Summit Refrigerator SPR7OS User Manual

Felix Storch, Inc.  
SUMMIT PROFESSIONAL DIV.®  
USE AND CARE GUIDE  
BUILT-IN UNDER-COUNTER REFRIGERATORS  
BUILT-IN UNDER-COUNTER FREEZERS  
BUILT-IN WINE CELLARS  
OUTDOOR REFRIGERATORS AND FREEZERS  
INDOOR DRAWER REFRIGERATORS AND FREEZERS  
OUTDOOR DRAWER REFRIGERATORS AND FREEZERS  
AUTO-DEFROST BI605FF SERIES  
SPR7OS SERIES  
SCFF55 SERIES  
SCR600LOS SERIES  
SP6DSSTBOS SERIES  
SP6DS2DOS SERIES  
SPR601OS SERIES  
BI540 / BI541 SERIES  
BI605FF SERIES  
CT66BI / CT67BI SERIES  
SWC6GBI SERIES  
FF6BI & FF7BI SERIES  
FS62BI SERIES  
SP6 DRAWER SERIES  
SCR600BI-SERIES  
SPF5DSSTB  
ALB651 / ALB653B SERIES  
ALB751 / ALB753B SERIES  
OUTDOOR REFRIGERATORS  
If you need service or call with a question, please have this information ready. We  
advise you to keep this Owners Manual in your possession.  
Model:  
Options added:  
Serial number:  
Date of Purchase ______________________ Where Purchased___________________  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Felix Storch, Inc.  
SUMMIT PROFESSIONAL DIV.  
Page 3  
INSTALLATION INSTRUCTIONS  
UNPACKING  
Excessive Weight Hazard! * Use two or more people to move and install your appliance.  
Failure to do so can result in back or other injury.  
ALLOW APPLIANCE TO SIT UPRIGHT FOR 24 HOURS BEFORE TURNING ON, TO ALLOW THE  
COMPRESSOR LUBRICANT TO DRAIN.  
1. Remove Packaging Materials  
2. Remove tape and glue residue from surfaces before turning on the appliance. Rub a small  
amount of liquid dish soap over the adhesive with your fingers. Rinse with warm water and dry.  
3. Do not use sharp instruments, rubbing alcohol, flammable fluids, or abrasive cleaners to  
remove tape or glue. These products can damage the surface of your appliance.  
4. When Moving Your Appliance:  
Your appliance is heavy. When moving the appliance for cleaning or service, be sure to protect  
the floor. Always pull the appliance straight out when moving it. Do not wiggle or “walk” the  
appliance when trying to move it, because floor damage can occur.  
5. Clean Before Using  
After you remove all of the packaging materials, clean the inside of your appliance before using  
it. See the cleaning instructions in “Appliance Care.”  
6. All upright models have level legs in the front and many also have them in the rear. Level as  
necessary for best operation.  
7. If your appliance has casters, after moving into place, lock the brakes on those casters  
supplied with brakes. Always unlock before moving the appliance for cleaning.  
Keep flammable materials and vapors, such as gasoline, away from appliances. Failure to do so can result in  
explosion, or fire.  
LOCATION REQUIREMENTS  
IMPORTANT: Do not install the appliance near an oven, radiator, or other heat source, nor in a  
location where the temperature will fall below 45°F (7°C). Do not place in direct sunlight.  
Check the strength of the floor before installing your appliance. It should hold the weight of a  
fully loaded appliance. Allow at least 1” (2.5 cm) of airspace at the top and on both sides of the  
appliance and 1” (2.5 cm) between the back of the appliance and the wall. If the appliance is  
going to be placed against a wall, if possible, leave extra space on the hinge side so the door can  
open wider than its width (to make it easier to remove shelves or storage bins).  
NOTE: This appliance may be installed side by side with another appliance. Allow for a 3’’ (7.5  
cm) clearance at the top and sides, and a ¼” (0.64 cm) clearance between the appliances.  
IF YOUR MODEL HAS THE LETTERS “BI” IN THE MODEL NUMBER OR SUFFIX, OR BEGINS WITH “ALB”, IT  
IS DESIGNED FOR BUILT IN USE, AND DOES NOT REQUIRE CLEARANCE EXCEPT IN THE BACK. BE SURE  
THAT YOU DO NOT BLOCK THE AIRFLOW UNDER THE APPLIANCE .  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Felix Storch, Inc.  
Page 4  
SUMMIT PROFESSIONAL DIV.  
INSTALLATION INSTRUCTIONS  
CHOOSING THE RIGHT PLACE  
Place the appliance in a dry and regularly ventilated place. It is recommended that this appliance always be operated in an  
ambient temperature of at least 60°F and under 85°F. The appliance may be exposed to lower or higher temperatures but only for a  
short period of time and the temperature should never be lower than 45°F. Never place the appliance near heat emitting devices  
(e.g. cooker, radiator, water heater or similar devices) and do not expose it to direct sunlight.  
