Sylvania TV VCR Combo 6724DF User Manual

OWNER’S

MANUAL

COLOR TV/VCR/DVD TRIPLE COMBO

(24 inch)

6724DF

INSTRUCCIONES EN ESPAÑOL INCLUIDAS

If you need additional operating assistance after reading this owner’s

manual or to order replacement accessories, please call

TOLL FREE : 1-800-968-3429.

Or visit our WEB SITE at http://www.SylvaniaConsumerElectronics.com.

Please read before using this equipment

Download from Www.Somanuals.com. All Manuals Search And Download.

FIGURE A

EXAMPLE OF ANTENNA GROUNDING AS PER

NATIONAL ELECTRICAL CODE

ANTENNA

LEAD I N

WI RE

GROUND

CL AMP

ANTENNA

DISCHARGE UNIT

(NEC SECTION 810-20)

ELECTRI C

SERVICE

EQUIPMENT

GROUNDING CONDUCTORS

(NEC SECTION 810-21)

GROUND CLAMPS

NEC

NATIONAL ELECTRICAL CODE

POWER SERVICE GROUNDING

ELECTRODE SYSTEM

(NEC ART 250, PART H)

S2898A

13. Outdoor Antenna grounding - If an outside antenna or

cable system is connected to the unit, be sure the anten-

na or cable system is grounded so as to provide some

protection against voltage surges and built-up static

charges. Article 810 of the National Electrical Code,

ANSI/NFPA No. 70, provides information with respect

to proper grounding of the mast and supporting struc-

ture, grounding of the lead-in wire to an antenna dis-

charge unit, size of grounding conductors, location of

antenna-discharge unit, connection to grounding elec-

trodes, and requirements for the grounding electrode.

(Fig. A)

19. Damage Requiring Service - Unplug this unit from the

wall outlet and refer servicing to qualified service per-

sonnel under the following conditions:

a. When the power-supply cord or plug is damaged or frayed.

b. If liquid has been spilled, or objects have fallen into the

unit.

c. If the unit has been exposed to rain or water.

d. If the unit does not operate normally by following the

operating instructions. Adjust only those controls that are

covered by the operating instructions, as improper

adjustment of other controls may result in damage and

will often require extensive work by a qualified techni-

cian to restore the unit to its normal operation.

14. Lightning - For added protection for this unit receiver

during a lightning storm, or when it is left unattended

and unused for long periods of time, unplug it from the

wall outlet and disconnect the antenna or cable system.

This will prevent damage to the unit due to lightning and

power-line surges.

e. If the unit has been dropped or damaged in any way.

f. When the unit exhibits a distinct change in performance,

this indicates a need for service.

20. Replacement Parts - When replacement parts are

required, be sure the service technician has used replace-

ment parts specified by the manufacturer that have the

same characteristics as the original part. Unauthorized

substitutions may result in fire, electric shock, injury to

persons or other hazards.

15. Power Lines - An outside antenna system should not be

located in the vicinity of overhead power lines or other

electric light or power circuits, or where it can fall into

such power lines or circuits. When installing an outside

antenna system, extreme care should be taken to keep

from touching such power lines or circuits as contact

with them might be fatal.

21. Safety Check - Upon completion of any service or

repairs to this unit, ask the service technician to perform

routine safety checks to determine that the unit is in

proper operating condition.

16. Overloading - Do not overload wall outlets and exten-

sion cords as this can result in a risk of fire or electric

shock.

22. Heat - This unit product should be situated away from

heat sources such as radiators, heat registers, stoves, or

other products (including amplifiers) that produce heat.

17. Object and Liquid Entry - Never push objects of any

kind into this unit through openings as they may touch

dangerous voltage points or short out parts that could

result in a fire or electric shock. Never spill liquid of any

kind on the unit.

18. Servicing - Do not attempt to service this unit yourself

as opening or removing covers may expose you to dan-

gerous voltage or other hazards. Refer all servicing to

qualified service personnel.

- 3 -

Download from Www.Somanuals.com. All Manuals Search And Download.

PRECAUTIONS

LASER SAFETY

IMPORTANT COPYRIGHT INFORMATION

Unauthorized copying, broadcasting, public perfor-

mance and lending of discs are prohibited.

This product incorporates copyright protection tech-

nology that is protected by U.S. patents and other

intellectual property rights. Use of this copyright

protection technology must be authorized by

Macrovision, and is intended for home and other

limited viewing uses only unless otherwise autho-

rized by Macrovision. Reverse engineering or dis-

assembly is prohibited.

This unit employs a laser. Only a qualified service

person should remove the cover or attempt to ser-

vice this device, due to possible eye injury.

CAUTION: USE OF CONTROLS OR ADJUST-

MENTS OR PERFORMANCE OF PROCE-

DURES OTHER THAN THOSE SPECIFIED

HEREIN MAY RESULT IN HAZARDOUS

RADIATION EXPOSURE.

FCC WARNING- This equipment may gener-

ate or use radio frequency energy. Changes or

modifications to this equipment may cause

harmful interference unless the modifications

are expressly approved in the instruction man-

ual. The user could lose the authority to oper-

ate this equipment if an unauthorized change

or modification is made.

CAUTION: VISIBLE AND INVISIBLE LASER

RADIATION WHEN OPEN AND INTERLOCK

DEFEATED. DO NOT STARE INTO BEAM.

LOCATION: INSIDE, NEAR THE DECK

MECHANISM.

RADIO-TV INTERFERENCE

This Class B digital apparatus complies with

Canadian ICES-003.

This equipment has been tested and found to com-

ply with the limits for a Class B digital device, pur-

suant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against

harmful interference in a residential installation.

This equipment generates, uses, and can radiate

radio frequency energy and, if not installed and

used in accordance with the instructions, may cause

harmful interference to radio communications.

However, there is no guarantee that interference

will not occur in a particular installation. If this

equipment does cause harmful interference to

radio or television reception, which can be deter-

mined by turning the equipment off and on, the

user is encouraged to try to correct the interfer-

ence by one or more of the following measures:

1) Reorient or relocate the receiving antenna.

2) Increase the separation between the equipment

and receiver.

Cet appareil numérique de la classe B est

conforme à la norme NMB-003 du Canada.

CAUTION: TO PREVENT ELECTRIC SHOCK,

MATCH WIDE BLADE OF PLUG TO WIDE

SLOT, FULLY INSERT.

ATTENTION: POUR ÉVITER LES CHOC

ÉLECTRIQUES, INTRODUIRE LA LAME LA

PLUS LARGE DE LA FICHE DANS LA

BORNE CORRESPONDANTE DE LA PRISE

ET POUSSER JUSQU’AU FOND.

A NOTE ABOUT RECYCLING

Batteries should never be thrown away or inciner-

ated but disposed of in accordance with your local

regulations concerning chemical wastes.

3) Connect the equipment into an outlet on a cir-

cuit different from that to which the receiver is

connected.

4) Consult the dealer or an experienced radio/TV

technician for help.

The serial number of this product may be found on the back of the unit. No other unit has the same serial

number as yours. You should record the number and other vital information here and retain this book as a per-

manent record of your purchase to aid identification in case of theft. Serial numbers are not kept on file.

Date of Purchase

Dealer Purchase from

Dealer Address

Dealer Phone No.

Model No.

Serial No.

- 4 -

Download from Www.Somanuals.com. All Manuals Search And Download.

WARNING

LOCATION

Moisture condensation may occur inside the unit

when it is moved from a cold place to a warm place

or after heating a cold room or under conditions of

high humidity. If a DVD is played in a unit which has

moisture, it may damage the DVD and the unit.

Therefore when the condensation occurs inside the

unit, turn the unit on and allow at least 2 hours for the

unit to dry out.

For safe operation and satisfactory performance of

your unit, keep the following in mind when selecting

a place for its installation:

Shield it from direct sunlight and keep it away from

sources of intense heat.

•

Avoid dusty or humid places.

Avoid places with insufficient ventilation for proper

heat dissipation. Do not block the ventilation holes at

the top or bottom of the unit. Do not place the unit

on a carpet because this will block the ventilation

holes.

•

SYMBOLS USED IN THIS MANUAL

The following symbols below appear in some head-

ings and notes in this manual, with the following

meanings.

Install unit in a horizontal position.

Avoid locations subject to strong vibration.

Do not place the unit near strong magnetic fields.

Avoid moving the unit to locations where tempera-

ture differences are extreme.

Be sure to remove disc and unplug the AC power

cord from the outlet before carrying the unit.

•

TV/VCR

: Description refers to TV/VCR operation (in the

TV/VCR mode).

•

DVD-V

: Description refers to playback of DVD video discs

(in the DVD mode).

AVOID THE HAZARDS OF

ELECTRICAL SHOCK AND FIRE

: Description refers to playback of Audio CDs

(in the DVD mode).

Do not handle the power cord with wet hands.

•

Do not pull on the power cord when disconnecting

it from an AC wall outlet. Grasp it by the plug.

If by accident, water is spilled on your unit, unplug

the power cord immediately and take the unit to our

Authorized Service Center for servicing.

•

QUICK

: Description refers to the items to be set by the

QUICK mode (in the DVD mode).

•

Do not put your fingers or objects into the unit disc

loading tray.

•

Do not place anything directly on top of the unit.

•

SUPPLIED ACCESSORIES

Remote Control Unit

Batteries

Owner’s Manual

Owner's Manual

NE209UD

2 AA Batteries

1EMN21011

If you need to replace these accessories, please refer to the PART NO. under the illustrations and call our

help line mentioned on the front page.

Depending on your antenna system, you may need different types of Combiners (Mixer) or Separators

(Splitter). Contact your local electronics store for these items.

•

- 5 -

Download from Www.Somanuals.com. All Manuals Search And Download.

TABLE OF CONTENTS

C IMPORTANT SAFEGUARDS . . . . .2

C PLAYBACK . . . . . . . . . . . . . . . . . . .25

NORMAL PLAYBACK . . . . . . . . .25

TRACKING ADJUSTMENT . . . . .25

SLOW MOTION . . . . . . . . . . . . . .25

STILL PICTURE . . . . . . . . . . . . . .25

VERTICAL HOLD CONTROL . . .25

C SEARCH FUNCTION . . . . . . . . . . .38

TRACK SEARCH . . . . . . . . . . . . .38

TITLE / CHAPTER SEARCH . . . .38

TIME SEARCH . . . . . . . . . . . . . . .38

MARKER SETUP SCREEN . . . . . .38

C PRECAUTIONS . . . . . . . . . . . . . . . .4

LOCATION . . . . . . . . . . . . . . . . . . .5

AVOID THE HAZARDS OF

ELECTRICAL SHOCK AND FIRE .5

WARNING . . . . . . . . . . . . . . . . . . . .5

SPECIAL PLAYBACK FUNCTION . . .39

REPEAT . . . . . . . . . . . . . . . . . . . . .39

PROGRAM . . . . . . . . . . . . . . . . . . .39

RANDOM PLAYBACK . . . . . . . . .39

SYMBOLS USED IN THIS

MANUAL . . . . . . . . . . . . . . . . . . . . .5

C SPECIAL PLAYBACK . . . . . . . . . .26

RENTAL PLAYBACK . . . . . . . . . .26

AUTO REPEAT PLAYBACK . . . . .26

C SUPPLIED ACCESSORIES . . . . . . .5

C TABLE OF CONTENTS . . . . . . . . . .6

C FEATURES . . . . . . . . . . . . . . . . . . . .7

C SEARCH . . . . . . . . . . . . . . . . . . . . .27

ZERO RETURN . . . . . . . . . . . . . . .27

PICTURE SEARCH . . . . . . . . . . . .27

TIME SEARCH . . . . . . . . . . . . . . .27

INDEX SEARCH . . . . . . . . . . . . . .28

C CHANGING THE SETTINGS . . . .40

SUBTITLE LANGUAGE . . . . . . . .40

AUDIO LANGUAGE . . . . . . . . . . .40

STEREO SOUND MODE . . . . . . . .40

CAMERA ANGLE . . . . . . . . . . . . .41

BLACK LEVEL SETTING . . . . . . .41

VIRTUAL SURROUND . . . . . . . . .41

C OPERATING CONTROLS AND

FUNCTIONS . . . . . . . . . . . . . . . . . . .9

INSTALLING THE BATTERIES . .11

C SPECIAL FEATURES . . . . . . . . . .28

REAL TIME TAPE COUNTER . . .28

AUTO REWIND-EJECT . . . . . . . .28

C PREPARATION FOR USE . . . . . . .12

ANTENNA/CABLE

CONNECTION . . . . . . . . . . . . . . . .12

THE ON-SCREEN INFORMATION . .42

CONNECTING TO FRONT A/V

INPUT JACKS . . . . . . . . . . . . . . . .13

C RECORDING . . . . . . . . . . . . . . . . .29

C CHANGING THE DVD SET UP

ITEMS . . . . . . . . . . . . . . . . . . . . . . .43

NORMAL RECORDING . . . . . . . .29

CONNECTING TO A STEREO

AMPLIFIER EQUIPPED WITH DIGI-

TAL INPUT JACKS (for DVD) . . .13

CUSTOM MENU . . . . . . . . . . . . . .43

LANGUAGE SETTING . . . . . . .43

DISPLAY SETTING . . . . . . . . . .44

AUDIO SETTING . . . . . . . . . . .44

PARENTAL CONTROL . . . . . . .45

OTHER SETTINGS . . . . . . . . . .45

INITIALIZE . . . . . . . . . . . . . . . . . .45

SKIPPING UNWANTED SCENES

DURING RECORDING . . . . . . . . .29

OTR (One Touch Recording) . . . . . .30

CONNECTING TO A DOLBY

DIGITAL DECODER (for DVD) . .14

COPYING A VIDEO CASSETTE

(Requires a VCR or camcorder) . . .30

TV/VCR SECTION

C TIMER RECORDING . . . . . . . . . . .31

C TV OPERATION AND SETTINGS .15

WATCHING A TV PROGRAM . . .15

DEGAUSSING . . . . . . . . . . . . . . . .15

PICTURE CONTROL . . . . . . . . . . .15

SLEEP TIMER . . . . . . . . . . . . . . . .16

CLOSED CAPTION SYSTEM . . . .16

CHANNEL SET UP . . . . . . . . . . . .17

AUTOMATIC

TIMER RECORDING . . . . . . . . . .31

C TROUBLESHOOTING GUIDE . . .46

AUTO RETURN . . . . . . . . . . . . . . .33

C MAINTENANCE . . . . . . . . . . . . . . .49

C ON SCREEN DISPLAY . . . . . . . . .34

DISC HANDLING . . . . . . . . . . . . .49

C CABLE CHANNEL

DESIGNATIONS . . . . . . . . . . . . . .34

C SPECIFICATIONS . . . . . . . . . . . . .50

C ESPAÑOL . . . . . . . . . . . . . . . . . . . .51

C WARRANTY . . . . . . . . . . .Back Cover

DVD SECTION

CLOCK SET UP

(AUTO / MANUAL) . . . . . . . . . . . .18

C ABOUT THE DISCS . . . . . . . . . . . .35

PLAYABLE DISCS . . . . . . . . . . . .35

UNPLAYABLE DISCS . . . . . . . . . .35

DAYLIGHT-SAVING TIME . . . . . .19

V-CHIP SET UP . . . . . . . . . . . . . . .20

TV RATING SET UP . . . . . . . . .20

MPAA RATING SET UP . . . . . .21

CHANGE ACCESS CODE . . . . .21

MENU LANGUAGE . . . . . . . . . . .21

C PLAYING A DISC . . . . . . . . . . . . . .36

BASIC PLAYBACK . . . . . . . . . . . .36

GENERAL FEATURES . . . . . . . . .36

DISC MENU . . . . . . . . . . . . . . . . .36

TITLE MENU . . . . . . . . . . . . . . . . .36

RESUME . . . . . . . . . . . . . . . . . . . .37

PAUSE . . . . . . . . . . . . . . . . . . . . . .37

STEP BY STEP PLAYBACK . . . . .37

C MTS (Multi-Channel Television

sound) SYSTEM . . . . . . . . . . . . . . .22

CHECKING THE SELECTED

MTS MODE . . . . . . . . . . . . . . . . . .22

MTS RECORDING/MONITOR

MODE . . . . . . . . . . . . . . . . . . . . . .22

FAST FORWARD /

SELECTING THE MTS SYSTEM .23

FAST REVERSE . . . . . . . . . . . . . .37

SLOW FORWARD /

SLOW REVERSE . . . . . . . . . . . . . .37

C VIDEO CASSETTE . . . . . . . . . . . . .24

ZOOM . . . . . . . . . . . . . . . . . . . . . .37

- 6 -

Download from Www.Somanuals.com. All Manuals Search And Download.

FEATURES

TV/VCR Mode

¡Hi-Fi system

¡2 Step picture search operation

The Hi-Fi stereo recording system offers you

excellent sound quality with a dynamic range of

80dB, frequency response from 20Hz to 20kHz and

0.005% wow and flutter.

You can view a video program at a high speed or

super high speed in either a forward or reverse

direction in LP and SLP mode. For SP mode, only

high speed is available.

¡Rotary 4-head Record/Playback System

Four heads ensure excellent picture quality and

special effects playback.

¡Three different playback tape speeds : SP/LP/SLP

¡Two different recording tape speeds : SP/SLP

¡Auto Head Cleaner

¡Index Search

Fast-forwards to start of next recording.

Automatically cleans video heads as you insert or

remove a cassette.

¡Slow Motion

¡Zero Return

View recorded program at slower than normal

speed.

The tape returns to counter of 0:00:00 by rewind-

ing or fast forwarding.

¡Infrared remote control

¡Still

“Freeze” the picture at any time, for close viewing

of a particular scene.

¡Trilingual on screen TV/VCR setup display

selectable in English, Spanish or French

¡Real time counter

¡Digital Auto Tracking (DTR)

Automatically adjusts the tracking for each tape

you play.

This shows the elapsed recording or playback time

in hours, minutes and seconds. The “–” indication

will appear when the tape is rewound further than

the tape counter position “0:00:00”.

¡Rental play mode

Improves playback picture quality from worn

tapes, such as rental tapes.

¡181 channel capability PLL frequency synthesiz-

er tuner with direct station call

(A converter may be necessary to view scrambled

cable channels.)

¡Auto repeat

Allows you to repeat the playing of a tape indefi-

nitely without pressing [PLAY O].

¡Time search

Lets you set the unit to advance the tape by entering

the desired playback time you want to skip.

¡Auto Clock Setting

Allows you to set the clock function from a PBS

broadcast station.

¡Closed Caption Decoder

¡OTR (One Touch Recording)

Instant timed recording from 30 to 480 minutes is

possible by pressing [I REC/OTR].

¡1 Year, 8 events (including Daily and Weekly)

Timer Recording

The built-in timer allows you to record up to 8 pro-

grams at different times on different channels up to

1 year in advance. The Daily timer allows record-

ings to be made of daily broadcasts and the Weekly

timer allows recording to be made once a week up

to the end of the tape.

You may view specially labeled (cc) TV programs,

movies, news, prerecorded tapes, etc. with either a

dialogue caption or text display added to the pro-

gram.

¡V-CHIP

Enables parents to prevent their children from

watching inappropriate material on TV.

¡Auto power on and off system

Automatically turns on the unit when you insert the

cassette, turns off after auto-rewind and ejects

when the beginning of the tape is reached.

¡Auto return

¡Auto rewind when the end of a tape is reached

(This function doesn’t occur when using timer

recording.)

