9A10303900
Z
-
CD X9
Micro Hi-Fi System
OWNER’S MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
This product has been designed and manufactured according to
FDA regulations “title 21, CFR, chapter 1, subchapter J, based on
the Radiation Control for Health and Safety Act of 1968“, and is
classified as class 1 laser product. There is not hazardous invisible
laser radiation during operation because invisible laser radiation
emitted inside of this product is completely confined in the
protective housings.
WARNING : TO PREVENT FIRE OR SHOCK
HAZARD, DO NOT EXPOSE THIS APPLIANCE
TO RAIN OR MOISTURE.
CAUTION
< DO NOT REMOVE THE EXTERNAL CASES OR CABINETS TO
EXPOSE THE ELECTRONICS. NO USER SERVICEABLE PARTS
ARE WITHIN!
The label required in this regulation is shown ①.
< IF YOU ARE EXPERIENCING PROBLEMS WITH THIS PRODUCT,
CONTACT TEAC FOR A SERVICE REFERRAL. DO NOT USE THE
PRODUCT UNTIL IT HAS BEEN REPAIRED.
For U.S.A.
①
< USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF
PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY
RESULT IN HAZARDOUS RADIATION EXPOSURE.
For U.S.A.
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following
measures:
Rear panel of the Subwoofer
Optical pickup:
Type
:
CMS-M95BG6
Manufacturer : Samsung Electro-Mechanics
Laser output
Wavelength
:
:
Less than 0.5 mW on the objective lens
760 - 800 nm
• Reorient or relocate the equipment and/or the receiving
antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician
for help.
CAUTION
Changes or modifications to this equipments not expressly
approved by TEAC CORPORATION for compliance will void the
user’s warranty.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Before Using the Unit
Thank you for choosing TEAC. Read this manual carefully
to get the best performance from this unit.
Read this before operation
< As the unit may become warm during operation, always leave
sufficient space around the unit for ventilation.
The ventilation holes should not be covered. Make sure there
is at least 20 cm of space above and at least 5 cm of space on
each side of the unit. Do NOT place anything on top of the
unit.
Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Before Using the Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Discs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
< The voltage supplied to the unit should match the voltage as
printed on the rear panel of the supplied subwoofer. If you
are in any doubt regarding this matter, consult an electrician.
Connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Wall Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Names of Each Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Remote Control Unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
< Choose the installation location of your unit carefully. Avoid
placing it in direct sunlight or close to a source of heat. Also
avoid locations subject to vibrations and excessive dust, heat,
cold or moisture.
Basic Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Listening to CD/MP3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Search Mode (MP3 only). . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Programmed Playback. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Repeat Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Shuffle Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Listening to an External Source . . . . . . . . . . . . . . . . . . . . . . . . 16
< Do not place the unit on an amplifier/receiver or any other
electronic device that generates heat.
< Do not open the sealed cabinet as this might result in damage
to the circuitry or electrical shock. If a foreign object should
get inside the unit, contact your dealer or service agency.
< When removing the power plug from the wall outlet, always
pull directly on the plug, never yank the cord.
Listening to the Radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Preset Tuning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
< To keep the laser pickup clean, do not touch it, and always
close the CD door.
Setting the Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Setting the Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
< Do not attempt to clean the unit with chemical solvents as
this might damage the finish. Use a clean, dry cloth.
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
< Keep this manual in a safe place for future reference.
DO NOT MOVE THE UNIT DURING PLAYBACK
During playback, the disc rotates at high speed. Do NOT lift or
move the unit during playback. Doing so may damage the
disc or the laser assembly.
WHEN MOVING THIS UNIT
When relocating or packing the unit for moving, be sure to
remove the disc. Moving this unit with the disc loaded may
result in damage to this unit.
CAUTION
The product shall not be exposed to dripping or splashing and
that no object filled with liquids, such as vases, shall be placed
on the product.
Do not install this equipment in a confined space such as a
book case or similar unit.
trademark of New Transducers Ltd.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Discs
Discs which can be played on this unit:
< CD-R and CD-RW discs are more sensitive to the effects of
heat and ultraviolet rays than ordinary CDs. It is important
that they are not stored in a location where direct sunlight
will fall on them, and away from sources of heat such as
radiators or heat-generating electrical devices.
• Conventional audio CDs bearing the COMPACT DISC
DIGITAL AUDIO logo on the label:
< Printable CD-R and CD-RW discs aren’t recommended, as the
• Properly finalized CD-R and CD-RW discs
label side might be sticky and damage the unit.
