Enterprise Networking Solution
Installation Guide
10/100Mbps Unmanaged Switch
TL-SF1016DS/TL-SF1016
TL-SF1024D/TL-SF1024
TL-SF1048
Download from Www.Somanuals.com. All Manuals Search And Download.
Related Document
This Installation Guide is also available in PDF on our website. To obtain the latest
documentation and prodcut information, please visit our official website:
About this Installation Guide
This Installation Guide describes the hardware characteristics, installation methods
and the points that should be attended to during installation. This Installation
Guide is structured as follows:
Chapter 1 Introduction. This chapter describes the external components of
the switch.
Chapter 2 Installation. This chapter illustrates how to install the switch.
Chapter 3 Lightning Protection. This chapter illustrates how to prevent
lightning damage.
Chapter 4 Connection. This chapter illustrates how to do the physical connec-
tion of the switch.
Appendix A Troubleshooting.
Appendix B Hardware Specifications.
Appendix C Technical Support.
Audience
This Installation Guide is for:
Network Engineer
Network Administrator
Conventions
Due to the similarity in structure of TL-SF1016DS/TL-SF1016/TL-SF1024D/
TL-SF1024/TL-SF1048 10/100Mbps Unmanaged Switch series, in this Installation
Guide we take TL-SF1016 as an example to illustrate Chapter 2 Installation,
Chapter 3 Lighting Protection and Chapter 4 Connection.
This Guide uses the specific formats to highlight special messages. The following
table lists the notice icons that are used throughout this guide.
Remind to be careful. A caution indicates a potential which may result in
device damage.
Remind to take notice. The note contains the helpful information for a
better use of the product.
Related Document
II
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Chapter 1 Introduction ——————————— 01
1.1
1.2
1.3
Product Overview...................................................................01
Features......................................................................................01
Appearance...............................................................................01
Chapter 2 Installation ———————————— 04
2.1
2.2
2.3
2.4
Package Contents...................................................................04
Safety Precautions..................................................................04
Installation Tools......................................................................06
Product Installation................................................................07
Chapter 3 Lightning Protection ———————— 09
3.1
3.2
3.3
3.4
Cabling Reasonably................................................................09
Connect to Ground.................................................................11
Equipotential Bonding..........................................................12
Use Lightning Arrester..........................................................13
Chapter 4 Connection ——————————— 15
4.1
4.2
4.3
4.4
Ethernet Port ............................................................................15
Verify Installation ....................................................................15
Power On....................................................................................15
Initialization ..............................................................................16
Appendix A Troubleshooting ————————— 16
Appendix B Hardware Speciꢀcations —————— 17
Appendix C Technical Support ————————— 18
III
Contents
Download from Www.Somanuals.com. All Manuals Search And Download.
10/100Mbps Fast Ethernet Switch
ChaCter C Introduction
C1C Product Overview
TL-SF1016/TL-SF1016DS/TL-SF1024/TL-SF1024D/TL-SF1048 switch provides 16/24/48
10/100Mbps Auto-Negotiation RJ45 ports. Each port of the TL-SF1016/TL-SF1016DS/
TL-SF1024/TL-SF1024D/TL-SF1048 supports auto MDI/MDI-X function, eliminating the
need for crossover cables or Uplink ports. The switch is Plug-and-Play and any port can be
simply plugged into a server, a hub or a switch, using straight cable or crossover cable.
The TL-SF1016/TL-SF1016DS/TL-SF1024/TL-SF1024D/TL-SF1048 16/24/48-port
10/100Mbps Fast Ethernet Switch provides you with a low-cost, easy-to-use, high-
performance, seamless and standard upgrade to improve your old network to a
100Mbps network. It will boost your network performance up to full duplex data
transfer.
C11 Features
¾ Complies with IEEE802.3, IEEE802.3u standards
¾ 16/24/48 10/100Mbps Auto-Negotiation RJ45 ports supporting Auto- MDI/MDIX
¾ Supports IEEE802.3X flow control for full-duplex mode and backpressure for half-
duplex mode
¾ LED indicators for monitoring power, link, activity, speed
¾ Rack-mountable steel case
¾ Internal power supply
C11 ACCearance
■
Front Panel
The front panel of The TL-SF1016 is shown as the following figure.
LEDs
10/100Mbps RJ45 Port
Figure 1-1 Front Panel of TL-SF1016
The front panel of The TL-SF1016DS is shown as the following figure.
