SCC 24-Pump 128-Station Controller
Part Number: 882.00255.00
Bulletin Number: CV3-655
Effective: 12/1/05
Write Down Your Serial Numbers Here For Future Reference:
_________________________
_________________________
_________________________
_________________________
_________________________
_________________________
We are committed to a continuing program of product improvement.
Specifications, appearance, and dimensions described in this manual are subject to change without notice.
DCN No. ____________
© Copyright 2005
All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
Shipping Information
Unpacking and Inspection
You should inspect your equipment for possible shipping damage. Thoroughly check the
equipment for any damage that might have occurred in transit, such as broken or loose wiring
and components, loose hardware and mounting screws, etc.
In the Event of Shipping Damage
According to the contract terms and conditions of the Carrier, the responsibility of the
Shipper ends at the time and place of shipment.
Notify the transportation company’s local agent if you discover damage
Hold the damaged goods and packing material for the examining agent’s inspection. Do not
return any goods before the transportation company’s inspection and authorization.
File a claim with the transportation company. Substantiate the claim by referring to the
agent’s report. A certified copy of our invoice is available upon request. The original Bill of
Lading is attached to our original invoice. If the shipment was prepaid, write us for a
receipted transportation bill.
Advise customer service regarding your wish for assistance and to obtain an RMA (return
material authorization) number.
If the Shipment is Not Complete
Check the packing list as back-ordered items are noted on the packing list. In addition to the
equipment itself, you should have:
;..Bill of lading
;..Packing list
;..Operating and Installation packet
; Electrical schematic and panel layout drawings
;..Component instruction manuals (if applicable)
Re-inspect the container and packing material to see if you missed any smaller items during
unpacking.
If the Shipment is Not Correct
If the shipment is not what you ordered, contact the shipping department immediately. For
shipments in the United States and Canada, call 1 (630) 595-1060; for all other countries, call
our international desk at (630) 595-1060. Have the order number and item number available.
Hold the items until you receive shipping instructions.
Returns
Do not return any damaged or incorrect items until you receive shipping instructions from the
shipping department.
24-Pump, 128-Station Controller
Chapter 1: Safety
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
CHAPTER 1: SAFETY ................................................................5
1-1
How to Use This Manual .............................................................................................5
Safety Symbols Used in this Manual.....................................................................5
Warnings and Precautions ..........................................................................................6
Responsibility ..............................................................................................................7
General Responsibility...........................................................................................7
Operator Responsibility.........................................................................................7
Maintenance Responsibility...................................................................................8
Reporting a Safety Defect .....................................................................................8
1-2
1-3
CHAPTER 2: FUNCTIONAL DESCRIPTION..............................9
2-1
2-2
2-3
Models Covered in This Manual..................................................................................9
General Description.....................................................................................................9
Standard Features.......................................................................................................9
Mechanical Features.............................................................................................9
Electrical Features...............................................................................................10
Controller Features..............................................................................................10
Optional Features......................................................................................................10
Safety Devices and Interlocks...................................................................................10
Safety Circuit Standards......................................................................................11
Fail Safe Operation .............................................................................................11
Safety Device Lock-Outs.....................................................................................11
2-4
2-5
CHAPTER 3: INSTALLATION ..................................................12
3-1
3-2
3-3
3-4
Uncrating...................................................................................................................12
Mounting the Control Panel.......................................................................................12
System Installation Overview ....................................................................................12
Electrical Connections...............................................................................................13
Making Control Panel Power Drop Wiring Connections......................................13
Running KwikLink™ Cables................................................................................13
Setting Up and Installing Mounting Plates...........................................................14
Terminating Cable Runs......................................................................................15
Addressing and Installing ArmorBlocks™ ...........................................................17
Installing KwikLink™ Connectors........................................................................20
Connecting the Controller to the Network............................................................21
Connecting the Power Supply Enclosure to the Network....................................23
Connecting Vacuum Receivers to the Network...................................................25
Connecting Vacuum Pumps and Filter Chambers to the Network ......................28
Connecting Central Alarms to the Network .........................................................34
Setup.........................................................................................................................36
Setting Up the System.........................................................................................37
Setting Up Stations..............................................................................................41
Setting Up Pumps ...............................................................................................44
Finishing Setup: Setting Up Passwords ..............................................................48
Save/Restore Settings.........................................................................................49
3-5
3-6 Initial Startup...............................................................................................................50
CHAPTER 4: OPERATION ........................................................51
24-Pump, 128-Station Controller
Chapter 1: Safety
3
Download from Www.Somanuals.com. All Manuals Search And Download.
4-1
4-2
4-3
Overview ...................................................................................................................51
Starting and Stopping the System.............................................................................51
Basic Tasks...............................................................................................................52
Reviewing Station Status ....................................................................................52
Reviewing Pump Status ......................................................................................53
Logging On and Logging Off ...............................................................................54
Enabling and Disabling Stations and Pumps.......................................................55
Reviewing and Adjusting Basic Station Settings .................................................56
Advanced Tasks........................................................................................................59
Reviewing and Resetting a Pump Hour Meter ....................................................59
Transferring Stations to a Standby Pump............................................................59
Alarms .......................................................................................................................62
Reviewing Alarms................................................................................................62
Silencing Alarms..................................................................................................62
4-4
3-5
CHAPTER 5: MAINTENANCE..................................................63
5-1
5-2
Preventative Maintenance.........................................................................................63
Corrective Maintenance ............................................................................................63
Network Scanner Module Considerations ...........................................................63
CHAPTER 6: CONFIGURABLE SETTINGS.............................64
6-1
6-2
6-3
Memory Module Considerations................................................................................64
Options for Station Setup ..........................................................................................64
Options for Pump Setup............................................................................................69
CHAPTER 7: TROUBLESHOOTING........................................71
7-1
General Troubleshooting...........................................................................................71
7-2 Alarms..........................................................................................................................72
Station Alarms.....................................................................................................72
Pump Alarms.......................................................................................................74
System Alarms ....................................................................................................74
CHAPTER 8: APPENDIX ..........................................................75
8-1
8-2
8-3
8-4
8-5
Warranty....................................................................................................................75
Optional Components................................................................................................75
Drawings and Diagrams............................................................................................76
Spare Parts List.........................................................................................................77
Returned Material Policy ...........................................................................................78
Credit Returns .....................................................................................................78
Warranty Returns ................................................................................................78
Safety Tag Information..............................................................................................79
Controller Safety Tags.........................................................................................79
Controller Identification (Serial Number) Tag............................................................79
Technical Assistance (Contact Information)..............................................................80
Parts Department ................................................................................................80
Service Department.............................................................................................80
Sales Department................................................................................................80
Contract Department...........................................................................................80
8-6
8-7
8-8
24-Pump, 128-Station Controller
Chapter 1: Safety
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1: Safety
1-1 How to Use This Manual
Use this manual as a guide and reference for installing, operating, and maintaining your
equipment. The purpose is to assist you in applying efficient, proven techniques that enhance
equipment productivity.
This manual covers only light corrective maintenance. No other maintenance should be
undertaken without first contacting a service engineer.
The Functional Description section outlines models covered, standard features, and optional
features. Additional sections within the manual provide instructions for installation, pre-
operational procedures, operation, preventive maintenance, and corrective maintenance.
The Installation chapter includes required data for receiving, unpacking, inspecting, and setup
of the equipment. We can also provide the assistance of a factory-trained technician to help
train your operator(s) for a nominal charge. This section includes instructions, checks, and
adjustments that should be followed before commencing with operation of the equipment.
These instructions are intended to supplement standard shop procedures performed at shift,
daily, and weekly intervals.
The Operation chapter includes a description of electrical and mechanical controls, in
addition to information for operating the equipment safely and efficiently.
The Maintenance chapter is intended to serve as a source of detailed assembly and
disassembly instructions for those areas of the equipment requiring service. Preventive
maintenance sections are included to ensure that your equipment provides excellent, long
service.
The Troubleshooting chapter serves as a guide for identification of most common problems.
Potential problems are listed, along with possible causes and related solutions.
The Appendix contains technical specifications, drawings, schematics, and parts lists. A
spare parts list with part numbers specific to your machine is provided with your shipping
paperwork package. Refer to this section for a listing of spare parts for purchase. Have your
serial number and model number ready when ordering.
Safety Symbols Used in this Manual
The following safety alert symbols are used to alert you to potential personal injury hazards.
Obey all safety messages that follow these symbols to avoid possible injury or death.
Danger!
Warning!
Caution!
DANGER indicates an imminently hazardous situation which, if not
avoided, will result in death or serious injury.
WARNING indicates a potentially hazardous situation or practice which,
if not avoided, could result in death or serious injury.
CAUTION indicates a potentially hazardous situation or practice which, if
not avoided, may result in minor or moderate injury or in property
damage.
24-Pump, 128-Station Controller
Chapter 1: Safety
5
Download from Www.Somanuals.com. All Manuals Search And Download.
1-2 Warnings and Precautions
Our equipment is designed to provide safe and reliable operation when installed and operated
within design specifications, following national and local safety codes. This may include, but
is not limited to OSHA, NEC, CSA, SPI, and any other local, national and international
regulations.
To avoid possible personal injury or equipment damage when installing, operating, or
maintaining this equipment, use good judgment and follow these safe practices:
; Read and follow these operation and installation instructions when installing,
operating, and maintaining this equipment. If these instructions become
damaged or unreadable, additional copies are available from the manufacturer.
; Follow all SAFETY CODES.
; Wear SAFETY GLASSES and WORK GLOVES.
; Work only with approved tools and devices.
; Disconnect and/or lock out power before servicing or maintaining the equipment.
; Use care when LOADING, UNLOADING, RIGGING, or MOVING this
equipment.
; Operate this equipment within design specifications.
; OPEN, TAG, and LOCK ALL DISCONNECTS before working on equipment.
You should remove the fuses and carry them with you.
; Make sure the equipment and components are properly GROUNDED before you
switch on power.
; Use extreme caution when working with your conveying system. HIGH VACUUM
can be dangerous. Keep body parts, tools, clothing, and debris away from vacuum
inlets.
; When welding or brazing in or around this equipment, make sure VENTILATION is
ADEQUATE. PROTECT adjacent materials from flame or sparks by shielding with
sheet metal. An approved FIRE EXTINGUISHER should be close at hand and
ready for use if needed.
; Do not restore power until you remove all tools, test equipment, etc., and the
equipment and related components are fully reassembled.
; Only PROPERLY TRAINED personnel familiar with the information in this
manual should work on this equipment.
We have long recognized the importance of safety and have designed and manufactured our
equipment with operator safety as a prime consideration. We expect you, as a user, to abide
by the foregoing recommendations in order to make operator safety a reality.
24-Pump, 128-Station Controller
Chapter 1: Safety
6
Download from Www.Somanuals.com. All Manuals Search And Download.
1-3 Responsibility
These machines are constructed for maximum operator safety when used under standard
operating conditions and when recommended instructions are followed in the maintenance
and operation of the machine.
All personnel engaged in the use of the machine should become familiar with its operation as
described in this manual.
Proper operation of the machine promotes safety for the operator and all workers in its
vicinity.
Each individual must take responsibility for observing the prescribed safety rules as outlined.
All warning and danger signs must be observed and obeyed. All actual or potential danger
areas must be reported to your immediate supervisor.
General Responsibility
No matter who you are, safety is important. Owners, operators and maintenance personnel
must realize that every day, safety is a vital part of their jobs.
If your main concern is loss of productivity, remember that production is always affected in a
negative way following an accident. The following are some of the ways that accidents can
affect your production:
• Loss of a skilled operator (temporarily or permanently)
• Breakdown of shop morale
• Costly damage to equipment
• Downtime
An effective safety program is responsible and economically sound.
Organize a safety committee or group, and hold regular meetings. Promote this group from
the management level. Through this group, the safety program can be continually reviewed,
maintained, and improved. Keep minutes or a record of the meetings.
Hold daily equipment inspections in addition to regular maintenance checks. You will keep
your equipment safe for production and exhibit your commitment to safety.
Please read and use this manual as a guide to equipment safety. This manual contains safety
warnings throughout, specific to each function and point of operation.
Operator Responsibility
The operator’s responsibility does not end with efficient production. The operator usually has
the most daily contact with the equipment and intimately knows its capabilities and
limitations.
Plant and personnel safety is sometimes forgotten in the desire to meet incentive rates, or
through a casual attitude toward machinery formed over a period of months or years. Your
employer probably has established a set of safety rules in your workplace. Those rules, this
manual, or any other safety information will not keep you from being injured while operating
your equipment.
Learn and always use safe operation. Cooperate with co-workers to promote safe practices.
Immediately report any potentially dangerous situation to your supervisor or appropriate
person.
24-Pump, 128-Station Controller
Chapter 1: Safety
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance Responsibility
Proper maintenance is essential to safety. If you are a maintenance worker, you must make
safety a priority to effectively repair and maintain equipment.
Before removing, adjusting, or replacing parts on a machine, remember to turn off all electric
supplies and all accessory equipment at the machine, and disconnect and lockout electrical
power. Attach warning tags to the disconnect switch.
Be sure that all non-current carrying parts are correctly connected to earth ground with an
electrical conductor that complies with current codes. Install in accordance with national and
local codes.
When you have completed the repair or maintenance procedure, check your work, remove
your tools. Rigging, and handling equipment.
Reporting a Safety Defect
If you believe that your equipment has a defect that could cause injury, you should
immediately discontinue its use and inform the manufacturer.