After timer recording is finished, the unit can

return to the beginning of the recording.

¡Sleep timer

¡Smooth mode change

TV/VCR mode and DVD mode automatically

changes without control.

Allows you to have the unit automatically turn off

at a desired time.

¡Timer Program Extension

Allows you to shift the time schedule for automatic

timer recording.

- 7 -

Download from Www.Somanuals.com. All Manuals Search And Download.

DVD Mode

¡Dolby Digital sound

¡On-screen display

This unit can handle Dolby Digital surround sound

having 5.1 channels when connected to a Dolby

Digital decoder.

Information about the current operation can be dis-

played on a TV screen, allowing you to confirm the

currently active functions (such as program play-

back), on the TV screen using the remote control.

¡Search

¡Still/fast/slow/step playback

Various playback modes are available including

still pictures, fast forward/reverse, slow motion and

step frames.

Chapter search / Title search / Track search / Time

¡Random playback for Audio CD

This unit can shuffle the order of tracks to play

them in random order.

¡Repeat

Chapter / Title / Track / All / A-B

¡Zoom

¡Program playback for Audio CD

You can program the order of tracks to play them in

any desired order.

¡DVD menus in a desired language

You can display DVD menus in a desired language,

if available on a DVD.

Magnified screen can be displayed.

¡Marker

The part designated by user can be called back.

¡Resume Play

User can resume to playback from the part at which

the play was stopped.

¡Screen saver/Auto power-off functions

The screen saver program starts when there is no

input from the unit for 5 minutes in the stop mode.

After the screen saver program is activated for 15

minutes, the power automatically turns off.

¡Subtitles in a desired language

¡Virtual Surround

¡Bit rate indication

¡DRC (Dynamic range control)

You can control the range of sound volume.

You can select a desired language for the display

subtitles, if that language is available on a disc.

¡Selecting a camera angle

You can select the desired camera angle, if a disc

contains sequences recorded from different angles.

¡Choices for audio language and sound mode

You can select the desired audio language and

sound mode, if different languages and modes are

available on a disc.

¡Parental lock

You can set the control level to limit playback of

discs which may not be suitable for children.

¡Automatic detection of discs

This unit automatically detects if the loaded disc is

DVD or Audio CD.

- 8 -

Download from Www.Somanuals.com. All Manuals Search And Download.

OPERATING CONTROLS AND FUNCTIONS

- FRONT PANEL - [Fig.1]

DVD buttons

TV/VCR buttons

REC/OTR REW PLAY F.FWD

–

POWER

VOLUME

SKIP

PLAY SKIP

STOP

OPEN/CLOSE

SELECT

CHANNEL

STOP

HEADPHONE VIDEO

AUDIO

EJECT

DVD

TV/VCR

4 3

8 9 10 11 12 13 14 4 15 16 17 18 19 20 21

5.C STOP Button [TV/VCR P.25 / DVD P.37]

(Front panel) Stops operation of the disc.

(Remote control) Stops operation of the disc or

tape contents.

[Fig. 2]

- REMOTE CONTROL -

6.A OPEN/CLOSE Button [DVD P.36]

Press to insert a disc into or remove it from the

tray.

7.Disc loading tray

8.DVD Indicator

Lights up during DVD mode.

POWER PICTURE SLEEP SELECT

CH.

PAUSE

+100

VOL.

9.SELECT Button [TV/VCR P.15] [DVD P.36]

Press to change to TV/VCR mode, external input

mode or DVD mode. You can see the mode

(TV/VCR or DVD) on the front panel indicator.

10. TV/VCR Indicator

+10

SPEED C.RESET

ZOOM

MUTE

(DVD) 3

PLAY

STOP

3 (DVD)

15 (TV/VCR)

^(TV/VCR)4¹⁴

Lights up during TV/VCR mode.

DISC

RECORD

11. CHANNEL (CH.) K / L Buttons

Press to select memorized channels.

DISPLAY

SETUP

ENTER

12. Recording Indicator

TITLE

RETURN

Flashes during recording. Lights up in the stand-

by mode for Timer Recording.

CLEAR SEARCH MODE REPEAT

A-B

13. REC/OTR Button (Front Panel) [TV/VCR P.30]

AUDIO SUBTITLE ANGLE

MODE

Press to start manual recording. Press repeatedly

to start One Touch Recording.

RECORD Button (Remote Control) [TV/VCR P.29]

Press to start manual recording.

14. E REW Button (for TV/VCR) [TV/VCR P.27]

Press to rewind the tape or to view the picture

rapidly in reverse during playback mode.

(Rewind Search)

15. F.FWD D Button (for TV/VCR) [TV/VCR P.27]

Press to rapidly advance the tape or to view the

picture rapidly in forward during playback mode.

(Forward Search)

1.POWER Button [TV/VCR P.15 / DVD P.36]

Press to turn the power on and off.

2.VOLUME (VOL.)

Buttons

Press to control the volume level for the DVD and TV.

3.SKIP H / G Buttons (for DVD) [DVD P.38]

Press once to skip chapters or tracks to a desired

point.

SEARCH E / D Buttons (for DVD) [DVD P.37]

Press and hold to change forward or reverse play-

back speed.

16. C / A STOP/EJECT Button [TV/VCR P.24, 27]

Press to stop the tape motion. Press in the stop

mode to remove tape from the unit.

17. Remote sensor window

18. HEADPHONE Jack

To connect headphone (not supplied) for personal

listening.

4.B PLAY Button [TV/VCR P.25 / DVD P.36]

Starts playback of the disc or tape contents.

- 9 -

Download from Www.Somanuals.com. All Manuals Search And Download.

- REAR PANEL - [Fig.3]

AUDIO OUT

COAXIAL

ANT.

19. VIDEO input Jack

31. MODE Button [DVD P.39, 41]

Connect to the video output jack of a video

camera or VCR.

Press to call up the program screen or the random

screen in the stop mode.

Press to call up the Black Level Setting screen or

the Virtual Surround screen during playback.

32. SEARCH MODE Button [DVD P.38]

Press to locate a desired point.

20. AUDIO L/R input Jacks

Connect to the audio output jacks of a video

camera or VCR.

21. Cassette compartment

33. AUDIO Button

22. PICTURE Button

TV/VCR Mode: [P.23]

Press to adjust the picture.

Press to select a desired sound mode when watch-

ing a TV program or playing or recording a cas-

sette tape.

DVD Mode: [P.40]

Press to select a desired audio language or sound

mode.

23. Number Buttons

TV/VCR Mode: [P.17]

Press two digits to directly access the desired

channel.

Remember to press [0] before a single digit channel.

+100 Button–

Press to select cable channels which are higher

than 99.

34. SUBTITLE Button [DVD P.40]

Press to select a desired subtitle language.

35. REPEAT Button [DVD P.39]

Repeats playback of the current disc, title, chapter,

or track.

DVD Mode: [P.38]

Press to enter the desired number.

+10 Button–

Press to enter the desired numbers which are high-

er than 9.

36. ANGLE Button [DVD P.41]

Press to change the camera angle to see the

sequence being played back from a different angle

(if available).

24. PAUSE F Button [TV/VCR P.25 / DVD P.37]

Pauses the current disc or tape operation.

37. A-B Button [DVD P.39]

25. SPEED Button [TV/VCR P.29]

Press to choose the desired recording speed:

SP/SLP.

Repeats playback of a selected section.

38. RETURN Button [TV/VCR P.32] [DVD P.38]

Returns to the previous screen in the setup menu.

26. C.RESET Button [TV/VCR P.27]

Press to reset counter to “0:00:00”.

Press to cancel a setting of timer program. (Refer

to page 32.)

{

39.

Buttons

TV/VCR Mode: [P.15]

Press to select a setting mode from the menu on

the TV screen.

Press to select or adjust from a particular menu.

DVD Mode: [P.36]

27. DISPLAY Button

TV/VCR Mode: [P.22]

Displays the counter or the current channel num-

ber and current time on the TV screen.

DVD Mode: [P.42]

Press to select a menu item.

40. ENTER Button [TV/VCR P.16] [DVD P.36]

Displays the current status on the TV screen.

Press to accept a setting.

28. SETUP Button [TV/VCR P.16] [DVD P.43-45]

41. DISC MENU Button [DVD P.36]

Press to enter or exit the setup menu of TV or DVD.

Calls up the DVD menu.

29. TITLE Button [DVD P.36]

42. ZOOM Button [DVD P.37]

Displays the title menu.

Enlarges part of a DVD-reproduced image.

30. CLEAR Button [DVD P.38]

Press to clear or cancel a setting currently entered.

- 10 -

Download from Www.Somanuals.com. All Manuals Search And Download.

43. MUTE Button [TV/VCR P.15]

46. Power cord [P.15]

Mutes the sound. Press it again to restore sound.

Connect to a standard AC outlet (120V/60Hz).

NOTE:

44. SLEEP Button [TV/VCR P.16]

Remove the power cord from the hook to

avoid breaking a wire before you connect to a

standard AC outlet.

•

Sets the Sleep Timer.

45. ANT. Jack [P.12]

Connect to an antenna, cable system or satellite

system.

47. AUDIO OUT COAXIAL Jack [P.13]

Connect to the digital input of an external

amplifier or decoder (for DVD Audio only).

NOTE:

We do not recommend the use of universal remote controls. Not all of the functions may be controlled with

a universal remote control.

•

If you decide to use a universal remote control with this unit, please be aware that the code number given

may not operate this unit. In this case, please call the manufacturer of the universal remote control.

INSTALLING THE BATTERIES

1)Open the battery compartment cover by pressing

the cover on the remote unit in the direction of the

arrow.

2)Insert 2 “AA” penlight batteries into the battery

compartment in the direction indicated by the

polarity (+/-) markings.

[BATTERY PRECAUTIONS]

Be sure to follow the correct polarity as indicated

in the battery compartment. Reversed batteries

may cause damage to the device.

•

Do not mix different types of batteries together

(e.g. Alkaline and Carbon-Zinc) or old batteries

with fresh ones.

•

3)Replace the cover.

If the device is not to be used for a long period of

time, remove the batteries to prevent damage or

injury from possible battery leakage.

•

Do not try to recharge batteries not intended to be

recharged; they can overheat and rupture.

•

- 11 -

Download from Www.Somanuals.com. All Manuals Search And Download.

PREPARATION FOR USE

ANTENNA/CABLE CONNECTIONS

Plug the incoming cable into the ANT. jack on the rear of the unit.

If your cable service supplies you with a converter box or if you use a satellite system, connect the box with this

unit as shown below.

Cable

TV signal

Antenna

Incoming cable from home Antenna /

Cable Company (No Cable Box)

AUDIO OUT

COAXIAL

ANT.

Rear of the unit

ANT.

Cable Box or

Satellite Box*

OUT

[Fig. 4]

Incoming cable from Cable Company

or Satellite Antenna

*NOTE (DO NOT DISCONNECT FROM BOX)

Some cable TV systems use scrambled signals and

require a special converter to receive these channels.

Consult your local cable company.

Note to CATV system installer:

This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that provides

guidelines for proper grounding and in particular, specifies that the cable ground shall be connected to the grounding

system of the building as close to the point of cable entry as practical.

Bent pin

NOTE:

Before plugging the antenna into the ANT. jack of the unit, check that the pin is

not bent. If it is bent, straighten the pin as illustrated, then plug the pin into the

ANT. jack of the unit.

Cable

Plug

(Needs to be

straightened)

(Straight pin)

For your safety and to avoid damages to the unit, unplug the antenna cable from the ANT. jack

before moving the unit.

- 12 -

Download from Www.Somanuals.com. All Manuals Search And Download.

CONNECTING TO FRONT A/V INPUT JACKS

When you watch a program recorded on another source (VCR or video camera), use the

AUDIO/VIDEO input jacks on the front of the unit.

AUX

Connect the Audio/Video output jacks of another source to the AUDIO L/R and VIDEO

jacks of this unit.

Then press [SELECT] or [CH.

] until “AUX” appears on the screen.

POWER

VOLUME

SKIP

PLAY SKIP

STOP

OPEN/CLOSE

SELECT

CHANNEL

REC/OTR

REW

PLAY F.FWD

STOP

HEADPHONE VIDEO

–

AUDIO

–

EJECT

DVD

TV/VCR

ex.

VCR or video camera, etc.

To the Audio output jacks

Audio Cable

(commercially available)

(IN)

(OUT)

–

HEADPHONE VIDEO

AUDIO

To the Video output jack

[Front of the unit]

Video Cable

(commercially available)

(IN)

[Fig. 5]

NOTE:

When you connect a monaural VCR (another source) to this unit, connect the Audio output jack of the

monaural VCR (another source) to the AUDIO L jack of this unit. The audio will output in both L and R

channel equally.

•

CONNECTING TO A STEREO AMPLIFIER EQUIPPED WITH

DIGITAL INPUT JACKS (for DVD)

Use an audio coaxial digital cable (commercially available) for the audio connections.

Connect to an amplifier equipped with digital input jacks such as MD Deck or DAT Deck.

(OUT)

AUDIO OUT

COAXIAL

ANT.

ex.

MD deck, DAT deck, etc.

To AUDIO OUT

COAXIAL jack

(Only DVD AUDIO OUT)

To Coaxial digital

Audio input jack

Audio coaxial digital cable

(commercially available)

(IN)

[Fig. 6]

NOTES:

The audio source on a disc in a 5.1 channel Dolby Digital surround format cannot be recorded as digital

sound by an MD or DAT deck.

•

Be sure to turn off the power to all components in the system before connecting another component.

Refer to the Owner’s Manuals for the components to be connected to the unit.

Set “DOLBY DIGITAL” to “PCM” for audio output in the setup mode. Playing a unit using incorrect set-

tings may generate noise distortion and may also damage the speakers. (Refer to page 44.)

•

- 13 -

Download from Www.Somanuals.com. All Manuals Search And Download.

CONNECTING TO A DOLBY DIGITAL DECODER (for DVD)

If using this unit to play a DVD disc in a 5.1 channel Dolby Digital surround format, the unit outputs a

DOLBY DIGITAL Data stream from its AUDIO OUT COAXIAL jack. By hooking the unit up to a Dolby

Digital decoder, you can enjoy a more convincing, realistic ambience with powerful and high-quality surround

sound as enjoyed in movie theaters.

Use an audio coaxial digital cable (commercially available) for the audio connections.

Center

speaker

(OUT)

Front speaker

(left)

Front speaker

(right)

AUDIO OUT

COAXIAL

ANT.

Dolby Digital

decoder

To AUDIO OUT

COAXIAL jack

(Only DVD AUDIO OUT)

To Coaxial digital

Audio input jack

Audio coaxial digital cable

(commercially available)

(IN)

Subwoofer

Surround

speaker

(left)

Surround

speaker

(right)

[Fig. 7]

NOTES:

Be sure to turn off the power to all components in the system before connecting another component.

Refer to the Owner’s Manuals for the components to be connected to the unit.

If connected to a Dolby Digital decoder, set “DOLBY DIGITAL” to “BITSTREAM” for audio output in the

setup mode. (Refer to page 44.)

•

Unless connected to a Dolby Digital decoder, set “DOLBY DIGITAL” to “PCM” for audio output in the

setup mode. Playing a unit using incorrect settings may generate noise distortion and may also damage the

speakers. (Refer to page 44.)

•

Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are

trademarks of Dolby Laboratories.

- 14 -

Download from Www.Somanuals.com. All Manuals Search And Download.

TV/VCR SECTION

TV OPERATION AND SETTINGS

WATCHING A TV PROGRAM

DEGAUSSING

TV/VCR

This television has a degaussing circuit that will clear

up color errors on the TV screen that are caused by

any excess magnetism which happens to get too close

to the TV. This circuit is designed to operate once

when the set is first plugged in. If minor color

errors are seen in some locations on the screen,

please unplug the TV for approximately 30 min-

utes. When the TV is plugged back in, the degauss-

ing circuit will operate once to clear them up. Repeat

this procedure any time the TV screen is accidentally

magnetized or when the TV is moved or relocated.

TV/VCR

1 Plug in the unit power cord

Plug the unit power cord into a standard

AC outlet.

NOTE:

If any digits appear in the corner of the

•

screen, press [POWER] without unplugging the

power cord.

2 Turn on the unit

Press [POWER] to turn on the unit.

PICTURE CONTROL

3 Select the channel number

TV/VCR

Use [CH.

] or the Number buttons to select

The unit’s picture controls – BRIGHT, CONTRAST,

COLOR, TINT and SHARPNESS – are preset to

factory specifications. Although they are usually the

best, you may need to make some further adjustments

for a more natural looking image.

your desired channel number.

Notes for using the Number buttons:

¡You must precede single-digit channel numbers

with a zero (for example: 02, 03, 04 and so on).

¡When selecting cable channels which are higher

than 99, press [+100] first, then press the last two

digits. (Example: to select channel 125, first press

[+100] then press [2] and [5].)

Make sure ...

The unit must be turned on.

•

1 Call up the menu

4 Adjust sound

Press [PICTURE].

Use [VOL.

] to adjust the

volume.

2 Select item you want to adjust

Use [K / L] until desired control is displayed.

Press [MUTE] to instantly mute

the sound. Press it again to restore

the previous sound level.

VOLUME 20

BRIGHT

CONTRAST

COLOR

TINT

SHARPNESS

NOTE:

If you use [CH.

] in the DVD mode, you can

•

BRIGHT

–

P +

change the TV channels. Even if you turn off the

unit in the DVD mode, when you turn it on again,

it will go into the TV/VCR mode.

3 Adjust the setting

Use

seconds.

[

to adjust to your desired level within 5

TO WATCH CABLE OR SATELLITE

CHANNEL

to decrease

brightness

to decrease

contrast

If the unit is connected to a cable box or satellite

•

BRIGHT

to increase

brightness

to increase

contrast

box, use [CH.

] to select CH3 or CH4

according to the output channel setting of the

device, and select desired channel on that device.

CONTRAST

TO WATCH EXTERNAL INPUT

COLOR

TINT

SHARPNESS to soft

to pale

to brilliant

When an external equipment is connected to the

•

to purple

to green

to clear

front AUDIO/VIDEO input jacks, press

[SELECT] or [CH.

] repeatedly until

“AUX” appears on the screen.

Even if there is a power failure of any kind, the

unit will retain its memory for this feature.

•

- 15 -

Download from Www.Somanuals.com. All Manuals Search And Download.

If the unit displays a black box

on the TV screen, this means that

the unit is set to the TEXT mode.

To clear screen, select [CAP-

TION1], [CAPTION2] or [OFF].

•

SLEEP TIMER

TV/VCR

The Sleep Timer function turns off the unit without

using [POWER] after a desired period of time.

Make sure ...

The unit must be turned on.

NOTE:

•

This function does not work during the record-

•

ing mode.

1 Select “CAPTION”

Press [SETUP].

Use [K / L] to point to

“CAPTION”.

- TV/VCR SETUP -

1 Call up the Sleep Timer Setting

TIMER PROGRAMMING

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

Press [SLEEP] so that “SLEEP 0 MINUTE” appears.

TIME SEARCH

INDEX SEARCH

2 Set sleep time

Press [SLEEP] repeatedly until

your desired sleep time appears.

Each additional press will increase

the time by 30 minutes up to 120

2 Select your desired caption mode

- TV/VCR SETUP -

Press [ENTER] repeatedly until

TIMER PROGRAMMING

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

your desired caption menu

appears.