Introduction
01
Download from Www.Somanuals.com. All Manuals Search And Download.
10/100Mbps Fast Ethernet Switch
LEDs
10/100Mbps RJ45 Port
Figure 1-2 Front Panel of TL-SF1016DS
The front panel of The TL-SF1024 is shown as the following figure.
LEDs
10/100Mbps RJ45 Port
Figure 1-3 Front Panel of TL-SF1024
The front panel of The TL-SF1024D is shown as the following figure.
LEDs
10/100Mbps RJ45 Port
Figure 1-4 Front Panel of TL-SF1024D
The front panel of The TL-SF1048 is shown as the following figure.
LEDs
10/100Mbps RJ45 Port
Figure 1-5 Front Panel of TL-SF1048
LEDs
LED
Status
On
Indication
The switch is powered on
Power
Off
The switch is powered off or power supply is abnormal
Power supply is abnormal
Flashing
On
A device is linked to the corresponding port
Data is being transmitted or received
There is no device linked to the corresponding port
The corresponding port is running at 100Mbps
Link/Act
Flashing
Off
On
100Mbps
There is no device linked to the corresponding port or
the port is running at 10Mbps
Off
Note: Because of the difference among the switch models, some switches don’t have
the 100Mbps indicator, such as TL-SF1048, TL-SF1016DS and TL-SF1024D switch.
Introduction
02
Download from Www.Somanuals.com. All Manuals Search And Download.
10/100Mbps Fast Ethernet Switch
10/100Mbps Por
t
Designed to connect to the device with a bandwidth of 10Mbps or 100Mbps. Each
has a corresponding 10/100Mbps LED.
■
Rear Panel
The rear panel of the switch is shown as the following figure.
Grounding Terminal
Power Socket
Figure 1-6 Rear Panel
Grounding Terminal
The switch already comes with lightning protection mechanism. You can also ground
the switch through the PE (Protecting Earth1 cable of AC cord or with Ground Cable.
For detailed information, please refer to Chapter 3 Lightning Protection.
Power Socket
Connect the female connector of the power cord here, and the male connector to
the AC power outlet. Please make sure the voltage of the power supply meets the
requirement of the input voltage.
Caution: Please use the provided power cord.
Introduction
03
Download from Www.Somanuals.com. All Manuals Search And Download.
10/100Mbps Fast Ethernet Switch
ChaCter 1 Installation
11C Package Contents
Make sure that the package contains the following items. If any of the listed items is
damaged or missing, please contact your distributor.
One Switch
One Power Cord
This Installation Guide
Two mounting brackets and the
fittings
111 Safety Precautions
To avoid any device damage and bodily injury caused by improper use, please observe
the following rules.
■
Safety Precautions
■
Keep the power off during the installation.
■
Wear an ESD-preventive wrist strap, and make sure that the wrist strap has a good
skin contact and is well grounded.
■
Use only the power cord provided with the device.
■
Make sure that the supply voltage matches the specifications indicated on the rear
panel of the device.
■
Ensure the vent hole is well ventilated and unblocked.
■
Do not open or remove the cover of the device.
■
Before cleaning the device, cut off the power supply. Do not clean it by the waterish
cloth, and never use any other liquid cleaning method.
Introduction
04
Download from Www.Somanuals.com. All Manuals Search And Download.
10/100Mbps Fast Ethernet Switch
■
Site Requirements
Temperature/Humidity
ꢀꢁȭ
ꢁȭ
Please keep a proper temperature and humidity in the equipment room. Too high/low
humidity may lead to bad insulation, electricity leakage, mechanical property changes
and corrosions. Too high temperature may accelerate aging of the insulation materials
and can thus significantly shorten the service life of the device. For normal temperature
and humidity of the device, please check the following table.
Environment
Operating
Storage
Temperature
0℃ ~ 40℃
Humidity
10% ~ 90%RH Non-condensing
5% ~ 90%RH Non-condensing
-40℃ ~ 70℃
Clearness
The dust accumulated on the device can be absorbed by static electricity and result
in poor contact of metal contact points. Some measures have been taken for the
device to prevent static electricity, but too strong static electricity can cause deadly
damage to the electronic elements on the internal circuit board. To avoid the effect of
static electricity on the operation of the device, please attach much importance to the
following items:
■
Dust the device regularly, and keep the indoor air clean.
■
Keep the device well grounded and ensure static electricity has been transferred.