< Do not stick papers or protective sheets on the discs and do
Note:
not use any protective coating spray.
< Depending on the quality of the disc and/or the condition of
the recording, some CD-R/CD-RW discs may not be playable.
< Use a soft oil-based felt-tipped pen to write the information
on the label side. Never use a ball-point or hard-tipped pen,
as this may cause damage to the recorded side.
< Copy-protected discs and other discs that do not conform to
the CD standard may not play back correctly in this player. If
you use such discs in this unit, TEAC Corporation and its
subsidiaries cannot be responsible for any consequences or
guarantee the quality of reproduction. If you experience
problems with such non-standard discs, you should contact
the producers of the disc.
< Never use a stabilizer. Using commercially available CD
stabilizers with this unit will damage the mechanisms and
cause them to malfunction.
< Do not use CDs with an irregular shape (octagonal, heart
shaped, business card size, etc.). CDs of this sort can damage
the unit:
< Always place the disc on the disc tray with the label side up.
(Compact discs can be played or recorded only on one side.)
< To remove a disc from its storage case, press down on the
center of the case and lift the disc out, holding it carefully by
the edges.
< If you are in any doubt as to the care and handling of a CD-R/
CD-RW disc, read the precautions supplied with the disc, or
contact the disc manufacturer directly.
MP3 compatibility
< File names of MP3 should be alphanumeric characters. This
unit cannot display symbols and full-size or 2 bytes-wide
characters (such as Japanese, Chinese, etc.) correctly. Also, be
sure to use the file extension “.mp3”.
How to remove the disc
How to hold the disc
< Should the disc become dirty, wipe the surface radially (from
the center hole outward towards the outer edge) with a soft,
dry cloth:
< The disc must be finalized in order to play.
< The CD-ROM must be ISO 9660 compatible.
< When more than 200 files or folders are recorded on the disc,
the unit might not be able to play it correctly.
< Never use such chemicals as record sprays, antistatic sprays or
fluid, benzine or thinner to clean the discs. Such chemicals
will do irreparable damage to the disc’s plastic surface.
< Mono or stereo MPEG-1 Audio Layer 3 format, 44.1 or
48 kHz, fixed bit-rate.
< Discs should be returned to their cases after use to avoid dust
and scratches that could cause the laser pickup to “skip.”
< Audio encoded at 128 Kbps should sound close to regular
audio CD quality. Although this player will play lower bit-rate
MP3 tracks, the sound quality becomes noticeably worse at
lower bit-rates.
< Do not expose discs to direct sunlight or high humidity and
temperature for extended periods. Long exposure to high
temperatures will warp the disc.
< Do not play any disc that is warped, deformed or damaged.
Playing such discs may cause irreparable harm to the playing
mechanisms.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Connection
Speaker (R)
Speaker (L)
D
B
A
F
E
C
Side panel of
the main unit
Subwoofer
CAUTION
B
FM antenna
< Turn off the power of all the equipment before making
While in FM mode, tune in an FM station and extend the
lead to find the best position for reception. This antenna
may need to be repositioned if you move your unit to a new
location.
connections.
< Read instructions of each component you intend to use with
this unit.
< Be sure to insert each plug securely. To prevent hum and
noise, do not bundle the connection cords with the power
cord.
FM Outdoor Antenna
In an area where FM signals are weak, it will be necessary to
use a 75-ohm unbalanced-type outdoor FM antenna using
an optional (not supplied) matching transformer connected
to an external antenna. Generally, a 3-element antenna will
be sufficient; if you live in an area where the FM signals are
particularly weak, it may be necessary to use one with 5 or
more elements.
A
AM loop antenna
Position the antenna for the best sound.
If you want, you can hook the AM antenna on a wall as
shown below:
Outdoor FM Antenna (75Ω)
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Wall Mounting
You can mount the main unit and/or the left and right speakers
on a wall.
C
Subwoofer
Connect the TO SUBWOOFER and the FROM MAIN sockets
using the supplied cable.
Make sure to align the 5 mark on the connector with the
5 mark of the TO SUBWOOFER socket.
Precautions
< Be aware that the length of the cables are approximately 3 m.
Do not attempt to mount the main unit and the speakers too
far from the subwoofer.
D
SPEAKERS
< Drill holes into solid wall support, such as wooden frame or
Connect the left speaker’s plug to L, and the right speaker’s
plug to R.
concrete wall.
