request.
REQUIRED
OPTIONAL
clear
E-DOC-CTC-20071119-0014 v1.0
36
Download from Www.Somanuals.com. All Manuals Search And Download.
atm Commands
atm ifadd
Create a new ATM interface.
SYNTAX:
atm ifadd
where:
intf = <string>
intf
The name for the new ATM interface. If not
specified, the destination will double as interface
name.
REQUIRED
E-DOC-CTC-20071119-0014 v1.0
38
Download from Www.Somanuals.com. All Manuals Search And Download.
atm Commands
atm ifconfig
Modify an ATM interface.
SYNTAX:
atm ifconfig
intf = <{atm_Internet}>
[dest = <{}]>
[qos = <{default}]>
[clp = <{0|1|classification}]>
[clpthresh = <number{0-15}]>
[encaps = <{llc|vcmux}]>
[fcs = <{disabled|enabled|auto}]>
[ulp = <{mac|ip|ppp}]>
[retry = <number{0-65535}]>
where:
intf
The name of the ATM interface to configure.
REQUIRED
OPTIONAL
dest
The WAN destination for this ATM interface.
Typically, a phonebook entry.
qos
The name of a qosbook entry defining the QoS
parameters for the WAN link.
OPTIONAL
clp
The mode used to determine the CLP bit value.
OPTIONAL
OPTIONAL
clpthresh
Priority class threshold where CLP becomes 0
(for all classes >= threshold).
encaps
fcs
The WAN protocol encapsulation to be used on
this interface.
OPTIONAL
OPTIONAL
Whether or not to include the Ethernet
FCS in the packet header (only used for llc
encapsulation for mac).
ulp
The upper layer protocol.
OPTIONAL
OPTIONAL
retry
The number of times the WAN connection setup
should retry before giving up.
E-DOC-CTC-20071119-0014 v1.0
40
Download from Www.Somanuals.com. All Manuals Search And Download.
atm Commands
atm oam cc modify
Modify CC on the connection.
SYNTAX:
atm oam cc modify
port = <{dsl0|dsl1|atm2|atm3|aal5|atm5} or
number>
vpi = <number{0-31}>
[vci = <number{0-511}]>
[transmit = <{disabled|enabled}]>
[receive = <{disabled|enabled}]>
[auto = <{disabled|enabled}]>
[span = <{segment|end2end}]>
where:
port
The ATM port number.
REQUIRED
vpi
The Virtual Path Identifier.
REQUIRED
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
vci
The Virtual Channel Identifier.
Enable/disable transmission of CC cells.
Enable/disable loss of continuity.
transmit
receive
auto
Enable/disable remote CC activation/
deactivation.
span
End2end or segment continuity check.
OPTIONAL
E-DOC-CTC-20071119-0014 v1.0
45
Download from Www.Somanuals.com. All Manuals Search And Download.
atm Commands
atm oam cc send
Send CC activate/deactivate to connection.
SYNTAX:
atm oam cc send
port = <{dsl0|dsl1|atm2|atm3|aal5|atm5} or
number>
vpi = <number{0-31}>
[vci = <number{0-511}]>
[span = <{segment|end2end}]>
[action = <{activate|deactivate}]>
[direction = <{source|sink|both}]>
where:
port
The ATM port number.
REQUIRED
REQUIRED
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
vpi
The Virtual Path Identifier.
The Virtual Channel Identifier.
Send CC action end2end or segment.
The CC action.
vci
span
action
direction
Source, sink or both (default: both).
E-DOC-CTC-20071119-0014 v1.0
46
Download from Www.Somanuals.com. All Manuals Search And Download.
atm Commands
atm oam config
Modify the ATM OAM settings.
SYNTAX:
atm oam config
[clp = <number{0-1}]>
[loopbackid = <string]>
where:
clp
The CLP bit value of the OAM cells.
OPTIONAL
OPTIONAL
loopbackid
The loopback id (hexadecimal string) for
processing of segment loopback cells.
E-DOC-CTC-20071119-0014 v1.0
47
Download from Www.Somanuals.com. All Manuals Search And Download.
atm Commands
atm oam modify
Modify the ATM OAM data blocking mode.
SYNTAX:
atm oam modify
port = <{dsl0|dsl1|atm2|atm3|aal5|atm5} or
number>
blocking = <{disabled|enabled}>
where:
port
The port for which OAM blocking is configured.
Enable/disable OAM blocking.
REQUIRED
REQUIRED
blocking
E-DOC-CTC-20071119-0014 v1.0
49
Download from Www.Somanuals.com. All Manuals Search And Download.
atm Commands
atm oam ping
Send ATM loopback cells.
SYNTAX:
atm oam ping
dest = <{atm_pvc_8_35}>
[count = <number{1-1000000}]>
[interval = <number{100-1000000}]>
where:
dest
The destination address for the request.
The number of pings to send.
REQUIRED
OPTIONAL
OPTIONAL
count
interval
The interval in milliseconds between packets.
E-DOC-CTC-20071119-0014 v1.0
50
Download from Www.Somanuals.com. All Manuals Search And Download.
atm Commands
atm oam vclb add
Create a loopback connection for VC
SYNTAX:
atm oam vclb add
port = <{dsl0|dsl1|atm2|atm3|aal5|atm5} or
number>
vpi = <number{0-31}>
[vci = <number{0-511}]>
where:
port
vpi
vci
The ATM port number.
REQUIRED
The Virtual Path Identifier.
The Virtual Channel Identifier.
REQUIRED
OPTIONAL
E-DOC-CTC-20071119-0014 v1.0
51
Download from Www.Somanuals.com. All Manuals Search And Download.
atm Commands
atm oam vclb del
Delete a loopback connection for VC
SYNTAX:
atm oam vclb del
port = <{dsl0|dsl1|atm2|atm3|aal5|atm5} or
number>
vpi = <number{0-31}>
[vci = <number{0-511}]>
where:
port
vpi
vci
The ATM port number.
REQUIRED
REQUIRED
OPTIONAL
The Virtual Path Identifier.
The Virtual Channel Identifier.
E-DOC-CTC-20071119-0014 v1.0
52
Download from Www.Somanuals.com. All Manuals Search And Download.
atm Commands
atm phonebook add
Add a new phonebook entry.
SYNTAX:
atm phonebook add
name = <string>
addr = <atmchannel : PVC syntax is
[port.]vpi.vci port=dsl0|dsl1|...>
where:
name
addr
The phonebook name for this destination.
The address for this destination.
REQUIRED
REQUIRED
E-DOC-CTC-20071119-0014 v1.0
54
Download from Www.Somanuals.com. All Manuals Search And Download.
atm Commands
atm qosbook add
Add a new qosbook entry.
SYNTAX:
atm qosbook add
name = <string>
[txctd = <{default}]>
[rxctd = <{default}]>
where:
name
txctd
The name for the new QoS entry.
REQUIRED
OPTIONAL
The name of the CTD for transmit (upstream)
direction.
rxctd
The name of the CTD for receive (downstream)
direction.
OPTIONAL
E-DOC-CTC-20071119-0014 v1.0
59
Download from Www.Somanuals.com. All Manuals Search And Download.
atm Commands
atm qosbook ctdadd
Add a new connection traffic descriptor.
SYNTAX:
atm qosbook ctdadd
name = <string>
conformance = <{UBR|CBR|VBR|UBR.1|UBR.2|
UBR.mdcr|CBR.1|VBR.1|VBR.2|VBR.3|VBR.c|VBR.nt|
VBR.t|GFR.1|GFR.2}>
[peakrate = <number{0-27786}]>
[sustrate = <number{0-27786}]>
[maxburst = <number{48-12240}]>
[minrate = <number{0-27786}]>
[maxframe = <number{0-255}]>
[celldelay = <number]>
[realtime = <{enabled|disabled}]>
[framediscard = <{enabled|disabled}]>
where:
name
The name for the new CTD entry.
REQUIRED
REQUIRED
OPTIONAL
conformance
peakrate
The ATM service conformance definition.
The peak rate (in kilobits per second). Use '0' to
indicate linerate for UBR.
sustrate
The sustainable rate (in kilobits per second).
(VBR only)
OPTIONAL
maxburst
minrate
The maximum burst size (in bytes). (VBR or GFR) OPTIONAL
The minimum rate (in kilobits per second).
(UBR.m or GFR)
OPTIONAL
maxframe
celldelay
The maximum frame size (in bytes). (GFR only)
Cell delay variation in tenths of microseconds.
Enable/disable realtime traffic (VBR only).
Enable/disable frame discard.
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
realtime
framediscard
E-DOC-CTC-20071119-0014 v1.0
61
Download from Www.Somanuals.com. All Manuals Search And Download.
atm Commands
atm qosbook ctddelete
Delete a connection traffic descriptor.
SYNTAX:
atm qosbook ctddelete
name = <{default}>
[force = <{disabled|enabled}]>
where:
name
force
The name of the CTD entry to delete.
REQUIRED
OPTIONAL
Force delete even when the entry is still in use.
E-DOC-CTC-20071119-0014 v1.0
62
Download from Www.Somanuals.com. All Manuals Search And Download.
atm Commands
atm qosbook delete
Delete a qosbook entry.
SYNTAX:
atm qosbook delete
name = <{default}>
[force = <{disabled|enabled}]>
where:
name
force
The name of the qosbook entry to delete.
REQUIRED
OPTIONAL
Force delete even when the entry is still in use.
E-DOC-CTC-20071119-0014 v1.0
64
Download from Www.Somanuals.com. All Manuals Search And Download.
autopvc Commands
autopvc config
Configure autopvc.
SYNTAX:
autopvc config
[mode = <{pseudo|passive|active}]>
[type = <{bridge|pppoerelay|ipoa|ethoa|pppoa|
pppoe}]>
[overwrite = <{disabled|enabled}]>
[peakrate = <number{0-27786}]>
where:
mode
Autopvc mode.
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
type
Type of autopvc.
overwrite
peakrate
Enable/disable UBR peak rate overwrite.
The UBR peak rate (in kilobits per second) '0' to
indicate linerate.
E-DOC-CTC-20071119-0014 v1.0
68
Download from Www.Somanuals.com. All Manuals Search And Download.
autopvc Commands
autopvc list
Show retreived information.
SYNTAX:
autopvc list
[table = <{Port|AtmLayer|Vpc|Vcc|Address|
AddressRegistrationAdmin|AAL5Profile|
AAL2CommonProfile|AAL2TrunkingProfile|
AAL2LESProfile|AtmServiceConnInfoExtension|
AtmServiceTypeExtension|
AAL5ProfileExtension}]>
where:
table
Autopvc table.
OPTIONAL
E-DOC-CTC-20071119-0014 v1.0
69
Download from Www.Somanuals.com. All Manuals Search And Download.
config Commands
E-DOC-CTC-20071119-0014 v1.0
70
Download from Www.Somanuals.com. All Manuals Search And Download.
config Commands
config load
Load saved or default configuration.
SYNTAX:
config load
[load_ip = <{enabled|disabled}]>
[defaults = <{disabled|enabled}]>
[flush = <{enabled|disabled}]>
[echo = <{disabled|enabled}]>
[filename = <string]>
where:
load_ip
defaults
flush
Load IP settings or not.
OPTIONAL
OPTIONAL
OPTIONAL
Load default instead of saved configuration.
Flush current configuration before loading new
one.
echo
Echo each command string when loaded.
Configuration filename.
OPTIONAL
OPTIONAL
filename
E-DOC-CTC-20071119-0014 v1.0
76
Download from Www.Somanuals.com. All Manuals Search And Download.
config Commands
config save
Store current configuration to backup file
SYNTAX:
config save
where:
filename = <user configuration filename>
filename
Filename for backupfile of current configuration
REQUIRED
E-DOC-CTC-20071119-0014 v1.0
77
Download from Www.Somanuals.com. All Manuals Search And Download.
connection Commands
E-DOC-CTC-20071119-0014 v1.0
78
Download from Www.Somanuals.com. All Manuals Search And Download.
connection Commands
connection appconfig
Modify a CONN/NAT application helper configuration
SYNTAX:
connection appconfig
application = <{IP6TO4|PPTP|ESP|IKE|SIP|
JABBER|CU/SeeMe|RAUDIO(PNA)|RTSP|ILS|H245|
H323|IRC|GAME(UDP)|CONE(UDP)|LOOSE(UDP)|FTP}>
[trace = <{disabled|enabled}]>
[timeout = <number{0-32000}]>
[childqos = <{DSCP|Interactive|Management|
Video|VoIP-RTP|VoIP-Signal|default}]>
[floating = <{disabled|enabled}]>
[proxy = <{disabled|enabled}]>
[tracelevel = <number{1-4}]>
[SIP_ALG = <{disabled|enabled}]>
[RTP_predict_for_term_SIP_ALG = <{disabled|
enabled}]>
where:
application
The name of a CONN/NAT application helper as
listed by ':connection applist'.
REQUIRED
OPTIONAL
OPTIONAL
OPTIONAL
trace
Enable/disable CONN/NAT application helper
traces.
timeout
childqos
The maximum timeout in seconds to keep
predicted child connections around.
Used QOS label for the predicted child
connections.
floating
proxy
Enable/disabled floating port for IKE helper.
Enable/disable FTP proxy support.
OPTIONAL
OPTIONAL
OPTIONAL
tracelevel
SIP trace level: 1=feature errors; 2=feature
traces; 3=all errors; 4=all traces.
SIP_ALG
SIP only: enable/disable traditional sip alg
behaviour
OPTIONAL
OPTIONAL
RTP_predict_for_term_SIP_ALG
SIP only: enable/disable RTP connection
prediction for terminated SIP
E-DOC-CTC-20071119-0014 v1.0
80
Download from Www.Somanuals.com. All Manuals Search And Download.
connection Commands
connection appinfo
Display CONN/NAT application specific info
SYNTAX:
connection appinfo
application = <{IP6TO4|PPTP|ESP|IKE|SIP|
JABBER|CU/SeeMe|RAUDIO(PNA)|RTSP|ILS|H245|
H323|IRC|GAME(UDP)|CONE(UDP)|LOOSE(UDP)|FTP}>
where:
application
The name of a CONN/NAT application helper as
listed by ':connection applist'.
REQUIRED
E-DOC-CTC-20071119-0014 v1.0
81
Download from Www.Somanuals.com. All Manuals Search And Download.
connection Commands
connection bind
Create a CONN/NAT application helper/port binding.
SYNTAX:
connection bind
application = <{IP6TO4|PPTP|ESP|IKE|SIP|
JABBER|CU/SeeMe|RAUDIO(PNA)|RTSP|ILS|H245|
H323|IRC|GAME(UDP)|CONE(UDP)|LOOSE(UDP)|FTP}>
port = <port-range>
where:
application
The name of a CONN/NAT application helper as
listed by ':connection applist'.
REQUIRED
REQUIRED
port
The port number or range this application
handler should work on.
E-DOC-CTC-20071119-0014 v1.0
83
Download from Www.Somanuals.com. All Manuals Search And Download.
connection Commands
connection config
Modify global connection configuration.
SYNTAX:
connection config
[configchangemode = <{immediate|delayed}]>
[probes = <{disabled|enabled}]>
[udptrackmode = <{strict|loose}]>
where:
configchangemode
probes
Select how config changes are handled.
Enable/disable alive probes on idle connections.
UDP connection tracking mode.
OPTIONAL
OPTIONAL
OPTIONAL
udptrackmode
E-DOC-CTC-20071119-0014 v1.0
87
Download from Www.Somanuals.com. All Manuals Search And Download.
connection Commands
connection list
Display the currently known connections.
SYNTAX:
connection list
[nr = <number{1-2048}]>
[history = <{disabled|enabled}]>
where:
nr
The number of connections to display.
If enabled, show history.
OPTIONAL
OPTIONAL
history
E-DOC-CTC-20071119-0014 v1.0
92
Download from Www.Somanuals.com. All Manuals Search And Download.
connection Commands
connection timerclear
Clear connection timeout to default.
SYNTAX:
connection timerclear
[timer = <{tcpidle|tcpneg|tcpkill|udpidle|
udpkill|icmpkill|ipidle|ipkill|aiprefresh}]>
where:
timer
The name of the connection idle timer.
OPTIONAL
E-DOC-CTC-20071119-0014 v1.0
95
Download from Www.Somanuals.com. All Manuals Search And Download.
connection Commands
connection timerconfig
Modify connection timeout handling.
SYNTAX:
connection timerconfig
[timer = <{tcpidle|tcpneg|tcpkill|udpidle|
udpkill|icmpkill|ipidle|ipkill|aiprefresh}]>
[value = <number{0-86400}]>
where:
timer
value
The name of the connection idle timer.
The timer expire value in seconds.
OPTIONAL
OPTIONAL
E-DOC-CTC-20071119-0014 v1.0
96
Download from Www.Somanuals.com. All Manuals Search And Download.
connection Commands
connection unbind
Delete a CONN/NAT application helper/port binding.
SYNTAX:
connection unbind
application = <{IP6TO4|PPTP|ESP|IKE|SIP|
JABBER|CU/SeeMe|RAUDIO(PNA)|RTSP|ILS|H245|
H323|IRC|GAME(UDP)|CONE(UDP)|LOOSE(UDP)|FTP}>
port = <port-range>
where:
application
The name of a CONN/NAT application helper as
listed by ':connection applist'.
REQUIRED
REQUIRED
port
The port number or range this application
handler should work on.
E-DOC-CTC-20071119-0014 v1.0
97
Download from Www.Somanuals.com. All Manuals Search And Download.
cwmp Commands
E-DOC-CTC-20071119-0014 v1.0
98
Download from Www.Somanuals.com. All Manuals Search And Download.
cwmp Commands
cwmp config
Configure the cwmpd as seen from the ACS.
SYNTAX:
cwmp config
[state = <{disabled|enabled}]>
[mode = <{read-only|full}]>
[periodicInform = <{disabled|enabled}]>
[periodicInfInt = <number]>
[sessionTimeout = <number]>
[noIpTimeout = <number]>
[maxEnvelopes = <number]>
[connectionRequest = <{disabled|enabled}]>
[connectionReqPath = <string]>
[connectionReqUserName = <quoted string]>
[connectionReqPsswd = <password]>
[connectionReqAuth = <{none|basic|digest}]>
[qos-class = <number]>
[bootdelayrange = <number]>
[upgradedelay = <{disabled|enabled}]>
[am1Termination = <{disabled|enabled}]>
[persistentSubscription = <{disabled|
enabled}]>
where:
state
The state of the cwmp daemon.
OPTIONAL
mode
Set the operation mode of the cwmp daemon.
Set periodicInform flag of the cwmp daemon.
OPTIONAL
OPTIONAL
OPTIONAL
periodicInform
periodicInfInt
Set the interval between two periodicInform
messages in seconds.
sessionTimeout
noIpTimeout
Set HTTP session-timeout in seconds.
OPTIONAL
OPTIONAL
Set time (in seconds) ip may be 0 after
uploading new config file.
maxEnvelopes
Set the maximum number of SOAP envelopes
send within one http-message.
OPTIONAL
OPTIONAL
OPTIONAL
connectionRequest
connectionReqPath
Set connection request flag of the cwmp
daemon.
Set the path where the cwmp daemon can be
reached.
connectionReqUserName
connectionReqPsswd
Set the username the ACS must use to log in.
Set the password the ACS must use to log in.
OPTIONAL
OPTIONAL
E-DOC-CTC-20071119-0014 v1.0
100
Download from Www.Somanuals.com. All Manuals Search And Download.
cwmp Commands
connectionReqAuth
qos-class
Set the authentication type of modem CWMP
server for asynchronous connects.
OPTIONAL
OPTIONAL
Set the quality of service class for outgoing
CWMP data.
bootdelayrange
upgradedelay
Set the delay on boot before inform is sent.
OPTIONAL
OPTIONAL
Set whether to delay upgrade if services are
active.
am1Termination
Set if am 1 session termination is enabled.
OPTIONAL
persistentSubscription
The cwmp daemon has persistent subscriptions. OPTIONAL
E-DOC-CTC-20071119-0014 v1.0
101
Download from Www.Somanuals.com. All Manuals Search And Download.
cwmp Commands
cwmp server config
Configure the cwmpd towards the ACS.
SYNTAX:
cwmp server config
[url = <string]>
[username = <string]>
[password = <password]>
where:
url
Set the HTTP URL used to contact the ACS
server.
OPTIONAL
username
password
Set the username for ACS Digest Authentication. OPTIONAL
Set the password for ACS Digest Authentication. OPTIONAL
E-DOC-CTC-20071119-0014 v1.0
103
Download from Www.Somanuals.com. All Manuals Search And Download.
debug Command
E-DOC-CTC-20071119-0014 v1.0
104
Download from Www.Somanuals.com. All Manuals Search And Download.
dhcp Commands
E-DOC-CTC-20071119-0014 v1.0
106
Download from Www.Somanuals.com. All Manuals Search And Download.
dhcp Commands
E-DOC-CTC-20071119-0014 v1.0
108
Download from Www.Somanuals.com. All Manuals Search And Download.
dhcp Commands
E-DOC-CTC-20071119-0014 v1.0
109
Download from Www.Somanuals.com. All Manuals Search And Download.
dhcp Commands
E-DOC-CTC-20071119-0014 v1.0
110
Download from Www.Somanuals.com. All Manuals Search And Download.
dhcp Commands
dhcp client ifconfig
Configure a DHCP client.
SYNTAX:
dhcp client ifconfig
intf = <>
[label = <{None|DSCP|Interactive|Management|
Video|VoIP-RTP|VoIP-Signal|default}]>
[metric = <number{0-255}]>
[dnsmetric = <number{0-100}]>
[broadcast = <{disabled|enabled}]>
[serverroute = <{disabled|enabled}]>
[followlabel = <{disabled|enabled}]>
where:
intf
The name of the dynamic interface to be
configured.
REQUIRED
label
Label for default gateway and static routes.
OPTIONAL
OPTIONAL
metric
Route metric for default gateway and static
routes.
dnsmetric
broadcast
serverroute
followlabel
DNS route metric.
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
Operate client in unicast/broadcast mode.
Insert a route for the DHCP server IP
If enabled the DHCP client's unicast traffic will
follow the route label specified. If disabled DHCP
unicast traffic will follow standard routes
E-DOC-CTC-20071119-0014 v1.0
117
Download from Www.Somanuals.com. All Manuals Search And Download.
dhcp Commands
dhcp client ifdetach
De-activate a DHCP client and releases its lease.
SYNTAX:
dhcp client ifdetach
intf = <>
where:
intf
The name of the interface on which a DHCP
Client is defined.
REQUIRED
E-DOC-CTC-20071119-0014 v1.0
119
Download from Www.Somanuals.com. All Manuals Search And Download.
dhcp Commands
dhcp client iflist
List DHCP clients.
SYNTAX:
dhcp client iflist
[intf = <]>
[expand = <{disabled|enabled}]>
where:
intf
The name of the interface on which a DHCP
Client is defined.
OPTIONAL
OPTIONAL
expand
Expand enabled/disabled.
E-DOC-CTC-20071119-0014 v1.0
120
Download from Www.Somanuals.com. All Manuals Search And Download.
dhcp Commands
dhcp client rqoptions add
Add a DHCP Option Code to the Parameter Request List.
SYNTAX:
dhcp client rqoptions add
intf = <>
option = <{subnet-mask|time-offset|default-
routers|time-servers|ien116-name-impress-
servers|resource-location-servers|host-
name|boot-file-size|merit-dump|domain-name|
swap-server|root-path|extensions-path|ip-
forwarding|non-local-source-routing|policy-
filter|max-dgram-reassembly|default-ip-ttl|
path-mtu-aging-timeout|path-mtu-plateau-table|
interface-mtu|all-subnets-local|broadcast-
address|perform-mask-discovery|...} or number>
[index = <number{0-255}]>
where:
intf
The name of the interface on which a DHCP
Client is defined.
REQUIRED
option
index
The name or number of the option.
The index of the option.
REQUIRED
OPTIONAL
E-DOC-CTC-20071119-0014 v1.0
122
Download from Www.Somanuals.com. All Manuals Search And Download.
dhcp Commands
dhcp client rqoptions delete
Delete a DHCP Option Code from the Parameter Request List.
SYNTAX:
dhcp client rqoptions delete
intf = <>
option = <{subnet-mask|time-offset|default-
routers|time-servers|ien116-name-impress-
servers|resource-location-servers|host-
name|boot-file-size|merit-dump|domain-name|
swap-server|root-path|extensions-path|ip-
forwarding|non-local-source-routing|policy-
filter|max-dgram-reassembly|default-ip-ttl|
path-mtu-aging-timeout|path-mtu-plateau-table|
interface-mtu|all-subnets-local|broadcast-
address|perform-mask-discovery|...} or number>
where:
intf
The name of the interface on which a DHCP
Client is defined.
REQUIRED
REQUIRED
option
The name or number of the option.
E-DOC-CTC-20071119-0014 v1.0
123
Download from Www.Somanuals.com. All Manuals Search And Download.
dhcp Commands
dhcp client rqoptions list
List all DHCP Option Codes in the Parameter Request List.
SYNTAX:
dhcp client rqoptions list
[intf = <]>
where:
intf
The name of the interface on which a DHCP
Client is defined.
OPTIONAL
E-DOC-CTC-20071119-0014 v1.0
124
Download from Www.Somanuals.com. All Manuals Search And Download.
dhcp Commands
dhcp client txoptions add
Add an option.
SYNTAX:
dhcp client txoptions add
intf = <>
option = <{subnet-mask|time-offset|default-
routers|time-servers|ien116-name-impress-
servers|resource-location-servers|host-
name|boot-file-size|merit-dump|domain-name|
swap-server|root-path|extensions-path|ip-
forwarding|non-local-source-routing|policy-
filter|max-dgram-reassembly|default-ip-ttl|
path-mtu-aging-timeout|path-mtu-plateau-table|
interface-mtu|all-subnets-local|broadcast-
address|perform-mask-discovery|...} or number>
[enterprise = <number{1-2147483647}]>
[suboption = <number{1-254}]>
value = <Value : (type)value; type being 8-
bit, 16-bit, 32-bit, addr, >
[index = <number{0-255}]>
where:
intf
The name of the interface on which a DHCP
Client is defined.
REQUIRED
REQUIRED
option
The name or number of the option.
enterprise
The enterprise number (see http://www.iana.org/ OPTIONAL
assignments/enterprise- numbers)
suboption
value
The suboption number
The value of the option.
OPTIONAL
REQUIRED
OPTIONAL
index
The index of the (sub)option/enterprise number
in the Option List.
E-DOC-CTC-20071119-0014 v1.0
126
Download from Www.Somanuals.com. All Manuals Search And Download.
dhcp Commands
dhcp client txoptions delete
Delete an option.
SYNTAX:
dhcp client txoptions delete
intf = <>
option = <{subnet-mask|time-offset|default-
routers|time-servers|ien116-name-impress-
servers|resource-location-servers|host-
name|boot-file-size|merit-dump|domain-name|
swap-server|root-path|extensions-path|ip-
forwarding|non-local-source-routing|policy-
filter|max-dgram-reassembly|default-ip-ttl|
path-mtu-aging-timeout|path-mtu-plateau-table|
interface-mtu|all-subnets-local|broadcast-
address|perform-mask-discovery|...} or number>
[enterprise = <number{1--1}]>
[suboption = <number{1-254}]>
where:
intf
The name of the interface on which a DHCP
Client is defined.
REQUIRED
REQUIRED
option
The name or number of the option.
enterprise
The enterprise number (see http://www.iana.org/ OPTIONAL
assignments/enterprise- numbers)
suboption
The suboption number
OPTIONAL
E-DOC-CTC-20071119-0014 v1.0
127
Download from Www.Somanuals.com. All Manuals Search And Download.
dhcp Commands
dhcp client txoptions list
List all options.
SYNTAX:
dhcp client txoptions list
[intf = <]>
[expand = <{disabled|enabled}]>
where:
intf
The name of the interface on which a DHCP
Client is defined.
OPTIONAL
OPTIONAL
expand
Expand enabled/disabled.
E-DOC-CTC-20071119-0014 v1.0
128
Download from Www.Somanuals.com. All Manuals Search And Download.
dhcp Commands
dhcp relay config
Sets the relay configuration settings.
SYNTAX:
dhcp relay config
[agentinfo = <{disabled|enabled}]>
[agentmismatch = <{disabled|enabled}]>
where:
agentinfo
Set the relay agent info status (RFC3046).
OPTIONAL
OPTIONAL
agentmismatch
Forward/Drop DHCP reply packet when a relay
agent info mismatch is detected (RFC3046).
E-DOC-CTC-20071119-0014 v1.0
131
Download from Www.Somanuals.com. All Manuals Search And Download.
dhcp Commands
dhcp relay ifconfig
Configure a relay interface.
SYNTAX:
dhcp relay ifconfig
intf = <{LocalNetwork|Internet}>
[relay = <{disabled|enabled}]>
[maxhops = <number{0-16}]>
[remoteid = <password]>
[trusted = <{disabled|enabled}]>
where:
intf
The name of the relay interface to configure.
Set the relay status.
REQUIRED
OPTIONAL
OPTIONAL
relay
maxhops
Set the maximum number of hops allowed in
the DHCP packet.
remoteid
trusted
Set the remote id as specified in RFC3046.
OPTIONAL
Drop/Forward DHCP request packet when a relay OPTIONAL
agent info option is present and the giaddr field
is 0 (RFC3046).
