Sylvania TV VCR Combo SRC21135 User Manual

OWNER’S

MANUAL

13-INCH COLOR TV/VCR

SRC21135

AUDIO

VIDEO

STOP/EJECT

REW

PLAY

F.FWD

REC/OTR

CHANNEL

VOLUME

POWER

This Owner’s Manual is made of

recycled paper.

INSTRUCCIONES EN ESPAÑOL INCLUIDAS.

As an ENERGY STAR^®

Partner, our company has

determined that this product meets

the ENERGY STAR^®guidelines for

If you need additional assistance for set-up or operating

after reading owner’s manual, please call

TOLL FREE : 1-800-968-3429

energy efficiency. ENERGY STAR^®is

a U.S. registered mark.

Download from Www.Somanuals.com. All Manuals Search And Download.

Please read before using this equipment

FIGURE A

EXAMPLE OF ANTENNA GROUNDING AS PER

NATIONAL ELECTRICAL CODE

ANTENNA

LEAD I N

WI RE

GROUND

CL AMP

ANTENNA

DISCHARGE UNIT

(NEC SECTION 810-20)

ELECTRI C

SERVICE

EQUIPMENT

GROUNDING CONDUCTORS

(NEC SECTION 810-21)

GROUND CLAMPS

NEC

NATIONAL ELECTRICAL CODE

POWER SERVICE GROUNDING

ELECTRODE SYSTEM

(NEC ART 250, PART H)

S2898A

13.Outdoor Antenna grounding-If an outside antenna or

cable system is connected to the TV/VCR, be sure the

antenna or cable system is grounded so as to provide some

protection against voltage surges and built-up static

charges. Article 810 of the National Electrical Code,

ANSI/NFPA No. 70, provides information with respect to

proper grounding of the mast and supporting structure,

grounding of the lead-in wire to an antenna discharge unit,

size of grounding conductors, location of antenna-discharge

unit, connection to grounding electrodes, and requirements

for the grounding electrode. (Fig. A)

19.Damage Requiring Service-Unplug this TV/VCR from

the wall outlet and refer servicing to qualified service per-

sonnel under the following conditions:

a. When the power-supply cord or plug is damaged or frayed.

b. If liquid has been spilled, or objects have fallen into the

TV/VCR.

c. If the TV/VCR has been exposed to rain or water.

d. If the TV/VCR does not operate normally by following the

operating instructions. Adjust only those controls that are

covered by the operating instructions, as improper adjust-

ment of other controls may result in damage and will often

require extensive work by a qualified technician to restore

the TV/VCR to its normal operation.

14.Lightning-For added protection for this TV/VCR receiver

during a lightning storm, or when it is left unattended and

unused for long periods of time, unplug it from the wall

outlet and disconnect the antenna or cable system. This will

prevent damage to the TV/VCR due to lightning and

power-line surges.

e. If the TV/VCR has been dropped or damaged in any way.

f. When the TV/VCR exhibits a distinct change in perfor-

mance-this indicates a need for service.

15.Power Lines-An outside antenna system should not be

located in the vicinity of overhead power lines or other

electric light or power circuits, or where it can fall into

such power lines or circuits. When installing an outside

antenna system, extreme care should be taken to keep from

touching such power lines or circuits as contact with them

might be fatal.

20.Replacement Parts-When replacement parts are required,

be sure the service technician has used replacement parts

specified by the manufacturer that have the same character-

istics as the original part. Unauthorized substitutions may

result in fire, electric shock, injury to persons or other haz-

ards.

21.Safety Check-Upon completion of any service or repairs to

this TV/VCR, ask the service technician to perform routine

safety checks to determine that the TV/VCR is in proper

operating condition.

16.Overloading-Do not overload wall outlets and extension

cords as this can result in a risk of fire or electric shock.

17.Object and Liquid Entry-Never push objects of any kind

into this TV/VCR through openings as they may touch dan-

gerous voltage points or short out parts that could result in

a fire or electric shock. Never spill liquid of any kind on

the TV/VCR.

22.Heat-This TV/VCR product should be situated away from

heat sources such as radiators, heat registers, stoves, or

other products (including amplifiers) that produce heat.

18.Servicing-Do not attempt to service this TV/VCR yourself

as opening or removing covers may expose you to danger-

ous voltage or other hazards. Refer all servicing to quali-

fied service personnel.

CAUTION:TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY

INSERT.

ATTENTION: POUR ÉVITER LES CHOC ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE

LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.

_{Download from Www.Somanuals}-_.c3_om-_{. All Manuals Search And Download.}

9I03

PRECAUTIONS

IMPORTANT COPYRIGHT INFORMATION

LOCATION

For safe operation and satisfactory performance of

your TV/VCR, keep the following in mind when

selecting a place for its installation:

Shield it from direct sunlight and keep it away

from sources of intense heat.

Avoid dusty or humid places.

Avoid places with insufficient ventilation for proper

heat dissipation. Do not block the ventilation holes

at the top and bottom of the unit. Do not place the

unit on a carpet because this will block the ventila-

tion holes.

Unauthorized recording or use of broadcast televi-

sion programming, video tape, film or other copy-

righted material may violate applicable copyright

laws. We assume no responsibility for the unautho-

rized duplication, use, or other acts which infringe

upon the rights of copyright owners.

•

FCC WARNING- This equipment may gener-

ate or use radio frequency energy. Changes or

modifications to this equipment may cause

harmful interference unless the modifications

are expressly approved in the instruction man-

ual. The user could lose the authority to oper-

ate this equipment if an unauthorized change

or modification is made.

Install unit in a horizontal position.

Avoid locations subject to strong vibration.

Do not place the TV/VCR near strong magnetic fields.

Avoid moving TV/VCR to locations where temper-

•

ature differences are extreme.

This equipment has been tested and found to com-

ply with the limits for a Class B digital device, pur-

suant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against

harmful interference in a residential installation.

This equipment generates, uses, and can radiate

radio frequency energy and, if not installed and

used in accordance with the instructions, may cause

harmful interference to radio communications.

However, there is no guarantee that interference

will not occur in a particular installation. If this

equipment does cause harmful interference to

radio or television reception, which can be deter-

mined by turning the equipment off and on, the

user is encouraged to try to correct the interfer-

ence by one or more of the following measures:

1) Reorient or relocate the receiving antenna.

2) Increase the separation between the equipment

and receiver.

AVOID THE HAZARDS OF

ELECTRICAL SHOCK AND FIRE

•

Do not handle the power cord with wet hands.

Do not pull on the power cord when disconnecting

it from an AC wall outlet. Grasp it by the plug.

If, by accident, water is spilled on your unit, unplug

the power cord immediately and take the unit to an

Authorized Service Center for servicing.

Do not put your fingers or objects into the

TV/VCR cassette holder.

Do not place anything directly on top of the unit.

•

WARNING

Moisture condensation may occur inside the unit

when it is moved from a cold place to a warm place,

or after heating a cold room or under conditions of

high humidity. If a tape is played in a TV/VCR

which has moisture, it may damage the tape and

TV/VCR. Therefore if condensation occurs inside the

unit, turn the POWER button on and allow at least 2

hours for the unit to dry out.

3) Connect the equipment to an outlet on a circuit

different from that to which the receiver is con-

nected.

4) Consult the dealer or an experienced radio/TV

technician for help.

The serial number of this product may be found on the back of the unit. No other TV/VCR has the same serial

number as yours. You should record the number and other vital information here and retain this book as a per-

manent record of your purchase to aid identification in case of theft. Serial numbers are not kept on file.

Date of Purchase

Dealer Purchase from

Dealer Address

Dealer Phone No.

Model No.

Serial No.

_{Download from Www.Somanuals}-_.c4_om-_{. All Manuals Search And Download.}

9I03

TABLE OF CONTENTS

C IMPORTANT SAFEGUARDS . . . . . . . . . . . . .2

C PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . .4

C FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

C SUPPLIED ACCESSORIES . . . . . . . . . . . . . . .6

C OPERATING CONTROLS AND FUNCTIONS 7

C RECORDING . . . . . . . . . . . . . . . . . . . . . . . . .20

NORMAL RECORDING . . . . . . . . . . . . . . . . .20

OTR (One Touch Recording) . . . . . . . . . . . . . .21

TIMER RECORDING . . . . . . . . . . . . . . . . . . .21

TIMER PROGRAM EXTENSION . . . . . . . . .22

HINTS FOR AUTOMATIC TIMER

RECORDING . . . . . . . . . . . . . . . . . . . . . . . . .23

C PREPARATION FOR USE . . . . . . . . . . . . . . . .9

ANTENNA/CABLE CONNECTIONS . . . . . . .9

MOBILE CONNECTION . . . . . . . . . . . . . . . .10

EXTERNAL INPUT MODE . . . . . . . . . . . . . .10

INSTALLING THE BATTERIES . . . . . . . . . . .10

AUTO RETURN . . . . . . . . . . . . . . . . . . . . . . .23

WAKE UP TIMER . . . . . . . . . . . . . . . . . . . . . .23

SLEEP TIMER . . . . . . . . . . . . . . . . . . . . . . . . .24

C COPYING A VIDEO TAPE . . . . . . . . . . . . . . .24

C ON SCREEN DISPLAY . . . . . . . . . . . . . . . . .25

C SET UP FOR USE . . . . . . . . . . . . . . . . . . . . . .11

CHANNEL SET UP FOR THE FIRST TIME . .11

CLOCK SET UP (AUTO / MANUAL) . . . . . .11

CHANNEL SET UP AGAIN . . . . . . . . . . . . . .13

DELETING (OR ADDING) CHANNEL . . . . .13

SELECTING THE LANGUAGE . . . . . . . . . . .13

DAYLIGHT-SAVING TIME . . . . . . . . . . . . . .14

C SPECIAL FEATURES . . . . . . . . . . . . . . . . . .25

REAL TIME TAPE COUNTER . . . . . . . . . . . .25

AUTO REWIND-EJECT . . . . . . . . . . . . . . . . .25

C MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . .25

C TROUBLESHOOTING GUIDE . . . . . . . . . . .26

C SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . .27

C CABLE CHANNEL DESIGNATIONS . . . . . .27

C WARRANTY . . . . . . . . . . . . . . . . . . .Back Cover

C TV OPERATION . . . . . . . . . . . . . . . . . . . . . . .14

WATCHING A TV PROGRAM . . . . . . . . . . . .14

GAME MODE . . . . . . . . . . . . . . . . . . . . . . . . .14

DEGAUSSING . . . . . . . . . . . . . . . . . . . . . . . .15

PICTURE CONTROL . . . . . . . . . . . . . . . . . . .15

CLOSED CAPTION SYSTEM . . . . . . . . . . . .15

V-CHIP SET UP . . . . . . . . . . . . . . . . . . . . . . . .16

C PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . . . . .17

NORMAL PLAYBACK . . . . . . . . . . . . . . . . . .17

AUTO REPEAT PLAYBACK . . . . . . . . . . . . .18

SEARCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

SLOW MOTION . . . . . . . . . . . . . . . . . . . . . . .19

RENTAL PLAYBACK . . . . . . . . . . . . . . . . . . .19

VERTICAL HOLD CONTROL . . . . . . . . . . . .20

STILL PICTURE . . . . . . . . . . . . . . . . . . . . . . .20

TRACKING ADJUSTMENT . . . . . . . . . . . . . .20

A NOTE ABOUT RECYCLING

This product’s packaging materials are recyclable and can be reused. Please dispose of any materials in

accordance with your local recycling regulations.

Batteries should never be thrown away or incinerated but disposed of in accordance with your local regula-

tions concerning chemical wastes.

_{Download from Www.Somanuals}-_.c5_om-_{. All Manuals Search And Download.}

9I03

FEATURES

Rotary 4-head Record/Playback System–Four

heads ensure excellent picture quality and special

effects playback.

Index Search–Fast-forwards to start of next recording.

Slow Motion–View recorded program at slower

than normal speed.

Infrared remote control

Bilingual on screen menu display selectable in

English or Spanish

Auto Head Cleaner–Automatically cleans video

•

heads as you insert or remove a cassette.

Zero Return–The tape returns to counter of

0:00:00 by rewinding or fast forwarding.

Still–“Freeze” the picture at any time, for close

viewing of a particular scene. Only tapes recorded

in SLP mode will show a fairly clear picture.

Digital Auto Tracking (DTR)–Automatically

adjusts the tracking for each tape you play.

Rental play mode–Improves playback picture

quality from worn tapes, such as rental tapes.

Auto repeat–Allows you to repeat the playing of a

tape indefinitely without pressing the PLAY button.

Time search–Lets you set the TV/VCR to advance

the tape by entering the desired playback time you

want to skip.

•

Real time counter–This shows the elapsed record-

ing or playback time in hours, minutes, and sec-

onds. The “–” indication will appear when the tape

is rewound further than the tape counter position

“0:00:00”.