([CAPTION1], [CAPTION2],

[TEXT1] or [TEXT2])

SLEEP 120 MINUTE

minutes.

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [CAPTION1]

ZERO RETURN

After 5 seconds, the Sleep Timer setting will disap-

pear automatically.

TIME SEARCH

INDEX SEARCH

TO CANCEL THE SLEEP TIMER

Press [SLEEP] to call up the Sleep Timer Setting.

Press [SLEEP] repeatedly until “SLEEP 0 MINUTE”

appears.

3 Exit the caption setting mode

Press [SETUP] to exit the menu.

NOTE:

Even if there is a power failure of any kind, the

unit will retain its memory for this feature.

•

CLOSED CAPTION SYSTEM

TV/VCR

TO CANCEL THE CLOSED CAPTION

SYSTEM

Repeat steps 1 to 2 and select [OFF] using [ENTER].

Then press [SETUP] to return to TV mode.

You can view specially labeled (cc) TV programs,

movies, news and pre-recorded tapes with either a

dialogue caption or text display.

CAPTION mode: You can watch dramas, movies and

news while captioning the dialogues and the contents

of news.

TEXT mode: You can watch half screen text informa-

tion if you want.

1-2: You may get these captions or text information

by selecting either “1” or “2”. Caption “2” is

usually used for a second language if available.

NOTES:

Not all programs are broadcast with closed cap-

•

tions. Your unit is designed to provide error free

closed captions from high quality antenna, cable

and VCR signals. Conversely, poor quality signals

are likely to result in caption errors or no captions

at all. Common signal conditions which may cause

caption errors are listed below:

Automobile ignition noise

Electric motor brush noise

Weak snowy reception on TV screen

Multiplex signal reception displaying picture

•

ghosts or airplane flutter.

Playback of poorly recorded or worn VCR tapes.

•

- 16 -

Download from Www.Somanuals.com. All Manuals Search And Download.

ADDING/DELETING CHANNELS

The channels you no longer receive or seldom watch

can be deleted from the memory. (Of course, you can

add the deleted channel into the memory again.)

CHANNEL SET UP

TV/VCR

Make sure ...

The unit must be turned on.

•

1 Select “CHANNEL SET UP”

- TV/VCR SETUP -

TIMER PROGRAMMING

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

AUTO CHANNEL PROGRAMMING

Press [SETUP].

Using [K / L] point to

“CHANNEL SET UP”, then press

[ENTER].

As the initial setting, this unit has memorized all

channels, including the ones not available in your

area. This feature automatically puts only available

channels into the memory.

TIME SEARCH

INDEX SEARCH

1 Select “CHANNEL SET UP”

2 Select “ADD/DELETE CH”

Using [K / L] point to

“ADD/DELETE CH”, then press

[ENTER].

- TV/VCR SETUP -

TIMER PROGRAMMING

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

– CHANNEL SET UP –

Press [SETUP].

ADD / DELETE CH (CATV)

AUTO CH PROGRAMMING

Using [K / L] point to

“CHANNEL SET UP”, then press

[ENTER].

TIME SEARCH

INDEX SEARCH

2 Begin channel scanning

Using [K / L] point to

3 Enter the desired channel number

– CHANNEL SET UP –

Use [CH.

] or the Number

ADD / DELETE CH (CATV)

AUTO CH PROGRAMMING

“AUTO CH PROGRAMMING”,

then press [ENTER].

buttons until your desired channel

number appears. (You can also use

[K / L] to enter it.)

The tuner scans and memorizes all

the active channels in your area.

ADD / DELETE

You must precede single-digit

•

channel numbers with a zero

(Example: 02 ... 09).

(Example: CH8)

3 After scanning

The tuner stops on the lowest memorized channel.

When selecting cable channels which are higher

than 99, press [+100] first, then press the last two

digits. (Example: to select channel 125, first press

[+100] then press [2] and [5].)

•

NOTES:

When “AUTO CH PROGRAM-

MING” is activated where there

•

NO TV SIGNALS

is no TV signal input, “NO TV

4 Delete (or add) it from (or into) memory

SIGNALS” will appear on the

display after the completion of

channel scanning.

Press [ENTER]. The channel number changes to

light red. The channel is deleted from memory.

To delete another channel, repeat steps 3 to 4.

If you press [ENTER] again, the channel is memo-

rized again.

•

The unit may recognize CATV channels to be TV

•

channels if reception condition is poor. In this case,

check the antenna connection and try “AUTO CH

PROGRAMMING” again when reception condi-

tions are better.

•

Added channel : Light blue

Deleted channel : Light red

Channel memory programming is NOT neces-

•

sary when connected to a cable box or satellite

box. Just select the channel for cable box or

satellite input (ex. CH3) on the unit, then select

your desired channel on the cable box or satel-

lite box.

5 Exit the channel setup mode

Press [SETUP] to exit the menu.

NOTE:

To confirm that channel(s) has been deleted or

•

added, use [CH.

- 17 -

Download from Www.Somanuals.com. All Manuals Search And Download.

CLOCK SET UP

5 Select the year

Use [K / L] until your desired

year appears.

(Example: “2005”)

Then press [B].

(AUTO / MANUAL)

– MANUAL CLOCK SET –

MONTH DAY

YEAR

2 0 0 5

TV/VCR

0 5

0 6 FRI

The unit clock must be set correctly so that VCR

timer recording is possible. It is suggested that the

clock be set manually when first setting up the unit,

then set to [ON] the auto clock setting which will

periodically correct the setting if necessary.

HOUR

– –

MINUTE

– – – –

6 Select the hour

Use [K / L] until your desired

hour appears.

(Example: “5”, “PM”)

Then press [B].

– MANUAL CLOCK SET –

NOTE:

•

MONTH DAY

YEAR

2 0 0 5

If you cannot receive a station with time signals,

auto clock setting cannot be performed. Use manu-

al setting only.

0 5

0 6 FRI

HOUR

0 5

MINUTE

– – PM

MANUAL CLOCK SETTING

Make sure ...

7 Select the minute

Use [K / L] until the desired

minute appears.

– MANUAL CLOCK SET –

MONTH DAY YEAR

The unit must be turned on.

In the example below, the clock is to be set to:

•

0 5

0 6 FRI

2 0 0 5

(Example: “40”)

HOUR

0 5

MINUTE

4 0 PM

DATE

May 6th, 2005

SETTING TIME

5:40PM

8 Start the clock

1 Select “SETTING CLOCK”

Press [SETUP].

Using [K / L] point to

“SETTING CLOCK”, then press

[ENTER].

- TV/VCR SETUP -

Press [SETUP].

TIMER PROGRAMMING

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

5:40 PM

Although seconds are not displayed,

they begin counting from 00 when

you press [SETUP]. Use this fea-

ture to synchronize the clock with

the correct time.

TIME SEARCH

INDEX SEARCH

NOTE:

2 Select “MANUAL CLOCK SET”

Using [K / L] point to

When unplugging the AC cord or if there is a

– SETTING CLOCK –

•

AUTO CLOCK

[ON]

power failure for more than 3 seconds, you may

have to reset the clock.

“MANUAL CLOCK SET”, then

press [ENTER].

AUTO CLOCK CH SEARCH

AUTO CLOCK CH

MANUAL CLOCK SET

D.S.T.

[ 02 ]

[OFF]

TO CHANGE CLOCK SETTING

If you want to change the clock,

1)Follow steps 1 to 2.

2)Select the item you want to change using [B] .

3)Enter correct numbers using [K / L].

4)Press [SETUP] to start the clock.

If there is no local PBS station in your area or on

your cable system, select “AUTO CLOCK” and

press [ENTER] to turn [OFF] this function before

this step.

•

3 Select the month

Use [K / L] until your desired

month appears.

– MANUAL CLOCK SET –

MONTH DAY YEAR

0 5

– – – – – – – – –

(Example: May → “05”)

Then press [B]. (Or press [s] to

go back one step.)

HOUR

– –

MINUTE

– – – –

4 Select the day

Use [K / L] until your desired day

appears.

– MANUAL CLOCK SET –

MONTH DAY YEAR

0 5

0 6 – – – – – – –

(Example: 6th → “06”)

Then press [B].

HOUR

– –

MINUTE

– – – –

- 18 -

Download from Www.Somanuals.com. All Manuals Search And Download.

AUTOMATIC CLOCK SETTING

Make sure ...

4 Enter the channel number that contains the

The unit must be turned on.

Confirm the unit is receiving a RF (Radio

Frequency) signal from either an antenna or cable

system connection using the ANT. jack on the rear

of the unit.

•

Automatic Clock Setting Signal

Press [RETURN] to go back to

– SETTING CLOCK –

AUTO CLOCK

[ON]

“SETTING CLOCK” menu.

Press [L] to select

AUTO CLOCK CH SEARCH

AUTO CLOCK CH

MANUAL CLOCK SET

D.S.T.

[

45]

“AUTO CLOCK CH”.

Use [s / B] until you locate Auto

NOTES:

[OFF]

If a cable converter box is being used, make sure it

is powered on.

•

Clock Set station number.

You must use the remote control to perform the

clock setting procedure.

If the unit is connected directly to a cable converter

box or satellite box, the local PBS station must be

^{selected on the cable box itself and the unit must be}•

set to the output channel of the cable converter box

or satellite box (usually channel 3 or 4), to be able

to set up or correct the clock automatically.

•

5 Exit the setting clock mode

Press [SETUP] to exit the menu.

•

NOTE:

Once the unit is turned off, it will periodically

check and set the correct date and time.

DAYLIGHT-SAVING TIME

1 Select “SETTING CLOCK”

TV/VCR

Select this feature and the unit’s clock automatically

will advance one hour in April, then reverse one hour

in October.

When Daylight-Saving Time is ON, the clock will

change automatically as follows:

- TV/VCR SETUP -

TIMER PROGRAMMING

Press [SETUP].

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

Using [K / L] select

“SETTING CLOCK”, then press

[ENTER] .

TIME SEARCH

INDEX SEARCH

First Sunday of April : At 2 AM the clock immedi-

•

2 Set “AUTO CLOCK” to [ON]

Press [ENTER] to select [ON].

– SETTING CLOCK –

ately changes to 3 AM. Any timer programming

you have set to occur between 2 AM and 3 AM will

not record.

Last Sunday of October : At 2 AM the clock

immediately changes to 1 AM.

AUTO CLOCK

[ON]

AUTO CLOCK CH SEARCH

AUTO CLOCK CH

MANUAL CLOCK SET

D.S.T.

[ 02 ]

•

[OFF]

Make sure ...

3 Begin “AUTO CLOCK CH SEARCH”

The unit must be turned on.

•

– SETTING CLOCK –

Press [L] to select

AUTO CLOCK

[ON]

“AUTO CLOCK CH SEARCH”.

Then press [ENTER].

The unit begins searching for the

AUTO CLOCK CH SEARCH

1 Select “SETTING CLOCK”

Press [SETUP].

Using [K / L] point to

“SETTING CLOCK”, then press

[ENTER].

AUTO CLOCK CH

MANUAL CLOCK SET

D.S.T.

[ 02 ]

- TV/VCR SETUP -

TIMER PROGRAMMING

•

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

[OFF]

station which contains the auto

clock set signal. The search for a

signal may take up to 20 seconds

per channel.

– AUTO CLOCK CH SEARCH –

TIME SEARCH

INDEX SEARCH

When the search has ended, “_ _”

appears at the lower left of the

screen.

Write down the number(s) that appear on the

screen. They are the auto clock station(s) in your

area.

If no number appears on the TV screen, there are

no stations in your area which contain the Auto

Clock signal. Auto Clock Setting is not possible.

Please use Manual Clock Setting on page 18.

•

2 Set “D.S.T.” (Daylight-Saving Time) to [ON]

_ _

Using [K / L] point to “D.S.T.”,

– SETTING CLOCK –

AUTO CLOCK

[ON]

then press [ENTER] until [ON]

appears.

•

AUTO CLOCK CH SEARCH

AUTO CLOCK CH

MANUAL CLOCK SET

D.S.T.

[ 02 ]

[ON]

3 Exit the Daylight-Saving Time mode

Press [SETUP] to exit the menu.

NOTE:

During AUTO CLOCK CH SEARCH, the picture

may be distorted.

TO CANCEL THE DAYLIGHT-SAVING

TIME

Repeat steps 1 to 2 and select [OFF] using [ENTER].

•

- 19 -

Download from Www.Somanuals.com. All Manuals Search And Download.

NOTES:

V-CHIP SET UP

When you select a rating and set

•

it to [BLOCK], the higher ratings

will be blocked automatically.

The lower ratings will be avail-

able for viewing.

TV–Y

TV–Y7

TV–G

TV–PG (DLSV)

TV–14 (DLSV)

TV–MA ( LSV)

[VIEW]

TV/VCR

(

)

[VIEW]

[BLOCK]

This feature enables parents to prevent their children

from watching inappropriate material on TV. When

you try to access a program which is blocked,

“PROTECTED PROGRAM by ...” message appears

on the TV screen.

When you set the lowest rating to

[VIEW], all other ratings will automatically be

available for viewing.

•

V-CHIP SET UP

5 Setting “Sub-Ratings”

Make sure ...

TV–Y

[VIEW]

When you select the ratings of TV-

TV–Y7

TV–G

(

)

The unit must be turned on.

•

Y7, TV-PG, TV-14 or TV-MA you

will have the option of setting sub

rating categories.

Using [K / L] select a rating with

sub-ratings you wish to block, then

press [ENTER] twice.

Using [K / L] select a sub-rating,

then press [ENTER] to set it to

[BLOCK] or [VIEW].

TV–PG (

)

TV–14

(

TV–MA(

1 Select “V-CHIP SET UP”

- TV/VCR SETUP -

TIMER PROGRAMMING

Press [SETUP].

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

TV–Y7

[BLOCK]

Using [K / L] select “V-CHIP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

SET UP”, then press [ENTER].

INDEX SEARCH

2 Enter Access code

Use the Number buttons to enter

the access code.

TV–PG

[BLOCK]

ACCESS CODE

[BLOCK]

For the first time set-up or in the

event the unit has lost power,

enter the default code of 0000.

•

Selection

TV-Y7

Rating Category Explanations

3 Select the desired item

Fantasy Violence

Using [K / L] select “TV RATING”, “MPAA RAT-

ING” or “CHANGE CODE”, then press [ENTER].

Refer to the pages below to set up each item.

TV-PG, TV-14, TV-MA

Suggestive Dialog (TV-PG, TV-14 only)

Coarse Language

Sexual Situation

Violence

– V-CHIP SET UP –

P 20 Step

B TV RATING

MPAA RATING

CHANGE CODE

P 21 Step

NOTE:

The blocked sub-ratings will

appear next to the rating catego-

ry in the “TV RATING” menu.

P 21 Step

•

TV–Y

TV–Y7

TV–G

TV–PG (DLSV)

TV–14 (DLSV)

TV–MA ( LSV)

[VIEW]

(

)

[VIEW]

[BLOCK]

A ^{TV RATING SET UP}

Follow steps to in the “V-CHIP SET UP” section

above.

6 Exit the V-Chip setting mode

Press [SETUP] to exit the menu.

4 Blocking TV programs

Using [K / L] select a rating that

you wish to block.

Press [ENTER] repeatedly to set it

to [BLOCK] or [VIEW].

NOTE:

To change the rating, the TV

TV–Y

TV–Y7

TV–G

TV–PG (

TV–14

TV–MA(

[VIEW]

(

)

•

)

PROTECTED PROGRAM

by TV-Y

(

must be turned to an unprotected

program. If “PROTECTED

PROGRAM by ...” appears on

the screen, please change the

channel to a station that is not

protected.

Selection

TV-Y

TV-Y7

TV-G

Rating Category Explanations

Appropriate for all children

Appropriate for children seven and older

General Audience

TV-PG

TV-14

Parental Guidance suggested

Unsuitable for children under 14

TV-MA Mature audience only

- 20 -

Download from Www.Somanuals.com. All Manuals Search And Download.

MENU LANGUAGE

MPAA RATING SET UP

TV/VCR

Follow steps to in the “V-CHIP SET UP” section

on page 20.

1 Select “LANGUAGE”

Press [SETUP].

Use [K / L] to point to

“LANGUAGE”.

- TV/VCR SETUP -

4 Select your desired item

Using [K / L] point to your desired

item, then press [ENTER] to select

[BLOCK] or [VIEW].

TIMER PROGRAMMING

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

[VIEW]

PG–13

NC–17

[VIEW]

[BLOCK]

TIME SEARCH

INDEX SEARCH

Selection

PG-13

Rating Category Explanations

General Audience

Parental Guidance suggested.

Unsuitable for children under 13

Restricted; under 17 requires accompa-

nying parent or adult guardian

No one under 17 admitted

2 Select “ENGLISH”, “ESPAÑOL” or “FRANÇAIS”

Press [ENTER] repeatedly to select “ENGLISH”,

“ESPAÑOL”= Spanish or “FRANÇAIS”= French.

3 Exit the Language mode

Press [SETUP] to exit the menu.

NC-17

Mature audience only

NOTES:

This function effects only the language on the

•

When you select a rating and set it to [BLOCK],

the higher ratings will be blocked automatically.

The lower ratings will be available for viewing.

When you set the lowest rating to [VIEW], all

other ratings will automatically be available for

viewing.

•

screen menu and not the audio source.

If for some reason the menu is in Spanish or

French, press [SETUP], [K / L] to point to

“IDIOMA [ESPAÑOL]” or “LANGAGE

[FRANÇAIS]”, then press [ENTER] repeatedly to

select desired language, then press [SETUP].

•

5 Exit the V-Chip setting mode

Press [SETUP] to exit the menu.

CHANGE ACCESS CODE

Follow steps to in the “V-CHIP SET UP” section

on page 20.

4 Enter New code

Use the Number buttons to enter

your desired access code in the

“NEW CODE” space, then enter

the same code in the “CONFIRM

CODE” space. When completed,

the menu will return to “V-CHIP

SET UP”.

NEW CODE

X X X X

CONFIRM CODE

Make sure you enter exactly the same new code in

the “CONFIRM CODE” space as one in the

“NEW CODE” space. If they are different, the

“NEW CODE” space is cleared for redoing.

•

5 Exit the V-Chip setting mode

Press [SETUP] to exit the menu.

NOTE:

Your personal access code will be erased and will

•

return to the default (0000) when a power failure

occurs or when you turn off the power using a

wall switch. If you have forgotten the code, unplug

the power cord for 10 seconds to restore the access

code to 0000.

- 21 -

Download from Www.Somanuals.com. All Manuals Search And Download.

MTS (Multi-Channel Television sound) SYSTEM

This unit have a feature that allows for reception of sound other than the main audio program.

This feature is called Multi-channel Television Sound (MTS). You can listen or record mono audio sound,

stereo sound, or Secondary Audio Program (SAP).

CHECKING THE SELECTED MTS MODE

TV/VCR

By pressing [DISPLAY], the status shown below

will appear on the display when you play a VHS

tape or receive a broadcast on the unit tuner channel

you are watching.

1) When a program is broadcast in stereo,

“STEREO” appears on the TV screen.

2) When a program is broadcast in second audio,

“SAP” appears on the TV screen.

3) When a program broadcast both in stereo and sec-

ond audio, “STEREO” and “SAP” appear on the

TV screen.

PLAY

HIFI

12:00AM

CH 123

STEREO/SAP

NOTE:

Although a program may be broadcast in both

•

stereo and second audio, you cannot record in

both stereo and second audio at the same time.

