Sun StorEdge™ PCI/PCI-X Dual
Ultra320 SCSI Host Adapter
Installation Guide
Sun Microsystems, Inc.
Part No. 817-5827-13
January 2007, Revision A
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
v
1
2
3
▼
▼
4
7
8
▼
8
9
▼
▼
9
Cabling 15
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
iv Sun StorEdge PCI/PCI-X Dual Ultra320 SCSI Host Adapter Installation Guide • January 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
Preface
This Sun StorEdge PCI/PCI-X Dual Ultra320 SCSI Host Adapter Installation Guide is
intended for experienced system administrators.
Before You Read This Book
Before you install and use the Sun StorEdge™ PCI/PCI-X Dual Ultra320 SCSI host
adapter as described in this manual, you must read and understand the documents
listed in the following table.
Topic
Title
Part Number
Release Notes
Sun StorEdge PCI/PCI-X Dual
Ultra320 SCSI Host Adapter Release
Notes
817-5828-xx
The release notes list supported
cables, platforms, and storage
devices along with other essential
Diagnostics
SunVTS 5.x User Guide
Varies according to the SunVTS
software version being used. A
different version of the SunVTS
software is released with each
release of the Solaris operating
system
SunVTS 5.x Reference Manual
v
Download from Www.Somanuals.com. All Manuals Search And Download.
How This Book Is Organized
■
Chapter 1 describes the Sun StorEdge PCI/PCI-X Dual Ultra320 SCSI host adapter
and explains how to install it on your system, connect it to a storage device, and
test it. It also includes instructions on booting from a hard disk connected to the
host adapter.
■
■
■
Appendix A provides general information and configuration rules about the host
adapter.
Appendix B contains the specifications for the low-voltage differential (LVD) host
adapter.
safety information.
Using UNIX Commands
This document might not contain information on basic UNIX commands and
procedures such as shutting down the system, booting the system, and configuring
devices. See the following for this information:
®
■
Software documentation that you received with your system
Solaris™ operating environment documentation, which is at
■
vi Sun StorEdge PCI/PCI-X Dual Ultra320 SCSI Host Adapter Installation Guide • January 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
Typographic Conventions
*
Typeface
Meaning
Examples
AaBbCc123
The names of commands, files,
and directories; on-screen
computer output
Edit your.loginfile.
Use ls-ato list all files.
% You have mail.
What you type, when contrasted % su
with on-screen computer output
AaBbCc123
Password:
Book titles, new words or terms, Read Chapter 6 in the User’s Guide.
AaBbCc123
words to be emphasized.
Replace command-line variables
with real names or values.
These are called class options.
You must be superuser to do this.
To delete a file, type rmfilename.
*
The settings on your browser might differ from these settings.
Related Documentation
Application
Title
Part Number
Installation
817-5828-xx
Sun StorEdge PCI/PCI-X Dual
Ultra320 SCSI Host Adapter
Release Notes
817-6237-10
Sun StorEdge PCI/PCI-X Dual
Ultra320 SCSI Host Adapter
Guide to Documentation
Preface
vii
Download from Www.Somanuals.com. All Manuals Search And Download.
Accessing Sun Documentation
You can view, print, or purchase a broad selection of Sun documentation, including
localized versions, at:
Ultra320 SCSI Host Adapter Release Notes at Sun’s Network Storage documentation
web site, follow the steps on the next page.
▼ To Access the Release Notes
1. Access the release notes at Sun’s web site by using one of the following methods.
■
■
Alternately, you can go directly to this address:
3. In the documentation list, click the row listing the Sun StorEdge PCI/PCI-X Dual
Ultra320 SCSI Host Adapter Release Notes.
Note – Viewing and printing documents in Adobe® Portable Document Format
(PDF) requires Adobe Acrobat Reader, which is downloadable for free from:
viii Sun StorEdge PCI/PCI-X Dual Ultra320 SCSI Host Adapter Installation Guide • January 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
Third-Party Web Sites
Sun is not responsible for the availability of third-party web sites mentioned in this
document. Sun does not endorse and is not responsible or liable for any content,
advertising, products, or other materials that are available on or through such sites
or resources. Sun will not be responsible or liable for any actual or alleged damage
or loss caused by or in connection with the use of or reliance on any such content,
goods, or services that are available on or through such sites or resources.
Contacting Sun Technical Support
If you have technical questions about this product that are not answered in this
document, go to:
Sun Welcomes Your Comments
Sun is interested in improving its documentation and welcomes your comments and
suggestions. You can submit your comments by going to:
Please include the title and part number of your document with your feedback:
Sun StorEdge PCI/PCI-X Dual Ultra320 SCSI Host Adapter Installation Guide, part
number 817-5827-13
Preface
ix
Download from Www.Somanuals.com. All Manuals Search And Download.
x
Sun StorEdge PCI/PCI-X Dual Ultra320 SCSI Host Adapter Installation Guide • January 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER
1
Installing, Connecting, and Testing
the Host Adapter
This chapter describes the Sun StorEdge PCI/PCI-X Dual Ultra320 SCSI host adapter
and explains how to install it into a host, connect it to SCSI storage devices, test the
installation, and boot from a disk drive connected to the host adapter.
Note – If you are unfamiliar with Ultra320 SCSI configuration guidelines, read
“Ultra320 SCSI Configuration” on page 13 before performing the procedures in this
chapter.
This chapter discusses the following topics:
■
■
■
■
■
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Features
The Sun StorEdge PCI/PCI-X Dual Ultra320 SCSI host adapter is a dual-channel
Ultra320 SCSI to PCI/PCI-X host adapter that provides two Ultra320 SCSI channels.
FIGURE 1-1 Sun StorEdge PCI/PCI-X Dual Ultra320 SCSI Host Adapter
The host adapter includes the following features:
■
Two independent Ultra320 SCSI channels with support for SCSI speeds of up to
320 Mbyte/sec with 16-bit data transfer
■
Four SCSI connectors:
■
Two external 68-pin very high density cable interconnect (VHDCI) right-angle
connectors
■
Two internal 68-pin high density right-angle connectors. .
■
LVD SCSI support for disk arrays, tape libraries, and tape drives:
■
Two 16-bit LVD interfaces with support for up to 15 targets on each SCSI bus
Active LVD termination
■
■
■
32K bytes of NVSRAM (reserved feature)
Backward-compatible with SCSI-2 and SCSI-3 (Ultra1, Ultra2, and Ultra3) devices.
For Sun StorEdge systems qualified and supported with this host adapter, see Sun
StorEdge PCI/PCI-X Dual Ultra320 SCSI Host Adapter Release Notes, 817-5828-xx.
2
Sun StorEdge PCI/PCI-X Dual Ultra320 SCSI Host Adapter Installation Guide • January 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
■
■
512K bytes of Flash ROM for booting in a Sun SPARC or a Sun Solaris x86 OS
processor-based host system
A 64-bit universal type board edge connector that provides:
■
64-bit, 133-MHz PCI-X interface compatibility
■
32-bit/64-bit PCI interface backwards compatibility
Installing the Host Adapter
Before you start, read these instructions, and also read the installation instructions in
the documentation that applies to the storage device(s) to be connected to the host
adapter. Also, before installing the host adapter, read the Sun StorEdge PCI/PCI-X
Dual Ultra320 SCSI Host Adapter Release Notes for required information, including
lists of supported cables and storage devices. Downloading the release notes is
described in “To Access the Release Notes” on page viii
Caution – This host adapter is only for connection to a single-ended (SE) or low-
voltage differential (LVD) device, and it does not work if connected to a high-voltage
differential (HVD) device.
!
