Download from Www.Somanuals.com. All Manuals Search And Download.
1.2 Port TRUNK......................................................................................................... 2
3.2 Rear Panel........................................................................................................... 6
4.8 Config effect....................................................................................................... 22
Appendix A: TL-SF2109P Technical Specification........................................................... 25
Appendix B: TL-SF2117P Technical Specification........................................................... 26
Appendix C: TL-SL2226P Technical Specification........................................................... 27
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-SF2109P/TL-SF2117P/TL-SL2226P Ethernet Smart Switch User Guide
Package Contents
The following contents should be found in your box:
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
One TL-SF2109P/TL-SF2117P/TL-SL2226P Smart Switch
One power cord
One serial cord
This User’s Guide
One Resource CD
Rubber footpads for Desk-mount
Rack-mount kit for installing the switch in a 19-inch rack
Note: If any of the above contents is damaged or missing, please contact the retailer
from whom you purchased the TL-SF2109P/TL-SF2117P/TL-SL2226P Ethernet Smart
Switch for assistance.
- 1 -
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-SF2109P/TL-SF2117P/TL-SL2226P Ethernet Smart Switch User Guide
Chapter 1: Introduction of the Product
This chapter simply describes the features of the model of the TL-SF2109/TL-SF2117P
/TL-SL2226P smart Switch and back-knowledge of Fast Ethernet Switch.
1.1 Virtual Local Area Network (VLAN)
Virtual Local Area Network breaks down the constraint of environment, you can move the
workstation freely in the group without change the connection. The technology improves
the performance or subnet of the system, equalizes data flow in the net, utilizes the
resource reasonably, the work of management and maintenance.
Virtual group: The communication will be improved among the group. And there needs
no routers in the group when transferring data to other groups.
Safety: Only the legal users can forward data in the VLAN. So the safety of the net
improves.
Low cost: You can move the workstations freely in the VLAN, and there need no routers
and replacing the cable.
1.2 Port TRUNK
Generally, TRUNK means that two switches can be connected two or more than two (but
less than five) ports side-by-side to supply more band width and more throughput and
self-resume technic. This is to say, TRUNK is to treat several physical connections as
one logic connection. TRUNK is very useful to several lower speed device to a high
speed device.
The current device can simply add more NIC connecting to the server to resolve the
traffic between the switches and the servers.
1.3 AUTO MDI/MDIX
The switch supports MDI/MDIX function, every port of the Switch can be used as normal
port and uplink port. It becomes easy to use, plug and play, when connecting to the other
switches and hubs, whether the direct cable and the crossover cable or not.
The switch, a smart auto-negotiated Ethernet switch, supplies the method of promotion
of the workstation resource.
1.4 Features
ꢀ
Complies with IEEE802.3, IEEE802.3u, IEEE802.3ab and IEEE802.3z (only for
TL-SL2226P) standards
ꢀ
8/16/24 10/100Mbps Auto-Negotiation RJ45 ports supporting Auto MDI/MDIX
- 2 -
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-SF2109P/TL-SF2117P/TL-SL2226P Ethernet Smart Switch User Guide
ꢀ
1/1/2 extension slots supporting 100M fiber module card (TL-SM201 series) and
TL-SL2226P supports 1000M fiber/UTP module (TL-SM301 series)
ꢀ
Supports IEEE802.3x flow control for Full Duplex mode and backpressure for
half-duplex mode
ꢀ
ꢀ
Supports Port Enable/Disable
Supports 9 Port VLAN and 9 IEEE802.1Q Tag VLAN (for TL-SF2109P), 17 Port
VLAN ( for TL-SF2117P) and 26 Port VLAN ( for TL-SL2226P)
ꢀ
ꢀ
Supports Port Mirror (only for TL-SF2117P)
Supports Port Trunk, up to 1 Trunk group (for TL-SF2109P) and 8 Trunk group (for
TL-SL2226P)
ꢀ
Supports Static Priority, TOS and 802.1p Class of Service with 2-level priority
queues (for TL-SF2109P and TL-SF2117P)
ꢀ
ꢀ
ꢀ
Easy read LED indicators for installation and operation
Support a RS232 interface for smart configuration (example :VLAN, Trunk, Priority )
Desktop Steel case (for TL-SF2109P) and standard 19-inch rack-mountable steel
case (for TL-SF2117P and TL-SL2226P), internal power supply
- 3 -
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-SF2109P/TL-SF2117P/TL-SL2226P Ethernet Smart Switch User Guide
Chapter 2: Installation
2.1 Mounting the Switch on a Desk
Before place the Switch on a desk, attach four rubber footpads to the flutes on the Switch
bottom, then lay the Switch on the desktop, where can be have as much as 5kg placed
on top.
