Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Important Safety Instructions......................ꢀ
Introduction.................................................4
Features......................................................7
System Design, Installation and
Connections..............................................10
Connectors/Pinout .................................1ꢀ
System Connections..............................16
Programming ............................................18
Feature Enable/Disable ............................19
Specifications............................................ꢀ0
Troubleshooting........................................ꢀ1
Warranty ...................................................ꢀ3
Service Assistance....................................ꢀ3
For more information on this and other Sunfire
products, please visit our website:
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
The Olé®-ꢀSF Film Interactive
Touchpad (FIT) is a revolutionary
in-wall controller for your Sunfire
receiver or processor. Using a
photographic film overlay instead of
hard buttons, it marries the beauty
of a touchscreen with the simplicity
of a keypad –seamlessly controlling
all major functions of your home
theater or secondary room.
Unpacking
Your Olé-ꢀSF touchpad should
reach you in perfect condition. If
you do notice any shipping damage,
please contact Sunfire immediately.
Gently lift out the touchpad and all
the packing material. It is important
to save all the packing materials and
the box in case your touchpad ever
needs to be moved or shipped for
repair.
The backlit film transparency
provides system control icons and
functions, while a 4-line ꢀ" color
OLED displays multiple pages of
source control and feedback to the
user. Multiple IR commands, or
‘Sequences’, can be issued from a
single press of any button. Program-
ming is accomplished with Sunfire’s
SunTools™ setup software, and is
done through a direct link from a
computer to the mini-USB download
port on the front of the Olé-ꢀSF.
Make sure that you keep your
sales receipt. It is the only way
to establish the duration of your
Limited Warranty and it may come in
useful for insurance purposes.
Each button location (or “hot
spot”) is assigned a command
that controls sources such as
A/V equipment, HVAC systems,
drapes, shades, lighting systems,
or even fireplaces! Your Olé-2SF is
configured out of the box to control
your Olé-ready Sunfire receiver or
processor’s Zone ꢀ output. Custom-
programming by your authorized
Sunfire dealer will allow reconfigur-
ing of the Olé-ꢀSF to control the
main theater system and a variety of
functions required for your specific
system.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Features
Care
•
Plug-and-play. Right out of the
If your Olé-ꢀSF touchpad needs
box, the Olé-ꢀSF controls Zone
2 on Olé-ready Sunfire receivers
and processors
servicing, please read the Trouble-
shooting section on page ꢀ1. If a
problem persists, please contact
your nearest authorized Sunfire
Dealer.
•
•
•
•
•
Simple SunTools™ PC program-
ming for customization
Sunfire Optimized™ graphics and
programming
Please take a moment to fill out
and mail the Sunfire Customer Re-
sponse card. Also record the serial
number and your details here:
Full touchpad design, with no hard
buttons
Two inch color OLED (Organic
LED)
Serial Number:
Two-way feedback for artist/song
data from SIRIUS satellite radio
and VIA!migo™ iPod® cradle
Purchased from:
•
•
Automatic brightness-adjusting via
light sensor
Audible ‘click’ to indicate a button
press (can be disabled in soft-
ware)
Date:
•
•
•
Built-in IR receiver for passing IR
commands back to the main room
Connectivity for Local IR Output
and Remote IR Receiver
Virtually unlimited IR command
sequences issued from any button
press
•
•
•
•
System sense sequence capabil-
ity
Fits in a double-gang electrical
box
Stylish Euro wall plate in optional
colors
Patent pending design
ꢁ
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation & Usage Tips
•
When properly installed, nothing
should be applying contact pres-
sure to the touchpad except for
the operator’s finger. If something
is touching the touchscreen
window, a false signal can be
generated causing the touchpad
not to respond to a finger press
(Sunfire does not recommend
wrapping the removable frame
with wallpaper as this can cause
the aforementioned symptom).
Too much force on the front of the
touchpad, or concentrated pres-
sure, can damage the polyester
film or break the underlying glass
plate.