Caution – Damage to the HBA can occur as the result of careless handling or
electrostatic discharge (ESD). Always handle the HBA with care to avoid damage to
electrostatic sensitive components.
To minimize the possibility of ESD-related damage, Sun strongly recommends using
both a workstation antistatic mat and an ESD wrist strap. You can get an ESD wrist
strap from any reputable electronics store or from Sun as part number #250-1007.
Observe the following precautions to avoid ESD-related problems:
■
Leave the HBA in its antistatic bag until you are ready to install it in the system.
■
Always use a properly fitted and grounded wrist strap or other suitable ESD
protection when handling the HBA and observe proper ESD grounding
techniques.
■
■
Hold the HBA by the edge of the PCB or mounting bracket, not the connectors.
Place the HBA on a properly grounded antistatic work surface pad when it is out
of its protective antistatic bag.
Chapter 1 Installing, Connecting, and Testing the Host Adapter
Download from Www.Somanuals.com. All Manuals Search And Download.
3
▼ To Prepare for Hardware Installation
1. Read and observe the safety information at the back of this book.
2. Install the Solaris 8 2/04 (minimum required version) operating system on the
host.
3. Install the Solaris 8 2/04 (minimum required version) recommended patch cluster
on the host.
See the Sun StorEdge PCI/PCI-X Dual Ultra320 SCSI Host Adapter Release Notes for
how to download and install the Solaris OS recommended patch cluster.
4. Install any required driver patches on the host.
See the release notes to find the applicable patches for the version of the Solaris OS
that is installed on the host. Also see the release notes for how to download the
driver and any required patches. If needed, see “To Access the Release Notes” on
Caution – If the driver and any required patches described in the release notes are
not installed, you cannot use the host adapter.
!
5. Install the SunVTS software on the host.
The SunVTS software is shipped on the Supplemental Software CD-ROM along with
the Solaris operating system CD-ROM. Read the user’s guide listed in “Before You
Read This Book” on page v for how to install the SunVTS software.
6. Exit the operating environment.
Note – If your system supports the PCI hot-plug capability, refer to the service
To inform any mounted users that the system will be going down, use the shutdown
command. Otherwise, use the init 0command. See the Man Pages for these
commans or the Solaris AnswerBook documentation.
# shutdown
...
ok
7. Power off the system. Refer to the service documentation that came with your
system.
4
Sun StorEdge PCI/PCI-X Dual Ultra320 SCSI Host Adapter Installation Guide • January 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
Caution – Do not disconnect the power cord from the system or from the wall
outlet. This connection provides the ground path necessary to safely remove and
install the printed circuit boards and components without damaging them.
!
8. Choose a PCI-X (or PCI) slot for installing the host adapter.
To maximize performance, use the host system’s 64-bit, 66/133-MHz PCI/PCI-X slot
slot for installing the host adapter.
Note – You can insert the host adapter into a 32-bit PCI slot if no 64-bit PCI-X slots
are available. However, if you do this, the data transmission rate is limited to
standard PCI speed.
Chapter 1 Installing, Connecting, and Testing the Host Adapter
Download from Www.Somanuals.com. All Manuals Search And Download.
5
9. Unpack the host adapter.
You should have the following items:
■
Sun StorEdge PCI/PCI-X Dual Ultra320 SCSI host adapter (Figure 1-1)
Antistatic wrist strap
■
Note – Leave the host adapter in the protective bag until you are ready to install it.
J6 connector
J4 connector
PCI/PCI-X connector
J2 (Channel A)
J3 (Channel B)
FIGURE 1-2 Sun StorEdge PCI/PCI-X Dual Ultra320 SCSI Host Adapter
VHDCI Connectors
The host adapter is shown in Figure 1-2. The Very High Density Cable Interconnect
(VHDCI) connectors are for the VHDCI cables that are used to connect the host
adapter to the storage device.
The next section provides instructions on how to install the host adapter in your
system.
6
Sun StorEdge PCI/PCI-X Dual Ultra320 SCSI Host Adapter Installation Guide • January 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
▼ To Install the Host Adapter
1. Open the system.
Refer to your system documentation for information about how to open the system.
2. Attach the wrist strap between your wrist and a metal part of the system chassis.
3. For systems with a standby-type power switch, disconnect the power cord.
Standby-type power switches have a
icon.
The wrist strap between you and the chassis provides the ground path necessary to
safely remove and install the printed circuit boards and components without
damaging them.
4. Remove the filler panel for the desired slot.
Refer to the system documentation for information about removing filler panels.
5. Remove the host adapter from its protective bag.
6. Install the host adapter in the selected PCI/PCI-X slot in your system.
choose a slot. Also, refer to the system’s hardware documentation for information
about mounting details (mounting holes, standoff locking/unlocking, and screws to
secure the card).
Caution – Using excessive force can bend or damage the host adapter edge
connector. Make sure that the edge connector is properly aligned before pressing the
adapter into place. The bracket around the two external connectors should fit into
!
7. Remove the wrist strap.
8. Close the system.
The next two sections describe how to connect the host adapter to one or more
storage devices and how to test the host adapter.
Chapter 1 Installing, Connecting, and Testing the Host Adapter
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Connecting the Host Adapter
Before you connect the host adapter to the storage device(s), do the following:
■
Refer to the release notes for the lists of supported cables and storage devices.
Downloading the release notes is described in “To Access the Release Notes” on
■
■
information on configuration for Ultra320 SCSI devices.
Refer to your system documentation and the storage device installation manual
for specific cabling instructions.
▼ To Connect SCSI Cable(s) From the Host
Adapter to the Storage Device(s)
1. Connect the host adapter to the storage device(s) using the appropriate cable(s).
Refer to Table 1-1 for SCSI interface connection information.
TABLE 1-1
Sun StorEdge PCI/PCI-X Dual Ultra320 SCSI Host Adapter Interfaces
SCSI Interface
Channel A
Channel B
External Connector
Internal Connector
J2
J3
J6
J4
8
Sun StorEdge PCI/PCI-X Dual Ultra320 SCSI Host Adapter Installation Guide • January 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
Testing the Host Adapter
You should test the host adapter installation using the probe-scsi-all command
and, if the newly attached device is a disk array, with the SunVTS software.
▼ To Test the Installation Using the probe-scsi-
allCommand
1. If you have disconnected the power cable, reconnect it.
2. Power on the connected storage device(s) and then power on the host.
3. Bring the system down to the okprompt at run level 0.
Note – If the host starts to reboot, interrupt the reboot process by
pressing the Stop and A keys simultaneously.
4. At the okprompt, enter the probe-scsi-allcommand to verify that the system
recognizes the host adapter.
The probe-scsi-allcommand displays the SCSI devices connected to the host, as
shown in the following screen example.
ok probe-scsi-all
/pci@4,2000/pci@1/scsi@2
Target 0
Unit 0 DISK SEAGATE ST336605LSUN36G 0238
/pci@4,2000/pci@1/scsi@2,1
Target 0
Unit 0 DISK SEAGATE ST336605LSUN36G 0238
In this example, the first SCSI port (scsi@2) has one disk drive connected
(Target 0). The second SCSI port (scsi@2,1) also has one disk drive connected
(Target 0). In the illustration of the host adapter in Figure 1-1, the first SCSI port is
labeled as Channel A; the second SCSI port as Channel B.
Chapter 1 Installing, Connecting, and Testing the Host Adapter
Download from Www.Somanuals.com. All Manuals Search And Download.
9
▼ To Test the Installation With the SunVTS
Software
Use the the SunVTS software to test a disk on a newly-attached disk array, to verify
that the host adapter is properly installed.
For details about running the the SunVTS software, refer to the SunVTS 5.X User’s
Guide and the SunVTS 5.X Test Reference Manual.