181 channel capability PLL frequency synthesiz-

er tuner with direct station call–(A converter may

be necessary to view scrambled cable channels.)

Auto Clock Setting–Allows you to set the clock

from a PBS broadcast station.

Closed caption system–You may view specially

labeled (cc) TV programs, movies, news, prere-

corded tapes, etc. with either a dialogue caption or

text display added to the program.

Game mode–Automatically sets external input

mode and allows the TV/VCR display to be suit-

able for use with TV games.

Auto power on and off system–Automatically

turns on the TV/VCR when you insert the cassette,

turns off after auto-rewind, and ejects when the

beginning of the tape is reached.

Auto rewind when the end of a tape is

reached–This function doesn’t occur when using

timer recording.

2 Step picture search operation–You can view a

video program at a high speed or super high speed

in either a forward or reverse direction in LP and

SLP mode. For SP mode only high speed.

Three different playback tape speeds : SP/LP/SLP

Two different recording tape speeds : SP/SLP

•

OTR (One Touch Recording)–Instant timed

recording from 30 to 480 minutes is possible at the

push of the REC/OTR button.

•

1 Year, 8 events (including Daily and Weekly

Timer Recording)–The built-in timer allows you to

record up to 8 programs at different times on dif-

ferent channels up to 1 year in advance. The Daily

timer allows recordings to be made of daily broad-

casts, and the Weekly timer allows recording to be

made once a week up to the end of the tape.

Auto return–After timer recording is finished, the

TV/VCR can return to the beginning of the record-

ing.

Wake-up/Sleep timer–Allows you to have the

TV/VCR automatically turn on or off at a desired

time.

Timer Program Extension–Allow you to shift the

time schedule for automatic timer recording.

V-CHIP–Enables parents to prevent their children

from watching inappropriate material on TV.

Two- way power–Allows you to power the

TV/VCR with standard household AC or your vehi-

cle’s battery, using the supplied car-battery cord.

•

SUPPLIED ACCESSORIES

AC Cord

2 AA

Batteries

Remote Control Unit

Rod Antenna

Car Battery Cord

PART NO

(N0145UD or

N0157UD)

(0EMN00673 or

0EMN01599 or

0EMN01755)

(WPV0182LW001 or

WPV0182HHH01)

(WPC0192HD002)

If you need to replace these accessories, please refer to the PART NO. under the illustrations and call 1-800-

968-3429.

Depending on your antenna system, you may need different types of Combiners (Mixer) or Separators

(Splitter). Contact your local electronics store for these items.

We do not recommend the use of universal remote controls. Not all of the functions may be controlled with

a universal remote control. If you decide to use a universal remote control with this unit, please be aware

that the code number given may not operate this unit. In this case, please call the manufacturer of the uni-

versal remote control.

•

_{Download from Www.Somanuals}-_.c6_om-_{. All Manuals Search And Download.}

9I03

OPERATING CONTROLS AND FUNCTIONS

- TV/VCR FRONT PANEL -

AUDIO

VIDEO

STOP/EJECT

REW

PLAY F.FWD

REC/OTR

CHANNEL

VOLUME

POWER

8 9 10

12 13

- REMOTE CONTROL -

L button–

Press to select setting modes from the on screen

menu.

Press to enter digits when setting program.

(for example: setting clock or timer program)

•

WAKE-UP

/SLEEP

POWER

EJECT

CHANNEL

RETURN

4 EJECT button [Remote control]– Press in the

Stop mode to remove tape from TV/VCR.

5 REW button– Press to rewind the tape, or to view

the picture rapidly in reverse during playback

mode. (Rewind Search)

CHANNEL

VOLUME

+100

s button–

DISPLAY

MUTE

Press to select a mode from a particular menu.

•

(for example: LANGUAGE or USER’S SET UP)

6 PLAY button– Press to begin playback.

K button–

PLAY

REW

F.FWD

STOP

RECORD

SPEED PAUSE/STILL

Press to select setting modes from the on

screen menu.

Press to enter digits when setting program.

•

T-PROG.

CLEAR

GAME

SLOW

COUNTER

RESET

•

(for example: setting clock or timer program)

7 F.FWD button– Press to rapidly advance the tape,

or to view the picture rapidly in forward during

playback mode. (Forward Search)

B button–

1 EARPHONE jack– Connects to earphones (not

supplied) for personal listening. The size of jack is

1/8” monaural (3.5mm).

2 AUDIO input jack– Connect to the audio output

jack of your audio equipment, video camera or

another VCR.

When setting program (for example: setting clock

or timer program), press to determine your selec-

tion and proceed to the next step you want to input.

Press to determine setting modes from on screen

menu.

•

3 VIDEO input jack– Connect to the video output

jack of your video camera or another VCR.

4 STOP button [TV/VCR ]– Press to stop the tape

motion.

Press to select a mode from a particular menu.

(for example: LANGUAGE or USER’S SET UP)

•

EJECT button [TV/VCR ]– Press in the Stop mode

to remove tape from TV/VCR.

_{Download from Www.Somanuals}-_.c7_om-_{. All Manuals Search And Download.}

9I03

- REAR VIEW -*

DC 13.2V

AC 120V

ANT.

27 28

8 REC button– Press for manual recording.

OTR button– Activates One Touch Recording.

(only on the TV/VCR)

9 RECORD indicator– Flashes during recording.

Lights up in the Stand-by mode for Timer Recording.

10 Remote Sensor Window– Receives the infrared

signals from the remote control.

11 CHANNEL K / L buttons– Press to select the

desired channels for viewing or recording, listening

of FM radio.

18 SPEED button– Press to choose the desired

recording speed:SP/SLP.

19 T-PROG. CLEAR button– Press to cancel a setting

of timer program. (See page 23.)

COUNTER RESET button– Press to reset counter

to 0:00:00.

20 GAME button– Sets the game mode and external

input mode at the same time. (See page 14.)

21 SLOW button– Press to start slow motion playback.

The slow speed can be controlled by pressing the

F.FWD button (faster) or the REW button (slower).

(only on the remote control).

22 PAUSE/STILL button– Press to temporarily stop

the tape during the recording or to view a still pic-

ture during playback.

You may display the main menu on the TV screen

by pressing repeatedly this button on the TV/VCR.

TRACKING function– Press to minimize video

‘noise’ (lines or dots on screen) during playback

or Slow mode. (See page 20.)

Frame Advance function– Press to advance the

picture one frame at a time during Still mode.

23 MUTE button– Mutes the sound. Press it again to

resume sound.

12 VOLUME X / Y buttons– Adjust the volume level.

13 POWER button– Press to turn TV/VCR on and

off. Press to activate timer recording.

14 Cassette compartment

24 CHANNEL RETURN button– Press to go back to

the previously viewed channel. For example,

pressing this button once will change channel dis-

play from 3 (present channel) to 10 (previously

viewed channel), and pressing it a second time

will return from 10 to 3.

25 WAKE UP/SLEEP button– Sets the Wake up or

Sleep Timer. (See page 23 and 24.)

26 ANT. terminal– Connect to an antenna or cable

system.

15 Number buttons– Press to select desired channels

for viewing or recording. To select channels from

1 to 9, first press the 0 button and then 1 to 9.

+100 button– When selecting cable channels which

are higher than 99, press this button first, then press

the last two digits. (To select channel 125, first press

the “+100” button then press “2” and “5”).

16 MENU button– Press to display the main menu on

the TV screen.

17 DISPLAY button– Display the counter or the cur-

rent channel number and current time on the TV

screen. (See page 25.)

27 DC 13.2V jack– Connect to the Car Battery Cord.

28 AC 120V jack– Connect to the AC cord.

_{Download from Www.Somanuals}-_.c8_om-_{. All Manuals Search And Download.}

9I03

PREPARATION FOR USE

ANTENNA/CABLE CONNECTIONS

From Cable System or

Satellite Dish

VHF/UHF Antenna

(Not supplied)

Rod Antenna

(Supplied)

Satellite Box or

Cable Box

OUT

(Not supplied)

VHF Antenna

(Not supplied)

UHF Antenna

(Not supplied)

From

Cable System

DC 13.2V

AC 120V

ANT.

VHF/UHF

Combiner

(Not supplied)

ANT.

75-ohm Coaxial

Cable (Not supplied)

Flat twin-lead cable

VHF/UHF COMBINED ANTENNA

VHF/UHF SEPARATE ANTENNAS

The VHF/UHF Rod Antenna (supplied) is detach-

able. Insert the stem of the antenna into the hole on

the upper-back portion of the TV/VCR.Connect the

VHF/UHF Rod Antenna or VHF/UHF Combination

Antenna to the ANT. terminal of the TV/VCR as

shown in the diagram. For the best reception, fully

extend the VHF/UHF Rod Antenna and make the

necessary adjustments. (Avoid touching the top sec-

tion when adjusting.)

In some areas it will be necessary to use an outdoor

antenna.

CABLE WITHOUT CONVERTER/

DESCRAMBLER BOX

Use this connection if your cable system connects

directly to your TV/VCR without a converter box.

By using this connection you can:

1) Use the TV/VCR remote to select channels.

2) Program one or more unscrambled channels for

Automatic Timer Recording.

NOTE: This unit will ONLY record and view the

same channel.

NOTE:

Before plugging the Rod antenna into antenna termi-

nal, check that the pin is not bent. If it is bent,

straighten the pin as illustrated, then plug the pin into

antenna terminal.

CABLE WITH CONVERTER/

DESCRAMBLER BOX OR SATELLITE

BOX

Bent pin

If your cable service supplies you with a converter

box or if you use a satellite system, you can use the

basic connection shown in the diagram.

Cable Plug

(Straight pin)

(Needs to be straightened)

By using this connection you can also record scram-

bled channels. However, channel selection must be

made with the converter box or satellite box. This

means that channels cannot be changed using the

TV/VCR Remote Control. Unattended timer record-

ing is limited to one channel at a time.

NOTE:

The connection of an indoor antenna may not always

give acceptable TV reception.

Note to CATV system installer:

This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that

provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connect-

ed to the grounding system of the building as close to the point of cable entry as practical.

_{Download from Www.Somanuals}-_.c9_om-_{. All Manuals Search And Download.}

9I03

TO RECORD A SCRAMBLED/UNSCRAMBLED

CHANNEL

EXTERNAL INPUT MODE

1) Set the TV/VCR channel selector to the output

channel of the Cable Converter Box or Satellite

Box. (Example: CH3)

When using an external input signal (another VCR or

video camera), connect the player’s audio/video out-

put cables to the AUDIO IN/ VIDEO IN jacks of

2) Select the channel to record from your Cable

Converter Box or Satellite Box.

AUX

MOBILE CONNECTION

WARNING:The driver should never watch

the TV/VCR while operating a motor vehicle.

INSTALLING THE BATTERIES

CAUTION: If you use the TV/VCR with the

vehicle’s engine off, recharge the vehicle’s

battery after every 4 hours of use to prevent

it from running down. After you finish using

the TV/VCR be sure you unplug the car-bat-

tery cord from the cigarette-lighter socket.

1)Open the battery compartment cover by pressing

the cover on the remote unit in the direction of the

arrow.

2)Insert 2 “AA” penlight batteries into the battery

compartment in the direction indicated by the

polarity (+/-) markings.

1) The supplied indoor antenna is adequate when

your vehicle is stationary. For best reception on

the road, use a high-quality VHF/UHF mobile TV

antenna.

3)Replace the cover.

2) Attach the car battery cord to the DC13.2V (12V)

connector on the back of the TV/VCR. Then, con-

nect the other end to your vehicle’s cigarette-

lighter socket.

NOTES:

Be sure your vehicle has a 13.2-volt (12-volt), neg-

ative-ground electrical system.

•

Be sure you use only the supplied car battery cord.

Using another cord could damage the TV/VCR.

•

Be sure the socket is free of ashes and other debris.

Be sure to push the car battery cord’s plug com-

pletely into the cigarette-lighter socket.

•

Always unplug the car battery from the cigarette-

lighter socket before you unplug it from the

TV/VCR.

•

You must disconnect the car battery cord from the

TV/VCR before you can use the AC power.

•

Be sure to replace the fuse with only the same

type, 5A, 250V.

•

To the vehicle's

cigarette-lighter socket

VHF/UHF Combination

Mobile Antenna

(Not supplied)

Car battery cord

(Supplied)

DC 13.2V

AC 120V

DC13.2V

ANT.

- 10 -

9I03

Download from Www.Somanuals.com. All Manuals Search And Download.

SET UP FOR USE

You can program the tuner to scan all the channels

TO SELECT A DESIRED CHANNEL

You can select the desired channel by using the

CHANNEL K or L button or directly pressing the

number buttons on the remote control.

you receive in your area.

NOTE: Channel memory programming is NOT

needed when connected to a cable box or satellite

box. Just select the TV/VCR channel selector to the

output channel of the cable box or satellite box (Ex

CH3). Then select the channel to be viewed on the

Cable Box or Satellite Box.