•
•
Avoid applying any foreign ob-
jects, such as adhesive labels, on
the touchscreens polyester film.
This can release chemicals that
can discolor the clear film.
The touchpad should not be
mounted near electronics that
emit radio frequencies or elec-
tromagnetic interference (such
as the deflection circuits of CRT
monitors, light dimmers, and some
power supplies)
•
The edge of the touchpad has
exposed sharp glass. Be careful
when handling the assembly in
order to avoid injury.
•
•
•
Avoid installation in direct sunlight
or strong ultraviolet light (such
as grow lamps, plant lights, or
compact fluorescent lights). This
can degrade and discolor the
polyester film.
Cleaning the touch screen
To clean the polyester film, first
use a soft dry cloth to remove
contamination. If dust or smudges
are still present, disconnect the
touchpad, and use a damp cloth
that has been squeezed of excess
water to remove the contaminant. If
contaminants are still present, use
a non-abrasive cleaner or detergent
to clean the polyester film. Use
of strong chemicals and/or some
cleaning agents may discolor the
polyester film. The following cleans-
ers have been tested and approved
for cleaning an Olé-ꢀSF touchpad:
Avoid installation over heat
generating devices and/or in moist
areas where condensation can
form on the polyester film. Both
heat and condensed moisture can
affect touch screen performance.
Avoid installation next to thermo-
stats. The touch screen generates
heat that can affect thermostat
control and readings.
• Windex® Glass Cleaner
• Formula 409® Cleaner
• Mr. Clean®
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Features
Top Panel
1
1
4
3
ꢀ
3a
1
1
ꢁ
1. Mounting Screw (x 4) 4. Download Port
Use these screws to mount the
touchpad into a standard 3ꢀ cu in.
double-gang electrical box.
This mini USB download port is
used to program the touchpad, by
connecting it to the USB port of
a PC, using a standard USB-A to
USB-mini-B cable.
ꢀ. Program Button
This button is for future use.
ꢁ. Wall plate
3. Light Sensor
This stylish wall plate clips over
the top panel once the touchpad
has been installed into a double-
gang electrical box. It can be
easily removed to access the
download port.
When this sensor is enabled, the
Olé-ꢀSF backlight will brighten
or dim depending on the room's
ambient light conditions. Do not
cover the small hole (3a) in the
wall plate.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Touchpad display
9
8
10
11
7
1ꢀ
1ꢀ
6
ꢁ
13
ꢁ. Power
10.Volume up/down
Turns system audio on and off.
Adjust the volume in your system.
6. System
11. Mute
Bass/Treble control and other
Mute the sound in your system.
system options.
1ꢀ.Page up/down
7. Home
Page through different sources, or
This toggles between the main
source selection screen and the
current source control.
control pages within a source.
13.Navigation buttons
Controls various functions on
source components depending on
programming.
8. Source selection
View/change the source selection
pages.
9. Display
This display is used for source
selection and system information
such as the artist/song data from
SIRIUS satellite radio and the
VIA!migo™ iPod® dock.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Rear Panel
14
1ꢁ
16
14.Z•NET/VIA!NET
Switch
You must set this switch to
VIA!NET for use with Sunfire
receivers and processors.
1ꢁ.System RJ-4ꢁ Jack
Connect this jack with Cat-ꢁ cable
to the TP1 or TPꢀ RJ-4ꢁ con-
nectors on the rear panel of your
Sunfire receiver or processor.
16.Local IR Port
This port allows the connection of
local IR emitters and IR receivers,
local contact switches etc. See
pages 13–1ꢁ for connections.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
System Design, Installation and
Connections
Planning
Installation
Before installing the Olé-ꢀSF, it is
The Olé-2SF is designed to fit into
essential to have a detailed and ac-
curate system design. An authorized
Sunfire installer should be con-
tracted for proper installation and
programming of your touchpad. The
first step to a good design is to map
the system. It is advisable to mark
up a copy of the house floor plan
with speaker, keypad, touch panel,
volume control, and equipment
locations etc. Make sure that all
locations are decided upon before
pre-wiring commences, so that all
necessary wiring and installation
hardware is in place.
a standard 3ꢀ cu. in. double-gang
electrical box. Consult local building
codes for specifics in your geo-
graphic area. Note that the Olé-ꢀSF
is not designed for outdoor use.
