TD-8610/TD-8610B
External ADSL2+ MODEM
Rev: 1.0.2
1910010011
Download from Www.Somanuals.com. All Manuals Search And Download.
FCC STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
•
Consult the dealer or an experienced radio/ TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions:
1) This device may not cause harmful interference.
2) This device must accept any interference received, including interference
that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
CE Mark Warning
This is a class B product. In a domestic environment, this product may cause radio
interference, in which case the user may be required to take adequate measures.
Download from Www.Somanuals.com. All Manuals Search And Download.
Package Contents
The following contents should be found in your package:
¾
¾
¾
¾
¾
¾
One TD-8610/TD-8610B External ADSL2+ MODEM
One AC power Adapter for TD-8610/TD-8610B External ADSL2+ MODEM
One RJ45 cable
Two RJ11 cable
One ADSL splitter (only available for TD-8610)
One Resource CD for TD-8610/TD-8610B External ADSL2+ MODEM, including:
•
•
This User Guide
Other Helpful Information
Note:
)
Make sure that the package contains the above items. If any of the listed items are
damaged or missing, please contact with your distributor.
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
1.1 Product main specification .............................................................................1
1.2 Supporting protocol ........................................................................................1
1.3 Transmit data-rate..........................................................................................1
1.4 ATM property..................................................................................................2
1.5 System support ..............................................................................................2
1.6 Working environment .....................................................................................2
1.7 Electric parameter ..........................................................................................2
2.1 System requirement .......................................................................................3
2.2 LED explanation.............................................................................................3
2.3 Rear-panel......................................................................................................4
2.4 Hardware installation procedures...................................................................4
Chapter 3. How to use................................................................................6
3.1 Computer Configuration .................................................................................6
3.2 Login...............................................................................................................7
3.3 Setup..............................................................................................................8
3.4 Software Dial..................................................................................................9
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8610/8610B External ADSL MODEM
Chapter 1. Product Overview
With the excellent design of circuit and high quality production, we guarantee ADSL2+ MODEM a
high performance, very good stability and easy to use.
TD-8610/TD-8610B is a complete plug-and-play solution. With standard Ethernet interface, it can
be directly connected to any 10M/100M Ethernet devices, support Auto-MDIX.
TD-8610/TD-8610B not only use html (web mode through Ethernet port) to configure the MODEM
but also use external utility software too. You can download it from our website
1.1 Product main specification
¾
¾
¾
¾
¾
¾
¾
¾
High speed and asymmetry data transmit mode, adapt to wide-band internet access
Point to point connection, provide safe and exclusive bandwidth
Support All ADSL industrial standards
Advanced DMT modulation and demodulation
Firmware upgradeable
Compatible with all mainstream DSLAM (CO)
Real-time Configuration and device monitoring
Quick response semi-conductive surge protect circuit, provides reliable ESD and
surge-protect function
1.2 Supporting protocol
- G.992.1 (G.dmt) - Annex A/B
- G.992.2 (G.lite) - Annex A/B
- ANSI T1.413
- G.992.3 (ADSL2) - Annex A/B compliant
- G.992.5 (ADSL2+) Annex A/B compliant
- ADSL dual latency (fast path and interleaved path)
- I.432 ATM physical layer compliant
-Supports RFC2516 (PPPoE) *
- Supports RFC1483 (EoA) ( Bridged)
Note:
)
“*”Need third-party software.
1.3 Transmit data-rate
¾
Max download data-rate: 24Mbps
1
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8610/8610B External ADSL MODEM
¾
¾
Max upload data-rate: 1Mbps
Max line length: 6Km
1.4 ATM property
¾
¾
AAL0, AAL5, OAM, RM, and raw cell types supported
Direct hardware support for 4 Receive VCs, with additional RX VCs and TX VCs supported in
software
¾
Full 24-bit Virtual Path Identifier (VPI) and Virtual Circuit Identifier (VCI)
1.5 System support
¾
¾
¾
¾
Support PVC
Support IEEE 802.3、IEEE 802.3u
Support 10Base-T/100BASE-TX full-duplex or half duplex Ethernet
Support Auto-MDIX
1.6 Working environment
¾
¾
¾
Operating temperature: 0℃~40 ℃
Storage temperature: -40℃~70 ℃
Humidity: 10%～90%
1.7 Electric parameter
¾
¾
Adaptor power Output: 9VAC/0.8A，50Hz or 60 Hz
Power consumption: 4W Maximum
2
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8610/8610B External ADSL MODEM
Chapter 2. Hardware Installation Guide
2.1 System requirement
Confirm your computer has been installed with networking interface card (NIC) before connecting
ADSL MODEM to your computer, with operating system supporting the TCP/IP protocol.
