User's Guide
TR-966D
10/100Mbps WDM Fiber Bridge
Download from Www.Somanuals.com. All Manuals Search And Download.
COPYRIGHT & TRADEMARKS
Table of Content
Specifications are subject to change without notice.
is a registered trademark of TP-LINK
Technologies Co., Ltd. Other brands and product names
are trademarks or registered trademarks of their respective
holders.
No part of the specifications may be reproduced in any form
or by any means or used to make any derivative such as
translation, transformation, or adaptation without permission
from TP-LINK Technologies Co., Ltd. Copyright @2006 TP-
LINK Technologies Co., Ltd. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
Auto-detection of half/full duplex transfer mode for RJ45
port.
TR-966D
10/100M WDM Fiber Bridge
Auto-negotiation of 10/100Mbps rate and Auto-MDIX for
RJ45 port.
TR-966D Front Panel
Fiber port only support full duplex transfer.
Extend fiber distance up to 20km for fiber port.
Easy-to-view LED indicators provide status to easily monitor
network activity.
2. Rear Panel
The rear panel of the TR-966D consists of one AC power
connector, two 10/100Mbps RJ45 ports and two SC Fiber
interfaces.
External power supply.
Network Cable Supported
POWER
T1
T2
F1
F2
The connectors and network cables supported by the TR-966D
are listed in the following:
TR-966D Rear Panel
3. LED Indicators
RJ45 port: Cat 5 Twisted-pair
This TR-966D has LED indicators which can provide a real-
time report. When you take a look at these indicators, you will
know what’s happening your network.
SC Fiber port: single-mode fiber cable
Appearance Indication
1. Front Panel
Power(Red): Lights when the adapter is properly plugged in.
T1_SPD/T2_SPD(Green): Light when the RJ45 port is
connected to 100Mbps device; When the port connect to
a 10Mbps device, the LED turns off.
The front panel of the TR-966D consists of several LED
indicators
2
3
Download from Www.Somanuals.com. All Manuals Search And Download.
T1_Link/ Act/ T2_Link/ Act(Green): Steady green
indicates that a valid link exists. Flashing green indicates
that the TR-966D is receiving or transmitting data from the
RJ-45 port.
Make sure that the length of twisted pair cable (Category-
5) between 10/100Base-TX device and converter is not
longer than 100 meters.
Connect one end of twisted pair cable to RJ45 jack on the
TR-966D and the other end of the cable to the cable to
the RJ-45 jack on the 10/100Base-TX device.
F1_Link/Act/ F2_Link/Act (Green): Steady green
indicates that a valid link exists. Flashing green indicates
that the TR-966D is receiving or transmitting data from
the fiber port.
B. Connect the TR-966D to 100Base-FX Device
Connection.
Connect on (SC) end of a singl-mode fiber cable to the SC
connector F1/F2 on the TR-966D and the other end of
the cable to 100Base-FX device.
Installation Guide
1. Configuration
In order to achieve the aim of effectively expanding a Fast
Ethernet network, you can use the TR-966D as the example.
C. Turn on the device.
Notes:
The WDM technology employs passive optic multiplexing,
thus multiplex the transmit (TX) and receive (RX) lines onto a
single fiber. WDM technology is implemented in couples. For
example, one site uses the F1 fiber port on the TR-966D, the
other site uses DEVICE A, the fiber port on DEVICE A must be
1550nm/1310nm WDM fiber; One site uses the F2 fiber port on
the TR-966D, the other site uses DEVICE B, the fiber port on
DEVICE B must be 1310nm/1550nm WDM fiber.
2. Installation procedure:
A.
Connect the TR-966D to 10/100Base-TX Device (Hub or
Switch).
4
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix Specification
General
Standard
IEEE 802.3 10Base-T
IEEE 802.3u 100Base-TX/100Base-FX
Topology
Protocol
Star
CDMA/CD
Data Transfer Ethernet: 10Mbps(Half Duplex);
Rate
20Mbps(Full Duplex)
Fast Ethernet: 100Mbps(Half Duplex);
200Mbps(Full Duplex)
Ports
2 10/100Mbps RJ-45 ports
2 SC Fiber ports
( F1: 1310/1550 nm Single- mode single Fiber
F2: 1550/1310 nm Single-mode single Fiber)
LED indicator POWER Power on
Each port RJ45 port:10/100Mbps Link/Act
and 100Mbps speed LED
Fiber port: 100Mbps Link/Act
Network
Medium
RJ45 port: Cat. 5 Twist-pair
SC Fiber port: single-mode fiber cable
Max. Distance Twisted pair (Cat.5): 100m
Single-mode fiber cable: 20km
Environmental and Physical
Power
Dimension(LxWxH) 122mmx76mmx24mm
Environment Operating temperature: 0ºC ~ 40ºC
Power Adapter (9V, 0.8A)
Storage temperature: -20ºC ~ 70ºC
TP-LINK TECHNOLOGIES CO.,LTD.
Humidity: 5% ~ 90% RH
E-mail:[email protected]
Add:3/F.,Buiding R1-B,Hi-tech Industrial Park,Shennan Rd.,Shenzhen,P.R.China
6
Download from Www.Somanuals.com. All Manuals Search And Download.
|