1. As superuser, open the SunVTS window.
# /opt/SUNWvts/bin/sunvts
2. From the System Map, select a disk drive that is in an array connected to the host
adapter.
3. Start the disk test.
4. Verify that no errors have occurred by checking the SunVTS status window.
5. If no problems occur, stop the SunVTS software.
Your host adapter is now ready to run applications.
Note – If problems occur, please contact your service provider for assistance.
10
Sun StorEdge PCI/PCI-X Dual Ultra320 SCSI Host Adapter Installation Guide • January 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
Booting the Host Adapter
The Sun StorEdge PCI/PCI-X Dual Ultra320 SCSI host adapter uses the mptdriver,
which is included with the Solaris operating system beginning with the Solaris 8
2/04 OS release and the Solaris 9 4/04 OS release. This enables you to “warm” boot
directly from a hard disk connected to the host adapter if that disk has at least the
Solaris 8 2/04 OS release or the Solaris 9 4/04 OS release installed.
Note – A “warm” boot requires that the hard disk attached to the host adapter be
powered on and available at the time the server is powered up. A “cold” boot,
where both the server and hard disk are powered up at the same time, is not
supported by the mptdriver.
After booting, you should install any required patches for the mptdriver. Refer to
the Sun StorEdge PCI/PCI-X Dual Ultra320 SCSI Host Adapter Release Notes for
instructions on dowloading and installing mptdriver patches. To view the Release
Note – The Sun StorEdge 3310 standalone SCSI array is presently limited to
Ultra160 SCSI bus speeds only. Normally, the host adapter automatically lowers the
transfer speed for attached storage devices that are not Ultra320 capable. However,
for the Sun StorEdge 3310 standalone SCSI array, you must create an mpt.conf file
to limit the Sun StorEdge PCI/PCI-X Dual Ultra320 SCSI host adapter to Ultra160
SCSI bus speeds.
For instructions on creating the mpt.conffile, refer to the Sun StorEdge PCI/PCI-X
Chapter 1 Installing, Connecting, and Testing the Host Adapter
Download from Www.Somanuals.com. All Manuals Search And Download.
11
12
Sun StorEdge PCI/PCI-X Dual Ultra320 SCSI Host Adapter Installation Guide • January 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
A
Ultra320 SCSI Configuration
This appendix provides general information about Ultra320 SCSI configuration
rules. The following topics are discussed:
■
■
■
■
Target Devices
For Ultra320 SCSI performance of up to 320 Mbytes/sec, there can be a maximum of
15 devices connected to each port on the host adapter.
The available target addresses (SCSI IDs) for each port on the host adapter are 0
through F.
Note – The SCSI ID of 7 is reserved for the host adapter.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Bus Length
The maximum SCSI bus length is determined by the SCSI bus type (that is, the
number of devices connected).
Table A-1 shows the maximum SCSI bus lengths for Ultra320 SCSI with a 8/16-bit
bus width.
TABLE A-1 Bus Restrictions
SCSI Type
Peak
MBytes
/sec
Single-Ended
*
LVD
No. of Devices
Max Length
No. of Devices
Max Length
SCSI-2
Narrow
10
20
3
3
8
25
12
25
12
2
8
2
16
Wide
16
SCSI-3 Ultra1
Narrow
20
40
1.5
3
1.5
3
8
4
8
4
25
12
25
12
2
8
2
16
Wide
SCSI-3 Ultra2
Narrow
\
40
80
N/S
N/S
N/S
N/S
25
12
25
12
2
8
2
16
Wide
SCSI-3 Ultra3
Narrow
80
N/S
N/S
N/S
N/S
25
12
25
12
2
8
2
16
Wide
160
SCSI-3 Ultra320
Narrow
160
320
N/S
N/S
N/S
N/S
25
12
25
12
2
8
2
16
Wide
*
This maximum length (shown in meters) must include the internal bus length of your system. Sun qualifies
cable lengths of only up to 10 meters (22.8 feet).
\ N/S = not supported
14 Sun StorEdge PCI/PCI-X Dual Ultra320 SCSI Host Adapter Installation Guide • January 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
Cabling and Termination
Use the following cabling guidelines to ensure proper device cabling and
termination.
Cabling
In order to maintain Ultra320 SCSI performance, all cables used must be Ultra320
SCSI compliant.
Termination
■
The SCSI bus must be correctly terminated at the end of the bus. Most Sun
devices use auto-termination. See the documentation that came with the device.
This host adapter has active terminators with an automatic means of enabling and
disabling the termination. All the termination circuit derives its power from the
PCI or SCSI bus. When the PCI bus power is removed, active SCSI termination is
maintained if the other SCSI device supplies power to the Term Pwr pins of the
SCSI bus.
■
Appendix A
Ultra320 SCSI Configuration
15
Download from Www.Somanuals.com. All Manuals Search And Download.
SCSI Symbols
One of the four following symbols is placed near a SCSI port to indicate which type
of SCSI the port is using. The icon may appear alone or with descriptive text.
SE
LVD
LVD/MSE
HVD
Acronym
Meaning
SE
single-ended
LVD
MSE
HVD
low-voltage differential
multi-mode single ended
high-voltage differential
16 Sun StorEdge PCI/PCI-X Dual Ultra320 SCSI Host Adapter Installation Guide • January 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
B
Specifications
The chapter contains the specifications for the low-voltage differential (LVD) Sun
StorEdge PCI/PCI-X Dual Ultra320 SCSI host adapter.
