INSTA LLATION INSTRUCTIONS FOR PA RT 9 9 -8 2 12
APPLICATIONS
2004-2008 Toyota Solara
9 9 -8 2 12
KIT FEATURES
• DIN Head Unit Provisions with Pocket
• ISO DIN Head Unit Provisions with Pocket
KIT COMPONENTS
A) Radio Housing w/ Pocket • B) ISO Brackets
C) Radio Housing Brackets • D) (2) PTH-838 Phillips Screws • E) (8) PFH-614 Phillips Screws
F) Trim Plate • G) X-9002 Radio Support Bracket
D
E
C
A
B
F
G
TOOLS REQUIRED:
Socket Wrench • Small Flat Blade Screwdriver • Phillips Screwdriver
1-800-221-0932
© COPYRIGHT 2004-2007 METRA ELECTRONICS CORPORATION Rev.10-02-07
Download from Www.Somanuals.com. All Manuals Search And Download.
9 9 -8 2 12
2 0 0 4 -2 0 0 8 TOYOTA SOLA RA
A
Disconnect the negative battery
terminal to prevent an accidental
short circuit.
1
2
Remove the cover from the hazard
switch then unclip and remove the
switch. (Figure A)
B
Unclip and remove panel above radio
including A/C vents and clock.
3
TIP: Start pulling from the inside of
the hazard switch cavity. (Figure B)
Unclip and remove panel surrounding
shifter. (Figure C)
4
5
C
Unclip and remove pocket and seat
heater switch panel. (Figure D)
Remove (4) 10mm screws to extract
6
radio from sub dash. (Figure E)
E
D
1
Download from Www.Somanuals.com. All Manuals Search And Download.
9 9 -8 2 12
2 0 0 4 -2 0 0 8 TOYOTA SOLA RA
Attach the corresponding radio
housing bracket to the radio housing
using the included (8) PFH-614 Phillips
screws.
1
Slide the factory climate control into the
assembled radio housing brackets/radio
housing assembly and secure with the
factory hardware.
2
Attach the radio support to the back of
the pocket using the supplied (2) PTF-
838 Phillips screws.
3
2
Download from Www.Somanuals.com. All Manuals Search And Download.
9 9 -8 2 12
DIN HEA D UNIT P ROVISIONS
A
Slide the DIN cage into the radio
housing and secure by bending the
metal locking tabs down. (Figure A)
1
2
Slide the aftermarket head unit into
the cage and secure. (Figure B)
B
3
Download from Www.Somanuals.com. All Manuals Search And Download.
9 9 -8 2 12
ISO DIN HEA D UNIT P ROVISIONS
A
Mount the ISO Brackets to the head
unit with the screws supplied with
the unit. (Figure A)
1
Slide the head unit into the radio
opening until the side clips engage.
(Figure B)
2
B
Snap the trim plate into the radio
3
housing. (Figure B)
4
Download from Www.Somanuals.com. All Manuals Search And Download.
9 9 -8 2 12
A
B
A)
B)
C)
D)
Strip wire ends back 1/2"
Twist ends together
Solder
Tape
C
D
Locate the factory wiring harness in the
dash. Metra recommends using the proper
mating adapter and making the connections
as shown. (Isolate and individually tape off
the ends of any unused wires to prevent
electrical short circuit)
1
Re-connect the negative battery terminal
and test the unit for proper operation.
2
Reassemble radio and dash assemblies in
reverse order of disassembly.
3
5
Download from Www.Somanuals.com. All Manuals Search And Download.
INST9 9 -8 2 12
1-800-221-0932
Rev. 07-02-07
© COPYRIGHT 2004-2007 METRA ELECTRONICS CORPORATION
INST99-8212
Download from Www.Somanuals.com. All Manuals Search And Download.
|