swisherinc.com
OWNER’S
MANUAL
MODEL NO.
LS722X
STARTING SERIAL #:
L206-010001
LOG
SPLITTER
Safety
IMPORTANT
Assembly
Read and follow all Safety
Precautions and Instructions
before operating this
equipment.
Operation
Service and Adjustment
Repair Parts
Rev. 06-010
1602 CORPORATE DRIVE, WARRENSBURG, MISSOURI 64093 PHONE 660-747-8183
FAX 660-747-8650
Made In The
USA
Manufacturing quality lawn care equipment since 1945
11624
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY PRECAUTIONS
This Safety Alert Symbol indicates important messages in this manual.
When you see this symbol, carefully read the message that follows and be
alert to the possibility of personal injury.
Read this manual completely. This machine can amputate hands, feet, and throw objects.
Failure to observe the following safety instructions could result in serious injury or death.
WARNING: The engine exhaust from this product contains chemicals known to the state of California
to cause cancer, birth defects or other reproductive harm.
DANGER: Your log splitter was built to be operated according to the rules for safe operation in this
manual. As with any type of power equipment, carelessness or error on the part of the operator can result
in serious injury. If you violate any of these rules, you may cause serious injury to yourself or others.
•
•
Read and understand the manual. Learn to operate this equipment in a safe manner. Familiarize
yourself with all of the controls in a safe environment before starting to work with this machine.
DO NOT under any circumstances alter this log splitter. This equipment was designed and
engineered in accordance with operating instructions. Altering this equipment, or using this
equipment in such a way as to circumvent its design capabilities and capacities, could result in
serious injury or fatality and WILL VOID THE WARRANTY.
•
•
•
•
Allow ONLY responsible adults who have read this manual to operate this machine. NEVER
allow children to operate this machine.
NEVER operate or allow someone to operate this equipment while under the influence of
alcohol, drugs or medication. Being coherent is essential for safety.
ALWAYS use outdoors with adequate ventilation. DON’T run the engine in an enclosed area.
Exhaust gases contain carbon monoxide. This odorless gas can be deadly when inhaled.
NEVER use splitter for any other purpose than splitting wood. Any other use can result in
injury. Your splitter is a precision piece of power equipment, not a toy. Therefore, exercise
extreme caution at all times.
•
ONLY a single operator is to load and operate the log splitter. KEEP all others, including pets
and children, a minimum of 20 feet away from your work area. More accidents occur when
more than one person operates the log splitter than any other time.
•
•
•
•
ALWAYS wear protective gear such as safety goggles, protective hearing device, steel-toed
shoes, and tight-fitting gloves without drawstrings or loose cuffs.
NEVER wear loose clothing or jewelry that can be caught by moving parts of the splitter and
pull you into it. Keep hair away from moving parts.
NEVER operate your splitter on wet, muddy, or icy surfaces. KEEP work area clean of split
wood. Safe footing is essential in preventing accidents.
ONLY operate splitter on level ground with wheels blocked, not on the side of a hill. It could
tip, or rolling logs, poor footing, etc. could cause an accident.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
•
NEVER operate your splitter near a flame or spark. Hydraulic oil and gasoline are flammable and can
explode.
•
•
NEVER fill gas tank while the engine is hot or running. Allow the engine to cool before refueling.
This unit is equipped with an internal combustion engine and should not be used on or near any
unimproved forest-covered, brush-covered or grass-covered land unless the engine’s exhaust system is
equipped with a spark arrester meeting applicable local or state laws (if any). If a spark arrester is used it
should be maintained in effective working order by the operator.
-NOTE-
In the state of California, the above is required by law (Section 442 of the California Public Resources Code).
Other states may have similar laws. Federal laws apply on federal lands. A spark arrester muffler (optional by
manufacturer) is available at your nearest engine dealer. Check legal requirements in your area.
•
•
•
ONLY use your hands to operate the control lever. NEVER use foot, knee, rope or any extension device.
Split ONLY one log at a time. NEVER attempt to split two logs on top of each other.
NEVER place hands or feet between log and splitting wedge or between log and ram during forward or
reverse stroke. ALWAYS keep fingers clear of splits that open in log during splitting operation.
•
•
DO NOT straddle or reach across the splitting area while operating the splitter.
DO NOT step over splitter when the engine is running. You may trip or accidentally activate the splitting
wedge. Walk around to get to the other side.
•
•
•
•
NEVER attempt to load splitter while splitting wedge is in motion. When loading log splitter, place hands
on the sides of the log, not the ends.
NEVER attempt to split woods across the grain. Wood may burst or fly out of your splitter and result in
serious injury.