RECOMMENDED GROUNDING METHOD  
A 115 Volt, 60 Hz. AC only 15- or 20- amp fused or circuit breaker, grounded electrical supply is required. It is recommended that a  
separate circuit serving only your appliance be provided. Use outlets that cannot be turned off by a switch or pull chain. Connect  
this appliance to a 3 prong power supply socket outlet (which has a ground terminal). If you only have a two prong outlet have it  
replaced by a qualified technician with an outlet that meets the local codes. DO NOT USE AN EXTENSION CORD. Required  
nominal voltage and frequency are indicated on the rating plate. The connection to the power supply and grounding has to be  
made according to current standards and regulations. The appliance resists temporary voltage tolerance from -15 to 10%.  
ON OUTDOOR MODELS ONLY  
Electrical Shock Hazard. Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter.  
Do not use an extension cord. Failure to follow these instructions can result in fire or electrical shock.  
Many outdoor outlets are controlled by wall switches. Turning off power and on again may cause the GFCI switch to trip.  
A GFCI (ground fault circuit interrupter) is built into every line cord. Do not defeat or bypass this important safety feature. The line  
cord supplied with this appliance is specially designed for outdoor use. Use only a factory supplied replacement cord with a GFCI  
(ground fault circuit interrupter) in the event the cord becomes damaged.  
You may purchase these cords from either our sales or service department at 718-893-3900 (sales) or 718-328-8700 (service).  
It can also be ordered online from www.summitapplianceparts.com  
ENERGY SAVING TIPS  
The more airflow you can provide around an appliance, the less energy it will use.  
If your appliance needs defrosting, keep ice build-up to less than 1/2 inch.  
Keep doors or drawers open a minimum of time, and shut securely.  
LEVELING YOUR APPLIANCE  
1. Locate the two front leveling legs taped among the packing materials. In most models these legs are already mounted into the  
underside of the appliance.  
2. Screw these legs into the front holes on the bottom of the appliance. The back of the appliance rests on two fixed supports.  
(Built-in models also have rear level legs that can provide more precise leveling).  
3. Adjust the front legs just enough to lift the cabinet up off of the floor.  
4. Place a leveling tool on top of the appliance: first side to side, then front to back. Turn leg counterclockwise to raise a corner.  
Turn leg clockwise to lower a corner.  
5. Repeat Step 4 until appliance is level.  
6. After appliance is fully loaded, recheck with level as in Step 4.  
7. If your appliance is equipped with casters, the two front casters have brakes to prevent rolling. Keep brakes locked, and unlock  
for moving only.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Felix Storch, Inc.  
Page 5  
SUMMIT PROFESSIONAL DIV.  
APPLIANCE USE  
In order to ensure proper temperature, you need to permit proper airflow in the appliance. Do not block any air  
vents. If the vents are blocked, airflow will be prevented, and temperature and moisture problems may occur.  
Always position contents to allow some airflow between shelves or baskets.  
Allow the appliance to cool at least 6 to 8 hours before adding contents. Allow 24 hours for temperature to  
stabilize.  
NOTE: When the appliance is first started, the compressor will run constantly until the appliance is cold, It may  
take up to 6 or 8 hours (or longer), depending on room temperature and the number of times the appliance door is  
opened. After the appliance is cooled, the compressor will turn on and off as needed to keep the appliance at the  
proper temperature.  
The outside of your appliance may feel warm. This is normal. The appliance’s design and main function is to  
remove heat from packages and air space inside the appliance. The heat is transferred to the room air, making the  
outside of the appliance feel warm. In some models the condenser that gets warm is inside the side walls, making  
these walls warm to the touch.  
REVERSING THE DOOR SWING (Selected models)  
If you find the direction of opening the door on your appliance inconvenient, on some models you can change it.  
Holes on the opposite side have already been prepared in the factory. On models with our wrapped stainless steel  
door and 12 inch pro handle, (suffix SSTB, SSVH or CSS or with optional handles “TB” or “SH” ) you must order  
these with either a right hand or left hand door swing in advance. These doors cannot be reversed. Models with a  
suffix SSHH, BIFR, BIIF, and CSSHH can be reversed.  
TO REVERSE YOUR DOOR  
Take off the upper hinge cover from the door and remove the screws that hold the top hinge.  
Lift the hinge straight up to free the hinge pin from the socket in the top of the door.  
Lift the door up away to free its bottom socket from the hinge pin.  
Remove the screws to the bottom hinge.  
Remove the decorative caps from opposite side and plug the holes from original side with the decorative caps.  
Move the bottom hinge to the opposite side and tighten the screws. Use any lock washers or nuts if they were  
installed in the original installation.  
Replace door onto the hinge pin on the bottom hinge. Place top hinge pin into door. Insert screws into the top  
hinge and tighten.  
If you notice the door not hanging straight—loosen the top hinges, adjust the door until it is level and tighten the  
screws.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Felix Storch, Inc.  
SUMMIT PROFESSIONAL DIV.  
Page 6  
APPLIANCE OPERATION  
Base Grill (some models only)  
To Remove and Replace the Base Grill:  
1. Open the appliance door and remove the base grill by pulling down and out from the top.  
2. Replace the base grill by putting the clips in the openings in the appliance panel. Push in until the base grill snaps into place.  
