Sylvania TV DVD Combo 6727DE User Manual

OWNER’S  
MANUAL  
COLOR TV/VCR/DVD TRIPLE COMBO  
(27 inch)  
6727DE  
SUPPLIED ACCESSORIES  
ACCESSORIES  
PART NO.  
Remote Control Unit NE222UD  
Batteries  
2 AA Batteries  
0EMN02539  
Owner’s Manual  
INSTRUCCIONES EN ESPAÑOL INCLUIDAS.  
As an ENERGY STAR®  
Partner, our company has  
determined that this product meets  
the ENERGY STAR® guidelines for  
energy efficiency. ENERGY STAR®  
is a U.S. registered mark.  
If you need additional operating assistance after reading this owner’s  
manual or to order replacement accessories, please call  
TOLL FREE : 1-800-968-3429.  
Or visit our WEB SITE at http://www.funai-corp.com  
Please read before using this equipment  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FIGURE A  
EXAMPLE OF ANTENNA GROUNDING AS PER  
NATIONAL ELECTRICAL CODE  
ANTENNA  
LEAD I N  
WI RE  
GROUND  
CL AMP  
ANTENNA  
DISCHARGE UNIT  
(NEC SECTION 810-20)  
ELECTRI C  
SERVICE  
EQUIPMENT  
GROUNDING CONDUCTORS  
(NEC SECTION 810-21)  
GROUND CLAMPS  
NEC  
-
NATIONAL ELECTRICAL CODE  
POWER SERVICE GROUNDING  
ELECTRODE SYSTEM  
(NEC ART 250, PART H)  
S2898A  
13.Outdoor Antenna grounding-If an outside antenna or  
cable system is connected to the TV/VCR/DVD, be sure  
the antenna or cable system is grounded so as to provide  
some protection against voltage surges and built-up static  
charges. Article 810 of the National Electrical Code,  
ANSI/NFPA No. 70, provides information with respect to  
proper grounding of the mast and supporting structure,  
grounding of the lead-in wire to an antenna discharge unit,  
size of grounding conductors, location of antenna-discharge  
unit, connection to grounding electrodes, and requirements  
for the grounding electrode. (Fig. A)  
19.Damage Requiring Service-Unplug this TV/VCR/DVD  
from the wall outlet and refer servicing to qualified service  
personnel under the following conditions:  
a. When the power-supply cord or plug is damaged or frayed.  
b. If liquid has been spilled, or objects have fallen into the  
TV/VCR/DVD.  
c. If the TV/VCR/DVD has been exposed to rain or water.  
d. If the TV/VCR/DVD does not operate normally by follow-  
ing the operating instructions. Adjust only those controls  
that are covered by the operating instructions, as improper  
adjustment of other controls may result in damage and will  
often require extensive work by a qualified technician to  
restore the TV/VCR/DVD to its normal operation.  
14.Lightning-For added protection for this TV/VCR/DVD  
receiver during a lightning storm, or when it is left unat-  
tended and unused for long periods of time, unplug it from  
the wall outlet and disconnect the antenna or cable system.  
This will prevent damage to the TV/VCR/DVD due to  
lightning and power-line surges.  
e. If the TV/VCR/DVD has been dropped or damaged in any  
way.  
f. When the TV/VCR/DVD exhibits a distinct change in per-  
formance-this indicates a need for service.  
15.Power Lines-An outside antenna system should not be  
located in the vicinity of overhead power lines or other  
electric light or power circuits, or where it can fall into  
such power lines or circuits. When installing an outside  
antenna system, extreme care should be taken to keep from  
touching such power lines or circuits as contact with them  
might be fatal.  
20.Replacement Parts-When replacement parts are required,  
be sure the service technician has used replacement parts  
specified by the manufacturer that have the same character-  
istics as the original part. Unauthorized substitutions may  
result in fire, electric shock, injury to persons or other haz-  
ards.  
16.Overloading-Do not overload wall outlets and extension  
21.Safety Check-Upon completion of any service or repairs to  
this TV/VCR/DVD, ask the service technician to perform  
routine safety checks to determine that the TV/VCR/DVD  
is in proper operating condition.  
cords as this can result in a risk of fire or electric shock.  
17.Object and Liquid Entry-Never push objects of any kind  
into this TV/VCR/DVD through openings as they may  
touch dangerous voltage points or short out parts that could  
result in a fire or electric shock. Never spill liquid of any  
kind on the TV/VCR/DVD.  
22.Heat-This TV/VCR/DVD product should be situated away  
from heat sources such as radiators, heat registers, stoves,  
or other products (including amplifiers) that produce heat.  
18.Servicing-Do not attempt to service this TV/VCR/DVD  
yourself as opening or removing covers may expose you to  
dangerous voltage or other hazards. Refer all servicing to  
qualified service personnel.  
- 3 -  
EN  
1B15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PRECAUTIONS  
IMPORTANT COPYRIGHT INFORMATION  
LASER SAFETY  
Unauthorized copying, broadcasting, public perfor-  
mance and lending of discs are prohibited.  
This unit employs a laser. Only a qualified service  
person should remove the cover or attempt to ser-  
vice this device, due to possible eye injury.  
This product incorporates copyright protection tech-  
nology that is protected by method claims of certain  
U.S. patents and other intellectual property rights  
owned by Macrovision Corporation and other rights  
owners. Use of this copyright protection technology  
must be authorized by Macrovision Corporation,  
and is intended for home and other limited viewing  
uses only unless otherwise authorized by  
CAUTION: USE OF CONTROLS OR ADJUST-  
MENTS OR PERFORMANCE OF PROCE-  
DURES OTHER THAN THOSE SPECIFIED  
HEREIN MAY RESULT IN HAZARDOUS  
RADIATION EXPOSURE.  
Macrovision Corporation. Reverse engineering or  
disassembly is prohibited.  
CAUTION: VISIBLE AND INVISIBLE LASER  
RADIATION WHEN OPEN AND INTERLOCK  
DEFEATED. DO NOT STARE INTO BEAM.  
LOCATION: INSIDE, NEAR THE DECK  
MECHANISM.  
FCC WARNING- This equipment may gener-  
ate or use radio frequency energy. Changes or  
modifications to this equipment may cause  
harmful interference unless the modifications  
are expressly approved in the instruction man-  
ual. The user could lose the authority to oper-  
ate this equipment if an unauthorized change  
or modification is made.  
This Class B digital apparatus complies with  
Canadian ICES-003.  
Cet appareil numérique de la classe B est con-  
forme à la norme NMB-003 du Canada.  
RADIO-TV INTERFERENCE  
CAUTION: TO PREVENT ELECTRIC SHOCK,  
MATCH WIDE BLADE OF PLUG TO WIDE  
SLOT, FULLY INSERT.  
This equipment has been tested and found to com-  
ply with the limits for a Class B digital device, pur-  
suant to Part 15 of the FCC Rules. These limits are  
designed to provide reasonable protection against  
harmful interference in a residential installation.  
This equipment generates, uses, and can radiate  
radio frequency energy and, if not installed and  
used in accordance with the instructions, may cause  
harmful interference to radio communications.  
However, there is no guarantee that interference  
will not occur in a particular installation. If this  
equipment does cause harmful interference to  
radio or television reception, which can be deter-  
mined by turning the equipment off and on, the  
user is encouraged to try to correct the interfer-  
ence by one or more of the following measures:  
1) Reorient or relocate the receiving antenna.  
2) Increase the separation between the equipment  
and receiver.  
ATTENTION: POUR ÉVITER LES CHOCS  
ÉLECTRIQUES, INTRODUIRE LA LAME LA  
PLUS LARGE DE LA FICHE DANS LA  
BORNE CORRESPONDANTE DE LA PRISE  
ET POUSSER JUSQU’AU FOND.  
3) Connect the equipment into an outlet on a cir-  
cuit different from that to which the receiver is  
connected.  
4) Consult the dealer or an experienced radio/TV  
technician for help.  
- 4 -  
EN  
1B15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WARNING  
LOCATION  
Moisture condensation may occur inside the unit  
when it is moved from a cold place to a warm place  
or after heating a cold room or under conditions of  
high humidity. If a DVD is played in a TV/VCR/  
DVD which has moisture, it may damage the DVD  
and TV/VCR/DVD. Therefore when the condensation  
occurs inside the unit, turn the POWER on and allow  
at least 2 hours for the unit to dry out.  
For safe operation and satisfactory performance of  
your TV/VCR/DVD, keep the following in mind  
when selecting a place for its installation:  
Shield it from direct sunlight and keep it away from  
sources of intense heat.  
Avoid dusty or humid places.  
Avoid places with insufficient ventilation for proper  
heat dissipation. Do not block the ventilation holes at  
the top or bottom of the unit. Do not place the unit  
on a carpet because this will block the ventilation  
holes.  
SYMBOLS USED IN THIS MANUAL  
The following symbols below appear in some head-  
ings and notes in this manual, with the following  
meanings  
Install unit in a horizontal position.  
Avoid locations subject to strong vibration.  
Do not place the TV/VCR/DVD near strong magnetic  
fields.  
TV/VCR  
: Description refers to TV/VCR operation (in the  
TV/VCR mode).  
Avoid moving TV/VCR/DVD to locations where  
temperature differences are extreme.  
DVD-V  
: Description refers to playback of DVD video discs  
(in the DVD mode).  
AVOID THE HAZARDS OF  
ELECTRICAL SHOCK AND FIRE  
CD  
: Description refers to playback of audio CDs  
(in the DVD mode).  
Do not handle the power cord with wet hands.  
Do not pull on the power cord when disconnecting  
it from an AC wall outlet. Grasp it by the plug.  
MP3  
: Description refers to playback of MP3 discs  
(in the DVD mode).  
If by accident, water is spilled on your unit, unplug  
the power cord immediately and take the unit to our  
Authorized Service Center for servicing.  
Do not put your fingers or objects into the  
TV/VCR/DVD disc loading tray.  
QUICK  
: Description refers to the items to be set by the  
QUICK mode (in the DVD mode).  
Do not place anything directly on top of the unit.  
A NOTE ABOUT RECYCLING  
This product’s packaging materials are recyclable and can be reused. Please dispose of any materials in  
accordance with your local recycling regulations.  
Batteries should never be thrown away or incinerated but disposed of in accordance with your local regula-  
tions concerning chemical wastes.  
The serial number of this product may be found on the back of the unit. No other TV/VCR/DVD has the same  
serial number as yours. You should record the number and other vital information here and retain this book as  
a permanent record of your purchase to aid identification in case of theft. Serial numbers are not kept on file.  
Date of Purchase  
Dealer Purchase from  
Dealer Address  
Dealer Phone No.  
Model No.  
Serial No.  
- 5 -  
EN  
1C29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TABLE OF CONTENTS  
STILL PICTURE . . . . . . . . . . . . . .26  
TIME SEARCH . . . . . . . . . . . . . . .39  
MARKER SETUP SCREEN . . . . . .39  
C IMPORTANT SAFEGUARDS . . . . .2  
VERTICAL HOLD CONTROL . . .26  
C PRECAUTIONS . . . . . . . . . . . . . . . .4  
C SPECIAL PLAYBACK . . . . . . . . . .27  
RENTAL PLAYBACK . . . . . . . . . .27  
AUTO REPEAT PLAYBACK . . . . .27  
C
SPECIAL PLAYBACK FUNCTION . . .40  
REPEAT . . . . . . . . . . . . . . . . . . . . .40  
PROGRAM . . . . . . . . . . . . . . . . . . .40  
RANDOM PLAYBACK . . . . . . . . .40  
LOCATION . . . . . . . . . . . . . . . . . . .5  
AVOID THE HAZARDS OF  
ELECTRICAL SHOCK AND FIRE .5  
WARNING . . . . . . . . . . . . . . . . . . . .5  
C SEARCH . . . . . . . . . . . . . . . . . . . . .28  
ZERO RETURN . . . . . . . . . . . . . . .28  
PICTURE SEARCH . . . . . . . . . . . .28  
TIME SEARCH . . . . . . . . . . . . . . .28  
INDEX SEARCH . . . . . . . . . . . . . .29  
SYMBOLS USED IN THIS  
MANUAL . . . . . . . . . . . . . . . . . . . . .5  
C PLAYING A MP3 DISC . . . . . . . . . .41  
MP3 PLAYBACK . . . . . . . . . . . . . .41  
REPEAT . . . . . . . . . . . . . . . . . . . . .41  
PROGRAM . . . . . . . . . . . . . . . . . . .41  
RANDOM PLAYBACK . . . . . . . . .41  
C TABLE OF CONTENTS . . . . . . . . . .6  
C FEATURES . . . . . . . . . . . . . . . . . . . .7  
C OPERATING CONTROLS AND  
FUNCTIONS . . . . . . . . . . . . . . . . . . .9  
C SPECIAL FEATURES . . . . . . . . . .29  
REAL TIME TAPE COUNTER . . .29  
AUTO REWIND-EJECT . . . . . . . .29  
C CHANGING THE SETTINGS . . . .42  
SUBTITLE LANGUAGE . . . . . . . .42  
AUDIO LANGUAGE . . . . . . . . . . .42  
STEREO SOUND MODE . . . . . . . .42  
CAMERA ANGLE . . . . . . . . . . . . .42  
BLACK LEVEL SETTING . . . . . . .42  
VIRTUAL SURROUND . . . . . . . . .42  
C PREPARATION FOR USE . . . . . . .11  
ANTENNA/CABLE  
CONNECTION . . . . . . . . . . . . . . . .11  
C RECORDING . . . . . . . . . . . . . . . . .30  
NORMAL RECORDING . . . . . . . .30  
CONNECTING TO EXTERNAL  
INPUT JACKS . . . . . . . . . . . . . . . .12  
SKIPPING UNWANTED SCENES  
DURING RECORDING . . . . . . . . .30  
INSTALLING THE BATTERIES . .12  
EXTERNAL INPUT MODE . . . . . .12  
OTR (One Touch Recording) . . . . . .31  
COPYING A VIDEO CASSETTE  
(Requires a VCR or camcorder) . . .31  
C
THE ON-SCREEN INFORMATION . . .43  
CONNECTING TO A STEREO  
AMPLIFIER EQUIPPED WITH DIGI-  
TAL INPUT JACKS SUCH AS MD  
DECK OR DAT DECK (for DVD) .13  
C CHANGING THE DVD SETUP  
C TIMER . . . . . . . . . . . . . . . . . . . . . .32  
ITEMS . . . . . . . . . . . . . . . . . . . . . . .44  
AUTOMATIC  
TIMER RECORDING . . . . . . . . . .32  
LANGUAGE SETTING . . . . . . . . .44  
DISPLAY SETTING . . . . . . . . . . . .45  
AUDIO SETTINGS . . . . . . . . . . . .45  
PARENTAL CONTROL . . . . . . . . .46  
INITIALIZE . . . . . . . . . . . . . . . . . .46  
CONNECTING TO A DOLBY  
DIGITAL DECODER (for DVD) . .14  
TIMER PROGRAM EXTENSION .33  
TV/VCR SECTION  
HINTS FOR AUTOMATIC TIMER  
RECORDING . . . . . . . . . . . . . . . . .34  
C SET UP FOR USE . . . . . . . . . . . . .15  
AUTO RETURN . . . . . . . . . . . . . . .34  
SLEEP TIMER . . . . . . . . . . . . . . . .34  
SELECTING THE LANGUAGE . .15  
C TROUBLESHOOTING GUIDE . . .47  
CLOCK SET UP  
(AUTO / MANUAL) . . . . . . . . . . . .15  
C ON SCREEN DISPLAY . . . . . . . . .35  
C MAINTENANCE . . . . . . . . . . . . . . .50  
DAYLIGHT-SAVING TIME . . . . . .17  
CHANNEL SET UP . . . . . . . . . . . .18  
DISC HANDLING . . . . . . . . . . . . .50  
C CABLE CHANNEL  
DESIGNATIONS . . . . . . . . . . . . . .35  
C SPECIFICATIONS . . . . . . . . . . . . .51  
C ESPAÑOL . . . . . . . . . . . . . . . . . . . .52  
C WARRANTY . . . . . . . . . . .Back Cover  
DELETING (OR ADDING)  
CHANNEL(S) . . . . . . . . . . . . . . . . .18  
DVD SECTION  
C TV OPERATION . . . . . . . . . . . . . . .19  
WATCHING A TV PROGRAM . . .19  
DEGAUSSING . . . . . . . . . . . . . . . .19  
PICTURE CONTROL . . . . . . . . . . .19  
CLOSED CAPTION SYSTEM . . . .20  
V-CHIP SET UP . . . . . . . . . . . . . . .21  
C ABOUT THE DISCS . . . . . . . . . . . .36  
PLAYABLE DISCS . . . . . . . . . . . .36  
DISC TYPES . . . . . . . . . . . . . . . . .36  
C PLAYING A DISC . . . . . . . . . . . . . .37  
BASIC PLAYBACK . . . . . . . . . . . .37  
GENERAL FEATURES . . . . . . . . .37  
DISC MENU . . . . . . . . . . . . . . . . .37  
TITLE MENU . . . . . . . . . . . . . . . . .37  
RESUME . . . . . . . . . . . . . . . . . . . .38  
PAUSE . . . . . . . . . . . . . . . . . . . . . .38  
STEP BY STEP PLAYBACK . . . . .38  
C MTS(Multi-Channel Television  
sound)SYSTEM . . . . . . . . . . . . . . . .23  
CHECKING THE SELECTED  
MTS MODE . . . . . . . . . . . . . . . . . .23  
MTS RECORDING/MONITOR  
MODE . . . . . . . . . . . . . . . . . . . . . .23  
SELECTING THE MTS SYSTEM .24  
FAST FORWARD/REVERSE  
SEARCH . . . . . . . . . . . . . . . . . . . .38  
C VIDEO CASSETTE . . . . . . . . . . . . .25  
SLOW FORWARD / SLOW  
REVERSE . . . . . . . . . . . . . . . . . . . .38  
C PLAYBACK . . . . . . . . . . . . . . . . . . .26  
NORMAL PLAYBACK . . . . . . . . .26  
TRACKING ADJUSTMENT . . . . .26  
SLOW MOTION . . . . . . . . . . . . . .26  
C SEARCH FUNCTION . . . . . . . . . . .39  
TRACK SEARCH . . . . . . . . . . . . .39  
TITLE / CHAPTER SEARCH . . . .39  
- 6 -  
EN  
1C29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FEATURES  
TV/VCR Mode  
Hi-Fi systemThe Hi-Fi stereo recording system  
offers you excellent sound quality with a dynamic  
range of 80dB, frequency response from 20Hz to  
20kHz and 0.005% wow and flutter.  
Rotary 4-head Record/Playback System–Four heads  
ensure excellent picture quality and special effects playback.  
Index Search–Fast-forwards to start of next recording.  
Slow Motion–View recorded program at slower  
than normal speed.  
Infrared remote control  
Trilingual on screen TV/VCR setup display  
selectable in English or Spanish or French  
Real time counter–This shows the elapsed recording  
or playback time in hours, minutes and seconds. The  
“–” indication will appear when the tape is rewound  
further than the tape counter position “0:00:00”.  
181 channel capability PLL frequency synthesiz-  
er tuner with direct station call–(A converter may  
be necessary to view scrambled cable channels.)  
Auto Clock Setting–Allows you to set the clock  
function from a PBS broadcast station.  
Closed caption system–You may view specially  
labeled (cc) TV programs, movies, news, prere-  
corded tapes, etc. with either a dialogue caption or  
text display added to the program.  
Auto power on and off system–Automatically  
turns on the TV/VCR/DVD when you insert the  
cassette, turns off after auto-rewind and ejects  
when the beginning of the tape is reached.  
Auto rewind when the end of a tape is  
reached–This function doesn’t occur when using  
timer recording.  
2 Step picture search operation–You can view a  
video program at a high speed or super high speed  
in either a forward or reverse direction in LP and  
SLP mode. For SP mode only high speed.  
Three different playback tape speeds : SP/LP/SLP  
Two different recording tape speeds : SP/SLP  
Auto Head Cleaner–Automatically cleans video  
heads as you insert or remove a cassette.  
Zero Return–The tape returns to counter of  
0:00:00 by rewinding or fast forwarding.  
Still–“Freeze” the picture at any time, for close  
viewing of a particular scene.  
Digital Auto Tracking (DTR)–Automatically  
adjusts the tracking for each tape you play.  
Rental play mode–Improves playback picture  
quality from worn tapes, such as rental tapes.  
Auto repeat–Allows you to repeat the playing of a  
tape indefinitely without pressing the PLAY button.  
Time search–Lets you set the TV/VCR/DVD to  
advance the tape by entering the desired playback  
time you want to skip.  
OTR (One Touch Recording)–Instant timed  
recording from 30 to 480 minutes is possible at the  
push of the REC/OTR button.  
1 Year, 8 events (including Daily and Weekly  
Timer Recording)–The built-in timer allows you to  
record up to 8 programs at different times on dif-  
ferent channels up to 1 year in advance. The Daily  
timer allows recordings to be made of daily broad-  
casts and the Weekly timer allows recording to be  
made once a week up to the end of the tape.  
Auto return–After timer recording is finished, the  
TV/VCR/DVD can return to the beginning of the  
recording.  
Smooth mode change–TV/VCR mode DVD  
mode automatically changes without control.  
Sleep timer–Allows you to have the TV/VCR/DVD  
automatically turn off at a desired time.  
Timer Program Extension–Allows you to shift the  
time schedule for automatic timer recording.  
V-CHIP–Enables parents to prevent their children  
from watching inappropriate material on TV.  
- 7 -  
EN  
1C29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DVD Mode  
¡Playback MP3 disc  
¡Dolby Digital sound  
¡On-screen display  
This TV/VCR/DVD can handle Dolby Digital sur-  
round sound having 5.1 channels when connected to  
a Dolby Digital decoder.  
Information about the current operation can be dis-  
played on a TV screen, allowing you to confirm the  
currently active functions (such as program play-  
back), on the TV screen using the remote control.  
¡Still/fast/slow/step playback  
Various playback modes are available including still  
pictures, fast forward/reverse, slow motion and step  
frames.  
¡Search  
Chapter search / Title search / Track search / Time  
search  
¡Random playback for audio CD and MP3  
This TV/VCR/DVD can shuffle the order of tracks  
to play them in random order.  
¡Repeat  
Chapter / Title / Track / Group / All / A-B  
¡Program playback for audio CD and MP3  
You can program the order of tracks to play them in  
any desired order.  