NEVER leave your splitter unattended with the engine running. Shut off the engine if you are leaving
your splitter, even for a short period of time. Someone could accidentally activate the ram and be injured.
Both ends of the log should be cut as squarely as possible to prevent the log from sliding out of the splitter
during operation. Log length should be kept to 24” or less.
•
•
NEVER operate your splitter while it is attached to the tow vehicle.
BEFORE towing, be certain that the splitter is securely attached to the towing vehicle and that the support
leg, beam and cylinder are secured in there respective towing positions.
•
•
•
NEVER allow persons to ride on splitter. DO NOT carry any cargo or wood on your splitter. It may fall
off and cause an accident.
DO NOT loosen or remove any hydraulic fitting, line or reservoir cap while your splitter or engine is
running.
Fluid escaping from a very small hole can almost be invisible. DO NOT check for leaks with your hand.
See maintenance section for instructions. IF injured by escaping fluid, see a doctor at once. Serious
infection or reaction can develop if proper medical treatment is not administered immediately.
•
•
DO NOT operate your splitter in poor mechanical condition or when it is need of repair.
ALWAYS disconnect the spark plug wire and place the wire where it cannot contact the spark plug, to
prevent accidental starting the engine when setting up, transporting, adjusting or repairing.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
This log splitter has been partially assembled at the factory. Refer to the drawings and part lists should it become
necessary to disassemble the unit for repair or replacement of parts.
Inspect all components for damage. If you believe you have a damaged part please contact customer service
immediately at 1-800-222-8183.
Exercise extreme caution, as parts are very heavy. Sufficient persons or mechanical handling
WARNING:
equipment should be used.
Refer to uncrating and assembly instructions for assembly procedures.
OPERATION
This log splitter is intended and designed to only split wood. NEVER use for any other
INTENDED USE:
purposes. Doing so can cause injury or VOID THE WARRANTY.
IMPORTANT: This unit is shipped with oil but without gasoline in the engine. After assembly, see separate
Engine Manual for proper fuel and oil recommendations.
WARNING: DO NOT START OR RUN THE LOG SPLITTER WITHOUT OIL IN THE ENGINE
AND HYDRAULIC RESERVOIR.
FILLING THE HYDRAULIC RESERVOIR
Fill the hydraulic reservoir with at least 12 Quarts of Dextron III Automatic Transmission fluid or 10W AW
hydraulic fluid. After the hydraulic reservoir and the engine crankcase are filled correctly with their respective
oils, start the engine. Remember to set the throttle and turn on the fuel shut-off valve. The hydraulic pump
should prime itself. With the engine running, move the hydraulic valve lever toward the wedge. This will cause
the cylinder to extend and expel air. When the cylinder is fully extended, retract it. Repeat this procedure several
times. (An erratic movement of the cylinder indicates that there is air in the system). Once the cylinder has a
smooth and constant speed indicating that all air has been expelled, add another 4 quarts of oil, this should then
bring the fluid level up to approximately 3” below the fill hole. This model requires approx. 16-17 Quarts of
hydraulic fluid.
NOTE: If the tank is overfilled, it will tend to expel oil from the breather cap when the cylinder is retracted.
START UP
WARNING: DO NOT START OR RUN THE LOG SPLITTER WITHOUT OIL IN THE ENGINE
AND HYDRAULIC RESERVOIR.
See separate Engine Manual for fuel and oil recommendations. If applicable your log splitter has come equipped
with a fuel shut-off valve for towing purposes.
Before starting engine make sure crankcase is filled correctly with oil and the proper fuel has been used. The
engine will only start when the throttle lever and fuel shut-off valve if applicable are turned to their ON positions.
STARTING INSTRUCTIONS
Briggs & Stratton 7HP Engine
1. Move throttle control to “FAST.”
2. Push primer bulb three (3) times. NOTE: Do not use primer to restart a warm engine after a short
shutdown.
3. Grasp rope handle and pull out slowly until resistance it felt. Then pull rapidly with a full arm stroke.
NOTE: If engine fails to start after three (3) pulls, repeat steps 1 and 2.
4. When Engine starts, leave throttle control at “FAST.” The throttle must be set in the fast position for
maximum performance.
5. To stop engine, move throttle lever to “SLOW” for a few seconds then to “STOP.”
5
Download from Www.Somanuals.com. All Manuals Search And Download.
POSITIONING THE CYLINDER
1. Remove lock pins from the cylinder retention clips and rotate clips down exposing the open slots on the
cylinder retention bracket (reference Figure 2).