An optional stainless steel grill is available for some models (Models beginning with FF6, FF7, CT66, CT67, SCR600, FS62,  
Changing the light bulb (some models only)  
NOTE: Not all appliance bulbs will fit your appliance. Be sure to replace the bulb with one of the same size, shape, base size  
and wattage. You can purchase bulbs from www.summitapplianceparts.com  
1. Unplug appliance or disconnect power.  
2. Remove the light shield. Most models do not require tools.  
3. Replace the light bulb with an appliance bulb of the same wattage.  
4. Replace the light shield.  
5. Plug in appliance or reconnect power.  
Loss of Power  
After the power is restored, unplug the appliance for 30 minutes, to allow the refrigeration system to equalize. During this time  
keep the door closed whenever possible.  
REMEMBER: A full appliance stays cold longer than a partially filled one.  
Moving Care  
1. Remove all containers.  
2. Unplug the appliance.  
3. Clean it thoroughly.  
4. Tape the appliance shut and tape the electrical cord to the cabinet.  
When you get to your new location, refer to the “Installation Instructions” and “Appliance Use” sections for informa-  
tion on installation and setting the controls.  
Removal / Replacing of the Drawers on the SP6DS, SP6DSSTB or SP6DS2D models  
To remove the drawers from the refrigerator these directions need to be followed:  
Pull the drawer out towards you completely.  
On both sides of the drawer there are stainless steel slides.  
On each slide there is a black lever.  
The left lever should be pulled up.  
The right lever should be pulled down. Both levers should be pulled at the same time while continuing to pull the drawer.  
To re-install the drawers on the appliance:  
Just simply line up the hinges on the drawer and the hinges on the appliance and gently push the drawer in. Once lined up close  
the drawer completely then open again to make sure the drawer is on track.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Felix Storch, Inc.  
Page 7  
SUMMIT PROFESSIONAL DIV.  
APPLIANCE CARE  
Cleaning Your Frost-Free Refrigerator  
Use nonflammable cleaners.  
Frost-free means that you do not have to defrost your appliance. Frost is removed by air moving and collecting any moisture  
and depositing it on the cooling coil. The cooling coil periodically warms up enough to melt the frost, and the water then flows  
down to the drain pan (located behind the base grill) where it is evaporated.  
Complete cleaning should be done at least once a year.  
1. Unplug appliance or disconnect power.  
2. Remove all substances.  
3. Wash the inside walls with a solution of mild detergent in warm water or 2 tbs (26 mg) baking soda to 1 qt (0.95 L) warm  
water.  
• Do not use abrasive or harsh cleaners such as window sprays, scouring cleansers, flammable fluids, cleaning waxes,  
concentrated detergents, bleaches or cleansers containing petroleum products on plastic parts, interior and door liners or  
gaskets. Do not use paper towels, scouring pads, or other harsh cleaning tools. These can scratch or damage materials.  
4. Rinse well and wipe dry with a clean soft cloth.  
5. Use the appropriate cleaning method for your exterior finish.  
Painted metal: Wash exteriors with a clean sponge or soft cloth and a mild detergent in warm water. Do not use abrasive or  
harsh cleaners, or cleaners designed for stainless steel. Dry thoroughly with a soft cloth. For additional protection against  
damage to painted metal exteriors, apply appliance wax (or auto paste wax) with a clean, soft cloth. Do not wax plastic parts.  
6. Plug in appliance or reconnect power.  
7. Replace all containers.  
Stainless steel: Clean stainless steel with special stainless steel cleaners only. Do not use bleach or any abrasive cleaners.  
Cleaning your cycle defrost or manual defrost refrigerator  
Cycle defrost models utilize a system, where ice builds up on the rear wall and melts when the compressor is off. Manual  
defrost models continually build ice on inner walls.  
NEVER USE A METAL OBJECT TO REMOVE ICE FROM THE REAR WALL. IF NEEDED, USE A PLASTIC ICE-  
SCRAPER OR A HAIR DRYER.  
Clean surfaces, using the same instructions as for frost-free models.  
For CSS Models (completely stainless steel) or models with stainless steel doors and  
handles; please use only cleaners especially made for stainless steel.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Felix Storch, Inc.  
Page 8  
SUMMIT PROFESSIONAL DIV.  
TEMPERATURE SELECTION  
YOUR APPLIANCE MAY HAVE A MECHANICAL (DIAL) OR DIGITAL THERMOSTAT.  
INSTRUCTIONS FOR BOTH FOLLOW:  
MECHANICAL THERMOSTAT INSTRUCTIONS  
The refrigerator is controlled with a thermostat knob located inside the unit, towards the upper right-hand corner. Turn the knob clockwise from the  
STOP (0) position toward the higher numbers for colder temperatures.  
Temperature Controls  
•Higher settings on the knob (higher numbers) mean lower temperatures (colder) in all compartments of the appliance.  
On the coldest settings temperatures in some spots of the interior of the appliance may even drop below 32°F. Use  
higher thermostat settings only when required or recommended. When the ambient temperature is normal, we  
recommend the medium setting.  
•Changes of the ambient temperature affect temperature in the interior of the appliance so choose a correct setting of the  
thermostat knob, depending on your ambient conditions.  
•In the STOP (0) position the appliance does not operate (the cooling system is switched off), yet power supply is not interrupted (the light is on, when  
you open the refrigerator door).  
•The temperature in the refrigerator and in the freezer compartment also depend on how often you open the door.  