¡Marker  
The part designated by user can be called back.  
¡Resume Play  
User can resume to playback from the part at which  
the play was stopped.  
¡Virtual Surround  
¡Bit rate indication  
¡DVD menus in a desired language  
You can display DVD menus in a desired language,  
if available on a DVD.  
¡Screen saver/Auto power-off functions  
The screen saver program starts when there is no  
input from the TV/VCR/DVD for five minutes in the  
stop mode. When the screen saver program is acti-  
vated for 15 minutes, the power automatically turns  
off.  
¡DRC (Dynamic range control)  
You can control the range of sound volume.  
¡Subtitles in a desired language  
You can select a desired language for the display  
subtitles, if that language is available on a disc.  
¡Selecting a camera angle  
You can select the desired camera angle, if a disc  
contains sequences recorded from different angles.  
¡Choices for audio language and sound mode  
You can select the desired audio language and sound  
mode, if different languages and modes are available  
on a disc.  
¡Parental lock  
You can set the control level to limit playback of  
discs which may not be suitable for children.  
¡Automatic detection of discs  
This TV/VCR/DVD automatically detects if the  
loaded disc is DVD, audio CD or MP3 on disc.  
NOTE:  
We do not recommend the use of universal remote controls. Not all of the functions may be controlled with  
a universal remote control.  
If you decide to use a universal remote control with this TV/VCR/DVD, please be aware that the code num-  
ber given may not operate this TV/VCR/DVD. In this case, please call the manufacturer of the universal  
remote control.  
- 8 -  
EN  
1C29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATING CONTROLS AND FUNCTIONS  
- TV/VCR/DVD FRONT PANEL - [Fig.1]  
DVD buttons  
TV/VCR buttons  
F.FWD  
PLAY  
REW  
REC/OTR  
STOP/EJECT  
POWER  
VOLUME  
OPEN/CLOSE  
SELECT  
SKIP  
PLAY  
SKIP  
STOP  
CHANNEL  
L
AUDIO  
R
HEADPHONE  
VIDEO  
DVD  
TV/VCR  
SEARCH  
2
3 4  
3
5
6
7
10 11 12 13 14 4 15 16 17 18 19 20  
21  
8 9  
1
5.STOP Button [TV/VCR P.26 / DVD P.37]  
[Fig. 2]  
- REMOTE CONTROL -  
Stops operation of the disc. (or front panel)  
Stops operation of the disc or tape contents.  
(remote control)  
6.OPEN/CLOSE Button [DVD P.37]  
Press to insert discs into or remove them from the  
tray.  
7.Disc loading tray  
8.DVD Indicator  
Lights on during DVD mode.  
9.SELECT Button  
Press to change to TV/VCR mode, external input  
mode or DVD mode.  
10.TV/VCR Indicator  
Lights on during TV/VCR mode.  
11. CHANNEL (CH.) K/L Buttons  
Press to select memorized channel.  
12. Recording Indicator  
Flashes during recording. Lights up in the Stand-  
by mode for Timer Recording.  
13. REC/OTR Button (Front Panel) [TV/VCR P.30, 31]  
Press to start manual recording. Press repeatedly  
to start One Touch Recording.  
RECORD Button (Remote Control) [TV/VCR P.30]  
Press to start manual recording.  
14. REW Button (for TV/VCR) [TV/VCR P.26]  
Press to rewind the tape, or to view the picture  
rapidly in reverse during playback mode. (Rewind  
Search)  
POWER PICTURE SLEEP SELECT  
1
45  
44  
11  
22  
1
4
2
5
8
0
3
6
CH.  
23  
7
PAUSE  
9
+100  
VOL.  
2
+10  
24  
25  
26  
SPEED C.RESET  
V.SURR  
MUTE  
43  
42  
PLAY  
STOP  
3 (DVD)  
15 (TV/VCR)  
5
41  
(DVD) 3  
(TV/VCR) 414  
DISC  
MENU  
RECORD  
13  
DISPLAY  
SETUP  
40  
ENTER  
27  
TITLE  
RETURN  
39  
38  
37  
28  
29  
30  
CLEAR SEARCH MODE REPEAT  
A-B  
AUDIO SUBTITLE ANGLE  
MODE  
31  
32  
33  
36  
35  
34  
15. F.FWD Button (for TV/VCR) [TV/VCR P.26]  
Press to rapidly advance the tape, or to view the  
picture rapidly in forward during playback mode.  
(Forward Search)  
1.POWER Button [TV/VCR P.15 / DVD P.37]  
Press to turn the power on and off.  
16. STOP/EJECT Button [TV/VCR P.28]  
2.VOLUME (VOL.) X/Y Buttons  
Press to stop the tape motion. Press in the Stop  
mode to remove tape from the TV/VCR/DVD.  
Press to control the volume level for the DVD and TV.  
3.SKIP (SEARCH) Buttons (for DVD)[P.38]  
Press once to skip chapters or tracks to a desired  
point.  
Press and hold to change forward or reverse play-  
back speed.  
17. Remote sensor window  
18. HEADPHONE Jack  
To connect headphone (not supplied) for personal  
listening.  
19. VIDEO input Jack  
4.PLAY Button [TV/VCR P.26 / DVD P.37]  
Connect to the video output jack of a video  
camera or VCR.  
Starts playback of the disc or tape contents.  
- 9 -  
EN  
1C29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
- TV/VCR/DVD REAR PANEL - [Fig.3]  
ANT.  
AUDIO OUT  
COAXIAL  
46  
47  
48  
20. AUDIO L/R input Jacks  
31. MODE Button [DVD P.41]  
Connect to the audio output jacks of a video  
camera or VCR.  
Activates program playback or random playback mode.  
32. SEARCH MODE Button [DVD P.39]  
21. Cassette compartment  
Press to locate a desired point.  
22. PICTURE Button  
33. AUDIO Button [DVD P.42]  
Press to select a desired audio language or sound  
mode.  
Press to adjust the picture.  
23. Number Buttons  
34. SUBTITLE Button [DVD P.42]  
TV Mode:[P.15]  
Press two digits to directly access the desired  
channel.  
Remember to press a "0" before a single digit  
channel.  
+100 Button–  
Press to select cable channels which are equal or  
greater than number 100.  
DVD Mode:  
Press to enter the desired number.  
+10 Button–  
Press to enter the desired numbers which are  
equal or greater than number 10.  
Press to select a desired subtitle language.  
35. REPEAT Button [DVD P.42]  
Repeats playback of the current disc, title, chapter  
or track.  
36. ANGLE Button (DVD mode) [DVD P.42]  
Press to change the camera angle to see the  
sequence being played back from a different angle.  
37. A-B REPEAT Button [DVD P.40]  
Repeats playback of a selected section.  
38. RETURN Button  
Returns to the previous operation in the DVD  
setup mode.  
24. PAUSE Button [TV/VCR P.26 / DVD P.38]  
39. ENTER Button  
Pauses the current disc or tape operation.  
Press to accept a setting.  
25. SPEED Button [TV/VCR P.30]  
Press to choose the desired recording speed:  
SP/SLP.  
26. C.RESET Button [TV/VCR P.28]  
Press to reset counter to 0:00:00.  
Press to cancel a setting of timer program. (See  
page 33.)  
40. Arrow Buttons  
TV/VCR Mode:  
Press to select a setting mode from the menu on  
the TV screen.  
Press to select or adjust from a particular menu.  
DVD Mode:  
Use when making settings while watching the  
display on a TV screen.  
27. DISPLAY Button  
TV/VCR Mode:  
41. DISC MENU Button [DVD P.37]  
Display the counter or the current channel number  
and current time on the TV screen.  
DVD Mode:[P.43]  
Displays the current status on the TV screen for  
checking purposes.  
Displays the menus in the DVD.  
42. V. SURR (VIRTUAL SURROUND) Button [DVD P.42]  
Sets virtual surround on/off.  
43. MUTE Button  
Mutes the sound. Press it again to resume sound.  
28. SETUP Button [TV/VCR P.15] [DVD P.44-46]  
Press to enter or exit the TV menu or DVD setup  
mode.  
44. SLEEP Button [TV/VCR P.34]  
Sets the Sleep Timer.  
45. SELECT Button  
29. TITLE Button [DVD P.37]  
Press to switch TV/VCR and DVD mode. You can  
see the mode (TV/VCR or DVD) on the front  
panel indicator.  
Displays the title menu.  
30. CLEAR Button  
Resets a setting.  
- 10 -  
EN  
1C29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
46. ANT. in Jack  
48. COAXIAL digital audio out Jack  
Connect to the digital input of an external  
amplifier or decoder for DVD audio only.  
Connect to an antenna, cable system, or satellite  
system.  
47. Power cord  
Connect to a standard AC outlet (120V/60Hz).  
NOTE: Remove the power cord from the hook to  
avoid breaking a wire before you connect  
to a standard AC outlet.  
PREPARATION FOR USE  
ANTENNA/CABLE CONNECTION  
VHF/UHF Antenna  
(Not supplied)  
Satellite Box or  
Cable Box (Not supplied)  
OUT  
IN  
From Cable System or  
Satellite Dish  
VHF Antenna (Not supplied)  
75-ohm  
Coaxial  
Cable  
UHF Antenna  
(Not supplied)  
From Cable  
System  
(Not sup-  
plied)  
or  
VHF/UHF  
A
N
T
.
A
U
D
I
O
O
U
T
COAXIAL  
Combiner  
(Not supplied)  
ANT.  
75-ohm Coaxial  
Cable (Not  
supplied)  
or  
[Fig. 4]  
Flat twin-lead cable  
or  
VHF/UHF SEPARATE ANTENNAS  
CABLE WITH CONVERTER/  
DESCRAMBLER BOX OR SATELLITE  
BOX  
In some areas it will be necessary to use an outdoor  
antenna.  
If your cable service supplies you with a converter  
box or if you use a satellite system, you can use the  
basic connection shown in the illustration.  
CABLE WITHOUT CONVERTER/  
DESCRAMBLER BOX  
By using this connection you can also record scram-  
bled channels. However, channel selection must be  
made with the converter box or satellite box. This  
means that channels cannot be changed using the  
TV/VCR/DVD Remote Control. Unattended timer  
recording is limited to one channel at a time.  
Use this connection if your cable system connects  
directly to your TV/VCR/DVD without a converter  
box.  
By using this connection you can:  
1) Use the TV/VCR/DVD remote to select channels.  
2) Program one or more unscrambled channels for  
Automatic Timer Recording.  
Antenna/Cable Connections  
Continued on the Next Page.  
NOTE: This TV/VCR/DVD will ONLY record and  
view the same channel.  
- 11 -  
EN  
1C29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TO RECORD A SCRAMBLED/UNSCRAM-  
BLED CHANNEL  
INSTALLING THE BATTERIES  
1. Set the TV/VCR/DVD channel selector to the out-  
put channel of the Cable Converter Box or Satellite  
Box. (Ex. CH3)  
1)Open the battery compartment cover by pressing  
the cover on the remote unit in the direction of the  
arrow.  
2.Select the channel to record from your Cable  
Converter Box or Satellite Box.  
2)Insert 2 “AA” penlight batteries into the battery  
compartment in the direction indicated by the  
polarity (+/-) markings.  
Note to CATV system installer:  
3)Replace the cover.  
This reminder is provided to call the CATV sys-  
tem installer’s attention to Article 820-40 of the  
NEC that provides guidelines for proper ground-  
ing and in particular, specifies that the cable  
ground shall be connected to the grounding sys-  
tem of the building as close to the point of cable  
entry as practical.  
EXTERNAL INPUT MODE  
When using an external input signal (another VCR or  
video camera), connect the player’s audio/video out-  
put cables to the AUDIO L/R IN/  
CONNECTING TO EXTERNAL  
INPUT JACKS  
When you watch a program recorded on an another  
source (VCR or video camera), use the audio/video  
input jacks on the front of the TV/VCR/DVD.  
Connect the audio/video output jacks of another  
source to the AUDIO L/R and VIDEO jacks of this  
TV/VCR/DVD.  
AUX  
VIDEO IN jacks of your  
TV/VCR/DVD. Then press the  
CHANNEL button K or L until  
“AUX” appears on the screen.  
Then press the CHANNEL button K or L until  
"AUX" appears on the screen.  
NOTE:  
When you connect a monaural VCR (another  
source) to this TV/VCR/DVD, connect the Audio  
output jack of the monaural VCR (another source)  
to the AUDIO L jack of this TV/VCR/DVD. The  
audio will output in both L and R channel equally.  
To the audio  
output jacks  
[Another source]  
HEADPHONE  
VIDEO  
L-AUDIO-R  
Audio/Video  
coaxial cable  
(not supplied)  
etc.  
To the video  
[Front of the  
TV/VCR/DVD]  
output jack  
[Fig. 5]  
- 12 -  
EN  
1C29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONNECTING TO A STEREO AMPLIFIER EQUIPPED WITH DIGI-  
TAL INPUT JACKS SUCH AS MD DECK OR DAT DECK (for DVD)  
Use an audio coaxial digital cable available at retail for the audio connections.  
Connecting to an amplifier equipped with digital input jacks such as MD Deck or DAT Deck.  
ANT.  
AUDIO OUT  
COAXIAL  
Amplifier equipped with digital  
input jacks, MD deck,  
DAT deck, etc.  
To DIGITAL AUDIO OUT  
(PCM/BITSTREAM)  
COAXIAL jack  
To COAXIAL DIGITAL  
AUDIO INPUT jack  
(only DVD AUDIO OUT)  
[Fig. 6]  
NOTES:  
The audio source on a disc in a 5.1 channel Dolby Digital surround format cannot be recorded as digital  
sound by an MD or DAT deck.  
Be sure to turn off the power to all components in the system before connecting another component.  
Refer to the Owner's Manuals for the components to be connected to the TV/VCR/DVD.  
Set Dolby Digital to OFF for audio output in the setup mode. Playing a TV/VCR/DVD using incorrect set-  
tings may generate noise distortion and may also damage the speakers.  
- 13 -  
EN  
1C29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONNECTING TO A DOLBY DIGITAL DECODER (for DVD)  
If using this TV/VCR/DVD to play a DVD disc in a 5.1 channel Dolby Digital surround format, the  
TV/VCR/DVD outputs a DOLBY DIGITAL Data stream from its COAXIAL digital audio out jack. By hook-  
ing the TV/VCR/DVD up to a Dolby Digital decoder, you can enjoy a more convincing, realistic ambience  
with powerful and high-quality surround sound as enjoyed in movie theaters.  
Use audio coaxial digital cables available at retail for the audio connections.  
Center  
speaker  
Front speaker  
(left)  
Front speaker  
(right)  
ANT.  
AUDIO OUT  
COAXIAL  
To DIGITAL AUDIO OUT  
(PCM/BITSTREAM)  
COAXIAL jack  
Dolby Digital  
decoder  
To COAXIAL DIGITAL  
AUDIO INPUT jack  
Subwoofer  
Surround  
speaker  
(left)  
Surround  
speaker  
(right)  
[Fig. 7]  
NOTES:  
Be sure to turn off the power to all components in the system before connecting another component.  
Refer to the Owner's Manuals for the components to be connected to the TV/VCR/DVD.  
If connected to a Dolby Digital decoder, set DOLBY DIGITAL to ON for audio output in the setup mode.  
(See page 45 to set DOLBY DIGITAL to ON.)  
Unless connected to a Dolby Digital decoder, set DOLBY DIGITAL to OFF for audio output in the setup  
mode. Playing a TV/VCR/DVD using incorrect settings may generate noise distortion and may also damage  
the speakers.  
Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are  
trademarks of Dolby Laboratories.  
- 14 -  
EN  
1C29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TV/VCR SECTION  
SET UP FOR USE  
SELECTING THE LANGUAGE  
CLOCK SET UP  
(AUTO / MANUAL)  
TV/VCR  
TV/VCR  
1 Plug in the TV/VCR/DVD power cord  
Plug the TV/VCR/DVD power cord into a  
standard AC outlet.  
The TV/VCR/DVD clock must be set correctly before  
VCR timer recording is possible. It is suggested that  
the clock be set manually when first setting up the  
TV/VCR/DVD, then set to [ON] the auto clock set-  
ting which will periodically correct the setting if nec-  
essary.  
NOTE: If you cannot receive a station with time  
signals, auto clock setting cannot be performed. Use  
manual setting only.  
NOTE:  
If any digits appear in the corner of the  
screen, press the POWER button without unplug-  
ging the power cord.  
Make sure ...  
Press the SELECT button to select TV/VCR mode or  
make sure TV/VCR lights on.  
MANUAL CLOCK SETTING  
Press the POWER button to turn on the TV/VCR/DVD.  
NOTE: This function effects only the language on  
the screen menu and not the audio source.  
Make sure ...  
The TV/VCR/DVD is turned on.  
In the example below, the clock is to be set to:  
– M E N U –  
DATE  
May 6th, 2004  
2 Select “LANGUAGE”  
Press the SETUP button on the  
TIMER PROGRAMMING  
PICTURE CONTROL  
SETTING CLOCK  
CHANNEL SET UP  
USER’S SET UP  
V-CHIP SET UP  
SETTING TIME 5:40PM  
remote control.  
Press the Arrow button K or L to  
point to “LANGUAGE”.  
B
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
1 Select “SETTING CLOCK”  
Press the SETUP button on the  
remote control.  
Press the Arrow button K or L to  
point to “SETTING CLOCK”.  
Then press the ENTER button.  
– M E N U –  
TIME SEARCH  
TIMER PROGRAMMING  
PICTURE CONTROL  
SETTING CLOCK  
CHANNEL SET UP  
USER’S SET UP  
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
B
3 Select “ENGLISH”, “ESPAÑOLor “FRANÇAIS”  
Select “ENGLISH”, “ESPAÑOL”= Spanish or  
“FRANÇAIS”= French using the ENTER button.  
ZERO RETURN  
TIME SEARCH  
2 Select “MANUAL CLOCK SET”  
Press the Arrow button K or L to  
point to “MANUAL CLOCK  
SET”.  
4 Exit the Language mode  
– SETTING CLOCK –  
Press the SETUP button on the remote control to  
return to TV mode.  
AUTO CLOCK  
[ON]  
AUTO CLOCK CH SEARCH  
AUTO CLOCK CH  
MANUAL CLOCK SET  
D.S.T.  
[ 02 ]  
B
[OFF]  
NOTE: If for some reason the menu is in Spanish or  
French, press the SETUP button on the remote control,  
press the Arrow button K or L to point to “IDIOMA  
[ESPAÑOL]” or “LANGAGE [FRANÇAIS]”, then  
press the ENTER button, then press the SETUP button  
on the remote control.  
Then press the ENTER button.  
3 Select the month  
Press the Arrow button K or  
– MANUAL CLOCK SET –  
MONTH DAY YEAR  
L
until your desired month appears.  
0 5  
/
– – – – – – – – –  
(Example: May 05)  
HOUR  
– –  
MINUTE  
– – – –  
Then press the Arrow button B.  
(Or press the Arrow button { to  
go back one step.)  
:
– MANUAL CLOCK SET –  
MONTH DAY YEAR  
4 Select the day  
Press the Arrow button K or  
L
0 5  
/
0 6 – – – – – – –  
until your desired day appears.  
(Example: 6th 06)  
HOUR  
– –  
MINUTE  
– – – –  
:
Then press the Arrow button B.  
- 15 -  
EN  
1C29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AUTOMATIC CLOCK SETTING  
Make sure ...  
5 Select the year  
– MANUAL CLOCK SET –  
MONTH DAY YEAR  
The TV/VCR/DVD is turned on.  
Confirm the TV/VCR/DVD is receiving a RF  
Press the Arrow button K or  
L
0 5  
/
0 6 THU 2 0 0 4  
until your desired year appears.  
(Example: 2004)  
Then press the Arrow button B.  
(Radio Frequency) signal from either an antenna or  
cable system connection using the ANT. terminal  
on the rear of the TV/VCR/DVD.  
NOTE:  
HOUR  
– –  
MINUTE  
– – – –  
:
If a cable converter box is being used, make sure it  
is powered on.  
You must use the TV/VCR/DVD remote control to  
perform the clock setting procedure.  
6 Select the hour  
– MANUAL CLOCK SET –  
MONTH DAY YEAR  
Press the Arrow button K or  
L
0 5  
/
0 6 THU 2 0 0 4  
until your desired hour appears.  
(Example: 5, PM)  
Then press the Arrow button B.  
HOUR  
0 5  
MINUTE  
– – PM  
:
If the TV/VCR/DVD is connected directly to a  
cable converter box or satellite box, the local PBS  
station must be selected on the cable box itself and  
the TV/VCR/DVD must be set to the output chan-  
nel of the cable converter box or satellite box (usu-  
ally channel 3 or 4), to be able to set up or correct  
the clock automatically.  
– MANUAL CLOCK SET –  
MONTH DAY YEAR  
7 Select the minute  
Press the Arrow button K or  
until the desired minute appears.  
(Example: 40)  
L
0 5  
/
0 6 THU 2 0 0 4  
HOUR  
0 5  
MINUTE  
4 0 PM  
:
1 Select “SETTING CLOCK”  
– M E N U –  
8 Start the clock  
TIMER PROGRAMMING  
PICTURE CONTROL  
SETTING CLOCK  
CHANNEL SET UP  
USER’S SET UP  
V-CHIP SET UP  
Press the SETUP button on the  
5:40 PM  
B
Press the SETUP button on the  
remote control.  
remote control.  
Press the Arrow button K or L to  
select “SETTING CLOCK”.  
Press the ENTER button to enter  
“SETTING CLOCK” menu.  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
Although seconds are not displayed,  
they begin counting from 00 when  
you press the SETUP button on the  
remote control. Use this feature to synchronize the  
clock with the correct time.  
TIME SEARCH  
2 Set “AUTO CLOCK” to [ON]  
Press the Arrow button B until  
“AUTO CLOCK [ON]” appears.  
– SETTING CLOCK –  
NOTE:  
B
AUTO CLOCK  
AUTO CLOCK CH SEARCH  
AUTO CLOCK CH  
MANUAL CLOCK SET  
D.S.T.  
[ON]  
When unplugging the AC cord or if there is a power  
failure for more than 3 seconds, you may have to  
reset the clock.  
[ 02 ]  
[OFF]  
TO CHANGE CLOCK SETTING  
If you want to change the clock,  
1) Follow steps [1] and [2].  
2) Select where you want to change using the Arrow  
button B.  