Pre-Wire
The Olé-ꢀSF requires power,
control, and status to function cor-
rectly. Each touchpad has an RJ-4ꢁ
jack on the back to allow for easy
connection. Run Cat-ꢁ wire from the
receiver/processor location (head-
end) to the location where each
touchpad will be installed.
It is essential that ALL system
components are accounted for prior
to the pre-wire stage. After estab-
lishing design goals, make a de-
tailed list of all components. Include
source equipment, keypads, touch
panels, volume controls, amplifiers,
communications gear, etc. Gather
up any IR remote controls that may
be necessary for final programming,
or ensure that the IR codes for all
equipment to be installed are avail-
able in the SunTools IR Library.
Note: Use of wire other than Cat-ꢁ
may produce undesired results (IR
bandwidth may be narrowed or
interference may occur).
Warning: Never connect
the Olé-ꢀSF Cat-ꢁ cable to
computer Ethernet or LAN
systems, DSL routers etc.
Make sure that Cat-ꢁ cable
used with the Olé-ꢀSF is clearly
marked to avoid any confusion.
Note: Maximum wire run is ꢁ00
feet.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Rough-In
Roughing-in the Olé-ꢀSF requires
careful attention to the design plan
made previously. Review the previ-
ous page and make a list of things
to factor in to specific mounting loca-
tions, before deciding exactly where
to place the unit. In order to avoid
Electro-Magnetic Interference (EMI),
do not mount touchpads close to
light dimmers. Leave at least one
stud-bay open between touchpads
and dimmers (leave more space if
multiple dimmers are present). Avoid
installing Olé-ꢀSF touchpads in ar-
eas that will receive direct sunlight.
Sunlight can flood the IR receiver
and make the system inoperative.
Do not mount touchpads outdoors!
Corrosion will damage them. Sunfire
does not warrant Olé touchpads for
outdoor use.
Mounting Height
The Olé-ꢀSF has no viewing
angle limitations, so mounting
height should be determined by the
average height of the user. Typical
mounting height is ꢁ6-60 inches
from the floor to the bottom of the
frame. This will provide optimum
viewing for the largest number of
people.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Connectors/Pinout
RJ-4ꢁ Connector
The Olé-ꢀSF has a system RJ-4ꢁ
connector and a five-pin Interface
Port connector which each perform
specific functions. All applications
use the RJ-4ꢁ connector, while
certain situations will require the use
of the Local interface port.
Use Cat-ꢁ cable to connect the
Olé-2SF to a Sunfire receiver or pro-
cessor. The Sunfire standard pinout
configuration is shown below.
Sunfire TGR-401 Theater Grand Receiver
1ꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
Local IR Interface Port
IR-Emitter Out
Use this connector when utilizing
the Olé-ꢀSF’s local control features,
such as local source control, local
IR sensors, or sense-enabled auto-
mated sequences.
The Local IR-EMITTER OUT is
typically used to control a device
that is not part of the main IR
system, such as a TV or DVD player
located within the same room as
the touchpad or electronic volume
controls. IR is routed to an emitter
or IR distribution block connected to
the Local IR output in two ways:
Warning: The connection
labeled “+1ꢀ Volts Out” is a
voltage output. Do not con-
nect a power supply to this
connection!
1. Any IR signal that is received from
the Local IR-RECEIVER IN is sent
out both the Local IR-EMITTER
OUT and the system IR output.
2. IR signals may be specified in
programming as “Local” and be
routed through the Local IR-EMIT-
TER OUT.