2. Slide the Cylinder forward until the rear trunnions clear the slots then lift the back side of the cylinder until
the rear trunnions clear the cylinder retention bracket and slide cylinder back until the front cylinder
trunnions slide into the open slots of the cylinder retention bracket (reference arrow in Figure 2).
3. Rotate the cylinder retention clips upward around the cylinder trunnions and lock them in place using the
lock pins.
4. Next you need to remove the lock pin from the beam pivot bracket and rotate the beam counter clockwise
90 degrees until the pivot holes are in alignment and reinstall ball lock pin (reference Figure 4). Your
splitter is now in the horizontal operating position.
5. Remove the hitch pin from the beam pivot (reference Figure 4). Pivot your beam into the vertical position
and reinstall the hitch pin in the center hole (reference Figure 5). Your splitter is now in the vertical
operating position.
Figure 1
Figure 2
Figure 3
Figure 4
Figure 5
6
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING: NEVER OPERATE THE SPLITTER WITH THE CYLINDER IN THE STORED
POSITION.
SPLITTER OPERATION
1. Set up the log splitter in a clear, level area and block the wheels. The suction port on the tank should
always be on the lower side of the log splitter.
2. Place a log on the beam, against the foot plate. Make sure the log is securely on the foot plate and up
against the beam.
3. Depress the valve lever so that the cylinder will drive the push block into the log. Extend the cylinder
until the log splits or to the end of its stroke. If the log has not completely split after the cylinder has
reached the end of its extension, retract the cylinder. NOTE: Leaving the valve in the “actuate” position
at the end of the stroke may damage the pump. Always use extra care when splitting logs with ends that
are not square.
NOTE: To extend the life of the hydraulic cylinder, avoid “BOTTOMING OUT” the cylinder.
TOWING SAFETY
This unit should not be towed on any street, highway, or public road without checking the existing federal, local,
and state laws. Any licensing or modifications such as taillights, etc., need to comply with existing federal, local,
or state vehicle requirements is the sole responsibility of the purchaser. Obey all regulations when towing on
public roads and highways. See also SAFETY PERCAUTIONS.
WARNING: NEVER TOW THE SPLITTER WITH CYLINDER IN THE OPERATING POSITION.
Turn the fuel shut-off valve if applicable OFF to prevent flooding of the engine while traveling.
Be careful when backing up. You can easily jack-knife your splitter.
TOWING AT NIGHT
The requirements for taillights are based on States regulations. Some states allow towing at night as
long as the towed equipment does not visibly impair the tow vehicle taillights. This is based on a state,
to state requirements. The customer is responsible for meeting the states requirements.
If a “Statement of Origin” is required in your state, see your local dealer to receive one.
HYDRAULIC SAFETY
The hydraulic system on your splitter requires careful inspection along with the mechanical parts. Be sure to
replace any frayed, kinked, cracked or otherwise damaged hydraulic components. Just because it isn’t leaking
today doesn’t mean that it will not fail tomorrow.
Fluid escaping from a very small hole can almost be invisible. Do not check for leaks with your hand. Escaping
fluid under pressure can have sufficient force to penetrate skin causing serious personal injury or even death.
Leaks can be detected by passing a piece of cardboard or wood over the suspected leak and looking for
discoloration. IF injured by escaping fluid, see a doctor at once. Serious infection or reaction can develop if
proper medical treatment is not administered immediately.
Should it become necessary to loosen or remove any hydraulic fittings, lines or reservoir cap, be sure to relieve all
pressure by shutting of the engine and moving the control handle back and forth several times.
NEVER remove the cap from the hydraulic tank or reservoir while the unit is running. Hot oil under pressure
could result in serious injury. See also SAFETY PERCAUTIONS.
The pressure relief valve on your splitter is preset at the factory. DO NOT adjust the valve. Only a qualified
technician should perform this adjustment.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE AND STORAGE
WARNING: DISCONNECT THE SPARK PLUG BEFORE PERFORMING ANY MAINTENANCE.
Consult the operating and maintenance instructions of the engine manufacturer for engine care.
Always check the oil level of the hydraulic reservoir before operation. Operating without an adequate oil
supply will cause severe damage to the pump.
Periodically check that all nuts, bolts, screws, clamps and fittings are tight and secure.
To keep your splitter in top working condition perform all recommended maintenance procedures before you use
your splitter.
If the wedge becomes dull or nicked a grinder or sharpening tool can be used to sharpen it.
Completely drain the fuel tank prior to storage. Always store gasoline in an approved, tightly sealed container. Store
container in a dry, cool place with adequate ventilation. Keep fuel away from areas where fumes could contact open
flame, pilot light or sparks.