Electromagnetic Interference
Electronic elements including capacitance and inductance on the device can be affected
by external interferences, such as conducted emission by capacitance coupling,
inductance coupling, and impedance coupling. To decrease the interferences, please
make sure to take the following measures:
■
Use the power supply that can effectively filter interference from the power grid.
■
Keep the device far from high-frequency, strong-current devices, such as radio
transmitting station.
■
Use electromagnetic shielding when necessary.
Installation
05
Download from Www.Somanuals.com. All Manuals Search And Download.
10/100Mbps Fast Ethernet Switch
Lightening Protection
Extremely high voltage currents can be produced instantly when lightning occurs and the air
in the electric discharge path can be instantly heated up to 20,000℃. As this instant current
is strong enough to damage electronic devices, more effective lightning protection measures
should be taken.
■
Ensure the rack and device are well earthed.
■
Make sure the power socket has a good contact with the ground.
■
Keep a reasonable cabling system and avoid induced lightning.
■
Use the signal SPD (Surge Protective Device1 when wiring outdoor.
Note: For detailed lightning protection measures, please refer to Chapter 3
Lightning Protection.
Installation Site
ꢀꢁꢂS
When installing the device on a rack or a flat workbench, please note the following
items:
■
The rack or workbench is flat and stable, and sturdy enough to support the weight
of 5.5kg at least.
■
The rack or workbench has a good ventilation system. The equipment room is well
ventilated.
■
The rack is well grounded. Keep the power socket less than 1.5 meters away from
the device.
111 Installation Tools
■
■
■
Phillips screwdriver
ESD-preventive wrist wrap
Cables
Installation
06
Download from Www.Somanuals.com. All Manuals Search And Download.
10/100Mbps Fast Ethernet Switch
Note: These tools are not provided with our product. If needed, please self purchase
them.
112 Product Installation
■
Desktop Installation
To install the device on the desktop, please follow the steps:
1. Set the device on a flat surface strong enough to support the entire weight of the
device with all fittings.
2. Remove the adhesive backing papers from the rubber feet.
3. Turnover the device and attach the supplied rubber feet to the recessed areas on
the bottom at each corner of the device.
Feet
Bottom of the Device
Notch
Figure 2-1 Desktop Installation
■
Rack Installation
To install the device in an EIA standard-sized, 19-inch rack, follow the instructions
described below:
1. Check the grounding and stability of the rack.
2. Secure the supplied rack-mounting brackets to each side of the device with supplied
screws, as illustrated in the following figure.
Rack-mounting Bracket
Screw
Figure 2-2 Bracket Installation
Installation
07
Download from Www.Somanuals.com. All Manuals Search And Download.
10/100Mbps Fast Ethernet Switch
3. After the brackets are attached to the device, use suitable screws (not provided1 to
secure the brackets to the rack, as illustrated in the following figure.
Rack
Figure 2-3 Rack Installation
Caution:
■
Please set 5~10cm gaps around the device for air circulation.
Please avoid any heavy thing placed on the device.
■
■
Please mount devices in sequence from the bottom to top of the rack and ensure a
certain clearance between devices for the purpose of heat dissipation.
Installation
08
Download from Www.Somanuals.com. All Manuals Search And Download.
10/100Mbps Fast Ethernet Switch
ChaCter 1 Lightning Protection
11C Cabling Reasonably
In the actual network environment, you may need cable outdoors and indoors, and
the requirements for cabling outdoors and indoors are different. A reasonable cabling
system can decrease the damage of induced lightning to devices.
Note: It's not recommended using Ethernet cables outdoors. When cabling outdoors,
please use a signal lightning arrester.
■
Requirements for Cabling Outdoors
■
Aerial cabling without safeguard is not allowed.
■
It’s not allowed cabling down the building to connect network devices in different
floors.
■
Outdoor cables should be buried and paved to the indoor through basement. A
piece of steel wire should be paved underground along the pipe and connected to
the lightning protection terminal of the building for shielding. Before connecting the
cable to the device, install a signal lightning arrester on the corresponding port.
■
When an aerial cable is set up, the cable should be through a metal pipe (15m long
at least1 before coming into the building. The two ends of this metal pipe should
be grounded. Before connecting the cable to the device, install a signal lightning
arrester on the corresponding port.
■
It’s not necessary to pave STP cables through pipes. The shielded layer of STP cable
should be well grounded. Before connecting the cable to the device, install a signal
lightning arrester on the corresponding port.