The principle factors that can result in injury are failure to follow proper operating procedures
(i.e. lockout/tagout), or failure to maintain a clean and safe working environment.
24-Pump, 128-Station Controller
Chapter 1: Safety
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Functional Description
2-1 Models Covered in This Manual
This manual provides operation, installation, and maintenance instructions for 24-Pump, 128-
Station Conveying Controllers. Model numbers are listed on the serial tag. Make sure you
know the model and serial number of your equipment before contacting the manufacturer for
parts or service.
The 24-Pump, 128-Station Conveying Controller is a programmable logic controller, with 24
VDC control circuit, easy-to-use touch screen operator interface terminal and optional
audible/visual alarm.
2-2 General Description
Our material conveying systems create vacuum for the automatic conveying of most free-
flowing, dry, pelletized, or granular materials. Material characteristics determine the type of
equipment needed to convey the material.
A typical use for our equipment is an in-plant distribution system for plastic processing
plants.
Our central vacuum systems are as varied as the applications they service. The tubing and
equipment furnished in our system is designed to convey the material(s) specified at the time
of purchase at specific rates and distances.
We can advise you on your system capabilities based on system makeup, distance, material,
and conveying rates you want.
System capacity is directly affected by the pressure drop in the overall system, such as
number of material line bends, pipe length, Y-tubes, T-tubes, etc.
Use the minimum effective amount of vinyl flex hose to maximize material line efficiency.
Keep material lines as straight as possible. Refer to the Mechanical Components Product
manual (Part No. A0536580) for installation recommendations.
Note: Vacuum leaks occurring anywhere in your system reduce capacity.
2-3 Standard Features
Mechanical Features
Time-fill Capability. The specific length of time allowed for material to convey to a station.
Volume-fill Capability. Allows for a station to be conveyed to until the prox at the top of
the station detects material.
Vent Valve. The vent valve unloads the vacuum pump motor and allows it to keep running
during short periods when material conveying is not required. Constantly starting and
stopping the vacuum pump will damage it over time. The vent valve also protects the
conveying system from damage during high vacuum conditions. The valve plunger will
unseat itself and allow ambient air to leak into the vacuum lines when the vacuum climbs too
high.
Central Purging. This feature allows any remaining material to be cleaned out of the
material line after every convey.
Local Blowback Filter Cleaning. When this feature is enabled, the controller periodically
sends compressed air backward through the pump’s air filter to dislodge accumulated dust
and debris.
24-Pump, 128-Station Controller
Chapter 2: Functional Description
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Implosion Filter Cleaning. When this feature is enabled, the controller periodically pulls a
vacuum on the filter chamber and then releases it to dislodge accumulated dust and debris.
Grinder Empty. This feature allows a station to receive material from a grinder bin. The
level of material in the bin is monitored to assure there is enough material to convey.
Material Sharing. This feature allows multiple pumps (6 max.) to be connected to a
material source. The controller will let one pump at a time draw from the material source.
Electrical Features
• 115/1/60 or 220/1/50 supply voltage
• 24 VDC control voltage
• Lockable ON/OFF switch
• Branch circuit fusing
• Fully accessible NEMA 12-style electrical control enclosure
Controller Features
• Allen-Bradley Compact Logix programmable controller with 10” color touch screen
operator interface
• Diagnostics, operating instructions and parts information are built into the interface
• Controls up to one hundred twenty-eight (128) stations and up to twenty-four (24)
Vacuum Power Units.
• Controls up to three central alarms
• Allows operator to transfer stations to a standby pump when a pump fails
• Electronic time delay between pump startups to prevent an excessive power demand at
your facility
2-4 Optional Features
Noise Filter/Surge Suppressor. Provides protection to electronic devices in the control
panel from power surges and electrical noise.
Closed-Loop Conveying. This feature allows material to be conveyed and processed
without being contaminated by outside influences (such as dust, other materials, etc.).
Additional audible/visual alarm with silence button. Alarm light and horn assembly that
can be remote mounted and wired into the controller to indicate an alarm condition.
Remote Interface. (4 max.)
2-5 Safety Devices and Interlocks
This section includes information on safety devices and procedures that are inherent to the
Controller. This manual is not intended to supersede or alter safety standards established by
the user of this equipment. Instead, the material contained in this section is recommended to
supplement these procedures in order to provide a safer working environment.
At the completion of this section, the operator and maintenance personnel will be able to do
the following:
24-Pump, 128-Station Controller
Chapter 2: Functional Description
10
Download from Www.Somanuals.com. All Manuals Search And Download.
•
•
•
Identify and locate specific safety devices.
Understand the proper use of the safety devices provided.
Describe the function of the safety device.
Safety Circuit Standards
Safety circuits used in industrial systems protect the operator and maintenance personnel
from dangerous energy. They also provide a means of locking out or isolating the energy for
servicing equipment.
Various agencies have contributed to the establishment of safety standards that apply to the
design and manufacture of automated equipment. The Occupational Safety and Health
Administration (OSHA) and the Joint Industrial council (JIC) are just a few of the
organizations that have joined with the plastics industry to develop safety standards.
Every effort has been made to incorporate these standards into the design of the controller;
however, it is the responsibility of the personnel operating and maintaining the equipment to
familiarize themselves with the safety procedures and the proper use of any safety devices.
Fail Safe Operation
If a safety device or circuit should fail, the design must be such that the failure causes a
“Safe” condition. As an example, a safety switch must be a normally open switch. The switch
must be held closed with the device it is to protect. If the switch fails, it will go to the open
condition, tripping out the safety circuit.
At no time should the safety device fail and allow the operation to continue for example, if a
safety switch is guarding a motor, and the safety switch fails, the motor should not be able to
run.
Safety Device Lock-Outs
Some safety devices disconnect electrical energy from a circuit. The safety devices that are
used in this Controller are primarily concerned with electrical power disconnection.
WARNING! Always disconnect and lockout all electrical power and pneumatic (i.e. compressed air)
sources prior to servicing the 24-Pump, 128-Station Controller. Failure to do so may
result in serious injury. No one but the person who installed the lockout may remove
it.
24-Pump, 128-Station Controller
Chapter 2: Functional Description
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3: Installation
3-1 Uncrating
24-Pump, 128-Station Controllers are shipped mounted on a skid, enclosed in a plastic
wrapper, and contained in a cardboard box.
1. Pry the crating away from the skid.
Note: Remove the nails holding the box to the skid and lift the box off
carefully; avoiding staples in the 1’ x 4’ wood supports. Cut the steel
banding.
2. Use a pry bar to remove the blocks securing the unit to the skid.
3. Lift unit from sides, inserting forklift under the base. The forks must be equidistant
from the centerline of the unit and the unit must be balanced on the forks. Lift
slowly and only high enough to clear the skid. Use a pry bar if necessary to
carefully remove the skid from the unit.
4. Lower slowly.
3-2 Mounting the Control Panel
Note: Before you mount the panel, consider how you run wiring to the
KwikLink connectors, ArmorBlocks, vacuum hoppers, the filter cham-
ber atmospheric valve (if so equipped) and the pump motor starter(s),
vacuum switch(es), and vent valve(s).
Mount the control panel on a flat, vertical area. It should be a visible area that gives your
operator access to the control. The panel requires a low voltage power drop as listed on the
serial tag.
3-3 System Installation Overview
Installing the 24-pump 128-station controller is easy and straightforward. Because the system
uses networked distributed I/O modules, you’ll only need to run two cables for the entire
system.
The following is a typical installation sequence:
1. Set up mounting plates with tubing clamps; install KwikLink™ connectors and
ArmorBlocks bases onto mounting plates as required.
2. Install KwikLink connectors and ArmorBlock™ base plates to vacuum tubing at each
node location, just before a T-fitting or valve.
3. Run the black power and the grey network flat cables from the start of the system to
the end, attaching them to vacuum tubing with nylon cable ties
4. Install cable terminations.
5. Determine location of network system nodes, and set addresses for ArmorBlocks as
required.
6. Set up and connect to the controller and, if purchased, remote display. Connect grey
patch cords from controller terminals to KwikLink connectors installed in Step 3.
7. After determining quantity and location(s) of where to install system power
supply(ies) (consult factory); set up and connect to KwikLink connectors installed in
Step 3.
24-Pump, 128-Station Controller
Chapter 3: Installation
12
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Set up and connect vacuum receiver stations to ArmorBlocks installed in Step 3,
using yellow patch cords.
9. Set up and connect vacuum pump stations and filter chambers to ArmorBlocks
installed in Step 3, using yellow patch cords.
10. Determine location(s) of central alarm(s); set up and connect alarms using yellow
patch cords.
The following sections provide detailed information on these installation steps.
3-4 Electrical Connections
Refer to local electrical codes, the schematic and connection diagrams supplied with this unit
and the serial tag for wiring considerations. Run all wiring in conduit if codes require it.
Making Control Panel Power Drop Wiring Connections
Hardwire the input power at 115/1/50-60 VAC or 220/1/50 VAC, depending on the
specifications, which are located on the Control Panel Serial Tag. The control enclosure
draws less than five (5) amps during normal operation at 115/1/50-60 VAC. The main power
switch is located on the right side of the enclosure.
Caution!
We recommend that you protect PLC memory by providing the control
panel with a dedicated circuit, a true earth ground, and a spike/surge
protector.
Running KwikLink™ Cables
About KwikLink Flat Cables
KwikLink flat cable is physically keyed to prevent wiring mishaps. This type of cable is
unshielded and contains four conductors. Use a long-jawed straight-bladed cable cutter at
least 1½” long to cut KwikLink flat cable.
You’ll install two (2) colors of flat cable: black and grey. The black cable transmits output
power, and the grey cable transmits input power and data transmission.
Figure 1: KwikLink Cable Cross-Section, Edge Identification
Cross Section
Edge Identification
Installing KwikLink Cable
Before you install flat cable, determine how much length you need to install black power
cable and grey data cable. Typical installations have equal lengths of each. This is a good
time to plan for the future, and run these cables to each possible location in the plant. Use a
straight-blade cable cutter to make the cut at each end.
24-Pump, 128-Station Controller
Chapter 3: Installation
13
Download from Www.Somanuals.com. All Manuals Search And Download.
To install KwikLink cables:
1. Cut both black and grey cables to the proper length.
2. Use cable ties to attach KwikLink cables, black cable above grey cable, on the
vacuum tubing. Attach cable to the tubing with cable ties at about three-foot (3 ft./
1 m) intervals. Make sure that cable ties are snug, but not tightened enough to bend the
flat cable.
Caution!
Install KwikLink cable on vacuum tubing only. DO NOT install KwikLink
cable on material conveying tubing, as static electricity formed at material
lines could disrupt system operation.
Figure 2: Side View of a Typical Power Cable and Data Cable Installation
Cable tie, buckle
Black power cable
Vacuum tube
Grey data cable
Note: When approaching a node location, stop the attachment process. Run
the cables over the node area (such as a T-valve) and make sure you
create a slight amount of slack when continuing the attachment with
cable ties. Doing so lets you install KwikLink connectors or
ArmorBlocks with greater ease, with less stress on the cable.
Setting Up and Installing Mounting Plates
Setting Up Mounting Plates
It’s a good idea to get all your mounting plates set up with KwikLink connector bases or
ArmorBlock cable bases before installation, as your system layout determines.
Note: ArmorBlock cable bases are installed on mounting plates
perpendicular in orientation to the flat cable runs.
Vacuum hoppers/receiver stations and vacuum pumps require 8-connector
ArmorBlocks; central alarm stations require 4-connector ArmorBlocks.
Make sure that each mounting plate has properly attached tube clamps as required. Each
mounting plate requires two (2) tube clamps. Always use locking washers, especially in
high-vibration environments.
24-Pump, 128-Station Controller
Chapter 3: Installation
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 3: Side View of a Typical Mounting Plate Assembly with ArmorBlock Base
Rotate 30º to 45º downward
Installing Assembled Mounting Plates
After you’ve set up the mounting plates:
1. Install them at each node location by clipping the tubing clamps onto the vacuum
tube, just before the node area (such as a T-valve).
2. Orient the mounting plate parallel with the flat cables and at a 30º to 45º angle so the
KwikLink connector or ArmorBlock faces the operator on the floor; torque the tubing
clamp fasteners until tight.
The flat cable will be installed inside KwikLink connectors and ArmorBlocks as described in
the following sections of this chapter.
Terminating Cable Runs
After you’ve run the black and grey network cables, you need to properly terminate the ends
of the cables. By doing so, you’ll insure that the network runs properly. You will also have
the benefit of being able to measure voltage in the system without disrupting operation.
This section lists procedures for terminating these cables. To properly terminate a cable run:
1. Mount three standard KwikLink connectors to a mounting plate in a triangle
configuration. See Figure 4 on Page 19 for an illustration.
Make sure that each connector is installed with the hinge side down.
2. Mount the tubing clamps to the mounting plates. Each mounting plate requires two
(2) tubing clamps.
3. Mount the standard resistor cap from the KwikLink connector kit on the top center
KwikLink connector for the black power flat cable. The standard resistor cap has
metal prongs in the center.
Repeat for the outside end KwikLink connector on the grey data flat cable.
4. For the inside KwikLink connector (next to the outside end on the grey cable), mount
a separately-packaged blank cap on it instead of the standard resistor cap in the
KwikLink connector kit.
24-Pump, 128-Station Controller
Chapter 3: Installation
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Discard the standard resistor cap to eliminate confusion.