Note: Make sure there is a grounded AC outlet within 1.5 meters, and working well.
Make sure there is free space for radiating heat and air.
Make sure not to place anything to heavy on top of the switch.
2.2 Mounting the Switch in a Rack
The dimension of the Switch is designed according to the standard 19” rack-mountable
steel case of Electronic Industries Association.
Turn off all the equipment connected to the Switch before mounting it in the rack, then
rivet the two “L” brackets onto each side of the Switch, fasten it with screwes in the rack.
Figure 2-1 Rivet the “L” brackets onto the Switch
- 4 -
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-SF2109P/TL-SF2117P/TL-SL2226P Ethernet Smart Switch User Guide
Figure 2-2 Fasten the Switch in the rack
2.3 Power on
The Switch is powered by AC power supply. Powering on the Switch, it will automatically
initialize and its LED indicators should respond as follows:
1) All of the LED indicators will flash momentarily for one second, which represent a
resetting of the system.
2) The power LED indicator will remain ON.
- 5 -
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-SF2109P/TL-SF2117P/TL-SL2226P Ethernet Smart Switch User Guide
Chapter 3: Identifying External Components
This Chapter describes the front panel, rear panel and LED indicators of the Switch.
Cautions:
All the pictures are based on the TL-SF2109P in the manual. The others are similar with
the TL-SF2109P.
3.1 Front Panel
The front panel of the TL- SF2109P consists of switch LED indicators, 8 10/100Mbps
RJ-45 ports, and 1 serial port Connect the female of the power cord head here.
Console
10/100Mbps Fast Ethernet Smart Switch
Figure 3-1 TL- SF2109P Switch Front Panel sketch
ꢀ
Serial port: Config the system by the serial cable (more details in chapter 4)
3.2 Rear Panel
The rear panel of the TL-SF2109P only features a power receptacle, which is an AC
power receptacle , and 1 extension slots. Connect the female of the power cord head
here, and the male head to the AC power outlet.
ꢀ
Extension slot: This is a optional module slot which can connect to a 100M
UTP/fiber (Tl-Sf2109P and TL-SF2117P) or a 1000M fiber module or 10/100/1000M
UTP module card(TL-Sl2226P).
Slot
Figure 3-2 TL- SF2109P Switch Rear Panel sketch
ꢀ
Power connector: This is a 3-Phase power socket, Plug the connector with a
100~240VAC/50-60Hz power supply.
- 6 -
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-SF2109P/TL-SF2117P/TL-SL2226P Ethernet Smart Switch User Guide
3.3 LED indicators
The LED indicators include Power, 100Mbps, Link/ACT and slot can display the working
status of the switch, more details as follows:
10/100Mbps Fast Ethernet Smart Switch
Figure 3-3 TL- SF2109P Switch LEDs sketch
ꢀ
ꢀ
ꢀ
ꢀ
Power LED: After power on, the LED will be light always. If it is turned off, check the
connection of the power source.
100Mbps LED: When a port is connected to a device with the 100Mbps, the
corresponding green LED is light, or else it is turned off.
Link/ACT: when transferring the data between two devices, the corresponding
LEDs will be flicker with green.
Slot: When inserted a UTP/fiber module card, LED is green. If it is turned off, check
the connection of the card. (The LED is only in TL-SF2109P)
3.4 Optional Slot Module
TL-SL2226P supports the TL-SM201/TL-SM301 serials module cards. TL-SF2109P and
TL-SF2117P supply the TL-SM201 serial module cards. Every type of modules contains
two category, fiber and UTP.