- In all small refrigerators and freezers without interior fans, temperatures are coldest near the bottom, and occasionally near the rear. Place contents  
accordingly. It is best not to operate these units mostly empty. If temperatures are erratic, try putting some water bottles or freezer packs inside  
to create a load for the compressor.  
DIGITAL THERMOSTAT INSTRUCTIONS  
If you find that it is necessary to change the temperature setting for your digital thermostat controlled appliance, please refer to the  
following instructions. The front panel of the thermostat is illustrated here:  
melting snowflake  
snowflake  
Up & Down arrows  
To see the SETPOINT:  
Push and immediately release the SET key -the display will show the SET point value. Wait 5 seconds and the probe value will  
display again.  
To change the SETPOINT:  
Push and hold the SET key for more then 3 seconds to change the set point value; The value of the set point will be displayed, and  
the “snowflake” LED will start blinking.  
To change the SET value:  
Push the up or down arrows to the desired setting; the new setting will be memorized after 15 seconds, provided no other  
keys are pushed.  
Note: The minimum and maximum range of your thermostat is preset and locked by us; so it cannot easily be accidentally moved  
between freezer and refrigerator temperatures. To reset this range lock, either call us or find information on our website under  
troubleshooting.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Felix Storch, Inc.  
Page 9  
SUMMIT PROFESSIONAL DIV.  
KEYPAD LOCK (optional on most models)  
Factory set default password: The factory set default password is 0123. If the default password is lost,  
press the key (located inside the battery box) for 30 seconds then wait for the warning sound which  
signifies the factory set default password has been restored.  
To set the password: While door is open press the  
key (located inside the battery box) until it jingles,  
enter the 0123 password then # within 10 seconds to confirm. Enter the password (1-16 digits) then press #  
again to confirm. A total of 10 passwords can be set. Note: each password starts from the number 0 to 9 in order. The first  
password starting with 0 is the default password. For example, use 1xxx, then 2xxx etc. for 10 users.  
Changing password: While the door is open, press the  
key (located inside the battery box) until it jingles, enter the old  
password and press # within 10 seconds to confirm. Enter new password then press # to confirm. Note: the first digit cannot be  
changed.  
To open the door: While the door is closed, press the  
key, enter the password then press  
again to confirm.  
To lock door manually: Press #.  
Function setting of automatic lock: To set the auto-lock to lock on a preset time interval press the  
key (inside the battery  
box); enter a number (the time interval in seconds from 10-99) then press # to confirm. The auto-lock time can be set between  
10-99 seconds after opening the door. If the time is set less than 10 seconds, the door will not lock automatically, only manually.  
Deleting the door-opening passwords: Press the  
key, enter default password followed by 0000, then press # and all the  
door-opening passwords will be deleted except for the default password.  
Note: To access the battery box you need to remove only the two small screws, on the top and bottom of that cover. Do not  
remove the 4 screws holding the keypad and cover to the appliance door.  
IF YOUR MODEL HAS A FRONT LOCK (SELECTED MODELS)  
Your lock has a feature called automatic key eject. To lock or unlock the appliance, you must push and hold the key in the lock  
while turning. The lock is spring loaded, so the key cannot be left in the lock.  
If the key is lost, contact your dealer or SUMMIT APPLIANCE to purchase a replacement. Always give the model and serial  
number of your appliance when requesting a replacement key. Keys for most models can be ordered online at  
NEVER KEEP KEYS WITHIN THE REACH OF CHILDREN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Felix Storch, Inc.  
Page 10  
SUMMIT PROFESSIONAL DIV.  
ALARM INSTRUCTIONS (alarms are optional on most models)  
SETTING THE HIGH/LOW ALARM  
1. Press the MODE button until unit is in the ALARM DISPLAY MODE indicated by the display of  
current temperature and HI and LO alarm settings.  
2. To set the HIGH temperature alarm limit press the HI button, to advance the display in 1° incre-  
ments, until the desired high temperature is displayed. Press and hold the HI button to rapidly ad-  
vance the display in 5° increments.  
3. To set the LOW temperature alarm limit press the LO button, to advance the display in 1° incre-  
ments, until the desired low temperature is displayed. Press and hold the LO button to rapidly ad-  
vance the display in 5° increments.  
ALARM  
The unit will sound the alarm in both NORMAL DISPLAY MODE and ALARM DISPLAY MODE  
DISPLAY MODE. Slide the ALARM ON/OFF switch to ON. When the current temperature display rises above the HI set point, or falls  
below the LO set point, the alarm will sound for 1 minute and issue a 3 second repeater beep every minute thereafter, for up to 12 hours.  
The alarm will continue to sound even if the current temperature display returns to an “in range” condition.  
To temporarily silence the alarm press either the HI or LO button on the back of the unit. The unit is still active and the alarm will sound  
again if the temperature goes out of range. To permanently silence the alarm, slide the ALARM ON/OFF switch to OFF position.  
OPERATION MODES  
SUMMIT alarms have two operating modes: NORMAL AND DISPLAY  
DISPLAY MODE and ALARM DISPLAY MODE. To change from one mode to another press the MODE button once.  
NORMAL DISPLAY MODE - is indicated by the display of current temperature and the MIN (minimum) and MAX (maximum) tempera-  
tures. These temperatures relate to external (probe) temperature if the probe is plugged in, and to ambient temperature if the sensor  
probe is removed.  