The following topics are discussed:
■
■
■
■
■
Physical Dimensions
TABLE B-1 Physical Dimensions
Dimension
Measurement
Board Without Bracket
Board With Bracket
Length
Width
Height
Weight
7.3 inches (185 meters)
6.9 inches
(175 millimeters)
5.0 inches
(127 millimeters)
4.2 inches
(107 millimeters)
.85 inches
(21.6 millimeters)
.5 inches
(12.7 millimeters)
6.0 oz (43.42 g)
N/A
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Power Requirements
TABLE B-2 Power Requirements
Voltage
Maximum Current
5V 5%
3.3V 9%
12V 5%
3A
0.0A
0.0A
Performance Specifications
TABLE B-3 Performance Specifications
Feature
Specification
PCI/PCI-X bus clock frequency
PCI data burst rate
33 MHz, 66 MHz, and 133 MHz
*
264 MBps @33 MHz,
528 MBps @66 MHz,
1064 MBps @133 MHz
SCSI synchronous max imum transfer rate
PCI data/address lines
PCI modes
320 MBps (wide)
AD63-0
Master/slave
SCSI interface
Low-voltage differential
SCSI bus parity
Yes
Yes
Yes
Yes
SCSI cyclic redundancy check (CRC)
SCSI 8-bit bus devices
SCSI 16-bit bus devices
*
MBps = megabytes per second
18 Sun StorEdge PCI/PCI-X Dual Ultra320 SCSI Host Adapter Installation Guide • January 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
PCI Edge Connector Pin Definitions
TABLE B-4 PCI Edge Connector Pin Definitions J1B (Top)
Pin
1
Description
-12V
Pin
Description
Pin
Description
Pin
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
Description
GND
25 +3.3V
26 C_BE3
27 AD23
28 GND
29 AD21
30 AD19
31 +3.3V
49 GND
50 KEYWAY
51 KEYWAY
52 AD08
53 AD07
54 +3.3V
55 AD05
56 AD03
57 GND
58 AD01
59 3V/5V
60 ACK64
61 +5V
2
AD[55]
AD[53]
GND
TCK
3
GND
4
TDO
5
AD[51]
AD[49]
+5V/+3.3V
AD[47]
AD[45]
GND
+5V
6
+5V
7
INTB
AD17
8
INTD
32
9
GND (PRSNT1)
RESERVED
GND (PRSNT2)
KEYWAY
KEYWAY
RESERVED
GND
33 C_BE2
34 GND
35 IRDY
36 +3.3V
37 DEVSEL
38 GND
39 LOCK
40 PERR
41 +3.3V
42 SERR
43 +3.3V
44 C_BE1
45 AD14
46 GND
47 AD12
48 AD10
10
11
12
13
14
15
16
17
18
19
20
21
AD[43]
AD[41]
GND
AD[39]
AD[37]
+5V/+3.3V
AD[35]
AD[33]
GND
62 +5V
63
64
65
66
67
68
69
70
71
72
RESERVED
GND
CLK
C/BE[6]#
C/BE[4]#
GND
GND
REQ
3V/5V
AD31
AD[63]
RESERVED
RESERVED
AD[61]
AD29
+5V/+3.3V
AD[59]
22 GND
23 AD27
24 AD25
94 GND
AD[57]
Appendix B
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
19
TABLE B-5 PCI Edge Connector Pin Definitions J1A (Bottom)
Pin
1
Description
TRST
Pin
Description
Pin
Description
Pin
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
Description
AD[56]
AD[54]
+5V/+3.3V
AD[52]
AD[50]
GND
25 AD24
26 IDSEL
27 +3.3V
28 AD22
29 AD20
30 GND
31 AD18
49 AD09
50 KEYWAY
51 KEYWAY
52 C_BE0
53 +3.3V
54 AD06
55 AD04
56 GND
57 AD02
58 AD00
59 3V/5V
60 REQ64
61 +5V
2
+12V
3
TMS
4
TDI
5
+5V
6
INTA
7
AD[48]
AD[46]
GND
INTC
8
AD16
+5V
32
9
RESERVED
3V/5V
RESERVED
KEYWAY
KEYWAY
RESERVED
RST
33 +3.3V
34 FRAME
35 GND
36 TRDY
37 GND
38 STOP
39 +3.3V
40 SDONE
41 SBO
10
11
12
13
14
15
16
17
18
19
20
21
AD[44]
AD[42]
+5V/+3.3V
AD[40]
AD[38]
GND
62 +5V
63
64
65
66
67
68
69
70
71
72
GND
C/BE[7]#
C/BE[5]#
+5V/+3.3V
PAR64
AD[36]
AD[34]
GND
3V/5V
GNT
GND
42 GND
43 PAR
AD[32]
RESERVED
GND
RESERVED
AD30
AD[62]
GND
44 AD15
45 +3.3V
46 AD13
47 AD11
48 GND
+3.3V
AD[60]
AD[58]
GND
22 AD28
23 AD26
24 GND
RESERVED
20 Sun StorEdge PCI/PCI-X Dual Ultra320 SCSI Host Adapter Installation Guide • January 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
SCSI Connector Pin Definitions
34
68
1
35
VHDCI Connector
34
68
1
35
Internal SCSI Connector
FIGURE B-1 VHDCI and Internal SCSI Connectors
TABLE B-6 SCSI Connector Pin Definitions
Pin
1
Description
+SD(12)
+SD(13)
+SD(14)
+SD(15)
+SDP(1)
GND
Pin
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
Description
+RST
Pin
Description
SD(6)-
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
2
+MSG
+SEL
SD(7)-
3
SDP-
4
+C/D
Cable Sense (GND)
TERMPWR
TERMPWR
OPEN
5
+REQ
6
+I/O
7
+SD(0)
GND
8
+SD(1)
+SD(8)
+SD(9)
+SD(10)
+SD(11)
SD(12)-
SD(13)-
SD(14)-
SP(15)-
SDP(1)-
GND
ATN-
9
+SD(2)
GND
10
11
12
13
14
15
16
17
+SD(3)
BSY-
+SD(4)
ACK-
+SD(5)
RST-
+SD(6)
MSG-
+SD(7)
SEL-
+SDP
C/D-
DIFFSENS
TERMPWR
REQ-
I/O-
Appendix B
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
21
TABLE B-6 SCSI Connector Pin Definitions (Continued)
Pin
18
19
20
21
22
23
Description
TERMPWR
OPEN
Pin
41
42
43
44
45
46
Description
SD(0)-
SD(1)-
SD(2)-
SD(3)-
SD(4)-
SD(5)-
Pin
64
65
66
67
68
Description
GND
SD(8)-
+ATN
SD(9)-
GND
SD(10)-
SD(11)-
+BSY
+ACK
22 Sun StorEdge PCI/PCI-X Dual Ultra320 SCSI Host Adapter Installation Guide • January 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
Declaration of Conformity
Compliance Model Number:
Product Family Name:
LSI22320-SR
Sun StorEdge PCI/PCI-X Dual Ultra320 SCSI Host Adapter (SGXPCI2SCSILM320-Z)
EMC
USA - FCC Class B
This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This equipment may not cause harmful interference.
2. This equipment must accept any interference that may cause undesired operation.
European Union
This equipment complies with the following requirements of the EMC Directive 89/336/EEC:
As Telecommunication Network Equipment (TNE) in Both Telecom Centers and Other Than Telecom Centers per (as applicable):
EN300-386 V.1.3.2 (2003-05) Required Limits:
EN 55022:1994 +A1:1995 +A2:1997 Class B
EN 61000-3-2:2000
EN 61000-3-3:1995 +A1:2000
IEC 61000-4-2
Pass
Pass
6 kV (Direct), 8 kV (Air)
IEC 61000-4-3
3 V/m 80-1000MHz, 10 V/m 800-960 MHz, and 1400-2000 MHz
IEC 61000-4-4
1 kV AC and DC Power Lines, 0.5 kV Signal Lines
IEC 61000-4-5
2 kV AC Line-Gnd, 1 kV AC Line-Line and Outdoor Signal Lines, 0.5 kV Indoor signal Lines > 10m
IEC 61000-4-6
3 V
IEC 61000-4-11
Pass
As Information Technology Equipment (ITE) Class B per (as applicable):
EN55022:1994 +A1 1995 +A2:1997 Class B
EN 61000-3-2:2000
EN 61000-3-3:1995 +A1:2000
Pass
Pass
EN 55024:1998 +A1: 2001 +A2:2003 Required Limits:
IEC 61000-4-2
IEC 61000-4-3
IEC 61000-4-4
IEC 61000-4-5
IEC 61000-4-6
IEC 61000-4-8
IEC 61000-4-11
4 kV (Direct), 8 kV (Air)
3 V/m
1 kV AC Power Lines, 0.5 kV Signal and DC Power Lines
1 kV AC Line-Line and Outdoor Signal Lines, 2 kV AC Line-Gnd, 0.5 kV DC Power Lines
3 V
1 A/m
Pass
Safety: This equipment complies with the following requirements of the Low Voltage Directive 73/23/EEC:
EC Type Examination Certificates:
EN60950-1:2001, First Edition
IEC 60950-1:2001, 1st Edition
TÜV Rheinland Certificate No.
CB Scheme Certificate No.
Evaluated to all CB Countries
UL 60950:2000, 3rd Edition, CSA C22.2 No. 60950-00
File:
Supplementary Information: This equipment was tested and complies with all the requirements for the CE Mark.
This equipment complies with the Restriction of Hazardous Substances (RoHS) directive
2002/95/EC.
/S/
/S/
Dennis P. Symanski
DATE
Donald Cameron
DATE
Worldwide Compliance Office
Sun Microsystems, Inc.
4150 Network Circle, MPK15-102
Santa Clara, CA 95054, U.S.A.