Connect IR-EMITTER OUT and
-GROUND as shown here.
Controlling a single local device
Controlling multiple local devices
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Local IR Input
Note: In certain cases, the built-in
IR sensor on the Olé-ꢀSF can be
flooded with plasma TV interference
or other ambient light interference.
In this case, connect a plasma-
friendly IR sensor to the Local IR
Input and disable the built-in IR
sensor in SunTools.
The Local IR-RECEIVER IN is
typically used to connect an external
IR sensor to the touchpad. Typical
applications include a plasma-
friendly IR sensor placed near a TV,
or an auxiliary IR sensor placed in
an area more convenient than the
location of the touchpad. IR signals
that are received by the IR Input are
sent out both the Local IR-EMITTER
OUT and the System Port.
Connect IR-RECEIVER IN,
-GROUND and +1ꢀVOLTS OUT (if
required) as shown below. Consult
the instruction manual that came
with your external equipment
before making connections.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Local Sense In
The LOCAL SENSE IN port allows
a contact-closure to trigger IR se-
quences programmed into the Olé-
ꢀSF using SunTools. Use a motion
sensor to activate a contact-closure
and cause automated actions such
as system power on, drapes closed,
and lights dimmed, for example.
Connect LOCAL SENSE IN and
-GROUND to a contact-closure
device as shown below.
Contact-Closure
Device
1ꢁ
Download from Www.Somanuals.com. All Manuals Search And Download.
System Connections
Zone ꢀ Control
NOTE: The two TP (touchpad)
ports on your Sunfire receiver or
processor are identical.
The most common application
(and default configuration out of
the box) is to use your Olé-2SF as
a Zone ꢀ controller. Without any
programming you will be able to:
All programming is stored in the
Olé-2SF, so to reconfigure your
Olé-ꢀSF to control the main zone, or
to add source IR control (play/stop/
pause on a CD player, for example),
you will need to connect the Olé-
ꢀSF to your PC for programming.
•
•
Select Zone ꢀ sources
Adjust Zone ꢀ volume (with feed-
back)
•
Control the AM/FM/SIRIUS tuners
(with RDS and metadata feed-
back)
•
Basic control of VIA!migo iPod
cradle (with metadata feedback)
•
Adjust Zone ꢀ bass and treble
ZONE 2 Olé-2SF
ZONE 2 SPEAKERS
CAT-5
USE EITHER
CONNECTION
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Home Theater Control
(PC required)
•
•
Select Main Zone sources
The Olé-ꢀSF is perfectly suited as
an in-wall Home Theater controller.
You may want to include one by the
entrance to startup or shutdown the
system. In this case, you will need
to connect your Olé-ꢀSF to a PC
running SunTools to reconfigure it
to control the main zone. The main
zone template allows you to control
the following:
Adjust Main Zone volume (with
feedback)
•
Control the AM/FM/SIRIUS tuners
(with RDS and metadata feed-
back)
•
Basic control of VIA!migo iPod
cradle (with metadata feedback)
•
•
•
Adjust Main Zone bass and treble
Select DSP modes
Control OSD menu functions
NOTE: Of course you can go
wild with custom programming - the
above functions are simply included
in the default template and repre-
sent the most commonly needed
functions.
MAIN ZONE Olé-2SF
CAT-5
MAIN ZONE SPEAKERS
USE EITHER
CONNECTION
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming
The Olé-ꢀSF must be pro-
To download a SunTools
project:
grammed with Sunfire’s SunTools
setup software using a PC running
Windows XP. Downloads are facili-
tated through the USB download
port on the front of the unit.
•
Ensure that your PC is running
the latest version of SunTools
software. Visit sunfire.com for
software downloads and updates.
Note: A standard USB-A to USB-
mini-B cable must be utilized for
programming and is not included
with the Olé-ꢀSF.
•
•
Remove the wall plate to access
the USB download port.
Connect a standard USB-A to
USB-mini-B cable between a
USB port on the PC and the USB
download port on the front of the
Olé-ꢀSF touchpad.