5. Mount the mounting plate assembly on the vacuum line at the end of the cable run.
See Page 14 for more information.
6. Using the straight-blade cable cutter, carefully trim each flat cable so it sticks out past
the final KwikLink connector by 1/4” to 3/8”.
Place a dust cap over the end of the trimmed cable.
7. Lay the dust cap and cable into the KwikLink connector so the dust cap tabs engage
in the connector slots. The dust cap tabs should fit into the connector slots perfectly.
Left
Right
8. Lay the cable in the hinged base, noting the correct keyed profile; flat edge toward
the hinge, keyed edge toward the latch. Make sure that the cable and dust cap are
properly seated inside.
9. Making sure that the cable is completely straight, carefully close the hinged
assembly, and apply firm, even pressure until the first latch locks into place.
Note: Make sure that the flat cable is completely straight before continuing!!
The latch has two catches; the first loosely holds the connector on the cable, the
second requires more pressure to close the connector tightly. The cable must be in the
correct position for the connector to close properly.
10. Drive the two screws at the center points about halfway down; first on the latch side,
then the hinge side.
11. Continue to tighten the screws a little at a time until fully tightened; no more than 15
inch-pounds (5.6 N•m) of torque.
Note: You can only pierce the cable once. Once pierced, the KwikLock
connector must not be removed. This insures that the inner conductors
are not exposed to the elements.
Installing Inside KwikLink Connectors with Blank Caps
Once installed on the grey data cables, these connectors permit you to measure voltage in the
system so you can analyze how it is working. The system cannot work properly unless these
inside-mounted connectors have the blank (non-conductor) caps installed.
1. Lay the cable in the hinged base, noting the correct keyed profile; flat edge toward
the hinge, keyed edge toward the latch. Make sure that the cable is properly seated
inside.
2. Making sure that the cable is completely straight, carefully close the hinged
assembly, and apply firm, even pressure until the first latch locks into place.
Note: Make sure that the flat cable is completely straight before continuing!!
24-Pump, 128-Station Controller
Chapter 3: Installation
16
Download from Www.Somanuals.com. All Manuals Search And Download.
The latch has two catches; the first loosely holds the connector on the cable, the
second requires more pressure to close the connector tightly. The cable must be in the
correct position for the connector to close properly.
3. Drive the two screws at the center points about halfway down; first on the latch side,
then the hinge side.
4. Continue to tighten the screws a little at a time until fully tightened; no more than 15
inch-pounds (5.6 N•m) of torque.
Note: You can only pierce the cable once. Once pierced, the KwikLock
connector must not be removed. This insures that the inner conductors
are not exposed to the elements.
The system should now be properly terminated. You can now continue to install components
on the system.
Figure 4: Proper Termination Connections
Addressing and Installing ArmorBlocks™
Addressing ArmorBlocks
An ArmorBlock permits you to give it a number “address” so that the controller network
system can recognize its location and function. ArmorBlocks are used at vacuum
hopper/receiver, pump, and alarm node locations.
ArmorBlock Address Ranges
The number range of ArmorBlock addresses are as follows:
• 01 to 32 — Vacuum hopper/receiver stations; use a leading zero for
numbers 01 to 09.
• 33 to 44 — Pump stations
• 45 to 60 — Central purge valves
24-Pump, 128-Station Controller
Chapter 3: Installation
17
Download from Www.Somanuals.com. All Manuals Search And Download.
• 61 to 63 — Alarm stations
Setting ArmorBlock Addresses
Locate the rotary switches underneath the ArmorBlock. The two switches are:
• MSD (most significant digit) for tens
• LSD (least significant digit) for units/ones
For example, if you wanted to set an address at 36, you set the MSD rotary switch at 3 and
the LSD rotary switch at 6. To set an address of 8, set the MSD rotary switch at 0 (leading
zero), then set the LSD rotary switch at 8.
• Using a permanent black marker, write the number of the address
on the white label located on the bottom front of the ArmorBlock.
We suggest that you place numbered tags at node locations to ease
installation and reduce any confusion of locations.
To set the node address:
• Use a small straight-bladed screwdriver to rotate the switches.
Line up the small arrowhead on the switch with the number you want
to select.
The following figure shows that the address is set at 01; the MSD rotary switch is set at 0 and
the LSD rotary switch is set at 1.
24-Pump, 128-Station Controller
Chapter 3: Installation
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 5: ArmorBlock Address Node Rotary Switches
Installing ArmorBlocks
The ArmorBlock cable base should already be attached to the mounting plate, aligned so it is
perpendicular to the flat cables. If not, reinstall it with its proper alignment.
To install the flat cables in the ArmorBlock cable base:
1. Lay the flat cable into the ArmorBlock cable base, grey data cable on the bottom and
the black power cable on the top, making sure that the keyed edge is properly seated
toward the top.
Caution!
EXERCISE CARE when handling the seal block.
Cable contacts are SHARP!
Only ONE attempt to pierce the cable is allowed for proper contact.
Figure 6: Using seal block to pierce cable
2. Align the seal block so the L-shaped tabs are towards the top, and the arrows are
matched on the bottom of the cable base and seal block. Make sure that the arrows
and the four captive screws on the seal block are properly aligned. Gently press it
into place.
Make sure that you align the seal block properly when you attach it to the base.
Doing so maintains the integrity of the sealed base.
Note: You can only pierce the cable once. Once pierced, the seal block must
not be removed. This insures that the inner conductors are not exposed
to the elements.
Figure 7: Securing the Seal Block to the Cable Base
24-Pump, 128-Station Controller
Chapter 3: Installation
19
Download from Www.Somanuals.com. All Manuals Search And Download.
To secure the seal block:
1. Start the threads of each of the four captive screws into the cable base receptacle
holes.
2. Drive each of the screws about halfway down, using the proper torque sequence:
Bottom screw, top screw, left screw, right screw. Doing so insures that the cables are
pierced evenly.
3. Using the proper torque sequence, tighten each screw, a little at a time, until the
seal block is fully seated into the cable base. Tighten to no more than 8 to 10 inch-
pounds (3.0 to 3.7 N•m) of torque.
The three seat lines on the seal block should meet the cable base, indicating that the
seal block is fully seated. The seal block clips should also click into place onto the
corresponding cable base slots.
Installing KwikLink™ Connectors
KwikLink connectors let you connect the controller and the power supply to the system. They
are also used to electronically terminate power cable and data cable runs.
Just like ArmorBlocks, KwikLink connectors are insulation displacement connectors (IDCs).
Caution!
Exercise care when installing Kwiklink connectors.
IDC blades on KwikLink connectors are SHARP!
Gently push back any protruding IDC blades before installing flat cables
inside.
The KwikLink connector should already be attached to the mounting plate, so the hinge side
is down. If not, reinstall it with its proper alignment, along the correct flat cable. See the
installation drawing located in your Customer Information Packet for further details.
To install flat cable inside KwikLink connectors:
1. Lay the cable in the hinged base, noting the correct keyed profile; flat edge toward
the hinge, keyed edge toward the latch. Make sure that the cable is properly seated
inside.
24-Pump, 128-Station Controller
Chapter 3: Installation
20
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Making sure that the cable is completely straight, carefully close the hinged
assembly, and apply firm, even pressure until the first latch locks into place.
Note: Make sure that the flat cable is completely straight before continuing!
The latch has two catches; the first loosely holds the connector on the cable, the
second requires more pressure to close the connector tightly. The cable must be in the
correct position for the connector to close properly.
3. Drive the two screws at the center points about halfway down; first on the latch side,
then the hinge side.
4. Continue to tighten the screws a little at a time until fully tightened; no more than 15
inch-pounds (5.6 N•m) of torque.
Note: You can only pierce the cable once. Once pierced, the KwikLink
connector must not be removed. This insures that the inner conductors
are not exposed to the elements.
Connecting the Controller to the Network
To connect the controller to the network, make sure that the KwikLink connector is properly
installed on the flat grey data cable. To connect:
1. Attach the keyed round connector to the terminal of the controller marked DeviceNet.
Tighten the cord grip ring until snug.
2. Align the square connector of the grey drop cable so the cable leads down from the
connector. Evenly press the square connector onto the top of the KwikLink
connector. It should make two audible snaps when properly seated.
3. Dress the excess cable with cable ties so it does not interfere with operation and gives
a pleasing appearance.
Connecting the Remote Interface to the Main Controller
After selecting a location and installing the remote interface, connect it to the main controller:
1. Install the Ethernet switch in a location safe from electrical interference and physical
damage.
2. Install the remote interface(s) in their desired locations.
24-Pump, 128-Station Controller
Chapter 3: Installation
21
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Run the cables from the remote interface(s) to the switch and the main controller,
neatly dressing the cable with ties so that it does not interfere with system operation
and it gives a neat appearance.
4. Attach RJ45 connectors at each cable end following the connector manufacturers
instructions.
5. The “Ethernet out” connection on the main controller should connect to the “Ethernet
in” connection on the switch.
6. The “Ethernet out” connections on the switch should connect to the “Ethernet in”
connections on the main controller and the remote interface(s).
24-Pump, 128-Station Controller
Chapter 3: Installation
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 8: Proper Controller and Remote Interface Connections
Connecting the Power Supply Enclosure to the Network
The power supply provides electrical power to make the system work. Some network layouts
require more than one power supply.
Location is also an important consideration when locating power supply enclosures on your
network. Contact the factory for determining how many power supply enclosures your system
needs, as well as where they need to be installed.
After you’ve mounted the power supply enclosure(s), you can connect them to your network.
To connect a power supply to the network:
24-Pump, 128-Station Controller
Chapter 3: Installation
23
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Attach a KwikLink connector included in the bag with power cables to the flat
cables. One connector is used for the network grey cable and one connector is used
for the auxiliary power black cable.
2. Align the square connector of the grey drop cable so the cable leads down from the
connector. Evenly press the square connector onto the top of the bottom KwikLink
connector. It should make two audible snaps when properly seated.
3. Align the square connector of the black drop cable so the cable leads down from the
connector. Evenly press the square connector onto the top of the upper KwikLink
connector. It should make two separate, audible snaps when properly seated.
4. Attach the keyed round connectors to the receptacles on the side of the power supply
enclosure marked 24 VDC POWER SUPPLY. Tighten the cord grip ring until
snug.
5. Dress the excess cables with cable ties so they do not interfere with operation and to
give a pleasing appearance.
If more than one power supply is required to properly energize the grey network flat cable:
1. Remove the terminal block jumpers on all but the most centrally-located network
power supply enclosures.
For locations of jumpers, refer to the drawing shipped inside the power supply
enclosure
Note: Only one power supply should be connected to each section of the
black auxiliary power flat cable. Do not remove any jumpers on power
supplies that transmit energy to the black flat power cable.
24-Pump, 128-Station Controller
Chapter 3: Installation
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 9: Proper Power Supply Enclosure Connections
Connecting Vacuum Receivers to the Network
Make sure that all previous installation steps have been done first before starting this task.
To connect a vacuum receiver to the network:
1. Attach patch cord from vacuum hopper junction box (station demand) to appropriate
input connector. See Figures 10 and 11 (connection is shown on first hopper on the block
only for clarity.)
2. Dress the excess patch cord cable with cable ties so it does not interfere with operation
and gives a pleasing appearance.
24-Pump, 128-Station Controller
Chapter 3: Installation
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 10: 24/128 8-Connector ArmorBlock Connections
Note 1: The block shown is addressed 01 for the first (4) four hoppers. The block addressed 02 would
have the connections for 5-8, etc.
Note 2: If a hopper does not have an optional input or optional output, the T-connector is not
required. Connect the patchcord directly to the connector on the ArmorBlock.
24-Pump, 128-Station Controller
Chapter 3: Installation
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 11: Proper Vacuum Receiver Connections
24-Pump, 128-Station Controller
Chapter 3: Installation
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Vacuum Pumps and Filter Chambers to the Network
Connecting Vacuum Pumps
Make sure that all previous installation steps have been done first before starting this task..
To connect a vacuum pump to the network:
1. Attach patchcords from vacuum pump junction boxes to the appropriate ArmorBlock
connectors. See Figures 12, 13, and 14.
Figure 12: 4-Vacuum Pump ArmorBlock Connections
Note 1: The block shown is addressed 33, for the first (2) pumps. The block addressed
34 would have connectors for pumps 3 and 4, etc.
Note 2: If a pump does not have “Pump Fault #2” or a local pump alarm light, the T
connector is not required. Connect the patchcord directly to the connector on the
ArmorBlock.
24-Pump, 128-Station Controller
Chapter 3: Installation
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 13: Proper Vacuum Pump Connections, Standard XPD/XPC Pumps
24-Pump, 128-Station Controller
Chapter 3: Installation
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 14: Proper Vacuum Pump Connections, XPDB Pump
24-Pump, 128-Station Controller
Chapter 3: Installation
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Filter Chambers
Make sure that all previous installation steps have been done first before starting this task.
To connect a filter chamber to the network:
1. Attach patch cords from vacuum pump filter chamber to the appropriate connector(s).
See Figures 9, 12, 15, and 16 (connection is shown on first pump on the block only
for clarity.)
24-Pump, 128-Station Controller
Chapter 3: Installation
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 15: Proper Filter Chamber Connections, Blowback
24-Pump, 128-Station Controller
Chapter 3: Installation
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 16: Proper Filter Chamber Connections, Implosion Type
Note: Retain the terminal caps from the ArmorBlock. They may be used
later.