4) While the unit is set in HIFI stereo mode and

playback mode, “HIFI” appears on the TV screen.

While the unit is set in monaural (“MONO”)

mode, “HIFI” disappears from the TV screen.

NOTE:

COUNT

0:00:00

Second Audio Program, which means your

program, can also be received in a second

language or sometimes a radio station.

SAP

High Fidelity which produces better sound

than standard stereo units.

HIFI

If you play non-HIFI tapes while the unit is set

•

in “HIFI”, “HIFI” will disappear from the TV

screen and the unit will play automatically in

monaural.

MTS RECORDING/MONITOR MODE

TV/VCR

Type of broadcast Display on

STEREO/SAP

Hi-Fi audio track (2-channel) Normal audio

the TV screen SELECTION

L-channel

R-channel

track

Regular

-None-

-Invalid-

Mono

(monaural audio)

Stereo broadcast

Bilingual broadcast

STEREO

SAP

-Invalid-

STEREO*

L+R

Main audio

program

Main audio

program

Main audio

program

SAP*

Sub audio

program

Sub audio

program

Sub audio

program

Stereo & Bilingual

broadcast

STEREO

SAP

STEREO*

SAP*

L+R

Sub audio

program

Sub audio

program

Sub audio

program

*You must select the recording mode in TV AUDIO [STEREO] or [SAP] when you record a broadcast.

- 22 -

Download from Www.Somanuals.com. All Manuals Search And Download.

SELECTING THE MTS SYSTEM

TV/VCR

You can select the MTS output mode for recording or

watching the program, also the audio output mode

for playing cassettes.

WHEN IN THE EXTERNAL INPUT

MODE (“AUX”)

Pressing [AUDIO] does not affect the audio output

mode and the current audio output mode does not

appear on the TV screen.

WHEN RECEIVING AN MTS BROADCAST

Press [AUDIO] repeatedly to select the MTS output

mode.

The output mode changes as described below every

time you press the button.

•

STEREO

SAP

MONO

The current mode appears on the TV screen for

about 5 seconds.

•

NOTES:

The initial setting is “STEREO”. The unit records

automatically MTS broadcasts in HIFI stereo sound

unless you select SAP mode recording beforehand.

•

This setting is saved even if the unit is turned off

or the AC cord is unplugged.

•

If you select second audio when second audio is

not available, the unit will record normal audio.

•

WHEN PLAYING CASSETTES

Press [AUDIO] to select “HIFI” or “MONO”.

The current mode appears on the TV screen for

about 5 seconds.

•

The initial setting is “HIFI”.

This setting is saved until the cassette is ejected.

•

NOTES:

Normally “HIFI” should be selected for playback

with HIFI sound.

•

When you play non-HIFI tapes, the unit will play

only in the monaural mode even if you set HIFI.

•

- 23 -

Download from Www.Somanuals.com. All Manuals Search And Download.

VIDEO CASSETTE

This unit will operate with any cassette that has the

mark. For best results, we recommend the use of

high-quality tapes. Do not use poor quality or damaged tapes.

PRECAUTIONS

INSERTING A CASSETTE

Avoid moisture. Moisture condensation may occur

Insert the cassette in the direction as shown. Push in

gently, but continuously, on the center-back of the

cassette until it is drawn into the unit. The unit will

automatically turn on.

•

on the tape if it is moved from a cold place to a

warm place or vice versa. Before using a tape with

these conditions, to avoid damage of the tape and

your unit, wait until the tape has warmed to room

temperature and the moisture has evaporated.

Avoid extreme heat, high humidity and magnetic

fields.

•

Window

Do not tamper with the cassette mechanism.

Do not touch the tape with your fingers.

•

WRONG

CORRECT

TWO DIFFERENT TAPE SPEEDS

REMOVING A CASSETTE

Before recording, select the tape speed from : SP

mode (Standard Play) or SLP mode (Super Long

Play).

The table below shows the maximum recording/play-

back time using T60, T120 or T160 tapes in each

mode.

1)In the stop mode, press [C / A STOP/EJECT] on

the unit. The cassette will be ejected.

2)Pull the cassette out of the cassette compartment.

3)Store the cassette in its case as shown.

Tape Speed

Type of tape

SP mode

Recording/Playback Time

T60

1 hour

3 hours

T120

T160

2 hours 2-2/3 hours

6 hours 8 hours

SLP mode

ERASE PREVENTION

NOTE:

You can play back a tape recorded in LP mode

(Long Play).

•

You can prevent accidental

erasing of recording by

breaking off the tab on the

back edge of the cassette.

Tab

If you decide to record on

the tape again, cover the

hole with plastic tape.

Plastic Tape

NOTE:

In DVD mode, whether the cassette is with tab or

without tab you insert, it doesn’t start playing until

•

[B PLAY]

you press

In TV/VCR mode, if the cassette without tab is

inserted, playback will start automatically.

- 24 -

Download from Www.Somanuals.com. All Manuals Search And Download.

PLAYBACK

NORMAL PLAYBACK

SLOW MOTION

TV/VCR

Press [PAUSE F], then press [D] to start the play-

back in slow motion. The unit mutes the sound dur-

ing slow motion. Press [PLAY O] to return to nor-

mal playback.

Make sure ...

The unit must be turned on.

•

1 Insert a prerecorded tape

NOTE:

If the erase-prevention tab has been removed, the

unit will start playback automatically.

If it is left in the slow mode for more than 5 min-

•

utes, the unit will automatically go into the stop

mode.

PLAY

2 To begin playback

Press [PLAY O].

STILL PICTURE

TV/VCR

You can view a still picture on the TV screen during

playback (the still mode). Press [PAUSE F] during

playback. Only tapes recorded in the SLP mode will

show the least amount of lines. Press [PLAY O] to

return to playback.

3 To stop playback

Press [STOP C].

STOP

NOTES:

You can advance the picture one frame at a time by

pressing [PAUSE F] during the still mode.

If it is left in the pause mode for more than 5 min-

utes, the unit will automatically switch to the stop

mode.

•

NOTES:

Even in the DVD mode, you can start the VCR

playback if you press [ PLAY] (of the TV/VCR

side).

•

VCR playback will stop and the mode will change

to the DVD mode by pressing [SELECT],

•

[

PLAY] (DVD side) or [ OPEN/CLOSE].

VERTICAL HOLD CONTROL

TV/VCR

In the pause/still mode only, when the picture begins

to vibrate vertically, stabilize the picture by using

TRACKING ADJUSTMENT

[CH.

TV/VCR

NOTE:

Tracking adjustment will be set automatically

(Digital Tracking function) when you start play-

back.

•

If there are video noise lines on the screen, refer to

TRACKING ADJUSTMENT on this page.

•

Noise lines (black and white streaks) may appear

on the playback picture when playing pre-recorded

tapes or tapes recorded on other VCR. If this

occurs, use [CH.

] until the streaks disappear.

You can reduce the noise lines by using

•

[CH.

] in the slow mode too. Tracking

adjustment in the slow mode will not be set auto-

matically.

To return to the Digital Auto Tracking function,

stop the tape once and start playback.

- 25 -

Download from Www.Somanuals.com. All Manuals Search And Download.

SPECIAL PLAYBACK

Make sure ...

AUTO REPEAT PLAYBACK

The unit must be turned on.

•

Insert a prerecorded tape.

•

TV/VCR

The unit has the auto repeat function that allows you to

repeat a tape indefinitely without pressing [PLAY O].

ALL REPEAT: Repeat playback from the beginning

to the end of the tape.

BLANK REPEAT: Repeat playback from the begin-

ning to a blank part, which is blank for more than

10 seconds.

RENTAL PLAYBACK

TV/VCR

This function enables you to improve the picture

quality when playing back worn cassettes such as

rented tapes.

1 Select “USER’S SET UP”

- TV/VCR SETUP -

1 Select “USER’S SET UP”

- TV/VCR SETUP -

TIMER PROGRAMMING

Press [SETUP].

SETTING CLOCK

TIMER PROGRAMMING

CHANNEL SET UP

SETTING CLOCK

Press [SETUP].

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

Using [K / L] point to “USER’S

SET UP”, then press [ENTER].

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

Using [K / L] point to “USER’S

SET UP”, then press [ENTER].

INDEX SEARCH

2 Set “RENTAL” to [ON]

Using [K / L] point to “RENTAL”.

Press [ENTER] until [ON]

appears.

USER’S SET UP

–

2 Select “ALL” or “BLANK”

Using [K / L] point to

USER’S SET UP

–

RENTAL

[ON]

[OFF]

REPEAT PLAY

AUTO RETURN

“REPEAT PLAY”.

RENTAL

[OFF]

[ALL]

[OFF]

REPEAT PLAY

AUTO RETURN

Press [ENTER] repeatedly until

your desired selection [ALL] or

[BLANK] appears.

3 Exit the Rental setting

Press [SETUP] to return to the TV mode.

3 Exit the Repeat Play setting

Press [SETUP] to return to the TV mode.

4 Start playback

Press [PLAY O] to start playback.

“RENTAL PLAY B” appears.

•

Press [PLAY O] to start the Repeat Play.

“REPEAT PLAY B” appears.

•

Once you select the rental mode, it stays in effect

even after you turn off the unit.

Once you select the repeat play mode, it stays in

effect even after you turn off the unit.

If the rental mode is set [ON], the “RENTAL

PLAY B” display has priority.

•

TO CANCEL THE RENTAL MODE

Repeat steps 1 to 2 and select [OFF] using

[ENTER]. Press [SETUP] to return to TV mode.

Even if there is a power failure of any kind, the

unit will retain its memory for this feature.

TO CANCEL THE REPEAT PLAY MODE

Repeat steps 1 to 2 and select [OFF] using [ENTER].

Press [SETUP] to return to TV mode.

Even if there is a power failure of any kind, the

unit will retain its memory for this feature.

- 26 -

Download from Www.Somanuals.com. All Manuals Search And Download.

Make sure ...

NOTE:

Tapes recorded in SP or LP mode will normally

•

The unit must be turned on.

•

display a noise bar on the TV screen and the pic-

ture may revert to Black and White.

Insert a tape.

•

ZERO RETURN

3 Return to normal speed

Press [PLAY O].

TV/VCR

This function allows you to search easily a beginning

point that you want to review by rewinding or fast

forwarding.

TIME SEARCH

NOTE:

Zero Return WILL NOT work on a blank tape or

a blank portion of a tape.

TV/VCR

•

The Time Search function makes it possible to quick-

ly advance the tape to your desired position simply

by entering the exact amount of playback time you

want to skip.

1 Stop a tape at your desired point

Rewind or fast forward the tape to the beginning

point at which you want to review.

NOTE:

•

Time Search can be set up to a maximum of 9

hours 50 minutes (9:50) by 10 minutes at a time.

2 Reset the counter to 0:00:00

Press [C.RESET] repeatedly.

In the example below:

To watch a program before/ after 2 hour 50 minutes

from the present position, in either direction.

3 Begin recording or playback

Press [RECORD] or [PLAY O].

Press [STOP C] when recording or playback is com-

pleted.

1 Select “TIME SEARCH”

- TV/VCR SETUP -

TIMER PROGRAMMING

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

Press [SETUP].

Using [K / L] point to “TIME

CAPTION [OFF]

SEARCH”, then press [ENTER].

ZERO RETURN

4 To activate “ZERO RETURN”

TIME SEARCH

INDEX SEARCH

- TV/VCR SETUP -

Press [SETUP].

TIMER PROGRAMMING

SETTING CLOCK

CHANNEL SET UP

Using [K / L] point to “ZERO

RETURN”, then press [ENTER].

The unit will begin rewinding and

the counter will appear on the TV

screen.

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

INDEX SEARCH

2 Enter your desired time

Use [K / L] until your desired time

appears. (Example: “2:50” stands for

2 hours 50 minutes)

TIME SEARCH

2 : 50

The tape will automatically stop when the counter

returns to 0:00:00 (approx.).

If you wish to cancel the Time

Search at this point, press [SETUP].

3 Begin Time Search

PICTURE SEARCH

By using [s B], the unit will rewind or fast forward

to the specified point.

The time counts down during the search. When the

TV/VCR

This feature is very useful in finding or skipping over

a particular scene on a tape. In this mode, the sound

will be muted.

display shows

automatically.

“0:00”, the tape will start playback

TO CANCEL DURING TIME SEARCH

1 Start Picture Search

During playback, press [D] or [E] to view at a

high speed (in forward/reverse).

Press [C /

STOP/EJECT] on the unit or

[STOP

This will delete the selected time.

2 Change searching speed

Press [D] or [E] again to view at super high

speed (in LP/SLP modes only).

- 27 -

Download from Www.Somanuals.com. All Manuals Search And Download.

INDEX SEARCH

1 Select “INDEX SEARCH”

Press [SETUP].

Using [K / L] point to “INDEX

SEARCH”, then press [ENTER].

- TV/VCR SETUP -

TIMER PROGRAMMING

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TV/VCR

This feature provides a method of indexing the start-

ing point so that it can be easily returned to in either

fast forward or rewind mode.

TIME SEARCH

INDEX SEARCH

The index mark will be made automatically when

[RECORD] is pressed. It will also be marked at

the starting point of Timer recording and OTR.

The index mark will not be recorded if [PAUSE F]

is pressed and released during recording.

The time gap between making the index marks on

the tape should be greater than 1 minute for SP

recording, 2 minutes for LP recording and 3 min-

utes for SLP recording.

•

2 Enter your desired number

Use [K / L] until the number of

programs that you want to skip

appears.

INDEX SEARCH

0 3

•

(Example: “03” for 3 programs)

•

The Index Search mode will be canceled if the pro-

cedures are not activated in 30 seconds.

•

In some cases, the index mark at the beginning of

video tape cannot be detected.

Example: You are watching program number 4 and

want to fast forward to program number 7. You

must skip three programs.

•

3 Begin Index Search

Use [s B]. The unit begins rewinding or fast for-

warding to the beginning of desired program.

NOTE:

Every time an index signal is skipped, the number

•

in the program indicator decreases by one.

CURRENT PLAYBACK PROGRAM

Beginning of

the tape

End of

the tape

4 After Index Search

When the preset program is reached, the unit will

start playback automatically.

•

Pro.1 Pro.2 Pro.3 Pro.4 Pro.5 Pro.6 Pro.7

A video cassette must be inserted in the unit for

this function to work.

INDEX MARK

The number of Index Searches can be set up to 20.

This function will not operate in the recording mode.

When you want to cancel the Index Search while

in progress, press [STOP C].

•

SPECIAL FEATURES

REAL TIME TAPE COUNTER

AUTO REWIND-EJECT

TV/VCR

When the end of a tape is reached during record-

ing, playback, or fast-forward, the tape will auto-

matically rewind to the beginning. After rewinding

finishes, the unit will eject the tape and turn itself

off.

This shows the elapsed recording or playback time in

hours, minutes, and seconds. (The displayed time will

not change on a blank tape or blank portions on the

tape.) The “–” indication will appear when the tape has

rewound further than “0:00:00” on the tape counter.

•

This function is operative when Repeat Play is set

to the [OFF] position.

The tape will not auto-rewind during timer record-

ing or One Touch Recording.

•

- 28 -

Download from Www.Somanuals.com. All Manuals Search And Download.

RECORDING

Make sure ...

The unit must be turned on.

Insert a cassette tape with its erase-prevention tab in place. (If necessary, rewind or fast forward the tape to

the point at which you want to begin recording.)

•

NOTES:

This unit will ONLY record and view the same channel.

This unit cannot record the contents from the built-in DVD.

•

SKIPPING UNWANTED

NORMAL RECORDING

SCENES DURING RECORDING

TV/VCR

You can ONLY watch the same TV program that is

being recorded.

Press [PAUSE F] to temporarily

stop recording.

PAUSE

Press [PAUSE F] or [RECORD]

to resume recording.

NOTES:

1 Select the channel to be recorded

Use the Number buttons or

CH 10

[CH.

After 5 minutes, the unit will

automatically switch to the recording mode to pre-

vent tape damage.

•

NOTE:

If Closed Caption mode is on, the On-Screen

Display will appear for 5 seconds, then disappear.

•

If the unit is connected to a cable box or satellite

box, the unit must be on CH3 or CH4, then the

channel to be recorded must be selected on the

cable box or satellite box.

•

2 Select the tape speed

Press [SPEED] to select the

desired tape speed (SP/ SLP).

3 Begin recording

Press [RECORD].

REC

4 Stop recording

Press [STOP C].

- 29 -

Download from Www.Somanuals.com. All Manuals Search And Download.

Time(s)

1 time

Display

Recording length

(normal recording)

OTR (One Touch Recording)

2 times

3 times

0:30

1:00

30 minutes

60 minutes

TV/VCR

This function enables you to set a recording length

simply by pressing [I REC/OTR] on the unit.

Make sure ...

17 times

8:00

480 minutes

The unit must be turned on.

Insert a cassette tape with its erase-prevention tab

in place. (If necessary, rewind or fast forward the

tape to the point at which you want to begin

recording.)

•

COPYING A VIDEO CASSETTE

(Requires a VCR or camcorder)

TV/VCR

NOTES:

You can make copies of video tapes made by friends

or relatives for your enjoyment.

You cannot start OTR with the remote control.

•

Recording starts immediately when

You can not copy a DVD to a videotape.

[I REC/OTR] is pressed.

When [I REC/OTR] is pressed 18 times, the unit

•

WARNING: Unauthorized recordings of

copyrighted video tapes may be an

infringement of copyright laws.

returns to the normal recording mode.

To stop the OTR operation, press [C STOP] on

the unit or on the remote control.

To show the remaining time, press [DISPLAY] on

the remote control so that “OTR” appears on the

TV screen. (It will show up momentarily then dis-

appear.)

•

Connect your unit and a source (Playing) VCR using

the following diagram.

•

[Fig.8]

[This unit]

–

PLAY F.FWD

STOP

HEADPHONE VIDEO

AUDIO

Recording stops when the display shows 0:00.

Please note that in the SLP mode maximum

recording time, assuming the tape is started at the

beginning, is 8 hours using T-160 (or 6 hours

using T-120).

EJECT

•

[Ex: Source VCR or

camcorder]

If the tape runs out before the end time, the unit

will switch to the stop mode immediately, ejects

the tape and turns itself off.

Even if [POWER] is pressed during OTR, the unit

continues recording.

•

Audio/Video

cable

(not supplied)

AUDIO

OUT

•

VIDEO

OUT

1 Select the channel to be recorded

1)Insert a pre-recorded video cassette into the source

VCR or camcorder.

Use the Number buttons or [CH.

2)Insert a blank video cassette or one you want to

record over, into the unit’s cassette compartment.

3)Press [SPEED] on remote control for the unit to

select the desired recording speed (SP/SLP).

NOTE:

If the unit is connected to a cable box or satellite

box, the unit must be on CH3 or CH4, then the

channel to be recorded is selected on the cable box

or satellite box.

•

4)Use [CHANNEL

appears on the screen.

] on the unit until “AUX”

5)Press [I REC/OTR] on the unit.

6)Begin playback of the tape in the source VCR or

camcorder.

2 Select the tape speed

Press [SPEED] to select the desired tape speed

(SP/SLP).

NOTE:

3 Begin OTR

For best results during copying, use the front

•

panel controls whenever possible. The remote

control might affect the source VCR’s playback

operation.