ALARM DISPLAY MODE - is indicated by the display of current temperature and the HI and LO alarm settings. These temperatures re-  
late to external (probe) temperature if the probe is plugged in, and to ambient temperature if the sensor probe is removed.  
RESETTING THE UNIT  
Use a pointed object to push the RESET button on the back of the unit. It is necessary to reset the unit whenever a change is made to  
°C/°F temperature, FAST/NORMAL sampling rate, or the probe sensor is plugged in or removed.  
NOTE: HI/LO temperature alarm settings and MIN/MAX memories will be cleared after resetting the unit.  
SELECTING THE SAMPLING RATE  
To select normal sampling rate (60 seconds) or fast sampling rate (10 seconds) slide the switch on back of unit to NORMAL or FAST  
NOTE: The unit must be reset after changing the sampling rate. Using the NORMAL sampling rate will extend battery life.  
RESETTING MIN/MAX MEMORIES  
There are two ways to reset the memories:  
I. To reset both minimum and maximum memories - press MEMORY CLEAR button. 2. To reset individual minimum and maximum  
memories - press either the MIN or MAX button (on back of unit) once to reset the respective memory. The other memory will remain un-  
affected. NOTE: You must be in Normal Display Mode to reset the memories.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Felix Storch, Inc.  
Page 11  
SUMMIT PROFESSIONAL DIV.  
INSTRUCTIONS FOR INTREGRATED FRAME (SUFFIX ’IF’) FOR BUILT-IN APPLICATIONS  
Note: The directions below are for installation under a cabinet in a 24 inch cutout space. If you will be using this product in a freestanding  
application, please skip below, and begin with step A1 in lower half of page.  
1) Remove door from chassis by unscrewing 3 screws in top hinge and 2  
screws in bottom hinge. Keep screws, discard hinges.  
2) Remove top and bottom hinge bushings.  
3) Remove frame from door.  
4) Attach customer supplied handle to door panel using countersunk  
screws.  
5) Screw door panel to frame using 14 screws.  
6) Slide frame over refrigerator door and attach with 1 screw on each  
side on center of door.  
7) Attach top brace to frame with 1 screw on each side. Attach bottom  
brace in the same manner.  
8) Drill a hole through the top and bottom panel using the braces as a  
guide with a 1/8” drill bit. Install screws to finish attaching the top and  
bottom braces securely to the frame.  
9) Drill a hole into the door panel from the top and bottom using the braces as a guide with 1/4” drill bit. Do not exceed 5/8” deep. This is  
the hole that the door will pivot on.  
10) Remount the door using the supplied top and bottom hinges.  
INSTRUCTIONS FOR INTREGRATED FRAME (SUFFIX ’IF’) FOR FREESTANDING USE  
A1) Remove door from chassis by unscrewing 3 screws in top hinge and 2  
screws in bottom hinge. Keep screws, discard hinges.  
A2) Remove top and bottom hinge bushings.  
A3) Remove frame from door.  
A4) Attach customer supplied handle to door panel using countersunk  
screws.  
A5) Screw door panel to frame using 14 screws.  
A6) Slide frame over refrigerator door and attach with 3 screw on each side  
A7) Install top and bottom hinge bushings.  
A8) Remount the door using the supplied top and bottom hinges.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Felix Storch, Inc.  
Page 12  
SUMMIT PROFESSIONAL DIV.  
APPLIANCE OPERATION  
FF6BI - FF7BI – SCR600LOS – SPR7OS- SPR601OS – SCR600BI - SWC6GBI - ALB751— ALB753B Series  
DEFROST SYSTEM, OPERATION AND SHELF ADJUSTMENT - All models of the above series are all-refrigerators, with no  
freezer compartment and an auto-defrost system. During the compressor operation, ice will build along the rear cold wall (the  
evaporator plate is behind the wall). During the compressor’s off-cycle, ice will melt, drip down, collect in the trough at the bottom  
and drain through the small hole into a tray above the compressor; where the compressor’s heat will evaporate the water. If you  
notice excessive ice build-up on the rear wall, try setting the thermostat to a slightly warmer setting; be sure that the gasket is  
sealing well – that there is no obstruction of the drain hole in the bottom rear of these units. Models with black cabinets include  
glass shelves. These shelves stop short an inch before the back wall, which is essential for air flow and the automatic defrost  
system. Do not block with food or containers. All models have removable easily adjustable shelves. To remove a shelf, simply lift  
the rear of the shelf out of its locking position and slide the shelves forward. Replace shelves the same way, being sure they lock  
into place. The thermostat of these units is located on the right hand side top, as you face the refrigerator. Turn clockwise for colder  
operation, and counter clockwise to save energy and increase the temperature. The light on the FF6BI models is controlled by an  
automatic plunger switch whenever the door is opened. Models with glass doors and flat door liners have a rocker switch to  
manually turn the light on or off. The light should be kept off when the door is closed to save energy and help keep interior  
temperatures lower.  