< TEAC supplies these brackets as a convenience to the product
owner. Consult your local building codes and exercise all
necessary caution when mounting these brackets. If you are
unsure how to use the supplied brackets, consult with a local
tradesmen or building supply expert.
< If not using the included speakers, make sure the speakers
you use are at least 4 Ω impedance.
< Do not connect anything other than speakers to these
terminals.
E
AC Power Cord
To hook on the wall
Be sure to connect the power cord to an AC outlet which
supplies the correct voltage.
1
Use the supplied template to determine drilling points.
2
Secure the brackets on the wall using the supplied screws.
Hold the power plug when plugging or unplugging the
power cord. Never pull or yank on the power cord.
< As a convenience, a set of tapered plastic anchors is supplied.
If you chose to use these anchors, drill a pilot hole using a
6mm drill bit then tap the anchor into the pilot hole.
Only use these anchors if they are appropriate for the
materials onto which the unit is to be mounted. Consult your
local hardware store if you are uncertain.
F
POWER switch of the Subwoofer
Use this switch to turn the system on or off.
The equipment draws a nominal amount of power from
the AC outlet even with its POWER switch in the OFF
position.
Note:
Before going on, make connections between the main unit
and the speakers by referring to page 6.
< If the power switch of the subwoofer turned off, the
settings kept in memory (clock, preset stations, timer
setting) will be erased.
3
Hang the main unit and/or the speakers to the mounting
tabs.
To avoid loosing your settings, it is advisable to keep this
switch ON when not in use.
G
AUX IN
Main Unit
Speaker
You can connect a portable audio player to this jack.
Connect the LINE OUT or PHONES jack (audio output jack)
of the player using the supplied stereo mini plug cable.
3
3
When using the PHONES jack of your mini player, you must
adjust the volume of the mini-player or you may hear no
sound from your CD-X9.
2
2
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Names of Each Control
G
E
K
M
H
F
R
J
S
D
T
N
U
C
O
L
A
B
C
M
N
P
B
Q
D E F G
H I
J
A
B
C
F
Remote Sensor
FUNCTION
When operating the remote control unit, point it towards
here.
Use this button to select a source (CD, AUX or TUNER).
G
STANDBY/ON
VOLUME
Press this switch to turn the unit on or off (standby).
The main unit is powered via the subwoofer. You need to first
turn on the subwoofer.
Press the up “+” or the down “–” button to adjust the
volume.
When the main unit is in the standby mode, the power
indicator of the Subwoofer is red.
When the unit is turned on, the indicator turns blue.
MEMORY/TIME SET
In CD mode, use this button to program tracks.
In TUNER mode, use this button to store preset channels into
memory.
This button is also used for clock adjustment.
The equipment draws a nominal amount of power from the
AC outlet even with its STANDBY/ON switch in the
STANDBY position.
D
FM MODE/MP3
In FM TUNER mode, use this button to select stereo or
monaural.
H
I
PLAY/PAUSE (y/J)
During playback of a MP3 disc, use this button to search track
name.
During playback of CD, use this button to switch the ESP
function on or off.
Use this button to start or pause playback of CD/MP3.
OPEN/CLOSE
Use this button to open and close the CD door.
E
FM/AM
Use this button to select AM or FM.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Control Unit
The provided Remote Control Unit allows the unit to be operated
from a distance.
When operating the remote control unit, point it towards the
remote sensor on the front panel of the unit.
J
SKIP (.//) / TUNING
In CD mode, momentarily press this button to skip tracks.
Hold down this button to search for a part of a track.
In TUNER mode, momentarily press this button to tune in
stations.
In Standby mode, these buttons are used to set or adjust the
clock and the timer.
< Even if the remote control unit is operated within the effective
range, remote control operation may be impossible if there
are any obstacles between the unit and the remote control.
K
L
CD door
Display
< If the remote control unit is operated near other products
which generate infrared rays, or if other remote control
devices using infrared rays are used near the unit, it may
operate incorrectly. Conversely, the other products may also
operate incorrectly.
M
STOP (H)
Use this button to stop playback of CD/MP3.
N
O
REPEAT
In CD mode, use this button for repeat playback.
Battery Installation
1
TIMER
Use this button together with the SKIP buttons to set the
timer.
P
Q
R
BASS
Use these buttons to adjust the bass sound up or down.
2
3
TREBLE
Use these buttons to adjust the treble sounds up and down.