Lightning Protection
Download from Www.Somanuals.com. All Manuals Search And Download.
09
10/100Mbps Fast Ethernet Switch
■
Requirements for Cabling Indoors
When cabling indoors, keep a certain distance away from the devices that may cause
high-frequency interferences, such as down-conductor cable, powerline, power
transformer and electromotor.
■
The main cable should be paved in the metal raceway of the access shaft. When
cabling, keep the loop area formed by the cable itself as small as possible.
■
Requirements for the distance between Ethernet cable and other pipelines are
shown in the table.
Ethernet Cable
Other Pipelines
Min Parallel Net Length L
Min Parallel-overlapping
Net Height H (mm1
(mm1
Down-conductor
PE
1000
50
300
20
Service pipe
150
150
500
300
300
20
Compressed air pipe
Thermal pipe (not wrapped1
Thermal pipe (wrapped1
Gas pipe
20
500
300
20
The two diagrams below demonstrate parallel net length and parallel-overlapping net
height.
Note: The above minimum net length/height is required when metal raceway is not
used. If any requirements cannot be met, you can add a steel tube or metal raceway
for shielding.
■
Requirements for the distance between Ethernet cable and high-power electric
devices are in following tables.
Min Parallel
Length (mm1
Cable
Pave Way
Parallel cabling
130
70
<2kVA
One is in the grounded metal raceway or metal pipe
powerline
The both are in the grounded metal raceway or metal
pipe
10
10
Lightning Protection
Download from Www.Somanuals.com. All Manuals Search And Download.
10/100Mbps Fast Ethernet Switch
Parallel cabling
300
2~5kVA
powerline
One is in the grounded metal raceway or metal pipe
150
80
The both are in the grounded metal raceway or metal
pipe
Parallel cabling
600
300
>5kVA
One is in the grounded metal raceway or metal pipe
powerline
The both are in the grounded metal raceway or metal
pipe
150
Device
Min Distance (m1
Switch case
1.00
Transformer room
Elevator tower
2.00
2.00
2.00
Air-conditioner room
111 Connect to Ground
Connecting the device to ground is to quickly release the lightning over-voltage and
over-current of the device, which is also a necessary measure to protect the body from
electric shock.
In different environments, the device may be grounded differently. The following
will instruct you to connect the device to the ground in two ways, connecting to the
grounding bar or connecting to the ground via the power cord. Please connect the
device to ground in the optimum way according to your specific operation environment.
■
Connecting to the Grounding Bar
If the device is installed in the Equipment Room, where a grounding bar is available,
you are recommended to connect the device to the grounding bar as shown in the
following figure.
Grounding Te rminal
Grounding Bar
Device (Rear Panel)
Ground Cable
Figure 3-1 Connecting to the Grounding Bar
Lightning Protection
Download from Www.Somanuals.com. All Manuals Search And Download.
11
10/100Mbps Fast Ethernet Switch
Note: The grounding bar and the ground cable are not provided with our product. If
needed, please self purchase them.
■
Connecting to the Ground via the Power Supply
If the device is installed in the normal environment, the device can be grounded via the
PE (Protecting Earth1 cable of the AC power supply as shown in the following figure.
Figure 3-2 Connecting to the Ground
Note:
■
The figure is to illustrate the application and principle. The power plug you get from
the package and the socket in your situation will comply with the regulation in your
country, so they may differ from the figure above.
If you intend to connect the device to the ground via the PE (Protecting Earth1 cable
■
of AC power cord, please make sure the PE (Protecting Earth1 cable in the electrical
outlet is well grounded in advance.
111 EquiCotential Bonding
Equipotential Bonding is the practice of intentionally electrically connecting all earthed
systems to the same grounding grid or connecting the grounding grids of all the
earthed systems together through the ground or overground metal so as to create
an earthed equipotential zone. When lightning occurs, the high voltage produced by
lightning current in all systems will meanwhile exist in their ground cables, and thus
all ground cables have the same electrical potential and basically eliminate the electric
strikes between the systems.
The figure below illustrates how to practice equipotential bonding in a network.
Lightning Protection
Download from Www.Somanuals.com. All Manuals Search And Download.
12
10/100Mbps Fast Ethernet Switch
Grounding Te rminal
Ground Cable
Equipotential Bonding Cable
Grounding Bar
Figure 3-3 Equipotential Bonding
When equipotential bonding, please note that the cable should be copper wrapped
Kelly with its area being 6mm2 at least. The shorter cable the better, and use a
grounding bar to establish an equipotential bonding point.