1） Fiber Modules
The switch supports many optional fiber module card, include the SMF and MMF their
interface is SC. Every module’s transporting distance is not the same, more details in
fiber module User’s Guide.
2） UTP Modules
TL-SF2109P and TL-Sf2117P’s module work only in 100M full-duplex, TL-SL2226P can
support 100/1000M module.
Caution:Before inserting the module, please turn off the power, take off the baffle, and
then insert the module along the rails, fasten the serwes finally.
- 7 -
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-SF2109P/TL-SF2117P/TL-SL2226P Ethernet Smart Switch User Guide
Chapter 4: Installation and Usage of the Configuration
Software
The switch is a smart switch, which can be configed the parameters by the supplied
software. So it is not a dump switch. The chapter tells you how to use the management
software.
4.1 Installation of the SSC
All the views in the manual are base on TL-SF2109P, the other switches’ interface will be
not the same, only the function is supported, the corresponding icons will be light.
The configuration program runs in the window OS (95/98/2000/NT). The software
configs the switch by the serial port of the PC. So before your installation the software,
you should have check that the computer has the serial port and the valid windows OS.
1.
2.
3.
4.
Connect the serial cable from the computer to the switch.
Turn on the serial port and the valid windows OS.
Run the setup.exe in the CD, and click “Next” to continue it.
The default installation path is “X: Program Files\TP-LINK\Smart Switch
Configuration”. (X: is the system disk). If you want to change the directory, click the
Browse button.
- 8 -
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-SF2109P/TL-SF2117P/TL-SL2226P Ethernet Smart Switch User Guide
5.
Input your new path, such as “D:\ Switch\TP-LINK\SSC”, and then press Enter.
6.
Click the “Next” button.
- 9 -
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-SF2109P/TL-SF2117P/TL-SL2226P Ethernet Smart Switch User Guide
7.
Click the “Next” button.
8.
Click the “Finish” to finish the installation.
- 10 -
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-SF2109P/TL-SF2117P/TL-SL2226P Ethernet Smart Switch User Guide
4.2 Usage of the SSC
The interface of the configuration software is friendly and easy to use, there are four
steps as follows:
1.
2.
3.
4.
Connection
Open the configuration file or config directly
Write out the current configuration
Escape
More details is following:
1.
After installation, click Start – Program – TP-LINK – Smart Switch Configuration
– Smart Switch Configuration, the desktop display the initialized interface.
2.
Assure the power is on. Click the “connect” or the icon of “Link to Switch”.
- 11 -
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-SF2109P/TL-SF2117P/TL-SL2226P Ethernet Smart Switch User Guide
3.
If the connection is failure, check the power or the serial cable. The program
display the follow message.
- 12 -
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-SF2109P/TL-SF2117P/TL-SL2226P Ethernet Smart Switch User Guide
4.
After connection, the software will read the current configuration of the switch, and
display the switch name (TL-SF2109P) automatically, and the connect status is
“connected”
Cautions:At the time, the “off line” icon will be light, or else it is gray. There are six icons
on the right of it. Port setting, TRUNK, VLAN, Priority, Static MAC Address and MAC
Address Age inturns.
5.
Config the switch
After having connected to the switch, you can config the switch parameters based on
your demand, and then write to the switch. Once successful configuration, the switch will
reset automatically and work at the mode you wanted.
4.3 Port Status Setting
1.
Click “Setting – Port Status Setting” or the corresponding icon, “Port Setting”.
- 13 -
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-SF2109P/TL-SF2117P/TL-SL2226P Ethernet Smart Switch User Guide
2.
Every port has its own parameters to be configed. You can only select the lighten
choice, not the grey choice.
- 14 -
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-SF2109P/TL-SF2117P/TL-SL2226P Ethernet Smart Switch User Guide
Here is a brief description about the parameters:
ꢀ
Speed/Duplex: ecided the port’s speed (10Mbps or 100Mbps) and the duplex (the
half duplex or a full duplex) mode. In half duplex mode, only translating or receiving
data at the same time. In full duplex mode, translating and receiving data can be
working at the same time.