E-DOC-CTC-20071119-0014 v1.0
136
Download from Www.Somanuals.com. All Manuals Search And Download.
dhcp Commands
dhcp relay modify
Modify an entry from the DHCP forward list.
SYNTAX:
dhcp relay modify
name = <{LocalNetwork_to_127.0.0.1}>
[addr = <ip-address]>
[intf = <{None|LocalNetwork|Internet}]>
[giaddr = <ip-address]>
[script = <]>
where:
name
addr
intf
The forward entry name.
REQUIRED
OPTIONAL
OPTIONAL
The DHCP server IP address.
The name of the relay interface, 'None' to
indicate no interface is specified.
giaddr
script
The giaddr field to be used in relayed DHCP
packets.
OPTIONAL
OPTIONAL
Script to be run when the forward entry is hit.
E-DOC-CTC-20071119-0014 v1.0
139
Download from Www.Somanuals.com. All Manuals Search And Download.
dhcp Commands
dhcp relay ruleadd
Add a selection rule to a DHCP forward entry
SYNTAX:
dhcp relay ruleadd
name = <{LocalNetwork_to_127.0.0.1}>
[key = <{or|and}]>
rulename = <>
where:
name
key
The name of the forward entry.
REQUIRED
OPTIONAL
REQUIRED
The logical key of the selection rule.
The name of the DHCP selection rule.
rulename
E-DOC-CTC-20071119-0014 v1.0
140
Download from Www.Somanuals.com. All Manuals Search And Download.
dhcp Commands
dhcp relay ruledelete
Delete a selection rule from a DHCP forward entry
SYNTAX:
dhcp relay ruledelete
name = <{LocalNetwork_to_127.0.0.1}>
rulename = <>
where:
name
The name of the forward entry.
REQUIRED
REQUIRED
rulename
The name of the DHCP selection rule.
E-DOC-CTC-20071119-0014 v1.0
141
Download from Www.Somanuals.com. All Manuals Search And Download.
dhcp Commands
dhcp rule add
Add a rule for DHCP conditional selection
SYNTAX:
dhcp rule add
name = <string>
type = <{option|mac|vci|uci}>
option [!] = <{subnet-mask|time-offset|
default-routers|time-servers|ien116-servers|
impress-servers|resource-location-servers|
host-name|boot-file-size|merit-dump|domain-
name|swap-server|root-path|extensions-path|
ip-forwarding|non-local-source-routing|policy-
filter|max-dgram-reassembly|default-ip-ttl|
path-mtu-aging-timeout|path-mtu-plateau-table|
interface-mtu|all-subnets-local|broadcast-
address|perform-mask-discovery|...} or number>
[enterprise = <number{1-2147483647}]>
[suboption = <number{1-254}]>
[value = <Value : (type)value; type being
addr, ascii, byte_array, ]>
[match = <{exactly|as_substring}]>
mac [!] = <hardware-address with wildcard ex:
'00:9f:aa:*:*:*'>
where:
name
The name of the DHCP rule.
REQUIRED
REQUIRED
REQUIRED
type
Specify the DHCP rule type.
option [!]
The name or number of the option.
If a value is preceded by a
enterprise
The enterprise number (see http://www.iana.org/ OPTIONAL
assignments/enterprise- numbers)
suboption
value
The suboption number
The value of the option.
The option value matching.
OPTIONAL
OPTIONAL
OPTIONAL
REQUIRED
match
mac [!]
The mac address.
If a value is preceded by a
E-DOC-CTC-20071119-0014 v1.0
142
Download from Www.Somanuals.com. All Manuals Search And Download.
dhcp Commands
dhcp server lease add
Add a DHCP server lease
SYNTAX:
dhcp server lease add
clientid = <clientid>
pool = <{LAN_private}>
[addr = <ip-address]>
[offset = <number]>
[leasetime = <number]>
[expirytime = <number]>
[gateway = <ip-address|0|none]>
[macaddr = <hardware-address]>
where:
clientid
pool
The DHCP client identification string of the host.
The name of the DHCP server pool.
The IP address for this client.
REQUIRED
REQUIRED
OPTIONAL
OPTIONAL
addr
offset
The IP address offset in the pool preserved for
this client.
leasetime
expirytime
gateway
The time in seconds the client is allowed to use
an address (tip: 0 means infinite leasetime).
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
The time in seconds the DHCP server keeps the
lease reserved (tip: 0 means infinite expirytime).
The IP address of the default router for this
client.
macaddr
The host MAC address.
E-DOC-CTC-20071119-0014 v1.0
152
Download from Www.Somanuals.com. All Manuals Search And Download.
dhcp Commands
dhcp server lease delete
Delete a DHCP server lease
SYNTAX:
dhcp server lease delete
[clientid = <clientid]>
[index = <number]>
[expand = <{disabled|enabled}]>
where:
clientid
index
The DHCP client identification string.
The DHCP server lease table index.
Expand enabled/disabled.
OPTIONAL
OPTIONAL
OPTIONAL
expand
E-DOC-CTC-20071119-0014 v1.0
153
Download from Www.Somanuals.com. All Manuals Search And Download.
dhcp Commands
dhcp server lease flush
Flush all DHCP server leases
SYNTAX:
dhcp server lease flush
[pool = <{LAN_private}]>
where:
pool
The name of the DHCP server pool. Only the
leases belonging to this pool will be deleted.
OPTIONAL
E-DOC-CTC-20071119-0014 v1.0
154
Download from Www.Somanuals.com. All Manuals Search And Download.
dhcp Commands
dhcp server lease list
List all DHCP server leases
SYNTAX:
dhcp server lease list
[clientid = <clientid]>
[index = <number]>
[expand = <{disabled|enabled}]>
where:
clientid
index
The DHCP client identification string.
The DHCP server lease table index.
Expand enabled/disabled.
OPTIONAL
OPTIONAL
OPTIONAL
expand
E-DOC-CTC-20071119-0014 v1.0
155
Download from Www.Somanuals.com. All Manuals Search And Download.
dhcp Commands
dhcp server option instadd
Add a DHCP server option instance
SYNTAX:
dhcp server option instadd
name = <string>
tmplname = <>
[policy = <{requested|always|rules}]>
[dynamic = <{disabled|enabled}]>
[maxuse = <number{1-255}]>
[enterprise = <number{1-2147483647}]>
[suboption = <number{1-254}]>
value = <Value : (type)value; type being 8-
bit, 16-bit, 32-bit, addr, >
where:
name
The name of the DHCP server option instance.
The name of the DHCP server option template.
REQUIRED
tmplname
policy
REQUIRED
OPTIONAL
The transmit policy type for the DHCP server
option instance.
dynamic
maxuse
Enable/Disable option instance as dynamic.
OPTIONAL
OPTIONAL
Maximum number of times an option instance
can be used in DHCP pools
enterprise
The enterprise number (see http://www.iana.org/ OPTIONAL
assignments/enterprise- numbers)
suboption
value
The suboption number
OPTIONAL
REQUIRED
The value of the DHCP server option instance.
E-DOC-CTC-20071119-0014 v1.0
157
Download from Www.Somanuals.com. All Manuals Search And Download.
dhcp Commands
dhcp server option instdelete
Delete a DHCP server option instance
SYNTAX:
dhcp server option instdelete name = <>
[enterprise = <number{1--1}]>
[suboption = <number{1-254}]>
where:
name
The name of the DHCP server option instance.
REQUIRED
enterprise
The enterprise number (see http://www.iana.org/ OPTIONAL
assignments/enterprise- numbers)
suboption
The suboption number
OPTIONAL
E-DOC-CTC-20071119-0014 v1.0
158
Download from Www.Somanuals.com. All Manuals Search And Download.
dhcp Commands
dhcp server option ruleadd
Add a selection rule to a DHCP server option instance
SYNTAX:
dhcp server option ruleadd
name = <>
[key = <{or|and}]>
rulename = <>
where:
name
key
The name of the DHCP server option instance.
The logical key of the selection rule.
REQUIRED
OPTIONAL
REQUIRED
rulename
The name of the DHCP selection rule.
E-DOC-CTC-20071119-0014 v1.0
160
Download from Www.Somanuals.com. All Manuals Search And Download.
dhcp Commands
dhcp server option ruledelete
Delete a selection rule from a DHCP server option instance
SYNTAX:
dhcp server option ruledelete name = <>
rulename = <>
where:
name
The name of the DHCP server option instance.
REQUIRED
REQUIRED
rulename
The name of the DHCP selection rule.
E-DOC-CTC-20071119-0014 v1.0
161
Download from Www.Somanuals.com. All Manuals Search And Download.
dhcp Commands
dhcp server option tmpladd
Add a DHCP server option template
SYNTAX:
dhcp server option tmpladd
name = <string>
optionid = <number{1-254}>
[dynamic = <{disabled|enabled}]>
where:
name
The name of the DHCP server option template.
Specify the DHCP server option code.
REQUIRED
REQUIRED
OPTIONAL
optionid
dynamic
Enable/Disable option template as dynamic.
E-DOC-CTC-20071119-0014 v1.0
162
Download from Www.Somanuals.com. All Manuals Search And Download.
dhcp Commands
dhcp server policy
Print DHCP server policy settings
SYNTAX:
dhcp server policy
[verifyfirst = <{disabled|enabled}]>
[trustclient = <{disabled|enabled}]>
[rtbehaviour = <{traditional|standard|msft}]>
where:
verifyfirst
Enable/Disable IP address conflict network
probing before handing out an address to a
client.
OPTIONAL
trustclient
Whether or not the IP address suggested by a
DHCP client should be taken into account.
OPTIONAL
OPTIONAL
rtbehaviour
Define the DHCP Server's route options
behaviour. The options that are involved are: 3,
33, 121 and 249. "Traditional" will return 3 and/
or 33; "standard" will return 3 and/or 33 or 121;
"msft" will return 3 and/or 33 or 121 or 249
E-DOC-CTC-20071119-0014 v1.0
165
Download from Www.Somanuals.com. All Manuals Search And Download.
dhcp Commands
dhcp server pool add
Add a DHCP server pool
SYNTAX:
dhcp server pool add
name = <string>
[index = <number]>
where:
name
index
The name of the DHCP server pool.
REQUIRED
The number of the pool before which you want
the new pool to be added.
OPTIONAL
E-DOC-CTC-20071119-0014 v1.0
166
Download from Www.Somanuals.com. All Manuals Search And Download.
dhcp Commands
dhcp server pool config
Configure a DHCP server pool
SYNTAX:
dhcp server pool config
name = <{LAN_private}>
[state = <{disabled|enabled}]>
[intf = <{Internet|LocalNetwork}]>
[index = <number]>
[poolstart = <ip-address]>
[poolend = <ip-address]>
[netmask = <ip-mask(dotted or cidr)]>
[gateway = <ip-address|0|none]>
[server = <ip-address|none]>
[primdns = <ip-address|none]>
[secdns = <ip-address|none]>
[dnsmetric = <number{0-100}]>
[primwins = <ip-address|none]>
[secwins = <ip-address|none]>
[leasetime = <number{0-1814400}]>
[renewtime = <number{0-1814400}]>
[rebindtime = <number{0-1814400}]>
[unnumbered = <{disabled|enabled}]>
[localgw = <{disabled|enabled}]>
where:
name
state
The name of the DHCP server pool.
REQUIRED
OPTIONAL
Enable/Disable the DHCP server pool admin
state.
intf
The interface for which the pool is allowed to
lease IP addresses.
OPTIONAL
OPTIONAL
index
The number of the pool before which you want
the new pool to be added.
poolstart
poolend
netmask
gateway
The DHCP server pool start IP address.
The DHCP server pool end IP address.
The DHCP server pool netmask.
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
The IP address of the default router for DHCP
clients.
server
The IP address of the DHCP server for DHCP
clients.
OPTIONAL
OPTIONAL
primdns
The IP address of the primary DNS server for
DHCP clients.
E-DOC-CTC-20071119-0014 v1.0
167
Download from Www.Somanuals.com. All Manuals Search And Download.
dhcp Commands
secdns
The IP address of the secondary DNS server for
DHCP clients.
OPTIONAL
dnsmetric
primwins
The DHCP server pool DNS route metric.
OPTIONAL
OPTIONAL
The IP address of the primary WINS server for
DHCP clients.
secwins
The IP address of the secondary WINS server for OPTIONAL
DHCP clients.
leasetime
renewtime
rebindtime
unnumbered
localgw
The time in seconds a client is allowed to use an
address (tip: 0 means infinite lease).
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
The time in seconds before a client switches to
renewing.
The time in seconds before a client switches to
rebinding.
Assign an IP address from this pool to the DHCP
server or not (ppp pools only).
Proxy for a virtual default gateway residing
in same subnet of DHCP client instead of the
remote peer address.
E-DOC-CTC-20071119-0014 v1.0
168
Download from Www.Somanuals.com. All Manuals Search And Download.
dhcp Commands
dhcp server pool optadd
Add an option instance to the DHCP server pool
SYNTAX:
dhcp server pool optadd
name = <{LAN_private}>
instname = <>
where:
name
The name of the DHCP server pool.
REQUIRED
instname
The name of the DHCP server option instance.
REQUIRED
E-DOC-CTC-20071119-0014 v1.0
172
Download from Www.Somanuals.com. All Manuals Search And Download.
dhcp Commands
dhcp server pool optdelete
Delete an option instance from the DHCP server pool
SYNTAX:
dhcp server pool optdelete
name = <{LAN_private}>
instname = <>
where:
name
The name of the DHCP server pool.
REQUIRED
REQUIRED
instname
The name of the DHCP server option instance.
E-DOC-CTC-20071119-0014 v1.0
173
Download from Www.Somanuals.com. All Manuals Search And Download.
dhcp Commands
dhcp server pool rtadd
Add a route to the DHCP server pool
SYNTAX:
dhcp server pool rtadd
name = <{LAN_private}>
dst = <ip-address>
[dstmsk = <ip-mask(dotted or cidr)]>
[gateway = <ip-address|0]>
where:
name
dst
The name of the DHCP server pool.
REQUIRED
The IP destination address of the route for DHCP REQUIRED
clients.
dstmsk
The destination IP address mask.
OPTIONAL
OPTIONAL
gateway
The IP address of the next hop. Must be directly
connected to the DHCP client
E-DOC-CTC-20071119-0014 v1.0
174
Download from Www.Somanuals.com. All Manuals Search And Download.
dhcp Commands
dhcp server pool rtdelete
Delete a route from the DHCP server pool
SYNTAX:
dhcp server pool rtdelete
name = <{LAN_private}>
dst = <ip-address>
[dstmsk = <ip-mask(dotted or cidr)]>
[gateway = <ip-address|0]>
where:
name
dst
The name of the DHCP server pool.
REQUIRED
The IP destination address of the route for DHCP REQUIRED
clients.
dstmsk
The destination IP address mask.
OPTIONAL
OPTIONAL
gateway
The IP address of the next hop. Must be directly
connected to the DHCP client
E-DOC-CTC-20071119-0014 v1.0
175
Download from Www.Somanuals.com. All Manuals Search And Download.
dhcp Commands
dhcp server pool ruleadd
Add a selection rule to the DHCP server pool
SYNTAX:
dhcp server pool ruleadd
name = <{LAN_private}>
[key = <{or|and}]>
rulename = <>
where:
name
key
The name of the DHCP server pool.
The logical key of the selection rule.
The name of the DHCP selection rule.
REQUIRED
OPTIONAL
REQUIRED
rulename
E-DOC-CTC-20071119-0014 v1.0
176
Download from Www.Somanuals.com. All Manuals Search And Download.
dhcp Commands
dhcp server pool ruledelete
Delete a selection rule from the DHCP server pool
SYNTAX:
dhcp server pool ruledelete
name = <{LAN_private}>
rulename = <>
where:
name
The name of the DHCP server pool.
The name of the DHCP selection rule.
REQUIRED
REQUIRED
rulename
E-DOC-CTC-20071119-0014 v1.0
177
Download from Www.Somanuals.com. All Manuals Search And Download.
dhcp Commands
dhcp spoofing add
Add a Spoofing-Association
SYNTAX:
dhcp spoofing add
name = <string>
pool_name = <{LAN_private}>
ifname = <>
where:
name
The name of the Association.
REQUIRED
REQUIRED
pool_name
ifname
The name of the pool to be associated.
The name of the interface on which a DHCP
Client is defined.
REQUIRED
E-DOC-CTC-20071119-0014 v1.0
178
Download from Www.Somanuals.com. All Manuals Search And Download.
dhcp Commands
dhcp spoofing debug traceconfig
Display/modify DHCP spoofing trace configuratin
SYNTAX:
dhcp spoofing debug
traceconfig
[state = <{disabled|enabled}]>
where:
state
Enable/Disable tracing.
OPTIONAL
E-DOC-CTC-20071119-0014 v1.0
181
Download from Www.Somanuals.com. All Manuals Search And Download.
dhcp Commands
dhcp spoofing option-add
Add a DHCP Option Code to a Spoofing-Association.
SYNTAX:
dhcp spoofing option-add
name = <{|||}>
option = <number>
where:
name
The name of the Association.
The option id.
REQUIRED
REQUIRED
option
E-DOC-CTC-20071119-0014 v1.0
186
Download from Www.Somanuals.com. All Manuals Search And Download.
dhcp Commands
dhcp spoofing option-delete
Delete a DHCP Option Code from a Spoofing-Association.
SYNTAX:
dhcp spoofing option-delete
name = <{|||}>
option = <number>
where:
name
The name of the Association.
The option id.
REQUIRED
REQUIRED
option
E-DOC-CTC-20071119-0014 v1.0
187
Download from Www.Somanuals.com. All Manuals Search And Download.
dns Commands
E-DOC-CTC-20071119-0014 v1.0
188
Download from Www.Somanuals.com. All Manuals Search And Download.
dns Commands
dns client config
Modify the DNS resolver configuration.
SYNTAX:
dns client config
[timeout = <number{1-900}]>
[retry = <number{0-10}]>
[search = <{disabled|enabled}]>
[list = <string]>
[trace = <{disabled|enabled}]>
where:
timeout
retry
The query timeout in seconds.
OPTIONAL
OPTIONAL
OPTIONAL
The number of query retries before giving up.
search
Use the searchlist to construct fully qualified
domain names.
list
Slash separated list of domain name suffixes.
Enable or disable verbose logging.
OPTIONAL
OPTIONAL
trace
E-DOC-CTC-20071119-0014 v1.0
190
Download from Www.Somanuals.com. All Manuals Search And Download.
dns Commands
dns server config
DNS server configuration settings
SYNTAX:
dns server config
[domain = <string]>
[timeout = <number{0-2147483647}]>
[suppress = <number]>
[state = <{disabled|enabled}]>
[trace = <{disabled|enabled}]>
[syslog = <{disabled|enabled}]>
[WANDownSpoofing = <{disabled|enabled}]>
[WDSpoofedIP = <ip-address]>
where:
domain
timeout
suppress
The DNS server domain name.
OPTIONAL
The forwarded DNS query timeout.
OPTIONAL
OPTIONAL
Suppress not more than specified amount of
remote DNS server errors.
state
Enable/disable the local DNS server/forwarder.
Enable/disable verbose console logging.
Enable/disable SYSLOG for DNS events.
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
trace
syslog
WANDownSpoofing
Enable/disable DNS spoofing when no
applicable forwarding route present.
WDSpoofedIP
IP address used for spoofing when
WANDownSpoofing enabled.
OPTIONAL
E-DOC-CTC-20071119-0014 v1.0
196
Download from Www.Somanuals.com. All Manuals Search And Download.
dns Commands
dns server host add
Add a local DNS host
SYNTAX:
dns server host add
name = <string>
[addr = <ip-address]>
[ttl = <number{0-2147483647}]>
where:
name
addr
ttl
The name of an IP host to add.
The IP address of the host.
The lifetime of the host.
REQUIRED
OPTIONAL
OPTIONAL
E-DOC-CTC-20071119-0014 v1.0
205
Download from Www.Somanuals.com. All Manuals Search And Download.
dns Commands
dns server route add
Creates a DNS forwarding entry or template
SYNTAX:
dns server route add
dns = <ip-address>
[src = <ip-address]>
[srcmask = <ip-mask(dotted or cidr)]>
[domain = <string]>
[metric = <number{0-100}]>
[label = <{None|DSCP|Interactive|Management|
Video|VoIP-RTP|VoIP-Signal|default}]>
[intf = <{loop|Internet|LocalNetwork}]>
where:
dns
The IP address of a DNS server. If 0.0.0.0 is used, REQUIRED
the entry becomes a DNS-Template which is
instantiated if DNS Server IPs are configured on
an IP interface.
src
If specified, only DNS queries from machines of
which the source IP address matches the source
prefix of the DNS entry will be forwarded to the
corresponding DNS server.
OPTIONAL
srcmask
domain
The IP address mask for the source prefix.
OPTIONAL
OPTIONAL
Domain matching string. If configured, only
those DNS queries of which the domain name in
the query matches with the string configured for
the entry will be forwarded to the corresponding
DNS Server. Maximum string length: 62
characters
metric
The metric for the DNS entry. The DNS Entry List OPTIONAL
is sorted on DNS Metric; the lower the metric,
the higher the priority of the entry.
label
intf
The label associated with the DNS entry or DNS
Template.
OPTIONAL
The interface associated with the DNS entry or
DNS Template.
OPTIONAL
E-DOC-CTC-20071119-0014 v1.0
209
Download from Www.Somanuals.com. All Manuals Search And Download.
dns Commands
dns server route delete
Deletes a DNS forwarding entry or template
SYNTAX:
dns server route delete
dns = <ip-address>
[domain = <string]>
[intf = <{loop|Internet|LocalNetwork}]>
where:
dns
The IP address of a DNS server.
The DNS domain string.
REQUIRED
domain
intf
OPTIONAL
OPTIONAL
The interface associated with the DNS entry or
DNS Template.
E-DOC-CTC-20071119-0014 v1.0
210
Download from Www.Somanuals.com. All Manuals Search And Download.
dsd Commands
dsd debug proxy
Display/modify HTTPI fixed proxy settings
SYNTAX:
dsd debug proxy
[state = <{disabled|enabled}]>
[dest = <ip-address]>
[port = <{at-echo|at-nbp|at-rtmp|at-zis|auth|
bgp|biff|bootpc|bootps|chargen|data|gopher|
h323|httpproxy|ike|ils|imap2|imap3|ingres-
net|ipcserver|ipx|irc-o|irc-u|kerberos|ldap|
login|netbios-dgm|netbios-ns|netbios-ssn|
netwall|netware-ip|new-rwho|nfds|nicname|nntp|
ntalk|ntp|pcmail-srv|pop2|pop3|printer|qotd|
realaudio|rip|rtelnet|rtsp|sip|smtp|snmp|
snmptrap|snpp|sntp|sql*net|sql-net|sqlserv|
sunrpc|syslog|systat|talk|telnet|...} or
number]>
where:
state
dest
Enable/disable fixed proxy redirecting
OPTIONAL
OPTIONAL
Destination IP where requests will be forwarded
to
port
Port used for connecting to the proxy IP
OPTIONAL
E-DOC-CTC-20071119-0014 v1.0
217
Download from Www.Somanuals.com. All Manuals Search And Download.
dsd Commands
dsd debug recycling
Display/modify HTTPI recycling settings
SYNTAX:
dsd debug recycling
[state = <{disabled|enabled}]>
[interval = <number]>
[httpidle = <number]>
[otheridle = <number]>
where:
state
Enable/disable stream recycling
OPTIONAL
OPTIONAL
interval
httpidle
Time between successive activity checks
Minimal idle count for recycling (filtered) http
streams
OPTIONAL
otheridle
Minimal idle count for recycling other streams
OPTIONAL
E-DOC-CTC-20071119-0014 v1.0
218
Download from Www.Somanuals.com. All Manuals Search And Download.
dsd Commands
dsd debug stats
Display/clear DSD framework and module statistics
SYNTAX:
dsd debug stats
[name = <{intercept|urlfilter|recycling|
syslog|all}]>
[clear = <{no|yes}]>
where:
name
clear
Specify the name of a module
Clear the specified statistics
OPTIONAL
OPTIONAL
E-DOC-CTC-20071119-0014 v1.0
219
Download from Www.Somanuals.com. All Manuals Search And Download.
dsd Commands
dsd intercept config
Display/modify HTTP Intercept configuration
SYNTAX:
dsd intercept config
[WDSpoofedIP = <ip-address]>
[servertimeout = <number]>
[connecterrorurl = <string]>
[categoryerrorurl = <string]>
[monitorintercepturl = <string]>
[unauthorizedrequrl = <string]>
[imageredirect = <{disabled|enabled}]>
[imageredirecturl = <string]>
[alwaysuseip = <{disabled|enabled}]>
where:
WDSpoofedIP
IP address indicating unavailable WAN
connection.
OPTIONAL
servertimeout
connecterrorurl
categoryerrorurl
Server timeout for redirect action
OPTIONAL
OPTIONAL
OPTIONAL
Destination url when connection to server failed
Destination url when connection to category
server failed
monitorintercepturl
unauthorizedrequrl
Destination url when request is intercepted by
monitor thread
OPTIONAL
OPTIONAL
Destination url when requested url is blocked by
some rule or setting
imageredirect
Enable/disable substituting blocked images
OPTIONAL
OPTIONAL
imageredirecturl
URL of image used when substituting blocked
images
alwaysuseip
Always use ip address when redirecting to a
local page
OPTIONAL
E-DOC-CTC-20071119-0014 v1.0
220
Download from Www.Somanuals.com. All Manuals Search And Download.
dsd Commands
dsd syslog config
Display/modify HTTPI logging configuration
SYNTAX:
dsd syslog config
[syslog = <{none|unauthorized|errors|
intercepted|all}]>
where:
syslog
Define which type of events to log
OPTIONAL
E-DOC-CTC-20071119-0014 v1.0
221
Download from Www.Somanuals.com. All Manuals Search And Download.
dsd Commands
dsd urlfilter config
Display/modify url filtering configuration
SYNTAX:
dsd urlfilter config
[state = <{disabled|enabled}]>
[blockproxy = <{disabled|enabled}]>
[blockipaddress = <{disabled|enabled}]>
[blockobscuredip = <{disabled|enabled}]>
[defaultaction = <{block|accept}]>
where:
state
Enable/disable url filtering
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
blockproxy
blockipaddress
blockobscuredip
Block HTTP requests via a proxy server
Block HTTP requests if host name is IP address
Block HTTP requests if host name is believed to
be an IP address
defaultaction
Action to perform when no filter applicable.
OPTIONAL
E-DOC-CTC-20071119-0014 v1.0
223
Download from Www.Somanuals.com. All Manuals Search And Download.
dsd Commands
dsd urlfilter rule add
Add a rule
SYNTAX:
dsd urlfilter rule add
url = <string>
action = <{block|accept|redirect}>
redirect = <string>
where:
url
Definition of the url filter
Action to perform when url matches url
Redirection url
REQUIRED
REQUIRED
REQUIRED
action
redirect
E-DOC-CTC-20071119-0014 v1.0
224
Download from Www.Somanuals.com. All Manuals Search And Download.
dsd Commands
dsd urlfilter rule delete
Remove a rule
SYNTAX:
dsd urlfilter rule delete
index = <number>
[url = <string]>
where:
index
url
Insertion position in the list
Definition of the url filter
REQUIRED
OPTIONAL
E-DOC-CTC-20071119-0014 v1.0
225
Download from Www.Somanuals.com. All Manuals Search And Download.
dsd Commands
dsd urlfilter rule modify
Modify an existing rule
SYNTAX:
dsd urlfilter rule modify
index = <number>
[newurl = <string]>
action = <{block|accept|redirect}>
redirect = <string>
where:
index
Insertion position in the list
Definition of the new url filter
Action to perform when url matches url
Redirection url
REQUIRED
OPTIONAL
REQUIRED
REQUIRED
newurl
action
redirect
E-DOC-CTC-20071119-0014 v1.0
228
Download from Www.Somanuals.com. All Manuals Search And Download.
dyndns Commands
dyndns host add
Add a fully qualified host name
SYNTAX:
dyndns host add
group = <>
name = <string>
where:
group
name
The dynamic DNS host group.
The name of an IP host to add.
REQUIRED
REQUIRED
E-DOC-CTC-20071119-0014 v1.0
233
Download from Www.Somanuals.com. All Manuals Search And Download.
dyndns Commands
dyndns modify
Modify a dynamic DNS client.
SYNTAX:
dyndns modify
name = <>
[intf = <{loop|Internet|LocalNetwork}]>
[user = <string]>
[password = <password]>
[group = <]>
[mx = <string]>
[backmx = <{disabled|enabled}]>
[wildcard = <{disabled|enabled}]>
[offline = <{disabled|enabled}]>
[service = <{dyndns|statdns|custom|No-IP|
DtDNS|gnudip}]>
[status = <{disabled|enabled}]>
[trace = <{disabled|enabled}]>
where:
name
intf
The dynamic DNS client name.
REQUIRED
The dynamic DNS client interface.
The username for dynamic DNS authentication.
The password for dynamic DNS authentication.
The dynamic DNS host group.
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
user
password
group
mx
The mail exchanger.
backmx
wildcard
offline
service
status
trace
Set up the mail exchanger as a backup MX.
Allow use of hostname wildcards.
Set the host to offline mode.
The dynamic DNS service.
Enable/Disable the dynamic DNS client.
Enable/Disable the verbose console logging for
the dynamic DNS client.