Tel: 650-786-3255
Program Manager/Quality Systems
Sun Microsystems Scotland, Limited
Blackness Road, Phase I, Main Bldg.
Springfield, EH49 7LR
Scotland, United Kingdom
Tel: +44 1 506 672 539
Fax: +44 1 506 670 011
Fax: 650-786-3723
24 Sun StorEdge PCI/PCI-X Dual Ultra320 SCSI Host Adapter Installation Guide • January 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix C
Declaration of Conformity
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Regulatory Compliance Statements
Your Sun product is marked to indicate its compliance class:
•
•
•
Federal Communications Commission (FCC) — USA
Department of Communications (DOC) — Canada
Voluntary Control Council for Interference (VCCI) — Japan
Please read the appropriate section that corresponds to the marking on your Sun product before attempting to install the
product.
FCC Class A Notice
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required
to correct the interference at his own expense.
Shielded Cables: Connections between the workstation and peripherals must be made using shielded cables in order to
maintain compliance with FCC radio frequency emission limits. Networking connections can be made using unshielded
twisted-pair (UTP) cables.
Modifications: Any modifications made to this device that are not approved by Sun Microsystems, Inc. may void the
authority granted to the user by the FCC to operate this equipment.
FCC Class B Notice
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
•
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/television technician for help.
Shielded Cables: Connections between the workstation and peripherals must be made using shielded cables in order to
maintain compliance with FCC radio frequency emission limits. Networking connections can be made using unshielded
twisted pair (UTP) cables.
Modifications: Any modifications made to this device that are not approved by Sun Microsystems, Inc. may void the
authority granted to the user by the FCC to operate this equipment.
26 Sun StorEdge PCI/PCI-X Dual Ultra320 SCSI Host Adapter Installation Guide • January 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
Depending on the type of power switch your device has,
one of the following symbols may be used:
Safety Agency Compliance
Statements
Read this section before beginning any procedure. The
following text provides safety precautions to follow when
installing a Sun Microsystems product.
On – Applies AC power to the system.
Off – Removes AC power from the system.
Safety Precautions
For your protection, observe the following safety
precautions when setting up your equipment:
Standby – The On/Standby switch is in the
standby position.
■
■
Follow all cautions and instructions marked on the
equipment.
Ensure that the voltage and frequency of your power
source match the voltage and frequency inscribed on
the equipment’s electrical rating label.
Modifications to Equipment
Do not make mechanical or electrical modifications to the
equipment. Sun Microsystems is not responsible for
regulatory compliance of a modified Sun product.
■
Never push objects of any kind through openings in
the equipment. Dangerous voltages may be present.
Conductive foreign objects could produce a short
circuit that could cause fire, electric shock, or damage
to your equipment.
Placement of a Sun Product
Caution – Do not block or cover the
openings of your Sun product. Never place a
Sun product near a radiator or heat register.
Failure to follow these guidelines can cause
overheating and affect the reliability of your
Sun product.
Symbols
The following symbols may appear in this book:
Caution – There is a risk of personal injury
and equipment damage. Follow the
instructions.
Noise Level
In compliance with the requirements defined in DIN 45635
Part 1000, the workplace-dependent noise level of this
product is less than 70 db(A).
Caution – Hot surface. Avoid contact.
Surfaces are hot and may cause personal
injury if touched.
Caution – Hazardous voltages are present.
To reduce the risk of electric shock and danger
to personal health, follow the instructions.
Appendix C Declaration of Conformity, Regulatory, and Safety Information
Download from Www.Somanuals.com. All Manuals Search And Download.
27
The following caution applies only to devices with multiple
power cords:
SELV Compliance
Safety status of I/O connections comply to SELV
requirements.
Caution – For products with multiple
power cords, all power cords must be
disconnected to completely remove power
from the system.
Power Cord Connection
Caution – Sun products are designed to
work with power systems having a grounded
neutral (grounded return for DC-powered
products). To reduce the risk of electric shock,
do not plug Sun products into any other type
of power system. Contact your facilities
manager or a qualified electrician if you are
not sure what type of power is supplied to
your building.
Battery Warning
Caution – There is danger of explosion if
batteries are mishandled or incorrectly
replaced. On systems with replaceable
batteries, replace only with the same
manufacturer and type or equivalent type
recommended by the manufacturer per the
instructions provided in the product service
manual. Do not disassemble batteries or
attempt to recharge them outside the system.
Do not dispose of batteries in fire. Dispose of
batteries properly in accordance with the
manufacturer’s instructions and local
regulations. Note that on Sun CPU boards,
there is a lithium battery molded into the real-
time clock. These batteries are not customer
replaceable parts.
Caution – Not all power cords have the
same current ratings. Do not use the power
cord provided with your equipment for any
other products or use. Household extension
cords do not have overload protection and are
not meant for use with computer systems. Do
not use household extension cords with your
Sun product.
System Unit Cover
You must remove the cover of your Sun computer system
unit to add cards, memory, or internal storage devices. Be
sure to replace the cover before powering on your computer
system.
The following caution applies only to devices with a
Standby power switch:
Caution – Do not operate Sun products
without the cover in place. Failure to take this
precaution may result in personal injury and
system damage.
Caution – The power switch of this product
functions as a standby type device only. The
power cord serves as the primary disconnect
device for the system. Be sure to plug the
power cord into a grounded power outlet that
is nearby the system and is readily accessible.
Do not connect the power cord when the
power supply has been removed from the
system chassis.
28
Sun StorEdge PCI/PCI-X Dual Ultra320 SCSI Host Adapter Installation Guide • January 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
Rack System Warning
CD and DVD Devices
The following warnings apply to Racks and Rack Mounted
The following caution applies to CD, DVD, and other
systems.
optical devices.
Caution – For safety, equipment should
always be loaded from the bottom up. That is,
install the equipment that will be mounted in
the lowest part of the rack first, then the next
higher systems, etc.
Caution – Use of controls, adjustments, or
the performance of procedures other than
those specified herein may result in hazardous
radiation exposure.
Conformité aux normes de sécurité
Caution – To prevent the rack from tipping
during equipment installation, the anti-tilt bar
on the rack must be deployed.
Veuillez lire attentivement cette section avant de
commencer. Ce texte traite des mesures de sécurité qu’il
convient de prendre pour l’installation d’un produit Sun
Microsystems.
Caution – To prevent extreme operating
temperature within the rack insure that the
maximum temperature does not exceed the
product’s ambient rated temperatures.
Mesures de sécurité
Pour votre sécurité, nous vous recommandons de suivre
scrupuleusement les mesures de sécurité ci-dessous lorsque
vous installez votre matériel:
■
Suivez tous les avertissements et toutes les
instructions inscrites sur le matériel.
Caution – To prevent extreme operating
temperatures due to reduced airflow
consideration should be made to the amount
of air flow that is required for a safe operation
of the equipment.
■
Assurez-vous que la tension et la fréquence de votre
source d'alimentation correspondent à la tension et à
la fréquence indiquées sur l'étiquette de la tension
électrique nominale du matériel
■
N'introduisez jamais d'objets quels qu'ils soient dans
les ouvertures de l'équipement. Vous pourriez vous
trouver en présence de hautes tensions dangereuses.
Tout objet étranger conducteur risque de produire un
court-circuit pouvant présenter un risque d'incendie
ou de décharge électrique, ou susceptible
Laser Compliance Notice
Sun products that use laser technology comply with Class 1
laser requirements.
d'endommager le matériel.
Symboles
Class 1 Laser Product
Luokan 1 Laserlaite
Klasse 1 Laser Apparat
Laser Klasse 1
Vous trouverez ci-dessous la signification des différents
symboles utilisés:
Attention – Vous risquez d'endommager le
matériel ou de vous blesser. Veuillez suivre les
instructions.