Be aware of the environment when disposing of used petroleum products. Please dispose of used hydraulic
fluid, engine oil and any by products from the maintenance of your splitter at approved recycling centers.
Should it become necessary to disassemble the unit for repair or replacement of parts, refer to the drawings and parts
list on the following pages. Exercise extreme caution, as some parts are very heavy and will require sufficient
persons or mechanical handling equipment.
Your Swisher Log Splitter has been produced with components designed specifically to this machine. Although
standard springs, hardware and ect may look similar to parts used on other machinery, they may in some cases
be made of a different construction and/or materials. All replacement parts must meet manufacturer’s
specifications.
The operation of any splitter can produce foreign objects to be thrown into the
eyes, resulting in severe eye damage. Always wear certified safety glasses or
wide-vision safety goggles over spectacles before staring any splitting machine
and while operating such a machine.
The operation of any splitter produces sound waves that are damaging to the
human ear. Ear protection is recommended.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY DECALS
Replace decals immediately if damaged.
OD16 – FUEL SHUT OFF DECAL
OD07 – COLD WEATHER DECAL
(NOT ALL MODELS)
OD12 – HYDRAULIC FILL PLUG
DECAL
11794 – CAUTION DECAL
OD33– SPEED DECAL
11427 – LS DANGER DECAL
9
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY DETAIL
LS722X MODELS
10
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICE PARTS
Please have Model and Serial Numbers ready when ordering parts.
Color cannot be guaranteed upon service parts.
ITEM NUMBER
DESCRIPTION
54" Return Hose
PART NUMBER
1
2
7290
7289
48" Pressure Hose
#12 Hose Clamp
3
LS5001
7329
4
Return Line Fitting
5
Filter Head
LS1112
LS1113
7379
6
Filter Element
7
3/4" NPT Filler Cap w/Hole
Hydraulic Reservoir/Tank
Bolt 3/8-16 X 3/4 Serr Flange
Nut 3/8-16 Serr Flange
Bolt 5/16-18 X 3/4 Serr Flange
Nut 5/16-18 Serr Flange
#16 Hose Clamp
8
11467TK
NB780
NB779
NB596
NB170
LS4999
7346
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24A
24B
25
26
27
28
29
30
30A
30B
30C
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
20" Suction Hose
Hydraulic Pump-LS722X
Pressure Line Fitting
Motor Base Weldment
Tongue Support Weldment
3/8 X 2 1/2 Safety Hitch Pin
Bolt 3/8-16 X 2 1/2 GR 5
Washer 3/8 SAE
LS2001H
11248
11207TK
11373TK
H11
NB619
NB272
NB182
11374TK
11372TK
11425TK
11371TK
NB743
11615TK
NB275
NB181
11619
Nut 3/8-16 Nyloc
Tongue Weldment
Leg Support Bracket 1
Leg Support Bracket 2
Leg Weldment
5/16-18 Special Hex Flange Shoulder Bolt
Additional Support Weldment
Washer 5/16 SAE
Nut 5/16-18 Nyloc
5/16 X 1 Ball Lok Pin - Ring Grip
Plastic Lanyard
NB652
NB114
NB524
NB107
024002
7306
Bolt 1/4-20 X 1/2 MSC ZP
Nut 1/4-20 Serrated Flange
Bolt 3/8-16 X 1 1/2 GR 5
1/8 X 1/2 #3 Woodruff Key
Pump Pulley
5/16-18 X 1/2 Set Screw w/Loctite
37" Belt
NB312
11399
Idler Bushing
6037
Idler Arm
6041TK
6040
Idler Spacer
Idler Pulley
B527
Nut 3/8-16 2-Way Lock
Clutch Lever
NB280
11226TK
2077
Handle Grip
Clutch Spring
682S
Bolt 3/8-16 X 5 Turned Eye
Tension Strap
11223
11376TK
11370TK
F4157WF
NB184
NB126
Axle Weldment
Tire & Wheel
Washer 3/4ID X 1 1/4OD 10GA
Cotter Pin 1/8" X 1"
11
Download from Www.Somanuals.com. All Manuals Search And Download.