E-DOC-CTC-20071119-0014 v1.0
238
Download from Www.Somanuals.com. All Manuals Search And Download.
dyndns Commands
dyndns service modify
Modify specific dynamic DNS service settings
SYNTAX:
dyndns service modify
name = <{dyndns|statdns|custom|No-IP|DtDNS|
gnudip}>
[server = <string]>
[port = <{at-echo|at-nbp|at-rtmp|at-zis|auth|
bgp|biff|bootpc|bootps|chargen|data|gopher|
h323|httpproxy|ike|ils|imap2|imap3|ingres-
net|ipcserver|ipx|irc-o|irc-u|kerberos|ldap|
login|netbios-dgm|netbios-ns|netbios-ssn|
netwall|netware-ip|new-rwho|nfds|nicname|nntp|
ntalk|ntp|pcmail-srv|pop2|pop3|printer|qotd|
realaudio|rip|rtelnet|rtsp|sip|smtp|snmp|
snmptrap|snpp|sntp|sql*net|sql-net|sqlserv|
sunrpc|syslog|systat|talk|telnet|...} or
number]>
[request = <string]>
[updateinterval = <number{0-2097120}]>
[retryinterval = <number{0-600}]>
[max_retry = <number{1-5}]>
where:
name
The dynamic DNS service.
REQUIRED
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
server
The dynamic DNS server hostname.
The dynamic DNS server port.
The dynamic DNS request string.
port
request
updateinterval
Number of seconds before a dynamic update
is sent to the dynamic DNS server (The value 0
means disabled).
retryinterval
max_retry
Number of seconds between retries if
communication with the dynamic DNS server
fails (The value 0 means disabled).
OPTIONAL
OPTIONAL
The maximum number of retries if
communication with the dynamic DNS server
fails.
E-DOC-CTC-20071119-0014 v1.0
240
Download from Www.Somanuals.com. All Manuals Search And Download.
env Commands
env get
Gets an environment variable.
SYNTAX:
env get
var = <{_ETHERNET|_COMPANY_NAME|_COMPANY_URL|
_PROD_NAME|_PROD_URL|_PROD_SERIAL_NBR|_FII|
_BUILD|_BOOTLOADER_VERSION|_BUILDVARIANT|
_MODEM_ACCESS_CODE|__SEC_MODEM_ACCESS_CODE|
_OUI|_CUSTOVARIANT|_PHYSLAYERTYPE|_BUILDNAME|
_PRL|_FIA|_BOARD_NAME|_COMPANY_ID|_COPYRIGHT|
_TPVERSION|_PROD_ID|_PROD_FRIENDLY_NAME|
_VARIANT_ID|_VARIANT_FRIENDLY_NAME|
_MACADDR|_LMACADDR|_WL0_WEPKEY_SERIAL|
_WL0_WPAKEY_SERIAL|_WL0_SSID_SERIAL|
_WL0_SSID_PREFIX|_WL_VERSION}>
where:
var
The name of the variable.
REQUIRED
E-DOC-CTC-20071119-0014 v1.0
243
Download from Www.Somanuals.com. All Manuals Search And Download.
env Commands
env set
Sets an environment variable.
SYNTAX:
env set
var = <string>
value = <translated string>
where:
var
The name of the variable.
REQUIRED
REQUIRED
value
A translated quoted string defining the variable
value.
E-DOC-CTC-20071119-0014 v1.0
245
Download from Www.Somanuals.com. All Manuals Search And Download.
env Commands
env unset
Deletes an environment variable.
SYNTAX:
env unset
var = <{_ETHERNET|_COMPANY_NAME|_COMPANY_URL|
_PROD_NAME|_PROD_URL|_PROD_SERIAL_NBR|_FII|
_BUILD|_BOOTLOADER_VERSION|_BUILDVARIANT|
_MODEM_ACCESS_CODE|__SEC_MODEM_ACCESS_CODE|
_OUI|_CUSTOVARIANT|_PHYSLAYERTYPE|_BUILDNAME|
_PRL|_FIA|_BOARD_NAME|_COMPANY_ID|_COPYRIGHT|
_TPVERSION|_PROD_ID|_PROD_FRIENDLY_NAME|
_VARIANT_ID|_VARIANT_FRIENDLY_NAME|
_MACADDR|_LMACADDR|_WL0_WEPKEY_SERIAL|
_WL0_WPAKEY_SERIAL|_WL0_SSID_SERIAL|
_WL0_SSID_PREFIX|_WL_VERSION}>
where:
var
The name of the variable.
REQUIRED
E-DOC-CTC-20071119-0014 v1.0
246
Download from Www.Somanuals.com. All Manuals Search And Download.
eth Commands
E-DOC-CTC-20071119-0014 v1.0
248
Download from Www.Somanuals.com. All Manuals Search And Download.
eth Commands
E-DOC-CTC-20071119-0014 v1.0
249
Download from Www.Somanuals.com. All Manuals Search And Download.
eth Commands
E-DOC-CTC-20071119-0014 v1.0
250
Download from Www.Somanuals.com. All Manuals Search And Download.
eth Commands
eth bridge config
Modify/Display the bridge configuration settings.
SYNTAX:
eth bridge config
[brname = <{bridge}]>
[age = <number{10-1000000}]>
[filter = <{none|no_WAN_broadcast}]>
[vlan = <{disabled|enabled}]>
[precedencemap = <string]>
where:
brname
age
The name of a bridge instance.
OPTIONAL
OPTIONAL
The lifetime (in seconds) of a dynamically
learned MAC address.
filter
The bridge filter to be applied for all WAN bridge OPTIONAL
interfaces.
vlan
Enable/disable the use of the VLAN id of the
received VLAN packets.
OPTIONAL
precedencemap
The IP QoS precedence mapping table.
OPTIONAL
E-DOC-CTC-20071119-0014 v1.0
253
Download from Www.Somanuals.com. All Manuals Search And Download.
eth Commands
eth bridge dynvlan add
Add a dynamic VLAN membership entry.
SYNTAX:
eth bridge dynvlan add
[id = <number{0-100000}]>
hwaddr = <masked-hardware-address>
vlan = <{default}>
[remvlan = <{default}]>
where:
id
The id of the dynamic VLAN membership entry.
OPTIONAL
REQUIRED
hwaddr
The (masked) ethernet MAC address of the
dynamic VLAN membership entry.
vlan
The VLAN for the dynamic VLAN membership
entry.
REQUIRED
OPTIONAL
remvlan
The VLAN that will be removed from the bridge
interface.
E-DOC-CTC-20071119-0014 v1.0
256
Download from Www.Somanuals.com. All Manuals Search And Download.
eth Commands
eth bridge dynvlan config
Modify the dynamic VLAN membership configuration.
SYNTAX:
eth bridge dynvlan config
[timeout = <number{0-100000}]>
where:
timeout
Timeout in seconds for the dynamic entries.
OPTIONAL
E-DOC-CTC-20071119-0014 v1.0
257
Download from Www.Somanuals.com. All Manuals Search And Download.
eth Commands
eth bridge ifadd
Add a new bridge interface.
SYNTAX:
eth bridge ifadd
[brname = <{bridge}]>
intf = <string>
where:
brname
intf
The name of a bridge instance.
The new bridge interface name.
OPTIONAL
REQUIRED
E-DOC-CTC-20071119-0014 v1.0
262
Download from Www.Somanuals.com. All Manuals Search And Download.
eth Commands
eth bridge ifattach
Attach a bridge interface.
SYNTAX:
eth bridge ifattach
[brname = <{bridge}]>
intf = <{}>
where:
brname
intf
The name of a bridge instance.
The name of the bridge interface.
OPTIONAL
REQUIRED
E-DOC-CTC-20071119-0014 v1.0
263
Download from Www.Somanuals.com. All Manuals Search And Download.
eth Commands
eth bridge ifconfig
Modify a bridge interface configuration.
SYNTAX:
eth bridge ifconfig
[brname = <{bridge}]>
intf = <{OBC|ethport1|ethport2|ethport3|
ethport4|WLAN}>
[dest = <{}]>
[portstate = <{disabled|learning|forwarding}]>
[retry = <number{0-65535}]>
[priotag = <{disabled|enabled}]>
[vlan = <{default}]>
[prioconfig = <{disabled|overwrite|increase}]>
[ipprec = <{disabled|precedence|dscp}]>
[priority = <number{0-7}]>
[regenprio = <string]>
[ingressfiltering = <{disabled|enabled}]>
[acceptvlanonly = <{disabled|enabled}]>
[mcastfilter = <{disabled|enabled}]>
[dynvlan = <{disabled|enabled}]>
[wan = <{disabled|enabled}]>
[igmpsnooping = <{disabled|enabled}]>
[priotransparent = <{disabled|enabled}]>
[bpdufiltering = <{disabled|enabled}]>
[xtratagging = <{none|c-vlan|s-vlan}]>
where:
brname
intf
The name of a bridge instance.
OPTIONAL
REQUIRED
OPTIONAL
The name of the bridge interface to configure.
dest
The destination for this interface. Typically an
ATM or a physical interface name.
portstate
retry
The bridge portstate for this interface.
OPTIONAL
OPTIONAL
The number of WAN connection setup retries
before giving up.
priotag
vlan
Enable/Disable priority tagging.
The default VLAN.
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
prioconfig
ipprec
The priority configuration for this interface.
The IP precedence for this interface.
priority
The default priority for untagged ingress
packets.
E-DOC-CTC-20071119-0014 v1.0
264
Download from Www.Somanuals.com. All Manuals Search And Download.
eth Commands
regenprio
The priority regeneration table for tagged
ingress packets.
OPTIONAL
ingressfiltering
Enable/disable discard of tagged ingress packets OPTIONAL
if the interface is not part of the VLAN.
acceptvlanonly
mcastfilter
Enable/disable receipt of tagged ingress packets. OPTIONAL
Enable/disable discard of multicast packets for
this interface.
OPTIONAL
dynvlan
Enable/disable dynamic VLAN membership
checking for this interface.
OPTIONAL
wan
Enable/disable WAN for this interface.
OPTIONAL
OPTIONAL
OPTIONAL
igmpsnooping
priotransparent
Enable/disable IGMP snooping for this interface.
Enable/disable priority preservation for this
interface.
bpdufiltering
xtratagging
Enable/disable BPDU filtering for this interface.
OPTIONAL
The 'extra tagging mode' for this interface (none, OPTIONAL
c-vlan or s-vlan).
E-DOC-CTC-20071119-0014 v1.0
265
Download from Www.Somanuals.com. All Manuals Search And Download.
eth Commands
eth bridge ifdelete
Delete a bridge interface.
SYNTAX:
eth bridge ifdelete
[brname = <{bridge}]>
intf = <{ethport1|ethport2|ethport3|ethport4|
WLAN}>
where:
brname
intf
The name of a bridge instance.
The name of the bridge interface.
OPTIONAL
REQUIRED
E-DOC-CTC-20071119-0014 v1.0
266
Download from Www.Somanuals.com. All Manuals Search And Download.
eth Commands
eth bridge ifdetach
Detach a bridge interface.
SYNTAX:
eth bridge ifdetach
[brname = <{bridge}]>
intf = <{ethport1|ethport2|ethport3|ethport4|
WLAN}>
where:
brname
intf
The name of a bridge instance.
The name of the bridge interface.
OPTIONAL
REQUIRED
E-DOC-CTC-20071119-0014 v1.0
267
Download from Www.Somanuals.com. All Manuals Search And Download.
eth Commands
eth bridge iflist
Display the current bridge interfaces.
SYNTAX:
eth bridge iflist
[brname = <{bridge}]>
[intf = <{OBC|ethport1|ethport2|ethport3|
ethport4|WLAN}]>
where:
brname
intf
The name of a bridge instance.
The name of a bridge interface.
OPTIONAL
OPTIONAL
E-DOC-CTC-20071119-0014 v1.0
269
Download from Www.Somanuals.com. All Manuals Search And Download.
eth Commands
eth bridge igmpsnooping clear
Clear snooping statistics.
SYNTAX:
eth bridge igmpsnooping clear [brname = <{bridge}]>
[intf = <{OBC|ethport1|ethport2|ethport3|
ethport4|WLAN}]>
where:
brname
intf
The name of a bridge instance.
OPTIONAL
OPTIONAL
The bridge interface currently to be cleared.
E-DOC-CTC-20071119-0014 v1.0
270
Download from Www.Somanuals.com. All Manuals Search And Download.
eth Commands
eth bridge igmpsnooping config
Configure bridge instance IGMP Snooping flags.
SYNTAX:
eth bridge igmpsnooping config [brname = <{bridge}]>
[state = <{disabled|enabled}]>
[floodrp = <{disabled|enabled}]>
[floodmcast = <{disabled|enabled}]>
where:
brname
state
The name of a bridge instance.
OPTIONAL
OPTIONAL
OPTIONAL
Enable/Disable the IGMP Snooping.
Enable/Disable flooding reports to all ports.
floodrp
floodmcast
Enable/Disable flooding unregistered multicasts. OPTIONAL
E-DOC-CTC-20071119-0014 v1.0
271
Download from Www.Somanuals.com. All Manuals Search And Download.
eth Commands
eth bridge igmpsnooping ifconfig
Configure bridge interface IGMP snooping flags and mode.
SYNTAX:
eth bridge igmpsnooping
ifconfig
[brname = <{bridge}]>
intf = <{OBC|ethport1|ethport2|ethport3|
ethport4|WLAN}>
[portmode = <{Host|Router|Auto}]>
[fastleave = <{disabled|enabled}]>
[exptrack = <{disabled|enabled}]>
[mrdp = <{disabled|enabled}]>
[rgmp = <{disabled|enabled}]>
where:
brname
intf
The bridge instance currently to be configured.
The bridge interface currently to be configured.
Mode of the bridge port.
OPTIONAL
REQUIRED
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
portmode
fastleave
exptrack
mrdp
Enable/Disable Fast Immediate Leave.
Enable/Disable Explicit Host Tracking.
Enable/Disable MRDP support.
rgmp
Enable/Disable RGMP support.
E-DOC-CTC-20071119-0014 v1.0
272
Download from Www.Somanuals.com. All Manuals Search And Download.
eth Commands
eth bridge igmpsnooping iflist
Display bridge interface IGMP status.
SYNTAX:
eth bridge igmpsnooping iflist [brname = <{bridge}]>
[intf = <{OBC|ethport1|ethport2|ethport3|
ethport4|WLAN}]>
where:
brname
intf
The name of a bridge instance.
The name of the bridge interface.
OPTIONAL
OPTIONAL
E-DOC-CTC-20071119-0014 v1.0
273
Download from Www.Somanuals.com. All Manuals Search And Download.
eth Commands
eth bridge macadd
Add a static MAC address to a bridge interface.
SYNTAX:
eth bridge macadd
[brname = <{bridge}]>
intf = <{OBC|ethport1|ethport2|ethport3|
ethport4|WLAN}>
hwaddr = <hardware-address>
[vlan = <{default}]>
where:
brname
intf
The name of a bridge instance.
The name of the bridge interface.
The ethernet MAC address of the new entry.
The VLAN.
OPTIONAL
REQUIRED
REQUIRED
OPTIONAL
hwaddr
vlan
E-DOC-CTC-20071119-0014 v1.0
276
Download from Www.Somanuals.com. All Manuals Search And Download.
eth Commands
eth bridge macdelete
Remove a MAC address from the database.
SYNTAX:
eth bridge macdelete
[brname = <{bridge}]>
hwaddr = <hardware-address>
[vlan = <{default}]>
where:
brname
hwaddr
vlan
The name of a bridge instance.
The ethernet MAC address of the entry.
The VLAN.
OPTIONAL
REQUIRED
OPTIONAL
E-DOC-CTC-20071119-0014 v1.0
277
Download from Www.Somanuals.com. All Manuals Search And Download.
eth Commands
eth bridge rule add
Add a new constraint to the VLAN learning system.
SYNTAX:
eth bridge rule add
type = <{shared|independant}>
vlan = <{default}>
[vlan2 = <{default}]>
[isi = <number{0-32}]>
where:
type
vlan
vlan2
isi
Type of constraint.
REQUIRED
REQUIRED
OPTIONAL
OPTIONAL
The VLAN where the constraint belongs to.
The second VLAN for a shared constraint.
The indenpendent set id for an independent
constraint.
E-DOC-CTC-20071119-0014 v1.0
279
Download from Www.Somanuals.com. All Manuals Search And Download.
eth Commands
eth bridge select
Select the default bridge for configuring interfaces from (if not setting
SYNTAX:
eth bridge select
brname = <{bridge}>
where:
brname
The name of a bridge instance.
REQUIRED
E-DOC-CTC-20071119-0014 v1.0
283
Download from Www.Somanuals.com. All Manuals Search And Download.
eth Commands
eth bridge unknownvlan ifadd
Add bridge interface to unknown 'VLAN'.
SYNTAX:
eth bridge unknownvlan ifadd
[brname = <{bridge}]>
intf = <{OBC|ethport1|ethport2|ethport3|
ethport4|WLAN}>
[untagged = <{disabled|enabled}]>
where:
brname
intf
The name of a bridge instance.
OPTIONAL
REQUIRED
The name of the bridge interface to add to the
unknown 'VLAN'.
untagged
Enable/disable interface as untagged for this
unknown 'VLAN'.
OPTIONAL
E-DOC-CTC-20071119-0014 v1.0
284
Download from Www.Somanuals.com. All Manuals Search And Download.
eth Commands
eth bridge unknownvlan ifconfig
Modify bridge interface from unknown 'VLAN'.
SYNTAX:
eth bridge unknownvlan
ifconfig
[brname = <{bridge}]>
intf = <{OBC|ethport1|ethport2|ethport3|
ethport4|WLAN}>
[untagged = <{disabled|enabled}]>
where:
brname
intf
The name of a bridge instance.
OPTIONAL
The bridge interface from the unknown 'VLAN'
to configure.
REQUIRED
untagged
Enable/disable interface as untagged for this
unknown 'VLAN'.
OPTIONAL
E-DOC-CTC-20071119-0014 v1.0
285
Download from Www.Somanuals.com. All Manuals Search And Download.
eth Commands
eth bridge unknownvlan ifdelete
Delete bridge interface from unknown 'VLAN'.
SYNTAX:
eth bridge unknownvlan
ifdelete
[brname = <{bridge}]>
intf = <{OBC|ethport1|ethport2|ethport3|
ethport4|WLAN}>
where:
brname
intf
The name of a bridge instance.
OPTIONAL
The name of the bridge interface to remove from REQUIRED
the unknown 'VLAN'.
E-DOC-CTC-20071119-0014 v1.0
286
Download from Www.Somanuals.com. All Manuals Search And Download.
eth Commands
eth bridge vlan ifadd
Add bridge interface to virtual LAN.
SYNTAX:
eth bridge vlan ifadd
name = <{default}>
intf = <{OBC|ethport1|ethport2|ethport3|
ethport4|WLAN}>
[untagged = <{disabled|enabled}]>
where:
name
intf
The VLAN name.
REQUIRED
The name of the bridge interface to add to the
VLAN.
REQUIRED
untagged
Enable/disable interface as untagged for this
VLAN.
OPTIONAL
E-DOC-CTC-20071119-0014 v1.0
288
Download from Www.Somanuals.com. All Manuals Search And Download.
eth Commands
eth bridge vlan ifconfig
Modify bridge interface from virtual LAN.
SYNTAX:
eth bridge vlan ifconfig
name = <{default}>
intf = <{OBC|ethport1|ethport2|ethport3|
ethport4|WLAN}>
untagged = <{disabled|enabled}>
where:
name
intf
The VLAN name.
REQUIRED
The bridge interface from the VLAN to configure. REQUIRED
untagged
Enable/disable interface as untagged for this
VLAN.
REQUIRED
E-DOC-CTC-20071119-0014 v1.0
289
Download from Www.Somanuals.com. All Manuals Search And Download.
eth Commands
eth bridge vlan ifdelete
Delete bridge interface from virtual LAN.
SYNTAX:
eth bridge vlan ifdelete
name = <{default}>
intf = <{OBC|ethport1|ethport2|ethport3|
ethport4|WLAN}>
where:
name
intf
The VLAN name.
REQUIRED
The name of the bridge interface to remove from REQUIRED
the VLAN.
E-DOC-CTC-20071119-0014 v1.0
290
Download from Www.Somanuals.com. All Manuals Search And Download.
eth Commands
eth bridge xtratag add
Add an extra tag mapping entry.
SYNTAX:
eth bridge xtratag add
[brname = <{bridge}]>
intf = <{OBC|ethport1|ethport2|ethport3|
ethport4|WLAN}>
innervid = <{[1-4094]|all|}>
outervid = <{[1-4094]|notag|transparant|}>
where:
brname
intf
The name of a bridge instance.
The name of the bridge interface.
OPTIONAL
REQUIRED
REQUIRED
innervid
The inner VLAN id [all,1-4094] (all = all inner vid
will be translated to the outer vid).
outervid
The outer VLAN id [notag,1-4094,transparant]
(notag: outer not tagged, transparant: tagged as
inner).
REQUIRED
E-DOC-CTC-20071119-0014 v1.0
292
Download from Www.Somanuals.com. All Manuals Search And Download.
eth Commands
eth bridge xtratag config
Configure an extra tag mapping entry.
SYNTAX:
eth bridge xtratag config
[brname = <{bridge}]>
intf = <{OBC|ethport1|ethport2|ethport3|
ethport4|WLAN}>
innervid = <{[1-4094]|all|}>
outervid = <{[1-4094]|notag|transparant|}>
where:
brname
intf
The name of a bridge instance.
The name of the bridge interface.
OPTIONAL
REQUIRED
REQUIRED
innervid
The inner VLAN id [all,1-4094] (all = all inner vid
will be translated to the outer vid).
outervid
The outer VLAN id [notag,1-4094,transparant]
(notag: outer not tagged, transparant: tagged as
inner).
REQUIRED
E-DOC-CTC-20071119-0014 v1.0
293
Download from Www.Somanuals.com. All Manuals Search And Download.
eth Commands
eth bridge xtratag delete
Delete an extra tag mapping entry.
SYNTAX:
eth bridge xtratag delete
[brname = <{bridge}]>
intf = <{OBC|ethport1|ethport2|ethport3|
ethport4|WLAN}>
innervid = <{[1-4094]|all|}>
where:
brname
intf
The name of a bridge instance.
The name of the bridge interface.
OPTIONAL
REQUIRED
REQUIRED
innervid
The inner VLAN id [all,1-4094] (all = all inner vid
will be translated to the outer vid).
E-DOC-CTC-20071119-0014 v1.0
294
Download from Www.Somanuals.com. All Manuals Search And Download.
eth Commands
eth device ifconfig
Configure ethernet interface.
SYNTAX:
eth device ifconfig
intf = <{ethif1|ethif2|ethif3|ethif4|wlif1}>
[type = <{auto|10BaseTHD|10BaseTFD|100BaseTHD|
100BaseTFD} or number]>
[state = <{enabled|disabled}]>
where:
intf
The name of a physical interface.
The ethernet type.
REQUIRED
OPTIONAL
OPTIONAL
type
state
The interface state.
E-DOC-CTC-20071119-0014 v1.0
297
Download from Www.Somanuals.com. All Manuals Search And Download.
eth Commands
eth ifconfig
Modify an ETH interface.
SYNTAX:
eth ifconfig
intf = <{ethoa_8_35}>
[dest = <{bridge|ethoa_8_35}]>
[retry = <number{0-65535}]>
[wan = <{disabled|enabled}]>
[priotag = <{disabled|enabled}]>
[vlan = <{default}]>
where:
intf
The name of the ETH interface to configure.
The destination interface for this ETH interface.
REQUIRED
OPTIONAL
OPTIONAL
dest
retry
The number of times the ETH connection setup
should retry before giving up.
wan
Enable/Disable WAN for this ETH interface.
Enable/Disable VLAN priority tagging.
The VLAN for this ETH interface.
OPTIONAL
OPTIONAL
OPTIONAL
priotag
vlan
E-DOC-CTC-20071119-0014 v1.0
302
Download from Www.Somanuals.com. All Manuals Search And Download.
eth Commands
eth switch group move
Move a specified port to a specified group.
SYNTAX:
eth switch group move
group = <number{0-3}>
port = <number{1-4}>
where:
group
port
The group id.
The port.
REQUIRED
REQUIRED
E-DOC-CTC-20071119-0014 v1.0
308
Download from Www.Somanuals.com. All Manuals Search And Download.
eth Commands
eth switch mirror egress
Enable or disable the specified port to be a Transmitted Port Mirroring.
SYNTAX:
eth switch mirror egress
port = <number{1-4}>
[state = <{enabled|disabled}]>
where:
port
The port.
Enable/disable state.
REQUIRED
OPTIONAL
state
E-DOC-CTC-20071119-0014 v1.0
311
Download from Www.Somanuals.com. All Manuals Search And Download.
eth Commands
eth switch mirror ingress
Enable or disable the specified port to be a Received Port Mirroring.
SYNTAX:
eth switch mirror ingress
port = <number{1-4}>
[state = <{enabled|disabled}]>
where:
port
The port.
Enable/disable state.
REQUIRED
OPTIONAL
state
E-DOC-CTC-20071119-0014 v1.0
312
Download from Www.Somanuals.com. All Manuals Search And Download.
eth Commands
eth switch qos config
Configure common qos parameters.
SYNTAX:
eth switch qos config
state = <{enabled|disabled}>
[nbrOfQueues = <number{0-4}]>
[realtime = <{enabled|disabled}]>
where:
state
Enable/disable QoS.
Number of queues.
Enable/disable realtime.
REQUIRED
OPTIONAL
OPTIONAL
nbrOfQueues
realtime
E-DOC-CTC-20071119-0014 v1.0
313
Download from Www.Somanuals.com. All Manuals Search And Download.
eth Commands
eth switch qos ifconfig
Configure per port qos parameters.
SYNTAX:
eth switch qos ifconfig
port = <number{1-4}>
mode = <{none|802.1p|high|diffserv}>
[flowcontrol = <{disabled|enabled}]>
where:
port
The port.
REQUIRED
REQUIRED
OPTIONAL
mode
Classifier.
flowcontrol
Enable/disable flow-control.
E-DOC-CTC-20071119-0014 v1.0
314
Download from Www.Somanuals.com. All Manuals Search And Download.
eth Commands
eth switch qos weights
Configure the queue weights.
SYNTAX:
eth switch qos weights
queue0 = <number{0-100}>
queue1 = <number{0-100}>
queue2 = <number{0-100}>
queue3 = <number{0-100}>
where:
queue0
queue1
queue2
queue3
Weight of queue 0 in WFQ (in %).
Weight of queue 1 in WFQ (in %).
Weight of queue 2 in WFQ (in %).
Weight of queue 3 in WFQ (in %).
REQUIRED
REQUIRED
REQUIRED
REQUIRED
E-DOC-CTC-20071119-0014 v1.0
316
Download from Www.Somanuals.com. All Manuals Search And Download.
eth Commands
eth switch shaper config
Configure common ingress shaper parameters.
SYNTAX:
eth switch shaper config
shaper = <number{0--1}>
[unicast = <{enabled|disabled}]>
[multicast = <{enabled|disabled}]>
[broadcast = <{enabled|disabled}]>
[control = <{enabled|disabled}]>
[unknown = <{enabled|disabled}]>
[discard = <{enabled|disabled}]>
where:
shaper
The shaper instance.
REQUIRED
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
unicast
Shape unicast traffic.
multicast
broadcast
control
Shape multicast traffic.
Shape broadcast traffic.
Shape MAC control traffic.
Shape traffic with unknown destination address.
unknown
discard
Discard frame at overflow (else attempt for flow
control).
E-DOC-CTC-20071119-0014 v1.0
317
Download from Www.Somanuals.com. All Manuals Search And Download.
eth Commands
eth switch shaper ifconfig
Configure per port shaper parameters.
SYNTAX:
eth switch shaper ifconfig
port = <number{1-4}>
ingress = <{enabled|disabled}>
shaper = <number{0--1}>
[state = <{enabled|disabled}]>
[speed = <number{64000-100000000}]>
[burstsize = <{}]>
where:
port
The port.
REQUIRED
REQUIRED
REQUIRED
OPTIONAL
OPTIONAL
OPTIONAL
ingress
shaper
state
Ingress port = enabled; egress port = disabled.
The shaper instance.
Enable/disable shaping.
Speed in bits/sec.
speed
burstsize
Burst size in KBytes.
E-DOC-CTC-20071119-0014 v1.0
318
Download from Www.Somanuals.com. All Manuals Search And Download.
eth Commands
eth switch storm ifconfig
Configure per port storm control parameters.
SYNTAX:
eth switch storm ifconfig
port = <number{1-4}>
[state = <{enabled|disabled}]>
[rate = <{100|200|300|400}]>
[burstsize = <number{2-8}]>
[broadcast = <{enabled|disabled}]>
[multicast = <{enabled|disabled}]>
[unknown = <{enabled|disabled}]>
where:
port
The port.
REQUIRED
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
state
Enable/disable storm control.
Rate in 10ths of percent.
rate
burstsize
broadcast
multicast
unknown
Burst size in KBytes.
Storm control for broadcast traffic.
Storm control for multicast traffic.
Storm control for traffic with unknown
destination address.
E-DOC-CTC-20071119-0014 v1.0
323
Download from Www.Somanuals.com. All Manuals Search And Download.
eth Commands
eth vlan add
Add a new virtual LAN.
SYNTAX:
eth vlan add
name = <string>
vid = <number{2-4094}>
[addrule = <{disabled|enabled}]>
where:
name
vid
The new VLAN name.
