Euro Plus
2400W Convection
Panel Heater
Instruction Booklet
HE4900
Please read these instructions carefully
and retain for future reference.
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Sunbeam’s Safety Precautions
Safety Precautions for your heater
Sunbeam’s Total Safety System
1
2
3
Features of your Euro Plus Convection
Panel Heater
4
6
7
8
8
9
9
Wall mounting your heater
Attaching the wheels
Using your heater
Restricting the temperature range
Resetting the safety auto shut off
Care and cleaning
Download from Www.Somanuals.com. All Manuals Search And Download.
Sunbeam’s Safety Precautions
Sunbeam are very safety conscious when
• Do not use an appliance for any purpose
other than its intended use.
designing and manufacturing consumer products,
but it is essential that the product user also
exercise care when using an electrical appliance.
Listed below are precautions which are essential
for the safe use of an electrical appliance:
• Do not place an appliance on or near a hot gas
flame, electric element or on a heated oven.
Do not place on top of any other appliance.
• Do not let the power cord of an appliance hang
over the edge of a table or bench top or touch
any hot surface.
• Read carefully and save all the instructions
provided with an appliance.
• Always turn the power off at the power outlet
before you insert or remove a plug. Remove
by grasping the plug - do not pull on the cord.
• For safety reasons and to avoid maintenance
by unskilled persons, some appliances are
‘sealed’ using tamperproof screws. Such
appliances should always be returned to the
nearest Sunbeam Appointed Service Centre
for adjustment or repair if required.
• Turn the power off and remove the plug
when the appliance is not in use and
before cleaning.
• Do not use your appliance with an extension
cord unless this cord has been checked
and tested by a qualified technician or
service person.
• Do not operate any electrical appliance with a
damaged cord or after the appliance has been
dropped or damaged in any manner. If damage
is suspected, return the appliance to the
nearest Sunbeam Appointed Service Centre
for examination, repair or adjustment.
• Always use your appliance from a power
outlet of the voltage (A.C. only) marked
on the appliance.
• For additional protection, Sunbeam
recommend the use of a residual current
device (RCD) with a tripping current not
exceeding 30mA in the electrical circuit
supplying power to your appliances.
• Close supervision is necessary when your
appliance is being used near children or
infirm persons.
• Never leave an appliance unattended while
in use.
• Do not immerse the appliance in water
or any other liquid unless recommended.
• Young children should be supervised to ensure
that they do not play with the appliance.
If you have any concerns regarding the performance and use of your appliance,
Ensure the above safety precautions are understood.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Sunbeam’s Safety Precautions
• This heater becomes hot during use. To avoid
burns, do not let bare skin touch hot surfaces.
If provided, use handles when moving this
heater. Keep combustible materials such as
furniture, pillows, bedding, papers, clothes and
curtains at least 3 feet (90cm) away from the
front of the heater and keep them away from
the sides and rear.
• Do not locate the heater immediately below a
socket outlet.
• Do not use this heater in the immediate
surrounds of a bath, shower, laundry area or
swimming pool.
• Do not insert or allow foreign objects to enter
any ventilation or exhaust openings as this may
cause electric shock or fire, or damage to the
heater.
• Extreme caution is necessary when any heater
is used by or near children or invalids and
whenever the heater is left unattended.
• To prevent a possible fire, do not block air
intakes or exhaust in any manner. Do not use
on soft surfaces, such as beds, where opening
may become blocked.
• Always unplug the heater when not in use.
• Do not use outdoors.
• Do not run the cord of the heater under
carpeting. Do not cover the cord with throw
rugs, runners or other floor coverings. Arrange
the cord away from traffic areas where it will
not be tripped over.
• A heater has hot and arcing or sparing parts
inside. Do not use it in areas where petrol,
paint or flammable liquids are used or stored.
Important instructions – retain for
future use.
If you have any concerns regarding the performance and use of your appliance,
Ensure the above safety precautions are understood.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Features of your Euro Plus heater
Patented SCHWARZ element
The patented heating element is designed to
heat faster than conventional elements. Its
single metal construction ensures optimum
heat transfer from the element into the
surrounding air, to warm the room faster.
Overheat protection
The safety auto shut off system
detects any abnormally high
temperatures within the heater and
automatically switches it off to
prevent overheating.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Thermostat dial
The thermostat dial allows you to set
your desired temperature level.
Accurate to within 1°C, the
electromechanical thermostat monitors
the room’s temperature and
continuously adjusts the heat output to
maintain your selected comfort level.
The element is only powered for as long
as necessary to restore the selected
temperature, ensuring maximum
efficiency.
On/off switch
The on/off switch at the side of the unit
control’s the heater’s operation.
Wall mount bracket
The wall mount bracket is simply
screwed onto the wall for quick and
easy installation.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Wall mounting your heater
Before using your Euro Plus heater ensure it
is securely mounted on a wall.
Wall mounting
For maximum efficiency this heater should
be positioned so that the heat generated
mixes with the maximum volume of air. It
can be installed in any room of the home,
including the bathroom, in accordance with
the instructions below.