ꢀ
ꢀ
Default Setting: 100 Base-Tx Full duplex (for TL-SF2109P), Auto negotiation (for
TL-SF2117P and TL-SL2226P)
Broadcast Storm Filtering: Click it to start the broadcast storm filtering, when the
function is enabled, the port will drop the broadcast frames after received 64
continuous broadcast frames.
ꢀ
ꢀ
Default Setting: Disable
Flow Control: This enable to turn flow control on or off when it is on, at full duplex
mode, the switch uses Port-based IEEE802.3x flow control, at half duplex mode, the
- 15 -
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-SF2109P/TL-SF2117P/TL-SL2226P Ethernet Smart Switch User Guide
switch use collision-based back pressure flow control. You can turn off the function,
thus there is no flow control.
ꢀ
Default Setting: Enable
ꢀ
Priority: Priority is a high feature of the switch, the switch with the function can
support that the important application can transfer firstly. Port-based priority means
every port can set its own priority.
ꢀ
Default Setting: Port-based priority.
4.4 TRUNK
TRUNK can transmit net data through a group of ports. The switch looks a TRUNK as a
big port regardless of it’s composition.
TL-SF2109 support two TRUNK, port1, port2 and port 7, port 8, but only one trunk at the
same time.
TL-SF2117P does not support TRUNK.
TL-SL2226P supports 8 TRUNK, 1,2; 3,4;5,6,7,8; 9,10,11,12; 13,14,15,16; 17,18,19,20;
21, 22, 23, 24; 25,26 (Slot 1, Slot 2).
Default Setting: None.
1.
Click “TRUNK” or the “TRUNK Setting” icon.
2.
And then select the certain trunk with “√ ”.
- 16 -
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-SF2109P/TL-SF2117P/TL-SL2226P Ethernet Smart Switch User Guide
Cautions:When setting TRUNK, the system will set the ports in a TRUNK to 100M full
duplex.
4.5 VLAN
VLAN is composed of a group of workstations’ multicast domain, which can build up the
logic group without change the current topology.
- 17 -
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-SF2109P/TL-SF2117P/TL-SL2226P Ethernet Smart Switch User Guide
TL-SF2109 supports two methods of VLAN: Port-based VLAN and Tag-based VLAN.
TL-SF2117P and TL-SL2226P support only port-based VLAN.
Default Setting: All ports in VLAN 1.
Port-based VLAN Setting:
1.
Click the “VLAN” in menu, or the “VLAN setting” icon;
2. Select VLAN mode to Port VLAN;
3.
And then move the cursor into the VLAN group you want to change, Click the ports,
such as P2, P3, P4 and P5.
- 18 -
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-SF2109P/TL-SF2117P/TL-SL2226P Ethernet Smart Switch User Guide
Cautions:Ports in VLAN can exist in other VLANs, and VLAN can have one port, and the
port will not communicate to the others.
4.
The ports you clicked now are in the same VLAN, you also can delete some ports
from the VLAN with click the ports again, such as P4.
Caution:When the workstation connect to another port, the administrator must reassign
VLAN members, when TRUNK is on, all ports in a TRUNK should be in the same VLAN.
Tag-based VLAN setting:
The difference is setting parameters between Port-based VLAN and Tag-based VLAN,
you can set the PVID and emigration rule. ( VLAN 1 to VLAN 9’s VID are 1-9).
Default Setting: PVID is 1, emigration rule are Untag.
1.
Select “Tag VLAN” in VLAN dialog box, and enter the interface. VLAN member set
on a same method to Port-based VLAN.
- 19 -
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-SF2109P/TL-SF2117P/TL-SL2226P Ethernet Smart Switch User Guide
2.
Setting parameter, pick the PVID and emigration rule in combo box.
4.6 Priority
1.
Click the priority button in setting menu, or the “Priority over ToS and VLAN Tag”
icon.
2.
The Switch support only port-based priority, there are two level priority: Low and
High, you can set it in Port Status. “1 : n” means low priority and high priority, “0 : 1”
- 20 -
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-SF2109P/TL-SF2117P/TL-SL2226P Ethernet Smart Switch User Guide
means that high priority is first always.