MP3 FOLDER/PRESET
In TUNER mode, use this button to select preset stations.
During playback of a MP3 disc, use this button to select a
folder in the disc.
S
T
SLEEP
Use this button to set sleep timer.
1
2
3
Remove the battery compartment cover.
Put in the lithium battery (CR2032, 3V).
Close the cover.
SHUFFLE
Use this button for shuffle playback.
U
MUTING
Use this button to mute the sound.
Battery Replacement
If the distance required between the remote control unit and
main unit decreases, the battery is exhausted. In this case,
replace the battery with a new one.
Note:
To simplify explanations, instructions in this manual refer to
the names of the buttons and controls on the front panel
only. Associated controls on the remote control will also
operate similarly.
Precautions concerning batteries
Do not heat or disassemble batteries and never dispose of old
batteries by throwing them in a fire.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operation
(Rear panel of the subwoofer)
Headphones
For private listening, first reduce the volume level to
minimum. Then insert the plug from your headphones into
the PHONES jack, and adjust the volume using the VOLUME
buttons. The sound from the speakers is cut off while the
headphone jack is inserted.
1
4
3 2
1
2
Turn on the subwoofer.
Press the STANDBY/ON switch on the main unit.
CAUTION
Always lower the volume level prior to plugging in your
headphones. TO AVOID DAMAGING YOUR HEARING - Do
not place your headphones on your head until after you have
plugged them in.
3
4
Select a source by pressing the FUNCTION button.
Sleep Timer
Repeatedly pressing the SLEEP button permits setting an
interval (from 90 down to 10 minutes) after which you want
the unit to automatically turn off and shift into Standby
mode.
Play the source and adjust the volume using the
VOLUME buttons.
Each press of the SLEEP button changes the time indication by
10 minutes.
Muting
To mute the sound temporarily, press the MUTING button.
Press the MUTING button again to restore the sound.
………
10
90
80
Off
< While muting is engaged, the VOLUME level indicators blink.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Listening to CD/MP3 (1)
4
Press the OPEN/CLOSE button to close the CD door.
3
< It takes a few seconds for the unit to load the disc. No
buttons will work during loading. Wait until the total number
of the tracks and the total play time of the disc are displayed.
< When no disc is loaded in the CD player, “NO DISC” is
displayed.
2
5 4
1
When a CD is loaded
total tracks
total playing time
1
2
Press the FUNCTION button to select “CD”.
Press the OPEN/CLOSE button.
When a MP3 disc is loaded
total tracks
total number of folders
3
Put a disc onto the center spindle of the player with the
label side facing you.
Press the disc onto the spindle until a slight “click” is heard
indicating the disc is mounted correctly.
5
Press the Play/Pause button (y/J) to start playback.
Playback starts from the first track of the disc.
< MP3 tracks recorded out of folders are automatically put in
the “ROOT” folder, and playback starts from the first track of
the ROOT folder.
< When the playback of all the tracks has finished, the unit
stops automatically.
< Never put more than one disc in the mechanism at a time.
< Ensure that the disc is correctly mounted on the spindle and
locked in place.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Listening to CD/MP3 (2)
Search for a part of a track
During playback, hold down the skip button (.or/) and
release it when the part you want to listen to is found.
ESP (Electronic Shock Protection)
MP3
The ESP stores the music in the buffer to prevent sound from
skipping.
To suspend playback temporarily
(pause mode)
During playback of a CD, press the MP3 button to turn the
ESP on or off. When you turn the ESP on, “40 SEC (40
seconds)” briefly appears, and the (ESP) indicator lights on the
display.
Press the Play/Pause button (G/J) during playback. Playback
stops at the current position. To resume playback, press the
Play/Pause button (G/J) again.
< The (ESP) indicator blinks while the unit is filling the buffer.
< When the unit is on the stable place and free from
mechanical shocks, you can turn this function off.
< During playback of MP3, this function is always ON.
To stop playback
Press the Stop button (H) to stop playback.
To display the MP3 information
During playback of MP3 disc, press the MP3 button for more
than 1 second. The information about the current track is
displayed as follows:
To skip to the next or a previous track
FILE (folder name)wTITLE (*)wARTIST (*)wALBUM (*)
*: track information
Press the MP3 button for more than 1 second again to cancel
the MP3 information mode.
During playback, press the skip button (. or/ )
repeatedly until the desired track is found. The selected track
will be played from the beginning.