REQUIRED
REQUIRED
OPTIONAL
The new VLAN id.
addrule
Add the default bridge constraint.
E-DOC-CTC-20071119-0014 v1.0
325
Download from Www.Somanuals.com. All Manuals Search And Download.
expr Commands
E-DOC-CTC-20071119-0014 v1.0
330
Download from Www.Somanuals.com. All Manuals Search And Download.
expr Commands
expr add
Add an expression.
SYNTAX:
expr add
name = <{wan|local|lan|tunnel|dmz|guest|
private|ssdp_ip|mdap_ip|icmp|igmp|imaps|pop2|
pop3|pop3s|smtp|ssh|dns|nntp|ipsec|esp|ah|
ike|DiffServ|sip|h323|dhcp|rtsp|ssdp_serv|
mdap_serv|syslog}>
[type = <{intf|ip|serv|mac}]>
mac [!] = <hardware-address>
addr [!] = <ip-range>
[mask [ = <ip-mask(dotted or cidr)]>
[intf [!] = <{loop|Internet|LocalNetwork}]>
[intfgroup [!] = <{wan|local|lan|tunnel|dmz|
guest} or number]>
[tos [!] = <number{0-255}]>
[precedence [!] = <{routine|priority|
immediate|flash|flash-override|CRITIC-ECP|
internetwork-control|network-control} or
number]>
[dscp [!] = <{ef|af11|af12|af13|af21|af22|
af23|af31|af32|af33|af41|af42|af43|cs0|cs1|
cs2|cs3|cs4|cs5|cs6|cs7} or number]>
[proto [!] = <{icmp|igmp|ipinip|tcp|udp|ah|
esp|ipcomp} or number]>
[srcport [!] = <{at-echo|at-nbp|at-rtmp|at-
zis|auth|bgp|biff|bootpc|bootps|finger|ftp|
ftp-data|gopher|h323|httpproxy|ike|ils|imap2|
imap3|ingres-net|ipcserver|ipx|irc-o|irc-u|
kerberos|ldap|login|netbios-dgm|netbios-ns|
netbios-ssn|netwall|netware-ip|new-rwho|nfds|
nicname|nntp|ntalk|ntp|pcmail-srv|pop2|pop3|
printer|qotd|realaudio|rip|rtelnet|rtsp|sip|
smtp|snmp|snmptrap|snpp|sntp|sql*net|sql-
net|sqlserv|sunrpc|syslog|systat|talk|...}or
number]>
[srcportend = <{at-echo|at-nbp|at-rtmp|at-
zis|auth|bgp|biff|bootpc|bootps|finger|ftp|
ftp-data|gopher|h323|httpproxy|ike|ils|imap2|
imap3|ingres-net|ipcserver|ipx|irc-o|irc-u|
kerberos|ldap|login|netbios-dgm|netbios-ns|
netbios-ssn|netwall|netware-ip|new-rwho|nfds|
nicname|nntp|ntalk|ntp|pcmail-srv|pop2|pop3|
printer|qotd|realaudio|rip|rtelnet|rtsp|sip|
smtp|snmp|snmptrap|snpp|sntp|sql*net|sql-
net|sqlserv|sunrpc|syslog|systat|talk|...}or
number]>
[dstport [!] = <{at-echo|at-nbp|at-rtmp|at-
zis|auth|bgp|biff|bootpc|bootps|finger|ftp|
E-DOC-CTC-20071119-0014 v1.0
332
Download from Www.Somanuals.com. All Manuals Search And Download.
expr Commands
ftp-data|gopher|h323|httpproxy|ike|ils|imap2|
imap3|ingres-net|ipcserver|ipx|irc-o|irc-u|
kerberos|ldap|login|netbios-dgm|netbios-ns|
netbios-ssn|netwall|netware-ip|new-rwho|nfds|
nicname|nntp|ntalk|ntp|pcmail-srv|pop2|pop3|
printer|qotd|realaudio|rip|rtelnet|rtsp|sip|
smtp|snmp|snmptrap|snpp|sntp|sql*net|sql-
net|sqlserv|sunrpc|syslog|systat|talk|...}or
number]>
[dstportend = <{at-echo|at-nbp|at-rtmp|at-
zis|auth|bgp|biff|bootpc|bootps|finger|ftp|
ftp-data|gopher|h323|httpproxy|ike|ils|imap2|
imap3|ingres-net|ipcserver|ipx|irc-o|irc-u|
kerberos|ldap|login|netbios-dgm|netbios-ns|
netbios-ssn|netwall|netware-ip|new-rwho|nfds|
nicname|nntp|ntalk|ntp|pcmail-srv|pop2|pop3|
printer|qotd|realaudio|rip|rtelnet|rtsp|sip|
smtp|snmp|snmptrap|snpp|sntp|sql*net|sql-
net|sqlserv|sunrpc|syslog|systat|talk|...}or
number]>
[icmptype [!] = <{echo-reply|destination-
unreachable|source-quench|redirect|exceeded|
parameter-problems|timestamp-request|
timestamp-reply|information-request|
information-reply|address-mask-request|
address-mask-reply} or number]>
[icmpcode [!] = <number{0-15}]>
[icmpcodeend = <number{0-15}]>
where:
name
type
The name of an expression to add.
The type of an expression.
REQUIRED
OPTIONAL
REQUIRED
mac [!]
The MAC address.
If a value is preceded by a
addr [!]
The IP address or range.
If a value is preceded by a
REQUIRED
mask [
intf [!]
The IP mask (ignored if an IP range is provided).
OPTIONAL
OPTIONAL
The IP interface name.
If a value is preceded by a
intfgroup [!]
tos [!]
The IP interface group.
OPTIONAL
OPTIONAL
If a value is preceded by a
The Type Of Service specification in the IP
packet.
If a value is preceded by a
E-DOC-CTC-20071119-0014 v1.0
333
Download from Www.Somanuals.com. All Manuals Search And Download.
expr Commands
precedence [!]
dscp [!]
The precedence in the IP packet (part of tos).
OPTIONAL
OPTIONAL
If a value is preceded by a
The diffserv code point in the IP packet (part of
tos).
If a value is preceded by a
proto [!]
The IP protocol (name or number) in the IP
packet.
OPTIONAL
OPTIONAL
If a value is preceded by a
srcport [!]
The TCP/UDP source port number or range
begin.
If a value is preceded by a
srcportend
dstport [!]
The source TCP/UDP source port range end.
(inclusive)
OPTIONAL
OPTIONAL
The TCP/UDP destination port number or range
begin.
If a value is preceded by a
dstportend
The TCP/UDP destination port range end.
OPTIONAL
OPTIONAL
icmptype [!]
The ICMP type (name or number) of the packet.
If a value is preceded by a
icmpcode [!]
icmpcodeend
The ICMP code or range begin.
If a value is preceded by a
OPTIONAL
OPTIONAL
The ICMP code range end. (inclusive)
E-DOC-CTC-20071119-0014 v1.0
334
Download from Www.Somanuals.com. All Manuals Search And Download.
expr Commands
expr delete
Delete an expression.
SYNTAX:
expr delete
name = <{wan|local|lan|tunnel|dmz|guest|
private|ssdp_ip|mdap_ip|icmp|igmp|imaps|pop2|
pop3|pop3s|smtp|ssh|dns|nntp|ipsec|esp|ah|
ike|DiffServ|sip|h323|dhcp|rtsp|ssdp_serv|
mdap_serv|syslog}>
[index = <number]>
where:
name
index
The name of an expression to delete.
The index of a subexpression.
REQUIRED
OPTIONAL
E-DOC-CTC-20071119-0014 v1.0
335
Download from Www.Somanuals.com. All Manuals Search And Download.
expr Commands
expr list
List expressions.
SYNTAX:
expr list
[name = <{_intf_0|_intf_1|_intf_2|DHCP-
R_if_0|wan|local|lan|tunnel|dmz|TELNET_if_0|
DNS-S_if_0|PING_RESPONDER_if_0|MDAP_if_0|
PPTPD_if_0|PPTPGRE_if_0|_addr_127_0_0_1|
_addr_10_0_0_138|_addr_192_168_1_254|private|
ssdp_ip|mdap_ip|DHCP-R_sv_0|icmp|igmp|ftp|
telnet|http|httpproxy|https|RPC|NBT|SMB|imap|
imap3|imap4-ssl|imaps|pop2|pop3|pop3s|smtp|
ssh|dns|nntp|ipsec|esp|ah|ike|DiffServ|sip|
h323|dhcp|rtsp|ssdp_serv|mdap_serv|syslog|
HTTPI_sv_0|SSDP_sv_0}]>
[type = <{intf|ip|serv|mac}]>
[format = <{pretty|cli}]>
where:
name
type
The name of an expression to list.
The type of an expression.
OPTIONAL
OPTIONAL
OPTIONAL
format
The format of the expression list.
E-DOC-CTC-20071119-0014 v1.0
337
Download from Www.Somanuals.com. All Manuals Search And Download.
expr Commands
expr modify
Modify an expression.
SYNTAX:
expr modify
name = <{wan|local|lan|tunnel|dmz|guest|
private|ssdp_ip|mdap_ip|icmp|igmp|imaps|pop2|
pop3|pop3s|smtp|ssh|dns|nntp|ipsec|esp|ah|
ike|DiffServ|sip|h323|dhcp|rtsp|ssdp_serv|
mdap_serv|syslog}>
[type = <{intf|ip|serv|mac}]>
index = <number>
mac [!] = <hardware-address>
addr [!] = <ip-range>
[mask [ = <ip-mask(dotted or cidr)]>
[intf [!] = <{loop|Internet|LocalNetwork}]>
[intfgroup [!] = <{wan|local|lan|tunnel|dmz|
guest} or number]>
[tos [!] = <number{0-255}]>
[precedence [!] = <{routine|priority|
immediate|flash|flash-override|CRITIC-ECP|
internetwork-control|network-control} or
number]>
[dscp [!] = <{ef|af11|af12|af13|af21|af22|
af23|af31|af32|af33|af41|af42|af43|cs0|cs1|
cs2|cs3|cs4|cs5|cs6|cs7} or number]>
[proto [!] = <{icmp|igmp|ipinip|tcp|udp|ah|
esp|ipcomp} or number]>
[srcport [!] = <{at-echo|at-nbp|at-rtmp|at-
zis|auth|bgp|biff|bootpc|bootps|finger|ftp|
ftp-data|gopher|h323|httpproxy|ike|ils|imap2|
imap3|ingres-net|ipcserver|ipx|irc-o|irc-u|
kerberos|ldap|login|netbios-dgm|netbios-ns|
netbios-ssn|netwall|netware-ip|new-rwho|nfds|
nicname|nntp|ntalk|ntp|pcmail-srv|pop2|pop3|
printer|qotd|realaudio|rip|rtelnet|rtsp|sip|
smtp|snmp|snmptrap|snpp|sntp|sql*net|sql-
net|sqlserv|sunrpc|syslog|systat|talk|...}or
number]>
[srcportend = <{at-echo|at-nbp|at-rtmp|at-
zis|auth|bgp|biff|bootpc|bootps|finger|ftp|
ftp-data|gopher|h323|httpproxy|ike|ils|imap2|
imap3|ingres-net|ipcserver|ipx|irc-o|irc-u|
kerberos|ldap|login|netbios-dgm|netbios-ns|
netbios-ssn|netwall|netware-ip|new-rwho|nfds|
nicname|nntp|ntalk|ntp|pcmail-srv|pop2|pop3|
printer|qotd|realaudio|rip|rtelnet|rtsp|sip|
smtp|snmp|snmptrap|snpp|sntp|sql*net|sql-
net|sqlserv|sunrpc|syslog|systat|talk|...}or
number]>
E-DOC-CTC-20071119-0014 v1.0
338
Download from Www.Somanuals.com. All Manuals Search And Download.
expr Commands
[dstport [!] = <{at-echo|at-nbp|at-rtmp|at-
zis|auth|bgp|biff|bootpc|bootps|finger|ftp|
ftp-data|gopher|h323|httpproxy|ike|ils|imap2|
imap3|ingres-net|ipcserver|ipx|irc-o|irc-u|
kerberos|ldap|login|netbios-dgm|netbios-ns|
netbios-ssn|netwall|netware-ip|new-rwho|nfds|
nicname|nntp|ntalk|ntp|pcmail-srv|pop2|pop3|
printer|qotd|realaudio|rip|rtelnet|rtsp|sip|
smtp|snmp|snmptrap|snpp|sntp|sql*net|sql-
net|sqlserv|sunrpc|syslog|systat|talk|...}or
number]>
[dstportend = <{at-echo|at-nbp|at-rtmp|at-
zis|auth|bgp|biff|bootpc|bootps|finger|ftp|
ftp-data|gopher|h323|httpproxy|ike|ils|imap2|
imap3|ingres-net|ipcserver|ipx|irc-o|irc-u|
kerberos|ldap|login|netbios-dgm|netbios-ns|
netbios-ssn|netwall|netware-ip|new-rwho|nfds|
nicname|nntp|ntalk|ntp|pcmail-srv|pop2|pop3|
printer|qotd|realaudio|rip|rtelnet|rtsp|sip|
smtp|snmp|snmptrap|snpp|sntp|sql*net|sql-
net|sqlserv|sunrpc|syslog|systat|talk|...}or
number]>
[icmptype [!] = <{echo-reply|destination-
unreachable|source-quench|redirect|exceeded|
parameter-problems|timestamp-request|
timestamp-reply|information-request|
information-reply|address-mask-request|
address-mask-reply} or number]>
[icmpcode [!] = <number{0-15}]>
[icmpcodeend = <number{0-15}]>
where:
name
type
The name of an expression to modify.
The type of an expression.
REQUIRED
OPTIONAL
REQUIRED
REQUIRED
index
mac [!]
The index of a subexpression.
The MAC address.
If a value is preceded by a
addr [!]
The IP address or range.
If a value is preceded by a
REQUIRED
mask [
intf [!]
The IP mask (ignored if an IP range is provided).
OPTIONAL
OPTIONAL
The IP interface name.
If a value is preceded by a
intfgroup [!]
The IP interface group.
OPTIONAL
If a value is preceded by a
E-DOC-CTC-20071119-0014 v1.0
339
Download from Www.Somanuals.com. All Manuals Search And Download.
expr Commands
tos [!]
The Type Of Service specification in the IP
packet.
OPTIONAL
If a value is preceded by a
precedence [!]
dscp [!]
The precedence in the IP packet (part of tos).
If a value is preceded by a
OPTIONAL
OPTIONAL
The diffserv code point in the IP packet (part of
tos).
If a value is preceded by a
proto [!]
The IP protocol (name or number) in the IP
packet.
OPTIONAL
OPTIONAL
If a value is preceded by a
srcport [!]
The TCP/UDP source port number or range
begin.
If a value is preceded by a
srcportend
dstport [!]
The source TCP/UDP source port range end.
(inclusive)
OPTIONAL
OPTIONAL
The TCP/UDP destination port number or range
begin.
If a value is preceded by a
dstportend
The TCP/UDP destination port range end.
OPTIONAL
OPTIONAL
icmptype [!]
The ICMP type (name or number) of the packet.
If a value is preceded by a
icmpcode [!]
icmpcodeend
The ICMP code or range begin.
If a value is preceded by a
OPTIONAL
OPTIONAL
The ICMP code range end. (inclusive)
E-DOC-CTC-20071119-0014 v1.0
340
Download from Www.Somanuals.com. All Manuals Search And Download.
firewall Commands
firewall config
Display/Modify firewall configuration.
SYNTAX:
firewall config
[state = <{disabled|enabled}]>
[keep = <{disabled|enabled}]>
[tcpchecks = <{none|fast|exact}]>
[udpchecks = <{disabled|enabled}]>
[icmpchecks = <{disabled|enabled}]>
[logdefault = <{disabled|enabled}]>
[logthreshold = <{disabled|enabled}]>
[tcpwindow = <number{0-1073725440}]>
where:
state
keep
Disable/Enable the firewall.
OPTIONAL
OPTIONAL
Disable/Enable keeping existing connections
when firewall rules change.
tcpchecks
Select level of TCP checks.
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
udpchecks
icmpchecks
logdefault
logthreshold
tcpwindow
Disable/Enable UDP checks.
Disable/Enable ICMP checks.
Disable/Enable logging of default firewall rule.
Disable/Enable log thresholding.
Modify the tcpwindow for fast TCP checks
E-DOC-CTC-20071119-0014 v1.0
347
Download from Www.Somanuals.com. All Manuals Search And Download.
firewall Commands
firewall level add
Add a new security level.
SYNTAX:
firewall level add
name = <string>
[index = <number]>
[readonly = <{disabled|enabled}]>
[udptrackmode = <{strict|loose}]>
[service = <{disabled|enabled}]>
[proxy = <{disabled|enabled}]>
[text = <quoted string]>
[policy = <{default|drop|accept}]>
where:
name
The name of the security level to add.
The index of the security level.
REQUIRED
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
index
readonly
udptrackmode
service
Select whether the security level is readonly.
Select UDP connection tracking mode.
Enable/Disable host service definitions for this
security level.
proxy
Enable/Disable proxy system services for this
security level.
OPTIONAL
text
The description of this security level.
OPTIONAL
OPTIONAL
policy
Select default policy of this security level.
E-DOC-CTC-20071119-0014 v1.0
350
Download from Www.Somanuals.com. All Manuals Search And Download.
firewall Commands
firewall level modify
Modify a security level.
SYNTAX:
firewall level modify
name = <security level name>
[index = <number]>
[readonly = <{disabled|enabled}]>
[udptrackmode = <{strict|loose}]>
[service = <{disabled|enabled}]>
[proxy = <{disabled|enabled}]>
[text = <quoted string]>
[policy = <{default|drop|accept}]>
where:
name
The name of the security level to modify.
The index of this security level.
REQUIRED
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
index
readonly
udptrackmode
service
Select whether the security level is readonly.
Select UDP connection tracking mode.
Enable/Disable service definitions for this
security level.
proxy
Enable/Disable proxy system services for this
security level.
OPTIONAL
text
The description of this security level.
OPTIONAL
OPTIONAL
policy
Select default policy of this security level.
E-DOC-CTC-20071119-0014 v1.0
354
Download from Www.Somanuals.com. All Manuals Search And Download.
firewall Commands
firewall rule add
Add a rule.
SYNTAX:
firewall rule add
chain = <chain name>
[index = <number]>
[name = <string]>
[clink = <chain name]>
[srcintf [!] = <{wan|local|lan|tunnel|dmz|
guest}]>
[srcip [!] = <{private|ssdp_ip|mdap_ip}]>
[dstintf [!] = <{wan|local|lan|tunnel|dmz|
guest}]>
[dstip [!] = <{private|ssdp_ip|mdap_ip}]>
[serv [!] = <{icmp|igmp|ftp|telnet|http|
httpproxy|https|RPC|NBT|SMB|imap|esp|ah|
ike|DiffServ|sip|h323|dhcp|rtsp|ssdp_serv|
mdap_serv|syslog}]>
[log = <{disabled|enabled}]>
[state = <{disabled|enabled}]>
action = <{accept|deny|drop|reset|count|link}>
where:
chain
index
name
clink
The name of the chain which contains the rule.
The index of the rule in the chain.
The name of the new rule.
REQUIRED
OPTIONAL
OPTIONAL
OPTIONAL
The name of the chain to be parsed when this
rule applies.
srcintf [!]
srcip [!]
The name of the source interface expression.
If a value is preceded by a
OPTIONAL
OPTIONAL
OPTIONAL
The name of the source ip expression.
If a value is preceded by a
dstintf [!]
The name of the destination interface
expression.
If a value is preceded by a
dstip [!]
serv [!]
The name of the destination ip expression.
If a value is preceded by a
OPTIONAL
OPTIONAL
The name of the service expression.
If a value is preceded by a
E-DOC-CTC-20071119-0014 v1.0
357
Download from Www.Somanuals.com. All Manuals Search And Download.
firewall Commands
log
Disable/Enable logging when this rule applies.
OPTIONAL
OPTIONAL
REQUIRED
state
action
Disable/Enable this rule.
The action to be taken when this rule applies
('link' when clink is used).
E-DOC-CTC-20071119-0014 v1.0
358
Download from Www.Somanuals.com. All Manuals Search And Download.
firewall Commands
firewall rule delete
Delete a rule.
SYNTAX:
firewall rule delete
chain = <chain name>
index = <number>
where:
chain
The name of the chain in which to delete the
rule.
REQUIRED
REQUIRED
index
The number of the rule in the chain.
E-DOC-CTC-20071119-0014 v1.0
359
Download from Www.Somanuals.com. All Manuals Search And Download.
firewall Commands
firewall rule list
Display a list of rules.
SYNTAX:
firewall rule list
[chain = <chain name]>
[format = <{pretty|cli}]>
where:
chain
The name of the chain to list the rules of.
The format of the rule list.
OPTIONAL
OPTIONAL
format
E-DOC-CTC-20071119-0014 v1.0
361
Download from Www.Somanuals.com. All Manuals Search And Download.
firewall Commands
firewall rule modify
Modify a rule.
SYNTAX:
firewall rule modify
chain = <chain name>
[index = <number]>
[newindex = <number]>
[name = <string]>
[clink = <chain name]>
[[!]srcintf] = <chain name]>
[[!]srcip] = <chain name]>
[[!]dstintf] = <chain name]>
[[!]dstip] = <chain name]>
[[!]serv] = <chain name]>
[log = <{disabled|enabled}]>
[state = <{disabled|enabled}]>
[action = <{accept|deny|drop|reset|count|
link}]>
where:
chain
The name of the chain which contains the rule.
The index of the rule in the chain.
The new index of the rule in the chain.
The name of the new rule.
REQUIRED
index
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
newindex
name
clink
The name of the chain to be parsed when this
rule applies.
[!]srcintf]
[!]srcip]
The name of the source interface expression.
If a value is preceded by a
OPTIONAL
OPTIONAL
OPTIONAL
The name of the source ip expression.
If a value is preceded by a
[!]dstintf]
The name of the destination interface
expression.
If a value is preceded by a
[!]dstip]
[!]serv]
log
The name of the destination ip expression.
If a value is preceded by a
OPTIONAL
OPTIONAL
OPTIONAL
The name of the service expression.
If a value is preceded by a
Disable/Enable logging when this rule applies.
E-DOC-CTC-20071119-0014 v1.0
362
Download from Www.Somanuals.com. All Manuals Search And Download.
firewall Commands
state
Disable/Enable this rule.
OPTIONAL
OPTIONAL
action
The action to be taken when this rule applies
('link' when clink is used).
E-DOC-CTC-20071119-0014 v1.0
363
Download from Www.Somanuals.com. All Manuals Search And Download.
grp Commands
E-DOC-CTC-20071119-0014 v1.0
364
Download from Www.Somanuals.com. All Manuals Search And Download.
grp Commands
grp config
Set the grp configuration settings.
SYNTAX:
grp config
[cdistance = <number{0-255}]>
[kdistance = <number{0-255}]>
[rdistance = <number{0-255}]>
[trace = <{disabled|enabled}]>
where:
cdistance
Set the distance of the connected route type.
Default distance is 0.
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
kdistance
rdistance
trace
Set the distance of the kernel route type. Default
distance is 1.
Set the distance of the RIP route type. Default
distance is 120.
Enable/Disable tracing.
E-DOC-CTC-20071119-0014 v1.0
366
Download from Www.Somanuals.com. All Manuals Search And Download.
grp Commands
grp rip config
Set the RIP configuration settings.
SYNTAX:
grp rip config
state = <{disabled|enabled}>
[version = <{rip_unspec|rip_v1|rip_v2}]>
[updatetime = <number{1-3600}]>
where:
state
Enable/Disable the RIP daemon.
Set the RIP version.
REQUIRED
version
updatetime
OPTIONAL
OPTIONAL
Set the routing table update timer value. Default
is 30 seconds.
E-DOC-CTC-20071119-0014 v1.0
368
Download from Www.Somanuals.com. All Manuals Search And Download.
grp Commands
grp rip ifconfig
Configure a RIP interface.
SYNTAX:
grp rip ifconfig
intf = <{LocalNetwork|Internet}>
[rip = <{disabled|enabled}]>
[rxversion = <{rip_unspec|rip_v1|rip_v2|
rip_v1-2}]>
[authmode = <{none|cleartext}]>
[authstr = <password]>
[splithorizon = <{disabled|enabled}]>
where:
intf
The name of the RIP interface to configure.
Enable/Disable the RIP status.
REQUIRED
rip
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
rxversion
authmode
authstr
splithorizon
Set the RIP receive version.
Set the RIP authentication mode.
Set the RIP authentication password.
Enable/Disable the split horizon status.
E-DOC-CTC-20071119-0014 v1.0
370
Download from Www.Somanuals.com. All Manuals Search And Download.
grp Commands
grp rtlist
Show the current routes in the grp routing table.
SYNTAX:
grp rtlist
[dst = <ip-address]>
[dstmsk = <ip-mask(dotted or cidr)]>
where:
dst
The destination IP address using this route.
Supports ip/mask notation.
OPTIONAL
OPTIONAL
dstmsk
The destination IP address mask.
E-DOC-CTC-20071119-0014 v1.0
372
Download from Www.Somanuals.com. All Manuals Search And Download.
hostmgr Commands
E-DOC-CTC-20071119-0014 v1.0
374
Download from Www.Somanuals.com. All Manuals Search And Download.
hostmgr Commands
hostmgr add
Add host device info to hostmgr
SYNTAX:
hostmgr add
mac_addr = <hardware-address>
[ip_addr = <ip-address]>
[name = <string]>
[type = <{generic_device|desktop_computer|
laptop_computer|set_top_box|pda|
gaming_console|phone|mobile_phone|printer|
mass_storage_device}]>
[ipintf = <{loop|Internet|LocalNetwork}]>
[ethintf = <{bridge|RELAY|ethoa_8_35}]>
[physintf = <{ethif1|ethif2|ethif3|ethif4|
wlif1}]>
where:
mac_addr
ip_addr
name
Host MAC address
REQUIRED
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
Host IP address
host name
type
host type
ipintf
IP interface name.
Ethernet interface name.
Physical interface name.
ethintf
physintf
E-DOC-CTC-20071119-0014 v1.0
376
Download from Www.Somanuals.com. All Manuals Search And Download.
hostmgr Commands
hostmgr config
Config hostmgr parameters
SYNTAX:
hostmgr config
[state = <{disabled|enabled}]>
[scantime = <number{10-600}]>
[autosave = <{disabled|enabled}]>
[trace = <{disabled|enabled}]>
where:
state
Enable/disable hostmgr deamon
Time between two scans (sec)
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
scantime
autosave
trace
Enable/disable automatic saves to flash
Enable/disable hostmgr traces
E-DOC-CTC-20071119-0014 v1.0
378
Download from Www.Somanuals.com. All Manuals Search And Download.
ids Commands
E-DOC-CTC-20071119-0014 v1.0
382
Download from Www.Somanuals.com. All Manuals Search And Download.
ids Commands
ids parser modify
Modify ids parser configuration.
SYNTAX:
ids parser modify
[parser = <parser]>
state = <{disabled|enabled}>
where:
parser
state
The name of the parser.
The state of the parser.
OPTIONAL
REQUIRED
E-DOC-CTC-20071119-0014 v1.0
387
Download from Www.Somanuals.com. All Manuals Search And Download.
ids Commands
ids signature list
Display ids signature configuration.
SYNTAX:
ids signature list
[signature = <fragment_sweep|zero-
length_fragment_size|small_fragment_size|
ip_protocol_scan|tcp_port_scan|
tcp_syn_scan|stealth_tcp_null_scan|
stealth_tcp_fin_scan|stealth_tcp_xmas_scan|
stealth_tcp_full_xmas_scan|
stealth_tcp_vecna_scan|stealth_tcp_syn-
fin_scan|udp_port_scan|ping_sweep_scan|
tcp_syn_flood|udp_flood|ping_flood|
icmp_unreachable_storm|smurf_broadcast_attack|
smurf_storm_attack|fraggle_broadcast_attack|
fraggle_storm_attack|land_attack}]>
where:
signature
The name of the signature.
OPTIONAL
E-DOC-CTC-20071119-0014 v1.0
391
Download from Www.Somanuals.com. All Manuals Search And Download.
ids Commands
ids signature modify
Modify ids signature configuration.
SYNTAX:
ids signature modify
[signature = <fragment_sweep|zero-
length_fragment_size|small_fragment_size|
ip_protocol_scan|tcp_port_scan|
tcp_syn_scan|stealth_tcp_null_scan|
stealth_tcp_fin_scan|stealth_tcp_xmas_scan|
stealth_tcp_full_xmas_scan|
stealth_tcp_vecna_scan|stealth_tcp_syn-
fin_scan|udp_port_scan|ping_sweep_scan|
tcp_syn_flood|udp_flood|ping_flood|
icmp_unreachable_storm|smurf_broadcast_attack|
smurf_storm_attack|fraggle_broadcast_attack|
fraggle_storm_attack|land_attack}]>
state = <{disabled|enabled}>
where:
signature
state
The name of the signature.
The state of the sign.
OPTIONAL
REQUIRED
E-DOC-CTC-20071119-0014 v1.0
392
Download from Www.Somanuals.com. All Manuals Search And Download.
ids Commands
ids threshold modify
Modify IDS threshold.
SYNTAX:
ids threshold modify
index = <number>
[window = <number]>
[limit = <number]>
[scaling = <{disabled|enabled}]>
where:
index
The index of the threshold.