2. Dress the excess patch cord cables with cable ties so they do not interfere with
operation and to give a pleasing appearance.
24-Pump, 128-Station Controller
Chapter 3: Installation
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Central Alarms to the Network
Make sure that all previous installation steps have been done first before starting this task.
First, determine where the best location for central alarms should be, and install the
alarm module(s) there. You’ll use two yellow patch cords to connect.
To connect an alarm module to the network:
1. Attach one connector of the first yellow patch cord to the terminal on the alarm
module. Tighten the cord grip ring until snug.
2. Attach the other connector to the upper right terminal of the ArmorBlock. Tighten
the cord grip ring until snug.
24-Pump, 128-Station Controller
Chapter 3: Installation
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 17: Proper Central Alarm Connections
3. Attach one connector of a yellow patch cord to the terminal on the alarm silence
switch module. Tighten the cord grip ring until snug.
4. Attach the other connector to the upper left terminal of the ArmorBlock. Tighten the
cord grip ring until snug.
Note: Retain the terminal caps from the ArmorBlock. They may be used
later.
Note the following illustration for 4-connector central alarm ArmorBlocks:
24-Pump, 128-Station Controller
Chapter 3: Installation
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 18: 4-Connector ArmorBlock Connections for Central Alarms
Alarm Strobe Light (C-O0)
Alarm Horn (C-O1)
Alarm Silence Pushbutton (A-I0)
Alarm Silence Pushbutton (A-I1)
Alarm Strobe Light (D-O2)
Alarm Horn (D-O3)
Alarm Silence Pushbutton (B-I2)
Alarm Silence Pushbutton (B-I3)
4 Input / 4 Output
ArmorBlock for
Central Alarms
5. Dress the excess patch cord cables with cable ties so they do not interfere with
operation and to give a pleasing appearance.
3-5 Setup
This section provides the procedures for configuring your 24-pump 128-station
controller. Configuration of your controller includes setting the number of stations and
pumps, setting variables such as convey time and blow-back interval, and setting up
passwords. We recommend that you carry out these procedures in the order given here.
Note: Before carrying out these procedures, install all equipment as
described in this section and in the Mechanical Components manual.
Figure below gives an overview of the basic flow between the menus used in setting up
the system.
Figure 19: Basic Menu Flow for Setup
24-Pump, 128-Station Controller
Chapter 3: Installation
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Up the System
Setting the Number of Stations and the Number of Pumps
1. Touch System Setup at the Station Status (or Pump Status) screen.
The System Setup screen appears:
Note: Touching Help in the lower right of this screen gives you a menu of
online help for the choices in this screen.
2. Touch Stations Presentin the upper left of the System Setup screen.
3. This will take you to the Stations Installed screen.
A screen showing a list of stations appears. The stations that are not installed are red.
The stations that are installed are green. Briefly touching the icon for a station toggles
between not installed and installed.
4. Press System Setupto return to the System Setup screen.
5. Touch Pumps Presentin the upper part of the System Setup screen.
6. This will take you to the Pumps Installed screen.
The screen shows a list of pumps. The pumps that are not installed are red. The
pumps that are installed are green. Briefly touching the icon for a pump toggles
between not installed and installed.
7. Press System Setupto return to the System Setup screen.
24-Pump, 128-Station Controller
Chapter 3: Installation
37
Download from Www.Somanuals.com. All Manuals Search And Download.
8. The new setting appears under System Parameterson the System Setup screen.
Setting the Date/Time
You can set the current date and time by going to the System Setup screen and pressing Set
Time & Date.
1. To set the time, touch Hour. A keypad will pop up and you will be able to enter the
current hour. The controller uses military time. You can repeat this process for the
minutes by pressing Minute.
2. To set the date, touch Month. A keypad will pop up for you to enter the number of the
current month (i.e. May = 5). You can repeat this process to set the current day and year
by pressing Dayand Year, as appropriate. Use ← to erase any mistakes. Use ↵ to enter
the value.
The keypad disappears and the new setting appears under Set Time &
Date.
Naming Purge Valves and Materials
You can assign purge valves and materials names rather than keep them assigned by
numbers. (You can name stations and pumps as well. Refer to the “Setting Up Stations” and
“Setting Up Pumps” sections later in this chapter).
1. Go to the System Setup screen and touch Name Purge Vlv/Materialand scroll
through the list of purge valve/materials and find the one you want to rename.
2. Use the up and down arrows to select the purge valve/material you would like to name.
3. Select Press to Changeat the bottom of the list.
A keypad will pop up.
3. You can then type in a name of up to eight alpha-numeric characters. Make sure to choose
different names, as the system does not recognize duplicate names. Use ← to erase any
mistakes. Use ↵ to enter the value.
Checking Addressing and Wiring for System Components
Once you have set the number of stations and pumps as described previously, you should
verify that the controller is communicating with all stations, pumps, and central alarms, and
with the ArmorBlocks for all central purge valves. To do so:
1. At the System Setup screen, touch DeviceNet Nodes on the right side of the
screen.
The DeviceNet Status screen appears:
24-Pump, 128-Station Controller
Chapter 3: Installation
38
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Check that the expected components are shown as present (green) and not present
(grey). (Disregard any error messages.)
For example, if you have 18 stations, boxes 01through 18in the Stationssection
should be green and boxes 19through 128should be grey. For central purge valves,
you should see a green box for each ArmorBlock installed.
If the screen display is not as expected, either a component’s ArmorBlock has an incorrect
address or the ArmorBlock is not correctly wired to the network.
When you have verified that the controller is communicating with the other system
components, you should verify that the inputs on all ArmorBlocks for stations and pumps are
wired correctly and are working correctly. To do so:
Station numbers are stacked vertically as column headings in this screen.
3. Check that all inputs are on (green) or off (grey) as expected and that they switch on
and off as required:
a. Station demand switch: In a new installation, the box labeled Demand
Switchshould be green for every station (vacuum hopper) in the system.
(All other boxes for demand switches will be grey.) In a retrofit at an existing
installation, each station’s Demand Switchbox should be green unless the
receiver bin under the station is in fact full.
b. Option input: The proper status of this input will be dictated by the option
installed.
If any input does not operate as expected, check the wiring on the ArmorBlock. If this does
not solve the problem, phone the Service Department for assistance.
Setting Up Alarm Silences
When an alarm occurs, a horn sounds and a strobe light flashes at each installed central
alarm. An alarm window will also appear in the center of the operator interface screen(s).
The window will display a description of the alarm, the time and date it occurred, and a
Push To Silence button. Touching this button silences the horn(s) and turns off the
light(s) for configurable periods of time. You can set different lengths of time for keeping the
horn silent and keeping the light turned off. If a new alarm occurs, the horn sounds and the
light turns on again.
To set the lengths of time for suppressing the alarm strobe and horn:
1. Go to the System Setup screen. To reach this screen from any other screen, touch
System Setupon the right-hand side of the screen
24-Pump, 128-Station Controller
Chapter 3: Installation
39
Download from Www.Somanuals.com. All Manuals Search And Download.
The current settings are displayed under Alarm Strobe Suppressionand
Alarm Horn Silence.
2. Touch Alarm Strobe Suppression or Alarm Horn Silence, as appropriate.
A keypad pops up, with the current setting.
3. Enter the number of minutes you want the horn or light to be turned off once the
alarm silence button is pushed (range: 0–99). If the alarm condition is not corrected
or the defective device is not disabled through the touch screen, the audible and
visual alarms will reoccur after the times expire. If you want the light (or the horn) to
stay on as long as the alarm persists, simply press 0. If you want the horn (or the
light) to stay off until a new alarm occurs, use 99 for its entry. Use ← to erase any
mistakes. Use ↵ to enter the value.
The keypad disappears and the new setting appears under Alarm Strobe
Suppressionor AlarmHorn Silence.
4. Repeat for the other device (strobe or horn) as appropriate.
Setting Up Pump Staging
To avoid an excessive power demand at your facility when the conveying system starts up,
you can stagger the times at which pumps start. Whenever a demand would cause two pumps
to start simultaneously, your choice for pump staging sets the delay between the start of one
pump and the start of the next. The factory default is a delay of five seconds. You need to
change this setting only if this delay is too long or too short for your facility.
To set the delay between the start of one pump and the next:
1. Go to the System Setup screen if needed.
The current delay is displayed under Pump Staging.
2. Touch Pump Staging.
A keypad pops up, with the current setting.
3. Enter the number of seconds (range: 0–99). Use ← to erase any mistakes. Use ↵ to
enter the value.
The keypad disappears and the new setting appears under Pump Staging.
24-Pump, 128-Station Controller
Chapter 3: Installation
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Up Stations
Before starting the system, you must define several settings for each station, such as which
pump conveys material to it and whether the station has a slide gate. This section first
discusses how to use the controller’s menu system to configure stations. The table on pp. 64–
68 discusses the individual choices.
Setting Up a Single Station
1. Go to the Station Status screen if needed.
To reach this screen from any other screen, touch Stationson the right-hand side
of the screen. The Station Status screen appears. Depending on which model you
have, your screen will appear as one of the following:
2. Touch the icon for the station you want to set up, and hold it for several seconds.
The Station n Operator Settings screen for the selected station appears:
Touch StationSetupat the Station n Operator Settings screen.
The Station n Setup screen appears:
24-Pump, 128-Station Controller
Chapter 3: Installation
41
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Touching Helpin the lower right of this screen gives you a menu of online help for
the choices in this screen.
4. Adjust settings as required. Touching any box that appears in red (for “disabled”)
toggles it to green (for “enabled”). Many boxes have more than one embedded state.
Touching any box that appears in light gray gives you a keypad to enter a new value.
Keypad entry works as with many ATM machines: the first digit you enter initially
appears in the rightmost column and moves to the left as you enter more digits. Use
← to erase any mistakes. Use ↵ to enter the value. The keypad disappears and the
Station n Setup screen shows the new value in the selected gray box.
Touching Reset To Defaultsin the lower right of the screen changes all
settings for this station back to their factory defaults.
See pp. 64–68 for details on the options and their default settings.
4. As appropriate:
a. Copy this station’s settings to one or more other stations, as described below
- or -
b. Touch Back◄ to go to the Station n-1 Setup screen
- or -
c. Touch Next► to go to the Station n+1 Setup screen
- or -
d. Touch Gotoand enter a station number to go to that station’s setup screen
5. To save or restore settings, go to the System Setup screen and touch
Save/Restore on the right side of the screen.
Naming Stations
To name a station, go to the Station Status screen. Touch the icon for the station you
want to name and hold it for several seconds.
The Station n Operator Settings screen for the selected station appears.
Touch Station Setup at the Station n Operator Settings screen.
The Station n Setup screen appears.
1. Press Name Line 1at the bottom of the Station n Setup screen.
A keypad will pop up.
24-Pump, 128-Station Controller
Chapter 3: Installation
42
Download from Www.Somanuals.com. All Manuals Search And Download.
2. You can enter a name of up to four (4) alpha-numeric characters. If you would like
to enter a longer name, you can go back to the Station n Setup screen and press
Name Line 2 to repeat the process. Using Name Line 2 will allow you to
enter up to four (4) more alpha-numeric characters, for a total of eight (8) characters.
The characters will appear as two four-digit names on two separate lines.
Use ← to erase any mistakes. Use ↵ to enter the value.
Note: Make sure to choose different names, as the system does not recognize
duplicate names.
3. You can scroll through the stations by scrolling through Back and Next at the top
of the screen.
Copying Settings from One Station to Others
If other stations at your facility will use the same settings as a station you have already set up,
you can copy the settings from this station to the others. To do so:
1. At the Station n Setup screen (for the station you want to copy from), touch Copyin
the screen’s upper right.
The Station Copy screen appears, showing the station number for the station you are
copying from:
2. Follow the directions on the following pages to copy settings to one other station, a
range of stations, or all stations.
To copy the selected station’s settings to one other station
1. Touch the gray Copy to Stationbutton next to the green button labeled Copy
To Single Station.
The keypad pops up.
2. Enter the station number for the station you are copying to. Use ← to erase any
mistakes. Use ↵ to enter the value.
The keypad disappears and the Station Copy screen shows the station number you
entered under Copy to Station.
3. Touch the green Copy to Single Stationbutton.
“Copy Complete” briefly appears at the top of the screen.
24-Pump, 128-Station Controller
Chapter 3: Installation
43
Download from Www.Somanuals.com. All Manuals Search And Download.
4. As appropriate, either continue copying to other stations, or touch Station Setup
to go back to the Station n Setup screen.
To copy the selected station’s settings to a range of other stations
1. Touch First Station button next to the green button labeled “Copy to Range
of Stations.”
The keypad pops up.
2. Enter the station number for the hopper at the lower end of the range you are copying
to. Use ← to erase any mistakes. Use ↵ to enter the value.
The keypad disappears and the Station Copy screen shows the station number you
entered under First Station.
3. Touch Last Stationbutton next to the light grey button labeled First
Station.
The keypad pops up.
4. Enter the station number for the hopper at the upper end of the range you are copying
to. Use ← to erase any mistakes. Use ↵ to enter the value.
The keypad disappears and the Station Copy screen shows the station number you
entered under Last Station.
5. Touch the green CopyTo Range of Stations button.
“CopyComplete” briefly appears at the top of the screen.
6. As appropriate, either continue copying to other stations, or touch Station Setup
to go back to the Station n Setup screen.