3) Enter correct numbers using the Arrow button  
3 Begin “AUTO CLOCK CH SEARCH”  
Press the Arrow button K or L to  
– SETTING CLOCK –  
select “AUTO CLOCK CH  
SEARCH”.  
AUTO CLOCK  
[ON]  
B
AUTO CLOCK CH SEARCH  
AUTO CLOCK CH  
MANUAL CLOCK SET  
D.S.T.  
[ 02 ]  
[OFF]  
Press the ENTER button.  
The TV/VCR/DVD is now  
searching for the station which contain the auto  
clock set signal. The search for a signal may take  
up to 20 seconds per channel.  
K
or L.  
4) Press the SETUP button on the remote control to  
start the clock.  
“_ _” appears at the lower left of  
the screen when the search has  
ended.  
Auto Clock station- write down  
the number(s) that appear on the  
screen. These are the auto clock  
– AUTO CLOCK CH SEARCH –  
PLEASE NOTE:  
08  
10  
13  
If there is no local PBS station in your area or on  
your cable system, select “AUTO CLOCK” and  
press the ENTER button to turn [OFF] this function.  
Then you can manually adjust the clock.  
_ _  
station(s) in your area. See step [4] on page 17.  
If no number(s) appear on the TV screen, there are  
no stations in your area which contain the Auto  
Clock signal. Auto Clock Setting is not possible.  
Please use Manual Clock Setting on page 15.  
Press the SETUP button to exit the screen.  
- 16 -  
EN  
1C29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NOTE: During Auto Clock CH Search, the picture  
may be distorted, this is normal.  
DAYLIGHT-SAVING TIME  
TV/VCR  
4 Enter the channel number that contains the  
Automatic Clock Setting Signal  
Press the SETUP button on the remote control.  
Select this feature and the TV/VCR/DVD’s clock  
automatically will advance one hour in April, then  
reverse one hour in October.  
Press the Arrow button K or L to  
select “SETTING CLOCK”.  
When Daylight-Saving Time is ON, the clock will  
change automatically as follows:  
– M E N U –  
TIMER PROGRAMMING  
PICTURE CONTROL  
SETTING CLOCK  
CHANNEL SET UP  
USER’S SET UP  
V-CHIP SET UP  
B
Press the ENTER button to enter  
“SETTING CLOCK” menu.  
Press the Arrow button K or L to  
select “AUTO CLOCK CH”.  
Press the ENTER button or the  
Arrow button { or B until you  
locate Auto Clock Set station num-  
ber. See step [3] on page 16.  
Press the SETUP button to exit the  
screen.  
First Sunday of April : At 2 AM the clock imme-  
diately changes to 3 AM. Any timer programming  
you have set to occur between 2 AM and 3 AM  
will not record.  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
TIME SEARCH  
– SETTING CLOCK –  
Last Sunday of October : At 2 AM the clock  
immediately changes to 1 AM.  
AUTO CLOCK  
AUTO CLOCK CH SEARCH  
AUTO CLOCK CH  
MANUAL CLOCK SET  
D.S.T.  
[ON]  
B
[
45]  
Make sure ...  
[OFF]  
Press the POWER button to turn on the TV/VCR/DVD.  
1 Select “SETTING CLOCK”  
– M E N U –  
Press the SETUP button on the  
TIMER PROGRAMMING  
PICTURE CONTROL  
5 Turn off the TV/VCR/DVD  
Once the TV/VCR/DVD is turned off , it will period-  
ically check and set the correct date and time.  
remote control.  
B
SETTING CLOCK  
CHANNEL SET UP  
USER’S SET UP  
V-CHIP SET UP  
Press the Arrow button K or L to  
point to “SETTING CLOCK”.  
Then press the ENTER button.  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
TIME SEARCH  
2 Set “D.S.T.(Daylight-Saving Time) to [ON]  
Press the Arrow button K or L to  
– SETTING CLOCK –  
point to “D.S.T.”.  
Then press the ENTER button until  
[ON] appears.  
AUTO CLOCK  
[ON]  
AUTO CLOCK CH SEARCH  
AUTO CLOCK CH  
MANUAL CLOCK SET  
D.S.T.  
[ 02 ]  
B
[ON]  
3 Exit the Daylight-Saving Time mode  
Press the SETUP button on the remote control to  
return to TV mode.  
TO CANCEL THE DAYLIGHT-SAVING  
TIME  
Repeat steps [1] to [2], select [OFF] using the  
ENTER button.  
- 17 -  
EN  
1C29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DELETING (OR ADDING)  
CHANNEL(S)  
CHANNEL SET UP  
TV/VCR  
TV/VCR  
You can program the tuner to scan all the channels  
you receive in your area.  
The channels you no longer receive or seldom watch  
can be deleted from the memory. (Of course, you  
can add the deleted channel into the memory again.)  
NOTE: Channel memory programming is NOT  
needed when connected to a cable box or satellite  
box. Just select the TV/VCR/DVD channel selector  
to the output channel of the cable box or satellite box  
(Ex CH3), then select the channel to be viewed on  
the Cable Box or Satellite Box.  
1 Select “CHANNEL SET UP”  
– M E N U –  
Press the SETUP button on the  
TIMER PROGRAMMING  
PICTURE CONTROL  
remote control.  
SETTING CLOCK  
B
CHANNEL SET UP  
USER’S SET UP  
V-CHIP SET UP  
Press the Arrow button K or L to  
point to “CHANNEL SET UP”.  
Then press the ENTER button.  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
Make sure ...  
Press the POWER button to turn on the TV/VCR/DVD.  
TIME SEARCH  
1 Select “CHANNEL SET UP”  
2 Select “ADD/DELETE CH”  
Press the Arrow button K or L to  
point to “ADD/DELETE CH”.  
Press the ENTER button.  
– CHANNEL SET UP –  
– M E N U –  
Press the SETUP button on the  
B
ADD / DELETE CH (CATV)  
AUTO CH PROGRAMMING  
TIMER PROGRAMMING  
PICTURE CONTROL  
remote control.  
SETTING CLOCK  
B
CHANNEL SET UP  
USER’S SET UP  
V-CHIP SET UP  
Press the Arrow button K or L to  
point to “CHANNEL SET UP”.  
Then press the ENTER button.  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
TIME SEARCH  
3 Enter the desired channel number  
Press the Arrow button K or  
until your desired channel number  
appears. (You can also use the  
number buttons or the CHANNEL  
button K or L to enter it)  
2 Begin auto ch programming  
Press the Arrow button K or L to  
point to “AUTO CH PROGRAM-  
MING”.  
Then press the ENTER button.  
The tuner scans and memorizes all  
the active channels in your area.  
L
– CHANNEL SET UP –  
ADD / DELETE CH (CATV)  
AUTO CH PROGRAMMING  
08  
B
ADD / DELETE  
(Example: CH8)  
You must precede single-digit channel numbers  
with a zero (Example: 02 ... 09).  
When selecting cable channels which are higher  
than 99, press the +100 button first, then press the  
last two digits. (Example: to select channel 125,  
first press the +100 button then press “2” and “5”).  
3 After scanning  
The tuner stops on the lowest memorized channel.  
When AUTO CH PROGRAMMING is activated  
where there is no TV signal input, “NO TV SIG-  
NALS” will appear on the display after the com-  
pletion of the channel scanning.  
4 Delete (or add) it from (into) memory  
Press the ENTER button. The channel number  
changes to light red. The channel is deleted from  
memory.  
To delete another channel, repeat steps [3] and [4].  
If you press the ENTER button again, the channel  
The TV/VCR/DVD may recognize TV channels to  
be CATV channels by the receiving conditions. In  
this case, try auto ch programming again in the fine  
receiving conditions.  
is memorized again.  
Added channel: Light blue.  
Deleted channel: Light red.  
5 Exit the channel setup mode  
Press the SETUP button on the remote control to  
return to TV mode.  
NOTE: To confirm that channel(s) has been deleted  
or added, press the CHANNEL button K or L.  
- 18 -  
EN  
1C29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TV OPERATION  
WATCHING A TV PROGRAM  
PICTURE CONTROL  
TV/VCR  
TV/VCR  
The TV/VCR/DVD’s picture controls – BRIGHT,  
CONTRAST, COLOR, TINT and SHARPNESS –  
are preset to factory specifications. Although they are  
usually the best, you may need to make some further  
adjustments for a more natural looking image.  
1 Turn on the TV/VCR/DVD  
Press the POWER button to turn on the  
TV/VCR/DVD.  
NOTES:  
2 Select the channel number  
Press the CHANNEL button K or L to select your  
desired channel number or press the number on the  
remote control.  
Note for using the Number button on the remote  
control:  
Procedures must be followed within 5 seconds or  
the Picture Control mode will be cancelled.  
When setting the Picture Control, the Game mode  
will be cancelled.  
Make sure ...  
¡You must procede single-digit channel numbers  
with a zero (For example: 02, 03, 04 and so on).  
¡When selecting cable channels which are higher  
than 99, press +100 first, then press the last two  
digits. (Example: to select channel 125, first press  
“+100” then press “2” and “5”).  
TV/VCR/DVD power must be turned on.  
1 Select “PICTURE CONTROL”  
Press the PICTURE button on the remote control.  
Remember: If the TV/VCR/DVD is connected to a  
cable box or satellite box, the TV/VCR/DVD must  
be on CH3 or CH4, then the channel to be viewed  
must be selected on the cable box or satellite box.  
2 Select item you want to adjust  
Press the Arrow button K or L until desired control  
is displayed.  
BRIGHT  
CONTRAST  
COLOR  
TINT  
3 Adjust sound  
Press the VOLUME button X or  
Y
BRIGHT  
P
P
P
P
P
P
P
C
P
P
P
P
P
P
P +  
to adjust the volume.  
SHARPNESS  
VOLUME 20  
C
C
C
C
C
C
C
C
C
C
C
C
3 Adjust the picture control  
NOTES:  
Press the Arrow button s or B to adjust to your  
If you press the CHANNEL button K or L in the  
DVD mode, you can change the TV channels.  
Even if you turn off the TV/VCR/DVD in the  
DVD mode, when you turn it on again, it will go  
into the TV/VCR mode.  
desired level.  
Arrow Button  
{
Arrow Button  
B
to decrease  
brightness  
to increase  
brightness  
BRIGHT  
to increase  
contrast  
to decrease  
contrast  
CONTRAST  
DEGAUSSING  
to pale  
to purple  
to soft  
to brilliant  
to green  
COLOR  
TINT  
TV/VCR  
Magnetism from nearby appliances and speakers  
might affect the color of the TV picture.  
to clear  
SHAPNESS  
If there is a power failure of any kind, the  
TV/VCR/DVD will retain its memory for this fea-  
ture.  
If this happens, move this TV/VCR/DVD away from  
the appliance. If the color is still not correct, unplug  
the power cord, then plug it in again 30 minutes later  
or so.  
- 19 -  
EN  
1C29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CLOSED CAPTION SYSTEM  
- TV/VCR SETUP -  
1 Select “CAPTION”  
Press the SETUP button on the  
remote control.  
Press the Arrow button K or L to  
point to “CAPTION”.  
TIMER PROGRAMMING  
SETTING CLOCK  
CHANNEL SET UP  
USER’S SET UP  
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
TV/VCR  
B
You can view specially labeled (cc) TV programs,  
movies, news and pre-recorded tapes with either a  
dialogue caption or text display.  
TIME SEARCH  
INDEX SEARCH  
CAPTION mode: By choosing the caption mode, you  
can watch dramas, movies and news while captioning  
the dialogues and the contents of news.  
TEXT mode: By choosing the text mode, you can  
watch half screen text information if you want.  
1-2: You may get these captions or text information  
by selecting either “1” or “2”. Caption “2” is used,  
usually for a second language if available.  
2 Select your desired caption menu  
- TV/VCR SETUP -  
Press the ENTER button until your  
TIMER PROGRAMMING  
SETTING CLOCK  
CHANNEL SET UP  
USER’S SET UP  
desired caption menu appears.  
([CAPTION1], [CAPTION2],  
[TEXT1] or [TEXT2])  
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [CAPTION1]  
ZERO RETURN  
B
TIME SEARCH  
INDEX SEARCH  
3 Exit the caption setting mode  
NOTE:  
Press the SETUP button on the remote control to  
return to TV mode.  
Not all programs are broadcast with closed captions.  
Your TV/VCR/DVD is designed to provide error free  
closed captions from high quality antenna, cable and  
VCR signals. Conversely, poor quality signals are  
likely to result in caption errors or no captions at all.  
Common signal conditions which may cause captions  
errors are listed below:  
TO CANCEL THE CLOSED CAPTION  
SYSTEM  
Repeat steps [1] and [2], select [OFF] using the  
ENTER button. Press the SETUP button on the  
remote control to return to TV mode.  
Automobile ignition noise  
Electric motor brush noise  
Weak snowy reception on TV screen  
Multiplex signal reception displaying picture  
WHEN THE CLOSED CAPTION MODE  
IS ON  
The On-Screen Display will disappear after 5 sec-  
onds.  
It will also disappear when the MUTE button is  
pressed and when the PAUSE button is pressed  
while recording.  
ghosts or airplane flutter.  
Playback of poorly recorded or worn VCR tapes.  
NOTE:  
If the TV/VCR/DVD displays a  
black box on the TV screen, this  
means that the TV/VCR/DVD is  
set to the TEXT mode. To clear  
screen, select [CAPTION1], [CAP-  
TION2] or [OFF].  
If there is a power failure of any kind, the  
TV/VCR/DVD will retain its memory for this fea-  
ture.  
Make sure ...  
TV/VCR/DVD’s power must be turned on.  
- 20 -  
EN  
1C29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
V-CHIP SET UP SUB RATINGS  
When you select the ratings of TV-Y7,TV-PG,TV-14  
or TV-MA you will have the option of selecting sub  
rating categories.  
V-CHIP SET UP  
TV/VCR  
V-CHIP SET UP  
- TV/VCR SETUP -  
1 Select “V-CHIP SET UP”  
Make sure ...  
TIMER PROGRAMMING  
SETTING CLOCK  
Press the SETUP button on the  
remote control.  
CHANNEL SET UP  
USER’S SET UP  
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
TV/VCR/DVD is turned on.  
B
Press the Arrow button K or L to  
select “V-CHIP SET UP”. Then  
press the ENTER button.  
TIME SEARCH  
INDEX SEARCH  
1 Select “V-CHIP SET UP”  
Press the SETUP button on the  
remote control.  
Press the Arrow button K or L to  
select “V-CHIP SET UP”.  
Then press the ENTER button.  
- TV/VCR SETUP -  
TIMER PROGRAMMING  
SETTING CLOCK  
CHANNEL SET UP  
USER’S SET UP  
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
B
2 Enter Access code  
ACCESS CODE  
TIME SEARCH  
INDEX SEARCH  
Use the number buttons on the  
remote control to enter the access  
code. (Default code is 0000.)  
_
_
_
_
2 Enter Access code  
Use the number buttons on the remote  
control to enter the access code.  
ACCESS CODE  
– V-CHIP SET UP –  
3 Select “TV RATING”  
Press the Arrow button K or L to  
select “TV RATING”.  
_
_
_
_
B TV RATING  
MPAA RATING  
CHANGE CODE  
For the first time set-up or in the  
event the TV/VCR/DVD has lost  
power, enter the default code of  
the numbers: 0000.  
Then press the ENTER button.  
– V-CHIP SET UP –  
4 Selecting “Sub-Ratings”  
Press the Arrow button L or K to select the sub-rat-  
ing you wish to block. Then press the ENTER button  
twice.  
3 Select “TV RATING”  
Press the Arrow button K or L to  
select “TV RATING”.  
B TV RATING  
MPAA RATING  
CHANGE CODE  
Then press the ENTER button.  
When you select [TV-Y7]:  
TV–Y7  
FV  
[BLOCK]  
[BLOCK]  
Press the Arrow button L or K to  
select “FV” (Fantasy Violence).  
Then press the ENTER button to  
select [BLOCK] or [VIEW].  
When you select [TV-PG], [TV-  
14] or [TV-MA]:  
Press the Arrow button L or K to  
select “D”(Suggestive Dialog),  
“L”(Coarse Language),  
“S”(Sexual Situation), or “V”(Violence). Then  
press the ENTER button to select [BLOCK] or  
[VIEW].  
Note: When you select [TV-MA], “D” does not  
appear on the TV screen.  
The sub-ratings which set to  
4 Blocking TV programs  
Press the Arrow button K or L to  
select “TV rating” that you wish to  
block.  
Press the ENTER button to turn it  
[BLOCK].  
B
B
TV–Y  
TV–Y7  
TV–G  
TV–PG (  
TV–14  
TV–MA(  
[VIEW]  
(
)
[VIEW]  
[VIEW]  
[VIEW]  
[VIEW]  
[VIEW]  
)
)
)
(
TV–PG  
[BLOCK]  
B
D
L
S
V
[BLOCK]  
[BLOCK]  
[BLOCK]  
[BLOCK]  
When you select the rating category and turn it  
[BLOCK], the higher rating will turn [BLOCK]  
automatically. Also, the lower rating will turn  
[VIEW] automatically.  
When you turn “TV-Y” to [VIEW], all ratings will  
turn to [VIEW] automatically.  
Selection  
TV-Y  
Rating Category Explanations  
Appropriate for all children  
B
TV–Y  
TV–Y7  
TV–G  
TV–PG (DLSV)  
TV–14 (DLSV)  
TV–MA ( LSV)  
[VIEW]  
(
)
[VIEW]  
[VIEW]  
[BLOCK] appears next to the rat-  
ing category in the TV rating  
menu.  
[BLOCK]  
[BLOCK]  
[BLOCK]  
TV-Y7  
TV-G  
Appropriate for children seven and older  
General Audience  
TV-PG  
TV-14  
Parental Guidance suggested.  
Unsuitable for children under 14  
5 Exit the V-Chip setting mode  
Press the SETUP button on the remote control to  
enter the setting and exit the screen.  
TV-MA Mature audience only  
5 Exit the V-Chip setting mode  
Press the SETUP button on the remote control to  
exit the screen.  
- 21 -  
EN  
1C29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CHANGING V-CHIP BLOCKED PRO-  
GRAMMING  
Note: To change the rating, the TV must be turned to  
a station that is not protected. If the (PROTECTED)  
appears on the screen, please change the channel to a  
station that is not protected.  
5 Exit the V-Chip setting mode  
Press the SETUP button on the remote control to  
exit the screen.  
1)Follow steps [1] and [2].  
CHANGE ACCESS CODE  
2)Press the Arrow button K or L to select "TV RAT-  
ING". Then press the ENTER button. Select a TV  
rating to be unblocked by pressing the Arrow but-  
ton K or L.  
Then press the ENTER button to unblock the rating.  
3)Press the SETUP button on the remote control to  
exit the screen.  
To change access code, follow the steps.  
1 Select “V-CHIP SET UP”  
Press the SETUP button on the remote control.  
Press the Arrow button K or L to select “V-CHIP  
SET UP”.  
Then press the ENTER button.  
MPAA RATING SET UP  
2 Enter Access code  
ACCESS CODE  
- TV/VCR SETUP -  
Use the number buttons on the remote  
1 Select “V-CHIP SET UP”  
Press the SETUP button on the  
remote control.  
Press the Arrow button K or L to  
select “V-CHIP SET UP”. Then  
press the ENTER button.  
TIMER PROGRAMMING  
_
_
_
_
SETTING CLOCK  
CHANNEL SET UP  
control to enter the access code.  
The default code is 0000.  
USER’S SET UP  
B
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
TIME SEARCH  
INDEX SEARCH  
– V-CHIP SET UP –  
3 Select “CHANGE CODE”  
Press the Arrow button K or L to  
select "CHANGE CODE". Then  
press the ENTER button.  
TV RATING  
MPAA RATING  
B CHANGE CODE  
2 Enter Access code  
Use the number buttons on the  
remote control to enter the access  
code.  
ACCESS CODE  
_
_
_
_
4 Enter New code  
NEW CODE  
Use the number buttons to enter  
your desired access code in the  
NEW CODE space. Then enter the  
same code in the CONFIRM  
CODE space. V-CHIP SET UP  
screen appear on the screen.  
X X X X  
CONFIRM CODE  
– V-CHIP SET UP –  
3 Select “MPAA RATING”  
Press the Arrow button K or L to  
point to “MPAA RATING”.  
Then press the ENTER button.  
_
_
_
_
TV RATING  
B MPAA RATING  
CHANGE CODE  
If you enter wrong code, repeat step 4, making  
sure you enter the same new code exactly in the  
confirm code space.  
4 Select your desired item  
Press the Arrow button K or L to  
point to your desired item.  
G
[VIEW]  
PG  
[VIEW]  
PG–13  
R
NC–17  
X
[VIEW]  
B
[BLOCK]  
[BLOCK]  
[BLOCK]  
Then press the ENTER button to  
select [BLOCK] or [VIEW].  
5 Exit the V-Chip setting mode  
Press the SETUP button on the remote control to  
exit the screen.  
Selection  
G
Rating Category Explanations  
General Audience  
Note: If you unplug the power cord or power failure  
occurs, the changed access code will be lost and will  
return to default (0000). Change your access code  
again as necessary.  
PG  
PG-13  
R
Parental Guidance suggested.  
Unsuitable for children under 13  
Restricted; under 17 requires accompa-  
nying parent or adult guardian  
No one under 17 admitted  
NC-17  
X
Mature audience only  
When you select the rating category and turn it  
[BLOCK], the higher rating will turn [BLOCK]  
automatically. Also, the lower rating will turn  
[VIEW] automatically.  
When you turn “G” to [VIEW], all ratings will turn  
to [VIEW] automatically.  
- 22 -  
EN  
1C29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MTS(Multi-Channel Television sound)SYSTEM  
You can record or listen to a program in MTS stereo.  
CHECKING THE SELECTED MTS MODE  
TV/VCR  
When you play a VHS tape, or receive a broadcast  
on the TV/VCR/DVD tuner channel you are watching,  
the status shown below will appear when you press  
the DISPLAY button on the remote control.  
1) When a program is broadcast in stereo, STEREO  
appears on the TV screen.  
2) When a program is broadcast in second audio,  
SAP appears on the TV screen.  
3) When a program broadcast both in stereo and sec-  
ond audio, STEREO and SAP appear on the TV  
screen.  
NOTE: Although a program may be broadcast in  
both stereo and second audio, you cannot  
record in both stereo and second audio at  
the same time.  