BEAM DETAIL
ITEM NUMBER
DESCRIPTION
Beam Weldment
PART NUMBER
11468TK
11910TK
11857TK
10501
1
2
Wedge Weldment
Wedge GIB Angle
Bolt 3/8-16 X 1 1/4 Carriage
Nut 3/8-16 Nyloc
3
4
5
NB182
NB121
NB577
11242TK
7292
6
Nut 1/2-13 Nyloc Jam
1/2-13 X 3 1/2 GR5 ZP
Ram Cylinder
7
8
9
2-Way Pipe Nipple
Hydraulic Fitting
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
7291
Stationary Line Assembly
Valve Inlet Fitting
7288TK
7387
Valve Control
7287TK
7329
Return Line Fitting
Master Chain Link
Valve Control Handle
Handle Grip
7424
7423
7425
1/4 X 1 Clevis Pin
NB522
NB597
11393TK
NB632
NB504
NB275
7839Z
Cotter Pin
Cylinder Retention Plate
3/8" X 1 3/8" Hitch Pin
Bolt 5/16-18 X 1 1/4 HCC GR5
Washer 5/16" SAE
Latch Pin Bushing
Washer 17/32 X 1 1/4 X 16GA
Nut 5/16-18 Nyloc Nut
NB217
NB181
12
Download from Www.Somanuals.com. All Manuals Search And Download.
PIVOT DETAIL
Hydraulic Hoses Not Shown for Clarity
ITEM #
DESCRIPTION
PART #
11469TK
11431
1
2
Beam Pivot Weldment
Bolt 3/4-10 X 2 GR8
3
Washer Belleville 1.50 OD X .761 ID X .098 X .134
Washer 3/4 SAE
AS155
NB146
NB609
NB132
NB281
NB648
11397
4
5
Nut 3/4-10 Nyloc
6
Bolt 1/2-13 X 4 GR5
7
Nut 1/2-13 Nyloc
8
1/2 X 3 1/2 HITCH PIN W/ HAIR PIN
3/8 X 1 5/8 Ball Lok Pin
9
10
11
Plastic Lanyard
NB652
NB690
1/4-20 X 3/4 Serrated Flange Bolt GR5
1
2
3
4
ENGINE DETAIL
5
6
4
ITEM #
DESCRIPTION
Engine
PART #
N/A
1
2
Bolt 5/16-18 X 2 1/4 Serr. Flange
Bolt 5/16-18 X 1 1/4 Serr. Flange
Nut 5/16-18 Serr. Flange
3/16 X 1 Keystock
NB622
NB253
NB170
9030
8
7
3
4
5
9
6
5/16-18 X 1/2 Set Screw w/Loctite
Engine Pulley 7/8" ID
NB312
7323
7
8
Washer Belleville
699
9
Bolt 3/8-24 X 1 w/Loctite
Fuel Shut Off Valve (Inline)
Fuel Line Clamp
NB238N
7414
NOTSHOWN
NOTSHOWN
6FLC
13
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
:
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
14
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
Models
LS722X
Splitting
22 Tons
Force
7 HP Briggs and
Stratton Intek
Engine
Splitting
Positions
Cylinder
Size
Horizontal/Vertical
4" X 24"
2 Stage with Heavy
Duty Bearings
Pump
11 Gallons Per
Minute
Pump
Specs
Valve
Auto Return
Belt Drive with
Clutch for Easy
Starting
Drive
System
Hydraulic
Fluid
16-17 Quarts
Capacity
Maximum
Log length
Tire Specs
Metal
25"
13.00 X 5.00
No
Fenders
No
Ball Hitch
Unit
410 Lbs
Weight
15
Download from Www.Somanuals.com. All Manuals Search And Download.
LOG SPLITTER
OWNER’S
MANUAL
HOW TO ORDER
REPAIR PARTS:
Each Log Splitter has its own serial number. Each engine has
its own serial number. The serial number for the Log Splitter
will be found on the right hand side of the hydraulic oil
reservoir. The serial number for the engine will be found on
the top of the blower fan housing.
All Log Splitter parts listed herein may be ordered directly
from Swisher Mower & Machine Co. Inc., your nearest
Swisher dealer, or from our website.
MODEL NO.
LS722X
All engine parts may be ordered from the nearest dealer of the
engine supplied with your log splitter. Parts subject to change
without notice.
WHEN ORDERING PARTS, PLEASE HAVE THE
FOLLOWING INFORMATION AVAILABLE:
* PRODUCT – SWISHER LOG SPLITTER
* SERIAL NUMBER - _______________
* MODEL NUMBER - _______________
* ENGINE MODEL NUMBER - _______________
TYPE - _______________
* PART NUMBER
* PART DESCRIPTION
TELEPHONE - 1-800-222-8183
FAX - 1-660-747-8650
SWISHER MOWER & MACHINE CO. INC.
1602 CORPORATE DRIVE
WARRENSBURG, MO 64093
SWISHER MOWER & MACHINE CO. INC.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
|