REQUIRED
OPTIONAL
OPTIONAL
OPTIONAL
window
limit
The time window of the threshold.
The limit of the threshold.
scaling
Scaling of the threshold window.
E-DOC-CTC-20071119-0014 v1.0
395
Download from Www.Somanuals.com. All Manuals Search And Download.
igmp Commands
E-DOC-CTC-20071119-0014 v1.0
396
Download from Www.Somanuals.com. All Manuals Search And Download.
igmp Commands
igmp host config
Display/Modify global IGMP configuration.
SYNTAX:
igmp host config
where:
[requirera = <{disabled|enabled}]>
requirera
Enable/Disable the router alert IP option check.
OPTIONAL
E-DOC-CTC-20071119-0014 v1.0
398
Download from Www.Somanuals.com. All Manuals Search And Download.
igmp Commands
igmp host ifconfig
Configure an IGMP interface.
SYNTAX:
igmp host ifconfig
intf = <{loop|Internet|LocalNetwork}>
version = <{none|IGMPv1|IGMPv2|IGMPv3}>
where:
intf
The IP interface name.
REQUIRED
version
The IGMP version of the IP interface.
REQUIRED
E-DOC-CTC-20071119-0014 v1.0
402
Download from Www.Somanuals.com. All Manuals Search And Download.
igmp Commands
igmp host list
Show the IGMP groups.
SYNTAX:
igmp host list
[intf = <{loop|Internet|LocalNetwork}]>
[expand = <{disabled|enabled}]>
where:
intf
The IP interface name.
Expanded listing.
OPTIONAL
OPTIONAL
expand
E-DOC-CTC-20071119-0014 v1.0
404
Download from Www.Somanuals.com. All Manuals Search And Download.
igmp Commands
igmp proxy config
Configure the IGMP proxy.
SYNTAX:
igmp proxy config
[state = <{disabled|enabled}]>
[qi = <number{1-86400}]>
[qri = <number{1-86400}]>
[lmqi = <number{1-86400}]>
[rv = <number{2-10}]>
[advinter = <number{4-180}]>
[initadvinter = <number{1-4}]>
[initadvcount = <number{1-10}]>
[requirera = <{disabled|enabled}]>
[localgroup = <{disabled|enabled}]>
where:
state
qi
Enable/Disable the IGMP proxy.
OPTIONAL
The interval in seconds between general queries OPTIONAL
sent by the querier.
qri
The maximum response time in seconds for an
IGMP client in reply to general queries.
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
lmqi
The maximum response time in seconds for an
IGMP client in reply to group specific queries.
rv
The robustness variable allows tuning for
expected IGMP packet loss.
advinter
initadvinter
initadvcount
The interval in seconds for unsolicited MRD
advertisements (see rfc4286).
The interval in seconds for initial unsolicited
MRD advertisements (see rfc4286).
The maximum number of initial unsolicited MRD OPTIONAL
advertisements (see rfc4286).
requirera
Enable/Disable the router alert IP option check.
OPTIONAL
OPTIONAL
localgroup
Enable/Disable the processing of a local
multicast group in an IGMP packet.
E-DOC-CTC-20071119-0014 v1.0
405
Download from Www.Somanuals.com. All Manuals Search And Download.
igmp Commands
igmp proxy grouplist
Show the learned groups on an IGMP proxy interface.
SYNTAX:
igmp proxy grouplist
[intf = <{LocalNetwork}]>
[expand = <{disabled|enabled}]>
where:
intf
The name of the IGMP proxy interface to be
listed.
OPTIONAL
OPTIONAL
expand
Expanded listing.
E-DOC-CTC-20071119-0014 v1.0
410
Download from Www.Somanuals.com. All Manuals Search And Download.
igmp Commands
igmp proxy ifconfig
Configure an IGMP proxy interface.
SYNTAX:
igmp proxy ifconfig
intf = <{LocalNetwork|Internet}>
[state = <{inactive|downstream|upstream}]>
[version = <{IGMPv1|IGMPv2|IGMPv3}]>
[fastleave = <{disabled|enabled}]>
[exptrack = <{disabled|enabled}]>
[mrd = <{disabled|enabled}]>
where:
intf
The name of the IGMP proxy interface to be
configured.
REQUIRED
state
The state of the IGMP proxy interface.
OPTIONAL
OPTIONAL
OPTIONAL
version
fastleave
The IGMP version of the IGMP proxy interface.
Enable/Disable the immediate deletion of a
group when a leave is received.
exptrack
mrd
Enable/Disable explicit host tracking.
OPTIONAL
OPTIONAL
Enable/Disable sending multicast router
advertisements (rfc 4286).
E-DOC-CTC-20071119-0014 v1.0
411
Download from Www.Somanuals.com. All Manuals Search And Download.
interface Command
E-DOC-CTC-20071119-0014 v1.0
414
Download from Www.Somanuals.com. All Manuals Search And Download.
interface Command
interface Command
Display interfaces.
SYNTAX:
interface list
[expand = <{disabled|enabled}]>
[reverse = <{disabled|enabled}]>
where:
expand
reverse
Expanded listing.
Reverse listing (lower layer iso. upper layer).
OPTIONAL
OPTIONAL
E-DOC-CTC-20071119-0014 v1.0
415
Download from Www.Somanuals.com. All Manuals Search And Download.
ip Commands
E-DOC-CTC-20071119-0014 v1.0
416
Download from Www.Somanuals.com. All Manuals Search And Download.
ip Commands
E-DOC-CTC-20071119-0014 v1.0
418
Download from Www.Somanuals.com. All Manuals Search And Download.
ip Commands
ip arpadd
Add an entry to the ARP cache of a broadcast IP interface.
SYNTAX:
ip arpadd
intf = <{LocalNetwork}>
ip = <ip-range>
[hwaddr = <hardware-address]>
where:
intf
The IP interface name.
REQUIRED
REQUIRED
OPTIONAL
ip
The IP address [range] of the entry to add.
hwaddr
The hardware address (e.g. Ethernet MAC
address) of the entry to add.
E-DOC-CTC-20071119-0014 v1.0
419
Download from Www.Somanuals.com. All Manuals Search And Download.
ip Commands
ip arpdelete
Delete an ARP entry.
SYNTAX:
ip arpdelete
intf = <{LocalNetwork}>
ip = <ip-range>
[hwaddr = <hardware-address]>
where:
intf
The IP interface name.
REQUIRED
REQUIRED
OPTIONAL
ip
The IP address [range] of the entry to delete.
hwaddr
The hardware address (e.g. Ethernet MAC
address) of the entry to delete.
E-DOC-CTC-20071119-0014 v1.0
420
Download from Www.Somanuals.com. All Manuals Search And Download.
ip Commands
ip auto ifadd
Creates a new autoIP interface.
SYNTAX:
ip auto ifadd
intf = <{loop|Internet|LocalNetwork}>
[addr = <ip-address]>
where:
intf
The name of the IP interface for which a link-
local address has to be allocated.
REQUIRED
OPTIONAL
addr
The preferred link-local IP address.
E-DOC-CTC-20071119-0014 v1.0
423
Download from Www.Somanuals.com. All Manuals Search And Download.
ip Commands
ip auto ifconfig
Configures an autoIP interface.
SYNTAX:
ip auto ifconfig
intf = <>
[addr = <ip-address]>
[poolstart = <ip-address]>
[poolend = <ip-address]>
[netmask = <ip-mask(dotted or cidr)]>
[claim = <number{0-65535}]>
[defence = <number{0-65535}]>
[probe = <number{0-65535}]>
[interval = <number{1-65535}]>
where:
intf
The name of the autoIP interface to configure.
The preferred link-local IP address.
REQUIRED
OPTIONAL
OPTIONAL
addr
poolstart
The start IP address of the link-local address
pool.
poolend
netmask
claim
The end IP address of the link-local address pool. OPTIONAL
The netmask of the link-local IP address pool.
OPTIONAL
OPTIONAL
The number of link-local address selection
retries before giving up.
defence
probe
The number of times the link-local address is
defended before releasing the address.
OPTIONAL
OPTIONAL
OPTIONAL
The number of ARP probes to be sent before
accepting a link-local address.
interval
The time interval between two ARP probe
transmissions.
E-DOC-CTC-20071119-0014 v1.0
425
Download from Www.Somanuals.com. All Manuals Search And Download.
ip Commands
ip config
Display/Modify global IP stack configuration.
SYNTAX:
ip config
[forwarding = <{disabled|enabled}]>
[redirects = <{disabled|enabled}]>
[checkoptions = <{disabled|enabled|
transparent}]>
[netbroadcasts = <{disabled|enabled}]>
[ttl = <number{0-255}]>
[fraglimit = <number{1-1024}]>
[defragmode = <{disabled|enabled}]>
[addrcheck = <{off|own|static|dynamic}]>
[mssclamping = <{disabled|enabled}]>
[natloopback = <{disabled|enabled}]>
where:
forwarding
redirects
Disable/Enable IP routing functionality.
OPTIONAL
Disable/Enable sending of ICMP redirect
messages.
OPTIONAL
checkoptions
netbroadcasts
ttl
Disallow/Allow packets with IP options.
Disallow/Allow net directed broadcasts.
OPTIONAL
OPTIONAL
OPTIONAL
Set the default time-to-live for locally generated
IP packets.
fraglimit
Set the maximum number of IP fragments
waiting for completion. (Avoids buffer
depletion).
OPTIONAL
defragmode
addrcheck
Disallow/Allow defragmenting IP fragments.
Sets the level of ip address checks.
OPTIONAL
OPTIONAL
OPTIONAL
mssclamping
Disable/Enable mss clamping for low mtu
interfaces.
natloopback
Disable/Enable NAT loopback.
OPTIONAL
E-DOC-CTC-20071119-0014 v1.0
429
Download from Www.Somanuals.com. All Manuals Search And Download.
ip Commands
ip debug httpprobe
Send HTTP probe to measure the round trip time taken to connect and access
SYNTAX:
ip debug httpprobe
url = <string>
[version = <{1.0|1.1}]>
where:
url
The Uniform Resource location identifying the
HTTP server.
REQUIRED
OPTIONAL
version
The version of the HTTP Server.
E-DOC-CTC-20071119-0014 v1.0
430
Download from Www.Somanuals.com. All Manuals Search And Download.
ip Commands
ip debug sendto
Send UDP packets.
SYNTAX:
ip debug sendto
addr = <ip-address>
[count = <number{1-1000000}]>
[size = <number{0-20000}]>
[interval = <number{1-1000000}]>
[listen = <{disabled|enabled}]>
[dffield = <{disabled|enabled}]>
[srcaddr = <ip-address]>
[srcport = <number{1-65535}]>
dstport = <number{1-65535}>
[dstintf = <{loop|Internet|LocalNetwork}]>
where:
addr
The destination IP address.
The number of datagrams to send.
The size of the datagram.
REQUIRED
count
size
OPTIONAL
OPTIONAL
interval
listen
dffield
The interval in milliseconds between datagrams. OPTIONAL
Don't send, just listen for incoming datagrams.
OPTIONAL
OPTIONAL
Enables setting of the don't fragment flag in the
IP headers of the ping packet(s).
srcaddr
srcport
dstport
dstintf
The IP source address to use.
OPTIONAL
OPTIONAL
REQUIRED
OPTIONAL
The UDP source port number to use.
The UDP destination port number to send to.
The IP interface name.
E-DOC-CTC-20071119-0014 v1.0
431
Download from Www.Somanuals.com. All Manuals Search And Download.
ip Commands
ip debug traceconfig
Display/Modify IP stack trace configuration.
SYNTAX:
ip debug traceconfig
[input = <{none|label|-telnet|-host|-
broadcast|all}]>
[forward = <{none|label|-telnet|-host|-
broadcast|all}]>
[output = <{none|label|-telnet|-host|-
broadcast|all}]>
[drop = <{none|label|-telnet|-host|-broadcast|
all}]>
[path = <{none|label|-telnet|-host|-broadcast|
all}]>
[mode = <{line|dump}]>
[arp = <{none|all}]>
where:
input
forward
output
drop
Define the packets that will be traced.
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
Define the packets that will be traced.
Define the packets that will be traced.
Define the packet drops that will be traced.
Define the packet that will be path-traced.
Packet dump method.
path
mode
arp
Define the arp packets that will be traced.
E-DOC-CTC-20071119-0014 v1.0
433
Download from Www.Somanuals.com. All Manuals Search And Download.
ip Commands
ip ifconfig
Modify an IP interface configuration.
SYNTAX:
ip ifconfig
intf = <{loop|Internet|LocalNetwork}>
[mtu = <number{68-65535}]>
[status = <{down|up}]>
[hwaddr = <hardware-address]>
[group = <{wan|local|lan|tunnel|dmz|guest} or
number]>
[linksensing = <{disabled|enabled}]>
[primary = <{disabled|enabled}]>
[mcastpromisc = <{disabled|enabled}]>
where:
intf
An IP interface name.
REQUIRED
OPTIONAL
mtu
The maximum packet size (including IP header)
to use on this interface.
status
The administrative state of the interface.
OPTIONAL
OPTIONAL
hwaddr
The hardware address (e.g. Ethernet MAC
address) of this interface.
group
The group this interface belongs to. Can be used OPTIONAL
by e.g. firewalling.
linksensing
The IP interface's awareness of link state
transitions.
OPTIONAL
primary
Make the IP interface the primary interface.
Make the IP interface multicast promiscuous.
OPTIONAL
OPTIONAL
mcastpromisc
E-DOC-CTC-20071119-0014 v1.0
437
Download from Www.Somanuals.com. All Manuals Search And Download.
ip Commands
ip ifwait
Wait for a status change of an IP interface.
SYNTAX:
ip ifwait
intf = <{loop|Internet|LocalNetwork}>
[timeout = <number{1-600000}]>
[adminstatus = <{down|up}]>
[operstatus = <{down|up}]>
[linkstatus = <{down|up}]>
where:
intf
An IP interface name.
REQUIRED
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
timeout
The timeout in seconds.
adminstatus
operstatus
linkstatus
The administrative state of the interface.
The operational state of the interface.
The link state of the interface.
E-DOC-CTC-20071119-0014 v1.0
441
Download from Www.Somanuals.com. All Manuals Search And Download.
ip Commands
ip ipadd
Assign an IP address to an IP interface.
SYNTAX:
ip ipadd
intf = <{loop|Internet|LocalNetwork}>
addr = <ip-address>
[netmask = <ip-mask(dotted or cidr)]>
[pointopoint = <ip-address]>
[addroute = <{disabled|enabled}]>
where:
intf
The IP interface name.
REQUIRED
REQUIRED
OPTIONAL
OPTIONAL
addr
The new IP address to add.
netmask
pointopoint
The subnetmask associated with this address.
The remote address in case of a point-to-point
link.
addroute
Add typical net/subnet routes automatically.
OPTIONAL
E-DOC-CTC-20071119-0014 v1.0
442
Download from Www.Somanuals.com. All Manuals Search And Download.
ip Commands
ip ipconfig
Modify an IP address configuration.
SYNTAX:
ip ipconfig
addr = <ip-address>
[preferred = <{disabled|enabled}]>
[primary = <{disabled|enabled}]>
where:
addr
The IP address to configure.
REQUIRED
OPTIONAL
preferred
Make IP address the preferred address for that
subnet.
primary
Make IP address the primary address for the
interface.
OPTIONAL
E-DOC-CTC-20071119-0014 v1.0
443
Download from Www.Somanuals.com. All Manuals Search And Download.
ip Commands
ip mcast rtadd
Add a multicast route to the multicast routing table.
SYNTAX:
ip mcast rtadd
srcintf = <{loop|Internet|LocalNetwork}>
[src = <ip-address]>
grp = <ip-address>
dstintf = <{loop|Internet|LocalNetwork}>
[ttl = <number{1-255}]>
[ttlincr = <{disabled|enabled}]>
where:
srcintf
src
The source IP interface.
REQUIRED
The source IP address.
OPTIONAL
REQUIRED
REQUIRED
OPTIONAL
OPTIONAL
grp
The multicast group IP address.
The destination IP interface.
dstintf
ttl
The time-to-live for that destination IP interface.
Increment TTL before packet is send.
ttlincr
E-DOC-CTC-20071119-0014 v1.0
447
Download from Www.Somanuals.com. All Manuals Search And Download.
ip Commands
ip mcast rtdelete
Delete a multicast route from the multicast routing table.
SYNTAX:
ip mcast rtdelete
srcintf = <{loop|Internet|LocalNetwork}>
[src = <ip-address]>
grp = <ip-address>
dstintf = <{loop|Internet|LocalNetwork}>
where:
srcintf
src
The source IP interface.
REQUIRED
The source IP address.
OPTIONAL
REQUIRED
REQUIRED
grp
The multicast group IP address.
The destination IP interface.
dstintf
E-DOC-CTC-20071119-0014 v1.0
448
Download from Www.Somanuals.com. All Manuals Search And Download.
ip Commands
ip rtadd
Add a route to the routing table.
SYNTAX:
ip rtadd
dst = <ip-address>
[dstmsk = <ip-mask(dotted or cidr)]>
[label = <{None|DSCP|Interactive|Management|
Video|VoIP-RTP|VoIP-Signal|default}]>
[gateway = <ip-address]>
[intf = <{loop|Internet|LocalNetwork}]>
[srcintf = <{loop|Internet|LocalNetwork}]>
[metric = <number{0-255}]>
where:
dst
The destination IP address(es) using this route.
Supports ip/mask notation.
REQUIRED
dstmsk
label
The destination IP address mask.
The name of a label.
OPTIONAL
OPTIONAL
OPTIONAL
gateway
The IP address of the next hop (direct connected
gateway or extended route)
intf
Only for special interface routes : the outgoing IP OPTIONAL
interface name.
srcintf
metric
Use this interface for source address selection.
The metric for this route (weight factor).
OPTIONAL
OPTIONAL
E-DOC-CTC-20071119-0014 v1.0
450
Download from Www.Somanuals.com. All Manuals Search And Download.
ip Commands
ip rtdelete
Delete a route from the routing table.
SYNTAX:
ip rtdelete
dst = <ip-address>
[dstmsk = <ip-mask(dotted or cidr)]>
[label = <{None|DSCP|Interactive|Management|
Video|VoIP-RTP|VoIP-Signal|default}]>
[gateway = <ip-address]>
[intf = <{loop|Internet|LocalNetwork}]>
where:
dst
The destination IP address specification of the
route to delete. Supports ip/mask notation.
REQUIRED
dstmsk
label
The destination IP address mask.
The name of a label.
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
gateway
intf
The IP address of the next hop.
The outgoing IP interface name. (For special
interface routes only).
E-DOC-CTC-20071119-0014 v1.0
451
Download from Www.Somanuals.com. All Manuals Search And Download.
ipqos Commands
ipqos config
Modify the IP QoS configuration for a given destination of an interface.
SYNTAX:
ipqos config
dest = <{atm_pvc_8_35}>
[state = <{disabled|enabled}]>
[discard = <{tail|early}]>
[priority = <{wfq|strict|wrr}]>
[realtimerate = <number{1-100}]>
[burstsize = <number{1-64}]>
[weight1 = <number{1-97}]>
[weight2 = <number{1-97}]>
[weight3 = <number{1-97}]>
[weight4 = <number{1-97}]>
[maxpackets = <number{0-250}]>
[maxbytes = <number{0-128}]>
where:
dest
The destination of the interface. Typically, a
phonebook entry.
REQUIRED
state
Enable, disable IP QoS for the interface.
OPTIONAL
OPTIONAL
discard
The packet discard strategy in case of
congestion.
priority
The subqueue priority algorithm.
The percentage of the bandwith.
Burstsize in kilo bytes (KB).
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
realtimerate
burstsize
weight1
The weight of queue 1 used for weighted fair
queueing (WFQ) or weighted round robin (WRR).
weight2
weight3
weight4
The weight of queue 2 used for weighted fair
queueing (WFQ) or weighted round robin (WRR).
OPTIONAL
OPTIONAL
OPTIONAL
The weight of queue 3 used for weighted fair
queueing (WFQ) or weighted round robin (WRR).
The weight of queue 4 used for weighted fair
queueing (WFQ) or weigthed round robin (WRR).
maxpackets
maxbytes
The maximum number of packets in all queues.
OPTIONAL
OPTIONAL
The maximum size in kilo bytes (KB) in all
queues.
E-DOC-CTC-20071119-0014 v1.0
454
Download from Www.Somanuals.com. All Manuals Search And Download.
ipqos Commands
ipqos ef config
Modify an IP QoS EF timer configuration for an interface.
SYNTAX:
ipqos ef config
intf = <{loop|Internet|LocalNetwork}>
[state = <{disabled|enabled}]>
[timeout = <number{100-10000}]>
[mtu = <number{68-65535}]>
where:
intf
The IP interface name.
REQUIRED
state
timeout
mtu
Enable, disable IP QoS EF timer for the interface. OPTIONAL
The timeout in mili seconds.
OPTIONAL
OPTIONAL
The MTU of the IP interface in case of EF data.
E-DOC-CTC-20071119-0014 v1.0
455
Download from Www.Somanuals.com. All Manuals Search And Download.
ipqos Commands
ipqos queue config
Modify the IP QoS subqueue configuration.
SYNTAX:
ipqos queue config
dest = <{atm_pvc_8_35}>
queue = <number{0-5}>
[propagate = <{disabled|enabled}]>
[ecnmarking = <{disabled|enabled}]>
[ackfiltering = <{disabled|enabled}]>
[maxpackets = <number{0-250}]>
[maxbytes = <number{0-128}]>
[respackets = <number{0-250}]>
[resbytes = <number{0-128}]>
[hold = <number]>
[markprob = <number{1-1000}]>
where:
dest
The destination of the interface. Typically, a
phonebook entry.
REQUIRED
queue
The number of the subqueue.
REQUIRED
OPTIONAL
propagate
Propagate the packets in lower priority queue
iso. dropping.
ecnmarking
Enable Explicit Congestion Notification for IP
packets in this subqueue.
OPTIONAL
ackfiltering
maxpackets
Enable filtering of TCP ACK packets.
OPTIONAL
OPTIONAL
The maximum number of packets in the
subqueue.
maxbytes
respackets
The maximum subqueue size in kilo bytes (KB).
OPTIONAL
OPTIONAL
The reserved number of packets in the
subqueue.
resbytes
hold
The reserved subqueue size in kilo bytes (KB).
OPTIONAL
OPTIONAL
The hold time in microseconds for early discard
strategy.
markprob
The maximum packet marking probability in
parts per mille for early discard strategy.
OPTIONAL
E-DOC-CTC-20071119-0014 v1.0
460
Download from Www.Somanuals.com. All Manuals Search And Download.
ipqos Commands
ipqos queue list
Display the IP QoS subqueue configuration.
SYNTAX:
ipqos queue list
where:
[dest = <{atm_pvc_8_35}]>
dest
The destination of the interface. Typically, a
phonebook entry.
OPTIONAL
E-DOC-CTC-20071119-0014 v1.0
461
Download from Www.Somanuals.com. All Manuals Search And Download.
ipqos Commands
ipqos queue stats
Display the IP QoS subqueue statistics.
SYNTAX:
ipqos queue stats
where:
[dest = <{atm_pvc_8_35}]>
dest
The destination of the interface. Typically, a
phonebook entry.
OPTIONAL
E-DOC-CTC-20071119-0014 v1.0
462
Download from Www.Somanuals.com. All Manuals Search And Download.
label Commands
label modify
Modify a label configuration.
SYNTAX:
label modify
name = <{DSCP|Interactive|Management|Video|
VoIP-RTP|VoIP-Signal|default}>
[classification = <{ignore|overwrite|
increase}]>
[defclass = <{0|1|2|3|4|5|6|7|8|9|10|11|12|13|
14|15|dscp|default}]>
[ackclass = <{0|1|2|3|4|5|6|7|8|9|10|11|12|13|
14|15|prioritize|defclass}]>
[bidirectional = <{disabled|enabled}]>
[inheritance = <{disabled|enabled}]>
[tosmarking = <{disabled|enabled}]>
[tos = <number{0-255}]>
[dscp = <{ef|af11|af12|af13|af21|af22|af23|
af31|af32|af33|af41|af42|af43|cs0|cs1|cs2|cs3|
cs4|cs5|cs6|cs7} or number]>
[precedence = <{routine|priority|immediate|
flash|flash-override|CRITIC-ECP|internetwork-
control|network-control} or number]>
[trace = <{disabled|enabled}]>
where:
name
The name of a label to modify.
REQUIRED
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
classification
defclass
The Method of classification.
The default class of assigned connection.
The class of ACK segments of TCP connection.
The label is also valid for returning stream.
ackclass
bidirectional
inheritance
The label is also valid for corresponding stream
of child connection.
tosmarking
tos
Enable/disable TOS marking.
OPTIONAL
The Type Of Service specification in the IP packet OPTIONAL
(used for tos- marking).
dscp
The diffserv code point (part of tos, used for tos-
marking).
OPTIONAL
OPTIONAL
OPTIONAL
precedence
trace
The precedence (part of tos, used for tos-
marking).
Enable/disable IP tracing for this label.
E-DOC-CTC-20071119-0014 v1.0
472
Download from Www.Somanuals.com. All Manuals Search And Download.
label Commands
label rule add
Add a rule.
SYNTAX:
label rule add
chain = <chain name>
[index = <number]>
[name = <string]>
[clink = <chain name]>
[srcintf [!] = <{wan|local|lan|tunnel|dmz|
guest}]>
[srcip [!] = <{private|ssdp_ip|mdap_ip}]>
[dstip [!] = <{private|ssdp_ip|mdap_ip}]>
[serv [!] = <{icmp|igmp|ftp|telnet|http|
httpproxy|https|RPC|NBT|SMB|imap|esp|ah|
ike|DiffServ|sip|h323|dhcp|rtsp|ssdp_serv|
mdap_serv|syslog}]>
[log = <{disabled|enabled}]>
[state = <{disabled|enabled}]>
label = <{None|link|DSCP|Interactive|
Management|Video|VoIP-RTP|VoIP-Signal|
default}>
where:
chain
index
name
clink
The name of the chain which contains the rule.
The index of the rule in the chain.
The name of the new rule.
REQUIRED
OPTIONAL
OPTIONAL
OPTIONAL
The name of the chain to be parsed when this
rule applies.
srcintf [!]
srcip [!]
dstip [!]
serv [!]
The name of the source interface expression.
If a value is preceded by a
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
The name of the source ip expression.
If a value is preceded by a
The name of the destination ip expression.
If a value is preceded by a
The name of the service expression.
If a value is preceded by a
log
Disable/Enable logging when this rule applies.
Disable/Enable this rule.
OPTIONAL
OPTIONAL
REQUIRED
state
label
None, link (when clink is used) or label name.
E-DOC-CTC-20071119-0014 v1.0
473
Download from Www.Somanuals.com. All Manuals Search And Download.
label Commands
label rule delete
Delete a rule.
SYNTAX:
label rule delete
chain = <chain name>
index = <number>
where:
chain
The name of the chain in which to delete the
rule.
REQUIRED
REQUIRED
index
The number of the rule in the chain.
E-DOC-CTC-20071119-0014 v1.0
474
Download from Www.Somanuals.com. All Manuals Search And Download.
label Commands
label rule list
Display a list of rules.
SYNTAX:
label rule list
[chain = <chain name]>
[format = <{pretty|cli}]>
where:
chain
The name of the chain to list the rules of.
The format of the rule list.
OPTIONAL
OPTIONAL
format
E-DOC-CTC-20071119-0014 v1.0
476
Download from Www.Somanuals.com. All Manuals Search And Download.
label Commands
label rule modify
Modify a rule.
SYNTAX:
label rule modify
chain = <chain name>
[index = <number]>
[newindex = <number]>
[name = <string]>
[clink = <chain name]>
[[!]srcintf] = <chain name]>
[[!]srcip] = <chain name]>
[[!]dstip] = <chain name]>
[[!]serv] = <chain name]>
[log = <{disabled|enabled}]>
[state = <{disabled|enabled}]>
[label = <{None|link|DSCP|Interactive|
Management|Video|VoIP-RTP|VoIP-Signal|
default}]>
where:
chain
The name of the chain which contains the rule.
The index of the rule in the chain.
The new index of the rule in the chain.
The name of the new rule.
REQUIRED
index
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
newindex
name
clink
The name of the chain to be parsed when this
rule applies.
[!]srcintf]
[!]srcip]
[!]dstip]
[!]serv]
The name of the source interface expression.
If a value is preceded by a
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
The name of the source ip expression.
If a value is preceded by a
The name of the destination ip expression.
If a value is preceded by a
The name of the service expression.
If a value is preceded by a
log
Disable/Enable logging when this rule applies.
Disable/Enable this rule.
OPTIONAL
OPTIONAL
OPTIONAL
state
label
None, link (when clink is used) or label name.
E-DOC-CTC-20071119-0014 v1.0
477
Download from Www.Somanuals.com. All Manuals Search And Download.
language Commands
E-DOC-CTC-20071119-0014 v1.0
478
Download from Www.Somanuals.com. All Manuals Search And Download.
language Commands
language config
Select a language.
SYNTAX:
language config
[language = <string]>
[complete = <{yes|no}]>
where:
language
Language code : OSI language code (2 chars) for OPTIONAL
language (en=English)
complete
Enable translation for expert pages.
OPTIONAL
E-DOC-CTC-20071119-0014 v1.0
480
Download from Www.Somanuals.com. All Manuals Search And Download.
language Commands
language delete
Delete one or all language archives.