BI540 – BI541 – CT67BI - ALB651—ALB653B - CT66BI—CT66B Series  
DEFROST SYSTEM, OPERATION AND SHELF ADJUSTMENT - Models above are refrigerator-freezer combinations with a  
manual defrost freezer section and an automatic defrost fresh-food section. When ice builds to ½ inch around the freezer; empty  
the contents of the whole unit and defrost carefully (DO NOT USE SHARP OBJECTS) following directions earlier in this manual.  
The fresh food section will defrost itself, exactly like the models in the previous section. The freezer in this unit is rated four stars,  
which makes it suitable for ice-cream and short term storage of meats and other perishable items. For best storage, be sure not to  
over-pack and assure the freezer door closes fully. Shelves adjust the same as the section above. Models with black cabinets as  
well as CT67BI models include glass shelves. These shelves stop short an inch before the back wall, which is essential for air flow  
and the automatic defrost system. Do not block with food or containers. The thermostat of these units is located on the right hand  
side, top, as you face the refrigerator. Turn clockwise for colder operation, and counter clockwise to save energy and increase the  
temperature. Lights on these units are all controlled by an automatic plunger type switch.  
SCFF55 Series  
These units are frost-free freezers with a fan cooled interior. The cooling is provided by the evaporator module mounted to the top  
of the unit. Air is circulated through the fan grill at the front of the unit and an outlet at the rear of the unit. Try to keep the air path as  
free as possible for optimal performance. No defrosting of these units is normally needed. There are no user serviceable parts  
within the evaporator module, so do not tamper or attempt to move this part. It is part of the sealed refrigeration system. Models  
with black cabinets include glass shelves. These shelves stop short an inch before the back wall, which is essential for air flow. Do  
not block with food or containers All models have removable easily adjustable shelves. To remove a shelf, simply lift the rear of the  
shelf out of its locking position and slide the shelves forward. Replace shelves the same way, being sure they lock into place. The  
light in the SCFF55 models is controlled by a manual rocker switch. Keep the light off when the door is closed for better  
performance and to save energy. Models with ice-makers installed do not include an interior light.  
SWC6GBI Series Wine Cellars  
These wine cellars are fully automatic defrost (see description of the defrost system under Model FF6BI series). There is a light in  
the upper right corner, controlled by a rocker switch. Base models of the SWC6G series have chrome plated shelves, while some  
models are equipped with optional flat wire shelves or wooden shelves. For maximum capacity, it is possible to lay wine bottles at  
the rear of the shelves cross-wise, behind the bottles facing forward. Keep one inch of clearance behind the shelves and the rear  
wall for air circulation and the defrost system. Glass doors should be cleaned with non-abrasive glass cleaners, and it is  
recommended that the interiors be cleaned with only a baking soda –water- mix so odors are not left behind that can be absorbed  
by corks. These models are one temperature zone only, although the lower shelves are normally a few degrees colder than the  
upper shelves.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Felix Storch, Inc.  
Page 13  
SUMMIT PROFESSIONAL DIV.  
APPLIANCE OPERATION  
BI605FF Series  
These refrigerator-freezers are fully automatic defrost refrigerator-freezers. They utilize a digital thermostat with a built-in  
defrost-timer (mounted in the kick-plate) to intermittently turn off the refrigeration system long enough for the freezer plate to  
melt accumulated ice. The melted water is drained out of the appliance through the metal tray below the freezer compartment to  
a plastic tray above the compressor where the water is evaporated. During the cooling cycles, it is normal to see a small ice  
accumulation on the freezer floor. Be sure to keep the path for water removal clear, and the metal tray properly seated. The  
digital thermostat will display “DEF” during the defrost function.  
The auto-defrost feature adds convenience, but it is not recommended for uses where critical medicine, pharmaceuticals or  
vaccines need to be kept frozen. A manual or frost-free freezer compartment or a separate freezer is more suitable for these  
applications. SUMMIT has a full range of such products.  
To set the interior temperature, (it should be set only for the fresh food section) follow the instructions for digital thermostats.  
Model BI605FF does not include a vegetable crisper as a standard feature.  
FS62BI Series  
These freezers are manual defrost, commercial freezers capable of operating at -25°C (-13°F). Follow the defrosting  
instructions found earlier in the booklet; being careful not to use sharp objects to scrape the ice. The cooling coils (part of the  
sealed refrigeration system) run through each fixed shelf. The drawers are fully removable, and you can operate the freezer  
without them if desired. However, the drawers contribute to energy efficiency and are best used whenever possible. The  
thermostat is located on the exterior front of the unit in the face of the tabletop. In some cases, on models with the CSS suffix, or  
models modified for ADA applications, the thermostat is housed on the rear of the unit, near the top. It is convenient to set it  
prior to installing (many customers will be satisfied with a warmer set-point, which is still colder than many household freezers).  
Shelf positions in FS62BI models are fixed in position.  