To copy the current station’s settings to all other stations
1. Touch the green CopyTo All Stationsbutton.
“CopyComplete” briefly appears at the top of the screen.
2. Touch Station Setupto go back to the Station n Setup screen.
Setting Up Pumps
Before starting the system, you must define several settings for each pump, such as how
quickly to shut it down when it is not in use and whether the pump has a local alarm. This
section first discusses how to use the controller’s menu system to configure pumps. The table
on page 77 discusses the individual choices.
Setting Up a Single Pump
1. Go to the Pump Status screen.
To reach this screen from any other screen, touch Pumpson the right side of the
screen. The Pump Status screen appears:
24-Pump, 128-Station Controller
Chapter 3: Installation
44
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Touch the icon for the pump you want to set up, and hold it for several seconds.
The Pump n Setup screen appears:
3. Touching Helpin the lower right of this screen gives you a menu of online help for
the choices in this screen.
4. Adjust settings as required. Touching any box that appears in red (for “disabled”)
toggles it to green (for “enabled”), and vice versa. Touching any box that appears in
light gray gives you a keypad to enter a new value.
Keypad entry works as with many ATM machines: the first digit you enter initially
appears in the rightmost column and moves to the left as you enter more digits. Use
← to erase any mistakes. Use ↵ to enter the value. The keypad disappears and the
Pump n Setup screen shows the new value in the selected gray box.
See page 64 for details on the options and their default settings.
5. As appropriate:
a. Copy this pump’s settings to one or more other pumps, as described below
—or—
b. Touch Back◄ to go to the Pump n-1 Setup screen
—or—
24-Pump, 128-Station Controller
Chapter 3: Installation
45
Download from Www.Somanuals.com. All Manuals Search And Download.
c. Touch Next► to go to the Pump n+1 Setup screen
—or—
d. Touch Gotoand enter a pump number to go to that pump’s setup screen
5. To save or restore settings, go to the System Setup screen and touch
Save/Restore on the right side of the screen.
Naming Pumps
To name a station, go to the Pump Status screen. Touch the icon for the pump you
want to name and hold it for several seconds.
The Pump n Operator Settings screen for the selected pump appears.
Touch Pump Setup at the Pump n Operator Settings screen.
The Pump n Setup screen appears.
3. Press Pump Nameat the bottom of the Pump n Setup screen.
A keypad will pop up.
6. You can enter a name of up to eight (8) alpha-numeric characters. Use ← to erase
any mistakes. Use ↵ to enter the value.
Note: Make sure to choose different names, as the system does not recognize
duplicate names.
6. You can scroll through the pumps by scrolling through Back and Next at the top
of the screen.
Copying Settings from One Pump to Others
If other pumps at your facility will use the same settings as a pump you have already set up,
you can copy the settings from this pump to the others. The station name will not be copied.
To copy settings from one pump to others:
1. At the Pump n Setup screen (for the pump you want to copy from), touch Copyin
the screen’s upper right.
The Pump Copy screen appears, showing the pump number for the pump you are
copying from:
2. Follow the directions below to copy settings to one other pump, a range of pumps, or
all pumps.
24-Pump, 128-Station Controller
Chapter 3: Installation
46
Download from Www.Somanuals.com. All Manuals Search And Download.
To copy the selected pump’s settings to one other pump
1. Touch the gray Copy to Pumpbutton next to the green Copy To Single
Pump button.
The keypad pops up.
2. Enter the pump number for the pump you are copying to. Use ← to erase any
mistakes. Use ↵ to enter the value.
The keypad disappears and the Pump Copy screen shows the pump number you
entered under Copy to Pump.
3. Touch the green CopyTo Single Pump button.
“CopyComplete” briefly appears at the top of the screen.
4. As appropriate, either continue copying to other pumps, or touch Pump Setupto
go back to the Pump n Setup screen.
To copy the selected pump’s settings to a range of other pumps
1. Touch First Pumpnext to the green button labeled Copy To Range of
Pumps button.
The keypad pops up.
2. Enter the number for the pump at the lower end of the range you are copying to. Use
← to erase any mistakes. Use ↵ to enter the value.
The keypad disappears and the Pump Copy screen shows the pump number you
entered under First Pump.
3. Touch Last Pumpnext to the light grey button labeled First Pump.
The keypad pops up.
4. Enter the number for the pump at the upper end of the range you are copying to. Use
← to erase any mistakes. Use ↵ to enter the value.
The keypad disappears and the Pump Copy screen shows the pump number you
entered under Last Pump.
5. Touch the green Copybutton labeled Copy To Range of Pumps.
“CopyComplete” briefly appears at the top of the screen.
6. As appropriate, either continue copying to other pumps, or touch Pump Setupto
go back to the Pump n Setup screen.
To copy the current pump’s settings to all other pumps
1. Touch the green CopyTo All Pumps button.
“CopyComplete” briefly appears at the top of the screen.
2. Touch Pump Setupto go back to the Pump n Setup screen.
24-Pump, 128-Station Controller
Chapter 3: Installation
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Finishing Setup: Setting Up Passwords
You can set up passwords for two levels of security: for operators and for setup personnel.
The controller comes from the factory with neither password set. This allows every user
access to all functions.
Setup Password. If you define a password for setup personnel, then most settings can be
changed only after entering the password. The password will be required to display the
following screens:
• System Setup (to review and change system-wide settings and go to
the network status screens)
• Station Setup (to review and change settings for all station options)
• Pump Setup (to review and change settings for all pump options)
Operator Password. If you define a password for operators, then a password will be
required to carry out any function (other than reviewing station and pump status, silencing
alarms, reviewing the alarm log, and looking at help screens). Entering the operator’s
password will give the user access to the functions at the following screens:
• Station Status (to enable or disable a station, and start or stop system)
• Pump Status (to enable or disable a pump, and start or stop system)
• Station n Operator (to adjust a station’s convey time and dump delay,
activate priority convey, and review the station’s last convey time and
pump assignment; depending on the options installed, the screen may
also enable the operator to adjust the mixture percentage for a remote
proportioning valve, change the purge time and purge valve, and set
the intended material line for manifold sharing)
Entering the setup password will give the user access to all functions.
To set (or remove) password protections:
1. Press System Setupon the right side of the screen to go to the System Setup
screen if needed.
The System Setup screen appears:
The current passwords are displayed under Operator Passwordand Setup
Password. No value means that no password is required.
24-Pump, 128-Station Controller
Chapter 3: Installation
48
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Touch Operator Password or Setup Password, as appropriate.
A keypad pops up.
3. Enter up to eight (8) alpha-numeric characters. If you want to remove the password
protection, simply leave the entry blank. Use ← to erase any mistakes. Use ↵ to enter
the value.
The keypad disappears and the new setting appears under Operator (or Setup)
Password. In addition, if you have added a password, a new button appears on the
screen, labeled Log Off Operator.
If desired, you can also change the duration for which a password remains effective. During
operation, the password-protected screens are available either until the user logs off or until
this time elapses, whichever comes first. This feature prevents the password from remaining
active if a user forgets to log off.
4. The password timer starts when the user logs on. It expires even if the user is actively
using the screens when the chosen time is up. If the timer expires, the system goes to
the Station Status screen. Your password duration should be long enough to allow
authorized users to complete their tasks but short enough to provide adequate
protection against tampering.
To change the duration of a password:
1. At the System Setup screen, touch Operator Password Durationor Setup
Password Duration, as appropriate.
A keypad pops up, with an entry of the current setting.
2. Enter the number of minutes (range: 2–99). Use ← to erase any mistakes. Use ↵ to
enter the value.
The keypad disappears and the new setting appears under Operator (or Setup)
Password Duration.
Save/Restore Settings
To save settings, go to the System Setup screen and touch Save/Restore on the right
side of the screen. Touch Save Settings. When the settings have been saved, the
controller will display “Save Complete.” The date and time will appear under “Restore
Settings.”
To restore old settings, touch Save/Restore. Touch Restore Settings. The
controller will display the most recent date and time that the settings were restored.
24-Pump, 128-Station Controller
Chapter 3: Installation
49
Download from Www.Somanuals.com. All Manuals Search And Download.
3-6 Initial Startup
Once you have finished all the setup described above, you are ready to start the system. To do
so:
1. At any screen, touch Stationson the right-hand side of the screen.
The Station Status screen appears.
2. For each station that you want to use, briefly touch its icon.
The icon turns blue, indicating that the station is ready or yellow, indicating that the
station needs material.
3. Touch Pumps.
The Pump Status screen appears.
4. For each pump that you want to use, briefly touch its icon.
The icon turns blue, indicating that the pump is ready.
5. Touch Push to Start Systemin the lower right-hand corner of the screen.
The system starts. If any alarm messages appear on the top of the screen, see Section
3-5 on page 62.
24-Pump, 128-Station Controller
Chapter 3: Installation
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Operation
4-1 Overview
Your 24/128 controller electrically controls valves and solenoids to convey material from a
central location to individual stations as needed. The controller senses demands for material
at the stations and responds to the demands in a timely fashion.
This section gives the procedures for using your controller, and it covers tasks that can be
carried out with no password or with an operator’s password. The section is divided into four
sub-sections:
• Starting and stopping the system
• Basic tasks: tasks normally carried out by a station operator
• Advanced tasks: tasks normally carried out by setup personnel
• Alarms: silencing and clearing alarms
Before you carry out any of the procedures in this chapter, the system must be set up as
described in the previous chapter.
4-2 Starting and Stopping the System
In an emergency, you can use the power switch on the upper right-hand side of the controller
cabinet if a password is required to stop the system and you do not know the password.
Normally, all the stations and pumps you want to use should be enabled before
you start the system. When the system is stopped, icons for enabled stations are
blue when full and dark yellow when they need material. Icons for enabled
pumps are blue. Enabling stations and pumps is described on p. 55.
A button to start and stop the system is located in the lower right of the Station Status, Pump
Status, and Alarm Log screens. When the system is off, the button is red and reads Push to
Start System. When the system is on, the button is green and reads Push to Stop
System. Depending on the setup at your facility, the system may prompt for a password
when you touch this button.
If conveying does not begin when you start the system, check to make sure that all needed
pumps are enabled. If they are, check that all needed stations are enabled.
24-Pump, 128-Station Controller
Chapter 4: Operation
51
Download from Www.Somanuals.com. All Manuals Search And Download.
4-3 Basic Tasks
This section covers tasks that can be carried out with no password or with an operator’s
password.
Reviewing Station Status
The starting point for all operations is the Station Status screen. To reach this screen from any
other screen:
1. Touch Stations.
The Station Status screen appears. Depending on which model you have, your screen
will appear as one of the following:
The status of each station is color-coded, as summarized in the upper right of the screen.
You can see an explanation of each status by using the online help. To do so from this screen:
2. Touch anywhere in the rectangle in the upper right of the screen or the Helpbutton
on the lower right side of the screen.
The Help Menu appears.
3. In the section of the Help Menu labeled Screen Symbols/Colors, touch
Station.
The Station Symbols help screen appears, explaining the status represented by each
color.
4. When you are finished reviewing the information, touch Stations(or Pumps).
The Station Status (or Pump Status) screen appears.
24-Pump, 128-Station Controller
Chapter 4: Operation
52
Download from Www.Somanuals.com. All Manuals Search And Download.
The following table explains the status represented by each color at the Station Status screen.
Color
Label
Description
Silver
Offline
Station is not enabled. The controller ignores any demands or
alarms.
Blue
Ready
Station is enabled and idle (full).
Dark Yellow
Light Green
Brown
Demand
Purging
Dumping
Blow Back
Station requires material.
The material line is being purged of material.
The station is dumping material into its receiver.
Station’s air filter is being cleaned by blowing compressed air
backward through it.
White
Dark Grey
Bypass
Bypass switch at the station has been turned on, disabling the
station.
Medium
Green
Orange
Red
Priority
Convey
Alarm
Station is in priority convey mode. Its pump will be temporarily
dedicated to filling it as soon as possible.
Station is in alarm.
Station is in critical alarm. The controller has disabled the station
until the alarm is cleared.
Critical
Purple
Closed
Loop
Station is in closed loop convey.
Light Yellow
Dark Green
Waiting
Convey
Station is waiting for material to become available.
Station is being loaded.
Additional basic information about each station (convey time, dump delay, pump assignment,
and, if enabled, RPV setting, purge settings, etc.) is available at the Station n Operator screen.
See page 56 for details.
Detailed configuration settings for each station are available at the Station n Setup screen. See
page 39 for details.
Reviewing Pump Status
The Pump Status screen is the counterpart of the Station Status screen. To reach the Pump
Status screen from any other screen:
1. Touch Pumps.
The Pump Status screen appears:
The status of each pump is color-coded, as summarized in the upper right of the screen.
You can see a more detailed explanation of each status by using the online help. To do so
from this screen:
24-Pump, 128-Station Controller
Chapter 4: Operation
53
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Touch anywhere in the rectangle in the upper right of the screen or the Helpbutton
on the lower right side of the screen.
The Help Menu appears.
3. In the section of the Help Menu labeled Screen Symbols/Colors, touch Pump.
The Pump Symbols help screen appears, explaining the status represented by each
color.
4. When you are finished reviewing the information, touch Pumps (or Stations).
The Pump Status (or Station Status) screen appears.
The following table explains the status represented by each color at the Pump Status screen.
Color
Silver
Blue
Label
Offline
Ready
Description
Pump is not enabled. The controller ignores any alarms.