SYNTAX:
language delete
[file = <string]>
[all = <{yes|no}]>
where:
file
all
Filename : name of language archive to delete
Deletes all languages archives.
OPTIONAL
OPTIONAL
E-DOC-CTC-20071119-0014 v1.0
481
Download from Www.Somanuals.com. All Manuals Search And Download.
mbus Commands
mbus client authenticate
Authenticate a session
SYNTAX:
mbus client authenticate
type = <{cleartext|md5|crypt|digest}>
username = <quoted string>
password = <password>
where:
type
Authentication type
User name
REQUIRED
REQUIRED
REQUIRED
username
password
password
E-DOC-CTC-20071119-0014 v1.0
484
Download from Www.Somanuals.com. All Manuals Search And Download.
mbus Commands
mbus client config
Modify client parameters
SYNTAX:
mbus client config
[writelock = <{enabled|disabled}]>
[wlgetimeout = <number]>
[wlidletimeout = <number]>
[path = <quoted string]>
[type = <{indexpath|objidpath|keystrpath}]>
[id = <number]>
where:
writelock
Get/release mbus writelock
OPTIONAL
wlgetimeout
Writelock get timeout in seconds (forever=-1,
*default=nowait=0)
OPTIONAL
wlidletimeout
Writelock idle timeout in seconds (forever=-1,
*default=30)
OPTIONAL
path
type
id
Fully qualified mbus path
Path type (default = indexpath)
sessionid to use
OPTIONAL
OPTIONAL
OPTIONAL
E-DOC-CTC-20071119-0014 v1.0
485
Download from Www.Somanuals.com. All Manuals Search And Download.
mbus Commands
mbus client exec
Execute mbus command
SYNTAX:
mbus client exec
cmd = <{getpath|getcount|getnames|getvalues|
setvalue|addobject|deleteobject|subscribe|
unsubscribe|getaccessrights|setaccessrights}>
[param = <quoted string]>
[value = <quoted string]>
[gettype = <{parameter|path|object}]>
[depth = <number]>
[processcmd = <{enabled|disabled}]>
[onerrorrollback = <{enabled|disabled}]>
[usecallback = <{enabled|disabled}]>
[filter = <quoted string]>
[path = <quoted string]>
[flags = <[+/-]flag[+/-flag...]{indexpath
objidpath keystrpath uncommitted xref_localidx
xref_objid xref_keypath exact_depth
applyonparamsapplyrecursive typetreepath
non_persistent}]>
[accesslist = <quoted string]>
[action = <[+/-]flag[+/-flag...]{read write
attrchg}]>
[modifier = <{add|delete|allow_only|
allow_except}]>
[replytype = <{getallowed|getdisallowed|
getasconfigured}]>
[attribute = <{ar_archg|ar_read|ar_write|
param_cached|param_eventable|object_dynamic}]>
where:
cmd
Mbus command name
REQUIRED
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
param
value
Parameter name
Parameter value to set
gettype
depth
Get type elements (default=param)
Number of levels to recurse, default=-1 (all)
processcmd
Process SET_VALUE command flag
(default=enabled)
onerrorrollback
usecallback
filter
on error rollback flag (default=enabled)
OPTIONAL
OPTIONAL
OPTIONAL
Use result callback function (default=enabled)
The filter should be formatted as '(operator
operand operand)'. Possible operators are ==, !
E-DOC-CTC-20071119-0014 v1.0
486
Download from Www.Somanuals.com. All Manuals Search And Download.
mbus Commands
=, <, <=, >, >=, and, or, not. The left operand
is a parameter name. The right operand is a
parameter value. For boolean operators the
operands are filters. Example: '(== Name eth0)'.
path
Fully qualified mbus path
Client command data flags
OPTIONAL
OPTIONAL
flags
accesslist
action
Comma separated names of accessrights groups OPTIONAL
Type of accessright action
Accessrights modifier
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
modifier
replytype
attribute
Type of accessrights reply
Requested attribute-type
E-DOC-CTC-20071119-0014 v1.0
487
Download from Www.Somanuals.com. All Manuals Search And Download.
mbus Commands
mbus client register
Register cli client to mbus
SYNTAX:
mbus client register
[dmtree = <{igd|atomic|system}]>
[type = <{indexpath|objidpath|keystrpath}]>
[dlink = <{local_ipc|remote_inet}]>
[mbusd_addr = <quoted string]>
[refresolv = <{disabled|enabled}]>
where:
dmtree
type
Select mbusd datamodel tree.
OPTIONAL
Path type (default = indexpath)
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
dlink
Daemon link (default = local_ipc)
Daemon address (ip addr for inet)
Use reference resolving (default=disabled)
mbusd_addr
refresolv
E-DOC-CTC-20071119-0014 v1.0
488
Download from Www.Somanuals.com. All Manuals Search And Download.
mbus Commands
mbus debug loadobjects
Load/sync object instances from plugins
SYNTAX:
mbus debug loadobjects
[dmtree = <{igd|atomic|system}]>
[path = <quoted string]>
[type = <{indexpath|objidpath|keystrpath}]>
[flush = <{disabled|enabled}]>
where:
dmtree
path
Select mbusd datamodel tree.
Fully qualified mbus path
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
type
Path type (default = indexpath
Flush objects before load (default=disabled)
flush
E-DOC-CTC-20071119-0014 v1.0
492
Download from Www.Somanuals.com. All Manuals Search And Download.
mbus Commands
mbus debug unloadobjects
Unload object instances
SYNTAX:
mbus debug unloadobjects
[dmtree = <{igd|atomic|system}]>
[path = <quoted string]>
[type = <{indexpath|objidpath|keystrpath}]>
[flush = <{disabled|enabled}]>
where:
dmtree
path
Select mbusd datamodel tree.
Fully qualified mbus path
Path type
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
type
flush
Flush objects before load (default=disabled)
E-DOC-CTC-20071119-0014 v1.0
495
Download from Www.Somanuals.com. All Manuals Search And Download.
mbus Commands
mbus listcontexts
Display the context instances
SYNTAX:
mbus listcontexts
[dmtree = <{igd|atomic|system}]>
[expand = <{disabled|enabled}]>
where:
dmtree
expand
Select mbusd datamodel tree.
Details enabled/disabled
OPTIONAL
OPTIONAL
E-DOC-CTC-20071119-0014 v1.0
496
Download from Www.Somanuals.com. All Manuals Search And Download.
mbus Commands
mbus listenums
Display the registered enumtypes
SYNTAX:
mbus listenums
[dmtree = <{igd|atomic|system}]>
[name = <quoted string]>
[expand = <{disabled|enabled}]>
where:
dmtree
name
Select mbusd datamodel tree.
Filter enumtypes by (part of) the name
Details enabled/disabled
OPTIONAL
OPTIONAL
OPTIONAL
expand
E-DOC-CTC-20071119-0014 v1.0
497
Download from Www.Somanuals.com. All Manuals Search And Download.
mbus Commands
mbus listobjects
Display the object instances
SYNTAX:
mbus listobjects
[dmtree = <{igd|atomic|system}]>
[path = <quoted string]>
[type = <{indexpath|objidpath|keystrpath}]>
[output = <{tree|list}]>
[showflags = <{disabled|enabled}]>
where:
dmtree
path
Select mbusd datamodel tree.
Fully qualified mbus path to list.
Path type (default = indexpath)
List output type
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
type
output
showflags
Display object flags (Clean or Dirty / Persistent or OPTIONAL
Volatile)
E-DOC-CTC-20071119-0014 v1.0
498
Download from Www.Somanuals.com. All Manuals Search And Download.
mbus Commands
mbus listtypes
Display the registered objecttypes
SYNTAX:
mbus listtypes
[dmtree = <{igd|atomic|system}]>
[path = <quoted string]>
[expand = <{disabled|enabled}]>
where:
dmtree
path
Select mbusd datamodel tree.
Fully qualified mbus path to list.
Details enabled/disabled
OPTIONAL
OPTIONAL
OPTIONAL
expand
E-DOC-CTC-20071119-0014 v1.0
500
Download from Www.Somanuals.com. All Manuals Search And Download.
mbus Commands
mbus pluginevent
Simulate event from plugin
SYNTAX:
mbus pluginevent
ctxid = <number{0--2}>
type = <{addobj|delobj|updobj}>
path = <quoted string>
[name = <quoted string]>
[value = <quoted string]>
[orivalue = <quoted string]>
where:
ctxid
Plugin context id
REQUIRED
REQUIRED
REQUIRED
OPTIONAL
OPTIONAL
OPTIONAL
type
Event type
path
Plugin event subpath
Plugin event name
Plugin event value
Plugin event orivalue
name
value
orivalue
E-DOC-CTC-20071119-0014 v1.0
501
Download from Www.Somanuals.com. All Manuals Search And Download.
memm Commands
memm debug lock traceconfig
Modify lock trace settings.
SYNTAX:
memm debug lock traceconfig
[level = <number{0-4}]>
[name = <string]>
where:
level
Select memm trace level (0-4).
OPTIONAL
name
application name filter for lock traces (empty
displays all lock traces)
OPTIONAL
E-DOC-CTC-20071119-0014 v1.0
506
Download from Www.Somanuals.com. All Manuals Search And Download.
memm Commands
memm debug tag
(Un)tag memory manager objects.
SYNTAX:
memm debug tag
[name = <quoted string]>
[tag = <{enabled|disabled}]>
where:
name
Select typename(s) to list (supports partial
typename)
OPTIONAL
OPTIONAL
tag
Set (or unset) the tag
E-DOC-CTC-20071119-0014 v1.0
508
Download from Www.Somanuals.com. All Manuals Search And Download.
memm Commands
memm listobjects
Display objects.
SYNTAX:
memm listobjects
[name = <quoted string]>
[tagged = <{no|yes}]>
[hidedeldynstr = <{no|yes}]>
where:
name
Select typename(s) to list (supports partial
typename)
OPTIONAL
tagged
Show only tagged (yes) or untagged (no) objects OPTIONAL
hidedeldynstr
Hide (yes) / show (no) deleted dynstrings
(default = show)
OPTIONAL
E-DOC-CTC-20071119-0014 v1.0
510
Download from Www.Somanuals.com. All Manuals Search And Download.
menu Command
E-DOC-CTC-20071119-0014 v1.0
512
Download from Www.Somanuals.com. All Manuals Search And Download.
mlp Commands
E-DOC-CTC-20071119-0014 v1.0
514
Download from Www.Somanuals.com. All Manuals Search And Download.
mlp Commands
mlp privilege add
Add a privilege.
SYNTAX:
mlp privilege add
name = <string>
type = <{access|service}>
[descr = <quoted string]>
where:
name
type
Privilege name.
REQUIRED
REQUIRED
OPTIONAL
Privilege type.
descr
Privilege description.
E-DOC-CTC-20071119-0014 v1.0
521
Download from Www.Somanuals.com. All Manuals Search And Download.
mlp Commands
mlp privilege addzone
Add a zone to a privilege.
SYNTAX:
mlp privilege addzone
name = <>
zone = <{Read/LAN/WAN/Local|Write/LAN/WAN/
Local|r_lan|r_wan|r_fs_view|r_certificates|
r_remote_mgnt|r_local|r_qos|w_lan|w_wan|
w_fs_passive|w_rtg|w_fwdg|w_nat|w_frwl_norm|
w_frwl_adv|w_frwl_ss|w_ipsec|w_certificates|
w_remote_mgnt|w_local|w_qos|SND_lan|SND_wan|
SND_local|AND_lan|AND_wan|AND_frwl|AND_local|
User_Admin|MLP_Admin|secure_ipsec_term|
secure_BR|CLI|CGI|FTP|MDAP|secure_reset|
GUI_advanced|mbus|unsecure_connection|
Sensitve_file|...}>
where:
name
zone
Privilege name.
Zone name.
REQUIRED
REQUIRED
E-DOC-CTC-20071119-0014 v1.0
522
Download from Www.Somanuals.com. All Manuals Search And Download.
mlp Commands
mlp privilege config
Modify the privilege.
SYNTAX:
mlp privilege config
name = <>
[descr = <quoted string]>
[score = <{hex-word}[:{hex-word}] ex:
'a12:c30f']>
where:
name
descr
score
Select the privilege by name.
Set the description.
Set the score.
REQUIRED
OPTIONAL
OPTIONAL
E-DOC-CTC-20071119-0014 v1.0
523
Download from Www.Somanuals.com. All Manuals Search And Download.
mlp Commands
mlp privilege list
Display the privileges.
SYNTAX:
mlp privilege list
[name = <]>
[type = <{access|service}]>
[verbose = <{minimal|medium|all}]>
where:
name
type
Privilege name.
OPTIONAL
OPTIONAL
OPTIONAL
Privilege type.
verbose
Limit the output list.
E-DOC-CTC-20071119-0014 v1.0
525
Download from Www.Somanuals.com. All Manuals Search And Download.
mlp Commands
mlp privilege removezone
Remove a zone from a privilege.
SYNTAX:
mlp privilege removezone
name = <>
zone = <{Read/LAN/WAN/Local|Write/LAN/WAN/
Local|r_lan|r_wan|r_fs_view|r_certificates|
r_remote_mgnt|r_local|r_qos|w_lan|w_wan|
w_fs_passive|w_rtg|w_fwdg|w_nat|w_frwl_norm|
w_frwl_adv|w_frwl_ss|w_ipsec|w_certificates|
w_remote_mgnt|w_local|w_qos|SND_lan|SND_wan|
SND_local|AND_lan|AND_wan|AND_frwl|AND_local|
User_Admin|MLP_Admin|secure_ipsec_term|
secure_BR|CLI|CGI|FTP|MDAP|secure_reset|
GUI_advanced|mbus|unsecure_connection|
Sensitve_file|...}>
where:
name
zone
Privilege name.
Zone name.
REQUIRED
REQUIRED
E-DOC-CTC-20071119-0014 v1.0
526
Download from Www.Somanuals.com. All Manuals Search And Download.
mlp Commands
mlp role add
Add a role.
SYNTAX:
mlp role add
name = <string>
parent = <>
[descr = <quoted string]>
where:
name
parent
descr
Role name.
REQUIRED
REQUIRED
OPTIONAL
Parent role name.
Role description.
E-DOC-CTC-20071119-0014 v1.0
527
Download from Www.Somanuals.com. All Manuals Search And Download.
mlp Commands
mlp role addpriv
Add a privilege.
SYNTAX:
mlp role addpriv
name = <{Administrator|LAN_Admin|PowerUser|
root|SuperUser|TechnicalSupport|User|
WAN_Admin}>
access = <{anyaccess|AP1|AP2|AP3|AP4|AP5|AP6|
AP7|AP8|AP9}>
service = <{anyservice|SP1|SP10|SP11|SP12|
SP13|SP14|SP15|SP16|SP17|SP18|SP19|SP2|SP3|
SP4|SP5|SP6|SP7|SP8|SP9}>
where:
name
Role name.
REQUIRED
REQUIRED
REQUIRED
access
service
Access privilege to add.
Privilege name to add.
E-DOC-CTC-20071119-0014 v1.0
528
Download from Www.Somanuals.com. All Manuals Search And Download.
mlp Commands
mlp role config
Modify the role.
SYNTAX:
mlp role config
name = <>
[parent = <]>
[descr = <quoted string]>
where:
name
parent
descr
Role name.
REQUIRED
OPTIONAL
OPTIONAL
Parent role name.
Role description.
E-DOC-CTC-20071119-0014 v1.0
529
Download from Www.Somanuals.com. All Manuals Search And Download.
mlp Commands
mlp role removepriv
Remove a privilege.
SYNTAX:
mlp role removepriv
name = <>
access = <>
[service = <]>
where:
name
Role name.
REQUIRED
REQUIRED
OPTIONAL
access
service
Access privilege to delete.
Privilege name to delete.
E-DOC-CTC-20071119-0014 v1.0
532
Download from Www.Somanuals.com. All Manuals Search And Download.
nat Commands
nat ifconfig
Modify address translation on an IP interface.
SYNTAX:
nat ifconfig
intf = <{loop|Internet|LocalNetwork}>
translation = <{disabled|enabled|transparent}>
where:
intf
The IP interface name.
REQUIRED
REQUIRED
translation
Disabled, enabled or tranparent address
translation.
E-DOC-CTC-20071119-0014 v1.0
536
Download from Www.Somanuals.com. All Manuals Search And Download.
nat Commands
nat mapadd
Add an address mapping to a nat enabled interface.
SYNTAX:
nat mapadd
intf = <{loop|Internet|LocalNetwork}>
[type = <{napt|nat}]>
[outside_addr = <ip-range]>
[inside_addr = <ip-range]>
[access_list = <ip-range]>
[foreign_addr = <ip-range]>
[protocol = <{ah|egp|esp|ggp|gre|hmp|icmp|
igmp|pup|rdp|rsvp|tcp|udp|vines|xns-idp|6to4|
ipip} or number]>
[outside_port = <port-range]>
[inside_port = <port-range]>
[mode = <{auto|inbound|outbound}]>
[weight = <number{0-255}]>
where:
intf
The IP interface name.
The type of mapping.
REQUIRED
OPTIONAL
OPTIONAL
type
outside_addr
The outside (typically public) IP address (range
for NAT).
inside_addr
access_list
The inside (typically private) IP address (range
for NAT).
OPTIONAL
OPTIONAL
The range of inside addresses the mapping is
restricted to.
foreign_addr
The range of destination addresses the mapping OPTIONAL
is restricted to.
protocol
The IP protocol.
OPTIONAL
OPTIONAL
outside_port
The outside port number or range (only for
NAPT).
inside_port
The inside port number or range (only for
NAPT).
OPTIONAL
mode
The mode to create the portmap.
The weight for the portmap.
OPTIONAL
OPTIONAL
weight
E-DOC-CTC-20071119-0014 v1.0
538
Download from Www.Somanuals.com. All Manuals Search And Download.
nat Commands
nat mapdelete
Delete an address mapping from a nat enabled interface.
SYNTAX:
nat mapdelete
intf = <{loop|Internet|LocalNetwork}>
index = <number>
where:
intf
The IP interface name.
REQUIRED
REQUIRED
index
The map index as listed by ':nat maplist'.
E-DOC-CTC-20071119-0014 v1.0
539
Download from Www.Somanuals.com. All Manuals Search And Download.
nat Commands
nat maplist
Display address mappings.
SYNTAX:
nat maplist
[intf = <{loop|Internet|LocalNetwork}]>
[expand = <{disabled|enabled}]>
where:
intf
The IP interface name.
Expanded listing.
OPTIONAL
OPTIONAL
expand
E-DOC-CTC-20071119-0014 v1.0
540
Download from Www.Somanuals.com. All Manuals Search And Download.
nat Commands
nat tmpladd
Add an address mapping template.
SYNTAX:
nat tmpladd
[intf = <{loop|Internet|LocalNetwork}]>
[group = <{wan|local|lan|tunnel|dmz|guest} or
number]>
[timeout = <number{0-65535}]>
[type = <{napt|nat}]>
outside_addr = <ip-range>
[inside_addr = <ip-range]>
[access_list = <ip-range]>
[foreign_addr = <ip-range]>
[protocol = <{ah|egp|esp|ggp|gre|hmp|icmp|
igmp|pup|rdp|rsvp|tcp|udp|vines|xns-idp|6to4|
ipip} or number]>
[outside_port = <port-range]>
[inside_port = <port-range]>
[mode = <{auto|inbound|outbound}]>
[weight = <number{0-255}]>
where:
intf
The IP interface name scope for this template.
The IP interface group scope for this template.
Lifetime (seconds) for this template.
The type of template.
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
group
timeout
type
outside_addr
The outside (typically public) IP address or index REQUIRED
(range for NAT).
inside_addr
access_list
The inside (typically private) IP address or index
(range for NAT).
OPTIONAL
OPTIONAL
OPTIONAL
The range of inside addresses the template is
restricted to.
foreign_addr
The range of destination addresses the template
is restricted to.
protocol
The IP protocol.
OPTIONAL
OPTIONAL
outside_port
The outside port number or range (only for
NAPT).
inside_port
mode
The inside port number or range (only for
NAPT).
OPTIONAL
OPTIONAL
The mode to create the portmap.
E-DOC-CTC-20071119-0014 v1.0
541
Download from Www.Somanuals.com. All Manuals Search And Download.
nat Commands
weight
The weight to be used for the template
instance(s).
OPTIONAL
E-DOC-CTC-20071119-0014 v1.0
542
Download from Www.Somanuals.com. All Manuals Search And Download.
nat Commands
nat tmplinst
Instantiate address mapping templates for a given dynamic address.
SYNTAX:
nat tmplinst
intf = <{loop|Internet|LocalNetwork}>
addr_index = <ip-address>
dynamic_addr = <ip-address>
where:
intf
The IP interface name.
REQUIRED
addr_index
The outside IP address index/key to instantiate
for.
REQUIRED
dynamic_addr
The dynamic address to substitute the index/key
with.
REQUIRED
E-DOC-CTC-20071119-0014 v1.0
544
Download from Www.Somanuals.com. All Manuals Search And Download.
ping Command
E-DOC-CTC-20071119-0014 v1.0
546
Download from Www.Somanuals.com. All Manuals Search And Download.
ping Command
ping Command
Send ICMP ECHO_REQUEST packets.
SYNTAX:
ping
proto = <{ip|atm}>
addr = <ip-address>
dest = <{atm_pvc_8_35}>
[count = <number{0-1000000}]>
[size = <number{28-20028}]>
[interval(ms) = <number{100-1000000}]>
[DF-bit = <{disabled|enabled}]>
[srcaddr = <ip-address]>
where:
proto
addr
dest
The interface type to be used.
The destination IP address.
REQUIRED
REQUIRED
REQUIRED
OPTIONAL
The destination address for the request.
count
The number of pings to send (0 is continuous
ping).
size
The size of the ping datagram(s).
OPTIONAL
OPTIONAL
interval(ms)
DF-bit
The interval in milliseconds between packets.
Set the Don't Fragment bit (or leave unset) in the OPTIONAL
IP header of ping
srcaddr
The IP source address to use.
OPTIONAL
E-DOC-CTC-20071119-0014 v1.0
547
Download from Www.Somanuals.com. All Manuals Search And Download.
ppp Commands
E-DOC-CTC-20071119-0014 v1.0
548
Download from Www.Somanuals.com. All Manuals Search And Download.
ppp Commands
ppp ifadd
Create a new PPP interface.
SYNTAX:
ppp ifadd
where:
intf = <string>
intf
The name for the new PPP interface. If not
specified, the destination will double as interface
name.
REQUIRED
E-DOC-CTC-20071119-0014 v1.0
551
Download from Www.Somanuals.com. All Manuals Search And Download.
ppp Commands
ppp ifconfig
Modify a PPP interface.
SYNTAX:
ppp ifconfig
intf = <{Internet}>
[dest = <{RELAY}]>
[user = <string]>
[password = <password]>
[acname = <quoted string]>
[servicename = <quoted string]>
[pool = <{none}]>
[pcomp = <{disabled|enabled}]>
[accomp = <{enabled|disabled|negotiate}]>
[trace = <{disabled|enabled}]>
[concentrator = <{disabled|enabled}]>
[auth = <{pap|chap|auto}]>
[restart = <{disabled|enabled}]>
[retryinterval = <number{0-65535}]>
[passive = <{disabled|enabled}]>
[silent = <{disabled|enabled}]>
[echo = <{disabled|enabled}]>
[echotolerance = <number{1-100}]>
[mru = <number{293-8192}]>
[laddr = <ip-address]>
[raddr = <ip-address]>
[netmask = <ip-mask(dotted or cidr)]>
[format = <{cidr|dotted|none}]>
[savepwd = <{disabled|enabled}]>
[demanddial = <{disabled|enabled}]>
[doddelay = <number{0-3600}]>
[primdns = <ip-address]>
[secdns = <ip-address]>
[dnsmetric = <number{0-100}]>
[idletime = <number{0-1000000}]>
[idletrigger = <{RxTx|Rx|Tx}]>
[unnumbered = <{disabled|enabled}]>
where:
intf
The name of the PPP interface to configure.
The destination interface for this PPP interface.
REQUIRED
dest
user
OPTIONAL
OPTIONAL
The username for remote PAP/CHAP
authentication.
password
acname
The password for remote PAP/CHAP
authentication.
OPTIONAL
The access concentrator name for a PPP session. OPTIONAL
E-DOC-CTC-20071119-0014 v1.0
553
Download from Www.Somanuals.com. All Manuals Search And Download.
ppp Commands
servicename
pool
The service name for a PPP session.
OPTIONAL
Acquire IP subnet and assign it to a free DHCP
pool.
OPTIONAL
OPTIONAL
OPTIONAL
pcomp
Try to negotiate PPP protocol compression (LCP
PCOMP).
accomp
Try to negotiate PPP address & control field
compression (LCP ACCOMP).
trace
Enable verbose console logging.
OPTIONAL
OPTIONAL
concentrator
The access concentrator is on this side of the
PPP connection.
auth
Authentication protocol to be used.
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
restart
Automatically restart when LCP link goes down.
The number of seconds between retries.
When LCP times out, put link in a listening state.
retryinterval
passive
silent
Do not send anything at startup, just listen for
incoming LCP messages.
echo
Send LCP echo requests at regular intervals.
OPTIONAL
OPTIONAL
echotolerance
Number of failed LCP echo requests needed to
trigger a link failure.
mru
Negotiate maximum packet size we can handle.
Negotiate this IP address at our side of the link.
OPTIONAL
OPTIONAL
OPTIONAL
laddr
raddr
Negotiate this IP address at remote side of the
link.
netmask
Negotiate IP subnet mask at remote side of the
link.
OPTIONAL
format
The format used to represent the IP subnet.
Select whether or not password is saved.
OPTIONAL
OPTIONAL
OPTIONAL
savepwd
demanddial
Enable dial-on-demand feature. Nothing
happens until packets are sent to this PPP
interface.
doddelay
During this initial interval (seconds) packets do
not trigger PPP interface.
OPTIONAL
primdns
secdns
Negotiate IP address as primary DNS server.
Negotiate IP address as secondary DNS server.
OPTIONAL
OPTIONAL
E-DOC-CTC-20071119-0014 v1.0
554
Download from Www.Somanuals.com. All Manuals Search And Download.
ppp Commands
dnsmetric
DNS route metric to be used for the negotiated
DNS servers.
OPTIONAL
idletime
Maximum time the link may be idle (seconds).
OPTIONAL
OPTIONAL
idletrigger
Consider the link being idle if no traffic is sent
and/or received during the idle time.
unnumbered
Take local IP address from 'laddr' field and
remote IP address from the pool. SVC only.
OPTIONAL
E-DOC-CTC-20071119-0014 v1.0
555
Download from Www.Somanuals.com. All Manuals Search And Download.
ppp Commands
ppp ifscan
Scan a PPP interface for available interfaces.
SYNTAX:
ppp ifscan
intf = <{Internet}>
[time = <number{0-36000}]>
where:
intf
The name of the PPP interface to scan.
The time to scan for services (in seconds).
REQUIRED
OPTIONAL
time
E-DOC-CTC-20071119-0014 v1.0
559
Download from Www.Somanuals.com. All Manuals Search And Download.
ppp Commands
ppp relay ifconfig
Modify an ethernet interface from the PPP relay agent list.
SYNTAX:
ppp relay ifconfig
intf = <{bridge|ethoa_8_35}>
hwaddr = <hardware-address>
where:
intf
The ethernet intf to be added to the PPP relay
agent list.
REQUIRED
REQUIRED
hwaddr
The hardware address (e.g. Ethernet MAC
address) of this interface.
E-DOC-CTC-20071119-0014 v1.0
562
Download from Www.Somanuals.com. All Manuals Search And Download.
ppp Commands
ppp relay ifdelete
Delete an ethernet interface from the PPP relay agent list.
SYNTAX:
ppp relay ifdelete
intf = <{bridge|ethoa_8_35}>
where:
intf
The ethernet intf to be added to the PPP relay
agent list.
REQUIRED
E-DOC-CTC-20071119-0014 v1.0
563
Download from Www.Somanuals.com. All Manuals Search And Download.
ppp Commands
ppp rtadd
Add a route to the routing table when PPP link comes up.
SYNTAX:
ppp rtadd
intf = <{Internet}>
dst = <ip-address>
[dstmsk = <ip-mask(dotted or cidr)]>
[label = <{None|DSCP|Interactive|Management|
Video|VoIP-RTP|VoIP-Signal|default}]>
[src = <ip-address]>
[srcmsk = <ip-mask(dotted or cidr)]>
[metric = <number{0-100}]>
where:
intf
dst
The name of a PPP interface.
REQUIRED
REQUIRED
The IP destination address specification for the
route to be added when the link comes up.
dstmsk
The IP destination mask. Special values : 1 =
remote net; 32 = remote host;
OPTIONAL
label
src
The name of the label.
OPTIONAL
OPTIONAL
The IP source address specification. i.e. who can
use this link.
srcmsk
metric
The IP source mask.
The route metric.
OPTIONAL
OPTIONAL
E-DOC-CTC-20071119-0014 v1.0
566
Download from Www.Somanuals.com. All Manuals Search And Download.
pptp Commands
E-DOC-CTC-20071119-0014 v1.0
568
Download from Www.Somanuals.com. All Manuals Search And Download.
pptp Commands
pptp ifadd
Adds a PPTP profile (backwards compatible with previous release, use profiles
SYNTAX:
pptp ifadd
dest = <string>
[rate = <number{10-10000}]>
[encaps = <{vcmux|nlpid}]>
[ac = <{never|always|keep}]>
where:
dest
The WAN destination for this PPTP tunnel.