Note: The equipotential bonding cable is not provided with our product. If needed,
please self purchase it.
112 Use Lightning Arrester
Power lightning arrester and signal lightning arrester are used for lighting protection.
Power lightning arrester is used for limiting the voltage surge due to a lightning. If an
outdoor AC power cord should be directly connected to the device, please use a power
lightning arrester.
Note: Power lightning arrester is not provided with our product. If needed, please self
purchase it.
Lightning Protection
Download from Www.Somanuals.com. All Manuals Search And Download.
13
10/100Mbps Fast Ethernet Switch
Signal lightning arrester is used to protect RJ45 ports of the device from lightning.
When cabling outdoors, please install a signal lightning arrester before connecting the
cable to the device.
When purchasing or using a signal lightning arrester, please observe the following
rules:
■
The port rate of the signal lightning arrester should match the rate of the desired
port on the device. If it is not matched, this signal lighting arrester will not work.
Purchase a standard lightning arrester.
■
Install signal lightning arrester near the protected device and connect it to the
ground via a shorter ground cable.
Grounding Te rminal
Equipotential Bonding Cable
Device
Ethernet Cable
Signal Lightning Arrester
Figure 3-4 Equipotential Bonding
Note: Signal lightning arrester is not provided with our product. If needed, please self
purchase it.
Lightning Protection
Download from Www.Somanuals.com. All Manuals Search And Download.
14
10/100Mbps Fast Ethernet Switch
ChaCter 2 Connection
21C Ethernet Port
Connect the Ethernet ports of the switch to the network devices by RJ45 cable as the
following figure shown.
RJ45 Cable
RJ45 Port
Figure 4-1 Connecting the Ethernet Port
211 Verify Installation
After completing the installation, please verify the following items:
■
There are 5~10cm of clearance around the sides of the device for ventilation and
the air flow is adequate.
■
■
■
The voltage of the power supply meets the requirement of the input voltage of the device.
The power socket, device and rack are well grounded.
The device is correctly connected to other network devices.
211 Power On
Plug in the negative connector of the provided power cord into the power socket of the
device, and the positive connector into a power outlet as the following figure shown.
Figure 4-2 Connecting to Power Supply
Connection
15
Download from Www.Somanuals.com. All Manuals Search And Download.
10/100Mbps Fast Ethernet Switch
Note: The figure is to illustrate the application and principle. The power plug you get
from the package and the socket in your situation will comply with the regulation in
your country, so they may differ from the figure above.
212 Initialization
After the device is powered on, it begins the Power-On Self-Test. A series of tests run
automatically to ensure the device functions properly. During this time, its LED indica-
tors will respond as follows:
■
All of the LED indicators will flash momentarily for one second, which represents a
resetting of the system.
■
The Power LED indicator will light up.
ACCendix A Troubleshooting
QQQQ The Power LED is not lit
The Power LED should be lit up when the power system works normally. If
the Power LED is not lit, please check as follows:
1. Make sure the AC power cord connected the switch with power source
properly.
2. Make sure the voltage of the power supply meets the requirement of the
input voltage of the switch.
3. Make sure the power source is ON.
QQQQ The Link/Act LED is not lit when a device is connected to the
corresConding Cort
You are recommended to check the following items:
1. Make sure that the cable connectors are firmly plugged into the Switch
and the device.
2. Make sure the connected device is turned on and working well.
3. The cable must be less than 100 meters long (328 feet1.
16
Connection
Download from Www.Somanuals.com. All Manuals Search And Download.
10/100Mbps Fast Ethernet Switch
ACCendix B Hardware SCecifications
Item
Content
IEEE 802.3 10Base-T
IEEE 802.3u 100Base-TX
IEEE 802.3x Flow Control
Standards
10Base-T: UTP/STP of Cat. 3 or above(maximum 100m1
100Base-TX: UTP/STP of Cat. 5 or above(maximum 100m1
FCC, CE
Transmission Medium
Safety & Emissions
Transfer Method
Store-and-Forward
MAC Address Learning Automatically learning, automatically aging
10Base-T: 14881pps/Port
Frame Forward Rate
100Base-Tx: 148810pps/Port
LEDs
Power, Link/Act, 100Mbps
~
Operating Temperature 0℃ 40℃
~
Storage Temperature
Operating Humidity
Storage Humidity
-40℃ 70℃
~
10% 90%RH Non-condensing
~
5% 90%RH Non-condensing
17
Hardware Specifications
Download from Www.Somanuals.com. All Manuals Search And Download.