OUTDOOR REFRIGERATORS  
(BRANDED SUMMIT OR OTHER BRANDS)  
(SPR7OS Series, SPR7OSBI series, SPR601OS Series, SCR600LOS Series and Drawer series)  
Models for outdoor use all contain the same internal defrost system as the FF7BI series on the prior pages. Your unit may have  
a light controlled by a rocker switch, an automatic switch or no light. (Drawer units are not equipped with lights). Read directions  
earlier in this booklet, specifically on the use of GFCI outdoor cord, location requirements, tip-over brackets for drawer units,  
drawer removal and replacement and safety. These refrigerators are not designed to operate when exterior temperatures are  
below 45 degrees F. If you have seasons with temperatures routinely that low, these units should be unplugged, cleaned and  
stored for the winter. Always leave the door slightly ajar during storage so odors will not build-up inside the units. Once a  
season, when foods are not present, (prior to winter storage is ideal) the stainless steel exterior of the units can be lightly coated  
with WD-40 to restore the luster and protect the finish. A vinyl cover for the SPR7-OS series can be ordered from your dealer, or  
from www.summitapplianceparts.com. Drawer refrigerators and SPR7-OSBI models are suitable for under-counter or built-in  
applications. SPR7-OS models, and SCR600LOS series and SPR601OS series are intended for free-standing use, and if put  
under a counter, provisions for adequate air flow must be provided (minimum 1 inch on sides and top and 2 inches in the rear).  
FOR BEST PERFORMANCE OF OUTDOOR REFRIGERATORS;  
KEEP OUT OF DIRECT SUNLIGHT  
ALLOW ADEQUATE AIR CIRCULATION  
DO NOT USE WITH A SWITCHED OUTLET  
CHECK GFCI CORD REGULARLY  
MINIMIZE DOOR OPENING TIME  
ALLOW 24 HOURS TO COOL A FULL LOAD OF ROOM TEMPERATURE BEVERAGES  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Felix Storch, Inc.  
Page 14  
SUMMIT PROFESSIONAL DIV.  
INSTALLING A PANEL INTO A SUMMIT FRAME (“FR” SUFFIX)  
On any model that includes suffix “FR” in the model number, and on all models BI540, BI541,ALB651, ALB653B,  
ALB751 and ALB753B) a two piece stainless steel frame is mounted on the door. The models can be used without a  
panel, but to install a panel follow the directions below. (Panel size is 23 1/8” W x 28 1/8” H)  
1. Carefully lay the refrigerator (it must be empty) on its back.  
2. Unscrew the small piece of frame from the bottom. For a thin metal panel use a backing piece of cardboard  
3. Slide panel into frame and replace the bottom frame and reattach the screws.  
BEFORE CALLING FOR SERVICE….  
Before calling for assistance or service, please check “Troubleshooting.” It may save you the cost of a service call. If  
you still need help, follow the instructions below.  
When calling, please know the purchase date and the complete model and serial number of your appliance. This in-  
formation will help us to better respond to your request.  
If You Need Replacement Parts  
If you need to order replacement parts, we recommend that you only use factory specified parts. Factory specified  
parts will fit right and work right, because they are made with the same precision used to build every new SUMMIT®  
appliance.  
Check the plug, fuse and/or circuit breaker.  
Test the outlet with a lamp  
Make certain that the outlet used is not controlled by a wall switch. This is more common in outdoor kitchens.  
Be sure the control is not set to 0 (OFF).  
On outdoor units, check that the GFCI switch on the line cord is on. If necessary press the reset button.  
Read the manual, especially the items under troubleshooting. You may find the answer to your question.  
If you don’t find the answer to your question in this manual, find the unit model number (on the serial tag) and try our  
Accessories available for your SUMMIT Built-in Under-Counter Models  
The following accessories are available at www.summitapplianceparts.com to enhance the beauty or  
functionality of your new refrigerator or freezer.  
Accessory  
Description  
Finish  
Fits models  
Level leg shield  
Solid grill that fits below two front level legs and Black  
hides the legs. Acts as a base grill extension.  
All FF6, FF7, BI540, BI541, FS62, CT66, CT67, SCC6G, SCFF55, SCR600,  
Outdoor models, All Drawer units, All Models beginning with ALB65 or  
ALB75  
Stainless steel  
kickplate  
Replaces the standard white or black kickplate Stainless  
All FF6, FF7, BI540, BI541, FS62, CT66, CT67< SCC6G, SCFF55, SCR600,  
Outdoor models, All Drawer units, All Models beginning with ALB65 or  
ALB75  
with one in full stainless steel  
steel  
Stainless steel  
top hinge  
Replace the hinge cap and cover with a laser  
cut solid stainless steel hinge for a commercial steel  
look  
Stainless  
All FF6, FF7, BI540, BI541, FS62, CT66, CT67< SCC6G, SCFF55, SCR600,  
Outdoor models, All Drawer units, All Models beginning with ALB65 or  
ALB75  
Stainless steel  
shelves  
Set of stainless steel shelves to replace wire or Stainless  
All FF6, FF7, BI540, BI541, FS62, CT66, CT67< SCC6G, SCFF55, SCR600,  
Outdoor models, All Drawer units, All Models beginning with ALB65 or  
ALB75  
glass shelves supplied with the unit  
steel  
Keys  
Spare keys for models with front push-to-turn  
locks  
Chrome /  
black  
All FF6L, FF7L, CT66L, BI540L, SCR600L, SCR600BL, SPR7OS (Summit  
brand only), FS62L, SCFF55L, FF7LBL, SWC6GBL, SPR601OS,  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Felix Storch, Inc.  
Page 15  
SUMMIT PROFESSIONAL DIV.  
TROUBLESHOOTING  
Try the solutions suggested here first to avoid the cost of an unnecessary service call...  