4.7 MAC Address Age Time
The MAC Address will auto age out after 5 minutes if it is not updated in MAC address
table, this time is aging time. TL-SF2109’s aging time is 300s. TL-SF2117P’s is 0s to
1,048,575s. TL-SL2226P’s is 12s or 300s.
1.
Click the “MAC Address Aging” in settings menu or the “MAC Address Aging
Setting” icon.
- 21 -
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-SF2109P/TL-SF2117P/TL-SL2226P Ethernet Smart Switch User Guide
2.
You can select as follows.
4.8 Config effect
1.
Write to Switch
After finishing setting above, click “write to Switch”, the switch will restart and reserve the
results having been configed.
2.
Restore factory setting
Click the “Recover Factory Configuration” in menu, and it will restore the parameters to
default value and restart the switch.
- 22 -
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-SF2109P/TL-SF2117P/TL-SL2226P Ethernet Smart Switch User Guide
4.9 “Save”, “Open” Configuration file
1.
“Save” configuration is that save the result of current configuration to a file.
2.
“Open” configuration is that open the last saved file.
- 23 -
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-SF2109P/TL-SF2117P/TL-SL2226P Ethernet Smart Switch User Guide
- 24 -
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-SF2109P/TL-SF2117P/TL-SL2226P Ethernet Smart Switch User Guide
Appendix A: TL-SF2109P Technical Specification
General
Standards
IEEE802.3 10BASE-T
IEEE802.3u 100BASE-TX/FX
Topology
Protocol
Ports
Star
CSMA/CD
8 10/100M Auto-Negotiation RJ45 Ports (Auto MDI/MDIX)
1 Independent Expansion Slot
1 Console (RS232 DB9 Male)
Data Transfer Rate
Ethernet: 10Mbps (Half Duplex), 20Mbps (Full Duplex);
Fast Ethernet: 100Mbps (Half Duplex), 200Mbps (Full Duplex)
10BASE-T: UTP category 3, 4, 5 cable (maximum 100m)
EIA/TIA-568 100Ω STP (maximum 100m)
100BASE-TX: UTP category 5, 5e cable (maximum 100m)
EIA/TIA-568 100Ω STP (maximum 100m)
100BASE-FX: MMF (maximum 2000m) or SMF (maximum
20~60Km)
Network Media (Cable)
LED indicators
Power, Link/Act, 100Mbps
Transfer Method
Frame Filtering and
Forward Rate
Store-and-Forward
10Mbps: 14880pps, 100Mbps: 148800pps
220V~, 50Hz
Power Supply Input
100Base-FX Multi-Mode Fiber Module
TL-SM201CM
（SC connector，up to 2km）
Optional Module
100Base-FX Single-Mode Fiber Module
TL-SM201CS-20/40/60
（SC connector，up to 20/40/60km）
Environmental and Physical
Dimensions(W×D×H) 11.6×6.2×1.7 in. (294×158×44mm)
Operating
0℃~40℃ (32℉~104℉)
Temperature
Storage Temperature
Operating Humidity
Storage humidity
-40~70℃ (-40℉~158℉)
10%~90% non-condensing
5%~95% non-condensing
- 25 -
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-SF2109P/TL-SF2117P/TL-SL2226P Ethernet Smart Switch User Guide
Appendix B: TL-SF2117P Technical Specification
General
Standards
IEEE802.3 10BASE-T
IEEE802.3u 100BASE-TX/FX
Topology
Protocol
Ports
Star
CSMA/CD
16 10/100M Auto-Negotiation RJ45 Ports (Auto MDI/MDIX)
1 Independent Expansion Slot
1 Console (RS232 DB9 Male)
Data Transfer Rate
Ethernet: 10Mbps (Half Duplex), 20Mbps (Full Duplex);
Fast Ethernet: 100Mbps (Half Duplex), 200Mbps (Full Duplex)
10BASE-T: UTP category 3, 4, 5 cable (maximum 100m)