Attention – Surfaces brûlantes. Evitez tout
contact. Les surfaces sont brûlantes. Vous
risquez de vous blesser si vous les touchez.
Appendix C Declaration of Conformity, Regulatory, and Safety Information
Download from Www.Somanuals.com. All Manuals Search And Download.
29
Connexion du cordon d’alimentation
Attention – Tensions dangereuses. Pour
réduire les risques de décharge électrique et
de danger physique, observez les consignes
indiquées.
Attention – Les produits Sun sont conçus
pour fonctionner avec des systèmes
d'alimentation équipés d'un conducteur
neutre relié à la terre (conducteur neutre pour
produits alimentés en CC). Pour réduire les
risques de décharge électrique, ne branchez
jamais les produits Sun sur une source
d'alimentation d'un autre type. Contactez le
gérant de votre bâtiment ou un électricien
agréé si vous avez le moindre doute quant au
type d'alimentation fourni dans votre
bâtiment.
Selon le type d'interrupteur marche/arrêt dont votre
appareil est équipé, l'un des symboles suivants sera utilisé:
Marche – Met le système sous tension
alternative.
Arret – Met le système hors tension
alternative.
Attention – Tous les cordons d'alimentation
ne présentent pas les mêmes caractéristiques
électriques. Les cordons d'alimentation à
usage domestique ne sont pas protégés contre
les surtensions et ne sont pas conçus pour être
utilisés avec des ordinateurs. N'utilisez jamais
de cordon d'alimentation à usage domestique
avec les produits Sun.
Veilleuse – L'interrupteur Marche/Veille
est sur la position de veille.
Modification du matériel
N'apportez aucune modification mécanique ou électrique
au matériel. Sun Microsystems décline toute responsabilité
quant à la non-conformité éventuelle d'un produit Sun
modifié.
L'avertissement suivant s'applique uniquement aux
systèmes équipés d'un interrupteur Veille:
Attention – L'interrupteur d'alimentation
de ce produit fonctionne uniquement comme
un dispositif de mise en veille. Le cordon
d'alimentation constitue le moyen principal de
déconnexion de l'alimentation pour le
système. Assurez-vous de le brancher dans
une prise d'alimentation mise à la terre près
du système et facile d'accès. Ne le branchez
pas lorsque l'alimentation électrique ne se
trouve pas dans le châssis du système.
Positionnement d’un produit Sun
Attention – Evitez d'obstruer ou de
recouvrir les orifices de votre produit Sun.
N'installez jamais un produit Sun près d'un
radiateur ou d'une source de chaleur. Si vous
ne respectez pas ces consignes, votre produit
Sun risque de surchauffer et son
fonctionnement en sera altéré.
L'avertissement suivant s'applique uniquement aux
systèmes équipés de plusieurs cordons d'alimentation:
Niveau de pression acoustique
Le niveau de pression acoustique du lieu de travail définie
par la norme DIN 45 635 Part 1000 doit être au maximum de
70 db(A).
Attention – Pour mettre un système équipé
de plusieurs cordons d'alimentation hors
tension, il est nécessaire de débrancher tous
les cordons d'alimentation.
Conformité SELV
Le niveau de sécurité des connexions E/S est conforme aux
normes SELV.
30
Sun StorEdge PCI/PCI-X Dual Ultra320 SCSI Host Adapter Installation Guide • January 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
Mise en garde relative aux batteries
Attention – Afin d'éviter que le rack ne
penche pendant l'installation du matériel, tirez
la barre anti-basculement du rack.
Attention – Les batteries risquent
d’exploser en cas de manipulation maladroite
ou de remplacement incorrect. Pour les
systèmes dont les batteries sont remplaçables,
effectuez les remplacements uniquement selon
le modèle du fabricant ou un modèle
Attention – Pour éviter des températures de
fonctionnement extrêmes dans le rack,
assurez-vous que la température maximale ne
dépasse pas la fourchette de températures
ambiantes du produit déterminée par le
fabricant.
équivalent recommandé par le fabricant,
conformément aux instructions fournies dans
le manuel de service du système. N’essayez en
aucun cas de démonter les batteries, ni de les
recharger hors du système. Ne les jetez pas au
feu. Mettez-les au rebut selon les instructions
du fabricant et conformément à la législation
locale en vigueur. Notez que sur les cartes
processeur de Sun, une batterie au lithium a
été moulée dans l'horloge temps réel. Les
batteries ne sont pas des pièces remplaçables
par le client.
Attention – Afin d'empêcher des
températures de fonctionnement extrêmes
provoquées par une aération insuffisante,
assurez-vous de fournir une aération
appropriée pour un fonctionnement du
matériel en toute sécurité
Couvercle de l'unité
Avis de conformité des appareils laser
Les produits Sun qui font appel aux technologies lasers sont
conformes aux normes de la classe 1 en la matière.
Pour ajouter des cartes, de la mémoire ou des périphériques
de stockage internes, vous devez retirer le couvercle de
votre système Sun. Remettez le couvercle supérieur en
place avant de mettre votre système sous tension.
Attention – Ne mettez jamais des produits
Sun sous tension si leur couvercle supérieur
n'est pas mis en place. Si vous ne prenez pas
ces précautions, vous risquez de vous blesser
ou d'endommager le système.
Class 1 Laser Product
Luokan 1 Laserlaite
Klasse 1 Laser Apparat
Laser Klasse 1
Mise en garde relative au système en rack
La mise en garde suivante s'applique aux racks et aux
systèmes montés en rack.
Périphériques CD et DVD
L'avertissement suivant s'applique aux périphériques CD,
DVD et autres périphériques optiques:
Attention – Pour des raisons de sécurité, le
matériel doit toujours être chargé du bas vers
le haut. En d'autres termes, vous devez
installer, en premier, le matériel qui doit se
trouver dans la partie la plus inférieure du
rack, puis installer le matériel sur le niveau
suivant, etc.
Attention – L'utilisation de contrôles et de
réglages ou l'application de procédures autres
que ceux spécifiés dans le présent document
peuvent entraîner une exposition à des
radiations dangereuses.
Appendix C Declaration of Conformity, Regulatory, and Safety Information
Download from Www.Somanuals.com. All Manuals Search And Download.
31
Je nach Netzschaltertyp an Ihrem Gerät kann eines der
folgenden Symbole verwendet werden:
Einhaltung sicherheitsbehördlicher
Vorschriften
Lesen Sie vor dem Ausführen von Arbeiten diesen
Abschnitt. Im folgenden Text werden Sicherheitsvor-
kehrungen beschrieben, die Sie bei der Installation eines
Sun Microsystems-Produkts beachten müssen.
Ein – Versorgt das System mit Wechselstrom.
Aus– Unterbricht die Wechselstromzufuhr
zum Gerät.
Sicherheitsvorkehrungen
Treffen Sie zu Ihrem eigenen Schutz bei der Installation des
Geräts die folgenden Sicherheitsvorkehrungen:
Wartezustand – Der Ein-/Standby-Netz-
■
■
Beachten Sie alle auf den Geräten angebrachten
Warnhinweise und Anweisungen.
schalter befindet sich in der Standby-Position.
Stellen Sie sicher, dass Spannung und Frequenz der
Stromversorgung den Nennleistungen auf dem am
Gerät angebrachten Etikett entsprechen.
Modifikationen des Geräts
Nehmen Sie keine elektrischen oder mechanischen
Gerätemodifikationen vor. Sun Microsystems ist für die
Einhaltung der Sicherheitsvorschriften von modifizierten
Sun-Produkten nicht haftbar.