Typically a phonebook name.
REQUIRED
rate
Transmit speed in kbits/s for the WAN link.
The WAN protocol encapsulation.
OPTIONAL
OPTIONAL
encaps
ac
Enable/disable sending address and control field OPTIONAL
(0xFF03) on the WAN link.
E-DOC-CTC-20071119-0014 v1.0
571
Download from Www.Somanuals.com. All Manuals Search And Download.
pptp Commands
pptp profadd
Defines a new PPTP profile.
SYNTAX:
pptp profadd
name = <string>
[qos = <{default}]>
[encaps = <{vcmux|nlpid}]>
[ac = <{never|always|keep}]>
where:
name
qos
The name for the new PPTP profile.
REQUIRED
OPTIONAL
The name of the qosbook entry, containing the
settings for this profile.
encaps
ac
The WAN protocol encapsulation to be used with OPTIONAL
this profile.
Enable/disable sending address and control field OPTIONAL
(0xFF03) on the WAN link.
E-DOC-CTC-20071119-0014 v1.0
573
Download from Www.Somanuals.com. All Manuals Search And Download.
ra Commands
E-DOC-CTC-20071119-0014 v1.0
576
Download from Www.Somanuals.com. All Manuals Search And Download.
ra Commands
ra config
Configure remote access parameters.
SYNTAX:
ra config
[state = <{disabled|enabled}]>
[secure = <{enabled|disabled}]>
[port = <number]>
[timeout = <number]>
[mode = <{Permanent|Temporary}]>
[ipintf = <string]>
[randompassword = <{enabled|disabled}]>
[randomport = <{enabled|disabled}]>
[group = <string]>
[user = <string]>
where:
state
Enable/disable RAD.
OPTIONAL
secure
Use secure mode (https).
The port number.
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
port
timeout
mode
The timeout value.
Mode Permanent or Temporary.
The name of the xref to the IP interface.
Create a random password.
Use a random port.
ipintf
randompassword
randomport
group
The name of the xref to the group.
The name of the xref to the user.
user
E-DOC-CTC-20071119-0014 v1.0
578
Download from Www.Somanuals.com. All Manuals Search And Download.
script Commands
E-DOC-CTC-20071119-0014 v1.0
582
Download from Www.Somanuals.com. All Manuals Search And Download.
script Commands
script add
Add line to script.
SYNTAX:
script add
name = <string>
[index = <number]>
command = <quoted string>
where:
name
Name of script.
REQUIRED
OPTIONAL
REQUIRED
index
Line number (0 = add).
Command.
command
E-DOC-CTC-20071119-0014 v1.0
584
Download from Www.Somanuals.com. All Manuals Search And Download.
script Commands
script delete
Delete complete script or line from script.
SYNTAX:
script delete
name = <{autopvc_add_qos|autopvc_delete_qos|
autopvc_add_bridge|autopvc_delete_pppoerelay|
autopvc_add_ipoa|autopvc_delete_ipoa|
autopvc_add_ethoa|autopvc_delete_ethoa|
autopvc_add_pppoa|autopvc_delete_pppoa|
autopvc_add_pppoe|autopvc_delete_pppoe|
autopvc_change_qos|wlbrintfadd|wlbrintfdel}>
[index = <number]>
where:
name
index
Name of script.
Line number.
REQUIRED
OPTIONAL
E-DOC-CTC-20071119-0014 v1.0
585
Download from Www.Somanuals.com. All Manuals Search And Download.
script Commands
script list
List script.
SYNTAX:
script list
[name = <{autopvc_add_qos|autopvc_delete_qos|
autopvc_add_bridge|autopvc_delete_pppoerelay|
autopvc_add_ipoa|autopvc_delete_ipoa|
autopvc_add_ethoa|autopvc_delete_ethoa|
autopvc_add_pppoa|autopvc_delete_pppoa|
autopvc_add_pppoe|autopvc_delete_pppoe|
autopvc_change_qos|wlbrintfadd|wlbrintfdel}]>
where:
name
Name of script.
OPTIONAL
E-DOC-CTC-20071119-0014 v1.0
587
Download from Www.Somanuals.com. All Manuals Search And Download.
script Commands
script run
Run script.
SYNTAX:
script run
name = <{autopvc_add_qos|autopvc_delete_qos|
autopvc_add_bridge|autopvc_delete_pppoerelay|
autopvc_add_ipoa|autopvc_delete_ipoa|
autopvc_add_ethoa|autopvc_delete_ethoa|
autopvc_add_pppoa|autopvc_delete_pppoa|
autopvc_add_pppoe|autopvc_delete_pppoe|
autopvc_change_qos|wlbrintfadd|wlbrintfdel}>
pars = <quoted string>
where:
name
pars
Name of script.
REQUIRED
REQUIRED
Parameters separated with comma e.q. a,b,c .
E-DOC-CTC-20071119-0014 v1.0
588
Download from Www.Somanuals.com. All Manuals Search And Download.
service Commands
service host add
Add a service.
SYNTAX:
service host add
name = <quoted string>
[mode = <{server|client|custom}]>
where:
name
mode
The name of the service.
REQUIRED
OPTIONAL
server, client or custom service ?
E-DOC-CTC-20071119-0014 v1.0
590
Download from Www.Somanuals.com. All Manuals Search And Download.
service Commands
service host assign
Assign a service to a host.
SYNTAX:
service host assign
name = <{ABC (Another Bittorent Client)|Age
of Empires|Age of Mythology|AIM BitTorrent|
Black and White|Call of Duty|Call of Duty
- UnitedOffensive|CarbonCopy32|Castle
Wolfenstein|Championship Manager 03-04|
Checkpoint FW1 VPN|Command and Conquer
Generals|Command and ConquerZero Hour|Counter
Strike|Cu-SeeMe Cornell|Cu-SeeMe White
Pine 3.1.2and 4.0|Dark Reign 2|Delta Force|
Destroyer Command|Diablo II|DirectConnect|
DirectX 7|DirectX 8|...}>
[host = <ip-address]>
[log = <{disabled|enabled}]>
where:
name
host
log
The name of the service.
The IP address of the host.
Enable/disable logging.
REQUIRED
OPTIONAL
OPTIONAL
E-DOC-CTC-20071119-0014 v1.0
591
Download from Www.Somanuals.com. All Manuals Search And Download.
service Commands
service host delete
Delete a service.
SYNTAX:
service host delete
name = <{ABC (Another Bittorent Client)|Age
of Empires|Age of Mythology|AIM BitTorrent|
Black and White|Call of Duty|Call of Duty
- UnitedOffensive|CarbonCopy32|Castle
Wolfenstein|Championship Manager 03-04|
Checkpoint FW1 VPN|Command and Conquer
Generals|Command and ConquerZero Hour|Counter
Strike|Cu-SeeMe Cornell|Cu-SeeMe White
Pine 3.1.2and 4.0|Dark Reign 2|Delta Force|
Destroyer Command|Diablo II|DirectConnect|
DirectX 7|DirectX 8|...}>
where:
name
The name of the service.
REQUIRED
E-DOC-CTC-20071119-0014 v1.0
592
Download from Www.Somanuals.com. All Manuals Search And Download.
service Commands
service host disable
Disable a service.
SYNTAX:
service host disable
[name = <{ABC (Another Bittorent Client)|
Age of Empires|Age of Mythology|BearShare|
BitTorrent|Black and White|Call of Duty|
Call of Duty -United Offensive|CarbonCopy32|
Castle Wolfenstein|ChampionshipManager 03-04|
Checkpoint FW1 VPN|Command and Conquer
Generals|Command and Conquer Zero Hour|
Counter Strike|Cu-SeeMe Cornell|Cu-SeeMe White
Pine 3.1.2 and 4.0|Dark Reign 2|Delta Force|
DestroyerCommand|Diablo II|Direct Connect|
DirectX 7|DirectX 8|...}]>
where:
name
The name of the service.
OPTIONAL
E-DOC-CTC-20071119-0014 v1.0
593
Download from Www.Somanuals.com. All Manuals Search And Download.
service Commands
service host list
Display list of services.
SYNTAX:
service host list
[name = <{ABC (Another Bittorent Client)|
Age of Empires|Age of Mythology|BearShare|
BitTorrent|Black and White|Call of Duty|
Call of Duty -United Offensive|CarbonCopy32|
Castle Wolfenstein|ChampionshipManager 03-04|
Checkpoint FW1 VPN|Command and Conquer
Generals|Command and Conquer Zero Hour|
Counter Strike|Cu-SeeMe Cornell|Cu-SeeMe White
Pine 3.1.2 and 4.0|Dark Reign 2|Delta Force|
DestroyerCommand|Diablo II|Direct Connect|
DirectX 7|DirectX 8|...}]>
where:
name
The name of the service.
OPTIONAL
E-DOC-CTC-20071119-0014 v1.0
595
Download from Www.Somanuals.com. All Manuals Search And Download.
service Commands
service host rule add
Create/define service portmap.
SYNTAX:
service host rule add
name = <{ABC (Another Bittorent Client)|Age
of Empires|Age of Mythology|AIM BitTorrent|
Black and White|Call of Duty|Call of Duty
- UnitedOffensive|CarbonCopy32|Castle
Wolfenstein|Championship Manager 03-04|
Checkpoint FW1 VPN|Command and Conquer
Generals|Command and ConquerZero Hour|Counter
Strike|Cu-SeeMe Cornell|Cu-SeeMe White
Pine 3.1.2and 4.0|Dark Reign 2|Delta Force|
Destroyer Command|Diablo II|DirectConnect|
DirectX 7|DirectX 8|...}>
[protocol = <{any|tcp|udp}]>
[baseport = <{at-echo|at-nbp|at-rtmp|at-zis|
auth|bgp|biff|bootpc|bootps|finger|ftp|ftp-
data|gopher|h323|httpproxy|ike|ils|imap2|
imap3|ingres-net|ipcserver|ipx|irc-o|irc-u|
kerberos|ldap|login|netbios-dgm|netbios-ns|
netbios-ssn|netwall|netware-ip|new-rwho|nfds|
nicname|nntp|ntalk|ntp|pcmail-srv|pop2|pop3|
printer|qotd|realaudio|rip|rtelnet|rtsp|sip|
smtp|snmp|snmptrap|snpp|sntp|sql*net|sql-
net|sqlserv|sunrpc|syslog|systat|talk|...}
ornumber]>
portrange = <port-range>
[triggerport = <{at-echo|at-nbp|at-rtmp|at-
zis|auth|bgp|biff|bootpc|bootps|finger|ftp|
ftp-data|gopher|h323|httpproxy|ike|ils|imap2|
imap3|ingres-net|ipcserver|ipx|irc-o|irc-u|
kerberos|ldap|login|netbios-dgm|netbios-ns|
netbios-ssn|netwall|netware-ip|new-rwho|nfds|
nicname|nntp|ntalk|ntp|pcmail-srv|pop2|pop3|
printer|qotd|realaudio|rip|rtelnet|rtsp|sip|
smtp|snmp|snmptrap|snpp|sntp|sql*net|sql-net|
sqlserv|sunrpc|syslog|systat|talk|...} or
number]>
[triggerprotocol = <{any|tcp|udp}]>
where:
name
The name of the service.
Protocol type.
REQUIRED
OPTIONAL
OPTIONAL
REQUIRED
protocol
baseport
portrange
Inbound base port.
The outbound portrange.
E-DOC-CTC-20071119-0014 v1.0
596
Download from Www.Somanuals.com. All Manuals Search And Download.
service Commands
triggerport
Defines outbound trigger port.
Protocol of the trigger port.
OPTIONAL
OPTIONAL
triggerprotocol
E-DOC-CTC-20071119-0014 v1.0
597
Download from Www.Somanuals.com. All Manuals Search And Download.
service Commands
service host rule delete
Delete a service portmap.
SYNTAX:
service host rule delete
name = <{ABC (Another Bittorent Client)|Age
of Empires|Age of Mythology|AIM BitTorrent|
Black and White|Call of Duty|Call of Duty
- UnitedOffensive|CarbonCopy32|Castle
Wolfenstein|Championship Manager 03-04|
Checkpoint FW1 VPN|Command and Conquer
Generals|Command and ConquerZero Hour|Counter
Strike|Cu-SeeMe Cornell|Cu-SeeMe White
Pine 3.1.2and 4.0|Dark Reign 2|Delta Force|
Destroyer Command|Diablo II|DirectConnect|
DirectX 7|DirectX 8|...}>
[protocol = <{any|tcp|udp}]>
[baseport = <{at-echo|at-nbp|at-rtmp|at-zis|
auth|bgp|biff|bootpc|bootps|finger|ftp|ftp-
data|gopher|h323|httpproxy|ike|ils|imap2|
imap3|ingres-net|ipcserver|ipx|irc-o|irc-u|
kerberos|ldap|login|netbios-dgm|netbios-ns|
netbios-ssn|netwall|netware-ip|new-rwho|nfds|
nicname|nntp|ntalk|ntp|pcmail-srv|pop2|pop3|
printer|qotd|realaudio|rip|rtelnet|rtsp|sip|
smtp|snmp|snmptrap|snpp|sntp|sql*net|sql-
net|sqlserv|sunrpc|syslog|systat|talk|...}
ornumber]>
portrange = <port-range>
[triggerport = <{at-echo|at-nbp|at-rtmp|at-
zis|auth|bgp|biff|bootpc|bootps|finger|ftp|
ftp-data|gopher|h323|httpproxy|ike|ils|imap2|
imap3|ingres-net|ipcserver|ipx|irc-o|irc-u|
kerberos|ldap|login|netbios-dgm|netbios-ns|
netbios-ssn|netwall|netware-ip|new-rwho|nfds|
nicname|nntp|ntalk|ntp|pcmail-srv|pop2|pop3|
printer|qotd|realaudio|rip|rtelnet|rtsp|sip|
smtp|snmp|snmptrap|snpp|sntp|sql*net|sql-net|
sqlserv|sunrpc|syslog|systat|talk|...} or
number]>
[triggerprotocol = <{any|tcp|udp}]>
where:
name
The name of the service.
Protocol type.
REQUIRED
OPTIONAL
OPTIONAL
REQUIRED
protocol
baseport
portrange
Inbound base port.
The outbound portrange.
E-DOC-CTC-20071119-0014 v1.0
598
Download from Www.Somanuals.com. All Manuals Search And Download.
service Commands
triggerport
Defines outbound trigger port.
Protocol of the trigger port.
OPTIONAL
OPTIONAL
triggerprotocol
E-DOC-CTC-20071119-0014 v1.0
599
Download from Www.Somanuals.com. All Manuals Search And Download.
service Commands
service system ifadd
Add an interface to the access list.
SYNTAX:
service system ifadd
name = <{PPTP|HTTP|HTTPs|FTP|TELNET|RIP-Query|
DNS-S|SNMP_AGENT|SSDP|MDAP|PING_RESPONDER}>
group = <{wan|local|lan|tunnel|dmz|guest} or
number>
where:
name
group
The name of the service for this access list.
The interface group for this access list.
REQUIRED
REQUIRED
E-DOC-CTC-20071119-0014 v1.0
602
Download from Www.Somanuals.com. All Manuals Search And Download.
service Commands
service system ifdelete
Delete an interface from the access list.
SYNTAX:
service system ifdelete
name = <{PPTP|HTTP|HTTPs|FTP|TELNET|RIP-Query|
DNS-S|SNMP_AGENT|SSDP|MDAP|PING_RESPONDER}>
group = <{wan|local|lan|tunnel|dmz|guest} or
number>
where:
name
group
The name of the service for this access list.
The interface group for this access list.
REQUIRED
REQUIRED
E-DOC-CTC-20071119-0014 v1.0
603
Download from Www.Somanuals.com. All Manuals Search And Download.
service Commands
service system ipadd
Add an ip address (range) to the access list.
SYNTAX:
service system ipadd
name = <{PPTP|HTTP|HTTPs|FTP|TELNET|RIP-Query|
DNS-S|SNMP_AGENT|SSDP|MDAP|PING_RESPONDER}>
ip = <ip-range>
where:
name
ip
The name of the service for this access list.
REQUIRED
REQUIRED
The ip address (range) for this access list.
E-DOC-CTC-20071119-0014 v1.0
604
Download from Www.Somanuals.com. All Manuals Search And Download.
service Commands
service system ipdelete
Delete an ip address (range) from the access list.
SYNTAX:
service system ipdelete
name = <{PPTP|HTTP|HTTPs|FTP|TELNET|RIP-Query|
DNS-S|SNMP_AGENT|SSDP|MDAP|PING_RESPONDER}>
ip = <ip-range>
where:
name
ip
The name of the service for this access list.
The ip address (range) for this access list.
REQUIRED
REQUIRED
E-DOC-CTC-20071119-0014 v1.0
605
Download from Www.Somanuals.com. All Manuals Search And Download.
service Commands
service system list
Display services.
SYNTAX:
service system list
[name = <{PPTP|PPTPD|PPTPGRE|SNTP|
SLA_ICMP_PING|SLA_UDP_PING|HTTP|HTTPs|RAD|
Dynamic DNS|dyndns|statdns|custom|No-IP|DtDNS|
gnudip|DHCP-S|DHCP-R|SNMP_AGENT|SSDP|MDAP|
CWMP-C|CWMP-S|RAS|SRAS|IP_COMMANDS|ICMP_PING|
SENDTO|PING_RESPONDER|ICMP_TRACEROUTE|
UDP_TRACEROUTE|HTTPPROBE}]>
[expand = <{disabled|enabled}]>
[dynamics = <{disabled|enabled}]>
[members = <{disabled|enabled}]>
where:
name
The name of the service.
Expanded listing.
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
expand
dynamics
members
Display dynamic sevices.
Display sevice group members.
E-DOC-CTC-20071119-0014 v1.0
606
Download from Www.Somanuals.com. All Manuals Search And Download.
service Commands
service system mapadd
Add a port map for a service.
SYNTAX:
service system mapadd
name = <{PPTP|HTTP|HTTPs|HTTPI|FTP|TELNET|DNS-
S|SNMP_AGENT|SSDP|MDAP}>
intf = <{loop|Internet|LocalNetwork}>
port = <{at-echo|at-nbp|at-rtmp|at-zis|auth|
bgp|biff|bootpc|bootps|chargen|data|gopher|
h323|httpproxy|ike|ils|imap2|imap3|ingres-
net|ipcserver|ipx|irc-o|irc-u|kerberos|ldap|
login|netbios-dgm|netbios-ns|netbios-ssn|
netwall|netware-ip|new-rwho|nfds|nicname|nntp|
ntalk|ntp|pcmail-srv|pop2|pop3|printer|qotd|
realaudio|rip|rtelnet|rtsp|sip|smtp|snmp|
snmptrap|snpp|sntp|sql*net|sql-net|sqlserv|
sunrpc|syslog|systat|talk|telnet|...} or
number>
where:
name
intf
The name of the service for this map.
The interface for this map.
The port for this map.
REQUIRED
REQUIRED
REQUIRED
port
E-DOC-CTC-20071119-0014 v1.0
607
Download from Www.Somanuals.com. All Manuals Search And Download.
service Commands
service system mapdelete
Delete a port map for a service.
SYNTAX:
service system mapdelete
name = <{PPTP|HTTP|HTTPs|HTTPI|FTP|TELNET|DNS-
S|SNMP_AGENT|SSDP|MDAP}>
intf = <{loop|Internet|LocalNetwork}>
port = <{at-echo|at-nbp|at-rtmp|at-zis|auth|
bgp|biff|bootpc|bootps|chargen|data|gopher|
h323|httpproxy|ike|ils|imap2|imap3|ingres-
net|ipcserver|ipx|irc-o|irc-u|kerberos|ldap|
login|netbios-dgm|netbios-ns|netbios-ssn|
netwall|netware-ip|new-rwho|nfds|nicname|nntp|
ntalk|ntp|pcmail-srv|pop2|pop3|printer|qotd|
realaudio|rip|rtelnet|rtsp|sip|smtp|snmp|
snmptrap|snpp|sntp|sql*net|sql-net|sqlserv|
sunrpc|syslog|systat|talk|telnet|...} or
number>
where:
name
intf
The name of the service for this map.
The interface for this map.
The port for this map.
REQUIRED
REQUIRED
REQUIRED
port
E-DOC-CTC-20071119-0014 v1.0
608
Download from Www.Somanuals.com. All Manuals Search And Download.
service Commands
service system modify
Modify a service.
SYNTAX:
service system modify
name = <{PPTP|PPTPD|PPTPGRE|SNTP|
SLA_ICMP_PING|SLA_UDP_PING|HTTP|HTTPs|RAD|
DHCP-S|DHCP-R|SNMP_AGENT|SSDP|MDAP|CWMP-C|
CWMP-S|RAS|SRAS|IP_COMMANDS|PING_RESPONDER}>
[state = <{disabled|enabled}]>
[port = <{at-echo|at-nbp|at-rtmp|at-zis|auth|
bgp|biff|bootpc|bootps|chargen|data|gopher|
h323|httpproxy|ike|ils|imap2|imap3|ingres-
net|ipcserver|ipx|irc-o|irc-u|kerberos|ldap|
login|netbios-dgm|netbios-ns|netbios-ssn|
netwall|netware-ip|new-rwho|nfds|nicname|nntp|
ntalk|ntp|pcmail-srv|pop2|pop3|printer|qotd|
realaudio|rip|rtelnet|rtsp|sip|smtp|snmp|
snmptrap|snpp|sntp|sql*net|sql-net|sqlserv|
sunrpc|syslog|systat|talk|telnet|...} or
number]>
[qoslabel = <{None|DSCP|Interactive|
Management|Video|VoIP-RTP|VoIP-Signal|
default}]>
[routelabel = <{None|DSCP|Interactive|
Management|Video|VoIP-RTP|VoIP-Signal|
default}]>
[srcintf = <{loop|Internet|LocalNetwork}]>
[log = <{disabled|enabled}]>
[forward = <{disabled|enabled}]>
[natpmweight = <number{0-255}]>
where:
name
The name of the service.
REQUIRED
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
state
Disable/Enable this service.
port
The port of the service.
qoslabel
routelabel
srcintf
QOS label for service data.
Route label for service data.
The primary ip interface for this service.
Disable/Enable service logging.
Disable/Enable service forwarding.
The nat portmap weight for this service.
log
forward
natpmweight
E-DOC-CTC-20071119-0014 v1.0
609
Download from Www.Somanuals.com. All Manuals Search And Download.
snmp Commands
E-DOC-CTC-20071119-0014 v1.0
610
Download from Www.Somanuals.com. All Manuals Search And Download.
snmp Commands
snmp community add
Config an SNMP community string to allow snmp access over IP.
SYNTAX:
snmp community add
securityname = <{RWCommunity|ROCommunity}>
communityname = <password>
where:
securityname
Configure access rights/restrictions control for
the community name.
REQUIRED
REQUIRED
communityname
Configure SNMP community name.
E-DOC-CTC-20071119-0014 v1.0
612
Download from Www.Somanuals.com. All Manuals Search And Download.
snmp Commands
snmp community delete
Delete an SNMP community string to prevent snmp access over IP.
SYNTAX:
snmp community delete
securityname = <{RWCommunity|ROCommunity}>
where:
securityname
Access rights/restrictions control of the
community name to be deleted.
REQUIRED
E-DOC-CTC-20071119-0014 v1.0
613
Download from Www.Somanuals.com. All Manuals Search And Download.
snmp Commands
snmp community modify
Modify an SNMP community string to allow snmp access over IP.
SYNTAX:
snmp community modify
securityname = <{RWCommunity|ROCommunity}>
communityname = <password>
where:
securityname
Configure access rights/restrictions control for
the community name.
REQUIRED
REQUIRED
communityname
Configure SNMP community name.
E-DOC-CTC-20071119-0014 v1.0
615
Download from Www.Somanuals.com. All Manuals Search And Download.
snmp Commands
snmp config
Configure global SNMP parameters.
SYNTAX:
snmp config
[sysContact = <quoted string]>
[sysName = <quoted string]>
[sysLocation = <quoted string]>
where:
sysContact
sysName
SNMP System Contact
SNMP System Name
SNMP System Location
OPTIONAL
OPTIONAL
OPTIONAL
sysLocation
E-DOC-CTC-20071119-0014 v1.0
616
Download from Www.Somanuals.com. All Manuals Search And Download.
snmp Commands
snmp get
Get from supplied object identity. e.g. get objectid=.1.3.6.1.2.1.1.1.0
SYNTAX:
snmp get
[objectid = <string]>
where:
objectid
Object identity to get from ... must include
the instance which is 0 for scalar objects
e.g. .1.3.6.1.2.1.1.1.0 sysDescription
OPTIONAL
E-DOC-CTC-20071119-0014 v1.0
617
Download from Www.Somanuals.com. All Manuals Search And Download.
snmp Commands
snmp getnext
Get next from supplied object identity. e.g. getnext objectid=
SYNTAX:
snmp getnext
[objectid = <string]>
where:
objectid
Object identity to getNext from e.g. .1.3.6.1.2.1.1
system returns sysDescription
OPTIONAL
E-DOC-CTC-20071119-0014 v1.0
618
Download from Www.Somanuals.com. All Manuals Search And Download.
snmp Commands
snmp ifadd
Create a new SNMP interface.
SYNTAX:
snmp ifadd
intf = <string>
dest = <{loop|ethif1|ethif2|ethif3|ethif4|
wlif1|ceoc|bridge|OBC|ethport1|Internet_ppp|
Internet|LocalNetwork}>
where:
intf
The name for the new SNMP interface.
REQUIRED
REQUIRED
dest
The destination interface for this SNMP
interface.
E-DOC-CTC-20071119-0014 v1.0
619
Download from Www.Somanuals.com. All Manuals Search And Download.
snmp Commands
snmp ifattach
Attach an SNMP interface.
SYNTAX:
snmp ifattach
intf = <{loop|ethif1|ethif2|ethif3|ethif4|
wlif1|ceoc|bridge|OBC|ethport1|Internet_ppp|
Internet|LocalNetwork}>
where:
intf
The name of the SNMP interface.
REQUIRED
E-DOC-CTC-20071119-0014 v1.0
620
Download from Www.Somanuals.com. All Manuals Search And Download.
snmp Commands
snmp ifconfig
Modify an SNMP interface.
SYNTAX:
snmp ifconfig
intf = <{loop|ethif1|ethif2|ethif3|ethif4|
wlif1|ceoc|bridge|OBC|ethport1|Internet_ppp|
Internet|LocalNetwork}>
[securityname = <{RWCommunity|ROCommunity}]>
[communityname = <password]>
where:
intf
The name of the SNMP interface to configure.
REQUIRED
OPTIONAL
securityname
Configure access rights/restrictions control for
the community name.
communityname
Configure SNMP community name.
OPTIONAL
E-DOC-CTC-20071119-0014 v1.0
621
Download from Www.Somanuals.com. All Manuals Search And Download.
snmp Commands
snmp ifdelete
Delete an SNMP interface.
SYNTAX:
snmp ifdelete
intf = <{loop|ethif1|ethif2|ethif3|ethif4|
wlif1|ceoc|bridge|OBC|ethport1|Internet_ppp|
Internet|LocalNetwork}>
where:
intf
The name of the SNMP interface.
REQUIRED
E-DOC-CTC-20071119-0014 v1.0
622
Download from Www.Somanuals.com. All Manuals Search And Download.
snmp Commands
snmp ifdetach
Detach an SNMP interface.
SYNTAX:
snmp ifdetach
intf = <{loop|ethif1|ethif2|ethif3|ethif4|
wlif1|ceoc|bridge|OBC|ethport1|Internet_ppp|
Internet|LocalNetwork}>
where:
intf
The name of the SNMP interface.
REQUIRED
E-DOC-CTC-20071119-0014 v1.0
623
Download from Www.Somanuals.com. All Manuals Search And Download.
snmp Commands
snmp iflist
Display the SNMP interfaces.
SYNTAX:
snmp iflist
[intf = <{loop|ethif1|ethif2|ethif3|ethif4|
wlif1|ceoc|bridge|OBC|ethport1|Internet_ppp|
Internet|LocalNetwork}]>
where:
intf
The name of an SNMP interface.
OPTIONAL
E-DOC-CTC-20071119-0014 v1.0
624
Download from Www.Somanuals.com. All Manuals Search And Download.
snmp Commands
snmp walk
Walk from supplied object identity. e.g. walk objectid=.1.3.6.1.2.1.1
SYNTAX:
snmp walk
[objectid = <string]>
where:
objectid
Object identity to walk from e.g. .1.3.6.1.2.1.1
system walks the system group
OPTIONAL
E-DOC-CTC-20071119-0014 v1.0
625
Download from Www.Somanuals.com. All Manuals Search And Download.
sntp Commands
E-DOC-CTC-20071119-0014 v1.0
626
Download from Www.Somanuals.com. All Manuals Search And Download.
sntp Commands
sntp add
Add NTP server
SYNTAX:
sntp add
[addr = <ip-address]>
[name = <string]>
[version = <number{1-4}]>
where:
addr
IP address of NTP server to be added to list
OPTIONAL
OPTIONAL
name
DNS name of NTP server to be added to list.