B
PLAY  
HIFI  
12:00AM  
CH 123  
STEREO/SAP  
4)  
3)  
2)  
1)  
4) While the TV/VCR/DVD is set in HIFI stereo  
mode and playback mode. HIFI appears on the  
TV screen. While the TV/VCR/DVD is set in  
monaural(MONO) mode, HIFI disappears from  
the TV screen.  
SP  
COUNT  
0:00:00  
Second Audio Program, which means your  
program, can also be received in a second  
language or sometimes a radio station.  
SAP  
NOTE: If you play non-HIFI tapes while the  
TV/VCR/DVD is set in HIFI, HIFI will  
disappear from the TV screen and the  
TV/VCR/DVD will play automatically in  
monaural.  
High Fidelity which produces better sound  
than standard stereo TV/VCR/DVDs.  
HIFI  
MTS RECORDING/MONITOR MODE  
TV/VCR  
Type of broadcast Display on  
STEREO/SAP  
Hi-Fi audio track(2-channel) Normal audio  
the TV screen SELECTION  
L-channel  
R-channel  
track  
Regular  
-None-  
-Invalid-  
Mono  
Mono  
Mono  
(monaural audio)  
Stereo broadcast  
Bilingual broadcast  
STEREO  
SAP  
-Invalid-  
STEREO*  
L
R
L+R  
Main audio  
program  
Main audio  
program  
Main audio  
program  
SAP*  
Sub audio  
program  
Sub audio  
program  
Sub audio  
program  
Stereo & Bilingual  
broadcast  
STEREO  
SAP  
STEREO*  
SAP*  
L
R
L+R  
sub audio  
program  
sub audio  
program  
sub audio  
program  
*You must select the recording mode in TV AUDIO [STEREO] or [SAP] when you record a broadcast.  
- 23 -  
EN  
1C29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SELECTING THE MTS SYSTEM  
TV/VCR  
Make sure ...  
TV/VCR/DVD power must be turned on.  
TO SELECT MONO MODE  
You can change the selection to “MONO” if you  
want to listen to HIFI tapes in normal audio play-  
back.  
TO SELECT HIFI MODE  
1) Press the SETUP button on the remote control.  
1 Select “USER’S SET UP”  
Press the SETUP button on the  
remote control.  
Press the Arrow button K or L to  
point to “USER’S SET UP”. Then  
press the ENTER button.  
- TV/VCR SETUP -  
Press the Arrow button K or L to point to “USER’S  
SET UP”. Then press the ENTER button.  
2) Press the Arrow button K or L to point to  
“VCR AUDIO”.  
3) Press the ENTER button until [MONO] appears.  
4) Press the SETUP button on the remote control to  
return to TV mode.  
TIMER PROGRAMMING  
SETTING CLOCK  
CHANNEL SET UP  
USER’S SET UP  
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
B
TIME SEARCH  
INDEX SEARCH  
2 Select“VCR AUDIO”  
Press the Arrow button K or L to  
point to“VCR AUDIO”.  
– USER’S SET UP –  
RENTAL  
[OFF]  
REPEAT PLAY  
AUTO RETURN  
VCR AUDIO  
TV AUDIO  
[OFF]  
[OFF]  
[HIFI]  
[STEREO]  
TO SELECT STEREO, SAP, OR MONO  
B
1 Select “USER’S SET UP”  
- TV/VCR SETUP -  
Press the SETUP button on the  
TIMER PROGRAMMING  
SETTING CLOCK  
CHANNEL SET UP  
remote control.  
Press the Arrow button K or L to  
point to “USER’S SET UP”.  
B
USER’S SET UP  
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
TIME SEARCH  
3 Select [HIFI]  
Press the ENTER button until  
[HIFI] appears.  
– USER’S SET UP –  
INDEX SEARCH  
RENTAL  
[OFF]  
REPEAT PLAY  
AUTO RETURN  
VCR AUDIO  
TV AUDIO  
[OFF]  
[OFF]  
[HIFI]  
[STEREO]  
B
– USER’S SET UP –  
2 Select “TV AUDIO”  
Press the Arrow button K or L to  
point to“TV AUDIO”.  
RENTAL  
[OFF]  
REPEAT PLAY  
AUTO RETURN  
VCR AUDIO  
TV AUDIO  
[OFF]  
[OFF]  
[HIFI]  
[STEREO]  
4 To return to TV mode  
Press the SETUP button on the remote control to  
return to TV mode.  
B
3 Select [STEREO], [SAP], or [MONO]  
Press the ENTER button until [STEREO], [SAP], or  
[MONO] appears.  
NOTES:  
Normally “HIFI” should be selected for playback  
with HIFI sound.  
When you play non-HIFI tapes, the TV/VCR/DVD  
will play automatically in the monaural mode.  
The TV/VCR/DVD records automatically MTS  
broadcasts in HIFI stereo sound unless you select  
SAP mode recording before you begin recording.  
4 To return to TV mode  
Press the SETUP button on the remote control to  
return to TV mode.  
NOTES:  
You must select the recording mode,either TV  
AUDIO [STEREO] or [SAP] when you record a  
broadcast.  
“MTS RECORDING/MONITOR  
Refer to  
MODE”.  
If you select second audio when second audio is  
not available, the TV/VCR/DVD will record nor-  
mal audio.  
The TV/VCR/DVD records automatically MTS  
broadcasts in HIFI stereo sound unless you select  
SAP mode recording before you begin recording.  
- 24 -  
EN  
1C29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
VIDEO CASSETTE  
This TV/VCR/DVD will operate with any cassette that has the  
mark. For best results,  
we recommend the use of high-quality tapes. Do not use poor quality or damaged tapes.  
PRECAUTIONS  
INSERTING A CASSETTE  
Avoid moisture. Moisture condensation may occur  
Insert the cassette in the direction as shown. Push in  
gently, but continuously, on the center-back of the  
cassette until it is drawn into the TV/VCR/DVD. The  
TV/VCR/DVD will automatically turn on.  
on the tape if it is moved from a cold place to a  
warm place or visa versa. Before using a tape with  
these conditions, to avoid damage of the tape and  
your TV/VCR/DVD, wait until the tape has  
warmed to room temperature and the moisture has  
evaporated.  
Window  
Avoid extreme heat, high humidity and magnetic  
fields.  
Do not tamper with the cassette mechanism.  
Do not touch the tape with your fingers.  
WRONG  
CORRECT  
TWO DIFFERENT TAPE SPEEDS  
REMOVING A CASSETTE  
Before recording, select the tape speed from : SP  
mode (Standard Play) or SLP mode (Super Long  
Play).  
The table below shows the maximum recording/play-  
back time using T60, T120 or T160 tapes in each  
mode.  
1)In the Stop mode, press the STOP/EJECT button  
on the TV/VCR/DVD. The cassette will eject.  
2)Pull the cassette out of the cassette compartment.  
3)Store the cassette in its case as shown.  
Tape Speed  
Type of tape  
SP mode  
Recording/Playback Time  
T60  
1 hour  
3 hours  
T120  
T160  
2 hours 2-2/3 hours  
6 hours 8 hours  
SLP mode  
ERASE PREVENTION  
Note: You can play back a tape recorded in LP mode  
(Long Play).  
You can prevent accidental  
erasing of recording by  
breaking off the tab on the  
back edge of the cassette.  
Tab  
If you decide to record on  
the tape again, cover the  
hole with plastic tape.  
Plastic Tape  
NOTE:  
• In DVD mode, Whether the cassette is with tab or  
without tab you insert, it doesn’t start playing until  
you press the PLAY button.  
In TV/VCR mode, if the cassette without tab is  
inserted, playback will automatically start.  
- 25 -  
EN  
1C29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PLAYBACK  
NORMAL PLAYBACK  
SLOW MOTION  
TV/VCR  
TV/VCR  
Press the PAUSE button, then press the F.FWD  
g
Make sure ...  
button to start the playback in slow motion. The  
TV/VCR/DVD power must be turned on.  
TV/VCR/DVD mutes the sound during slow motion.  
Press the PLAY button to return to normal playback.  
NOTE: If it is left in the Slow mode for more than  
five minutes, the TV/VCR/DVD will automatically  
go into the Stop mode.  
1 Insert a prerecorded tape  
If the erase-protection tab has been removed, the  
TV/VCR/DVD will start playback automatically.  
STILL PICTURE  
B
PLAY  
2 To begin playback  
Press the PLAY button.  
TV/VCR  
You can view a still picture on the TV screen during  
playback (the Still mode). Press the PAUSE button  
during playback. Only tapes recorded in the SLP  
mode will show the least amount of lines. Press the  
PLAY button to return to playback.  
3 To stop playback  
STOP  
NOTES:  
Press the STOP button when play-  
back is completed.  
You can advance the picture one frame at a time by  
pressing the PAUSE button during the Still mode.  
If it is left in the Pause mode for more than five  
minutes, the TV/VCR/DVD will automatically  
switch to the Stop mode.  
NOTES:  
If you press the PLAY button (of the TV/VCR side)  
in the DVD mode, you can start the VCR playback.  
If you press the SELECT button during the VCR  
playback, it will stop and the mode will change to  
the DVD mode. In addition, the same function  
operates with the DVD side PLAY button or the  
OPEN/CLOSE button.  
VERTICAL HOLD CONTROL  
TV/VCR  
In the Pause/Still mode only, when the picture begins  
to vibrate vertically, stabilize the picture by pressing  
the CHANNEL button K or L.  
NOTE:  
If there are video noise lines on the screen, see Tracking  
Adjustment section.  
TRACKING ADJUSTMENT  
TV/VCR  
Tracking adjustment will be set automatically  
(Digital Tracking function) when you start play-  
back.  
However when playing pre-recorded tapes or tapes  
recorded on other VCR, noise lines (black and  
white streaks) may appear on the playback picture.  
If this occurs, you can adjust the tracking control  
manually by pressing the CHANNEL button K or  
L until the streaks disappear. To return to the DTR  
function, stop the tape once and start playback  
again.  
You can reduce the noise lines by pressing the  
CHANNEL button K or L in slow mode too.  
Tracking adjustment in Slow mode will not be set  
automatically.  
- 26 -  
EN  
1C29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SPECIAL PLAYBACK  
Make sure ...  
AUTO REPEAT PLAYBACK  
TV/VCR/DVD’s power must be turned on.  
Insert a prerecorded tape.  
TV/VCR  
The TV/VCR/DVD has the auto repeat function that  
allows you to repeat a tape indefinitely without  
touching the PLAY button.  
ALL REPEAT: Repeat playback from the beginning  
to the end of the tape.  
BLANK REPEAT: Repeat playback from the begin-  
ning to a blank part, which is blank for more than  
10 seconds.  
RENTAL PLAYBACK  
TV/VCR  
This function enables you to improve the picture  
quality when playing back worn cassettes such as  
rented tapes.  
1 Select “USER’S SET UP”  
- TV/VCR SETUP -  
TIMER PROGRAMMING  
SETTING CLOCK  
Press the SETUP button on the  
CHANNEL SET UP  
- TV/VCR SETUP -  
1 Select “USER’S SET UP”  
B
USER’S SET UP  
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
TIME SEARCH  
TIMER PROGRAMMING  
SETTING CLOCK  
CHANNEL SET UP  
remote control.  
Press the SETUP button on the  
B
USER’S SET UP  
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
TIME SEARCH  
Press the Arrow button K or L to  
point to “USER’S SET UP”.  
Then press the ENTER button.  
remote control.  
INDEX SEARCH  
Press the Arrow button K or L to  
point to “USER’S SET UP”.  
Then press the ENTER button.  
INDEX SEARCH  
2 Set “RENTALto [ON]  
Press the Arrow button K or L to  
point to “RENTAL”.  
Press the ENTER button until [ON]  
appears.  
USER’S SET UP  
B
RENTAL  
[ON]  
2 Select “ALLor “BLANK”  
Press the Arrow button K or L to  
point to “REPEAT PLAY”.  
USER’S SET UP  
REPEAT PLAY  
AUTO RETURN  
VCR AUDIO  
TV AUDIO  
[OFF]  
[OFF]  
[HIFI]  
[STEREO]  
RENTAL  
[OFF]  
B
REPEAT PLAY  
AUTO RETURN  
VCR AUDIO  
TV AUDIO  
[ALL]  
[OFF]  
[HIFI]  
[STEREO]  
Press the ENTER button repeatedly  
until your desired selection [ALL]  
or [BLANK] appears.  
3 Exit the Rental setting  
Press the SETUP button on the remote control to  
return to the TV mode.  
3 Exit the Repeat Play setting  
Press the SETUP button on the remote control to  
return to the TV mode.  
4 Start playback  
Press the PLAY button to start playback. “RENTAL  
PLAY B” appears.  
Once you select the Rental mode, it stays in effect  
even after you turn off the TV/VCR/DVD.  
4 Start playback  
Press the PLAY button to start the Repeat Play.  
“REPEAT PLAY B” appears.  
Once you select the Repeat Play mode, it stays in  
effect even after you turn off the TV/VCR/DVD.  
TO CANCEL THE RENTAL MODE  
If the Rental mode is set [ON], the “RENTAL  
PLAY B” display has priority.  
Repeat steps [1] and [2], select [OFF] using the  
ENTER button on the remote control. Press the  
SETUP button on the remote control to return to TV  
mode.  
If there is a power failure of any kind, the TV/  
VCR/DVD will retain its memory for this feature.  
TO CANCEL THE REPEAT PLAY MODE  
Repeat steps [1] and [2], select [OFF] using the  
ENTER button on the remote control. Press the  
SETUP button on the remote control to return to TV  
mode.  
If there is a power failure of any kind, the  
TV/VCR/DVD will retain its memory for this fea-  
ture.  
- 27 -  
EN  
1C29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SEARCH  
Make sure ...  
TIME SEARCH  
TV/VCR/DVD power must be turned on.  
Insert a tape.  
TV/VCR  
The Time Search function makes it possible to quick-  
ly advance the tape to your desired position simply  
by entering the exact amount of playback time you  
want to skip.  
ZERO RETURN  
TV/VCR  
This function allows you to search easily a beginning point  
that you want to review by rewinding or fast forwarding.  
NOTES:  
Time Search can be set up to a maximum of 9  
hours 50 minutes (9:50) by 10 minutes at a time.  
NOTE:  
Zero Return WILL NOT work on a blank tape or a  
blank portion of a tape.  
This function will not operate in recording mode.  
This function is not operative when a cassette tape  
is not inserted in the TV/VCR/DVD.  
In the example below: To watch a program before/  
after 2 hour 50 minutes from the present position, in  
either direction.  
1 Stop a tape at your desired point  
Rewind or fast forward the tape to the beginning  
point at which you want to review.  
2 Reset the counter to 0:00:00  
Press the C.RESET button repeatedly.  
1 Insert a tape  
3 Begin recording or playback  
Press the RECORD or PLAY button.  
2 Select “TIME SEARCH” mode  
Press the STOP button when recording or playback is completed.  
Press the SETUP button on the  
remote control.  
- TV/VCR SETUP -  
TIMER PROGRAMMING  
SETTING CLOCK  
CHANNEL SET UP  
USER’S SET UP  
V-CHIP SET UP  
4 To activate “ZERO RETURN” mode  
Press the Arrow button K or L to  
point to “TIME SEARCH”.  
Then press the ENTER button.  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
- TV/VCR SETUP -  
Press the SETUP button on the  
TIMER PROGRAMMING  
SETTING CLOCK  
B
TIME SEARCH  
remote control.  
CHANNEL SET UP  
INDEX SEARCH  
USER’S SET UP  
V-CHIP SET UP  
Press the Arrow button K or L to  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
point to “ZERO RETURN”.  
Then press the ENTER button.  
B
ZERO RETURN  
TIME SEARCH  
INDEX SEARCH  
3 Enter your desired time  
Press the Arrow button K or L until  
your desired time appears.  
(Example: “2:50” stands for 2 hours  
50 minutes)  
The counter will appear on the TV screen.  
The tape will automatically stop when the counter  
returns to 0:00:00.  
TIME SEARCH  
2 : 50  
PICTURE SEARCH  
If you wish to cancel the Time  
Search at this point, press the SETUP button on the  
remote control.  
TV/VCR  
This feature is very useful in finding or skipping over a par-  
ticular scene on a tape. In this mode, the sound will be muted.  
1)You may view a video tape at a high speed in  
either a forward or reverse direction by pressing  
the F.FWD g or REW h button during play-  
back. (in the SP / LP / SLP modes)  
4 Begin Time Search  
By pressing the Arrow button s or B, the  
TV/VCR/DVD will rewind or fast forward to the  
specified point.  
The time counts down as the searching progresses.  
When 0:00 is reached, the tape will start playback  
automatically.  
NOTE:  
g
h
If you press the F.FWD  
or REW  
button  
on the front panel in the DVD mode, the VCR for-  
ward or reverse will start. Please press the STOP /  
EJECT button once to stop it, twice to eject it.  
TO CANCEL THE TIME SEARCH at this  
point  
2)Press it again and the TV/VCR/DVD will now search  
in super high speed. (in the LP / SLP modes only)  
NOTE:  
Press the STOP/EJECT button on the TV/VCR/DVD  
or the STOP button on the remote control. This will  
delete the selected time.  
Tapes recorded in the SP or LP mode will dis-  
play a noise bar on the TV screen and the picture  
may revert to Black and White. This is normal.  
3)Press the PLAY button to return to normal speed.  
- 28 -  
EN  
1C29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INDEX SEARCH  
1 Select “INDEX SEARCH”  
Press the SETUP button on the  
remote control.  
Press the Arrow button K or L to  
point to “INDEX SEARCH”. Then  
press the ENTER button.  
- TV/VCR SETUP -  
TIMER PROGRAMMING  
SETTING CLOCK  
CHANNEL SET UP  
USER’S SET UP  
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
TV/VCR  
This feature provides a method of indexing the start-  
ing point so that it can be easily returned to in either  
fast forward or rewind mode.  
TIME SEARCH  
INDEX SEARCH  
B
The index mark will be made automatically when  
the RECORD button is pressed. It will also be  
marked at the starting point of Timer recording and  
OTR.  
2 Enter your desired number  
Press the Arrow button K or L until  
the number of programs that you  
want to skip appears.  
INDEX SEARCH  
0 3  
The index mark will not be recorded if the PAUSE  
button is pressed and released during recording.  
The time gap between making the index marks on  
the tape should be greater than 1 minute for SP  
recording, 2 minutes for LP recording and 3 min-  
utes for SLP recording.  
(Example: “03” for 3 programs)  
The Index Search mode will be  
canceled if the procedures are not activated in 30  
seconds.  
In some cases, the index mark at the beginning of  
video tape cannot be detected.  
3 Begin Index Search  
Press the Arrow button s or B. The TV/VCR/DVD  
begins rewinding or fast forwarding to the beginning  
of desired program.  
NOTE: Every time an index signal is skipped, the  
number in the program indicator decreases by one.  
Example: You are watching program number 4 and  
want to fast forward to program number 7. You  
must skip three programs.  
CURRENT PLAYBACK PROGRAM  
Beginning of tape  
Pro.1 Pro.2 Pro.3 Pro.4 Pro.5 Pro.6 Pro.7  
End of tape  
4 After Index Search  
When the preset program is reached, the  
TV/VCR/DVD will start playback automatically.  
4
3
2
1
1
2
3
A video cassette must be inserted in the  
TV/VCR/DVD for this function to work.  
INDEX MARK  
The number of Index Searches can be set up to 20.  
This function will not operate in the recording mode.  
When you want to cancel the Index Search while  
in progress, press the STOP button.  
SPECIAL FEATURES  
REAL TIME TAPE COUNTER  
AUTO REWIND-EJECT  
TV/VCR  
TV/VCR  
When the end of a tape is reached during record-  
ing, playback, or fast-forward, the tape will auto-  
matically rewind to the beginning. After rewinding  
finishes, the TV/VCR/DVD will eject the tape and  
turn itself to off.  
This shows the elapsed recording or playback time in  
hours, minutes, and seconds. (The displayed time will  
not change on a blank tape or blank portions on the  
tape.)The “–” indication will appear when the tape has  
rewound further than “0:00:00” on the tape counter.  
This function is operative when Repeat Play is set  
to the [OFF] position.  
The tape will not auto-rewind during timer record-  
ing or One Touch Recording.  
- 29 -  
EN  
1C29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
RECORDING  
Make sure ...  
TV/VCR/DVD power must be turned on.  
Insert a cassette tape with its erase prevention tab in place. (If necessary, rewind or fast forward the tape to  
the point at which you want to begin recording.)  
NOTES:  
This TV/VCR/DVD will ONLY record and view the same channel.  
This TV/VCR/DVD cannot record the contents from the built-in DVD.  
SKIPPING UNWANTED  
NORMAL RECORDING  
SCENES DURING RECORDING  
TV/VCR  
TV/VCR  
You can ONLY watch the same TV program that is  
being recorded.  
Press the PAUSE button to tem-  
PAUSE  
porarily stop recording.  
Press the PAUSE or RECORD but-  
ton to resume recording.  
NOTES:  
1 Select the channel to be recorded  
Press the number buttons on the  
SP  
CH 10  
remote control or the CHANNEL  
button K or L.  
Remember: If the TV/VCR/DVD  
is connected to a cable box or satel-  
lite box, the TV/VCR/DVD must be  
on CH3 or CH4, then the channel to be recorded  
must be selected on the cable box or satellite box.  
After five minutes, the  
TV/VCR/DVD will automatically switch to the  
Recording mode to prevent tape damage.  
If “CLOSED CAPTION (ON)” is selected, the On-  
Screen Display will appear for 5 seconds, then dis-  
appear.  
2 Select the tape speed  
Press the SPEED button to select  
the desired tape speed (SP/ SLP).  
SP  
REC  
3 Begin recording  
Press the RECORD button.  
SP  
4 Stop recording  
Press the STOP button when recording is completed.  
- 30 -  
EN  
1C29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Push(es) Display  
1 push  
Recording length  
(normal recording)  
OTR (One Touch Recording)  
2 pushes  
3 pushes  
0:30  
1:00  
30 minutes  
60 minutes  
TV/VCR  
This function enables you to set a recording length  
simply by pressing the REC/OTR button on the  
TV/VCR/DVD.  
17 pushes  
8:00  
480 minutes  
Make sure ...  
TV/VCR/DVD power must be turned on.  
Insert a cassette tape with its erase prevention tab in  
place. (If necessary, rewind or fast forward the tape  
to the point at which you want to begin recording.)  