Note for using the number buttons:

When selecting cable channels which are higher

•

than 99, press the +100 button first, then, press the

last two digts. (Example: to select channel 125,

first press the +100 button then press “2” and “5”).

CHANNEL SET UP FOR THE

FIRST TIME

You must proceed single-digit channel numbers

with a zero (Example: 02 ... 09).

•

1 Plug in the TV/VCR

power cord

(Rear)

Plug the TV/VCR power

AC 120V

CLOCK SET UP

(AUTO / MANUAL)

Set the clock accurately for proper automatic timer

recording. If the Public Broadcasting Station (PBS)

is available in your area, follow “AUTO CLOCK

SETTING”. If it is not, follow “MANUAL CLOCK

SETTING”.

cord into a standard AC

outlet.

NOTE:

If some digits appear

in the corner of the screen, press the POWER but-

ton without unplugging the power cord.

•

2 Turn on the TV/VCR

AUTO CLOCK SETTING

Press the POWER button to turn on the TV/VCR

You can have the TV/VCR set the clock automatical-

ly by using the Public Broadcasting Station (PBS)

channel in your area. Once you have set the clock by

using the following procedure, the TV/VCR will

automatically monitor the correct time and date

being broadcast by the PBS station in your area,

using a new service called Extended Data Service

(XDS).

3 Select “ENGLISH” or “ESPAÑOL”

– SET UP –

Select “ENGLISH” or

LANGUAGE

“ESPAÑOL”=Spanish using the

F.FWD/B or REW/s button. “[ ]”

indicate the selected language.

[ENGLISH] ESPAÑOL

AUTO PRESET

Make sure ...

TV/VCR power must be turned on.

Confirm that the antenna connections are correct.

The cable converter box must be turned on if your

TV/VCR is connected directly to it. (See NOTES:)

•

4 Begin auto preset

– SET UP –

•

Press the PLAY/K or STOP/L but-

ton to point to “AUTO PRESET”.

Then press the F.FWD/B button.

The tuner scans and memorizes all

active channels in your area.

LANGUAGE

[ENGLISH] ESPAÑOL

•

AUTO PRESET

The channel is properly set in advance.

•

NOTES:

The TV/VCR distinguishes between standard TV

channels and cable channels.

•

Auto clock setting only needs to be set once. But it

can be done again if the clock’s time has become

incorrect for some reason.

•

If you want to play or record a video tape

BEFORE presetting the tuner, you must press the

MENU button on the remote control. To preset the

tuner again, see “CHANNEL SET UP AGAIN” on

page 12.

•

If the TV/VCR is connected directly to a cable

•

converter box or satellite box, the local PBS station

must be selected on the cable box itself, and the

TV/VCR must be set to the output channel of the

cable converter box or satellite box (usually chan-

nel 3 or 4), to be able to set up or correct the clock

automatically.

The TV/VCR may memorize TV channels as

CATV channels if reception conditions are poor. If

this happens, try the AUTO MEMO action again

when reception conditions are better.

•

If you do not know what your local PBS station is,

then follow “Manual Clock Settings”.

5 After scanning

The TV/VCR cannot control the channels of the

cable converter box or satellite box.

If tou use a mobile connection, you cannot set the

AUTO CLOCK and D.S.T functions.

The tuner stops on the lowest memorized channel.

If you want to recall the selected channels, you can

select the desired channel directly with the remote

control number buttons or CHANNEL K or Lbutton.

•

- 11 -

8H30

Download from Www.Somanuals.com. All Manuals Search And Download.

– M E N U –

1 Select “SETTING CLOCK”

Press the MENU button on the

remote control.

Press the PLAY/K or STOP/L but-

ton to point to “SETTING

CLOCK”.

1 Select “SETTING CLOCK”

Press the MENU button on the

remote control. Press the PLAY/K

or STOP/L button to point to “SET-

TING CLOCK”.

TIMER PROGRAMMING

PICTURE CONTROL

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

TIMER PROGRAMMING

PICTURE CONTROL

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

INDEX SEARCH

Then, press the F.FWD/B button.

– SETTING CLOCK –

2 Select “MANUAL CLOCK

– SETTING CLOCK –

AUTO CLOCK

[ON]

2 Set “AUTO CLOCK” to [ON]

Press the F.FWD/B or REW/s

button repeatedly until [ON]

appears.

SET”

AUTO CLOCK CH

[AUTO]

[OFF]

AUTO CLOCK

[ON]

Press the PLAY/K or STOP/L but-

ton to point to “MANUAL CLOCK

SET”.

AUTO CLOCK CH

[AUTO]

[OFF]

MANUAL CLOCK SET

D.S.T.

MANUAL CLOCK SET

D.S.T.

Then, press the F.FWD/B button.

3 Enter the channel number for

the PBS station

– SETTING CLOCK –

– MANUAL CLOCK SET –

MONTH DAY YEAR

3 Select the month

AUTO CLOCK

[ON]

AUTO CLOCK CH

[AUTO]

Press the PLAY/K or STOP/L but-

ton until your desired month

appears. (Example: May → 05)

Then, press the F.FWD/B button.

Press the PLAY/K or STOP/L but-

ton to point to “AUTO CLOCK

CH”.

Then press the F.FWD/B or REW/s button until the

channel number for your local PBS station appears.

If you do not know the PBS channel number, leave it

set to [AUTO] which is located before [2]. The

TV/VCR will search automatically all available chan-

nels for the local PBS station, and will select that

channel.

0 5

– – – – – – – – –

MANUAL CLOCK SET

D.S.T.

HOUR

MINUTE

[OFF]

– –

– – – –

– MANUAL CLOCK SET –

MONTH DAY YEAR

4 Select the day

Press the PLAY/K or STOP/L but-

ton until your desired day appears.

(Example: 1st → 01)

0 5

0 1 – – – – – – –

HOUR

MINUTE

– –

– – – –

Then, press the F.FWD/B button.

4 Exit the Auto Clock Setting

Press the MENU button on the remote control to

return to TV mode.

– MANUAL CLOCK SET –

MONTH DAY YEAR

5 Select the year

Press the PLAY/K or STOP/L but-

ton until your desired year appears.

(Example: 2001)

0 5

0 1 TUE 2 0 0 1

HOUR

MINUTE

– –

– – – –

Then, press the F.FWD/B button.

5 Turn off the TV/VCR

Turn the TV/VCR off. The Auto Clock functions

automatically while the TV/VCR is off.

– MANUAL CLOCK SET –

MONTH DAY YEAR

6 Select the hour

Press the PLAY/K or STOP/L but-

ton until your desired hour appears.

(Example: 5, PM)

If you choose [AUTO],

0 5

0 1 TUE 2 0 0 1

The TV/VCR must search until the PBS channel is

•

HOUR

0 5

MINUTE

– – PM

found. It must scan each channel for a couple of

seconds to determine if that channel is transmitting

the XDS signal.

Then, press the F.FWD/B button.

– MANUAL CLOCK SET –

MONTH DAY YEAR

7 Select the minute

If the time that is automatically set by this selected

•

Press the PLAY/K or STOP/L but-

ton until the desired minute appears.

(Example: 40)

PBS station is incorrect, it may not be your local

PBS station, but one from a different time zone.

Or if no channel is broadcasting the XDS signal in

your area, no time will show. In these cases, you

must manually enter the correct local PBS station,

or set the clock manually and turn off the Auto

Clock Setting feature.

0 5

0 1 TUE 2 0 0 1

HOUR

0 5

MINUTE

4 0 PM

5:40 PM

8 Start the clock

Press the MENU button on the

remote control.

MANUAL CLOCK SETTING

Although seconds are not displayed,

they begin counting from 00 when

you press the MENU button on the remote control.

Use this feature to synchronize the clock with the

correct time.

Make sure ...

TV/VCR power must be turned on.

In the example below, the clock is to be set to:

•

DATE

May 1st, 2001

SETTING TIME 5:40PM

- 12 -

8H30

Download from Www.Somanuals.com. All Manuals Search And Download.

NOTE:

When unplugging the AC cord or if there is a power

failure for more than 30 seconds, you may have to

reset the clock.

1 Select “CHANNEL SET UP”

Press the MENU button on the

remote control.

Press the PLAY/K or STOP/L but-

ton to point to “CHANNEL SET

UP”.

– M E N U –

TIMER PROGRAMMING

PICTURE CONTROL

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

TO CHANGE CLOCK SETTING

If you want to change the clock,

1)Follow steps [1] and [2].

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

INDEX SEARCH

Then, press the F.FWD/B button.

2)Select where you want to change using the

F.FWD/B or REW/s button.

3)Enter correct numbers using the PLAY/K or

STOP/L button.

4)Press the MENU button on the remote control to

start the clock.

– CHANNEL SET UP –

2 Select “ADD/DELETE CH”

Press the PLAY/K or STOP/L but-

ton to point to “ADD/DELETE

CH”.

ADD / DELETE CH (TV)

AUTO PRESET

Press the F.FWD/B button.

PLEASE NOTE:

If there is no local PBS station in your area or on

your cable system, select “AUTO CLOCK” and press Press the PLAY/K or STOP/L but-

3 Enter the desired channel number

the F.FWD/B or REW/s button to turn [OFF] this

function. Then you can manually adjust the clock.

ton until your desired channel num-

ber appears. (You can also use the

number buttons or the CHANNEL

K/L button to enter it.) (Example:

CH8)

ADD / DELETE

CHANNEL SET UP AGAIN

Make sure ...

4 Delete (or add) it from (into) memory

Press the POWER button to turn on the TV/VCR.

•

Press the F.FWD/B or REW/s button. The channel

number changes to light red. The channel is deleted

from memory.

•

1 Select “CHANNEL SET UP”

Press the MENU button on the

remote control.

Press the PLAY/K or STOP/L but-

ton to point to “CHANNEL SET

UP”.

– M E N U –

TIMER PROGRAMMING

PICTURE CONTROL

To delete another channel, repeat steps [3] and [4].

If you press the F.FWD/B or REW/s button

again, the channel is memorized again.

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

INDEX SEARCH

Added channel: Light blue.

Deleted channel: Light red.

Then, press the F.FWD/B button.

2 Begin auto preset

– CHANNEL SET UP –

5 Exit the channel setup mode

ADD / DELETE CH (TV)

AUTO PRESET

Press the PLAY/K or STOP/L but-

ton to point to “AUTO PRESET”.

Then, press the F.FWD/B button.

The tuner scans and memorizes all

the active channels in your area.

Press the MENU button on the remote control to

returns to TV mode.

NOTE: To confirm that channel(s) has been deleted

or added, press the CHANNEL K or L button.

SELECTING THE LANGUAGE

Make sure ...

Press the POWER button to turn on the TV/VCR.

NOTE: This function effects only the language on

3 After scanning

The tuner stops on the lowest memorized channel.

•

the screen menu and not the audio source.

DELETING (OR ADDING)

CHANNEL

The channels you no longer receive or seldom watch

can be deleted from the memory. (Of course, you

can add the deleted channel into the memory again.)

– M E N U –

1 Select “LANGUAGE”

TIMER PROGRAMMING

PICTURE CONTROL

SETTING CLOCK

Press the MENU button on the

remote control.

Press the PLAY/K or STOP/L but-

ton to point to “LANGUAGE”.

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

INDEX SEARCH

- 13 -

8H30

Download from Www.Somanuals.com. All Manuals Search And Download.

– M E N U –

2 Select “ENGLISH” or “ESPAÑOL”

Select “ENGLISH” or “ESPAÑOL”= Spanish using

the F.FWD/B or REW/s button.

1 Select “SETTING CLOCK”

Press the MENU button on the

remote control.

Press the PLAY/K or STOP/L

button to point to “SETTING

CLOCK”.

TIMER PROGRAMMING

PICTURE CONTROL

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

INDEX SEARCH

3 Exit the Language mode

Press the MENU button on the remote control to

return to TV mode.

Then, press the F.FWD/B button.

NOTE: If for some reason the menu is in Spanish,

press the MENU button on the remote control, press

the PLAY/K button to point to “IDIOMA

[ESPAÑOL]”, then press the F.FWD/B button, then

press the MENU button on the remote control.

2 Set “D.S.T.” (Daylight-Saving Time) to [ON]

Press the PLAY/K or STOP/L

– SETTING CLOCK –

button to point to “D.S.T.”.

AUTO CLOCK

[ON]

AUTO CLOCK CH

[AUTO]

Then, press the F.FWD/B or

REW/s button until [ON]

appears.

MANUAL CLOCK SET

D.S.T.

[ON]

DAYLIGHT-SAVING TIME

Select this feature and the TV/VCR’s clock automati-

cally will advance one hour in April, then reverse one

hour in October.

When Daylight-Saving Time is ON, the clock will

change automatically as follows:

3 Exit the Daylight-Saving Time mode

Press the MENU button on the remote control to

return to TV mode.