If both the IP address and the DNS name are
provided, the IP address is ignored.
version
SNTP version of server (1,2,3 or 4)
OPTIONAL
E-DOC-CTC-20071119-0014 v1.0
628
Download from Www.Somanuals.com. All Manuals Search And Download.
sntp Commands
sntp config
Modify/Display configuration
SYNTAX:
sntp config
[state = <{enabled|disabled}]>
[poll = <number{1-10080}]>
[pollpresync = <number{1-60}]>
where:
state
Enable/Disable SNTP client
OPTIONAL
OPTIONAL
OPTIONAL
poll
polling interval (1 min, ... ,10080min(=7days))
pollpresync
polling interval before first sync (1
min, ... ,60min)
E-DOC-CTC-20071119-0014 v1.0
629
Download from Www.Somanuals.com. All Manuals Search And Download.
sntp Commands
sntp delete
Delete NTP server from list
SYNTAX:
sntp delete
[addr = <ip-address]>
[name = <string]>
where:
addr
IP address of NTP server to be removed from list OPTIONAL
name
DNS name of NTP server to be removed from
list
OPTIONAL
E-DOC-CTC-20071119-0014 v1.0
631
Download from Www.Somanuals.com. All Manuals Search And Download.
software Commands
E-DOC-CTC-20071119-0014 v1.0
634
Download from Www.Somanuals.com. All Manuals Search And Download.
software Commands
software download
Download parameters.
SYNTAX:
software download
filetype = <{firmware|configuration}>
url = <string>
[username = <string]>
[password = <string]>
filesize = <string>
[targetfilename = <string]>
where:
filetype
url
The type of the file to be downloaded.
REQUIRED
REQUIRED
Set the HTTP URL where the file is to be found
including remote filename.
username
password
Set the name to be used to authenticate to the
download server.
OPTIONAL
OPTIONAL
Set the password the be used to authenticate to
the download server.
filesize
Set the size of the file to be downloaded.
REQUIRED
OPTIONAL
targetfilename
Set the filename used to save the file on the
modem.
E-DOC-CTC-20071119-0014 v1.0
636
Download from Www.Somanuals.com. All Manuals Search And Download.
system Commands
system config
Set or change system config parameters.
SYNTAX:
system config
[upnp = <{disabled|enabled}]>
[tr64 = <{disabled|enabled}]>
[mdap = <{disabled|enabled}]>
[led = <{green|red|orange|flash|off}]>
[resetbutton = <{disabled|enabled}]>
[digestauth = <{disabled|enabled}]>
[defaultconnection = <{loop|Internet|
LocalNetwork}]>
[autosave = <{enabled|disabled}]>
[autosavedelay = <number{0-600}]>
where:
upnp
Enable/Disable upnp discovery
Enable/Disable TR-64 discovery
Enable/Disable mdap discovery
Set system LED color
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
tr64
mdap
led
resetbutton
Enable/Disable reset-to-factory-defaults
pushbutton
digestauth
Enable/Disable HTTP digest authentication
The name of the default internet connection.
Enable/Disable autosaves
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
defaultconnection
autosave
autosavedelay
Autosave delay in seconds (0 for immediate
save)
E-DOC-CTC-20071119-0014 v1.0
640
Download from Www.Somanuals.com. All Manuals Search And Download.
system Commands
system dst
Set daylight saving values
SYNTAX:
system dst
[status = <{Disable|Enable}]>
[mode = <{Absolute|Relative}]>
[startdate = <dd/mm/yyyy]>
[starttime = <hh:mm:ss]>
[enddate = <dd/mm/yyyy]>
[endtime = <hh:mm:ss]>
[startweekday = <{Monday|Tuesday|Wednesday|
Thursday|Friday|Saturday|Sunday}]>
[starthour = <number{0-23}]>
[startweek = <number{1-5}]>
[startmonth = <number{1-12}]>
[endweekday = <{Monday|Tuesday|Wednesday|
Thursday|Friday|Saturday|Sunday}]>
[endhour = <number{0-23}]>
[endweek = <number{1-5}]>
[endmonth = <number{1-12}]>
where:
status
Set daylight saving status
Set daylight saving mode
OPTIONAL
mode
OPTIONAL
OPTIONAL
startdate
Set the start date of the daylight saving in the
absolute mode
starttime
enddate
Set the start time of the daylight saving in the
absolute mode
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
Set the end date of the daylight saving in the
absolute mode
endtime
Set the end time of the daylight saving in the
absolute mode
startweekday
starthour
startweek
startmonth
Set the start weekday of the daylight saving in
the relative mode
Set the start hour of the daylight saving in the
relative mode
Set the start week of the daylight saving in the
relative mode
Set the start month of the daylight saving in the
ralative mode
E-DOC-CTC-20071119-0014 v1.0
643
Download from Www.Somanuals.com. All Manuals Search And Download.
system Commands
endweekday
endhour
Set the end weekday of the daylight saving in
the relative mode
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
Set the end hour of the daylight saving in the
relative mode
endweek
Set the end week of the daylight saving in the
relative mode
endmonth
Set the end month of the daylight saving in the
relative mode
E-DOC-CTC-20071119-0014 v1.0
644
Download from Www.Somanuals.com. All Manuals Search And Download.
system Commands
system locale
Set/Get regional settings.
SYNTAX:
system locale
[dec_symbol = <{,|.}]>
[group_symbol = <{.|,}]>
[date_separator = <{/|-|.}]>
[date_format = <{iso|ddmmyyyy|ddmmyy|mmddyyyy|
mmddyy}]>
[time_format = <{iso|hmmss}]>
[datetime_format = <{iso|date+time|time
+date}]>
[duration_format = <{dhmmss|hmmss}]>
where:
dec_symbol
Set decimal symbol
Set digit grouping symbol
Set date separator
Set date format
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
group_symbol
date_separator
date_format
time_format
Set time format
datetime_format
duration_format
Set date-time format
Set duration format
E-DOC-CTC-20071119-0014 v1.0
646
Download from Www.Somanuals.com. All Manuals Search And Download.
system Commands
system ra config
Configure Remote assistance params.
SYNTAX:
system ra config
[secure = <{disabled|enabled}]>
[port = <number]>
[timeout = <number]>
where:
secure
port
Enable/Disable https.
OPTIONAL
OPTIONAL
OPTIONAL
Set destination port.
timeout
Set connection timeout in minutes.
E-DOC-CTC-20071119-0014 v1.0
647
Download from Www.Somanuals.com. All Manuals Search And Download.
system Commands
system reset
Reset to (factory or ISP) defaults: user specific settings will be cleared !
SYNTAX:
system reset
factory = <{yes|no}>
proceed = <{no|yes}>
where:
factory
Option to reset to factory
REQUIRED
REQUIRED
proceed
Confirmation for resetting the modem.
E-DOC-CTC-20071119-0014 v1.0
649
Download from Www.Somanuals.com. All Manuals Search And Download.
system Commands
system settime
Set/Get date, time, timezone, daylight savings time, uptime.
SYNTAX:
system settime
[time = <hh:mm:ss]>
[timezone = <(+ or -)hh:mm]>
[daylightsaving = <{disabled|enabled}]>
[geotimezonename = <quoted string]>
[rtc = <{disabled|enabled}]>
where:
time
Set the system time
OPTIONAL
timezone
Set the system timezone(-12:00...+14:00 / 15
minute resolution)
OPTIONAL
daylightsaving
geotimezonename
rtc
Enable/Disable daylight saving
OPTIONAL
OPTIONAL
OPTIONAL
Set the geographical timezone by name
Enable/Disable the real time clock
E-DOC-CTC-20071119-0014 v1.0
650
Download from Www.Somanuals.com. All Manuals Search And Download.
system Commands
system timedreboot
Set or change editing mode timed reboot
SYNTAX:
system timedreboot
[state = <{disabled|enabled}]>
[time = <number{0-983040}]>
[date = <string]>
where:
state
time
date
Enable/Disable timed reboot
OPTIONAL
OPTIONAL
OPTIONAL
Change default countdown time (Min).
Set date/time to reboot (DD/MM/YYYY/HH:MM).
E-DOC-CTC-20071119-0014 v1.0
651
Download from Www.Somanuals.com. All Manuals Search And Download.
systemlog Commands
E-DOC-CTC-20071119-0014 v1.0
652
Download from Www.Somanuals.com. All Manuals Search And Download.
systemlog Commands
systemlog send
Send messages to remote syslog server.
SYNTAX:
systemlog send
[fac = <{kern|user|mail|daemon|auth|syslog|
lpr|news|uucp|cron|security|ftp|local6|
local7}]>
[sev = <{emerg|alert|crit|err|warning|notice|
info|debug}]>
[hist = <{disabled|enabled}]>
dest = <ip-address>
where:
fac
Syslog facility level.
OPTIONAL
OPTIONAL
OPTIONAL
sev
hist
Syslog severity level.
Syslog display message history (over several
bootups)
dest
Remote syslog server destination: an ip-address. REQUIRED
E-DOC-CTC-20071119-0014 v1.0
655
Download from Www.Somanuals.com. All Manuals Search And Download.
systemlog Commands
systemlog show
Show messages in the syslog message buffer.
SYNTAX:
systemlog show
[fac = <{kern|user|mail|daemon|auth|syslog|
lpr|news|uucp|cron|security|ftp|local6|
local7}]>
[sev = <{emerg|alert|crit|err|warning|notice|
info|debug}]>
[hist = <{disabled|enabled}]>
where:
fac
Syslog facility level.
Syslog severity level.
OPTIONAL
OPTIONAL
OPTIONAL
sev
hist
Syslog display message history (over several
bootups)
E-DOC-CTC-20071119-0014 v1.0
656
Download from Www.Somanuals.com. All Manuals Search And Download.
tls Commands
tls acs-client cert list
List certificates
SYNTAX:
tls acs-client cert list
[index = <number]>
[expand = <{disabled|enabled}]>
where:
index
Certificate index
Display more information
OPTIONAL
OPTIONAL
expand
E-DOC-CTC-20071119-0014 v1.0
660
Download from Www.Somanuals.com. All Manuals Search And Download.
tls Commands
tls acs-client config
Display/modify tls settings
SYNTAX:
tls acs-client config
[state = <{disabled|enabled}]>
[auth-serv = <{disabled|enabled}]>
[valid-date = <{disabled|enabled}]>
[valid-domain = <{disabled|enabled}]>
where:
state
SSL/TLS client for ACS state
Request server authentication
Check certificate validity date
Check certificate domain
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
auth-serv
valid-date
valid-domain
E-DOC-CTC-20071119-0014 v1.0
661
Download from Www.Somanuals.com. All Manuals Search And Download.
tls Commands
tls https-server cert list
List certificates
SYNTAX:
tls https-server cert list
[index = <number]>
[expand = <{disabled|enabled}]>
where:
index
Certificate index
Display more information
OPTIONAL
OPTIONAL
expand
E-DOC-CTC-20071119-0014 v1.0
664
Download from Www.Somanuals.com. All Manuals Search And Download.
tls Commands
tls https-server config
Display/modify tls settings
SYNTAX:
tls https-server config
[state = <{disabled|enabled}]>
[auth-client = <{disabled|enabled}]>
[valid-date = <{disabled|enabled}]>
where:
state
SSL/TLS server for HTTPS state
Request client authentication
Check certificate validity date
OPTIONAL
OPTIONAL
OPTIONAL
auth-client
valid-date
E-DOC-CTC-20071119-0014 v1.0
665
Download from Www.Somanuals.com. All Manuals Search And Download.
tls Commands
tls self cert list
List certificates
SYNTAX:
tls self cert list
[index = <number]>
[expand = <{disabled|enabled}]>
where:
index
Certificate index
OPTIONAL
OPTIONAL
expand
Display more information
E-DOC-CTC-20071119-0014 v1.0
666
Download from Www.Somanuals.com. All Manuals Search And Download.
traceroute Command
traceroute Command
Send ICMP/UDP packets to trace the ip path.
SYNTAX:
traceroute
addr = <ip-address>
[count = <number{1-10}]>
[size = <number{1-20000}]>
[interval = <number{1000-60000}]>
[maxhops = <number{1-255}]>
[dstport = <number{1-65535}]>
[maxfail = <number{0-255}]>
[type = <{icmp|udp}]>
[utime = <{disabled|enabled}]>
where:
addr
The destination IP address.
REQUIRED
OPTIONAL
count
The number of times to reissue a traceroute
request with the same time to live.
size
The size of the packet payload.
OPTIONAL
OPTIONAL
OPTIONAL
interval
maxhops
The interval in milliseconds between packets.
The upper limit on the number of routers
through which a packet can pass.
dstport
maxfail
The UDP destination port number to send to.
OPTIONAL
OPTIONAL
The max number of consecutive timeouts
allowed before terminating a traceroute request.
type
The type of traceroute packet(s).
Display time in useconds.
OPTIONAL
OPTIONAL
utime
E-DOC-CTC-20071119-0014 v1.0
667
Download from Www.Somanuals.com. All Manuals Search And Download.
upgrade Commands
E-DOC-CTC-20071119-0014 v1.0
668
Download from Www.Somanuals.com. All Manuals Search And Download.
upgrade Commands
upgrade config
Change the upgrade daemon configuration
SYNTAX:
upgrade config
[state = <{disabled|enabled}]>
[protocol = <{tftp|ftp|http|https}]>
where:
state
The upgrade daemon state
OPTIONAL
OPTIONAL
protocol
The transfer protocol to be used for file
download
E-DOC-CTC-20071119-0014 v1.0
670
Download from Www.Somanuals.com. All Manuals Search And Download.
upgrade Commands
upgrade profile add
Add a new file profile description
SYNTAX:
upgrade profile add
extension = <{sts|ini|bin}>
[maxsize(KBytes) = <number]>
action = <{none|config_load|script_load|
reboot|upgrade}>
where:
extension
The extension of the new file profile
REQUIRED
maxsize(KBytes)
The maximum filesize (in KBytes) allowed for
files with the extension of this profile
OPTIONAL
action
The action to be done when the file with the
extension of this profile is downloaded
REQUIRED
E-DOC-CTC-20071119-0014 v1.0
673
Download from Www.Somanuals.com. All Manuals Search And Download.
upgrade Commands
upgrade profile delete
Delete a file profile description
SYNTAX:
upgrade profile delete
where:
extension = <{sts|ini|bin}>
extension
The extension of the file profile to be deleted
REQUIRED
E-DOC-CTC-20071119-0014 v1.0
674
Download from Www.Somanuals.com. All Manuals Search And Download.
upgrade Commands
upgrade profile modify
Modify a file profile description
SYNTAX:
upgrade profile modify
extension = <{sts|ini|bin}>
[maxsize(KBytes) = <number]>
action = <{none|config_load|script_load|
reboot|upgrade}>
where:
extension
The extension of the new file profile
REQUIRED
maxsize(KBytes)
The maximum filesize (in KBytes) allowed for
files with the extension of this profile
OPTIONAL
action
The action to be done when the file with the
extension of this profile is downloaded
REQUIRED
E-DOC-CTC-20071119-0014 v1.0
676
Download from Www.Somanuals.com. All Manuals Search And Download.
upgrade Commands
upgrade start
Start a new upgrade
SYNTAX:
upgrade start
protocol = <{tftp|ftp|http|https}>
[server = <string]>
[filename = <string]>
where:
protocol
server
The protocol to be used for the download
The server name or IP address
The file to be downloaded
REQUIRED
OPTIONAL
OPTIONAL
filename
E-DOC-CTC-20071119-0014 v1.0
677
Download from Www.Somanuals.com. All Manuals Search And Download.
upnp Commands
E-DOC-CTC-20071119-0014 v1.0
678
Download from Www.Somanuals.com. All Manuals Search And Download.
upnp Commands
upnp config
Config upnp parameter(s)
SYNTAX:
upnp config
[maxage = <number{60-999999}]>
[writemode = <{full|natonly|readonly}]>
[safenat = <{disabled|enabled}]>
[preferredaddresses = <string]>
where:
maxage
writemode
safenat
ssdp advertisements MAX-AGE (default = 1800)
Configuration access level for UPnP
OPTIONAL
OPTIONAL
OPTIONAL
Enable / disable check on safe nat entries
(limited to own host)
preferredaddresses
CSV list of preferred ip addresses for UPnP (1
per lan ip-interface)
OPTIONAL
E-DOC-CTC-20071119-0014 v1.0
680
Download from Www.Somanuals.com. All Manuals Search And Download.
user Commands
user add
Add a user.
SYNTAX:
user add
name = <string>
password = <password>
role = <>
[hash2 = <string]>
[descr = <quoted string]>
[defuser = <{disabled|enabled}]>
[defremadmin = <{disabled|enabled}]>
[deflocadmin = <{disabled|enabled}]>
where:
name
User name.
REQUIRED
REQUIRED
REQUIRED
OPTIONAL
OPTIONAL
OPTIONAL
password
role
User password.
Role name.
hash2
The MD5 hash.
descr
User description.
Set this user as the default user.
defuser
defremadmin
deflocadmin
Set this user as the default remote administrator. OPTIONAL
Set this user as the default local administrator.
OPTIONAL
E-DOC-CTC-20071119-0014 v1.0
684
Download from Www.Somanuals.com. All Manuals Search And Download.
user Commands
user config
Modify the user.
SYNTAX:
user config
name = <{Administrator|tech}>
[password = <password]>
[role = <]>
[descr = <quoted string]>
[defuser = <{disabled|enabled}]>
[defremadmin = <{disabled|enabled}]>
[deflocadmin = <{disabled|enabled}]>
where:
name
User name.
REQUIRED
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
password
role
User password.
Role name.
descr
User description.
defuser
Set this user as the default user.
defremadmin
deflocadmin
Set this user as the default remote administrator. OPTIONAL
Set this user as the default local administrator.
OPTIONAL
E-DOC-CTC-20071119-0014 v1.0
685
Download from Www.Somanuals.com. All Manuals Search And Download.
user Commands
user list
Display the users.
SYNTAX:
user list
[name = <{Administrator|tech}]>
[channel = <{ftp|telnet|http|mdap|serial}]>
[origin = <{lan|wan|local}]>
[secure = <{disabled|enabled}]>
where:
name
User name.
OPTIONAL
channel
origin
The selected channel.
The selected origin.
OPTIONAL
OPTIONAL
OPTIONAL
secure
The selected security level.
E-DOC-CTC-20071119-0014 v1.0
688
Download from Www.Somanuals.com. All Manuals Search And Download.
wireless Commands
E-DOC-CTC-20071119-0014 v1.0
690
Download from Www.Somanuals.com. All Manuals Search And Download.
wireless Commands
E-DOC-CTC-20071119-0014 v1.0
692
Download from Www.Somanuals.com. All Manuals Search And Download.
wireless Commands
wireless ifconfig
Configures wireless settings.
SYNTAX:
wireless ifconfig
[state = <{enabled|disabled}]>
[channel = <{auto|1|2|3|4|5|6|7|8|9|10|11|12|
13}]>
[ssid = <quoted string]>
[any = <{enabled|disabled}]>
[interop = <{802.11b|802.11b(legacy)/g|
802.11b/g|802.11g}]>
[frameburst = <{disabled|enabled}]>
where:
state
Interface operational status of wireless access
point
OPTIONAL
channel
ssid
Communication channel number
SSID
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
any
Make SSID public
Interoperability mode
Framebursting
interop
frameburst
E-DOC-CTC-20071119-0014 v1.0
695
Download from Www.Somanuals.com. All Manuals Search And Download.
wireless Commands
wireless macacl add
Add an ACL MAC entry
SYNTAX:
wireless macacl add
[ssid_id = <number{0-5}]>
hwaddr = <hardware-address>
permission = <{allow|deny}>
[name = <quoted string]>
where:
ssid_id
ssid id
OPTIONAL
REQUIRED
REQUIRED
OPTIONAL
hwaddr
permission
name
The Ethernet MAC address of the ACL entry
The action to be performed on ACL entry
The name of the station
E-DOC-CTC-20071119-0014 v1.0
696
Download from Www.Somanuals.com. All Manuals Search And Download.
wireless Commands
wireless macacl config
Access Control List configuration
SYNTAX:
wireless macacl config
[ssid_id = <number{0-5}]>
[control = <{lock|unlock|register}]>
[regtime = <number{15-3600}]>
where:
ssid_id
control
regtime
ssid id
OPTIONAL
OPTIONAL
OPTIONAL
Access Control List mode
Registration time
E-DOC-CTC-20071119-0014 v1.0
697
Download from Www.Somanuals.com. All Manuals Search And Download.
wireless Commands
wireless macacl delete
Delete an ACL MAC entry
SYNTAX:
wireless macacl delete
ssid_id = <number{0-5}>
hwaddr = <hardware-address>
where:
ssid_id
ssid id
hardware address of the ACL entry
REQUIRED
REQUIRED
hwaddr
E-DOC-CTC-20071119-0014 v1.0
698
Download from Www.Somanuals.com. All Manuals Search And Download.
wireless Commands
wireless macacl flush
Flushes ACL entries
SYNTAX:
wireless macacl flush
[ssid_id = <number{0-5}]>
proceed = <{disabled|enabled}>
where:
ssid_id
ssid id
Confirmation required
OPTIONAL
REQUIRED
proceed
E-DOC-CTC-20071119-0014 v1.0
699
Download from Www.Somanuals.com. All Manuals Search And Download.
wireless Commands
wireless macacl modify
Modify an ACL entry
SYNTAX:
wireless macacl modify
ssid_id = <number{0-5}>
hwaddr = <hardware-address>
[permission = <{allow|deny}]>
[name = <quoted string]>
where:
ssid_id
ssid id
REQUIRED
REQUIRED
OPTIONAL
OPTIONAL
hwaddr
permission
name
The Ethernet MAC address of the ACL entry
The action to be performed on ACL entry
The name of the station
E-DOC-CTC-20071119-0014 v1.0
701
Download from Www.Somanuals.com. All Manuals Search And Download.
wireless Commands
wireless macacl register
Start a registration process (only for register mode)
SYNTAX:
wireless macacl register
proceed = <{disabled|enabled}>
where:
proceed
Confirmation required
REQUIRED
E-DOC-CTC-20071119-0014 v1.0
702
Download from Www.Somanuals.com. All Manuals Search And Download.
wireless Commands
wireless mssid ifconfig
Configure a ssid context
SYNTAX:
wireless mssid ifconfig
ssid_id = <number{0-5}>
[ssid = <string]>
[apisolation = <{disabled|enabled}]>
[any = <{disabled|enabled}]>
[secmode = <{disable|wep|wpa-psk}]>
[WEPkey = <quoted string]>
[WPAPSKkey = <quoted string]>
[WPAPSKversion = <{WPA|WPA2|WPA+WPA2}]>
[addscript = <quoted string]>
[delscript = <quoted string]>
[trace = <{disabled|enabled}]>
where:
ssid_id
ssid
ssid id
REQUIRED
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
ssid
apisolation
any
ap isolation
public network
security mode
secmode
WEPkey
WEP key: expected format 5 or 13 ASCII
characters, or 10 or 26 HEX digits.
WPAPSKkey
WPA-PSK key: expected format 8 to 63 ASCII
characters or 64 HEX digits.
OPTIONAL
WPAPSKversion
addscript
delscript
wpa version
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
creation data interfaces
remove data interfaces
security tracing
trace
E-DOC-CTC-20071119-0014 v1.0
705
Download from Www.Somanuals.com. All Manuals Search And Download.
wireless Commands
wireless multiuni add
add a multicast to unicat mapping
SYNTAX:
wireless multiuni add
multicast = <hardware-address>
unicast = <hardware-address>
where:
multicast
unicast
Multicast MAC
Unicast MAC
REQUIRED
REQUIRED
E-DOC-CTC-20071119-0014 v1.0
709
Download from Www.Somanuals.com. All Manuals Search And Download.
wireless Commands
wireless multiuni scanresults
display detected multicast mac addresses
SYNTAX:
wireless multiuni scanresults [rescan = <{no|yes}]>
where:
rescan
rescan for new multicast addresses
OPTIONAL
E-DOC-CTC-20071119-0014 v1.0
713
Download from Www.Somanuals.com. All Manuals Search And Download.
wireless Commands
wireless qos apacconfig
configure AP EDCA parameters
SYNTAX:
wireless qos apacconfig
[class = <{AC_BE|AC_BK|AC_VI|AC_VO}]>
[cwmax = <{1|3|7|15|31|63|127|255|511|1023|
2047|4095|8191|16383|32767}]>
[cwmin = <{0|1|3|7|15|31|63|127|255}]>
[aifsn = <number{1-15}]>
[txop = <number]>
where:
class
AC class
OPTIONAL
cwmax
cwmin
aifsn
CWmax configuration
CWmin configuration
Aifsn configuration
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
txop
txoplimit [us] configuration
E-DOC-CTC-20071119-0014 v1.0
714
Download from Www.Somanuals.com. All Manuals Search And Download.
wireless Commands
wireless qos staacconfig
configure STA EDCA parameters
SYNTAX:
wireless qos staacconfig
[class = <{AC_BE|AC_BK|AC_VI|AC_VO}]>
[cwmax = <{1|3|7|15|31|63|127|255|511|1023|
2047|4095|8191|16383|32767}]>
[cwmin = <{0|1|3|7|15|31|63|127|255}]>
[aifsn = <number{1-15}]>
[txop = <number]>
where:
class
AC class
OPTIONAL
cwmax
cwmin
aifsn
CWmax configuration
CWmin configuration
Aifsn configuration
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
txop
txoplimit [us] configuration
E-DOC-CTC-20071119-0014 v1.0
716
Download from Www.Somanuals.com. All Manuals Search And Download.
wireless Commands
wireless secmode wep
Configure WEP settings.
SYNTAX:
wireless secmode wep
where:
[encryptionkey = <quoted string]>
encryptionkey
WEP key: expected format 5 or 13 ASCII
characters, or 10 or 26 HEX digits.
OPTIONAL
E-DOC-CTC-20071119-0014 v1.0
719
Download from Www.Somanuals.com. All Manuals Search And Download.
wireless Commands
wireless secmode wpa-psk
Configure WPA-PSK settings.
SYNTAX:
wireless secmode wpa-psk
[presharedkey = <quoted string]>
[version = <{WPA|WPA2|WPA+WPA2}]>
where:
presharedkey
WPA-PSK key: expected format 8 to 63 ASCII
characters or 64 HEX digits.
OPTIONAL
OPTIONAL
version
wpa version
E-DOC-CTC-20071119-0014 v1.0
720
Download from Www.Somanuals.com. All Manuals Search And Download.
wireless Commands
wireless stations list
List of the currently associated stations
SYNTAX:
wireless stations list
[hwaddr = <hardware-address]>
[ssid_id = <number{0-5}]>
where:
hwaddr
ssid_id
The MAC address of station
Selected BSS
OPTIONAL
OPTIONAL
E-DOC-CTC-20071119-0014 v1.0
721
Download from Www.Somanuals.com. All Manuals Search And Download.
wireless Commands
wireless wds add
add WDS station
SYNTAX:
wireless wds add
bssid = <hardware-address>
[name = <quoted string]>
where:
bssid
name
The WDS bssid
REQUIRED
OPTIONAL
A user specified reference name
E-DOC-CTC-20071119-0014 v1.0
722
Download from Www.Somanuals.com. All Manuals Search And Download.
xdsl Commands
E-DOC-CTC-20071119-0014 v1.0
728
Download from Www.Somanuals.com. All Manuals Search And Download.
xdsl Commands
xdsl config
Modify/Display dsl configuration
SYNTAX:
xdsl config
[adslmultimode = <{adsl|adsl2|adsl2plus}]>
[detect-lop = <{disabled|enabled}]>
[syslog = <{disabled|enabled}]>
where:
adslmultimode
Set/Show selected multimode type of the
modem
OPTIONAL
detect-lop
syslog
Detect Loss Of Power
OPTIONAL
OPTIONAL
Log in syslog during showtime
E-DOC-CTC-20071119-0014 v1.0
730
Download from Www.Somanuals.com. All Manuals Search And Download.
xdsl Commands
xdsl debug multimode
Config custom multimode
SYNTAX:
xdsl debug multimode
[config = <[+/-]flag[+/-flag...]{default
t1.413issue2 g992.1_annex_a g992.2
g992.5_annex_m}]>
where:
config
The custom multimode bitmap
OPTIONAL
E-DOC-CTC-20071119-0014 v1.0
735
Download from Www.Somanuals.com. All Manuals Search And Download.
xdsl Commands
xdsl debug traceconfig
Config the adsl tracelevel
SYNTAX:
xdsl debug traceconfig
where:
level = <{0|1|2|3|4}>
level
Trace Level (0=disable tracing; 1=enable dsl
manager tracing; 2=enable dsl driver tracing)
REQUIRED
E-DOC-CTC-20071119-0014 v1.0
736
Download from Www.Somanuals.com. All Manuals Search And Download.
xdsl Commands
xdsl info
Displays status information about modem
SYNTAX:
xdsl info
[expand = <{disabled|enabled}]>
[g.997.1 = <{disabled|enabled}]>
[counter_period_filter = <{current|15_minutes|
24_hours}]>
[counters_reset = <{no|yes}]>
where:
expand
Condensed / Expanded listing link information
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
g.997.1
Condensed / Expanded listing link information
Specify the statistics period
counter_period_filter
counters_reset
Reset all counters
E-DOC-CTC-20071119-0014 v1.0
737
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
THOMSON Telecom Belgium
Prins Boudewijnlaan 47
www.thomson-broadband.com
© 2007 Thomson. All rights reserved.
E-DOC-CTC-20071119-0014 v1.0
Download from Www.Somanuals.com. All Manuals Search And Download.
|