NOTES:  
You cannot start OTR with the remote control.  
Recording starts immediately when the REC/OTR  
button is pressed.  
COPYING A VIDEO CASSETTE  
(Requires a VCR or camcorder)  
TV/VCR  
You can make copies of video tapes made by friends  
or relatives for your enjoyment.  
You can not copy a DVD to a videotape.  
When the REC/OTR button is pressed 18 times, the  
TV/VCR/DVD returns to the Normal Recording mode.  
To stop the OTR operation, press the STOP button  
on the TV/VCR/DVD or on the remote control.  
WARNING: Unauthorized recordings of  
copyrighted video tapes may be an  
infringement of copyright laws.  
Connect your TV/VCR/DVD and a Source (Playing)  
VCR using the following diagram.  
To show the remaining time, press the DISPLAY  
button on the remote control so that “OTR”  
appears on the TV screen. (It will show up  
momentarily then disappear.)  
[Fig.8]  
[The TV/VCR/DVD]  
Recording stops when 0:00 is reached.  
Please note that in the SLP mode maximum record-  
ing time, assuming the tape is started at the begin-  
ning, is 8 hours using T-160 (or 6 hours using T-120).  
STOP/EJECT  
F.FWD  
PLAY  
REW  
REC/OTR  
L
AUDIO  
R
HEADPHONE  
VIDEO  
If the tape runs out before the end time, the  
TV/VCR/DVD will switch to the Stop mode  
immediately, ejects the tape and turns itself off.  
[Ex: Source (playing)  
VCR or camcorder]  
If you press the POWER button during OTR, the  
TV/VCR/DVD continues recording until the  
selected length is reached.  
Audio/Video  
adapter cable  
(not supplied)  
AUDIO  
L
OUT  
IN  
R
VIDEO  
OUT  
IN  
1 Select the channel to be recorded  
Press the number buttons on the remote control or  
the CHANNEL button K or L.  
1)Insert a pre-recorded video cassette into the Source  
(Playing) VCR or camcorder.  
Remember: If the TV/VCR/DVD is connected to a  
cable box or satellite box, the TV/VCR/DVD must  
be on CH3 or CH4, then the channel to be recorded  
is selected on the cable box or satellite box.  
2)Insert a blank video cassette, or one you want to  
record over, into the TV/VCR/DVD’s cassette  
compartment.  
3)Press the SPEED button on remote control for the  
TV/VCR/DVD to select the desired recording  
speed (SP/SLP).  
4)Press the CHANNEL button K or L on the  
TV/VCR/DVD until “AUX” appears on the screen.  
5)Press the RECORD button on the TV/VCR/DVD.  
6)Begin playback of the tape in the source (Playing)  
VCR or camcorder.  
NOTE: For best results during copying, use the  
TV/VCR/DVD’s front panel controls whenever pos-  
sible. The remote control might affect the source  
(Playing) VCR’s playback operation.  
2 Select the tape speed  
Press the SPEED button to select the desired tape  
speed (SP/ SLP).  
3 Begin OTR  
Press the REC/OTR button on the TV/VCR/DVD as  
many times as needed. The recording  
length will be determined by the  
number of times you press the  
OTR(2 : 30)  
REC/OTR button. Each additional  
push will increase the recording time  
by 30 minutes. It is set up to 8 hours.  
7)To stop copying, press the STOP/EJECT button on  
the TV/VCR/DVD, then stop the tape on the  
source VCR or camcorder.  
SP  
- 31 -  
EN  
1C29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TIMER  
AUTOMATIC TIMER  
RECORDING  
1 Select “TIMER PROGRAMMING”  
- TV/VCR SETUP -  
Press the SETUP button on the  
remote control.  
B
TIMER PROGRAMMING  
SETTING CLOCK  
CHANNEL SET UP  
USER’S SET UP  
V-CHIP SET UP  
TV/VCR  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
Confirm “TIMER PROGRAM-  
MING” is pointed by pressing the  
Arrow button K, and press the  
ENTER button.  
You may set the TV/VCR/DVD to start and end a  
recording while you are away. You can set 8 pro-  
grams to record on specific days, daily or weekly  
within a 1 year period.  
TIME SEARCH  
INDEX SEARCH  
If you have not yet set the clock, “MANUAL  
CLOCK SET” appears. If so, follow steps [3] to  
[8] on pages 15~16. Then set the timer recording.  
In the example below, the timer is being set to record:  
DATE:  
July 4th, 2004  
SETTING TIME: from 7:30PM to 8:50PM  
CHANNEL:  
TAPE SPEED:  
CH61  
SP  
2 Select your desired program  
position (1~8)  
Press the Arrow button K or L to  
select the desired program position.  
Then press the Arrow button B.  
– TIMER PROGRAMMING –  
CH DATE  
BEGIN END  
Make sure ...  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
If a cable box or satellite box is connected with the  
TV/VCR/DVD you will be limited to record only one  
channel, and the channel selector on the  
B
TV/VCR/DVD must be selected to the output channel  
of the boxes CH 3 or CH 4 and then the actual chan-  
nel to be recorded must be selected on the boxes.  
Clock must be set to the correct time and date  
before setting the timer.  
TV/VCR/DVD power must be turn on to program it.  
Insert a cassette tape with its erase prevention tab  
in place. (If necessary, rewind or fast forward the  
tape to the point at which you want to begin  
recording.)  
3 Set the channel number  
Press the Arrow button K or L until  
the desired channel number  
appears. (Example: CH61)  
Then press the Arrow button B.  
Remember: If the TV/VCR/DVD  
is connected to a cable box or satellite box, the  
TV/VCR/DVD must be on CH3 or CH4, then the  
channel to be recorded is selected on the cable box or  
satellite box.  
– TIMER PROGRAMMING –  
CH DATE BEGIN END  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
61 -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
B
The channel you want to record is properly set in  
advance. (See page 18.)  
Avoid over lap of programs ...  
There is a chance that a program will not be record-  
ed, when programs overlap;  
4 Select once, every day or weekly recording  
For once recording :  
– TIMER PROGRAMMING –  
The program with an earlier start has priority.  
Once the earliest program finishes, the overlapping  
programs will begin recording in sequence.  
CH DATE  
BEGIN END  
Press the Arrow button K (up)  
until the desired date appears.  
(Example: “7/04” for July 4th).  
Then press the Arrow button B.  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
61 7/04 SUN -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
B
The illustration below demonstrates the sequence  
of recordings.  
Program 1  
Program 2  
Program 3  
10:00AM - 11:00AM  
9:00AM - 10:00AM  
9:30AM - 12:00PM  
For every day recording : To record a TV program  
at the same time on the same channel every day.  
(Example: Monday through Sunday)  
– TIMER PROGRAMMING –  
CH DATE  
BEGIN END  
Recording Sequence  
Press the Arrow button L (down)  
until “EVRY DAY” appears.  
Then press the Arrow button B.  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
61 EVRY DAY -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
Program 1  
10:00AM-11:00AM  
Program 2  
9:00AM-10:00AM  
Program 3  
B
9:30AM-12:00PM  
9:00AM  
10:00AM  
11:00AM  
12:00PM  
For weekly recording : To record a TV program at  
the same time on the same channel every week.  
*Recording period is SHADED  
(Example: every Monday)  
– TIMER PROGRAMMING –  
CH DATE  
BEGIN END  
Press the Arrow button L (down)  
until “EVRY” and your desired  
day of the week appear together.  
Then press the Arrow button B.  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
61 EVRY MON -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
B
- 32 -  
EN  
1C29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TIMER PROGRAM EXTENSION  
5 Set beginning hour  
– TIMER PROGRAMMING –  
CH DATE BEGIN END  
Press the Arrow button K or L until  
the desired hour appears.  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
TV/VCR  
61 7/04 SUN 7:12P  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
M
B
(Example: “ 7, PM” for 7:30PM)  
Then press the Arrow button B.  
To shift the time schedule of an automatic timer  
recording.  
1)Press the POWER button.  
– TIMER PROGRAMMING –  
CH DATE BEGIN END  
2)Repeat step [1] on page 32.  
6 Set beginning minute  
3)Press the RECORD button and select the desired  
program using the Arrow button K or L.  
4)Press the RECORD button again.  
Press the Arrow button K or L until  
the desired minute appears.  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
61 7/04 SUN 7:30P  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
M
B
(Example: “30” for 7:30PM)  
Then press the Arrow button B.  
Each additional push will shift forward the  
begin/end time for recording by 10 minutes. When  
the recording is already in progress, each additional  
push will shift forward the end time only. If you  
want to cancel while setting, press the PAUSE but-  
ton on the remote control. The recording time  
returns to the original time.  
NOTE: When you shift forward the time schedule  
during recording, the recording speed will automati-  
cally be set to the SLP mode.  
7 Set end hour  
Press the Arrow button K or L until  
the desired hour appears.  
(Example: “8, PM” for 8:50PM)  
Then press the Arrow button B.  
– TIMER PROGRAMMING –  
CH DATE BEGIN END  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
-:- - - -  
-:- - - -  
-:- - - -  
8:30PM- -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
61 7/04 SUN 7:30P  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
M
B
– TIMER PROGRAMMING –  
CH DATE BEGIN END  
8 Set end minute  
Press the Arrow button K or  
L
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
-:- - - -  
-:- - - -  
-:- - - -  
8:50PM- -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
5)Press the ENTER or RETURN button to exit the  
setting menu. Then press the SETUP button on the  
remote control to return to original mode.  
61 7/04 SUN 7:30P  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
M
until the desired minute appears.  
(Example: “50” for 8:50PM)  
Then press the Arrow button B.  
B
TO CORRECT A PROGRAM  
9 Set the tape speed  
Press the Arrow button K or  
until the desired tape speed  
appears. (Example: SP)  
While setting a program; press the Arrow button  
s to go back one step and enter the correct num-  
bers using the Arrow button K or L.  
After setting a program;  
– TIMER PROGRAMMING –  
CH DATE BEGIN END  
L
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
-:- - - -  
-:- - - -  
-:- - - -  
8:50PMSP  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
61 7/04 SUN 7:30P  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
M
B
1)Press the POWER button.  
2)Repeat steps [1] - [2] on page 32.  
3)Press the Arrow button B (or press the Arrow  
button s to go back one step) until the part you  
want to correct begins flashing, then make the  
changes pressing the Arrow button K or L.  
4)Press the POWER button to set automatic timer  
recording.  
10 Finish setting the program  
Press the ENTER or RETURN button. The program  
is now completed.  
To set another program, repeat steps [2] to [10].  
Press the SETUP button on the remote control to  
return to original mode.  
TO CANCEL AN AUTOMATIC TIMER  
RECORDING  
11 Set the timer  
Press the POWER button to set automatic timer  
recording. The RECORDING indicator lights up.  
After setting a program;  
1)Press the POWER button.  
You must turn off the TV/VCR/DVD to activate  
automatic timer recording.  
2)Repeat steps [1] ~ [2] on page 32 and select a  
program you want to cancel.  
3)Press the C.RESET button.  
4)Press the SETUP button on the remote control to  
return to TV mode.  
If power is not turned off and you continue watch-  
ing TV, TIMER REC STANDBY” starts flashing  
on the TV screen 2 minutes before the programmed  
start time.  
While recording is in progress;  
1)Press the POWER button.  
2)Press the STOP/EJECT button on the  
TV/VCR/DVD.  
- 33 -  
EN  
1C29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TO CHECK THE BEGIN/END TIME  
1)Press the POWER button so that the Recording  
indicator goes off.  
2)Press the SETUP button on the remote control.  
3)Confirm “TIMER PROGRAMMING” is pointed.  
4)Press the ENTER button. The details of programs  
appear on the TV screen.  
3 Auto Return will begin  
When all the timer recordings are completed, the  
TV/VCR/DVD will rewind to the beginning of the  
recorded program(s).  
NOTE:  
If you press the POWER button while tape is  
rewinding, the Auto Return will stop.  
5)Press the SETUP button on the remote control to  
return to TV mode.  
4 Watch the recorded program  
Press the PLAY button.  
HINTS FOR AUTOMATIC  
TIMER RECORDING  
TO CANCEL THE AUTO RETURN  
MODE  
TV/VCR  
Repeat steps [1] and [2], select [OFF] using the  
ENTER button.  
Make sure the channel you want to record is prop-  
erly set in advance.  
If there is a power failure of any kind, the  
TV/VCR/DVD will retain its memory for this fea-  
ture.  
It is not necessary to press the RECORD button for  
timer recording.  
Recording begins automatically at the Start time.  
The display will not be turned on when the programmed  
recording begins. To watch the currently recorded TV  
program or to play a DVD disc, press the POWER but-  
ton to turn on the display and use the SELECT button to  
choose the TV/VCR mode or the DVD mode.  
The erase-prevention tab on the cassette must be in  
place (or you must put tape over the hole).  
If the erase-prevention tab is removed, the cassette will  
be ejected when the POWER button is pressed to off.  
If the tape runs out before the end time, the  
TV/VCR/DVD will switch to the Stop mode  
immediately and the tape will be ejected.  
SLEEP TIMER  
TV/VCR  
The Sleep Timer function turns off the  
TV/VCR/DVD without using the POWER button  
after a desired period of time.  
NOTE:  
This function does not operate during Recording  
mode.  
1 Select “SLEEP TIMER”  
Press the SLEEP button on the remote control until  
“SLEEP TIMER” appears.  
AUTO RETURN  
TV/VCR  
2 Set sleep time  
With this feature, after timer recording is finished,  
the beginning of the recorded program(s) can be  
searched for automatically.  
Press the SLEEP button until your  
desired sleep time appears.  
Each additional push will increase  
the time by 30 minutes up to 120  
minutes.  
After 5 seconds, exit the Sleep Timer setting.  
SLEEP 120 MINUTES  
1 Select “USER’S SET UP”  
- TV/VCR SETUP -  
TIMER PROGRAMMING  
SETTING CLOCK  
Press the SETUP button on the  
CHANNEL SET UP  
B
USER’S SET UP  
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
TIME SEARCH  
remote control.  
Press the Arrow button K or L to  
point to “USER’S SET UP”.  
Then press the ENTER button.  
TO CANCEL THE SLEEP TIMER  
INDEX SEARCH  
Press the SLEEP button on the remote control until  
“SLEEP TIMER” appears. Press the SLEEP button  
until “SLEEP 0 MINUTES” appears.  
2 Set “AUTO RETURN” to [ON]  
Press the Arrow button K or L to  
point to “AUTO RETURN”.  
Press the ENTER button until [ON]  
appears.  
USER’S SET UP  
RENTAL  
[OFF]  
REPEAT PLAY  
AUTO RETURN  
VCR AUDIO  
TV AUDIO  
[OFF]  
B
[ON]  
[HIFI]  
[STEREO]  
- 34 -  
EN  
1C29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ON SCREEN DISPLAY  
To check the Counter, Clock and Channel number on the TV screen, press the DISPLAY button on the remote  
control. Each time you press the DISPLAY button on the remote control, the TV screen will change as follows:  
When the Closed Caption mode is OFF:  
When the Closed Caption mode is ON:  
Counter mode: After 5 seconds, only the counter  
remains. To clear it, press the DISPLAY button.  
Clock mode: After 5 seconds, only the clock and  
the channel number remain. To clear them, press  
the DISPLAY button.  
The On Screen Display disappear after 5 seconds.  
This is true even if the MUTE button is pressed or  
the PAUSE button is pressed while recording.  
OFF mode  
Clock/Counter mode  
OFF mode Counter mode  
Clock mode  
STOP  
STOP  
5:40PM  
CH2  
STOP  
5:40 PM  
CH2  
SP  
COUNT 0:12:34  
SP  
SP  
COUNT 0:12:34  
After 5 seconds  
After 5 seconds  
5:40PM  
CH2  
COUNT 0:12:34  
Counter  
remains  
Clock & Channel  
remains  
CABLE CHANNEL DESIGNATIONS  
If you subscribe to cable TV, the channels are displayed as 1-125. Cable companies often designate channels  
with letters or letter-number combinations. Please check with your local cable company. The following is a  
chart of common cable channel designations.  
CATV channel  
TV Display  
5A  
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
9
9
10  
10  
11  
11  
12  
12  
13  
13  
A
B
14  
15  
CATV channel  
TV Display  
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
28  
29  
30  
CATV channel  
R
S
T
U
V
W
W+1  
37  
W+2  
38  
W+3  
39  
W+4  
40  
W+5  
41  
W+6  
42  
W+7  
43  
W+8  
44  
W+9  
45  
TV Display  
31  
32  
33  
34  
35  
36  
CATV channel  
W+10 W+11 W+12 W+13 W+14 W+15 W+16 W+17 W+18 W+19 W+20 W+21 W+22 W+23 W+24  
46 47 48 49 50 51 52 53 54 55 56 57 58 59 60  
W+25 W+26 W+27 W+28 W+29 W+30 W+31 W+32 W+33 W+34 W+35 W+36 W+37 W+38 W+39  
61 62 63 64 65 66 67 68 69 70 71 72 73 74 75  
W+40 W+41 W+42 W+43 W+44 W+45 W+46 W+47 W+48 W+49 W+50 W+51 W+52 W+53 W+54  
TV Display  
CATV channel  
TV Display  
CATV channel  
TV Display  
76  
77  
78  
79  
80  
81  
82  
83  
84  
85  
W+59 W+60 W+61 W+62 W+63 W+64  
100 101 102 103 104 105  
86  
87  
88  
89  
90  
W+55 W+56 W+57 W+58  
A-5  
95  
A-4  
96  
A-3  
97  
A-2  
98  
A-1  
99  
CATV channel  
TV Display  
91  
92  
93  
94  
CATV channel  
W+65 W+66 W+67 W+68 W+69 W+70 W+71 W+72 W+73 W+74 W+75 W+76 W+77 W+78 W+79  
TV Display  
106  
W+80 W+81 W+82 W+83 W+84  
121 122 123 124 125  
107  
108  
109  
110  
111  
112  
113  
114  
115  
116  
117  
118  
119  
120  
CATV channel  
TV Display  
- 35 -  
EN  
1C29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DVD SECTION  
ABOUT THE DISCS  
PLAYABLE DISCS  
DISC TYPES  
The following discs can be played back on this  
TV/VCR/DVD.  
[
]
DVD  
Data on a DVD is divided into sections called "titles" and  
then into subsections called "chapters", each of which is  
given a title or chapter number. Playback conditions are  
preset on some DVD video discs and these playback con-  
ditions take priority over user operations on this  
TV/VCR/DVD. If a function you selected does not run as  
desired, refer to the manual accompanying the disc.  
¡
¡
¡
¡
¡
¡
DVD video  
DVD+R/RW*  
CD-R/RW*  
DVD-R/RW*  
Audio CD  
MP3*  
* Depending on the types or the writing method of the  
medium some discs can not be played.  
Example  
• Some DVD-R/RW, DVD+R/RW, or CD-R/RW discs  
made on personal computers or on DVD recorders may  
not be played back properly due to the factors such as  
scratches, dirt or special properties of the disc.  
Title 1  
Title 2  
Chapter 1 Chapter 2 Chapter 3 Chapter 4 Chapter 1 Chapter 2  
• Discs made on personal computers may not be played  
back properly due to the different environment or the  
settings of the application you use. We recommend  
always to use the standardized, rightly formatted discs.  
(Please contact the sales agency for more detail).  
[
]
AUDIO CD  
This TV/VCR/DVD conforms to the NTSC color system.  
You cannot play discs recorded in other color systems  
such as PAL or SECAM.  
Data on an audio CD is divided into sections called  
“tracks”, each of which is given a track number.  
¡Some discs include region codes as shown below.  
Example  
Track 1  
Track 2  
Track 3  
Track 4  
Track 5  
Track 6  
¡The number inside the symbol refers to a region of the  
world, and a disc encoded in a specific region format  
can only be played back on TV/VCR/DVD with the  
same region code.  
The following discs cannot be played back on this  
TV/VCR/DVD.  
[
]
MP3  
Data on an MP3 is divided into sections called "groups",  
and then into subsections called "tracks", each of which is  
given a group or track number.  
¡
¡
¡
DVD with region codes other than 1 or ALL.  
DVD-ROM  
Example  
Group 1  
Group 2  
DVD-RAM (Never play back, otherwise malfunc-  
tion may result.)  
Track 1  
Track 2  
Track 3  
Track 4  
Track 5  
Track 6  
¡
¡
¡
¡
¡
CD-ROM  
VSD  
CDV (Only plays back the audio part.)  
CD-G (Only plays back the sound.)  
CD-I (Never play back, otherwise malfunction  
may result.)  
¡
¡
SACD  
Photo CD (Never play back, otherwise malfunc-  
tion may result.)  
¡
Video CD (Never play back, otherwise malfunc-  
tion may result.)  
Any other discs without compatibility indications.  
EN  
36  
01A11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PLAYING A DISC  
BASIC PLAYBACK  
GENERAL FEATURES  
DVD-V  
CD  
MP3  
DVD-V  
D
VD may contain menus to navigate the disc and  
Getting started  
access special features. Press the appropriate number  
buttons or use the Arrow button (K/L/s/B) to high-  
light your selection in the DVD main menu and press  
the ENTER button to confirm.  
¡Turn on the power of amplifier and any other com-  
ponents, if necessary.  
1
Press the POWER button.  
¡The power will turn on.  
NOTES  
¡Select DVD mode by pressing the SELECT button on  
the remote control. Then operate the DVD functions.  
¡Unless stated, all operations described are based on  
remote control use. Some operations can be carried  
out using the menu bar on the TV screen.  
2
3
Press the OPEN/CLOSE button to open disc  
loading tray.  
Place the chosen disc in the tray, with the  
label facing up.  
DISC MENU  
DVD-V  
1
Press the DISC MENU button.  
¡The DVD main menu will appear.  
2
3
If the feature is not available,  
may appear on the TV screen.  
symbol  
4
Press the PLAY button.  
¡The tray will close automatically and playback will  
then start from the first chapter or track of the disc.  
If the playback does not start automatically, press  
the PLAY button.  
If disc menu is available on the disc, audio lan-  
guage, subtitle options, chapters for the title  
and other options will appear for selection.  
¡When you playback a DVD which features a title  
menu, it may appear on the screen. In this case, refer  
to “TITLE MENU”.  
4
Press the Arrow button (K/L/s/B) to  
select an item and the ENTER button to  
confirm selection.  
5
Press the STOP button to stop playback.  
