POWER REQUIREMENTS
•Utilizes standard 9V alkaline battery (not included).To install,simply remove battery door.
(NOTE:The Input activates battery.To conserve energy, unplug when not in use.)
Power Consumption: approx.4mA.
•USE DC POWER SUPPLYONLY!
DC Power Supply Specifications:
Failure to do so may damage the unit and void warranty.
-9V DC regulated or unregulated,100mA minimum;
-2.1mm female plug,center negative (-).
•Optional factory po wer supply is available , Model #DC2.
WARNINGS:
• Attempting to repair unit is not recommended and may void warranty.
• Missing or altered serial numbers automatically void warranty. For your own protection,be sure
serial number labels on the unit’s back plate and exterior box are intact.
ONE YEAR LIMITED WARRANTY . PROOF OF PURCHASE REQUIRED
.
Manufacturer warrants unit to be free from defects in materials and workmanship for one (1) year
from date of purchase to the original purchaser and is not transferable.This warranty does not include
damage resulting from accident,misuse, abuse, alteration,or incorrect current or voltage. If unit be-
comes defective within warranty period, Tech 21 will elect to repair or replace it free of charge.After
warranty expires,Tech 21 will repair defective unit for a fee.
ALL REPAIRS for residents of U.S.Call Tech 21 for Return Authorization Number
. Manufacturer
will not accept packages without prior authorization,pre-paid freight (UPSpreferred) and proper insur-
ance. International purchasers should contact the authorizedTech 21 distributor in their particular
country.
FOR PERSONAL ASSISTANCE & SERVICE:
Contact Tech 21,Inc., weekdays from 9:00 AM to 5:00 PM,EST.
OWNER’S MANUAL
DESIGNED AND MANUF ACTURED IN THE U.S.A.
© 1993 Tech 21,Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
UNIVERSAL OUTPUT
Another aspect of the technological advancement of SansAmp, is a single output that is physically com-
patible for an y application.SansAmp’s Universal Output makes it possible to use the same output with
the following:
FULL RANGE(HiFi):
Tape
LIMITED RANGE (LoFi):
Rack Systems
Studio Monitors
P.A.
Stereo
Pre-Amps
Head &Cabinet
Combos
Practice Amps
OTHER INSTRUMENTS & APPLICATIONS
Be creative! SansAmp GT2 is not just for guitar.Try other instruments:bass, keyboards,drums,sax,
vocals,etc. (Just remember to be aware of the input signal level as noted previously.) Also try using
SansAmp GT2 in other applications,such as in mixdowns to liven up existing tracks.
For experimentation,start with a clean,flat setting:
•Set all 3 Character Switches at the bottom position.
•Set Knob Controls: Low and High at 11 o’clock
Drive and Level at 12 o’clock
Adjust EQ and gain structure to taste.
NOTEWORTHY NOTES & SUGGESTIONS
1. SansAmp GT2 is an interactive tool.It will react differently to various signal levels,as well as your
individual touch. For instance, a hotter signal and a heavy hand will increase the gain structure and result
in more overdrive.A cooler signal and a light touch decreases gain structure for a cleaner sound.
2. SansAmp GT2 has a very low noise level.If you experience noise, be aware of the following:
-SansAmp GT2 may be amplifying noise emanating from the input source.
-Check for pickup interference by moving guitar or turning the volume off.NOTE:Single coil pic-
ups are much more likely to generate hum;and on-board active electronics have a tendency to
create hiss.
-As with the use of any tube amplifier or electronic device, particularly in high gain settings, you may
be getting outside interference caused by lights,transformers,etc.
-Be conscious of how the controls of SansAmp GT2 interact.They are atypically sensitive.You need
not set everything at max to get maximum results.
3. The Input activates the battery. Don’t forget to unplug or you will waste your battery.The highly effi-
cient,low power consuming LED will fade as battery runs low (<6.5V).While SansAmp GT2 will contin-
ue to operate, we recommend replacing the battery at this time.
4. Buffered bypass ensures no high frequency signal loss through long cable lengths.
PLACEMENT ORDER OF OTHER EFFECTS
Place the following effects BEFORE SansAmp GT2:
Compression,Wah-wah,Envelope Filter
Place the following effects AFTER SansAmp GT2:
Chorus,Delay, EQ,Pitch Shifter, Reverb
®Registered trademarks of their respective companies.
Names of sample settings are intended for descriptive purposes only and
should not be construed as an endorsement or affiliation with the companies or artists named.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|