■
Führen Sie niemals Fremdobjekte in die Öffnungen
am Gerät ein. Es können gefährliche Spannungen
anliegen. Leitfähige Fremdobjekte können einen
Kurzschluss verursachen, der einen Brand, Strom-
schlag oder Geräteschaden herbeiführen kann.
Aufstellung von Sun-Geräten
Symbole
Die Symbole in diesem Handbuch haben folgende
Bedeutung:
Achtung – Geräteöffnungen Ihres Sun-
Produkts dürfen nicht blockiert oder
abgedeckt werden. Sun-Geräte sollten niemals
in der Nähe von Heizkörpern oder Heißluft-
klappen aufgestellt werden. Die Nichtbeach-
tung dieser Richtlinien kann Überhitzung
verursachen und die Zuverlässigkeit Ihres
Sun-Geräts beeinträchtigen.
Achtung – Gefahr von Verletzung und
Geräteschaden. Befolgen Sie die Anwei-
sungen.
Achtung – Heiße Oberfläche. Nicht
berühren, da Verletzungsgefahr durch heiße
Oberfläche besteht.
Lautstärke
Gemäß den in DIN 45 635 Teil 1000 definierten Vorschriften
beträgt die arbeitsplatzbedingte Lautstärke dieses Produkts
weniger als 70 dB(A).
Achtung – Gefährliche Spannungen.
Befolgen Sie die Anweisungen, um
Stromschläge und Verletzungen zu vermeiden.
SELV-Konformität
Der Sicherheitsstatus der E/A-Verbindungen entspricht
den SELV-Anforderungen.
32
Sun StorEdge PCI/PCI-X Dual Ultra320 SCSI Host Adapter Installation Guide • January 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
Anschluss des Netzkabels
Warnung bezüglich Batterien
Achtung – Sun-Geräte sind für
Achtung – Bei unsachgemäßer
Handhabung oder nicht fachgerechtem
Austausch der Batterien besteht
Stromversorgungssysteme mit einem
geerdeten neutralen Leiter (geerdeter
Rückleiter bei gleichstrombetriebenen
Geräten) ausgelegt. Um die Gefahr von
Stromschlägen zu vermeiden, schließen Sie
das Gerät niemals an andere Stromversor-
gungssysteme an. Wenden Sie sich an den
zuständigen Gebäudeverwalter oder an einen
qualifizierten Elektriker, wenn Sie nicht sicher
wissen, an welche Art von Stromversor-
gungssystem Ihr Gebäude angeschlossen ist.
Explosionsgefahr. Verwen-den Sie bei
Systemen mit austauschbaren Batterien
ausschließlich Ersatzbatterien desselben Typs
und Herstellers bzw. einen entsprechenden,
vom Hersteller gemäß den Anweisungen im
Service-Handbuch des Produkts empfohlenen
Batterietyp. Versuchen Sie nicht, die Batterien
auszubauen oder außerhalb des Systems
wiederaufzuladen. Werfen Sie die Batterien
nicht ins Feuer. Entsorgen Sie die Batterien
entsprechend den Anweisungen des
Herstellers und den vor Ort geltenden
Vorschriften. CPU-Karten von Sun verfügen
über eine Echtzeituhr mit integrier-ter
Lithiumbatterie. Diese Batterie darf nur von
einem qualifizierten Servicetechniker aus-
gewechselt werden.
Achtung – Nicht alle Netzkabel verfügen
über die gleichen Nennwerte. Herkömmliche,
im Haushalt verwendete Verlängerungskabel
besitzen keinen Überlastschutz und sind
daher für Computersysteme nicht geeignet.
Verwenden Sie bei Ihrem Sun-Produkt keine
Haushalts-Verlängerungskabel.
Gehäuseabdeckung
Die folgende Warnung gilt nur für Geräte mit Standby-
Netzschalter:
Sie müssen die Abdeckung Ihres Sun-Computersystems
entfernen, um Karten, Speicher oder interne Speichergeräte
hinzuzufügen. Bringen Sie vor dem Einschalten des
Systems die Gehäuseabdeckung wieder an.
Achtung – Beim Netzschalter dieses Geräts
handelt es sich nur um einen Ein/Standby-
Schalter. Zum völligen Abtrennen des Systems
von der Stromversorgung dient hauptsächlich
das Netzkabel. Stellen Sie sicher, dass das
Netzkabel an eine frei zugängliche geerdete
Steckdose in der Nähe des Systems ange-
schlossen ist. Schließen Sie das Stromkabel
nicht an, wenn die Stromversorgung vom
Systemchassis entfernt wurde.
Achtung – Nehmen Sie Sun-Geräte nicht
ohne Abdeckung in Betrieb. Die
Nichtbeachtung dieses Warnhinweises kann
Verletzungen oder Geräteschaden zur Folge
haben.
Warnungen bezüglich in Racks eingebauter
Systeme
Die folgenden Warnungen gelten für Racks und in Racks
Die folgende Warnung gilt nur für Geräte mit mehreren
Netzkabeln:
eingebaute Systeme:
Achtung – Bei Produkten mit mehreren
Netz-kabeln müssen alle Netzkabel abgetrennt
wer-den, um das System völlig von der
Stromver-sorgung zu trennen.
Achtung – Aus Sicherheitsgründen sollten
sämtliche Geräte von unten nach oben in
Racks eingebaut werden. Installieren Sie also
zuerst die Geräte, die an der untersten
Appendix C Declaration of Conformity, Regulatory, and Safety Information
Download from Www.Somanuals.com. All Manuals Search And Download.
33
Position im Rack eingebaut werden, gefolgt
von den Systemen, die an nächsthöherer Stelle
eingebaut werden, usw.
Normativas de seguridad
Lea esta sección antes de realizar cualquier operación. En
ella se explican las medidas de seguridad que debe tomar al
instalar un producto de Sun Microsystems.
Achtung – Verwenden Sie beim Einbau den
Kippschutz am Rack, um ein Umkippen zu
vermeiden.
Medidas de seguridad
Para su protección, tome las medidas de seguridad
siguientes durante la instalación del equipo:
■
■
Siga todos los avisos e instrucciones indicados en el
equipo.
Achtung – Um extreme
Betriebstemperaturen im Rack zu vermeiden,
stellen Sie sicher, dass die Maximaltemperatur
die Nennleistung der Umgebungstemperatur
für das Produkt nicht überschreitet
Asegúrese de que el voltaje y frecuencia de la fuente
de alimentación coincidan con el voltaje y frecuencia
indicados en la etiqueta de clasificación eléctrica del
equipo.
■
No introduzca objetos de ningún tipo por las rejillas
del equipo, ya que puede quedar expuesto a voltajes
peligrosos. Los objetos conductores extraños pueden
producir cortocircuitos y, en consecuencia, incendios,
descargas eléctricas o daños en el equipo.
Achtung – Um extreme
Betriebstemperaturen durch verringerte
Luftzirkulation zu vermei-den, sollte die für
den sicheren Betrieb des Geräts erforderliche
Luftzirkulation eingesetzt werden.
Símbolos
En este documento aparecen los siguientes símbolos:
Precaución – Existe el riesgo de que se
produzcan lesiones personales y daños en el
equipo. Siga las instrucciones.
Hinweis zur Laser-Konformität
Sun-Produkte, die die Laser-Technologie verwenden,
entsprechen den Laser-Anforderungen der Klasse 1.
Precaución – Superficie caliente. Evite
todo contacto. Las superficies están calientes y
pueden causar lesiones personales si se tocan.
Class 1 Laser Product
Luokan 1 Laserlaite
Klasse 1 Laser Apparat
Laser Klasse 1
Precaución – Voltaje peligroso. Para
reducir el riesgo de descargas eléctricas y
lesiones personales, siga las instrucciones.