TITLE MENU  
DVD-V  
NOTES  
¡When the DVD mode has been switched to the  
TV/VCR mode, the DVD mode shuts down first and  
then TV picture and sound appears in about 4 seconds.  
Similarly, when the POWER button is pressed to turn  
off in the DVD mode, this mode shuts down first and  
then the TV/VCR/DVD’s power is turned off.  
¡A “prohibited icon” may appear at  
the top-right on the TV screen dur-  
ing operation, warning that a pro-  
hibited operation has been encoun-  
tered by the DVD or the disc.  
¡With DVDs that use titles for playback program sig-  
nals, playback may start from the second title, or it  
may skip these titles.  
¡During the playback of a two layered disc, pictures  
may stop for a moment. This happens when the 1st  
layer switches to the 2nd layer. This is not a mal-  
function.  
1
Press the TITLE button.  
¡The title menu will appear.  
2
3
If the feature is not available,  
may appear on the TV screen.  
symbol  
Press the Arrow button (K/L/s/B) to  
select an item and the ENTER button to  
confirm selection.  
CALLING UP A MENU SCREEN  
DURING PLAYBACK  
For DVD-Vs  
¡Press the DISC MENU button to call up the DVD menu.  
¡Press the TITLE button to call up the title menu.  
NOTE  
¡Contents of menus and corresponding menu opera-  
tions may vary between discs. Refer to the manual  
accompanying the disc for details.  
EN  
37  
01A11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FAST FORWARD/REVERSE  
SEARCH  
RESUME  
DVD-V  
CD  
MP3  
DVD-V  
CD  
MP3  
1
During playback, press the STOP button.  
¡Resume message will appear on the TV screen.  
1
During playback, press and hold the g or  
h button for a few seconds.  
¡g 1” or “h 1” appears on the screen.  
2
Press the PLAY button, playback will resume  
from the point at which playback was stopped.  
2
To select another speed, repeat step1 until  
your required speed appears on the screen.  
¡To cancel resume, press the STOP button twice.  
¡If TV/VCR/DVD is turned off, resume function will  
be cancelled.  
¡For MP3, playback will resume from the beginning  
of the track at which playback was stopped.  
¡For DVDs, fast forward/reverse search speed is dif-  
ferent depending on the disc. Approximate speed is  
1(×2), 2(×8), 3(×50) and 4(×100).  
¡For audio CDs, approximate speed is ×16.  
¡For MP3, approximate speed is ×8  
¡
When you use buttons on the TV/VCR/DVD front panel, use  
PAUSE  
the SKIP  
button.  
G/ SEARCH  
g
or SKIP  
H/ SEARCH  
h
DVD-V  
CD  
MP3  
3
To return to normal playback, press the  
PLAY button.  
1
During playback, press the PAUSE button.  
¡Playback will pause and sound will be muted.  
2
To continue playback, press the PLAY button.  
SLOW FORWARD /  
SLOW REVERSE  
STEP BY STEP PLAYBACK  
DVD-V  
DVD-V  
1
2
During playback, press the PAUSE button.  
1
During playback, press the PAUSE button.  
¡Playback will pause and sound will be muted.  
Press and hold the g or hbutton for a  
few seconds.  
¡“  
1” or “  
1” appears on the screen.  
2
3
The disc goes forward by one frame each  
time the PAUSE button is pressed.  
3
To select another speed, repeat step2 until  
your required speed appears on the screen.  
To exit step by step playback, press the  
PLAY button.  
¡Slow forward or reverse speed varies with the disc.  
Approximate speed is 1(1/16), 2(1/8) and 3(1/2).  
¡
When you use buttons on the TV/VCR/DVD front panel, use  
the SKIP  
button.  
G/ SEARCH  
g
or SKIP  
H/ SEARCH  
h
4
To return to normal playback, press the  
PLAY button.  
EN  
38  
01A11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SEARCH FUNCTION  
TRACK SEARCH  
TIME SEARCH  
CD  
MP3  
DVD-V  
CD  
There are three ways to begin playback on an Audio  
CD and MP3 at a specific track.  
1
2
During playback, press the SEARCH MODE  
button three times (CD: twice) to display the  
Time Search on the TV screen.  
Using the Number buttons on the remote control  
Within 30 seconds, enter a desired disc  
time using the Number buttons on the  
remote control.  
1
Press the Number buttons to enter the  
desired Track number.  
¡Playback will start at the selected track.  
¡For single digit tracks (1-9), press a single number  
(eg. track 3, press 3).  
¡Playback will start at the specified time.  
¡Press the CLEAR button to erase the incorrect input.  
¡When there is no need to enter a number, “0”  
appears automatically. For example, “ 0 : 0  
appears in the Time Search display if the total time  
of the disc is less than 10 minutes.  
¡To play track 26, press +10, 2, 6.  
:
-
- -  
Using the SEARCH MODE button  
MARKER SETUP SCREEN  
1
Press the SEARCH MODE button.  
¡The track search display appears.  
DVD-V  
CD  
2
Within 30 seconds, select a desired track  
number using the Number buttons on the  
remote control.  
Use markers to memorise your favorite places on a  
disc.  
¡For single digits press 0 first.  
¡Playback will start at the selected track.  
1
Press the SEARCH MODE button four times  
(CD: three times) during playback.  
Using the SKIP H G buttons  
¡The display screen and Markers will appear on the  
TV screen.  
During playback, press the SKIP G button to move  
the next track. Press it repeatedly to skip subsequent  
tracks. Press the SKIP H button to go back to begin-  
ning of the current track. Press it repeatedly to go to  
the previous tracks.  
¡If the SKIP button is pressed while the playback is  
paused, the playback will be paused again after skip-  
ping to the next track.  
2
3
Press the Arrow button (s/B) to select 1, 2,  
3, 4, 5, 6, 7, 8, 9, or 10 and ensure that “  
- - -  
:
:
” appears in the display.  
-
- - - -  
When you reach the desired point, press the  
ENTER button.  
NOTE  
¡The Title or Track and elapsed playing time will  
appear in the TV screen.  
¡The SKIP H G buttons are not available when  
playback is stopped.  
4
To return to the Marker later, press the  
SEARCH MODE button four times (CD: three  
times) during playback and the Arrow but-  
ton (s/B) to choose the desired marker,  
then press the ENTER button.  
TITLE / CHAPTER SEARCH  
DVD-V  
1
Press the SEARCH MODE button once for  
the Chapter search, twice for the Title  
search during playback.  
NOTES  
¡Opening the disc tray or turning off the power or  
selecting AC at step 2 and pressing the ENTER but-  
ton will erase all Markers.  
_/2  
¡To clear a marker, using the Arrow button (s/B),  
position the cursor on to the marker number to be  
cleared and press the CLEAR button.  
¡You can mark up to 10 points.  
2
Enter the desired chapter/title number using  
the Number buttons on the remote control.  
¡Playback will start at the selected Chapter or Track.  
¡Press the CLEAR button to erase the incorrect input.  
¡For single digits press 0 first.  
5
Press the SEARCH MODE or RETURN but-  
ton to exit.  
EN  
39  
01A11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SPECIAL PLAYBACK FUNCTION  
REPEAT  
PROGRAM  
REPEAT is available only during playback.  
CD  
You may determine the order in which tracks will play.  
REPEAT TITLE / CHAPTER  
DVD-V  
1
In stop mode, press the MODE button.  
¡The PROGRAM screen will appear.  
To activate the repeat function, press the  
REPEAT button during playback.  
¡The repeat mode changes as described below every  
time you press the button.  
2
Press the Arrow button or to select a  
track, then press the  
TOTAL  
CHAPTER  
(current chapter repeat) (current title repeat)  
TITLE  
OFF  
(repeat off)  
ENTER button.  
¡Press the CLEAR button to  
erase the most recently entered  
program.  
NOTES  
¡Repeat Title/Chapter is not available with some  
scenes.  
3
4
Repeat step 2 until you have selected all the  
tracks you want to play in the program.  
¡The REPEAT setting will be cleared when moving  
to other title or chapter.  
Press the PLAY button to play the pro-  
grammed tracks.  
REPEAT TRACK  
NOTES  
CD  
¡While the program is being played back, the STOP  
works as follows.  
To activate the repeat function, press the  
REPEAT button during playback.  
¡The repeat mode changes as described below every  
time you press the button.  
¡Press the STOP button once and then the PLAY but-  
ton again, playback will restart from the point where  
the STOP button was pressed. (Program continued)  
¡Press the STOP button twice and then the PLAY button  
again, playback will restart from the track in the usual  
way. (Program cleared)  
TRACK  
(current track repeat)  
ALL  
OFF  
(repeat off)  
(entire disc repeat)  
¡Up to 99 programs can be entered.  
¡To erase all programs at once, select ALL CLEAR at  
the bottom of the list at Step2.  
NOTES  
¡If you like to repeat the current track in the program,  
press the REPEAT button repeatedly until  
TRACK appears during playback. If you like to  
repeat the entire program press the REPEAT button  
¡Repeat setting will be cleared when moving to other  
track.  
¡Repeat playback does not function during repeat A-B  
playback.  
repeatedly until  
ALL appears during playback.  
REPEAT A-B  
RANDOM PLAYBACK  
DVD-V CD  
CD  
1
2
Press the REPEAT A-B button at your cho-  
sen starting point.  
A- appears briefly on the TV screen.  
This shuffles the playing order of tracks instead of  
playback in the sequence.  
¡
¡
1
In stop mode, press the MODE button twice.  
Press the REPEAT A-B button again at your  
chosen end point.  
¡RANDOM screen appears.  
RANDOM  
CD-DA  
TOTAL 0:45:55  
A-B appears briefly on the TV screen and the  
repeat sequence begins.  
RANDOM PROGRAM  
no indication  
-
-
-
-
PLAY  
3
To exit the sequence, press the REPEAT A-  
B button.  
NOTES  
2
Press the PLAY button to start random playback.  
NOTE  
¡The repeat A-B section can only be set within the cur-  
rent title (for DVDs) or current track (for audio CDs).  
¡Repeat A-B is not available with some scenes in DVD.  
¡To cancel the A point which was set, press the  
CLEAR button.  
¡If you like to repeat the current track in the random  
selection, press the REPEAT button repeatedly until  
TRACK appears during playback. If you like to  
repeat the entire random selection press the  
REPEAT button repeatedly until  
during playback.  
¡Repeat A-B playback does not function during title,  
chapter, track or all repeat playback.  
ALL appears  
EN  
40  
01A11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PLAYING A MP3 DISC  
MP3 PLAYBACK  
PROGRAM  
MP3  
MP3  
This feature allows you to program an MP3 disc to  
play in a desired sequence.  
When a CD with MP3 files is in the TV/VCR/DVD,  
press the DISC MENU button to call up the MP3 menu  
on the TV screen.  
1
In stop mode, press the MODE button.  
¡The PROGRAM screen will appear.  
1
In stop mode, press the Arrow button (K/L)  
to select the desired  
2
Select a desired track using the Arrow but-  
ton (K/L/s/B). Then press the ENTER  
button.  
group or track.  
folder name 1  
folder name 2  
¡If a group is selected, press  
the Arrow button or the  
folder name 3  
folder name 4  
file name 1  
file name 2  
file name 3  
B
¡Press the Arrow button B when you want to go to  
the next hierarchy.  
¡Press the Arrow button s when you want to go back  
to the previous hierarchy.  
¡Press the CLEAR button to erase the most recently  
entered program.  
ENTER button to go on to the  
track selection screen. Press  
the Arrow button (K/L) to  
choose a track, then press the ENTER button.  
¡If a track is selected, press the ENTER button to start  
playing tracks. Starting from the one you’ve just  
chosen the subsequent tracks will be played.  
folder name 1  
3
Repeat step 2 until you have selected all the  
Tracks you want to play in the program.  
¡Press the TITLE button to return to the first item.  
2
Press the STOP button to stop playback.  
NOTES  
4
Press the PLAY button to start programmed  
playback.  
¡Folders are known as Groups; files are known as  
Tracks.  
¡MP3 files are accompanied by  
NOTES  
¡While the program is being played back, the STOP  
button as follows.  
3
icon.  
¡Press the STOP button once and then the PLAY but-  
ton again, playback will restart from the point where  
the STOP button was pressed. (Program continued)  
¡Press the STOP button twice and then the PLAY button  
again, playback will restart from the track in the usual  
way. (Program cleared)  
¡Maximum of 255 folders can be recognized.  
¡Maximum of 512 files can be recognized.  
¡Up to 8 hierarchies can be created.  
This TV/VCR/DVD recommends the use of files  
recorded at the below specifications:  
¡Sampling frequency: 44.1kHz or 48kHz  
¡Constant bit rate: 112kbps ~ 320kbps.  
¡To erase all programs at once, select ALL CLEAR at  
the bottom of the list at Step2.  
REPEAT  
RANDOM PLAYBACK  
MP3  
MP3  
REPEAT is available only during playback.  
1
In stop mode, press the MODE button twice.  
¡RANDOM screen appears.  
To activate the repeat function, press the  
REPEAT button during playback.  
¡The repeat mode changes as described below every  
time you press the button.  
2
Press the PLAY button to start random play-  
back.  
TRACK  
(current track  
repeat)  
GROUP  
(current group  
repeat)  
ALL  
(entire disc  
repeat)  
OFF  
(repeat off)  
NOTE  
¡Repeat setting will be cleared when moving to other  
track.  
EN  
41  
01A11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CHANGING THE SETTINGS  
SUBTITLE LANGUAGE  
CAMERA ANGLE  
DVD-V  
DVD-V  
The TV/VCR/DVD allows you to select a language for Some DVD discs contain scenes which have been shot  
subtitles during DVD disc (if available) playback. simultaneously from various angles. You can change  
the camera angle when the (  
screen.  
) icon appears on the  
1
2
Press the SUBTITLE button during playback.  
Press the SUBTITLE button repeatedly to  
select your desired subtitle language.  
1
Press the ANGLE button during playback.  
¡The selected angle will be displayed on the display  
¡The subtitle language will appear on the display bar  
at the top of the TV screen.  
bar at the top of the screen.  
2
Press the ANGLE button repeatedly to  
select your desired angle.  
3
To turn off subtitles, press the SUBTITLE  
button repeatedly until OFF appears.  
NOTES  
BLACK LEVEL SETTING  
¡
Some discs allow audio language setting/subtitle language  
setting on the disc menu. (Operation varies between discs,  
so refer to the manual accompanying the disc.)  
DVD-V  
¡If the desired language is not shown after pressing  
the SUBTITLE button several times, the disc does  
not have subtitles in that language.  
Adjust the Black Level Settings to make the black  
parts of the picture brighter.  
¡If you choose a Language that has a 3 letter language  
code, the code will be displayed every time you  
change the Subtitle language setting. If you choose  
any other languages, ‘---’ will be displayed instead.  
(Refer to page 44.)  
1
Press the MODE button during playback.  
OFF  
2
Press the ENTER button to switch OFF.  
ON: Makes the dark parts brighter.  
AUDIO LANGUAGE  
OFF: Shows the original picture as recorded.  
DVD-V  
The TV/VCR/DVD allows you to select a language  
during DVD disc (if multi languages are available)  
playback.  
3
Press the MODE button twice or the  
RETURN button to exit.  
NOTE  
¡The setting will be saved even if the TV/VCR/DVD  
1
2
Press the AUDIO button during playback.  
is turned off.  
Press the AUDIO button repeatedly to select  
your desired language.  
VIRTUAL SURROUND  
NOTE  
DVD-V  
CD  
MP3  
¡Pressing the AUDIO button may not work on some  
DVDs with multiple audio languages (e.g. DVDs  
which allow audio language setting on the disc menu).  
You can enjoy surround-sound effect over two speak-  
ers on this TV/VCR/DVD.  
STEREO SOUND MODE  
1
Press the V.SURR button once or the MODE  
button twice (CD/MP3: once) during play-  
CD  
back.  
OFF  
1
Press the AUDIO button repeatedly during  
playback to select between STEREO, L-CH  
or R-CH.  
2
3
Press the ENTER button to set it 1 (Natural  
effect) or 2 (Emphasized effect) or OFF.  
¡
STEREO - both right and left channels are active (stereo)  
L-CH - only left channel is active  
R-CH - only right channel is active  
Press the V. SURR or RETURN button to  
exit.  
NOTE  
NOTE (for CD play only)  
¡Virtual Surround will not be effective if the sound  
mode is set to something other than STEREO.  
¡If the Virtual Surround setting is ON, the sound mode  
will be fixed to STEREO and can not be changed.  
EN  
42  
01A11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
THE ON-SCREEN INFORMATION  
DVD-V  
CD  
MP3  
You can check the information about the current disc by pressing the DISPLAY button on the remote control.  
For DVD-Vs  
For audio CDs  
1
Press the DISPLAY button during playback  
to show current Chapter.  
1
Press the DISPLAY button during playback  
to show the current Track.  
¡The elapsed and remaining  
playing time of the current  
chapter will be displayed.  
¡The elapsed and remaining playing time of the cur-  
rent track will be displayed.  
9/49  
0:00:00 -0:03:30  
2
Press the DISPLAY button again to show  
current Total Track.  
2
Press the DISPLAY button again to show  
current Title.  
¡The elapsed and remaining playing time of the cur-  
¡The elapsed and remaining playing time of the cur-  
rent track will be displayed.  
rent title will be displayed.  
3
Press the DISPLAY button again to exit the  
display.  
3
Press the DISPLAY button again.  
¡The BIT RATE and the current repeat setting will be  
displayed.  
For MP3  
¡If you are playing a dual layered disc, the layer num-  
ber will also be displayed (L0: Layer 0 is playing.  
L1: Layer 1 is playing).  
1
Press the DISPLAY button during playback.  
¡The name of the file currently in play will be dis-  
played.  
4
Press the DISPLAY button again to exit the  
display.  
2
Press the DISPLAY button again to show  
the track number, the elapsed time, the  
repeat status and the playback status at the  
top of the screen.  
¡
will be displayed when repeat play has been  
selected.  
T - indicates Track repeat  
G - indicates Group (folder) repeat  
A - indicates Disc repeat  
3
Press the DISPLAY button again to exit the  
display.  
EN  
43  
01A11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CHANGING THE DVD SETUP ITEMS  
LANGUAGE SETTING  
Language  
Code Language  
Code  
DVD-V  
A-B  
L-N  
Abkhazian  
Afar  
Afrikaans  
Albanian  
Amharic  
Arabic  
Armenian  
Assamese  
Aymara  
Azerbaijani  
Bashkir  
Basque  
Bengali;Bangla  
Bhutani  
Bihari  
Bislama  
Breton  
4748 Laothian  
4747 Latin  
4752 Latvian;Lettish  
6563 Lingala  
4759 Lithuanian  
4764 Macedonian  
5471 Malagasy  
4765 Malay  
5861  
5847  
5868  
5860  
5866  
5957  
5953  
5965  
5958  
5966  
5955  
5964  
5961  
5960  
6047  
6051  
6061  
Language options are not available with some discs.  
1
Press the SETUP button twice in STOP  
mode so that the DVD SETUP menu  
appears.  
4771 Malayalam  
4772 Maltese  
4847 Maori  
¡If the menu does not appear, press the PLAY button,  
the STOP button, then the SETUP button twice.  
5167 Marathi  
4860 Moldavian  
5072 Mongolian  
4854 Nauru  
SETUP  
QUICK  
CUSTOM  
INITIALIZE  
4855 Nepali  
4864 Norwegian [NOR]  
4853  
5971 Occitan  
4851 Oriya  
Oromo(Afan)  
5759 Panjabi  
4947 Pashto;Pushto  
7254 Persian  
4961 Polish  
5464 Portuguese [POR]  
4965 Quechua  
5047 Rhaeto-Romance  
6058 Romanian [RUM]  
5160 Russian [RUS]  
5161  
5166 Samoan  
Sangho  
5261 Sanskrit  
5256 Scots Gaelic  
5255 Serbian  
Bulgarian  
Burmese  
Byelorussian  
O-R  
6149  
6164  
6159  
6247  
6265  
5247  
6258  
6266  
6367  
6459  
6461  
6467  
C-E  
2
Press the Arrow button L to select CUS-  
Cambodian  
Catalan  
TOM, then press the ENTER button.  
Chinese [CHI]  
Corsican  
Croatian  
¡CUSTOM mode will appear.  
Czech  
3
Press the Arrow button (K/L) to select  
“LANGUAGE”, then press the ENTER button  
to confirm.  
Danish [DAN]  
Dutch [DUT]  
English [ENG]  
Esperanto  
Estonian  
S
6559  
6553  
6547  
5350  
6564  
6554  
6566  
6660  
6560  
6550  
6555  
6565  
6557  
6558  
6561  
5165  
6567  
6569  
6568  
SETUP  
CUSTOM  
F-H  
Faroese  
Fiji  
LANGUAGE  
DISPLAY  
AUDIO  
Finnish [FIN]  
French [FRE]  
Frisian  
PARENTAL  
5264 Serbo-Croatian  
5271 Sesotho  
5358 Setswana  
5747 Shona  
Galician  
Georgian  
German [GER]  
Greek [GRE]  
Greenlandic  
Guarani  
4
Press the Arrow button (K/L) to select the  
next items, then press the ENTER button.  
5051 Sindhi  
5158 Singhalese  
5758 Siswat  
5360 Slovak  
AUDIO: Sets the audio language.  
Gujarati  
Hausa  
Hebrew  
5367 Slovenian  
5447 Somali  
5569 Spanish [SPA]  
5455 Sundanese  
5467 Swahili  
SUBTITLE: Sets the subtitle language.  
DISC MENU: Sets the language for DVD menu.  
Hindi  
Hungarian [HUN]  
I-K  
Icelandic [ICE]  
Indonesian  
Interlingua  
Interlingue  
Inupiak  
5
Press the Arrow button (K/L) to select a  
setting, then press the ENTER button.  
Swedish [SWE]  
5565  
5560 Tagalog  
5547 Tajik  
5551 Tamil  
5557 Tatar  
5347 Telugu  
5566 Thai  
T
6658  
6653  
6647  
6666  
6651  
6654  
4861  
6655  
6661  
6665  
6664  
6657  
6669  
¡If OTHER is selected on the AUDIO, SUBTITLE or  
DISC MENU screen, press four-digit number to  
enter the code for the desired language. (Refer to the  
language code list.)  
¡Only the languages supported by the disc can be  
selected.  