In the stop mode, press the skip button (. or/)
repeatedly until the track you want to listen to is found. Press
the Play/Pause button (G/J) to start playback from the
selected track.
Skip to the next folder (MP3)
Press the MP3 FOLDER button to skip to next folder.
< When the . button is pressed during playback, the track
being played will be played from the beginning. To return to
the beginning of the previous track, press the . button
twice.
< During programmed playback, the next or previous track in
the program is played.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Search Mode (MP3 only)
4
Press the PLAY/PAUSE button (G/J).
Playback starts from the selected track.
Search for a track in a folder
MP3
1
Press the MP3 button twice.
Search for a name of track
You can select the track by searching for its name.
The name of folder is displayed.
1
Press the MP3 button once.
2
Press the SKIP button (. or /) to find the folder
that the track you want to listen to is included.
An alphabet (initial letter of a track name) and a track name
are displayed.
Track name
Track number
Initial letter of track name
3
Press and hold the SKIP button (. or /).
< To cancel the search mode, press the STOP button (H).
Then you can select the track in the folder by pressing the
SKIP button (. or /).
2
Select the initial letter of the track you want to listen to
< MP3 tracks recorded out of folders are in the “ROOT” folder.
by pressing the SKIP button (. or /).
4
Press the PLAY/PAUSE button (G/J) to start playback.
Playback starts from the selected track.
3
Press and hold the SKIP button (. or /).
3
< If you skip step , playback will start from the first track in
the selected folder.
Then you can select the track that has same initial letter by
pressing the SKIP button (. or /).
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Programmed Playback
4
Press the Skip button (.or/) repeatedly to select a
track, then press the MEMORY button.
MEMORY
FUNCTION
Up to 64 tracks can be programmed in the desired order.
Shuffle function doesn’t work during programmed playback.
1
Press the FUNCTION button to select “CD”.
The track is programmed, and “P-02” is displayed.
2
Press the MEMORY button.
3
4
< Repeat steps and to program more tracks.
< You can program up to 64 tracks.
5
When the selection of track numbers is completed,
press the Play/Pause button (G/J) to start program
playback.
“MEMORY” lights up in the display.
< When the playback of all the programmed tracks has finished,
or if one of the following buttons is pressed, the MEMORY
indicator will go off and the program mode will be cancelled:
< To cancel the program mode, press the Stop button (H).
3
Press the Skip button (.or/) repeatedly to select a
folder of a MP3 disc, then press the MEMORY button.
STOP, FUNCTION, STANDBY/ON
< MP3 tracks recorded out of folders are in the “01” (ROOT)
folder.
< Skip this step when playing a CD.
The program is retained in memory until the OPEN/CLOSE
button is pressed or the power is interrupted. You can return
to the programmed playback by pressing the MEMORY
button and the Play/Pause button (G/J). (If another source
was selected, select the CD mode by pressing the FUNCTION
button beforehand.)
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Repeat Playback
MEMORY
Every time the REPEAT button is pressed, the mode is
changed as follows:
To check the programmed order
When a CD is loaded:
REPEAT 1
REPEAT ALL
(off)
In the stop mode, press the MEMORY button repeatedly. The
track number and program number will be shown on the
display.
When a MP3 disc is loaded.
REPEAT REPEAT ALL
(off)
REPEAT ALBUM
To add a track to the end of the program
In the stop mode, press the MEMORY button repeatedly until
“00” appears on the display. Select a track number using the
Skip button (.or/) and then press the MEMORY
button. The track is added to the end of the program.
< If one of the following buttons is pressed, repeat mode will
be canceled:
STOP, FUNCTION, OPEN/CLOSE, STANDBY/ON
To overwrite the program
Repeat one track
In the stop mode, press the MEMORY button repeatedly until
the program number to be changed appears on the display.
Select a new track number using the Skip button (.or/)
and then press the MEMORY button.
Press the REPEAT button once during playback. “REPEAT”
lights.
The track being played will be played repeatedly. If you press
the Skip button (.or/) and select another track, the
track you selected will be played repeatedly.
It is also possible to select a track to be repeated in the stop
mode. Press the REPEAT button, select a track using the Skip
button (.or/), and then press the Play/Pause button
(G/J) to start playback.
To clear program
Repeat all the tracks
All the tracks will be played repeatedly.
Press the REPEAT button twice. “REPEAT ALL” lights.
During programmed playback, programmed tracks will be
played repeatedly.