• Navigate to the SunTools Olé
transfer page to begin the transfer.
•
Wait until “DONE OK” is displayed
on the Olé-ꢀSF’s screen before
disconnecting the USB cable from
the USB Download Port.
USB download port
USB-A to USB-mini-B cable
Laptop running
SunTools
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Feature Enable/Disable:
Speaker
4. Press and hold the "SELECT" but-
ton for five seconds. Depending
on the correct state of the sensor,
a message will be displayed:
The Olé-ꢀSF contains a small
speaker that allows audible feed-
back signals to be heard as a result
of button pushes. This feature can
be disabled in the SunTools setup
software.
“Release button to ENABLE
sensor”
or
IR Sensor
"Release button to DISABLE
sensor"
The Olé-ꢀSF features a built-in IR
Sensor. IR signals from a hand-held
IR remote control pass through the
IR sensor and travel to the head-
end location where they control
IR sources located there. These
sources may be connected to a 3rd-
party Multi-Zone Controller or an IR
distribution network.
Once the button is released, a
confirmation message will be sent:
Either:
"LIGHT SENSOR ENABLED"
or
"LIGHT SENSOR DISABLED"
When the Light Sensor is enabled,
the Olé-ꢀSF touchpad's backlight
will brighten or dim depend-
The IR Sensor can be disabled in
SunTools setup software.
ing on the room's ambient light
conditions. When the sensor is
disabled, the Olé-ꢀSF remains at
full brightness no matter what the
ambient light conditions are like.
Light Sensor Enable/Dis-
able
The Olé-ꢀSF touchpad has a light
sensor feature.
1. Install the unit in the wall, using
the wall plate that will be used in
the final installation.
ꢀ. Adjust the room lighting to the
brightest setting possible.
3. Select a source on the touchpad.
The light sensor function only
works when the unit displays the
source icon screen.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Viewing Angle
Dimensions
With Wall Plate
180° up/down,180° left/right
Height
4 ꢁ/8" (117 mm)
Operating Temp
Width
Depth
4.ꢁ/8" (117 mm)
1 3/16" (30 mm)
3ꢀ°F-104°F / 0°C-40°C
OLED Display
Without Wall Plate
Type: 2” Organic LED (OLED)
Height
4 7/16" (112 mm)
Colors: ꢀꢁꢀK
Width
Depth
4. 7/16" (112 mm)
1 1/8" (26 mm)
Resolution: 160 pixels (W) x 128
pixels (H)
Fits into a 3ꢀ cu in. double-gang
electrical box
Connections
Weight
System Port: RJ-4ꢁ
Interface Port: ꢁ-position screw
terminal
14 oz./0.4kg
Shipping Weight
Download Port: Mini USB
16 oz./0.4ꢁkg
Wiring Requirements
Cat-ꢁ
Power Requirements
1ꢀVDC/1ꢁ0mA or 16VDC/1ꢁ0mA
Power Consumption
Each Olé-ꢀSF touchpad draws
1ꢁ0mA in either 1ꢀV or 16V mode
© ꢀ008 Sunfire, LLC.
All rights reserved. Sunfire, LLC re-
serves the right to improve its products
at any time. Therefore, specifications
are subject to change without notice.
Manual 913-144-00 Rev A
ꢀ0
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Power
Symptom
Cause
Solution
Olé-ꢀSF
does not
power up.
1. RJ-4ꢁ plug
Verify wiring pinout and RJ-4ꢁ
crimp. Correct by re-crimping
RJ-4ꢁ to Cat-ꢁ cable.
crimped incorrectly;
or wiring pinout of
RJ-4ꢁ reversed.
ꢀ. Break in Cat-ꢁ
between Zone and
“Head-End”.
Check RJ-4ꢁ to RJ-4ꢁ con-
nections with cable tester.
3. Receiver or
processor power is
disconnected.