NOTE: If tou use a mobile connection, you cannot

set the AUTO CLOCK and D.S.T functions.

First Sunday of April : At 2 AM the clock imme-

•

diately changes to 3 AM. Any timer programming

you have set to occur between 2 AM and 3 AM

will not record.

Last Sunday of October : At 2 AM the clock

immediately changes to 1 AM.

Make sure ...

Press the POWER button to turn on the TV/VCR.

TO CANCEL THE DAYLIGHT-SAVING

TIME

Repeat steps [1] to [2], select [OFF] using the

F.FWD/B or REW/s button.Then, press the

MENU button on the remote control to return to

TV mode.

•

TV OPERATION

WATCHING A TV PROGRAM

GAME MODE

This function enables you to decrease the TV screen

contrast and making it suitable for use with a TV

GAME.

1 Turn on the TV/VCR

Press the POWER button to turn on the TV/VCR.

NOTE: This function can not be set during recording.

2 Select the channel number

Press the CHANNEL K or L button to select your

desired channel number or press the number buttons

on the remote control.

Press the GAME button on the

remote control. “GAME” appears

on the screen.

GAME

Remember: If the TV/VCR is connected to a cable

box or satellite box, the TV/VCR must be on CH3 or

CH4, then the channel to be viewed must be selected

on the cable box or satellite box.

When you press the GAME button;

The TV/VCR comes on automatically if it is off.

The TV/VCR will be in external input mode auto-

•

matically.

3 Adjust sound

Press the VOLUME X or Y button

to adjust the volume.

TO CANCEL THE GAME MODE

Press the GAME button or CHANNEL K or L but-

ton on the remote control.

VOLUME 20

- 14 -

8H30

Download from Www.Somanuals.com. All Manuals Search And Download.

DEGAUSSING

Magnetism from nearby appliances might affect the

color of the TV picture.

If this happens, move this unit away from the appli-

ance. If the color is still not correct, disconnect

power cord from AC outlet then reconnect it after 30

minutes.

CLOSED CAPTION SYSTEM

You can view specially labeled (cc) TV programs,

movies, news, pre-recorded tapes with either a dia-

logue caption or text display.

CAPTION mode: By choosing the caption mode, you

can watch dramas, movies and news while captioning

the dialogues and the contents of news.

TEXT mode: By choosing the text mode, you can

watch half screen text information if you want.

1-2: You may get these captions or text information

by selecting either “1” or “2”. Caption “2” is usually

used for a second language if available.

PICTURE CONTROL

The TV/VCR’s picture controls – BRIGHT, CON-

TRAST, COLOR, TINT and SHARPNESS – are

preset to factory specifications. Although they are

usually the best, you may need to make some further

adjustments for a natural looking image.

NOTES:

Procedures must be followed within 5 seconds or

the Picture Control mode will be cancelled.

When setting the Picture Control, the Game mode

will be cancelled.

NOTE:

Not all programs are broadcast with closed captions.

Your television is designed to provide error free

closed captions from high quality antenna, cable and

VCR signals. Conversely, poor quality signals are

likely to result in caption errors or no captions at all.

Common signal conditions which may cause captions

errors are listed below:

•

Make sure ...

TV/VCR power must be turned on.

•

Automobile ignition noise

Electric motor brush noise

Weak snowy reception on TV screen

Multiplex signal reception displaying picture

•

1 Select “PICTURE CONTROL”

– M E N U –

•

TIMER PROGRAMMING

Press the MENU button on the

PICTURE CONTROL

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

remote control.

ghosts or airplane flutter.

Press the PLAY/K or STOP/L but-

ton to point to ”PICTURE CON-

TROL”.

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

Playback of poorly recorded or worn VCR tapes.

NOTE:

•

TIME SEARCH

INDEX SEARCH

If the TV/VCR displays a black box on the TV

screen, this means that the TV/VCR

is set to the TEXT mode. To clear

screen, select [CAPTION1], [CAP-

TION2] or [OFF].

Then, press the F.FWD/B button.

2 Select item you want to adjust

Press the PLAY/K or STOP/L but-

ton until desired control is dis-

played.

Make sure ...

TV/VCR power must be turned on.

•

BRIGHT / CONTRAST /

COLOR / TINT /

SHARPNESS

BRIGHT

–

P +

– M E N U –

1 Select “CAPTION”

TIMER PROGRAMMING

PICTURE CONTROL

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

Press the MENU button on the

remote control.

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

3 Adjust the picture control

Press the F.FWD/B or REW/s button to adjust to

your desired level.

Press the PLAY/K or STOP/L but-

ton to point to “CAPTION”.

ZERO RETURN

TIME SEARCH

INDEX SEARCH

REW/s

to decrease

brightness

to decrease

contrast

F.FWD/B

to increase

brightness

to increase

contrast

2 Select your desired caption menu

– M E N U –

BRIGHT

Press the F.FWD/B or REW/s

TIMER PROGRAMMING

PICTURE CONTROL

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

button until your desired caption

menu appears.

([CAPTION1], [CAPTION2],

[TEXT1] or [TEXT2])

CONTRAST

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [CAPTION1]

ZERO RETURN

TIME SEARCH

INDEX SEARCH

COLOR

TINT

to pale

to brilliant

to purple

SHARPNESS to soft

to green

to clear

3 Exit the caption setting mode

Press the MENU button on the remote control to

return to TV mode.

If there is a power failure of any kind, the unit will

retain its memory for this feature.

•

- 15 -

8H30

Download from Www.Somanuals.com. All Manuals Search And Download.

TO CANCEL THE CLOSED CAPTION

SYSTEM

Repeat steps [1] and [2], select [OFF] using the

F.FWD/B or REW/s button. Press the MENU but-

ton on the remote control to return to TV mode.

3 Select your desired item

Press the PLAY/K or STOP/L but-

ton to point to your desired item.

Then, press the F.FWD/B button to

select [BLOCK] or [VIEW].

TV–Y

TV–Y7

TV–G

TV–PG (

TV–14

TV–MA(

[VIEW]

(

)

(

When you select the rating category and turn it

WHEN THE CLOSED CAPTION MODE

IS ON

The On-Screen Display will disappear after 5 sec-

onds.

•

[BLOCK], the higher rating will turn [BLOCK]

automatically. Also, the lower rating will turn

[VIEW] automatically.

When you turn “TV-Y” to [VIEW], then all ratings

will turn to [VIEW] automatically.

This is also true when the MUTE button is pressed,

and when the PAUSE/STILL button is pressed

while recording.

•

Selection

TV-Y

Rating Category Explanations

Appropriate for all children

If there is a power failure of any kind, the unit will

retain its memory for this feature.

•

TV-Y7

TV-G

Appropriate for children seven and older

General Audience

TV-PG

TV-14

Parental Guidance suggested.

Unsuitable for children under 14

V-CHIP SET UP

TV-MA Mature audience only

V-CHIP enables parents to prevent their children

from watching inappropriate material on TV.

V-CHIP reads the ratings for programming (except

for news and sports programs, unedited movies on

premium cable channels, and Emergency Broadcast

System signals), then denies access to programming

if the program’s rating meets the limitations you

select. In this case, “PROTECTED PROGRAM by

...” message appears on the TV screen.

When you select TV-Y7, TV-PG, TV-14, or TV-MA

and you press the F.FWD/B button, the sub-ratings

will appear on the TV screen.

If you select the rating category (example: TV-PG)

and turn it [BLOCK] or [VIEW], the sub-ratings

(example: V for Violence) will turn [BLOCK] or

[VIEW] automatically.

You can set the sub-ratings to [BLOCK] or [VIEW]

individually when the rating category is set to

[BLOCK].

To set the sub-ratings individually, follow the steps

below.

To block certain ratings, follow the steps below.

Programming may be rated by the Motion Picture

•

Association of America (MPAA) or according to

the Television Parental Guidelines. In order to

block any inappropriate programming, set your

limits in both places (MPAA RATING and TV

RATING).

When you select [TV-Y7]:

Press the STOP/L or PLAY/K

•

button to select “FV” (Fantasy

Violence).

TV–Y7

[BLOCK]

Then, press the F.FWD/B button

to select [BLOCK] or [VIEW].

When you select [TV-PG], [TV-

14] or [TV-MA]:

Press the STOP/L or PLAY/K button to select

TV RATING SET UP

Make sure ...

•

TV/VCR power must be turned on.

•

“D”(Suggestive Dialog),

“L”(Coarse Language),

1 Select “V-CHIP SET UP”

– M E N U –

TIMER PROGRAMMING

TV–PG

[BLOCK]

PICTURE CONTROL

Press the MENU button on the

SETTING CLOCK

[BLOCK]

CHANNEL SET UP

“S”(Sexual Situation), or

“V”(Violence). Then, press the

F.FWD/B button to select

[BLOCK] or [VIEW].

Note: When you select [TV-MA], “D” does not

appear on the TV screen.

remote control.

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

Press the PLAY/K or STOP/L but-

ton to point to “V-CHIP SET UP”.

Then, press the F.FWD/B button.

INDEX SEARCH

2 Select “TV RATING”

Press the PLAY/K or STOP/L but-

ton to point to “TV RATING”.

Then, press the F.FWD/B button.

The sub-ratings which set to

[BLOCK] appears next to the rat-

ing category in the TV RATING

menu.

•

– V-CHIP SET UP –

TV RATING

MPAA RATING

TV–Y

TV–Y7

TV–G

TV–PG (DLSV)

TV–14 (DLSV)

TV–MA ( LSV)

[VIEW]

(

)

[VIEW]

[BLOCK]

- 16 -

8H30

Download from Www.Somanuals.com. All Manuals Search And Download.

4 Exit the V-Chip setting mode

Press the MENU button on the remote control to

return to original mode.

3 Select your desired item

Press the PLAY/K or STOP/L but-

ton to point to your desired item.

Then, press the F.FWD/B button

to select [BLOCK] or [VIEW].

[VIEW]

PG–13

NC–17

[VIEW]

[BLOCK]

MPAA RATING SET UP

Selection

Rating Category Explanations

General Audience

Make sure ...

TV/VCR power must be turned on.

•

PG-13

Parental Guidance suggested.

Unsuitable for children under 13

Restricted; under 17 requires accompa-

nying parent or adult guardian

No one under 17 admitted

1 Select “V-CHIP SET UP”

– M E N U –

TIMER PROGRAMMING

PICTURE CONTROL

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

Press the MENU button on the

remote control.

NC-17

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

Press the PLAY/K or STOP/L but-

ton to point to “V-CHIP SET UP”.

Then, press the F.FWD/B button.

Mature audience only

INDEX SEARCH

When you select the rating category and turn it

[BLOCK], the higher rating will turn [BLOCK]

automatically. Also, the lower rating will turn

[VIEW] automatically.

•

– V-CHIP SET UP –

2 Select “MPAA RATING”

Press the PLAY/K or STOP/L but-

ton to point to “MPAA RATING”.

Then, press the F.FWD/B button.

TV RATING

MPAA RATING

When you turn “G” to [VIEW], then all ratings

will turn to [VIEW] automatically.

•

4 Exit the V-Chip setting mode

Press the MENU button on the remote control to

return to original mode.

PLAYBACK

This TV/VCR will operate with any cassette that has the

mark. For best results, we

recommend the use of high-quality tapes. Do not use poor quality or damaged tapes.

INSERTING A CASSETTE

Insert the cassette in the direction as shown. Push in

gently, but continuously, on the center-back of the

cassette until it is drawn into the TV/VCR. The

TV/VCR will automatically turn on.

NORMAL PLAYBACK

Make sure ...

TV/VCR power must be turned on.

•

1 Insert a prerecorded tape

If the erase-protection tab has been removed, the

TV/VCR will start playback automatically.

Window

WRONG

PLAY

CORRECT

2 To begin playback

Press the PLAY button.

PRECAUTIONS

Note: If any menu is activated on

the screen, the PLAY button does

not function. Press the MENU but-

Avoid moisture. Moisture condensation may occur

•

on the tape if it is moved from a cold place to a

warm place or visa versa. Before using a tape with

these conditions, to avoid damage of the tape and

your TV/VCR, wait until the tape has warmed to

room temperature and the moisture has evaporated.

ton to clear the menu, then press the PLAY button.

If a tape is already in the TV/VCR with the power

off, do either of the following:

A) Press the PLAY button on the TV/VCR. Power

will automatically turn on and playback will start.

B) Press the POWER button on the remote control to

turn the TV/VCR on, then press the PLAY button

on the remote control and playback will start.

Avoid extreme heat, high humidity and magnetic

•

fields.

Do not tamper with the cassette mechanism.

Do not touch the tape with your fingers.

•

- 17 -

8H30

Download from Www.Somanuals.com. All Manuals Search And Download.

STOP

3 To stop playback

Press the STOP button when play-

back is completed.

PICTURE SEARCH

This feature is very useful in finding or skipping over

a particular scene on a tape. In this mode, the sound

will be muted.