EIA/TIA-568 100Ω STP (maximum 100m)
100BASE-TX: UTP category 5, 5e cable (maximum 100m)
EIA/TIA-568 100Ω STP (maximum 100m)
100BASE-FX: MMF (maximum 2000m) or SMF (maximum
20~60Km)
Network Media (Cable)
LED indicators
Power, Link/Act, 100Mbps
Transfer Method
Frame Filtering and
Forward Rate
Store-and-Forward
10Mbps: 14880pps, 100Mbps: 148800pps
100-240V~, 50/60Hz
Power Supply Input
100Base-FX Multi-Mode Fiber Module
TL-SM201CM
（SC connector，up to 2km）
Optional Module
100Base-FX Single-Mode Fiber Module
TL-SM201CS-20/40/60
（SC connector，up to 20/40/60km）
Environmental and Physical
Dimensions(W×D×H) 17×7.1×1.7 in. (440×180×44mm)
Operating
0℃~40℃ (32℉~104℉)
Temperature
Storage Temperature
Operating Humidity
Storage humidity
-40~70℃ (-40℉~158℉)
10%~90% non-condensing
5%~95% non-condensing
- 26 -
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-SF2109P/TL-SF2117P/TL-SL2226P Ethernet Smart Switch User Guide
Appendix C: TL-SL2226P Technical Specification
General
Standards
IEEE802.3 10BASE-T
IEEE802.3u 100BASE-TX/FX
IEEE802.3ab 1000BASE-T
IEEE802.3Z 1000BASE-SX/LX
Star
Topology
Protocol
Ports
CSMA/CD
8 10/100M Auto-Negotiation RJ45 Ports (Auto MDI/MDIX)
1 Independent Expansion Slot
1 Console (RS232 DB9 Male)
Data Transfer Rate
Ethernet: 10Mbps (Half Duplex), 20Mbps (Full Duplex);
Fast Ethernet: 100Mbps (Half Duplex), 200Mbps (Full Duplex)
Gigabit Ethernet: 1000Mbps (Half Duplex), 2000Mbps (Full
Duplex)
Network Media (Cable)
10BASE-T: UTP category 3, 4, 5 cable (maximum 100m)
EIA/TIA-568 100Ω STP (maximum 100m)
100BASE-TX/1000Base-T: UTP category 5, 5e cable
(maximum 100m)
EIA/TIA-568 100Ω STP
(maximum 100m)
100BASE-FX/1000BASE-SX/LX: MMF or SMF
Power, Link/Act, 100Mbps
LED indicators
Transfer Method
Frame Filtering and
Forward Rate
Store-and-Forward
10Mbps: 14880pps, 100Mbps: 148800pps
100-240V~, 50/60Hz
Power Supply Input
100Base-TX UTP module, RJ45 Port,
Optional Module
TL-SM201U
100m max
100Base-TX MMF module, IEEE
TL-SM201CM
suggested SC connector, 2Km max
100Base-TX SMF module, IEEE
TL-SM201CS
suggested SC connector, 60Km max
1000Base-T UTP module, RJ45 Port,
TL-SM301U
100m max
1000Base-SX MMF module, IEEE
suggested SC connector,
TL-SM301CM
（50/125μm: 550m max; 62.5/125μ
m: 275m max）
1000Base-LX SMF module, IEEE
TL-SM301CS
suggested SC connector, 10Km max
- 27 -
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-SF2109P/TL-SF2117P/TL-SL2226P Ethernet Smart Switch User Guide
1000Base-LX or 1000Base-SX GBIC
TL-SM301GB
module
Environmental and Physical
Dimensions(W×D×H) 17×7.1×1.7in. (440×180×44mm)
Operating
0℃~40℃ (32℉~104℉)
Temperature
Storage Temperature
Operating Humidity
Storage humidity
-40~70℃ (-40℉~158℉)
10%~90% non-condensing
5%~95% non-condensing
- 28 -
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-SF2109P/TL-SF2117P/TL-SL2226P Ethernet Smart Switch User Guide
Appendix D: Contact Information
For help with the installation or operation of the TP-LINK TL-SF2109P/2117P or
TL-SL2226P Smart Switch, please contact us.
E-mail: [email protected]
Website: http://www.tp-link.com
- 29 -
Download from Www.Somanuals.com. All Manuals Search And Download.
|