To clear the programmed contents, press the MEMORY and
the STOP button (H) in the stop mode.
Repeat all the tracks in the folder (MP3)
< If the OPEN/CLOSE button is pressed, the programmed
contents will also be cleared.
All the tracks in the folder will be played repeatedly.
Press the REPEAT button three times. “REPEAT ALBUM”
lights.
< If the unit is disconnected from the power supply, the
programmed contents will be cleared.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Shuffle Playback
Listening to an External Source
1
3
2
1
The tracks can be played randomly. Press the SHUFFLE button
during playback or when in the stop mode. “SHUFFLE” will
then light up in the display.
Connect the PHONES jack (audio output jack) of a
portable audio player to the AUX IN jack of the CD-X9
using the supplied stereo mini plug cable.
< If you press the / button during shuffle playback, next
track will be randomly selected and played. If you press the
. button, the currently played track will be played from
the beginning. A track cannot be replayed during shuffle
playback.
< Shuffle playback doesn’t work during programmed playback.
< If one of the following buttons is pressed, shuffle mode will
be cancelled:
SHUFFLE, STOP, FUNCTION, STANDBY/ON, OPEN/CLOSE
2
3
Press the FUNCTION button to select “AUX”.
Play the source, and adjust the volume using the
VOLUME buttons of the CD-X9 and the audio player.
When using the PHONES jack of your mini player, you must
adjust the volume of the mini-player or you may hear no
sound from your CD-X9.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Listening to the Radio
FM MODE button
Pressing this button alternates between STEREO mode and
MONO mode.
1 2
3
1
2
Press the FUNCTION button to select “TUNER”.
STEREO
FM stereo broadcasts are received in stereo and the
“STEREO” indicator lights in the display.
Press the FM/AM button to select a band.
< If the sound is distorted and the “STEREO” indicator flashes,
the signal is not strong enough for good stereo reception. In
this case, change to MONO mode.
MONO
To compensate for weak FM stereo reception, select this
mode. Reception will now be forced to monaural, reducing
unwanted noise.
3
Select the station you want to listen to (auto selection).
If the reception is poor
AM broadcast
Hold down the TUNING Up or Down button until the
frequency display begins to change. When a station is tuned
in, the tuning process will stop automatically.
Rotate or relocate the AM antenna to find the best position
for AM stations.
FM broadcast
< Press the Up or Down button to stop the auto selection.
Extend and rotate the FM antenna until you receive the
stations clearly. You may need to relocate the unit.
Selecting stations which cannot be tuned automatically
(manual selection)
When the Up or Down button is pressed momentarily, the
frequency changes by a fixed step.
Press the Up or Down button repeatedly until the station you
want to listen to is found.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Preset Tuning
4
You can store FM and AM stations into preset channels 1 to 10
respectively.
Within 5 seconds, press the MEMORY button.
If the power switch of the subwoofer turned off, the
settings kept in memory (clock, preset stations, timer
setting) will be erased.
1
2
1
Tune in a station you want to listen to (see steps
to
3
of page 17).
The station is stored and the MEMORY indicator goes off.
Press the MEMORY button.
1
4
To store more stations, repeat steps to
.
How to select preset stations
1
Press the FM/AM button to select a band.
3
Within 5 seconds, select a preset channel to store the
station using the PRESET buttons of the remote control
unit.
2
Press the PRESET button repeatedly until the desired
preset station is found.
preset channel
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the Clock
4
Press the SKIP button (.//) to set the current
hour.
MEMORY/
TIME SET
STANDBY/ON
5
6
7
If the power switch of the subwoofer turned off, the
settings kept in memory (clock, preset stations, timer
setting) will be erased.
Press the TIME SET button.
The “minute” value blinks.
1
If the unit is on, press the STANDBY/ON switch to turn
it standby
2
Press and hold down the TIME SET button.
Press the SKIP button (.//) to set the current
minute.
“12 HOUR” or “24 HOUR” blinks. If you want to change the
hour mode, press the .or/ button.
< If no button is pressed for 10 seconds, the time setting mode
will be cancelled.
3
Press the TIME SET button once more.
Press the TIME SET button.
The “hour” value blinks.
The clock starts.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the Timer
3
Press the SKIP button (.//) to set the start time
(minute), and then press the TIMER button.
< The unit can be programmed to turn on and off at a specified
time.
< Adjust the clock before setting the timer.