Check AC outlet for power (re-
set breaker if tripped) making
sure power cord is securely
plugged in.
ꢀ1
Download from Www.Somanuals.com. All Manuals Search And Download.
IR
Symptom
Cause
Solution
No control
of IR
sources.
1. Programming:
missing or incorrect
IR commands.
Verify and correct program-
ming. Test IR commands from
SunTools.
ꢀ. Wiring: Incorrect
wiring between Zone
and ‘Head-End”.
Verify and correct wiring.
3. Wiring: IR emitter
connected to wrong
source IR port of
Verify port connection and
correct.
multi-room controller.
IR emitter defective.
Replace IR emitter.
Intermit-
tent source
control.
IR flooding.
Check to see if any ambi-
ent light is shining on built in
IR receiver or in direct line
with plasma TV noise. If the
Olé-ꢀSF cannot be relocated,
disable the IR receiver in
SunTools setup software and
use a plasma friendly external
receiver as shown on page 14
of this manual. If installed in
conjunction with an 3rd-party
multi-room controller, please
refer to its own troubleshooting
steps.
ꢀꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
Sunfire Warranty
Sunfire, LLC is proud of its products that
have been built with care using advanced
technology and premium component parts.
Your unit has been crafted to perform
properly for many years. Sunfire offers the
following Warranty to you, the owner of a
new Sunfire product:
Some states do not allow limitations on how
long an implied warranty lasts and/or do not
allow the exclusion or limitation of incidental
or consequential damages, so the above limi-
tations or exclusions may not apply to you.
This Warranty gives you specific legal rights,
and you may also have other rights which
vary from state to state. We suggest that you
attach your purchase receipt to this Warranty
and keep these in a safe place. Thank you
for your choice of a Sunfire product.
The Sunfire Warranty for the Olé-ꢀSF
touchpad is in effect for one year from the
date of original retail purchase. The Sunfire
Warranty covers defects in materials and
workmanship. The following, however, are
excluded:
Service Assistance
We suggest that you read the Limited War-
ranty completely to fully understand your
Warranty/Service coverage.
a) Damage caused during shipment.
b) Damage caused by accident, misuse,
abuse of operation contrary to the in-
structions specified in the Sunfire user’s
manual
If your Sunfire product ever requires service,
write to us, or call:
Sunfire, LLC
Technical Services Department
P.O. Box 1ꢁ89
Snohomish, WA 98ꢀ90
support@sunfire.com
Tel (425) 335-4748
c) Units where the serial number has been
defaced, modified or removed,
d) Damage resulting from modification
or attempted repair by any person not
authorized in writing by Sunfire, LLC.
Fax (425) 335-4746
e) Units purchased from unauthorized deal-
ers.
You will be directed to an authorized Sunfire
Service Station or receive instructions to ship
the unit to the factory. Please save the origi-
nal shipping carton and packing materials in
case shipping is required. Please do not ship
Parcel Post.
The Sunfire Warranty extends to the original
owner during the one year warranty period
so long as the original dated purchase re-
ceipt is presented whenever warranty service
is required.
NOTE: Before sending in your unit for
repair, you must call Sunfire for return
authorization (RA).
All implied warranties, including warranties or
merchantability and fitness for particular pur-
poses, are limited in duration to the one year
length of this Warranty, unless otherwise
provided by state law.
Include a complete description of the prob-
lem, indicating how you have it connected,
the associated equipment in your system
and a copy of your purchase receipt. Initial
shipping costs are not paid by Sunfire;
return ground shipping costs will be prepaid
if repairs were covered by the scope of this
Warranty.
Sunfire’s liability is limited to the repair or
replacement, at our option, of any defective
product and shall not in any event include
property or any other incidental or conse-
quential damages which may result from the
failure of this product.
ꢀ3
Download from Www.Somanuals.com. All Manuals Search And Download.
Manual 913-144-00 Rev A
Download from Www.Somanuals.com. All Manuals Search And Download.
|