Press [I REC/OTR] on the unit as

OTR (2 : 30)

many times as needed. The record-

ing length will be determined by

the number of times you press

[I REC/OTR]. Each time it is

pressed, the recording time will be

7)To stop copying, press [C / A STOP/EJECT] on

the unit, then stop the tape on the source VCR or

camcorder.

increased by 30 minutes up to 8 hours.

- 30 -

Download from Www.Somanuals.com. All Manuals Search And Download.

TIMER RECORDING

AUTOMATIC TIMER

RECORDING

1 Select “TIMER PROGRAMMING”

- TV/VCR SETUP -

Press [SETUP].

TIMER PROGRAMMING

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

Confirm “TIMER PROGRAM-

MING” is pointed by pressing [K],

then press [ENTER].

If you have not yet set the clock,

“MANUAL CLOCK SET” appears. If so, follow

TV/VCR

You may set the unit to start and end a recording

while you are away. You can set 8 programs to record

on specific days, daily or weekly within a 1 year

period.

TIME SEARCH

INDEX SEARCH

•

steps 3 to 8 on page 18. Then set the timer recording.

In the example below, the timer is being set to record:

DATE:

July 4th, 2005

2 Select your desired program position (1 to 8)

SETTING TIME: from 7:30PM to 8:50PM

CHANNEL:

TAPE SPEED:

Using [K / L] select the desired

– TIMER PROGRAMMING –

CH DATE BEGIN END

program position, then press [B].

CH61

- - -/- - - - - -:- -

-:- - - -

Make sure ...

If a cable box or satellite box is connected with the

unit you will be limited to record only one channel,

and the channel selector on the unit must be select-

ed to the output channel of the boxes CH 3 or CH

4 and then the actual channel to be recorded must

be selected on the boxes.

•

3 Set the channel number

Use [K / L] until the desired chan-

nel number appears (Example:

CH61), then press [B].

– TIMER PROGRAMMING –

CH DATE BEGIN END

- - -/- - - - - -:- -

61 -/- - - - - -:- -

- - -/- - - - - -:- -

-:- - - -

Clock must be set to the correct time and date

before setting the timer.

•

NOTE:

The unit must be turned on to program it.

Insert a cassette tape with its erase-prevention tab

in place. (If necessary, rewind or fast forward the

tape to the point at which you want to begin

recording.)

If the unit is connected to a cable box or satellite

box, the unit must be on CH3 or CH4, then the

channel to be recorded is selected on the cable box

or satellite box.

•

4 Select once, every day or weekly recording

The channel you want to record is properly set in

advance. (Refer to page 17.)

•

For once recording :

Press [K] until the desired date

appears.

– TIMER PROGRAMMING –

CH DATE BEGIN END

Avoid overlap of programs ...

There is a chance that a program will not be record-

ed, when programs overlap;

The program with an earlier start has priority.

Once the earliest program finishes, the overlapping

programs will begin recording in sequence.

When the starting time is the same, the program set

on the highest position in the program list has pri-

ority.

The illustration below demonstrates the sequence

- - -/- - - - - -:- -

61 7/04 MON -:- -

- - -/- - - - - -:- -

-:- - - -

(Example: “7/04” for July 4th)

Then press [B].

•

For every day recording : To record a TV program

at the same time on the same channel every day.

•

(Example: Monday through Sunday)

– TIMER PROGRAMMING –

Press [L] until “EVRY DAY”

appears, then press [B].

CH DATE

BEGIN END

- - -/- - - - - -:- -

61 EVRY DAY -:- -

- - -/- - - - - -:- -

-:- - - -

•

of recordings.

Program 1

Program 2

Program 3

10:00AM - 11:00AM

9:00AM - 10:00AM

9:30AM - 12:00PM

For weekly recording : To record a TV program at

the same time on the same channel every week.

Recording Sequence

(Example: every Monday)

– TIMER PROGRAMMING –

Program 1

10:00AM-11:00AM

Program 2

9:00AM-10:00AM

Program 3

CH DATE

BEGIN END

Press [L] until “EVRY” and

your desired day of the week

appear together, then press [B].

- - -/- - - - - -:- -

61 EVRY MON -:- -

- - -/- - - - - -:- -

-:- - - -

9:30AM-12:00PM

9:00AM

10:00AM

11:00AM

12:00PM

*Recording period is SHADED

- 31 -

Download from Www.Somanuals.com. All Manuals Search And Download.

NOTES:

5 Set beginning hour

Use [K / L] until the desired hour

appears.

(Example: “ 7, PM” for 7:30PM)

Then press [B].

– TIMER PROGRAMMING –

CH DATE BEGIN END

The display will not be turned on automatically at

•

the time the programmed recording begins. To

watch the currently recorded TV program or to

play a DVD disc, press [POWER] and [SELECT]

to choose the TV/VCR mode or the DVD mode.

- - -/- - - - - -:- -

-:- - - -

61 7/04 MON 7:12^P

- - -/- - - - - -:- -

If the tape runs out before the end time, the unit

will switch to the stop mode immediately and the

tape will be ejected.

•

6 Set beginning minute

Use [K / L] until the desired

minute appears.

(Example: “30” for 7:30PM)

Then press [B].

– TIMER PROGRAMMING –

CH DATE BEGIN END

- - -/- - - - - -:- -

-:- - - -

61 7/04 MON 7:30^P

- - -/- - - - - -:- -

TIMER PROGRAM EXTENSION

To shift the time schedule of an automatic timer

recording.

1)Press [POWER].

2)Repeat step 1 on page 31.

3)Press [RECORD] and select the desired program

using [K / L].

7 Set end hour

– TIMER PROGRAMMING –

CH DATE BEGIN END

Use [K / L] until the desired hour

appears.

- - -/- - - - - -:- -

-:- - - -

8:30^PM- -

-:- - - -

61 7/04 MON 7:30^P

- - -/- - - - - -:- -

(Example: “8, PM” for 8:50PM)

Then press [B].

4)Press [RECORD] again.

Each additional push will shift forward the

begin/end time for recording by 10 minutes. When

the recording is already in progress, each additional

push will shift forward the end time only. If you

want to cancel while setting, press [PAUSE F] on

the remote control. The recording time returns to

the original time.

8 Set end minute

Use [K / L] until the desired

minute appears.

(Example: “50” for 8:50PM)

Then press [B].

– TIMER PROGRAMMING –

CH DATE BEGIN END

- - -/- - - - - -:- -

-:- - - -

8:50^PM- -

-:- - - -

61 7/04 MON 7:30^P

- - -/- - - - - -:- -

NOTE:

9 Set the tape speed

Use [K / L] until the desired tape

speed appears. (Example: “SP”)

– TIMER PROGRAMMING –

CH DATE BEGIN END

When you shift forward the time schedule during

•

recording, the recording speed will automatically

be set to the SLP mode.

- - -/- - - - - -:- -

-:- - - -

8:50^PMSP

-:- - - -

61 7/04 MON 7:30^P

- - -/- - - - - -:- -

5)Press [ENTER] or [RETURN] to exit the setting

menu. Then press [SETUP] to return to original

mode.

10 Finish setting the program

Press [ENTER] or [RETURN] to complete setting.

TO CORRECT A PROGRAM

To set another program, repeat steps 2 to 10.

Press [SETUP] to exit the menu.

•

While setting a program; press [s] to go back one

step and enter the correct numbers using [K / L].

•

After setting a program;

1)Press [POWER].

•

11 Set the timer

Press [POWER] to set automatic timer recording.

The recording indicator lights up.

2)Repeat steps 1 to 2 on page 31.

3)Press [B] (or press [s] to go back one step)

until the part you want to correct begins flashing,

then make the changes using [K / L].

4)Press [POWER] to set automatic timer recording.

You must turn off the unit to activate automatic

timer recording.

•

If power is not turned off and you continue watch-

ing TV, “TIMER REC STANDBY” starts flashing

on the TV screen 2 minutes before the programmed

start time.

TO CANCEL AN AUTOMATIC TIMER

RECORDING

1)Press [POWER].

2)If recording is in progress, press

[C / A STOP/EJECT] on the unit.

3)Repeat steps 1 to 2 on page 31 and select a pro-

gram you want to cancel.

If the erase-prevention tab is removed, the cassette

will be ejected when [POWER] is pressed to off.

•

4)Press [C.RESET].

5)Press [SETUP] to return to TV mode.

- 32 -

Download from Www.Somanuals.com. All Manuals Search And Download.

TO CONFIRM THE TIMER SETTING

1)Press [POWER] so that the Recording indicator

light goes off.

AUTO RETURN

TV/VCR

2)Press [SETUP].

With this feature, after timer recording is finished,

the beginning of the recorded program(s) can be

searched for automatically.

3)Confirm “TIMER PROGRAMMING” is selected.

4)Press [ENTER]. The details of programs appear on

the TV screen.

5)Press [SETUP] to return to TV mode.

1 Select “USER’S SET UP”

- TV/VCR SETUP -

TIMER PROGRAMMING

Press [SETUP].

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

Using [K / L] point to “USER’S

SET UP”, then press [ENTER].

INDEX SEARCH

2 Set “AUTO RETURN” to [ON]

Using [K / L] point to “AUTO

RETURN”, then press [ENTER]

until [ON] appears.

USER’S SET UP

–

RENTAL

[OFF]

[ON]

REPEAT PLAY

AUTO RETURN

3 Auto Return will begin

When all the timer recordings are completed, the unit

will rewind to the beginning of the recorded pro-

gram(s).

NOTE:

If you press [POWER] while tape is rewinding,

the Auto Return will stop.

•

4 Watch the recorded program

Press [PLAY O].

TO CANCEL AUTO RETURN MODE

Repeat steps 1 to 2 and select [OFF] using [ENTER].

Even if there is a power failure of any kind, the

unit will retain its memory for this feature.

- 33 -

Download from Www.Somanuals.com. All Manuals Search And Download.

ON SCREEN DISPLAY

To check the Counter, Clock and Channel number on the TV screen, press [DISPLAY]. Each time you press

[DISPLAY], the TV screen will change as follows:

When the Closed Caption mode is ON:

When the Closed Caption mode is OFF:

The On Screen Display disappear after 5 seconds.

•

Counter mode: After 5 seconds, only the counter

•

remains. To clear it, press [DISPLAY].

This is true even if [MUTE] or [PAUSE F] is

•

pressed while recording.

Clock mode: After 5 seconds, only the clock and

the channel number remain. To clear them, press

•

[DISPLAY].

OFF mode

Clock/Counter mode

OFF mode Counter mode

Clock mode

STOP

5:40PM

CH2

STOP

5:40 PM

CH2

COUNT 0:12:34

After 5 seconds

5:40PM

CH2

COUNT 0:12:34

Counter

remains

Clock & Channel

remain

CABLE CHANNEL DESIGNATIONS

If you subscribe to cable TV, the channels are displayed as 1-125. Cable companies often designate channels

with letters or letter-number combinations. Please check with your local cable company. The following is a

chart of common cable channel designations.

CATV channel

TV Display

CATV channel

TV Display

CATV channel

TV Display

W+1

W+2

W+3

W+4

W+5

W+6

W+7

W+8

W+9

CATV channel

TV Display

W+10 W+11 W+12 W+13 W+14 W+15 W+16 W+17 W+18 W+19 W+20 W+21 W+22 W+23 W+24

46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

W+25 W+26 W+27 W+28 W+29 W+30 W+31 W+32 W+33 W+34 W+35 W+36 W+37 W+38 W+39

61 62 63 64 65 66 67 68 69 70 71 72 73 74 75

W+40 W+41 W+42 W+43 W+44 W+45 W+46 W+47 W+48 W+49 W+50 W+51 W+52 W+53 W+54

CATV channel

TV Display

CATV channel

TV Display

W+55 W+56 W+57 W+58

91 92 93 94

W+59 W+60 W+61 W+62 W+63 W+64

100 101 102 103 104 105

CATV channel

TV Display

A-5

A-4

A-3

A-2

A-1

CATV channel

TV Display

W+65 W+66 W+67 W+68 W+69 W+70 W+71 W+72 W+73 W+74 W+75 W+76 W+77 W+78 W+79

106

W+80 W+81 W+82 W+83 W+84

121 122 123 124 125

107

108

109

110

111

112

113

114

115

116

117

118

119

120

CATV channel

TV Display

- 34 -

Download from Www.Somanuals.com. All Manuals Search And Download.

DVD SECTION

ABOUT THE DISCS

PLAYABLE DISCS

Recorded

signals

Playable

discs

Disc size

Region code

Disc types

Mark (logo)

DVD-Video

* 1,2,4,6,10,11

Example

12 cm

8 cm

Title 1

Title 2

DVD-RW

DVD-R

Digital video

(MPEG2)

Chapter 1 Chapter 2 Chapter 3 Chapter 4 Chapter 1

Chapter 2

* 1,3,4,5,6

7,9,10

DVD+RW

DVD+R

* 1,3,4,5,6,8,9,10

Audio CD

* 4,6,10

Audio CD

Example

12 cm

8 cm

Digital audio

Track 1

Track 2

Track 5

Track 6

Track 3

Track 4

CD-RW

CD-R

* 4,5,6,9,10

is a trademark of DVD Format/Logo Licensing Corporation.

If you cannot play back a disc which bears one of the marks above, check the following notes.

*1: This unit conforms to the NTSC color system. Discs recorded in other color systems such as PAL cannot

be played back.

*2: Certain DVD-Video discs do not operate as described in this manual due to the intentions of the disc’s producers.

*3: Discs recorded in the VR (Video Recording) format cannot be played back.

*4: Scratched or stained discs may not be played back.

*5: Some discs cannot be played back because of incompatible recording conditions, characteristics of the

recorder or special properties of discs.

*6: You can play back discs which bear the marks above. If you use nonstandardized discs, this unit may not

play them back. Even if they are played back, the sound or video quality will be compromised.

*7: You may play back the unfinalized DVD-R/RW disc recorded in the video format on our brand’s DVD

recorder. However, depending on the recording status of a disc, the disc may not be played back at all or

normally (the picture or sound may not be smooth, etc.). In this case, you need to finalize the disc with

the DVD recorder. Refer to the manual accompanying the DVD recorder.

*8: Only the discs recorded in the video format and finalized can be played back.

Unfinalized discs cannot be played back. Depending on the recording status of a disc, the disc may not be

played back at all or normally (the picture or sound may not be smooth, etc.).

*9: If there is too much recording space left on a disc (the used portion is less than 55mm across), it may not

play back properly.

*10: Do not glue paper or put stickers on to the disc. These may damage the disc and the unit may not read it correctly.

*11: The number inside the symbol refers to a region of the world and a disc encoded in a specific region for-

mat can only be played back on unit with the same region code.

UNPLAYABLE DISCS

NEVER play back the following discs. Otherwise, malfunction may result!

DVD-RAM / CD-I / Photo CD / Video CD / DVD with region codes other than 1 or ALL /

DTS-CD / DVD-ROM for personal computers / CD-ROM for personal computers / MP3

On the following disc, the sound MAY NOT be heard.

Super Audio CD

NOTE: Only the sound recorded on the normal CD layer can be delivered.

The sound recorded on the high density Super Audio CD layer cannot be delivered.

Any other discs without compatibility indications

- 35 -

Download from Www.Somanuals.com. All Manuals Search And Download.

PLAYING A DISC

BASIC PLAYBACK

GENERAL FEATURES

DVD-V CD

DVD-V

VD may contain menus to navigate the disc and

access special features. Use the appropriate

Getting started

¡Turn on the power of amplifier and any other com-

Number buttons or [K / L / s / B] to highlight

your selection in the DVD main menu and press

[ENTER] to confirm.

ponents, if necessary.

Press [POWER].

¡The power will turn on.

NOTES:

¡Select DVD mode by pressing [SELECT], then

Press [A OPEN/CLOSE] to open disc load-

ing tray.

operate the DVD functions.

¡Unless stated, all operations described are based on

remote control use. Some operations can be carried

out using the menu bar on the TV screen.

Place the chosen disc in the tray, with the

label facing up.

DISC MENU

DVD-V

Press [DISC MENU].

¡The DVD main menu will appear.

¡If the feature is not available,

appear on the TV screen.

¡If disc menu is available on the disc, audio lan-

guage, subtitle options, chapters for the title and

other options will appear for selection.

symbol may

Press [PLAY O].

¡The tray will close automatically and playback will

then start from the first chapter or track of the disc.

¡Closing the disc tray manually or by pressing

[A OPEN/CLOSE] also starts playback.

¡If the playback does not start automatically, press

[PLAY O].

¡When you playback a DVD which features a title

menu, it may appear on the screen. In this case,

refer to “TITLE MENU” on this page.

Using [K / L / s / B] select an item and

press [ENTER] to confirm selection.

TITLE MENU

Press [STOP C] to stop playback.

DVD-V

NOTES:

Press [TITLE].

¡When the DVD mode has been switched to the

TV/VCR mode, the DVD mode shuts down first and

then the TV picture and sound appears in about 4

seconds. Similarly, when [POWER] is pressed to

turn off in the DVD mode, this mode shuts down

first and then the unit is turned off.

¡The title menu will appear.

¡If the feature is not available,

appear on the TV screen.

symbol may

Using [K / L / s / B] select an item, and

press [ENTER] to confirm selection.

¡A “prohibited icon” may appear at

the top-right on the TV screen dur-

ing operation, warning that a pro-

hibited operation has been encoun-

tered by the DVD or the disc.

¡With DVDs that use titles for

playback program signals, playback may start from

the second title or it may skip these titles.

¡During the playback of a two layered disc, pictures

may stop for a moment. This happens when the 1st

layer switches to the 2nd layer. This is not a mal-

function.

CALLING UP A MENU SCREEN

DURING PLAYBACK

¡Press [DISC MENU] to call up the DVD menu.

¡Press [TITLE] to call up the title menu.

NOTE:

¡Contents of menu and corresponding menu opera-

tions may vary between discs. Refer to the manual

accompanying the disc for details.

- 36 -

Download from Www.Somanuals.com. All Manuals Search And Download.

SLOW FORWARD /

SLOW REVERSE

RESUME

DVD-V CD

DVD-V

During playback, press [STOP C].

¡Resume message will appear on the TV screen.

During playback, press [PAUSE F].

Press and hold [D] or [E ] for a few

seconds.

Press [PLAY O], playback will resume from the

point at which playback was stopped.

¡“

1” or “ 1” appears on the screen.

¡To cancel resume, press [STOP C] twice.

¡The resume information stays on even when the

power is turned off.

To select another speed, repeat step 2 until

your required speed number appears on the

screen.

PAUSE

¡Slow forward or reverse speed varies with the disc.

Approximate speed is 1 (1/16), 2 (1/8) and 3 (1/2).

¡When you press buttons on the main unit, use

[SEARCH E / D].

DVD-V CD

During playback, press [PAUSE F].

To return to normal playback, press [PLAY O].

¡Playback will pause and sound will be muted.

To continue playback, press [PLAY O].

ZOOM

STEP BY STEP PLAYBACK

DVD-V

The Zoom function allows you to enlarge the video

image and to pan through the enlarged image.

DVD-V

During playback, press [PAUSE F].

¡Playback will pause and sound will be muted.

Press [ZOOM] during playback.

¡Playback will continue.

The disc goes forward by one frame each

time [PAUSE F] is pressed.

Press [ZOOM] repeatedly to select the

required zoom factor: ZOOM1, ZOOM2,

ZOOM3 or OFF.

To exit step by step playback, press [PLAY O].

FAST FORWARD /

FAST REVERSE

Use [K / L / s / B] to move the zoomed

picture across the screen.

To exit zoom mode, press [ZOOM] to OFF.