“TIMER” and “OFF” indiactors appear on the display and the
“hour” value starts flashing.
1
Press and hold the TIMER button until “TIMER” and
“ON” indicators appear on the display.
4
Press the SKIP button (.//) to set the stop time
(hour), and then press the TIMER button.
The “hour” value starts flashing.
< When no button is pressed for 10 seconds, the timer setting
mode will be cancelled.
2
Press the SKIP button (.//) to set the start time
(hour), and then press the TIMER button.
The “minutes” value starts flashing.
5
Press the SKIP button (.//) to set the stop time
(minute), and then press the TIMER button.
The “minutes” value starts flashing.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Press the SKIP button (.//) to select a source (CD
or TUNER), and then press the TIMER button.
To turn on or off the timer
When you don’t use the timer, press the TIMER button to
turn it off. (The TIMER indicator disappears from the display.)
Press the TIMER button again to turn it on.
< When the timer is turned on, the timer settings are displayed
one by one, and the TIMER indicator lights on the display.
7
Press the SKIP button (.//) to set the volume, and
then press the TIMER button.
Setting the timer is now completed and the timer is turned on.
Your timer setting is displayed one by one, and the TIMER
indicator lights on the display.
8
9
Prepare the source.
When the source is set to “CD”, set a CD.
When the source is set to “TUNER”, tune in a station.
Press the STANDBY/ON button to turn the unit off
(standby).
The clock and the TIMER indicator are displayed.
The unit will turn on and off at the specified time every day.
Don’t forget to turn the unit off (standby), or the timer
won’t work.
If the power switch of the subwoofer turned off, the
settings kept in memory (clock, preset stations, timer
setting) will be erased.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
If you have problems with your system, look through this chart
and see if you can solve the problem yourself before calling your
dealer or TEAC service center.
Tuner
Cannot listen to any station, or signal is too weak.
e Tune in the station properly.
e Rotate the FM or AM antenna for the best reception
position.
General
No power
Though the broadcast is stereo, it sounds monaural.
e Check the connection to the AC power supply. Check and
make sure the AC source is not a switched outlet and that,
if it is, the switch is turned on. Make sure there is power to
the AC outlet by plugging another item such as a lamp or
fan into the outlet.
e Press the FM MODE button.
If normal operation cannot be recovered, unplug the
power cord from the outlet and plug it again.
No sound from speakers.
e Select the source by pressing the FUNCTION button.
e Check the connection to the speakers.
e Adjust the volume.
If the power switch of the subwoofer turned off, the
settings kept in memory (clock, preset stations, timer
setting) will be erased.
e Pull out the headphone’s plug from the PHONES jack.
eIf the VOLUME level indicator is blinking, press the MUTING
button. (When “CD” is selected, press the Play/Pause button
(G/J) to start playback.)
Beware of condensation
When the unit (or a disc) is moved from a cold to a warm
place, or used after a sudden temperature change, there is a
danger of condensation; vapor in the air could condense on
the internal mechanism, making correct operation erratic or
impossible. To prevent this, or if this occurs, leave the unit for
one or two hours with the power turned on. The unit will
stabilize at the temperature of its surroundings.
The sound is noisy.
e The unit is too close to a TV or similar appliances. Install the
unit apart from them, or turn them off.
Remote control doesn’t work.
e Press the STANDBY/ON switch to turn the unit on.
e When the battery has run out, put in a new one.
e Use remote control unit within the range (5 m) and point at
the front panel.
Maintenance
e Clear obstacles between the remote control unit and the
main unit.
e If a strong light is near the unit, turn it off.
If the surface of the unit gets dirty, wipe with a soft cloth or
use diluted mild liquid soap. Never spray liquid directly on this
unit. Apply your cleaner to your cleaning cloth and wipe
gently. Be sure to remove any excess completely. Do not use
thinner, benzene or alcohol as they may damage the surface
of the unit. Allow the surface of the unit to dry completely
before using.
CD Player
Will not play.
e Load a disc with the playback side facing away.
e If the disc is dirty, clean the surface of the disc.
e A blank disc has been loaded. Load a prerecorded disc.
e Depending on the disc, etc. it may not be possible to play
back CD-R/RW discs. Try again with another disc.
e You cannot play back unfinalized CD-R/RW discs. Finalize
such a disc in a CD recorder and try again.