Pump is off, waiting for demand from a station.
Pump is on, waiting for demand from a station. If there is no
demand before the end of the auto shutdown delay, the pump
will turn off.
Light Green Idle
Green
White
Loading
Cleaning
Pump is conveying material to a station.
Pump’s air filter is being cleaned by blowing compressed air
backward through it.
Orange
Red
Alarm
Critical
Pump is in alarm.
Pump is in critical alarm. The controller has disabled the pump
until the alarm is cleared.
Light Yellow Waiting
Pump is waiting for material to become available.
Additional information about each pump, including configuration settings and the number of
hours the pump has been running, is available at the Pump n Setup screen. For details on
configuration settings, see page 42. For details on the hour meter, see page 59.
Logging On and Logging Off
Your controller may be set up to require a password for any operation (other than reviewing
station and pump status, silencing alarms, reviewing the alarm log, and looking at help
screens). If so, a password entry screen will appear:
Press the Enter Passwordbutton. A keypad will appear:
24-Pump, 128-Station Controller
Chapter 4: Operation
54
Download from Www.Somanuals.com. All Manuals Search And Download.
• Enter the alphanumeric password.
Each digit appears as an “*” as you touch it. Press ↵ when complete.
If you have lost the password(s), contact the manufacturer for assistance.
Once you have logged on, the password remains active until you log off or the password
expires. (Setup personnel at your facility control the number of minutes before the password
expires.) While the password is active, you can continue to carry out password-protected
tasks without reentering the password. If the timer expires, the controller goes to the Station
Status screen and you must reenter the password to continue working.
When you have finished any tasks that require the password, you should log off. (If you
forget to do this, the controller will log you off when the password expires.) To log off:
1. Go to System Setup.
2. Touch Log Off on the right of the screen.
The Station Status screen appears.
Enabling and Disabling Stations and Pumps
When a station or pump is disabled, the controller does not attempt to use it and ignores any
alarms that occur for it. Disabling a station or pump at the controller’s screen is similar to
bypassing a station with its bypass switch. Enabling a station or pump makes it available for
use. (For a station to be available for the system, it must be enabled at the controller’s screen
and its bypass switch [if present] must be in the “0” position.)
To enable or disable a station (or pump):
1. Go to the Station Status (or Pump Status) screen, if needed.
To reach this screen from any other screen, touch Stations(or Pumps) on the
right-hand side of the screen.
Each disabled station (or pump) has an icon with a status of “offline” (silver). All
other statuses are enabled statuses.
2. Touch the icon for the station (or pump) briefly.
The station (or pump) switches to the new state, as indicated by the color of its icon.
3. If the Station n Operator (or Pump n Setup) screen appears when you touch the icon,
then you have kept your finger on the screen too long. Touch Stations(or
Pumps) to return to the Status screen and try again.
24-Pump, 128-Station Controller
Chapter 4: Operation
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Reviewing and Adjusting Basic Station Settings
Reaching and Reading the Station Operator Screens
The 24/128 Controller has a Station Operator Settings screen for each station, as shown
below. This screen enables you to review and adjust all basic settings for the station.
To reach the Station n Operator screen:
1. Go to the Station Status screen, if needed.
To reach this screen from any other screen, touch Stationson the right-hand side
of the screen.
2. Touch and hold the icon for the station, until the controller either prompts for the
password or displays the Station n Operator screen.
Once you have entered the password (if needed), the Station n Operator screen
appears:
Settings in the box labeled Convey, the red Priority Convey Activatebutton, and
the menu controls on the right-hand side of the screen appear for all stations. The other
options in this screen appear if and only if the station has these features enabled.
Buttons in light gray are settings that you can adjust at this screen. Boxes in dark gray are for
display only. If a pump assignment or purge setting needs to be changed, this must be done at
the Station n Setup screen.
Navigating among the Station Operator Screens
The controls in the upper right-hand corner of the screen enable you to move among the
Station Operator screens:
1. To display the screen for the next lower-numbered station (for example, to move
from the screen for Station 15 to the screen for Station 14), touch ◄ Back.
2. To display the screen for the next higher-numbered station (for example, to move
from the screen for Station 15 to the screen for Station 16), touch Next►.
3. To display the screen for a specific station, touch Goto. A keypad pops up. Enter the
number for the desired station. Use ← to erase any mistakes. Use ↵ to enter the
value.
4. To exit to the Station Status (or Pump Status) screen, touch Stations(or Pumps).
24-Pump, 128-Station Controller
Chapter 4: Operation
56
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting Convey Time and Dump Delay
Convey time is the length of time the station’s vacuum valve remains open to allow material
to be drawn in. (For a volume-fill station, the valve closes when material covers the station’s
volume-fill proximity sensor or this time elapses, whichever comes first.)
Dump delay is the length of time allowed for material to drain from the station into its
receiver. During this time, the controller does not attempt to deliver any more material to the
station.
The settings for convey time and dump delay should match the times actually required to fill
and empty the station. The following problems may occur if these settings are incorrect:
1. Material is backing up and causing “high vacuum” alarms (for time-fill stations
only): Convey time is too long.
2. System is not keeping up with the demand for material: Convey time is too short, or
dump delay is too long.
For your reference, the Station n Operator screen shows the length of time the controller
actually spent conveying material during the most recent delivery under Last Convey
Time.
To adjust a station’s convey time (or the dump delay):
1. Go to the Station n Operator screen (as described on p. 56), or go to the Station n
Setup screen.
2. Touch Convey Time (or Dump Delay).
A keypad pops up.
3. Enter the number of seconds desired. Use ← to erase any mistakes. Use ↵ to enter the
value.
The new setting appears under Convey Time(or Dump Delay).
4. If you change convey time by more than a few seconds for a station with a remote
proportioning valve (RPV), notify the setup personnel at your facility. The setting for
the RPV’s cycle time should be adjusted to divide evenly into the new convey time
(see page 41).
Activating and Stopping Priority Convey for a Station
Before activating priority convey, make sure that all other stations using the same pump have
adequate material in reserve to continue operation. No material will be conveyed to these
stations during priority convey.
If you want the controller to fill a specific station with material immediately, you can activate
“priority convey” for that station. When you do so, the controller temporarily dedicates the
station’s pump to it, ignoring demands from other stations assigned to that pump. Once the
chosen station is full, normal operation resumes.
You can also use this feature to give one station a “head start” by conveying a few loads to it
and then stopping the priority convey.
No more than one station for a given pump can be in “priority convey” at once.
To activate priority convey:
Go to the Station n Operator screen (as described on p. 56), or go to the
Station n Setup screen.
24-Pump, 128-Station Controller
Chapter 4: Operation
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Touch Priority Convey Activate.
The button changes to Priority Convey Activeand blinks until the station’s
demand has been satisfied (or you stop the priority convey).The controller begins
filling the chosen station only (after finishing any convey already in progress).
To stop a priority convey before the station is completely full:
Touch the blinking Priority Convey Active.
The button changes to Priority Convey Activateand stops blinking. The
controller finishes the current convey, if any, and resumes normal operation.
Changing the Mixture for a Remote Proportioning Valve
A remote proportioning valve (RPV) mixes two different materials, typically virgin and
regrind materials, during a convey cycle. If present, this valve may be set up so that you
control the mix with a timer at the station, or it may be set up so that you control the mix with
the controller’s touch screen. The instructions here apply only for controlling the mixture
from the touch screen.
The controller refers to the two materials as Material A (primary) and Material B (additive).
The system is set up so that, if there are any inaccuracies in the proportions, the mix will
contain more Material A and less Material B.
To change the mixture for the remote proportioning valve:
1. Go to the Station n Operator screen (as described on page 56), or go to the Station n
Setup screen.
2. Touch RPV Material B.
A keypad pops up.
3. Enter the desired percentage for the additive material. Use ← to erase any mistakes.
Use ↵ to enter the value. The new setting appears under RPV Material B.
24-Pump, 128-Station Controller
Chapter 4: Operation
58
Download from Www.Somanuals.com. All Manuals Search And Download.
4-4 Advanced Tasks
This section describes the procedures carried out during operation that are normally reserved
for setup personnel. These procedures require use of the setup password (if your facility has
defined one). The procedure for logging on with the setup password is the same as for
logging on with the operator password; see page 45. Logging off is also the same, except that
operators can log off only at the Station n Operator screen, while most screens accessible to
setup personnel offer Log Offas an option.
You can also change the setup for stations, pumps, and the system during operation. See
Chapter 4, “System Setup,” for information on the procedures and options.
Reviewing and Resetting a Pump Hour Meter
The controller keeps two meters for the length of time a pump has run. One, like a car’s
odometer, keeps a running total and cannot be reset. The other, like a car’s trip odometer,
counts the running time since the last reset.
To review and reset the hour meter:
1. At any screen, touch Pumps.
The Pump Status screen appears.
2. Touch and hold the icon for the pump.
The Pump n Setup screen appears:
The box labeled x Hours (Resetable)shows the running time since the last
reset. The box labeled x Hours shows total running time.
3. To reset the resettable meter, touch Hour Meter Reset.
The time above Hours (Resetable)changes to 0.
Transferring Stations to a Standby Pump
If a pump fails, you can transfer all of the controller’s station assignments for that pump to a
standby pump. To do this, you must disable (take offline) both the source pump and the
standby pump, and the standby pump must have no stations already assigned to it.
The transfer operation at the controller’s touch screen merely changes the pump assignment
for every station on the failed pump. It does not transfer any pumps settings for auto
24-Pump, 128-Station Controller
Chapter 4: Operation
59
Download from Www.Somanuals.com. All Manuals Search And Download.
shutdown delay, alarms, or blowback to the standby pump. Mechanical connections must be
changed manually.
To transfer stations from a pump to a standby pump:
1. At any screen, touch Pumps.
The Pump Status screen appears.
2. Both the source pump and the standby pump must be offline. If either pump is any
other state, disable it by touching its icon briefly.
The icon becomes greny.
3. Move the vacuum hose from the failed pump to the standby pump, and carry out any
other mechanical procedures needed to use the standby pump.
4. At the Pump Status screen, touch and hold the icon for any pump until the Pump n
Setup screen appears.
5. At the Pump n Setup screen, touch Transfer Stations To Standby Pump.
The Transfer to Standby Pump screen appears:
6. Touch Source Pump.
A list of available pumps pops up.
7. Scroll through the list to choose a source pump. Press Return once you have selected
and highlighted your desired source pump.
The number appears under Source Pump.
8. Touch Destination Pump.
A list of available pumps pops up.
9. Scroll through the list of pumps to choose a destination pump. Press Return once you
have selected and highlighted your desired destination pump.
The number appears under Standby Pump, and a button labeled Press to
Move Stationsappears on the screen:
24-Pump, 128-Station Controller
Chapter 4: Operation
60
Download from Www.Somanuals.com. All Manuals Search And Download.
10. When you enter the second pump number, the controller checks to make sure that
both pumps are offline and that the standby pump has no stations assigned to it. If
these conditions are not all met, error messages appear on the screen instead of a
Press To Move Stationsbutton. If you get an error message, first check to
make sure that you have entered the correct numbers and reenter if necessary.
If the error message tells you to disable the source pump and/or the standby pump, touch
Returnat this screen, then Pumpsat the Pump n Setup screen. Take the pumps offline and
then return to the Transfer to Standby Pump screen.
If the error message tells you that the standby pump has stations assigned, you must either use
a different standby pump or you must remove the pump assignment for all stations assigned
to the standby pump. To remove the assignments, touch Returnat this screen, then
Stationsat the Pump n Setup screen.
Hold a station icon to go to its Station Operator screen, then touch Setup to go to the Station n
Setup screen. Use ◄ Back. and Next ► to review all pump assignments and, where
necessary, choose Assigned to Pump xto set station assignments to 0 (unassigned).
Then return to the Transfer to Standby Pump screen.
1. Touch Transfer To Standby Pump.
“Transfer in Progress” appears briefly on the screen, followed by “Transfer
Complete,” in place of the Transfer To Standby Pumpbutton. The controller
switches the setting for Source Pumpto the new pump and switches the setting for
Standby Pumpto 0 (unassigned).
2. Touch Return.
The Pump n Setup screen appears.
3. Touch Pumps.
The Pump Status screen appears.
4. Put the standby pump online by briefly touching its icon.
The icon changes color to show the new status, and the system begins using the
pump. In addition, all Station n Operator and Setup screens show the new pump
assignment.
When the failed pump is operational again, you can repeat this process, this time using the
standby pump’s number as the setting for Source Pumpthe repaired pump’s number as the
setting for Standby Pump.
24-Pump, 128-Station Controller
Chapter 4: Operation
61
Download from Www.Somanuals.com. All Manuals Search And Download.
3-5 Alarms
Reviewing Alarms
At the Station Status or Pump Status screen:
1. Touch Alarms.
The Alarm Log screen appears, with the newest alarm listed first:
To scroll up and down through the list:
• Touch ▲ and ▼ at the bottom of the list.
Silencing Alarms
Whenever a new alarm occurs, your controller sounds the horn and turns on the strobe light at
each central alarm. If the alarm is for a specific station or pump, and if the station or pump
has a local alarm, the controller also turns on the local alarm light. In addition, a banner
appears on the touch screen displaying an alarm message and a Push To Silencebutton.
To silence the alarm:
1. Touch Push to Silenceon the alarm banner.
The horns and lights at the central alarms turn off. (The local alarm light stays on.)