Your refrigerator or freezer will not operate:  
Has a household fuse blown or circuit breaker tripped, or is the outlet not receiving power or switch controlled?  
Replace the fuse or reset the circuit breaker. Check the outlet with a small appliance you know works.  
• Is the refrigerator or freezer defrosting (on some models)?  
Recheck to see whether the appliance is operating in a few hours. It may regularly run an automatic defrost cycle.  
There is water in the defrost drain pan (on some models):  
• Is the appliance defrosting? The water will evaporate. It is normal for water to drip into the defrost pan.  
• Is it more humid than normal? When it is humid, expect that the water in the defrost pan will take longer to evaporate.  
The motor seems to run too much:  
• Is there excessive frost or a package preventing the door from closing? Defrost and clean the appliance, or move  
the package so the door closes properly.  
• Is the room temperature hotter than normal? The motor will run longer under warm conditions. At normal room  
temperatures, your motor will run about 40% to 80% of the time. Under warmer conditions, it will run even more.  
Has a large amount of food just been added to the appliance? Adding a large amount of food warms the refrigerator  
or freezer. The motor normally will run longer to cool the appliance back down.  
• Is the door closed completely? Push the door firmly shut. If it will not shut all the way, see “The door will not close  
completely” later in this section.  
• Are the condenser coils dirty (on some models)? This prevents air transfer and makes the motor work harder. Clean  
the condenser coils.  
Is the door gasket sealed all the way around? Contact a qualified technician.  
NOTE: If the problem is not due to any of the above, remember that the compressor on your new appliance will  
operate longer than your old one due to its high-efficiency motor.  
The interior temperature is too warm:  
• Are the air vents blocked? This prevents cold air movement. Move objects away from the air vents. See “Ensuring  
Proper Air Circulation” for air vent locations.  
• Is the door opened often? Be aware that the refrigerator or freezer will warm when this occurs. In order to keep the  
appliance cool, try to get everything you need out of it at once, keep food organized so it is easy to find, and close the door  
as soon as the food is removed.  
• Has a large amount of food just been added? Adding a large amount of food warms the refrigerator or freezer. It can  
take several hours to return to the normal temperature.  
The door will not close completely or is difficult to open:  
• Are food packages blocking the door? Rearrange containers so that they fit more tightly and take up less space.  
• Are the shelves and basket out of position (on some models)? Put the shelves and basket back into their correct  
positions.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WARRANTY  
Call customer service toll free in the U.S.A. @ 1-800-287-8799; Monday to Friday 9:00 am. - 5:00 p.m. (EST).  
ONE YEAR LIMITED WARRANTY  
Within the 48 contiguous United States, for one year from the date of purchase, when this appliance is operated and maintained accord-  
ing to instructions attached to or furnished with the product, warrantor will pay for factory specified parts and repair labor to correct de-  
fects in materials or workmanship. Service must be provided by a designated service company. Outside the 48 states, all parts are war-  
ranted for one year from manufacturing defects. Plastic parts, shelves and cabinets are warranted to be manufactured to commercially  
acceptable standards, and are not covered from damage during handling or from breakage.  
5 YEAR COMPRESSOR WARRANTY  
1. The compressor is covered for 5 years.  
2. Replacement does not include labor.  
ITEMS WARRANTOR WILL NOT PAY FOR:  
1. Service calls to correct the installation of your appliance, to instruct you how to use your appliance, to replace or repair fuses or to  
correct wiring or plumbing.  
2. Service calls to repair or replace appliance light bulbs or broken glass shelves. Consumable parts (such as filters) are excluded from  
warranty coverage.  
3. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation, installation not in accordance  
with electrical or plumbing codes, or use of products not approved by warrantor.  
4. Replacement parts or repair labor costs for units operated outside the United States.  
6. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.  
7. Expenses for travel and transportation for product service in remote locations.  
8. The removal and reinstallation of your appliance if it is installed in an inaccessible location or is not installed in accordance with pub-  
lished installation instructions.  
DISCLAIMER OF IMPLIED WARRANTIES;  
LIMITATION OF REMEDIES  
CUSTOMER’S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PRO-  
VIDED HEREIN. IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR  
PURPOSE, ARE LIMITED TO ONE YEAR . WARRANTOR SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAM-  
AGES. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, OR  
LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS, SO THESE EXCLUSIONS  
OR LIMITATIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO  
HAVE OTHER RIGHTS, WHICH VARY FROM STATE TO STATE.  
Phone: (718) 328-8700  
Fax: (718) 842-3093  
Web Site:  
Felix Storch, Inc.  
770 Garrison Avenue  
Bronx, NY 10474  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Sharp Cash Register TCADH2556RCZZ User Manual
Sharp TV VCR Combo 32C530 User Manual
Soleus Air Dehumidifier CFM 25E User Manual
Sony Beverage Dispenser KDL 32XBR6 User Manual
Sony Clock Radio ICFC1B User Manual
Sony Ericsson CD Player DVP NS708H User Manual
Sony Universal Remote RMF CD003 User Manual
Stiga Chipper BIO 2000 User Manual
Stiga Lawn Mower 5 96 User Manual
Sunpentown Intl Air Conditioner WA 1010E User Manual