1)You may view a video tape at a high speed in

either a forward or reverse direction by pressing

the F.FWD or REW button during playback (in the

SP / LP / SLP modes).

2)Press it again and the TV/VCR will now search in

super high speed (in the LP / SLP modes only).

NOTE: Tapes recorded in the SP or LP mode will

display a noise bar on the TV screen and the pic-

ture may revert to Black and White. This is normal.

3)Press the PLAY button to return to normal speed.

AUTO REPEAT PLAYBACK

The TV/VCR has an auto repeat function that allows

you to repeat a tape indefinitely without touching the

PLAY button.

ALL REPEAT: Repeat playback from the beginning

to the end of the tape.

BLANK REPEAT: Repeat playback from the begin-

ning to a blank part of more than 10 seconds.

ZERO RETURN

This function allows you to search easily a beginning

point that you want to review by rewinding or fast

forwarding.

1 Select “USER’S SET UP”

– M E N U –

Press the MENU button on the

TIMER PROGRAMMING

PICTURE CONTROL

remote control.

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

Press the PLAY/K or STOP/L but-

ton to point to “USER’S SET UP”.

Then, press the F.FWD/B button.

NOTE:

Zero Return WILL NOT work on a blank tape or a

blank portion of a tape.

INDEX SEARCH

2 Select “ALL” or “BLANK”

1 Stop a tape at your desired point

Rewind or fast forward the tape to the beginning

point from which you want to review.

Press the PLAY/K or STOP/L button to point to

“REPEAT PLAY”.

USER’S SET UP

–

Press the F.FWD/B or REW/s

button repeatedly until your desired

selection [ALL] or [BLANK]

appears.

RENTAL

REPEAT PLAY

AUTO RETURN

[OFF]

[ALL]

[OFF]

2 Reset the counter to 0:00:00

Press the COUNTER RESET button repeatedly.

3 Exit the Repeat Play setting

Press the MENU button on the remote control to

return to the TV mode.

3 Begin recording or playback

Press the RECORD or PLAY button.

Press the STOP button when recording or playback is

completed.

4 Start playback

Press the PLAY button to start the Repeat Play.

”REPEAT PLAY B” appears.

•

4 To activate “ZERO RETURN” mode

Press the MENU button on the remote control.

Press the PLAY/K or STOP/L button to point to

Once you select the Repeat Play mode, it stays in

effect even after you turn off the TV/VCR.

If the Rental mode is set [ON], the “RENTAL

PLAY B” display has priority.

“ZERO RETURN”.

Then, press the F.FWD/B button.

The counter will appear on the TV

screen.

– M E N U –

TIMER PROGRAMMING

•

PICTURE CONTROL

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

INDEX SEARCH

The tape will automatically stop

TO CANCEL THE REPEAT PLAY MODE

when the counter returns to 0:00:00.

Repeat steps [1] and [2], select [OFF] using the

F.FWD/B or REW/s button on the remote control.

Press the MENU button on the remote control to

return to TV mode.

If there is a power failure of any kind, the unit

will retain its memory for this feature.

TIME SEARCH

The Time Search function makes it possible to

quickly advance the tape to your desired position

simply by entering the exact amount of playback

time you want to skip.

- 18 -

8H30

Download from Www.Somanuals.com. All Manuals Search And Download.

NOTES:

SLOW MOTION

Time Search can be set up to a maximum of 9

hours 50 minutes (9:50) by 10 minutes at a time.

•

Press the SLOW button to reduce the playback speed.

The TV/VCR mutes the sound during slow motion.

Press the PLAY button to return to normal playback.

NOTE: If left in the Slow mode for more than five

minutes, the TV/VCR will automatically go into the

Stop mode.

This function will not operate in recording mode.

•

In the example below: To watch a program that is 2

hours, 50 minutes from the present tape position, in

either direction.

1 Insert a tape.

RENTAL PLAYBACK

2 Select “TIME SEARCH” mode

Press the TIME SEARCH button (with each push it

will increase by 10 minute).

This function enables you to improve the picture

quality when playing back worn cassettes such as

rented tapes.

3 Enter your desired time

TIME SEARCH

2 : 50

1 Select “USER’S SET UP”

Press the PLAY/K or STOP/L but-

– M E N U –

Press the MENU button on the

TIMER PROGRAMMING

ton until your desired time appears.

(Example: “2:50” stands for 2 hours

50 minutes)

If you wish to cancel the Time Search at this point,

press the MENU button on the remote control.

PICTURE CONTROL

SETTING CLOCK

remote control.

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

Press the PLAY/K or STOP/L but-

ton to point to “USER’S SET UP”.

Then, press the F.FWD/B button.

INDEX SEARCH

USER’S SET UP

–

2 Set “RENTAL” to [ON]

Press the PLAY/K or STOP/L but-

ton to point to “RENTAL”.

Press the F.FWD/B or REW/s

button until [ON] appears.

4 Begin Time Search

By pressing the REW/s or F.FWD/B button, the

TV/VCR will rewind or fast forward to the specified

point.

RENTAL

REPEAT PLAY

AUTO RETURN

[ON]

[OFF]

The time counts down as the searching progresses.

When 0:00 is reached, the tape will start playback

automatically.

3 Exit the Rental setting

Press the MENU button on the remote control to

return to the TV mode.

TO CANCEL THE TIME SEARCH at this

point

Press the STOP/EJECT button on the TV/VCR or the

remote control. This will delete the selected time.

4 Start playback

Press the PLAY button to start playback. “RENTAL

PLAY B” appears.

Once you select the Rental mode, it stays in effect

even after you turn off the TV/VCR.

INDEX SEARCH

An index signal is recorded on the tape automatically

when the recording is started. To view a recording at a

specific start point:

1)Press the MENU button on the

CHANNEL SET UP

remote control. Press the

USER’S SET UP

PLAY/K or STOP/L button to

point to “INDEX SEARCH”,

then press the F.FWD/B button.

2)Press the PLAY/K or STOP/L button within 30

seconds until the number of programs that you

want to skip appears.

•

TO CANCEL THE RENTAL MODE

– M E N U –

TIMER PROGRAMMING

Repeat steps [1] and [2], select [OFF] using the

F.FWD/B or REW/s button on the remote control.

Press the MENU button on the remote control to

return to TV mode.

If there is a power failure of any kind, the unit

will retain its memory for this feature.

PICTURE CONTROL

SETTING CLOCK

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

INDEX SEARCH

3)Press the F.FWD/B or REW/s button to start

index search. If you want to go forward, press the

F.FWD/B button. If you want to go back, press

the REW/s button.

After index search, the TV/VCR will play the tape

automatically.

•

In some cases, the index mark at the beginning of

video tape cannot be detected.

•

- 19 -

8H30

Download from Www.Somanuals.com. All Manuals Search And Download.

VERTICAL HOLD CONTROL

TRACKING ADJUSTMENT

In the Pause/Still mode only, when the picture begins

to vibrate vertically, stabilize the picture by pressing

the CHANNEL K or L button.

Tracking adjustment will be set automatically

(Digital Tracking function) when you start play-

back.

•

NOTE:

However when playing pre-recorded tapes or tapes

recorded on units other than your own, noise lines

(black and white streaks) may appear on the play-

back picture. If this occurs, you can adjust the

tracking control manually by pressing the CHAN-

NEL K or L button until the streaks disappear. To

return to the DTR function, stop the tape once and

start playback again.

You can reduce the noise lines by pressing the

CHANNEL K or L button in slow mode, too.

Tracking adjustment in Slow mode will not be set

automatically.

If there are video noise lines on the screen, see Tracking

Adjustment section.

STILL PICTURE

You can view a still picture on the TV screen during

playback (the Still mode). Press the PAUSE/STILL

button during playback. Only tapes recorded in the

SLP mode will show the least amount of lines. Press

the PLAY button to return to playback.

NOTES:

•

You can advance the picture one frame at a time by

pressing the PAUSE/STILL button during the Still

mode.

If it is left in the Still mode for more than five min-

utes, the TV/VCR will automatically switch to the

Stop mode.

•

NOTE:

In Still mode, press the SLOW button and press the

CHANNEL K or L button until streaks disappear.

To return to Still mode, press the PAUSE/STILL

button again.

•

RECORDING

Make sure ...

Before recording, make sure:

TV/VCR power is turned on.

•

The desired channel is selected by pressing the num-

ber buttons on the remote control or the CHANNEL

Up/Down button. (If the TV/VCR is connected to a

cable box or satellite box, the TV/VCR must be on

CH3 or CH4, then the channel to be recorded is

selected on the cable box or satellite box. )

There is a tape with its safety tab into the VCR.

The desired recording speed is selected in SP(stan-

dard play) or SLP(super long play) mode by press-

ing the TAPE SPEED button on the VCR.

Insert a cassette tape with its erase prevention tab

in place. (If necessary, rewind or fast forward the

tape to the point at which you want to begin

recording.)

NOTE: This unit will ONLY record and view the

same channel.

NORMAL RECORDING

1)Begin the recording by pressing the RECORD but-

ton.

Tape Speed

Type of tape

SP mode

Recording/Playback Time

T60

1 hour

3 hours

T120

T160

To temporarily stop recording or resume it, press

the PAUSE/STILL button. After the VCR has been

in Pause mode for 5 minutes, it will stop automati-

cally to protect the tape and the video head.

NOTES:

2 hours 2-2/3 hours

6 hours 8 hours

SLP mode

ERASE PREVENTION

You can prevent acciden-

tal erasing of recording

by breaking off the tab

on the back edge of the

cassette.

After five minutes, the TV/VCR will automatically

switch to the Recording mode to prevent tape

damage.

If “CLOSED CAPTION (ON)” is selected, the

On-Screen Display will appear for 5 seconds, then

disappear.

•

If you decide to record

on the tape again, cover

the hole with plastic

tape.

•

2)Stop the recording by pressing the STOP button

when recording is completed.

Tab

Plastic Tape

- 20 -

8H30

Download from Www.Somanuals.com. All Manuals Search And Download.

AAvoid overlap of programs ...

There is a chance that a program will not be record-

ed. When programs overlap:

OTR (One Touch Recording)

This function enables you to set the recording length

simply by pressing the REC/OTR button on the

VCR.

The program with the earliest start time will record

first.

•

Once the earliest program finishes recording, the

overlapping programs will record in the order of

the program number.

The illustration below demonstrates the sequence

of recording.

•

1)Begin OTR by pressing the

OTR(2 : 30)

REC/OTR button on the VCR

repeatedly until the desired

recording length appears.

•

Recording stops when 0:00 is

reached.

Recording Sequence

NOTES:

Program 1

10:00AM-11:00AM

Program 2

9:00AM-10:00AM

Program 3

This function CANNOT be done from the remote

•

control.

9:30AM-12:00PM

To stop the OTR operation, press the STOP button

on the TV/VCR or on the remote control.

•

9:00AM

10:00AM

11:00AM

12:00PM

*Recording period is SHADED

If the tape runs out before the end time, the

TV/VCR will switch to the Stop mode immediate-

ly, eject the tape and turn itself off.

•

1 Select “TIMER PROGRAMMING”

Press the MENU button on the

– M E N U –

Push(es) Display

1 push

Recording length

(continuous recording)

30 minutes

TIMER PROGRAMMING

PICTURE CONTROL

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

remote control.

Confirm “TIMER PROGRAM-

MING” is pointed to by pressing

the PLAY/K button.

V-CHIP SET UP

2 pushes

3 pushes

4 pushes

0:30

1:00

1:30

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

60 minutes

90 minutes

TIME SEARCH

INDEX SEARCH

Press the F.FWD/B button.

If you have not yet set the clock, “MANUAL

CLOCK SET” appears. If so, follow stops [3] to

[8] on page 11. Then set the timer recording.

•

17 pushes

8:00

480 minutes

TIMER RECORDING

2 Select your desired program position (1~8)

You may set the TV/VCR to start and end a record-

ing while you are away. You can set 8 programs to

record on specific days, daily or weekly within a 1

year period.

– TIMER PROGRAMMING –

Press the PLAY/K or STOP/L

button to select the desired pro-

gram position.

CH DATE

BEGIN END

- - -/- - - - - -:- -

-:- - - -

Then, press the F.FWD/B button.

In the example below, the timer is being set to record:

DATE:

July 6th, 2001

SETTING TIME: from 7:30PM to 8:50PM

3 Set the channel number

CHANNEL:

TAPE SPEED:

CH61

Press the PLAY/K or STOP/L button until the

desired channel number appears.

(Example: CH61)

Then, press the F.FWD/B button.

Remember:

If your TV/VCR is connected to a

cable or satellite box, you must set

– TIMER PROGRAMMING –

CH DATE BEGIN END

Make sure ...

If your TV/VCR is connected to a cable or satellite

box, you must set the TV/VCR to channel 3 or 4

to match the output channel of the box.