DVD-V CD

NOTES:

During playback, press and hold [D] or

[E ] for a few seconds.

¡Zooming function does not work while disc menu is

shown.

¡Zooming function is not available on some discs.

¡It may take several seconds to slide the zoomed pic-

ture.

¡“ D 1” or “E 1” appears on the screen.

To select another speed, repeat step 1 until

your required speed number appears on the

screen.

¡The picture may be distorted if you operate other

functions repeatedly (ex. [PAUSE ] or [E], etc.)

in the zoom mode.

¡For DVDs, fast forward/reverse search speed is dif-

ferent depending on the disc. Approximate speed is

1 (×2), 2 (×8), 3 (×20), 4 (×50) and 5 (×100).

¡For Audio CDs approximate speed is 1 (×2), 2 (×8)

and 3 (×30).

¡When you press buttons on the main unit, use

[SEARCHE / D].

To return to normal playback, press [PLAY O].

- 37 -

Download from Www.Somanuals.com. All Manuals Search And Download.

SEARCH FUNCTION

TRACK SEARCH

TIME SEARCH

DVD-V

There are three ways to begin playback on an Audio

CD at a specific track.

During playback, press [SEARCH MODE]

three times (CD: twice) to display the Time

Search on the TV screen.

Using the Number buttons

Within 30 seconds, enter a desired disc

time using the Number buttons.

Press the Number buttons to enter the

desired track number.

¡Playback will start at the specified time.

¡Press [CLEAR] to erase the incorrect input.

¡When there is no need to enter a number, “0”

¡Playback will start at the selected track.

¡For single digit tracks (1-9), press a single number

(eg. track 3, press [3]).

appears automatically. For example, “ 0 : 0

”

- - -

¡To play track 26, press [+10], [2], [6].

appears in the Time Search display if the total time

of the track or title is less than 10 minutes.

Using [SEARCH MODE]

Press [SEARCH MODE].

¡The track search display appears.

MARKER SETUP SCREEN

Within 30 seconds, select the desired track

number using the Number buttons.

DVD-V

Use markers to memorize your favorite places on a

disc.

¡For single digits press [0] first, if the total track of

the disc is 10 tracks or more.

¡Playback will start at the selected track.

Press [SEARCH MODE] four times

(CD: three times) during playback.

]

Using [

¡The display screen and Markers will appear on the

TV screen.

During playback, press [G] to move the next track.

Press it repeatedly to skip subsequent tracks. Press

[H ] to go back to beginning of the current track.

Press it repeatedly to go to the previous tracks.

¡If [H / G ] is pressed while the playback is

paused, the playback will be paused again after

skipping to the next track.

Using [s / B] select 1, 2, 3, 4, 5, 6, 7, 8, 9, or

10 and ensure that “

in the display.

” appears

- - - - - - - -

When the disc reaches the desired point,

press [ENTER].

NOTE:

¡[H / G ] are not operative when playback is

¡The Title or Track and elapsed playing time will

appear in the TV screen.

stopped.

To return to the Marker later, press

[SEARCH MODE] four times (CD: three

times) during playback and choose the

desired marker using [s / B], then press

[ENTER].

TITLE / CHAPTER SEARCH

DVD-V

Press [SEARCH MODE] once for the

Chapter search, twice for the Title search

NOTES:

¡Operations which erase all Markers:

– Opening the disc tray

during playback.

_/2

– Turning off the power

– Pressing [SELECT]

– Selecting “AC” at step 2 and pressing [ENTER]

Enter the desired chapter/title number using

the Number buttons.

¡To clear a marker:

– Using [s / B] select a cursor on to the marker

number and press [CLEAR].

¡You can mark up to 10 points.

¡Playback will start at the selected chapter or title.

¡Press [CLEAR] to erase the incorrect input.

¡For single digits press [0] first, if the total number of

chapter or title of the disc is 10 or more.

Press [SEARCH MODE] or [RETURN] to exit.

- 38 -

Download from Www.Somanuals.com. All Manuals Search And Download.

SPECIAL PLAYBACK FUNCTION

REPEAT

PROGRAM

REPEAT is available only during playback.

You may determine the order in which tracks will play.

REPEAT TITLE / CHAPTER

DVD-V

In the stop mode, press [MODE].

To activate the repeat function, press [REPEAT]

during playback.

¡The “PROGRAM” screen will appear.

Using [▲ / ▼] select a track, then press

[ENTER].

¡The repeat mode changes as described below every

time you press the button.

¡Press [CLEAR] to erase the

most recently entered track.

¡If the entire Program cannot be

displayed at once on a screen,

“G” appears to go to the next

page and “H” appears to go

back to the previous page.

PROGRAM

CD-DA

TOTAL 1:03:30

CHAPTER

TITLE

OFF

(repeat off)

3:30

5:10

3:30

4:30

5:00

3:10

5:10

1:30

2:30

10 4:20

11 3:00

12 3:20

17 4:10

22 2:50

2/3

(current chapter repeat) (current title repeat)

ENTER

1/4

PLAY

3:30

CLEAR

NOTES:

¡Repeat Title/Chapter is not available with some

scenes.

Repeat step 2 until you have selected all the

tracks you want to play in the program.

¡The REPEAT setting will be cleared when moving

to other title or chapter.

Press [PLAY O] to play the programmed tracks.

REPEAT TRACK

NOTES:

¡While the program is being played back, pressing

[STOP C] works as follows.

To activate the repeat function, press [REPEAT]

during playback.

– Press [STOP C] once and then [PLAY O] again,

playback will restart from the point where

[STOP C] was pressed. (Program continued)

– Press [STOP C] twice and then [PLAY O]

again, playback will restart from the track in the

usual way. (Program canceled)

¡The repeat mode changes as described below every

time you press the button.

TRACK

ALL

OFF

(repeat off)

(current track repeat)

(entire disc repeat)

¡Up to 99 tracks can be entered.

¡To erase all tracks in the program at once, select

“ALL CLEAR” at the bottom of the list at step 2.

¡If you like to repeat the current track in the program,

NOTES:

¡Repeat Track setting will be cleared when moving

to other track.

press [REPEAT] several times until “

TRACK”

appears during playback. If you like to repeat the

¡Repeat playback does not function during A-B

repeat playback.

entire program press [REPEAT] several times until

“

ALL” appears during playback.

A-B REPEAT

RANDOM PLAYBACK

DVD-V CD

¡“

Press [A-B] at your chosen starting point.

This function shuffles the playing order of tracks

A-” appears briefly on the TV screen.

instead of playback in the sequence.

¡“

Press [A-B] again at your chosen end point.

In the stop mode, press [MODE] twice.

¡“RANDOM” screen appears.

A-B” appears briefly on the TV screen, and the

RANDOM

repeat sequence begins.

CD-DA

TOTAL 0:45:55

RANDOM PROGRAM

no indication

To exit the sequence, press [A-B].

PLAY

NOTES:

¡The A-B repeat section can only be set within the cur-

rent title (for DVDs) or current track (for Audio CDs).

¡A-B repeat is not available with some scenes in DVD.

¡To cancel the A point which was set, press

[CLEAR].

Press [PLAY O] to start random playback.

NOTE:

¡If you like to repeat the current track in the random

selection, press [REPEAT] several times until

“

TRACK” appears during playback. If you like

¡A-B repeat playback does not function during title,

chapter, track or all repeat playback.

to repeat the entire random selection press

[REPEAT] several times until “ ALL” appears

during playback.

- 39 -

Download from Www.Somanuals.com. All Manuals Search And Download.

CHANGING THE SETTINGS

SUBTITLE LANGUAGE

AUDIO LANGUAGE

DVD-V

The unit allows you to select a language during DVD

disc (if multi languages are available) playback.

The unit allows you to select a language for subtitles

during DVD disc (if available) playback.

Press [AUDIO] during playback.

Press [SUBTITLE] during playback.

1.ENG Dolby D 3/2.1ch 48k/3

¡The subtitle language will

appear on the display bar at

the top of the TV screen.

1.ENG/6

Press [AUDIO] repeatedly to select your

desired language.

Press [SUBTITLE] repeatedly to select your

desired subtitle language.

NOTE:

¡Pressing [AUDIO] may not work on some DVDs

with multiple audio languages (e.g. DVDs which

allow audio language setting on the disc menu).

To turn off subtitles, press [SUBTITLE]

repeatedly until “OFF” appears.

NOTES:

¡Pressing [SUBTITLE] may not work on some

DVDs with multiple subtitle languages. In this

case, set it on the disc menu. (Operation varies

between discs. Refer to the manual of the disc.)

¡If the desired language is not shown after pressing

[SUBTITLE] several times, the disc does not have

subtitles in that language.

STEREO SOUND MODE

Press [AUDIO] repeatedly during playback to

select between “STEREO”, “L-ch” or “R-ch”.

NOT AVAILABLE

¡When “NOT AVAILABLE”

STEREO

appears on the TV screen, it

means no subtitle is recorded

on the scene.

STEREO - both right and left channels are active (stereo)

L-ch - only left channel is active

R-ch - only right channel is active

¡If you choose a language that has a 3 letter lan-

guage code, the code will be displayed every time

you change the Subtitle language setting. If you

choose any other languages, “---” will be displayed

instead. (Refer to page 43.)

- 40 -

Download from Www.Somanuals.com. All Manuals Search And Download.

CAMERA ANGLE

VIRTUAL SURROUND

DVD-V

Some DVD discs contain scenes which have been shot You can enjoy surround-sound effect over two speakers

simultaneously from various angles. You can change on this unit.

the camera angle when the “

screen.

” icon appears on the

Press [MODE] twice (CD: once) during play-

back.

OFF

Press [ANGLE] during playback.

¡The selected angle will be displayed on the display

bar at the top of the screen.

1 / 8

Press [ENTER] to set it “1” (Natural effect),

“2” (Emphasized effect) or “OFF”.

¡If the “ANGLE ICON” setting is “OFF” in the

Press [MODE] or [RETURN] to exit.

“OTHERS” menu, the “

(Refer to page 45.)

” icon will not appear.

NOTE: (for CD play only)

¡Virtual Surround will not be effective if the sound

mode is set to something other than STEREO.

Press [ANGLE] repeatedly to select your

desired angle.

BLACK LEVEL SETTING

DVD-V

Adjust the Black Level Settings to make the black

parts of the picture brighter.

Press [MODE] during playback.

OFF

Press [ENTER] to switch “ON/OFF”.

ON: Makes the dark parts brighter.

OFF: Shows the original picture as recorded.

(Initial setting)

Press [MODE] twice or [RETURN] to exit.

NOTE:

¡The setting will be saved even if the unit is turned

off.

- 41 -

Download from Www.Somanuals.com. All Manuals Search And Download.

THE ON-SCREEN INFORMATION

DVD-V

You can check the information about the current disc by pressing [DISPLAY].

For DVD-Vs

For Audio CDs

Press [DISPLAY] during playback to show

current Chapter.

Press [DISPLAY] during playback to show

the current Track.

¡The elapsed and remaining

playing time of the current

chapter will be displayed.

¡The elapsed and remaining

playing time of the current

track will be displayed.

9/49

0:00:00 -0:03:30

4/12 0:03:21 - 0:02:15

Press [DISPLAY] again to show current Title.

Press [DISPLAY] again to show current Total

Track.

¡The elapsed and remaining

playing time of the current

title will be displayed.

1/3 0:00:00 - 1:23:45

¡The elapsed and remaining

playing time of the total track

will be displayed.

4/12 0:13:45 - 0:45:40

Press [DISPLAY] again.

Press [DISPLAY] again to exit.

The bit rate and the current

repeat setting will be dis-

played.

¡If you are playing a dual layered disc, the layer

number will also be displayed (L0: Layer 0 is play-

ing. L1: Layer 1 is playing).

NOTE:

¡When you are playing a disc in PROGRAM or

RANDOM mode, “ PROGRAM” (or RAN-

DOM) will be displayed at step 2.

Press [DISPLAY] again to exit.

PROGRAM

- 42 -

Download from Www.Somanuals.com. All Manuals Search And Download.

CHANGING THE DVD SET UP ITEMS

Language

Code Language

Code

CUSTOM MENU

A-B

L-N

Abkhazian

Afar

Afrikaans

Albanian

Amharic

Arabic

Armenian

Assamese

Aymara

Azerbaijani

Bashkir

Basque

4748 Laothian

4747 Latin

4752 Latvian;Lettish

6563 Lingala

4759 Lithuanian

4764 Macedonian

5471 Malagasy

4765 Malay

5861

5847

5868

5860

5866

5957

5953

5965

5958

5966

5955

5964

5961

5960

6047

6051

6061

DVD-V

You can change the DVD player’s settings.

Press [SETUP] twice in the stop mode so

that the DVD SETUP menu appears.

4771 Malayalam

4772 Maltese

4847 Maori

SETUP

¡Press [L] to select “CUSTOM”

then press [ENTER].

QUICK

CUSTOM

INITIALIZE

5167 Marathi

Bengali;Bangla

Bhutani

Bihari

4860 Moldavian

5072 Mongolian

4854 Nauru

NOTE:

¡If the menu does not appear, press [PLAY O] first,

then press [STOP C]. Make sure the disc is in the

stop mode, then slowly press [SETUP] twice.

Bislama

Breton

4855 Nepali

4864 Norwegian [NOR]

4853

5971 Occitan

4851 Oriya

Oromo(Afan)

5759 Panjabi

4947 Pashto;Pushto

7254 Persian

4961 Polish

5464 Portuguese [POR]

4965 Quechua

5047 Rhaeto-Romance

6058 Romanian [RUM]

5160 Russian [RUS]

5161

5166 Samoan

Sangho

5261 Sanskrit

5256 Scots Gaelic

5255 Serbian

Bulgarian

Burmese

Byelorussian

O-R

6149

6164

6159

6247

6265

5247

6258

6266

6367

6459

6461

6467

Select the desired item.

C-E

Cambodian

Catalan

¡Using [K / L] select the desired item then press

[ENTER] to confirm.

Chinese [CHI]

Corsican

Croatian

Refer to the pages below to set up each item.

Czech

SETUP

CUSTOM

P 43 Step

Danish [DAN]

Dutch [DUT]

English [ENG]

Esperanto

Estonian

LANGUAGE

DISPLAY

AUDIO

PARENTAL

OTHERS

P 44 Step

6559

6553

6547

5350

6564

6554

6566

6660

6560

6550

6555

6565

6557

6558

6561

5165

6567

6569

6568

P 45 Step

F-H

Faroese

Fiji

P 45 Step

LANGUAGE SETTING

Finnish [FIN]

French [FRE]

Frisian

5264 Serbo-Croatian

5271 Sesotho

5358 Setswana

5747 Shona

Follow steps to in the “CUSTOM MENU” section

Galician

above.

Georgian

German [GER]

Greek [GRE]

Greenlandic

Guarani

5051 Sindhi

Using [K / L] select the desired item then

5158 Singhalese

5758 Siswat

5360 Slovak

press [ENTER].

SETUP

LANGUAGE

AUDIO:

Gujarati

Hausa

Hebrew

5367 Slovenian

5447 Somali

5569 Spanish [SPA]

5455 Sundanese

5467 Swahili

AUDIO

SUBTITLE

DISC MENU

ORIGINAL

OFF

ENGLISH

Sets the audio language.

SUBTITLE:

Hindi

Hungarian [HUN]

I-K

Icelandic [ICE]

Indonesian

Interlingua

Interlingue

Inupiak

Irish [IRI]

Italian [ITA]

Japanese [JPN]

Javanese

Kannada

Kashmiri

Sets the subtitle language.

DISC MENU:

Swedish [SWE]

5565

5560 Tagalog

5547 Tajik

5551 Tamil

5557 Tatar

5347 Telugu

5566 Thai

Sets the language for DVD menu.

6658

6653

6647

6666

6651

6654

4861

6655

6661

6665

6664

6657

6669

Using [K / L] select a setting then press

[ENTER].

SETUP

LANGUAGE

¡If “OTHER” is selected on

the “AUDIO”, “SUBTITLE”

or “DISC MENU” screen,

press four-digit number to

enter the code for the desired

language. (Refer to the lan-

guage code list.)

AUDIO

ORIGINAL

ENGLISH

FRENCH

5647 Tibetan

5669 Tigrinya

5760 Tonga

5765 Tsonga

5757 Turkish [TUR]

6469 Turkmen

5771 Twi

SETUP

Kazakh

Kinyarwanda

Kirghiz

Kirundi

Korean [KOR]

Kurdish

SUBTITLE

OFF

ENGLISH

FRENCH

6460

U-Z

5761 Ukrainian

5767 Urdu

Uzbek

6757

6764

6772

6855

6861

4971

6961

7054

5655

7161

7267

¡Only the languages supported

by the disc can be selected.

SETUP

Vietnamese

Volapuk

Welsh

DISC MENU

ENGLISH

FRENCH

SPANISH

Wolof

Xhosa

Yiddish

Yoruba

Zulu

Press [SETUP] to exit the menu.

NOTES:

If you choose a language that has a 3 letter language

code, the code will be displayed every time you change

the AUDIO or SUBTITLE language setting above. If

you choose any other languages, ‘---’ will be displayed

instead. (3 letter language code is written in bracket.)

¡Language Setting for Audio and Subtitle are not

valid for some discs due to default setting of the

disc. In this case, set them by pressing [AUDIO] and

[SUBTITLE]. (Refer to page 40.)

¡If you select a language that is not supported by the

disc, subtitle will automatically be set OFF and the

first item of the audio languages will be automatical-

ly set.

- 43 -

Download from Www.Somanuals.com. All Manuals Search And Download.

DISPLAY SETTING

AUDIO SETTING

Choose the appropriate Audio settings for your equip-

ment as it only affects during the playback of DVD

discs.

Follow steps to in the “CUSTOM MENU” section

on page 43.

Using [K / L] select the below items then

press [ENTER].

Follow steps to in the “CUSTOM MENU” section

on page 43.

TV MODE:

QUICK

Using [K / L] select the below items then

press [ENTER].

You can change certain aspects of the DVD display

screens and on-screen messages on the TV screen.

¡4:3 LETTER BOX (default):

To show black bars on top

and bottom of the screen.

DRC

SETUP

DRC

DOWN SAMPLING

DOLBY DIGITAL

AUDIO

SETUP

DISPLAY

(Dynamic Range Control):

¡To compress the range of soft

to loud sound.

BITSTREAM

TV MODE

STILL MODE

4:3 LETTER BOX

AUTO

¡4:3 PAN & SCAN: To show

a full height picture with both sides trimmed.

¡The default setting is “ON”.

SETUP

AUDIO

DOWN SAMPLING:

¡ON : Output in 48 kHz.

(default)

DRC

DOWN SAMPLING

DOLBY DIGITAL

BITSTREAM

STILL MODE

This function allows you to adjust picture resolution

and quality in the still mode.

¡OFF : Output the original

sound.

¡AUTO (default):

SETUP

DISPLAY

When playing disc with copyright Protection

¡If you select “OFF”, copyright protection will be

activated and sound will be down sampled at 48kHz.

Automatically select the best

resolution setting (FRAME

or FIELD) based on the data

characteristics of the pic-

tures.

¡FIELD: Select “FIELD” when the pictures are still

unstable even if “AUTO” is selected.

FIELD stabilizes the pictures, although the picture

quality may become coarse due to the limited

amount of data.

¡FRAME: Select “FRAME” to display relatively

motionless pictures in higher resolution.