2.2 LED explanation
The panel of ADSL MODEM includes one power button, one power indicator (RED) and four
function indicators (GREEN), and these five indicators are explained as chart 1-1:
Name
Power
Status
Indication
On
Off
On
Power OK
Power fail
There is data transmitting or receiving on WAN
port
Act
Off
On
Off
No data transmitting or receiving on WAN port
There is a mistake when ADSL is transmitting
data or receiving data
Alarm
ADSL
ADSL normal
Slow flash
Quick flash
On
Self-detecting when power up
The LINE port is sending or receiving ADSL data
The LINE port has connected to ISP’s network
The LINE port is disconnected
Off
On
LAN port is normal
Off
Connection on LAN port is abnormal
Data is transmitting or receiving on LAN port
LAN
Flash
Chart 1-1
3
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8610/8610B External ADSL MODEM
2.3 Rear-panel
¾
¾
ON/OFF: Turn on/off the ADSL modem’s power.
Power (9VAC/0.8A input): please do not use any unknown power adaptor, otherwise that
may cause damage to your ADSL MODEM.
¾
RESET (reset default): When the device is working, please press the reset button of the
Modem, keep the reset button pressed down for more than five seconds and then wait for the
router to reboot.
¾
¾
LAN: Connect with your computer’s NIC.
LINE (WAN): Connect to the MODEM of Splitter or connect to the telephone line.
2.4 Hardware installation procedures
First Step: Connect the MODEM of Splitter with the LINE port of the TD-8610/TD-8610B ADSL2+
MODEM by telephone line. While you need to use a telephone, please attach telephone line into
the phone of Splitter.
Second Step: Connect category 5 cable with RJ45 jacks to ADSL MODEM’s LAN port and your
computer’s NIC.
Third Step: Link power adapter into the power jack of ADSL MODEM. Please note the range of
voltage of power adapter should be within AC 220～230V, 50Hz, which will make the MODEM
under normal operation.
Last Step: Check the line connection to see if everything is ready. Then power up.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8610/8610B External ADSL MODEM
Figure 2-1
5
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8610/8610B External ADSL MODEM
Chapter 3. How to use
3.1 Computer Configuration
1. Connect the cable according to Chapter 2, and then turn on the power.
your PC, enter the IP address as 192.168.1.* (* is any value between 2 to 254, Subnet mask
is 255.255.255.0, Gateway is 192.168.1.1, DNS address is the value provided by ISP).
Figure 3-1
Note:
)
1) The users of Windows 98 can open TCP/IP Properties according to the following:
Right-press (Mouse) Network Neighbor -> Choose Properties -> Double-press TCP/IP. PCI
Fast Ethernet Adapter.
2) The users of Windows 2000/NT/XP can do the following: Right-press Network Neighbor ->
6
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8610/8610B External ADSL MODEM
Choose Properties -> Right-click Local Connection -> Choose Properties -> Double-press
Internet Protocol (TCP/IP).
3) The words in fact maybe are different with this guide.
You can check whether your configuration is successful through PING command. Enter Ping
192.168.1.1
If the screen likes the following, your configuration is successful.
Figure 3-2
If the screen likes the following, your configuration is unsuccessful. Please repeat the previous
steps again.
Figure 3-3
3.2 Login
Startup Internet Explorer, and enter 192.168.1.1; then enter user name (admin), password
information such as link rate.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8610/8610B External ADSL MODEM
Figure 3-4
The default user name and its password is admin; if you want to change it, please go to
Figure 3-5
3.3 Setup
2) Enter the VPI/VCI value which is provided by your ISP, click Save to finish the configuration.
You can press Next to add VPI/VCI value.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
TD-8610/8610B External ADSL MODEM
Figure 3-6
3.4 Software Dial
TD-8610/TD-8610B works in bridged (RFC 1483 Bridged) mode to connect to the Internet. You
need to install dial software on your PC. There is some software working on WINDOWS in market,
example for EnterNet3000, RASPPPoE and WinPeET.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
|