Clock is set to the correct time and date before set-

ting the timer.

TV/VCR power is turned on to program it.

To insert a cassette tape with its erase prevention

tab in place. (If necessary, rewind or fast forward

the tape to the point at which you want to begin

recording.)

•

- - -/- - - - - -:- -

61 -/- - - - - -:- -

- - -/- - - - - -:- -

-:- - - -

•

the TV/VCR to channel 3 or 4 to match the output

channel of the box.

•

4 Select once, every day or weekly recording

For once recording :

– TIMER PROGRAMMING –

CH DATE

BEGIN END

To set the channel you want to record

Press the PLAY/K (up) button

until the desired date appears.

(Example: “7/06” for July 6th).

Then, press the F.FWD/B but-

ton.

•

- - -/- - - - - -:- -

61 7/06 FRI -:- -

- - -/- - - - - -:- -

-:- - - -

- 21 -

8H30

Download from Www.Somanuals.com. All Manuals Search And Download.

For every day recording : To

record a TV program at the same

time on the same channel every

day. (Example: Monday through

Sunday)

– TIMER PROGRAMMING –

CH DATE BEGIN END

10 Finish setting the program

Press the F.FWD/B or REW/s button. The program

is now completed.

- - -/- - - - - -:- -

61 EVRY DAY -:- -

- - -/- - - - - -:- -

-:- - - -

To set another program, repeat steps [2] to [10].

Press the MENU button on the remote control to

•

Press the STOP/L (down) but-

ton until “EVRY DAY” appears. Then, press the

F.FWD/B button.

return to original mode.

11 Set the timer

For weekly recording : To record a TV program at

the same time on the same channel every week.

Press the POWER button to set automatic timer

recording. The TIMER REC indicator lights up.

(Example: every Monday)

You must turn off the TV/VCR to activate automat-

ic timer recording.

– TIMER PROGRAMMING –

•

CH DATE

BEGIN END

Press the STOP/L (down) button

until “EVRY” and your desired

day of the week appear together.

Then, press the F.FWD/B but-

ton.

- - -/- - - - - -:- -

61 EVRY MON -:- -

- - -/- - - - - -:- -

-:- - - -

If power is not turned off and you continue watch-

ing TV, “TIMER REC STANDBY” starts flashing

on the TV screen 2 minutes before the programmed

start time.

– TIMER PROGRAMMING –

CH DATE BEGIN END

5 Set beginning hour

TIMER PROGRAM EXTENSION

Press the PLAY/K or STOP/L but-

ton until the desired hour appears.

(Example: “ 7, PM” for 7:30PM)

Then, press the F.FWD/B button.

- - -/- - - - - -:- -

-:- - - -

61 7/06 FRI 7:12^P

- - -/- - - - - -:- -

To shift the time schedule of an automatic timer

recording.

1)Press the POWER button.

2)Repeat step [1] on page 21.

6 Set beginning minute

– TIMER PROGRAMMING –

CH DATE BEGIN END

3)Press the RECORD button and select the desired

program using the PLAY/K or STOP/L button.

4)Press the RECORD button again.

Each additional push will shift forward the

begin/end time for recording by 10 minutes. When

the recording is already in progress, each additional

push will shift forward the end time only. If you

want to cancel while setting, press the

PAUSE/STILL button on the remote control. The

recording time returns to the original time.

NOTE: When you shift forward the time schedule

during recording, the recording speed will automati-

cally be set to the SLP mode.

Press the PLAY/K or STOP/L but-

ton until the desired minute appears.

(Example: “30” for 7:30PM)

- - -/- - - - - -:- -

-:- - - -

61 7/06 FRI 7:30^P

- - -/- - - - - -:- -

Then, press the F.FWD/B button.

– TIMER PROGRAMMING –

CH DATE BEGIN END

7 Set end hour

Press the PLAY/K or STOP/L but-

ton until the desired hour appears.

(Example: “8, PM” for 8:50PM)

Then, press the F.FWD/B button.

- - -/- - - - - -:- -

-:- - - -

8:30^PM - -

-:- - - -

61 7/06 FRI 7:30^P

- - -/- - - - - -:- -

– TIMER PROGRAMMING –

CH DATE BEGIN END

8 Set end minute

5)Press the F.FWD/B or REW/s button to exit the

setting menu. Then press the MENU button on the

remote control to return to original mode.

Press the PLAY/K or STOP/L but-

ton until the desired minute appears.

(Example: “50” for 8:50PM)

Then, press the F.FWD/B button.

- - -/- - - - - -:- -

-:- - - -

8:50^PM- -

-:- - - -

61 7/06 FRI 7:30^P

- - -/- - - - - -:- -

TO CORRECT A PROGRAM

While setting a program; press the REW/s but-

ton to go back one step and enter the correct num-

•

– TIMER PROGRAMMING –

CH DATE BEGIN END

9 Set the tape speed

Press the PLAY/K or STOP/L but-

ton until the desired tape speed

appears. (Example: SP)

bers using the PLAY/K or STOP/L button.

After setting a program;

1)Press the POWER button.

- - -/- - - - - -:- -

-:- - - -

8:50^PMSP

-:- - - -

•

61 7/06 FRI 7:30^P

- - -/- - - - - -:- -

2)Repeat steps [1] - [2] on page 21.

3)Press the F.FWD/B button (or press the REW/s

button to go back one step) until the part you

want to correct begins flashing, then make the

changes pressing the PLAY/K or STOP/L but-

ton.

4)Press the POWER button to set automatic timer

recording.

- 22 -

8H30

Download from Www.Somanuals.com. All Manuals Search And Download.

TO CANCEL AN AUTOMATIC TIMER

RECORDING

USER’S SET UP

–

2 Set “AUTO RETURN” to [ON]

Press the PLAY/K or STOP/L but-

ton to point to “AUTO RETURN”.

Press the F.FWD/B or REW/s

button until [ON] appears. Then,

After setting a program;

1)Press the POWER button.

•

RENTAL

REPEAT PLAY

AUTO RETURN

[OFF]

[ON]

2)Repeat steps [1] ~ [2] under TIMER RECORD-

ING, page 21, and select a program you want to

cancel.

3)Press the T-PROG. CLEAR button.

4)Press the MENU button on the remote control to

return to TV mode.

press the MENU button on the remote control to

return to TV mode.

3 Auto Return will begin

While recording is in progress;

1)Press POWER button.

•

When all the timer recordings are completed, the

TV/VCR will rewind to the beginning of the recorded

2)Press the STOP/EJECT button on the TV/VCR.

program(s).

NOTE:

TO CHECK THE BEGIN/END TIME

1)Press the POWER button so that the REC indicator

goes off.

If you press the POWER button while tape is

•

rewinding, the Auto Return will stop.

2)Press the MENU button on the remote control.

3)Confirm “TIMER PROGRAMMING” is pointed

to.

4 Watch the recorded program

Press the PLAY button.

4)Press the F.FWD/B button. The details of pro-

grams appear on the TV screen.

5)Press the MENU button on the remote control to

return to TV mode.

TO CANCEL THE AUTO RETURN

MODE

Repeat steps [1] and [2], select [OFF] using the

F.FWD/B or REW/s button. Then, press the MENU

button on the remote control to return to TV mode.

If there is a power failure of any kind, the unit

will retain its memory for this feature.

HINTS FOR AUTOMATIC

TIMER RECORDING

Make sure the channel you want to record is prop-

erly set in advance.

•

It is not necessary to press the RECORD button for

timer recording.

•

WAKE UP TIMER

Recording begins automatically at the Start time.

If you are recording using a Timer mode, you may

not operate the unit manually.

•

The Wake Up Timer function turns on the TV/VCR

without using the POWER button after a desired

period of time.

The erase-prevention tab on the cassette must be in

place (or you must put tape over the hole).

If the erase-prevention tab is removed, the cassette

will be ejected when the POWER button is pressed

to off.

If the tape runs out before the end time, the

TV/VCR will switch to the Stop mode immediate-

ly, and the tape will be ejected.

NOTES:

•

Use the remote control for this procedure.

Clock must be set to the correct time before setting

the timer.

•

If you want to select [TAPE], you must insert a

cassette tape in the TV/VCR. The tape will start

playback automatically on your desired time.

•

1 Select “WAKE UP TIMER”

Press the WAKE-UP/SLEEP button

on the remote control once, and

confirm “ON/OFF” is pointed.

Press the F.FWD/B or REW/s

button until [ON] appears.

AUTO RETURN

With this feature, after timer recording is finished,

the beginning of the recorded program(s) can be

searched for automatically.

WAKE UP B ON/OFF

[ON]

TIMER

TV/TAPE

TIME

[TV]

[12:00AM]

– M E N U –

1 Select “USER’S SET UP”

TIMER PROGRAMMING

PICTURE CONTROL

SETTING CLOCK

Press the MENU button on the

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

remote control.

Press the PLAY/K or STOP/L but-

ton to point to “USER’S SET UP”.

Then, press the F.FWD/B button.

INDEX SEARCH

- 23 -

8H30

Download from Www.Somanuals.com. All Manuals Search And Download.

SLEEP TIMER

2 Select “TV” or “TAPE”

The Sleep Timer function turns off the TV/VCR

without using the POWER button after a desired

period of time.

Press the PLAY/K or STOP/L but-

ton until it points to “TV/TAPE”.

Press the F.FWD/B or REW/s

button, and select [TV] or [TAPE].

WAKE UP

TIMER

ON/OFF

B TV/TAPE

TIME

[ON]

[TV]

NOTE:

[12:00AM]

This function does not operate during Recording

•

mode.

3 Set wake up time

1 Select “SLEEP TIMER”

Press the PLAY/K or STOP/L but-

ton until it points to “TIME”.

Press the F.FWD/B or REW/s

button until your desired wake up

time appears.

Press the WAKE UP/SLEEP button on the remote

control until “SLEEP TIMER” appears.

WAKE UP

TIMER

ON/OFF

TV/TAPE

B TIME

[ON]

[TV]

[12:00AM]

2 Set sleep time

Press the PLAY/K, STOP/L,

F.FWD/B or REW/s button until

your desired sleep time appears.

Each additional push will increase (or decrease) the

time by 10 minutes.

SLEEP TIMER [2:00]

Each additional push will increase

4 Exit the Wake Up Timer setting

Press the MENU button on the remote control to

return to TV mode.

the time by 30 minutes up to 120 minutes.

Press the MENU button on the remote control to exit

the Sleep Timer setting.

TO CANCEL THE WAKE UP TIMER

TO CANCEL THE SLEEP TIMER

Press the WAKE-UP/SLEEP button on the remote

control once, and confirm “ON/OFF” is pointed.

Press the F.FWD/B or REW/s button until [OFF]

appears.

Press the WAKE UP/SLEEP button on the remote

control until “SLEEP TIMER” appears.

To view the time left for sleep timer, press the

WAKE-UP/SLEEP button twice, then press the

MENU button on the remote control to exit the sleep

timer setting.

COPYING A VIDEO TAPE

You can make copies of video tapes made by friends

or relatives for your enjoyment.

1)Insert a pre-recorded video cassette into the Source

(Playing) VCR or camcorder.

2)Insert a blank video cassette, or one you want to

record over, into the TV/VCR’s cassette compart-

ment.

3)Press the SPEED button on remote control for the

TV/VCR to select the desired recording speed

(SP/SLP).

WARNING: Unauthorized recordings of

copyrighted video tapes may be an

infringement of copyright laws.

Connect your TV/VCR and a Source (Playing) VCR

using the following diagram.

4)Press the CHANNEL K or L button on the

TV/VCR until “AUX” appears on the screen.

NOTE: “AUX” is found below the lowest numbered

memorized channel. (Example: CH2)

5)Press the RECORD button on the TV/VCR.

6)Begin playback of the tape in the source (Playing)

VCR or camcorder.

AUDIO

VIDEO

STOP/EJECT

[The TV/VCR]

NOTE: For best results during copying, use the

TV/VCR’s front panel controls whenever possible.

The remote control might affect the source (Playing)

VCR’s playback operation.

[Ex: Source (playing)

VCR or camcorder]

VIDEO

Audio/Video

adapter cable

(not supplied)

OUT

AUDIO

- 24 -

8H30

Download from Www.Somanuals.com. All Manuals Search And Download.

ON SCREEN DISPLAY

To check the Counter, Clock and Channel number on the TV screen, press the DISPLAY button on the remote

control. Each time you press the DISPLAY button on the remote control, the TV screen will change as follows:

WHEN THE CLOSED CAPTION MODE IS OFF:

Counter mode: After 5 seconds, only

the counter remains. To clear it, press

the DISPLAY button.

Clock mode: After 5 seconds, only

the clock and the channel number

remain. To clear them, press the DIS-

PLAY button.

•

5:40PM

CH2

Press

once

Press

once

COUNT 0:12:34

Press once

OFF mode

Clock/Counter mode

WHEN THE CLOSED CAPTION MODE IS ON:

The On Screen Display disappears after 5 seconds.