FRAME improves the picture quality, although it

may unstabilize the pictures due to simultaneous

output of two field data.

TV MODE

STILL MODE

4:3 LETTER BOX

AUTO

SETUP

DRC

DOWN SAMPLING

DOLBY DIGITAL

AUDIO

DOLBY DIGITAL:

QUICK

BITSTREAM

Set to “BITSTREAM” when

the unit is connected to a

Dolby Digital Decoder.

¡BITSTREAM: Output a Dolby Digital signal

(default)

¡PCM: Convert the Dolby Digital to PCM

(2 channel stereo)

Press [SETUP] to exit the menu.

QUICK MENU

¡You can select the “TV MODE” or “DOLBY DIGITAL” from the QUICK menu quickly. To access the

QUICK menu, select “QUICK” instead of “CUSTOM” at step on page 43.

LANGUAGE SETTING FOR THE ON-SCREEN MENUS

¡You can access the TV/VCR SETUP menu by pressing [SETUP] from the DVD mode. Refer to

“MENU LANGUAGE” on page 21 to change the language for the on-screen menus.

- 44 -

Download from Www.Somanuals.com. All Manuals Search And Download.

PARENTAL CONTROL

IF YOU FORGET THE PASSWORD

Parental Control limits the disc viewing that exceed

your setting (with a password or playback will stop).

This feature allows you to prevent discs with alterna-

tive scenes from being played by your children.

Press the Number buttons [4], [7], [3], [7] at

step 3. Then enter your new password.

¡Password will be cleared and parental level will be

set to “ALL”.

PARENTAL LEVEL

Proceed with steps 4 to 6 again.

Parental Level allows you to set the rating level of

your DVD discs. Playback will stop if the disc’s rat-

ings exceed the level you set.

OTHER SETTINGS

Follow steps to in the “CUSTOM MENU” section

on page 43.

Follow steps to in the “CUSTOM MENU” section

on page 43.

Using [K / L] select the below items, then

press [ENTER].

Enter your four-digit password then press

[ENTER].

SETUP

OTHERS

SETUP

PARENTAL

ANGLE ICON

AUTO POWER OFF ON

PASSWORD

Enter current password.

ANGLE ICON:

¡Press [ENTER] repeatedly to turn Angle icon

“ON” or “OFF”.

Using [K / L] select “PARENTAL LEVEL”

¡The default setting is “ON”.

then press [ENTER].

SETUP

PARENTAL

AUTO POWER OFF:

¡Press [ENTER] repeatedly to turn Auto Power off

“ON” or “OFF”.

PARENTAL LEVEL

PASSWORD CHANGE

ALL

¡The default setting is “ON” and the screen saver

program starts when there is no input from the unit

for 5 minutes in the stop mode. After the screen

saver program is activated for 15 minutes, the

power is automatically turned off.

Using [K / L] select the desired level then

press [ENTER].

SETUP

PARENTAL

PARENTAL LEVEL

ALL

7 [NC-17]

6 [R]

Press [SETUP] to exit the menu.

NOTES:

INITIALIZE

When doing this for the first time, enter any 4 digits.

(except for 4737) That number will be used as the pass-

word. (in the event you forget the password, see below)

DVD-V

¡To change the password, using [K / L] select

“PASSWORD CHANGE” at step 4 then press

[ENTER]. Enter the four-digit password, then

press [ENTER].

This allows you to return all selections of SETUP

(except for “PARENTAL” and menu language) to

their default settings.

¡With some DVDs, it may be difficult to find if they

are compatible with parental lock. Be sure to check

if the parental lock function operates in the way that

you have set.

Press [SETUP] twice in the stop mode so

that the “INITIALIZE” menu appears.

Using [K / L] select “INITIALIZE” then

¡Record the password in case you forget it.

press [ENTER].

SETUP

QUICK

CUSTOM

INITIALIZE

CONTROL LEVELS

ALL

All parental lock is cancelled.

Using [K / L] select “YES” then press

[ENTER] twice.

Level 8

DVD software of any grade (adult/general/children)

can be played back.

All the settings (except for

SETUP

INITIALIZE

Levels 7 to 2

“PARENTAL” and menu

Initialize?

YES

Only DVD software intended for general use and language) will be cleared.

children can be played back.

¡To cancel the initialization,

Level 1

select “NO”.

Only DVD software intended for children can be

played back, with those intended for adult and

general use prohibited.

Press [SETUP] to exit the menu.

- 45 -

Download from Www.Somanuals.com. All Manuals Search And Download.

TROUBLESHOOTING GUIDE

If the unit does not perform properly when operated as instructed in this Owner’s Manual, check the unit, con-

sulting the following checklist.

PROBLEM

CORRECTIVE ACTION

Make sure the power plug is connected to an AC outlet.

Make sure the power is turned on.

Aim the remote control directly at the sensor on the front of the unit.

Reduce the distance to the unit. You have to be within 23 feet.

Replace the batteries in the remote control.

Re-insert the batteries with their polarities (+/- signs) as indicated.

Tune your radio to an empty AM station so that you hear a lot of

noises. Then, turn the volume up. If you hear some signal sound from

the radio when pressing buttons on the remote control, the remote con-

trol is working.

No power

•

The unit does not respond to the

remote control

Check if the correct mode is selected. If not switch the mode by

pressing [SELECT], whichever you need.

•

TV/VCR Mode

Sometimes a performance problem can be easily solved by checking seemingly apparent but often overlooked

possibilities. Before arranging for service, check these items. It could save your time and money.

PROBLEM

No picture or sound

CORRECTIVE ACTION

Make sure the AC cord is connected to an AC outlet.

Check antenna connection.

Press [SELECT] to select TV mode.

Then try other TV feature.

•

Let the unit program its tuner memory.

Adjust direction or replace antenna.

Adjust picture controls.

Check for broken pin of the antenna cable.

Adjust volume control on remote control or main unit.

Press [MUTE] to restore sound.

•

No picture or poor picture on the

unit

•

No sound or poor sound

Bars On Screen

•

If outside antenna is being used, check for broken wire.

Check for local interference.

Picture Distorted or Blurred

Try a new channel, if OK, then possible station trouble.

If outside antenna is being used, check for broken wire.

Try a new channel, if OK, then possible station trouble.

If outside antenna is being used, check for broken wire.

Check for local interference.

Try a new channel, if OK, then possible station trouble.

Is antenna connected to jack on the back of the set?

If outside antenna is being used, check for broken wire.

Adjust “COLOR” control.

Try a new channel, if OK, then possible station trouble.

Is antenna connected to jack on the back of the set?

If outside antenna is being used, check for broken wire.

Check for local interference.

Try a new channel, if OK, then possible station trouble.

Is antenna connected to jack on the back of the set?

If outside antenna is being used, check for broken wire.

Adjust “CONTRAST” & “BRIGHT” control.

Picture Rolls Vertically

Lines or Streaks in Picture

No Color

Poor Reception on Some Channels

Ghosts in Picture

Weak Picture

- 46 -

Download from Www.Somanuals.com. All Manuals Search And Download.

PROBLEM

Sound OK, Picture Poor

CORRECTIVE ACTION

Try a new channel, if OK, then possible station trouble.

Is antenna connected to jack on the back of the set?

If outside antenna is being used, check for broken wire.

Check for local interference.

Adjust “CONTRAST” & “BRIGHT” control.

Try a new channel, if OK, then possible station trouble.

Check for local interference.

Make sure the timer recording is set correctly.

Make sure the power is off.

Make sure the unit’s clock is set correctly.

Make sure the tape has an erase-prevention tab. If need, cover the

hole with plastic tape.

Adjust tracking control for a better picture using [CHANNEL K / L]

on the unit.

Head cleaning may be necessary. Refer to “AUTO HEAD

• CLEANING” on page 49.

Make sure the AC cord is connected to an AC outlet.

Check batteries in remote control.

You can not copy a copyrighted video tape. You are experiencing

•

Picture OK, Sound Poor

Timer recording is not possible

Cannot go into the recording mode

Playback picture is partially noisy

•

No picture but the audio is OK in

playback

No operation by infrared remote

control

Video or color fades in and out

when making a copy of a video tape

•

copy guard protection.

Magnetism from nearby appliances and geomagnetism might affect

the color of the TV picture. Move the unit away from the appliances,

the unit can repair itself automatically. If you want to repair immedi-

ately, unplug the power cord, then plug it in again 30 minutes later or

so. This automatically resets the unit.

•

Different color marks on screen

•

CLOSED CAPTION PROBLEM

POSSIBLE REMEDY

Misspelling in captions

Error committed by the closed captioning production company.

Possible in a live broadcast. Not in case of a prerecorded program.

•

Text is not shown in its entirety or

a delay occurs from what is being

said

A few seconds of delay is common for live broadcast.

Display capacity may not exceed 220 words per minute. If a dialogue

exceeds that rate, selective editing is used to insure that the captions

remain up-to-date with the current TV screen dialogue.

•

Captions scrambled with white

boxes

Caused by interferences of building, power lines, thunderstorms, etc.

•

No captions in a program which

must contain closed caption

The broadcast may use a time compression process to speed up the

program. The decoder cannot read the compressed information and

captions will be lost.

•

No captions in a prerecorded

videotape which indicated closed

captions included

Possibility of a illegal copy or an erroneous copying process

accidentally performed by the fabricator.

•

Black box in the TV screen

You are in TEXT mode. Select a CAPTION mode (“C1”, “C2”) or

Caption “OFF”.

•

- 47 -

Download from Www.Somanuals.com. All Manuals Search And Download.

DVD Mode

PROBLEM

CORRECTIVE ACTION

Insert a correct video disc that plays on this unit.

Press [SELECT] to select DVD mode, then try other DVD feature.

Insert the disc.

No picture

•

Disc cannot be played

Clean the disc.

Place the disc correctly, with the label side up.

Cancel the parental lock or change the control level.

Connect the audio cables firmly.

No sound

Turn the power of the audio component on.

Correct the audio output settings.

Correct the input settings on the audio component.

This unit does not support DTS audio. This is not a malfunction.

No DTS audio is output

Distorted picture

There are some cases where pictures may be slightly distorted,

which are not a sign of a malfunction.

Although pictures may stop for a moment, this is not a malfunction.

The selected language is not available for audio or subtitles on the

DVD. (This is not a malfunction.)

•

Audio or subtitle language

does not match the set up

The camera angle cannot be changed The DVD does not contain sequences recorded from different

•

camera angles. (This is not a malfunction.)

Audio or subtitle language cannot be The DVD does not contain audio source or subtitles in the selected

•

changed

language. (This is not a malfunction.)

•

“Prohibited icon” appears on the

screen, prohibiting an operation

CD sound dropout

That operation is prohibited by the unit or the disc.

(This is not a malfunction.)

Scratched disc. Replace the disc with an unscratched one.

No CD reproduction

DVD picture dropout

DVD picture freeze

DVD picture in mosaic

No DVD reproduction

NOTES:

Some functions are not available in specific modes, but this is not a malfunction. Read the description in

this Owner’s Manual for details on correct operations.

•

Playback from a desired track and random playback are not available during program playback.

•

- 48 -

Download from Www.Somanuals.com. All Manuals Search And Download.

MAINTENANCE

1.Please visit your local Audio/Video store and pur-

CABINET CLEANING

chase a good quality VHS Video Head Cleaner.

2.If a Video Head Cleaner does not solve the prob-

lem, please call our help line mentioned on the

front page, to locate an Authorized Service Center.

Wipe the front panel and other exterior surfaces of

the unit with a soft cloth immersed in lukewarm

water and wrung dry.

•

Never use a solvent or alcohol. Do not spray insec-

•

NOTES:

ticide liquid near the unit. Such chemicals may

cause damage and discoloration to the exposed sur-

faces.

Remember to read the instructions included with

the video head cleaner before use.

•

Clean video heads only when problems occur.

•

AUTO HEAD CLEANING

SERVICING

Automatically cleans video heads as you insert or

remove a cassette, so you can see a clearer picture.

•

Should your unit become inoperative, do not try to

•

correct the problem by yourself. There are no user-

serviceable parts inside. Turn off, unplug the power

cord and please call our help line mentioned on

the front page, to locate an Authorized Service

Center.

Playback picture may become blurred or interrupt-

•

ed while the TV program reception is clear. Dirt

accumulated on the video heads after long periods

of use or the usage of rental or worn tapes can

cause this problem.

If a streaky or snowy picture appears during play-

back, the video heads in your unit may need to be

cleaned.

IF THE LASER OPTICAL PICKUP UNIT IS DIRTY

If the unit still does not perform properly when it is operated, while referring to the relevant sections and to

“TROUBLESHOOTING GUIDE” in this Owner’s Manual, the laser optical pickup unit may be dirty.

•

Consult your dealer or an Authorized Service Center for inspection and cleaning of the laser optical pickup

unit.

DISC HANDLING

Handle the discs so that fingerprints and dust do

not adhere to the surfaces of the discs.

To clean-off, use a soft cloth.

•

Do not use a hard cloth since this will mar the disc.

Wipe the disc in a straight line from center to edge.

Never wipe with a circular motion.

Do not use detergent or abrasive cleaning agents.

Always store the disc in its protective case when it

is not used.

- 49 -

Download from Www.Somanuals.com. All Manuals Search And Download.

SPECIFICATIONS

GENERAL SPECIFICATIONS

ELECTRICAL SPECIFICATIONS

Sound output:

2 speakers, 1W, 8 ohm

TV/VCR

CRT:

24 inch in-line gun,

90˚ deflection tube

NTSC-M

OTHER SPECIFICATIONS

Terminals

Television system:

Closed caption system: §15.119/FCC

Antenna input:

VHF/UHF/CATV

75 ohm unbalanced (F-type)

RCA connector [ 1

RCA connector [ 2

Video Heads:

Tape width:

Tape speed

SP:

LP:

SLP:

Tuner channel

TV VHFLow:

TV VHFHigh:

TV UHF:

CATV

Rotary four-head

1/2 inch

Video input:

Audio L/R input:

Headphone:

Coaxial digital

audio output:

1/8" stereo (3.5mm)

33.40mm/sec.

16.67mm/sec.

11.12mm/sec.

One pin jack,

500m Vpp (75 ohm)

Digital encoded

Remote control:

#2~#6

#7~#13

#14~#69

infrared light system

Operating

temperature:

5°C to 40°C

(41°F~104°F)

Power requirements: AC 120V, 60Hz

Power consumption

VHF:

MID band:

SUPER band:

HYPER band:

A5~A1, A~I

J~W

W+1~W+84

(Maximum):

Picture tube:

Dimensions:

120W

24"

H : 22-11/16" (576mm)

W : 24-1/8" (612mm)

D : 19"

61.7 lbs. (28kg)

(482mm)

Weight:

DVD

Product type:

Discs:

DVD Player

DVD video, Audio CD

Output signal format: NTSC color

Designs and specifications are subject to change without notice.

If there is a discrepancy between languages, the default language will be English.

•

- 50 -

Download from Www.Somanuals.com. All Manuals Search And Download.

12. Indicador de grabación

INDICE

Parpadea durante la grabación. Se ilumina durante el

modo de espera de grabación controlada por

temporizador.

■ INDICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

■ CONTROLES DE OPERACIÓN Y FUNCIONES . . . . . 51

PARA INSERTAR LAS PILAS . . . . . . . . . . . . . . . . . . . . 52

■ PREPARACIÓN PARA LA UTILIZACIÓN . . . . . . . . . . 52

CONEXIONES DE ANTENA/CABLE . . . . . . . . . . . . . . 52

CONEXIÓN A TOMAS DE ENTRADA DELANTERAS 53

CONEXIÓN A UN AMPLIFICADOR ESTÉREO

13. Botón REC/OTR (Panel frontal)

Presione para empezar la grabación manual. Presione

repetidamente para empezar la grabación instantánea (OTR).

Botón RECORD (Mando a distancia)

Presione para empezar la grabación manual.

EQUIPADO CON TOMAS DE ENTRADA DIGITAL.

(para DVD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

CONEXIÓN A UN DECODIFICADOR DOLBY DIGITAL

(para DVD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

14. Botón E REW (para TV/VCR)

Presione para rebobinar la cinta o para ver la imagen

rápidamente en dirección de retroceso durante el modo

de reproducción. (Búsqueda en dirección de retroceso)

SECCIÓN DE TV/VCR

15. Botón F.FWD D (para TV/VCR)

■ FUNCIONES Y AJUSTES DE TV. . . . . . . . . . . . . . . . . 54

PARA MIRAR UN PROGRAMA DE TV . . . . . . . . . . . . 54

IDIOMA DEL MENÚ . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

AJUSTE DEL RELOJ . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

■ GRABACIÓN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

GRABACIÓN NORMAL . . . . . . . . . . . . . . . . . . . . . . . . 55

Presione para adelantar rápidamente la cinta o para ver la

imagen rápidamente en dirección de avance durante el modo

de reproducción. (Búsqueda en dirección de avance)

16. Botón C / A STOP/EJECT

Presione para detener la cinta. Presione en el modo de

parada para retirar la cinta de la unidad.

SECCIÓN DE DVD

17. Ventanilla del sensor de mando a distancia

REPRODUCCIÓN BÁSICA . . . . . . . . . . . . . . . . . . . . . . 55

MENÚ DE DISCO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

REANUDACIÓN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

18. Toma HEADPHONE

Para conectar auriculares (no suministrados) y escuchar

en privado.

CONTROLES DE

19. Toma de entrada VIDEO

Conecte aquí la toma de salida de video de una

videocámara o de una videograbadora.

OPERACIÓN Y FUNCIONES

20. Tomas de entrada AUDIO L/R

Conecte aquí las tomas de salida de audio de una

videocámara o de una videograbadora.

• Consulte la figura 1 de la página 9 para el

panel frontal de la unidad

• Consulte la figura 2 de la página 9 para el

mando a distancia

21. Compartimiento del cassette

22. Botón PICTURE

• Consulte la figura 3 de la página 10 para la

vista posterior

Presione para ajustar la imagen.

23. Botones numéricos

1. Botón POWER

Presione para encender y apagar la unidad.

Modo TV/VCR:

Presione dos cifras para acceder directamente al canal

deseado.

K L

2. Botones VOLUME (VOL.)

Presione para controlar el nivel de volumen del DVD y

el televisor.

No olvide presionar [0] antes de elegir un canal de una

sola cifra.

Botón +100

Presione para seleccionar canales de televisión por

cable cuyo número sea superior a 99.

Modo DVD:

Presione para introducir el número deseado.

Botón +10

Presione para introducir números superiors a 9.

3. Botones SKIP H / G (para DVD)

Presione una vez para omitir capítulos o pistas y

desplazarse a un punto específico.

Botones SEARCH E / D (para DVD)

Mantenga el botón presionado para cambiar la

velocidad de reproducción en avance o retroceso.

4. Botón B PLAY

Inicia la reproducción del contenido del disco o cinta.

5. Botón C STOP

(Panel frontal) Detiene la operación del disco.

(Mando a distancia) Detiene la operación del disco o el

casete.

6. Botón A OPEN/CLOSE

Presione para insertar un disco en la bandeja o retirarlo

de ella.

7. Bandeja de carga del disco

8. Indicador DVD

Se ilumina durante el modo DVD.

24. Botón PAUSE F

Hace una pausa en la reproducción del disco o cinta.

25. Botón SPEED

Presione para seleccionar la velocidad de grabación

deseada: SP/SLP.

26. Botón C.RESET

Presione para poner el contador en 0:00:00.