Sound skips.
e Place the unit on a stable place to avoid vibration and shock.
e If the disc is dirty, clean the surface of the disc.
e Don’t use scratched, damaged or warped discs.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Standard Accessories
AMPLIFIER section
Remote Control Unit (RC-1045) x 1
Subwoofer Cable x 1
Speaker Cable x 2
Output Power (L+R) . . . . . . . . . . . . . . . . . . . . . . . 5 W + 5 W
Output Power (Subwoofer) . . . . . . . . . . . . . . . . . . . . . . 15 W
Input Sensitivity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 300 mV
Frequency Response. . . . . . . . . . . . . . . . . . . 50 to 20,000 Hz
FM Antenna x 1
AM Antenna x 1
Battery for Remote Control Unit x 1
Wall Mount Adaptor x 3
Wall Mount Screw x 10
Tapered Plastic Wall Anchor x 10
Template for Wall Mounting x 1
Stereo mini plug cable x 1
Owner’s Manual x 1
TUNER Section (FM)
Frequency Range . . . . . . . . . . . . . . . . . 87.50 to 108.00 MHz
Sensitivity (S/N30dB). . . . . . . . . . . . . . . . . . . . . . . 20 dBµV/m
TUNER Section (AM)
Warranty Card x 1
Frequency Range . . . . . . . . . . . . . . . . . . . . 520 to 1,710 kHz
Sensitivity (S/N20dB). . . . . . . . . . . . . . . . . . . . . . . 54 dBµV/m
< Design and specifications are subject to change without
notice.
< Weight and dimensions are approximate.
< Illustrations may differ slightly from production models.
CD PLAYER Section
Frequency Response . . . . . . . . . . . . . 20 to 20,000 Hz ( 1 dB)
Signal-to-Noise Ratio . . . . . . . . . . . . . . . . . . . . . . . . . . 55 dB
Wow and Flutter . . . . . . . . . . . . . . . . . . . . . . . Unmeasurable
SPEAKER
Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Full range flat type
Impedance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 ohms
SUBWOOFER
Impedance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 ohms
GENERAL
Power Requirements . . . . . . . . . . . . . . . . . . 120 V AC, 60 Hz
Power Consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . 80 W
Dimension ( W x H x D )
Main Unit . . . . . . . . . . . . . . . . . . 6 5/16” x 8 7/8” x 3 3/8”
(160 x 226 x 86 mm)
L & R Speakers . . . . . . . . . . . . . . 5 9/16” x 8 7/8” x 2 3/4”
(142 x 226 x 70 mm)
Subwoofer . . . . . . . . . . . . . . . 6 5/16” x 9 5/8” x 13 3/16”
(160 x 245 x 335 mm)
Weight
Main Unit . . . . . . . . . . . . . . . . . . . . . . . . 2 3/16 lbs (1 kg)
L & R Speakers. . . . . . . . . . . . . . . . 1 5/16 lbs (0.6 kg) each
Subwoofer . . . . . . . . . . . . . . . . . . . . 11 11/16 lbs (5.3 kg)
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Z
3-7-3, Nakacho, Musashino-shi, Tokyo 180-8550, Japan Phone: (0422) 52-5081
TEAC CORPORATION
TEAC AMERICA, INC.
TEAC CANADA LTD.
TEAC MEXICO, S.A. De C.V
TEAC UK LIMITED
7733 Telegraph Road, Montebello, California 90640 Phone: (323) 726-0303
5939 Wallace Street, Mississauga, Ontario L4Z 1Z8, Canada Phone: (905) 890-8008
Campesinos N°184, Colonia Granjas Esmeralda, Delegacion Iztapalapa, CP 09810, México DF Phone: (525) 581-5500
Unit 19 & 20, The Courtyards, Hatters Lane, Watford, Hertfordshire, WD18 8TE , U.K. Phone: (0845) 130-2511
Bahnstrasse 12, 65205 Wiesbaden-Erbenheim, Germany Phone: 0611-71580
TEAC EUROPE GmbH
TEAC ITALIANA S.p.A.
Via C. Cantù 11, 20092 Cinisello Balsamo, Milano, Italy Phone: 02-66010500
TEAC AUSTRALIA PTY., LTD.
A.B.N. 80 005 408 462
280 William Street, Melbourne VIC 3000, Australia Phone: (03) 9672-2400
This appliance has a serial number located on the rear panel. Please record
the model number and serial number and retain them for your records.
.
Model number
Serial number
0605 MA-0984A
Download from Www.Somanuals.com. All Manuals Search And Download.
|