•

STOP

5:40 PM

CH2

This is true even if the MUTE button is pressed, or the

•

PAUSE/STILL button is pressed while recording.

COUNT 0:12:34

SPECIAL FEATURES

REAL TIME TAPE COUNTER

AUTO REWIND-EJECT

This shows the elapsed recording or playback time in

When the end of a tape is reached during record-

ing, playback, or fast-forward, the tape will auto-

matically rewind to the beginning. After rewinding

finishes, the TV/VCR will eject the tape and turn

itself to off.

This function is operative when Repeat Play is set

to the [OFF] position.

•

hours, minutes, and seconds. (The displayed time

will not change on a blank tape or blank portions on

the tape.)The “–” indication will appear when the

tape has rewound further than “0:00:00” on the tape

counter.

•

The tape will not auto-rewind during timer record-

ing or One Touch Recording.

MAINTENANCE

back, the video heads in your TV/VCR may need

to be cleaned.

CABINET CLEANING

Wipe the front panel and other exterior surfaces of

the TV/VCR with a soft cloth immersed in luke-

warm water and wrung dry.

•

1.Please visit your local Audio/Video store and pur-

chase a good quality VHS Video Head Cleaner.

2.If a Video Head Cleaner does not solve the prob-

lem, please call our help line at 1-800-968-3429, to

locate an Authorized Service Center.

NOTES:

Remember to read the instructions included with

the video head cleaner before use.

Clean video heads only when problems occur.

Never use a solvent or alcohol. Do not spray insec-

•

ticide liquid near the TV/VCR. Such chemicals

may cause damage and discoloration to the

exposed surfaces.

•

AUTO HEAD CLEANING

•

Automatically cleans video heads as you insert or

remove a cassette, so you can see a clear picture.

•

SERVICING

Should your TV/VCR become inoperative, do not

try to correct the problem by yourself. There are no

user-serviceable parts inside. Turn off, unplug the

power cord, and please call our help line at 1-800-

968-3429, to locate an Authorized Service Center.

Playback picture may become blurred or interrupt-

•

ed while the TV program reception is clear. Dirt

accumulated on the video heads after long periods

of use, or the usage of rental or worn tapes can

cause this problem.

If a streaky or snowy picture appears during play-

- 25 -

8H30

Download from Www.Somanuals.com. All Manuals Search And Download.

TROUBLESHOOTING GUIDE

If you have followed the instructions contained in this manual and have difficulty in operating your TV/VCR,

locate the PROBLEM in the left column below. Check the corresponding CORRECTIVE ACTION column to

remedy the problem.

PROBLEM

CORRECTIVE ACTION

No power.

Make sure the AC cord is connected to an AC outlet.

Make sure the car battery cord is connected to vehicle’s cigarette

lighter socket and to DC 13.2V (12V) jack on back of the TV/VCR.

Check the fuse (5A, 250V) in car battery cord.

Make sure the power is turned on.

Make sure the AC cord is connected to an AC outlet.

Check antenna connection.

Let the TV/VCR program its tuner memory.

Adjust direction or replace antenna.

Adjust picture controls.

Adjust volume control on remote control or main unit.

Press the MUTE button to restore sound.

Make sure the timer recording is set correctly.

Make sure the power is off.

•

No picture and sound.

No picture or poor picture on

TV/VCR.

No sound or poor sound.

•

Timer recording is not possible.

Make sure the TV/VCR clock is set correctly.

Make sure the tape has an erase-prevention tab. If need, cover the

hole with plastic tape.

Cannot go into Record mode.

•

Playback picture is partially noisy.

Adjust tracking control for a better picture using the CHANNEL

or L button on the TV/VCR.

•

No picture but the audio is OK in

playback.

No operation by infrared Remote

Control.

Video or color fades in and out

when making a copy of a video tape

Head cleaning may be necessary. Refer to “AUTO HEAD

CLEANING” on page 25.

Make sure the AC cord is connected to an AC outlet.

Check batteries in remote control.

You can not copy a copyrighted video tape. You are experiencing

copy guard protection.

Make sure the AC cord is connected to an AC outlet.

•

Cannot set the auto clock to ON.

•

CLOSED CAPTION PROBLEM

My TV/VCR is showing captions

that are misspelled.

POSSIBLE REMEDY

• You are watching a live broadcast and spelling errors made by the

• closed captioning production company may pass through uncorrected.

• A prerecorded program will not show any misspelled words because

• of the normal time available for editing the captions.

My TV/VCR will not show the text • Captions that are delayed a few seconds behind the actual dialogue

in its entirety or there is a delay of • are common for live broadcast. Most captioning production companies

what is being said.

• can display a dialogue to a maximum of 220 words per minute. If a

• dialogue exceeds that rate, selective editing is used to insure that the

• captions remain up-to-date with the current TV screen dialogue.

• Interference caused by building, power lines, thunderstorms, etc.

• may cause scrambled or incomplete captions to appear.

My captions are scrambled with

white boxes on the TV screen.

My program guide listed a TV show • Broadcasters may at times use a time compression process to speed

as being closed captioned but none • up the actual program so that additional advertising time can be

of the captions were displayed.

• given. Since the decoder cannot read the compressed information,

• captions will be lost.

My prerecorded video tape does not • The video tape was either an illegal copy or the tape duplicating

show any captions. The tape box • company accidentally left out the captioning signals during the

mentions it being closed captioned. • copying process.

My TV screen shows a black box

on certain channels.

• You are in the TEXT mode. Select CAPTION mode to CAPTION

• [OFF].

- 26 -

8H30

Download from Www.Somanuals.com. All Manuals Search And Download.

SPECIFICATIONS

GENERAL SPECIFICATIONS

ELECTRICAL SPECIFICATIONS

Video input level :

Audio input level :

0.5~2.0Vp-p

-15dBs

CRT :

13 inch in-line gun, 90˚

deflection tube

NTSC-M

Video S/N ratio : More than 46dB

Audio S/N ratio : More than 43dB

Television system :

Closed caption system :§15.119/FCC

Video Heads :

Tape width :

Tape speed

SP :

LP :

SLP :

Tuner channel

TV VHF Low :

TV VHF High :

TV UHF :

CATV

Rotary four-head

1/2 inch

OTHER SPECIFICATIONS

Power requirement : AC 120V/60Hz

DC 13.2V

33.40mm/sec.

16.67mm/sec.

11.12mm/sec.

Power consumption : AC 65W / DC 75W

Dimensions :

H:15-13/16” (402mm)

W:15-3/16” (386mm)

D:14-7/8” (378mm)

27.6 lbs (12.5kg)

#2~#6

#7~#13

#14~#69

Weight :

VHF :

Designs and specifications are subject to change

without notice and without our legal obligation.

If there is a discrepancy between languages, the

default language will be English.

•

MID band :

SUPER band :

HYPER band :

Terminals

A5~A1, A~I

J~W

W+1~W+84

Antenna input :

VHF/UHF 75 ohms

unbalanced

Video input :

Audio input :

Earphone :

RCA connector [ 1

1/8” monaural (3.5 mm)

CABLE CHANNEL DESIGNATIONS

If you subscribe to cable TV, the channels are displayed as 1-125. Cable companies often designate channels

with letters or letter-number combinations. Please check with your local cable company. The following is a

chart of common cable channel designations.

CATV channel

TV Display

CATV channel

TV Display

CATV channel

W+1

W+2

W+3

W+4

W+5

W+6

W+7

W+8

W+9

TV Display

CATV channel

W+10 W+11 W+12 W+13 W+14 W+15 W+16 W+17 W+18 W+19 W+20 W+21 W+22 W+23 W+24

46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

W+25 W+26 W+27 W+28 W+29 W+30 W+31 W+32 W+33 W+34 W+35 W+36 W+37 W+38 W+39

61 62 63 64 65 66 67 68 69 70 71 72 73 74 75

W+40 W+41 W+42 W+43 W+44 W+45 W+46 W+47 W+48 W+49 W+50 W+51 W+52 W+53 W+54

TV Display

CATV channel

TV Display

CATV channel

TV Display

W+59 W+60 W+61 W+62 W+63 W+64

100 101 102 103 104 105

W+55 W+56 W+57 W+58

A-5

A-4

A-3

A-2

A-1

CATV channel

TV Display

CATV channel

W+65 W+66 W+67 W+68 W+69 W+70 W+71 W+72 W+73 W+74 W+75 W+76 W+77 W+78 W+79

TV Display

106

W+80 W+81 W+82 W+83 W+84

121 122 123 124 125

107

108

109

110

111

112

113

114

115

116

117

118

119

120

CATV channel

TV Display

- 27 -

8H30

Download from Www.Somanuals.com. All Manuals Search And Download.

INDICE

CONTROLES DE OPERACIÓN Y

SUS FUNCIONES . . . . . . . . . . . . . . . . . . . . . . . .28

INSTALACIÓN DE LAS PILAS . . . . . . . . . . . . .31

PREPARACIÓN DE CANALES POR

CONEXIONES DE ANTENA/CABLE . . . . . . . .30 PRIMERA VEZ . . . . . . . . . . . . . . . . . . . . . . . . . .31

MODO DE ENTRADA EXTERNA . . . . . . . . . . .31 AJUSTE DEL RELOJ . . . . . . . . . . . . . . . . . . . . .31

CONTROLES DE OPERACIÓN Y SUS FUNCIONES

NOTA:

No recomendamos utilizar mandos a distancia universales. No todas las funciones pueden ser controladas mediante un

mando a distancia universal. Si decide utilizar un mando a distancia universal con esta unidad, tenga en cuenta que con el

número de código dado tal vez no se pueda controlar la unidad. En este caso, póngase en contacto con el fabricante del

mando a distancia universal.

- PANEL DELANTERO -

AUDIO

VIDEO

STOP/EJECT

REW

PLAY F.FWD

REC/OTR

CHANNEL

VOLUME

POWER

8 9 10

12 13

[ Televisor/videograbadora ]

4 Botón de parada (STOP)– Púlselo para detener la

cinta.

- CONTROL REMOTO -

Botón de expulsión (EJECT)–Púlselo en el modo

de parada para expulsar la cinta del

televisor/videograbadora.

WAKE-UP

POWER

/SLEEP

EJECT

CHANNEL

RETURN

Botón L–

Púlselo para seleccionar los modos de ajuste desde el

menúde la pantalla.

Púlselo para introducir dígitos cuando establezca un

programa.

(Por ejemplo: Para ajustar el reloj o establecer un pro-

grama de temporizador)

[ Control remoto ]

•

CHANNEL

VOLUME

+100

DISPLAY

MUTE

PLAY

REW

F.FWD

4 Botón de expulsión (EJECT)–Púlselo en el modo

de parada para expulsar la cinta del

STOP

RECORD

SPEED PAUSE/STILL

televisor/videograbadora.

T-PROG.

CLEAR

GAME

SLOW

5 Botón de rebobinado (REW)– Púlselo para rebobi-

nar la cinta, o para ver la imagen en retroceso rápido

durante el modo de reproducción. (Búsqueda con

rebobinado)

COUNTER

RESET

Botón s–

1 Toma de auriculares (EARPHONE)– Para conec-

tar los auriculares (no suministrados) y escuchar en pri-

vado. La toma es mono y tiene un tamaño de 3,5 mm.

2 Toma de entrada de audio (AUDIO)– Conéctela a

la toma de salida de audio de su equipo de audio,

videocámara u otra videograbadora.

3 Toma de entrada de vídeo (VIDEO)– Conéctela a

la toma de salida de vídeo de su videocámara u otra

videograbadora.

Púlselo para seleccionar un modo desde un menúpar-

ticular.

(Por ejemplo: IDIOMA o ADJUST DE USER)

6 Botón de reproducción (PLAY)– Púlselo para ini-

ciar la reproducción.

•

Botón K–

Púlselo para seleccionar los modos de ajuste desde el

menúde la pantalla.

•

- 28 -

0I29

Download from Www.Somanuals.com. All Manuals Search And Download.

- PANEL TRASERO -

DC 13.2V

AC 120V

ANT.

27 28

Púlselo para introducir dígitos cuando establezca un

programa.

(Por ejemplo: Para ajustar el reloj o establecer un pro-

grama de temporizador)

7 Botón de avance rápido (F.FWD)– Púlselo para

avanzar rápidamente la cinta, o para ver la imagen en

avance rápido durante el modo de reproducción.

(Búsqueda con avance rápido)

14 Compartimiento del videocasete

•

15 Botones numerados– Púlselos para seleccionar los

canales deseados para ver o grabar. Para seleccionar

canales del 1 al 9, pulse primero el botón 0 y luego el

botón 1 a 9.

Botón +100– Cuando seleccione canales de tele-

visión por cable cuyo número sea superior al 99, pulse

primero este botón, y luego pulse los dos últimos dígi-

tos. (Para seleccionar el canal 125, pulse primero el

botón “+100” y luego el “2” y el “5”.)