10/100Mbps Fast Ethernet Switch
ACCendix C Technical SuCCort
■
■
To download the latest Firmware, Driver, Utility and User Guide, please go to:
■
For all other technical support, please contact us by using the following details:
Global
Tel: +86 755 2650 4400
Fee: Depending on rate of different carriers, IDD.
E-mail: [email protected]
Service time: 24hrs, 7 days a week
Australia/New Zealand
Tel: AU 1300 87 5465 (Depending on 1300 policy1
NZ 0800 87 5465 (Toll Free1
E-mail: [email protected] (Australia1
[email protected] (New Zealand1
Service time: 24hrs, 7 days a week
Brazil
Toll Free: 0800 608 9799 (Portuguese Service1
E-mail: [email protected]
Service time: Monday to Saturday, 09:00 to 20:00; Saturday, 09:00 to
15:00
France
Tel: 0820 800 860 (French service1
Fee: 0.118 EUR/min from France
Email: [email protected]
Service time: Monday to Friday 9:00 to 18:00 *Except French Bank
holidays
Germany/Austria
Tel: +49 1805 875 465 (German Service1
+49 1805 TPLINK
+49 820 820 360
Fee: Landline from Germany: 0.14EUR/min.
Landline from Austria: 0.20EUR/min.
E-mail: [email protected]
Service time: Monday to Friday, 9:00 to 12:30 and 13:30 to 17:30.
GMT+ 1 or GMT+ 2 (DST in Germany1 *Except bank holidays in Hesse
Indonesia
Italy
Tel: (+621 021 6386 1936
Fee: Depending on rate of different carriers.
E-mail: [email protected]
Service time: Monday to Friday 9:00 to 18:00 *Except public holidays
Tel: +39 023 051 9020
Fee: Depending on rate of different carriers.
E-mail: [email protected]
Service time: Monday to Friday, 9:00 to13:00 and 14:00 to 18:00
Malaysia
Poland
Toll Free: 1300 88 875 465
Email: [email protected]
Service time: 24hrs, 7 days a week
Tel: +48 (01 801 080 618
+48 223 606 363 (if calls from mobile phone1
Fee: Depending on rate of different carriers.
E-mail: [email protected]
Service time: Monday to Friday 9:00 to 17:00. GMT+1 or GMT+2 (DST1
18
Technical Support
Download from Www.Somanuals.com. All Manuals Search And Download.
10/100Mbps Fast Ethernet Switch
Russian Federation
Tel: 8 (4991 754 5560 (Moscow NO.1
8 (8001 250 5560 (Toll-free within RF1
E-mail: [email protected]
Service time: From 9:00 to 21:00 (Moscow time1
*Except weekends and holidays in RF
Singapore
Tel: +65 6284 0493
Fee: Depending on rate of different carriers.
E-mail: [email protected]
Service time: 24hrs, 7 days a week
Switzerland
Tel: +41 (01 848 800 998 (German Service1
Fee: 4-8 Rp/min, depending on rate of different time.
E-mail: [email protected]
Service time: Monday to Friday, 9:00 to 12:30 and 13:30 to 17:30.
GMT+ 1 or GMT+ 2 (DST1
Turkey
UK
Tel: 0850 7244 488 (Turkish Service1
Fee: Depending on rate of different carriers.
E-mail: [email protected]
Service time: 9:00 to 21:00, 7 days a week
Tel: +44 (01 845 147 0017
Fee: Landline: 1p-10.5p/min, depending on the time of day.
Mobile: 15p-40p/min, depending on your mobile network.
E-mail: [email protected]
Service time: 24hrs, 7 days a week
Ukraine
Tel: 0800 505 508
Fee: Free for Landline; Mobile: Depending on rate of different carriers.
E-mail: [email protected]
Service time: Monday to Friday 10:00 to 22:00
USA/Canada
Toll Free: +1 866 225 8139
E-mail: [email protected]
Service time: 24hrs, 7 days a week
19
Technical Support
Download from Www.Somanuals.com. All Manuals Search And Download.
E-mail: [email protected]
7106504436
REV4.0.0
Download from Www.Somanuals.com. All Manuals Search And Download.
|