Presione también para cancelar un ajuste de programa

de temporizador.

27. Botón DISPLAY

Modo TV/VCR:

Indica el contador o el número del canal y la fecha

actual en la pantalla del televisor.

Modo DVD:

9. Botón SELECT

Presione para cambiar al modo TV/VCR, modo de

entrada externa o modo de DVD. El modo

seleccionado (TV/VCR o DVD) se visualiza en el

indicador del panel delantero.

Indica el estado actual en la pantalla del televisor.

28. Botón SETUP

Presione para entrar o salir del menú de configración

de televisor o DVD.

10. Indicador TV/VCR

Se ilumina durante el modo TV/VCR.

K L

29. Botón TITLE

11. Botones CHANNEL (CH.)

Para visualizar el menú de títulos.

Utilice para seleccionar canales memorizados.

- 51 -

Download from Www.Somanuals.com. All Manuals Search And Download.

30. Botón CLEAR

PARA INSERTAR LAS PILAS

Presione para cancelar o borrar un ajuste entrado

actualmente.

1) Abra la cubierta del compartimiento de las pilas

empujando la cubierta del mando a

distancia en el sentido de la flecha.

2) Inserte 2 pilas “AA” en el

compartimiento de las pilas, en el

sentido indicado por las marcas de polaridad (+/-).

3) Vuelva a poner la cubierta.

31. Botón MODE

Presione para llamar la pantalla de la reproducción

programada o la de reproducción aleatoria en el modo

de parada.

Presione para llamar la pantalla de ajuste del nivel del

negro o la pantalla de sonido ambiental durante la

reproducción.

32. Botón SEARCH MODE

Presione para localizar un punto deseado.

33. Botón AUDIO

Modo TV/VCR:

PREPARACIÓN PARA LA

UTILIZACIÓN

Presione para seleccionar el modo de sonido deseado cuando

vea un programa de TV o reproduzca o grabe un casete.

Modo DVD:

Presione para seleccionar un modo de sonido o idioma

de audio deseado.

CONEXIONES DE ANTENA/CABLE

34. Botón SUBTITLE

Consulte la figura 4 de la página 12

Presione para seleccionar el idioma de subtítulos

deseado.

Nota para el instalador de sistemas CATV:

Esta nota tiene la finalidad de llamar la atención

del instalador de sistemas CATV para que tenga

en cuenta el Artículo 820-40 de la NEC, que

proporciona recomendaciones para hacer una

conexión a tierra apropiada y, en particular,

especifica que la tierra del cable debe conectarse

al sistema de puesta a tierra del edificio, tan cerca

del punto de entrada del cable como sea posible.

35. Botón REPEAT

Repite la reproducción del disco, título, capítulo o pista

actual.

36. Botón ANGLE

Presione para cambiar el ángulo de la cámara y ver la

secuencia que se está reproduciendo desde un ángulo

diferente (si existe).

37. Botón A-B (modo DVD)

Repite la reproducción de una sección seleccionada.

38. Botón RETURN

Permite volver a la pantalla anterior en el menú de

configuración.

NOTA:

Antes de enchufar la antena a la toma ANT. de la

•

39. Botones K / L / { / B

unidad, compruebe que la clavija no esté doblada.

Si esta doblada, póngala derecha como se muestra

en la ilustración, y luego conéctela en la toma

ANT. de la unidad.

Modo TV/VCR:

Presione para seleccionar un modo de ajuste en el

menú que aparece en la pantalla del televisor.

Presione también para seleccionar o establecer ajustes

en un menú en particular.

Clavija doblada

Modo DVD:

Presione para hacer una selección en el menú.

40. Botón ENTER

Cable

Clavija

Presione para establecer un ajuste.

(Necesita enderezarse)

(Clavija derecha)

41. Botón DISC MENU

Muestra menú del DVD.

42. Botón ZOOM

Para su seguridad y para evitar que se dañe

la unidad, desenchufe el cable de antena de la

toma ANT. antes de mover la unidad.

•

Amplía parte de la imagen reproducida de un DVD.

43. Botón MUTE

Suprime la salida de sonido. Presione de nuevo para

restablecer el sonido.

44. Botón SLEEP

Utilice para ajustar el temporizador de dormir.

45. Toma ANT.

Conecte a una antena, sistema de televisión por cable o

sistema de satélite.

46. Cable de alimentación

Conecte a un toma de CA estándar (120 V/60 Hz).

NOTA:

Antes de conectar el cable de alimentación de una toma

de CA estándar, retírelo del gancho para evitar dañarlo.

•

47. Toma AUDIO OUT COAXIAL

Conecte solamente a la entrada digital de un

amplificador externo o decodificador (para audio de

DVD solamente).

- 52 -

Download from Www.Somanuals.com. All Manuals Search And Download.

CONEXIÓN A TOMAS DE

ENTRADA DELANTERAS

Cuando vea un programa grabado en otra fuente

(videograbadora o videocámara), utilice las tomas de

entrada AUDIO/VIDEO de la parte delantera de la

unidad.

CONEXIÓN A UN DECODIFICADOR

DOLBY DIGITAL (para DVD)

Si utiliza esta unidad para reproducir un disco DVD

grabado en formato de sonido envolvente Dolby

Digital de 5,1 canales, la unidad emitirá un flujo de

datos DOLBY DIGITAL desde su toma AUDIO

OUT COAXIAL. Si conecta la unidad a un

decodificador Dolby Digital, podrá disfrutar de una

tonalidad más convincente y real, con un sonido

envolvente potente y de alta calidad similar al de los

cines.

Conecte las tomas de salida de audio/vídeo de otra

fuente a las tomas AUDIO L/R y VIDEO de esta

unidad.

K L

Después, presione [SELECT] o [CH.

que aparezca “AUX” en la pantalla.

] hasta

Utilice cables digitales coaxiales de audio

(disponibles en el comercio) para hacer las

conexiones de audio.

Consulte la figura 5 de la página 13

NOTA:

•

Cuando conecte una videograbadora monofónica

(otra fuente) a esta unidad, conecte la toma de

salida de audio de la videograbadora monofónica

(otra fuente) a la toma AUDIO L de esta unidad. El

audio saldrá igualmente por los canales izquierdo y

derecho.

Consulte la figura 7 de la página 14

NOTAS:

Asegúrese de apagar todos los componentes del

sistema antes de conectar otro componente.

•

Consulte los manuales de instrucciones de los

componentes que va a conectar a la unidad.

Si conecta un decodificador Dolby Digital, ajuste

la función “DOLBY DIGITAL” a “BITSTREAM”

para salida de audio en el modo de configuración.

CONEXIÓN A UN AMPLIFICADOR

•

ESTÉREO EQUIPADO CON TOMAS

DE ENTRADA DIGITAL (para DVD)

•

Utilice un cable digital coaxial de audio (disponible en

el comercio) para hacer las conexiones de audio.

Conexión a un amplificador equipado con tomas de

entrada digital, platina MD o platina DAT.

A menos que se haga la conexión a un

•

decodificador Dolby Digital, ajuste la función

“DOLBY DIGITAL” a “PCM” para salida de

audio en el modo de configuración. La

reproducción en una unidad utilizando ajustes

incorrectos puede generar ruido y distorsión, y

también puede provocar daños a los altavoces.

Consulte la figura 6 de la página 13

NOTAS:

• La fuente de audio de un disco grabado en formato

de sonido envolvente Dolby Digital de 5,1 canales

no se puede grabar como sonido digital mediante

una platina MD o DAT.

Fabricado bajo licencia de Dolby

Laboratories. “Dolby” y el símbolo de la

doble D son marcas comerciales de Dolby

Laboratories.

Asegúrese de apagar todos los componentes del

•

• ^sC^iso^tn^es^mul^ate^anlo^tes^sm^da^en^cu^oaⁿle^es^ctd^ae^{r o}in^trs^otru^cocc^mio^pn^oeⁿs^end^te^e.los

• A^coj^mus^pte^onla^enf^tu^en^sc^qió^un^e“^vD^aO^aL^coBⁿY^ecD^taI^rG^aIT^laA^uLⁿ”^ida^a“^dP^.CM”

para salida de audio en el modo de configuración.

La reproducción en una unidad utilizando ajustes

incorrectos puede generar ruido y distorsión, y

también puede provocar daños a los altavoces.

- 53 -

Download from Www.Somanuals.com. All Manuals Search And Download.

IDIOMA DEL MENÚ

SECCIÓN DE TV/VCR

TV/VCR

FUNCIONES Y AJUSTES

DE TV

1 Seleccione “LANGUAGE”

Presione [SETUP].

Presione [K / L] para apuntar a “LANGUAGE”.

PARA MIRAR UN PROGRAMA DE TV

TV/VCR

2 Seleccione “ENGLISH”, “ESPAÑOL” o

“FRANÇAIS”

1 Enchufe el cable eléctrico

Enchufe el cable eléctrico de la unidad en un

tomacorriente de CA del hogar.

NOTA:

Presione [ENTER] repetidamente para seleccionar

“ENGLISH” = inglés, “ESPAÑOL” o

“FRANÇAIS” = francés.

Si aparecen números en la esquina de la pantalla,

presione [POWER] sin desenchufar el cable

eléctrico.

•

3 Salga del modo de idioma

Presione [SETUP] para salir del menú.

NOTAS:

Esta función afecta sólo el idioma en el menú de la

pantalla y no la fuente de audio.

Si por alguna razón, el menú está en francés,

presione [SETUP], presione [K / L] para apuntar

al “LANGAGE [FRANÇAIS]” y presione

[ENTER] repetidamente para seleccionar el

idioma deseado y presione [SETUP].

•

2 Encienda la unidad

Presione [POWER] para encender la unidad.

•

3 Seleccione el número de canal

K L

Presione [CH.

] o los botones numéricos para

seleccionar su número de canal deseado.

Nota para el uso de los botones numéricos:

¡Debe colocar un cero antes de los números de canal

de una sola cifra (por ejemplo: 02, 03, 04, etc.).

AJUSTE DEL RELOJ

Cuando seleccione canales de cable de más de 99,

presione primero [+100] y después las dos últimas

cifras. (Ejemplo: para seleccionar el canal 125,

primero presione [+100] y después presione [2] y [5].)

TV/VCR

AJUSTE MANUAL DEL RELOJ

Asegúrese ...

La unidad debe estar encendida.

En el siguiente ejemplo, el reloj debe estar en:

4 Ajuste el sonido

•

X Y

Presione [VOL.

] para ajustar el volumen.

FECHA

HORA DE AJUSTE

6 de mayo, 2005

5:40PM

Presione [MUTE] para silenciar instantáneamente el

sonido.

Presione nuevamente para recuperar el nivel de

sonido anterior.

NOTA:

1 Seleccione “AJUSTE RELOJ”

Presione [SETUP].

Presione [K / L] para seleccionar “AJUSTE RELOJ”

y presione [ENTER].

K L

Si presiona [CH.

] en el modo DVD, puede

•

cambiar los canales de TV. Incluso si apaga la

unidad en el modo DVD, cuando vuelva a

encender, volverá al modo TV/VCR.

2 Seleccione “AJUSTE MANUAL RELOJ”

Presione [K / L] para seleccionar “AJUSTE

MANUAL RELOJ” y presione [ENTER].

PARA VER CANALES DE CABLE O

SATELITE

Si la unidad está conectada a una caja de cable o

•

K L

caja de satélite, presione [CH.

] para

3 Seleccione el mes

seleccionar CH3 o CH4 de acuerdo con el ajuste

de canal de salida del dispositivo y seleccione el

canal deseado en el dispositivo.

Presione [K / L] hasta que aparezca el mes deseado.

(Ejemplo: Mayo → “05”)

Presione [B]. (O presione [s] para volver un paso.)

PARA VER UNA ENTRADA EXTERNA

Cuando se conecta un equipo externo en las tomas

de entrada AUDIO/VIDEO frontales, presione

K L

4 Seleccione el día

•

Presione [K / L] hasta que aparezca el día deseado.

(Ejemplo: 6º → “06”)

[SELECT] o [CH.

] repetidamente hasta que

aparezca “AUX” en la pantalla.

Presione [B].

- 54 -

Download from Www.Somanuals.com. All Manuals Search And Download.

SECCIÓN DE DVD

5 Seleccione el año

REPRODUCCIÓN BÁSICA

Presione [K / L] hasta que aparezca el año deseado.

(Ejemplo: “2005”)

DVD-V

Presione [B].

Para empezar

¡Conecte la alimentación del amplificador y otros

6 Seleccione la hora

componentes, si es necesario.

Presione [K / L] hasta que aparezca la hora deseada.

(Ejemplo: “5”, “PM”)

Presione [POWER].

¡La alimentación se conectará.

Presione [B].

Presione [A OPEN/CLOSE] para abrir la

bandeja de carga del disco.

7 Seleccione los minutos

Presione [K / L] hasta que aparezcan los minutos

deseados.

Ponga el disco deseado en la bandeja, con

la etiqueta hacia arriba.

(Ejemplo: “40”)

Presione [PLAY O].

La bandeja se cerrará automáticamente y la reproducción

comenzará desde el primer capítulo o pista del disco.

8 Haga funcionar el reloj

Presione [SETUP].

Aunque no aparezcan los segundos, empezará a

contar desde 00 cuando presione [SETUP]. Utilice

esta característica para sincronizar el reloj con la hora

real.

¡La reproducción también empieza cerrando

manualmente la bandeja del disco o presionando

[

OPEN/CLOSE].

¡Si la reproducción no comienza automáticamente,

presione [PLAY O].

Cuando reproduzca un DVD que tenga grabado un

menú de títulos, el menú podrá aparecer en la pantalla.

GRABACIÓN

GRABACIÓN NORMAL

TV/VCR

Presione [STOP

C] para detener la reproducción.

MENÚ DE DISCO

DVD-V

SOLO puede ver el mismo programa que se está

grabando.

Presione [DISC MENU].

¡Aparecerá el menú principal de DVD.

¡Si no existe la función, puede aparecer el símbolo

en la pantalla de TV.

¡Si el menú de disco existe en el disco, aparecerán el

idioma de audio, opciones de subtítulo, capítulos

para el título y otras opciones para su selección.

1 Seleccione el canal a grabar

K L

Presione los botones numéricos o [CH.

NOTA:

Si la unidad está conectada a una caja de cable o

caja de satélite, la unidad debe estar en CH3 o

CH4 y debe seleccionarse el canal a grabar en la

caja de cable o caja de satélite.

•

Presione [K / L / s / B] para seleccionar

un ítem y presione [ENTER] para confirmar

la selección.

2 Seleccione la velocidad de la cinta

REANUDACIÓN

Presione [SPEED] para seleccionar la velocidad de

cinta deseada (SP/SLP).

DVD-V

Durante la reproducción, presione

[STOP C].

3 Empiece a grabar

Presione [RECORD].

¡Aparecerá el mensaje de continuación en la pantalla de TV.

Presione [PLAY O], la reproducción continuará

desde el punto donde se paró la reproducción.

4 Pare la grabación

Presione [STOP C].

¡Para cancelar la continuación, presione dos veces

[STOP C].

¡La información de continuación permanece activada

incluso cuando apaga el interruptor principal.

- 55 -

Download from Www.Somanuals.com. All Manuals Search And Download.

LIMITED WARRANTY

FUNAI CORP. will repair this SYLVANIA product, free of charge in the USA in the event of defect in materials or

workmanship as follows:

DURATION:

PARTS:

FUNAI CORP. will provide parts to replace defective parts without charge for one (1) year from the

date of original retail purchase. Two (2) years for Picture Tube. Certain parts are excluded from this

warranty.

LABOR: FUNAI CORP. will provide the labor without charge for a period of ninety (90) days from the date of

original retail purchase.

LIMITS AND EXCLUSIONS:

THIS WARRANTY IS EXTENDED ONLY TO THE ORIGINAL RETAIL PURCHASER. A PURCHASE RECEIPT

OR OTHER PROOF OF ORIGINAL RETAIL PURCHASE WILL BE REQUIRED TOGETHER WITH THE

PRODUCT TO OBTAIN SERVICE UNDER THIS WARRANTY.

This warranty shall not be extended to any other person or transferee.

This warranty is void and of no effect if any serial numbers on the product are altered, replaced, defaced, missing

or if service was attempted by an unauthorized service center. This SYLVANIA Limited warranty does not apply to

any product not purchased and used in the United States.

This warranty only covers failures due to defects in material or workmanship which occurs during normal use. It

does not cover damage which occurs in shipment, or failures which are caused by repairs, alterations or product not

supplied by FUNAI CORP., or damage which results from accident, misuse, abuse, mishandling, misapplication,

alteration, faulty installation, improper maintenance, commercial use such as hotel, rental or office use of this product

or damage which results from fire, flood, lightning or other acts of God.

THIS WARRANTY DOES NOT COVER PACKING MATERIALS, ANY ACCESSORIES (EXCEPT REMOTE

CONTROL), ANY COSMETIC PARTS, COMPLETE ASSEMBLY PARTS, DEMO OR FLOOR MODELS.

FUNAI CORP. AND ITS REPRESENTATIVES OR AGENTS SHALL IN NO EVENT BE LIABLE FOR ANY

GENERAL, INDIRECT OR CONSEQUENTIAL DAMAGES ARISING OUT OF OR OCCASIONED BY THE

USE OF OR THE INABILITY TO USE THIS PRODUCT. THIS WARRANTY IS MADE IN LIEU OF ALL

OTHER WARRANTIES, EXPRESS OR IMPLIED, AND OF ALL OTHER LIABILITIES ON THE PART OF

FUNAI, ALL OTHER WARRANTIES INCLUDING THE WARRANTY OF MERCHANTABILITY AND

FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED BY FUNAI AND ITS

REPRESENTATIVES IN THE UNITED STATES.

ALL WARRANTY INSPECTIONS AND REPAIRS MUST BE PERFORMED BY AN AUTHORIZED SERVICE

CENTER. THIS WARRANTY IS ONLY VALID WHEN THE UNIT IS CARRIED-IN TO AN AUTHORIZED

SERVICE CENTER.

IMPORTANT:

THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY HAVE OTHER RIGHTS

THAT VARY FROM STATE TO STATE. IF, AT ANY TIME DURING THE WARRANTY PERIOD, YOU ARE

UNABLE TO OBTAIN SATISFACTION WITH THE REPAIR OF THIS PRODUCT, PLEASE CONTACT FUNAI

CORP.

ATTENTION:

FUNAI CORP. RESERVES THE RIGHT TO MODIFY ANY DESIGN OF THIS PRODUCT WITHOUT

PRIOR NOTICE.

To locate your nearest AUTHORIZED SERVICE CENTER or for general service inquiries, please

FUNAI CORPORATION

Cutomer Service

Tel :1-800-968-3429

http://www.SylvaniaConsumerElectronics.com

19900 Van Ness Avenue, Torrance, CA 90501

Printed in Thailand

1EMN21011

T2151UB ★★★★★

Download from Www.Somanuals.com. All Manuals Search And Download.

Sharp Projector PG C45S User Manual
Sony Cassette Player CFD F10L User Manual
Sony Digital Camera 560TVL User Manual
Sony Recording Equipment MDM X4 User Manual
Sony Stereo System STRDH100 User Manual
Sony Stereo System Z L30 User Manual
Sumo Stereo Receiver Summing Amplifier User Manual
Superior Indoor Fireplace SDVPF N B User Manual
Symphonic VCR SL240C User Manual
Tannoy Cell Phone HCB 700 User Manual