CD- und DVD-Geräte
Die folgende Warnung gilt für CD-, DVD- und andere
optische Geräte:
Achtung – Die hier nicht aufgeführte
Verwendung von Steuerelementen,
Anpassungen oder Ausführung von
Vorgängen kann eine gefährliche
Strahlenbelastung verursachen.
34
Sun StorEdge PCI/PCI-X Dual Ultra320 SCSI Host Adapter Installation Guide • January 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
En función del tipo de interruptor de alimentación del que
disponga el dispositivo, se utilizará uno de los símbolos
siguientes:
Conexión del cable de alimentación
Precaución – Los productos Sun se han
diseñado para funcionar con sistemas de
alimentación que cuenten con un conductor
neutro a tierra (con conexión a tierra de
regreso para los productos con alimentación
de CC). Para reducir el riesgo de descargas
eléctricas, no conecte ningún producto Sun a
otro tipo de sistema de alimentación. Póngase
en contacto con el encargado de las
Encendido – Suministra alimentación de
CA al sistema.
Apagado – Corta la alimentación de CA del
sistema.
instalaciones de su empresa o con un
electricista cualificado en caso de que no esté
seguro del tipo de alimentación del que se
dispone en el edificio.
Espera – El interruptor de
encendido/espera está en la posición de
espera.
Precaución – No todos los cables de
alimentación tienen la misma clasificación
eléctrica. Los alargadores de uso doméstico no
cuentan con protección frente a sobrecargas y
no están diseñados para su utilización con
sistemas informáticos. No utilice alargadores
de uso doméstico con el producto Sun.
Modificaciones en el equipo
No realice modificaciones de tipo mecánico ni eléctrico en el
equipo. Sun Microsystems no se hace responsable del
cumplimiento de normativas en caso de que un producto
Sun se haya modificado.
Colocación de un producto Sun
La siguiente medida solamente se aplica a aquellos
dispositivos que dispongan de un interruptor de
alimentación de espera:
Precaución – No obstruya ni tape las
rejillas del producto Sun. Nunca coloque un
producto Sun cerca de radiadores ni fuentes
de calor. Si no sigue estas indicaciones, el
producto Sun podría sobrecalentarse y la
fiabilidad de su funcionamiento se vería
afectada.
Precaución – El interruptor de
alimentación de este producto funciona
solamente como un dispositivo de espera. El
cable de alimentación hace las veces de
dispositivo de desconexión principal del
sistema. Asegúrese de que conecta el cable de
alimentación a una toma de tierra situada
cerca del sistema y de fácil acceso. No conecte
el cable de alimentación si la unidad de
alimentación no se encuentra en el bastidor
del sistema.
Nivel de ruido
De conformidad con los requisitos establecidos en el
apartado 1000 de la norma DIN 45635, el nivel de ruido en
el lugar de trabajo producido por este producto es menor de
70 db(A).
Cumplimiento de la normativa para
instalaciones SELV
Las condiciones de seguridad de las conexiones de entrada
y salida cumplen los requisitos para instalaciones SELV (del
inglés Safe Extra Low Voltage, voltaje bajo y seguro).
Appendix C Declaration of Conformity, Regulatory, and Safety Information
Download from Www.Somanuals.com. All Manuals Search And Download.
35
La siguiente medida solamente se aplica a aquellos
dispositivos que dispongan de varios cables de
alimentación:
Advertencia sobre el sistema en bastidor
Las advertencias siguientes se aplican a los sistemas
montados en bastidor y a los propios bastidores.
Precaución – En los productos que
cuentan con varios cables de alimentación,
debe desconectar todos los cables de
alimentación para cortar por completo la
alimentación eléctrica del sistema.
Precaución – Por seguridad, siempre
deben montarse los equipos de abajo arriba. A
saber, primero debe instalarse el equipo que se
situará en el bastidor inferior; a continuación,
el que se situará en el siguiente nivel, etc.
Advertencia sobre las baterías
Precaución – Para evitar que el bastidor se
vuelque durante la instalación del equipo,
debe extenderse la barra antivolcado del
bastidor.
Precaución – Si las baterías no se
manipulan o reemplazan correctamente, se
corre el riesgo de que estallen. En los sistemas
que cuentan con baterías reemplazables,
reemplácelas sólo con baterías del mismo
fabricante y el mismo tipo, o un tipo
Precaución – Para evitar que se alcance
una temperatura de funcionamiento extrema
en el bastidor, asegúrese de que la
temperatura máxima no sea superior a la
temperatura ambiente establecida como
adecuada para el producto.
equivalente recomendado por el fabricante, de
acuerdo con las instrucciones descritas en el
manual de servicio del producto. No
desmonte las baterías ni intente recargarlas
fuera del sistema. No intente deshacerse de las
baterías echándolas al fuego. Deshágase de las
baterías correctamente de acuerdo con las
instrucciones del fabricante y las normas
locales. Tenga en cuenta que en las placas CPU
de Sun, hay una batería de litio incorporada
en el reloj en tiempo real. Los usuarios no
deben reemplazar este tipo de baterías.
Precaución – Para evitar que se alcance
una temperatura de funcionamiento extrema
debido a una circulación de aire reducida,
debe considerarse la magnitud de la
circulación de aire requerida para que el
equipo funcione de forma segura.
Cubierta de la unidad del sistema
Aviso de cumplimiento de la normativa para
la utilización de láser
Los productos Sun que utilizan tecnología láser cumplen los
Debe extraer la cubierta de la unidad del sistema
informático Sun para instalar tarjetas, memoria o
dispositivos de almacenamiento internos. Vuelva a colocar
la cubierta antes de encender el sistema informático.
requisitos establecidos para los productos láser de clase 1.
Precaución – No ponga en funcionamiento
los productos Sun que no tengan colocada la
cubierta. De lo contrario, puede sufrir lesiones
personales y ocasionar daños en el sistema.
Class 1 Laser Product
Luokan 1 Laserlaite
Klasse 1 Laser Apparat
Laser Klasse 1
36
Sun StorEdge PCI/PCI-X Dual Ultra320 SCSI Host Adapter Installation Guide • January 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
Dispositivos de CD y DVD
La siguiente medida se aplica a los dispositivos de CD y
DVD, así como a otros dispositivos ópticos:
Precaución – La utilización de controles,
ajustes o procedimientos distintos a los aquí
especificados puede dar lugar a niveles de
radiación peligrosos.
Nordic Lithium Battery Cautions
Norge
Advarsel – Litiumbatteri —
Eksplosjonsfare. Ved utskifting benyttes kun
batteri som anbefalt av apparatfabrikanten.
Brukt batteri returneres apparatleverandøren.
Sverige
Varning – Explosionsfara vid felaktigt
batteribyte. Använd samma batterityp eller en
ekvivalent typ som rekommenderas av
apparattillverkaren. Kassera använt batteri
enligt fabrikantens instruktion.
Danmark
Advarsel! – Litiumbatteri —
Eksplosionsfare ved fejlagtig håndtering.
Udskiftning må kun ske med batteri af samme
fabrikat og type. Levér det brugte batteri
tilbage til leverandøren.
Suomi
Varoitus – Paristo voi räjähtää, jos se on
virheellisesti asennettu. Vaihda paristo
ainoastaan laitevalmistajan suosittelemaan
tyyppiin. Hävitä käytetty paristo valmistajan
ohjeiden mukaisesti.
Appendix C Declaration of Conformity, Regulatory, and Safety Information
Download from Www.Somanuals.com. All Manuals Search And Download.
37
38
Sun StorEdge PCI/PCI-X Dual Ultra320 SCSI Host Adapter Installation Guide • January 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
|