The banner will close. Your controller has separate, configurable settings for how
long the horns should remain silent and how long the lights should remain off. If the
alarm condition still exists when either of these times elapses, the corresponding
devices (horns or lights) turn on again. If a new alarm occurs, both the horns and the
lights turn on.
24-Pump, 128-Station Controller
Chapter 4: Operation
62
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5: Maintenance
5-1 Preventative Maintenance
No preventative maintenance is required on this unit.
5-2 Corrective Maintenance
Network Scanner Module Considerations
The manufacturer includes a network scanner software diskette with your controller; this
diskette and instructions are located in your Customer Information Packet. Keep this diskette
and the instructions in a safe place.
Should the network scanner module require replacement, use the scanner software to restore
the program. You can:
• Purchase a programmed replacement scanner module from the
manufacturer
• In extreme cases, you can purchase the module from your local Allen-
Bradley dealer and program it yourself with the scanner software
diskette; you can also have your A-B dealer do that for you
We suggest that you have a preprogrammed spare network scanner module on hand for such
conditions.
24-Pump, 128-Station Controller
Chapter 5: Maintenance
63
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6: Configurable Settings
This section describes the proper setup of the 24-pump 128-station control system
parameters. These parameters are operator changeable; however, these items should require
setup only during the initial installation. Only authorized personnel should change them.
Many of the variables and setup parameters have been preset at the factory and do not need to
be changed. However, this section of the manual will address all of the setup parameters that
were available at the time of printing. The purpose of this is to familiarize the reader with all
the setup parameters and their usage.
6-1 Memory Module Considerations
The operator interface and the PLC central processing unit use memory modules to store the
operating program and user settings. The module is installed in the front of the PLC CPU
card.
The memory module returns the controller to the factory default settings if an electrical fault
occurs, or if the hardware is replaced. Keep in mind that this condition is extremely rare.
You will then need to restore saved settings or set up the controller once again with the
settings you programmed in this chapter.
6-2 Options for Station Setup
Name
Description
Options
Default
Conveying Options
Convey time
Length of time the station’s vacuum valve
remains open to allow material to be drawn in.
(For a volume-fill station, the valve closes when
material covers the station’s volume-fill
proximity sensor or this time elapses, whichever
comes first.)
0–999.9 sec. 30 sec.
Adjust this value to match the actual time
needed to fill the station.
(Last convey time)
Dump delay
Display only. Length of time the station’s
vacuum valve was open for receiving material
during the most recent convey. This information
is displayed for your reference when adjusting
convey time and dump delay.
Length of time allowed for material to drain from 3–99 sec.
the station into the receiver. The controller will
not attempt to deliver more material to the
station until this time has elapsed.
—
—
10 sec.
Adjust this value to match the actual time
needed to drain the station. If it is set too short,
the controller may attempt to refill the station
before it is empty, causing material to back up
and/or underusing the station’s capacity. If it is
set too long, the system may be unable to keep
up with your equipment’s demand for material.
24-Pump, 128-Station Controller
Chapter 6: Configurable Settings
64
Download from Www.Somanuals.com. All Manuals Search And Download.
Name
Description
Options
Default
Conveying Options
Assigned to pump n
Name of the pump to which this station’s
vacuum line is connected.
Special convey
When this option is enabled, the station’s
vacuum valve remains open for the convey
time, even if the station is not demanding
material and is indicating that it is full. When
disabled, the station’s vacuum valve opens
when there is demand from the station, and it
remains open until the convey time has elapsed
or material trips the volume-fill proximity switch.
Enable this option if and only if the station has
no flapper.
disabled,
enabled
disabled
Closed Loop
This option allows material to be conveyed and
processed without being contaminated by
outside influence (such as dust, other materials,
etc.)
Alarm Options
No convey
When this option is enabled, the controller
issues a “no convey” alarm if it has repeatedly
attempted to convey material to the station but
the flapper never opened during the dump
delay. (The number of attempts is controlled by
the next setting.)
disabled,
enabled
disabled
Usually this option should be enabled. At times,
you may wish to disable it during operation as a
stopgap measure for dealing with an alarm.
# attempts B4 alarm
Number of attempts before alarm: the number of 1–99
times the controller will attempt to convey
material to a station before it issues a “no
convey” alarm.
3
The setting for this option depends on (a) how
much material your mold uses to make each
part compared with the capacity of the receiver
and (b) how important it is to keep your mold
from running out of material and shutting down.
A higher setting will give you fewer alarms, at
the risk of emptying the receiver without
warning. A lower setting will give more frequent
alarms, at the risk of disrupting operations
unnecessarily.
24-Pump, 128-Station Controller
Chapter 6: Configurable Settings
65
Download from Www.Somanuals.com. All Manuals Search And Download.
Name
Partial convey
Description
Options
disabled,
enabled
Default
disabled
When this option is enabled, the controller
issues a “partial convey” alarm if it has
repeatedly attempted to convey material to the
station, and material has moved from the station
into the receiver, but the volume-fill proximity
sensor has never signaled that the station is full.
(The number of attempts is controlled by the
next setting.)
For a volume-fill station, this option should
usually be enabled. At times, you may wish to
disable it during operation as a stopgap
measure for dealing with an alarm. For a time-fill
station, disable this option.
# attempts B4 alarm
Number of attempts before alarm: the number of 1–99
times the controller will attempt to convey
material to a station before it issues a “partial
convey” alarm.
3
The setting for this option depends on the same
considerations as those given above for number
of attempts before a “no convey” alarm.
Option Input
Receiver low level
When this option is enabled, the controller
issues a “receiver level” alarm if material in the
receiver drains below the level of the receiver’s
low-level sensor.
disabled,
enabled
disabled
Enable this option if and only if your facility has
installed a low-level sensor for this station’s
receiver. At times, you may wish to disable it
during operation as a stopgap measure for
dealing with an alarm.
Bypass switch
Grinder empty
When this option is enabled, a switch at the
station is used to disable/”bypass” the station.
When this option is enabled, a proximity switch
is used to verify that material is present in the
grinder bin. The station will only be conveyed to
when the receiver is empty and the grinder bin
has material.
Grinder empty with
Alarm
When this option is enabled, alarm monitoring is
added to the grinder empty option described
above. If the grinder bin has material and the
receiver is full, a “grinder full” alarm is
generated.
Option output
Local alarm
When this option is enabled, the controller turns disabled,
disabled
disabled
on the local alarm light for any alarm at this
specific station.
enabled
Enable this option if and only if your facility has
installed a local alarm light for this station.
When this option is enabled, the controller
periodically sends compressed air backward
through the station’s air filter to dislodge
accumulated dust and debris.
Blow back
disabled,
enabled
Enable this option if and only if the station has
the equipment for compressed air filter cleaning.
24-Pump, 128-Station Controller
Chapter 6: Configurable Settings
66
Download from Www.Somanuals.com. All Manuals Search And Download.
Name
Description
Options
Default
Every n loads
Number of conveying cycles between filter
cleanings.
1–99
5
Adjust this setting based on experience. The
more dust and debris in your material line, the
smaller this number needs to be.
Number of pulses of compressed air sent
through the station’s filter during cleaning.
If blowback is not working as desired, the
service department may ask you to change this
setting.
Number of seconds that the each air pulse lasts 0.1–99.9 sec. 1.0 sec.
during filter cleaning.
If blowback is not working as desired, the
service department may ask you to change this
setting.
Number of seconds between air pulses during
filter cleaning.
If blowback is not working as desired, the
service department may ask you to change this
setting.
When this option is enabled, the controller
opens the slide gate between the station and
the receiver during the dump delay and during
blowback.
Enable this option if and only if the station has a
slide gate instead of a flapper and demand
switch.
# pulses
On time
Off time
Slide gate
1–99
5
0.1–99.9 sec. 1.0 sec.
disabled,
enabled
disabled
disabled
Purge
When enabled, this option allows the system to
empty the material line completely after every
convey to this station. The station’s pump
continues to draw without picking up material for
an extra period of time after conveying is
finished.
disabled,
enabled
Enable this option if and only if you are using a
purge valve for this station. This option cannot
be used with a volume-fill station.
Purge duration
Purge valve
Number of seconds allowed for purging. The
station’s vacuum valve remains open for the
convey time plus this time.
Adjust this setting to the amount of time
required for material to travel from the pickup
point (purge valve) to the station.
0–999 sec.
20 sec.
Number (address) for the purge valve used with 1–154
this station.
0 (= not
assigned)
Set this to match the number (address) for the
purge valve that services this station. If another
station has the purge valve that services this
station, enter the number of that station (range:
1–50). If a central purge valve services this
station, enter the number (address) of that valve
(range: 51–154).
Material set to n
Number for the material line that should be
connected to this station.
0 –150
0 (= not
assigned)
24-Pump, 128-Station Controller
Chapter 6: Configurable Settings
67
Download from Www.Somanuals.com. All Manuals Search And Download.
Name
Description
Options
Default
RPV (Remote
Proportioning Valve)
This option allows the system to use a remote
proportioning valve to mix two different
materials, typically virgin and regrind materials,
during a convey cycle. Touching RPVrepeatedly
at the Station n Setup screen steps through the
three choices.
disabled,
enabled PLC,
enabled local
disabled
Enable this option with PLC control if you will be
adjusting the mix from the controller’s touch
screen.
Enable this option with local control if the station
operator will be adjusting the mix using a timer
box at the station.
RPV material B
Percentage of the additive material to be
included in the mix. This setting applies only
when RPV is enabled with PLC control. The
system is set up so that, if there are any
inaccuracies in the proportions, the mix will
contain more Material A and less Material B
than specified here.
0 –100%
30%
Cycle time
Number of seconds for each cycle in depositing 5–100 sec.
Material A and Material B during the convey
time. This setting applies only when RPV is
enabled with PLC control. Example: If you set
convey time to 30 seconds, cycle time to 10
seconds, and Material B to 30% (so Material A
is 70%), the system will convey as follows:
Material A for 7 seconds
10 sec.
Material B for 3 seconds (end cycle 1)
Material A for 7 seconds
Material B for 3 seconds (end cycle 2)
Material A for 7 seconds
Material B for 3 seconds (end cycle 3)
In a volume-fill station, a cycle will be truncated
before completion if the station becomes full.
The cycle time should divide evenly into the
convey time.
24-Pump, 128-Station Controller
Chapter 6: Configurable Settings
68
Download from Www.Somanuals.com. All Manuals Search And Download.
6-3 Options for Pump Setup
Several of the items in this screen are not setup options but are instead intended for use
during operation. These items (hour meter and transferring stations to a standby pump) are
described in Chapter 4, “Operation.”
Name
Description
Options
Default
Idle Time Options
Auto Shutdown Delay
Length of time the pump continues to run
unloaded without demand from any station.
After this time has elapsed, the pump shuts
down to save power and to prevent wear on the
pump.
0–999 sec.
45 sec.
Adjust this setting to fit the needs of your facility
in trading off the savings against the costs
associated with waiting for a pump to start up
when there is a demand for material.
Alarm Options
Local alarm
When this option is enabled, the controller turns disabled,
disabled
disabled
on the local alarm light for any alarm at this
specific pump.
enabled
Enable this option if and only if your facility has
installed a local alarm light for this pump.
The ArmorBlock for each pump has two inputs
that you can wire to generate alarms for
situations of your choosing. These alarms can
be configured as standard or critical. Standard
means that the pump continues to operate.
Critical means that the pump is disabled.
For example, you may have a sensor that turns
on when material reaches the top of a filter-
chamber waste bin. When this option is
enabled, the controller issues an alarm if the
sensor wired to the input for Pump Fault #1
turns on.
Pump fault #1
disabled,
enabled
Enable this option if and only if your facility has
installed a miscellaneous alarm on the input for
Pump Fault #1 for this pump.
Pump fault #2
See the explanation for Pump fault #1 above.
Enable this option if and only if your facility has
installed a miscellaneous alarm on the input for
Pump Fault #2 for this pump.
disabled,
enabled
disabled
disabled
Filter Cleaning Options
Blow back
When this option is enabled, the controller
periodically sends compressed air backward
through the pump’s air filter to dislodge
accumulated dust and debris.
disabled,
enabled
Enable this option if and only if the pump has
the equipment for compressed air filter cleaning.
Every n loads
Number of conveying cycles to stations between 1–99
filter cleanings.
5
Adjust this setting based on experience. The
more dust and debris in your material line, the
smaller this number needs to be.
24-Pump, 128-Station Controller
Chapter 6: Configurable Settings
69
Download from Www.Somanuals.com. All Manuals Search And Download.
Name
Description
Options
Default
# pulses
Number of pulses of compressed air sent
through the pump’s filter during cleaning.
If blowback is not working as desired, the
service department may ask you to change this
setting.
1–99
5
On time
Off time
Number of seconds that the air compressor
remains on for each pulse during filter cleaning.
If blowback is not working as desired, the
service department may ask you to change this
setting.
0.1–99.9 sec. 1.0 sec.
0.5–99.9 sec. 1.0 sec.
Number of seconds between air pulses during
filter cleaning.
If blowback is not working as desired, the
service department may ask you to change this
setting.
Implosion with Seal
Valve
When this option is enabled, the controller
builds a vacuum in the filter chamber by
isolating it from the rest of the system with the
sealing valve. The vacuum is then released to
dislodge dust and debris.
Implosion without
Seal Valve
When this option is enabled, the controller
builds a vacuum in the filter chamber by
isolating it from the rest of the system by closing
all the station sequence valves assigned to that
pump. The vacuum is then released to dislodge
dust and debris.