Irish [IRI]  
Italian [ITA]  
Japanese [JPN]  
Javanese  
Kannada  
Kashmiri  
5647 Tibetan  
5669 Tigrinya  
5760 Tonga  
5765 Tsonga  
5757 Turkish [TUR]  
6469 Turkmen  
5771 Twi  
Kazakh  
6
Press the SETUP button to exit.  
Kinyarwanda  
Kirghiz  
Kirundi  
NOTE  
6460  
U-Z  
¡Language Setting for Audio and Subtitle is not avail-  
able with some discs. Then use the AUDIO and the  
SUBTITLE buttons. Details are on page 42.  
Korean [KOR]  
Kurdish  
5761 Ukrainian  
5767 Urdu  
Uzbek  
6757  
6764  
6772  
6855  
6861  
4971  
6961  
7054  
5655  
7161  
7267  
Vietnamese  
Volapuk  
Welsh  
Wolof  
Xhosa  
Yiddish  
TO CHANGE THE ON-SCREEN MENUS  
You can access the TV/VCR SETUP menu by pressing  
the SETUP button from the DVD mode. Refer to  
“SELECTING THE LANGUAGE” on page 15 to  
changing the on-screen menus.  
Yoruba  
Zulu  
If you choose a Language that has a 3 letter language  
code, the code will be displayed every time you change  
the Audio or Subtitle language setting on page 42. If  
you choose any other languages, ‘---’ will be displayed  
instead. (3 letter language code is written in bracket.)  
EN  
44  
01A11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DISPLAY SETTING  
AUDIO SETTINGS  
DVD-V  
DVD-V  
You can change certain aspects of the DVD display Choose the appropriate Audio settings for your equip-  
screens and on-screen messages on the TV screen.  
ment as it only affects during the playback of DVD  
discs.  
1
Press the SETUP button twice in STOP mode  
so that the DVD SETUP menu appears.  
1
Press the SETUP button twice in STOP mode  
so that the DVD SETUP menu appears.  
¡If the menu does not appear, press the PLAY button,  
the STOP button, then the SETUP button twice.  
¡If the menu does not appear, press the PLAY button,  
the STOP button, then the SETUP button twice.  
SETUP  
SETUP  
QUICK  
CUSTOM  
INITIALIZE  
QUICK  
CUSTOM  
INITIALIZE  
2
Press the Arrow button L to select CUS-  
TOM, then press the ENTER button.  
¡CUSTOM mode will appear.  
2
Press the Arrow button L to select “CUS-  
TOM”, then press the ENTER button.  
3
Press the Arrow button (K/L) to select “DIS-  
PLAY”, then press the ENTER button to con-  
firm.  
¡CUSTOM mode will appear.  
3
Press the Arrow button (K/L) to select  
“AUDIO”, then press the ENTER button to  
confirm.  
SETUP  
CUSTOM  
LANGUAGE  
DISPLAY  
AUDIO  
PARENTAL  
SETUP  
CUSTOM  
LANGUAGE  
DISPLAY  
AUDIO  
4
Press the Arrow button (K/L) to select the  
below items, then press the ENTER button.  
PARENTAL  
TV MODE:  
QUICK  
4
Press the Arrow button (K/L) to select the  
below items, then press the ENTER buttons.  
¡Press the Arrow button (K/L) for an item selection,  
then press the ENTER button.  
¡Select 4:3 LETTER BOX for black bars to appear on  
top and bottom of the screen.  
DRC (Dynamic Range Control):  
¡To compress the range of soft to loud sound.  
¡The default setting is ON.  
¡Select 4:3 PAN & SCAN for a full height picture  
with both sides trimmed.  
¡The default setting is 4:3 LETTER BOX.  
DOWN SAMPLING:  
¡Set to ON when outputting in 48 kHz.  
¡The default setting is ON.  
When playing disc with copyright Protection  
¡If you select OFF, copyright protection will be acti-  
vated and sound will be down sampled at 48kHz.  
STILL MODE  
:
¡Press the Arrow button (K/L) for an item selection,  
then press the ENTER button.  
¡Select “AUTO” usually.  
¡If you select “FIELD”, the picture in the still mode  
will be stabilized.  
¡If you select “FRAME”, the picture in the still mode  
will be highly defined.  
DOLBY DIGITAL:  
QUICK  
ANGLE ICON:  
Set to On when the unit is connected to a Dolby Digital  
Decoder.  
¡Press the ENTER button repeatedly to turn Angle  
icon ON or OFF.  
(ON: Output a Dolby Digital signal)  
(OFF: Convert the Dolby Digital to PCM (2 channel  
stereo))  
¡The default setting is ON.  
AUTO POWER OFF:  
¡Press the ENTER button repeatedly to turn Auto  
Power off ON or OFF.  
¡The default setting is ON.  
¡
The default setting is ON and it will turn the  
TV/VCR/DVD off automatically after 15 minutes of no  
use.  
5
Press the SETUP button to exit.  
5
Press the SETUP button to exit.  
EN  
45  
01A11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONTROL LEVELS  
PARENTAL CONTROL  
¡
ALL  
All parental lock is cancelled.  
DVD-V  
¡
Level 8  
DVD software of any grade (adult/general/children)  
can be played back.  
Parental Control limits the disc viewing that exceed  
your settings. (with a password or playback will stop.)  
This feature allows you to prevent discs with alterna-  
tive scenes from being played by your children.  
¡
Levels 7 to 2  
Only DVD software intended for general use and  
children can be played back.  
PARENTAL LEVEL  
¡
Level 1  
Parental Level allows you to set the rating level of  
your DVD discs. Playback will stop if the disc’s rat-  
ings exceed the level you set.  
Only DVD software intended for children can be  
played back, with those intended for adult and  
general use is prohibited.  
1
Press the SETUP button twice in STOP mode  
so that the QUICK SETUP menu appears.  
¡If the menu does not appear, press the PLAY button,  
the STOP button, then the SETUP button twice.  
IF YOU FORGET THE PASSWORD  
1
Press the number buttons 4, 7, 3, 7 at step 4.  
Then enter your new password.  
2
Press the Arrow button L to select “CUS-  
TOM”, then press the ENTER button.  
SETUP  
¡Password will be cleared and parental level will be  
set to ALL.  
QUICK  
CUSTOM  
INITIALIZE  
2
Proceed the Steps 5-7 again.  
3
Press the Arrow button (K/L) to select  
PARENTAL, then press the ENTER button.  
INITIALIZE  
SETUP  
CUSTOM  
This allows you to return all selections of SETUP  
(except for PARENTAL) to their default settings.  
LANGUAGE  
DISPLAY  
AUDIO  
PARENTAL  
1
2
3
Press the SETUP button twice in STOP  
mode so that the INITIALIZE menu appears.  
Press the Arrow button (K/L) to select “INI-  
TIALIZE”, then press the ENTER button.  
4
5
Enter your four-digit password then press  
the ENTER button.  
Select “YES”, then press the ENTER button  
twice. All the settings (except for  
PARENTAL) will be cleared.  
Press the Arrow button (K/L) to select  
PARENTAL LEVEL, then press the ENTER  
button.  
¡To cancel the initialization, select “NO”.  
6
7
Press the Arrow button (K/L) to select the  
desired level, then press the ENTER button.  
4
Press the SETUP button to exit.  
Press the SETUP button to exit  
NOTES  
¡When doing this for the first time, enter any 4 digits.  
(except for 4737) That number will be used as the  
password.(in the event you forget the password, see  
below)  
¡To change the password, press the Arrow button  
(K/L) to select CHANGE at step 5, then press the  
ENTER button. Enter the four-digit password, then  
press the ENTER button.  
¡With some DVDs, it may be difficult to find if they  
are compatible with parental lock. Be sure to check  
if the parental lock function operates in the way that  
you have set.  
¡Record the password in case you forget it.  
EN  
46  
01A11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TROUBLESHOOTING GUIDE  
If the TV/VCR/DVD does not perform properly when operated as instructed in this Owner’s Manual, check  
the TV/VCR/DVD, consulting the following checklist.  
PROBLEM  
CORRECTIVE ACTION  
Make sure the power plug is connected to an AC outlet.  
Make sure the power is turned on.  
Check if the power plug is connected to an AC outlet.  
Check the batteries in the remote control.  
Aim the remote control directly at the remote sensor. If necessary,  
remove all the obstacles between the sensor and the remote.  
You have to be within 23 feet of the TV/VCR/DVD.  
No power  
The TV/VCR/DVD does not  
respond to the remote control  
Check if the correct mode is selected. If not switch the mode by  
pressing the SELECT button on the remote control,whichever you need.  
TV/VCR Mode  
Sometimes a performance problem can be easily solved by checking seemingly apparent but often overlooked  
possibilities. Before arranging for service, check these items. It could save your time and money.  
PROBLEM  
No picture and sound  
CORRECTIVE ACTION  
Make sure the AC cord is connected to an AC outlet.  
Check antenna connection.  
Press the SELECT button on the remote control to select TV mode.  
Then try other TV feature.  
Let the TV/VCR/DVD program its tuner memory.  
Adjust direction or replace antenna.  
Adjust picture controls.  
Adjust volume control on remote control or main unit.  
Press the MUTE button to restore sound.  
If outside antenna is being used, check for broken wire.  
Check for local interference.  
Try a new channel, if OK, then possible station trouble.  
If outside antenna is being used, check for broken wire.  
Try a new channel, if OK, then possible station trouble.  
If outside antenna is being used, check for broken wire.  
Check for local interference.  
Try a new channel, if OK, then possible station trouble.  
Is antenna connected to terminal on the back of the set?  
If outside antenna is being used, check for broken wire.  
Adjust COLOR control.  
Try a new channel, if OK, then possible station trouble.  
Is antenna connected to terminal on the back of the set?  
If outside antenna is being used, check for broken wire.  
Check for local interference.  
Try a new channel, if OK, then possible station trouble.  
Is antenna connected to terminal on the back of the set?  
If outside antenna is being used, check for broken wire.  
Adjust CONTRAST & BRIGHT control.  
No picture or poor picture on  
TV/VCR/DVD  
No sound or poor sound  
Bars On Screen  
Picture Distorted or Blurred  
Picture Rolls Vertically  
Lines or Streaks in Picture  
No Color  
Poor Reception on Some Channels  
Ghosts in Picture  
Weak Picture  
Sound OK, Picture Poor  
Try a new channel, if OK, then possible station trouble.  
Is antenna connected to terminal on the back of the set?  
If outside antenna is being used, check for broken wire.  
Check for local interference.  
Adjust CONTRAST & BRIGHT control.  
EN  
47  
01A11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PROBLEM  
Picture OK, Sound Poor  
CORRECTIVE ACTION  
Try a new channel, if OK, then possible station trouble.  
Check for local interference.  
Make sure the timer recording is set correctly.  
Make sure the power is off.  
Make sure the TV/VCR/DVD clock is set correctly.  
Make sure the tape has an erase-prevention tab. If need, cover the  
hole with plastic tape.  
Timer recording is not possible  
Cannot go into Record mode  
Playback picture is partially noisy  
Adjust tracking control for a better picture using the CHANNEL  
button K or L on the TV/VCR/DVD.  
Head cleaning may be necessary. Refer to “AUTO HEAD  
CLEANING” on page 50.  
No picture but the audio is OK in  
playback  
No operation by infrared Remote  
Control  
Video or color fades in and out  
Make sure the AC cord is connected to an AC outlet.  
Check batteries in remote control.  
You can not copy a copyrighted video tape. You are experiencing  
when making a copy of a video tape copy guard protection.  
Different color marks on screen  
Magnetism from nearby appliances and geomagnetism might affect  
the color of the TV picture. Move the  
away from the  
TV/VCR/DVD  
appliances, the  
can repair itself automatically. If you  
TV/VCR/DVD  
want to repair immediately, turn off using the POWER button, then  
turn it on again 30 minutes later or so.  
CLOSED CAPTION PROBLEM  
My TV/VCR/DVD is showing  
captions that are misspelled.  
POSSIBLE REMEDY  
You are watching a live broadcast and spelling errors made by the  
closed captioning production company may pass through uncorrected.  
A prerecorded program will not show any misspelled words because  
of the normal time available for editing the captions.  
My TV/VCR/DVD will not show  
the text dialogue in its entirety or  
• Captions that are delayed a few seconds behind the actual  
are common for live broadcast. Most captioning production  
there is a delay of what is being said. companies can display a dialogue to a maximum of 220 words  
per minute. If a dialogue exceeds that rate, selective editing is used  
to insure that the captions remain up-to-date with the current  
TV screen dialogue.  
My captions are scrambled with  
white boxes on the TV screen.  
• Interference caused by building, power lines, thunderstorms, etc.  
may cause scrambled or incomplete captions to appear.  
My program guide listed a TV show • Broadcasters may at times use a time compression process to speed  
as being closed captioned but none up the actual program so that additional advertising time can be  
of the captions were displayed.  
given. Since the decoder cannot read the compressed information,  
captions will be lost.  
My prerecorded video tape does not • The video tape was either an illegal copy or the tape duplicating  
show any captions. The tape box company accidentally left out the captioning signals during the  
mentions it being closed captioned. copying process.  
My TV screen shows a black box  
on certain channels.  
You are in the TEXT mode. Select CAPTION mode to CAPTION  
[OFF].  
EN  
48  
01A11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DVD Mode  
PROBLEM  
CORRECTIVE ACTION  
• Insert a correct video disc that plays on this TV/VCR/DVD.  
• Press the SELECT button on the remote control to select DVD mode.  
Then, try other DVD feature.  
No picture  
• Insert the disc.  
Disc cannot be played  
• Clean the disc.  
• Place the disc correctly, with the label side up.  
• Cancel the parental lock or change the control level.  
• Connect the audio cables firmly.  
No sound  
• Turn the power of the audio component on.  
• Correct the audio output settings.  
• Correct the input settings on the audio component.  
• This TV/VCR/DVD does not support DTS audio. This is not a mal-  
function.  
• There are some cases where pictures may be slightly distorted, which  
are not a sign of a malfunction.  
No DTS audio is output  
Distorted picture  
• Although pictures may stop for a moment, this is not a malfunction.  
Audio or subtitle language  
does not match the set up  
The selected language is not available for audio or subtitles on the DVD.  
This is not a malfunction  
The camera angle cannot be changed • The DVD does not contain sequences recorded from different camera  
angles. This is not a malfunction  
Audio or subtitle language cannot be • The DVD does not contain audio source or subtitles in the selected  
changed  
language. This is not a malfunction.  
“Prohibited icon” appears on the  
screen, prohibiting an operation  
CD sound dropout  
• That operation is prohibited by this TV/VCR/DVD or the disc.  
This is not a malfunction.  
• Scratched disc. Replace the disc with an unscratched one.  
No CD reproduction  
DVD picture dropout  
DVD picture freeze  
DVD picture in mosaic  
No DVD reproduction  
NOTES:  
Some functions are not available in specific modes, but this is not a malfunction. Read the description in  
this Owner’s Manual for details on correct operations.  
Playback from a desired track and random playback are not available during program playback.  
EN  
49  
01A11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE  
1.Please visit your local Audio/Video store and pur-  
CABINET CLEANING  
chase a good quality VHS Video Head Cleaner.  
2.If a Video Head Cleaner does not solve the prob-  
lem, please call our help line at 1-800-968-3429, to  
locate an Authorized Service Center.  
Wipe the front panel and other exterior surfaces of  
the TV/VCR/DVD with a soft cloth immersed in  
lukewarm water and wrung dry.  
Never use a solvent or alcohol. Do not spray insec-  
NOTES:  
ticide liquid near the TV/VCR/DVD. Such chemi-  
cals may cause damage and discoloration to the  
exposed surfaces.  
Remember to read the instructions included with  
the video head cleaner before use.  
Clean video heads only when problems occur.  
AUTO HEAD CLEANING  
SERVICING  
Automatically cleans video heads as you insert or  
remove a cassette, so you can see a clear picture.  
Should your TV/VCR/DVD become inoperative,  
do not try to correct the problem by yourself. There  
are no user-serviceable parts inside. Turn off,  
unplug the power cord and please call our help line  
at 1-800-968-3429, to locate an Authorized Service  
Center.  
Playback picture may become blurred or interrupt-  
ed while the TV program reception is clear. Dirt  
accumulated on the video heads after long periods  
of use or the usage of rental or worn tapes can  
cause this problem.  
If a streaky or snowy picture appears during play-  
back, the video heads in your TV/VCR/DVD may  
need to be cleaned.  
IF THE LASER OPTICAL PICKUP UNIT IS DIRTY  
If the TV/VCR/DVD still does not perform properly when it is operated while referring to the relevant sections  
and to "TROUBLESHOOTING GUIDE" in this Owner's Manual, the laser optical pickup unit may be dirty.  
Consult your dealer or an Authorized Service Center for inspection and cleaning of the laser optical pickup unit.  
DISC HANDLING  
Use discs which have the following logos on them.  
(Optical audio digital discs.)  
To clean-off, use a soft cloth.  
Do not use a hard cloth since this will mar the disc.  
Wipe the disc in a straight line from center to edge.  
Never wipe with a circular motion.  
ReWritable  
Recordable  
Do not use detergent or abrasive cleaning agents.  
Handle the discs so that fingerprints and dust do  
not adhere to the surfaces of the discs.  
Always store the disc in its protective case when it  
is not used.  
EN  
50  
01A11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SPECIFICATIONS  
GENERAL SPECIFICATIONS  
ELECTRICAL SPECIFICATIONS  
Sound output:  
2 speakers, 1W, 8 ohm  
TV/VCR  
CRT  
27 inch in-line gun,  
90˚ deflection tube  
NTSC-M  
OTHER SPECIFICATIONS  
Terminals  
Television system :  
Closed caption system :§15.119/FCC  
Antenna input:  
VHF/UHF/CATV  
75 ohm unbalanced (F-type)  
RCA connector [ 1  
RCA connector [ 2  
Video Heads :  
Tape width :  
Tape speed  
SP :  
LP :  
SLP :  
Tuner channel  
TV VHF Low :  
TV VHF High :  
TV UHF :  
CATV  
Rotary four-head  
1/2 inch  
Video input:  
Audio L/R input:  
Headphone:  
Coaxial digital  
audio output:  
1/8” stereo (3.5 mm)  
33.40mm/sec.  
16.67mm/sec.  
11.12mm/sec.  
One pin jack,  
500m Vpp (75 ohm)  
Digital encoded  
Remote control:  
#2~#6  
#7~#13  
#14~#69  
infrared light system  
Operating  
temperature:  
5°C to 40°C  
(41°F~104°F)  
Power requirements: AC 120V, 60Hz  
Power consumption  
VHF :  
5A  
MID band :  
SUPER band :  
HYPER band :  
A5~A1, A~I  
J~W  
W+1~W+84  
(Maximum):  
Picture tube:  
Dimensions:  
110W  
27"  
H:25-1/2” (648mm)  
W:29-9/16” (675mm)  
D:19-11/16” (500mm)  
86 lbs (39.0kg)  
Weight:  
DVD  
Product type:  
Discs:  
DVD Player  
DVD video, Audio CD  
Output signal format: NTSC color  
Designs and specifications are subject to change without notice.  
If there is a discrepancy between languages, the default language will be English.  
EN  
51  
01A11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
12. Indicador de grabación  
INDICE  
Parpadea durante la grabación. Se ilumina durante el  
modo de espera de grabación controlada por temporizador.  
CONTROLES DE OPERACIÓN Y FUNCIONES . . . . . 52  
PANEL FRONTAL DEL TELEVISOR/DVD. . . . . . . . . . 52  
MANDO A DISTANCIA. . . . . . . . . . . . . . . . . . . . . . . . . 52  
VISTA POSTERIOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52  
PREPARACIÓN PARA LA UTILIZACIÓN . . . . . . . . . . 53  
CONEXIONES DE ANTENA/CABLE . . . . . . . . . . . . . . 53  
CONEXIÓN A TOMAS DE ENTRADA EXTERNA. . . . 53  
PARA INSERTAR LAS PILAS . . . . . . . . . . . . . . . . . . . . 54  
MODO DE ENTRADA EXTERNA . . . . . . . . . . . . . . . . 54  
CONEXIÓN A UN SISTEMA ESTÉREO . . . . . . . . . . . . 54  
CONEXIÓN A UN AMPLIFICADOR ESTÉREO  
13. Botón REC/OTR (Panel frontal)[TV/VCR P.30, 31]  
Presione para empezar la grabación manual. Presione  
repetidamente para empezar la grabación instantánea  
(OTR).  
Botón RECORD (Mando a distancia)[TV/VCR P.30]  
Presione para empezar la grabación manual.  
14. Botón REW (para TV/VCR)  
Presione este botón para rebobinar la cinta o para ver  
la imagen rápidamente en dirección de retroceso  
durante el modo de reproducción. (Búsqueda en direc-  
ción de retroceso)  
EQUIPADO CON TOMAS DE ENTRADA DIGITAL,  
PLATINA MD O PLATINA DAT (Para DVD). . . . . . . . . 54  
CONEXIÓN A UN DECODIFICADOR DOLBY DIGITAL  
(para DVD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54  
15. Botón F.FWD (para TV/VCR)  
Presione este botón para adelantar rápidamente la cinta  
o para ver la imagen rápidamente en dirección de  
avance durante el modo de reproducción. (Búsqueda en  
dirección de avance)  
SECCIÓN DE TV/VCR  
PREPARACIÓN PARA LA UTILIZACIÓN . . . . . . . . . . 54  
SELECCIÓN DE IDIOMA . . . . . . . . . . . . . . . . . . . . . . . 54  
AJUSTE DE CANALES . . . . . . . . . . . . . . . . . . . . . . . . . 55  
AJUSTE DEL RELOJ . . . . . . . . . . . . . . . . . . . . . . . . . . . 55  
16. Botón STOP/EJECT  
Presione este botón para detener la cinta. Presiónelo en  
el modo de parada para retirar la cinta del  
televisor/videograbadora/DVD.  
SECCIÓN DE DVD  
REPRODUCCIÓN BÁSICA . . . . . . . . . . . . . . . . . . . . . . 55  
17. Ventanilla del sensor de mando a distancia  
18. Toma HEADPHONE  
Para conectar auriculares (no suministrados) y escuchar  
en privado.  
CONTROLES DE  
19. Toma de entrada VIDEO  
OPERACIÓN Y FUNCIONES  
Conecte aquí la toma de salida de vídeo de una  
videocámara o de una videograbadora.  