Botón B–

Cuando establezca un programa (por ejemplo: para

ajustar el reloj o para establecer un programa de tem-

porizador), púlselo para determinar su elección y vaya

al paso siguiente que quiera introducir.

Púlselo para determinar los modos de ajuste desde el

menúde la pantalla.

•

16 Botón de menú (MENU)– Púlselo para visualizar el

menúprincipal en la pantalla del televisor.

17 Botón del visualizador (DISPLAY)– Visualiza el

contador o el número del canal actual y la hora actual

en la pantalla del televisor.

•

18 Botón de velocidad de cinta (SPEED)– Púlselo

Púlselo para seleccionar un modo desde un menúpar-

ticular.

para elegir la velocidad de grabación deseada: SP/SLP.

19 Botón T-PROG. CLEAR– Púlselo para cancelar un

(Por ejemplo: IDIOMA o ADJUST DE USER)

8 Botón de grabación (REC)– Púlselo para iniciar la

grabación manual.

Botón de grabación de un toque (OTR)– Activa

la grabación de un toque. (Sólo en el

televisor/videograbadora)

programa de temporizador.

Botón de reposición del contador (COUNTER

RESET)– Púlselo para reponer el contador a 0:00:00.

20 Botón de juego (GAME)– Establece el modo del

juego y el modo de entrada externa al mismo tiempo.

21 Botón de cámera lenta (SLOW)– Pulselo para

9 Indicador de grabación (RECORD)– Parpadea

durante la grabación.

activar la reproducción a cámera lenta.

22 Botón de pausa/imagen fija (PAUSE/STILL)–

Púlselo para detener temporalmente la cinta durante la

grabación o para ver una imagen fija durante la repro-

ducción.

Se enciende en el modo de espera de la grabación con

temporizador.

10 Ventanilla sensora del mando a distancia–

Recibe las señales infrarrojas procedentes del mando a

distancia.

11 Botones de canales (CHANNEL K/ L)– Púlselos

para seleccionar los canales deseados para ver o

grabar.

23 Botón de silenciamiento (MUTE)– Silencia el

sonido. Púlselo de nuevo para recuperar el sonido.

24 Botón de retorno de canal (CHANNEL

RETURN)– Púlselo para volver al canal anterior. Por

ejemplo, pulsando una vez este botón, la visualización

del canal cambiará de 3 (canal actual) a 10 (canal ante-

rior), y al pulsarlo por segunda vez, el canal cambiará

del 10 al 3.

25 Botón del temporizador despertador/para

dormir (WAKE-UP/SLEEP)– Ajusta el tempo-

rizador para despertarse/dormir.

Se puede mostrar el menú principal en la pantalla del

televisor pulsando repetidamente este botón del televi-

sor/videograbadora.

Función de seguimiento– Pulse los botones para

minimizar el ruido de vídeo (líneas o puntos en la pan-

talla) durante la reproducción.

12 Botones de volumen (VOLUME X / Y)– Ajustan

26 Cordón de alimentación– Conéctelo a la toma de

el nivel del volumen.

CA estándar (120V/60Hz).

13 Botón de la alimentación (POWER)– Púlselo

para encender y apagar el televisor/videograbadora.

Púlselo para activar la grabación con temporizador.

27 Terminal de antena (ANT.)– Para conectar una

antena o sistema de televisión por cable.

- 29 -

0I29

Download from Www.Somanuals.com. All Manuals Search And Download.

CONEXIONES DE ANTENA/CABLE

Desde el cable coaxial o

caja de emisiones vía

satélite de 75 ohm del

sistema de Cable

Caja de CATV

o caja de emi-

siones vía satélite

(no incluído)

Antena combinada de

VHF/UHF

(no incluído)

Antena de varilla UHF/VHF

(incluído)

OUT

Antena VHF

(no incluído)

Desde el

sistema de Cable

Antena UHF

(no incluído)

DC 13.2V

AC 120V

ANT.

Combinador de

VHF/UHF

(no incluído)

ANT.

Cable coaxial

de 75 ohm (no incluído)

PARA GRABAR UN CANAL

ANTENA COMBINADA DE VHF/UHF

La antena de varilla de VHF/UHF (incluído) es

desmontable. Inserte el vástago de la antena en el agujero

de la parte trasera superior del televisor/videograbadora.

Conecte la varilla de antena de VHF/UHF o la antena com-

binada de VHF/UHF al terminal ANT. del

televisor/videograbadora.

CODIFICADO/DESCODIFICADO

1. Ajuste el selector de canales del televisor/videograbado-

ra al canal de salida del convertidor de televisión por

cable o del convertidor de emisiones vía satélite. (Ej.:

CA3)

2. Seleccione el canal que desee grabar de su convertidor

de televisión por cable o del convertidor de emisiones

vía satélite.

ANTENAS SEPARADAS DE VHF/UHF

En algunos lugares será necesario utilizar una antena exte-

rior.

CONEXION MOVIL

CABLE SIN CONVERTIDOR/DESCODIFICADOR

ADVERTENCIA: El conductor nunca debe ver programas

del televisor o del videobgrabadora mientras está con-

duciendo un vehículo.

PRECAUCIÓN: Si usted usa la TV/VCR con el motor del

vehículo apagado, recargue la batería del vehículo aprox.

cada 4 horas de uso, para evitar que ésta se agote. Cuando

termine de usar la TV/VCR, siempre desenchufe el cordón

para la batería del automóvil del zócalo del encendedor de

cigarrillos.

Utilice esta conexión si su sistema de televisión por cable

se conecta directamente a su televisor/videograbadora sin

convertidor.Utilizando esta conexión usted podrá:

1)Utilizar el mando a distancia del televisor/videograbado-

ra para seleccionar canales.

2)Programar uno o más canales sin codificar para realizar

la grabación automática con temporizador.

1) La antena de interiores incluída es adecuada para usar cuando

el vehículo está inmóvil. Para obtener una mejor recepción en

ruta, utilice una antena de VHF/UHF para TV móvil de alta

calldad.

2) Enchufe el cordón para batería de automóvil al conector DC13.2V

(12V) en la parte posterior de la TV/VCR. Luego conecte el otro

extremo en el zócaio para el encendedor de cigarrillos del

automóvil.

NOTA: Con esta unidad SÓLO se podrá grabar y ver un

mismo canal al mismo tiempo.

CABLE CON CONVERTIDOR/DESCODIFICADOR

O CONVERTIDOR DE EMISIONES VÍA SATÉLITE

Si su servicio de televisión por cable le suministra un con-

vertidor, o si usted utiliza un sistema de emisiones vía

satélite, usted podrá utilizar las conexiones básicas.

NOTAS:

Utilizando estas conexiones, usted también podrá grabar

canales codificados. Sin embargo, la selección de los

canales deberá hacerse con el convertidor de televisión por

cable con el convertidor de emisiones vía satélite. Esto sig-

nifica que los canales no podrán ser cambiados con el

mando a distancia del televisor/videograbadora. La

grabación inatendida se limita a un canal cada vez.

Confirme que su vehículo tlene un sistema eléctrico a tierra

negativo de 13.2 (12) voltios.

•

Confirme que está usando sólo el cordón provisto para la

batería del automóvil. El uso de otro cordón puede dañar su

TV/VCR.

•

Asegúrese que no haya cenizas ni otro restos en el zócalo del

encendedor.

•

- 30 -

0I29

Download from Www.Somanuals.com. All Manuals Search And Download.

3) Seleccione “ENGLISH” o “ESPAÑOL” utilizando el

botón F.FWD/B o REW/s. “[ ]” indica el idioma

seleccionado.

4) Pulse el botón PLAY/K o STOP/L para señalar

“AUTOPRESELECCION”.

Luego pulse el botón F.FWD/B. El sintonizador explo-

rará y memorizará todos los canales activos de su área.

NOTAS:

Asegúrese de introducir completamente el enchufe del cordón de

la batería del automóvil en el zócalo del encendedor de cigarril-

los.

Siempre desenchufe primero del zócalo del encendedor de ciga-

rrillos el cordón para la batería del coche, antes de desconectar-

lo de la TV/VCR.

Antes de usar la alimentación de CA, usted debe desconectar de

la TV/VCR el cordón para la batería del atuomóvil.

•

Solamente reemplace un fusible por otro del mismo tipo 5A,

250V.

El televisor/videograbadora distingue entre los canales

de televisión estándar y los canales de televisor por

cable.

•

Al zócalo del encendedor

de cigarrillos el cordón

para la batería del coche

Si desea reproducir o grabar una cinta ANTES de prea-

justar el sintonizador, usted tendrá que pulsar el botón

MENU en el mando a distancia. Para preajustar de

nuevo el sintonizador, consulte “REPETICIÓN DE LA

PREPARACIÓN DE CANALES”.

•

Antena de VHF/UHF

para TV móvil

(no incluído)

La unidad de televisor/videograbadora puede reconocer

los canales de TV como ellos de TV por cable a causa

de los condiciones de recepción. En este caso, pruebe el

preajuste automático de nuevo en los condiciones finas

de recepción.

•

Cordón para la batería

del automóvil

5) El sintonizador se para en el canal memorizado más

bajo. Si desea recuperar canales seleccionados, usted

podrá seleccionar directamente el canal deseado con los

botones numerados del mando a distancia o con los

botones CHANNEL K o L.

DC 13.2V

AC 120V

DC13.2V

ANT.

MODO DE ENTRADA EXTERNA

AJUSTE DEL RELOJ

Cuando utilice una señal de entrada externa (otra

videograbadora o una videocámara), conecte los cables de

salida de audio/vídeo del equipo de reproducción a las

tomas AUDIO IN/VIDEO IN de su

televisor/videograbadora. Y luego pulse el botón CHAN-

NEL K o L hasta que “AUX” aparezca en la pantalla.

Cerciórese...

La alimentación del televisor/videograbadora deberá

•

estar conectada.

En el ejemplo de abajo, el reloj va a ajustarse así:

FECHA: 1 de mayo de 2001

HORA: 5:40 PM

Usted puede programar el temporizador para que explore

todos los canales que puedan recibirse en su zona.

1) Pulse el botón MENU en el mando a distancia.

Pulse el botón PLAY/K o STOP/L para indicar

“AJUSTE RELOJ”.

Luego, pulse el botón F.FWD/B.

2) Pulse el botón PLAY/K o STOP/L para indicar

“AJUSTE MANUAL RELOJ”.

Luego, pulse el botón F.FWD/B.

3) Pulse el botón PLAY/K o STOP/L hasta que aparezca

el mes deseado. (Ejemplo: Mayo - 05)

Luego, pulse el botón F.FWD/B.

4) Pulse el botón PLAY/K o STOP/L hasta que aparezca

el día del mes deseado. (Ejemplo: 1 - 01)

INSTALACIÓN DE LAS PILAS

1)Abra la tapa del compartimiento de las pilas del mando

a distancia presionándola en el sentido de la flecha.

2)Inserte 2 pilas tamaño “AA” en el compartimiento de las

pilas, en el sentido indicado por las marcas de polaridad

(+/-).

3)Vuelva a poner la tapa.

Luego, pulse el botón F.FWD/B.

5) Pulse el botón PLAY/K o STOP/L hasta que aparezca

el año deseado. (Ejemplo: 2001)

Luego, pulse el botón F.FWD/B.

6) Pulse el botón PLAY/K o STOP/L hasta que aparezca

la hora deseada. (Ejemplo: 5, PM)

Luego, pulse el botón F.FWD/B.

7) Pulse el botón PLAY/K o STOP/L hasta que aparezca

el minuto deseado. (Ejemplo: 40)

8) Pulse el botón MENU en el mando a distancia. Aunque

los segundos no se visualizan, éstos empiezan a contar

desde 00 cuando se pulsa MENU en el mando a distan-

cia. Utilice esta función para sincronizar el reloj con la

hora correcta.

PREPARACIÓN DE CANALES POR

PRIMERA VEZ

1) Enchufe el cable de alimentación del

televisor/videograbadora en una toma de CA estándar.

NOTA: Si aparezcan algunos digitos en el rincón de la

pantalla, pulse el botón POWER sin desenchufar el cable

de alimentación.

2) Pulse el botón POWER para encender el

televisor/videograbadora.

- 31 -

Download from Www.Somanuals.com. All Manuals Search And Download.

Sharp Projector XR 40X User Manual
Shure Microphone 545L User Manual
Sony Ericsson Bluetooth Headset HBH 608 User Manual
Sony Network Card MSAC PC3 User Manual
Sony Portable Radio ICF 1000L User Manual
Sony Universal Remote RM AV2500T User Manual
Sun Microsystems Computer Hardware CP2500 User Manual
Sunrise Medical Mobility Aid Quickie S 525 User Manual
SVA Security Camera CRR 1103 User Manual
Swann Security Camera SW244 X6C User Manual