Every n Loads
Number of conveying cycles to stations between 1–99
filter cleanings.
Adjust this setting based on experience. The
more dust and debris in your material line, the
smaller this number needs to be.
5
5
# Pulse(s)
Number of pulses of compressed air sent
through the pump’s filter during cleaning.
If blowback is not working as desired, the
service department may ask you to change this
setting.
1–99
Vacuum Time
Release Time
Number of seconds allowed for the vacuum to
build up in the filter chamber
Number of seconds allowed for the vacuum in
the filter chamber to dissipate.
24-Pump, 128-Station Controller
Chapter 6: Configurable Settings
70
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7: Troubleshooting
7-1 General Troubleshooting
Problem
Possible cause
Solution
The controller panel is not
connected to a power source.
Fuse/circuit breaker in the power
drop is blown/tripped.
Plug in the controller panel.
The controller panel doesn’t light
up at all.
Replace/reset.
Broken controller power switch.
Replace.
Reset the circuit breaker and
check the motor for the proper
amp draw on tag.
Replace the fuse/reset circuit
breaker.
The motor circuit breaker/
overload has tripped.
A pump package doesn’t run,
even though it is on line and its
indicator is lit.
Main fuse in power drop circuit
breaker has blown.
Motor contact is faulty.
Repair or replace as required.
Normal operation. When the
level drops, material conveys to
the hopper.
The bin below it is full if its
amber indicator light is off.
Using the controller, place the
hopper on line.
The field-installed station bypass Normal operation. Set the switch
The hopper is off line.
A vacuum hopper is being
bypassed in the loading cycle.
switch is simulating a Bin Full
condition.
so the hopper is back in the
loading sequence.
The field-installed station bypass
switch is bad or mis-wired.
Repair, replace, or rewire.
Time the hopper(s) during
loading, and set conveying times
to a few seconds less.
Conveying times are too long
(Time Fill mode only).
Check proximity sensors for
proper operation. Repair as
needed. Reset the conveying
times to a reasonable value, and
adjust as needed.
Repair shorting circuit.
Replace fuse with one that has a
proper rating.
Vacuum hoppers are over-filling.
Controller blows fuses.
Maximum conveying times are
too long and/or the controller
does not recognize the Hopper
Full proximity switch(es).
Power supply shorting out.
Improper fuse installed.
24-Pump, 128-Station Controller
Chapter 7: Troubleshooting
71
Download from Www.Somanuals.com. All Manuals Search And Download.
7-2 Alarms
The format for all station alarms is “Station n [alarm text],” for example, “Station 12 receiver
low level.” The format for all pump alarms is “Pump n [alarm text].” Any alarm that does not
start with “Station” or “Pump” is a system alarm.
The following tables list all alarms alphabetically, together with possible causes. A “critical”
alarm is one that causes the affected device to stop.
2. You can also see a list of alarms and their causes in the controller’s online help. To
display this information, touch the color key of statuses in the upper right-hand
corner of either the Station Status or the Pump Status screen, or touch Helpat any
other screen. When you are finished reviewing the help. touch Return.
Station Alarms
Alarm message
Blowback solenoid failure
Possible cause
Patch cord is cut or disconnected.
(Critical)
Solenoid has failed.
Patch cord is cut or disconnected.
Solenoid has failed.
Process generating excess scrap
Closed Loop Pump X Failure
Grinder full
Material line is blocked.
Vacuum line is blocked.
High vacuum
Station’s sequence valve has malfunctioned.
Note: After you have corrected the cause of this alarm, the alarm will be
cleared when the controller has conveyed a full load to this station.
Invalid pump assignment
Invalid pump assignment setting.
Convey time is too short.
Material container is empty.
Take-off compartment is not adjusted properly.
Material line is disconnected from source.
No convey
Vacuum line is disconnected from station.
Note: As a stopgap measure, you can disable the “no convey” alarm for
this station until the problem can be remedied. See pp. 41 and 65.
ArmorBlock is not installed properly.
ArmorBlock is not addressed properly.
ArmorBlock is defective.
Not present
(Critical)
ArmorBlock base is defective.
Power supply is not turned on.
Power supply is not connected properly
Power supply fuse blown.
Station ArmorBlock is not installed properly
ArmorBlock is defective.
Output power failure
(Critical)
Take-off compartment is not adjusted properly.
Pick-up wand is not positioned properly.
Convey time is too short.
Vacuum line has a leak.
Partial convey
Volume fill prox. Is not calibrated properly.
Note: As a stopgap measure, you can disable the “partial convey” alarm for
this station until the problem can be remedied. See pp. 41 and 659.
24-Pump, 128-Station Controller
Chapter 7: Troubleshooting
72
Download from Www.Somanuals.com. All Manuals Search And Download.
Alarm message
Possible cause
An assigned station has closed loop enabled and the pump has either
implosion with sealing valve or Local Alarm enabled.
Pump X Option Output Conflict
Patch cord is cut or disconnected
Solenoid has failed.
Purge Valve X Failure
ArmorBlock is not installed properly.
ArmorBlock is not addressed correctly.
ArmorBlock is defective.
Purge Valve X Not Present
ArmorBlock base is defective.
Patch cord is cut or disconnected.
Solenoid has failed.
Pick up wand is not positioned properly.
Take-off compartment is not adjusted properly.
Leak in vacuum line.
Purge Valve X Power Failure
Receiver Level
Patch cord is cut or disconnected.
Solenoid has failed.
RPV Failure
Patch cord is cut or disconnected.
Solenoid has failed.
Patch cord is cut or disconnected.
Solenoid has failed.
Sequence Valve Failure
Slide Gate Failure
24-Pump, 128-Station Controller
Chapter 7: Troubleshooting
73
Download from Www.Somanuals.com. All Manuals Search And Download.
Pump Alarms
Alarm message
Blowback Solenoid Failure
(Critical)
Possible cause
Patch cord is cut or disconnected.
Solenoid has failed.
Patch cord is cut or disconnected.
Clearing Valve Failure
Solenoid has failed.
Pump disconnect is off.
Failure
Patch cord is cut or disconnected.
Pump contactor has malfunctioned.
The alarm is user configured.
The alarm is user configured.
High vacuum switch is maladjusted.
High vacuum switch is wired incorrectly.
High vacuum switch is defected.
ArmorBlock is not installed properly.
ArmorBlock is not addressed correctly.
ArmorBlock is defective.
General Fault 1
General Fault 2
High Vacuum Switch Failure
Not Present
(Critical)
Base of ArmorBlock is defective.
Patch cord is cut or disconnected.
Pump disconnect is off.
Output Failure
Contactor has failed.
Power supply is not turned on.
Power supply is not connected properly
Power supply fuse blown.
Pump ArmorBlock not installed properly.
ArmorBlock is defective.
Output Power Failure
(Critical)
Contactor is mis-wired.
Contactor has failed.
Contactor Fault
Patch cord is cut or disconnected.
Solenoid has failed.
Sealing Valve Failure
Too Many Stations Assigned
Vent Solenoid Failure
More than 50 stations have been assigned to a pump.
Patch cord is cut or disconnected.
Solenoid has failed.
System Alarms
Alarm message
Possible cause
The alarm horn silence duration time has passed and at least one
alarm is still present on the system.
Alarm Horn Silence Expired
The alarm beacon suppress duration time has passed and at least
one alarm is still present on the system.
Control panel is not connected to flat cable.
Control panel network cable not installed correctly.
Power supply not turned on.
Alarm Strobe Suppress Expired
DeviceNet Scanner
Communications Failure
Power supply not connected properly.
Power supply fuse blown.
Main Control Panel Power
Supply Failure
Panel power supply fuse blown.
Panel power supply has failed.
Control panel is not connected to flat cable.
Control panel network cable is not installed correctly.
Power supply not connected properly.
Network Power Failure
24-Pump, 128-Station Controller
Chapter 7: Troubleshooting
74
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 8: Appendix
8-1 Warranty
The manufacturer warrants all equipment manufactured by it to be free from defects in
workmanship and material when used under recommended conditions. The company’s
obligation is limited to repair or replace FOB the factory any parts that are returned prepaid
within one year of equipment shipment to the original purchaser, and which, in the
company’s opinion, are defective. Any replacement part assumes the unused portion of this
warranty.
This parts warranty does not cover any labor charges for replacement of parts, adjustment
repairs, or any other work. This warranty does not apply to any equipment which, in the
company’s opinion, has been subjected to misuse, negligence, or operation in excess of
recommended limits, including freezing or which has been repaired or altered without the
company’s express authorization. If the serial number has been defaced or removed from the
component, the warranty on that component is void. Defective parts become the property of
the warrantor and are to be returned.
The company is not liable for any incidental, consequential, or special damages or expenses.
The company’s obligation for parts not furnished as components of its manufactured
equipment is limited to the warranty of the manufacturers of said parts.
Any sales, use, excise, or other tax incident to the replacement of parts under this warranty is
the responsibility of the purchaser.
The company neither assumes nor authorizes any other persons to assume for it any liability
in connection with the sale of its equipment not expressed in this warranty.
Many types of the manufacturer’s equipment carry an additional one-year service policy.
Consult your sales representative for specific details.
8-2 Optional Components
The following is a list of options that your controller may be equipped with:
230/1/60 Operation. Required to operate with a 230/1/60 supply voltage.
Additional audible/visual alarm with silence button. Alarm light and horn assembly that
can be remote mounted and wired into the controller to indicate an alarm condition.
Remote Interface.
24-Pump, 128-Station Controller
Chapter 8: Appendix
75
Download from Www.Somanuals.com. All Manuals Search And Download.
8-3 Drawings and Diagrams
Figure 20: 24-Pump, 128-Station Controller with 10" Display
Also, review electrical drawings supplied in the packet with this manual.
Note: Allow 12” of clearance on each side of the controller for ventilation and cables.
24-Pump, 128-Station Controller
Chapter 8: Appendix
76
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 21: Typical System Installation Layout
8-4 Spare Parts List
Quantity
Part Number
A0569859
Description
Fan grill with filter
4A Power supply
2A MDL fuse
10A FNQ fuse
2.5A MDL fuse
4A MDL fuse
1
1
1
1
1
1
739.00017.00
A0542203
A0568903
A0542205
A0542209
24-Pump, 128-Station Controller
Chapter 8: Appendix
77
Download from Www.Somanuals.com. All Manuals Search And Download.
8-5 Returned Material Policy
Credit Returns
Prior to the return of any material, authorization must be given by the manufacturer. A
RMS number will be assigned for the equipment to be returned.
Reason for requesting the return must be given.
All returned material purchased from the manufacturer is subject to 15% ($75.00 minimum)
restocking charge.
All returns are to be shipped prepaid.
The invoice number and date or purchase order number and date must be supplied.
No credit will be issued for material that is not within the manufacturer’s warranty period
and/or in new and unused condition, suitable for resale.
Warranty Returns
Prior to the return of any material, authorization must be given by the manufacturer. A
RMS number will be assigned for the equipment to be returned.
Reason for requesting the return must be given.
All returns are to be shipped prepaid.
The invoice number and date or purchase order number and date must be supplied.
After inspecting the material, a replacement or credit will be given, at the manufacturer’s
discretion, if the item is found to be defective in materials or workmanship. Purchased
components are covered under their specific warranty terms.
24-Pump, 128-Station Controller
Chapter 8: Appendix
78
Download from Www.Somanuals.com. All Manuals Search And Download.
8-6 Safety Tag Information
Controller Safety Tags
High Voltage Inside
Enclosure
Read Operation and
Installation Manual
8-7 Controller Identification (Serial Number) Tag
(Located on the side of the controller box)
Street Address
Town, State, Zip Code
Telephone Number
Fax Number
XXX CONTROL PANEL
Model No. XXX24-128
Serial No. 31K0182
Ph
115 Volt
60 Hz
1
Control Voltage 24VDC
24-Pump, 128-Station Controller
Chapter 8: Appendix
79
Download from Www.Somanuals.com. All Manuals Search And Download.
8-8 Technical Assistance (Contact Information)
Parts Department
[
]
[
]
Call toll-free 7am–5pm CST 800 423-3183 or call 630 595-1060, Fax [630] 475-7005
The ACS Customer Service Group will provide your company with genuine OEM quality parts
manufactured to engineering design specifications, which will maximize your equipment’s performance
and efficiency. To assist in expediting your phone or fax order, please have the model and serial
number of your unit when you contact us. A customer replacement parts list is included in this manual
for your convenience. ACS welcomes inquiries on all your parts needs and is dedicated to providing
excellent customer service.
Service Department
[
]
[
]
Call toll-free 8am–5pm CST 800 233-4819 or call 630 595-1060
[
]
Emergencies after 5pm CST, call 847 439-5655
We have a qualified service department ready to help. Service contracts are available for most
products.
Sales Department
[
]
Call 630 595-1060 Monday–Friday, 8am–5pm CST
Our products are sold by a worldwide network of independent sales representatives. Contact our Sales
Department for the name of the sales representative nearest you.
Contract Department
[
]
Call 630 595-1060 Monday–Friday, 8am–5pm CST
Let us install your system. The Contract Department offers any or all of these services: project planning;
system packages including drawings; equipment, labor, and construction materials; and union or non-
union installations.
24-Pump, 128-Station Controller
Chapter 8: Appendix
80
Download from Www.Somanuals.com. All Manuals Search And Download.
|