PANEL FRONTAL DEL  
TELEVISOR/DVD  
20. Tomas de entrada AUDIO L/R  
Conecte aquí las tomas de salida de audio de una  
videocámara o de una videograbadora.  
Consulte la figura 1 de la página 9  
21. Compartimiento del cassette  
22. Botón PICTURE  
MANDO A DISTANCIA  
Presione este botón para ajustar la imagen.  
23. Botones numéricos  
Consulte la figura 2 de la página 9  
Modo TV:  
Presione dos botones para acceder directamente al  
canal deseado.  
VISTA POSTERIOR  
No olvide presionar “0” antes de elegir un canal de un  
solo dígito.  
Consulte la figura 3 de la página 10  
Botón +100  
1. Botón POWER  
Presione este botón para conectar y desconectar la ali-  
mentación.  
2. Botones VOLUME X/Y  
Presione estos botones para controlar el nivel de volumen  
del DVD y el televisor.  
Presione este botón para seleccionar canales de tele-  
visión por cable cuyo número sea igual o superior a 100.  
Modo DVD:  
Presione este botón para introducir el número deseado.  
Botón +10  
Presione este botón para introducir números iguales o  
3. Botones SKIP (para DVD)  
mayores que 10  
.
Presione el botón correspondiente una vez para omitir  
capítulos o pistas y desplazarse a un punto específico.  
Mantenga el botón presionado para cambiar la veloci-  
dad de reproducción en avance o retroceso.  
24. Botón PAUSE  
Hace una pausa en la reproducción del disco o cinta.  
25. Botón SPEED  
Presione este botón para seleccionar la velocidad de  
grabación deseada: SP/SLP.  
4. Botón PLAY  
Inicia la reproducción del contenido del disco o cinta.  
5. Botón STOP  
Detiene la reproducción del disco.  
6. Botón OPEN/CLOSE  
Presione este botón para insertar discos en la bandeja o  
retirarlos de ella.  
26. Botón C.RESET  
Presione este botón para poner el contador en 0:00:00.  
Presiónelo también para cancelar un ajuste de progra-  
ma de temporizador.  
27. Botón DISPLAY  
Modo TV/VCR:  
7. Bandeja de carga del disco  
Para visualizar el contador o el número del canal y la  
fecha actual en la pantalla del televisor.  
Modo DVD:  
8. Indicador DVD  
Se ilumina durante el modo DVD.  
Indica el estado actual en la pantalla del televisor para  
fines de comprobación.  
9. Botón SELECT  
Presione este botón para cambiar al modo TV/VCR,  
modo de entrada externa o modo de DVD.  
28. Botón SETUP  
Presione este botón para activar o salir del modo de  
menús de televisor o configuración de DVD.  
10. Indicador TV/VCR  
Se ilumina durante el modo TV/VCR.  
29. Botón TITLE  
11. Botones CHANNEL K/L  
Para visualizar el menú de títulos.  
Utilice estos botones para seleccionar canales memorizados.  
ES  
52  
0C28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
30. Botón CLEAR  
ANTENAS SEPARADAS DE VHF/UHF  
En algunas zonas será necesario utilizar una antena  
exterior.  
TELEVISIÓN POR CABLE SIN CAJA DE  
CONVERTIDOR/DECODIFICADOR  
Utilice esta conexión si su sistema de televisión por  
cable se conecta directamente a su televisor/  
videograbadora/DVD, sin una caja de convertidor.  
Con esta conexión podrá:  
Para cancelar ajustes.  
31. Botón MODE  
Activa el modo de reproducción programada o el modo de  
reproducción aleatoria.  
32. Botón SEARCH MODE  
Presione este botón para localizar un punto deseado.  
33. Botón AUDIO  
Presione este botón para seleccionar un idioma de  
audio o el modo de sonido deseado.  
1) Utilizar el mando a distancia del televisor/  
videograbadora/DVD para seleccionar canales.  
2) Programar uno o más canales decodificados para  
grabación automática controlada por temporizador.  
NOTA: Este televisor/videograbadora/DVD SÓLO  
puede grabar el canal que se está viendo.  
34. Botón SUBTITLE  
Presione este botón para seleccionar el idioma de subtí-  
tulos deseado.  
35. Botón REPEAT  
Repite la reproducción del disco, título, capítulo o pista actual.  
36. Botón ANGLE (modo DVD)  
Presione este botón para cambiar el ángulo de la cámara  
y ver la secuencia que se está reproduciendo desde un  
ángulo diferente.  
TELEVISIÓN POR CABLE CON CAJA  
DE CONVERTIDOR/DECODIFICADOR  
O CAJA DE SATÉLITE  
37. Botón A-B REPEAT  
Si su compañía de televisión por cable le suministra  
una caja de convertidor o si utiliza un sistema de  
satélite, podrá utilizar la conexión básica que se  
muestra en la ilustración.  
Repite la reproducción de una sección seleccionada.  
38. Botón RETURN  
Permite volver a la operación anterior en el modo de  
configuración de DVD.  
Al utilizar esta conexión, también podrá grabar canales  
codificados. Sin embargo, la selección de los canales  
deberá hacerse con la caja de convertidor o con la caja  
de satélite. Esto significa que no es posible cambiar de  
canal utilizando el mando a distancia del televisor/  
videograbadora/DVD. La grabación en ausencia (contro-  
lada por temporizador) está limitada a un canal a la vez.  
PARA GRABAR UN CANAL  
39. Botón ENTER  
Presione este botón para establecer un ajuste.  
40. Botones de flechas  
Modo TV/VCR:  
Presione estos botones para seleccionar un modo de  
ajuste en el menú que aparece en la pantalla del televisor.  
Presiónelos también para seleccionar opciones o  
establecer ajustes en un menú en particular.  
Modo DVD:  
CODIFICADO/DECODIFICADO  
Use estos botones para hacer ajustes mientras observa  
la imagen en la pantalla del televisor.  
1.Ajuste el selector de canales del  
televisor/videograbadora/DVD al canal de salida de  
la caja de convertidor de televisión por cable o caja  
de satélite. (Ej., CH3)  
41. Botón DISC MENU  
Muestra los menús contenidos en el DVD.  
42. Botón V.SURR  
2.Seleccione el canal que desea grabar en la caja de  
convertidor de televisión por cable o caja de satélite.  
Activar/desactivar el envolvente virtal.  
43. Botón MUTE  
Suprime la salida de sonido. Presiónelo de nuevo para  
restablecer el sonido.  
Nota para el instalador de sistemas CATV  
Esta nota tiene la finalidad de llamar la atención  
del instalador de sistemas CATV para que tenga  
en cuenta el Artículo 820-40 de la NEC, que pro-  
porciona recomendaciones para hacer una conex-  
ión a tierra apropiada y, en particular, especifica  
que la tierra del cable debe conectarse al sistema  
de puesta a tierra del edificio, tan cerca del punto  
de entrada del cable como sea posible.  
44. Botón SLEEP  
Utilice este botón para ajustar el temporizador de dormir.  
45. Botón SELECT  
Presione este botón para cambiar entre los modos  
TV/VCR y DVD. El modo seleccionado (TV/VCR o  
DVD) se visualiza en el indicador del panel delantero.  
46. Toma de entrada ANT.  
Conéctela a una antena, sistema de televisión por cable  
o sistema de satélite.  
CONEXIÓN A TOMAS DE ENTRADA  
EXTERNA  
47. Cable de alimentación  
Conéctelo a una toma de CA estándar (120 V, /60 Hz).  
NOTA: Antes de conectar el cable de alimentación a  
una toma de CA estándar, retírelo del gancho  
para evitar dañarlo.  
Cuando vea un programa grabado en otra fuente (videograbado-  
ra o videocámara), utilice las tomas de entrada de audio/vídeo  
de la parte delantera del televisor/videograbadora/DVD.  
Conecte las tomas de salida de audio/vídeo de otra fuente a  
las tomas AUDIO L/R y VIDEO de este televisor/  
videograbadora/DVD. Luego, presione los botones CHAN-  
NEL K/L hasta que aparezca "AUX" en la pantalla.  
NOTA:  
48. Toma de salida de audio digital COAXIAL  
Conéctela solamente a la entrada digital de un amplifi-  
cador externo o decodificador de audio de DVD.  
PREPARACIÓN PARA LA  
UTILIZACIÓN  
CONEXIONES DE ANTENA/CABLE  
Cuando conecte una videograbadora monofónica (otra  
fuente) a este televisor/videograbadora/DVD, conecte la  
toma de salida de audio de la videograbadora monofónica  
(otra fuente) a la toma AUDIO L de este  
televisor/videograbadora/DVD. El audio saldrá igual-  
mente por los canales izquierdo y derecho.  
Consulte la figura 4 de la página 11  
Consulte la figura 5 de la página 12  
ES  
53  
0C28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Consulte la figura 7 de la página 14  
NOTAS:  
PARA INSERTAR LAS PILAS  
1) Abra la cubierta del compartimiento de las pilas  
empujando la cubierta del mando a  
distancia en el sentido de la flecha.  
2) Inserte 2 pilas "AA" en el  
compartimiento de las pilas, en el  
sentido indicado por las marcas de polaridad (+/-).  
3) Vuelva a poner la cubierta.  
Asegúrese de desconectar la alimentación de todos  
los componentes del sistema antes de conectar otro  
componente.  
Consulte los manuales de instrucciones de los  
componentes que va a conectar al televisor/  
videograbadora/DVD.  
Si conecta un decodificador Dolby Digital, ajuste  
la función DOLBY DIGITAL a ON para salida de  
audio en el modo de configuración.  
A menos que se haga la conexión a un decodifi-  
cador Dolby Digital, ajuste la función Dolby  
Digital a OFF para salida de audio en el modo de  
configuración. La reproducción en un  
MODO DE ENTRADA EXTERNA  
Al usar una señal de entrada externa (otra videograbado-  
ra o una videocámara), conecte los cables de salida de  
audio/vídeo del equipo externo a las tomas AUDIO L/R  
IN/ VIDEO IN de su televisor/videograbadora/DVD.  
Luego, presione los botón CHANNEL K o L hasta que  
aparezca "AUX" en la pantalla.  
televisor/videograbadora/DVD utilizando ajustes  
incorrectos puede generar ruido y distorsión, y  
también puede causar daños a los altavoces.  
CONEXIÓN A UN AMPLIFICADOR  
ESTÉREO EQUIPADO CONTOMAS DE  
ENTRADA DIGITAL, PLATINA MD O  
PLATINA DAT (Para DVD)  
Fabricado bajo licencia de Dolby  
Laboratories. “Dolby” y el símbolo de la D  
doble son marcas de fábrica de Dolby  
Laboratories.  
Utilice un cable digital coaxial de audio de venta en el  
comercio especializado para hacer las conexiones de audio.  
Conexión a un amplificador equipado con tomas de  
entrada digital, platina MD o platina DAT.  
SECCIÓN DE TV/VCR  
PREPARACIÓN PARA LA  
UTILIZACIÓN  
Consulte la figura 6 de la página 13  
NOTAS:  
La fuente de audio de un disco grabado en formato de  
sonido envolvente Dolby Digital de 5,1 canales no se  
puede grabar como sonido digital mediante una plati-  
SELECCIÓN DE IDIOMA  
TV/VCR  
nAaseMgúDreoseDdAeTd. esconectar la alimentación de todos  
1
Enchufe el cordón de alimentación  
del televisor/videograbadora/DVD  
los componentes del sistema antes de conectar otro  
cCoomnspuolnteenlotes.manuales de instrucciones de los compo-  
nentes que va a conectar al televisor/videograbadora/  
televisor/videograbadora/DVD en una toma de CA  
Enchufe el cordón de alimentación del  
estándar.  
DAVjuDst.e la función Dolby Digital a OFF para salida de  
audio en el modo de configuración. La reproducción  
en un televisor/videograbadora/DVD utilizando  
ajustes incorrectos puede generar ruido y distorsión, y  
también puede causar daños a los altavoces.  
NOTA:  
Si aparecen algunas cifras en la esquina de la pan-  
talla, pulse el botón POWER sin desenchufar el  
cordón de alimentación.  
Asegúrese de que ...  
Pulse el botón POWER para encender el  
televisor/videograbadora/DVD.  
CONEXIÓN A UN DECODIFICADOR  
DOLBY DIGITAL (para DVD)  
NOTA: Esta función afecta sólo el idioma en el menú  
de la pantalla y no la fuente de audio.  
Si utiliza este televisor/videograbadora/DVD para  
reproducir un disco DVD grabado en formato de  
sonido envolvente Dolby Digital de 5,1 canales, el  
televisor/videograbadora/DVD emitirá un flujo de  
datos DOLBY DIGITAL desde su toma de salida de  
audio digital COAXIAL. Si conecta el reproductor a  
un decodificador Dolby Digital, podrá disfrutar de  
una tonalidad más convincente y real, con un sonido  
envolvente potente y de alta calidad similar al de los  
cines.  
2
Seleccione “LANGUAGE”  
Pulse el botón SETUP en el mando a distancia.  
Pulse el botón K o L para señalar “LANGUAGE”.  
3
Seleccione “ENGLISH”, “ESPAÑOL” o  
“FRANÇAIS”  
Seleccione “ENGLISH”, “ESPAÑOL” o “FRANÇAIS”  
con el botón ENTER.  
4
Salga del modo de idioma  
Pulse el botón SETUP en el mando a distancia para  
volver al modo del televisor.  
Utilice cables digitales coaxiales de audio  
disponibles en el comercio especializado para hacer  
las conexiones de audio.  
ES  
54  
0C28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NOTA: Si, por alguna razón, el menú está en inglés o  
francés, pulse el botón SETUP en el mando a distancia,  
pulse el botón K o L para señalar el “LANGUAGE  
[ENGLISH]” o “LANGAGE [FRANÇAIS]”, a contin-  
uación, pulse el botón ENTER y pulse el botón SETUP  
en el mando a distancia.  
1)Pulse el botón SETUP en el mando a distancia.  
Pulse el botón K o L para indicar “AJUSTE  
RELOJ”.  
Luego, pulse el botón ENTER.  
2)Pulse el botón K o L para indicar “AJUSTE  
MANUAL RELOJ”.  
Luego, pulse el botón ENTER.  
3)Pulse el botón K o L hasta que aparezca el mes  
deseado. (Ejemplo: Mayo - 05)  
AJUSTE DE CANAL  
TV/VCR  
Luego, pulse el botón B.  
Puede programar el sintonizador para buscar todos  
los canales que recibe en su localidad.  
4)Pulse el botón K o L hasta que aparezca el día  
del mes deseado. (Ejemplo: 6 - 06)  
Luego, pulse el botón B.  
5)Pulse el botón K o L hasta que aparezca el año  
deseado. (Ejemplo: 2004)  
Luego, pulse el botón B.  
6)Pulse el botón K o L hasta que aparezca la hora  
deseada. (Ejemplo: 5, PM)  
NOTA: El canal preparado NO es necesario cuando  
esté conectado a una caja de cable o caja de satélite.  
Sólo tiene que seleccionar con el selector de canal  
del televisor/videograbadora/DVD al canal de salida  
de la caja de cabe o caja de satélite (por ejemplo el  
canal CH3). Seleccione el canal a ver en la caja de  
cable o caja de satélite.  
Luego, pulse el botón B.  
Asegúrese de que ...  
7)Pulse el botón K o L hasta que aparezca el minu-  
to deseado. (Ejemplo: 40)  
Pulse el botón POWER para encender el televi-  
sor/videograbadora/DVD.  
8)Pulse el botón SETUP en el mando a distancia.  
Aunque los segundos no se visualizan, éstos  
empiezan a contar desde 00 cuando se pulsa  
SETUP en el mando a distancia. Utilice esta fun-  
ción para sincronizar el reloj con la hora correcta.  
1 Seleccione “AJUSTE DE CANAL”  
Pulse el botón SETUP en el mando a distancia.  
Pulse el botón K o L para señalar “AJUSTE DE  
CANAL”.  
A continuación, pulse el botón ENTER.  
2 Empiece el prefijado automático  
Pulse el botón K o L para señalar “AUTOPROGRA-  
MACION DE CA”.  
SECCIÓN DE DVD  
A continuación, pulse el botón ENTER.  
El sintonizador busca y memoriza todos los canales  
activos en su localidad.  
REPRODUCCIÓN BÁSICA  
DVD-V  
CD  
MP3  
3 Después de buscar  
El sintonizador se detiene en el canal memorizado  
más bajo.  
Para empezar  
¡Conecte la alimentación del amplificador y otros  
componentes, si es necesario.  
Cuando se activa AUTOPROGRAMACION DE  
CA, donde no hay entrada de señal del televisor,  
aparecerá “NO HAY SEÑAL DE TV” en la pan-  
talla después de terminar la búsqueda de canales.  
1
Presione el botón POWER.  
¡La alimentación se conectará.  
2
3
4
Presione el botón OPEN/CLOSE para abrir  
la bandeja de carga del disco.  
El televisor/videograbadora/DVD puede reconocer  
los canales de TV para que sean canales de TV de  
antena de cable con las condiciones de recepción.  
En este caso, pruebe nuevamente con el prefijado  
automático en las condiciones de recepción fina.  
Ponga el disco deseado en la bandeja, con  
la etiqueta hacia arriba.  
Presione el botón PLAY.  
¡La bandeja se cerrará automáticamente y la repro-  
ducción comenzará desde el primer capítulo o pista  
del disco. Si la reproducción no comienza automáti-  
camente, presione el botón PLAY.  
¡Cuando reproduzca un DVD que tenga grabado un  
menú de títulos, el menú podrá aparecer en la pan-  
talla.  
AJUSTE DEL RELOJ  
TV/VCR  
Cerciórese...  
La alimentación del televisor/videograbadora/DVD  
deberá estar conectada.  
En el ejemplo de abajo, el reloj va a ajustarse así:  
FECHA: 6 de mayo de 2004  
HORA: 5:40 PM  
5
Presione el botón STOP para detener la  
reproducción.  
ES  
55  
0C28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
LIMITED WARRANTY  
FUNAI CORP. will repair this SYLVANIA product, free of charge in the USA in the event of defect in materials or  
workmanship as follows:  
DURATION:  
PARTS:  
FUNAI CORP. will provide parts to replace defective parts without charge for one (1) year from the  
date of original retail purchase. Two (2) years for Picture Tube. Certain parts are excluded from this  
warranty.  
LABOR: FUNAI CORP. will provide the labor without charge for a period of ninety (90) days from the date of  
original retail purchase.  
LIMITS AND EXCLUSIONS:  
THIS WARRANTY IS EXTENDED ONLY TO THE ORIGINAL RETAIL PURCHASER. A PURCHASE  
RECEIPT OR OTHER PROOF OF ORIGINAL RETAIL PURCHASE WILL BE REQUIRED TOGETHER WITH  
THE PRODUCT TO OBTAIN SERVICE UNDER THIS WARRANTY.  
This warranty shall not be extended to any other person or transferee.  
This warranty is void and of no effect if any serial numbers on the product are altered, replaced, defaced, missing  
or if service was attempted by an unauthorized service center. This SYLVANIA Limited warranty does not apply to  
any product not purchased and used in the United States.  
This warranty only covers failures due to defects in material or workmanship which occurs during normal use. It  
does not cover damage which occurs in shipment, or failures which are caused by repairs, alterations or product not  
supplied by FUNAI CORP., or damage which results from accident, misuse, abuse, mishandling, misapplication,  
alteration, faulty installation, improper maintenance, commercial use such as hotel, rental or office use of this  
product or damage which results from fire, flood, lightning or other acts of God.  
THIS WARRANTY DOES NOT COVER PACKING MATERIALS, ANY ACCESSORIES (EXCEPT REMOTE  
CONTROL), ANY COSMETIC PARTS, COMPLETE ASSEMBLY PARTS, DEMO OR FLOOR MODELS.  
FUNAI CORP. AND ITS REPRESENTATIVES OR AGENTS SHALL IN NO EVENT BE LIABLE FOR ANY  
GENERAL, INDIRECT OR CONSEQUENTIAL DAMAGES ARISING OUT OF OR OCCASIONED BY THE  
USE OF OR THE INABILITY TO USE THIS PRODUCT. THIS WARRANTY IS MADE IN LIEU OF ALL  
OTHER WARRANTIES, EXPRESS OR IMPLIED, AND OF ALL OTHER LIABILITIES ON THE PART OF  
FUNAI, ALL OTHER WARRANTIES INCLUDING THE WARRANTY OF MERCHANTABILITY, AND  
FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED BY FUNAI AND ITS  
REPRESENTATIVES IN THE UNITED STATES.  
ALL WARRANTY INSPECTIONS AND REPAIRS MUST BE PERFORMED BY A FUNAI AUTHORIZED  
SERVICE CENTER. THIS WARRANTY IS VALID WHEN THE UNIT IS CARRIED-IN TO FUNAI  
AUTHORIZED SERVICE FACILITY.  
IMPORTANT:  
THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, YOU MAY HAVE OTHER RIGHTS  
THAT VARY FROM STATE TO STATE, IF, AT ANY TIME DURING THE WARRANTY PERIOD, YOU ARE  
UNABLE TO OBTAIN SATISFACTION WITH THE REPAIR OF THIS PRODUCT, PLEASE CONTACT FUNAI  
CORP.  
ATTENTION:  
FUNAI CORP. RESERVES THE RIGHT TO MODIFY ANY DESIGN OF THIS PRODUCT  
WITHOUT PRIOR NOTICE.  
To locate your nearest SYLVANIA Authorized Service Center or for general service procedure,  
please call 1-800-968-3429 or write to the following:  
FUNAI CORPORATION, INC.  
SERVICE CENTER  
19900 Van Ness Avenue, Torrance, CA 90501  
Tel :1-800-968-3429  
Head Office: 100 North Street, Teterboro, NJ 07608  
PLEASE DO NOT SHIP YOUR UNIT TO THE TETERBORO ADDRESS.  
Printed in Malaysia  
0EMN02539  
T6001UB ★★★★★  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Sharp Projection Television XG NV2SB User Manual
Shoprider Mobility Aid UL7WR 10 User Manual
Solo USA Trimmer 129HS User Manual
Sony Microphone ECM MS957 User Manual
Sony Security Camera SNC CS50N User Manual
Sony Stereo Receiver 3 289 204 411 User Manual
Sony VCR SLV 669HF User Manual
Star Manufacturing Convection Oven CCOQ 3 User Manual
Sterling Plumbing Indoor Furnishings 402025 User Manual
Suzuki Thermometer 86W41 User Manual