A
A = 10 cm
B = 10 cm
C = 75 cm
1. Remove the wall mounting bracket from
the rear of the heater by squeezing the
clips (at A and B in figure 2 below) and
pulling towards you.
Figure 3
Note: any electrical appliances to be fitted in
a bathroom should be installed by a qualified
electrician in accordance with Australian/New
Zealand Standard Wiring Rules. Portable
heaters should not be used in a bathroom.
B
A
Heaters that can be permanently fixed must
be installed so that any controls cannot be
reached by a person using a bath or shower,
as shown in figure 4.
Figure 2
2. Select a suitable location to mount the
heater, ensuring that it is at least 10cm
below any curtains or window furnishings,
10cm from any furniture located to either
side, and 75cm from any furniture placed
in front of the heater, as shown in figure 3.
60cm
60cm
Figure 4
The heater must be mounted horizontally,
with the control panel at the top.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Wall mounting your heater (continued)
3. Mark the first top screw location on the
wall, at least 630mm from the floor or
skirting board. The base of the heater
must be at least 200mm from the floor to
ensure adequate air flow into the air inlet.
Drill the first hole using a suitable drill bit.
7. To place the heater on the bracket, insert
the lower clips first then the top, and push
firmly until it clicks into position, as
shown in figure 5.
4. Measure and mark the second drill hole,
564mm from the first hole. Drill the hole.
5. Measure and mark the bottom screw holes,
289mm below the top two holes. Drill.
6. Position the bracket over the drill holes
and screw into position.
Figure 5
Attaching the wheels
Before attaching the wheels, remove the wall
mounting bracket from the rear of the heater
by pushing down on the top clips and pulling
towards you.
Figure 6
A
B
1. Position the wheel assembly over the base
of the heater, with the vertical bracket to
the rear of the unit, as shown in Figure 6.
2. Align the screw hole in the vertical bracket
(C) with the screw hole in the rear of the
heater. Place the washer on the screw,
insert the screw and fix loosely. Do not
tighten.
C
3. Align the screw holes on the underside of
Once all screws are correctly positioned,
tighten the screw in position C.
the wheel assembly (A and B) with the
holes on the base of the heater. Insert
each screw and washer and tighten.
4. Repeat on the other side.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Using your heater
1. Install the heater in accordance with the
instructions above.
5. Adjust the thermostat dial to your desired
heat level, from 1 to 12.
2. Insert the plug into a 230-240V power
outlet and turn the power on.
6. Once the selected temperature is reached,
the electromechanical thermostat will
constantly monitor the room temperature
and adjust the heat output to maintain it.
3. Ensure that the air inlet vent on the
underside of the heater and the air outlet
are clear of obstructions.
7. To switch the heater off, move the on/off
switch to the off position (O).
4. Move the on/off switch to the on position (I).
Restricting the temperature range
With the aid of two pins at the back of the
unit, you can limit the range of the
2. Insert the pins in the desired position to
limit or fix the rotation of the thermostat
dial as desired.
thermostat dial. Use one pin to lock the
thermostat at a fixed temperature, or two
pins to fix a set temperature range. One pin
determines the upper value, and the other
determines the lower value.
1. To remove the pins from their original
position, move each one back and forth
using a pair of needle nose pliers to loosen
them.
Figure 7
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Resetting the safety auto shut off
The safety auto shut off detects any
abnormally high temperatures within the
heater and shuts it off to prevent
overheating. Should the safety auto shut
off activate and switch off the heater, it
will need to be reset.
2.Unplug the heater and wait 5-10 minutes
for the unit to cool down.
3.After 5-10 minutes, plug the heater in
again and operate as usual.
1.To reset the heater, move the on/off switch
to the OFF position.
Care and cleaning
Ensure that the heater is switched off and
disconnected from the power outlet before
cleaning.
wiping with a damp cloth, or carefully going
across the vent with a vacuum cleaner with
brush attachment.
Carefully wipe the exterior of the heater with
a soft damp cloth and dry thoroughly with a
dry cloth.
Do not use harsh or abrasive cleaners to
clean your heater, as these will damage the
surface.
Over time dust may accumulate on the front
vent of the heater, this can be removed by
is a registered trademark of Sunbeam
Corporation Limited.
© Copyright. SUNBEAM CORPORATION LIMITED 2004.
(INCORPORATED IN N.S.W.) A.C.N. 000 006 771
Sunbeam Corporation is a division of GUD Holdings Ltd.
Euro Plus is a trademark of Sunbeam Corporation Limited.
For more information or advice on this or any other
contact the Sunbeam Consumer Service Line.
Made in France. Due to minor changes in design or
otherwise, the product you buy may differ from the one
shown in this leaflet.
Australia 1800 025 059
New Zealand (09) 912 0747.
Backed by Sunbeam‘s 3 Year Replacement Guarantee and
National Service Network.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Consumer Hotline
Australia
1800 025 059
New Zealand
(09) 912 0747
Consumer information:
is a registered Trademark of Sunbeam
Corporation Limited. ACN 000 006 771.
© Sunbeam Corporation Limited 2002.
Download from Www.Somanuals.com. All Manuals Search And Download.
|