TEW-610APB
Quick Installation Guide
Version 8.19.2005
TRENDnet
What's Next in Networking
TRENDware, USA
Download from Www.Somanuals.com. All Manuals Search And Download.
Copyright ©2005. All Rights Reserved. TRENDware International, Inc.
English QIG
1. Prepare for Installation
Thank you for purchasing TRENDnet's TEW-610APB 108Mbps 802.11g MIMO
Wireless Access Point.
This guide will help you set-up your Access Point quickly and easily. Just follow
the step-by-step instructions below, and enjoy the benefits of accessing the
Internet/network without ever being tied down to wires! If you run into
problems, please refer to the Troubleshooting section. If you need further
by phone.
Verify Package Contents
Please make sure you have everything in the box:
TEW-610APB
CD-ROM (User’s Guide)
TEW-610APB
Quick Installation Guide
Version 8.19.2005
TRENDnet
What's Next in Networking
TRENDware, USA
Copyright ©2005. All Rights Reserved. TRENDware International, Inc.
External Power Adapter
1.5M RJ45 cable
Quick Installation Guide
Verify Equipment
Before setting up the Access Point, you should have:
1. A Computer with a Wired (RJ45) or Wireless network card.
2. TCP/IP protocol installed on the Computer.
3. A Web Browser such as Internet Explorer (5.0 or higher) or
Netscape Navigator (4.7 or higher).
4. A Hub or Switch connecting your existing wired network.
5. An RJ-45 Network Cable for connecting the Access Point to your
network Switch.
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Install Hardware
1. Locate an optimum location for the Access Point. The best place for the
Access Point is usually at the center of your wireless network.
2. Connect the RJ-45 network cable to the Access Point, then connect the
other end of the network cable to a Switch or Hub. The Access Point is now
connected to your 10/100Mbps network.
3. Connect the power adapter to the Access Point. Make sure you use the
power adapter supplied with the Access Point; using a different power
adapter may damage the unit.
TEW-610APB
NOTE: If you are using a wired computer to configure the Access Point,
please connect this computer to the same Switch or Hub the
TEW-610APB is connected to.
Verify Hardware Installation
Make sure the front panel lights are on: Power, LAN, MIMO.
LAN
MIMO
POWER
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Configure TCP/IP Settings
Before the Access Point can be accessed and configured, the computer's
TCP/IP settings need to be changed. (That includes your wireless card's IP
address, too.)
Windows 2000/XP
1. Find the Start button located on the Desktop.
2. Click Start, and click on Control Panel. For Windows 2000, click Start,
highlight Settings, and click Control Panel.
3. Double-Click the Network Connection icon.
4. Right-Click on the Local Area Connection icon, then click on Properties.
The Local Area Connection Properties box will appear.
5. Under the General tab, locate and select Internet Protocol TCP/IP and
then click Properties. The Internet Protocol (TCP/IP) Properties box will
appear.
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Click on Use the following IP address. Enter 192.168.0.50 for IP address
and 255.255.255.0 for Subnet, and click OK.
7. Click OK.
8. Your computer is now ready to access and configure the Access Point.
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Configure the Access Point
From a Wired Computer
1. Open a web browser (Internet Explorer or Netscape) and enter
admin for username, and type admin for your password. Click OK.
2. Click admin and scroll down to the IP Settings section. Change the default
IP address, subnet mask, and default gateway to match your current
network settings. Your default gateway's IP address should be your router's
IP Address. Type your router's IP address for your default gateway address.
Click Save.
3. Click Reboot.
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Configure your Wireless Network
Adapter
In this example, the TEW-601PC Wireless Utility will connect to the
TEW-610APB.
1. Double-click the wireless computer icon in your system tray (next to the
clock in the bottom right corner of your screen).
2. Click Site Survey, click Refresh, and select the desired access point. Click
Connect.
3. Click OK.
4. Please verify your connection status.
Congratulations! Installation is now complete.
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
address bar, but error message says "The page cannot be displayed". How can I
get into the TEW-610APB's web configuration page?
A1: Please check your hardware and TCP/IP settings again by following the
instructions sections 1~3, make sure the Power, LAN, MIMO on the Access
Point's front panel are on and the TCP/IP configurations are correct. then try
Q2: If my network's IP is different than the Access Point's range, what should I
do?
A2: You should still configure the access point first. After all the settings are applied,
go to the Access Point's configuration page, click on TCP/IP settings and change an
IP address for the Access Point to match your network's IP.
Q3. After I successfully configured the Access Point to meet my network settings,
I cannot connecting to my network using wireless computers.
A3: If you have a DHCP server in your network, you need to go into TCP/IP
settings again and re-select "Obtain an IP automatically" for Windows 98/ME and
"Obtain an IP Address automatically" for Windows 2000/XP to allow the PC to
regain an IP address from your DHCP server.
Q4. All the settings are set correctly, but I still can't use the Access Point, what
should I do?
A4: You can find additional information in the User's Guide. If you still have
Problems, contact our Technical Support by email or phone.
Certifications
This equipment has been tested and found to comply with FCC and CE Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received.
Including interference that may cause undesired operation.
NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV
INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS
EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO
OPERATE THE EQUIPMENT.
Download from Www.Somanuals.com. All Manuals Search And Download.
TRENDnet
TRENDware, USA
What's Next in Networking
Product Warranty Registration
Please take a moment to register your product online.
Go to TRENDware’s website at http://www.TRENDNET.com
TRENDnet Technical Support
US/Canada Support Center European Support Center
Contact
Contact
Telephone: 1(310) 626-6252
Fax: 1(310) 626-6267
Email: [email protected]
Telephone
Deutsch : +49 (0) 6331 / 268-460
Français : +49 (0) 6331 / 268-461
08-00-90-71-61 (numéro vert)
Tech Support Hours
7:30am - 6:00pm Pacific Standard Time
Monday - Friday
Español : +49 (0) 6331 / 268-462
English : +49 (0) 6331 / 268-463
Italiano : +49 (0) 6331 / 268-464
Dutch : +49 (0) 6331 / 268-465
Fax: +49 (0) 6331 / 268-466
Tech Support Hours
8:00am - 6:00pm Middle European Time
Monday - Friday
TRENDware International, Inc.
3135 Kashiwa Street. Torrance, CA 90505
http://www.TRENDNET.com
Download from Www.Somanuals.com. All Manuals Search And Download.
Copyright ©2005. All Rights Reserved. TRENDware International, Inc.
|